AMX Video Game Controller NI 700 User Manual

Quick Start Guide  
NI-700 NetLinx Integrated Controller  
For more detailed installation, configuration, programming, file transfer, and  
operating instructions, refer to the NetLinx Integrated Controllers Instruction  
Manual, available on-line at www.amx.com.  
NI-700 Specifications (Cont.)  
Rear Panel:  
RS-232/422/485 (Ports 1 & 2): Two RS-232/422/485 control ports  
using DB9 (male) connectors with XON/XOFF (transmit on/transmit  
off), CTS/RTS (clear to send/ready to send), and 300-115,200 baud.  
IR RX (Port 5): This single port is used to connect one or more  
(8 maximum) IRX-SM+ swivel mount or IRX-DM+ Decora mount IR  
receivers.  
The IR RX port functions using AMX IR codes (38 KHz and 455 KHz)  
and works ONLY with AMX IR Receivers such as the IRX-DM+ and  
IRX-SM+.  
Digital I/O (Port 4): Four-channel binary I/O port for contact closure  
with each input being capable of voltage sensing. Input format is  
software selectable with interactive power sensing for IR ports.  
IR/Serial (Port 3): This single port is capable of generating IR with the  
use of an IR emitter (while in IR mode). This port can support  
high-frequency carriers of up to 1.142 MHz and can also generate IR  
with no carrier frequency.  
(front)  
(rear)  
AXlink LED: One green LED indicates the state of the AXlink port.  
AXlink port: 4-pin 3.5 mm mini-Phoenix (male) connector provides data  
and power to external control devices.  
Ethernet port: LEDs show communication activity, connections,  
speeds, and mode information:  
L/A-link/activity - Green LED lights On when the Ethernet cables are  
connected and terminated correctly and blinks when receiving  
Ethernet data packets.  
FIG. 1 NI-700 NetLinx Integrated Controller (front and rear views)  
SPD-speed - Yellow LED lights On when the connection speed is  
100 Mbps and turns Off when the speed is 10 Mbps.  
Power port: 2-pin 3.5 mm mini-Phoenix (male) connector  
Overview  
Included  
Accessories:  
NI-700 Quick Start Guide (93-2105-03)  
The NI-700 unit (FG2105-03) is geared to meet the specific control and  
automation needs of a single room environment, where both price and  
functionality are the driving requirement. This product is configured to control a  
limited number of video players, projectors, lighting, thermostats, and other  
electronic equipment. The NI-700 provides support for 1 IR/Serial Output port,  
2 RS-232/RS-422/RS-485 ports, 4 Digital Input/Output ports, and 1 IR RX port.  
One 6-pin 3.5 mm mini-Phoenix female I/O connector (41-5063)  
One 4-pin 3.5 mm mini-Phoenix female AXlink connector (41-5047)  
One 2-pin 3.5 mm mini-Phoenix female PWR connector (41-5025)  
One CC-NIRC IR Emitter (FG10-000-11)  
OpenSSL Warranty and Licensing Information (93-2105-05)  
Optional  
Accessories:  
2-pin Black Male Phoenix Connector (3.5mm) (41-5026)  
AC-RK Accessory Rack Kit (FG515)  
CC-NIRC IR cables (FG10-000-11)  
CC-NSER IR/Serial cables (FG10-007-10)  
CSB Cable Support Bracket (FG517)  
PSN2.8: Power supply (FG423-17)  
PSN4.4: Power supply(FG423-45)  
PSN6.5: Power supply (FG423-41)  
STS, Serial To Screw Terminal (FG959)  
Surface Mount Bracket Accessory (FG525)  
ATTENTION!  
When working with the NI-700 Integrated Controller, verify you are using the  
latest version of NetLinx Studio v 2.2 build 78 or higher (available for download  
from www.amx.com).  
NI-700 Specifications  
Port Assignment and Functionality  
NetLinx Port Assignments  
Dimensions (HWD):  
1.58" x 5.54" x 5.12" (4.01 cm x 14.10 cm x 13.00 cm)  
1 rack unit high  
Port  
ICSP Port #  
Power:  
280 mA @ 12 VDC  
Serial Port 1  
Serial Port 2  
IR Port  
1
2
3
4
5
Memory:  
32 MB SDRAM  
16 MB Flash chip  
512 Kb of Non-volatile SRAM  
Refer to the NetLinx Integrated Controllers Instruction Manual for more  
information.  
I/O Port  
Microprocessor:  
Weight:  
304 MIPS using a PowerPC™ processor  
1.30 lbs (0.59 kg)  
IR RX Port  
Enclosure:  
Front Panel:  
Metal with black matte finish  
Ethernet Ports used by the NI Controller  
Ethernet Port Usage  
Program Port: RS-232 DB9 connector (male) can be connected to a  
DB9 port on a PC. This port can be used with both Serial and NetLinx  
commands.  
Configuration DIP Switch: Use this DIP switch to set the communication  
parameters for the Program port.  
IR RX LED: Red LED lights to indicate when IR data is being received  
via the rear IR RX port.  
IR LED: Red LED lights to indicate transmission of IR or Serial data  
via the rear IR port.  
I/O LEDs: Four yellow LEDs light when the rear I/O channels 1-4 are  
active. LED indicator for each I/O port reflects the state of that  
particular port.  
Serial LEDs: Two sets of red and yellow LEDs light to indicate the rear  
DB9 Ports 1 & 2 are transmitting or receiving RS-232, 422, or 485  
data. These LEDs do not reflect changes in either the RTS or CTS  
when hardware handshaking is used.  
LINK/ACT: Green LED lights when the Ethernet cable is connected and  
an active link is established. This LED also blinks when receiving  
Ethernet data packets.  
Status: Green LED lights to indicate that the system is programmed  
and communicating properly.  
Output: Red LED lights when the Controller transmits data, sets  
channels On and Off, sends data strings, etc.  
Port type  
Description  
Standard Port #  
ICSP  
Peer-to-peer protocol used for both Master-to-Master and  
Master-to-device communications.  
1319 (UDP/TCP)  
Telnet  
HTTP  
The NetLinx Telnet server provides a mechanism to  
configure and diagnose a NetLinx system.  
23 (TCP)  
The Master has a built-in web server that complies with the 80 (TCP)  
HTTP 1.0 specification and supports all of the required  
features of HTTP v1.1.  
HTTPS  
FTP  
The Master has a built-in SSL protected web server.  
443 (TCP)  
The on-board Master has a built-in FTP server that  
conforms to RFC959.  
21/20 (TCP)  
Internet Inside The Internet Inside feature the Master uses, by default, is  
port 10500 for the XML based communication protocol.  
This port is connected to by the client web browser’s JVM  
when Internet Inside control pages are retrieved from the  
on-board Master’s web server.  
10500 (TCP)  
Input: Yellow LED lights when the Controller receives data from button  
pushes, strings, commands, channel levels, etc.  
ID Pushbutton: Sets the NetLinx ID (Device only) assignment for the  
device.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

3D Innovations Gas Grill 7316 000 User Manual
Acumen Automobile Parts SP500 User Manual
Adaptec Computer Hardware 2268300R User Manual
ADC Network Card 500L User Manual
Aiphone Musical Table NE NVP C User Manual
Avocent Switch xx15 Series User Manual
Axis Communications Security Camera P1357E User Manual
Axis Communications Security Camera Q1615 E User Manual
Barco Camera Lens R9841230 User Manual
Beko Microwave Oven BKMF 4B User Manual