®
ELECTRIC CHAIN SAW
OWNER’S MANUAL
®
MODELS
LNT-2: 076728K, 099178H, 100089-06, 100089-08, & 107709-01
EL-7: 075762J, 098031J, 099039J, 100089-04, 100089-05,
100089-07, & 107714-02
Pole Saw: 104316-04 (8"), 106890-01(10")
Pole Saw Assembly: 104317 (8"), 106821 (10")
IMPORTANT:Readandunderstandthismanualbeforeassemblingor
operating this chain saw. Improper use of saw can cause severe
injury. Keep this manual for future reference.
®
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER’S MANUAL
MAINTENANCE AND
STORAGE OF CHAIN SAW
1. Unplug chain saw from power source
• when not in use
SAFETY
WARNINGS
KICKBACK
• before moving from one place to an-
other
• before servicing
• before changing accessories or at-
tachments, such as saw chain and
guard
WARNING: Kickback may oc-
cur when the nose or tip of the
guide bar touches an object, or
when the wood closes in and
pinches the saw chain in the cut.
Tip contact in some cases may
cause a lightning fast reverse re-
action, kicking the guide bar up
and back towards the operator.
Pinching the saw chain along the
topoftheguidebarmaypushthe
guide bar rapidly back towards
the operator. Either of these re-
actions may cause you to lose
control of the saw which could
result in serious injury to user.
Direction
Do Not Let
Guide Bar
Touch Here
2. Inspect chain saw before and after each
use. Check saw closely if guard or other
part has been damaged. Check for any
damage that may affect operator safety
or operation of saw. Check for align-
ment or binding of moving parts. Check
for broken or damaged parts. Do not
use chain saw if damage affects safety
or operation. Have damage repaired by
authorized service center.
90°
Quadrant
3. Maintain chain saw with care.
• Never expose saw to rain.
• Keep chain sharp, clean, and lubri-
cated for better and safer performance.
• Follow steps outlined in this manual
to sharpen chain.
Figure 1 - Kickback Hazard Example: Do
Not Let Nose of Guide Bar Touch Object
While Chain is Moving
Kickback Safety Devices On
This Saw
This saw has a low-kickback chain and
reduced kickback guide bar. Both items
reduce the chance of kickback. Kickback
can still occur with this saw.
• Never try cutting through two logs at
same time. Only cut one log at a time.
• Keep handles dry, clean, and free of
oil and grease.
• Do not bury guide bar nose or try plunge
cut (boring into wood using guide bar
nose).
• Keep all screws and nuts tight.
• Inspect power cord often. If dam-
aged, have repaired by authorized
service center.
• Never carry chain saw by power cord.
• Never yank power cord to unplug it.
• Keep power cord from heat, oil, and
sharp edges.
Properly install front hand guard. This item
can reduce injuries from kickback. Follow
assembly instructions on page 6. Do not
remove front hand guard. Do not replace
front hand guard with substitute.
• Watch for shifting of wood or other
forces that may pinch chain.
• Use extreme caution when reentering a
previous cut.
The following steps will reduce the risk of
kickback.
• Use low-kickback chain and guide bar
supplied with this chain saw. Only re-
place these parts with chains and guide
bars listed in this manual.
• Inspect extension cords often and
replace if damaged.
• Use both hands to grip saw while saw is
running. Use firm grip. Thumbs and
fingers must wrap around saw handles.
4. When servicing, use only identical re-
placement parts.
• Never use dull or loose chain. Keep chain
sharp with proper tension.
• Keep all safety items in place on saw.
Make sure they work properly.
5. When not in use, always store chain saw
• in a high or locked place, out of
children’s reach
• Do not hand sharpen chain on automatic
chain sharpening (Fast Sharp) models.
• Do not overreach or cut above shoulder
height.
• in a dry place
• Keep solid footing and balance at all
times
• in a carrying case or with scabbard
over guide bar
Saw Maintenance and Kickback
Safety
• Stand slightly to left side of saw. This
keeps your body from being in direct line
with chain.
Keep this manual for reference. It is your
guide to safe and proper operation of this
chain saw.
Follow maintenance instructions in this
manual. Proper cleaning of saw and chain
and guide bar maintenance can reduce
chances of kickback. Inspect and maintain
saw after each use. This will increase the
service life of your saw. Note: Even with
proper sharpening, risk of kickback can
increase with each sharpening.
• Do not let guide bar nose touch anything
when chain is moving (see Figure 1).
107990
3
Download from Www.Somanuals.com. All Manuals Search And Download.
®
ELECTRIC CHAIN SAW
Low-Kickback Chain Chain that reduces
chance of kickback as required by ANS front of saw body beside guide bar. Keep
B175.1.
Spiked Bumper (Spike) Pointed teeth at
CHAIN SAW NAMES
AND TERMS
Bucking Process of cutting a felled tree or
log into lengths.
spiked bumper in contact with wood when
felling or bucking. It helps maintain posi-
tion of saw while cutting.
NormalCuttingPosition Stanceusedwhile
making bucking and felling cuts.
Sprocket Toothed wheel that drives chain.
Notching Cut Notch cut in tree that directs
fall of tree.
Felling Process of cutting down a tree.
Switch Device that completes or interrupts
electrical circuit to motor of saw.
Felling Cut Final cut when felling a tree.
Make this cut on opposite side of tree from
notching cut.
Oiler Control System for oiling guide bar
and chain.
SwitchLinkage Thisdeviceconnectsswitch
totrigger.Itmovesswitchwhenyousqueeze
trigger.
Power Head Chain saw without chain and
guide bar. Also known as saw body.
Front Handle Located at front of saw body.
Front Hand Guard Shield between front
handle and guide bar. Protects left hand
while using saw.
Switch Lockout Device that reduces acci-
dental starting of saw.
Pushback (Kickback, Pinch) Rapid
pushback of chain saw. Pushback may oc-
curifchainalongtopofguidebarispinched, Trigger Device that turns saw on and off.
caught, or contacts a foreign object. Squeezing trigger turns saw on.
Guide Bar Metal bar that extends from saw
body.Theguidebarsupportsandguideschain.
Rear Handle Handle located at rear of saw Releasing trigger turns saw off.
body.
Guide Bar Nose Tip or end of guide bar.
Trimming (Pruning) Process of cutting
Kickback Quick backward and upward
motion of guide bar. Kickback may occur
when tip of guide bar touches an object
while chain is moving. The guide bar will
kick up and back towards operator.
Reduced Kickback Guide Bar Guide bar limb(s) from a living tree.
that reduces chance of kickback.
Undercut Anupwardcutfromundersideof
Replacement Chain Chain that complies log or limb. This is done while in normal
with ANS B175.1 when used with a specific cutting position and cutting with top of
saw. It may not meet ANS requirements guide bar.
Limbing Process of cutting limb(s) from a
felled tree.
when used with other saws.
Saw Chain (Chain) Loop of chain having
cutting teeth for cutting wood. The motor
drives chain. The guide bar supports chain.
107990
4
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER’S MANUAL
PRODUCT
IDENTIFICATION
UNPACKING
1. Remove all items from carton.
Front Hand
Guard
Guide Bar
Nose
2. Check all items for any shipping dam-
age. If you find any damage or if any
parts are missing, promptly inform
dealer where you bought chain saw.
Saw
Chain
Rear
Handle
Guide Bar
Sprocket
Cover
Rear Hand
Guard
Scabbard
Power Cord
Oil Level Sight Hole
(located on saw body,
hidden by front handle)
Oil Cap With
Squeeze Bulb
Front Handle
Spike
Switch
Lockout
Trigger
Motor
Housing
Figure 2 - Electric Chain Saw
107990
5
Download from Www.Somanuals.com. All Manuals Search And Download.
®
ELECTRIC CHAIN SAW
8. Place chain around drive sprocket, then
ASSEMBLY
CAUTION: Do not place chain
on saw backwards. If chain is
backwards,sawwillvibratebadly
and will not cut.
along top groove of guide bar and
around guide bar nose. Note: Make
sure cutting edges of chain are facing
the right direction. Position chain so
cutting edges on top of guide bar face
guide bar nose (see Figure 3).
Note: Some models are pre assembled. As-
sembly is not needed on these models.
See Saw ChainTension Adjustment, page 7.
9. Adjust saw chain tension. Follow steps
under Saw Chain Tension Adjustment,
page 7.
WARNING: Cutting edges on
chain are sharp. Use protective
gloves when handling chain.
Tapping
Screw
Front Hand
Guard
Cutting
Edge
Towards
Guide
Bar Nose
IMPORTANT:Donotclampchain
saw in vise during assembly.
The plastic hardware bag should include:
• two guide bar bolts
Saw
Chain
Cutting
Edge
• two guide bar nuts
Guide Bar
Bolts
• one Phillips-head tapping screw
• automatic chain sharpener (Fast Sharp
models only)
Mounting
Stand-Outs
Drive
Sprocket
1. Lay chain out flat.
2. Install front hand guard onto saw body.
Do this by pressing two mounting stand-
outs on hand guard into hex-shaped
holes in saw body (see Figure 3).
3
Insert tapping screw through hand
guard and into saw handle. Tighten
screw firmly.
Guide
Bar
4. Turn adjusting screw counterclockwise
(see Figure 4). Continue to turn adjust-
ing screw until adjusting block is to rear
of adjusting plate.
Adjusting
Hole
Guide Bar
Nuts
5. Install guide bar onto saw body. Place
rear of guide bar between adjusting
plate and sprocket support.
IMPORTANT: Make sure to insert ad-
justing block into oval adjusting hole
on guide bar.
Figure 3 - Assembling Guide Bar, Chain, and Hand Guard
6. Line up holes on sprocket support with
center slot on guide bar and holes in
saw body.
Adjusting
Block
Adjusting
Plate
7. Insert guide bar bolts through front
hand guard, saw body, center slot of
guide bar, and sprocket support.Attach
guide bar nuts to guide bar bolts.
Adjusting
Screw
IMPORTANT: Tighten guide bar nuts
finger tight only. Make sure adjust-
ing block is in oval adjusting hole on
guide bar.
Sprocket
Support
Figure 4 - Part Locations For Assembling Guide Bar
107990
6
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER’S MANUAL
4. After chain tension is correct, tighten
SAW CHAIN
TENSION
FILLING OIL TANK
guide bar nuts firmly. If not, guide bar
will move and loosen chain tension.
This will increase the risk of kickback.
This can also damage saw. Note:A new
chain will stretch. Check new chain
after first few minutes of operation.
Allow chain to cool down. Readjust
chain tension.
1. Remove oil cap.
2. Fill oil tank with SAE #30 motor oil.
Note: For temperatures below 30°F, use
SAE #10 oil. For temperatures above
75°F, use SAE #40 oil.
3. Replace oil cap at once. Tighten oil cap
firmly for good seal. This will avoid oil
seepage from tank.
ADJUSTMENT
WARNING:Unplugchainsaw
frompowersourcebeforeadjust-
ing saw chain tension.
WARNING: Cutting edges on
chain are sharp. Use protective
gloves when handling chain.
4. Wipe off excess oil.
Note: It is normal for oil to seep when saw
is not in use. Empty oil tank after each use to
prevent seepage.
WARNING: Maintain proper
chain tension always. A loose
chain will increase the risk of
kickback.Aloosechainmayjump
outofguidebargroove.Thismay
injure operator and damage
chain. A loose chain will cause
chain, guide bar, and sprocket to
wear rapidly.
Note: For pre-assembled models, the saw
chain tension is properly set at factory. A
new chain will stretch. Check new chain
after first few minutes of operation. Allow
chain to cool down. Follow steps below to
readjust saw chain tension.
Figure 5 - Turning Adjusting Screw
Guide Bar Nuts
1. Before adjusting chain, make sure
guide bar nuts are only finger tight (see
Figure 3, page 6).Also make sure adjust-
ing block is in oval adjusting hole on
guide bar (see Figures 3 and 4, page 6).
Guide Bar
2. Turn adjusting screw clockwise until
all slack is out of chain (see Figure 5).
Note: There should be no gap between
side links of chain and bottom of guide
bar (see Figure 6).
Guide Bar
Correct
Tension
Gap
3. Wearing protective gloves, move chain
around guide bar. Chain should move
freely. If chain does not move freely,
loosen chain by turning adjusting screw
counterclockwise.
Incorrect
Tension
Figure 6 - Saw Chain Adjustment
107990
7
Download from Www.Somanuals.com. All Manuals Search And Download.
®
ELECTRIC CHAIN SAW
Keep cord away from cutting area. Make
CUTTING WITH THE CHAIN
SAW
1. Connect saw to extension cord. Con-
nect extension cord to power supply.
OPERATING CHAIN
SAW
sure cord does not catch on branches or logs
during cutting. Inspect cords often. Replace
damaged cords.
WARNING: Read and under-
stand this owner’s manual be-
fore operating this saw. Make
certain you read and understand
all Safety Warnings, pages 2 and
3. Improper use of this chain saw
can cause severe injury or death
fromfire,electricalshock,orbody
contact with moving chain, or
falling wood.
The extension cord may come undone from
the power cord during use. To avoid this,
make a knot with the two cords as shown in
Figure 7 below.
2. Make sure section of log to be cut is
not laying on ground. This will keep
chain from touching ground as it cuts
through log. Touching ground with
moving chain will dull chain.
Chain Saw
Power Cord
Extension
Cord
3. Use both hands to grip saw.Always use
left hand to grip front handle and right
hand to grip rear handle. Use firm grip.
Thumbs and fingers must wrap around
saw handles (see Figure 9).
EXTENSION CORDS
4. Make sure your footing is firm. Keep
feet apart. Divide your weight evenly
on both feet.
Use proper extension cords with this saw.
Use only extension cords marked for out-
door use. The cord must be marked with
suffix W or W-A following the cord type
designation. Example: SJTW-A or SJTW.
Figure 7 - Tying Extension Cord and
Power Cord in Knot
5. When ready to make a cut, press in
switch lockout with right thumb and
squeeze trigger (see Figure 9). This will
turn saw on. Releasing trigger will turn
saw off. Make sure saw is running at
full speed before starting a cut.
OILING CHAIN
Use proper sized cord with this saw. Cord
must be heavy enough to carry current
needed. An undersized cord will cause volt-
age drop at saw. Saw will lose power and
overheat. Follow cord size requirements
listed below.
Alwayscheckoillevelbeforeusingsaw. To
oil chain, press squeeze bulb on oil cap. Do
notattempttooperatetheoilerwhilecutting
with the saw. Oil will feed onto guide bar
and chain. Press squeeze bulb on oil cap at
least once before each cut. Check oil level
often by looking at oil sight level hole. Oil
sight level hole is on left side of saw, be-
tween front handle and front hand guard.
6. When starting a cut, place moving
chain against wood. Hold saw firmly
in place to avoid possible bouncing or
skating (sideways movement) of saw.
Cord Length
25 feet
AWG Cord Size
16 AWG
7. Guide saw using light pressure. Do not
force saw. The motor will overload and
can burn out. It will do the job better
and safer at the rate for which it was
intended.
50 feet
16 AWG
100 feet
16 AWG
8. Remove saw from a cut with saw run-
ning at full speed. Stop saw by releas-
ing trigger. Make sure chain has
stopped before setting saw down.
150 feet
14 AWG
Models LNT-2: 076728K, 099178H,
100089-06, & 100089-08; Pole Saw Assy
104317&106821;PoleSaw104316-04(8")
& 106890 (10")
9. Practice until you can maintain a steady,
even cutting rate.
Cord Length
25 feet
AWG Cord Size
16 AWG
Switch
Lockout
Figure 8 - Pressing Squeeze Bulb on Oil
Cap to Oil Chain
50 feet
16 AWG
100 feet
14 AWG
150 feet
12 AWG
ModelsEL-7:075762J,098013J,099039J,
100089-04, 100089-05, & 100089-07
Trigger
Figure 9 - Switch Lockout and Trigger
Location
107990
8
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER’S MANUAL
Direction
of Fall
OPERATING CHAIN
Retreat
Path
SAW
Hinge
Direction
of Fall
3rd Cut -
Felling Cut
Continued
2nd Cut -
Upper
Notch Cut
FELLING A TREE
(Cutting Down a Tree)
2
Inches
45°
2"
WARNING:
1st Cut -
Lower
Notch Cut
Retreat
Path
Tree
• Avoid kickback. Kickback can
resultinsevereinjuryordeath.
See Kickback, page 3 to avoid
risk of kickback.
Figure 10 - Retreat Path From Tree
Felling Procedure
A) Felling Notch
• Donotfellatreewithoutample
skill or expert help.
• Keep children, animals, and
bystanders away from area
when felling a tree.
• If two or more persons perform
bucking and felling operations
A properly placed felling notch will deter-
mine direction tree will fall. Place felling
notch on side of tree in direction you want
tree to fall (see Figure 11). Follow direc-
tions below to create a felling notch.
Figure 11 - Felling A Tree
3. As felling cut nears hinge, tree should
begin to fall. Note: If needed, drive
wedges into felling cut to control direc-
tion of fall. If tree settles back and pinches
chain, drive wedges into felling cut to
remove saw. Only use wedges made of
wood, plastic, or aluminum. Never use
wedge made of steel. This could cause
kickback and damage to chain.
1. Make lower notch cut as close to
ground as possible. Hold saw so guide
bar is horizontal. Cut 1/3 the diameter
of tree trunk (see Figure 11). Note:Al-
ways make this horizontal lower notch
cut first. If you make this cut second,
tree can pinch chain or guide bar.
WARNING: When felling a
tree, be aware of your surround-
ings. Do not endanger any per-
son, strike utility lines, or cause
property damage. If tree strikes
utility lines, contact utility com-
pany at once.
4. When tree begins to fall, quickly
• remove saw from felling cut
• release trigger to turn saw off
• put saw down
2. Start upper notch cut the same distance
above first cut as first cut is deep.
Felling is the process of cutting down a tree.
Make sure your footing is firm. Keep feet
apart. Divide your weight evenly on both
feet. Follow directions below to fell a tree.
Example: If lower notch cut is eight
inches deep, start upper notch cut eight
inches above it. Cut downward at 45°
angle. The upper notch cut should meet
end of lower notch cut (see Figure 11).
• exit area using retreat path
WARNING: Be alert for falling
overheadlimbs.Watchyourfoot-
ing while exiting area.
Before Felling a Tree
3. Remove tree trunk wedge created by
notching cuts.
1. Before felling, inspect tree. Make sure
there are no dead limbs or branches that
may fall on you. Study natural lean of
tree, location of larger branches, and
B) Felling Cut
wind direction. This will help you judge 1. Make felling cut two inches higher than
which way tree will fall.
lower notch cut and on opposite side
of tree (see Figure 11). Keep felling cut
parallel to lower notch cut.
2. Clear work area around tree.
3. Plan and clear a retreat path before fell-
ing. Make retreat path opposite to
planned direction of fall of tree and at
45° angle (see Figure 10).
4. Remove dirt, stones, loose bark, nails,
staples, and wire from tree where you
will make felling cuts.
2. Cut towards notch.
WARNING: Do not cut all the
way through tree. Leave about
two inches of tree diameter un-
cut directly behind felling notch
(see Figure 11). This uncut por-
tion acts as a hinge. The hinge
helpskeeptreefromtwistingand
falling in wrong direction.
5. Stay on uphill side when felling tree.
Tree could roll or slide downhill af-
ter falling.
Continued
107990
9
Download from Www.Somanuals.com. All Manuals Search And Download.
®
ELECTRIC CHAIN SAW
Entire Length Of Log On
Ground
Cut log from top (see Figure 13).
BUCKING A LOG
OPERATING CHAIN
SAW
WARNING: Avoid kickback.
Continued
Kickback can result in severe in-
juryordeath.SeeKickback,page
3 to avoid risk of kickback.
LIMBING A TREE
WARNING: Avoid kickback.
WARNING:
Kickback can result in severe in-
juryordeath.SeeKickback,page
3 to avoid risk of kickback.
• If on slope, make sure log will
not roll down hill. Secure log
byusingwoodenstakes. Drive
wooden stakes into ground on
downhill side of log. Stand on
uphill side of log while cutting.
Log may roll after cutting.
• Never try cutting through two
logs at same time. This could
increase the risk of kickback.
• While cutting log, never hold
logwithyourhand,leg,orfoot.
• While cutting log, never allow
another person to hold log.
• Turn off and unplug saw be-
fore moving from one place to
another.
WARNING:Whencuttinglimb
thatisundertension,useextreme
caution.Bealertforwoodspring-
ing back. When wood tension is
released, limb could spring back
and strike operator causing se-
vere injury or death.
Figure 13 - Bucking Log With Entire
Length On Ground
Limbingisremovingbranchesfromafallen
tree. Make sure your footing is firm. Keep
feet apart. Divide your weight evenly on
both feet. Do not remove larger limbs under
tree that support log off ground. Remove
each limb with one cut (see Figure 12).
Clear cut limbs from work area often. This
will help maintain a safe work area.
Log Supported On One End
1. Make first cut on underside of log (see
Figure 14). Use top of guide bar to
make this cut. Cut 1/3 through diam-
eter of log. This cut will keep section
from splintering when cut.
Bucking a log is cutting a log into sections.
Make sure your footing is firm. Keep feet
apart. Divide your weight evenly on both feet.
Whenpossible,raiselogorsectionoffground.
Do this by using limbs, logs, chocks, etc.
2. Make second cut directly above first
cut. Cut down to meet first cut. This
cut will keep log from pinching guide
bar and chain.
Make sure you start your cut where limb
will not pinch saw during cutting. To avoid
pinching, start cut on freely hanging limbs
from above limb. Start cut on limbs under
tension from under limb. If pinch occurs,
turn saw off, lift limb, and remove saw.
When cutting through log, maintain control
byreducingcuttingpressurenearendofcut.
Donotrelaxyourgriponchainsawhandles.
Do not let moving chain touch ground.
Ground will dull moving chain. After cut-
ting through log, release trigger to turn saw
off before moving saw.
2nd Cut
Follow directions below to buck a log.
1st Cut
Figure 14 - Bucking Log When Log Is
Supported On One End
Figure 12 - Limbing A Tree
107990
10
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER’S MANUAL
2nd Cut -
Pruning Cut
(to avoid pinching)
TRIMMING A TREE (Pruning)
OPERATING CHAIN
4th Cut -
Final Stub
Cut
SAW
WARNING: Avoid kickback.
Kickback can result in severe in-
juryordeath.SeeKickback,page
3 to avoid risk of kickback.
Continued
Log Supported On Both Ends
1. Make first cut from above log (see Fig-
ure 15). Cut 1/3 through diameter of
log. This cut will keep section from
splintering when cut.
6"
WARNING: Do not operate
chain saw while
• in a tree
• on a ladder or any other un-
stable surface
• in any awkward position
Youmaylosecontrolofsawcaus-
ing severe injury.
2" to 4"
2. Make second cut on underside of log,
directly under first cut. Use top of guide
bar to make this cut. Cut up to meet
first cut. This will keep log from pinch-
ing guide bar and chain.
1st Cut -
Pruning Undercut
(to avoid splintering)
3rd Cut - Stub Undercut
(to avoid splintering)
WARNING: Do not cut limbs
higher than your shoulders.
1st Cut
Figure 16 - Cutting A Limb
CAUTION: Seek professional
help if facing conditions beyond
your ability.
Trimming a tree is the process of cutting
limbs from a living tree. Make sure your
footing is firm. Keep feet apart. Divide your
weight evenly on both feet. Follow direc-
tions below to trim a tree.
1. Make first cut six inches from tree trunk
on underside of limb. Use top of guide
bar to make this cut. Cut 1/3 through
diameter of limb (see Figure 16).
2nd Cut
Figure 15 - Bucking Log When Log Is
Supported On Both Ends
2. Move two to four inches farther out on
limb. Make second cut from above limb.
Continue cut until you cut limb off.
3. Make third cut as close to tree trunk as
possible on underside of limb stub. Use
top of guide bar to make this cut. Cut
1/3 through diameter of stub.
4. Make fourth cut directly above third
cut. Cut down to meet third cut. This
will remove limb stub.
107990
11
Download from Www.Somanuals.com. All Manuals Search And Download.
®
ELECTRIC CHAIN SAW
Normal Guide Bar Maintenance
1. Remove guide bar from chain saw.
CARE OF GUIDE BAR
CLEANING AND
MAINTENANCE
Uneven bar wear causes most guide bar
problems. Incorrect sharpening of chain
cutter and depth gauge settings often cause
this. When bar wears unevenly, it widens
guidebargroove(seeFigure17).Thiscauses
chainclatterandrivetpopping. Sawwillnot
cutstraight.Replaceguidebarifthisoccurs.
2. Remove sawdust from guide bar
groove periodically. Use putty knife or
wire.
NOTICE: Below are instructions
forservicingyourchainsaw.Any
servicing not mentioned below
should be done by an authorized
service center.
3. Clean oil slots after each day of use.
4. Remove burrs from sides of guide bar.
Use flat file to make side edges square.
Inspect guide bar before sharpening chain.
A worn or damaged guide bar is unsafe. A
worn or damaged guide bar will damage
chain. It will also make cutting harder.
Replace guide bar when
• bar is bent or cracked
CLEANING SAW BODY
• inside groove of bar is badly worn
WARNING: Unplug chain saw
from power source before servic-
ing. Severe injury or death could
occur from electrical shock or
body contact with moving chain.
Note: When replacing guide bar, see Re-
placement Parts and Accessories, page 19,
for proper bar.
Guide Bar
Groove
Burr
WARNING: Cutting edges on
chain are sharp. Use protective
gloves when handling chain.
Guide Bar
WARNING: When cleaning
saw body,
• do not submerge saw in any
liquids
Flat File
• do not use products that con-
tain ammonia, chlorine, or
abrasives
• do not use chlorinated clean-
ingsolvents,carbontetrachlo-
ride, kerosene, or gasoline
Guide Bar
Guide Bar
With Uneven
Normal Guide
Cleaning Groove With
Putty Knife
Bar
Wear
Figure17-GuideBarCrossSectionShow-
ing Uneven Bar Wear
Keepsawbodyclean.Useasoftclothdamp-
ened with a mild soap and water mixture.
Wipe saw body to clean.
Oil Slot
Figure 18 - Guide Bar Maintenance
107990
12
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER’S MANUAL
4. Hold file guide level. Make sure 30°
mark on file guide is parallel to center
of guide bar (see Figure 19). This will
Sharpening Cutters
CLEANING AND
Use file guide for 30° filing.
1. Adjust chain for proper tension (see Saw
Chain Tension Adjustment, page 7).
MAINTENANCE
insure that you file cutters at 30° angle.
Continued
5. File from inside towards outside of cut-
ter until sharp. Only file in this one direc-
tion (see Figure 19). Note: Two or three
strokes with file should sharpen cutter.
2. Clamp guide bar in vise to hold saw
SHARPENING SAW CHAIN
steady. Note: Do not clamp chain.
3. Press 5/32" round file (attached to file
guide) into groove between top plate
and depth gauge on chain. File guide
should rest on both top plate and depth
gauge (see Figures 19 and 20). Note:
File at midpoint of guide bar.
WARNING: Unplug chain saw
from power source before servic-
ing. Severe injury or death could
occur from electrical shock or
body contact with moving chain.
6. After each cutter is sharpened, move
chain forward to sharpen next cutter.
File all cutters on one side of chain.
7. Move to other side of chain and repeat
process.
Filing
Direction
WARNING: Cutting edges on
chain are sharp. Use protective
gloves when handling chain.
30° Guide
Mark
File
Guide
Keep chain sharp. Your saw will cut faster
and more safely. A dull chain will cause
undue sprocket, guide bar, chain, and motor
wear. If you must force chain into wood and
cutting creates only sawdust with few large
chips, chain is dull.
5/32"
Round File
Items Needed to Sharpen Chain
Purchasetheseitemsfromyourlocaldealer,
hardwarestore,orchainsawsuppliesoutlet.
Note: This illustration
shows file guide
placement and filing
direction for sharpen-
ing cutters on left side
of chain.
• 5/32" round file
• Depth gauge tool
• File guide
• Vise
• Medium sized flat file
Figure 19 - File and File Guide Placement On Chain
Groove
Depth Gauge
(left side of chain)
Left Side of
Chain
Depth Gauge
(right side
of chain)
Groove
Top Plate
(right side of chain)
Top Plate
(left side of chain)
Right Side of
Chain
Figure 20 - Chain Part Locations
Continued
107990
13
Download from Www.Somanuals.com. All Manuals Search And Download.
®
ELECTRIC CHAIN SAW
Front Corner
CLEANING AND
TECHNICAL
SERVICE
You may have further questions about as-
sembling,operating,ormaintainingthissaw.
If so, contact DESA International’s Techni-
cal Service Department at 1-800-858-8501.
.025"
MAINTENANCE
Continued
Filing Cutter Depth Gauges
Figure 22 - Round Off Front Corner Of
Depth Gauge
The cutter depth gauge clearance is reduced
as cutters are sharpened. After every second
orthirdsharpening,resetcutterdepthgauges.
You can also visit DESA International’s
technical service web site at
REPLACING SAW CHAIN
1. Place depth gauge tool (.025") firmly
across top of two cutters. Make sure
depth gauge enters slot in depth gauge
tool (see Figure 21).
Replace chain when cutters are too worn to
sharpen or when chain breaks. Only use
replacement chain noted in this manual.
Always include new drive sprocket when
replacing chain. This will maintain proper
drivingofchain.Note:Forproperchainand
drive sprocket, see Replacement Parts and
Accessories, page 19.
SERVICE
PUBLICATIONS
You can receive an illustrated parts list free
of charge. Send a self-addressed stamped
envelope to address on back page of this
manual.
2. Use medium flat file. File depth gauge
level with depth gauge tool.
3. Remove depth gauge tool. With flat file,
round off front corner of cutter depth
gauge (see Figure 22).
After several hand filings, have authorized
servicecenterorsharpeningservicemachine
sharpen chain. This will insure even filing.
When writing, include model number and
serial number of saw. You will find these
numbers on saw motor housing decal.
STORAGE
If storing saw for more than 30 days, follow
steps below.
Flat File
1. Drain oil tank.
Depth Gauge
2. Remove and clean guide bar and chain.
Clean guide bar and chain by soaking
in petroleum based solvent or mild soap
and water mixture.
3. Dry guide bar and chain.
Depth
Gauge
Tool
4. Place chain in container filled with oil.
This will prevent rust.
5. Wipe a thin coating of oil over surface
of guide bar.
6. Wipe off outside of saw body. Do this
with soft cloth dampened with a mild
soap and water mixture.
Depth
Gauge
Slot
7. Store chain saw
• in a high or locked place, out of
children’s reach
• in a dry place
Figure 21 - Depth Gauge Tool On Chain
• in a carrying case or with scabbard
over guide bar
107990
14
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER’S MANUAL
TROUBLESHOOTING
Note: For additional help, visit DESA
International’stechnicalservicewebsite
WARNING: Unplug chain saw from power source before servicing.
Severe injury or death could occur from electrical shock or body contact
with moving chain.
OBSERVED FAULT
POSSIBLE CAUSE
REMEDY
Saw runs, but does not cut
Chain assembled backwards on guide bar
See Assembly, page 6
Saw does not cut unless heavily forced. Chain is dull
Cutting produces only sawdust with few
large chips
See Sharpening Saw Chain, page 13
Saw runs slow. Saw stalls easily
Low power supply voltage
Extension cord wire size too small. See
Extension Cords, page 8
Motorofsawdoesnotrunwhenyousqueeze 1. Switch lockout not pressed in to release 1. Press in switch lockout before squeez-
trigger
trigger
ing trigger
2. Extension cord connections loose
3. Open line fuse or circuit breaker
4. Bad motor brushes
2. Check cord connections
3. Check line fuse or circuit breaker
4. See authorized service center
5. See authorized service center
5. Open wiring circuit on saw
Motor of saw runs, but chain does not move Gear train failure
See authorized service center
Chain does not get oil
1. Clogged oil slot in guide bar
2. Oil is too thick
1. Remove guide bar and clean oil slot
2. Use correct weight of oil. See Filling Oil
Tank, page 7
Chain comes off guide bar
1. Chain is loose
1. Tighten chain. See Saw Chain Tension
Adjustment, page 7
2. Guide bar and chain not assembled right 2. See Assembly, page 6
Saw smokes
Saw leaks oil
Saw damaged. Do not use saw
Oil cap is not secure
See authorized service center
Tighten oil cap. Note: Empty oil tank when
not in use
107990
15
Download from Www.Somanuals.com. All Manuals Search And Download.
®
ELECTRIC CHAIN SAW
ILLUSTRATED
PARTS
BREAKDOWN
LNT-2
19
13
5
6
18
1
21
26
2
16
21
9
14
10
7
3
12
4
23
15
24
11
17
20
22
22
20B
20B
8
25
20
22
Shoulder Screw Installation
E-Ring Installation
Installing Shoulder Screw or E-Ring
Depending On Model
107990
16
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER’S MANUAL
Thislistcontainsreplaceablepartsusedinyourchainsaw.Whenorderingparts,besuretoprovidethecorrect
model and serial numbers (from the model plate), then the part number and description of the desired part.
PARTS LIST
LNT-2
QTY.
KEY
NO.
PART
NO.
100089-06 107709-01
099178H 100089-08 076728K
DESCRIPTION
__
__
1
097568-01
097570-01
091373-02
091374-02
107481-01
075676
Guide Bar, 12"
Guide Bar, 14"
Saw Chain
1
__
1
__
1
__
2
1
__
Saw Chain
1
1
1
2
1
1
1
1
2
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
2
10
1
1
3
4
5
6
7
8
9
Armature Assembly
Sprocket Roller Bearing
Hex-Head Bolt
Cap & Bulb Assembly
Cord
Side Cover, Black
Thrust Disk
Field & Brush Assembly
Drive Gear
1
1
2
1
1
__
076744
107512-01
099829-01
077399-02
076105
107482-01
059606
1
__
1
1
1
1
1
1
2
1
1
1
1
1
1
2
10
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
2
10
1
1
1
10
11
12
13
14
15
16
17
18
19
20
20B
21
22
23
24
25
26
075752
Internal Gear
106809-01
079089-02
NPC-4C
077115
075887
079086-02
097403-01
076905
109920-01
076906
059046
077143
077525S
106810-01
079963-02
079963-04
Front Hand Guard
Motor Housing, Black
Hex Nut
Adjusting Plate Assembly
Bearing Plate
Oil Reservoir
Pan-Head Screw
Pan-Head Shoulder Screw
E-Ring
Flat-Head Tap Screw
Pan-Head Tap Screw
Sprocket Support
Lock-Off Switch
Sprocket Cover, Black
Scabbard
1
__
1
__
1
__
Scabbard
1
1
107990
17
Download from Www.Somanuals.com. All Manuals Search And Download.
®
ELECTRIC CHAIN SAW
ILLUSTRATED
PARTS
BREAKDOWN
EL-7
26
14
22
13
5
9
25
3
6
18
21
2
17
21
1
4
16
10
15
27
11
20B
20
23
7
24
19
12
8
20B
19
20
Shoulder Screw Installation
E-Ring Installation
Installing Shoulder Screw or E-Ring
Depending On Model
107990
18
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER’S MANUAL
Thislistcontainsreplaceablepartsusedinyourchainsaw.Whenorderingparts,besuretoprovidethecorrect
model and serial numbers (from the model plate), then the part number and description of the desired part.
PARTS LIST
EL-7
QTY.
098031J
099039J
KEY
NO.
075762J
100089-07
100089-05
107714-02
PART NO.
DESCRIPTION
__
1
097570-01
097572-01
091374-02
091375-02
100933-01
075676
Guide Bar, 14"
Guide Bar, 16"
Saw Chain
Saw Chain
Armature
Sprocket Roller Bearing
Hex-Head Bolt
Oil Reservoir Cap
Cord
Side Cover, Black
Field
1
__
1
__
2
1
__
1
1
1
2
1
1
1
1
1
1
1
1
1
1
2
1
1
6
1
1
2
1
1
1
1
1
4
3
4
5
6
7
8
9
1
1
2
1
1
1
1
1
1
1
1
1
1
2
1
1
6
1
1
2
1
1
1
1
1
4
076744
107512-01
099829-01
077399-02
098042-01
059606
10
11
12
13
14
15
16
17
18
19
20
20B
21
22
23
24
25
26
27
Drive Gear
Internal Gear
075752
106810-01
106809-01
076053
097034-02
NPC-4C
077115
079086-02
059046
076905
109920-01
076906
097403-01
077143
077525S
058059
Sprocket Cover
Front Hand Guard
Motor Housing Assembly
Housing Assembly
Hex Nut
Adjusting Plate Assembly
Oil Reservoir
Pan-Head Tap Screw
Pan-Head Shoulder Screw
E-Ring
Flat-Head Tap Screw
Pan-Head Screw
Sprocket Support
Lock-off Switch
Thrust Washer
Scabbard
079963-04
059045
Pan Head Tap Screw
PARTS AVAILABLE - NOT SHOWN
079882-09
Hardware Package
Includes: 2 - NPC-4C Nuts
2 - 076744 Bolts
1
1
1 - 097403-01 Screw
107990
19
Download from Www.Somanuals.com. All Manuals Search And Download.
®
ELECTRIC CHAIN SAW
PARTS DEALERS
Ray’s Portable Heater Service
3191 Myers Road
Camino, CA 95709-9550
530-644-7716
Portable Heater Parts
Hance Distributors, Inc.
Bortz Chain Saw Shop
Webbs Appliance Center
1519 Church Street
Nashville, TN 37203-3004
615-329-4079
342 North County Road 400 East
Valparaiso, IN 46383-9704
219-462-7441
12795 16th Avenue North
Plymouth, MN 55441-4556
763-559-2299
Road #2, Box 64A
Oley, PA 19547-9412
610-987-6452
1-800-362-6951
1-800-899-4079
21st Century
Baltimore Electric
1348 Dixwell Avenue
Hamden, CT 06514-0322
203-248-7553
Automotive Equipment Service
3117 Holmes
Kansas City, MO 64109-1716
816-531-9144
2950 Fretz Valley Road
Perkasie, PA 18944-4034
215-795-0400
Industrial Hardware
4109 Bainbridge Blvd.
Chesapeake, VA 23324-1403
804-543-2232
FBD
1-800-325-4828
1-800-397-7553
1349 Adams Street
Bowling Green, KY 42103-3414
270-846-1199
1-800-654-8534
1-800-843-3546
1-800-788-0008
Laportes
Eckley’s Small Engine
31617 Spruce Drive
Eustis, FL 32726-9592
352-357-6764
2444 N 5th Street
Hartsville, SC 29550-7704
843-857-0222
Bowden Electric Motor Service
1681 S. Wesleyan Blvd.
Rocky Mount, NC 27803
252-446-4203
Mills Lawn and Garden
928 Commonwealth Place
Virginia Beach, VA 23464
757-361-9293
Parts Company of America
1657 Shermer Road
Northbrook, IL 60062-5362
708-498-5900
1-800-323-0620
MTA Distributors
Lyons & Lyons Sales Co. Inc.
Glen Arm Road
Glen Arm, MD 21057-9454
410-665-6500
1-800-333-5966
(Generators ONLY)
555 Hickory Hills Blvd.
Nashville, TN 37189-9244
615-259-8777
East Coast Energy
707 Broadway
West Long Branch, NJ 07764-1542
1-800-755-8809
Tuco Industrial Products
5223 180th Street SW
Suite 4A-1
Lynnwood, WA 98037-4506
425-743-9533
1-800-264-0225
Forrest Lytle and Sons, Inc.
740 West Galbraith Road
Cincinnati, OH 45231-6002
513-521-1464
Master Part Distributors
1251 Mound Avenue NW
Grand Rapids, MI 49504-2672
616-791-0505
1-800-735-1268
1-800-446-1446
AUTHORIZED SERVICE CENTERS
ALABAMA (AL)
California Electric Service
2594 East Colorado Blvd.
Pasadena, CA 91107
626-792-3194
AAA Electric Company, Inc.
24 South Main Street
Longmont, CO 80501
330-776-6031
A1A Small Engines & Equipment
420 S. Dixie Hwy. E.
Tifton Electric Motors
1265 US Hwy. 82E
Tifton, GA 31794
912-382-4040
A & O General Repair Service
1470 Opelika Road
Auburn, AL 36830
334-821-7022
Pompano Beach, FL 33060
954-946-5044
West Coast Contractors Supply
#28 13th Street
San Francisco, CA 94103
415-861-6124
Dales Electric Motor Repair
932 Coffman Street
Longmont, CO 80501
303-651-6907
Mulvaney’s Inc.
IDAHO (ID)
Southern Power Tool
2824 Cottage Glen Dr.
Mobile, AL 36693
334-639-8188
2148 W. Tennessee Street
Tallahassee, FL 32304
850-576-5578
Rossiter Electric
1501 S. Capitol Ave.
Idaho Falls, ID 83403
208-529-3665
Leete Electric Company
930 Petaluma Hill Road
Santa Rosa, CA 95404
707-545-0484
CONNECTICUT (CT)
Baltimore Electronics
5 Manila Ave.
Hamden, CT 06514
203-248-7553
A-1 Tool Rental, Inc.
2509 South State Road 7
West Hollywood, FL 33023
954-961-9250
ARIZONA (AZ)
Steam Store Rocky Mountain, Inc.
155 North Gate Mile
Idaho Falls, ID 83401
208-522-0609
Best Brothers Lawnmower Repair
5549 W. Glendale Avenue
Glendale, AZ 85301
602-939-9170
Rincon Valley Yard & Garden
4972 Sonoma Hwy
Santa Rosa, CA 95409
707-593-4124
GEORGIA (GA)
1-800-397-7553
Hamilton Hardware
5300 Veterans Pkwy.
Columbus, GA 31904
706-322-6545
J & J Enterprises
D & L Small Engines, Inc.
10023 North 19th Ave.
Phoenix, AZ 85021
602-861-1978
Utility Electric Service
53 Main Street
Hartford, CT 06106
860-246-7271
1704 Addison Avenue East
Twin Falls, ID 83301
208-733-2001
California Electric Service
14753 Oxnard Street
Van Nuys, CA 91411
818-997-8855
Cowan Ace Hardware
1264 Green Street
Conyers, GA 30207
770-483-8818
ILLINOIS (IL)
Power Tool Service Center
660 East 19th Street
Tucson, AZ 85719
520-884-8974
Goodies Sales and Service
133 Hamilton Street
New Haven, CT 06515
203-865-1470
Uline Lawn Equipment
290 W. Squk Trail
Chicago Heights, IL 60411
708-755-2227
Power Outdoor Equipment
3160 Industrial Drive
Yuba City, CA 95993
530-671-1871
Able Tool Rental
708-755-1533 (Fax)
CALIFORNIA (CA)
Ray’s Portable Heater Service
3191 Meyers Road
Camino, CA 95709
530-644-7716
FLORIDA (FL)
3360 Fairburn Road
Douglasville, GA 30135
770-949-1932
301 Mower Shop
5724 15th Street E.
Bradenton, FL 34203
941-758-7844
Lange Electric
912 E. Fayette
Effingham, IL 62401
217-347-7626
COLORADO (CO)
McGuckin Power Equipment Center
2845 Valmont Road
Boulder, CO 80302
303-443-9317
Douglasville Ace Hardware
6530 Church Street
Douglasville, GA 30133
770-942-7044
California Electric Service
612 South Shoppers Lane
Covina, CA 91723
Eckley’s Small Engine
31617 Spruce Drive
Eustis, FL 32736
352-357-6764
Carter’s Small Engine Repair
206 N. Hickory Street
Galatia, IL 62935
Ace Mower and Small Engines
4718 Chromium Drive
Colorado Spring, CO 80918
719-593-0862
ASAP Equipment Services
3560 C Buford Hwy
Duluth, GA 30096
678-584-5462
818-915-4935
618-268-4814
California Electric Company
1208 East Ash Avenue
Fullerton, CA 92631
714-870-0900
Al’s Small Engine, Inc.
2496 Blanding Blvd.
Middleburg, FL 32068
904-282-5472
H & R Pump Company, Inc.
2111 E. Washington Street
Joliet, IL 60434
Bartell Tool Service
1448 W. Cedar Avenue
Denver, CO 80223
303-777-5463
Fayette Mower & Appliance
395 S. Glynn St.
Fayetteville, GA 30215
770-461-9400
815-726-2950
J & N Garden Equipment
4460 W. Imperial Hwy.
Inglewood, CA 90304
310-671-0079
Lindle & Sons Electric Motor Repair
7016 Hwy. 22
INDIANA (IN)
Hutchens Sales and Service
R.R. #5, Box 550
Bloomfield, IN 47424
812-876-1891
Panama City, FL 32401
850-871-1722
Metrogas Equipment Company
790 West 64th Ave.
Denver, CO 80221
303-428-3036
S & P Rental & Supply Co.
259 Grayson Hwy
Lawrenceville, GA 30245
770-963-0392
Shamay's Enterprises
P.O. Box 3714
58643 Knox-Niman Lane
Landers, CA 92285
760-364-2046
Eustis and Sons, Inc.
7035 66th Street North
Pinellas Park, FL 34665
727-544-1486
Nichols Ice & Oil
2018 Park Road
Connersville, IN 47331
765-825-3741
Winfrey’s Jones LLP
317 8th Street
Greeley, CO 80631
970-353-9576
Spray Solutions
476 Flowing Wells Rd. D-1
Martinez, GA 30907
706-855-1293
107990
20
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER’S MANUAL
B & W Repair Service
213 N. Main Street
Dale, IN 47523
E-Z Rent It Inc.
MASSACHUSETTS (MA)
Ormond’s Inc.
115R Dean Ave.
Franklin, MA 02038
508-528-2013
MISSOURI (MO)
Capitol Service & Equipment
551 New Market Road
Piscataway, NJ 08855
732-968-5577
1428 U.S. 31-W By-Pass
Bowling Green, KY 42101
270-782-9462
Stewarts Enterprises
7631 NW Salebarn Road
Cameron, MO 64429
816-632-6578
812-937-2576
Industrial Motor & Electrical
Supply, Inc.
64466 State Road 19
Goshen, IN 46526
219-862-4044
Roman’s Repair Shop
601 College Street
Bowling Green, KY 42101
270-746-0857
Air & Electric Tool Service, Inc.
130 W. 3rd Street
Roselle, NJ 07203
908-242-6930
Beacon Lumber/Beacon Rental
513 Church Street
New Bedford, MA 02745
508-995-1766
Northwest Power Sales
26848 Haultain Drive
Maryville, MO 64468
660-582-5080
Hopkinsville Electric Motor
704 W. 15th Street
Hopkinsville, KY 42240
270-886-7585
NEWYORK (NY)
Valley Mower Service
2857 Ellis Creek Road
Barton, NY 13734
607-589-4825
Tyrie Mower Repair
110 South 16th Street
Lafayette, IN 47905
765-742-7886
Mott’s Tool Repair Service
92 Rayber Road
Orleans, MA 02653
508-240-0764
Buchheit, Inc.
Route 7, Box 239
Perryville, MO 63775
573-547-1017
Maury’s Fluorescent Appliance
1521 Bardstown Road
Louisville, KY 40205
502-456-1671
Kabelin True Value Hardware
512 Andrew Avenue
Laporte, IN 46350
219-362-7917
Utility Electric Service #2
810 Main Street
Springfield, MA 01105
413-781-1635
A K Small Engine Works
15726 Hwy C
Versailles, MO 65084
573-378-6339
White Tool Supply Inc.
3047 Atlantic Avenue
Brooklyn, NY 11208
718-227-8844
Rental World, Inc.
9509 Dixie Hwy.
Louisville, KY 40272
502-935-8853
Lear Lawn & Garden
2204 N. Wolfe Street
Muncie, IN 47303
765-282-6273
MICHIGAN (MI)
R & A Service
12900 Haggerty Road
Belleville, MI 48111
734-697-1144
MONTANA (MT)
Lehman’s Farm & Home Supply
Route 26
Denmark, NY 13631
315-493-1151
Tom’s Service Repair
1111-6th Avenue North
Billings, MT 59101
406-259-6179
All States Industrial Repair
728 E. Center Street
Madisonville, KY 42431
270-821-6555
Li’l Engine Sales & Service, Inc.
1428 Vincennes Street
New Albany, IN 47150
812-944-1377
M & S Repair Shop
303 Hilltop Drive
Elma, NY 14059
716-652-0311
Thompson’s Rental Resale Repair
11973 New Lothrop Road
Byron, MI 48418
Mosch Electric Motors, Inc.
2513 - 17th St. NE
Black Eagle, MT 59414
406-453-2481
LOUISIANA (LA)
810-266-4969
Portable Heater Parts
342 North County Road, 400 East
Valparaiso, IN 46383
219-462-7441
Triangle Bicycle and Lawnmower
5433 Crowder Road
New Orleans, LA 70127
504-241-3239
Luther’s Outdoor Equipment
3676 State Route 5
Frankfort, NY 13340
315-894-4467
Hendricks Sales
7876 Division
Grand Rapids, MI 49548
616-455-8220
Sun Rental Center
1301 - 3rd St. NW
Great Falls, MT 59404
406-761-6688
D W Handy’s
Wayne’s Heat & Air
1605 W. Vine Street
Opelousas, LA 70570
337-948-4246
Crossbay Appliance Service
158-34 Crossbay Blvd.
Howard Beach, NY 11414
718-843-4422
217 West 15th St.
Vincennes, IN 47591
812-886-0172
Chicago Drive Rentals, Inc.
11298 Chicago Drive
Holland, MI 49424
616-396-9575
NEBRASKA (NE)
Hatten’s Electric Service
130 S. Hastings, Box 843
Hastings, NE 68901
402-463-4596
New Paris Farm Store
68443 W. Main Street
P.O. Box 96
New Paris, IN 46553
219-831-4823
Evans of LA, Inc.
Provenzano’s
907 Cypress Street
West Monroe, LA 71291
318-322-6180
Fowler’s Farm City Sales
2876 West Washington Road
Ithaca, MI 48847
84 E. Main Street
Kings Park, NY 11754
631-269-1080
Craft Specialties
201 Pine St.
Hadder, NE 68738
402-379-3129
989-875-3976
MAINE (ME)
Para-Deys Tools
708 Victor Road
Macedon, NY 14502
315-986-2520
IOWA (IA)
Richard’s Electric Motor
549 Main Street
Caribou, ME 04736
207-498-8950
Superior Industrial Sales & Service
116 N. State Street
Jackson, MI 49201
Beal’s Motor Rewinding
600 West Beach
Cherokee, IA 51012
712-225-6173
Flohr Electric Motor
4356 South 90th Street
Omaha, NE 68127
402-331-6863
517-784-0539
P & C
Roger’s Electric Motor Shop
823-West Main Street
Madawaska, ME 04756
207-728-4253
Norm’s Electric Motor Repair
414 Walbridge Street
Kalamazoo, MI 49007
616-382-5054
12 East Street
Nunda, NY 14517
716-468-5050
Blink Electric Motors
Rear 116 N. 1st Ave.
Marshalltown, IA 50158
641-752-3036
MSE Parts Unlimited
4935 South 136th Street
Omaha, NE 68137
402-895-0806
Otega Repair
Rent-N-Save
A & J Rentals
226 County Hwy 7
Otego, NY 13825
607-988-7859
Northeast Iowa Motor Service
24665-150th Street
Sumner, IA 50674
563-578-5883
28 Allen Avenue
Portland, ME 04103
207-797-2223
550 S. 11th Street
Niles, MI 49120
616-684-3200
Ted’s Mower Sales and Service, Inc.
5155 Q. Street
Omaha, NE 68117
402-731-7058
Owego Agway Coop
38 West Avenue
Owego, NY 13827
607-687-2039
MARYLAND (MD)
Bob’s Service Shop
2537 W. Drahner Road
Oxford, MI 48371
248-628-2601
Black Hawk Rental
324 West 15th Street
Waterloo, IA 50702
319-234-4421
Center Supply Company
6802 Industrial Drive #208
Beltsville, MD 20705
301-595-0860
LaVern Hass Repair
1204 - 1st Road
Wisner, NE 68791
402-529-6846
Jack-n-Heater Service
185 Beartown Road
Painted Post, NY 14870
607-962-1239
Bid’s Service, Inc.
11276 E. Ten Mile
Warren, MI 48089
586-759-3040
KANSAS (KS)
Lehmans Hardware, Inc.
5921 Belair Road
Baltimore, MD 21206
410-483-5888
NEW HAMPSHIRE (NH)
Kingston Enterprises
85 North Road
Kingston, NH 03848
603-642-3506
Abilene Rent-All & Sales
1701 West 1st Street
Abilene, KS 67410
785-263-7668
Larmon Small Engine
16353 Co. Rt. 91
Pierrepont Manor, NY 13674
315-465-6671
MINNESOTA (MN)
Norris Taylor Contractors, Inc.
8480 Ocean Gateway
Easton, MD 21601
410-822-2050
Perry’s Electrical Rebuilders
24664 Hale Avenue
Forest Lake, MN 55025
651-464-8054
NAAB Electric, Inc.
2013 W. Jones
Garden City, KS 67846
316-276-8101
NEW JERSEY (NJ)
Associated Industries
2433 Rt. 206
Eastampton, NJ 08060
609-267-8417
R & D Mower & Snowblower
Sales and Service
1632 Empire Blvd.
Webster, NY 14580
716-671-9409
Lyons & Lyons Sales Co. Inc.
Glen Arm Road
Glen Arm, MD 21057-9454
410-665-6500
1-800-333-5966
Andy’s Small Engine City
2408 Pearl Ct. SE
Rochester, MN 55904
507-280-0373
Morris Electric Repair
2423 5th Street
Great Bend, KS 67530
316-792-2919
Woodchuck’s Lawnmower
and Appliance
220 Whitehorse Pike
Magnolia, NJ 08049
856-783-1111
Bedford Appliance, Inc.
1173 Yonkers Ave.
Yonkers, NY 10704
914-237-7575
Reed’s Sales & Service
1260 Payne Ave.
St. Paul, MN 55101
651-774-9515
McPherson Rental Center
911 West First Street
McPherson, KS 67460
620-241-3333
Chesapeake Rent All
210 N. Stokes Street
Havre De Grace, MD 21078
410-939-1720
Tep’s Power Equipment
1002 N. High Street
Millville, NJ 08332
856-825-8294
NORTH CAROLINA (NC)
Harnett & Wake Sales & Service
44 N. Broad Street
Angier, NC 27501
919-331-0463
MISSISSIPPI (MS)
Handy Man Rentals
1904 Shiloh Road
Corinth, MS 38834
662-287-2460
KENTUCKY (KY)
Gillum’s Service & Repair
8611 Rt. US 60
Ashland, KY 41102
606-928-4932
B & M Sharpening & Repair
8614 Church Lane
Randalstown, MD 21133
410-655-0801
Richard’s Sharpening Service
824 Mill Road
Northfield, NJ 08225
609-641-9481
Leonard Electric Motor Repair, Inc.
531 N. Fayetteville St.
Asheboro, NC 27203
336-625-2375
107990
21
Download from Www.Somanuals.com. All Manuals Search And Download.
®
ELECTRIC CHAIN SAW
Martin Equipment Company
4209-B US 70 E.
Goldsboro, NC 27534
919-778-5996
United Rentals of North America
5745 Angola Road
Toledo, OH 43615
Raymond, M. Nolt
290 S. Shirk Road
New Holland, PA 17557
717-354-0198
Corpus Christi Power Tool & Rpr.
3701 Agnes
Corpus Christi, TX 78405
361-883-1117
WASHINGTON (WA)
Action Small Appliance Service
1500 - 145th Place SE
Bellevue, WA 98007
425-643-9806
419-865-5539
Hickory Home & Garden
336 HWY 321 NW
Hickory, NC 28601
704-327-3719
OKLAHOMA (OK)
Kay Electric Company
1101 W. Broadway
P.O. Box 635
Altus, OK 73522
580-482-1757
Snyder Electric Company
1500 Chateau Street
Pittsburgh, PA 15233
412-231-3100
Freel Enterprise
118 Elston
Dallas, TX 75232
214-376-9913
TUCO Industrial Products
5223 - 180th SW Suite 4A-1
Lynnwood, WA 98037
425-743-9533
O’Mary’s Small Engine
220 W. Forlines Road
Winterville, NC 28590
252-355-4597
Stamm’s Mower Repair
Rd. 5, Pine Lane Box 150
Selinsgrove, PA 17870
570-743-7651
Southwest Electric Service
3008 Canton St.
Dallas, TX 75226
214-742-8211
Action Small Appliance
2125 Second Avenue
Seattle, WA 98121
206-448-2020
Sooner Distributors
3021 S. High Street
Oklahoma City, OK 73143
405-634-3391
NORTH DAKOTA (ND)
Fix-It Shop
316 21st Street E.
Dickson, ND 58601
701-225-0766
SOUTH CAROLINA (SC)
Hall’s Small Motor Repair
225 Heathwood Drive
Aiken, SC 29803
Powell’s Small Engine Service
5906 Hwy 66
Greenville, TX 75402
903-454-1877
Lifficks Electric Shop
8239 S. Park Avenue
Tacoma, WA 98408
253-474-7403
H. L. Moss
1714 E. 15th Street
Tulsa, OK 74104
918-744-1305
803-649-6313
Home Appliance Services
1909 Reese Street
Liberty, TX 77575
409-336-8615
Ted’s Saw Service
901 South 12th Street
Grand Forks, ND 58201
701-775-7343
Todd’s Electric Motor Repair
110 Laurel Street
Conway, SC 29526
843-248-2444
WEST VIRGINIA (WV)
Beckley Mower Service
3695 Robert C. Byrd Drive
Beckley, WV 25802
304-253-5748
OREGON (OR)
Turner’s Lawnmower and Saw
728 SE Robin Way
Gresham, OR 97080
503-665-5441
Ray DeSpain’s Inc.
Craig’s Small Engine Repair
508 East 2nd Street
Williston, ND 58801
701-774-0798
Laportes
P.O. Box 184, Loop 494 North
New Caney, TX 77357
281-689-2121
2444 N. 5th Street
Hartsville, SC 29550
843-857-0222
Raymond’s Service Center
Route 65
Delbarton, WV 25670
304-475-2855
Pendleton Grain Growers
200 S. 1st Street
Hermiston, OR 97801
541-567-5591
Service Department
OHIO (OH)
Turner Repair Service
3 E. Belvue Road
Taylors, SC 29687
864-244-1746
UTAH (UT)
Carter Electrical Repair
3448 Lunar Rd. NE
Carrollton, OH 44615
330-627-4061
Roosevelt Service Center
133 South 300 East, Box 1546
Roosevelt, UT 84066
435-722-2119
Town and Country Supply
4117 First Avenue
Nitro, WV 25143
304-755-3520
Appliance Repair Central
3203 NE Sandy Blvd.
Portland, OR 97232
503-234-7339
TENNESSEE (TN)
Vista Small Engine
1510 Vista Lane
Clarksville, TN 37043
931-552-6953
North East Mower Service
412 East 156th Street
Cleveland, OH 44110
216-531-8197
Appliance Service Center
1475 S. Main Street
Salt Lake City, UT 84115
801-467-6361
WISCONSIN (WI)
Smith Petroleum Ltd.
217 N. Walworth
Darien, WI 53114
262-724-3206
PENNSYLVANIA (PA)
General Rental & Sales Center
Old Rt 1 & 41
Avondale, PA 19311
610-268-2825
Lefeld Welding & Steel Supply
600 N. Second Street
Coldwater, OH 45828
419-678-2397
Master Repair Service
239 Elmore Road
Crossville, TN 38555
931-484-2061
VERMONT (VT)
Brown and Roberts
182 Main Street
Brattleboro, VT 05301
802-257-4566
Ohnstad Power Equipment
12012 Center Hill Road
Darlington, WI 53530
608-776-3802
Bud’s Tractor and Mower Sevice
21 Bock Lane
Baden, PA 15005
724-869-7142
Dayton Hardware & Supply
16-32 N. Irwin Street
Dayton, OH 45404
513-258-3721
1-800-762-3426 Ohio only
The Speciality Shop
2300 East Magnolia Avenue
Knoxville, TN 37917
865-523-6894
VIRGINIA (VA)
Bob’s Engine Shop
513 S. Military Road
Fond Du Lac, WI 54935
920-921-2841
Engine Doctors
20 Russell Blvd.
Bradford, PA 16701
814-362-3091
Industrial Hardware
4109 Bainbridge Blvd.
Chesapeake, VA 23324
804-543-2232
Authorized Equipment Service
812 Polk Avenue
Memphis, TN 38126
901-774-0850
Ken’s Repair
Reliance Electric Motors
1621 Livingstone Road
Hudson, WI 54016
715-386-3633
3246 S. Sectionline
Delaware, OH 43015
740-369-4798
Pro-Fix
Warren E. Smith Shops
406 Cambria Street
Christiansburg, VA 24073
540-382-5501
136 Narrows Road
Edwardsville, PA 18651
570-288-0476
Webb’s Appliance Service Center
1519 Church Street
Nashville, TN 37203
615-329-4079
Anytool & Outdoor Power Equip.
21150 Lorain Road
Fairview Park, OH 44126
440-356-1920
Kewaunee Small Engine
E2068 State Hwy 29
Kewaunee, WI 54216
920-388-2604
Carson’s Hardware
637-43 Main Street
Hellertown, PA 18055
610-838-7741
B & B Appliance & Lawn Equipment
71 Lawson Road SE Suite C
Leesburg, VA 22075
TEXAS (TX)
703-777-1093
Deep Run Mower Service
58781 Heil Addn. Deep Run
Martins Ferry, OH 43935
740-859-6131
Sacate Vedre, Inc.
1906 N. Western
Amarillo, TX 79106
806-373-4409
Ken’s Economy Sales
8887 Highway A
Marshfield, WI 54449
715-676-2143
Al Muccioli’s Service
2001 Bedford Street
Suite C
Johnstown, PA 15904
814-266-5734
Roberts Small Engine Repair
1109 Curve Road
Pearisburg, VA 24134
540-921-3255
Worcester Sales and Service
34200 Lorian Road
N. Ridgeville, OH 44039
440-327-2196
Industrial Distributing Co.
9411 Neils Thompson Dr.
Austin, TX 78759
Cliff’s Tractor Place
Hwy 35-133
P.O. Box 76
Patch Grove, WI 53817
608-994-2354
American Power Equip. Ctr.
2381 Staples Mill Road
Richmond, VA 23230
804-354-5810
0Valray Nurseries Inc.
R.D. #8, Box 362
Kittanning, PA 16201
724-548-1579
361-837-4122
Leonard Hardware
145 North 15th Street
Sebring, OH 44672
330-938-6329
Brunson Feed Mill
709 Sealy Ave.
Ballinger, TX 76821
915-365-2419
Outdoor Power Equipment
800 White Marsh Road
Suffolk, VA 23434
Barton Small Engine
1628 N. Main Street
West Bend, WI 53090
262-334-5373
Hillyard Equipment Service Center
633 Lausch Lane
Lancaster, PA 17601
717-569-5768
804-925-4933
Sparks Sales & Service
5184 Fletcher Chapel Road
Springfield, OH 45502
937-323-5925
Bud’s LP Gas & Supply
225 Grand
Channelview, TX 77330
713-457-2456
Mills Repair Service
928 Commonwealth Place
Virginia Beach, VA 23464
757-361-9293
Petrosky’s Hardware & Supply Co.
602 Alexandria Street
Latrobe, PA 15650
724-537-3541
107990
22
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER’S MANUAL
REPLACEMENT
PARTS AND
WARNING: Use only replacement parts and accessories described in
this manual. Use of other parts or accessories could damage saw or
injure operator.
ACCESSORIES
Purchase these accessories and parts from
your nearest dealer or service center. If they
can not supply these accessories or parts,
either contact your nearest Parts Dealer or
DESA International for referral informa-
tion. Parts dealers are listed in this manual.
You can also visit DESA International’s DESA International
technical service web site at P.O. Box 90004
Bowling Green, KY 42102-9004
1-800-858-8501
LNT-2
EL-7, 098031J, 099039J, 100089-04, POLE SAW, 106890-01 (10")
Part Number Description
100089-05
POLE SAW ASSEMBLY, 106821
Part Number Description
104302-01S#
104301S#
097567-01S
Guide bar, 8"
Chain, 8"
Guide bar, 10"
Part Number Description
097572-03S
091375-02S
075752
Guide bar, 16"
Chain, 16"
097567-01S
091371S
075752
Guidebar, 10"
Chain, 10"
Drive Sprocket
091371S
Chain, 10"
Drive sprocket
097568-02S
091373-02S
075752
Guide bar, 12"
Chain, 12"
Drive sprocket
POLE SAW, 104316-04 (8")
POLE SAW ASSEMBLY, 104317
Part Number Description
General
Part Number Description
079963-02
079963-04
Plasticscabbard,8"&10"
099178H, 100089-06, 100089-07,
100089-08, & EL-1
Part Number Description
097570-01S
091374-02S
075752
104302-01S
104301S
075752
Guidebar, 8"
Chain, 8"
Drive Sprocket
Plastic scabbard,
12", 14", & 16"
Hand Guard
106809-01
077155
Guide bar, 14"
Chain, 14"
Drive sprocket
Adjusting Plate Assy.
#
Must order both pieces.
107990
23
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY SERVICE
NON-WARRANTY SERVICE
REPAIR SERVICE
Note: Only use original replacement parts.
Thiswillprotectyourwarrantycoveragefor
parts replaced under warranty.
If saw requires warranty service, return it to If saw requires service, return it to nearest
nearest authorized service center. You must authorized service center. Repairs will be
show proof of purchase. If faulty materials billed to you at regular repair list prices.
or workmanship caused damage, we will Note:Normalwear, misuse, abuse, neglect,
Each authorized service center is indepen-
dently owned and operated. For additional
service center or warranty information, call
1-800-858-8501
repair or replace saw without charge.
or accidental damage is not covered under
warranty.
Model ______________
Serial No. ______________
Date Purchased ______________
ELECTRIC CHAIN SAW LIMITED WARRANTY
Always specify model and serial numbers when writing the factory.
We reserve the right to amend these specifications at any time without notice. The only warranty applicable is our standard written warranty. We
make no other warranty, expressed or implied.
DESA International warrants this electric chain saw and any parts thereof, to be free from defects in material and workmanship for one year (90
days for reconditioned unit) from the date of first purchase from an authorized dealer, provided that the product has been properly maintained
and operated in accordance with all applicable instructions. The bill of sales or proof of purchase must be presented at the time a claim is made
under this warranty.
This warranty is extended only to the original retail purchaser. This warranty covers only the parts and labor required to restore this chain saw
to its proper operating condition. Warranty parts must be obtained through factory authorized dealers and service centers for this product. These
dealers and service centers will provide original factory replacement parts. Failure to use original factory replacement parts voids this warranty.
This warranty does not cover commercial, industrial, or rental usage, nor does it apply to parts that are not in original condition because of normal
wear and tear, or parts that fail or become damaged as a result of misuse, accident, lack of proper maintenance, tampering, or alteration. Travel,
handling, transportation, and incidental costs associated with warranty repairs are not reimbursable under this warranty and are the responsibility
of the owner.
To the full extent allowed by the law of the jurisdiction that governs the sale of the product, this express warranty excludes any and all other
expressed warranties and limits the duration of any and all implied warranties, including warranties of merchantability and fitness for a particular
purpose to one year form the date of first purchase, and DESA International’s liability is hereby limited to the purchase price of the product and
DESA International shall not be liable for any other damages whatsoever including indirect, incidental, or consequential damages.
Some states do not allow limitation of how long an implied warranty lasts or an exclusion or limitation of incidental or consequential damages,
so the above limitation of damages may not apply to you.
Thiswarrantyprovidestheoriginalpurchaserwithspecificrights. Forinformationregardingthoserights, pleaseconsulttheapplicablestatelaws.
TM
P.O. Box 90004
Bowling Green, KY 42102-9004
107990 01
107990-01
Rev. D
05/02
NOT A UPC
Download from Www.Somanuals.com. All Manuals Search And Download.
|