The remote control
REC/OTR n
Record: Record the current TV channel
STANDBY m
Switch on or off: To switch set on or off, interrupt menu function,
interrupt a programmed recording (TIMER)
TIMER s
TIMER: To make a TIMER programming with/without Video Plus+® or
to alter or clear a programmed TIMER
REC MODE
PLAY MODE
TV/DVD
Record type (quality): To select the maximum possible record time
Playback type: Choose between repeat, shuffle play and intro-scan
TV/DVD switch: Switches the scart socket EXT 2 AUX-I/O of the
DVD recorder directly to the TV set. This lets you watch the picture
from any unit connected to this scart socket (set-top box', video
recorder or satellite receiver) and at the same time record from
another source.
If you have not connected a device to the EXT 2 AUX-I/O socket or
the device is switched off, you can use this button to switch between
TV reception and the signal of the DVD recorder.
But this only works if you use a scart cable to connect the TV set to
your DVD recorder ( EXT 1 TO TV-I/O socket) and your TV set
responds to this switch-over.
MONITOR
DIM
Monitor: This button lets you switch between disc playback or the
picture of the internal tuner (TV channel).
Dimmer: This button lets you change the brightness of the display to
one of two levels or switch it off.
RETURN
T/C
Back: Return to previous menu on a video CD (VCD). This also works
with some DVDs.
Title/Chapter: Choose the ' '(Title)/' '(Chapter) directly from the
B
C
menu bar using P- B , P+ A .
If 'INFO' appears in the display, the index menu from a recorded disc or
an introductory film will be shown. In this case, this function is not
available.
DISC MANAGER
Disc Manager: Call up or cancel the Disc Manager
FSS &
EDIT: For displaying the edit menu for DVD+R/RW discs, for setting
chapter markers
SELECT
t
Select: Select function/value
Info: Call up additional information in the GUIDE Plus+® system.
ZOOM
Zoom: Enlarge the picture
In the GUIDE Plus+® system: Red function button.
ANGLE
Angle: Select the camera angle.
In the GUIDE Plus+® system: Green function button.
SUBTITLE
Subtitle : Select the subtitle language.
In the GUIDE Plus+® system: Yellow function button.
AUDIO
Audio: Selecting the audio language. For recording or during playback
using the internal tuner ( MONITOR key), select language 1 or 2.
In the GUIDE Plus+® system: Blue function button.
DISC-MENU
GUIDE/TV
Disc menu: To show the DVD menu or the index screen
The GUIDE Plus+® System: Call up/Cancel the GUIDE Plus+®
System
D C
Cursor keys : Cursor left, right
P+ A
Cursor buttons/Plus : Cursor up/ Next programme number
Cursor buttons/Minus : Cursor down / Previous programme number
Store/confirm: To store or confirm entry
P- B
OK
SYSTEM-MENU
System menu: Call up/cancel the main menu (menu bar at the top of
the screen)
STOP h
Stop: Stop playback/recording, except with programmed recordings
(TIMER)
Hold down button, opens and closes the disc tray.
PLAY G
Playback: To play a recorded disc.
N
Select previous title/search backwards :
Briefly press the button during playback: Previous chapter/film or
previous title
Hold down the button: Search backwards
Hold down button during still picture, slow motion backwards
SLOW Z
Slow motion: Playback with 1/2, 1/4, 1/8 of the normal playback speed.
PAUSE 9
Pause (still picture):
If this button is pressed during playback, the DVD recorder switches to
pause. You will see a still picture.
If this button is pressed during recording, the DVD recorder will also
switch to pause.
O
Select next title/search forwards :
Briefly press the button during playback: Next chapter/film or next title
Hold down the button: Search forwards
Hold down button during still picture, slow motion forwards
0..9
Number buttons: 0 - 9
CLEAR
Delete: Delete the last entry
Additional TV functions
This will only work with TV sets with the same remote control code *RC5) (e.g. Philips TV sets)
TV VOLUME q
TV VOLUME r
MUTE y
TV volume: Increase TV volume
TV volume: Reduce TV volume
TV sound off: Switch TV sound on/off
For the following functions you need to hold down the button at the left side •TV and then
select the function you need with the appropriate button.
STANDBY m
0..9
Switching the TV off
Number buttons: 0 - 9
P+ A
TV programme number: To select a higher programme number
TV programme number: To select a lower programme number
P- B
Front of the device
STANDBY-ON m
Switch on or off: To switch off or on, interrupt a function, interrupt a
programmed recording (TIMER)
OPEN/CLOSE J
Open/close disc tray: Open/close disc tray
TRAY LED
Recording in progress: Red light around the disk tray to indicate
recording in progress
GUIDE
The GUIDE Plus+® System: Call up/Cancel the GUIDE Plus+®
System. When GUIDE Plus+® is active, this button lights up white.
UP , DOWN
Select: Higher/lower programme number
Moves cursor up/down in the GUIDE Plus+® system
LEFT , RIGHT
Select: In the GUIDE Plus+® System: Cursor left/right
RECORD
Record: Record the current TV channel
In the GUIDE Plus+® System: red function button.
G
Playback: To play a recorded disc
In the GUIDE Plus+® System: OK button.
N
O
h
Select previous title/search backwards
Select next title/search forwards
Stop: Interrupt playback/recording
Behind the flap at the right;hand corner on
the front
Switching between the S-VIDEO and VIDEO sockets takes place automatically. If a signal is
available at both sockets at the same time, the signal at the S-VIDEO socket has priority.
S-VIDEO
S;Video socket: Connection of SVHS/Hi8 camcorders or SVHS/Hi8
video recorders (programme number 'CAM1')
Yellow socket
Video input socket: Connection of camcorders or video recorders
VIDEO
(programme number 'CAM1')
White/red socket
Audio input socket left/right : Connection of camcorders or video
left AUDIO right
recorders (programme number 'CAM1')
DV IN
i;Link/DV socket (digital video input, IEEE 1394, FireWire):
Connecting a digital camcorder or other suitable device (programme
number 'CAM2').
Back of the unit
4MAINS
Mains socket: Connection to the mains supply (230V/50Hz)
ANTENNA IN
TV OUT
Aerial input: Connection of the aerial
Aerial output: Connection of the TV set
EXT 2 AUX-I/O
Scart socket 2: Connection of an additional device (satellite receiver,
set-top box, video recorder, camcorder, etc.). RGB input
EXT 1 TO TV-I/O
Scart socket 1: Connection of a TV set. RGB output
Output sockets (AUDIO/VIDEO OUT)
OUT S-VIDEO (Y/C) S;Video output: Connection of an S-Video-compatible TV set
VIDEO (CVBS)
OUT
Video output (yellow socket): Connecting a TV set with a video
input (CVBS, Composite Video)
OUT AUDIO L/R
Analogue audio output (white/red socket): Connection of a TV
set with audio input sockets or connection of an additional device
COMPONENT
VIDEO OUT
Component Video output (red/blue/green socket): Connection
of an additional device with Component Video input
Output sockets (DIGITAL AUDIO OUT)
COAX OUT
Coaxial digital audio output
OPTICAL AUDIO
OUT
Optical digital audio output
Output socket (G;LINK)
G-LINK
Connection of the supplied remote control (IR transmitter) for an
external receiver (satellite receiver, set-top box, cable TV box).
The symbols on your DVD recorder
display
These symbols can light up on your DVD recorder display:
Multi-function display/text line
•) Clock
•) Disc/title playing time
•) OTR switch-off time
•) Title name
•) Display of the programme number of the TV channel/playing
time/channel name/function.
•) Display of information and alerts
IIIIIIIIIIIIIII
SAT
Disc bar: Displays the current position on the disc (disc pointer).
Play/Record: Single flashing segment at the current position.
Pause: Flashing segment on both sides of the current position.
Stop: Illuminated segment at the current position.
An automatic recording from a satellite receiver (SAT recording) has
been programmed.
TIMER
o(((
A recording (timer) has been programmed
A remote control signal has been received
VPS/PDC
Video programming system / programme delivery control: A VPS or
PDC code will be transmitted for the selected TV program
LANG II
During playback a 2-channel tone was detected or a 2-channel tone was
received. 'I' or 'II' lights up depending on which sound channel has been
selected (button AUDIO )
Messages in the DVD recorder display
The following messages may appear in your DVD recorder display
READING
IS TV ON?
The DVD recorder is in initial installation mode. Switch the TV on, then
read the paragraph on 'Initial installation' in 'Installing your DVD
recorder'.
NO SIGNAL
MENU
No input signal available (signal inadequate or unstable)
The menu on the screen is active
Disc tray opening
OPENING
TRAY OPEN
CLOSING
READING
MENU UPDT
Disc tray open
Disc tray closing
Disc being read
Once recording has been successfully completed the table of contents is
created.
INIT MENU
COPY PROT
The menu structure is created after the first recording has been made
on a new disc
You received a copy-protected signal. This may come from a
copy-protected DVD/videotape of a DVD/video player or from a TV
channel.
WAIT
Please wait until this message disappears. The DVD recorder is busy
performing a task.
NO DISC
A disc has not been inserted for recording. If a disc has been inserted, it
cannot be read.
INFO
BUSY
Information about the inserted DVD is displayed on the screen
The DVD recorder is processing the changes to make them DVD
compatible
ERASING
The entire disc is erased
EMPTYDISC
The disc inserted is either new or has been completely erased (no
recordings).
PROTECTED
MAX TITLE
The disc is protected against recording.
The maximum number of titles per disc has been reached. The
maximum number of titles on a disc is 48.
MAX CHAP
The maximum number of chapters within a title/or the disc has been
reached. The maximum number of chapters within a title is 99, on a disc
124.
DISC FULL
The disc is full. There is no space for new recordings
PAL DISC
NTSC DISC
RECORDING
A disc with PAL recordings has been inserted. The machine is trying to
record an NTSC signal. Insert a new disc or one that contains NTSC
recordings.
A disc with NTSC recordings has been inserted. The machine is trying
to record a PAL signal. Insert a new disc or one that contains PAL
recordings.
An illegal action (e.g. OPEN/CLOSE J button) was attempted during
recording.
FREETITLE
DISC LOCK
Playback was started for an empty title or the following title is empty.
An attempt has been made to record during playback of a protected
disc. This message appears if an attempt is made to insert a chapter
marker ( FSS & button).
DISC ERR
An error occurred when writing the title. If this error keeps occurring,
please clean the disc or use a new one.
For instructions on how to clean a disc see the section on 'Cleaning the
discs' in the next chapter.
DISC WARN
An error occurred when writing the title. Recording was continued; the
error was skipped
SETUP
The automatic search is completed.
WAIT 01
During the automatic channel search the TV channels found will be
counted.
BLOCKED
The disc tray cannot be closed/opened.
SAFE REC
The new recording will be added at the end of all the other recordings
(SAFE RECORD).
EASYLINK
POST-FORMAT
PHILIPS
STANDBY
GUIDE
Data transfer 'EasyLink' from the TV is in progress
After the creation of the menu structure the disc is prepared
The DVD-Recorder has been switched on
The DVD-Recorder has been switched off
The GUIDE Plus+® system is switched on
Table of contents
The 'Search' screen ........................................................................................ 47
The 'Schedule' screen .................................................................................... 48
The 'Info' screen ............................................................................................. 49
The 'Editor' screen ......................................................................................... 49
The 'Setup' screen .......................................................................................... 50
A
Introduction .................................... 3
Dear Philips customer, .................................................................................... 3
Regional code .................................................................................................... 6
Technical data ................................................................................................... 6
Accessories ........................................................................................................ 6
Important ........................................................................................................... 7
Cleaning the discs ............................................................................................. 8
Special functions of your DVD recorder .................................................... 8
F
On;screen information ................ 51
Symbols in the menu bar .............................................................................. 51
Menu bar 1 ....................................................................................................... 51
Menu bar 2 ....................................................................................................... 51
Field for temporary messages ..................................................................... 52
Status field ........................................................................................................ 52
Disc type symbols .......................................................................................... 52
Operating mode symbols ............................................................................. 53
Tuner information box ................................................................................. 53
Timer information box ................................................................................. 53
B
Connecting the DVD recorder ... 11
Important information for customers in Great Britain ......................... 11
Preparing the remote control for operation ........................................... 11
Connecting your DVD recorder to the TV set ...................................... 12
Connecting with a scart cable and 'Easy Link' .......................................... 13
Connecting with a scart cable without 'Easy Link' .................................. 15
Connecting with an S-Video(Y/C)cable ..................................................... 16
Connecting with video(CVBS) cable .......................................................... 17
G
Playback ........................................ 54
General notes on playback ........................................................................... 54
Inserting a disc ................................................................................................ 54
Playing a DVD video disc .............................................................................. 55
Playing a DVD+RW/ +R disc ....................................................................... 56
Playing an audio CD ....................................................................................... 56
Playing an MP3 CD ......................................................................................... 57
Playing a (Super) Video CD ......................................................................... 58
C
Connecting additional devices .... 19
Connecting additional devices to the second scart socket ................... 19
Connecting a video recorder, DVD player. ............................................. 19
Connecting an external receiver (satellite receiver, set-top box,
cable TV box,...) .............................................................................................. 19
Connecting additional devices only via aerial cable ................................ 20
Connect camcorder to the front sockets ................................................ 21
Connecting audio devices to the analogue audio sockets .................... 21
Connecting audio devices to the digital audio sockets .......................... 22
H
Additonal playback features ........ 59
Changing to another title/chapter .............................................................. 59
Searching a disc ............................................................................................... 59
Still picture ....................................................................................................... 60
Slow motion .................................................................................................... 60
Search by time ................................................................................................. 60
Repeat/Shuffle play ......................................................................................... 61
Repeating a passage (A-B) ............................................................................ 61
Scan feature ..................................................................................................... 62
Camera angle ................................................................................................... 62
Zoom feature .................................................................................................. 62
Select the audio language .............................................................................. 63
Subtitles ............................................................................................................ 63
D
Installing your DVD recorder...... 23
Initial installation ............................................................................................. 23
Using a satellite receiver ............................................................................... 25
Allocating a decoder ...................................................................................... 26
Connection using a component video (Y Pb Pr/YUV) cable ................ 27
Manual TV channel search ............................................................................ 28
Sorting TV channels automatically (Follow TV) ...................................... 30
Automatic TV channel search (Autoinstall) ............................................. 32
Sorting and deleting TV channels manually .............................................. 33
Setting the language ....................................................................................... 34
'Recording audio' switching over (2-channel sound) .............................. 35
Setting the time and date .............................................................................. 36
I
Disc Manager (DM) ...................... 64
General information ...................................................................................... 64
Adding a disc to the Disc Manager ............................................................. 64
Removing discs from the Disc Manager .................................................... 65
Searching for a title in the Disc Manager .................................................. 66
Searching discs ................................................................................................ 67
Searching for a blank section ....................................................................... 68
®
E
The GUIDE Plus+ System ........... 37
General information ...................................................................................... 37
Setting up the GUIDE Plus+® System ........................................................ 38
'Setup' ................................................................................................................ 38
Installation of the 'External receiver 1' ...................................................... 40
Continue set-up .............................................................................................. 43
Using the GUIDE Plus+ ® System ............................................................... 44
General ............................................................................................................. 44
The 'Grid' screen ............................................................................................ 45
Table of contents
J
Manual recording.......................... 69
NAccess control (Child Lock) ...... 100
General ............................................................................................................. 69
Recording without automatic switch-off ................................................... 70
Interrupt recording (Pause) ......................................................................... 71
Recording with automatic switch-off (OTR one-touch-recording) .... 72
Preventing accidental erasing of discs ........................................................ 72
Lining up recordings within a title (assemble cut) .................................. 73
Selecting the recording type (Quality)....................................................... 74
Automatic recording from a satellite receiver (Sat recording) ............ 75
Direct Record ................................................................................................. 76
Switching 'Direct Record' on or off ........................................................... 77
Child lock (DVD and VCD) ....................................................................... 100
Activating/deactivating child lock .............................................................. 100
Authorising a disc ......................................................................................... 101
Locking unlocked discs ................................................................................ 101
Parental level control (DVD video only) ................................................ 101
Activating/deactivating parental level control ........................................ 101
Changing the country .................................................................................. 102
Changing the PIN code ............................................................................... 103
O
Before you call an engineer ....... 104
K
Managing the disc contents ......... 78
General ............................................................................................................. 78
Favorite Scene Selection ............................................................................... 79
Insert chapter markers ................................................................................. 79
Hiding chapters ............................................................................................... 79
Deleting chapter markers ............................................................................. 81
Changing the index picture .......................................................................... 81
Dividing titles ................................................................................................... 82
Editing recording titles (name) .................................................................... 82
Playing the entire title ................................................................................... 83
Erasing recordings/titles ................................................................................ 83
Disc settings .................................................................................................... 84
Changing the disc name ................................................................................ 84
Finishing editing ............................................................................................... 85
Finalising DVD+R discs ................................................................................. 85
Erase DVD+RW disks ................................................................................... 86
L
Programming a recording
(TIMER) .............................................. 87
General ............................................................................................................. 87
Programming recordings with the GUIDE Plus+® System .................... 88
Programming recordings with the VIDEO Plus+® System .................... 89
Programming recordings without the VIDEO Plus+® System .............. 91
How to change or delete a programmed recording (TIMER) ............. 93
'NexTView Link' ............................................................................................. 94
Problem solving for programmed recordings .......................................... 94
M
User preferences .......................... 95
Picture settings ................................................................................................ 96
Sound settings ................................................................................................. 97
Language settings ............................................................................................ 97
Additional settings .......................................................................................... 98
Remote Control settings .............................................................................. 99
Disk feature menu .......................................................................................... 99
Table of contents
AIntroduction
Dear Philips customer,
Instruction manuals are usually very dry since they are technically-oriented and often poorly
translated. I have therefore been employed by Philips to help you.
Allow me to introduce myself.
My name is Phil. I will be guiding you through the instruction manual and helping you get to
know your new DVD recorder. At appropriate points along the way, I will be providing you with
the following information:
Question: (?)
Tip
Problem
Here I will be explaining
seemingly unimportant
things.
Here I will be giving you
instructions on functions
that will make it easier for
you to use your DVD
recorder.
Here I'll help you identify
the cause of a problem and
find a solution.
I hope you have lots of fun.
Phil
P.S. If you have any problems operating the machine, please read the section entitled 'Before you
call an engineer'. If this doesn't help you to resolve the problem, please call the customer
support service for your country.
The telephone numbers and e-mail addresses can be found on the last page of this instruction
manual.
You can also visit the website 'http://www.p4c.philips.com' .
3
Introduction
Welcome to the growing familyof owners of PHILIPS equipment.
Thank you for buying a DVDR 80/051 .
Please take the time to read this operating manual before using your DVD recorder. It contains
important information on how to set up and operate the machine.
The DVD recorder should not be turned on immediatelyafter transportation from a
cold to a hot area or vice versa, or in conditions of extreme humidity.
Wait at least three hours after transporting the machine. The DVD recorder needs this time
to acclimatise to its new environment (temperature, relative humidity, etc.).
Your Philips team hopes your
new DVD recorder will bring you
many years of enjoyment.
What is a DVD?
DVD (Digital Versatile Disc) is a new storage medium that combines the
convenience of the compact disc with the latest digital video technology. DVD
video uses modern MPEG2 data compression technology that enables an
entire feature film to be stored on a single five inch disc.
How good is the resolution of DVD compared with VHS?
The razor-sharp digital images have a resolution of more than 500 lines of 720
pixels per line. This is more than twice as high as VHS and is even better than
the laser disc. Its picture quality is easily comparable to the digital masters
produced in recording studios.
What can DVD+RW do?
DVD+ReWritable uses phase change media, the same technology on which
rewritable CDs are based. A high-performance laser is used to change the
reflective properties of the recording layer; this process can be repeated more
than a thousand times.
What can the DVD+R do?
DVD+R (write-once DVD). Unlike a DVD+RW disc, this disc can only be
written to once. If it is not finalized after a recording, further recordings can
be added to it. Old recordings can be deleted but can no longer be
overwritten. The deleted titles are marked 'Deleted title'.
Before this disc can be played in a DVD player, it must be finalised in the
DVD recorder. Once this process is complete, no further recordings can be
added.
What can myDVD recorder do?
Your Philips DVD recorder is a machine for recording and playing back digital
video discs with "two-way" compatibility with the universal DVD video
standard. This means:
•) existing DVD video discs can be played on the recorder.
•) Recordings made on your DVD recorder can be played on other DVD
video players and DVD ROM drives.
?
4
Introduction
Discs you can use
The following discs can be used in your DVD recorder for playback and recording:
Playback and recording
DVD+RW (Digital Versatile Disc + rewritable)
DVD+R (Digital Versatile Disc + Recordable)
Playback only:
DVD Video (Digital Versatile Disc)
DVD-R (DVD-Recordable). These discs can only be played back if the recording was made in video
mode and the recording was finalised.
DVD-RW (DVD-Rewritable) These discs can only be played back if the recording was made in
video mode and the recording was finalised.
Audio CD (Compact Disc Digital Audio)
Super Audio CD (Only plays the CD layer of a hybrid SACD disc)
Video CD (Format 1.0, 1.1, 2.0)
Super Video CD
CD-R (CD-Recordable) Audio/MP3 content
CD-RW (CD-Rewritable) Audio/MP3 content
5
Introduction
Regional code
Since DVD films are not normally released in all parts of the world at the same time, all DVD
players have a specific regional code. Discs can be given a regional code. If the regional codes
differ between the player and the disc, playback is not possible.
DVDs must be marked 'ALL' for all regions or '2' for region 2 to work in this machine. If the DVD
is marked with a different region, it cannot be played in this DVD recorder.
The number within the globe represents the region.
Regional code 2 represents:
Europe, Japan, South Africa, Middle East (incl. Egypt).
Technical data
Voltage : 220-240V/50Hz
Power consumption : 30W
Measurements in cm (W/H/D): 43.5/7.6/33.5 (Disc tray closed), 47.2 (disc tray open)
Weight without packaging approx.: 4.0kg
Power outage/no power: Channel and timer information remain saved for up to 1 year, the
time is saved for up to 12 hours.
Operating position: maximum 10 degree inclination in all directions
Ambient temperature: 15 °C - 35 °C
Humidity: 25% - 75%
Accessories
Operating instructions
Guarantee booklet
Quick install guide
Remote control and batteries
Aerial cable
Mains cable
Scart cable (AV-Euro cable)
G-LINK transmitter
6
Introduction
Important
Caution:
Visible and invisible laser radiation. If the cover is open, do not look at the beam.
Because of the risk of eye injuries, only qualified service engineers should open the machine and
carry out maintenance or repair work.
LASER
Type: Semiconductor lasers InGaAlP (DVD), AlGaAs(CD)
Wavelength: 660nm (DVD), 780nm (CD)
Output power (outside the lens): 20mW (DVD+RW write), 0.8mW (DVD read), 0.3mW (CD
read).
Beam divergence: 82 degrees (DVD), 54 degrees (CD)
Danger. High voltage! Do not open.
You run the risk of getting an electric shock.
The machine does not contain any user-serviceable parts. Please leave all maintenance work to
qualified personnel.
There are some components in the DVD recorder that keep running as long as the recorder is
connected to the power supply. To switch off the DVD recorder completely you must unplug it
from the power supply.
If you disconnect the DVD recorder from the mains, make sure to take the plug out of the wall
socket and not just remove the connector from the 4MAINS socket at the back of the unit.
Children could seriously injure themselves at the free, live end of the cable.
These operating instructions have been printed on non-polluting paper.
Please dispose of old batteries safely.
Please take the packaging to your local recycling centre.
This electronic equipment contains a large number of materials that can be recycled. If you are
disposing of an old machine, please take it to a recycling centre.
7
Introduction
When installing the recorder in a cupboard ensure there is a gap of approximately 2.5 cm (1
inch) around the recorder to enable air to circulate freely and prevent overheating.
Make sure that air can circulate freely through the ventilation slots on the machine. The machine
should be placed on a firm surface.
Make sure that no objects or liquids enter the video recorder. Do not place vases or similar on
the DVD recorder. If you spill liquid in the recorder, immediately disconnect it from the power
supply and call after-sales service for advice.
Keep the DVD recorder away from radiators and other heat sources and protect from direct
sunlight.
Do not place any combustible objects on the device (candles, etc.).
Make sure that children do not place any foreign objects in any of the openings.
Cleaning the discs
Some malfunctions (frozen or distorted picture and broken sound for example) are due to dirt
on the disc. To avoid such problems you should clean your discs regularly.
1
2
Dirty discs should be cleaned with a soft cloth. Always wipe from the
middle to the edge.
Do not use any solvents such as benzine, thinners, commercially
available cleaning agents or antistatic sprays designed for vinyl records.
Can I use a CD lens cleaner in the DVD recorder?
This optical unit (laser) of the DVD recorder operates at a higher power level
than the ones in normal DVDs and CD players so CD lens cleaner discs may
actually damage it.
?
CD lens cleaner discs should therefore not be used.
Special functions of your DVD recorder
Your PhilipsDVD recorder has a number of special functions to make it easier to use and to
enhance your enjoyment.
Philips provides the best possible connection between your DVD recorder and other home
cinema equipment.
The DVD recorder is controlled by external devices (receivers, TV sets and so on) via Cinema Link
and is automatically set to the right system settings.
This function automatically transfers all the television channel settings onto your DVD recorder
via the scart cable ( EXT 1 TO TV-I/O socket).
Recordings made on your DVD recorder can be controlled from an external satellite receiver.
8
Introduction
At the touch of a button your DVD recorder, even though it is switched off, will check which
channel is currently playing on your television and record it.
This connector is also known as a 'FireWire' or 'IEEE 1394'. This connector is used to transmit
wide digital broadband signals that are used for digital video camcorders. Audio and video signals
are transmitted using a cable. In addition to DV and Hi8 camcorders, PCs with digital video output
can also be connected to the digital input.
This screen tells you what's on the disc. Each index screen represents a recording. On the right
hand side of the screen you can also see a disc indicator that shows the position and length of
the current recording on the disc in a graphic format.
This function enables you to simply delete commercials or other scenes. The relevant scenes are
marked and skipped as required. This information is stored on the DVD in such a way that other
DVD players will skip the scenes.
MP3 files are highly compressed music files. The data is compressed to 1/10 of the volume of the
original audio material using a special process. This means that 10 hours of music can be stored
on a single CD.
These music CDs can be played on this machine.
Normally a recording is made at the current disc position. This is the same as for a video cassette,
in the middle of the tape for example. By holding down the REC/OTR n button, the recording
will be made at the end of all the other recordings to avoid overwriting previous recordings.
New recordings on DVD+R discs are always added after all existing recordings.
Using your DVD recorder you can record from an RGB source such as a satellite receiver using
a SCART input ( EXT 2 AUX-I/O socket). Video signals for the colours R(Red), G(Green) and
B(Blue) are transmitted via separate channels. This reduces the interference that occurs with
standard video cables.
The Philips DVD recorder can play back pre-recorded DVDs and CDs. DVDs recorded using this
DVD recorder can be played back on current and future DVD players.
Dolby Digital is a standard developed by Dolby Laboratories for transmitting from 1 to 5
full-range channels as well as a low frequency (.1) channel for a total of 5.1 discrete channels.
The loudspeakers are arranged front left, front middle, front right, rear left and rear right. This
system is currently the most common system and is used in cinemas.
With this DVD recorder each soundtrack in 2-channel Dolby Digital is recorded onto a
DVD+RW.
Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are
trademarks of Dolby Laboratories.
Transmission standard for 5.1 channels from Digital Theatre Systems Inc. This is the second most
wide-spread system after Dolby Digital.
This product contains copy protection technology, which is protected by US Patent Nos.
4631603, 4577216, 4819098 and 4907.093 and other intellectual property rights. Use of this
copy protection technology from Macrovision Corporation requires the approval of Macrovision.
It is intended exclusively for home use and other limited pay-per-view applications, unless
Macrovision approves some other use in writing. Modifications to the equipment, removal of
components and reverse engineering are prohibited.
9
Introduction
The GUIDE Plus+® System gives you an on-screen listing of what's on TV. It also lets you
program your DVD recorder by selecting the show you want to record from the list on your
screen.
You simply enter your local post code during set up and you can see the next 7 days or what's on
right now or even what's on in a favourite category such as sports or movies.
Click with your remote on the show you'd like to see or schedule. No more hassles programming
your DVD recorder! The guide information is sent together with your TV signal so there's nothing
to load or buy. The service is free!
Simple programming system for DVD recorders. Simply enter the programming number
associated with your television programme. You will find this number in your favourite listings
magazine.
GUIDE Plus+, VIDEO Plus+ and PlusCode are trademarks of Gemstar TVGuide International,
Inc. and/or its related affiliates. G-LINK is a trademark of Gemstar-TV Guide International, Inc.
and/or its related affiliates. The GUIDE Plus+ system and the VIDEO Plus+ systemwere
manufactured under licence from Gemstar-TV Guide International, Inc. and/or its related
affiliates.
GEMSTAR;TV GUIDE IS NOT IN ANY WAY LIABLE FOR THE ACCURACY OF
THE PROGRAM SCHEDULE INFORMATION PROVIDED BY THE GUIDE PLUS+
SYSTEM. IN NO EVENT SHALL GEMSTAR;TV GUIDE BE LIABLE FOR ANY
AMOUNTS REPRESENTING LOSS OF PROFITS, LOSS OF BUSINESS, OR
INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH
THE PROVISION OR USE OF ANY INFORMATION, EQUIPMENT, OR SERVICES
RELATING TO THE GUIDE PLUS+ SYSTEM.
The GUIDE Plus+ product, service and/or technology is the subject of various European and
national patents and patent applications owned by, or licensed to, Gemstar - TV Guide
International, Inc. and/or its related affiliates.
Enter the serial number here. You will need it for service queries or if your machine is stolen.
The serial number (PROD. NO.) is printed on the type plate at the back.
MODEL NO.
PROD. NO.
DVDR 80/051
..................
This product complies with the requirements of the following directives and guidelines:
73/23/EEC + 89/336/EEC + 93/68 EEC.
10
Introduction
BConnecting the DVD recorder
Important information for customers in
Great Britain
This set is fitted with an approved moulded 13 amp plug. To change the fuse in this plug or to
attach a different plug, please proceed as follows:
1
2
Take off the fuse cover and remove the old fuse
Insert a new fuse. Suitable fuses are those of the type BS 1362 3A,
A.S.T.A. standard or BSI standard
3
Close the fuse cover
If the attached plug does not meet your requirements, you can cut it off and replace it with a
suitable plug. Please observe the following conditions:
If your new plug uses a built-in fuse, this should be a 3A fuse.
If your new plug does not contain a built-in fuse, please do not use any fuses in your fusebox with a
rating of more than 5A.
Please destroy the old, cut-off plug so that it cannot be used elsewhere.
Connect the blue cable (neutral "N") to the terminal in the plug which is marked with the letter
"N" or coloured black
Connect the brown cable (live, "L") to the terminal in the plug which is marked with the letter
"L" or coloured red
Do not in any circumstances connect either of the two cables to the terminal in the plug which is
marked with the letter "E", the symbol \ or coloured green or green / yellow
Before you refit the plug cover, make sure, that the grip at the bottom of the plug is clamped
over the plastic cover of the lead, not just over the two wires.
Preparing the remote control for
operation
The remote control and its batteries are packed separately in the original DVD recorder
packaging. You must install the batteries in the remote control before use - described in the
following section.
1
Take the remote control and the enclosed batteries (2 batteries).
11
Connecting the DVD recorder
2
Open the battery compartment, insert the batteries as shown and
then close the battery compartment.
The remote control is now ready to use.
Its range is approximately 5 to 10 meters.
'Aim' correctly
In the following sections, you will need the remote control for the first time.
Aim the remote control at the DVD recorder and not at the TV set.
Tip
Connecting your DVD recorder to the TV
set
The necessary cable connections must be made before you can record or playback TV
programmes using your DVD recorder.
Connect the DVD recorder directly to your TV set. If there is a video recorder in between
the picture quality may be poor.
We recommend that you use a scart cable to connect your TV set and DVD recorder.
What is a scart cable?
The scart or Euro AV cable serves as the universal connector for picture,
sound and control signals. With this type of connection, there is practically no
loss of quality in picture or sound transmission.
?
When you install your DVD recorder for the first time, select one of the following options:
'Connecting with a scart cable and EasyLink'
If your TV set is equipped with 'Easy Link, Cinema Link, NexTView Link, Q-Link, Smart Link,
Megalogic, Datalogic, ...' and you wish to use a scart cable.
'Connecting with a scart cable without EasyLink'
If your TV set is not equipped with 'Easy Link, Cinema Link, NexTView Link, Q-Link, Smart Link,
Megalogic, Datalogic, ...' and you wish to use a scart cable.
'Connecting with an S;Video(Y/C)cable'
If your TV set is equipped with an S-Video(SVHS) socket.
'Connecting with video(CVBS) cable'
If your TV set is equipped only with an video(CVBS) socket.
12
Connecting the DVD recorder
Connecting with a scart cable and 'Easy
Link'
Your DVD recorder can exchange information with your TV set using 'Easy Link'. Your TV
channels can also be transferred in the same order from your TV set to your DVD recorder
using 'Easy Link'.
Please see your TV's operating instructions.
Have the following cables ready:
an aerial cable (1, supplied), a mains cable (2, supplied), a special scart cable (3, suitable for
Easylink).
1
2
Switch off your TV set.
Remove the aerial cable plug from your TV set. Insert it into the
ANTENNA IN socket at the back of the DVD recorder.
3
Insert one end of the supplied aerial cable into the TV OUT socket at
the back of the DVD recorder and the other end into the aerial input
socket at the back of the TV set.
4
5
Plug in a full-pin scart cable (all 21 contacts wired) into the scart
socket EXT 1 TO TV-I/O at the back of the DVD recorder and the
corresponding scart socket - suitable for Easylink - at the back of the
TV set (see TV set operating instructions).
Read the next chapter 'Connecting additional devices' on how to
connect additional devices (satellite receivers, videorecorders,...) to the
input-/output sockets.
6
7
Switch on the TV set.
Use the supplied mains cable to connect the mains socket
4MAINS at the back of the DVD recorder with the wall outlet.
The most important features of the DVD recorder will appear in
scrolling text on the display. After the first installation is completed
this function will be switched off. How you switch on this function
again, read in the chapter 'User preferences' in the section 'standby'.
13
Connecting the DVD recorder
8
9
Switch on the DVD recorder using STANDBY-ON m .
A message appears on the screen announcing that the transfer has
started. 'EASYLINK' appears on the display during transfer.
The TV set transfers all saved TV channels, in the same order, to the
DVD recorder
EasyLink
loading data from TV;
please wait
This may take several minutes.
After the data transfer has been completed,, the following appears on
the screen: 'EasyLink loading complete'.
a'Time', 'Year', 'Month', 'Date' appears on the TV screen
1
2
Check if the time in 'Time' is correct.
If required, change the time with the number buttons 0..9 on your
remote control.
3
4
Select the next line with P+ A or P- B .
Check if the displayed settings for 'Year', 'Month' and 'Date' are
correct.
5
When all information is correct, save by pressing OK .
Problem
aI can see more installation menus on myTV set
Virgin mode
Not all the necessary data has been transferred. Please enter the settings
by hand as follows. For more information on the various functions see
'Initial installation' in 'Installing your DVD recorder'.
Audio Language
English
Español
Français
Português
Italiano
1
Select the desired audio language using P- B or P+ A and confirm
with OK .
Select the desired subtitle language with P- B or P+ A and confirm
with OK .
2
3
Press OK to continue
Select the desired screen format position using P- B or P+ A .
'4:3 letterbox' For a 4:3 TV set; cinema format (black bars above and
below the picture)
'4:3 panscan' For a 4:3 TV set; full height format with the sides cut off
'16:9' For a 16:9 TV set
4
5
Confirm with OK .
Select the country of your residence with P- B or P+ A .
If your country does not appear, select 'Other'.
Confirm with OK .
6
Problem
This completes the basic setup.
Further settings relate to the GUIDE Plus+® system. This offers a free interactive guide to the
TV programmes available in your area.
To install this system, please read the instructions in the section entitled 'The GUIDE Plus+®
System'.
14
Connecting the DVD recorder
Connecting with a scart cable without
'EasyLink'
Have the following cables ready:
an aerial cable (1, supplied), a mains cable (2, supplied), a scart cable (3).
1
2
3
Remove the aerial cable plug from your TV set. Insert it into the
ANTENNA IN socket at the back of the DVD recorder.
Insert one end of the supplied aerial cable into the TV OUT socket at
the back of the DVD recorder and the other end into the aerial input
socket at the back of the TV set.
Plug a scart cable into the scart socket EXT 1 TO TV-I/O at the
back of the DVD recorder and the scart socket for the DVD
recorder at the back of the TV set (see TV set operating instructions).
MyTV set has several scart sockets. Which one should I use?
Select the scart socket that is suitable for both video output and for video
input.
MyTV set shows me a selection menu for the scart socket
?
Select 'VCR' as the source for this scart socket.
4
Read the next chapter 'Connecting additional devices' on how to
connect additional devices (satellite receivers, videorecorders,...) to the
input-/output sockets.
5
6
Switch on the TV set.
Insert one end of the supplied mains cable into the mains socket
4MAINS at the back of the DVD recorder and the other end into
the wall socket.
The most important features of the DVD recorder will appear in
scrolling text on the display. After the first installation is completed
this function will be switched off. How you switch on this function
again, read in the chapter 'User preferences' in the section 'standby'.
7
Switch on the DVD recorder using STANDBY-ON m . 'IS TV ON?'
will appear on the display.
15
Connecting the DVD recorder
8
If the connection was properly made and your TV was automatically
switched to the programme number for the scart socket, e.g. 'EXT',
'0', 'AV', you will see the following picture:
aMyscreen is empty.
Virgin mode
b Many TV sets are switched by the DVD recorder to the programme
number for the scart socket by way of a control signal sent through the
scart cable.
Menu Language
English
Español
Français
Italiano
b If the TV set does not automatically switch to the scart socket programme
number, manually change to the corresponding programme number on your
TV set (see your TV's operating instructions).
Deutsch
Press OK to continue
b Check that the scart cable is connected from the TV set to the EXT 1
TO TV-I/O socket on the DVD recorder. The EXT 2 AUX-I/O socket is
intended only for additional devices.
Problem
Then, read the paragraph on 'Initial installation' in 'Installing your DVD recorder'.
Connecting with an S;Video(Y/C)cable
This connecting cable, also known as the SVHS cable, is used to transmit the brightness signal (Y
signal) and colour signal (C signal) separately. This mini DIN socket/plug is also called a Hosiden
socket/plug.
Have the following cables ready:
an aerial cable (1, supplied), a mains cable (2, supplied), an S-Video(SVHS) cable (3), an audio
cable (4, supplied, red/white plug).
1
2
3
Remove the aerial cable plug from your TV set. Insert it into the
ANTENNA IN socket at the back of the DVD recorder.
Insert one end of the supplied aerial cable into the TV OUT socket at
the back of the DVD recorder and the other end into the aerial input
socket at the back of the TV set.
Insert one end of an S-Video(SVHS) cable into the OUT S-VIDEO
(Y/C) socket at the back of the DVD recorder and the other end into
the S-Video (SVHS) input socket on the TV set (usually labelled
'S-Video in' or 'SVHS in'. See TV operating instructions).
16
Connecting the DVD recorder
4
Insert one end of the supplied audio (Cinch) cable into the red/white
Cinch socket OUT AUDIO L/R at the back of the DVD recorder
and the other end into the audio input socket (usually red/white) on
the TV set (usually labelled 'Audio in' or 'AV in'. See TV operating
instructions).
5
6
Switch on the TV set. Switch the TV set over to the SVHS input
socket or select the relevant programme number. Please see your
TV's operating instructions for the programme number you need.
Insert one end of the supplied mains cable into the mains socket
4MAINS at the back of the DVD recorder and the other end into
the wall socket.
The most important features of the DVD recorder will appear in
scrolling text on the display. After the first installation is completed
this function will be switched off. How you switch on this function
again, read in the chapter 'User preferences' in the section 'standby'.
7
Switch on the DVD recorder using STANDBY-ON m . IS TV ON?'
will appear on the display.
Then, read the paragraph on 'Initial installation' in 'Installing your DVD recorder'.
Connecting with video(CVBS) cable
This cable, usually with yellow Cinch connectors, is used for transmitting the Composite Video
signal (FBAS, CVBS). In this method of transmission the colour signal and the brightness signal
are transmitted on the same cable. In certain circumstances, this can lead to problems with the
picture, such as 'Moiré' patterns.
Have the following cables ready:
an aerial cable (1, supplied), a mains cable (2, supplied), a video (CVBS)cable (3, supplied, yellow
plug), an audio cable (4, supplied, red/white plug).
1
2
Remove the aerial cable plug from your TV set. Insert it into the
ANTENNA IN socket at the back of the DVD recorder.
Insert one end of the supplied aerial cable into the TV OUT socket at
the back of the DVD recorder and the other end into the aerial input
socket at the back of the TV set.
17
Connecting the DVD recorder
3
4
Insert one end of the supplied video (CVBS) cable into the yellow
Cinch socket VIDEO (CVBS) OUT at the back of the DVD
recorder and the other end into the video input socket (usually
yellow) on the TV set (usually labelled 'Video in' or 'AV in'. See TV
operating instructions).
Insert one end of the supplied audio (Cinch) cable into the red/white
Cinch socket OUT AUDIO L/R at the back of the DVD recorder
and the other end into the audio input socket (usually red/white) on
the TV set (usually labelled 'Audio in' or 'AV in'. See TV operating
instructions).
5
6
Read the next chapter 'Connecting additional devices' on how to
connect additional devices (satellite receivers, videorecorders,...) to the
input-/output sockets.
Switch on the TV set. Switch the TV set over to the Video/Audio
input socket or select the relevant programme number. Please see
your TV's operating instructions for the programme number you need.
7
Insert one end of the supplied mains cable into the mains socket
4MAINS at the back of the DVD recorder and the other end into
the wall socket.
The most important features of the DVD recorder will appear in
scrolling text on the display. After the first installation is completed
this function will be switched off. How you switch on this function
again, read in the chapter 'User preferences' in the section 'standby'.
8
Switch on the DVD recorder using STANDBY-ON m . 'IS TV ON?'
will appear on the display.
Then, read the paragraph on 'Initial installation' in 'Installing your DVD recorder'.
18
Connecting the DVD recorder
CConnecting additional devices
Connecting additional devices to the
second scart socket
You can connect additional devices such as decoders, satellite receivers, camcorders, etc. to the
EXT 2 AUX-I/O socket. When playback is started on this additional device the DVD recorder
automatically connects the EXT 2 AUX-I/O scart socket with the EXT 1 TO TV-I/O scart
socket. You will then see the picture from the additional device on your TV set, even if the
DVD recorder is switched off.
The TV/DVD button on the remote control allows you to switch between playback through the
EXT 2 AUX-I/O scart socket and playback from the DVD recorder.
The DVD recorder must be connected directly to the TV set ( EXT 1 TO TV-I/O socket
directly to the TV set). If there is a video recorder in between the picture quality may be poor
because of the copy protection system built into the DVD recorder.
Connecting a video recorder, DVD player.
You can connect a video recorder or a DVD player to the EXT 2 AUX-I/O input socket. If you
already have an external receiver (satellite receiver, set-top box, cable TV box) connected to this
socket, you can connect the video recorder to the 'VCR', 'TO VCR', ...socket of the external
receiver.
You can also use the front sockets S-VIDEO , VIDEO and the left AUDIO right audio
sockets.
Please note:
Most prerecorded video cassettes and DVDs are copy-protected. If you try to copy them you
will see the message 'COPY PROT' on the DVD recorder's display.
aWhen copying video cassettes the display on the DVD recorder
shows 'NO SIGNAL'
b Check that the cable is plugged in firmly.
b If a recording is made from a video recorder, change the tracking on the
video recorder.
b The DVD recorder may not be able to recognise the video input signal if
this signal is poor or does not comply with relevant standards.
aWhen I copyDVD video discs or prerecorded video cassettes the
picture is fuzzyand the brightness varies
b This happens if you try to copy DVDs or video cassettes that have been
copy-protected. Even though the picture on the TV is fine the recording on
a
DVD+R/RW is faulty. This interference is unavoidable with
Problem
copy-protected DVDs or video cassettes.
Connecting an external receiver (satellite
receiver, set;top box, cable TV box,...)
You can connect external receivers to the EXT 2 AUX-I/O socket.
For additional receivers, you can also use the EXT 1 TO TV-I/O socket (if the TV set is
connected to the COMPONENT VIDEO OUT sockets), and VIDEO , S-VIDEO sockets at
the front. Please observe that you also have to connect an audio cable to the IN AUDIO
L/R or left AUDIO right socket.
19
Connecting additional devices
1
Connect the scart socket of the receiver (satellite receiver) provided
for the TV set (usually labelled 'TV', 'TO TV'), with the EXT 2
AUX-I/O socket of the DVD recorder.
Whycan't I use the 'VCR', 'TO VCR',... socket?
In order to achieve the best possible picture quality, you must use the RGB
(red-green-blue) signal of the receiver. As a rule, this signal is available at the
'TV', 'TO TV',... socket. The DVD recorder transfers the signal to the EXT 1
TO TV-I/O socket.
Some receivers only provide a 'Video (CVBS/FBAS)' signal at the 'VCR', 'TO
VCR'...socket. Read the instruction manual of the receiver on the signals
available at the sockets.
If you are satisfied with the picture quality of the 'VCR', 'TO VCR',... socket,
you can also use this socket.
?
2
If your external receiver offers several options for the signal available
at the 'TV', 'TO TV',... socket, choose the 'RGB' setting.
Connecting additional devices onlyvia
aerial cable
If you want to connect additional devices (e.g. satellite receiver...) only via aerial cable, please
observe the following:
The DVD-Recorder must be connected directly to the TV set. If there is a video recorder or an
additional device in between, the picture quality may be poor because of the copy protection
system built into the DVD-Recorder.
The additional device (satellite receiver) must be connected before the DVD recorder (additional
device - DVD recorder - TV set). Only the TV set must be connected to the TV OUT socket.
•) If there is interference in the picture when the additional device is switched on, a TV
broadcaster may be transmitting on the same channel or a channel very close to that of the
additional device. (e.g.: TV broadcaster on channel 45, additional device (satellite receiver) also
on channel 45). In this case, change the channel of the additional device (satellite receiver).
Consult the instruction manual of the additional device.
You must also store this channel on the DVD recorder to be able to record TV programmes
from the additional device (satellite receiver).
•) Switch on the additional device during the installation of the DVD recorder. During the
automatic channel search, the channel on which the additional device is transmitting will be
stored as a TV channel.
20
Connecting additional devices
Connect camcorder to the front sockets
To copy camcorder recordings, you can use the front sockets. These sockets are located behind
the flap on the right hand side.
Best picture quality
If you have a DV or Digital 8 camcorder, connect the DV IN input of the DVD recorder to the
appropriate DV output on the camcorder.
When films are transferred the original recording date and time are stored as DVD subtitles.
On playback, this data can be displayed on the TV screen by using the '
' function (Subtitle).
E
Choose 'CAM2' as a programme number for this input.
Verygood picture quality
If you have a Hi8 or S-VHS(C) camcorder, connect the S-VIDEO input of the DVD recorder to
the appropriate S-VHS output on the camcorder.
You must also connect the audio input left AUDIO right on the DVD recorder to the audio
output on the camcorder.
Choose 'CAM1' as a programme number for this input.
Good picture quality
If you have a camcorder that only has a single video output (Composite Video, CVBS), connect
the VIDEO input on the DVD recorder to the appropriate output on the camcorder.
You must also connect the audio input left AUDIO right on the DVD recorder to the audio
output on the camcorder.
Choose 'CAM1' as a programme number for this input.
Connecting audio devices to the analogue
audio sockets
Two audio output sockets OUT AUDIO L/R are located on the back of the DVD recorder
(audio signal output left/right)
These can be used to connect the following:
•) a receiver with DolbySurround Pro Logic
•) a receiver with two;channel analogue stereo
Can I use the 'Phono' input on myamplifier?
This socket (input) on the amplifier is designed only for record players
without preamplifiers. Do not use this input for connecting the DVD
recorder.
?
The DVD recorder or the amplifier may be damaged as a result.
21
Connecting additional devices
Connecting audio devices to the digital
audio sockets
At the back of the DVD recorder there are two digital audio output sockets OPTICAL
AUDIO OUT for an optical cable and COAX OUT for a coaxial cable (Cinch cable).
These can be used to connect the following:
•) an A/V receiver or an A/V amplifier with a digital multi;channel sound decoder
•) a receiver with two;channel digital stereo (PCM)
Digital multi;channel sound
Digital multi-channel sound offers the best possible sound quality. You will
need a multi-channel A/V receiver or amplifier that supports at least one of
the audio formats of the DVD recorder (MPEG2, Dolby Digital and DTS).
Consult the operating instructions for your receiver to find out which audio
?
formats it supports.
aAll I can hear from myloudspeakers is a loud distorted noise
b The receiver is not compatible with the digital audio format of the DVD
recorder. The audio format of the DVD disc is displayed in the status
window when you switch to another language. Playback in six-channel
digital surround sound is only possible if the receiver has
multi-channel sound decoder.
a
digital
Problem
22
Connecting additional devices
DInstalling your DVD recorder
Initial installation
After successfully connecting your DVD recorder to the TV set and other additional devices as
described in the previous chapters, this chapter will show you how to start the initial installation.
The DVD recorder automatically seeks out and stores all available TV channels.
Connecting additional devices
If you have connected additional devices such as a satellite receiver to the
aerial cable, switch them on. The automatic channel search will recognise it
and save it. Please observe that you must switch on a "test signal" for some
additional devices.
No aerial connected
Even if you only want to use the DVD recorder to play back or have only
connected a satellite receiver, you must still complete the initial installation.
This is necessary so that the basic settings are stored correctly. Once initial
Tip
installation is complete you can use the DVD recorder as normal.
1
Select the desired language for the on-screen menu by pressing
P- B or P+ A .
Virgin mode
Virgin mode
Virgin mode
Menu Language
English
Español
What is an on;screen menu?
The multi-language on-screen menu takes the mystery out of using your new
DVD recorder. All settings and/or functions are displayed on your TV screen
in the relevant language.
Français
Italiano
Deutsch
Press OK to continue
?
?
?
2
3
Confirm with OK .
Select the desired audio language using P- B or P+ A .
What is an audio language?
Audio Language
English
Español
Français
Português
Italiano
The DVD will play the sound in the language you select, provided this
language is available on the disc. If it is not available on the disc the first
language on the DVD will be used instead. The DVD Video Disc menu, if
available, will also be displayed in the language you select.
Press OK to continue
4
5
Confirm with OK .
Select the desired language for the subtitles by pressing P- B or
P+ A .
Subtitle Language
English
Español
Français
Português
What is the subtitle language?
The subtitles will be displayed in the language you select, provided this
language is available on the disc. If it is not available on the disc the fist
language on the DVD will be used instead.
Italiano
Press OK to continue
6
Confirm with OK .
23
Installing your DVD recorder
7
Select the desired screen format position using P- B or P+ A .
These settings will only be used if you insert a DVD that contains this
information.
Virgin mode
TV Shape
4:3 letterbox
4:3 panscan
16:9
Which screen formats can I select?
'4:3 letterbox' for a 'wide-screen' (cinema format) picture with black bars at
the top and bottom.
Press OK to continue
'4:3 panscan' for a full-height picture with the sides trimmed.
?
?
'16:9' for a wide-screen TV set (screen edge ratio 16:9)
8
9
Confirm with OK .
Select the country of your residence with P- B or P+ A .
If your country does not appear, select 'Other'.
Virgin mode
Country
Austria
Belgium
Denmark
Finland
Whydo I have to select a country?
To call up the specific settings for the respective country, you must first install
the country.
France
Press OK to continue
0
A
Confirm with OK .
After you connect the aerial (or cable TV, satellite receiver, etc.) to
the DVD recorder, press OK .
'Autoinstall' starts. 'WAIT' will appear on the display. The following
appears on the screen:
aThe DVD recorder cannot find anyTV stations
b Select channel 1 on the TV set. Can you see the stored TV channel on the
TV set?
If not, check the cable connection from the aerial (aerial socket) to the
DVD recorder and to the TV set.
b Please have patience.
The DVD recorder searches the entire frequency range in order to find
and save the largest possible number of TV channels.
b If you have not connected an aerial, go through all the basic settings right
to the end and then, if you wish, start the automatic search (see next
chapter 'Automatic TV programme search (Autoinstall)').
Problem
B
C
À
Wait until all available TV channels have been found. This can take
several minutes.
When AUTOINSTALL is complete, 'Autoinstall complete' will
briefly appear on the TV screen.
To end, press SYSTEM-MENU .
Check the date and time. Please read 'Setting the time and date' in
this chapter.
24
Installing your DVD recorder
Satellite receiver
If you are connecting a satellite receiver, please read the section on 'Using a
satellite receiver'.
Decoder
If you are connecting a decoder, you must install it as described in the next
section.
Tip
aSound maybe distorted on some TV channels.
b If the sound is distorted on any of the stored TV channels or if there is no
sound at all, the wrong TV system may have been stored for the TV
channel. Read 'Manual TV channel search' for information on how to
change the TV system.
Problem
Further settings relate to the GUIDE Plus+® System. This offers a free interactive guide to the
TV programmes available in your area.
To install this system, please read the instructions in the section entitled 'The GUIDE Plus+®
System'.
Using a satellite receiver
TV channels from a satellite receiver (connected to scart socket EXT 2 AUX-I/O ) are received
on the DVD recorder on programme number 'EXT2'
If necessary, use the MONITOR button to switch to the internal tuner.
Select programme number 'EXT1' with 0 on the remote control and then select programme
number 'EXT2' with P- B .
You should select the TV channels to be received by the satellite receiver directly on the
receiver itself.
25
Installing your DVD recorder
Allocating a decoder
Some TV channels send coded TV signals that can only be viewed properly with a purchased or
rented decoder. You can connect such a decoder (descrambler) to your DVD recorder. The
following function automatically activates the connected decoder for the TV chann
watch.
How do I allocate the decoder for EasyLink?
If your TV set supports 'Easy Link' the decoder must be assigned to the
relevant TV channel on the TV set (see the operating instructions for your TV
set). Settings cannot then be made in this menu.
?
1
Switch on the TV set. If required, select the programme number for
the DVD recorder.
2
3
Switch on the DVD recorder using STANDBY-ON m .
Use the P+ A and P- B buttons or the number buttons 0..9 on
the remote control to select the TV channel for which you want to
use the decoder. If necessary, use the MONITOR button to switch to
the internal tuner.
4
Press the SYSTEM-MENU button on the remote control. The menu
bar appears.
5
6
7
Select ' ' symbol with D or C .
A
Select 'Installation' using P- B or P+ A and confirm with C .
Select 'Manual search' using P- B or P+ A and confirm with C .
8
9
Select 'Decoder' using P- B or P+ A .
Installation
Manual search
Select 'On' with D or C .
Channel/freq.
Entry/search
CH
01
Programme number 01
TV channel name
Decoder
BBC1
How do I switch the decoder off again?
Off
?
Use C to select 'Off' in the 'Decoder' line on the screen (Decoder off).
TV system
NICAM
PAL-BG
On
0
To store
Press OK
Fine tuning
0
A
Confirm with OK .
To end, press SYSTEM-MENU .
Your decoder has now been allocated to this TV channel.
26
Installing your DVD recorder
Connection using a component video
(Y Pb Pr/YUV) cable
Component video (Y Pb Pr) is the highest quality picture transmission option. This is achieved by
dividing the video signal into a luminance signal (Y) and two colour difference signals - red minus
luminance (U) and blue minus luminance (V). As a rule, "Cr" or "R-Y" is used to describe the red
difference signal and "Cb" or "B-Y" the blue difference signal.
These signals are transmitted through separate lines. The connectors of this cable and the
corresponding sockets are usually green (luminance), blue (Pb, Cb, B-Y), and red (Pr, Cr, R-Y).
If you choose this type of connection, the DVD recorder must already be connected and
completely installed (initial installation complete).
Switching of the signal to the COMPONENT VIDEO OUT sockets is carried out in a menu
that is not yet available during the initial installation.
Moreover, the installation of the GUIDE Plus+® system must also be completed (local post code
must be entered).
1
Switch on the TV set. If required, select the programme number for
the DVD recorder.
2
3
Switch on the DVD recorder using STANDBY-ON m .
Press the SYSTEM-MENU button on the remote control. The menu
bar appears.
4
5
Select ' ' using D oder C and confirm with P- B .
A
Select the ' ' symbol using P- B or P+ A and confirm with C .
t
6
7
Select the line 'Video output' using P+ A or P- B and confirm
with C .
Select your setting with P- B or P+ A .
Picture
TV shape
16:9
Off
Black level shift
Video shift
Which setting should I choose?
ï
Since YPbPr (YUV) signals are not transmitted simultaneously with
S-video(Y/C) and video (FBAS/CVBS) signals, you can choose between the two
types. The 'RGB' signal is switched off.
Video output
RGB + CVBS
'S-video + YPbPr' Component Video (YUV) and S-Video(Y/C).
On the socket OUT S-VIDEO (Y/C) no GUIDE Plus+®
menus.
'CVBS + YPbPr'Component Video (YUV) and Video (FBAS/CVBS).
On the socket VIDEO (CVBS) OUT no GUIDE Plus+®
menus.
With all other settings, the signal is switched off at the COMPONENT
VIDEO OUT sockets. This will also be displayed as information on the screen.
For more information on the other settings, read section 'Picture settings'
('Video output') in chapter 'User preferences'.
?
8
Confirm with OK .
27
Installing your DVD recorder
9
Use a component video (Y Pb Pr) cable, connect the three cinch
sockets (red, blue, green) COMPONENT VIDEO OUT at the back
of the DVD recorder with the corresponding three component video
input sockets of your TV set, usually labelled 'Component Video
Input', 'YUV Input', 'YPbPr', 'YCbCr' or simply 'YUV'.
Warning!
Do not confuse these sockets with the five-component RGB sockets
(if available) or the yellow video (CVBS/FBAS) socket and the two
audio sockets (red/white). The five-component RGB sockets are only
provided for the R-G-B-H-V signals (red, green, blue with horizontal
and vertical synchronisation impulse).
Please observe the colour sequence
The colours of the sockets at the DVD recorder and the connectors must
match
those
of
the
socket
colours
at
the
TV
set
(red-red/blue-blue/green-green). If they don't, the colours of the picture may
get mixed up or the picture may not be visible.
Tip
0
Use an audio (cinch) cable, connect the red/white cinch socket OUT
AUDIO L/R at the back of the DVD recorder with the mostly
red/white audio input socket of your TV set (usually labelled 'Audio in'
or 'AV in'. See the instruction manual of your TV set.)
A
B
If necessary, switch your TV set to the component video input socket.
Also consult the instruction manual of your TV set.
The menu of the DVD recorder should now appear on the TV
screen. If not, check the cable connections and the settings on your
TV set.
Manual TV channel search
In some cases, not all of the available TV channels may have been found and stored during initial
installation. In this case, you will need to search for and store the missing or coded TV channels
manually.
Manual search with EasyLink
With 'Easy Link', the DVD recorder will automatically download the TV
channels stored on the TV set. This is why some lines have no function. To
store new TV channels, they must first be stored on the TV set. The
Tip
information will then be transferred to the DVD recorder automatically.
1
2
Switch on the TV set. If required, select the programme number for
the DVD recorder.
Switch on the DVD recorder using STANDBY-ON m .
28
Installing your DVD recorder
3
Press SYSTEM-MENU on the remote control. The menu bar
appears.
4
5
6
Select ' ' symbol with D or C .
A
Select 'Installation' using P- B or P+ A and confirm with C .
Select 'Manual search' using P- B or P+ A and confirm with C .
7
8
In 'Channel/freq.', select the desired display using C .
'Freq.'(Frequency), 'CH'(Channel), 'S-CH'(Special/hyperband channel)
Installation
Manual search
Channel/freq.
Entry/search
CH
01
In 'Entry/search', enter the frequency or channel of the TV station
using the number buttons 0..9 .
Programme number 01
TV channel name
Decoder
BBC1
Off
TV system
NICAM
PAL-BG
aI don't know the channel for myTV station
b In this case, press C to start the automatic search. A changing channel
number/frequency number will appear on the TV screen.
Continue the automatic search until you have found the TV channel you
are looking for.
On
0
To store
Press OK
Fine tuning
Problem
9
Using D or C in 'Programme number', select the programme
number you want to use for the TV channel, e.g. '01'.
How can I change the namel of a TV channel?
1
2
3
4
5
In 'TV channel name', press C .
Select the desired character position using D or C .
Change the character at the desired position with P- B or P+ A .
Select the next character position in the same way.
Confirm with OK .
Tip
How can I change the TV system of the TV channel?
In 'TV system', use D or C to select the TV system that produces the
least distortion of picture and sound.
What is NICAM?
NICAM is
a
digital sound transmission system. Using NICAM, you can
transmit either 1 stereo channel or 2 separate mono channels. However, if
reception is poor and the sound distorted you can turn off NICAM.
In 'NICAM', select 'Off' using D or C .
How can I improve the automatic process for storing channels?
To change the automatic process for storing channels (fine tuning), select
'Fine tuning'.
Using D or C you can try to fine-tune the TV channelmanually.
Tip
0
A
B
Press OK to store the TV channel.
To search for other TV channels, begin again at 8 .
To end, press SYSTEM-MENU .
29
Installing your DVD recorder
Sorting TV channels automatically
(Follow TV)
When the automatic channel search function is activated, the TV channels are stored in a specific
order. This may differ from the order in which the TV channels appear on your TV set.
This function changes the order of the TV channels stored in your DVD recorder to match the
order on the TV set.
This only works if the DVD recorder ( EXT 1 TO TV-I/O socket) and the TV set are
connected with a scart cable.
MyTV set has Easylink
If your TV set supports 'Easylink,..', TV channels will be stored during initial
installation in the same order as they appear on the TV set. To store the TV
channels in a different order, you'll need to change the order on the TV set.
When you start the Follow TV function the information is transferred again
Tip
from the TV set.
1
Switch on the TV set. If required, select the programme number for
the DVD recorder.
2
3
Switch on the DVD recorder using STANDBY-ON m .
Press the SYSTEM-MENU button on the remote control. The menu
bar appears.
4
5
6
Select ' ' symbol with D or C .
A
Select 'Installation' using P- B or P+ A and confirm with C .
Select line 'Follow TV' with P- B or P+ A . and confirm with the
C button.
7
8
Confirm the message on the screen with OK . 'TV 01' will appear in
the DVD recorder display.
Select programme number '1' on the TV set.
TV 01
aI cannot switch myTV set to programme number '1'
b If you have connected additional devices to the EXT 2 AUX-I/O socket,
please disconnect these devices. Other connected devices may have
switched the TV set to the programme number of the scart socket.
Problem
9
Confirm with OK on the DVD recorder remote control.
'WAIT' will appear in the display. The DVD recorder compares the TV
channels on the TV set and the DVD recorder.
If the DVD recorder finds the same TV channel as on the TV set it
stores it at 'P01'.
30
Installing your DVD recorder
a'NOTV' will appear in the display. The DVD recorder is not
receiving a video signal from the TV set.
b Chech the connectors at both ends of the scart cable.
b Check your TV's operating instructions to see which scart socket is used
for video signals.
b If the problem persists, you won't be able to use this feature.
Please read 'Sorting and deleting TV channels manually'.
Problem
0
Wait until for example 'TV 02' appears in the display.
A
B
Select the next programme number on the TV set, e.g. '2'.
TV 02
Confirm with OK on the DVD recorder remote control.
Deleting sorting
Tip
You can delete incorrect TV channel sorting by pressing D .
C
À
Repeat steps 0 to B until you have assigned all the TV channels.
To end, press SYSTEM-MENU .
a'New preset, please switch to standby' appears on the screen
b In order to transfer the new TV channel order to the GUIDE Plus+®
system, it is necessary to switch off the DVD recorder ( STANDBY m ).
Wait for approx. 4 minutes before you switch the DVD recorder on again.
b If this message appears after you switch on the DVD recorder, it was not
possible to complete the transfer process. Switch off the DVD recorder
using STANDBY m .
Problem
31
Installing your DVD recorder
Automatic TV channel search
(Autoinstall)
During installation, all available TV channels are searched for and stored. If the channel
assignments of your cable or satellite TV provider change or if you are reinstalling the DVD
recorder, e.g. after moving house, you can start this procedure again. This will replace the stored
TV channels with the new ones.
MyTV set has Easylink
With Easylink, you can search for and store TV channels only on the TV set.
These settings are accepted by the DVD recorder. Use this function to start
the transfer of TV channels from the TV set.
Tip
1
Switch on the TV set. If required, select the programme number for
the DVD recorder.
2
3
Switch on the DVD recorder using STANDBY-ON m .
Press the SYSTEM-MENU button on the remote control. The menu
bar appears.
4
5
6
7
Select ' ' symbol with D or C .
A
Select 'Installation' using P- B or P+ A and confirm with C .
Select 'Autoinstall' using P- B or P+ A .
Press C .
8
9
'Autoinstall' starts. Wait until all the TV channels have been found.
This can take several minutes.
Installation
Autoinstall
Searching for TV channels
When Autoinstall has finished, 'Autoinstall complete' will appear on
the TV screen.
00 Channels found
0
A
The date and time have been set and stored.
Please wait
To end, press SYSTEM-MENU .
You can read about how to search for a TV channel manually in 'Manual TV channel search'.
32
Installing your DVD recorder
Sorting and deleting TV channels manually
After you have performed the automatic channel search you may not agree with the sequence in
which the individual TV channels have been allocated to the programme positions (programme
numbers). You can use this function to rearrange the TV channels already stored or to delete
TV channels you don't want or those with poor reception.
EasyLink
With Easylink, you can search for and store TV channels only on the TV set.
These settings are then transferred to the DVD recorder.
That is why you cannot select this function manually.
The teletext clock resets automatically
If you store a TV channel which transmits TXT/PDC on programme number
'P01', the date and time will automatically be transmitted and constantly
updated. As a result, the changes from summer time to winter time and back
Tip
again will be made automatically.
1
2
Switch on the TV set. If required, select the programme number for
the DVD recorder.
Switch on the DVD recorder. Press the SYSTEM-MENU button on
the remote control. The menu bar appears.
3
4
5
Select ' ' symbol with D or C .
A
Select 'Installation' using P- B or P+ A and confirm with C .
Select 'Sort TV channels' using P- B or P+ A and confirm with
C .
6
7
Using P- B or P+ A select the TV channel that you want to delete
or whose order you want to change.
Installation
Sort TV channels
...
•
P01 BBC1
P02 BBC2
P03 ITV
P04
Confirm with C .
P05
Deleting TV channels
P06
Unwanted channels or those with poor reception can be deleted using
CLEAR . Proceed at step 6 .
...
Tip
To sort
Press ›
To exit press
SYSTEM MENU
8
9
Using P- B or P+ A , shift the TV channel to the desired position
and press the D button. The DVD recorder will insert the TV
channel.
Repeat steps 6 to 8 until you have resorted/deleted all the TV
channels you want.
0
A
To store, press OK .
To end, press SYSTEM-MENU .
33
Installing your DVD recorder
a'New preset, please switch to standby' appears on the screen
b In order to transfer the new TV channel order to the GUIDE Plus+®
system, it is necessary to switch off the DVD recorder ( STANDBY m ).
Wait for approx. 4 minutes before you switch the DVD recorder on again.
b If this message reappears after you switch on the DVD recorder, it was not
possible to complete the transfer process.
Problem
Switch off the DVD recorder using STANDBY m .
Setting the language
For the basic setting of DVD playback, you can select the language for the subtitles and the
audio language. Please note that with some DVDs the audio language and/or subtitle language can
be changed only via the DVD menu.
For bilingual shows, you can also select the sound channel of the TV station via the internal
tuner ( MONITOR button) for recording or playback.
You also have the option of setting one of the displayed languages for the on-screen menu
(OSD). However, the DVD recorder display will only display English text regardless of this
setting.
1
Switch on the TV set. If required, select the programme number for
the DVD recorder.
2
3
Switch on the DVD recorder using STANDBY-ON m .
Press SYSTEM-MENU on the remote control. The menu bar
appears.
4
5
Select ' ' symbol with D or C .
A
Select line 'Language' with P- B or P+ A and confirm with the
C button.
6
Select the appropriate line and confirm with C .
Which settings can I choose?
Language
Audio Language
Recording audio
Subtitle
English
'Audio Language' : The DVD will play back in the language you have chosen.
'Recording audio' : In the case of bilingual programmes, you can choose
either 'Language 1' or 'Language 2' as the default
setting
Language 1
English
Menu
English
'Subtitle' : Subtitle language
'Menu': Language of the OSD menu
Tip
7
8
Select the appropriate setting using P- B or P+ A and confirm with
OK .
To end, press SYSTEM-MENU .
34
Installing your DVD recorder
'Recording audio' switching over
(2;channel sound)
Some TV programmes transmit an extra audio signal in stereo in addition to the normal audio
signal (2-channel sound). In most cases this means that an additional language is available. If a TV
programme is available in, say, English and German, German may be available as the second
language.
To record TV programmes in 2-channel sound, you can select the language you want as the
default setting. This setting does not become active until the sound of a TV programme is
transmitted in 2-channel sound.
When you play back the recording you can play back the sound only in the language you used
for the recording.
1
Switch on the TV set. If required, select the programme number for
the DVD recorder.
2
3
Switch on the DVD recorder using STANDBY-ON m .
Press SYSTEM-MENU on the remote control. The menu bar
appears.
4
5
Select ' ' symbol with D or C .
A
Select line 'Language' with P- B or P+ A . and confirm with the
C button.
6
7
Select line 'Recording audio' and confirm with C .
Language
Audio Language
Recording audio
Subtitle
English
Language 1
English
Select 'Language 1' or 'Language 2' with P- B or P+ A and
confirm with OK .
Menu
English
8
To end, press SYSTEM-MENU .
35
Installing your DVD recorder
Setting the time and date
If the display shows an incorrect time or '--:--', the time and date must be reset manually.
If a TV channel which transmits TXT/PDC (teletext/PDC) is stored under programme number
'P01', the time and date will automatically be taken from the TXT/PDC information.
Warning!
If data from the GUIDE Plus+® system is already available, the date/time will be controlled by the
GUIDE Plus+® system. 'Off' will then appear in line 'Clock preset'.
1
Press SYSTEM-MENU on the remote control. The menu bar
appears.
2
3
4
Select ' ' symbol with D or C .
A
Select 'Installation' using P- B or P+ A and confirm with C .
Select 'Time/Date' using P- B or P+ A and confirm with C .
5
6
7
8
Check if the time in 'Time' is correct. If required, change the time
with the number buttons 0..9 on your remote control.
Installation
Time/Date
Time
Year
20:00
2003
01
Check 'Year', 'Month' and 'Date' in the same way. To move between
the fields, use P- B or P+ A .
Month
Date
01
Clock preset
01
Check the displayed settings and confirm with OK .
'Stored' will appear briefly on the screen.
To exit press
SYSTEM MENU
To end, press SYSTEM-MENU .
36
Installing your DVD recorder
EThe GUIDE Plus+® System
General information
Your DVD Recorder is equipped with the GUIDE Plus+® System. The GUIDE Plus+® System
offers a free interactive electronic programme guide that lists all the TV programmes available in
your area. You can also use the GUIDE Plus+® System to program your DVD recorder to
record your favourite shows.
Press GUIDE/TV to see a summary of all the TV programmes currently being shown on the
various TV channels. For the summary, you can either display all shows for a particular start time
or sorted according to category.
For the GUIDE Plus+® System to operate correctly, it is necessary for the DVD recorder to
collect the necessary data. The DVD recorder may take up to 24 hours to do this.
Please note the following:
•) All the TV channels must already have been installed.
•) The TV channel that transmits the GUIDE Plus+® system information must be installed.
Country/City (Language)
Deutschland
TV;channel
Eurosport
Österreich
Eurosport
Schweiz (Deutsch)
United Kingdom
France
Eurosport
ITV
Canal+
España
Tele 5
Nederland
Eurosport
Eindhoven
Rotterdam
Amsterdam
Belgique (Français)
België (Nederlands)
Music Factory (TMF)
Music Factory (TMF)
Music Factory (TMF)
Canal+
Music Factory (TMF)
•)The time and date must have been set.
•)The country and the local post code must have been set in the GUIDE Plus+® system.
•)The aerial/cable network must be connected; it must be possible to receive TV channels.
•)The DVD recorder must be connected to the mains
•)The DVD recorder must be switched to standby with the STANDBY m button.
•) If you have connected an external receiver (satellite receiver, set-top box, cable TV box,...), it
must be switched on
37
The GUIDE Plus+® System
Setting up the GUIDE Plus+® System
Below we'll tell you how to set up the GUIDE Plus+® System to suit your own particular needs
and how to install the external receiver (satellite receiver, .....) if you have one.
If the GUIDE Plus+® system has not been installed yet, the 'Setup' screen will appear and you
can start with the installation right now.
1
2
Switch on the TV set. If required, select the programme number for
the DVD recorder.
Press the GUIDE/TV button on the remote control.
The 'Grid' screen will appear.
aA 'Setup screen' will appear
b The GUIDE Plus+® system was not completely installed or the installation
was interrupted (local post code was not entered). Select one of the
settings described in the next chapter and follow the instructions on the
screen.
Problem
3
4
Press P+ A . Select the setting 'Setup' with C . This setting is
located on the second page.
Home
Select one of the following options using P- B or P+ A and confirm
with OK .
Setup your system to receive GUIDE Plus+ data.
Schedule Info
Editor
Setup
'Setup' Installation of the GUIDE Plus+® system.
Continue reading in the next chapter.
Setup
View Demo
'View Demo' At this point you will be introduced to the functions of the GUIDE Plus+® system.
This will be done using stored demo data.
If you start the demo, programmed recordings can be deleted.
By pressing OK during the presentation, you can proceed directly to the installation
of the GUIDE Plus+® system. Read the next section.
Setup
Home
'Setup'
Press Aor Bto select. Then press OK to confirm.
Setup
Choose item to set up :
Language
Country
Postal code
External receiver 1
Check the data displayed on the screen. If necessary, you can change these. To do so, select the
corresponding line with P- B or P+ A .
English
United Kingdom
XXXXX
None
External receiver 2
External receiver 3
None
None
'Language'
Here you can change the language for the on-screen menu.
1
2
Press OK .
Select the desired language using P- B or P+ A and confirm with
OK .
3
Press OK to return to the 'Setup' screen.
38
The GUIDE Plus+® System
'Country'
Select the country you currently live from the list. The DVD recorder needs this information to
load the right channel list.
1
Press OK .
a'Others' appears on the screen in the countrysetting
b The country will be taken from the TV set during the EasyLink download.
The country from the TV will be not supported from the GUIDE Plus+®
system.
Problem
Select another country.
2
3
Select the country you live in using P- B or P+ A and confirm with
OK .
Press OK to return to the 'Setup' screen.
'Postal code'
In order to adjust the GUIDE Plus+® system correctly, it is necessary to know your current
location with the TV channels available. Using the local post code and the country, the DVD
recorder can automatically make the settings.
1
2
Press OK .
Choose the entry position using C , D . Select the local post code
of your location using P+ A , P- B , or the number buttons 0..9 .
Depending on the country you select, you can also enter letters using
P- B or P+ A .
aI cannot enter a local post code
b You have selected a country in which none of the channels transmits
GUIDE Plus+® data yet.
Problem
3
4
Confirm the local post code with OK .
Press OK to return to the 'Setup' screen.
'External receiver 1'
How you install the external receiver you will read in the next chapter.
39
The GUIDE Plus+® System
Setup
Home
Installation of the 'External receiver 1'
Press Aor Bto select. Then press OK to confirm.
Setup
Choose item to set up :
Language
Country
Postal code
External receiver 1
If you have connected an external receiver (satellite receiver, set-top box, cable TV box), you
must also install it in the GUIDE Plus+® system. TV programmes (TV channels) that you can only
watch via the receiver can also be displayed in the GUIDE Plus+® system and be programmed for
recording.
English
United Kingdom
XXXXX
None
External receiver 2
External receiver 3
None
None
You can connect up to three external receivers to the DVD-Recorder.
1
Select with P- B or P+ A in the 'Setup'screen the line 'External
receiver 1' and confirm with OK .
2
3
Read the information on the screen and confirm with OK .
Select the type of the external receiver. This setting serves to
preselect the type used.
Which types can I choose?
This selection depends on the country and the GUIDE Plus+® system
provider. Therefore, some types may have no function.
'Cable': Cable receiver, cable box.
'Satellite': Analogue or digital satellite receiver.
'Terrestrial': Digital terrestrial decoder box.
'None': No external device connected.
Tip
4
5
Confirm with OK .
If you selected 'None', there is nothing further you need to do here.
Read on in the section entitled 'Continue set-up'.
Otherwise, you should continue here.
Select your provider from the list. If you do not have a provider,
select 'No provider'
6
7
Confirm with OK .
Select the brand of your external receiver from the list. If, additionally
your provider is printed on your receiver (e.g. Sky,...), you must
choose the provider as brand. Depending on the type and provider
you selected, a limited selection will appear.
Browse through the pages of the list using O , N .
aMybrand is not included in the list
b Select 'Satellite' and as provider 'No provider'.
You will see a list of all stored brands.
b If you do not find your brand, please proceed as follows:
1
2
Select 'None'. You will find this setting at the end of the list.
Please note the type and manufacturer of your external receiver and call
the customer support service in your country. You will find the
telephone number on the back of this instruction manual.
3
The control data of the external receivers are automatically updated
(completed) via the GUIDE Plus+® system. This is done through the
aerial, the cable, or the external receiver. You do not need to bring the
device to a service centre.
Problem
8
Press OK .
40
The GUIDE Plus+® System
9
Select the input socket of the DVD recorder to which the receiver is
connected.
aMyexternal receiver is connected onlyvia aerial cable
1
Press O to move to the next page.
Confirm 'Antenna (RF lead)' using OK .
2
Enter the channel number under which the external receiver is stored in
the DVD recorder. (e.g.: channel number 'P 04'). Use the number
buttons 0..9 , or P- B , P+ A , D , C .
If the external receiver is not allocated to a channel number, you must
search and store it in the DVD recorder as if it were a new TV channel.
Read section 'Search TV channels manually'. Please make sure that the
receiver remains switched on during search and, if necessary, switch it on
to a 'test signal'.
Problem
0
Confirm with OK .
Connecting G;LINK transmitter
The external receiver (satellite receiver, set-top box, cable TV box) is controlled via the DVD
recorder with the G-LINK cable (supplied). This means you can record TV shows that are
received only through the external receiver.
Connection of the G-LINK cable enables the GUIDE Plus+® system to show the correct guide
listing.
1
2
Connect the G-LINK cable to the G-LINK socket at the back of the
DVD recorder.
Position the G-LINK transmitter in front of the external receiver so
that the control signal (IR signal) can be transmitted and received by
the receiver unhindered.
How do I find the right position?
If the position of the remote (IR) receiver is indicated on your external
receiver (IR, remote sensor, or such like), place the transmitter about 1 cm in
front of it.
If the position is not indicated, proceed as follows:
1
2
3
Switch off the external receiver.
Point the remote control at the front of the external receiver.
Move the remote control slowly along the front while repeatedly
pressing the on/off button.
4
5
When the external receiver switches on or off, you've found the
receiver.
Attach the G-LINK transmitter about one (1) cm in front of it.
Tip
3
Switch the receiver on and select programme number 02 on the
receiver or using its remote control.
41
The GUIDE Plus+® System
aMyexternal receiver does not displaythe programme number
During installation, the external receiver will be switched to a different
programme number. If the receiver does not display the programme
number, you must check the 'Video window' (left top corner in the GUIDE
Plus+® system) to see whether switching has taken place. The connection
socket of the receiver will be automatically selected.
1
Please check the TV show in the 'Video window' in the left top corner
of the screen.
Problem
2
Check whether the picture changes during the next step ( OK ).
4
5
Read the information on the screen carefully.
Confirm with OK .
The DVD recorder will now attempt to use the G-Link connection on
the external receiver to select a different programme number (e.g.09).
This programme number depends on your external receiver.
Has the external receiver been switched to the programme number
displayed on the screen?
If this is the case, select 'YES'.
If no switching has taken place, select 'NO'.
aMyexternal receiver has not switched to the other programme
number.
1
2
3
4
5
Check that the external receiver is connected and switched on.
Check the connection and position of the G-LINK transmitter.
For another attempt with a new code of the chosen brand, select 'NO'.
Confirm with OK on the remote control.
If the receiver has not switched yet, select 'NO' again and confirm with
OK . It may take several attempts for a receiver brand.
If you return to the setup screen after confirming 'NO', your receiver
may not have been installed. Check the connections again.
If all connections are o.k., please note the type and manufacturer of your
external receiver and call the customer support service in your country.
You will find the telephone number on the back of this instruction
manual.
6
The control data of the external receivers are automatically updated
(completed) via the GUIDE Plus+® system. This is done through the
aerial, the cable, or the external receiver. You do not need to bring the
device to a service centre.
Problem
Problem
6
7
Your external receiver has now been installed.
Press OK to return to the setup overview.
aI want to install additional external receivers
When installing additional external receivers, please observe the following:
The external receiver which is controlled by the G-LINK transmitter must
be below the other additional receivers. The IR(infrared) remote control
signal is reflected diagonally upwards and can therefore be used to control
additional external receivers which are on top.
42
The GUIDE Plus+® System
Continue set;up
Setup
Home
1
Check the settings shown on the screen.
If the settings are not correct, choose the line in which you want to
change the settings and confirm with OK .
Press Aor Bto select. Then press OK to confirm.
Setup
Choose item to set up :
Language
Country
Postal code
External receiver 1
English
United Kingdom
XXXXX
2
3
Press the green function button to leave the screen.
None
If you want to view a demonstration of the GUIDE Plus+® system
select 'View Demo' with P- B and confirm with OK .
If you start the demo, programmed recordings can be deleted.
If you do not want to see a precentation of the GUIDE Plus+® system,
end using GUIDE/TV .
External receiver 2
External receiver 3
None
None
4
This completes the set-up process for the GUIDE Plus+® system.
Leave the DVD recorder switched off with the STANDBY m button (preferrably during the
night) to load the GUIDE Plus+® data.
The information will be available in the next 24 hours.
What must I payattention to when installing an external receiver
for the first time?
•) The receiver must be switched on.
•) If you can switch between 'TV' and 'Radio' on the receiver, select 'TV'.
•) Select the TV channel that transmits the GUIDE Plus+® data on the
receiver. You will find the corresponding TV channel for your country in the
table in section 'General Information' in chapter 'The GUIDE Plus+ System'.
•) On the DVD recorder, select the programme number of the input socket
to which the external receiver is connected:
'EXT2' Scart socket at the back of the DVD recorder EXT 2 AUX-I/O
'CAM1' S-Video/Video front sockets S-VIDEO / VIDEO
'EXT1' Scart socket at the back of the DVD recorder EXT 1 TO TV-I/O
•) If the external receiver is only connected to the aerial socket, you must
select the programme number on the DVD recorder under which the
external receiver is stored.
•) The DVD recorder must be switched on.
•) If GUIDE Plus+® data were loaded, switch the DVD-Recorder off with the
STANDBY m button for approx.10 minutes. During this time, the data will
be stored in a memory to prevent them from being erased in case of
malfunction (power failure).
You must observe this information only when installing the receiver for the
first time. At this point, there is no GUIDE Plus+® data available yet in order
to automatically detect the TV channel that delivers the GUIDE Plus+® data.
Tip
43
The GUIDE Plus+® System
Using the GUIDE Plus+ ® System
General
The GUIDE Plus+® System provides you with a free on-screen listing for all the TV channels in
your location. You can also use it to control a connected external receiver (satellite receiver, set
top box, cable box).
The information of the GUIDE Plus+® System is divided in six screen components:
•) Function buttons (colour panels) along the top of the screen. These correspond to the colour
buttons of the remote control
•) The video window
•) Programme information or instructions for use
•) A line for the selection of available GUIDE Plus+® menus
•) The channel guide with the current listings
•) Advertising information or instructions on the GUIDE Plus+® system
Calling up the GUIDE Plus+ ® System:
Press GUIDE/TV on the remote control.
Closing the GUIDE Plus+ ® System:
•) Select a programme and press the OK button to leave the GUIDE Plus+® System and view
the programme you selected.
•) Press GUIDE/TV on the remote control to leave the GUIDE Plus+® System and view the
programme in the video window.
Using the buttons on the front of the DVD recorder
Calling up the GUIDE Plus+® System: GUIDE button.
Closing the GUIDE Plus+® System: GUIDE button.
Confirm the function: G button.
Red function button: RECORD button.
Cursor buttons: UP , DOWN , LEFT , RIGHT .
®
Navigating the GUIDE Plus+ System
Press GUIDE/TV to view the main menu. Press P+ A to select the menu line. You can select
one of the following functions with D or C . Press at the desired function the P- B button
for confirmation.
'Grid': Standard GUIDE Plus+® system screen (programme guide)
'Search' TV shows sorted by category (movies, sport, etc.)
'Schedule': Scheduled (pre-programmed) recordings
'Info': Additional special functions in the GUIDE Plus+® system.
'Editor': Display/Change the channel settings for the 'Grid' screen
'Setup': For changing the basic settings. Read further information in the chapter 'Set up the
GUIDE Plus+® System'.
44
The GUIDE Plus+® System
Function buttons (colour buttons)
If GUIDE Plus+® information has been loaded, function buttons (colour fields) at the top of the
screen indicate that you can perform various actions in the GUIDE Plus+® screen. (Red ( ZOOM ),
Green ( ANGLE ), Yellow ( SUBTITLE ), Blue ( AUDIO ) whose function depends on the
respective menu. Always check the function (description) in the corresponding colour field before
pressing a button.
If no colour buttons are displayed, pressing them will have no effect.
INFO button
An t button is also available. If additional information is available (symbol i on the screen), you can
use this button to retrieve the information.
The 'Grid' screen
This list appears when you press the GUIDE/TV button. You can view the current listing for all
the TV channels from today to the same day next week.
ATTENTION!
If data from the GUIDE Plus+® system is already available after the initial installation, check the
allocation of programme numbers to the channels in the 'Editor' screen.
Read therefore the section 'The 'Editor' screen'.
If the TV-channel that transmits the GUIDE Plus+® data was allocated to the wrong programme
number, no further GUIDE Plus+® data can be loaded.
1
Press GUIDE/TV . The 'Grid' screen will appear.
aThe 'Grid' screen appears but is empty
b Either the aerial is not connected or GUIDE Plus+® data is not yet
available. The DVD recorder needs some time to collect this data. Leave it
switched off during this process ( STANDBY m button). Do not disconnect
the DVD recorder from the mains!
b If you have connected an external receiver (satellite receiver, set-top box,
cable TV box,...), it must be switched on.
aI do not see all available TV channels
b Please check your correct channel line up in the 'Editor' screen.
Read therefore the section The 'Editor' screen.
Problem
2
3
Select the TV channel you require with P+ A or P- B . You can
use the number buttons 0..9 to select a TV channel directly.
You can use the O and N buttons to scroll a page at a time.
Choosing a TV channel from a listing
1
2
3
4
Press the yellow function button.
An overview of all TV channels appears.
Select the TV channel you want using C , D , P- B , P+ A .
Confirm with OK .
Tip
Use the D or C button to select the show you want. You can hold
down D or C to browse faster through the start times.
If you hold the button N or O pressed, you can switch forward
or back one day.
45
The GUIDE Plus+® System
4
In the top left of the screen you will see a video picture of the
current show of the selected TV channel.
Unlocking / Locking the picture of the TV channel in the top left
corner
Normally the video picture here is locked to the TV channel which you select
before you call up the GUIDE Plus+® system.
If you prefer to view the current show of the selected TV channel you must
unlock this video picture
Press D to select the channel logo.
You can toggle between the two settings using the red function button.
'Unlock' :You will see the video picture of the TV channel you have just
selected.
Tip
'Lock' :You will always see the video picture of the TV channel that was locked.
5
Press OK to confirm the TV channel. The guide will disappear and
you can now view the current TV show of the TV channel you have
selected.
During a recording in progress you con not change the TV channel.
How do I cancel?
Press GUIDE/TV instead of OK . The guide will disappear and you will be
able to view the show you selected before you called up the GUIDE Plus+®
System.
I want to call the additional information/advertisement on the left
hand side of the screen
Press D in the line of the TV channel repeatedly, until the additional
information/advertisement on the left hand side of the screen is highlighted.
You can toggle between the two sets of information using P- B , P+ A .
You can exit these areas with C or with the blue function button.
Tip
Function buttons (colour buttons ) in the 'Grid' screen
You can use the colour buttons on the remote control to select the following:
'Watch' (green button):
The highlighted TV show is stored as a reminder using the start time and appears in the
'Schedule' screen.
When the start time is reached, a message appears on the screen. You can store up to three
such TV shows.
'Record' (red button):
The highlighted show will be programmed for automatic recording. It appears in the 'Schedule'
screen in a different colour than the 'Watch' recording. You can store up to six TV shows for
recording.
'Home' (blue button):
Return to the current time in the listing ('Grid' screen).
46
The GUIDE Plus+® System
Home
The 'Search' screen
Search displays programme listings by categories of
interest. Press Bto use. Press Dfor Grid. Press Cfor
Schedule
Search
Schedule Info
Movies
All
Editor
Sport
This menu lets you access show listings organised by category. This is an even easier way of
searching the show you want to watch.
Make your selection from a general category (Movies, Sport, Children's, Series, etc.) and a
detailed category (Adventure, Comedy, Drama, etc.)
Action
Animation
Comedy
Drama
Romance
Sci Fi
Thriller
Colours of the categories:,
Purple-Movies
Green-Sport,
Blue-Children's,
Teal-Others,
The Sort service gives you show listings for the next 7 days.
1
Select the category with D , C .
Confirm with P- B . Select the minor category with P- B , D ,
C .
2
3
Confirm with OK
Use the P- B , P+ A , D , C buttons to scroll through the shows.
a'No Program was found' appears on the screen
There is no TV show today that matches the selected category.
b Select a different day with C , D .
Problem
b Press P+ A to return to the 'Search' screen.
Function buttons (colour buttons ) in the 'Search' screen
If you have highlighted a show you can use the coloured buttons to perform the following
actions:
'Watch' (green button):
The highlighted TV show is stored as a reminder using the start time and appears in the
'Schedule' screen.
When the start time is reached, a message appears on the screen. You can store up to three
such TV shows.
'Record' (red button):
The highlighted show will be programmed for recording. It appears in 'Schedule' in a different
colour than the 'Watch' recording.
'Home' (blue button):
Return to the current time in the listing ('Grid' screen).
47
The GUIDE Plus+® System
Quality
Frequency VPS/PDC Home
The 'Schedule' screen
Recording quality M2, Single recording
This menu displays the shows that are set to record or as a reminder to watch them. You can
clear recordings or make changes using the function buttons. Moreover, you can manually
program recordings.
Grid
Watch/Record
21-Oct 20:00 21:30 BBC1 M2
21-Oct Matrix M2
Search
Schedule Info
Qual. Freq. Timing
Once +0
Once
0
The following information is also displayed for each scheduled recording:
'21-Oct': Day and month of the recording
'20:00': Start time
'21:30': Stop time
'Matrix': Title of the show (if it is transmitted)
'BBC1': TV channel
'Qual.': Recording quality
'Freq.': Frequency ('Once'..once/'M-F'..daily (Monday to Friday)/'Mon'..weekly (every week on
the same day, e.g. Monday))
'Timing': In case an extended switch-off time has been entered or 'VPS/PDC' (V-P) is switched
on.
Function buttons (colour buttons ) in the 'Schedule' screen
You can select between programming with the VIDEO Plus+® system (red button) or manual
programming (green button).
If you selected an already programmed TV show, you can make changes using the colour buttons
of the remote control.
The function of the colour buttons will change depending on the tile you select. Always check
the function (description) in the corresponding colour field before pressing a button.
1
2
Press P- B .
Select the corresponding recording with P- B , P+ A .
Select the corresponding tile with D , C .
left tile
red button: clear the recording
green button: change the data
center tile
yellow button: change the TV channel
right tile
red button: recording quality
green button: repeat
yellow button: extend switch-off time, switch VPS/PDC on/off
Tip
48
The GUIDE Plus+® System
The 'Info' screen
This screen can be divided in subcategories. These depend on the information provided by the
GUIDE Plus+® system. If there are no categories available, no data has been provided yet. Try
visiting this page later.
1
Press P- B .
Select the corresponding subcategorywith P- B , P+ A .
2
3
4
Select from the displayed data with P- B or P+ A .
Confirm using OK to receive more information.
Return to the 'Info' screen by pressing the red function button
('Info').
Home
The 'Editor' screen
Editor displays your TV channel settings. You may
switch channel On or Off (grey), select their Source
and their programme number. Press Down to use.
Press Left for Info. Press Right for Setup.
Search
Name
BBC1
BBC2
ITV
Schedule Info
On/Off Source Programme N.
Editor
Here you can allocate the programme numbers to the corresponding TV channels and switch
them on/off for the programme listings ('Grid' screen). Moreover, you can define the use of the
TV channels on the external receiver.
On TV
On TV
On TV
On TV
P 001
P 002
P 003
P 004
CH4
1
2
Press P- B .
Select the TV channel you want to change using P- B , P+ A . Use
the D and C buttons to switch between tiles.
left tile
This tile contains the TV channels with their short descriptions and indicates whether the TV
channel is displayed in the programme listing ('Grid' screen) or not.
You can switch on/off a TV channel for the 'Grid' screen using the red function buttonn
right tile
This tile contains the TV channel properties and the programme numbers. You can modify
channel allocation or assign an external receiver. In order to assign a receiver, it must be already
installed in the GUIDE Plus+® system.
To change allocations, proceed as follows:
1
2
3
Select the TV channel you want to change using P- B , P+ A .
Press the green function button.
Enter the programme number of the TV channel using the number
buttons 0..9 . You can only enter programme numbers of TV
channels that have already been installed.
49
The GUIDE Plus+® System
Entering the TV;channel of an external receiver
1
Select the TV channel you want to watch only through the external
receiver using P- B , P+ A .
2
Choose the corresponding source using the red function button.
This function button is only available when at least one external receiver
has been installed. Read section 'Setting up the GUIDE Plus+® system' on
how to install an external receiver.
3
Press the green function button. Enter the programme number of the TV
channel which you would also enter for this TV channel on the external
receiver.
Tip
Please observe that in the case of modified TV channels, the transfer of GUIDE Plus+® channel
data may take up to 24 hours.
Home
The 'Setup' screen
Setup your system to receive GUIDE Plus+ data.
Here you can make or change the basic settings such as language, country, external receiver.
Moreover, you can watch an automatic demonstration of the GUIDE Plus+® system.
Schedule Info
Editor
Setup
Setup
View Demo
'Setup'
All the settings you have already made are displayed here. Select the desired line using P- B or
P+ A and confirm with OK . For more information on the settings, read section 'Setting up
the GUIDE Plus+® system' in chapter 'The GUIDE Plus+® system'.
'View Demo'
Here you can view a demonstration of the different functions of the GUIDE Plus+® system.
Start the automatic presentation with OK .
If you start the demonstartion, programmed recordings can be deleted.
If you cancel the presentation by pressing OK , you will go directly to the setup menu.
50
The GUIDE Plus+® System
FOn;screen information
You can check or change many of the functions and settings of your DVD recorder via the
system menu bar. The menu bar cannot be displayed during recording.
Symbols in the menu bar
Press SYSTEM-MENU to open and close the menu bar (main menu). Use D and C to select
the relevant function. Use P- B to confirm the function and go either to another menu or
execute the function directly.
Some functions may not be available, depending on the disc inserted.
Menu bar 1
User preferences
A
Title/track
B
Chapter/index
C
Audio language
D
Subtitle language
E
Camera angle
F
Zoom
G
Menu bar 2
While menu bar 1 is being displayed you can go to menu bar 2 by pressing C again.
Sound
H
Frame advance
I
Slow motion
J
Fast forward
K
Search bytime
L
51
On-screen information
Field for temporarymessages
The top left corner of the menu line contains a field for temporary messages relating to the
various operating modes. This information appears briefly on the screen when certain disc
functions have been activated:
Shuffle
/
Scan
6
Repeat entire disc
5
Repeat title
3
Repeat track
4
Repeat chapter
2
Repeat from A to the end
0
Repeat from A to B
1
Camera angle
7
Child lock enabled
l
Resume playback
8
Illegal action
9
Status field
The status field shows the current operating mode (status) of the DVD recorder and the type of
disc inserted. This display can be disabled.
Disc type symbols
DVD+RW
M
DVD+R
W
DVD;Video
N
Video;CD
O
No disc
P
Error
Q
52
On-screen information
Operating mode symbols
Recording
R
Stop
S
Playback
T
Playback;Pause
U
Record;Pause
V
Search forwards (8x speed)
X
Search backwards (8x speed)
Y
Slow motion
Z
Tuner information box
This field is located in the bottom left-hand corner of the screen. The aerial signal, the TV
channel and the TV channel name for the selected programme are displayed.
Current channel/selected input socket
a
No signal
b
The TV channel is not available/the additional device is not connected or
it is switched off
Copy;protected signal
c
Timer information box
This box appears above the tuner information box. When a timer recording is set, it shows the
timer icon and the start time or date of the first programme to be recorded.
If no timer recording is scheduled, the current time is displayed.
This box disappears during playback of a disc or after a recording starts. However, you can
access it during an OTR recording by pressing SYSTEM-MENU .
Timer starts on the day/time shown
f
OTR recording runs until the stop time displayed
g
Current time
No timer event programmed
h
53
On-screen information
GPlayback
General notes on playback
With this DVD recorder you can play back the following systems:
•) DVD Video
•) (Super)Video CD Disc
•) DVD+RW Disc
•) DVD+R Disc
•) DVD-RW (video mode, finalised)
•) DVD-R
•) CD-R
•) CD-RW
•) Audio CD
•) MP3 CD
You can operate the video recorder using the remote control or the buttons on the front of the
DVD recorder.
aThe displaywill read ' PIN'
b The child lock has been activated for the inserted disc. Read the sections
on 'Child lock' and 'Releasing a disc' in the chapter on 'Access control
(child lock).
aThe menu on the screen is showing an 'X'
b Some DVD discs can be manufactured so that certain steps are required
before the disc can be played, or so that only limited operation is possible
during playback. When an 'X' appears on the screen the selected feature is
not possible.
aThe screen is showing regional code information
b Since DVD films are not normally released in all parts of the world at the
same time, all DVD players have a specific regional code. Discs can be given
a regional code. If the regional codes differ between the player and the
disc, playback is not possible.
b The regional code is shown on the label on the back of the machine.
b The regional code does not apply to recordable DVD discs.
Problem
Inserting a disc
1
2
Press the OPEN/CLOSE J button on the front. The disc tray will
open. While the disc tray is opening, 'OPENING' and then 'TRAY OPEN'
when the tray is fully open.
OPENING
P01
Carefully place the disc in the tray with the label facing up and press
PLAY G or OPEN/CLOSE J . 'CLOSING' and then 'READING' will
appear in the display. The information on the disc will be read.
How do I insert a double;sided DVD?
Double-sided discs do not have labelling over the whole surface. The labelling
for each side is in the centre of the disc. To play a side its label must be
facing up.
?
54
Playback
Opening/closing the trayusing the remote control
You can open and close the disc tray using the remote control.
Press and hold the STOP h button on the remote control until the dialog
box shows 'OPENING' or 'CLOSING'.
Tip
3
Playback starts automatically.
A menu may appear when a DVD is played back. If the titles and chapters are numbered, press a
number button on the remote control. You can also use the D , C , P+ A , P- B buttons
or number buttons 0..9 to select a menu item and confirm with OK .
You can also access the menu using DISC-MENU on the remote control.
For further information see 'Playing a DVD video disc'.
When a DVD+RW is played back the index overview appears. Using P- B , P+ A , N ,
O select the title you want to play back.
Confirm with OK .
For further information see 'Playing back a DVD+RW/+R Disc'.
If playback does not start automatically, press PLAY G .
For further information see 'Playing an audio CD'.
If the 'h' symbol appears in the display, start playback by pressing PLAY G .
If a menu appears on the screen, use the remote control buttons indicated on the screen to select
the menu option you want (PREV= N , NEXT= O ) or with the number buttons 0..9 .
For further information see ' Playing a (Super) Video CD'.
Playing a DVD video disc
1
If playback does not start automatically, press PLAY G .
This will appear on the display:
title, chapter, elapsed time.
C01
2:04
2
3
To stop playback, press STOP h on the remote control or h on
the DVD recorder.
To eject the disc, press OPEN/CLOSE J on the front of the DVD
recorder.
55
Playback
Playing a DVD+RW/ +R disc
1
2
If the disc is write-protected or a finalised DVD+R disc, playback
starts automatically.
If playback does not start automatically, use the P- B or
P+ A button to select the title you want to play on the index
screen.
C01 ANNA
P01
You can also use the N or O button on the front.
3
Press the PLAY G button.
This will appear on the display:
title number, recording quality.
aI can see the message 'EMPTYDISC'
b The disc does not contain any recordings.
Problem
4
5
To stop playback, press STOP h on the remote control or h on
the DVD recorder.
To eject the disc, press OPEN/CLOSE J on the front of the DVD
recorder.
What should I note when playing back different recording types
(qualities)?
The correct recording quality 'M1, M2, M2x, M3, M4, M6',M8' will
automatically be selected during playback.
For more information see the section on 'Selecting the recording type
(quality)' in the chapter on 'Manual recording'.
?
Playing an audio CD
You can also use the DVD recorder to play audio CDs
1
Insert an audio CD. Playback starts automatically.
Audio CD display'
If the TV is on, the audio CD screen appears automatically.
During playback, the current track number and its elapsed playing time will
show on the TV screen and on the recorder display.
Tip
2
Stop playback using STOP h . The number of tracks and the total
time are displayed.
56
Playback
Playing an MP3 CD
MP3 (MPEG1 Audio Layer-3) files are highly compressed music files. Using this technology the
data volume can be compressed by a factor of 10. This means it is possible to record 10 hours
of music in CD quality on a single CD-ROM.
When creating MP3 CDs please note the following:
File system: ISO9660
Directory structure: maximum of 8 levels
Formats: *.mp3
Filenames: maximum of 12 characters (8+3)
Maximum of 32 albums, 999 titles
Supported sampling frequencies: 32, 44.1, 48 (kHz). Music with sampling frequencies other than
these will be skipped.
Supported bit rates: 32, 64, 96, 128, 192, 256 (kbit/s)
ID3 Tag: Version 1, 1.1. In later versions the directory name is displayed as the album and the
filename as the title.
Important notes for playback:
Only the first session of a multi-session CD will play back.
1
2
Insert an MP3 CD. Playback starts automatically.
MP3 CD display
If the TV is on, the MP3 CD screen appears automatically.
During playback, the current track number and its elapsed playing time will
show on the TV screen and on the recorder display.
During stopped playback ( STOP h button) the numbers of the albums will
show on the TV screen and on the display.
Further information on the album, track and artist will also be displayed if
included in the ID tag.
Tip
Stop playback using STOP h . The number of albums is displayed in
the display.
Additional playback features
Using N or O select the next or previous title.
You can also use the T/C button to select titles and albums.
1
Press the T/C button and use the C or D button to select the 'T'
symbol for title or 'C' for chapter.
2
Use the P- B or P+ A buttons or the number buttons 0..9 on the
remote control to select the number of the title/chapter.
Tip
You can also use the repeat functions ( PLAY MODE button).
57
Playback
Playing a (Super) Video CD
(Super) Video CDs may be equipped with PBC (Play Back Control). This means that special
playback functions (menus) can be directly selected. The video CD must be PBC compatible (see
CD case).
'PBC' is active in the default settings.
1
2
Insert a (Super) Video CD.
If the 'h' symbol appears in the display, start playback by pressing
PLAY G .
If a menu appears on the screen, use the remote control buttons
indicated on the screen to select the menu option you want
(PREV= N , NEXT= O ) or with the number buttons 0..9 .
If a PBC menu consists of a list of titles, you can select a title directly.
3
4
Use RETURN to go back to the previous menu
Stop playback using STOP h .
58
Playback
HAdditonal playback features
Changing to another title/chapter
If there is more than one title or chapter on a disc you can change to another title or chapter
as follows. However if there are several chapters within a title, these will be selected. The title
can then still be selected via the menu bar.
1
During playback, press O to go to the next title/chapter. Press
N to return to the start of the current title/chapter. Press
N twice to return to the start of the previous title/chapter.
Use the T/C (title/chapter) button
1
Press T/C (title/chapter) and then use P+ A or P- B to select the
appropriate title.
Make sure the symbol 'T' (title) is selected in the menu bar.
Use T/C to select chapters within a title. Press T/C and use C to
select the 'C' symbol (chapter).
2
Tip
Now select the appropriate chapter with P+ A or P- B .
Searching a disc
You can search the disc for a recording at 4x, 8x or 32x playback speed. Other speeds can only
be selected via the menu bar (' ').
K
1
2
During playback, press and hold N (reverse) or O (forwards) to
switch to the search feature. You can switch between the playback
speeds using N / O .
To continue playback, press PLAY G twice at your chosen location.
aNo sound
b The sound is switched off in search mode. This is not a fault in your
machine.
Problem
Search feature via menu bar
1
During playback press SYSTEM-MENU on the remote control. The
menu bar will appear at the top of the screen.
2
3
Select the '
' symbol using C or D and confirm with P- B .
K
You can now use the D or C button to select different forward and
backward search speeds.
4
5
If necessary, switch the menu bar off with the SYSTEM-MENU button.
To continue playback, press PLAY G twice.
Tip
59
Additonal playback features
Still picture
1
During playback, press PAUSE 9 to stop playback and display a still
picture.
C01
2:04
Frame advance via menu bar
1
During a still picture press SYSTEM-MENU on the remote control.
The menu bar will appear at the top of the screen.
2
3
Select the '
' symbol using C or D and confirm with P- B .
I
You can now use the D or C button to go forwards or backwards one
frame at a time.
4
If necessary, switch the menu bar off with the SYSTEM-MENU button.
Tip
2
To continue playback, press PLAY G .
Slow motion
1
2
During playback press PAUSE 9 on the remote control. Now hold
down N or O to switch to slow motion.
You can switch between different speeds using N or O .
Slow motion via menu bar
1
During playback press PAUSE 9 and then SYSTEM-MENU on the
remote control. The menu bar will appear at the top of the screen.
2
3
Select the ' ' symbol using C or D and confirm with P- B .
You can now use the D or C button to select different forward and
backward slow motion speeds.
J
4
If necessary, switch the menu bar off with the SYSTEM-MENU button.
Tip
3
To continue playback, press PLAY G twice.
Search bytime
Using this feature you can select where playback should start (select elapsed time).
1
2
During playback press SYSTEM-MENU on the remote control. The
menu bar will appear at the top of the screen.
Select the ' ' symbol using C or D and confirm with P- B .
L
Playback is stopped and a box appears on the screen showing the
elapsed time.
60
Additonal playback features
3
4
Enter the start time with the digit keys 0..9 from where playback
should start.
Confirm with OK .
aThe time entered will flash on the screen
b The selected title is shorter than the time entered. Enter a new time or
cancel the function by pressing SYSTEM-MENU .
Problem
5
Playback starts at the time you entered.
Repeat/Shuffle play
You can mark entire sections or the whole disc for endless playback. Depending on the type of
disc (DVD video, DVD+RW, video CD) you can select a chapter, title or the entire disc.
1
2
Select the desired chapter, title or the entire disc and start playback.
During playback, press PLAY MODE . By pressing PLAY
MODE again you can chose from the following options:
•) '
•) '
•) '
•) '
': repeat chapter (DVD only)
': repeat track/title
': repeat entire disc (Video CD, Audio CD only)
': Shuffle
2
3
5
/
•) Display disappears: no repeat
3
To end the repeat, press the STOP h button.
You can also keep pressing the PLAY MODE button until the
displays disappear.
Repeating a passage (A;B)
You can repeat a particular passage within a title/chapter. You need to indicate the start and end
of the passage.
1
2
During playback press PAUSE 9 at the start point.
You will see a still picture.
Keep pressing PLAY MODE until ' ' appears on the screen.
0
The start point is now saved.
Press PLAY G to start playback.
3
4
When the end point is reached press OK . '
TV screen. Playback now takes place within these points.
' appears on the
1
To end the repeat, press the STOP h button.
You can also keep pressing the PLAY MODE button until the
displays disappear.
61
Additonal playback features
Scan feature
This feature plays back the first 10 seconds of each chapter (DVD) or track (CD).
1
2
During playback, press PLAY MODE . Select '
MODE .
' using PLAY
6
After 10 seconds the DVD recorder switches to the next
chapter/index. To start playback at the relevant chapter/index press
STOP h and then PLAY G .
Camera angle
If a DVD contains scenes that have been shot from different camera angles you can select these
camera angles for playback.
1
2
During playback, press PAUSE 9 . You will see a still picture.
Press SYSTEM-MENU and select the ' ' icon using C .
F
aThe ' ' symbol will be hidden
F
b The selected scene has been shot from only one camera angle. This feature
is therefore not available. For more information please read the cover of
your DVD disc.
Problem
3
4
Select the required camera angle with P- B or P+ A . You can also
directly enter the number with the number buttons 0..9 .
After a short time, playback will resume from the new camera angle.
The ' ' symbol will remain visible until a scene starts for which
F
there is only one camera angle.
Zoom feature
The Zoom feature allows you to enlarge the video image and pan through the enlarged image.
1
During playback, press ZOOM . The DVD recorder switches to
'PAUSE'. You will see a still picture.
2
3
Select the required zoom factor using P- B or P+ A .
When 'press OK to pan' appears on the screen, the zoom process
is complete.
4
Press OK . Using P+ A , P- B , C , D select the part of the
image you wish to view.
5
6
Confirm with OK .
To stop the feature, press PLAY G and then SYSTEM-MENU .
62
Additonal playback features
Select the audio language
Many pre-recorded DVD discs have more than one audio language. The language initially selected
for playback will be the one you selected when you first set up the DVD recorder. However
you can change the audio language of the inserted disc at any time.
You can change the audio language either using the menu of the inserted disc
( DISC-MENU button) or the AUDIO button. The audio languages for DVD playback in the
two menus may be different. Please note that with some DVDs the audio language and/or
subtitle language can be changed only via the DVD menu.
1
2
During playback press AUDIO .
Select the required audio language using P- B or P+ A . You can
also enter the number directly using the number buttons 0..9 .
3
Play continues in the new audio language.
Subtitles
Many pre-recorded DVD discs have more than one subtitle language. The language initially
selected for playback will be the one you selected when you first set up the DVD recorder.
However you can change the subtitle language of the inserted disc at any time.
You can change the subtitle language either using the menu of the inserted disc
( DISC-MENU button) or the SUBTITLE button. The subtitle languages in the menus may
differ.
1
2
During playback press SUBTITLE .
Select the required subtitle language using P- B or P+ A . You can
also enter the number directly using the number buttons 0..9 .
You can switch off subtitles again with 0 or by pressing 'off'.
Playback continues in the new subtitle language.
63
Additonal playback features
IDisc Manager (DM)
General information
The 'Disc Manager' is an integrated database in the DVD recorder that remembers all recordings
made by this DVD recorder. This gives you a complete overview of your entire video collection
at the touch of a button. The Disc Manager gives you quick and easy access to every recording
made with this DVD recorder. The Disc Manager also tells you which film was recorded on
which disc and how many unrecorded minutes remain on the discs.
And: You can go automatically to the beginning of the selected recording and start playback.
How manydiscs can I save in the Disc Manager?
You can store up to 999 discs on this DVD recorder. The maximum number
of titles is more than 9,000. The maximum number of titles per disc is 49.
?
Caution when recording with other DVD recorders
Don't use a disc stored in the Disc Manager for recording on other DVD
recorders. If you use a disc to record on another DVD recorder, then this
disc will no longer be recognised by the Disc Manager. In this case, delete the
disc from the Disc Manager's memory and then add it after it has been
recorded.
Adding 'child;proof discs'
Tip
If you want to add child-proof discs you need to enter the PIN code.
Adding a disc to the Disc Manager
You can only add DVD+RW or DVD+R discs to the Disc Manager since other discs do not hold
any information on the titles or lengths of the recordings. These discs have to be at least once
recorded in the DVD-Recorder. A table of content have to be available.
DVD+R discs can also be finalised. Other discs cannot be added to the Disc Mana
Recordings are saved automatically
On a disc that has been added to the Disc Manager, you can make new
recordings as often as you like using this DVD recorder. The titles of these
recordings will be stored in the Disc Manager automatically.
Tip
1
Insert a DVD+RW/+R disc in the DVD recorder.
64
Disc Manager (DM)
Disc Manager
Find title
C04
Browse discs
Remove a disc
Add current disc
Disc number001
Disc number001
aWhen I insert a disc I see a number on the screen in the title
overview in the top left;hand corner
Next free disc number= 001
b You have inserted a disc that has already been registered by the Disc
Manager.
Problem
To exit press DM
2
3
Press the DISC MANAGER button on the remote control.
Select 'Add current disc' using P+ A or P- B and confirm with
C .
4
Confirm with OK .
The disc number will be added to the Disc Manager. This will appear
on the screen:
5
6
The disc number is then displayed and the disc tray opens
automatically.
The disc is now stored in the Disc Manager under the displayed disc
number.
Please write this number on the disc and on the cover.
Whydo I need to label the discs?
When searching for unrecorded free space or available recordings, you will
asked to insert the appropriate discs (disc numbers).
?
7
To end, press DISC MANAGER .
The DVD recorder will immediately recognise that this disc is saved in the Disc Manager. When
this disc is inserted the disc number will appear in the title overview in the top left-hand corner.
Removing discs from the Disc Manager
Every DVD+RW/+R is stored with a number in the Disc Manager (DM). You can remove this
disc number from the Disc Manager to use the Disc Manager's memory for new discs or to
remove damaged discs from memory.
1
2
Press DISC MANAGER on the remote control.
Select 'Remove a disc' using P+ A or P- B and confirm with C .
3
Select the disc number with P+ A or P- B and confirm with OK .
Disc Manager
Find title
C04
Browse discs
Remove a disc
Add current disc
Disc number001
Disc number001
Disc contents are not deleted.
Next free disc number= 001
The disc is only removed from the Disc Manager's memory. Its contents
remain unchanged.
Tip
To exit press DM
4
To end, press DISC MANAGER .
65
Disc Manager (DM)
Searching for a title in the Disc Manager
This function can be used to quickly and easily find and play back a recording saved in the Disc
Manager.
1
2
Press DISC MANAGER on the remote control.
Select 'Find title' using P- B or P+ A and confirm with C .
3
A list of the titles of all recordings stored in the Disc Manager (DM)
will appear on the TV screen.
Disc Manager
Date Duration
Find title
Title
Charly 1
01/01/03 0:28
What do the displays on the screen mean?
'Title' = Title
'Date' = Date of the recording
'Duration' = Length of the recording
Tip
Page1/1
To select title press OK
4
5
Select the title that you want to play back with P- B or P+ A .
Confirm with C . The DVD recorder will jump to the start of the
selected recording.
aI see the message 'Insert disc number' on myscreen
b The selected recording is located on the Disc Manager disc with the
displayed disc number. Please insert the appropriate disc. After a brief
check, the DVD recorder will jump to the start of the selected recording.
Problem
66
Disc Manager (DM)
Searching discs
You can easily search for the title of a recording stored in the Disc Manager. To do this, the
appropriate disc does not have to be in the DVD recorder.
1
2
3
Press DISC MANAGER on the remote control.
Select 'Browse discs' using P- B or P+ A .
Confirm with C . The screen will show the contents of the last Disc
Manager disc used.
4
Use P+ A or P- B to select a different disc number if necessary
and confirm with C .
Disc Manager
001
Disc number
Browse discs
Title
Date
Duration
Charly 1
01/01/03 0:28
What do the displays on the screen mean?
'Title' = Title
'Date' = Date of the recording
'Duration' = Length of the recording
?
Page1/1
To select title press OK
5
6
Press P+ A or P- B to select the desired title.
Confirm with OK .
aI see the message 'Insert disc number' on myscreen
b The selected recording is located on the Disc Manager disc with the
displayed disc number. Please insert the appropriate disc.
Problem
7
The DVD recorder searches for the start of the appropriate
recording.
67
Disc Manager (DM)
Searching for a blank section
You can search for space for a new recording on the disc (at least 1 minute of blank space), for
example at the end of existing recordings.
This only works with discs which have already been stored in the Disc Manager.
1
2
3
Press DISC MANAGER on the remote control.
Select 'Browse discs' using P+ A or P- B .
Confirm with OK . A list of the recordings on the disc you have
selected will appear on the TV screen.
4
Use P+ A or P- B to select a disc (disc number) on which there is
enough space for the recording.
How can I see how much space is available for the recording?
The space available is designated as 'Empty'. The time is displayed next to the
title 'Empty'. You can use the REC MODE button to change the recording
mode (recording time).
How can I choose the titlel 'Empty' if there were manyrecordings
on the disc?
?
In this case press C and then select with P- B , P+ A the title 'Empty'.
5
6
Select the title 'Empty' with P+ A or P- B .
Disc Manager
001
Disc number
Confirm with OK .
Browse discs
Title
Date
Duration
Charly 1
01/01/03 0:28
aI see the message 'Insert disc number' on the screen.
b The blank space is located on the Disc Manager disc with the displayed disc
number. Please insert the appropriate disc.
Page1/1
To select title press OK
Problem
The DVD recorder rewinds to the beginning of that particular part and automatically switches to
Stop.
68
Disc Manager (DM)
JManual recording
General
Which discs can I use for recording?
With this DVD recorder, you can record on two types of DVD:
DVD+RW
This disc can be written to and then the contents deleted.
DVD+R
This type of disc can only be recorded once.
If you want to play this DVD in a DVD player it must be finalized using the
'Finalise disc' function. It is not possible to make further recordings using
this disc.
If this disc is to be played in a DVD recorder it must not be finalised.
Recordings can be added and deleted. The disc space (playback time) from the
deleted recording cannot be recovered for further recordings
?
Use the 'Manual recording' function to spontaneously start recording (e.g. to record a TV show
already in progress).
In the 'index display' select the title to be overwritten or 'Empty title' with P- B , P+ A .
If you insert recordings between existing recordings, check the lengths of the old and new
recordings. If the new recording is too long the subsequent recording (title/chapter) will be
overwritten.
Insert new recordings at the end of all existing recordings (Safe
Record)
To add a new recording at the end of the last recording on the disc, hold
down the REC/OTR n button until the message 'SAFE REC' appears on the
display.
For DVD+R discs each new recording is always added at the end of all
previous recordings as existing recordings cannot be overwritten.
End of disc is reached
If the end of a disc is reached during recording, recording will stop and the
Recorder will turn itself off automatically.
Tip
Please refer to section 'Recording without automatic switch;off', if you want to manually
start and stop your own recording.
If you want to start a recording manually but have it stopped automatically, read the section
'Recording with automatic switch;off'. (e.g. not to record to the end of the disc)
Read the section 'Automatic recording from a satellite receiver', if you want a recording
to be controlled automatically by a satellite receiver.
Read the section 'Direct record' if you want to record a programme currently being shown.
69
Manual recording
Recording without automatic switch;off
1
2
Switch on the TV set and select the programme number for the DVD
recorder.
Insert a disc on which the recording is to be made. This disc is then
checked for content and system. READING' will appear on the display.
aIndex display
b A DVD+RW disc has been inserted that already contains recordings. Use
the P+ A or P- B button to select the point where the recording is to
start.
aThe message 'EMPTYDISC' appears in the display
b The disc inserted is a blank DVD disc.
aA dialog box appears asking you whether you want to delete the
contents or eject the disc
b The disc inserted is
a
DVD+RW but its contents are not DVD
video-compatible (e.g. a data disc). Recordings on this disc can only be
made if the entire disc is first deleted with the REC/OTR n button.
aThe message 'Title limit' appears on the screen if a recording is to
be made
b A disc may contain a maximum of 48 titles (including blank titles). Delete
titles or change the disc.
Problem
3
4
If necessary, use the MONITOR button on the remote control to
switch to the internal tuner in the DVD recorder.
Use P+ A or P- B to select the programme number (station name)
you want to record. This will appear on the display:
1 FREETITLE P01
Programme numbers of the external inputs:
'EXT1' Scart socket at the back EXT 1 TO TV-I/O
'EXT2' Scart socket at the back EXT 2 AUX-I/O
'CAM1' Front SVHS/audio sockets S-VIDEO / left AUDIO right
'CAM1' Front video/audio sockets A/V S-VIDEO / left AUDIO right
Switching between the S-VIDEO and VIDEO sockets takes place
automatically. If a signal is available at both sockets at the same time,
the signal at the S-VIDEO socket has priority.
Tip
'CAM2' Digital Video (i Link) front socket DV IN
5
To start recording, press REC/OTR n on the remote control or
RECORD on the DVD recorder.
If you want to start the recording at the end of the existing
recordings, hold down the REC/OTR n button until the message
'SAFE REC' appears on the display.
For DVD+R discs each new recording is always added at the end of
all previous recordings as existing recordings cannot be overwritten.
This will, for example, appear in the display:
70
Manual recording
C01 1:16:51 P01
Insert chapter markers
During recording you can mark scenes so you can find them or hide them
later.
During recording, press FSS & at the start point. 'Inserting marker'
appears on the TV screen. In the display, the number of the 'CHAPTER'
increases by one.
For further information on titles and chapters, see the section on 'Changing to
another title/chapter' in 'Playback'.
Tip
6
Use the STOP h button on the remote control or h on the
machine to stop the recording. 'MENU UPDT' will appear on the display.
The DVD recorder is writing the list of contents. Wait until the
message disappears from the display. The recording is then complete.
aThe displaywill read ' DISC ERR'
b Recording could not be completed correctly because of a disc error. Check
the disc and clean it if necessary.
Problem
Making recordings on DVD+R discs compatible
If you want to play back the recording on a DVD player, you need to finalise
the disc in the DVD recorder. You can prepare your DVD for use in a DVD
player using the 'Finalising' feature. See 'Finalising DVD+R discs' in 'Managing
the disc contents'.
Tip
Interrupt recording (Pause)
1
2
During recording press PAUSE 9 , for example to avoid recording
the commercials.
To continue recording, press REC/OTR n .
End recording
To end the recording, press the STOP h button. Wait until 'MENU UPDT'
disappears from the display.
Tip
71
Manual recording
Recording with automatic switch;off (OTR
one;touch;recording)
1
2
Insert a disc.
If necessary, use the MONITOR button on the remote control to
switch to the internal tuner in the DVD recorder.
3
Use P+ A or P- B to select the programme number (channel
name) you want to record.
4
5
Press REC/OTR n on the remote control.
Each time you press REC/OTR n you will add 30 minutes to the
recording time.
How can I cancel the recording time I have just entered?
To delete an entry, press CLEAR while the display shows the recording
time.
How can I check the remaining recording time?
Press SYSTEM-MENU while an OTR is in progress. The time at which the
recording will end will appear on the TV screen in the timer info box.
?
Preventing accidental erasing of discs
To ensure you don't accidentally delete a recording you can protect the entire disc. You can
only ever protect the entire disc. You cannot protect individual recordings.
What happens with DVD+R discs?
As long as these discs are not finalised, they can be protected against
accidental erasure in the same way as DVD+RW discs.
?
1
2
Insert the disc to be protected.
While the index screen is displayed press STOP h on the remote
control. The first title is highlighted.
3
4
Press P+ A . This takes you to the disc info screen.
Press the C button.
Select the 'Protection' line.
Confirm with C .
72
Manual recording
5
6
Select 'Protected' with the P- B button and confirm with OK .
Press D and then DISC-MENU to terminate.
The entire disc is now protected.
If an attempt is made to record on a protected disc, 'DISC LOCK' will
appear on the display and 'Disc locked' will appear on the screen.
If you later decide to record on the disc, follow these steps but select
'Unprotected' at step 5 .
Tip
Lining up recordings within a title
(assemble cut)
On a recorded DVD+RW disc you can add another recording to an existing title. This recording
is added to the title as a 'chapter'. The existing information will be overwritten starting from this
point. Titles will also be overwritten that follow the current title depending on the length of the
new recording. The recording type (Quality) will be taken from the current title.
To play back this recording, press SYSTEM-MENU and use the C button to select the 'C'
(Chapter) symbol. You can also use the T/C key.
For further information, see 'Changing to another title/chapter' in 'Playback'.
What happens with DVD+R discs?
New recordings on 'DVD+R' discs can only be added after existing recordings.
It is not possible to overwrite existing recordings on 'DVD+R' discs.
?
1
In the index display, find the title to which the new recording is to be
added.
2
3
Look at the last minute of the old recording (playback)
Press PAUSE 9 on the remote control at the position where the
new recording is to go. '9' will appear on the screen.
4
5
To monitor the recording you can press MONITOR to switch to the
internal tuner.
Now start recording as usual by pressing REC/OTR n on the
remote control.
The new recording will be inserted.
6
Stop recording with STOP h .
73
Manual recording
Selecting the recording type (Quality)
You can select the picture quality of the recording using the recording quality feature and hence
the maximum recording time per disc.
To check the quality of a recording mode you can make a 'test recording' with the desired
recording mode. Check during playback the quality of this 'test recording'.
During playback, the correct picture quality will automatically be selected.
1
Switch on the TV set. If required, select the programme number for
the DVD recorder.
Select the record mode with the button REC MODE on the remote
control.
Which recording types can I choose?
'M1': High Quality offers the best picture quality and a recording time of 1
hour.
'M2': Standard Play (pre-recorded DVD quality) offers standard picture quality
and a recording time of 2 hours.
'M2x': Standard Play plus (better than S-VHS quality) offers standard picture
quality and a recording time of 2.5 hours.
'M3': Long Play (S-VHS picture quality). Recording time of 3 hours.
'M4': Extended Play (better than VHS picture quality). Recording time of 4
hours.
'M6': Super Long Play (VHS picture quality). Recording time of 6 hours.
'M8': Super Extended Play (VHS picture quality). Recording time of 8 hours.
Can I select the recording type via a menu as well?
1
2
3
4
5
6
Press the SYSTEM-MENU button.
Select ' ' symbol with D or C .
Select 'Record settings' using P- B or P+ A and confirm with C .
In the line 'Record mode' select the recording type with D or C .
Confirm using OK and SYSTEM-MENU .
If you have selected the recording mode 'M3', 'M4', 'M6' or 'M8', you
can select the 'Stndrd' (Standard) or 'Sport' setting (for rapid
movements) in the 'Filter mode' line.
A
Tip
74
Manual recording
Automatic recording from a satellite
receiver (Sat recording)
You can use this function if your own a satellite receiver that can control other devices via a
scart cable and a programming function (timer). For more information, please see the operating
instructions for the satellite receiver.
1
2
3
4
Switch on the TV set. If required, select the programme number for
the DVD recorder.
Press SYSTEM-MENU on the remote control. The menu bar
appears.
Select ' ' symbol with D or C .
A
Select 'Record settings' using P- B or P+ A and confirm with
C .
5
6
Select 'Sat record' using P- B or P+ A .
Select 'EXT2' with D or C .
Switching off 'Sat Recording'
Tip
To switch off the function, select 'Off' using C or D .
7
8
Confirm with OK .
Use a scart cable to connect scart socket EXT 2 AUX-I/O on the
DVD recorder to the corresponding scart socket on the satellite
receiver.
9
0
A
To end, press SYSTEM-MENU .
Insert a disc you want to use for recording.
Programme the satellite receiver with the required information
(programme number of the TV channel, start time, finish time).
If necessary, please see the operating instructions for your satellite
receiver.
B
Switch off the DVD recorder using STANDBY m . 'SAT' also
appears in the display to indicate that the function is active.
The DVD recorder is now ready to record. The start and end of the recording is controlled via
scart cable EXT 2 AUX-I/O .
75
Manual recording
Direct Record
Can you record the right TV channel in seconds when the DVD recorder is switched off? No
problem. If recording is started manually, the switched;off DVD recorder takes the current TV
channel from the TV set via the scart cable.
You will find more information on how to switch 'Direct record' on or off in the next section
'Direct record'.
How does Direct Record work?
The DVD recorder compares the TV channel selected on the TV set with its
stored TV channels via the scart cable. If the same TV channel is found, it
switches the DVD recorder to the corresponding programme number and
starts recording.
Please do not change channel on the TV during the search. This could affect
the tuning of the DVD recorder.
?
1
2
On the TV set, select the programme number you want make the
recording from.
Press REC/OTR n with the DVD recorder switched off.
aThe displaywill read ' WAIT'
b The DVD recorder is comparing its saved TV channels with those of the
TV set. Please do not change the TV channel on the TV set while 'WAIT' is
shown in the display.
a'NOTV' appears in the display
b This TV channel could not be found in the DVD recorder's memory.
Check that all TV channels saved on the TV set are available on the DVD
recorder. If required, save any missing channels. Please read 'Manual TV
channel search' in 'Installing your DVD recorder'.
b Check the connectors at both ends of the scart cable.
b Check your TV's operating instructions to see which scart socket is used
for video signals.
Problem
b If the problem persists, you won't be able to use this feature.
3
Stop recording with STOP h .
76
Manual recording
Switching 'Direct Record' on or off
1
2
Switch on the TV set. If required, select the programme number for
the DVD recorder.
Press SYSTEM-MENU on the remote control. The menu bar
appears.
3
4
Select ' ' symbol with D or C .
A
Select 'Record settings' using P- B or P+ A and confirm with
C .
5
6
Select 'Direct Record' using P- B or P+ A .
Select 'On' (Direct Record on) or 'Off' (Direct Record off) using
D or C .
7
8
9
Confirm with OK .
To end, press SYSTEM-MENU .
Switch off with STANDBY m .
77
Manual recording
KManaging the disc contents
General
Charly 1
00:29:59 • M1
Fri15/02/2003
When a recording is made to disc, the following additional information is also stored at the
beginning of the recording:
•) Name of the recording
If a name has not been assigned to the TV channel, only the programme number and time are
Empty title
01:30:01
stored as the name
•) Length of the recording
•) Record type (Quality)
•) Date of the recording
•) Index picture of the recording
A marker will be set every 5-6 minutes if the 'Auto chapters' function is activated in the
'Record settings' menu. This marker is known as a 'chapter'.
These markers can be changed when the recording has finished.
Can markers be set on a DVD+R disc?
?
Markers can be set on these discs if they have not been finalised.
It is also possible to add 'chapters' later. This means that scenes you do not want to see during
playback, such as commercials, can be hidden or skipped. During playback you can watch your
recording as a continuous sequence without the hidden chapters.
Select from the following chapters:
'Favorite Scene Selection',
to divide the title into chapters or to manage the chapters.
'Editing recording titles (name)',
to change the recording names.
'Playcomplete title' ,
to play the entire title including the hidden chapters.
'Delete recording/title'to delete the relevant title and therefore also the recording.
'Disc settings'to change the general settings of the disc.
78
Managing the disc contents
Favorite Scene Selection
In this menu you can adapt a title to suit your particular needs.
You can insert/delete chapter markers, hide chapters, select a new index, or split up a title.
Press FSS & on the remote control during recording to open this menu.
Insert chapter markers
During recording, you can set or delete chapter markers within a title.
The maximum number of chapters per disc is 124 and 99 per title. If one of these limits is
reached the following message will appear on the screen: 'Chapter limit'. You need to delete
some markers before you can insert new ones or make recordings.
1
2
During playback, press FSS & on the remote control at the
appropriate point. The 'Favorite Scene Selection' menu appears on
the TV screen.
Confirm 'Insert marker' by pressing OK . 'Inserting marker'
appears on the TV screen.
Favorite Scene Selection
Insert marker
Press OK
visible
Current chapter
Delete marker
Delete all markers
New index picture
Divide title
'X' will appear on the screen:
This DVD is write-protected or the disc is a finalised DVD-R. Subsequent
changes cannot be made.
Tip
3
To stop this function, press FSS & .
Hiding chapters
Initially, all the chapters are visible. You can hide chapters for playback (e.g. advertisements) or
make them visible again. In editing mode, hidden chapters are shown darker.
A chapter always consists of a start marker and an end market.
To hide a certain scene, proceed as follows:
1
Search the beginning of the scene you want to hide. Press
PAUSE 9 .
2
3
4
Press FSS & on the remote control to call the 'Favorite Scene
Selection' editing menu.
Favorite Scene Selection
Set the start marker using OK .
The number of chapters ('C') in the menu line will increase by one.
Insert marker
Press OK
visible
Current chapter
Delete marker
Delete all markers
New index picture
Divide title
Search for the end of the scene. You can also use O or N to
search faster for the end of the scene.
Make sure that you do not jump into the next title (title number 'T'
must not change). Only chapters within a title can be hidden.
5
Press PAUSE 9 at the corresponding position.
79
Managing the disc contents
6
Set the end marker with OK . This will also be the start marker of
the next chapter.
The number of chapters ('C') in the menu line increases by one.
aThe number of chapters ('C') has increased bytwo or more
numbers
b This is the case when you want to hide a chapter that, due to automatic
chapter numbering (if switched on), stretches over two or more chapters.
In this case, you must delete the start of the automatically generated
chapter:
1
2
3
Press T/C twice while the editing menu is displayed to change the
chapter number.
Select the chapter between the new markers using P- B or P+ A .
Press PAUSE 9 .
Select 'Delete marker' with P- B to delete the current chapter
marker. Confirm with OK . The current chapter number decreases by
one.
Problem
7
8
Press T/C twice to change the chapter number 'C'.
Select the previous chapter with P- B , since you are already in the
next chapter (end of the chapter is also the beginning of the next
chapter).
9
Wait until the chapter has been played and press PAUSE 9 to stop
playback.
0
A
Select 'Current chapter' using P- B or P+ A .
Using C select 'hidden'. The picture is shown darker.
Switching quickly
You can switch between show chapters ('visible') and hide chapters
('hidden') quickly and easily using SELECT .
This function is independent from the selected line.
Tip
B
To end, press FSS & .
During playback this chapter will be skipped.
If the chapter is not visible, select 'visible' in step 3 with C .
80
Managing the disc contents
Deleting chapter markers
Within a title you can delete either all markers or individual markers.
1
While the relevant chapter is playing, press FSS & on the remote
control. The 'Favorite Scene Selection' menu appears on the TV
screen.
Favorite Scene Selection
Insert marker
Press OK
visible
Current chapter
Delete marker
Delete all markers
New index picture
Divide title
How can I select different chapters?
1
Press the T/C button on the remote control. Titles and chapters are
displayed at the top of the screen.
2
3
Select title (T) or chapter (C) with C or D .
Use P+ A or P- B to select the title/chapter channel you want to edit.
Tip
2
3
Use P- B to select either 'Delete marker' for this chapter or
'Delete all markers' for all chapters within the selected title.
Confirm with OK . (You will be prompted to press OK again to
make sure you really want to delete all markers. If you do not want
to, press the D button.)
4
To end, press FSS & .
Changing the index picture
Normally the first picture of a recording is used as the index picture. You can however choose
any picture from the recording as the index picture.
1
2
During playback, search for location of the new index picture. Press
the PAUSE 9 button.
Press the FSS & button. The 'Favorite Scene Selection' menu
appears on the TV screen.
Favorite Scene Selection
3
4
Select line 'New index picture' and confirm with OK .
Insert marker
Press OK
visible
Current chapter
Delete marker
Delete all markers
New index picture
Divide title
Start the change with OK . 'Updating menu' appears on the TV
screen.
Once the revision has been completed successfully the DVD recorder reverts to the index
overview.
81
Managing the disc contents
Dividing titles
You can divide a title into several sections (titles) of any size. Each of these sections (titles) is
identified by its own index.
Note: This division cannot be undone.
Can I divide titles on DVD+R discs?
As recordings on DVD+R discs cannot be overwritten, it is not possible to
divide titles.
?
1
While the relevant title is playing, press FSS & on the remote
control. The 'Favorite Scene Selection' menu appears on the TV
screen.
Favorite Scene Selection
Insert marker
Press OK
visible
2
3
Select 'Divide title' and confirm with the OK button.
Current chapter
Delete marker
Delete all markers
New index picture
Divide title
If you are sure, press OK to start the process. 'Dividing title'
appears on the TV screen.
4
Wait until the new title is displayed with an index picture in the index
picture overview.
The process of splitting the title is now complete.
Editing recording titles (name)
Some TV stations transmit the title (name) of a programme. In this case, the name will be
included automatically (e.g. 'ROCKY'). Otherwise, the only the programme number (programme
name) and the time are stored as the name of the recording. The name of the recording can
only be changed after the recording has been completed.
1
2
If required, press the STOP h button to interrupt playback.
Using P+ A or P- B select the title whose name you want to edit
and confirm with C . The menu for editing names appears.
Settings for title Charly 1
Name
Charly 1
3
4
Select 'Name' using P+ A or P- B and confirm with C .
Play full title
Erase this title
Using C or D select the position where the letter/number/icon is to
be changed/re-entered.
5
6
Change the icon using P+ A or P- B . You can switch between
upper and lowercase using SELECT . You can delete the character
using CLEAR .
Repeat 4 and 5 until you have made the changes you want.
82
Managing the disc contents
7
8
Save the new name with OK . 'Storing name' appears on the TV
screen for confirmation.
To end, press D .
Playing the entire title
If you have hidden certain sections (chapters) of a title, this setting lets you watch the entire title
including the hidden sections. To do this, proceed as follows:
1
2
Press the STOP h button or during playback press DISC-MENU .
Using P+ A or P- B select the title you want to play all of and
confirm with C . The title editing menu will appear.
Settings for title Charly 1
Name
Charly 1
3
4
Select 'Play full title' using P+ A or P- B and confirm with OK .
Play full title
Erase this title
Press OK
Playback starts automatically. The title is played in its entirety -
including the hidden chapters.
Erasing recordings/titles
You can erase specific recordings from a disc. To do this, proceed as follows:
1
2
Press the STOP h button or during playback press DISC-MENU .
Using P+ A or P- B select the title you want to delete and confirm
with C . The title editing menu will appear.
Settings for title Charly 1
Name
Charly 1
3
4
Select 'Erase this title' using P+ A or P- B and confirm with
OK . 'This will completely erase this title' appears on the TV
screen. 'Press OK to confirm'.
Play full title
Erase this title
Press OK
If you want to delete this title, press OK to confirm. Otherwise press
D .
5
6
'Erasing title' appears on the TV screen.
At this point 'Empty title' appears in the 'index picture display'. A
new recording can now be made here.
If the deleted title was very short (less than 1 minute) 'Empty title'
will not appear at this point.
Can titles be deleted from a DVD+R disc?
Titles on DVD+R discs are only marked as deleted. 'Deleted title' will appear
in the display instead of 'Empty title'. During playback the 'deleted' title is
skipped. The space used for this title cannot be used again as the title has not
been physically deleted. Once the disc has been finalised no further changes
can be made.
?
83
Managing the disc contents
Disc settings
This screen appears beforethe first title and contains general information about the current disc.
Philips1
00:35:59 used
Fri15/02/2003
You can:
•) change the name of the disc
•) activate or deactivate write protection on the disc
•) Finish editing (make the disc DVD compatible)
•) finalise a DVD+R
PAL
DVD playback
•) delete a DVD+RW
To get to this display, proceed as follows:
1
2
3
Press the STOP h button or during playback press DISC-MENU .
Select the first title with P+ A or press STOP h .
Press the P+ A button. The disc info display will appear.
Changing the disc name
1
In the 'Disc info display' press C . The 'Settings for' menu appears
on the TV screen.
2
3
Select 'Disc name' using P+ A or P- B and confirm with C .
Settings for Philips1
Using C or D select the position where the letter/number/icon is to
be changed/re-entered.
Disc name
Protection
Erase disc
Philips1
Unprotected
4
Change the icon using P+ A or P- B . You can switch between
upper and lowercase using SELECT . You can delete the character
using CLEAR .
5
6
Repeat 3 and 4 until you have made the changes you want.
Save the new title with OK . 'Storing name' appears on the TV
screen for confirmation.
7
To end, press D .
84
Managing the disc contents
Finishing editing
If one or more titles have been edited a DVD player may still display the original titles. You can
prepare your DVD+RW disc in such a way that a DVD player will be able to play the edited
version.
1
2
In the 'Disc info display' press C . The 'Settings for' menu appears
on the TV screen.
Select 'Make edits compatible' using P+ A or P- B and confirm
with OK .
a'Make edits compatible' does not appear
b Your disc is already compatible. There is no need for conversion.
To end, press SYSTEM-MENU .
Problem
3
4
The screen displays 'This will take' to show how long the process
will last.
To confirm press OK . 'Working' appears on the TV screen. A bar
will move from left to right indicating progress.
Finalising DVD+R discs
This feature is required to play back a DVD+R disc in a DVD player. Once the disc has been
finalised no further recordings or changes can be made.
1
2
In the 'Disc info display' press C . The 'Settings for' menu appears
on the TV screen.
Select 'Finalise disc' using P+ A or P- B and confirm with OK .
a'Finalise disc' does not appear
b Either there is no DVD+R disc inserted or the disc is already finalised.
To end, press SYSTEM-MENU .
aThe 'Settings for' menu does not appear
b The menu may not appear if the disc has been recorded on another DVD
recorder. In this case, use the 'Finalise disc' feature in the '
under 'Features'.
' menu,
A
Problem
3
The screen displays 'This will take...' to show how long the process
will take.
85
Managing the disc contents
4
To confirm press OK . 'Working' appears on the TV screen. A bar
will move from left to right indicating progress.
Erase DVD+RW disks
1
2
3
In the 'Disc info display' press C . The 'Settings for' menu appears
on the TV screen.
Select 'Erase disc' using P+ A or P- B and confirm with OK .
'This will erase all titles' appears on the TV screen. Press OK to
confirm'.
Settings for Philips1
Disc name
Protection
Erase disc
Philips1
Unprotected
Press OK
If you want to delete all the titles, press OK to confirm. Otherwise
press D .
4
5
'Erasing disc' appears on the TV screen.
After deletion, the index picture display shows the free space on the
disc.
Tip
If the disc is empty already, you cannot select 'Erase disc'.
86
Managing the disc contents
LProgramming a recording (TIMER)
General
Use 'Programming a recording (TIMER)', to automatically start and stop a recording at a later
date.
The DVD recorder will switch to the right programme number and begin recording at the
correct time.
On this DVD recorder you can pre-programme up to six recordings and 3 reminders (to watch)
within a period of one month.
To make a programmed recording, your DVD recorder needs to know:
* the date you want to make the recording
* the programme number of the TV channel
* the start and stop time of the recording
* VPS or PDC on or off
* the recording mode (quality) ('M1/M2/M2x/M3/M4/M6/M8')
This information is saved in a 'TIMER block'.
Before you begin, make sure the clock is set. If the clock is not set, the 'Time/Date' menu will
appear when you press the TIMER s button.
What is 'VPS/PDC'?
'VPS' (Video Programming System)/'PDC' (Programme Delivery Control) are
used to control the start and duration of TV channel recordings. If a TV
programme starts earlier or ends later than was scheduled, the DVD recorder
will then turn on and off at the correct time.
What do I need to know about 'VPS/PDC'?
• You must enter the start time exactlyto the minute .
If you want to programme a time that is different from the VPS or PDC time,
you must switch off VPS or PDC.
• Only one TV program of a TV channel can be controlled using 'VPS/PDC' at a
time. If you want to record two or more TV programmes on a TV channel
using 'VPS/PDC', you will need to programme these as two separate
recordings.
• Since the DVD recorder requires a certain lead time (for getting the disc up to
speed and positioning the laser) before recording can start, it is possible that
the recorder will miss the first few seconds of a TV show recorded with
VPS/PDC.
?
In this case, disable VPS/PDC and enter a start time one minute earlier.
87
Programming a recording (TIMER)
Programming recordings with the GUIDE
Plus+® System
The GUIDE Plus+® System has made it even easier to programme recordings. All you have to do
is select the show you want to record from a channel listing.
1
2
3
Switch on the TV set. If required, select the programme number for
the DVD recorder.
Press GUIDE/TV on the remote control.
Use P+ A or P- B to select the TV station, and D or C to select
the show to record.
aI do not see all available TV channels
b Please check your correct channel line up in the 'Editor' screen.
Read therefore the section 'The 'Editor' screen in the chapter 'The GUIDE
Plus+® system.
b The GUIDE Plus+® 'Grid' screen contains only those TV channels that
were detected by the GUIDE Plus+® system using a 'channel identification'.
TV channels that do not have this 'channel identification' are not available in
the GUIDE Plus+® system.
Please use 'Manual TIMER programming' to program TV shows of such TV
channels.
Problem
4
Confirm using the red function button of the remote control
('Record' on the screen).
You can also use REC/OTR n on the remote control or
RECORD on the DVD recorder.
The TV show is programmed for recording.
Read the information on the screen.
a'Warning, this programme number has not been allocated, please
go to Editor to set it.' appears on the screen
b The programme number of the TV channel is not available in the GUIDE
Plus+® system or allocation is wrong.
To change or check the channel data, proceed as follows:
1
2
3
4
Press P+ A .
Select 'Editor' with C .
Select the TV channel using P- B or P+ A .
Press C to go to the right tile.
In case you can receive the selected channel only via an external
receiver, press the red button to select the corresponding source.
Press the green button.
5
6
Enter the programme number of the TV channel using the number
buttons.
If the source you have selected is an external receiver, enter the
programme number that you would also enter at the external receiver
for this TV channel.
Problem
88
Programming a recording (TIMER)
You can also program TV shows that you just want to watch
Press the green function button ('Watch' on the screen) instead of the red.
The TV show is stored in the memory for favourite shows. The line is
displayed in a different colour.
Tip
5
6
Repeat steps 3 to 8 , until all recordings have been programmed.
To end, press GUIDE/TV .
To find out how you can check which shows you have programmed, read the section on 'How
to change or delete a programmed recording (TIMER)'.
7
8
9
Insert a DVD ready for recording (not locked).
The inserted disk is checked.
Search the position on the disc where you want the recording to
begin.
Switch off the DVD recorder using STANDBY m .
The programmed recording functions only if the DVD recorder has
been switched off using STANDBY m .
If one or more recordings have been programmed 'TIMER' will light up on the display.
Programming recordings with the VIDEO
Plus+® System
Thanks to this programming system, you no longer need to tediously enter the date, programme
number, start and finish time. All the information needed by the DVD recorder for programming
is contained in the PlusCode programming number. This 9-digit PlusCode number is found in
most TV listings magazine.
WARNING!
'Programming with the VIDEO Plus+® system' may not be possible without GUIDE Plus+® data
(empty 'Grid' screen).
1
2
3
Switch on the TV set. If required, select the programme number for
the DVD recorder.
Press TIMER s on the remote control.
The 'Schedule' screen will appear
Press the red function button ('VIDEOPlus+ ').
If this button is not visible in the menu line or without function, no
GUIDE Plus+® data is yet available. Therefore, you cannot use
programming with the VIDEO Plus+® system yet.
89
Programming a recording (TIMER)
VIDEOPlus+ Manual
Home
4
5
Enter the entire PlusCode number. This number is up to 9 digits long
and can be found next to the start time of the TV programme in your
TV listings magazine.
e.g.: 5-234-89 or 5 234 89
Enter 523489 for the PlusCode number.
Use therefore the number buttons 0..9 on the remote control.
If you make a mistake you can press D or the green action button to
go back a position.
Please enter the PlusCode programming number and
press OK to confirm.
= = = = = = = = =
Grid
Search
Schedule Info
No programmes
M2 Once
0
Confirm with OK .
a'VIDEOPlus+ system ' appears on the screen
b This message appears when the TV channel has not been assigned in the
GUIDE Plus+® system yet.
To change channel data, proceed as follows:
1
2
3
4
Press P+ A .
Select 'Editor' with C .
Select the TV channel using P- B or P+ A .
Press C to go to the right tile.
In case you can receive the selected channel only via an external
receiver, press the red button to select the corresponding source.
Press the green button.
5
6
Enter the programme number of the TV channel using the number
buttons.
If the source you have selected is an external receiver, enter the
programme number that you would also enter at the external receiver
for this TV channel.
7
Confirm with OK .
aThe following message appears on the screen: 'PlusCode number
wrong'
b The entered PlusCode number is incorrect. Repeat the entry or end with
TIMER s .
b Check time/date (see chapter 'Installing your DVD recorder', section
'Setting the time & date').
Problem
VIDEOPlus+ Manual
Home
6
The decoded data appears after confirmation.
Please enter the PlusCode programming number and
press OK to confirm.
You can use the colour buttons to make the following settings. First,
the right tile must be highlighted ( C button). Check the functions
(descriptions) in the corresponding colour field before pressing a
button.
1 2 3 4 5 = = = =
Grid
Watch/Record
21-Oct 20:00 21:30 BBC1 M2
Search
Schedule Info
Qual. Freq. Timing
Once
0
Extending end time
Enter the minutes you want the recording to last longer using the yellow
button.
Activate 'VPS/PDC'
Keep pressing the yellow action button until 'VPS/PDC' appears instead of the
time.
Setting up repeat recordings
You can choose from the following settings with the green action button:
'Frequency':'Once': single recordings
'M-F': Repeated daily recordings (Monday to Friday).
'Mon': Repeated weekly recordings (every week on the same day
e.g. Monday).
Entering the recording quality
You can choose from the following settings in the right tile using the red
action button: 'M1, M2, M2x, M3, M4, M6, M8'.
Tip
90
Programming a recording (TIMER)
7
8
9
If all information is correct, press the OK button. The data is stored.
To end, press TIMER s .
Insert a recordable disc (one without write protection).
The inserted disk is checked.
0
A
Search the position on the disc where the recording should begin.
Switch off the DVD recorder using STANDBY m .
The programmed recording functions only if the DVD recorder has
been switched off using STANDBY m .
If one or more recordings have been programmed 'TIMER' will light up on the display.
Programming recordings without the
VIDEO Plus+® System
1
2
Switch on the TV set. If required, select the programme number for
the DVD recorder.
Press TIMER s on the remote control.
The 'Schedule' screen appears
VIDEOPlus+ Manual
Home
3
Press the green button.
The current date will be displayed.
Schedule displays programmes for Watch or Record.
Press Bto use. Press the Red button for VIDEOPlus+
recording. Press the Green button for Manual
recording. Press Dfor Search. Press Cfor Info.
4
5
Enter the date using the number buttons 0..9
Grid
Search
Schedule Info
No programmes
Confirm with OK .
How can I correct wrong entries?
If you have already confirmed the entry with OK , you can select one of the
following functions:
Repeat entry: Green colour button
Cancel: Red colour button
?
6
7
Enter the start time for the show using the number buttons 0..9 .
Confirm with OK .
Enter the finish time for the TV show using the number buttons
0..9 Confirm with OK .
91
Programming a recording (TIMER)
8
9
Check the data you entered.
If necessary, go back a position to change entered data using the green
function button.
Enter the programme number of the TV channel using the number
buttons 0..9
Quality
Frequency VPS/PDC Home
Recording quality M2, Recording quality M2
Selecting a TV channel from the listing
You can only use this function if data from the GUIDE Plus+® system is
already available.
Grid
Watch/Record
21-Oct 20:00 21:30 BBC1 M2
Search
Schedule Info
Qual. Freq. Timing
Once +0
1
2
3
Press the yellow function button. You will see an overview of all
channels
Select the TV channel you want to program using D , C , P- B ,
P+ A . You can browse back or forth using O , N .
Confirm with OK .
Programme numbers of the scart sockets 'EXT1', 'EXT2' and the
front sockets 'CAM1', 'CAM2'
You can also program recordings from external sources.
1
Select the corresponding input socket using P- B or P+ A . 'EXT1'
( EXT TO TV-I/O ), 'EXT2' ( EXT AUX-I/O ), 'CAM1'
1
2
( S-VIDEO and VIDEO ), 'CAM2' ( DV IN ).
2
Confirm with OK .
Tip
Changes using the colour buttons
You can use the colour function buttons to make the following settings. Make
sure that the right tile is selected.
'Qual.': Red function button
Select the recording quality
'Frequency' : Green function button
'Once': single recordings
'M-F': Repeated daily recordings (Monday to Friday).
'Mon': Repeated weekly recordings (every week on the same
day, e.g. Monday).
Activate VPS/PDC ('Timing'): Yellow function button
Using this button, you can activate (appears)
or deactivate ('VPS/PDC' disappears)
Tip
'VPS/PDC' in tile 'Timing'
0
A
To find out how you can go back and change the data, read the
section on 'How to change or delete a programmed recording
(TIMER)'
.
Insert a DVD ready for recording (not locked).
The inserted disk is checked.
B
C
Search the position on the disc where the recording should begin.
Switch off the DVD recorder using STANDBY m .
The programmed recording functions only if the DVD recorder has
been switched off using STANDBY m .
If one or more recordings have been programmed 'TIMER' will light up on the display.
92
Programming a recording (TIMER)
How to change or delete a programmed
recording (TIMER)
1
2
Switch on the TV set. If required, select the programme number for
the DVD recorder.
Press TIMER s on the remote control while the DVD recorder is
switched on. The 'Schedule' screen will appear.
Quality
Frequency VPS/PDC Home
3
Use P- B or P+ A to select the programmed recording you want
to change or delete.
Recording quality M2, Single recording
Depending on the programming method (using GUIDE Plus+® system,
with/without VIDEO Plus+® system), it is not possible to carry out
certain changes using the function buttons. Therefore, always check
the function of the corresponding button (description in the colour
field) before pressing the button.
Grid
Watch/Record
21-Oct 20:00 21:30 BBC1 M2
21-Oct Matrix M2
Search
Schedule Info
Qual. Freq. Timing
Once +0
Once
0
Delete programmed recording
Press the red action button in the left tile.
Changing the TV channel
You can make this change only for recordings that were not set using the
'Grid' screen.
In the case of recordings using the 'Grid' screen, centre tile is not available.
1
2
3
4
Select the centre tile with C .
Press the yellow function button.
Select the TV channel you want using P- B , P+ A , D , C .
Confirm with OK .
Activate VPS/PDC
Keep pressing the yellow function button in the right tile until 'VPS/PDC'
appears in the 'Timing' line instead of the time.
Prolonging finish time
For manually programmed recordings, you can only perform this change in the
left tile using the green function button.
1
2
Select the right tile with C .
Select the later time at which the recording is to finish using the yellow
function key.
Setting up repeat recordings
You can choose from the following settings in the right tile using the green
function button:
'Frequency' :'Once': Once recordings
'M-F': Repeated daily recordings (Monday to Friday).
'Mon': Repeated weekly recordings (every week on the same
day, e.g. Monday).
Entering recording quality(' Quality')
You can choose one of the following settings in the right tile using the red
Tip
function button. M1, M2, M2x, M3, M4, M6, M8'.
4
5
To end, press TIMER s .
Switch off with STANDBY m .
93
Programming a recording (TIMER)
'NexTView Link'
This DVD recorder is equipped with the 'NexTView Link' feature. If your television is also
equipped with 'NexTView', you can mark TV programmes on the television for programming.
These TV programmes will automatically be transmitted to a TIMER block on the DVD
recorder.
For more information, read the instruction manual of your TV set.
Problem solving for programmed
recordings
PROBLEM
SOLUTION
The DVD recorder is
not responding
bWhile a programmed recording is being made, you cannot operate your DVD recorder manually.
If you want to cancel the programmed recording, press STANDBY m .
'Switch off, timer
recording' flashes on
the TV screen.
bThe DVD recorder was switched on a few minutes before the start of a programmed recording.
Switch off the DVD recorder using STANDBY m . A programmed recording (timer) will only
function if the DVD recorder is switched off ( STANDBY m button).
bEither a disc has not been inserted or the disc cannot be used for recording. Insert a disc on
which recordings can be made.
Search the position on the disc where you want the recording to begin.
Switch off the DVD recorder using STANDBY m .
Error message: 'Insert
recordable disc'
The error message
'Disc locked' appears
brieflyon the screen.
bA write-protected disc has been inserted. Undo the write protection (see 'Preventing accidental
erasing of discs' in 'Manual recording') or insert a different disc.
94
Programming a recording (TIMER)
MUser preferences
In this section you will learn how to set your user preferences on the DVD recorder. The
symbols have the following meanings:
Picture setting
t
v
Sound setting
Language setting
Additional settings
u
w
x
Remote control settings
Control the DVD recorder using the remote control of your Philips TV
set
Disc settings
s
z
y
Recording settings
Installation
1
2
Switch on the TV set. If required, select the programme number for
the DVD recorder.
Press SYSTEM-MENU on the remote control. The menu bar
appears.
3
4
Select ' ' using D or C and confirm with P- B .
A
Select the appropriate function with P- B or P+ A and confirm
with C .
5
6
Select the appropriate line using P- B or P+ A and confirm with
C .
Select the appropriate function using P- B or P+ A or the setting
with D or C .
7
8
Confirm the new setting by pressing OK .
To close the menu item, press D .
95
User preferences
Picture settings
You can choose the following features in this menu:
'TV shape'
The picture signal from your DVD Recorder can be set to match your TV screen.
Picture
TV shape
16:9
Off
'4:3 letterbox': for a 'wide-screen' picture with black bars at the top and bottom
'4:3 panscan': for a full-height picture with the sides trimmed.
'16:9' : for a wide-screen TV set (screen edge ratio 16:9)
Black level shift
Video shift
ï
Video output
RGB + CVBS
'Black level shift'
Adapts the colour dynamics for NTSC playback when switched to 'On'
'Video shift'
Use this feature to adjust the position of the picture on your TV left or right using D , C to
suit your TV set.
'Video output'
Since RGB and S-Video signals sometimes use the same connections on a scart cable, the two
signals cannot be transmitted simultaneously. With these settings, you can decide whether RGB
or S-Video signals should be transmitted. This setting affects only the scart sockets of the DVD
recorder ( EXT 1 TO TV-I/O output socket and EXT 2 AUX-I/O input socket).
Please also observe which signals are available at which scart socket of the TV set or how the
scart sockets need to be switched.
If necessary, consult the instruction manual of your TV set.
Which settings can I select?
'RGB + CVBS' Depending on the TV set you are using, switching between the
'RGB' and the 'Video(CVBS/FBAS)' signal is done automatically.
If the picture scrolls to the side or the colour quality is poor
on some TV sets when the setting is 'RGB + CVBS', you
must select 'CVBS only'.
'S-video only' Both scart sockets ( EXT 1 TO TV-I/O output socket and
EXT 2 AUX-I/O input socket) process only the S-Video signal.
In case the scart socket of the TV set is not suitable for S-Video
(Y/C) signals, you will only see a black-and-white picture,
although the recording will be made in colour.
Moreover, only the video (CVBS, FBAS) signal will be used for
recordings via the EXT 1 TO TV-I/O scart socket.
Please observe that when making recordings from a video
recorder that transmits only video (CVBS/FBAS) signals through
the scart cable, recordings via scart socket EXT 2
AUX-I/O may be made in black and white.
Therefore, use this setting with caution.
'CVBS only' Only the video (CVBS/FBAS) signal is transmitted regardless of
the video signals (RGB, Y/C) on the scart sockets. This setting is
selected automatically when no 'RGB' or 'S-VIDEO' signal is
detected at the scart socket.
When selecting the settings 'S-video only' or 'CVBS only', the RGB signal
is switched off.
?
96
User preferences
Sound settings
Depending on which audio outputs are used, you can select the settings in this menu.
If you only use the analogue audio output ( OUT AUDIO L/R ), select the settings 'Off' in the
'Digital output' menu.
'Digital output'
You can select one of the following settings for devices that are connected to the COAX
OUT or OPTICAL AUDIO OUT sockets:
Sound
Digital output
Analogue output
Night mode
All
Stereo
Off
'All': Dolby Digital and DTS signals are fed unaltered to the digital output. MPEG-2 multi-channel
signals are converted to PCM (Pulse Code Modulation).
For receivers/amplifiers with digital multi;channel sound decoders.
'PCM only: Dolby Digital and MPEG-2 multi-channel signals are converted to PCM (Pulse Code
Modulation).
For receivers/amplifiers without digital multi;channel sound decoders.
'Off: Digital output switched off.
For devices with analogue audio input.
'Analogue output'
For devices connected to the analogue audio output ( OUT AUDIO L/R ), you can select from
the following settings.
'Stereo': For devices without DolbySurround or TruSurround. Use this setting if the DVD
recorder is only connected to a stereo TV set.
'Surround: Dolby Digital and MPEG-2 multi-channel are mixed down to a DOLBY
surround-compatible two-channel output signal.
For devices with DolbySurround Pro Logic decoder .
'Night mode'
Night mode optimises the sound for playback at low volume. You are therefore less likely to
disturb your neighbours. This only works for Dolby Digital audio on DVD video discs.
Language settings
You can choose the following settings in this menu:
'Audio Language'
Playback audio language
Language
Audio Language
Recording audio
Subtitle
English
Language 1
English
'Recording audio'
Menu
English
Selection of audio recording for bilingual programmes
97
User preferences
'Subtitle'
Subtitle language
'Menu'
Screen menu language
Additional settings
You can select the following functions in this menu:
'Status box'
Along with the on screen menu, the OSD (On Screen Display) also displays information on the
current operating status (counter, playback, recording, TV channel, etc.) on the TV screen.
You can switch off the information about the operating status so that the on screen display
(OSD) is not recorded during copying.
Features
Status box
Standby
Display
On
Off
Bright
'On': The OSD information appears in every selected mode for a few seconds and disappears
again.
'Off': The OSD information is switched off. It is no longer displayed on the screen.
'Standby'
To save power, you can switch off the clock display on the DVD recorder. Programmed
(TIMER) recordings will still take place.
In addition, you can present the most important features of the DVD recorder in scrolling text
in the display (demo).
'Low power': If the DVD-Recorder is switched off (button STANDBY m ), the clock display is
also switched off.
'Off': If the DVD-Recorder is switched off (button STANDBY m ), the clock display is visible.
'Demo mode': If the DVD recorder is switched off with the STANDBY m button, a list of the
most important features is shown in the display.
'Display'
You can change the brightness of the display on the DVD recorder. This setting only affects the
DVD recorder when it is switched on.
You can also adjust this setting with the DIM button on the remote control.
'Bright': The display appears with normal brightness. The disc tray light is switched on.
'Dimmed': The display appears less bright. The disc tray light is switched off.
'Off': The display and the disc tray light are switched off.
98
User preferences
Remote Control settings
In this menu you can set the remote control type to which your DVD recorder should respond.
'DVD player': The DVD recorder responds to the supplied remote control and the remote
control of a DVD player (remote control code RC-6).
Choose this setting if your Philips TV remote supports DVD functions.
'DVD recorder': The DVD recorder only responds to the supplied remote control.
Disk feature menu
In this menu you can make the changes that relate to the disc:
'Access control'
Please read the next chapter on 'Access control (child lock)'.
Disc features
Enter code…
On
Access control
Auto resume
'Auto resume'
If playback of a pre-recorded DVD video disc or video CD is interrupted (button STOP h or
OPEN/CLOSE J ) when the disc is reloaded (disc is started) playback starts at the precise
location where it stopped. This applies not only to the current disc but to the last 20 discs
played.
This feature can be switched off if not required.
'PBC'
This line appears only if a VCD is loaded.
This function lets you activate or deactivate the PBC menu (Playback Control) for video CDs.
See 'Playing a (Super) Video CD'.
'Finalise disc'
This feature allows you to finalise DVD+R discs. If the disc has already been finalised this line will
appear darker.
'Adapt disc format'
If a DVD+RW has been recorded in a computer drive or in another DVD recorder the index
screen may not be displayed correctly.
This feature allows you to change the format of the disc.
It is therefore only visible if the disc format is different.
99
User preferences
NAccess control (Child Lock)
Child lock (DVD and VCD)
This feature enables discs to be locked for children.
When Child Lock is on, a 4-digit code (PIN) needs to be entered before a disc can be played.
You can also decide whether the inserted disc should always be played or should be played only
once, despite the child lock
•)'Play always':
This disc is stored in a memory with space for 50 child-safe discs. If more than 50 discs are
stored, the last disc in the list is removed and the new disc is added. The screen shows 'Child
safe' at the start of playback.
•)'Play once':
This disc is only authorised for single playback. If the recorder is switched off, the PIN code
must be re-entered.
Activating/deactivating child lock
1
Switch on the TV set. If required, select the programme number for
the DVD recorder.
2
3
4
5
Switch on the DVD recorder using STANDBY-ON m .
Press SYSTEM-MENU . The menu bar appears
Select the ' ' icon using D or C .
A
Select ' (Disc features)' using P- B or P+ A and confirm with
s
C .
6
7
Confirm 'Access control' using C .
Enter a 4-digit code of your choice. If the code is new, you may have
to enter the code a second time as confirmation.
Disc features
Enter code…
On
Access control
Auto resume
8
9
0
A
Select 'Child lock' using P+ A or P- B and confirm with C .
Select the ' ' icon using P- B or P+ A .
i
Confirm with OK .
Quit the feature using D and SYSTEM-MENU .
Unauthorised discs can only be played by entering the four-digit PIN code.
To deactivate the child lock, select the ' ' icon in 9 .
n
100
Access control (Child Lock)
Authorising a disc
1
2
3
Insert a disc. The access control box will appear after a short delay.
Using P+ A or P- B select 'Play once' or 'Play always'.
Enter your PIN code using the number buttons 0..9 .
Double-sided DVDs may have a different ID for each side. For these discs, each side must be
authorised. Video CDs may have a different ID for each disc. For these CDs, each disc must be
authorised.
Locking unlocked discs
To lock a disc that was formerly authorised follow the instructions below
1
2
Insert a disc. Playback starts automatically. If the playback does not
start automatically, press PLAY G .
Press the STOP h button while the '
' icon is visible. The icon
m
changes to ' '. The disc is now locked.
l
Parental level control (DVD video only)
Films on pre-recorded DVD discs may contain scenes not suitable for children. Therefore, some
discs may contain 'Parental Control' rating information that applies to the entire disc or to
certain scenes on the disc.
The appropriate scenes have filter values that reach from 1-8. If such a scene is detected during
playback, the filter value set on the DVD recorder is compared to the scene. If the filter value is
higher than the setting, an alternative scene will be played (if available).
Most DVDs apply the rating to an entire DVD. Therefore, if certain scenes exceed the rating
you select, the entire disc will be blocked from viewing.
Activating/deactivating parental level
control
1
Switch on the TV set. If required, select the programme number for
the DVD recorder.
2
3
4
5
Switch on the DVD recorder using STANDBY-ON m .
Press SYSTEM-MENU . The menu bar appears
Select the ' ' icon using D or C .
A
Select ' (Disc features)' using P- B or P+ A and confirm with
s
C .
101
Access control (Child Lock)
6
7
Confirm 'Access control' using C .
Enter a 4-digit code of your choice. If the code is new, you may have
to enter the code a second time as confirmation.
Disc features
Enter code…
On
Access control
Auto resume
8
9
Select the 'Parental level' using P+ A or P- B and confirm with
C . A bar appears to select the parental level.
Select the appropriate rating using P- B , P+ A or the number
buttons 0..9 .
What do the ratings mean?
Rating 0 (displayed as '--') parental control not active.
Rating 1 (suitable for children)
Rating 8 (only suitable for adults)
What happens if a DVD scene contains a higher level than the rating
set?
If the recorder does not find a suitable alternative, playback will stop and you
must enter the four-digit code.
Tip
0
Confirm with OK . Quit using D and SYSTEM-MENU .
Changing the country
The set filter values depend on the respective country. It is therefore necessary to enter the
country to which these filter values apply.
1
Switch on the TV set. If required, select the programme number for
the DVD recorder.
2
3
4
5
Switch on the DVD recorder using STANDBY-ON m .
Press SYSTEM-MENU . The menu bar appears
Select the ' ' icon using D or C .
A
Select line ' (Disc features)' using P- B or P+ A and confirm
s
with C .
6
7
Confirm the line 'Access control' using C .
Enter your four-digit code. If the code is new, you may have to enter
the code a second time as confirmation.
Disc features
Access control
Auto resume
Enter code…
On
8
9
0
Select 'Change country' using P- B or P+ A and confirm with
C .
Select the corresponding country using P+ A or P- B and confirm
with OK .
To end, press D and then SYSTEM-MENU .
102
Access control (Child Lock)
Changing the PIN code
1
Switch on the TV set. If required, select the programme number for
the DVD recorder.
2
3
4
5
Switch on the DVD recorder using STANDBY-ON m .
Press SYSTEM-MENU . The menu bar appears
Select the ' ' icon using D or C .
A
Select ' (Disc features)' using P- B or P+ A and confirm with
s
C .
6
7
Confirm 'Access control' using C .
Enter your four-digit PIN code. If the code is new, you may have to
enter the code a second time as confirmation.
Disc features
Enter code…
On
Access control
Auto resume
8
9
Select 'Change code' using P+ A or P- B and confirm with C .
Enter the new code using the number buttons 0..9 . Enter the same
code again as confirmation.
0
Quit using D and SYSTEM-MENU .
I have forgotten mycode
Press STOP h four times (step 7 ), then press OK . Access control is
Tip
now switched off. You can now enter a new code as described above.
103
Access control (Child Lock)
OBefore you call an engineer
If you have any problems using this DVD recorder, the reason may be one of the following. You
can also call the customer service centre in your country.
The telephone numbers can be found on the back of this instruction manual.
You can also visit our web page 'http://www.p4c.philips.com' .
Have the model number (MODEL NO) and the production number (PROD.NO) of your
recorder ready.
The production number (PROD. NO.) is printed on the type plate at the back.
PROBLEM
SOLUTION
Your recorder does
not respond to any
button being pressed
and the displayshows
'IS TV ON?':
bRecorder in initial installation mode: Switch on the TV, switch over to the DVD recorder socket.
Now the menu for language selection should appear. Please read paragraph 'Initial Installation' in
the chapter 'Installing your DVD Recorder'.
The following text should now appear on the screen ''. Please read paragraph 'Initial Installation' in
the chapter 'Installing your DVD Recorder'.
b'Dealer-Mode' is switched on: All buttons on the front of the set are locked.
Switch off the function:
The device does not
react when you press a
button, although the
remote control works:
1 Pull out the mains plug from the wall outlet.
2 Press and hold down h and OPEN/CLOSE J and put back the mains plug into the wall
outlet.
3 As soon as the time or '--:--' appears in the display (ca. 6 - 10 seconds), release h and
OPEN/CLOSE J .
bThere is no power supply: check the power supply
bA programmed recording (Timer) is currently being made: If desired, cancel the programmed
recording (Timer) with STANDBY m .
bThere is a technical problem: disconnect from the mains power supply for 30 seconds, then
connect again.
If this doesn't help, you can reset your DVD recorder to the default factory settings.
Your DVD recorder
does not respond to
anybutton being
pressed:
bImportant:
All the information stored (TV channels, time and date, TIMER) will be lost.
1 Disconnect from the mains power supply.
Resetting the machine
to the default factory
settings
2 Press and hold down the STANDBY-ON m button on the device and reconnect to the
mains power supply.
3 Release the STANDBY-ON m button when 'IS TV ON?' appears on the display. All the
information stored (TV channels, time and date, TIMER) will be lost.
Please read paragraph 'Initial Installation' in the chapter 'Installing your DVD Recorder'.
bRemote control not pointed toward the DVD recorder: Point the remote control at the machine.
See if the 'o(((' appears on the display briefly each time you press a remote control button. If it
does, the Recorder is receiving information from the remote correctly.
bThere is a technical problem: Take out the batteries, wait for 10 seconds and put them in again.
bBatteries are flat: Change the batteries.
Remote control does
not work:
104
Before you call an engineer
PROBLEM
SOLUTION
bData transfer is controlled via pin nr. 10 of the scart cable. It is possible that the connection to
this pin is interrupted or that the signal is distorted by an additional device connected to the
EXT 2 AUX-I/O socket.
bRemove any scart switch boxes, mixing consoles, signal amplifiers, ... connected between the DVD
recorder and the TV set. Connect the DVD recorder directly to the TV set.
bRemove any additional devices from the EXT 2 AUX-I/O socket.
bTry using another scart cable (all pins wired).
Data transfer from TV
set via 'EASYLINK'
does not work:
bPlease observe the installation order:
1) Switch on the TV set
2) Connect the DVD recorder to the mains
3) Switch on the DVD recorder using STANDBY m
4) The data transfer should now work.
bThere is no recording on the disc: Change disc.
bYou inserted the wrong disc type: Your recorder can play back the following disc types: DVD
Video, (Super)Video CD, DVD+R(W), Audio CD, , MP3-CD's
bYou inserted the disc the wrong way: Insert the disc with the label facing upwards
bDisc is dirty: Clean the disc
bWrong region code: The region code of the DVD and the DVD recorder must match.
bParental control is on: Read chapter 'Access control (child lock)'
No playback on DVD
recorder:
bYou have selected the wrong programme number for the DVD recorder on the TV: on the TV,
select the correct programme number for the DVD recorder.
bThe cable connecting the TV set and the DVD recorder has come loose: check the cable.
bIt is possible that this (Super) Video CD contains a menu and the 'PBC' is switched off. You can
see this in status field 'PBC OFF'. To activate this function, proceed as follows:
1 Press SYSTEM-MENU while the (Super) Video-CD is inserted .
I cannot playback
(Super) Video CDs
2 Select ' ' using D or C .
A
3 Select line 'Features' using P- B or P+ A and confirm with C .
4 Select 'On' in line 'PBC' using P- B or P+ A .
5 Confirm with OK and end with SYSTEM-MENU .
Poor playback on DVD
recorder: (distorted
picture/distorted
sound)
bYour TV set is not properly adjusted.
bDisc is dirty: Clean the disc
bSometimes the picture may be temporarily distorted. This is not a defect of your DVD recorder.
bThe TV channel you want to record is not stored or you selected the wrong programme number:
Check TV channels stored.
No recording possible:
bDisc write-protected (recording protected): Remove write-protection or change the disc. For
more information, please see 'Preventing accidental erasing of discs' in chapter 'Manual Recording'.
bAn already finalised DVD+R has been inserted: Change disc.
bYou have programmed the wrong time or date: Check time/date.
bYou have not set the TIMER properly: Check the programmed recordings (TIMER block).
bLocked disc inserted: Remove disc lock.
bAn already finalised DVD+R has been inserted: Change disc.
b'VPS/PDC' switched on but 'VPS/PDCtime' wrong: 'Enter 'VPS/PDCtime exactly to the minute.
Check the aerial.
Programmed
recording does not
work:
105
Before you call an engineer
PROBLEM
SOLUTION
bThe programme number of the TV channel is not available in the GUIDE Plus+® system or
allocation is wrong.
To change or check the channel data, proceed as follows:
1 Press GUIDE/TV .
2 Press P+ A .
3 Select 'Editor' with C .
4 Select the TV channel using P- B or P+ A .
The wrong TV channel
was decoded (entered)
after you programmed
a recording using
5 Press C to go to the right tile.
In case you can receive the selected channel only via an external receiver, press the red
button to select the corresponding source.
VIDEO Plus+ System.
6 Press the green button.
7 Enter the programme number of the TV channel using the number buttons.
If the source you have selected is an external receiver, enter the programme number that
you would also enter at the external receiver for this TV channel.
8 Confirm with OK .
bDVD recorder is switched on: Switch off the DVD recorder to allow data transfer
bThe TV channel that transmits the GUIDE Plus+® data is not set properly.
bExternal receiver (satellite receiver, set-top box, cable TV box, ...) (if available) is switched off:
switch on the external receiver
bG-LINK cable is not connected: Connect the G-LINK cable and make the necessary settings to
control the external receiver (see chapter 'The GUIDE Plus+® system', section 'Installation of the
'External receiver 1'').
There is no channel
overview in the GUIDE
®
Plus+ system
Missing or wrong TV
channel in the 'Grid'
screen
bWrong local post code/country was entered
bPlease check your correct channel line up in the 'Grid' screen.
Read therefore the section 'The 'Editor' screen.
bThe GUIDE Plus+® system was not completely installed or local post code was not entered.
1 Check the settings
When you press
GUIDE/TV the GUIDE
2 Select the corresponding line using P- B or P+ A and confirm with OK .
®
Plus+ setup screen will
3 For more information on the individual functions, see chapter 'The GUIDE Plus+® system',
appear
section 'Installation of the 'External receiver 1''.
The external receiver
does not always react
to Remote control
signal.
bThe Infrared (IR) Remote control signal interfere with the IR signal of the G-LINK transmitter.
Put the G-LINK transmitter closer to the front of the external receiver.
Myexternal receiver
switches automatically
through the TV
channels
bIf the DVD-Recorder is switched off ( STANDBY m button) the external receiver will be used
from the GUIDE Plus+® system via the DVD-Recorder. If you want to watch TV-Channels from
the external receiver, you have to switch the DVD-Recorder on.
bBefore recording, select the recording mode as described in chapter 'Manual Recording', section
'Selecting the recording mode (quality)'.
bHave your aerial checked.
bYou will find information on how to change the TV system in 'Manual TV channel search' in
'Installing your DVD recorder'.
There is picture or
sound interference on
TV reception:
106
Before you call an engineer
PROBLEM
SOLUTION
Distorted sound
coming from a
connected hi;fi
amplifier
bThe DVD recorder is connected to the 'Phono-input' of your amplifier: This socket is provided
only for record players without a preamplifier. Select a different audio input.
The picture is
distorted or
black;and;white during
playback
bThe TV system of the disc does not match that of your TV set (PAL/NTSC).
bThe recording can be made in colour only when the TV channels or the connected additional
device send a colour signal. Black-and-white signals containing no color information (colour
subcarriers) cannot be recorded.
No sound signal at the
digital output
bCheck whether the sound settings match the selected inputs and connected additional devices.
For more information, see section 'Sound setting' in chapter 'User preferences'.
bIf a recording is too short, it is possible that a DVD player cannot detect it: Please observe the
following 'Minimum recording times':
Recording mode 'M1': 5 minutes, 'M2': 10 minutes, 'M2x': 13 minutes, 'M3': 15 minutes, 'M4': 20
minutes, 'M6': 30 minutes, 'M8': 30minutes,
bSome DVD players cannot play back DVD+RW recordings. You can solve this problem by using a
special function:
1 Open the disc tray with OPEN/CLOSE J . Insert the disc but do not close the tray.
A DVD+RW disc
cannot be played on
certain DVD players
2 Hold down the number button 2 on the remote control until the tray closes. The disc is
modified.
3 If this fails to produce the desired result, repeat the procedure using the number button
3 on the remote control.
4 You can restore the disc to its original condition by pressing 1 .
Warning!
There is a risk that you can no longer play the disc on other DVD players after this procedure.
Therefore, apply this function with particular care.
bIf it is impossible to play back a disc, you can try and repair it for new recordings using the
following function. This will only prepare the disc for erasing. It will not be erased, however, until
the recording has been completed.
1 Clean the disc
Other disc errors
(DVD+RW)
2 Open the disc tray with OPEN/CLOSE J . Insert the disc but do not close the tray.
3 Hold down CLEAR on the remote control until the tray closes. The disc is prepared for
erasing.
4 Start recording as with an empty disc.
107
PROBLEM
SOLUTION
bThis message may appear if you instert a disc that was not finalised. DVD+R's that have not been
finalised are very sensitive to fingerprints, dust, or dirt. This may cause problems during recording.
To use the disc again, follow the next steps
1 Make sure that the surface of the disc is clean.
2 Open the disc tray with OPEN/CLOSE J . Insert the defect DVD+R but do not close
the tray.
Other disc errors
(DVD+R), 'Disc
contains unknown
data'
3 Hold down 5 on the remote control until the tray closes. The disc will be read ('READING'
appears on the display) and the DVD recorder will start the repair process. This may take up
to four times as much time as the recording, in which the error occurred.
4 If the disc is recovered, the index screen will appear.
Please observe the following:
Error during recording: The title may be missing.
Error while changing the title/index picture: The original title/index picture may be visible.
Error while finalising: The disc appears not to have been finalised.
bYou can finalise the disc using the following function:
1 Open the disc tray with OPEN/CLOSE J . Insert the defect DVD+R but do not close
The index screen
flickers when a DVD+R
is inserted
the tray.
2 Hold down 4 on the remote control until the tray closes.
'FINALIZE' appears in the display. Finalising begins. This may take up to three minutes.
3 If finalising has been successful, the index screen will appear.
108
PHILIPS NORGE AS
Sandstuveien 70,
PO Box 1, Manglerud
N-0612 Oslo
PHILIPS
PHILIPS PORTUGUESA, S.A.
Consumer Information Centre
Rua Dr. António Loureiro Borge, nr. 5
Arquiparque, Miraflores
Philips Austria GmbH
Triesterstrasse 64
1101 Wien
NORWAY
AUSTRIA
P-2795 L-A-VEHLA
Phone: 2274 8250
Tel: 0810 00 12 03
PORTUGAL
Phone: 352-1-4163063
OY PHILIPS AB
Sinikalliontie 3,
02630 Espo
PHILIPS INFO CENTER
Alexanderstrasse 1
20099 Hamburg
PHILIPS CE, The Philips Centre,
420 - 430 London Road,
Croydon, Surrey
Helsinki
GERMANY
CR9 3QR
FINLAND
puh. (09) 6158 0250
Tel: 0180-535 6767
UNITED KINGDOM
Phone: 0870-900-9070
PHILIPS KUNDTJÄNST
Kollbygatan 7,
SERVICE CONSOMMATEURS PHILIPS
BP 0101
PHILIPS KUNDECENTER
Frederikskaj 6,
Akalla,
16485 Stockholm
SWEDEN
75622 Paris Cédex 13
FRANCE
Phone: 0825-889 789
DK-1780 København V
DENMARK
Tlf: 808 82814
Phone: 08-5985 2250
PHILIPS POLSKA
AL. Jerozolimskie 195B
02-222 Warszawa
POLSKA
PHILIPS ELECTRONICS IRELAND LIMITED
Consumer Information Centre
Newstead, Clonskeagh
PHILIPS REPRESENTATION OFFICE
Ul. Usacheva 35a
119048 MOSCOW
DUBLIN 14
RUSSIA
Tel.: (022)-571-0-571
Phone: 01-7640292
Phone: 095-937 9300
PHILIPS SERVICE
V Mezihori 2
180 00 Prage
CZECH REPUBLIC
Phone: (02)-3309 330
PHILIPS CONSUMER ELETRONICS
Servizio Consumatori
Via Casati 26
20052 Monza - Milano
ITALY
PHILIPS INFO CENTER
Fegistrasse 5
8957 Spreitenbach
SUISSE
Tel.: 0844-800 544
Phone: 800 820026
PHILIPS Iberia, S.A.
C/Martinez Villergas, 49
28027 MADRID
PHILIPS MÁRKASZERVIZ
Kinizsi U 30-36
Budapest 1119
PHILIPS CUSTOMER CARE CENTER
Twee Stationsstraat 80/
80 Rue des Deux Gares
SPAIN
Phone: 902-113 384
HUNGARY
Phone: (01)-382 1700
1070 BRUSSEL/BRUXELLES
BELGIUM (for BENELUX)
Tel: 070-222 303
ΦΙΛΙΠΣ ΕΛΛAΣ AΕΒΕ
PHILIPS CONSUMENTENLIJN
25ΗΣ MAΡΤΙΟΥ 15
177 78 ΤAΥΡΟΣ
AΘΗΝA
t.a.v. betreffende afdeling
Postbus 102 5600 AC Eindhoven
NETHERLANDS
Τηλ. 0 0800 3122 1280
Phone: 0900-8406
www.philips.com
DVDR 80/051
|