6DIHZDWFKꢀ3UR ꢀꢁꢂꢂꢂ(1
(QWUHSUHQHXUꢀꢁꢂꢂꢂ(1
6HFXULW\ꢀ0DQDJHUꢀꢁꢂꢂꢂ(1
6HFXULW\ꢀ6\VWHPV
8 *
VHU·Vꢀ XLGH
Meets ADT Security Services Triple Standards
Requirements:
Standards for Security and Fire
Standard for False Alarm Reduction
7
167-0495:110
California State Fire Marshal Approval
K5309V3 6/02
Model SASW3000EN
Download from Www.Somanuals.com. All Manuals Search And Download.
7DEOHꢀRIꢀ&RQWHQWV
System Over view .................................................................................................................... 5
Introduction .......................................................................................................................... 5
System Basics ....................................................................................................................... 5
Using the Voice Message Center ......................................................................................... 7
Ab ou t Th e Tou ch p a d s ........................................................................................................... 8
General Information ............................................................................................................. 8
F u n ction s of th e Tou ch p a d s ..............................................................................................10
E n tr y/E xit Dela ys .................................................................................................................12
Entry Delay......................................................................................................................... 12
Exit Delay............................................................................................................................ 12
Exit Alarms ......................................................................................................................... 13
Ch eck in g F or Op en Zon es ..................................................................................................14
Using the [∗] Key to Display and Announce System Status............................................ 14
Ar m in g th e System ...............................................................................................................15
Stay Mode: Arms Perimeter Only, Entry Delay On ......................................................... 15
Night-Stay Mode: Arms Perimeter Only, Plus Selected Zones ....................................... 15
Instant Mode: Arms Perimeter Only, Entry Delay Off.................................................... 15
Away Mode: Arms Entire System, Entry Delay On ......................................................... 15
Arming Commands ............................................................................................................. 16
Single Button Arming ........................................................................................................ 17
Single-Button “Step” Arming............................................................................................. 17
Usin g th e Keysw itch ............................................................................................................18
Using the Keyswitch........................................................................................................... 18
Disa r m in g a n d Silen cin g Ala r m s......................................................................................19
Using the [OFF] key ........................................................................................................... 19
Byp a ssin g P r otection Zon es ..............................................................................................20
Using the BYPASS Key...................................................................................................... 20
Quick Bypass ...................................................................................................................... 21
Ch im e Mod e ...........................................................................................................................22
View in g Cu r r en t Da te a n d Tim e ......................................................................................23
Viewing the Current Date and Time................................................................................. 23
Setting the Date and Time................................................................................................. 23
P a n ic Keys ..............................................................................................................................24
– 3 –
Download from Www.Somanuals.com. All Manuals Search And Download.
T a b l e o f C o n t e n t s
Ma cr o Key P r ogr a m m in g & Usa ge ...................................................................................25
About Macro Keys............................................................................................................... 25
Example of Macro Programming....................................................................................... 26
Using a Programmed Macro Key....................................................................................... 26
Usin g Device Com m a n d s ....................................................................................................27
P a gin g F ea tu r e .....................................................................................................................28
About Automatic Paging .................................................................................................... 28
About Manual Paging......................................................................................................... 29
Latch Key Paging ............................................................................................................... 29
Secu r ity Cod es & Au th or ity Levels..................................................................................30
About Security Codes ......................................................................................................... 30
Authority Level Definitions ............................................................................................... 30
How To Assign User Codes and Attributes....................................................................... 31
Accessin g Oth er P a r tition s (GOTO Com m a n d a n d Mu lti-P a r tition Ar m in g) ......32
About Accessing Partitions ................................................................................................ 32
Using the GoTo Command ................................................................................................. 33
Multi-Partition Arming ...................................................................................................... 33
Common Zone Operation.................................................................................................... 34
Sch ed u lin g .............................................................................................................................35
About Scheduling................................................................................................................ 35
Creating Schedules ............................................................................................................. 35
E ven t Loggin g P r oced u r es.................................................................................................37
About Event Logging .......................................................................................................... 37
Viewing the Event Log ....................................................................................................... 37
Table of Event Log Codes................................................................................................... 38
Testin g th e System (To Be Con d u cted Week ly) ............................................................39
Tr ou b le Con d ition s ..............................................................................................................41
Ma in ta in in g You r System ...................................................................................................44
F ir e Ala r m System (If In sta lled ) .......................................................................................45
Qu ick Gu id e to Ba sic System F u n ction s ........................................................................49
Su m m a r y of Au d ib le/Visu a l Notifica tion s ......................................................................50
R egu la tor y Sta tem en ts a n d Wa r n in gs ............................................................................52
Ch a r ts of You r System ’s F ea tu r es ....................................................................................54
– 4 –
Download from Www.Somanuals.com. All Manuals Search And Download.
6\VWHPꢀ2YHUYLHZ
,QWURGXFWLRQ
Congratulations on your ownership of an ADT Partitioned Security System. You've
made a wise decision in choosing it, for it represents the latest in security protection
technology today, and millions of premises are protected by ADT systems.
This system provides:
• Three forms of protection: burglary, fire* and emergency.
• At least one touchpad which provides control of system operation and displays
the system’s status
• Various sensors for perimeter and interior burglary protection
• Smoke or combustion detectors* designed to provide early warning in case of fire.
Your system may also have been programmed to automatically send alarm or status
messages over the phone lines to a Customer Care Center.
* Commercial installations and some residential systems may not include fire
protection – check with your installer.
6\VWHPꢀ%DVLFV
Bu r gla r y P r otection
• There are four modes of burglary protection: Stay, Night-Stay, Away, Instant.
STAY: arms perimeter zones only and entry delay is on
INSTANT: same as STAY, except entry delay is off
NIGHT-STAY: arms perimeter zones and selected interior zones; entry delay on
AWAY: arms perimeter and all interior zones, entry delay is on
• You can BYPASS selected zones while leaving the rest of the system armed.
• CHIME mode alerts you to the opening of protected doors and windows while the
system is disarmed.
F ir e P r otection
• Fire protection is always active (if installed) and an alarm sounds if a fire
condition is detected
• If necessary, you can manually initiate a fire alarm using the touchpad (if
programmed).
• Refer to the Fire Alarm System section for information regarding fire protection,
smoke detectors and planning emergency exit routes.
Secu r ity Cod es
• You were assigned a 4-digit security code during system installation.
• Use your security code when arming and disarming the system, and when
performing other system functions.
• Other users can be assigned different security codes.
• User codes can be assigned different authority levels, which define which system
functions a particular user can perform.
– 5 –
Download from Www.Somanuals.com. All Manuals Search And Download.
6\VWHPꢀ2YHUYLHZꢀꢁ&RQWLQXHGꢂ
Zon es a n d P a r tition s
• The system sensing devices have been assigned to various “zones,” which are
specific areas of protection (e.g., front door, kitchen window, etc.).
• Zone numbers are displayed at the touchpad when an alarm or trouble condition
occurs on a sensor.
• Partitions provide two independent areas of protection, with each partition
containing a group of zones that can be armed and disarmed without affecting
other zones or users.
• Partitioned systems can include a common zone area, which is an area shared by
users of both partitions (such as a lobby in a building).
• Partition identification: 1 = partition 1; 2 = partition 2; 3 = common zone.
Ar m in g, Step -Ar m in g a n d Disa r m in g Bu r gla r y P r otection
• The system must be armed before the burglary protection can sense intrusions.
• To arm your system, enter your user code followed by the desired arming key.
• If programmed, the [#] key can be pressed instead of entering the security code
when arming the system.
• You can also use the step-arming key to arm the system, if programmed.
• To disarm the system, enter your user code then press the [OFF] key.
• Step-arming, if programmed, lets you use a function key to arm the system in one
of three modes by simply pressing the key repeatedly, where:
first press arms STAY; second press arms NIGHT-STAY; third press arms
AWAY.
Ala r m s
• When an alarm occurs, both the touchpad and external sounders will sound, and
the touchpad will display the zone(s) causing the alarm.
• If your system is connected to a Customer Care Center, an alarm message will
also be sent.
• To stop the alarm sounding, simply disarm the system.
Mem or y of Ala r m
• When an alarm condition occurs, the touchpad displays the number(s) of the
zone(s) that caused the problem, and displays the type of alarm (e.g., “FIRE”).
• The message remains displayed even after disarming the system, but can be
cleared with another “off” sequence.
F u n ction Keys
• The “A”, “B”, “C”, and “D” keys on the touchpad can be programmed to perform
various functions.
• Functions include: activate a Panic alarm; arm the system; provide step arming;
switch lights on/off; send a message to a pager; display Time/Date; start a Macro
– 6 –
Download from Www.Somanuals.com. All Manuals Search And Download.
6\VWHPꢀ2YHUYLHZꢀꢁ&RQWLQXHGꢂ
P h on e Access
• If included, a phone module permits you to access the system via a touch-tone
phone, either on-premises or by call-in when away.
• When you call in, the phone module announces system status over the telephone,
and you can arm/disarm the system and perform most function commands
remotely using the telephone keys.
• Complete information for using these features is provided with the voice module.
P a gin g F ea tu r e
• If programmed, the system can automatically send certain system condition
messages to up to four pagers.
• The display consists of code numbers that identify the type of condition that has
occurred.
Sch ed u lin g
• Your system can be programmed to automatically perform certain functions (e.g.,
arm the system) at a predetermined time each day.
8VLQJꢀWKHꢀ9RLFHꢀ0HVVDJHꢀ&HQWHU
PLAY KEY
AND
UP VOLUME
The Voice Touchpads feature a voice message
center that lets you record and playback one
message.
LCD
DISPLAY
RECORD
KEY
VOLUME
KEY
SPEAKER
• The message can be up to 2.5-minutes long
• The message remains in the Touchpad’s memory
OFF
1
AWA
Y
STA
Y
ARMED
READY
2
3
6
9
RECORD
VOLUME
PLAY
until a new message is recorded.
BYPASS
LEDs
4
5
8
0
TEST
MESSAGE
INSTANT
READY
CODE
CHIME
7
• The volume control of the message is adjustable.
MIC
#
STATUS
VOICE
FUNCTION
• Refer to the procedures below when using the
Message Center functions.
MICROPHONE
STATUS
KEY
VOICE FUNCTION
KEY KEY
DOWN
VOLUME
Messa ge Cen ter F u n ction s
To…
P r ess th ese k eys…
Notes…
record a
message
The red MESSAGE LED lights.
Message remains in memory
until a new message is recorded.
[#] FUNCTION + [0] VOICE + [1] RECORD
end
recording
The red MESSAGE LED flashes,
indicating message waiting.
[1] RECORD
play a
message
The recorded message plays and
the red MESSAGE LED turns off.
[#] FUNCTION + [0] VOICE + [3] PLAY
adjust the
volume
Adjusting message volume also
adjusts status volume. Volume
cannot be adjusted while playing.
[#] FUNCTION + [0] VOICE + [2] VOLUME keys,
then press volume key [3] ↑ (up) or [6] ↓ (down)
– 7 –
Download from Www.Somanuals.com. All Manuals Search And Download.
$ERXWꢀ7KHꢀ7RXFKSDGV
*HQHUDOꢀ,QIRUPDWLRQ
Your touchpads allow you to control all system functions and feature the following:
• A telephone style (digital) keypad
• Liquid Crystal Display (LCD) which shows the nature and location of all
occurrences
• Built-in sounder which will sound during alarms and troubles. The sounder also
"beeps" during certain system functions and when depressing any of the keys (to
acknowledge the key press).
• Backlighting of the LCD display windows. Backlighting turns on when any key is
pressed, and when opening an entry/exit door while the system is armed. This
feature is helpful when a touchpad is located in a dimly lit area.
• Some touchpads have a voice feature that announces the nature and location of all
occurences. Voice touchpads also announce any faulted zones when Chime mode is
on. Ask your installer if this option has been programmed for your system.
IMP OR TANT: If the touchpad beeps rapidly upon entering the premises, it indicates that
an alarm has occurred during your absence and an intruder may still be on the premises.
LEAVE IMMEDIATELY and CONTACT THE POLICE from a nearby safe location.
Your touchpads are functionally the same, but may have different types of displays,
depending on the type installed with your system. To access the keys on the touchpad,
simply open the swing-down door.
Cu stom E n glish
Disp la y
2-line Custom English display touchpads feature a 2-line,
32-character alphanumeric LCD which displays system
messages in friendly English. These touchpads can also be
programmed with custom zone descriptors.
E n glish Disp la y
English display touchpads are functionally identical to Custom
English display touchpads, but the LCD display uses pre-
designated words to identify the nature and location of
occurrences.
Voice Tou ch p a d s Voice Touchpads (if installed), are functionally the same as other
touchpads, except that these touchpads can provide the following:
• Voice announcements of system status (see Checking for Open
Zones section)
• Voice chime, which can alert you to the opening of doors and
windows while the system is disarmed (see Voice Chime in
Chime mode section)
• Message center, which lets you record and playback messages
(see Using the Voice Message Center in the System Overview
section).
– 8 –
Download from Www.Somanuals.com. All Manuals Search And Download.
$ERXWꢀ7KHꢀ7RXFKSDGVꢀꢁ&RQWLQXHGꢂ
(QJOLVKꢀ'LVSOD\ꢀ7RXFKSDG
AWAY: All burglary zones, interior and
NO AC
TEST
NOT READY
CHIME BAT
AWAY
perimeter, are armed.
BYPASS
STAY: Perimeter burglary zones, such as
protected windows and doors, are
armed.
STAY
ALARM
FIRE
CHECK INSTANT
ENGLISH DISPLAY TOUCHPAD
INSTANT: Entry delay is turned off:
Lit with STAY = Instant mode
Lit with AWAY = Maximum mode
BYPASS: This appears when one or more burglary protection zones have been
bypassed.
NOT READY: Appears when burglary portion of the system is not ready for arming
(due to open protection zones). The system is ready to arm when this
message disappears and the READY indicator light comes on.
NO AC: Appears when AC power has been cut off. System is operating on
backup battery power.
AC: Appears when AC power is present.
CHIME: Appears when the CHIME feature is activated.
BAT: Low battery condition in a wireless sensor (if zone number displayed)
or low system battery (if no zone number displayed).
ALARM: Appears when an intrusion has been detected and the system is armed
(also appears during a fire alarm or audible emergency alarm).
Accompanied by the protection zone in alarm.
CHECK: Appears when a malfunction is discovered in the system at any time or
if an open is detected in a FIRE zone at any time or a fault in a
DAY/NIGHT burglary zone during a disarmed period. Accompanied by
a display of zone number in trouble.
FIRE: Appears when a fire alarm is present. Accompanied by a display of the
zone in alarm.
A FIRE display also appears when a fire alarm is manually activated,
accompanied by a display of emergency key zone number programmed
for fire.
– 9 –
Download from Www.Somanuals.com. All Manuals Search And Download.
)XQFWLRQVꢀRIꢀWKHꢀ7RXFKSDGV
NOTE: The functions printed directly on the keys
9.
8 CODE
for other users of the system.
9 CH IME
Used to assign additional user codes
indicate their primary purpose (most require entry of
a security code first); the functions printed under
some keys (shown in brackets in the list below)
indicate an alternate function available on voice
touchpads only.
and off.
Turns CHIME mode on
10.
When on, the opening of windows or doors while
the system is disarmed will sound 3 beeps at the
touchpad(s).
1. DISP LAY WINDOW.
Cu stom En glish Displa y Tou ch pa d s: 2-line, 32-
character Liquid Crystal Display (LCD) touchpads
that display protection point identification, system
status, and messages.
11.
#
This key can be used for "Quick Arming" of
the system without use of a
security code (if programmed).
En glish Displa y Tou ch pa d s: Display protection
zone ID and system status messages using pre-
designated words in the LCD display.
[F UNCTION] Used to enable voice and volume
functions.
12. Key
0
[VOICE ] Used to activate the
1 OFF
the system,
Disarms burglary portion of
2.
3.
RECORD, VOLUME, and PLAY functions.
silences alarms and audible trouble indicators,
and clears visual display after problem's
correction.
13. ∗ R E ADY Used to display all open protection
zones.
[R E CORD] Used to record up to a 2.5-minute
message.
[STATUS] Used to announce system status and
faulted zones (if any exist).
2 AWAY
Arms the entire burglary system,
14. KEYS 0–9: Numeric keys used to enter your
security code(s).
perimeter and interior.
15. MIC: Microphone for Message Center recordings.
[VOLUME] Used with the desired ↑ [3] or ↓ [6] keys
to set playback and system announcement volume.
16. MESSAGE LED: (red). Flashes red when
message waiting or lights steady red when
recording a message.
4. 3 STAY
Arms perimeter portion of burglary
system only. Interior protection is not armed,
allowing movement within premises without
causing an alarm.
17. READY INDICATOR: (green) Lit when the
system is ready to be armed (no faults present).
While the system is disarmed, this indicator will
go on and off as protection zones are closed and
opened.
[P LAY] Used to playback a recorded message.
[↑] Used with VOLUME key to raise volume.
18. ARMED INDICATOR: (red) Lit when the
5.
4
This is not a Function key. Used only as
a numeric key.
Tests the system and alarm sounder if
system has been armed.
19. F UNCTION KEYS: Keys A, B, C, D may have
been programmed for a variety of functions,
including panic (emergency) functions. For details,
see the Function Keys section.
.
5
TEST
6
disarmed. Refer to Testing The System section for
test procedures.
20. INTERNAL SP EAKER: The built-in speaker
mimics the alarm sounder during alarms, and will
also "beep" during certain system functions. The
speaker also provides voice playback for any
recorded messages.
7. 6 BYP ASS Removes individual protection zones
from being monitored by the system.
[↓]Used with VOLUME key to lower volume.
8.
7INSTANT Arms in manner similar to the STAY
mode, but without the entry delay feature.
Entering via an entry/exit door will cause an
instant alarm.
– 10 –
Download from Www.Somanuals.com. All Manuals Search And Download.
)XQFWLRQVꢀRIꢀWKHꢀ7RXFKSDGVꢀꢁ&RQWLQXHGꢂ
1
2
3
4
20
19
18
17
5
6
OFF
1
AWAY
TEST
CODE
STAY
BYPASS
CHIME
2
5
8
0
3
6
9
7
8
16
15
4
7
9
INSTANT
READY
#
10
14
11
13
12
Custom English Display Voice Touchpad
(shown without swing-down front door)
IMP OR TANT!
• When entering codes and commands, sequential key depressions must be made
within 10 seconds of one another. If 10 seconds elapse without a key
depression, the entry will be aborted and must be repeated from its beginning.
Be sure to observe this precaution when performing any of the procedures in
this manual.
•
If you make a m ista k e while entering a security code, stop, press the [✱] key,
and then start over. If you stop in the middle while entering a code, and then
immediately start the entry over, an erroneous code might be entered.
– 11 –
Download from Www.Somanuals.com. All Manuals Search And Download.
(QWU\ꢃ([LWꢀ'HOD\V
(QWU\ꢀ'HOD\
Entry Delays give you time to disarm the system when you re-enter through the
designated entrance door. You must disarm the system (simply enter your security
code) before the entry delay period ends, or an alarm will occur. The touchpad beeps
during the entry delay period, reminding you to disarm the system. There are two
entry delays (if programmed). The first is for your primary entrance and the second
can be used for a secondary entrance, where a longer delay is required to walk to the
touchpad to disarm the system.
You can also arm the system with no entry delay at all by using the INSTANT
arming mode. This mode provides greater security while on the premises or while
away for extended periods of time.
See your installer for your delay times.
P a r tition 1 ___________________________________________________________
Exit Delay:
seconds
Entry Delay 1:
Entry Delay 2:
seconds
seconds
NOTE: Entry/Exit times set for partition 1 also apply to the common zone.
P a r tition 2 ___________________________________________________________
Exit Delay:
seconds
Entry Delay 1:
Entry Delay 2:
seconds
seconds
([LWꢀ'HOD\
E xit d ela y gives you time to leave through the designated exit door without setting
off an alarm. Exit delay begins immediately after arming your system in any arming
mode and Custom Display touchpads display the message “You May Exit Now.” When
“You may exit now” disappears, the system is fully armed. If programmed, a slow beeping
will sound during the exit delay period, until the last 10 seconds, which then changes
to fast beeping (alerting you to the end of exit delay). If you cannot leave by this time,
you should stop, disarm the system, and start over to avoid a false alarm.
E xit Dela y R esta r t (if programmed): If you wish to open the entry/exit door to let
someone in after arming STAY, you can re-start the exit delay at any time – sim p ly
p r ess th e [✱] k ey, then let that person in. The system automatically re-arms when
exit delay expires, which avoids having to disarm the system and then re-arm it
again. In addition, when the system is armed AWAY, reopening and closing the
entry/exit door before exit delay time expires (e.g., reentering to get a forgotten item)
will reset the exit delay time.
– 12 –
Download from Www.Somanuals.com. All Manuals Search And Download.
(QWU\ꢃ([LWꢀ'HOD\Vꢀꢁ&RQWLQXHGꢂ
([LWꢀ$ODUPV
Whenever you arm the system, the exit delay begins. If an entry/exit door or interior
zone is faulted when the exit delay ends (e.g., exit door left open), the system sounds
an alarm and starts the entry delay timer. If you disarm the system before the entry
delay ends, the alarm sound stops and the message "CANCELED ALARM" or "CA" is
displayed on the touchpad, along with a zone number indicating the faulted zone. No
message is sent to the Customer Care Center.
To clea r th e exit a la r m con d ition , the open zone must be made intact; to clear the
display, enter your code plus OFF.
If you do not disarm the system before the entry delay ends, and an entry/exit door or
interior zone is still open, the alarm sound continues and an "exit alarm" message is
sent to the Customer Care Center. The message ""EXIT ALARM" or "EA" is displayed
on the touchpad, along with a zone number indicating the faulted zone. To stop the
alarm, the system must be disarmed (your code plus OFF); to clear the display, enter
your code plus OFF a second time.
An “exit alarm” also results if an entry/exit door or interior zone is faulted within two
minutes after the end of the exit delay.
Your system may have been programmed for this feature to minimize false alarms sent to the Customer
Care Center. Ask your installer if "Exit Alarm" is active in your system. If so, check this box.
– 13 –
Download from Www.Somanuals.com. All Manuals Search And Download.
&KHFNLQJꢀ)RUꢀ2SHQꢀ=RQHV
8VLQJꢀWKHꢀ>∗@ꢀ.H\ꢀWRꢀ'LVSOD\ꢀDQGꢀ$QQRXQFHꢀ6\VWHPꢀ6WDWXV
Before arming your system, all protected doors, windows and other protection zones
must be closed or bypassed, otherwise the touchpad will display a "Not Ready" message.
1. Press [∗] READY (do not enter code first) to display
Custom Display:
faulted zones.
∗
2. Secure or bypass the zones displayed.
3. The touchpad’s READY indicator lights when all
protection zones have been either closed or bypassed.
4. Arm the system as desired.
English Display:
Zone no. and “NOT READY”
Voice Sta tu s: Voice Touchpads (if installed), can announce system status and faulted
zones (up to 3 zone descriptors) if the Voice Status feature is turned on.
To tu r n th e Voice Sta tu s fea tu r e on /off:
#
+
0
+
2
+
4
(also turns on Voice Chime mode; see Chime mode section)
To a n n ou n ce Sta tu s: Press [∗] STATUS key once.
To a n n ou n ce fa u lted zon es: Press the [∗] STATUS key a second time within 5
seconds of the first press.
– 14 –
Download from Www.Somanuals.com. All Manuals Search And Download.
$UPLQJꢀWKHꢀ6\VWHP
6WD\ꢀ0RGHꢁꢀ$UPVꢀ3HULPHWHUꢀ2QO\ꢂꢀ(QWU\ꢀ'HOD\ꢀ2Q
• Used when you want to arm the system with persons staying inside (or if you have
pets that are moving throughout the premises).
• The perimeter sensors are armed, but interior sensors are left disarmed.
• Exit delay begins (you can leave through the entry/exit door, if desired).
• An alarm sounds immediately if any protected perimeter window or non-entry/exit
door is opened.
• You may otherwise move freely within the premises.
• Persons entering later can enter through an entry/exit door without causing an
alarm, but they must disarm the system within the entry delay period to avoid
sounding an alarm.
1LJKWꢃ6WD\ꢀ0RGHꢁꢀ$UPVꢀ3HULPHWHUꢀ2QO\ꢂꢀ3OXVꢀ6HOHFWHGꢀ=RQHV
• Use Night-Stay mode to provide increased security while staying inside.
• Arms same as Stay mode, but also arms pre-selected interior sensors (programmed
by your installer), while other interior sensors are left disarmed.
• Persons entering later can use an entry/exit door but they must disarm the system
a n d must not violate any of the programmed interior zones to avoid sounding an
alarm.
• IMP OR TANT: When Night-Stay mode is on, the selected interior zones are armed
and cause an alarm if anyone enters those areas (e.g., waking in the middle of the
night). To avoid sounding an alarm, you must disarm the system before any
activity takes place in those interior zones.
,QVWDQWꢀ0RGHꢁꢀ$UPVꢀ3HULPHWHUꢀ2QO\ꢂꢀ(QWU\ꢀ'HOD\ꢀ2II
• Used when staying inside and do not expect anyone to use an entry/exit door.
• Arms same as Stay mode.
• An alarm sounds immediately if any protected perimeter window or any door is
opened, including entry/exit doors.
• IMP OR TANT: Arming the system in this mode greatly increases the chance of
false alarms. Use extreme care in selecting this mode of arming.
$ZD\ꢀ0RGHꢁꢀ$UPVꢀ(QWLUHꢀ6\VWHPꢂꢀ(QWU\ꢀ'HOD\ꢀ2Q
• Used when nobody will be staying inside (including pets).
• The entire system (interior and perimeter) is armed.
• Exit delay begins letting you leave through the entry/exit door.
• An alarm sounds if a protected window or any door is opened, or if any movement
is detected inside your premises.
• You can reenter through an entry/exit door without causing an alarm, but you
must disarm the system within the entry delay period to avoid sounding an alarm.
– 15 –
Download from Www.Somanuals.com. All Manuals Search And Download.
$UPLQJꢀWKHꢀ6\VWHP
$UPLQJꢀ&RPPDQGV
Before arming, close all perimeter doors and windows and make sure the Ready to Arm
message is displayed.
Mod es of Ar m in g
Mod e
Stay
P r ess th ese k eys…
security code + [3] (STAY)
Tou ch p a d Con fir m s By…
• three beeps
• armed STAY message displayed
• red ARMED indicator lights
• three beeps
Night-Stay security code + [3] + [3]
• NIGHT-STAY message displayed
• red ARMED indicator lights
• three beeps
• armed STAY message displayed
• red ARMED indicator lights
• also note that entry delay is turned off
Instant
Away
security code + [7] (INSTANT)
security code + [2] (AWAY)
• two beeps, or, if programmed, beeping
for duration of exit delay
• armed AWAY message displayed
• red ARMED indicator lights
Leave the premises through an entry/exit
door during the exit delay period to avoid
causing an alarm. The touchpad beeps
rapidly during the last 5 seconds of the
exit delay to warn you that it is ending.
Qu ick Ar m in g
If "Quick Arming" was programmed by the installer, the [#] key can be pressed in
place of the security code when arming the system in any of its arming modes.
However, th e secu r ity cod e m u st a lw a ys be u sed to d isa r m th e system .
F u n ction Key Ar m in g
For any arming command, a function key may have also been programmed for your system. If
so, you can press and hold the appropriate function key for 2 seconds to arm the system. See
your installer for the designated functions (see Sin gle Bu tton Ar m in g section).
Refer to the Accessin g Oth er P a r tition s section for information on multi-partiion
arming.
– 16 –
Download from Www.Somanuals.com. All Manuals Search And Download.
$UPLQJꢀWKHꢀ6\VWHP
6LQJOHꢀ%XWWRQꢀ$UPLQJ
The “A”, “B”, “C”, and/or “D” keys on your touchpad may have been programmed for
single-button arming. Note that while it will not be necessary to use a security code
for arming, a security code must always be used to disarm the system.
If Single-Button Arming is programmed:
• A function key has been assigned to a specific type of arming: STAY mode, Night-
STAY mode, AWAY mode, or STEP-ARMING (see Step-Arming paragraph).
• You DO NOT need to enter your security code before pressing the function key
(but you always need your security code to DISARM the system).
Before arming, close all perimeter doors and windows.
1. Press and hold the assigned function key for 2
seconds (no code is required). Function keys are
shown below.
OFF
AWAY
TEST
CODE
STAY
A
B
C
D
1
4
7
2
5
8
0
3
6
9
#
English Display: Green LED lit
BYPASS
INSTANT
READY
CHECK
ADT3000-007-V0
*
2. The touchpad begins beeping and displays the
armed message. The red ARMED indicator also
lights.
English Display: AWAY
6LQJOHꢃ%XWWRQꢀ´6WHSµꢀ$UPLQJ
Single-Button “Step” arming may have been programmed into one of the lettered keys
(A, B, C, or D). Check with your installer to see if this has been done in your system.
If Step-Arming is programmed:
• The assigned key provides a choice of three levels of security.
• The selected key can be pressed once, twice, or three times, increasing the level of
security with each press, as follows
Key
Ø
F ir st P r ess
Ø
Secon d P r ess
Ø
Th ir d P r ess
Ø
Armed-STAY
Armed Night-STAY
(if programmed)
Armed-AWAY
A, B, C, D
– 17 –
Download from Www.Somanuals.com. All Manuals Search And Download.
8VLQJꢀWKHꢀ.H\VZLWFK
8VLQJꢀWKHꢀ.H\VZLWFK
Your system may be equipped with a keyswitch for use when arming and disarming.
Red and green lights on the keyswitch plate indicate the status of your system as
follows:
Gr een Ligh t: Lights when the system is d isa r m ed a n d r ea d y to be armed (no
open zones). If the system is disarmed and the green light is off, it
indicates the system is not ready (one or more zones are open).
R ed Ligh t:
Lights or flashes when system is armed in AWAY or STAY mode.
See your installer for the meanings of the lit red light:
Lit Steady = system armed AWAY or
system armed STAY and exit delay has expired
Flashing = system armed STAY and exit delay timer active
Rapid flashing = an alarm has occurred (memory of alarm).
Before arming, close all perimeter doors and windows.
To a r m in th e AWAY m od e:
Turn the key to the right for 1/2 second and release.
Touchpads beep twice and the red indicator lights or
flashes.
GREEN
RED
To a r m in th e STAY m od e:
Turn the key to the right and hold for longer than 1
second, then release. Touchpads beep three times
and the red indicator lights or flashes.
To d isa r m th e system :
Turn the key to the right and release. The red light
turns off
– 18 –
Download from Www.Somanuals.com. All Manuals Search And Download.
'LVDUPLQJꢀDQGꢀ6LOHQFLQJꢀ$ODUPV
8VLQJꢀWKHꢀ>2))@ꢀNH\
The OF F key is used to disarm the system, silence alarm and trouble sounds, and
clear alarm memories.
IMP ORTANT: If you r etu r n a n d th e m a in bu r gla r y sou n d er is on , DO NOT ENTER, but
CONTACT THE POLICE from a nearby safe location.
If you return after an alarm has occurred and the main sounder has shut itself off, th e tou ch p a d
w ill b eep r a p id ly u p on you r en ter in g, in d ica tin g th a t a n a la r m h a s occu r r ed d u r in g you r
a bsen ce.
LEAVE AT ONCE, and CONTACT THE POLICE from a nearby safe location.
1.
+
1
(Security Code)
OFF
The “READY” indicator light will be lit if all zones
are secure, and the touchpad will emit a single tone
to confirm that the system is disarmed.
READY
English Display:
NOTE: If entry delay has started (you’ve opened the
entry door), you do not need to press the OFF key;
simply enter your security code.
2. To Silence a Burglary Alarm and Clear a Memory of Alarm
Enter your security code. This disarms the system and silences the alarm (or
warning tones of a Memory of Alarm).
Note the zone in alarm on the touchpad display, and make that zone intact (close
door, window, etc.). Now enter the security code plus OFF sequence again to clear
the touchpad’s Memory of Alarm display.
3. To Silence a Fire Alarm and Clear Memory of Alarm
Simply press the OFF key to silence the alarm. Note the zone in alarm on the
touchpad display, and check the detector. Now enter the security code plus OFF
sequence to clear the touchpad's Memory of Alarm display. See the Fire Alarm
System section.
– 19 –
Download from Www.Somanuals.com. All Manuals Search And Download.
%\SDVVLQJꢀ3URWHFWLRQꢀ=RQHV
8VLQJꢀWKHꢀ%<3$66ꢀ.H\
Use this key when you want to arm your system with one or more zones intentionally
unprotected.
Ven t Zon es: Your system may have certain windows set as “vent” zones, which are
automatically bypassed if left open when arming the system (you do not need to
manually bypass them). However, if a vent zone window is closed a fter arming, it
becomes protected and will cause an alarm if opened again while the system is armed.
When bypassing zones:
• The system must be disarmed before you can bypass zones.
• Bypassed zones are unprotected and will not cause an alarm if violated.
• The system will not allow fire zones to be bypassed.
• Zones are automatically unbypassed when the system is disarmed.
1.
+
6 + zone numbers (see below)
(Security Code)
BYPASS
Enter the 2-digit zone number(s) for the zone(s) to be
bypassed (e.g., 06, 10, 13, etc.). Single digit zone
numbers must be preceded by a zero (e.g. 05, 06).
English Display: NOT READY
2. When finished, the touchpad will momentarily
display a "Bypass" message for each bypassed zone
number. Wait for all bypassed zones to be displayed.
Arm the system as usual.
English Display: BYPASS
To display bypassed zones prior to arming, enter
your security code and press the [6] BYPASS key.
– 20 –
Download from Www.Somanuals.com. All Manuals Search And Download.
%\SDVVLQJꢀ3URWHFWLRQꢀ=RQHV
4XLFNꢀ%\SDVV
If programmed, "Quick Bypass" allows you to easily bypass all open (faulted) zones
without having to enter zone numbers individually. This feature is useful if, for
example, you routinely leave certain windows open when arming at night.
1.
+
6 + [#]
(Security Code)
BYPASS
In a few moments, all open zones will be displayed
and automatically bypassed. Make sure that only those
zones that you wish to leave unprotected are bypassed, and
that there are no other zones unintentionally left open.
NOT READY
English Display:
2. Wait for all bypassed zones to be displayed, then arm
the system as desired.
Ask your installer if "Quick Bypass" is active for your
system, and if so, check here:
BYPASS
English Display:
– 21 –
Download from Www.Somanuals.com. All Manuals Search And Download.
&KLPHꢀ0RGH
CHIME mode alerts you to the opening of a perimeter door or window while the
system is disarmed. When Chime mode is activated:
• Three tones sound at the touchpad whenever a perimeter door or window is opened.
• Interior zones do not produce a tone when they are faulted.
• Pressing the READY key will display the open protection points.
To tu r n Ch im e Mod e on /off (system must be disarmed):
+
9
(Security Code)
CHIME
READY
English Display:
The CHIME message appears when on. Perimeter
zones will cause a tone when faulted.
The CHIME message disappears when Chime mode
is off.
English Display: CHIME
Voice Ch im e: You can set the Voice Touchpads (if installed) to announce faulted
(opened) entry/exit or perimeter zones whenever normal Chime mode is on.
To tu r n Voice Ch im e Mod e on or off:
#
+
0
+
2
+
4
(normal Chime mode must be on first)
When Voice Chime is on, any faulted zone(s) causes a voice status announcement,
chime and display. When off, the sounder still provides chime if normal Chime
mode is on.
– 22 –
Download from Www.Somanuals.com. All Manuals Search And Download.
9LHZLQJꢀ&XUUHQWꢀ'DWHꢀDQGꢀ7LPH
9LHZLQJꢀWKHꢀ&XUUHQWꢀ'DWHꢀDQGꢀ7LPH
The system lets you view its time and date setting.
+[#] + [6] [3]
(Security Code)
OR, press the function key (A, B, C, or D) for viewing
current date and time, if programmed.
English Display: READY
A typical time/date display is shown.
The display will remain on for about 30 seconds.
“A”
“B ”
“C ”
“D ”
If one of the above keys has been programmed for the date/time
display feature, place a check mark in the box beneath that key.
6HWWLQJꢀWKHꢀ'DWHꢀDQGꢀ7LPH
You can set the time and date by doing the following:
1. +[#] + [6] [3]
(Security Code)
2. Press [∗] when the time/date is displayed.
A cursor appears under the first digit of the hour.
To move cursor ahead, press [∗]. To go back, press [#].
• Enter the 2-digit hour setting.
Current time display
• Enter the 2-digit minute setting.
• Press [1] for PM or [0] for AM.
• Enter the last two digits of the current year.
• Enter the 2-digit month setting.
• Enter the 2-digit day setting.
Time/date editing display
3. To exit, press [∗] when cursor is at the last digit, or
wait 10 seconds.
– 23 –
Download from Www.Somanuals.com. All Manuals Search And Download.
3DQLFꢀ.H\V
8VLQJꢀ3DQLFꢀ.H\V
Your system may have been programmed to use special keys to manually activate
emergency (panic) functions as follows:
Th is F u n ction
Sen d s th is sign a l*
With Th is Sou n d in g…
Silent Alarm
silent alarm
no audible alarm or any visual display
indicating that a silent alarm has been
initiated.
Audible Alarm
audible alarm
a loud, steady alarm at touchpad(s)
and at any external sounders that
may be connected.
Personal Alarm
Fire Alarm
auxiliary alarm
fire alarm
steady alarm sound at touchpad(s),
but not at external bells or sirens.
temporal (pulsing) sound at external
bells and sirens.
*All panic functions send signals to the Customer Care Center, if connected.
To a ctiva te a P a n ic F u n ction :
Press and hold down for at least 2 seconds whichever
lettered key on the touchpad has been programmed for
the desired emergency function.
English Display: READY
OR
Typical Panic Display:
Press both keys of the assigned key pair at the same
time.
English Display:
99 and ALARM
PRESS BOTH KEYS
OF DESIRED PAIR
AT THE SAME TIME
OFF
2
5
8
0
AWA
Y
3
6
9
ST
A
Y
1
4
7
TEST
BYPASS
CHIME
ZONE 95
ZONE 96
INSTANT
READY
CODE
A
B
C
D
#
OFF
AWA
Y
ST
A
Y
1
4
7
2
5
8
0
3
6
9
TEST
BYPASS
CHIME
INSTANT
READY
CODE
#
ZONE 99
Lettered Panic Keys
Panic Key Pairs
See your installer and use the chart provided in the Fea tu r es P r ogr a m m ed in You r
System section to note the functions that have been programmed for your system.
– 24 –
Download from Www.Somanuals.com. All Manuals Search And Download.
0DFURꢀ.H\ꢀ3URJUDPPLQJꢀ ꢀ8VDJH
$ERXWꢀ0DFURꢀ.H\V
The “A”, “B”, “C” or “D” keys can be used to automatically activate a series of
commands of up to 16 keystrokes, if programmed for this function. These keystrokes,
as a group, are called “macros” and are stored in the system's memory.
• Typical macro functions can include:
- Arming sequences: STAY, Night-STAY, INSTANT, or AWAY
- Bypassing particular zone(s)
- Activating relay(s) for turning on (or off) lights, fans, etc.
• Up to four macros can be assigned – but no more than one macro to a key.
• Macros can be activated only by users with authority levels authorized to
perform the macro’s function.
NOTE: The installer must activate the desired function key (using *57 Function key
Menu Mode) before macros can be assigned.
See the chart at the back of this manual for the key(s) assigned for macros.
1.
+ [#] + [6] + [6]
(Security Code)
2. Enter the macro number, 1-4, to be programmed at
the “Select Macro?” prompt. Remember, there are
four macros available, but only one macro can be
assigned to each key.
3. If a macro has been previously defined, the
keystrokes are shown on the bottom line of the
display, otherwise the display is blank.
To exit this mode (and keep the existing macro
definition), press any key except the [∗] key. The
system returns to normal mode.
To define a macro for the selected key, press [∗] and
continue with the next prompt.
Enter the first of the series of desired commands, (do
not include your user code when programming a
macro), then press/hold the “D” key for at least two
seconds to complete the first command. This key
terminates each separate command, and appears as
an “F” in the touchpad display.
– 25 –
Download from Www.Somanuals.com. All Manuals Search And Download.
0DFURꢀ.H\ꢀ3URJUDPPLQJꢀ ꢀ8VDJHꢀꢁFRQWꢄꢂ
Typical Macro Display:
The touchpad beeps to acknowledge your input and
displays the command you entered (followed by “F”).
4. Enter the next command, followed by press/holding
ꢀ ꢁ ꢂ ꢁ ꢃ * # ꢄ ꢁ ꢅ * ꢂ *
the “D” key for at least two seconds. The touchpad
beeps and displays the keystrokes entered so far.
5. Repeat until the all the desired commands (up to 16
characters including the “F”s) have been entered.
Be sure to check your keystrokes before continuing.
If you made a mistake, you must start over.
6. To exit, press/hold the “D” key for at least two
seconds. The display returns to system status and
indicates system is ready.
([DPSOHꢀRIꢀ0DFURꢀ3URJUDPPLQJ
Suppose you want to (1) bypass the two upstairs window zones, then (2) turn on an
exterior light, and then (3) arm the security system in the AWAY mode. The
procedures in the table that follows show you how you would program this macro:
Function
Keystrokes Required
Touchpad Display
1. Bypass zones 02 & 03
Press BYPASS [6] key, then
ꢀ ꢁ ꢂ ꢁ ꢃ
2-digit zone numbers 02 & 03.
Press the “D” key for at least 2 seconds.
2. Insert terminator.
ꢀ ꢁ ꢂ ꢁ ꢃ *
3. Turn light on
(device 01).
Press [#] and 7 keys for “device ON”, and
[01] key for selecting device 1.
ꢀ ꢁ ꢂ ꢁ ꢃ * ꢄ ꢁ ꢅ
#
4. Insert terminator.
Press the “D” key for at least 2 seconds.
ꢀ ꢁ ꢂ ꢁ ꢃ * # ꢄ ꢁ ꢅ *
ꢀ ꢁ ꢂ ꢁ ꢃ * # ꢄ ꢁ ꢅ * ꢂ
ꢀ ꢁ ꢂ ꢁ ꢃ * # ꢄ ꢁ ꢅ * ꢂ *
5. Arm system AWAY
6. Insert terminator.
Press AWAY [2] key.
Press the “D” key for at least 2 seconds.
8VLQJꢀDꢀ3URJUDPPHGꢀ0DFURꢀ.H\
Press the Macro key programmed for the desired
1.
series of commands for at least 2 seconds. The “Enter
User Code” prompt appears. The prompt remains
displayed for up to 10 seconds.
2. Enter your 4-digit user code.
The programmed macro sequence begins
automatically after the user code is entered.
– 26 –
Download from Www.Somanuals.com. All Manuals Search And Download.
8VLQJꢀ'HYLFHꢀ&RPPDQGV
$ERXWꢀ'HYLFHꢀ&RPPDQGV
Your system may be set up so that it can control certain lights or other devices.
• Some devices may be automatically turned on or off by the system.
• You may be able to override automatically controlled devices using the
commands described below.
• Some devices can be manually turned on or off using the commands described
below.
• See your installer for a list of devices that may be set up for your system. A list
of these devices is provided at the back of this manual for you to fill out.
To Activa te Devices:
+ [#] + [7] + 2-digit device number
(Security Code)
English Display: READY
Devices associated with that device number activate.
To Dea ctiva te Devices:
+ [#] + [8] + 2-digit device number
(Security Code)
Devices associated with that device number deactivate.
– 27 –
Download from Www.Somanuals.com. All Manuals Search And Download.
3DJLQJꢀ)HDWXUH
$ERXWꢀ$XWRPDWLFꢀ3DJLQJ
Your system may be set up to automatically send alert messages to a pager as certain
conditions occur in your system.
• The following events can be programmed by your installer to be sent to the pagers:
arming, disarming†, alarms, and trouble conditions. († reports when arming/disarming
from a touchpad using a security code; auto-arming/disarming, arming with assigned
button, and keyswitch arming do not send pager messages.)
• You can also program the system to send an automatic pager message to alert you
in the event that someone has not arrived home (disarmed the system) within a
defined period of time (see the Sch ed u lin g section for details on programming a
“latch key report”).
• Your installer programs the pager phone numbers and reporting events.
• The pager message consists of a 7-digit system status code that indicates the type of
condition that has occurred.
• An optional, predefined 16-digit character string can precede the 7-digit system
status code; these characters can consist of a PIN no., subscriber account no., or any
additional data that you may wish to have sent to the pager.
• The pager display format is as follows:
3-digit Event Code
Optional 16 digits AAAAAAAAAAAAAAAA – BBB – CCCC 4-digit User or Zone No.
A =
B =
C =
A 4-digit User or Zone number, depending on the type of
event that has occurred, where:
Optional 16-digits for A 3-digit code that
Account numbers,
PIN numbers, or any
other data;
describes the event
that has occurred
in your system
• alarms and troubles display zone number
• arming/disarming (opens/closes) display user number
The first digit indicates partition (0 = system, 1 =
partition 1, 2 = partition 2, 3 = common), followed by the
3-digit user or zone number.
programmed by the
installer, if required.
(see for event
codes table below)
The 3-digit Event Codes (BBB) that can be displayed are:
911 =
811 =
101 =
102 =
Ala r m s.
Tr ou bles.
Op en
Close
(syst em d isa r m ed ).
(syst em a r m ed ).
The 4-digit number
The 4-digit number
(CCCC) following this
code is the zone number code is the zone number
that has caused the
alarm.
(CCCC) following this
The 4-digit number
(CCCC) that follows
this code is the user
number that has
The 4-digit number
(CCCC) that follows
this code is the user
number that has armed
the system.
that has caused the
trouble.
disarmed the system.
– 28 –
Download from Www.Somanuals.com. All Manuals Search And Download.
3DJLQJꢀ)HDWXUH
Examples of typical 7-digit pager displays follow.
Ex. 1.
= R eporting of an alarm (911) caused by a fault on zone 4 (0004) in
= Reporting of a closing–system arming (102)– by user 5 (0005) in
partition 1.
partition 2.
Ex. 2.
$ERXWꢀ0DQXDOꢀ3DJLQJ
Your system may be set up so you can manually send a message to up to four pagers.
• Your installer programs the paging function key and the pager phone numbers.
• Pressing the paging keys sends the message 9 9 9 – 9 9 9 9
to the selected pager.
• This message could mean “call home”, “call your office”, or any other prearranged
meaning.
• See the Paging chart at the back of this manual for details of the paging setup for
your system.
1. Hold pager key 2 seconds then press [1-4].
(pager no.)
Press and hold the programmed Paging Key for at
least 2 seconds (wait for beep), then press the pager
number (1-4)* representing the pager intended to
receive the message.
English Display: READY
2. The recipient, on seeing the 999–9999 message, will
understand the prearranged meaning of this signal.
Pager Display
* If no number is pressed, the message is sent to pager 1.
/DWFKꢀ.H\ꢀ3DJLQJ
You can program a schedule that causes a pager report to be sent if the system is not
DISARMED by the scheduled time (see Sch ed u lin g section, event “03”). For example,
a working parent might want a message to be sent to a pager if their child did not
arrive home from school and disarm the system by a certain time.
If programmed, the message that is sent is: 7 7 7 – 7 7 7 7
.
– 29 –
Download from Www.Somanuals.com. All Manuals Search And Download.
6HFXULW\ꢀ&RGHVꢀ ꢀ$XWKRULW\ꢀ/HYHOV
$ERXWꢀ6HFXULW\ꢀ&RGHV
Your system lets you assign up to 45 different security codes for use by other users.
• Only the System Master and Partition Masters can assign user codes to users.
• Users are identified by 2-digit user numbers 03-49 and are pre-assigned to either
partition 1 or partition 2 (users 01-02 are reserved).
• Only the Installer or System Master can change the partitions to which a user is assigned.
• In addition to a security code, each user is assigned various system attributes.
• User codes can be used interchangeably within a partition when performing system
functions (a system armed with one user's code can be disarmed by another user's
code), with the exception of the guest code described below.
• User code programming involves these steps:
1. Choose a user number from the set of users assigned to the partition in which the
user will be operating, and assign a 4-digit security code.
2. Assign an authority level to that user.
3. Assign other attributes as necessary (see attributes on the next page).
NOTE: The factory settings are designed to meet most normal user situations.
Therefore, the only step you usually need to do when adding users is assign a user
number (from the partition’s pre-assigned user numbers) and a security code.
$XWKRULW\ꢀ/HYHOꢀ'HILQLWLRQV
Authority levels define the system functions a particular user can/cannot perform.
Level Title
Exp la n a tion
N/A
System Master
Reserved for user 02; Can perform all system functions and assign
codes in both partitions; can change its own code as follows:
Master code + [8] + 02 + new master code + new master code again
0
Standard User
Can only perform security functions in assigned partition.
Cannot perform other system functions.
1
2
Arm Only
Guest
Can only arm the system. Cannot disarm or do other functions.
Can arm the system in assigned partitions, but cannot disarm the
system u n less the system was armed with this code. This code is
typically assigned to someone (such as a babysitter or cleaner) who
has a need to arm/disarm the system only at certain times. The user
of this code should n ot use the “Quick Arming” feature.
3
4
Duress Code
Intended for use when you are forced to disarm or arm the system
under threat. When used, the system will act normally, but can
silently notify the Customer Care Center of your situation, if that
service has been provided.
Partition Master Can do everything a standard user can do, and can assign
user codes to users in their partition.
– 30 –
Download from Www.Somanuals.com. All Manuals Search And Download.
6HFXULW\ꢀ&RGHVꢀ ꢀ$XWKRULW\ꢀ/HYHOVꢀꢁ&RQWꢄꢂ
+RZꢀ7Rꢀ$VVLJQꢀ8VHUꢀ&RGHVꢀDQGꢀ$WWULEXWHV
The following lists the various command strings for adding user codes and attributes.
R efer to th e User Setu p ch a r t a t t h e b a ck of th is m a n u a l for fa ctor y
a ssign m en ts of u ser a ttr ib u tes a n d to k eep a r ecor d of u ser p r ogr a m m in g.
NOTE: Partition Master codes apply only to those user numbers previously assigned
(by the system master/installer) to the partition master’s partition.
Ad d User Cod e:
System/Partition Master code + [8] + user no. + new user’s code
(Users 03/33 are preset
to partition masters,
but can be changed.)
User 01 = installer
User 02 = master
The Touchpad beeps once to confirm that new user was added.
User 03 = partition 1 master
User 33 = partition 2 master
Delete User Cod e:
System/Partition Master code + [8] + [user no.] + [#] [0]
The user code and all attributes* programmed for this user number,
including any associated RF keys, are erased from the system.
(*except assigned partition)
Au th or ity Level:
System/Partition Master code + [8] + [user no.] + [#] [1]+ auth. level
Factory Assignments:
users 04-32/34-49 = 0
users 03/33 = 4
Authority Levels (see definitions on previous page):
0 = standard user
1 = arm only
2 = guest
3 = duress
4 = partition master
Access Gr ou p :
System/Partition Master Code + [8] + [user no.] + [#] [2]+ group (1-8)
Factory Assignments: none
You can assign users to a group, then set an access schedule that
defines the times this group of users can operate the system. The
system ignores these users outside the scheduled times.
User ’s P a r tition :
System Master Code + [8] + [user no.] + [#] [3]+ 0 + partition(s) + [#]
Factory Assignments:
Part. 1 = users 03-32
Part. 2 = users 33-49
This command assigns the partitions the user can access. If more than
one, enter partition numbers sequentially, then press [#] to end.
E.g., master code + [8] + [user no.] + [#] [3] + [0] + [1] [2] + [#] gives
the user access to partitions 1 and 2 and the common partition.
Partition Entries: 1 = partition 1 and common
2 = partition 2 and common
3 = common partition only
R F User Nu m b er :
System/Partition Master Code + [8] + [user no.] + [#] [4]+ zone no.
Factory Assignments: none
Use this command to assign a wireless button device (keyfob) to this
user (keyfob must be enrolled in system first; see installer).
Zone number: enter the zone number assigned to a button on the
keyfob that will be used for arming/disarming by this user.
P a ger On /Off:
System/Partition Master Code + [8] + [user no.] + [#] [5] + 0 or 1
Factory Assignments:
users 01-04 = 0 (off)
users 05-49 = 1 (on)
You can program a user so that a message is sent to a pager
whenever this code is used to arm or disarm the system.
Paging On/Off: 1 = allow paging; 0 = no paging for this user
– 31 –
Download from Www.Somanuals.com. All Manuals Search And Download.
$FFHVVLQJꢀ2WKHUꢀ3DUWLWLRQV
ꢀꢁ*272ꢀ&RPPDQGꢀDQGꢀ0XOWLꢅ3DUWLWLRQꢀ$UPLQJꢂ
$ERXWꢀ$FFHVVLQJꢀ3DUWLWLRQV
Each touchpad is assigned a default partition for display purposes, and will show only
that partition's information.
• If the user is authorized, a touchpad in one partition can be used to perform
system functions in the other partition by using the GOTO command. Refer to
the GOTO section.
• If the user is authorized, that user can arm other partitions. Refer to the Multi-
Partition Arming section.
The following table shows the relationship of the touchpads in each partition when
system is armed and disarmed.
P ARTITION 1
P ARTITION 2
COMMON ZONE
(LOBBY, etc.)
Ar m in g
Sta te
Tou ch p a d
Sta tu s
Ar m in g
Sta te
Tou ch p a d
Sta tu s
Ar m in g
Sta te
Tou ch p a d
Sta tu s
Disarmed
Partition 1
Disarmed
Partition 2
Disarmed Common Zone
Con d it ion 1
Ö
On ly
On ly
On ly
Disarmed Partition 1 and
Common Zone
Armed
Partition 2
Disarmed Common Zone
Con d it ion 2 Ö
Con d it ion 3 Ö
On ly
On ly
Armed
Partition 1
Disarmed Partition 2 and Disarmed Common Zone
On ly
Common Zone
On ly
Armed
Partition 1
Armed
Partition 2
Armed
Common Zone
Con d it ion 4 Ö
On ly
On ly
On ly
When both partitions are disarmed, the touchpad in each partition displays zone
status for its partition only. The common zone touchpad shows the status in that
zone only. See Condition 1 above.
When partition 1 is disarmed and partition 2 is armed, the touchpad in partition 1
shows the status of partition 1 a n d the common zone. Partition 2 will display the
status of partition 2 on ly. See Condition 2 above.
When partition 1 is armed and partition 2 is disarmed, the touchpad in partition 1
shows the status of partition 1 on ly. Partition 2 will display the status of partition
2 a n d the common zone. See Condition 3 above.
As long as any one of the two partitions is disarmed, the common zone will always
be disarmed. The common zone will be armed only when both partition 1 and 2 are
armed. See Condition 4 above.
– 32 –
Download from Www.Somanuals.com. All Manuals Search And Download.
$FFHVVLQJꢀ2WKHUꢀ3DUWLWLRQVꢀꢁ&RQWLQXHGꢂ
8VLQJꢀWKHꢀ*R7Rꢀ&RPPDQG
If the user is authorized, a touchpad in one partition can be used to perform system
functions in the other partition by using the GOTO command.
• You must use a Custom English touchpad to access another partition.
• Touchpads automatically return to their original partition after 2 minutes
with no touchpad activity.
1.
+ [∗] + partition number (0,1,2,3)
(Security Code)
0 = return to touchpad’s original partition.
English Display: Green LED lit
1 = partition 1; 2 = partition 2; 3 = common zone
The touchpad beeps to confirm the partition change.
2. The touchpad remains in the new partition until
directed to go to another partition, or until it
automatically returns to the original partition.
The active partition number is displayed in the upper
left portion of screen, if the option is programmed.
English Display: Green LED lit
0XOWLꢃ3DUWLWLRQꢀ$UPLQJ
Some users can be given Multi-Partition arming ability by being assigned to both
partitions when programming user attributes.
When attempting to arm multi-partitions:
• You must use a Custom English touchpad.
• The system arms only if all partitions are “ready to arm.”
• If any partition is “not ready,” the system does not arm at all.
• You can use the GOTO command to bypass open zones before arming.
• If any partition is already armed when global arming is attempted, that
partition remains in its existing armed state.
+ [0] + arm command (see list below)
(Security Code)
Multi-Partition Arming Commands
English Display: Green LED lit
2 = arms all partitions AWAY
3 = arms all partitions STAY
33 = arms all partitions NIGHT-STAY
7 = arms all partitions INSTANT
1 = disarms all partitions
– 33 –
Download from Www.Somanuals.com. All Manuals Search And Download.
$FFHVVLQJꢀ2WKHUꢀ3DUWLWLRQVꢀꢁ&RQWLQXHGꢂ
&RPPRQꢀ=RQHꢀ2SHUDWLRQ
Your system may have been set up to use a common zone, which is
an area shared by users of both partitions, such as a foyer or lobby.
If so, please note the following:
Ask your installer if a
"common zone" was
assigned. If so, check
this box
•
The common zone will sound and report alarms only when b oth
partitions are armed. If only one partition is armed, the system
ignores faults on the common zone.
•
Either partition may arm its system if the common zone is
faulted, but once armed, the other partition w ill n ot be able to
arm unless the common zone is first bypassed or the fault is
corrected.
•
Faults on the common zone are displayed on common zone
touchpads, and will also appear on another partition’s touchpad
when that partition is armed.
•
•
Either partition can clear and restore the common zone after an
alarm.
Entry/exit time for the common zone is the same as for partition 1.
– 34 –
Download from Www.Somanuals.com. All Manuals Search And Download.
6FKHGXOLQJ
$ERXWꢀ6FKHGXOLQJ
The system provides up to 16 end-user schedules (programmable by master/installer
only), which can be used to control various types of events.
• Each schedule causes a defined event to start and stop (when appropriate) at a
specified time.
• Schedules can be set to automatically repeat at various intervals.
• Schedules can be set for random starting, if desired.
&UHDWLQJꢀ6FKHGXOHV
1.
+ [#] + [6] [4]
(Master Code)
2. Enter a 2-digit schedule number from 01-16.
Press [∗] to continue.
=
3. Enter the desired 2-digit event number from the
following list.
00 = clear the scheduled event
01 = turn a programmed output on or off
(see Usin g Device Com m a n d s section for a list of output device numbers used
in your system)
02 = set a user access schedule for one or more users
(see Secu r ity Cod es section for an explanation of access groups)
03 = send a “latch-key” report to a pager if the system is not disarmed by a specified
time; message sent is “777-7777.”
04 = automatically arm the system in STAY mode at a specified time
05 = automatically arm the system in AWAY mode at a specified time
06 = automatically disarm the system at a specified time
07 = Display the word “REMINDER” at a specified time
Press [∗] to continue.
4. For event number “01,” enter the output number
associated with this schedule.
Otherwise, this prompt is skipped.
Press [∗] to continue to the “Start” prompt below.
– 35 –
Download from Www.Somanuals.com. All Manuals Search And Download.
6FKHGXOLQJꢀꢁFRQWLQXHGꢂ
5. For event number “02,” enter the access group
number. Otherwise, this prompt is skipped.
Press [∗] to continue to the “Start” prompt below.
6. For event numbers “03-07,” enter the partition
number to be armed or disarmed.
0 = arm all; 1 = partition 1; 2 = partition 2;
3 = arm common
Otherwise, this prompt is skipped.
Press [∗] to continue to the “Start” prompt.
7. Enter the event’s start time and days of week.
Hour = 00-12; minute = 00-59
AM = 0; PM = 1
Days = Position the cursor under the desired days
using the [∗] key to move forward, then press “1” to
select the day.
Press [∗] to continue.
8. Enter the event’s stop time, AM/PM and days of week.
Refer to step 7 for available entries.
Press [∗] to continue.
9. Enter the desired repeat option.
0 = no repeat
1 = repeat schedule weekly
2 = repeat schedule biweekly (every other week)
3 = repeat schedule every third week
4 = repeat schedule every fourth week
e.g., To make a schedule that happens everyday you
would select all days with a repeat count of 1. To make
a schedule that runs for one week then stops, select
everyday with a repeat count of 0.
10. Select the randomize option, if desired.
0 = no; 1 = yes
=
=
If selected, the schedule times will vary within 60
minutes of the “hour” time. For example, if a
schedule is set to start at 6:15pm, it will do so the
first time 6:15pm arrives, but on subsequent days it
will start anytime between 6:00 and 6:59 p.m.
Press [∗] to continue.
– 36 –
Download from Www.Somanuals.com. All Manuals Search And Download.
(YHQWꢀ/RJJLQJꢀ3URFHGXUHV
$ERXWꢀ(YHQWꢀ/RJJLQJ
The system records various events in a history log, which can be viewed by the master
user using a Custom English Display touchpad.
• The Event Log holds up to 100 events.
• Events are displayed in chronological order, from most recent to oldest.
• When the log is full, the oldest event is replaced by the logging of any new event.
9LHZLQJꢀWKHꢀ(YHQWꢀ/RJ
1.
+ [#] +
6
+
0
(Master Code)
2. The system displays the most recent event as follows:
• event number
• type of event, identified by its corresponding code
(see your installer for the meaning of each code)
• zone or user number (depending on type of event)
• partition in which event occurred
• time and date of the event’s occurrence.
3. Pressing [∗] displays previous events (back in time).
Pressing [#] displays events forward in time.
4. Exit the event log by pressing any key other than [∗]
or [#].
– 37 –
Download from Www.Somanuals.com. All Manuals Search And Download.
(YHQWꢀ/RJJLQJꢀ3URFHGXUHVꢀꢁFRQWLQXHGꢂ
7DEOHꢀRIꢀ(YHQWꢀ/RJꢀ&RGHV
The following table lists the codes that may appear when viewing the Event Log.
If the event code is preceded by an “E” (as in the example display on the previous
page), it means that the event is new and ongoing; if preceded by an “R,” it means the
event has been restored.
Code
110
121
122
123
Definition
Fire Alarm
Duress
Alarm, 24-hour Silent
Alarm, 24-hour Audible
Code
Definition
381
382
383
384
393
401
RF Supervision Trouble
Supervision Auxiliary Wire Zone
RF Sensor Tamper
RF Sensor Low-battery
Clean Me
Disarmed, Armed AWAY,
Armed STAY
Schedule Arm/Disarm AWAY
Cancel by User
Remote Arm/Disarm
(Downloading)
Quick Arm AWAY
Keyswitch Arm/Disarm AWAY
Disarmed/Armed
STAY/INSTANT,
Quick-Arm STAY/INSTANT
Keyswitch Arm/Disarm STAY
Bypass
Manually Triggered Dialer Test
Periodic Test
AAV to Follow
Walk Test Entered/Exited
Event Log 80% Full
131
132
134
135
Alarm, Perimeter
Alarm, Interior
Alarm, Entry/Exit
Alarm, Day/Night
403
406
407
143
145
146
150
Alarm, Expansion Module
ECP Module cover tamper
Silent Burglary
Alarm, 24-Hour Auxiliary/Monitor
zone
Carbon Monoxide
AC Power
Low System Battery/Battery Test
Fail
System Reset (Log only)
Battery Test Failure
Bell/Siren Trouble
Trouble, Expansion Mod.
Supervision
Trouble, ECP Cover Tamper
RF Receiver Jam
Telco Line Fault
408
409
441
162
301
302
442
570
601
602
606
607
623
625
305
309
321
333
Real-Time Clock was Changed
(log only)
341
344
351
353
373
374
380
627
628
750 -
789
Program Mode Entry (log only)
Program Mode Exit (log only)
Reserved for Configurable Zone
Type report codes (check with
central station when using these
codes)
Long Range Radio Trouble
Fire Loop Trouble
Exit Error Alarm
Global Trouble, Trouble
Day/Night
– 38 –
Download from Www.Somanuals.com. All Manuals Search And Download.
7HVWLQJꢀWKHꢀ6\VWHPꢀꢁ7Rꢀ%Hꢀ&RQGXFWHGꢀ:HHNO\ꢂ
$ERXWꢀ7HVWLQJꢀWKHꢀ6\VWHP
Using TE ST mode allows each protection point to be checked for proper operation.
• The touchpad sounds a single beep every 40 seconds as a reminder that the
system is in the Test mode.
• Alarm messages are not sent to your Customer Care Center while Test mode is on.
1 Disarm the system and close all protected windows,
doors, etc. The READY indicator light should come
on if all zones are intact (i.e., all protected windows,
doors, etc. are closed.
2.
+
5
then [0] (walk)
=
=
(Security Code)
TEST
The Dial test (option “1”) is intended for the installer
and should not be used unless directed to do so by
your Customer Care Representative.
3. Listen. The external sounder should sound for 1
second and then turn off. If the sounder does not
sound, CALL FOR SERVICE.
4. Fault zones. Open each protected door and window in turn and listen for three
beeps from the touchpad. Identification (zone number or zone description) of each
faulted protection point should appear on the display. The display clears when the
door or window is closed.
5. Walk in front of any interior motion detectors (if used) and listen for three beeps.
The identification of the detector should appear on the display when it is activated.
The display clears when no motion is detected.
Note that if wireless motion detectors are used, there is a 3-minute delay between
activations. This is to conserve battery life.
– 39 –
Download from Www.Somanuals.com. All Manuals Search And Download.
7HVWLQJꢀWKHꢀ6\VWHPꢀꢁ7Rꢀ%Hꢀ&RQGXFWHGꢀ:HHNO\ꢂ
6. Test all smoke detectors, following the manufacturer's instructions. The
identification of each detector should appear on the display when each is activated.
If a problem is experienced with any protection point (no confirming sounds, no
display), call for service immediately.
When all protection points have been checked and are intact (closed), there should
be no zone identification numbers displayed on the touchpad.
7. Exit test mode:
+ [ 1 ]
(Security Code)
If the test mode is inadvertently left active, it automatically turns off after 4 hours.
During the final 5 minutes (after 3 hours 55 minutes of Test mode), the keypad emits a
double-beep every 30 seconds to alert that the end of Test mode is nearing.
– 40 –
Download from Www.Somanuals.com. All Manuals Search And Download.
7URXEOHꢀ&RQGLWLRQV
"Check" and
"Battery" Displays
The word CHECK on the touchpad's display, accompanied by a
"beeping" at the touchpad, indicates a trouble condition in the
system.
To silen ce th e b eep in g for th ese con d ition s, p r ess a n y k ey.
1. A d isp la y of "CH ECK" a n d on e or m or e zon e n u m b er s
indicates that a problem exists with the displayed zone(s) and
requires your attention. Determine if the zone(s) displayed are
intact and make them so if they are not. If the problem has been
corrected, the display can be cleared if you enter the OFF
sequence (security code plus OFF key) twice. If the display
persists, CALL FOR SERVICE.
Note: A display of CHE CK 70 on English Display touchpads
indicates that the wiring connection to the external sounder is
at fault (opened or shorted), and you should CALL FOR
SERVICE. See “BELL FAILURE” on next page. A display of
CHE CK 90 indicates that RF interference may be impeding the
operation of wireless sensors* in the system. See “R cvr J a m ”
on next page.
2. If th er e a r e w ir eless sen sor s* in you r system , the CHECK
condition may also be caused by some change in the
environment that prevents the wireless receiver from receiving
messages from a particular sensor. CALL FOR SERVICE if this
occurs.
* Not all systems
use wireless
sensors.
IF YOU CANNOT COR R ECT A "CHECK" DISP LAY,
CALL F OR SER VICE.
TYP ICAL "CHECK" DISP LAYS
AC
06
' , ) ' / ꢆ ꢁ ꢀ
& ) ( 6 3 3 1 ꢆ ; - 2 ( 3 ;
CHECK
CUSTOM ENGLISH DISP LAY
TOUCHP AD
E NGLISH DISP LAY
TOUCHP AD
– 41 –
Download from Www.Somanuals.com. All Manuals Search And Download.
7URXEOHꢀ&RQGLWLRQVꢀꢁ&RQWLQXHGꢂ
Words or letters in parentheses ( ) are those that are
displayed on English Display touchpads.
COMM. F AILUR E
(or F C)
Indicates that a failure has occurred in
the telephone communication portion of
your system.
Other Trouble
Displays
CALL FOR SERVICE.
* Any “beeping” that
accompanies a trouble
display can be stopped
by depressing any key
on the touchpad or by
entering an OFF
SYSTE M LO BAT
(or BAT with no
zone No.)
Indicates that a low system battery
condition exists. Display is
accompanied by "beeping"* at the
touchpad. If this condition persists for
more than one day (with AC present),
CALL FOR SERVICE.
sequence (code + OFF)
LO BAT
Indicates that there is a low battery
condition in the wireless transmitter**
number displayed (00 is RF keypad).
+ zone descriptor
(or BAT with
zone No.)
** Not all systems use
wireless sensors.
*
Accompanied by a single "beep" (about
once every 40 seconds) at the touchpad.
Either replace the battery yourself, or
CALL FOR SERVICE. If the battery is
not replaced within 30 days, a CHECK
display may occur.
R cvr J a m
(or CHE CK 90)
Wireless part of the system is experiencing
RF interference which may impede
reception from wireless sensors.**
MODE M COMM
(or CC)
Indicates that the control is on-line with
the Customer Care Center's remote
computer.
The control will not operate while on-line.
Wait a few minutes — the display should
disappear.
BELL F AILUR E
(or CHE CK 70)
Indicates that the wiring connection to
the external sounder is at fault (open or
shorted). Accompanied by “beeping” at
the touchpad. CALL FOR SERVICE.
– 42 –
Download from Www.Somanuals.com. All Manuals Search And Download.
7URXEOHꢀ&RQGLWLRQVꢀꢁ&RQWLQXHGꢂ
Other Trouble
Displays
(Continued)
AC LOSS
(or NO AC)
The system is operating on battery power
only due to an AC power failure.
If only some lights are out on the
premises, check circuit breakers and
fuses and reset or replace as necessary.
If AC power cannot be restored and a
“low system battery” message appears
(see previous page), CALL F OR
SER VICE.
Bu sy-Sta n d by
(or d I)
If this message remains displayed for more
than 1 minute, system is disabled. CALL
F OR SER VICE .
OP EN CIRCUIT
(or OC)
The touchpad is not receiving signals from
the control. CALL FOR SERVICE.
Lon g R n g Tr b l
(or b F )
If part of your system, back-up Long
Range Radio communication has failed.
CALL FOR SERVICE.
TELCO F AULT
(or CHE CK 94)
The telephone line has a problem.
CALL FOR SERVICE.
If th er e is n o tou ch p a d d isp la y a t a ll, a n d th e R E ADY in d ica tor
is n ot lit, operating power (from AC and back-up battery) for the
system has stopped and the system is inoperative. CALL F OR
SER VICE.
Total Power Failure
In The Event Of Telephone Operational Problems
In the event of telephone operational problems, disconnect the control from the phone line by
removing the plug from the phone wall jack. We recommend that your installer demonstrate this
disconnection on installation of the system. Do not attempt to disconnect the phone connection
inside the control. Doing so will result in the loss of your phone lines. If the regular phones work
correctly after the control has been disconnected from the phone wall jack, the control has a
problem and you should immediately call for service. If upon disconnection of the control, there is
still a problem on the phone line, notify the Telephone Company that they have a problem and
request prompt phone repair service. The user may not under any circumstances attempt any
service or repairs to the security system. Repairs must be made only by ADT authorized service
(see the LIMITED WARRANTY statement for information on how to obtain service).
– 43 –
Download from Www.Somanuals.com. All Manuals Search And Download.
0DLQWDLQLQJꢀ<RXUꢀ6\VWHP
The components of your security system are designed to be as
Taking Care of
Your System
maintenance-free as possible. However, to make sure that your system
is in reliable working condition, do the following:
1. Test your system weekly.
2. Test your system after any alarm occurs.
Silencing Low
You can silence the touchpad’s warning tones by pressing the OFF key,
Battery Warning but the touchpad's low battery message display will remain on as a
reminder that you have a low battery condition in one or more of your
wireless sensors. When you replace the weak battery with a fresh one,
the sensor sends a "good battery" signal to the control as soon as the
sensor is activated (opening/closing of door, window, etc.), causing the
low battery display to turn off. If the sensor is not activated, the display
will automatically clear within approximately 1 hour.
Tones at the
Touchpad
Each wireless sensor in your system has a 9-volt or 3-volt battery. The
system detects a low battery in wireless sensors, including smoke
detectors, the personal emergency transmitter, and the portable
wireless touchpad and displays a low battery message*. (A low battery
in a portable wireless touchpad is detected as soon as one of its keys is
pressed, and displayed as 00.). Battery-operated smoke detectors with
a low battery also emit a single "chirp" sound approximately once
every 20–30 seconds.
Replacing
Batteries in
Wireless Sensors
Wireless sensors
may not have
been used in your
security system
Alkaline batteries provide a minimum of 1 year of operation, and in
most units and applications, provide 2–4 years of service. 3-volt lithium
batteries provide up to 4 or more years of operation. Actual battery life
will depend on the environment in which the sensor is used, the
number of signals that the transmitter in the sensor has had to send,
and the specific type of sensor. Factors such as humidity, high or low
temperatures or large swings in temperature, may all lead to the
reduction of actual battery life in an installation.
IMPORTANT:
Use only batteries
recommended by
your installer as
replacement.
* The low battery message comes on as a warning that battery replacement
in indicated sensor(s) is due within 30 days. In the meantime, a sensor
causing a low battery indication is still fully operational.
• Treat the components of your security system as you would any other
electrical equipment. Do not slam sensor-protected doors or windows.
• Keep dust from accumulating on the touchpad and all protective
sensors, particularly on motion sensors and smoke detectors.
• The touchpad and sensors should be cleaned carefully with a dry soft
cloth. Do n ot sp r a y w a ter or a n y oth er flu id on th e u n its.
Routine Care
– 44 –
Download from Www.Somanuals.com. All Manuals Search And Download.
)LUHꢀ$ODUPꢀ6\VWHPꢀꢁ,Iꢀ,QVWDOOHGꢂ
THIS SECTION AP P LIES ONLY TO RESIDENTIAL SYSTEMS
Your fire alarm system (if installed) is on 24 hours a day, for
continuous protection. In the event of an emergency, the strategically
located smoke and heat detectors will sound their alarms and
automatically send signals to your system, triggering a loud,
interrupted pulsed sound* from the Touchpad(s) and any external
sounders. A FIRE message will appear at your Touchpad and remain
on until you silence the alarm (see below for silencing fire alarms).
General
* Temporal pulse sounding is produced for Fire alarms, as follows:
3 pulses–pause–3 pulses–pause–3 pulses–pause. . . , repeated.
TYP ICAL F IRE EMERGENCY DISP LAYS
AC
* - 6 ) ꢆ ꢁ ꢅ ꢆ ꢆ ꢆ 1 % 7 8 ) 6
ꢀꢁ
ALARM
FIRE
& ) ( 6 3 3 1
CUSTOM DISP LAY TOUCHP AD
E NGLISH DISP LAY TOUCHP AD
1. You can silence the alarm at any time by pressing the OF F key (the
security code is not needed to silence fire alarms). To clear the
display, enter your code and press the OF F key again (to clear
Memory of Alarm).
Silencing
Fire Alarms and
Clearing Memory
of Alarm
2. If the Touchpad's FIRE display does not clear after the second OFF
sequence, smoke detectors may still be responding to smoke or heat
producing objects in their vicinity. Investigate, and should this be
the case, eliminate the source of heat or smoke.
3. If this does not remedy the problem, there may still be smoke in the
detector. Clear it by fanning the detector for about 30 seconds.
When the problem has been corrected, clear the display by
entering your code and pressing the OF F key.
Depending on the type of smoke detectors in your system, it may be
necessary to "reset" the smoke detectors after a fire alarm has been
turned off. Check with your installer. This "reset" is accomplished at a
touchpad, as follows:
Smoke Detector
Reset
Enter User Code*, then press the [1] key (* except “arm only” user).
NOTE: During smoke detector reset, “FAULT x” is displayed (about 6
seconds) and should disappear if the detector is clear.
– 45 –
Download from Www.Somanuals.com. All Manuals Search And Download.
)LUHꢀ$ODUPꢀ6\VWHPꢀꢁ&RQWLQXHGꢂ
THIS SECTION AP P LIES ONLY TO RESIDENTIAL SYSTEMS
1. Should you become aware of a fire emergency before your smoke or
heat detectors sense the problem, go to your nearest touchpad and
manually initiate an alarm by pressing the panic key assigned for
FIRE emergency for 2 seconds. If a key pair has been assigned for
fire, press both keys at the same time. See Using the Panic Keys
section below for further details.
Manually
Initiating
a Fire Alarm
2. Evacuate all occupants from the premises.
3. If flames and/or smoke are present, leave the premises and notify
your local Fire Department immediately.
4. If no flames or smoke are apparent, investigate the cause of the
alarm. The zone number(s) of the zone(s) in an alarm condition will
be displayed at the touchpad.
A key or key pair may have been assigned for manually initiating a
FIRE alarm. See the Panic Keys section for key assignments.
For convenience, indicate the key or key pair assigned for fire below.
I n d i v i d u a l K e y s
Using the Panic
Key(s) Assigned
for FIRE
Emergency
A
B
C
Press the individual key assigned for fire for 2
seconds.
O R
K e y P a i r s
1
O F F
and ∗ R E A D Y
∗
3
R E A D Y and
#
#
Press the key pair assigned
for fire at the same time.
S T A Y
and
DISP LAYS F OLLOWING MANUAL INITIATION OF A F IRE ALARM
AC
* - 6 ) ꢆ ꢇ ꢈ
ꢂꢃ
ALARM
FIRE
CUSTOM DISP LAY TOUCHP AD
E NGLISH DISP LAY TOUCHP AD
– 46 –
Download from Www.Somanuals.com. All Manuals Search And Download.
)LUHꢀ$ODUPꢀ6\VWHPꢀꢁ&RQWLQXHGꢂ
THIS SECTION AP P LIES ONLY TO RESIDENTIAL SYSTEMS
1DWLRQDOꢀ)LUHꢀ3URWHFWLRQꢀ$VVRFLDWLRQ
5HFRPPHQGDWLRQVꢀRQꢀ6PRNHꢀ'HWHFWRUV
With regard to the number and placement of smoke/heat detectors, we
subscribe to the recommendations contained in the National Fire Protection
Association's National Fire Alarm Code (NFPA 72) noted below.
Early warning fire detection is best achieved by the installation of fire
detection equipment in all rooms and areas of the household as follows: A
smoke detector installed outside of each separate sleeping area, in the
immediate vicinity of the bedrooms and on each additional story of the
family living unit, including basements and excluding crawl spaces and
unfinished attics.
In addition, the NFPA recommends that you install heat or smoke detectors
in the living room, dining room, bedroom(s), kitchen, hallway(s), attic,
furnace room, utility and storage rooms, basements and attached garages.
✪
▲
✪
✪
✪
✪
KITCHEN
▲
✪
KITCHEN
BDRM
DINING
BEDROOM
BEDROOM
TV ROOM
DINING
■
BDRM
LIVING ROOM
■
✪
✪
✪
■
✪
BEDROOM
BEDROOM
LIVING ROOM
✪
▲
Smoke Detectors for Minimum Protection
Smoke Detectors for Additional Protection
Heat-Activated Detectors
■
✪
▲
■
BEDROOM
■
✪
BEDROOM
✪
BEDROOM
TO
BR
▲
■
▲
KTCHN
GARAGE
CLOSED
DOOR
LVNG RM
.
■
BASEMENT
– 47 –
Download from Www.Somanuals.com. All Manuals Search And Download.
)LUHꢀ$ODUPꢀ6\VWHPꢀꢁ&RQWLQXHGꢂ
THIS SECTION AP P LIES ONLY TO RESIDENTIAL SYSTEMS
(PHUJHQF\ꢀ(YDFXDWLRQ
Establish and regularly practice a plan of escape in the
event of fire. The following steps are recommended by
the National Fire Protection Association:
OOM
CLOSET
BEDR
1. Position your detector or your interior and/or
exterior sounders so that they can be heard by all
H
OOM
OOM
BEDR
T
occupants.
BA
BEDR
2. Determine two means of escape from each room.
One path of escape should lead to the door that
permits normal exit from the building. The other
may be a window, should your path be impassable.
Station an escape ladder at such windows if there
is a long drop to the ground.
2ND FLOOR
OOM
KITCHEN
BEDR
BACK DOOR
H
OOM
T
3. Sketch a floor plan of the building. Show windows,
doors, stairs and rooftops that can be used to
escape. Indicate escape routes for each room. Keep
these routes free from obstruction and post copies
of the escape routes in every room.
BA
BEDR
1ST FLOOR
•
4. Assure that all bedroom doors are shut while you
are asleep. This will prevent deadly smoke from
entering while you escape.
•
5. Try the door. If the door is hot, check your
alternate escape route. If the door is cool, open it
cautiously. Be prepared to slam the door if smoke
or heat rushes in.
BACK
6. When smoke is present, crawl on the ground. Do
not walk upright, since smoke rises and may
overcome you. Clearer air is near the floor.
•
7. Escape quickly; don't panic.
FRONT
8. Establish a common meeting place outdoors, away
from your house, where everyone can meet and
then take steps to contact the authorities and
account for those missing. Choose someone to
assure that nobody returns to the house — many
die going back
– 48 –
Download from Www.Somanuals.com. All Manuals Search And Download.
4XLFNꢀ*XLGHꢀWRꢀ%DVLFꢀ6\VWHPꢀ)XQFWLRQV
P ROCEDURE
F UNCTION
COMMENTS
Ch eck Zon es
Press READY key.
View faulted zones when system not
ready.
Ar m System
Enter code. Press arming key desired:
Arms system in mode selected.
(AWAY, STAY, NIGHT-STAY,
INSTANT)
Qu ick Ar m
(if programmed)
Press #. Press arming key desired:
(AWAY, STAY, INSTANT)
Arms system in mode selected, quickly
and without use of a code.
Byp a ss Zon e(s)
Enter code. Press BYPASS key.
Enter zone number(s) to be bypassed
(use 2-digit entries).
Bypassed zones are unprotected and
will not cause an alarm if violated.
Qu ick Byp a ss
(if programmed)
Enter code. Press BYPASS key + [#].
Bypasses all faulted zones
automatically.
Silen ce Sou n d er s
Bu r gla r y:
Enter code. Press OFF key.
Also disarms system. Memory of alarm
remains until cleared.
F ir e:
Press OFF key.
Press any key.
Memory of Alarm remains until cleared.
Determine cause.
"Ch eck ":
Disa r m System
Enter code. Press OFF key.
Also silences sounders. Memory of
alarm remains until cleared.
Clea r Ala r m
Mem or y
After disarming, enter code again.
Press OFF key again.
Touchpad beeps rapidly on entry if
alarm has occurred while absent. Alarm
display will remain upon disarming
until cleared.
Du r ess (if active
and connected to
Customer Care Center)
Arm or disarm "normally", but
use your 4-digit Duress code to do so.
Performs desired action and sends
silent alarm to Customer Care Center.
P a n ic Ala r m s
(as programmed)
Press key [A], [B], or [C] for at least 2
seconds.
See the Panic Keys section for
emergency functions programmed for
your system. Note: Keys “A”, “B”, and
“C” may have been programmed for
other functions.
Ch im e Mod e
Test Mod e
To turn ON or OFF: Enter code. Press
CHIME key.
The touchpad will sound if doors or
windows are violated while system is
disarmed and chime mode is ON.
To turn ON: Enter code. Press TEST key. Tests alarm sounder and allows sensors
to be tested.
To turn OFF: Enter code. Press OFF key.
P h on e Access
(Smartphone Module)
if applicable
Consult Phone Access User's Guide that
accompanies the Phone Module.
Permits system access remotely, via
Touch-tone phone.
– 49 –
Download from Www.Somanuals.com. All Manuals Search And Download.
6XPPDU\ꢀRIꢀ$XGLEOHꢃ9LVXDOꢀ1RWLILFDWLRQV
(QJOLVKꢀ'LVSOD\ꢀ7RXFKSDGV
SOUND
CAUSE
DISP LAY
LOUD,
INTERRUPTED
FIRE ALARM
F IRE is displayed; zone number of zone in
alarm is displayed. If a fire alarm is manually
activated, zone number 95 will be displayed.
*
Touchpad & Ext.
LOUD,
BURGLARY/AUDIBLE
EMERGENCY ALARM
ALARM is displayed. Zone number of zone in
alarm is also displayed.
*
CONTINUOUS
Touchpad & Ext.
ONE SHORT BEEP a. SYSTEM DISARM
a. READY indicator light comes on.
(not repeated)
Touchpad only
b. SYSTEM ARMING ATTEMPT
WITH AN OPEN ZONE.
b. Number of the open protection zone displayed.
c. Zone numbers of the bypassed protection
zones are displayed (one beep is heard for
each zone displayed). Subsequently, BYP ASS
is displayed.
c. BYPASS VERIFY
ONE SHORT BEEP a. SYSTEM IS IN TEST MODE
a. Opened zone numbers will appear.
(once every 40 secs)
Touchpad only
b. LOW BATTERY AT A
TRANSMITTER
b. BAT displayed with zone number of
transmitter.
TWO SHORT BEEPS ARM AWAY
Touchpad only
AWAY is displayed. Red ARMED indicator is lit.
THREE SHORT
BEEPS
a. ARM STAY, NIGHT-STAY, OR a. STAY or INSTANT is displayed. Red
INSTANT
ARMED indicator is lit.
Touchpad only
b. CHIME displayed; zone number of open
protection zone will be displayed if the [✱]
key is pressed.
b. ZONE OPENED WITH
SYSTEM IN CHIME MODE.
RAPID BEEPING
Touchpad only
a. TROUBLE
a. CHECK displayed. Zone number of troubled
protection zone is displayed.
b. MEMORY OF ALARM
b. F IRE or ALARM is displayed; zone number
of zone in alarm is displayed
c. BAT displayed with no zone ID number.
c. SYSTEM LOW BATTERY
d. EXT. SOUNDER WIRING FAIL d. CHECK 70 is displayed.
SLOW BEEPING
Touchpad only
a. AWAY is displayed.
a. EXIT DELAY WARNING
b. ENTRY DELAY WARNING
b. Exceeding the entry delay time without
disarming causes alarm.
*
If a bell is used as external sounder, fire alarm is pulsed ring; burglary/audible emergency is steady ring.
– 50 –
Download from Www.Somanuals.com. All Manuals Search And Download.
6XPPDU\ꢀRIꢀ$XGLEOHꢁ9LVXDOꢀ1RWLILFDWLRQV
&XVWRPꢀ(QJOLVKꢀ'LVSOD\ꢀ7RXFKSDGV
SOUND
CAUSE
DISP LAY
LOUD,
INTERRUPTED*
Touchpad & Ext.
FIRE ALARM.
F IRE is displayed; descriptor of zone in alarm is
displayed. If a fire alarm is manually activated, zone
number 95 will be displayed.
LOUD,
CONTINUOUS*
Touchpad & Ext.
BURGLARY/AUDIBLE
EMERGENCY ALARM.
ALARM is displayed. If programmed, descriptor of
zone in alarm is also displayed
ONE SHORT BEEP a. SYSTEM DISARM.
(not repeated)
a. DISARMED/READY TO ARM is displayed.
b. Number and descriptor of open protection zone is
displayed.
b. SYSTEM ARMING ATTEMPT
Touchpad only
WITH AN OPEN ZONE.
c. Numbers and descriptors of the bypassed zones
are displayed (One beep is heard for each
c. BYPASS VERIFY.
zone displayed). Subsequently, the following is
displayed: DISARMED BYP ASS /Rea d y to Ar m .
ONE SHORT BEEP a. SYSTEM IS IN TEST MODE. a. Opened Zone identifications will appear.
(once every 40 secs)
Touchpad only
b, LOW BATTERY AT A
TRANSMITTER.
b. LO BAT displayed with description of transmitter.
TWO SHORT BEEPS ARM AWAY.
Touchpad only
ARMED AWAY displayed. Red ARMED indicator
lit.
THREE SHORT
BEEPS
a. ARM STAY, NIGHT-STAY,
OR INSTANT.
a. ARMED STAY or ARMED INSTANT displayed.
Red ARMED indicator lit.
Touchpad only
b. CHIME displayed, descriptor of open protection
zone will be displayed if the [✱] key is pressed.
b. ZONE OPENED WHILE
SYSTEM IS DISARMED.
RAPID BEEPING
Touchpad only
a. TROUBLE.
a. CHECK displayed. Descriptor of troubled
protection zone is displayed.
b. MEMORY OF ALARM.
b. F IRE or ALARM is displayed; descriptor of zone
in alarm is displayed.
c. SYSTEM LO BAT displayed.
c. SYSTEM LOW BATTERY.
d. EXT. SOUNDER WIRE FAIL.
d. BELL F AILURE is displayed.
SLOW BEEPING
Touchpad only
a. EXIT DELAY WARNING
(if programmed).
a. ARMED AWAY is displayed along with You Ma y
Exit Now .
b. DISARM SYSTEM OR ALARM WILL OCCUR
is displayed. Exceed in g th e d ela y tim e w ith ou t
d isa r m in g ca u ses a n a la r m .
b. ENTRY DELAY WARNING.
* If a bell is used as external sounder, fire alarm is pulsed ring; burglary/audible emergency is steady
ring.
– 51 –
Download from Www.Somanuals.com. All Manuals Search And Download.
5HJXODWRU\ꢀ6WDWHPHQWVꢀDQGꢀ:DUQLQJV
NOTE : Th is is a “Gr a d e A” R esid en tia l System
R ADIO F R EQUENCY EMISSIONS
F ed er a l Com m u n ica tion s Com m ission (F CC) P a r t 15
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
In d u str y Ca n a d a
This Class B digital apparatus complies with Canadian ICES-003.
Cet Appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
TELEP HONE/MODEM INTER F ACE
F CC P a r t 68
This equipment complies with Part 68 of the FCC rules. On the front cover of this equipment is a
label that contains the FCC registration number and Ringer Equivalence Number (REN). You must
provide this information to the telephone company when requested.
This equipment uses the following USOC jack: RJ 31X
This equipment may not be used on telephone-company-provided coin service. Connection to party
lines is subject to state tariffs. This equipment is hearing-aid compatible.
In d u str y Ca n a d a
NOTICE : The Industry Canada Label identifies certified equipment. This certification means that
the equipment meets telecommunications network protective, operational and safety requirements
as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The
Department does not guarantee the equipment will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the
facilities of the local telecommunications company. The equipment must also be installed using an
acceptable method of connection. The customer should be aware that compliance with the above
conditions may not prevent degradation of service in some situations.
Repairs to certified equipment should be coordinated by a representative designated by the supplier.
Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give
the telecommunications company to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the power
utility, telephone lines and internal metallic water pipe system, if present, are connected together,
This precaution may be particularly important in rural areas.
Ca u tion : Users should not attempt to make such connections themselves but should contact
appropriate electric inspection authority, or electrician, as appropriate.
R in ger E q u iva len ce Nu m b er Notice:
The R in ger E qu iva len ce Nu m ber (REN) assigned to each terminal device provides an indication
of the maximum number of terminals allowed to be connected to a telephone interface. The
termination on an interface may consist of any combination of devices subject only to the
requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.
– 52 –
Download from Www.Somanuals.com. All Manuals Search And Download.
5HJXODWRU\ꢀ6WDWHPHQWVꢀꢁ&RQWLQXHGꢂ
In d u str ie Ca n a d a
AVIS: l’étiquette d’Industrie Canada identifie le matériel homologué. Cette étiquette certifie que le
matériel est conforme aux normes de protection, d’exploitation et de sécurité des réseaux de
télécommunications, comme le prescrivent les documents concernant les exigences techniques
relatives au matériel terminal. Le Ministère n’assure toutefois pas que le matériel fonctionnera à la
satisfaction de l’utilisateur.
Avant d’installer ce matériel, l’utilisateur doit s’assurer qu’il est permis de le raccorder aux
installations de l’enterprise locale de télécommunication. Le matériel doit également être installé en
suivant une méthode acceptée da raccordement. L’abonné ne doit pas oublier qu’il est possible que la
conformité aux conditions énoncées ci-dessus n’empêche pas la dégradation du service dans
certaines situations.
Les réparations de matériel nomologué doivent être coordonnées par un représentant désigné par le
fournisseur. L’entreprise de télécommunications peut demander à l’utilisateur da débrancher un
appareil à la suite de réparations ou de modifications effectuées par l’utilisateur ou à cause de
mauvais fonctionnement.
Pour sa propre protection, l’utilisateur doit s’assurer que tous les fils de mise à la terre de la source
d’energie électrique, de lignes téléphoniques et des canalisations d’eau métalliques, s’il y en a, sont
raccordés ensemble. Cette précaution est particulièrement importante dans les régions rurales.
Aver tissem en t : L’utilisateur ne doit pas tenter de faire ces raccordements lui-même; il doit avoir
racours à un service d’inspection des installations électriques, ou à un électricien, selon le cas.
AVIS : L’in d ice d ’équ iva len ce d e la son n er ie (IES) assigné à chaque dispositif terminal indique
le nombre maximal de terminaux qui peuvent être raccordés à une interface. La terminaison d’une
interface téléphonique peut consister en une combinaison de quelques dispositifs, à la seule
condition que la somme d’indices d’équivalence de la sonnerie de tous les dispositifs n’excède pas 5.
– 53 –
Download from Www.Somanuals.com. All Manuals Search And Download.
&KDUWVꢀRIꢀ<RXUꢀ6\VWHP·Vꢀ)HDWXUHV
Features
Comments
Part. 2:
Exit Delay
Part. 1:
Part. 1:
Part. 1:
Zones:
yes
Entry Delay 1
Part. 2:
Part. 2:
Entry Delay 2
Night-Stay Zones
Quick Arm
no
no
no
Quick Bypass
yes
Automatic Paging
Keyswitch Arming
(circle type of LED lighting)
yes
users:
flash
flash
Arm AWAY: steady
Arm STAY: steady
inactivity alert time:
daily monitoring times:
Up and About Schedule
F u n ct ion Keys
The following chart identifies the special functions that yourinstaller may have programmed
for certain keys.
F u n ction Keys
A
B
C
D
Com m en ts
• Single-Button Arming
• Step Arming
• Paging (see Paging chart below)
• Time/Date Display
• Macro Key 1
• Macro Key 2
• Macro Key 3
• Macro Key 4
††
• Emergency Key : Personal
††
• Emergency Key : Silent Alarm
††
• Emergency Key : Audible Alarm
††
• Emergency Key : Fire
Device:
• Device Activation
†† Emergency Keys:
A = [1] / [∗]
B = [∗] / [#]
C = [3] / [#]
– 54 –
Download from Www.Somanuals.com. All Manuals Search And Download.
&KDUWVꢀRIꢀ<RXUꢀ6\VWHP·Vꢀ)HDWXUHV
User Set u p
The following chart will help keep track of system users. Copies should be
distributed to the partition 1 and partition 2 masters for their records.
To program a user attribute:
Enter system/partition master code + [8] + user no. + “#” command listed in column heading…
User
No.
User
Name
User’s Part(s).
Security
Code
enter new code
Auth.
Level
Access
Group
RF Zone
Number
Pager
on/off
(system master only)
[#] [3] + part(s) + [#]
[#] [1] + level [#] [2] + group [#] [4] + zone no. [#] [5] + 0/1
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
installer
master
part. 1 master
(all)
(all)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
installer
master
(0)
(0)
(0)
(0)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(4)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
– 55 –
Download from Www.Somanuals.com. All Manuals Search And Download.
&KDUWVꢀRIꢀ<RXUꢀ6\VWHP·Vꢀ)HDWXUHV
User Set u p (con t in u ed )
(Enter system/partition master code + [8] + user no. + “#” command listed in column heading…)
User
No.
User
Name
User’s Part(s).
Security
Code
enter new code
Auth.
Level
Access
Group
RF Zone
Number
Pager
on/off
(system master only)
[#] [3] + part(s) + [#]
[#] [1] + level [#] [2] + group [#] [4] + zone no. [#] [5] + 0/1
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
part. 2 master
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(4)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
Authority Levels: 0 = standard user
1 = arm only
Partitions: 1 = partition 1 and common
2 = partition 2 and common
2 = guest
3 = common partition only
3 = duress
4 = partition master
Paging: 0 = no paging
1 = allow paging
P a gin g Setu p
Automatically Reports Upon…
open/close alarm/trouble zone list
p1 p2 p1 p2 p1 p2
Sched. Func. Key
Pager Phone Number\
Pager Prefix Characters
1
2
3
4
– 56 –
Download from Www.Somanuals.com. All Manuals Search And Download.
&KDUWVꢀRIꢀ<RXUꢀ6\VWHP·Vꢀ)HDWXUHV
Sch ed u les (master code + [#] + [6] [4])
No.
Event
Device No. Group No. Partition
Start
Stop
Time/
Day
Repeat Random
(see list below)
for “01” events:
for “02” events: for “04-06” events: Time/
enter 1-8 enter 1, 2, or 3
(yes/no)
(yes/no)
enter 01-18
Day
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
Events: 00 = clear event
01 = device on/off
03 = latch key report
04 = forced STAY arm
05 = forced AWAY arm
06 = auto disarm
07 = display “reminder”
02 = user access
List of Ou tp u t Devices
Device
01
Descr ip t ion
Sch ed u le No.
F u n ct ion Key
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
– 57 –
Download from Www.Somanuals.com. All Manuals Search And Download.
²ꢀ1RWHVꢀ²
– 58 –
Download from Www.Somanuals.com. All Manuals Search And Download.
²ꢀ1RWHVꢀ²
– 59 –
Download from Www.Somanuals.com. All Manuals Search And Download.
²ꢀ1RWHVꢀ²
– 60 –
Download from Www.Somanuals.com. All Manuals Search And Download.
²ꢀ1RWHVꢀ²
– 61 –
Download from Www.Somanuals.com. All Manuals Search And Download.
/,0,7$7,216ꢀ2)ꢀ7+,6ꢀ6<67(0
WARNING! THE LIMITATIONS OF THIS ALARM SYSTEM
While this system is an advanced design security system, it does not offer guaranteed protection against burglary or other
emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for
variety of reasons. For example:
a
•
Intruders may gain access through unprotected openings or have the technical sophistication to bypass an alarm
sensor or disconnect an alarm warning device.
•
Intrusion detectors (e.g. passive infrared detectors), smoke detectors, and many other sensing devices will not work
without power. Battery operated devices will not work without batteries, with dead batteries, or if the batteries are
not put in properly. Devices powered solely by AC will not work if their AC power supply is cut off for any reason,
however briefly.
•
Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver. Even
if the signal path has been recently checked during a weekly test, blockage can occur if a metal object is moved into
the path.
•
•
A user may not be able to reach a panic or emergency button quickly enough.
While smoke detectors have played a key role in reducing residential fire deaths in the United States, they may not
activate or provide early warning for a variety of reasons in as many as 35% of all fires, according to data published
by the Federal Emergency Management Agency. Some of the reasons smoke detectors used in conjunction with this
System may not work are as follows. Smoke detectors may have been improperly installed and positioned. Smoke
detectors may not sense fires that start where smoke cannot reach the detectors, such as in chimneys, in walls, or
roofs, or on the other side of closed doors. Smoke detectors also may not sense a fire on another level of a residence or
building. A second floor detector, for example, may not sense a first floor or basement fire. Moreover, smoke detectors
have sensing limitations. No smoke detector can sense every kind of fire every time. In general, detectors may not
always warn about fires caused by carelessness and safety hazards like smoking in bed, violent explosions, escaping
gas, improper storage of flammable materials, overloaded electrical circuits, children playing with matches, or arson.
Depending upon the nature of the fire and/or the locations of the smoke detectors, the detector, even if it operates as
anticipated, may not provide sufficient warning to allow all occupants to escape in time to prevent injury or death.
Passive Infrared Motion Detectors can only detect intrusion within the designed ranges as diagrammed in their
installation manual. Passive Infrared Detectors do not provide volumetric area protection. They do create multiple
beams of protection, and intrusion can only be detected in unobstructed areas covered by those beams. They cannot
detect motion or intrusion that takes place behind walls, ceilings, floors, closed doors, glass partitions, glass doors, or
windows.
•
Mechanical tampering, masking, painting or spraying of any material on the mirrors, windows or any part of the
optical system can reduce their detection ability. Passive Infrared Detectors sense changes in temperature; however,
as the ambient temperature of protected area approaches the temperature range of 90° to 105°F, the detection
performance can decrease.
•
Alarm warning devices such as sirens, bells or horns may not alert people or wake up sleepers if they are located on
the other side of closed or partly open doors. If warning devices sound on a different level of the residence from the
bedrooms, then they are less likely to waken or alert people inside the bedrooms. Even persons who are awake may
not hear the warning if the alarm is muffled from a stereo, radio, air conditioner or other appliance, or by passing
traffic. Finally, alarm warning devices, however loud, may not warn hearing-impaired people or waken deep sleepers.
Telephone lines needed to transmit alarm signals from a premises to a central monitoring station may be out of
service or temporarily out of service. Telephone lines are also subject to compromise by sophisticated intruders.
Even if the system responds to the emergency as intended, however, occupants may have insufficient time to protect
themselves from the emergency situation. In the case of a monitored alarm system, authorities may not respond
appropriately.
•
•
•
This equipment, like other electrical devices, is subject to component failure. Even though this equipment is designed
to last as long as 10 years, the electronic components could fail at any time.
The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance.
This alarm system should be tested weekly to make sure all sensors and transmitters are working properly.
Installing an alarm system may make one eligible for lower insurance rates, but an alarm system is not a substitute for
insurance. Homeowners, property owners and renters should continue to act prudently in protecting themselves and
continue to insure their lives and property.
We continue to develop new and improved protection devices. Users of alarm systems owe it to themselves and their loved
ones to learn about these developments.
– 62 –
Download from Www.Somanuals.com. All Manuals Search And Download.
/,0,7('ꢀ:$55$17<
Terms and Conditions Applying to Sale of Equipment
Any part of the system, including the wiring, installed under this Agreement which proves to be
defective in material or workmanship within 90 days of the date of completion of installation will
be repaired or replaced at ADT's option with a new functionally operative part. Labor and
material required to repair or replace such defective components or to make mechanical
adjustments to the system will be free of charge for a period of 90 days following the completion
of the original installation.
This warranty is extended only to the original consumer purchaser of the system and may be
enforced only by such person.
To obtain service under this warranty, call or write our local ADT Service Department at the
telephone number or address found in your local yellow pages.
Service pursuant to the warranty will be furnished only during ADT's normal working hours
8:00A.M. to 4:30P.M., Monday through Friday, except holidays. Services rendered outside the
normal working hours of ADT are not within the scope of this warranty and any services
requested to be performed at such times shall be charged for at ADT's then applicable rates for
labor and material.
This warranty does not apply to the conditions listed below, and in the event customer calls
ADT for service under the warranty and upon inspection it is found that one of these conditions
has led to the inoperability or apparent inoperability of the system, a charge will be made for the
service call of the ADT representative, whether or not he actually works on the system. Should
it actually be necessary to make repairs to the system due to one of the "conditions Not
Covered By Warranty", a charge will be made for such work at ADT's then applicable rates for
labor and material.
Conditions Not Covered By Warranty.
A. Damage from accidents, acts of God, alterations, misuse, tampering or abuse.
B. Failure of the customer to properly close or secure a door, window, or other point protected
by a burglar alarm device.
C. Failure of customer to properly follow operating instructions provided by ADT at time of
installation or at a later date.
D. Trouble in leased telephone.
E. Trouble due to interruption of commercial power.
F. Battery replacements.
– 63 –
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY (Continued)
This warranty is in lieu of all other express warranties. Any implied warranties of merchantability
and fitness for a particular purpose are limited in duration to a period of 90 days from the date
of completion of installation. The exclusive remedy of the customer hereunder shall be repair or
replacement as stated above. Under no circumstances shall ADT be liable to the customer or
any other person for incidental or consequential damages of any nature, including without
limitation, damages for personal injury or damages to property, and, however occasioned,
whether alleged as resulting from breach of warranty by ADT, the negligence of ADT, or
otherwise, ADT's liability will in no event exceed the purchase price of the system. Some states
may not allow limitations on how long an implied warranty lasts, or the exclusion or limitations of
incidental or consequential damages, so the above limitations and exclusions may not apply to
you, unless a longer period is required by applicable law. Any action against ADT in connection
with a system must be commenced within one year after the cause of action has occurred.
No agent, employee or representative of ADT nor any other person is authorized to modify this
warranty in any respect.
This warranty gives you specific legal rights and you may also have other rights which vary from
state to state.
ADT agrees to install the equipment in a workmanlike manner in accordance with the
following conditions:
A. Customer will make premises available without interruption during ADT normal working
hours 8:00A.M. to 4:30P.M., Monday through Friday, except Holidays.
B. Customer understands that the installation will necessitate drilling into various parts of the
premises: ADT intends, generally, to conceal wiring in the finished areas of the premises;
however, there may be areas which, due to construction, decoration, or furnishing of the
premises, ADT determines, in its sole discretion, that it would be impractical to conceal
wiring and, in such cases, wiring will be exposed.
C. Customer agrees to provide 110 VAC electrical outlets at designated locations for
equipment requiring AC power.
D. Customer to provide for lifting and replacing carpeting, if required, for installation of floor
mats or wiring.
–––––––––––––––––––––––––––––––– ALL RIGHTS RESERVED –––––––––––––––––––––––––––
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any
form, or by any means – electronic, mechanical, photocopying, recording, or otherwise without
the written permission of ADT Security Systems, Inc. The material in this publication is for
information purposes and subject to change without notice. ADT Security Systems, Inc.
assumes no responsibility for any errors which may appear in this publication.
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
ADT Security Services, Inc. One Town Center Rd. Boca Raton, FL 33486
Copyright © 2000
¬.ꢀꢁꢂꢃ9ꢁGl
K5309V3 6/02
Download from Www.Somanuals.com. All Manuals Search And Download.
|