50.7cs,60.7cs,65.7cs,680.7cs
t
kappa series
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
FLUSH-MOUNT
TWEETER ANGLE
Figure 7A. Behind grille panel.
INTERMOUNT III MOUNTING RINGS
The Kappa 60.7cs is packaged with two different
speaker adaptor rings. The rings will allow the
speakers to be installed into various factory 6,"
6-1/2" and 6-3/4" openings. The metal ring can be
mounted in many European vehicles, Japanese
vehicles or vehicles with 6" speaker locations. The
plastic ring can be mounted in many vehicles
using 6-3/4" speaker locations or three-point
mounting frames.
Figure 5A. Mounting the tweeter using the
I-Mount™ flush-mounting kit.
Figure 6. Aim the tweeter at the listening position
by sliding the stud in the groove on the back of
the tweeter cup and rotating the entire assembly
in the mounting surface. Lock the tweeter in
place, using the small retaining screw.
3
3
ROTATE ENTIRE ASSEMBLY
TO AIM ANGLED TWEETER
TOWARD LISTENER.
1
1
2
SLIDE SCREW UP OR
DOWN TO ADJUST
TWEETER ANGLE.
Figure 7B. Mounted to surface behind grille panel.
Figure 3. Mounting the 65.7cs in a 165mm
speaker location using the supplied metal ring.
SURFACE-MOUNT
Figure 5B. Mounting the tweeter using the
I-Mount surface-mounting cup.
2
TIGHTEN SCREW TO
LOCK ANGLE SETTINGS.
4
SECURELY TIGHTEN
1
BLACK (—)
THE LARGE HAND NUT.
ATTACH BASE
WITH SCREWS,THEN:
Figure 7C. Mounted to grille panel.
Figures 7A through 7D. The Starfish™ tweeter
mount is intended to be used when the tweeter
will be installed behind a factory grille (e.g.,
replacing the factory tweeter behind a door
panel). The Starfish will allow you to mount the
component tweeter directly to the panel itself or
to the area behind the panel. The six mounting
tabs can be removed easily to create a number
of custom configurations.
RED (+)
2
3
FOAM GASKET
MOUNTING RING
Figure 4. Mounting the 60.7cs woofer in a standard
speaker location.
Note: Check screw clearance before installing.
Use glue if clearance is an issue.
Figure 7D. In-dash location (may require gluing).
Note: Not all possible mounting configurations
are shown.
FOAM GASKET
kappa series
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
SPECIFICATIONS
50.7cs
Type:
Crossover Frequency:
Woofer
Speaker Impedance:
Power Handling:
Sensitivity:
65.7cs
Type:
Crossover Frequency:
Woofer
Speaker Impedance:
Power Handling:
Sensitivity:
MOUNTING THE CROSSOVER
TWEETER LEVEL ADJUSTMENT
5-1⁄4" 2-Way Component
3.5kHz
165mm 2-Way Component
3.5kHz
Open the crossover housing by placing your
fingers between the terminals and the top cover,
and gently pulling off the cover. Using screws or
a wire tie, mount the crossover through the holes
provided.
Located on the right side of the crossover network
is a small switch which controls the tweeter level.
The upper position is +3dB and the lower position
is 0dB. Adjust to personal preference.
2 ohms
85W RMS, 255W Peak
94dB @ 2.83V, 1m
2 ohms
90W RMS, 270W Peak
95dB @ 2.83V, 1m
Frequency Response: 55Hz – 25kHz
Frequency Response: 45Hz – 25kHz
CONNECTIONS
Mounting Depth:
Cutout Diameter:
Tweeter
Speaker Impedance:
Power Handling:
Sensitivity:
2-1/16" (53mm)
4-11/16" (120mm)
Mounting Depth:
Cutout Diameter:
Tweeter
Speaker Impedance:
Power Handling:
Sensitivity:
2-1/4" (58mm)
5-5/8" (143mm)
Observing proper polarity, connect the speakers
and amplifier as shown in 8A and 8B. Replace the
cover when you are finished making connections.
2 ohms
50W RMS, 150W Peak
94dB @ 2.83V, 1m
2 ohms
50W RMS, 150W Peak
94dB @ 2.83V, 1m
Figure 8A. Wiring connections on the crossover
network (shown with cover on).
Frequency Response: 3.5kHz – 25kHz
Frequency Response: 3.5kHz – 25kHz
Mounting Depth:
Cutout Diameter:
3/4" (19mm)
1-7/8" (48mm)
Mounting Depth:
Cutout Diameter:
3/4" (19mm)
1-7/8" (48mm)
Declaration of Conformity
60.7cs
Type:
Crossover Frequency:
Woofer
Speaker Impedance:
Power Handling:
Sensitivity:
680.7cs
Type:
We, Harman Consumer Group International
2, route de Tours
72500 Chateau-du-Loir
France
6-1⁄2" 2-Way Component
3.5kHz
6" x 8"/5" x 7"
2-Way Component
3.5kHz
Crossover Frequency:
Woofer
Speaker Impedance:
Power Handling:
Sensitivity:
2 ohms
90W RMS, 270W Peak
95dB @ 2.83V, 1m
RED
declare in own responsibility that the products
described in this owner’s manual are in compliance
with technical standards:
2 ohms
90W RMS, 270W Peak
94dB @ 2.83V, 1m
TO AMPLIFIER
TO TWEETER
SPEAKER OUTPUTS
TO WOOFER
BLK
Frequency Response: 45Hz – 25kHz
Mounting Depth:
Cutout Diameter:
Tweeter
Speaker Impedance:
Power Handling:
Sensitivity:
Frequency Response: 3.5kHz – 25kHz
Mounting Depth:
Cutout Diameter:
2-3⁄16" (56mm)
5" (127mm)
Frequency Response: 40Hz – 25kHz
Figure 8B. Locating wiring connections on the
woofer.
EN 61000-6-3:2001
EN 61000-6-1:2001
Mounting Depth:
Cutout Diameter:
2-1/4" (58mm)
7-1/8" x 4-7/8"
(181mm x 124mm)
2 ohms
50W RMS, 150W Peak
94dB @ 2.83V, 1m
Klaus Lebherz
Tweeter
Harman Consumer Group International
Chateau-du-Loir, France 2/05
Speaker Impedance:
Power Handling:
Sensitivity:
2 ohms
50W RMS, 150W Peak
94dB @ 2.83V, 1m
Big Lug =
Small Lug =
3/4" (19mm)
1-7/8" (48mm)
Frequency Response: 3.5kHz – 25kHz
Mounting Depth:
Cutout Diameter:
3/4" (19mm)
1-7/8" (48mm)
Infinity Systems, 250 Crossways Park Drive, Woodbury, NY 11797 USA
© 2005 Harman International Industries, Incorporated • Part No. KAPCSOM2/05
A valid serial number is required for warranty coverage.
Features, specifications and appearance are subject to change without notice.
Intermount III patent no. 6,505,705.
Download from Www.Somanuals.com. All Manuals Search And Download.
|