Philips HOSPITALITY 26HF5335D User Manual

Hospitality Television  
20/26/32HF5335D  
15/20HF5234  
- 1 -  
Installing Analogue Programs  
Ensure the TV is in Analogue mode. If it is in Digital mode, press the A/D (Analogue/Digital) key on the  
Remote Control to enter the Analogue mode.  
1. Press the  
(Menu TV) key on the Remote Control  
2. Press the Up/Down Arrow Key to scroll to the item called INSTALL and press OK  
3. Press the Up/Down Arrow Key to scroll to the item AUTO STORE and press OK  
The TV will now start to scan and install all available (Analogue) TV channels automatically. This operation will  
take a few minutes. The TV display will show the progress of the scan and the number of programmes found.  
Refer to the chapter on Automatic Tuning of Analogue Programmes in the User Manual for more details. You  
can also refer to the chapter on Manual Tuning of Analogue Programmes in the User Manual if a manual scan is  
preferred.  
4.  
Activating the Hotel Mode Setup menu (BDS)  
1. Switch on the television and select an analogue channel  
2. On the Remote Control, press keys: [3, 1, 9, 7, 5, 3, MUTE]  
3. The BDS HOTEL MODE SETUP MENU becomes visible  
4. Use the cursor keys to select and change any of the following settings:  
Function  
Possible selections  
BDS MODE  
ON /OFF  
SWITCH ON SETTINGS  
SWITCH ON VOLUME  
MAXIMUM VOLUME  
SWITCH ON CHANNEL  
POWER ON  
DISPLAY MESSAGE  
WELCOME MESSAGE  
CONTROL SETTINGS  
LOCAL KEYBOARD LOCK  
REMOTE CONTROL LOCK  
OSD DISPLAY  
HIGH SECURITY MODE  
AUTO SCART  
MONITOR OUT  
BLANK CHANNEL  
STORE  
0-100, LAST STATUS  
0-100  
USER DEFINED, LAST STATUS  
ON/STANDBY/LAST STATUS  
ON/OFF  
LINE 1/LINE 2/CLEAR  
ON/OFF/ALL  
ON/OFF  
ON/OFF  
ON/OFF  
ON/OFF  
ON/OFF  
ON/OFF  
>
5. Select STORE” and press [CURSOR RIGHT] to save the settings and exit BDS Hotel Mode  
setup. Press [MENU] to exit without saving.  
6. For BDS Hotel Mode settings to take effect, you must turn the TV set Off, then back On.  
BDS Hotel Mode Functions  
This paragraph describes the functionality of each item in the BDS Hotel Mode Setup menu.  
BDS MODE  
ON  
BDS Hotel Mode is ON:  
The user menu is blocked.  
All settings of the Hotel Mode Setup menu are in effect.  
- 3 -  
OFF  
BDS Hotel Mode is OFF:  
The TV operates as a normal consumer TV  
SWITCH ON VOL  
When the user switches the TV ON, it will play at the specified volume level. There are 2 options:  
LAST STATUS Upon start-up, the TV volume will be set to the level before the TV set was  
last turned off.  
USER DEFINED As specified by installer  
Remark: “SWITCH ON VOL” cannot exceed the MAXIMUM VOL level. This is the volume level with which  
the Hotel Mode Setup menu was entered.  
MAXIMUM VOL  
The TV Volume will not exceed the selected volume level.  
SWITCH ON CHANNEL  
When the user switches the TV ON, it will tune to the specified channel. There are 2 options:  
LAST STATUS The TV will switch on to the last channel that was shown before the TV set  
was turned off  
USER DEFINED Any analogue channel can be chosen to be the first channel to switch on  
POWER ON  
The Power On function allows the TV to enter a specific mode of operation (On or Standby) after the mains  
power is activated.  
ON  
STANDBY  
When set, the TV will always turn ON after the mains power is enabled.  
When set, the TV will always turn to STANDBY after mains power is enabled  
LAST STATUS When set, the TV will always turn to the last power status before the mains power was  
disabled.  
DISPLAY MESSAGE  
ON  
OFF  
Enables display of the Welcome Message for 30 seconds after the TV set is turned on  
Disables the display of the Welcome Message.  
If OSD DISPLAY is set to OFF, then the Welcome Message is automatically disabled.  
WELCOME MESSAGE  
The Welcome Message function allows the TV to show a customized greeting to the hotel guest whenever the  
TV is switched on. This helps to personalize the hotel experience for guests.  
The Welcome Message can consist of 2 lines of text, with each line containing a maximum of 20 alphanumeric  
characters. Use the Remote Control arrow keys to create the Welcome Message.  
To enable the display of the Welcome Message, the DISPLAY MESSAGE option must be ON  
To clear the Welcome Message from the TV’s memory, select CLEAR  
LOCAL KEYBOARD LOCK  
ON  
OFF  
ALL  
The television keys VOLUME +/-, PROGRAM +/- and MENU are blocked.  
The television keys VOLUME +/-, PROGRAM +/- and MENU function normally  
The television keys VOLUME +/-, PROGRAM +/-, MENU and POWER are blocked.  
REMOTE CONTROL LOCK  
ON  
OFF  
Standard Remote Control keys are disabled.  
All Remote Control keys will function normally.  
OSD DISPLAY  
ON  
OFF  
Normal screen information is displayed (e.g. programme information)  
Screen information is suppressed.  
- 4 -  
HIGH SECURITY MODE  
ON  
Allows access to the BDS Hotel Mode Setup Menu via the special BDS Setup Remote only.  
(RC2573/01)  
OFF  
Allows access to the BDS Hotel Mode Setup Menu via BDS Setup Remote or via normal Remote  
Control (using special key code sequence).  
AUTO SCART  
The Auto Scart function enables auto-detection of AV devices that are connected to the TV’s Scart connector.  
ON  
OFF  
Enables Auto Scart switching in BDS Hotel Mode.  
Disables Auto Scart switching in BDS Hotel Mode.  
MONITOR OUT  
ON  
OFF  
Allows audio & video output from TV via relevant AV connectors (if available).  
Disables both Audio & Video output from the TV (to prevent illegal copying).  
BLANK CHANNEL  
The Blank Channel function disables the display of video on the TV, but does not affect the audio output. This  
function can be used for audio applications (example: Off-air radio transmission, music channels, and so on),  
which do not necessarily require the display of video.  
ON  
The current programme is blanked  
OFF The current programme is not blanked (normal visible; DEFAULT value)  
BLANK CHANNEL can be set for every channel. Use [P+ / P-] to go through all the programmes and set the  
desired status per channel. The programme number is visible in the top left corner.  
Low Battery Check  
This television set has a special feature which checks the battery power level of a TV Remote Control, and  
indicates if the battery is low and requires changing.  
(Note: The Low Battery Check function works only with certain models of Remote Controls. Please check  
with the Philips sales representative if the Remote Control used with this TV supports this function)  
To activate the Low Battery Check function, hold the TV Remote Control in front of the TV, and press and  
hold the OK button on the Remote Control for at least 5 seconds. A message will appear on the TV screen to  
indicate if the battery power level is OK, or if it is Low. If the message indicates that the battery level is low, it  
is recommended to change the batteries of the Remote Control immediately.  
5.  
Cloning of settings  
Cloning of analogue TV channels and TV settings as described in the chapter  
Hotel Mode Set-up menu  
For 15/20HF5234  
o
o
Wireless cloning with the SmartLoader 22AV1120 or 22AV1135  
Cloning off all adjustable TV settings + analogue channel table  
For 20/26/32HF5335D  
o
o
Wired cloning with the SmartLoader 22AV1135 using the wire packed with the SmartLoader  
Cloning off all adjustable TV settings + analogue channel table (digital channel table via automatic  
installation)  
Instruction for cloning of settings between TVs  
Philips SmartLoader (22AV1135/00)  
The Philips SmartLoader is an installation tool especially designed for easy and fast installation and copying of  
TV settings on Philips Institutional TV’s.  
- 5 -  
The Philips SmartLoader works in 2 modes – Wireless and Wired:  
Wireless mode ---- through infrared sensor (15/20HF5234)  
Switch the SmartLoader to “Wireless” mode by sliding the side-switch to the  
icon on the SmartLoader  
device. Point the Wireless SmartLoader to the TV’s infrared receiver (optimal distance of 5-30cm) and proceed  
with the Installation procedure listed below.  
Wired mode ---- using the by-packed accessory cable(s) (20/26/32HF5335D)  
Switch the SmartLoader to “Wired” mode by sliding the side-switch to the  
device.  
icon on the SmartLoader  
Examine the rear connectors of the TV set to determine if the 3-pin or 4-pin female connector wire (packed  
with the Wireless SmartLoader) should be used. Plug in the correct connector wire to the corresponding  
opening on the TV set (usually marked as SERV C), and then connect the RJ11 jack end of the accessory wire  
to the RJ11 socket on the SmartLoader.  
The Installation Procedure consists of three simple steps:  
1. Choosing a Master TV  
The Master TV is the TV set whose installation and configuration settings are to be copied into other TV’s (of  
the same type only).  
2. Programming the SmartLoader with the settings from the Master TV  
Follow these steps to program the SmartLoader with the settings of the Master TV.  
a) Wireless method  
Set the SmartLoader to “Wireless” mode using the side switch.  
Turn on the TV, and while holding the SmartLoader, point it in the direction of the  
TV. Press the “MENU” Key on the SmartLoader.  
b) Wired method  
Connect the SmartLoader to the TV using the appropriate accessory cable.  
Set the SmartLoader to “Wired” mode using the side switch.  
Turn on the TV, and while holding the SmartLoader, point it in the direction of the  
TV. Press the “MENU” Key on the SmartLoader.  
The Master TV will show the following menu:  
SMARTLOADER TO TV >  
TV TO SMARTLOADER >  
On the TV screen, highlight the menu option “TV TO SMARTLOADER”  
Press the right arrow key on the SmartLoader to start the programming process  
A number display (from 0~100) will be shown on screen, indicating the percentage of the programming  
progress from the TV to the SmartLoader. When the programming is completed, “##” will show “100” and the  
message “DONE” will appear.  
TV TO SMARTLOADER ## (0-100)  
The SmartLoader is programmed and can be used to install and configure other TVs.  
Copying the settings of the Master TV to other TVs with the SmartLoader  
Follow these steps to install and configure the settings of a Philips TV with the SmartLoader.  
- 6 -  
a) Wireless method  
Set the SmartLoader to “Wireless” mode using the side switch.  
Turn on the TV, and while holding the SmartLoader, point it in the direction of the  
TV. Press the “MENU” Key on the SmartLoader.  
b) Wired method  
Connect the SmartLoader to the TV using the appropriate accessory cable.  
Set the SmartLoader to “Wired” mode using the side switch.  
Turn on the TV, and while holding the SmartLoader, point it in the direction of the  
TV. Press the “MENU” Key on the SmartLoader.  
On the TV screen, highlight the menu option “SMARTLOADER TO TV”  
Press the right arrow key on the SmartLoader to initiate the copying process  
> A number display (from 0~100) will be shown on screen, indicating the percentage of the installation  
progress from the SmartLoader to the TV. When the data transfer is completed, “##” will show “100” and  
the message GOODBYE will appear.  
SMARTLOADER TO TV ## (0-100)  
>
The TV will go to Standby mode. When the TV is next powered on, it will be configured with the settings  
from the Master TV, and ready for use.  
Problems and Solutions:  
1. The message “I2C ERROR” is displayed on the screen.  
Bad connection of RJ11 wire or wrong data transmission has occurred. Try again.  
2. The message “WRONG VERSION” is displayed on the screen.  
The program contained in the SmartLoader has a software code incompatible with the actual TV.  
Reprogram the Wireless SmartLoader from a Master TV whose software code is compatible with the  
actual TV.  
3. TV doesn’t respond to the SmartLoader.  
Check if the LED on the SmartLoader lights up in green when pressing any button.  
If the LED is red, it means that the batteries are low and should be replaced.  
Bring the SmartLoader closer to the TV infrared receiver and try again.  
Notes:  
Make sure that the 3 R6/AA sized batteries are placed correctly in the bottom compartment of the  
SmartLoader. The LED on the SmartLoader should light up in green when pressing any button, indicating  
operational batteries. When the LED shows red, the batteries need to be replaced.  
The SmartLoader can only copy the settings between 2 TVs of the same type. Once the  
SmartLoader is programmed with the settings from a Master TV of a certain type or model,  
then these settings can be installed on another TV of the same model only.  
The SmartLoader cannot be used to copy the (digital) channel table of a Digital TV set.  
If the SmartLoader is used with a DVB (European Digital) TV set, then the TV set must first  
be switched to Analog mode.  
- 7 -  
Disposal of your old product.  
Your product is designed and manufactured with high quality materials and  
components, which can be recycled and reused. When this crossed-out wheeled bin  
symbol is attached to a product it means the product is covered by the European  
Directive 22002/96/EC. Please find out more about the separate collection system for  
electrical and electronic products in your local neighborhood.  
Please act according to your local rules and do not dispose of your old products with  
your normal household waste. The correct disposal of your old product will help  
prevent potential negative consequences for the environment and human health.  
The packaging of this product is intended to be recycled. Apply to the  
local authorities for correct disposal.  
2007© Koninklijke Philips Electronics N.V. all rights reserved  
Specifications are subject to change without notice  
Trademarks are property of Koninklijke Philips Electronics N.V. or their respective owners.  
- 8 -  
CZ UŽIVATELSKÁ PŘÍRUČKA