ColorTV
Quick Use and Hookup Guide
IMPORTANT
CONTENTS
NOTE: This owner's manual is used with several differ-
ent television models. Not all features (and drawings)
discussed in this manual will necessarily match those
found with your television set. This is normal and does
not require that you contact your dealer or request serv-
ice.
Important Notice/Warning . . . . . . . . . . . . . . . . . . . .1
AV1 Input Jacks Connections . . . . . . . . . . . . . . . . .4
AV2 Input Jacks Connections . . . . . . . . . . . . . . . . .4
AV5 Input Jacks including DVI Connections . . . . .5
AV4 Input Jacks Connections . . . . . . . . . . . . . . . . .6
AV3 Side Input Jacks Connections . . . . . . . . . . . . .6
Component Video Input Jacks Connections . . . . . . .7
S-Video Input Connection . . . . . . . . . . . . . . . . . . . .7
Monitor Output Jack Connections . . . . . . . . . . . . . .8
Basic TV Operation . . . . . . . . . . . . . . . . . . . . . . . .1
Jack Panel Descriptions and Required Cables . . . . .1
Remote Battery Installation . . . . . . . . . . . . . . . . . . .2
Remote Control Button Descriptions . . . . . . . . . . . .2
Direct Cable TV Input Connection . . . . . . . . . . . . .3
Cable TV Box Input Connections . . . . . . . . . . . . . .3
Antenna TV Connection . . . . . . . . . . . . . . . . . . . . .3
WARNING: TO PREVENT FIRE OR SHOCK HAZ-
ARD DO NOT EXPOSE THIS UNIT TO RAIN OR
EXCESSIVE MOISTURE.
BASIC TV OPERATION
our television has a set of controls located on the top and
Yfront of the cabinet for use when the remote control is not
needed.
Press the POWER button on the front of the TV cabinet to
Volume and Channel buttons are located
on the top of the television cabinet.
turn the TV ON.
Note: With AutoChron ON, the TV will search for a PBS chan-
nel to set the clock before powering itself on. This can take sev-
eral seconds.
1
+
CHANNEL
+
–
VOLUME
–
Press the VOLUME + button to increase the sound level or
the VOLUME – button to lower the sound level.
Pressing both buttons at the same time will display the
onscreen menu. After you are in the menu, use these buttons to
make adjustments or selections.
2
Remote Sensor Window
Press the CHANNEL + or – button to select TV channels.
Use these buttons to make adjustments or selections in the
onscreen menu.
2
3
Audio, Video, S-Video
and Headphone Jacks
located on the side of
the television.
3
POWER
There is also a set of Audio and Video Input jacks located on the side
of the television cabinet. Refer to the Side AV3 Input section on page 6
of this Quick Use and Hookup Guide.
1
JACK PANEL DESCRIPTIONS AND REQUIRED CABLES
he television is equipped with external input and output jacks
Tfor use with optional accessory devices such as Home enter-
tainment Receivers, VCRs, DVD Player, Gaming Units, Video
Cameras, etc.
Located on the back of the TV
4
2
75Ω RF - Cable/Antenna Input connection jack.
HD1
HD2
5
1
AV 1 IN - Audio/Video connection jacks including
Component Video Inputs.
2
AV 2 IN - Audio/Video Input connection jacks including
S-Video connections.
7
3
6
AV 5 IN - High Definition 1080i or 480p Video, DVI
(Digital Video Input), Audio Inputs, Horizontal and Vertical
Sync connection jacks.
4
3
AV 4 IN - High Definition 1080i or 480p Video and Audio
Input connection jacks.
5
Monitor Out - Audio/Video Output connection jacks (TV
tuner signal only).
6
SIDE (AV 3) - Audio/Video Input jacks include a S-Video
jack, plus a Headphone jack located on the side of the cabi-
net.
Located on the side of the TV
7
1
A 75-ohm coaxial cable connects signals from an antenna or a
cable TV company to the antenna jack on the back of the TV.
Coaxial cables use “F” connectors.
A two-way signal splitter enables you to take a single antenna or
cable TV signal and supply it to two different inputs.
Video and audio cables with standard RCA (phono) connec-
tors connect the video and audio jacks of accessory devices
such as VCRs and DVD players to the jacks on the TV.
Yellow - Video
These connectors are usually color coded. The jacks on your
TV are also color coded to match the colors of the connectors.
Yellow for video (composite) and Red and White for the right
and left audio channels. The video cables used to connect com-
ponent video or RGB (high-resolution) jacks are color coded
red, green, and blue.
A 300- to 75-ohm twin-lead adapter accepts the antenna cables
(called twin-lead wires) from an antenna, allowing you to connect
the antenna signal to the TV.
White - Audio Left
Red - Audio Right
A S-Video cable provides better picture performance than regular
(composite) video connections.
S-Video cables can be used only with S-Video-compatible acces-
sory devices. You must also connect the left and right audio
cables to the AV 2 Audio in jacks because the S-Video jack car-
ries only the picture signal, not the sound.
A DVI (Digital Video) cable that will support digital connec-
tion from a PC. Only Single Digital Link DVI is supported for
PCs with 480p or 1080i output.
3121 233 44011
HOOKING UP THE TELEVISION
AC Power
Wall Outlet
Direct Cable
Connection:
DIRECT CABLE TV INPUT
HD1
HD2
our Cable TV input into your home may be a single (75
Yohm) cable or a converter box installation. In either
case, the connection to the TV is very easy. Follow the steps
below to connect your cable signal to your new television.
Cable signal coming from
Cable Company (Round
75Ω coaxial cable)
2
If your cable signal comes directly from a round 75Ω coaxial
cable use the following steps:
1
Connect the open end of the round Cable Company
supplied cable to the 75Ω input on the TV. Screw it down
finger tight.
1
2
Power Plug
from back of TV
Plug the television into the wall outlet and turn the TV
on. Refer to the AUTOPROGRAM feature to program all
the available channels on your cable signal.
Jack Panel
Back of TV
Cable Box Connection:
CABLE TV BOX INPUT
If your cable signal comes from a cable box, use the following
steps: (This connection will be mono. Some Cable boxes use
Left and Right channel audio output jacks for stereo connec-
tions. This type of Cable Box can be connected to the AV1 or
AV2 Audio Left and Right Audio Inputs. Please refer to your
Cable Box instructions.)
2
1
Jack Panel Back
of Cable Box
Cable Box
Power Cord
INPUT
OUTPUT
AC Power
Wall Outlet
Connect the open end of the round Cable Company
supplied cable to the cable signal IN(put) plug on the back
of the Cable Box.
HD1
HD2
Round 75Ω
Coaxial Cable
Jack Panel
Back of TV
1
Using a separate round coaxial cable, connect one end to
the OUT(put) plug on the back of the Cable Box.
4
2
Cable Signal IN from
the Cable Company
Connect the other end of the round coaxial cable to the
75Ω input on the back of the television. Screw it down fin-
ger tight.
3
3
Plug the television into the wall outlet and turn the TV
on. Refer to the TUNER and AUTOPROGRAM features
on page 4 of this Quick Use Guide. TUNER should be set
to the CABLE option. AUTOPROGRAM can be set to pro-
gram all the available channels on your cable signal into
the television’s memory.
4
The signal coming
from the box will
be MONO.
Power Plug
from back of TV
CABLE TV BOX WITH A/V INPUTS
This connection will supply Stereo sound to the TV.
Cable Signal IN
from the Cable
Company
Jack Panel Back
of Cable Box with A/V Outputs
Connect the open end of the round Cable Company sup-
plied cable to the cable signal IN(put) plug on the back of
the Cable Box.
1
2
Using a RCA type Video Cable, connect one end of the
cable to the Video (or ANT, your cable box may be labeled
differently) Out jack on the cable box and the other end to
the AV1 Video Input on the TV.
HD1
HD2
Audio Cables
L & R
(Red, White)
Video Cable
(Yellow)
Using a RCA type Audio Left and Right Cable, connect
one end to the left and right Audio Out L & R jacks on
the cable box. Connect the other end to the AV1 Audio L
& R Input jacks on the TV.
3
NOTE: Use the AV button on the TV remote control to tune to the
AV1 channel for the cable box signal. Once tuned, change chan-
nels at the cable box, not the television. Pressing the AV button
repeatedly will scroll all the AV Input channels, including the
presently tuned channel.
Jack Panel Back of TV
ANTENNA TV
combination antenna receives normal broadcast chan-
Anels (VHF 2–13 and UHF 14–69). Your connection is
easy because there is only one 75Ω (ohm) antenna plug on
the back of your TV, and that’s where the antenna goes.
Antenna Connection:
Outdoor or Indoor Antenna
(Combination VHF/UHF)
The combination antenna receives normal
AC Power
Wall Outlet
Jack Panel, Back of TV
broadcast channels 2-13 (VHF) and 14-69 (UHF).
If your antenna has a round cable (75 ohm) on the end,
then you're ready to connect it to the TV.
If your antenna has flat, twin-lead wire (300 ohm), you
first need to attach the antenna wires to the screws on a
300- to 75-ohm adapter.
HD1
HD2
1
300 to 75-ohm
Adapter
1
3
Push the round end of the adapter (or antenna) onto the
75Ω (ohm) plug on the back of the TV. If the round end of
the antenna wire is threaded, screw it down finger tight.
2
2
3
Twin
Lead Wire
Plug the television into the wall outlet and turn the TV
on. Refer to the TUNER and AUTOPROGRAM features on
page 4 of this Quick Use Guide. TUNER should be set to the
ANTENNA option. AUTOPROGRAM can be set to program
all the available channels on your cable signal into the televi-
sion’s memory.
Power Plug
from back
of TV
Round 75Ω Coaxial
Cable from Antenna
3
HOOKING UP THE TELEVISION
USING THE AV 1 INPUT JACKS
HD1
HD2
AV1
he TV’s audio/video input jacks are for direct picture and
Tsound connections between the TV and a VCR (or similar
device) that has audio/video output jacks. Follow the easy steps
below to connect your accessory device to the AV 1 Input Jacks
located on the back of the TV.
Connect the VIDEO (yellow) cable to the VIDEO AV1 IN
jack on the back of the TV.
1
1
2
Connect the AUDIO (red and white) cables to the
AUDIO (left and right) AV1 IN jacks on the rear of the TV.
2
Connect the VIDEO (yellow) cable to the VIDEO OUT
jack on the back of the VCR.
3
4
Connect the AUDIO (red and white) cables to the
AUDIO (left and right) OUT jacks on the rear of the VCR.
BACK OF TV
AUDIO IN
(RED/WHITE)
Turn the VCR (accessory device) and the TV ON.
5
VIDEO IN
(YELLOW)
Press the AV button on the remote control to tune the AV1
channel.
BACK OF VCR
6
7
Insert a prerecorded tape (or CD, DVD, depending on
the type of accessory device being used) and, press the
PLAY button on the accessory device to view the play-
back.
R
L
S-VIDO
UT
VIDEO
OUT
ANT/CABLE
AUDIO OUT
OUT
6
3
4
VCR
(EQUIPPED WITH VIDEO AND
AUDIO OUTPUT JACKS)
7
5
USING THE AV 2 INPUT JACKS
HD1
HD2
BACK OF TV
AV2
he TV’s audio/video input jacks allow you connect multiple
Taccessory devices at one time to different sets of input jacks..
Follow the easy steps below to connect an additional accessory
device to the AV 2 Input Jacks located on the back of the TV.
Connect the VIDEO (yellow) cable to the VIDEO AV2 IN
jack on the back of the TV.
1
1
2
Connect the AUDIO (red and white) cables to the
AUDIO (left and right) AV2 IN jacks on the rear of the TV.
2
Connect the VIDEO (yellow) cable to the VIDEO OUT
jack on the back of the VCR.
3
4
Connect the AUDIO (red and white) cables to the
AUDIO (left and right) OUT jacks on the rear of the VCR.
Turn the VCR (accessory device) and the TV ON.
5
R
L
S-VIDEO
OUT
VIDEO
OUT
ANT/CABLE
Press the AV button on the remote control to tune to the
AV2 channel.
AUDIO OUT
OUT
6
7
FIRST VCR
CONNECTED TO AV1 INPUTS
Insert a prerecorded tape (or CD, DVD, depending on
the type of accessory device being used) and, press the
PLAY button on the accessory device to view the play-
back.
6
VIDEO IN
(YELLOW)
AUDIO IN
(RED/WHITE)
R
L
S-VIDEO
UT
VIDEO
OUT
ANT/CABLE
OUT
AUDIO OUT
3
4
BACK OF 2ND VCR
5
7
SECOND VCR or ACCESSORY DEVICE
(EQUIPPED WITH VIDEO AND AUDIO OUTPUT JACKS)
4
HOOKING UP THE TELEVISION
USING THE AV 5 INPUT JACKS
Note: If the AV5 channel is tuned and no signal
connection present, the screen could jump or flash.
he AV5 Input Jacks provide High Definition Video Inputs at
T1080i or 480p, for accessories like a HD Receiver and Digital
DVD Players. There is also a DVI jack supplied allowing encrypt-
ed transmission of uncompressed HD content. .
JACK PANEL
ON BACK OF TV
1
HORIZONTAL
AND VERTICAL
SYNC CABLES
D1
HD2
2
Connect the Component (Y, Pb, Pr) Video OUT jacks
from the HD accessory device to the (Y, Pb, Pr) AV5
IN(put) jacks on the TV. If the device your using is
equipped with separate Horizontal and Vertical sync, con-
nect the H and V Outputs on the accessory device to the H
and V Inputs of AV5 IN.
DVI CABLE
1
AUDIO IN
(RED/WHITE)
3
Connect the red and white AUDIO CABLES to the Audio
(left and right) output jacks on the rear of the HD accessory
device to the Audio (L and R) AV5 IN(put) jacks on the TV.
COMPONENT
VIDEO
CABLES
2
Connect a DVI cable from the DVI OUT on the HD acces-
sory device to the AV5 DVI jack on the back of the TV.
3
4
4
Connect a 75Ω round cable from the OUT TO TV jack on
the HD accessory device to the 75Ω IN on the back of the
TV.
BACK of
ACCESSORY
DEVICE
1
If using a Satellite Dish, Cable signal or Antenna signal,
2
connect the 75Ω round cable from a Satellite Dish to the
5
SATELLITE IN and/or the Cable and Antenna signals to the
Y
Pb
L
R
R
Pr
ANTENNA “A” or “B” IN on the back of the HD accessory
device.
OMPONENT VIDEO
5
H
V
S-VIDEO
DIGITAL AUDIO
OUTPUT
VCR
CONTROL
AUDIO
VIDEO
SYNC OUT
SATELLITE
IN
ANTENNA B
IN
ANTENNA A
IN
OUT TO TV
PHONE JACK
Press the AV button on the remote control repeatedly to
tune to the AV5 channel.
6
Your now ready to use your digital device to begin playback of
high definition quality.
COAXIAL CABLE
LEAD-IN FROM
SATELLITE DISH
COAXIAL CABLE
LEAD-IN FROM
ALTERNATE RF
SIGNAL SOURCE
5
5
COAXIAL CABLE
LEAD-IN FROM CABLE
OUTLET, CONVERTER BOX,
OR VHF/UHF ANTENNA
NOTE: This television is designed to accept high definition sig-
nals 1080i and 480p as specified by the Electronic Industries
Association standard EIA770.3. Digital devices from different
manufacturers have the possibility of differing output standards
which my cause difficulties for the television to properly dis-
play.
AV5
c
CHECK IT OUT
DVI - DVI is a specific digital input allowing encrypted trans-
mission of uncompressed HD content. DVI includes HDCP
(high-bandwidth digital content protection), which is supported
by Hollywood, satellite providers, and most of the consumer
electronics industry. DVI is gaining momentum and quickly
becoming an industry standard for the consumer to view high-
definition material while keeping content protected.
NOTE: The Picture-in-Picture (PIP) feature is not available for
use with AV5.
6
5
HOOKING UP THE TELEVISION
Note: If the AV4 channel is tuned and no signal con-
nection present, the screen could jump or flash.
USING THE AV 4 INPUT JACKS
JACK PANEL
ON BACK OF TV
he AV4 Input Jacks provide High Definition Video Inputs at
T1080i or 480p, for accessories like a HD Receiver and Digital
DVD Players. Using the color difference signals (Pb, Pr) and the
luminance (Y) signal will improve color bandwidth information.
1
HD1
HD2
AV4
2
Connect the Component (Y, Pb, Pr) Video OUT jacks
from the DVD player (or similar device) to the (Y, Pb, Pr)
AV4 IN(put) jacks on the TV.
1
2
Connect the red and white AUDIO CABLES to the
AUDIO (left and right) OUT(put) jacks on the rear of the
accessory device to the Audio (L and R) AV4 IN(put) jacks
on the TV.
Press the AV button on the remote control repeatedly to
tune to the AV4 channel.
3
Turn the TV and the DVD (or digital accessory device)
ON.
4
Press the PLAY button on the DVD (or digital accessory
device) to view the program on the television.
AUDIO IN
(RED/WHITE)
COMPONENT
VIDEO
CABLES
5
COMP VIDEO
S-VIDEO
VIDEO
OUT
AUDIO
NOTE: This television is designed to accept high definition sig-
nals 1080i and 480p as specified by the Electronic Industries
Association standard EIA770.3. Digital devices from different
manufacturers have the possibility of differing output standards
which my cause difficulties for the television to properly display.
Y
Pb
R
OUT
L
OUT
Pr
2
3
1
JACK PANEL
OF DIGITAL DEVICE SUCH
AS A DVD PLAYER
EQUIPPED WITH
COMPONENT VIDEO
OUTPUTS
5
4
USING THE SIDE AV 3 INPUT JACKS
SIDE (AV 3) Input Jacks
Located on the Side of
the Television Cabinet
AV3
his television has input jacks conveniently located on the side
Tof the cabinet. These jack are for easy hook-ups (without hav-
ing to move around to the back of the TV) for cameras, gaming
units, and other accessory devices that wouldn’t be connected
permanently. Follow the easy steps below to connect your acces-
sory device to the SIDE Input Jacks located on the right side of
the TV.
AV3
Connect the VIDEO (yellow) cable to the VIDEO IN jack
on the side of the TV.
1
Connect the AUDIO (red and white) cables to the
AUDIO (left and right) IN jacks on the side of the TV.
2
Connect the VIDEO (yellow) cable to the VIDEO OUT
jack on the back of the camera (or accessory device).
3
4
1
Connect the AUDIO (red and white) cables to the
AUDIO (left and right) OUT jacks on the rear of the cam-
era (or accessory device).
Turn the camera (or accessory device) and the TV ON.
2
5
VIDEO IN
(YELLOW)
Press the AV button on the remote control repeatedly to
tune to the AV3 channel.
AUDIO IN
(RED &
WHITE)
6
The SIDE
JACKS also
contain a
HEADPHONE
JACK.
With the camera (or accessory device) ON and a prere-
corded tape (or other media depending on type of accesso-
7
3
4
6
ry device being used) inserted, press the PLAY button to
view the tape on the television.
Jack Panel of
Camera
or External
AUDIO
LEFT RIGHT
VIDEO
Accessory Device
S-VIDEO
NOTE: The S-Video Cable can be used in place of the Yellow
Video cable shown in this diagram. If your camera or accessory
device has a S-Video output jack, connecting the video signal
through the S-Video jack will reproduce the video signal with
greater quality.
7
5
6
HOOKING UP THE TELEVISION
HD1
HD2
COMPONENT VIDEO INPUT (CV1)
BACK OF TV
f using an accessory device that is not high definition but uses
IComponent Video jacks. The AV1 jacks on the TV offer the user
the possibility of better video reproduction using the Component
Video Inputs. The color difference signals (Pb, Pr) and the lumi-
nance (Y) signal are connected and received separately, which
allows for improved color bandwidth information (not possible
when using composite video or S-Video connections).
CVI
1
2
Connect the Component (Y, Pb, Pr) Video OUT jacks
from the DVD player (or similar device) to the (Y, Pb, Pr)
1
IN(put) jacks on the TV. When using the Component Video
Inputs, it is best not to connect a signal to the AV1 Video
Input.
Connect the yellow VIDEO CABLE along with the red
and white AUDIO CABLES to the AUDIO (left and
right) OUT(put) jacks on the rear of the accessory device
to the AV1 VIDEO and AUDIO IN(put) jacks on the TV.
2
Press the AV button on the remote control repeatedly to
tune to the CVI channel.
3
AUDIO IN
(RED/WHITE)
COMPONENT
VIDEO
CABLES
Turn the TV and the DVD (or digital accessory device)
ON.
4
COMP VIDEO
S-VIDEO
OUT
AUDIO
VIDEO
OUT
Insert a DVD disc into the DVD player and press the
PLAY ᮣ button on the DVD Player (or digital accesso-
ry device).
Y
Pb
Pr
R
L
5
OUT
1
VIDEO
(YELLOW)
CABLE
HELPFUL HINT
2
The description for the component video connectors may differ
depending on the DVD player or accessory digital source
equipment used (for example, Y, Pb, Pr; Y, B-Y, R-Y; Y, Cr,
Cb). Although abbreviations and terms may vary, the letters b
and r stand for the blue and red color component signal con-
nectors, and Y indicates the luminance signal. Refer to your
DVD or digital accessory owner’s manual for definitions and
connection details.
3
ACCESSORY DEVICE
EQUIPPED WITH
COMPONENT VIDEO
OUTPUTS.
5
4
S-VIDEO INPUT
HD1
HD2
AV2
JACK PANEL
ON BACK OF TV
he S(uper)-Video connection on the rear of the TV can provide
Tyou with better picture detail and clarity for the playback of
accessory sources such as DBS (digital broadcast satellite), DVD
(digital video discs), video games, and S-VHS VCR (video cas-
sette recorder) tapes than the normal antenna picture connec-
tions.
NOTE: The accessory device must have an S-VIDEO OUT(put)
jack in order for you to complete the connection on this page.
Connect the S-VIDEO CABLE to the S-VIDEO input jack
on the rear of the television.
2
1
1
Connect the AUDIO (red and white) cables to the AUDIO
AV2 IN jacks on the rear of the TV
.
2
3
4
Connect the S-VIDEO CABLE to the S-VIDEO
OUT(put) jack on the accessory device.
Connect the red and white AUDIO cables to the AUDIO
(left and right) OUT(put) jacks on the rear of the accessory
device.
AUDIO CABLES
(Red & White)
When using the S-Video Input, do not
connect a video signal to the AV 2 IN
Video Jack. This could cause a ghost
image to appear over the S-Video signal.
S-VIDEO
CABLE
Press the AV button on the remote control repeatedly to
tune the AV2 channel. The S-Video Input is dominate over
the AV2 Video Input.
5
Turn the VCR, DVD or other accessory device ON.
L
R
VIDEO
OUT
S-VIDEO
OUT
ANTABLE
OUT
AUDIO OUT
6
7
5
With the VCR (or accessory device) ON and a prerecorded
tape inserted, press the PLAY button to view the tape on
the television.
3
7
4
c
CHECK IT OUT
The S-Video jack and the AV 2 jacks work together. When a
device is connected to the S-Video jack, do not connect a signal to
the AV 2 IN Video jack. This could cause an over-lapping of two
video images on the TV screen.
VCR or EXTERNAL
ACCESSORY DEVICE
WITH S-VIDEO OUTPUT
6
7
HOOKING UP THE TELEVISION
MONITOR OUTPUT JACKS
SECOND VCR FOR RECORDING
HD1
HD2
JACK PANEL
Located on the
back of the TV
he Audio/Video (Monitor) Output jacks can be used for
Trecording a selected TV (Antenna Input/tuner signal source)
Channel. This recording can even be completed while viewing
another external Audio/Video Source Select option. (For example:
DVD program playback shown through the A/V 1 or 2 Input
source connection.)
MONITOR OUT
VIDEO &
AUDIO L(eft) and R(ight)
NOTE: Refer to page 4 for the proper hookup of an accessory
device to the AV 1 IN(put) jacks. Follow the instructions on how
to tune to the AV 1 channel to view a DVD program playback or
pre-recorded VCR tape.
1
The following steps allow you to connect a VCR to record a
selected TV channel program through the Monitor Outputs.
Connect one end of the yellow Video Cable to the
Monitor Out VIDEO plug. Connect the other end to the
VIDEO IN plug on the VCR.
1
2
3
VIDEO CABLE
(Yellow)
AUDIO CABLES
(Red & White)
3
4
Connect one end of the red and white Audio cable from
the Monitor Out AUDIO L and R plugs on the TV to the
AUDIO IN plugs on the VCR.
2
COMP VIDEO
AUDIO
S-VIDE
O
VIDEO
OUT
ANTENNA
OUT
IN
OUT
AUDIO
IN
L
Y
Pb
Pr
Tune the TV to the program channel you wish to record
by pressing the AV or NUMBERED buttons.
L
R
ANTENNA
OUT
VIDEO
OUT
R
IN
Note: Once selected be sure to leave the TV channel tuned
to the desired program until the complete recording is fin-
ished.
AV 1 Sample DVD
(accessory device
Hookup from Page 4)
Recording
VCR
Turn the recording VCR ON, insert a blank VHS tape
and it’s ready to record the channel program you selected
previously in step #3.
4
MONITOR OUTPUT JACKS
EXTERNAL AUDIO SYSTEM
HD1
JACK PANEL
Located on the
back of the TV
HD2
he Audio Output jacks are great for connecting to an external
Taudio system or a set of external speakers. This will enhance
the sound coming from the television to improve your viewing and
listening experience.
For Audio System Connection:
Connect one end of the R(ight) and L(eft) Audio Cables
(red and white) to the AUDIO OUT (Left and Right) jacks
on the television.
1
1
Connect the other ends of the R(ight) and L(eft) Audio
Cables (red and white) to the Audio Left and Right Input
jacks on the external Audio System.
2
3
4
4
Turn the Audio System and the TV on. Adjust the vol-
ume coming from the Audio System to a pleasant listening
level.
You can now adjust the sound level coming from the audio
system by pressing the VOLUME (+) or (–) button on
the TV or remote control.
AUDIO CABLES
(Red & White)
2
R
L
AUX/TV INPUT
PHONO INPUT
3
EXTERNAL
AUDIO SYSTEM
8
|