TSU 120 & 120e
User Manual
Part Number
1202129L1
1202129L2
January 1999
61202129L1-1C
Download from Www.Somanuals.com. All Manuals Search And Download.
ADTRAN Year 2000 (Y2K) Readiness Disclosure
ADTRAN has established a Year 2000 program to ensure that our products
will correctly function in the new millennium. ADTRAN warrants that all
products meet Y2K specifications regardless of model or revision.
Information about ADTRAN’s Y2K compliance program is available at the
following locations:
ADTRAN Web Site
Product Matrix
www.adtran.com
www.adtran.com/y2kfax.html
Faxback Document Line (256) 963-8200
Y2K plans and product certifications are listed in
the matrix.
Y2K Project Line
E-mail
(256) 963-2200
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes provide additional useful information.
Cautions signify information that could prevent service interrup-
tion.
Warnings provide information that could prevent damage to the
equipment or endangerment to human life.
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC Regulations Require that the Following Information be
Provided to the Customer
1. This equipment complies with Part 68 of the FCC rules. The required label
is attached to the bottom of the chassis.
2. An FCC compliant telephone cord and modular plug is provided with this
equipment. This equipment is designed to be connected to the telephone
network or premises wiring using a compatible modular jack which is Part
68 compliant. See installation instructions for details.
3. If your TSU 120 causes harm to the telephone network, the Telephone Com-
pany may discontinue your service temporarily. If possible, they will
notify you in advance. If advance notice is not practical, you will be noti-
fied as soon as possible. You will be advised of your right to file a com-
plaint with the FCC.
4. Your telephone company may make changes in its facilities, equipment,
operations, or procedures that could affect the proper operation of your
equipment. If they do, you will be given advance notice so as to give you
an opportunity to maintain uninterrupted service.
5. If you experience trouble with the equipment TSU 120, please contact
ADTRAN at (256) 963-8000 for repair/warranty information. The tele-
phone company may ask you to disconnect this equipment from the net-
work until the problem has been corrected, or until you are sure the
equipment is not malfunctioning.
6. This unit contains no user serviceable parts.
7. The following information may be required when applying to your local
telephone company for leased line facilities.
Service Type
1.544 Mbps -SF
REN/SOC
FIC
USOC
6.0N
6.0N
6.0N
6.0N
04DU9-BN RJ-48C
04DU9-DN RJ-48C
04DU9-1KN RJ-48C
04DU9-1SN RJ-48C
1.544 Mbps - SF and B8ZS
1.544 Mbps - ESF
1.544 Mbps - ESF and B8ZS
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Federal Communications Commission Radio Frequency
Interference Statement
This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to Part 15 of the FCC Rules. These lim-
its are designed to provide reasonable protection against harmful inter-
ference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio frequencies. Operation of this
equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own
expense.
Shielded cables must be used with this unit to ensure compliance with
Class A FCC limits.
Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user’s authority to op-
erate the equipment.
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
CANADIAN EMISSIONS REQUIREMENTS
This digital apparatus does not exceed the Class A limits for radio noise
emissions from digital apparatus as set out in the interference-causing
equipment standard entitled “Digital Apparatus,” ICES-003 of the De-
partment of Communications.
Cet appareil nuerique respecte les limites de bruits radioelectriques ap-
plicables aux appareils numeriques de Class A prescrites dans la norme
sur le materiel brouilleur: “Appareils Numeriques,” NMB-003 edictee
par le ministre des Communications.
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
CANADIAN EQUIPMENT LIMITATIONS
The Industry Canada Certification label identifies certified equipment.
This certification means that the equipment meets certain telecommu-
nications network protective, operational, and safety requirements.
The Department does not guarantee the equipment will operate to the
user's satisfaction.
Before installing this equipment, users should ensure that it is permissi-
ble to be connected to the facilities of the local telecommunications com-
pany. The equipment must also be installed using an acceptable method
of connection. In some cases, the company's inside wiring associated
with a single line individual service may be extended by means of a cer-
tified connector assembly (telephone extension cord). The customer
should be aware that compliance with the above conditions may not
prevent degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Cana-
dian maintenance facility designated by the supplier. Any repairs or al-
terations made by the user to this equipment, or equipment
malfunctions, may give the telecommunications company cause to re-
quest the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground
connections of the power utility, telephone lines and internal metallic
waterpipe system, if present, are connected together. This precaution
may be particularly important in rural areas.
Users should not attempt to make such connections themselves, but
should contact the appropriate electric inspection authority, or an elec-
trician, as appropriate.
The Load Number (LN) assigned to each terminal device denotes the
percentage of the total load to be connected to a telephone loop which is
used by the device, to prevent overloading. The termination on a loop
may consist of any combination of devices subject only to the equipment
that the total of the LNs of all devices does not exceed 100.
The ringer equivalence number (REN) assigned to each terminal adapter
is used to determine the total number of devices that may be connected
to each circuit. The sum of the RENs from all devices in the circuit
should not exceed a total of 5.0.
viii
Download from Www.Somanuals.com. All Manuals Search And Download.
Affidavit Requirements for Connection To Digital Services
• An affidavit is required to be given to the telephone company when-
ever digital terminal equipment without encoded analog content and
billing protection is used to transmit digital signals containing encod-
ed analog content which are intended for eventual conversion into
voiceband analog signals and transmitted on the network.
• The affidavit shall affirm that either no encoded analog content or
billing information is being transmitted or that the output of the de-
vice meets Part 68 encoded analog content or billing protection spec-
ifications.
• End user/customer will be responsible to file an affidavit with the lo-
cal exchange carrier when connecting unprotected CPE to a 1.544
Mbps or subrate digital services.
• Until such time as subrate digital terminal equipment is registered
for voice applications, the affidavit requirement for subrate services
is waived.
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
Affidavit For Connection Of Customer Premises Equipment To 1.544 Mbps
And/or Subrate Digital Services
For the work to be performed in the certified territory of
_______________________________________(telco name)
State of ___________________________________________
County of ________________________________
I, ___________________________________ (name),
(business address), ______________________ (telephone number) being
duly sworn, state:
I have responsibility for the operation and maintenance of the terminal
equipment to be connected to 1.544 Mbps and/or ________ subrate dig-
ital services. The terminal equipment to be connected complies with
Part 68 of the FCC rules except for the encoded analog content and bill-
ing protection specifications. With respect to encoded analog content
and billing protection:
( ) I attest that all operations associated with the establishment, main-
tenance, and adjustment of the digital CPE with respect to analog con-
tent and encoded billing protection information continuously complies
with Part 68 of the FCC Rules and Regulations.
( ) The digital CPE does not transmit digital signals containing encoded
analog content or billing information which is intended to be decoded
within the telecommunications network.
( ) The encoded analog content and billing protection is factory set and
is not under the control of the customer.
I attest that the operator(s)/maintainer(s) of the digital CPE responsible
for the establishment, maintenance, and adjustment of the encoded an-
alog content and billing information has (have) been trained to perform
these functions by successfully having completed one of the following
(check appropriate blocks):
x
Download from Www.Somanuals.com. All Manuals Search And Download.
( ) A. A training course provided by the manufacturer/grantee of the
equipment used to encode analog signals; or
( ) B. A training course provided by the customer or authorized repre-
sentative, using training materials and instructions provided by the
manufacturer/grantee of the equipment used to encode analog signals;
or
( ) C. An independent training course (e.g., trade school or technical
institution) recognized by the manufacturer/grantee of the equipment
used to encode analog signals; or
( ) D. In lieu of the preceding training requirements, the operator(s)/
maintainer(s) is (are) under the control of a supervisor trained in accor-
dance with _________ (circle one) above.
I agree to provide _________________ (telco's name) with proper docu-
mentation to demonstrate compliance with the information as provided
in the preceding paragraph, if so requested.
_________________________________Signature
_________________________________Title
_________________________________ Date
Transcribed and sworn to before me
This ________________________________________ (month/day/year)
_________________________________
Notary Public
My commission expires:
_________________________________
xi
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
When using your telephone equipment, please follow these basic safety
precautions to reduce the risk of fire, electrical shock, or personal injury:
1.
Do not use this product near water, such as near a bath tub, wash
bowl, kitchen sink, laundry tub, in a wet basement, or near a
swimming pool.
2.
3.
4.
Avoid using a telephone (other than a cordless-type) during an
electrical storm. There is a remote risk of shock from lightning.
Do not use the telephone to report a gas leak in the vicinity of the
leak.
Use only the power cord, power supply, and/or batteries indi-
cated in the manual. Do not dispose of batteries in a fire. They
may explode. Check with local codes for special disposal instruc-
tions.
SAVE THESE INSTRUCTIONS
xii
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY AND CUSTOMER SERVICE
ADTRAN will replace or repair this product within five years from the date
of shipment if the product does not meet its published specifications or if it
fails while in service. For detailed warranty, repair, and return information,
see the ADTRAN Equipment Warranty and Repair and Return Policy Proce-
dure.
Return Material Authorization (RMA) is required prior to returning equip-
ment to ADTRAN.
For Service, RMA requests, or more information, contact one of the numbers
found at the inside back page of this manual.
xiii
Download from Www.Somanuals.com. All Manuals Search And Download.
xiv
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Introduction .................................................................................... 1-1
TSU 120 Overview .................................................................................................... 1-1
Standard Features in the TSU 120 ................................................................... 1-2
TSU Option Modules ........................................................................................ 1-3
Option Module Architecture ........................................................................... 1-4
TSU 120 Configuration Applications .................................................................... 1-4
Chapter 2
Installation ...................................................................................... 2-1
Unpack, Inspect, Power Up .................................................................................... 2-1
Receipt Inspection ............................................................................................. 2-1
ADTRAN Shipments Include .......................................................................... 2-1
Customer Provides ........................................................................................... 2-1
Power Connection ............................................................................................. 2-2
Grounding Instructions ........................................................................................... 2-2
TSU 120 Interfaces ............................................................................................. 2-5
Network Interface ...................................................................................... 2-5
Network Test Interface .............................................................................. 2-5
Chain Port Input ........................................................................................ 2-6
Chain Port Output ..................................................................................... 2-6
Power Up Testing .............................................................................................. 2-7
Self-Test .............................................................................................................. 2-7
Initialization ....................................................................................................... 2-7
Set User Passcode ....................................................................................... 2-7
Set Unit Identification ............................................................................... 2-7
Set Chain Port Input .................................................................................. 2-8
Chain-In (PC) ............................................................................... 2-8
Chain-in/Chain Out .................................................................... 2-8
61202129L1-1
TSU 120 User Manual
xv
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Power-Up Procedure ........................................................................................2-9
Chapter 3
Operation ......................................................................................... 3-1
Front Panel .................................................................................................................3-1
LED Descriptions ...............................................................................................3-2
CSU Status ..........................................................................................................3-2
Operation Keys ...........................................................................................3-5
Set the Data Field ........................................................................................3-7
Display Only Data Fields ..........................................................................3-7
Data Port Identification ....................................................................................3-8
Front Panel Menu Structure .............................................................................3-9
Status ............................................................................................................3-9
Config (Configuration) ..............................................................................3-9
Util (Utilities) ..............................................................................................3-9
Test ...............................................................................................................3-9
Alternate Methods of Control ........................................................................3-10
SNMP .........................................................................................................3-11
Terminal Mode .........................................................................................3-12
TELNET .....................................................................................................3-12
Chapter 4
Status Menu..................................................................................... 4-1
Active Alarms ....................................................................................................4-3
View History ......................................................................................................4-4
Port Status ...........................................................................................................4-4
0.1 Nx56/64 Menu Items ...........................................................................4-5
DTE Data/Clock ..........................................................................4-5
DTE Status ....................................................................................4-5
Port Rate ........................................................................................4-5
DBU Data/CNTRL (TSU 120e only) .........................................4-5
DBU Contrl (TSU 120e only) ......................................................4-6
DBU Status (TSU 120e only) .......................................................4-6
xvi
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
0.2 DSX-1 Menu Items ............................................................................... 4-6
Remote Port ........................................................................................................ 4-7
Clear Port Alarm (Clear Port Alm) ................................................................. 4-7
ENET Status (TSU 120e only) .......................................................................... 4-7
Chapter 5
Network (NI) ............................................................................................................. 5-3
Network (NI) Menu Items ............................................................................... 5-3
TSU 120 Clock Sources ..................................................................................... 5-5
Network Timed .......................................................................................... 5-6
Base DSX-1 Timing .................................................................................... 5-7
Internal Timing ........................................................................................... 5-9
Secondary Timing .................................................................................... 5-10
Normal (CSU) Timing ............................................................................. 5-11
Unit Menu ........................................................................................................ 5-12
Map Exchange (Map Xchng) ......................................................................... 5-14
Map In Use: A(B) ............................................................................................ 5-14
DS0 Map A and DS0 Map B ........................................................................... 5-15
DSO Map Example .................................................................................. 5-16
Port Configuration (Port Config) ................................................................. 5-18
Chapter 6
Utility Menu.................................................................................... 6-1
Time/Date .......................................................................................................... 6-3
Factory Restore (Fact Restore) ......................................................................... 6-3
Change/Set a Passcode ............................................................................. 6-4
No Passcode Desired ................................................................................. 6-4
Unit ID ................................................................................................................ 6-4
Set the Unit Identification ......................................................................... 6-5
No Unit ID Desired .................................................................................... 6-5
Software Revision (Software Rev) .................................................................. 6-5
Port Utility (Option Ports) ............................................................................... 6-5
ENET Address (TSU 120e only) ...................................................................... 6-5
61202129L1-1
TSU 120 User Manual
xvii
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Serial Number ....................................................................................................6-5
CMD Mode .........................................................................................................6-5
Chapter 7
Test Menu ........................................................................................ 7-1
Network Tests ....................................................................................................7-3
Loopback Tests ...........................................................................................7-3
Test Patterns ................................................................................................7-5
All Zeros ........................................................................................7-5
QRSS Pattern ...............................................................................................7-5
PATTERN RESULT ....................................................................................7-6
Run Self-test .......................................................................................................7-7
Port Tests ............................................................................................................7-8
DBU Loopback (TSU 120e only) ..............................................7-10
Cancel Tests ......................................................................................................7-10
Chapter 8
Main Menu ................................................................................................................8-1
Map Configuration ......................................................................8-3
Initializing the Temp Map ..........................................................8-3
Editing the Temp Map ................................................................8-4
Applying the Temp Map ............................................................8-4
Reviewing Maps ..........................................................................8-4
Remote Menu Access ........................................................................................8-5
Management Configuration .............................................................................8-5
xviii
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Unit Access Table ....................................................................................... 8-5
Delete Unit .................................................................................... 8-7
OK .................................................................................................. 8-7
Poll Link Status Traps Sent ........................................................ 8-9
Telnet/Terminal Timeout .......................................................... 8-9
Exit ................................................................................................. 8-9
Flash Download ............................................................................................... 8-10
Quit Session ...................................................................................................... 8-10
Appendix A. Understanding SNMP ..................................................................A-1
Appendix B. Understanding TR-08 ................................................................... B-1
Appendix C. Network Pinouts ........................................................................... C-1
Appendix D. System Messages ...........................................................................D-1
Appendix E. Specifications ..................................................................................E-1
Index ................................................................................................................. Index-1
61202129L1-1
TSU 120 User Manual
xix
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
xx
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 1-1. TSU Option Modules ......................................................................... 1-4
Figure 2-1. TSU 120e Rear Panel .......................................................................... 2-4
Figure 2-2. TSU 120 Rear Panel ............................................................................ 2-4
Figure 2-3. TSU 120 Interfaces .............................................................................. 2-5
Figure 2-4. Example of Chain-in .......................................................................... 2-8
Figure 3-1. TSU 120 Front Panel Layout ............................................................. 3-3
Figure 3-3. Display and Data Fields .................................................................... 3-7
Figure 4-1. Complete Status Menu Tree ............................................................. 4-1
Figure 4-3. Display of Alarm Message ................................................................ 4-4
Figure 5-1. Complete Configuration Menu ........................................................ 5-2
Figure 5-2. Network Timed Clock Source .......................................................... 5-6
Figure 5-3. DSX-1 Timed Clock Source ............................................................... 5-7
Figure 5-4. DTE Timed Clock Source .................................................................. 5-8
Figure 5-5. Internal Clock Source ........................................................................ 5-9
Figure 5-6. Secondary Timing ............................................................................ 5-10
Figure 5-7. Normal (CSU) ................................................................................... 5-11
Figure 5-8. DS0 Map Designations .................................................................... 5-15
Figure 5-9. Create Temp Selection Screen ........................................................ 5-17
Figure 6-1. Complete Utility Menu Tree ............................................................. 6-2
Figure 7-1. Complete Test Menu Tree ................................................................. 7-2
Figure 7-2. Network Loopback Tests .................................................................. 7-4
Figure 8-1. Telnet/Terminal Main Menu ........................................................... 8-1
Figure 8-2. DS0 Temp Map ................................................................................... 8-2
Figure 8-3. Unit Access Table ............................................................................... 8-6
61202129L1-1
TSU 120 User Manual
xxi
Download from Www.Somanuals.com. All Manuals Search And Download.
List of Figures
xxii
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 3-1. Front Panel Descriptions ...................................................................3-1
Table A-1. How to Configure Network Manager MIB ....................................A-5
Table C-1. Network Pinouts ................................................................................C-1
Table C-2. Control In/Chain in Pinout .............................................................C-2
Table C-3. Chain Out Pinout ...............................................................................C-3
Table C-4. V.35 Pinout - Nx56/64 DTE .............................................................C-4
Table C-5. Pinout Connectors for Modular Jack Interface ..............................C-5
Table C-6. 10BaseT Ethernet (TSU 120e only) ..................................................C-6
61202129L1-1
TSU 120 User Manual
xxiii
Download from Www.Somanuals.com. All Manuals Search And Download.
List of Tables
xxiv
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Chapter 1
TSU 120 OVERVIEW
This manual covers the use of the following products:
•
TSU 120
TSU 120e
•
Unless otherwise stated, the TSU 120 refers to both products.
The TSU 120 is a T1/FT1 multiplexer with an Nx56/64 V.35
data port, a DSX-1 (PBX) interface, one option slot, and embed-
ded SNMP management. The TSU 120e offers a built-in dial
back up feature for the Nx port. The TSU 120’s option slot
accepts one of many available option modules for voice and
data applications.
The TSU 120 links user data sources such as local area network
(LAN) bridges and routers, computers, CAD systems, telecon-
ferencing equipment, and PBXs. Through the use of multiple
data ports, the TSU 120 can simultaneously connect one or
more of these devices to a T1 circuit. The amount of bandwidth
allocated to each port is custom-programmable. You can manu-
ally allocate bandwidth or set the bandwidth to automatically
change at predetermined times to use the available bandwidth
most advantageously. Changes in the configuration do not dis-
rupt data flow in channels that are not being reconfigured. The
unique architecture and the availability of option modules pro-
vides a path for growth to accommodate future requirements.
61202129L1-1
TSU 120 User Manual
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1. Introduction
The TSU 120 offers a wide variety of network management
options. You can manage via SNMP through the 10BaseT (TSU
120e only) or chain-in ports. If you are using T-WATCH Pro, a
Microsoft Windows® -based program, you can manage the
TSU 120 via the same 10BaseT (TSU 120e only) or chain-in
ports. An enhanced VT 100 terminal interface is also provided.
Standard Features in the TSU 120
The following list describes the standard features in both the
TSU 120 and the enhanced TSU 120e.
•
•
•
A single T1 interface.
An Nx56/64 V.35 port and DSX-1 (PBX) interface.
SNMP, Telnet, and T-WATCH Pro management via SLIP or
10BaseT (10BaseT is only in the TSU 120e).
•
•
•
Ability to proxy for “agentless” units
Enhanced terminal mode
An inband communication channel requiring only 8k of
bandwidth from a single DS0.
•
•
•
One option slot to house option modules with up to four ad-
ditional ports, including voice and data.
Allows mix of port types to meet the data interface require-
ments.
Easy configuration capabilities using simplistic menus dis-
played in a liquid crystal display (LCD) window operated
by a front panel keypad.
•
Two programmable configuration maps that define the
bandwidth allocation between data ports.
•
•
•
Data drop and insert, as well as full drop and insert.
Flash memory for software updates.
Timing is selectable from the network, from the Nx56/64 or
DSX-1 ports, internally, or from a secondary interface.
•
Fractional T1 loopbacks as defined in Annex B of ANSI
T1.403-1995
•
•
QRSS; 511 test patterns using Nx option.
Integrated Dial Backup Capability in the Base Nx56/64 port
( TSU 120e only)
•
Extensive self-testing and monitoring provides assurance of
proper operation.
1-2
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1. Introduction
TSU Option Modules
Some of the option modules available for the TSU 120 are:
Name Description
DSX-1
Short haul T1 interface for operation
with a PBX (Terminal Interface).
Full Drop and Insert
Permits the dropping of data and
insertion of new data into the same
DS0 time slot.
Includes a long haul DS1 interface.
Can be used as a second DS1
interface to provide up to 3 MB
aggregate throughput.
Nx56/64 Serial Interface Provides a V.35 serial interface in
either single or dual versions.
Voice Interface
OCU DP
2/4 channel FXS/FX0/E&M.
Interfaces to DDS or 4-wire
Switched 56.
DSU DP
Dial Backup
U-BR1TE
Router
Provides two sync or async ports
(232 or V.35).
Allows data backup upon network
T1 failure.
Allows ISDN lines to be extended
over a T1 line.
Provides 10BaseT port and integrated
IP/IPX routing.
NxIQ
Provides Frame Relay monitoring
capabilities.
61202129L1-1
TSU 120 User Manual
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1. Introduction
Option Module Architecture
The TSU 120 features a unique architecture that allows you to
add one option module and plug-on board to accommodate
another application. See Figure 1-1.
DSX-1
TSU 120
Module
OCU-DP
Module
Plug on
V.35
TSU 120e
A
1
B
2
C
3
D
E
TD1
4
RD1
TD2
F
6
RD2
5
TDN
ALM
/TST
RD
NEXT
7
N
PREV
ADD
8
DELETE
0
SHIFT
9
QUICK
#
V.35
Module
Plug on
OCU DP
D&I
Module
DUAL
Voice
Plug on
Dual Voice
Figure 1-1. TSU Option Modules
TSU 120 CONFIGURATION APPLICATIONS
The following example illustrates possible configurations of
TSU 120 applications.
The base Nx54/64 provides a V.35 interface to a router. The
PBX is interfaced to the TSU 120 with the base DSX-1 interface.
An OCU DP module and OCU DP plug-on board provide two
Switched-56 circuits for video conferencing. The 10BaseT port
allows SNMP network management over the LAN (TSU 120e
only). See Figure 1-2.
PBX
TSU 120
TSU 120e
A
1
B
2
C
3
D
E
TD1
4
RD1
TD2
F
6
RD2
5
TDN
ALM
/TST
RDN
NEXT
7
PRV
AD
D
8
DELETE
0
SHIFT
9
QU
#
C
ROUTER
(TSU 120e only)
10 BaseT LAN
VIDEO
CONFERENCING
SNMP NETWORK
MANAGEMENT WORKSTATION
Figure 1-2. Router, PBX, Video Conferencing Application Set Up
1-4
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Chapter 2
UNPACK, INSPECT, POWER UP
Receipt Inspection
Carefully inspect the TSU 120 for any shipping damages. If
you suspect damage, file a claim immediately with the carrier
and then contact ADTRAN Customer Service (see inside the
last page of this manual). If possible, keep the original ship-
ping container for use in shipping the TSU 120 back for repair
or for verification of damage during shipment.
ADTRAN Shipments Include
•
The TSU 120
•
Two-line interface cable: an 8-position modular to 8-posi-
tion modular (15 ft.)
•
•
•
•
Loopback plug
DB 15 to RJ adapter
DB 25 to RJ adapter
An 8-position modular cable for connection to the chain-in
port (6 ft.)
•
The TSU 120 and TSU 120e User Manuals
Customer Provides
•
Cables for any expansion modules to be used with the TSU
120
•
10BaseT cable for connection to a LAN or router, if you plan
to use remote management features (TSU 120e only)
61202129L1-1
TSU 120 User Manual
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2. Installation
Power Connection
Each TSU 120 is equipped with a captive eight-foot power cord,
terminated by a three-prong plug which connects to a
grounded power receptacle.
Power to the TSU 120 must be from a grounded 90-120 VAC, 50/
60 Hz source.
GROUNDING INSTRUCTIONS
Grounding instruction information from the Underwriters' Lab-
oratory UL 1950 3rd Edition, is provided in this section.
An equipment grounding conductor that is not smaller in size
than the ungrounded branch-circuit supply conductors is to be
installed as part of the circuit that supplies the product or sys-
tem. Bare, covered, or insulated grounding conductors are
acceptable. Individually covered or insulated equipment
grounding conductors shall have a continuous outer finish that
is either green, or green with one or more yellow stripes. The
equipment grounding conductor is to be connected to ground
at the service equipment.
The attachment-plug receptacles in the vicinity of the product
or system are all to be of a grounding type, and the equipment
grounding conductors serving these receptacles are to be con-
nected to earth ground at the service equipment.
A supplementary equipment grounding conductor shall be
installed between the product or system and ground that is in
addition to the equipment grounding conductor in the power
supply cord.
The supplementary equipment grounding conductor shall not
be smaller in size than the ungrounded branch-circuit supply
conductors. The supplementary equipment grounding con-
ductor shall be connected to the product at the terminal pro-
vided, and shall be connected to ground in a manner that will
retain the ground connection when the product is unplugged
from the receptacle. The connection to ground of the supple-
2-2
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2. Installation
mentary equipment grounding conductor shall be in compli-
ance with the rules for terminating bonding jumpers at Part K
or Article 250 of the National Electrical Code, ANSI/NFPA 70.
Termination of the supplementary equipment grounding con-
ductor is permitted to be made to building steel, to a metal
electrical raceway system, or to any grounded item that is per-
manently and reliably connected to the electrical service equip-
ment ground.
Bare, covered, or insulated grounding conductors are accept-
able. A covered or insulated grounding conductor shall have a
continuous outer finish that is either green, or green with one
or more yellow stripes.
The supplemental grounding conductor shall be connected to
the equipment using a number 8 ring terminal. The terminal
should be fastened to the grounding lug provided on the rear
panel of the equipment. The ring terminal should be installed
using the appropriate crimping tool (AMP P/N 59250 T-EAD
Crimping Tool or equivalent).
61202129L1-1
TSU 120 User Manual
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2. Installation
Identification of Rear Panel Layout
The configuration of the rear panel of the TSU 120e is shown in
Figure 2-1. The TSU 120 rear panel is shown in Figure 2-2.
Monitor/Test Jacks for DSX-1
Connection
10 Base T Connection for LAN
DSX-1
OPTION
SLOT 1
Power
Switch
CAUTION-RISK OF ELECTRIC SHOCK
SUPPLEMENTAL EARTH GROUND MUST BE CONNECTED PRIOR TO
CONNECTION OF TELECOMMUNICATIONS WIRING
PORT 0.2
10 BASE T
P
O
W
E
PORT 0.1
R
DSX-1
OUT
IN
IN T-MON
C
H
A
I
V.35
N
90-120VAC
50/60HZ.2A
OUT R-MON
NETWORK
IN
OUT
T1 Network
Connection
Control In/Out
Connection
Monitor/Test Jacks
for T1
V.35 Connector
Figure 2-1. TSU 120e Rear Panel
Monitor/Test Jacks for DSX-1
Connection
DSX-1
OPTION
SLOT 1
Power
Switch
CAUTION-RISK OF ELECTRIC SHOCK
SUPPLEMENTAL EARTH GROUND MUST BE CONNECTED PRIOR TO
CONNECTION OF TELECOMMUNICATIONS WIRING
PORT 0.2
P
O
W
E
PORT 0.1
R
DSX-1
OUT
IN
IN T-MON
C
H
A
I
V.35
N
90-120VAC
50/60HZ.2A
OUT R-MON
NETWORK
IN
OUT
T1 Network
Connection
Control In/Out
Connection
Monitor/Test Jacks
for T1
V.35 Connector
Figure 2-2. TSU 120 Rear Panel
2-4
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2. Installation
TSU 120 Interfaces
The TSU 120 is equipped with a Nx56/64 data port, a DSX-1
interface, an option slot, management interfaces, and a T1
interface, in the rear panel. See Figure 2-3.
10BaseT LAN
(TSU 120e only)
PC or Modem
Control
Input
Chain
Output
Chain
Input
Chain
Output
TSU 120e
TSU 120e
NI
NI
DSX-1
Network
DSX-1
Nx56/64 Option
Nx56/64 Option
V.35
V.35
DSX-1
PBX
Network Interface
The Network Interface (NI) port provides the connection to the
T1. This port complies with the applicable ANSI and AT&T
standards. For more information see the Wiring section in
Appendix C, on page C-1.
Network Test Interface
The IN and OUT test jacks for the network interface provide
intrusive test capability for the incoming T1. By connecting to
these jacks with test equipment, the T1 connection will be bro-
ken, and the test equipment will terminate the incoming T1.
The R-MON test jack provides a bridged access jack for non-
intrusive monitoring of the incoming T1. When connected to
this jack, the test equipment should be configured for a bridged
termination.
Nx56/64 Serial Interface (TSU 120e only)
The Nx56/64 provides a serial V.35 port that operates from
56 kbps to 1.536 Mbps. This port provides 511 pattern genera-
tion and detection and remote loopback capability.
61202129L1-1
TSU 120 User Manual
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2. Installation
DSX-1 (PBX) Interface
The DSX-1 Interface provides a short haul T1 for a PBX or other
equipment. This port complies with ANSI T1.102.
DSX-1 Test Interface
The IN and OUT test jacks for the DSX-1 interface provide intru-
sive test capabilities for the T1 connecting the TSU 120 to the
PBX or other customer premise equipment. By connecting to
these jacks with test equipment, the DSX-1 connection will be
broken, and the test equipment will be terminating the DSX-1
connection from the PBX.
The T-MON test jack provides a DSX monitor access jack for
non-intrusive monitoring of the T1 connecting the TSU 120 to
the PBX or other customer premise equipment. When con-
nected to this jack, the test equipment should be configured for
a DSX MON termination.
Chain Port Input
The chain port input provides an EIA-232 input from a PC or a
modem for control of the TSU 120. You can also use it as a chain
tion see the Wiring section in Appendix C, on page C-1.
Chain Port Output
The chain port output provides an EIA-232 output to chain con-
trol to other TSUs. For more information see the Wiring section
in Appendix C, on page C-1.
10BaseT Interface (TSU 120e only)
The 10BaseT interface provides the LAN interface for manag-
ing the TSU 120 with SNMP or T-WATCH Pro. For more infor-
mation see the Wiring section in Appendix C, on page C-1.
2-6
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2. Installation
Power Up Testing
When shipped from the factory, the TSU 120 is set to factory
default conditions. At the first application of power, the unit
automatically executes a memory self-test. A full self-test can
be run from the front panel. A passcode and Unit ID may be
set using the
ENU.
UTIL M
Self-Test
Upon a power-up, the LCD displays
MEMORY TEST NOW TESTING
and the Test LEDs are illuminated. When the self-test is com-
pleted with no failures detected, the lights up and the
OK LED
LCD momentarily displays EMORY EST S ASSED. If a fail-
M
T
( ) P
ure is detected, a list of failures is displayed in the LCD win-
dow.
Initialization
Set User Passcode
The TSU 120 is designed to operate with or without the use of a
passcode. The default condition is without a passcode.
If the unit is to be remotely accessed using T-WATCH Pro, you
must enter a passcode. When managing a number of units, the
passcode can be the same for all the units.
The passcode should be a number easily remembered. Once
entered, the passcode is required to access any operation other
than viewing. See Change/Set a Passcode on page 6-4 for details.
Set Unit Identification
The Unit ID sets the unit to respond to remote control (con-
trolled by a device other than the front panel or terminal). If no
Unit ID is recorded it is not possible to operate from any remote
control device, including the local PC for T-WATCH Pro or
SNMP. See Unit ID on page 6-4 for details.
61202129L1-1
TSU 120 User Manual
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2. Installation
Set Chain Port Input
The TSU 120 can be configured from the chain port input when
T-WATCH Pro, SNMP, or the terminal interface are being used.
In this case, the chain port baud rate must also be selected.
Chain-In (PC)
The unit can be controlled from an external PC connected
directly or via modem to the chain-in port. When using chain-
in, the selection of the chain-in port baud rate from 9600 (fac-
tory default), 1200, 2400, 19200, or 38400 must be made using
the NIT ONFIGURATION ENU. See Unit Menu on page 5-12 for
U
C
M
details.
Unless locked out externally, the front panel can also control
the unit.
Chain-in/Chain Out
TSU 120 units and other TSUs can be linked together to form a
chain. Figure 2-4 provides an example of a chain-in arrange-
ment with a PC or a modem. The first TSU 120 in the chain
receives controlling input from the PC or modem.
PC or Modem
Chain
In
Chain
Out
Chain
Input
Chain
Out
Chain
In
Chain
Out
TSU 120/
TSU 100/TSU
TSU 120
TSU 120/
TSU 100/TSU
Figure 2-4. Example of Chain-in
Subsequent TSUs in the chain are in a position to intake infor-
mation from another TSU. This in-taking of information from
another TSU in the chain is identified as chain-in. The baud
rate for the chained units must match that of the first unit.
Unless locked out externally, the front panel can also control
the unit.
2-8
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2. Installation
At this point, the Unit Initialization procedure is concluded. If
the unit is to be configured remotely, there are no additional
items necessary to complete prior to executing remote configu-
ration.
The Passcode, the Unit ID, and the Control Port settings are
stored in a nonvolatile memory. This ensures they are operable
for subsequent power-up sequences.
Power-Up Procedure
After the unit has been put into operation with the initial
power-up and initialization, the subsequent power-up proce-
dure includes only the power-up self-test followed by the
request for a passcode (password) if this option was selected
during initialization. Use the Number Keys to enter the previ-
ously recorded passcode and press Enter.
61202129L1-1
TSU 120 User Manual
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2. Installation
2-10
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Chapter 3
FRONT PANEL
The TSU 120 front panel monitors operation and controls the
configuration of the unit. The TSU 120 front panel is shown on
page 3-3. Figure 3-1 describes each part of the front panel.
Table 3-1. Front Panel Descriptions
Name
Description
LCD Window
Displays menu items and messages in two
lines by 16 characters and alarm and status
information.
Enter
Selects active menu items.
To select a menu item, press the number of
the item. The menu item flashes,
indicating it is activated. Press Enter to
select the menu item.
Up and Down
Arrows
Up and Down Arrows scroll through and
activate the submenu items available in
the current menu. When the submenu
items are scrolled, the flashing cursor
indicates the active parameters.
Cancel
Pressing the Cancel key stops the current
activity and returns to the previous menu.
Repeat until the desired menu level is
reached. When a submenu item is
displayed, press Cancel to exit the current
display and return to the previous menu.
61202129L1-1
TSU 120 User Manual
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3. Operation
Table 3-1. Front Panel Descriptions
Name
Numeric Keypad
Description
The numeric keypad contains the numbers
0 through 9 which are used to activate
menu items and enter information (such as
the IP address).
Shift (entering
special function
keys)
Enter special function keys by pressing
and holding Shift before pressing the key
representing the desired character.
To activate a special function key rather
than a number, press and hold Shift; then
the button. See Operation Keys on page 3-5
for a description of the function keys.
If a key is pressed without using Shift, the
numbered item becomes active instead of
the special function key.
LED Descriptions
CSU Status
The CSU status LEDs display the operational condition of the
network interface located on the controller board in the unit.
GREEN
Indicates the operation is in the normal mode and no
errors have been detected.
OK (
)
EST
Indicates that the network interface is operating in a test
mode. This includes a self-test or a test loopback. When
lighted, this LED also indicates that normal data flow is
not occurring on the network interface.
T
(
YELLOW
)
RROR RED
)
Indicates an error such as a BPV, OOF, or CRC.
E
(
LARM RED
Indicates an alarm condition has been detected. When the
alarm condition is no longer valid, the OK LED activates
(turns on). To view an alarm condition, select the active
A
(
)
alarm menu item or select LARM by pressing Shift+8. If
A
the alarm conditions have been corrected, the alarm which
caused the activation of the Alarm LED can be viewed
under the Unit History menu.
3-2
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3. Operation
.
No
Description
Action/Status
1
LCD Window
Displays menu items and messages in 2 lines by 16
characters
2
Up and Down Arrows
Scroll through and activate the submenu items available in
the current menu. The flashing cursor indicates the active
parameter
3
4
5
6
7
8
9
Enter Key
Selects active item
Alarm
Quick access to the active display menus
Clears data/results fields
Clear
Shift
Provides access to special function keys
Operation is in normal mode with no detected errors
Active when the module is in test mode
Active when an alarm condition has been detected
Operation is in normal mode with no detected errors
Active when the module is in test mode
Active when an alarm condition has been detected
Stops current activity and returns to the previous menu
Copies last data entered into the current DS0
Operation is in normal mode with no detected errors
Active when the network interface is in test mode
Indicates errors such as BPV, OOF or CRC
Returns to the main menu
OK (DSU/DSX Status)
Test (DSU/DSX Status)
Alarm (DSU/DSX Status)
10 OK (Module Status)
11 Test (Module Status)
12 Alarm (Module Status)
13 Cancel
14 Copy
15 OK (CSU Status)
16 TEST (CSU Status)
17 Error (CSU Status)
18 Home
19 Alarm (CSU Status)
Active when an alarm condition has been detected on the
network interface
Figure 3-1. TSU 120 Front Panel Layout
61202129L1-1
TSU 120 User Manual
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3. Operation
DSU/DSX Status
The DSU/DSX status LEDs display the operational condition
of the Nx56/64 and DSX-1 parts included in the TSU 120. It
also reflects the status of the DBU in the TSU 120e.
GREEN
OK (
Indicates the operation is in the normal mode
and no errors have been detected.
)
EST
Indicates that one of the interfaces is operating
in a test mode. This includes a self-test or a test
loopback. When lighted, this LED also indicates
that normal data flow is not occurring in at least
one of the module ports.
T
(
YELLOW
)
LARM RED
)
Indicates an alarm condition has been detected.
When the alarm condition is no longer valid, the
A
(
activates (turns on). To view an alarm
OK LED
condition, select the active alarm menu item or
select Alarm by pressing Shift+8. If the alarm
conditions have been corrected, the alarm
which caused the activation of the Alarm LED
can be viewed under the Unit History Menu.
Module Status
The module status LEDs display the operational condition of
ports installed in the option slots.
GREEN Indicates the operation is in the normal mode
OK (
)
and no errors have been detected.
EST
T
Indicates that one of the interfaces is operating
YELLOW
in a test mode. This includes a self-test or a test
loopback. When lighted, this LED also indicates
that normal data flow is not occurring in at least
one of the module ports.
(
)
3-4
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3. Operation
LARM RED Indicates an alarm condition has been detected.
A
(
)
When the alarm condition is no longer valid,
the OK LED activates (turns on). To view an
alarm condition, select the active alarm menu
item or select Alarm by pressing Shift 8. If the
alarm conditions have been corrected, the alarm
which caused the activation of the Alarm LED
can be viewed under the Unit History menu.
Operation Keys
OPY
Used in the DS0 mapping menu operations to copy
the last data entered into the current DS0. This key
operates without pressing the Shift key.
C
OME
Returns home to the Main Menu from any menu
location.
H
A
LARM Used as quick access to the active alarm display
menus. This can be activated while any other menu
item is in use. When the Alarm menu is exited, the
unit returns to the location of the same menu that
was active when Alarm was selected.
LEAR
Used in various menus to clear data/result fields.
C
General Menu Operation
The TSU 120 uses a multilevel menu structure containing both
menu items and data fields. All menu operations and data are
displayed in the LCD window. The menu items are numbered
and can be viewed by scrolling with the Up and Down arrows.
ATA IELD You can edit menu items followed by a colon (:).
D
F
ISPLAY
You cannot edit menu fields followed by an
D
NLY IELD equal symbol (=). This symbol identifies a field
O
F
used for value display only.
RROWS
Menus that display small up or down arrows in
the lower right corner indicate there are more
menu items than are visible on a two-line LCD.
Access the additional items with the up or down
arrows. You can also access undisplayed menu
items by using the appropriate menu number.
A
61202129L1-1
TSU 120 User Manual
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3. Operation
Select and Activate a Menu Item
To choose menu items, place the cursor on the desired menu
item by pressing the number corresponding to the menu item
or highlighting the menu item with the up and down arrow.
Activate the LARM IST option from the TATUS ENU by
A
L
S
M
using the following steps.
Step
Action
1
Activate the STATUS MENU using the arrow keys or by
pressing 1. The cursor will flash on the number next
to the activated selection.
2
3
4
Press Enter.
View the submenu items by using the arrow keys.
Choose an item on the submenu such as ACTIVE
ALARMS.
5
Select the submenu with the Arrow Keys or by
pressing 3.
6
7
Press Enter.
View the Alarm List by using the arrow keys.
.
1) NI PERF RPTS
2) NI ERRORS
3) ACTIVE ALARMS
4) VIEW HISTORY
5) PORT STATUS
(ALARM LIST)
END OF LIST
1)STATUS
6) REMOTE PORT
7) CLEAR PORT ALM
8) ENET STATUS
9) SLIP STATUS
Figure 3-2. Example of Basic Front Panel Menu Tree
3-6
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3. Operation
Set the Data Field
You can edit data fields preceded by a colon (:).
Step
1
Action
Position the cursor on the submenu item number, and
press Enter. The cursor moves to the data field, (to the
right of the submenu item name).
2
3
Using the Arrow Keys, scroll to scan the available value
settings. The value settings display one at a time in the
data field position.
When the desired value is displayed in the data field
position, press Enter to set that value. When the value
is set, the cursor moves back to the submenu item
position indicating the operation is complete.
4
5
Select another submenu field, or press Cancel to return
to the submenu.
Press Cancel before pressing Enter to void any data
changes. The original data value is restored and the
cursor returns to the submenu field.
Display Only Data Fields
Data fields preceded by an equal (=) symbol cannot be edited.
See Figure 3-3.
Data Field
Display Field
Figure 3-3. Display and Data Fields
Press Enter to move the cursor to the data field. Use arrows to
select
and press Enter. The unit automatically sets the
AUTO
Line Build Out. The display field shows the value actually set.
61202129L1-1
TSU 120 User Manual
3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3. Operation
The equal symbol after LBO in the second line indicates the
information that follows is displayed data and cannot be
edited.
Exit Any Menu Field Operation Or Display
Press Cancel as many times as needed to return to the desired
menu level or press Shift+0 (Home) to return to the main menu.
Data Port Identification
When configuring the unit, menu selections will include
options from data port submenus. Selecting data ports is neces-
sary because the TSU 120 uses a slot-port method to identify
which data port the menu item is referencing. If a module con-
taining a PBX DSX-1 option card with an Nx56/64 plug-on
interface is installed in the option slot, it would be designated
as:
DSX-1 Passthru=1.1
Where slot=1 and port =1.
The DSX-1 is located in the option slot and is the first port in
that slot.
Nx56/64=1.2
Where slot=1 and port=2.
The Nx is located in the slot and is the second port in that
slot.
The ports that are built into the TSU 120 are referenced as Slot
0. The Nx56/64 would be designated as 0.1 and the DSX-1
would be referenced as 0.2.
3-8
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3. Operation
Front Panel Menu Structure
The TSU 120 uses a multilevel menu structure containing both
menu items and data fields. All menu operations and data dis-
play in the LCD window.
The opening menu is the access point to all other operations.
Each Main menu item has several functions and submenus to
identify and access specific parameters.
The front panel LCD of the Main menu contains the following
options
1=STATUS
2=CONFIG
3=UTIL
4=TEST
Status
The Status menu displays all relevant information for the net-
work and DTE interfaces. For detailed information on status
options, see Chapter 4, Status Menu on page 4-1.
Config (Configuration)
The Configuration menu displays and sets the TSU 120 opera-
tional configuration, including all network interface parame-
ters, the allocation of the DS0s, and the port parameters. For
detailed information on configuration options, see Chapter 5,
Configuration Menu on page 5-1.
Util (Utilities)
The Utility menu displays and sets system parameters. For
detailed information on utility options, see Chapter 6, Utility
Menu on page 6-1.
Test
The Test menu initiates different types of unit tests and dis-
plays test results in the LCD window. For detailed information
on test options, see Chapter 7, Test Menu on page 7-1.
61202129L1-1
TSU 120 User Manual
3-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3. Operation
Alternate Methods of Control
T-WATCH Pro (ADTRAN PC Program)
T-WATCH Pro is the ADTRAN PC control program. It provides
complete control over the configuration of the TSU 120 using a
graphical interface. The T-WATCH Pro program displays the
same status and performance data as the front panel LCD. This
data is displayed in the form of tables and graphs.
The T-WATCH Pro program has the following capabilities:
•
Interfaces with a modem which permits dialing into a re-
mote TSU 120 location to configure the unit or read the sta-
tus or performance of the unit.
•
•
Receives traps from any TSU product.
Records and creates display performance data over a 30-
day period.
•
Accesses units via the local area network (TSU 120e only).
To set up the TSU 120 to work with T-WATCH Pro over the
LAN, follow these steps:
Step
1
Action
Set the Unit ID using the front panel. See Unit ID on
page 6-4 for details.
2
3
4
Set ONTROL ORT interface to NORMAL using the
Front Panel
C
P
Configure the
ADDRESS, DEFAULT GATEWAY, and
IP
SUBNET MASK using the front panel.
Follow the installation instructions for T-WATCH Pro
to start the program and connect to the unit.
3-10
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3. Operation
T-WATCH Pro/EIA-232 Connection
direct EIA-232 connection, follow these steps:
Step
1
Action
Set the Unit ID and set a passcode using the front
panel. See Unit ID on page page 6-4 and Set a Passcode
on page 6-4 for details.
2
3
Set the control port rate to the same setting as the PC
Com port.
Connect the PC Com port to the chain-in port on the
TSU 120 using the DB25 adapter and modular cable
provided.
4
Follow the installation instructions for T-WATCH Pro
to start the program and to connect to the unit.
SNMP
The ADTRAN TSU 120 supports the Simple Network Manage-
ment Protocol (SNMP) through the chain-in (SLIP) interface.
The TSU 120e offers a 10BaseT connection which also supports
SNMP. For more information on SNMP see Appendix A, Under-
standing SNMP on page A-1.
To use SNMP via 10BaseT (TSU 120e only), follow these steps:
Step
Action
1
2
Set ONTROL ORT to
.
NORMAL
C
P
Set the
MASK.
ADDRESS, DEFAULT GATEWAY, and SUBNET
IP
3
4
The appropriate MIB browser must be loaded into the
Network Management Station (available on the
ADTRAN webpage at http://www.adtran.com).
The MIB browser issues SNMP gets/sets to the TSU
120e.
61202129L1-1
TSU 120 User Manual
3-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3. Operation
To use SNMP via SLIP port, follow these steps:
Step
Action
1
2
Set ONTROL ORT to
.
C
P
SLIP
Set the
ADDRESS. The DEFAULT GATEWAY, and
IP
SUBNET MASK are not used in SLIP.
3
The appropriate MIB browser must be loaded into the
Network Management Station (available on the
ADTRAN webpage at http://www.adtran.com).
4
The MIB browser issues SNMP gets/sets to the TSU
120e.
Terminal Mode
The TSU 120 provides the front panel menus to a VT 100-type
terminal. This mode can be used to configure and monitor the
unit. Initiate this mode by keying in
on the termi-
<CTRL> PTT
nal once it is connected to the chain-in port. For more informa-
tion on this method of control, see Chapter 8, Telnet/Terminal
Menus on page 8-1.
TELNET
To connect to the TSU 120 via TELNET, follow these steps.
Step
1
Action
Before attempting to connect via TELNET, first define
the IP address, the default gateway, and the subnet
mask using the front panel.
2
3
4
When you begin the TELNET session, you will be
prompted for a password. The default password is
.
ADTRAN
You can change this password using the Management
submenu. See Default Unit Passcode on page 8-7 for
more information.
The TELNET session will time out after a predefined
value that is also set in the Management menu.
Only one TELNET session can be active at one time.
3-12
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Status Menu
Chapter 4
The Status menu branch provides the ability to view the status
of the TSU 120 operation. See Figure 4-1.
%AS
%EF
1) NI PERF RPTS
ES
SES
UAS
2) NI ERRORS
1)STATUS
3) ACTIVE ALARMS
4 )VIEW HISTORY
(ALARM LIST)
END OF LIST
(HISTORY LIST)
END OF HISTORY
1) DTE DATA/CLOCK
5) PORT STATUS
0.1 Nx56/64
2) DTE STATUS
3) PORT RATE
4) DBU DATA/CNTR (TSU 120e)
5) DBU CONTRL (TSU 120e)
6) DBU STATUS (TSU 120e)
6) REMOTE PORT
7) CLEAR PORT ALM
8) ENET STATUS
0.2 DSX-1
DSX-1 ERRORS
(OPTION LIST)
Figure 4-1. Complete Status Menu Tree
Menu flow is normally depicted from left to right. Arrows on
the lower right of the screen indicate the direction of scrolling
to use to view additional menu items. At every level of the
menu, pressing Cancel returns the system to the previous menu
level. Pressing Cancel repeatedly returns the system to the main
menu.
61202129L1-1
TSU 120 User Manual
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4. Status Menu
Network Performance Reports (NI PERF RPTS)
copy of the performance data. The TSU 120 maintains this per-
formance data on the network in compliance with ANSI T1.403
and AT&T document TR54016. The data displayed is data accu-
mulated over the last 15 minutes and over the last 24 hours.
Use the scroll keys to access the complete display of the follow-
ing report fields, as shown in Figure 4-2:
15 Minutes
24 Hours
Data Values
Figure 4-2. Network Interface Performance Report
AS
EF
Percentage of available seconds
Percentage of error-free seconds
%
%
ES
Number of errored seconds (1 or more
errors/second
SES
UAS
Number of severely errored seconds (more
than 320 errors/second)
Number of unavailable seconds (10 or
more consecutive seconds)
If insufficient time has passed to collect data,
displays.
NA
Continue with standard operating procedures to exit the dis-
play.
When this menu is active, performance data can be cleared by
pressing Clear (Shift+9) on the keypad. Only the user copy of
the performance data is cleared.
4-2
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4. Status Menu
Since only the user’s copy of performance data is cleared by the
TSU 120, the data displayed here might be different from the
data sent to the network as PRM data.
Network Interface Errors (NI ERRORS)
The NI ERRORS submenu displays the types of errors the Net-
work Interface (NI) detects. A blinking CSU error LED indi-
cates that network errors are detected.
The asterisk (*) above an item indicates the type of errors
detected. The error types are the following:
CRC
CRC-6 bit errors based on the FDL. This is valid
only in ESF mode.
BPV
Bipolar violations.
Excess zeros.
XS
0
FER
Framing errors.
Active Alarms
This menu item displays a list of current alarms ( LARM IST)
A
L
reported by either the base controller or any of the ports. If no
alarms are current, using this menu item displays
.
End of List
This display includes two lines of text. The top line is the alarm
source. The bottom line is the alarm message. See Figure 4-3 on
page 4-4. A list of alarm messages is found in Appendix C, TSU
120 System Messages on page C-1.
In addition to normal menu operation, you can also access this
menu item with the Alarm function (Shift+8) on the keypad. If
one or more of the Alarm LEDs are illuminated, an alarm is
present. Pressing Cancel returns to the previous menu item.
61202129L1-1
TSU 120 User Manual
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4. Status Menu
Alarm Source
Alarm Message
Figure 4-3. Display of Alarm Message
View History
This menu item both displays and clears the accumulated sta-
tus changes of the unit.
View History displays a history of the first 20 status changes in
the unit, including the date, time, and type of change. The unit
also records for viewing, the date and time an alarm became
active and inactive, as well as the date and time of test activa-
tion and deactivation.
To clear the View History display, press Clear (Shift+9) with the
View History menu active.
Port Status
Port Status displays the signals monitored on the data ports.
For example, the Nx/DBU interface monitors the RTS, CTS,
and RD, along with other signal lines. When a port is selected,
the LCD indicates if the signal is present.
The base Nx interface offers the status screen listed in this sec-
tion. When using other option cards, refer to the appropriate
separate manual for a definition of any status screens offered.
The Port Status of Nx/DBU is examined as an example of how
to use this item. The DBU feature is available only in the
TSU 120e.
4-4
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4. Status Menu
0.1 Nx56/64 Menu Items
DTE Data/Clock
An asterisk (*) indicates an active status of the following lines.
TXD
RXD
Transmit data from the DTE
Receive data toward the DTE
Excess Zeros from the DTE
XS
0
LCK
Lock Status of the phase locked loop
DTE Status
An asterisk (*) indicates an active status of the following lines:
RTS
CTS
DCD
DSR
Request to send from DTE
Clear to send to DTE
Data carrier detect to DTE
Data set ready to DTE
Port Rate
The port rate displays the current setting of the Nx port. Con-
tinue with standard operating procedures to exit the display.
DBU Data/CNTRL (TSU 120e only)
An asterisk (*) indicates an active status on the following lines:
TXD
RXD
DCD
RI
Transmit data to the DCE
Receive data from the DCE
Data carrier detect from the DCE
Ring indicate from the DCE
61202129L1-1
TSU 120 User Manual
4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4. Status Menu
DBU Contrl (TSU 120e only)
RTS
CTS
DTR
DSR
Request to send to DCE
Clear to send from the DCE
Data terminal ready to the DCE
Data set ready from the DCE
DBU Status (TSU 120e only)
DBU SECS
IN DBU
Total seconds in current DBU session
YES/NO indication of active DBU status
0.2 DSX-1 Menu Items
DSX-1 Errors
CRC
An asterisk displays under the CRC if there are
CRC errors in extended superframe format
(ESF) mode. If the DSX-1 plug-on board is
configured for D4 Frame format, the LCD
displays n/a.
BPV
SLIP
An asterisk displays under the BPV if the DSX-1
plug-on board detects bipolar violations.
An asterisk displays under the SLIP if the DSX-1
plug-on board detects frame slips. This is
caused by multiple clock sources in the
application.
FER
An asterisk displays under the FER if the
DSX-1 plug-on board detects frame bit
synchronization errors.
4-6
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4. Status Menu
Remote Port
Remote Port displays the status of activity on the control-in
remote port. This is useful for troubleshooting communication
sessions, and for verifying cabling.
RX
ID
Characters received at remote port
Unit ID received at remote port
CRC Correct CRC received
PC
TX
Correct passcode received
Characters transmitted from the remote port
Clear Port Alarm (Clear Port Alm)
Clears the Link Failed alarms on option modules that have
been removed from the TSU 120 chassis.
ENET Status (TSU 120e only)
TX
Indicates that data is being transmitted from the
10BaseT port.
RX
Indicates that data is being received by the
10BaseT port.
LNK Indicates the current status of the 10BaseT link
integrity test. This should always be on when the
unit is connected to a functional 10BaseT hub.
CPU Active when the CPE is accessing the 10BaseT
interface.
61202129L1-1
TSU 120 User Manual
4-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4. Status Menu
4-8
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5
The ONFIGURATION ENU sets the TSU 120 operational config-
C
M
uration, including all network interface parameters, the alloca-
tion of the DS0s, and the port parameters. See Complete
Configuration Menu on page 5-2.
Menu flow is normally depicted from left to right. Arrows on
the lower right of the screen indicate the direction of scrolling
to view additional menu items. At every level of the menu,
pressing Cancel returns the system to the previous menu level.
Pressing Cancel repeatedly returns the system to the AIN
M
ENU.
M
61202129L1-1
TSU 120 User Manual
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Configuration Menu
1) FORMAT
1) CTL PORT RATE
2) TRAPS
2) CODE
3) YEL ALARM
4) XMIT PRM
5) TIMING MODE
3) ACCESS
4) INIT MODEM
5) CONTROL PORT
6) IP ADDRESS
7) SUBNET MASK
8) DEFAULT ROUTER
9) SLIP RATE
1) NETWORK (NI)
6) SET LBO
7) INBAND LPBCK
8) BIT STUFFING
9) TR-08 OPTIONS
ALARM REPORTS
ALARM FORMATS
BPV THRESHOLD
2) UNIT
A) SLIP FLOW CTL
B) PROXY TRAPS
3) MAP XCHNG
OFF
AUTO
4) MAP IN USE: A(B)
5)DS0 MAP A
1) MAP A @:HH:MM
2) MAP B @:HH:MM
3) CONFIG
1) COPY A > TEMP
2) CREATE TEMP
3) REVIEW MAP A
4) REVIEW TEMP
5) EDIT TEMP
1) DSO RATE
2) TX CLK CNTRL
3) DATA
1) COPY B > TEMP
2) CREATE TEMP
3) REVIEW MAP B
4) REVIEW TEMP
5) EDIT TEMP
6) DS0 MAP B
4) CTS
6) APPLY TEMP > A
5) DCD
6) DSR
6) APPLY TEMP > B
0.1 Nx56/64 Config
7) “0” INHIBIIT
8) INBAND MODE
9) TX CLK SOURCE
7) PORT CONFIG
Nx56/64 (0.1)
THIS SECTION APPLIES ONLY TO THE TSU 120e
1) BACKUP MODE
DBU Config
2) BACKUP ON
02. DSX-1
1) FORMAT
3) PATTRN VERIFY
(OPTION PORTS)
2) CODE
4) BACKUP DELAY
3) YELLOW ALARM
4) LINE LENGTH
5) INBAND LPBACK
6) ROB BIT SIGNL
5) RESTORE DELAY
6) RETRY DELAY
7) NUM RETRIES
8) BACKUP TESTING
9) WKEND LOCKOUT
A) ENABLE HR
1) BACKUP TEST
2) TEST HOUR
3) TEST DAY
B) DSABLE HR
C) TRAP IN DBU
Figure 5-1. Complete Configuration Menu
5-2
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Configuration Menu
NETWORK (NI)
This menu item accesses the configuration of parameters asso-
ciated with the network interface in the base unit. There are
nine submenu items that include setting the format, the line
build out (LBO), and the timing mode. Submenu items do not
include setting the parameters which may be necessary for a
secondary interface (DSX-1 Passthru, etc.).
Network (NI) Menu Items
The menu items are:
Menu Item
FORMAT
Description
Sets the frame format for the NI.
Choices: D4, ESF, and SLC96
D4 is equivalent to superframe format (SF).
CODE
Sets the line code for the NI.
Choices: AMI and B8ZS.
YEL ALARM Enables and disables the transmitting of yellow alarms.
Choices: ENA and DISA.
XMIT PRM
Enables and disables the sending of PRM data on the
collected even if XMIT PRM is disabled (possible only
with ESF Format).
Choices: Off and On.
TIMING
MODE
Selects the clock source for transmission toward the
network from the NI. See TSU 120 Clock Sources on page
5-5 for more information
Choices: Network, DTE (Slot 1), Normal (CSU), U-
BR1TE (Slot 1), Internal, Secondary (SI).
61202129L1-1
TSU 120 User Manual
5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Configuration Menu
Menu Item
Description
SET LBO
Selects the line build out for the network interface. In
AUTO MODE, the TSU 120 sets the LBO based on the
strength of the receive signal and displays the selected
value.
Choices: 0.0 dB, 7.5 dB, 15 dB, 22 dB, Auto.
In order to activate the -36 dB receiver sensitivity, the
LBO should be set to AUTO.
This feature is useful in a point-to-point application
where no network elements are involved. If a network
element such as a Smart Jack is installed on the circuit,
the LBO should be set to 0 dB.
INBAND
LPBCK
Sets unit to accept or reject the network interface loop-
up and loop-down codes as defined in ANSI T1.403.
Choices: Accept, Reject.
BIT
STUFFING
When enabled, bit stuffing causes the TSU 120 to
monitor for ones (1s) density violations and insert a one
(1) when needed to maintain 1s at 12.5 percent.
Choices: Enable, Disable.
TR-08
The TR-08 submenu configures the unit for TR-08
applications. The submenu items and their descriptions
follow.
Alarm Report
Enables and disables the transmitting of alarm reports.
Choices: SEND ALARMS, DISABLE ALARMS
Alarm Format
Sets the alarm frame format to 13 frames or 16 frames.
Choices: ORB-13, ORB-16
BPV Threshold
Sets the threshold for BPVs to trigger an alarm.
Choices: 10-4, 10-5, 10-6
5-4
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Configuration Menu
TSU 120 Clock Sources
The TSU 120 is operable from various clock sources permitting
it to perform properly in many different applications. Set the
network interface clocking options with the clocking options
set by the Network (NI) Configuration menu options.
The following clock source options are available:
•
•
•
•
•
•
•
Network
Base DSX-1 Timing
DTE Timing
Internal Timing
Secondary Timing
Normal (CSU) Timing
U-BR1TE
The selected clock option always designates the clock source for
transmission. Clocking necessary for receiving data is always re-
covered from incoming data.
61202129L1-1
TSU 120 User Manual
5-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Configuration Menu
Network Timed
The network is the source of timing. The received data clocking
is looped back to the network where it is used to determine the
transmission timing. This option is also referred to as loop
timed as the transmission clock is derived from the received
clock. See Figure 5-2.
.
Figure 5-2. Network Timed Clock Source
5-6
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Configuration Menu
Base DSX-1 Timing
The PBX is the source of timing. The TSU 120 uses the clock
derived by the Base DSX-1 interface for transmission timing.
See Figure 5-3.
OSC
T1 XMIT
Network
(DS1)
Interface
(OPTION)
T1 Receive
DSX-1
PBX
Nx56/64
DTE CLOCK
DTE
Figure 5-3. DSX-1 Timed Clock Source
61202129L1-1
TSU 120 User Manual
5-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Configuration Menu
DTE Timing
The DTE is the source of timing. The TSU 120 uses the incom-
ing DTE clock to determine the transmission timing. This is
typically used in applications where it is necessary to have the
DTE as the primary clock source, (such as limited distance line
drivers). See Figure 5-4.
OSC
T1 XMIT
Network
Interface
(DS1)
(OPTION)
T1 Receive
DSX-1
PBX
Nx56/64
DTE CLOCK
DTE
Figure 5-4. DTE Timed Clock Source
5-8
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Configuration Menu
Internal Timing
The TSU 120 is the source of timing. The TSU 120 is configured
to use its own internal oscillator as the source of timing. Appli-
cations include private line driver circuits where one end is set
to network and the other to internal. See Figure 5-5.
OSC
T1 XMIT
Network
Interface
(DS1)
(OPTION)
T1 Receive
DSX-1
PBX
Nx56/64
DTE CLOCK
DTE
Figure 5-5. Internal Clock Source
61202129L1-1
TSU 120 User Manual
5-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Configuration Menu
Secondary Timing
The secondary interface is the source of timing. The TSU 120
uses the clock derived by the secondary interface for transmis-
sion timing and the receive signal timing. See Figure 5-6.
Either a DSX-1 Option Module or a Drop and Insert Option
Module must be installed in the TSU 120 for this mode to func-
tion.
OSC
T1 XMIT
Secondary
Network
Interface
(DS1)
(IO PB)
Interface
(NI)
(SI)
(OPTION)
T1 Receive
PBX
DSX
Nx56/64
DTE CLOCK
PBX
DTE
Figure 5-6. Secondary Timing
5-10
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Configuration Menu
Normal (CSU) Timing
In the Normal (CSU) Timing mode, the Receive Clock is
derived from the Network Interface while the Transmit Clock is
derived from the PBX or other alternative timing source, con-
nected to the Secondary Interface (e.g., Drop and Insert or
DSX-1). See Figure 5-7.
This timing option is the same as that typically used for CSUs.
This is the preferred mode for use with a PBX application.
Secondary
Network
Interface
(SI)
(OPTION)
Interface
(NI)
Figure 5-7. Normal (CSU)
The network interface and secondary interface clocking options
are set by using the Network (NI) Configuration menu options.
Either a DSX-1 Option Module or a Drop and Insert Option
Module must be installed in the TSU 120 for this mode to func-
tion.
U-BR1TE
The U-BR1TE timing selection works like Normal (CSU) except
that timing is derived from the U interface on port 1.1.
61202129L1-1
TSU 120 User Manual
5-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Configuration Menu
Unit Menu
The Unit menu changes the baud rate of the chain in port and
the setup of the dial out port. The menu items are:
Menu Item
Description
CTL PORT
RATE
Sets the baud rate for communication with
the PC or modem.
Choices: 1200, 2400, 9600, 19200, and 38400
kbps
TRAPS
Enables or disables the transmission of trap
messages.
Choices: Enable, Disable
ACCESS
Sets the method of connection from the
TSU 120 to T-WATCH Pro/SNMP
Choices:
Direct - Used if connected directly to the PC.
Dial - Used when connection is through a
modem. The dial string is entered from
T-WATCH Pro/SNMP.
INIT MODEM Allows you to choose an industry standard
or a custom initialization string for a modem
connected to the control port.
Choices: Industry Standard, Custom
Initialization String
CONTROL
PORT
Selects the TCP/IP physical interface;
Normal, using the 10BaseT Ethernet or SLIP
using the EIA-232 serial port (10BaseT is only
available in the TSU 120e).
Choices: Normal, SLIP
If this option is set to SLIP, the EIA-232
port may not be used as a terminal inter-
face.
5-12
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Configuration Menu
Menu Item
Description
IP ADDRESS
This is the IP address that uniquely identifies
the TSU 120 on a TCP/IP network.
This address is composed of four decimal
numbers, each in the range of 0 to 255,
separated by periods. This value is used for
either the 10BaseT Ethernet or SLIP interface,
depending on the IP interface setting
(10BaseT is only available in the TSU 120e).
SUBNET
MASK
This defines which part of a destination IP
address is the Network number. It is used
along with the TSU 120 IP address to
determine which nodes must be reached
through the default IP Gateway. This value is
ignored when the IP interface is set to
.
SLIP
DEFAULT
ROUTER
All IP Packets destined for nodes not on the
TSU 120 unit’s local network are not
forwarded through this IP address.
Normally, this address defines a router
connected to the TSU 120 unit’s local
network. This value is ignored when the IP
interface is set to
.
SLIP
SLIP RATE
This sets the baud rate for the Chain-In port
when used as the SLIP connection for SNMP
management.
Choices: 1200, 2400, 4800, 9600, 19200, 38400
Kbps
SLIP FLOW
CTL
This is used to activate flow control on the
Chain-In port when used as the SLIP
interface. Hardware mode uses RTS and CTS.
Choices: None, Hardware
PROXY TRAPS This determines whether or not traps will be
forwarded from units being “proxied” for.
Choices: Enable, Disable
61202129L1-1
TSU 120 User Manual
5-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Configuration Menu
Map Exchange (Map Xchng)
The AP XCHANGE menu enables and sets the automatic time
M
E
of day map switch. The unit provides selection of the hour,
minute, and seconds for the map switching to take place.
The menu items are:
Menu Item
OFF
Description
Indicates the map in use does not change
(disabled).
AUTO
Indicates that the map in use will change at a
user-selected time of day (enabled).
1. Scroll to select
to enable or
to disable the
OFF
AUTO
Automatic Map Change feature.
2. Press Enter to activate the selection.
3. When is selected, the unit displays the screens to
AUTO
set times for switching.
4. After editing Map A, press Enter to record the Map A
settings and activate the selection fields for Map B.
5. Use the same operation to edit switching time for
Map B.
When ESF is used with an FDL channel between units, the
units automatically coordinate the automatic map switch by
sending a map switch command from end-to-end over the
FDL. Only one end needs to be set to Auto for this to work.
Map In Use: A(B)
The AP IN SE menu item controls the DS0 map the TSU 120
M
U
uses and displays the map in current use.
5-14
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Configuration Menu
DS0 Map A and DS0 Map B
The DS0 maps designate which DS0s are assigned to which
port. See Figure 5-8. There are three maps,
AP
,
DS0 M A DS0
AP , and the EMPORARY EMP MAP.
M
B
T
(T
)
T E M P
M A P A
M A P B
Figure 5-8. DS0 Map Designations
Map A and Map B are the current maps the TSU 120 uses. The
Temp map generates a map before putting it into use.
You can copy Map A to Map B by copying the Map A into the
TEMP map. Then apply (write) the TEMP map into Map B.
The menu items are:
Menu Item
Description
COPY A (B) >TEMP This copies the current map (A or B) into a
Temp Map area. This permits modification
the modifications are completed, the Temp
Map is written to current MAP A B by
( )
selecting
.
Apply
CREATE TEMP
This creates a map by defining a port or Idle
for all DS0s. When CREATE TEMP is first
selected, all DS0s are set to
See DS0 Map
Idle.
Example on page 5-16 for more information.
REVIEW MAP A(B) Permits a quick review of the number of
DS0s assigned to each port and the number
of unassigned DS0s (
) as defined
Idle or TST
in the currently applied Map A(B).
61202129L1-1
TSU 120 User Manual
5-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Configuration Menu
Menu Item
Description
REVIEW TEMP
This menu item is operated the same for the
Temp Map as is REVIEW MAP A or MAP B.
3)
EDIT TEMP
The map in the Temp file can be edited to
whatever configuration is desired. If Map A
had been copied into the Temp file, then after
editing, the Temp file could be applied to
MAP A or MAP B. The menu operation is
identical to
CREATE TEMP with the
2)
exception that the existing port selections
display.
APPLY TEMP> A(B) Writes the Temp map into MAP A.
is
Apply
usually the last step in updating a map and is
accessed automatically at the end of editing
or creating a temporary map. Currently, it
can be bypassed by selecting another menu
choice.
DSO Map Example
A sample selection follows:
DS0: 01 to 24
PORT: IDLE, TST, + option module ports
TST designates which DS0s are used for QRSS testing when
activated under the TEST MENU. When not used for testing, the
TST designation is identical to
.
Idle
5-16
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Configuration Menu
With the cursor on CREATE TEMP, press Enter. The unit displays
the selection screen with the cursor positioned on the first
selection DS0 number. See Figure 5-9.
Select DS0 Number
Select Port
Figure 5-9. Create Temp Selection Screen
1. Use either the Arrow Keys or Numbers to enter the DS0
number (do not mix the use of the keys).
2. Press Enter to complete the selection and move the cur-
sor to Port, the next field.
3. Scroll to select the port which is dependent on the
installed option card.
4. Press Enter to complete the selection and move the
cursor back to the DS0 field.
5. With the cursor on the DS0 field, the DS0 number can
be incremented or decremented by scrolling.
6. Press Copy to place the contents of the last DS0 in the
new DS0 number.
7. When all entries are complete, press Cancel to move
the cursor to the last of the submenu choices, 6 APPLY.
)
8. Either apply the newly created DS0 map or press
ANCEL to return to the DS0 MAP A B submenu
C
( )
choices.
Selecting
will not disrupt the operation of unmodified
Apply
ports.
61202129L1-1
TSU 120 User Manual
5-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Configuration Menu
Port Configuration (Port Config)
Port Configuration selects and configures the parameters asso-
ciated with any data port in the unit. For example, parameters
for the DSX-1 (PBX) interface are set through this menu. The
items that can be set depend on which option module is
installed. The list of option ports will vary with the configura-
tion.
The TSU 120 is designed so that any additional ports devel-
oped in the future will contain the appropriate menu selections
to provide access by use of this menu item.
The Config menus for options ports are described in separate
sections of the manual supplied with the option card.
0.1 Nx56/64 Port Configuration (Port Config) Menu Items
There are two major menu items under Nx/DBU configura-
tion:
X
ONFIG and
ONFIG. Only the TSU 120e
N 56/64 C
DBU C
offers the DBU feature.
Nx56/64 Menu Items
Menu Item
Description
DS0 RATE
This sets the base rate of the interface. The
actual data rate depends on the number of
DS0s assigned to the Nx port.
Choices: 56K, 64K
TX CLK CNTRL
Controls the clock used by the TSU 120 to
accept transmit (TX) data from the DTE. The
default is normal. If the interface cable is
long, causing a phase shift in the data, the
clock can be selected as Invert. This switches
the phase of the clock which should
compensate for a long cable.
Choices: Normal, Invert
5-18
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Configuration Menu
Menu Item
DATA
Description
Used to control the inverting of the DTE
data. This inversion can be useful when
operating with an HDLC protocol. Often
used as a means to ensure 1s density.
Choices: Normal, Invert
should also be selected to prevent an
open DTE input from placing zeros on
the network.
CTS
Used to control characteristics of CTS.
Choices: Normal*, Force On
*See Table 5-1 on page 5-20.
DCD
Data Carrier Detect. Indicates to the DTE
when a valid signal is being received at the
Network Interface.
Choices: Normal*, Force On
*See Table 5-1 on page 5-20.
DSR
Data Set Ready. This signal indicates to the
DTE when the DCE is turned on and ready
for operations.
Choices: Normal*, Force On
*See Table 5-1 on page 5-20.
0 INHIB
The Nx interface will detect an uninterrupted
string of zeros (0s) being transmitted toward
the network. If 0s are transmitted for >1
second, the TSU 120 will force 1s.
Choices: On, Off
61202129L1-1
TSU 120 User Manual
5-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Configuration Menu
Menu Item
Description
INBAND MODE
The Nx56/64 port is capable of providing an
inband communications channel (for T-
Watch and SNMP) between units. This is
accomplished by using 8 kbps of the first DS0
assigned to that particular Nx56/64 port. If
in 56 K mode, no data bandwidth will be
used. Inband must also be enabled at the
destination port.
Choices: On, Off, On Demand
TX CLK SOURCE
This controls the source of the clock used by
the TSU 120 to accept transmit data from the
DTE. The default is INTERNAL. If the
application requires that the DTE device
provides the clock with the transmit data, the
EXTERNAL setting is used.
Choices: Internal, External
Table 5-1. Normal Mode of Operation
Signal
RTS
V.54 Loop- 511 TST
back ON
Follows OFF OFF
Self Test NetwkTest
Active Active
No DS0
Mapped
OFF
Network
Alarm
CTS
DCD
DSR
OFF
OFF
OFF
OFF
—
OFF
—
—
—
—
OFF
OFF
OFF
—
OFF
OFF
OFF
Where “—” = don’t care
*Until backup becomes active
5-20
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Configuration Menu
DBU Configuration Menu Items (TSU 120e only)
Menu Items
Description
BACKUP MODE In a backup condition, both ends of the circuit must
detect backup conditions before backup is acti-
vated. One DBU is set to ORIGINATE and the other to
ANSWER Upon a network failure, only the Origi-
.
nate DBU initiates backup by dialing the Answer
end. Once called, the
goes into backup
Answer DBU
mode only if a backup condition is detected. This is
ideal for controlling where calls originate.
Choices: Disable, Originate, Answer
BACKUP ON
Selects the conditions that cause the Nx/DBU to
initiate Backup.
NET FAIL:
Backup occurs on RED ALARM, YELLOW ALARM, BLUE
ALARM, and LOS.
NET DATA FAIL:
/
Backup occurs on the same conditions as NET FAIL
,
plus loss of data transitions on the data the Nx56/
64 receives from the network.
PATTRN VERIFY Selects whether or not the DBU will use its pattern
generator and receiver to authenticate backup
attempts. When the local and remote units are both
Nx/DBUs, set to ENABLE; otherwise set to DISABLE.
Choices: Enable, Disable
BACKUP DELAY Selects the time allowed to elapse between the net-
work going into alarm or no data transmissions
and the backup beginning.
Choices: 1 sec, 3 sec, 10 sec, 30 sec, 1 min, 5 min,
10 min
61202129L1-1
TSU 120 User Manual
5-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Configuration Menu
Menu Items
Description
RESTORE DELAY Selects the time that elapses between the network
going out of alarm or data and the backup call
being taken down. If NEVER is selected, the user
must deactivate the backup mode.
Choices: 1 sec, 3 sec, 10 sec, 30 sec, 1 min, 5 min,
10 min, never
RETRY DELAY
NUM RETRIES
Selects the time between redialing the external
DCE after failed dial attempts.
Choices: 10 sec, 30 sec, 1 min, 5 min, 10 min
Selects the number of times the DBU will attempt
to redial if unable to connect.
Choices: None, unlimited, 3 times, 10 times.
BACKUP
TESTING
Selects the options for the automatic ISDN verifica-
tion feature of the Nx/DBU. Verification of the
backup circuit does not disrupt data on the T1.
ACKUP EST:
B
T
Selects the frequency of automatic backup circuit
verification by the DBU.
Choices: Manual, Hourly, Daily, Weekly
EST OUR:
T
H
Selects the hour of the day the Backup test will
occur.
Choices: 0-23
EST AY:
T
D
If Weekly Backup test is selected, selects which day
to perform the test.
Choices: Monday - Sunday
WKEND
LOCKOUT
If no backup is desired from midnight Friday to
midnight Sunday, set this selection to ON; other-
wise set to OFF.
Choices: On, Off
5-22
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Configuration Menu
Menu Items
Description
ENABLE HR
The hour backup will be enabled. Enter from the
numeric keyboard.
Choices: 0-23
DISABLE HR
The hour that the backup will be disabled. Enter
from the numeric keyboard.
Choices: 0-23
For these items to function properly, verify that
the time and date in the TSU are set correctly.
See Chapter 6, Utility Menu, Time/Date
section.
TRAP IN DBU
If traps are enabled , this parameter will send either
a single trap upon going into a DBU session or
send repeated traps for the duration of the DBU
session.
Choices: Single, Repeated
0.2 DSX-1 Port Configuration (Port Config) Menu Items
The menu items are:
Menu Items
FORMAT
Description
ORMAT sets the frame format for the base DSX-1
F
interface.
Choices: D4, ESF
CODE
ODE sets the line code for the base DSX-1
C
interface.
Choices: AMI, B8ZS
YELLOW ALARM
YEL ALARM enables and disables the transmitting of
yellow alarms.
Choices: Enable, Disable
61202129L1-1
TSU 120 User Manual
5-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Configuration Menu
Menu Items
Description
LINE LENGTH (FT)
INE ENGTH provides selection of the proper
L
L
output level for the base DSX-1 based on the length
of the interface cable.
Choices: 1-133 ft, 133-266 ft, 266-399 ft, 399-533 ft,
533-655 ft, -7dB
IN-BAND
N BAND OOPBACK sets the base DSX-1 to accept or
I -
L
LOOPBACK
reject in-band loopup or loopdown codes (per
(INBAND LPBACK) ANSI T1.403 specification) which may be sent to
the card over the DSX-1 interface. This loopback is
a line loopback.
Choices: Accept, Reject
ROBBED BIT
SIGNALING
(ROB BIT SIGNL)
This menu option is used to enable/disable
robbed-bit signaling. Whenever the base DSX-1
interface is connected to terminal equipment (i.e.,
PBX/SW56) for voice or dialed data services, this
option should be enabled. The only exception is
when the terminal equipment is using a form of
common channel signaling (i.e., PRI). For
applications requiring robbed-bit signalling as well
as a messaging channel (i.e., some proprietary PBX
channels), the
selection is provided.
ON:DSOs 1-23
Choices: OFF, ON: ALL DSOs, ON: DSOs 1-23
5-24
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Utility Menu
Chapter 6
The UTILITY MENU tree displays and sets system parameters (see
Figure 6-1 on page 6-2). This includes:
•
setting the time and date,
•
•
resetting all parameters to factory values, or
re-initiating the unit.
This menu also displays the unit software revision and the Unit
ID setting.
Menu flow is normally depicted from left to right. Arrows on
the lower right of the screen indicate the scrolling direction to
view additional menu items. At every level of the menu, press
Cancel to return the system to the previous menu level. Press-
ing Cancel repeatedly returns the system to the MAIN MENU.
61202129L1-1
TSU 120 User Manual
6-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6. Utility Menu
TIME: HH:MM:SS
DATE: MM/DD/YY
1) TIME/DATE
(Returns all
configurations
2) FACT RESTORE
to factory settings)
3) SET PASSCODE
4) UNIT ID
NEW PASSCODE
3) UTIL
VERIFY PASSCODE
5) SOFTWARE REV
(Displays Current
Software Revision
6) PORT UTILITY
7) ENET ADDRESS
8) SERIAL NUMBER
9) CMD MODE
0.1 Nx56/64
0.2 DSX-1
(OPTION PORTS)
Figure 6-1. Complete Utility Menu Tree
6-2
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6. Utility Menu
Time/Date
This menu option displays or edits the current time and date.
The TSU 120 maintains the time and date during power-off
conditions.
If you want to...
Do this...
Record the entry and move to Press Enter after any numeric change
the next editing position
Move to a different field to edit Press Enter at the editing position
without making any changes, or
Use the Up and Down Arrow keys
End the editing process
Press Cancel
Factory Restore (Fact Restore)
This menu item restores the factory default settings for all unit
parameters, including configured DS0 maps.
Set Passcode
Enter Passcode from Other Menus
The Passcode prompt may make an unexpected appearance
from other menu operations. This happens only when the unit
is operating in the limited access mode, i.e., without an active
passcode. The limited access mode may become active even if a
passcode was entered as it does when there is no activity for
ten minutes.
If the unit is to be remotely accessed using T-WATCH Pro, a
passcode must be entered. When managing a number of units,
the passcode can be the same for all.
The unexpected appearance of the Passcode prompt occurs, for
example, while operating in a limited access mode and
attempting to change the Data Rate, (2)CONFIG, 2)UNIT, 1)CTL PORT
RATE, 1)DATA RATE. Use the Number Keys to enter the correct
passcode and press Enter. The unit displays
.
ACCESS GRANTED
61202129L1-1
TSU 120 User Manual
6-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6. Utility Menu
Pressing any key after entering a passcode causes the unit to
return to the previous active menu. In this case it returns to
2)CONFIG, 2)UNIT, 1)CTL PORT RATE, to permit changing the data
rate.
Change/Set a Passcode
The passcode can be changed or set at any time or eliminated
altogether through the Utility Menu item 3)SET PASSCODE. This
procedure requires the current passcode (if one is established)
for operation.
The passcode can only be entered by using numbers. After
entering the desired passcode, press Enter.
Set a null passcode at the 3)SET PASSCODE menu by pressing
Enter without any numbers. This sets a null passcode and
grants unlimited access.
Passcode Automatic Time-out
For added security protection the unit is equipped with an
automatic time-out for operation with the password. After ten
minutes of inactivity, the unit reverts to limited access opera-
tion. To make changes in the configuration, the passcode can be
reentered.
If the passcode number is lost, contact ADTRAN Customer Ser-
vice for assistance.
No Passcode Desired
At the NEW PASSCODE prompt (in the Set Passcode menu), press
Enter without any numerical entry. The system nullifies the
need to enter a password for subsequent use and proceeds to
the UNIT ID prompt.
Unit ID
This menu is used to access the current Unit ID setting. View-
ing is available in limited-access mode. Editing or changing the
Unit ID requires the use of a password, as in editing mode. Unit
identification numbers must be between 2 and 999.
6-4
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6. Utility Menu
If an out-of-range number is entered, the unit assumes the
upper limit number of 999.
Set the Unit Identification
In the UNIT ID MENU (item 4) under the UTIL MENU, enter any
value between 2 and 999. The number 1 is reserved for the PC.
Press Enter to record the Unit ID number and to establish its
availability for operation by remote control. The unit proceeds
to the SET CONTROL PORT prompt.
No Unit ID Desired
Press Enter at the UNIT ID PROMPT without entering any numbers.
The unit will not be able to be operated by remote control.
Software Revision (Software Rev)
This menu provides access to the display of the current soft-
ware revision level loaded into the base unit controller. This
information is required when requesting assistance from
ADTRAN Customer Service or when updates are needed.
Press Cancel to exit.
Port Utility (Option Ports)
This menu provides access to the display of the current soft-
ware information for each port installed in the unit. This infor-
mation is required when requesting assistance from ADTRAN
customer service or when updates are needed.
ENET Address (TSU 120e only)
Displays the Ethernet address for the 10BaseT port.
Serial Number
Displays the serial number of the unit.
CMD Mode
Reserved for factory use.
61202129L1-1
TSU 120 User Manual
6-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6. Utility Menu
6-6
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7
The EST ENU initiates different types of unit tests and dis-
T
M
plays test results in the LCD window. The EST MENU contains
T
four items (see Figure 7-1 on page 7-2).
Executing tests will disrupt some of the normal operation. See
individual menu items concerning tests before executing.
Menu flow is normally depicted from left to right. Arrows on
the lower right of the screen indicate the scrolling direction to
view additional menu items. At every level of the menu, press-
ing Cancel returns the system to the previous menu level.
Pressing Cancel repeatedly returns the system to the
AIN ENU.
M
M
61202129L1-1
TSU 120 User Manual
7-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7. Test Menu
LINE ON
1) LOCAL LOOPBCK
2) REMOTE LOOPBK
PAYLOAD ON
NO LOOPBACK
ATT INBAND LLB
ANSI FDL LLB
ANSI FDL PLB
FT1 LPBK
1) NETWORK TESTS
NO LOOPBACK
ALL ZEROS
QRSS ALL DS0S
QRSS TST DS0S
ALL ONES
5) TEST
3) TEST PATTERN
NONE
4) PATTERN RESULT
(Displays results)
Nx56/64 ( 0.1)
(Displays results)
2) RUN SELFTEST
3) PORT TEST
1) DTE LOOPBACK
2) 511 PATTRN
3) 511 RESULTS
(displays results)
4) DBU LOOPBACK
5) DBU TEST
TESTS OFF
4) CANCEL TESTS
INTERFACE TST
FORCE BACKUP
6) DBU DATA /CNTRL
7) DBU TST RESULT
(displays results)
(displays results)
This section applies to the TSU 120e only
0.2 DSX-1
1) LOOPBACK
(OPTION PORTS)
Figure 7-1. Complete Test Menu Tree
7-2
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7. Test Menu
Network Tests
Network tests control the activation of loopbacks and the initia-
tion of data test patterns.
Network tests are run on the Network Interface (NI). You can
select three different test configurations to determine the type
of loopback and the pattern to run. Test results display in the
LCD window.
Executing ETWORK ESTS will disrupt normal data flow
N
T
unless only TST DS0S are selected for testing.
Loopback Tests
A number of different loopbacks can be invoked locally from
the front panel, by T-Watch commands, or remotely by using
special in-band codes (AT&T D4 network loop-up and loop-
down codes). Additionally, the loopbacks can be remotely con-
trolled by means of out-of-band commands by the T1 ESF FDL
or from T-WATCH Pro by a modem connection.
Network Interface Loopbacks
Network interface loopbacks (see Figure 7-2 on page 7-4) affect
the entire T1 data stream. There are two types of network loop-
backs, LINE LOOPBACK and PAYLOAD LOOPBACK.
Line Loopback
Line loopback loops all of the received data back toward the
network. The transmitted data is the identical line code that
was received, including any bipolar violations or framing
errors.
Payload Loopback
Payload loopback is similar to line loopback, except that the
framing is extracted from the received data and then regener-
ated for the transmitted data.
61202129L1-1
TSU 120 User Manual
7-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7. Test Menu
TSU 120
NI CSU
Secondary
Interface
DS1
Payload Loopback
Line Loopback
Figure 7-2. Network Loopback Tests
LOCAL LOOPBCK
There are three available choices for setting the local loopback:
LINE ON
Activates the line loopback
PAYLOAD ON
Activates the payload loopback
NO LOOPBACK Deactivates the loopback
Using the arrow keys, select a setting and record it by pressing
Enter. The unit returns the display of 1) LOCAL LOOPBCK and
2)REMOTE LOOPBCK
REMOTE LOOPBK
This activates the same loopbacks as Local Loopback but at the
far end. It uses either the inband loop-up code as specified by
ANSI T1.403 for line loopback (ATT In-Band LLB), or the FDL
as specified in ANSI T1.403 for payload and line loopback
codes. The following options are available:
ATT IN BAND LLB
Activates the line loopback using
inband code
-
ANSI FDL PLB
ANSI FDL LLB
Initiates the transmission of an FDL
payload loopup code toward the far
end
Initiates the transmission of an FDL
line loopup code toward the far end
7-4
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7. Test Menu
FT1 LPBK
Initiates the transmission of a FT1
loopback using the inband code
described in T1.403.
NO LOOPBACK
Deactivates the loopback
Remote Loopback can only be used with Fractional T1 if the ANSI
FT1 LLB is selected.
After a Remote Loopback option is selected, the TSU 120 veri-
fies that the far end is actually in a loopback by checking for the
receipt of a code looped back from the far end. Once the
Remote Loopback type is selected, the LCD displays the loop-
back progress by displaying LOOPING until loopback is verified.
Test Patterns
All Zeros
Sends an all zeros pattern to the network.
All Ones
Sends an all ones pattern to the network.
QRSS Pattern
The QRSS pattern is commonly used to simulate real data in T1
interfaces. This pattern can be assigned to appear in all DS0s or
only in TST DS0s. When QRSS is set in all DS0s and one of the
network loopbacks previously described is activated at the far
end, a total end-to-end integrity check can be run without the
need for any external test equipment. When QRSS is assigned
to TST DS0s, an integrity check of the link can be run along
with normal data flow. The TST DS0s are user-assigned as part
of the DS0 Map. This sets the pattern for the test and initiates
the transmission of the pattern. The test is terminated by select-
ing NONE. The following patterns are available:
61202129L1-1
TSU 120 User Manual
7-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7. Test Menu
QRSS ALL DS S
Generates a QRSS test pattern and
inserts the pattern into all DS0s
0
QRSS TST DS S
Inserts a QRSS pattern in those DS0s
mapped as TST in the currently active
map (A or B)
0
NONE
Terminates pattern generation
QRSS always runs at 64K/DS0.
Example
1. Select QRSS ALL DS0S by using the Arrow Keys.
2. Press Enter to record the selection. The TSU 120 starts to gen-
erate a QRSS test pattern and inserts the pattern into all
DS0s.
3. To end the test, select
.
NONE
PATTERN RESULT
Displays the results of the test currently active. Leaving and
returning to this menu item does not interrupt the test.
Pressing injects errors into the test pattern. These errors are
2
detected by the device performing the pattern check.
ES
The number of seconds with at least 1 bit error.
BES
The number of seconds with more than 1 bit error
and less than 320.
SES
The number of seconds with more than 320 bit
errors.
SYNC
Indicates if pattern sync is (yes) or is not (no) valid.
An asterisk (*) indicates if pattern sync has been lost
since the start of testing.
7-6
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7. Test Menu
Press Shift+9 to clear results. The results are accumulated until
the test pattern is set to NONE or
.
CLEARED
Using TST DS0s for testing can be very useful, particularly in
Fractional T1 applications. You can run an end-to-end test on
the Fractional DS0s by:
1. Setting for Map B the TST in the same DS0 as used by Map
A to receive data from an Nx/DBU port, and
2. Looping the far end using a V.54 loopback code on the Nx/
DBU port (DBU is TSU 120e only).
In addition, a single DS0 can be used for continuous testing
while other DS0s are passing normal data. This will also pro-
vide an end-to-end check on the entire link. Set each end to
send QRSS in TST DS0s (using 1 DS0) and occasionally view
the results on the PATTERN RESULT menu selection.
Run Self-test
The self-test checks the integrity of the internal operation of the
electronic components by performing memory tests and by
sending and verifying data test patterns through all internal
interfaces. Although actual user data cannot be passed during
these tests, the self-test can be run with the network and DTE
interfaces in place and will not disturb any external interface.
The memory portion of the self-test automatically executes
upon power-up. A full self-test can be commanded from a front
panel menu or from T-WATCH Pro.
In addition to the specified self-tests, background tests are also
run on various parts of the internal electronics. These run dur-
ing normal operation to confirm continued correct functioning.
This menu selection is used to execute a full internal self-test.
The results of the self-tests are displayed in the LCD. Upon
invoking the command, the LCD displays
SYSTEM SELF-TEST
and the test LEDs are illuminated. Test failures are displayed in
the LCD window.
61202129L1-1
TSU 120 User Manual
7-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7. Test Menu
The self-test consists of the following tests:
OARD EVEL ESTS Each of the TSU 120 boards contain an
B
L
T
on-board processor which executes a
series of tests checking the circuitry
on the board.
•
•
•
RAM tests; EPROM checksum
DS0 map tests
On-board data path; sending a
known test pattern through an on-
board loop
NIT EVEL ESTS
•
•
•
Front panel LED verification
Phase Lock Loop verify
U
L
T
Board-to-board interface test
A test pattern is sent from the controller through a loopback on
all other boards and is checked on the controller. This verifies
the data path, clocks, and control signals.
If a failure is detected, note the failure number and contact
ADTRAN Technical Support.
Executing the self-test will disrupt normal data flow and prevent
remote communication until it is complete.
Port Tests
The Port Tests menu is used to activate testing of specific data
ports. It controls the activation of loopbacks and the initiation
of data test patterns. Test results are displayed in the LCD win-
dow.
Port tests execution will disrupt normal data flow in the port be-
ing tested.
7-8
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7. Test Menu
Port Test Menu Items for 0.1 Nx56/64
0.1 Nx56/64 is the base Nx interface. It offers the following test
functions:
DTE LOOPBK
This initiates a loopback. The following options are available:
PRT LCL
The Nx port activates both a Local
loopback (back toward the DTE) and a Port
loopback when either is invoked.
/
REMOTE
OFF
The remote loopback causes a V.54 code to
be sent to the far end. The Nx at the far end
activates a PORT/LCL loopback upon
detection of the V.54 code.
The loop is deactivated.
The TSU 120 checks the remote loopback activation by detecting
a proper response from the remote end. While waiting for the re-
sponse, the display shows Looping. If successful, the display
changes to LOOPED-UP. If unsuccessful, the display shows
.
FAILED
511 PATTERN
This activates the generation of the 511 test pattern. The follow-
ing options are available:
ON
The pattern check circuitry is enabled and a
test started. The test is ended by selecting
.
OFF
OFF
The pattern generation and check is
disabled.
511 RESULTS
This displays the results of the 511 test indicated in the 511
option. The results are in the form of the number of errored sec-
onds. The error count can be cleared by pressing Clear (Shift+9).
61202129L1-1
TSU 120 User Manual
7-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7. Test Menu
DBU Loopback (TSU 120e only)
ON
Initiates a loopback from the DBU towards the
external DCE
OFF
Terminates the loopback test
DBU Test (TSU 120e only)
This selection is used to force a backup to occur even if a
backup condition does not exist.
Test Name
What it does...
Turns off DBU tests
TEST OFF
FORCED
BACKUP
Forces a backup regardless of time-of-day
lockouts or network conditions
INTERFACE
TEST
Causes the external DCE to dial its stored
number. After the connection is established,
the DBU sends a test pattern to verify the
backup network. This test does not disrupt
data or the primary network.
DBU DATA/CNTRL (TSU 120e only)
Allows status of DCD and RI to be monitored while the
INTERFACE TST is on. If the dial-up network is correctly config-
ured and dialed up, there should be an asterisk (*) over DCD.
DBU TST RESULT (TSU 120e only)
When an interface test is active, this screen will show the total
number of DATA BLOCKS received and the number of blocks
with errors.
Port Test Menu Items for 0.2 DSX-1
Loopback
Loopback activates the loopback function on the base DSX-1
interface. The available loopbacks are Port Loopback (towards
the NI) and Line Loopback (towards the PBX or other terminal
equipment).
Cancel Tests
Use this menu selection to deactivate all active tests, including
tests on option modules.
7-10
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Telnet/Terminal Menus
Chapter 8
MAIN MENU
The
ERMINAL AIN MENU is the first menu displayed
TELNET/T
M
after the TELNET/Terminal session is established.
See Figure 8-1. The default TELNET/Terminal password is
ADTRAN.
Only one TELNET/Terminal session may be active at a time.
ADTRAN - TSU 120
Password: XXXXXXXX
Main Menu
1) Status
2) Config
3) Util
4) Test
5) Remote Menu Access
6) Management Config
7) Flash Download
8) Quit Session
Figure 8-1. Telnet/Terminal Main Menu
61202129L1-1
TSU 120 User Manual
8-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8. Telnet/Terminal Menus
tion on the available menu options, refer to the following sec-
tions:
•
•
•
•
Status Menu on page 4-1
Configuration Menu on page 5-1
Utility Menu on page 6-1
Test Menu on page 7-1
DS0 Maps Configuration Menu
The Telnet/Terminal version of the DS0 maps configuration
menu takes advantage of the 24-line VT 100 display. Upon
entering this menu, the current Temp (temporary) map dis-
plays and is followed by nine selections that you can use for
configuring and reviewing map information. See Figure 8-2
TEMP MAP
DS0# PORT
DS0#
PORT
1
2
3
4
5
6
7
8
13
14
15
16
17
18
19
20
21
22
23
24
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
9
10
11
12
1) COPY MAP A TO TEMP MAP
2) COPY MAP B TO TEMP MAP
3) CREATE TEMP MAP
4) REVIEWMAP A
5) REVIEW MAP B
6) REVIEW TEMP MAP
7) EDIT TEMP MAP
8) APPLY TEMP MAP TO MAP A
9) APPLY TEMP MAP TO MAP B
Figure 8-2. DS0 Temp Map
8-2
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8. Telnet/Terminal Menus
You can use the RROW EYS or Number Keys to move the cur-
A
K
sor from one selection to another. Use the Enter Key to perform
the action displayed in the LCD to the right of the cursor.
Map Configuration
Map configuration consists of the following steps:
Step
1
Action
Initialize the Temp Map to one of three
configurations:
• Current Map A
• Current Map B
• All Idles
This step is optional.
2
3
Edit the Temp Map so that it reflects the desired
map configuration.
Replace the current DS0 Map A or Map B
configuration with the Temp Map configuration.
Initializing the Temp Map
Upon entering the DS0 maps configuration menu, the Temp
map reflects its last configured state.
If you want to...
Use these selections...
initialize the displayed Temp Map to
one of three configurations.
1 - 3
1 , 2
initialize the Temp Map from its
current configuration to one which
reflects the currently stored Map A or
B configurations, respectively.
3
initialize the Temp Map to an all
IDLE state.
61202129L1-1
TSU 120 User Manual
8-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8. Telnet/Terminal Menus
Editing the Temp Map
To edit the Temp Map, follow these steps.
Step
1
Action
To make additional changes to the Temp Map, use
7 to enter the Temp Map edit mode.
Selection
Explanation:
Upon entering this mode, the cursor location moves to DS0
number one in the DS0 field of the Temp Map. The cursor
may be moved from one DS0 to another using the Arrow
Keys until it is located at the DS0 number whose assigned
port needs to be changed.
2
3
Press the Enter Key to move the cursor to the Port field
Use the Arrow Keys to scroll through the possible port
selections.
4
5
Press the Esc Key to restore the previous port assignment
and return to the DS0 field.
Press the Enter Key to save the current selected port and
return to the DS0 field.
Explanation:
Once the cursor is again located in the Temp Map DS0 field,
pressing the Esc Key a second time, causes the cursor to
return to
below the Temp Map display.
Selection 1
Applying the Temp Map
Once the Temp map reflects the desired configuration, use
or to apply this configuration to Map A or B,
Selections 8
9
respectively.
Reviewing Maps
through give a summary of the number of ports
Selections 4
6
assigned to Map A, Map B, and the Temp Map, respectively.
8-4
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8. Telnet/Terminal Menus
Remote Menu Access
This displays TELNET menus for a remote device (may be
another TSU/TDU or any other ADTRAN product that sup-
ports TELNET via its EIA-232 chain port). After selecting this
option, the user may:
1. Choose to connect to a device entered in the Unit Access
Table or
2. Enter a Unit ID for a unit not listed in the Unit Access
Table. CTRL + X terminates the session and returns to the
TSU 120 Main menu.
Management Configuration
This menu sets management information, such as SNMP com-
Unit Access Table
This menu creates and edits the Unit Access Table. This table
stores the Unit ID, Passcode, and Unit Type for units connected
via chain ports or connected remotely to the TSU/TDU (see
Unit Access Table on page 8-6). An entry in the table is required
only to support proxy SNMP MIB access or polling. For MIB
access, an entry is required only if the unit's passcode is not the
same as the Default Unit Passcode, or the unit is a single port
TSU standalone.
It is not necessary to have an entry in this table for a remote unit
in order to TELNET to it or forward SNMP traps from it. In the
TELNET case, the Remote Menu Access menu is selected from the
Main Menu and a Unit ID is entered which may or may not be in
the Unit Access Table.
Units accessed via T-WATCH Pro over TCP/IP use the Unit ID
and passcode set by T-WATCH Pro running on the PC.
61202129L1-1
TSU 120 User Manual
8-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8. Telnet/Terminal Menus
_____________________________Unit Access ____________________________
Unit ID
Passcode
DEFAULT
0033
Type
Polled
No
PollStatus
UP
20
3
Standard
Standard
Yes
6
0095
TSU Stand Alone No
8
0022
Standard
Yes
UP
1) Add New Unit
2) Modify Unit
3) Delete Unit
4) Default Unit Passcode
5) OK
0022
Figure 8-3. Unit Access Table
Add New Unit
This adds a new device to the unit access table.
•
•
You must enter a device NIT
,
ASSCODE, NIT YPE, and
U
ID P
U
T
OLLED LAG.
P
F
Unit type can be TANDARD (which supports any TSU/TDU
S
Multiplexer and the ISU 512) or
TANDALONE (a single
TSU S
port TSU with no option card slot).
You may select a passcode of to
•
•
for each device or
9999
0
DEFAULT. This results in the default passcode being used
(defined as 0022 in Figure 8-3).
Traps are normally sent from the unit in alarm to the TSU
120. For units in the Unit Access Table that are not chained
directly to the TSU 120 but are managed over Inband or the
FDL, traps are not automatically forwarded.
•
Polling must be enabled on the TSU 120 for these units in or-
der to receive Traps on the NMS. The TSU 120 can be con-
figured to poll selected units for traps by enabling the
polled option when adding or modifying a unit entry.
8-6
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8. Telnet/Terminal Menus
Modify Unit
Allows NIT
,
ASSCODE, EVICE YPE, and OLLED LAG to
U
ID P
D
T
P
F
be changed for an existing entry in the table.
Delete Unit
Deletes an entry in the table.
Default Unit Passcode
Sets the default passcode for all devices in the table that have
passcodes set to DEFAULT, or for any unit not listed in the table.
OK
Returns to the Configure Agent menu.
SNMP Read Community
SNMP Read Community Name defaults to
•
.
public
•
•
•
NMSs using this community name have read access for all
supported MIB objects, but do not have the ability to change
MIB objects.
This value must be set to the same value on both the TSU
120 and the NMS (OpenView®, etc.) in order for the NMS
to have read access to MIBs supported by the TSU 120.
This value must be a text string of 16 characters or less.
SNMP Read/Write Community
•
•
•
SNMP NMS using this community name have full read/
write access to all supported MIB objects (defaults to pri-
vate).
This setting must be the same value on both the TSU 120
and the NMS in order for the NMS to have read/write ac-
cess to MIBS supported by the TSU 120.
This value must be a text string that is 16 characters or less.
61202129L1-1
TSU 120 User Manual
8-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8. Telnet/Terminal Menus
To access other units external to the TSU 120 (proxied units) us-
ing an SNMP MIB browser, append a period and the Unit ID of
the external device to the read only and read/write community
name used in the MIB Browser; for example, public.4. See Appen-
dix A, Understanding SNMP for more information.
SNMP Trap Community
This community name is used for all SNMP traps forwarded by
the TSU 120. Traps received from daisy-chained units have a
period and the Unit ID appended to the trap community name.
Host 1 Trap IP Address
The first of four entries for SNMP trap destination addresses.
The TSU 120 forwards all SNMP traps to the IP address speci-
fied in this entry. If the address is set to the default value of
0.0.0.0, no traps are forwarded for this particular value.
Host 2 Trap IP Address
Defaults to 0.0.0.0. Second destination address for SNMP traps.
Host 3 Trap IP Address
Defaults to 0.0.0.0. Third destination address for SNMP traps.
Host 4 Trap IP Address
Defaults to 0.0.0.0. Fourth destination address for SNMP traps.
System Name
A text string that can uniquely identify an SNMP-managed
node.
System Contact
A text string containing the name, phone number, etc. of the
individual responsible for maintaining an SNMP-managed
node.
8-8
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8. Telnet/Terminal Menus
System Location
A text string describing the physical location of an SNMP man-
aged node (for example,
).
SECOND FLOOR PBX ROOM
Auth. Fail Traps Sent
(
: defaults to
)
DISABLED
DISABLED, ENABLED
When enabled, the TSU 120 issues an SNMP trap when any
SNMP request is received with an invalid community name.
Can be used for security purposes.
Poll Link Status Traps Sent
(
,
, defaults to
). When enabled,
DISABLED
DISABLED ENABLED
the TSU 120 sends an SNMP trap whenever a device config-
ured to be polled fails to respond. When the device begins
responding to polls, a poll link-up trap is sent. The format of
the traps are defined in the agent MIB.
Ping IP Host
Allows the user to Ping a specific IP address.
Telnet/Terminal Timeout
The TSU 120 terminates a TELNET or Terminal session if no
activity is detected for this length of time. Only one TELNET or
Terminal session may be active at one time. This timeout pre-
vents an unattended session from blocking interactive access to
the agent. The default value is five minutes.
Telnet/Terminal Password
This option allows modification of the password required for
entry into a TELNET or Terminal session. The default value is
ADTRAN.
Exit
Returns to the TSU 120 Main menu.
61202129L1-1
TSU 120 User Manual
8-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8. Telnet/Terminal Menus
Flash Download
The TSU 120 uses flash memory that allows software updates
via the EIA-232 port. This menu selection allows you to manu-
ally perform a flash download using
.
is
XMODEM T-FLASH
also available to automate this process.
Quit Session
Terminates the TELNET/Terminal session.
8-10
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Understanding SNMP
Appendix A
ABOUT SNMP
As local area network (LAN) environments became standard-
ized over the past ten years, multi-vendor equipment grew
with competition. It became necessary to manage the various
vendor equipment from a single control console. Thus, the
SNMP emerged as the standard for managing commercial
TCP/IP networks.
The term
broadly refers to the message protocols used to
SNMP
exchange information between the network and the managed
devices, as well as to the structure of network management
databases.
Basic Components
SNMP has three basic components:
,
,
Network Manager Agent
and
.
MIB
Network Manager
This is a control program that collects, controls, and presents
data pertinent to the operation of the network devices. It
resides on a network management station.
Agent
This is a control program that responds to queries and com-
mands from the network manager and returns requested infor-
mation or invokes configuration changes initiated by the
manager. It resides in each network device.
61202052L1-1
TSU 120 User Manual
A-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A. Understanding SNMP
MIB
This is an index to the organized data within a network device.
It defines the operating parameters that can be controlled or
monitored. When requesting the network manager to retrieve
or modify a particular piece of information about a network
device, the network manager transmits the request to that net-
work device. The agent in that device interprets the incoming
request, performs the requested task, and sends its response to
the network manager. The network manager collects all the
data from the various network devices and presents it in a con-
sistent form.
Commands
Using SNMP Version 1, the network manager can issue three
types of commands:
,
, and
GetRequest GetNextRequest
.
SetRequest
GetRequest
This command retrieves a single item or the first in a series
from a network device.
GetNextRequest
This command retrieves the next item in a series from a net-
work device.
SetRequest
This command writes information to a network device.
Messages
The network device issues two types of messages:
and
.
GetResponse
Trap
GetResponse
This message is the response to a network manager
or
command.
GetRequest GetNextRequest
A-2
TSU 120 User Manual
61202052L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A. Understanding SNMP
Trap
This is an unsolicited message issued by a network device to
report an operational anomaly or an alarm condition to the net-
work manager.
These messages are typically encased within informational
packets and transported over the LAN or WAN (wide area net-
work).
TSU 120 SNMP Access
By default, SNMP MIB Browser access to the TSU 120 IP
address with the configured community names, accesses the
host. The TSU 120 can also act as an SNMP proxy agent for
external units. To access MIB variables on externally chained
devices, append a period and the Unit ID of the device to the
Read and Read/Write community names. For example, if the
Read community name configured in the TSU 120 is
,
public
specifying
as the community name in the SNMP MIB
public.3
Browser allows reading SNMP MIB variables from externally
chained unit with a Unit ID of .
3
If the external unit's passcode is not the default, an entry must
be added to the Unit Access Table for
access. See
SNMP MIB
the Unit Access Table on page 8-5, for more information. How-
ever, SNMP traps for the unit can be forwarded without the
entry.
61202052L1-1
TSU 120 User Manual
A-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A. Understanding SNMP
SNMP Trap Configuration
Traps received by the TSU 120 from external units and the host
unit are converted into SNMP traps and forwarded to the con-
figured NMS. The source of the trap is uniquely identified at
the NMS by a combination of the IP address of the TSU 120,
and the Unit ID of the sending device. The Unit ID is present in
the trap packet appended to the end of the trap community
packet name, for example
. It is also included as an
public.4
Octet String variable (
) in the trap packet as
adProdPhysAddress
defined in the individual product MIBs. The latest versions of
the product MIBs, by default, display the appended trap com-
munity name in their descriptions.
Typical steps required for Management Station trap configura-
tion are loading the device specific MIBs and loading or creat-
ing device-specific Trap Definition Files. The current product
MIBs contain keywords embedded in comments that can be
used by some network management platforms to automatically
generate Trap Definitions. Otherwise, the descriptions may be
used as a template for Trap Definitions.
If individual option card port and slot identification is
required, it is present in the four- byte
field
adProdPhysAddress
of the trap packet. The first two bytes are the Unit ID of the
base controller (least significant byte first). The next two bytes
are port and slot number. This field is the second object identi-
fier in all traps sent from TSU/TDU products. For traps from
the ISU 512, the Unit ID is the first object identifier. See the
product MIBs for more information
Definitions for Poll Link Up/Down traps are included in the
TSU 120e MIB file:
.
TSU 120e.MIB
The TSU 120 and TSU 120e share the same MIB.
A-4
TSU 120 User Manual
61202052L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A. Understanding SNMP
SNMP MIB BROWSER CONFIGURATION
The following steps, shown in Table A -1 are required to config-
ure Network Manager MIB variable access through the TSU
120:
Table A-1. How to Configure Network Manager MIB
Step
1
Action
Load the desired product MIBs on the network management station.
If, for example, the administrator is managing TSU 120 and ISU 512
devices, load
, and
.
TSU 120.MIB, ISU512.MIB
RFC1406.MIB
2
Create device entries in the NMS database for all units that are to be
managed through the TSU 120. The host unit should be configured as
the proxy agent for the external units. The IP address or host name
used for the proxy designation is that of the TSU 120.
3
4
Set community names in the device’s entries for external units to the
TSU 120 community name with the device Unit ID appended as
defined in the previous section TSU 120 SNMP ACCESS on page A-3.
Set the device timeout for all device entries in the NMS device data-
base to five seconds, including the host unit.
61202052L1-1
TSU 120 User Manual
A-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A. Understanding SNMP
SNMP MIB Files Supported by the TSU 120
Standard MIBs
MIB-II (RFC-1213)
DS1 T1/E1 MIB (RFC-1406)
Ethernet MIB (RFC-1643)
(TSU 120e)
ADTRAN Enterprise-specific MIBs
ADTRAN Product MIB (ADTRAN.MIB)
ADTRAN DS1 extensions MIB (ADS1.MIB)
TSU/TDU Enterprise MIBs (TSU 120e.MIB)
The standard MIB files are
usually included with most
The latest version of the ADTRAN enter-
prise specific MIBs are available from the
SNMP network management following sources:
software.
•
•
•
ADTRAN anonymous ftp site:
ftp.adtran.com
By dial-up from the BBS:
256 -963-8169)
ADTRAN web site:
http://www.adtran.com
A-6
TSU 120 User Manual
61202052L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Understanding TR-08
Appendix B
The TSU 120 chassis functions as a Remote Terminal in Digital Loop
Carrier and as Integrated Digital Loop Carrier Systems as described in
TR-TSY 000008. The TSU 120 supports SLC96 framing, Mode I opera-
tion, ORB-13 and ORB-16 alarm formats, alarm reporting, and user-de-
finable BPV threshold detection rate.
A basic familiarity with DLC systems, IDLC systems and TR-TSY-
000008 is assumed, but the following information will be useful:
•
All received TR-TSY-000008 specific alarms are reported locally
within the history feature of the TSU 120.
•
When the DISABLE ALARMS option is selected, no alarms will be
sent on the DLF, but received alarms will be reported locally in the
history.
•
•
•
Other alarms normally reported by the TSU 120 will also be placed
in history.
Each TSU 120 needs to be configured as the A SHELF, as it is provi-
sioned as a separate entity.
All alarms will refer to A SHELF when received from TSU 120.
612020129L1-1
TSU 120 User Manual
B-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B. Understanding TR-08
Table B-1 explains what conditions trigger alarms and how alarms are
processed when received by the TSU 120.
Alarm Conditions
Table B-1.
Name
FELP
Explanation
When the TSU 120 receives a FELP alarm, it will loop
the incoming data directly to the outgoing data. LINE
ON is placed in history. The alarms and loopback are
cleared when FELP is no longer received.
Loss of Data
The TSU 120 will send MINOR ALARM and the A
SHELF ALARM for 2.5s when it quits receiving the
data link on the T-Span. It will also report TR-08 DL
Down in the history. After 2.5s, MAJOR ALARM, A
SHELF ALARM are sent across the Data Link.
OOF
The TSU will send MINOR ALARM and A SHELF
ALARM upon receiving an out-of-frame condition.
TR-08 DL Down and RED ALARM are declared in
history for severe framing errors. After 2.5s, MAJOR
ALARM, A SHELF ALARM are sent across the Data
Link.
Loss of Signal The TSU 120 will send MINOR ALARM and the A
SHELF ALARM for 2.5s when it quits receiving a
signal from the far end. It will also report TR-08 DL
Down and LOS in the history. After 2.5s, MAJOR
ALARM, A SHELF ALARM are sent across the Data
Link, and RED ALARM is declared in history.
BPVs
BPVs that are received at a rate greater than the
threshold set under TR-08 options, will cause
MINOR ALARM and A SHELF ALARM to be sent
on the DL. If the BPVs remain above the threshold for
2.5s, the TSU 120 will send MAJOR ALARM on the
DL. No events are placed in history.
Protection
Line Switch
The TSU will not respond to this alarm.
B-2
TSU 120 User Manual
612020129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B. Understanding TR-08
TR-08 DS0 Conversion Table
Table B-2 contains the mapping conversions needed to map voice ports
to the TR-08 network.
TR-08 DS0 Conversion Table
Table B-2.
DS0
TR-08 Channel Number
Port
1
3
5
7
1
2
3
4
1.1
1.2
1.3
1.4
612020129L1-1
TSU 120 User Manual
B-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B. Understanding TR-08
B-4
TSU 120 User Manual
612020129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Network Pinouts
Appendix C
WIRING
Network Pinouts
On the rear panel of the TSU 120 is an eight-position modular
jack labeled NETWORK. This connector is used for connecting
to the network. See Table C-1 for the pinout for the network con-
nector.
Connections
The network connections are as follows:
Connector type (USOC) RJ-48C
Part number
AMP# 555164-2
Table C-1. Network Pinouts
Pin
Name
Description
1
R1 RXDATA-RING Receive data from the network
2
3
T1 RXDATA-TIP
UNUSED
Receive data from the network
4
R TXDATA-RING Send data toward the network
5
T TXDATA-TIP
UNUSED
Send data toward the network
6,7,8
61202129L1-1
TSU 120 User Manual
C-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C. Network Pinouts
Control In/Chain In
This is used as an EIA-232 port for connection to a computer or
modem (Control In) or to another TSU 120 or TSU 100 (Chain
In). See Table C-2 for the pinout for the control/chain-in connec-
tor.
Connections
The chain-in connections are as follows:
Connector type
Part number
RJ-48
AMP# 555164-2
Table C-2. Control In/Chain in Pinout
Pin
1
Name
GND
Description
Ground - connected to unit chassis
Request to send - flow control
Data received by the TSU 120
2
RTS
3
RXDATA
UNUSED
TXDATA
UNUSED
CTS
4
5
Data transmitted by the TSU 120
Clear to send - flow control
6,7
8
C-2
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C. Network Pinouts
Chain Out
This is used to connect to another TSU 120 chain-in connector.
See Table C-3 for the pinout for the chain-out connector.
Connections
The chain-out connections are as follows:
Connector type RJ-48
Part number
AMP# 555164-2
Table C-3. Chain Out Pinout
Pin
Name
Description
1
GND
Ground - connected to unit chassis. Connected to
GND of next unit (pin 10).
2
3
UNUSED
TX DATA
Data transmitted to chained units by the TSU 120.
Connect to RX DATA of the next unit (chain-in pin
3).
4
5
UNUSED
RX DATA
Data received from chained units by the TSU 120.
Connect to TX DATA of the next unit (chain-in pin
5).
6,7,8 UNUSED
61202129L1-1
TSU 120 User Manual
C-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C. Network Pinouts
Nx56/64 DTE (V.35)
See Table C-4 for the V.35 pinout Nx56/64 DTE pinout.
Connections
The DTE interface pinout is as follows:
Connector type
Part number
V.35
AMP# 92-4883-3-x
Table C-4. V.35 Pinout - Nx56/64 DTE
Pin
Name
101
102
105
106
107
109
—
Description
Protective ground (PG)
A
B
Signal ground (SG)
C
Request to send (RTS) from DTE
Clear to send (CTS) to DTE
Data set ready (DSR) to DTE
Received line signal detector (DCD) to DTE
Local Loopback (LL)*
D
E
F
L, J
N, BB
R
—
Remote loopback (RL)*
104
104
115
115
103
103
114
114
113
113
—
Received data (RD-A) to DTE
Received data (RD-B) to DTE
RX clock (RC-A) to DTE
T
V
X
RX clock (RC-B) to DTE
P
Transmitted data (TD-A) from DTE
Transmitted data (TD-B) from DTE
TX clock (TC-A)
S
Y
AA
U
TX clock (TC-B)
External TX clock (ETC-A) from DTE
External TX clock (ETC-B) from DTE
Test mode (TM) to DTE
W
NN, K
*(ignored by TSU 120)
C-4
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C. Network Pinouts
Base DSX-1 (PBX)
See Table C-5 for Base DSX-1 pinout connections for either-posi-
tion Modular Jack Interface.
Connections
The modular jack interface pinout is as follows:
Connector type RJ-48C
Table C-5. Pinout Connectors for Modular Jack Interface
Pin
1
Name
Description
R1 TXDATA-RING Send data towards the DTE (PBX)
2
T1 TXDATA-TIP
UNUSED
Send data towards the DTE (PBX)
—
3
4
R RXDATA-RING Receive data from the DTE (PBX)
5
T RXDATA-TIP
Receive data from the DTE (PBX)
—
6, 7, 8 UNUSED
61202129L1-1
TSU 120 User Manual
C-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C. Network Pinouts
10BaseT (TSU 120e only)
10BaseT is used to connect the TSU 120 to the local area net-
work. See Table C-6.
Connections
The required wiring connections are:
Connector type (USOC)
Part number
RJ-45
AMP # 555164-1
Table C-6. 10BaseT Ethernet (TSU 120e only)
Pin Name (TO NIC)
Pin1
TX1
TX2
RX1
RX2
Pin 2
Pin 3
Pin 6
C-6
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
System Messages
Appendix D
This appendix lists and defines the alarm and status messages
that appear on the TSU 120 screen.
ALARM MESSAGES
Network Interface (NI)
Red Alarm
NI unable to frame align with incoming signal
Yellow Alarm
Remote alarm indication (RAI) being received
from far end
Blue Alarm
Unframed all ones (1s) (AIS) being received at NI
No signal detected at NI
Loss of Signal
Nx56/64 Interface
The following messages indicate an alarm condition on the
Nx56/64 card:
Clock Slip
Difference in frequency of the data clock at the
network and DTE
PLL Alarm
Unable to achieve Phase-locked Loop on the
clock provided by the network interface.
Zeros Alarm
No EXT Clock
All zeros (0s) data being sent toward the network
interface
No external transmit clock at DTE (only appears
if EXT CLK is selected)
61202129L1-1
TSU 120 User Manual
D-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D. System Messages
DSX-1 (PBX) Interface
The following messages indicate a condition on the Base DSX-1
(PBX) interface:
Red Alarm
Not able to frame data coming to the DSX-1
interface; sometimes referred to as out-of-
frame (OOF)
Yellow Alarm
Blue Alarm
Remote alarm indicator (RAI) being
received by the DSX-1 interface
Receiving unframed all 1s at the DSX-1
interface [alarm indicator signal (AIS)]
Loss of Signal
No signal detected by the DSX-1 interface
Status Messages
Network Interface (NI)
Payload On
Line On
Payload loopback activated
Loopback off
Loopback Off
Factory Restore
Power On
All loopbacks deactivated
Factory setting restored
Unit powered on
Self-Test
Internal self-test performed
TR-08 data link is down
TR-08 data link is up
TR-08 DL Down*
TR-08 DL Up*
Minor Alarm*
Loss of sync, carrier los, BPV threshold
exceded, or data link failure
Major Alarm*
Conditions for a minor alarm have contin-
ued for greater than 2.5 seconds
TR-08 alarm messages appearing in the alarm or history
log have been received from the far end. If the NI detects
one of the aove conditions, it will send the appropriate
alarm (if enabled) to the far end but no message will ap-
pear in the alarm or history log.
D-2
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D. System Messages
Nx56/64 Interface
The following messages indicate the status of the Nx56/64
card:
Loop Up
Data is looped at both the network inter-
face and DTE interface of the card
Remote Loop Up
511 Pattern On
Loop Down
Sending V.54 pattern in an attempt to
loop up a remote device
Sending 511 pattern towards the network
interface
Data is no longer looped back at the net-
work interface or DTE interface
511 Pattern Off
No longer sending 511 pattern towards
the network interface
DSX-1 (PBX) Interface
The following messages indicate the status of the DSX-1 inter-
face:
Frame Slip
Indicates a Frame Slip has occurred on the
DSX-1 interface; this is present in Alarm
History only
Line Loop Up
Port Loop Up
Loopdown
Line loopback activated
Port loopback activated
Loopback has been deactivated
61202129L1-1
TSU 120 User Manual
D-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D. System Messages
D-4
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Appendix E
ELECTRICAL SPECIFICATIONS
T1/FT1 Interface
T1 Line Rate
Line Code
Framing
1.544 Mbits/s +/- 75bps
Bipolar,RZ; AMI or B8ZS
D4(SF), ESF, or SLC96
FT1 Line Rate
DS0 Channelized (multiple of 64 kbps)
Transmit Timing Network, DTE, U-BR1TE Secondary NI,
Normal (CSU) or Internal
Input Signal
Line-Build-Out
Connector
0 to -36 dB (DS-1)
0, 7.5, 15, 22.5 dB, AUTO
RJ45
Test Jacks
Bantam jacks: TX and RX (to Network) and
MON
Compatibility
T1 Interface
ESF Format Interface
ESF Performance Monitoring TR. 54016 and T1.403
Pub 62411
TR. 194
Approvals:
FCC Part 15
FCC Part 68
UL 1950
61202129L1-1
TSU 120 User Manual
E-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix E. Specifications
Nx56/64 (V.35 Interface)
DCE Interface
Rates
CCITT V.35 Synchronous
56kbps - 1.536Mbps in 56k or 64k incre-
ments
Clock Options
Tests
Normal/Inverted and internal/external
Local Loopback (bilateral)Remote Loop-
back (V.54)
Test Pattern
511 with errored seconds display and
error inject capability
Data inversion
Menu selectable
1s Density Protection Force 1s to network after one second of
consecutive zeros from DTE. User select-
able (On/Off)
CTS, DCD, DSR
Connector
Normal or Force On
Winchester (V.35) female (on the Y cable)
DSX-1 Interface
Line Interface
DSX-1 per ANSI T1.102
DSX Receiver Input Range
-10 dBdsx to +6 dBdsx
1.544 Mbps
Line Rate
Capacity
Line Codes
Framing
1 to 24 DS0s
AMI, B8ZS
ESF per ANSI T1.403 and
AT&TPub. TR 54016, D4 per
AT&T Pub. 62411
Line Length
Timing
-7 dBdsx to 655 ft in 110 ft steps
Supports network, secondary,
and CSU timing modes
Test Capability
Line loopback, port loopback
(internal toward mux)
Connector
Test Jacks
RJ45
RX MON, RX and TX (toward
PBX)
E-2
TSU 120 User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix E. Specifications
MANAGEMENT INTERFACES
Chain In/Out Ports
Interface Devices
PC Serial Port, Modem or SLIP connec-
tion to router
Interface Type
Data Rates
EIA-232
2400, 1200, 2400, 4800, 9600, 19200,
38400
Data Format
Protocols
EIA-232 N81
T-WATCH/ADLP, ATEL/ADLP, TCP/
IP/SLIP
Connector
RJ-45
10BaseT Interface (TSU 120e only)
Interface
Rate
IEEE 802.3 Compliant
10 Mbps
Connector
Receiver
Protocols
RJ45
accepts signal > 300mV
Network:
Transport: TCP, UDP
Service: SNMP, TELNET, ICMP, ARP,
PING, T-WATCH
IP
Option Slot Interface
Interface
ADTRAN proprietary, accepts standard TSU
Option Modules.
Chassis Specifications
Height
Width
Less than 3.5 inches (will fit in a 2U rack
mount opening)
Two units will fit within a 19-inch rack
61202129L1-1
TSU 120 User Manual
E-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Numerics
BPVs, alarm condition TR-08 B-2
0.1 Nx56/64 Menu Items 4-5
0.1 Nx56/64 Port Configuration (Port
Config) Menu Items 5-18
0.2 DSX-1 Menu Items 4-6
10BaseT Interface (TSU 120e) 2-6
C
Canadian Emissions Requirements
Canadian Equipment Limitations viii
Cancel Tests, test menu 7-10
Chain In (PC), port 2-8
Chain In/Chain Out 2-8
Chain In/Out Ports, management
10BaseT
Interface,
interface E-3
10BaseT, pinouts C-6
A
Active Alarms, list of 4-3
ADTRAN PC Management Program
3-10
ADTRAN PC Program, T-WATCH
Pro 3-10
Chain Port Output 2-6
change/set a passcode, how to 6-4
Chassis Specifications, TSU 120 E-3
Clear Port Alarm 4-7
ADTRAN shipment, items included
in 2-1
ADTRAN Web Site iii
ADTRAN Year 2000 (Y2K) Readiness
Disclosure iii
Affidavit for connection of CPE to
1.544 MBPS and/or subrate digital
services x
Commands, SNMP network manager
A-2
Compliance, Y2K iii
configuration applications, TSU 120
1-4
Affidavit
Requirements
for
Create Temp Selection, how to 5-17
Customer Service xiii
Connection to Digital Services ix
Agent, SNMP component A-1
Alarm Conditions, TR-08 B-2
alarm messages D-1
D
B
data port identification 3-8
Base DSX-1 (PBX), pinouts C-5
DBU Configuration Menu Items 5-21
Base DSX-1, clock source option 5-7
61202129L1-1
TSU 120e User Manual
Index-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
default unit passcode, how to set in
unit access table 8-7
Delete Unit, how to in unit access
table 8-7
with RS-232 port 8-10
Front
Menu
Structure,
Dial backup, option module 1-3
Display Only Data Fields, what they
do 3-7
DS0 Map A and DS0 Map B 5-15
DS0 Map Example 5-16
Front Panel Menu Tree, example 3-6
front panel, descriptions of 3-1
Full Drop and Insert, option module
DS0 Temp Map 8-2
DSU DP, option module 1-3
DSU/DSX Status LEDs 3-4
DSX-1 (PBX) Interface 2-6
DSX-1 (PBX) Interface, system
messages D-2
GetResponse, SNMP message A-2
Grounding Instructions 2-2
DSX-1 Interface E-2
DSX-1 interface status message D-3
DSX-1 Test Interface 2-6
DSX1, option module 1-3
DTE Timed Clock Source 5-8
DTE timing, clock source option 5-8
Initializing the Temp Map, how to for
telnet/terminal menu 8-3
internal timing,
clock source option 5-9
E
Editing the Temp Map, for telnet/
terminal menu 8-4
EIA-232 Connection, T-WATCH Pro
3-11
electrical specifications, TSU 120 E-1
E-mail iii
ENET Address, utility menu 6-5
ENET Status 4-7
Environmental Specifications E-4
Exit Any Menu Field Operation Or
Display, how to 3-8
L
LOCAL LOOPBCK, test menu 7-4
Loopback Tests, test menu 7-3
Loss of Data, alarm condition TR-08
B-2
M
Management Configuration, telnet/
terminal menus 8-5
F
Factory Restore, utility menu 6-3
Faxback Document Line, Y2K iii
FCC Regulations v
Management Interfaces E-3
Map Configuration, how to for the
telnet/terminal menu 8-3
Map Exchange menu, configuration
menu 5-14
features, TSU 120 1-2
Federal
Commission
Communications
Radio Frequency
Map in Use 5-14
Interference Statement vi
menu tree, configuration 5-2
Index-2
TSU 120e User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
menu tree, status 4-1
menu tree, test menu 7-2
menu tree, utility 6-2
MIB browser configuration,
SNMP A-5
MIB, SNMP component A-2
Modify Unit, how to in unit access
table 8-7
Nx56/64 status message D-3
NxIQ, option module 1-3
O
OOF, alarm condition TR-08 B-2
option module architecture,
description of 1-4
Module Status LEDS 3-4
Option Slot Interface, management
interface E-3
N
Network (NI), configuration menu 5-
3
Overview, TSU 120 1-1
Network Interface Errors 4-3
Network Interface Loopbacks, test
menu 7-3
Passcode Automatic Timeout, utility
Network Interface port 2-5
Network Manager MIB, how to
configure A-5
Network Manager, SNMP component
A-1
Port Status, signals monitored on data
ports 4-4
network menu items, configuration
menu 5-3
Port Test Menu Items for 0.1 Nx56/64,
network performance reports 4-2
Network Pinouts C-1
Network Test Interface 2-5
Network Tests 7-3
Network Tests, test menu 7-3
NI ERRORS 4-3
port utility, option ports 6-5
power connection, TSU unit 2-2
NI PERF RPTS 4-2
No Passcode Desired, utility menu 6-
4
No Unit ID Desired, what to do if 6-5
normal CSU timing, clock source
timing 5-11
Protection Line Switch, alarm
Nx56/64 (V.35 Interface) E-2
Nx56/64 DTE (V.35), pinouts C-4
Nx56/64 interface, status message D-
3
QRSS Pattern, test menu 7-5
Quit Session, for telnet/terminal
session 8-10
Nx56/64 Menu Items 5-18
Nx56/64 Serial Interface 2-5
Nx56/64 serial interface, TSU option
module 1-3
R
rear panel layout 2-4
Receipt Inspection, of TSU unit 2-1
61202129L1-1
TSU 120e User Manual
Index-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
REMOTE LOOPBCK, test menu 7-4
remote menu access, telnet menus 8-5
Remote Port, displaying status on
control-in remote port 4-7
repair and return information xiii
Router, option module 1-3
Router, PBX, Video Conferencing
Applications 1-4
Run Self-test 7-7
telnet menus, displaying from
remote device 8-5
12
telnet/terminal main menu 8-1
test jacks, in and out 2-6
Interface,
electrical
a
Run Self-Test, test menu 7-7
S
Safety instructions xii
secondary timing, clock source option
5-10
TR-08 DS0 Conversion Table B-3
1-4
Self-Test, on power-up 2-7
Serial Number, utility menu 6-5
Set Chain Port input 2-8
Set the Data Field, how to 3-7
Set the Unit Identification 6-5
Set Unit Identification, how to 2-7
Set User Passcode, how to 2-7
SetRequest, SNMP command A-2
SNMP MIB Browser Configuration A-
5
TSU 120, overview 1-1
SNMP Read Community 8-7
SNMP Read/Write Community 8-7
SNMP Trap Community 8-8
SNMP TRAP CONFIGURATION A-4
SNMP, about A-1
TSU Option Modules 1-3
T-WATCH Pro, EIA-232 connection
3-11
SNMP, Basic Components A-1
SNMP, how to use 3-11
SNMP, Message A-2
T-WATCH Pro/LAN connection,
Software Revision (Software Rev) 6-5
status menu tree 4-1
status messages D-1
Status Messages, TSU 120 D-2
Status, Config, Util, and Test Menu
Options 8-2
U
U-BR1TE, clock source timing 5-11
U-BR1TE, option module 1-3
unit access table, how to add a new
unit 8-6
Unit ID, utility menu 6-4
utility menu tree 6-2
V
View History 4-4
Index-4
TSU 120e User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Voice Interface, option module 1-3
Y
Y2K Compliance iii
Y2K Project Line iii
Y2K, Faxback Document Line iii
W
Warranty and Customer Service xiii
Wiring C-1
61202129L1-1
TSU 120e User Manual
Index-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Index-6
TSU 120e User Manual
61202129L1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Support Information
Presales Inquiries and Applications Support
Please contact your local distributor, ADTRAN Applications Engineering,
or ADTRAN Sales:
Applications Engineering (800) 615-1176
Sales
(800) 827-0807
Post-Sale Support
Please contact your local distributor first. If your local distributor cannot
help, please contact ADTRAN Technical Support and have the unit serial
number available.
Technical Support
(888) 4ADTRAN
Repair and Return
If ADTRAN Technical Support determines that a repair is needed, Technical
Support will coordinate with the Customer and Product Service (CaPS) de-
partment to issue an RMA number. For information regarding equipment
currently in-house or possible fees associated with repair, contact CaPS di-
rectly at the following number:
CaPS Department (256) 963-8722
Identify the RMA number clearly on the package (below address), and re-
turn to the following address:
ADTRAN Customer and Product Service
6767 Old Madison Pike
Progress Center
Building #6 Suite 690
Huntsville, AL 35807
RMA # _____________
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|