Register your product and get support at
21PT8439/94
21PT3429/94
EN User manual
Risk of injury or damage to the TV!
1 Important
•
Two people are required to lift and carry
a TV that weighs more than 25 kg.
If the TV is transported in temperatures
below 5°C, unpack the TV and wait
until the TV temperature matches room
temperature before connecting the TV to
the power outlet.
•
Read and understand all instructions before you
use yourTV. If damage is caused by failure to
follow instructions, the warranty does not apply.
•
Before you connect the TV to the power
outlet, ensure that the power voltage
matches the value printed on the back
of the TV. Never connect the TV to the
power outlet if the voltage is different.
Safety
Risk of electric shock or fire!
•
Never expose the TV to rain or water.
Never place liquid containers, such as
vases, near the TV. If liquids are spilt on
or into the TV, disconnect the TV from
the power outlet immediately. Contact
Philips Consumer Care to have the TV
checked before use.
Risk of injury to children!Follow these
precautions to prevent the TV from toppling
over and causing injury to children:
•
Never place the TV on a surface covered
by a cloth or other material that can be
pulled away.
Ensure that no part of the TV hangs over
the edge of the surface.
Never place the TV on tall furniture (such
as a bookcase) without anchoring both
the furniture and TV to the wall or a
suitable support.
•
Never place the TV, remote control or
batteries near naked flames or other heat
sources, including direct sunlight.
To prevent the spread of fire, keep
candles or other flames away from the
TV, remote control and batteries at all
times.
•
•
•
Educate children about the dangers of
climbing on furniture to reach the TV.
Risk of overheating!
•
Never install the TV in a confined space.
Always leave a space of at least 4 inches
or 10 cm around the TV for ventilation.
Ensure curtains or other objects never
cover the ventilation slots on the TV.
•
Never insert objects into the ventilation
slots or other openings on the TV.
Risk of injury, fire or power cord damage!
Risk of short circuit or fire!
•
Never place the TV or any objects on the
power cord.
To easily disconnect the TV power cord
from the power outlet, ensure that you
have full access to the power cord at all
times.
•
Never expose the remote control or
batteries to rain, water or excessive heat.
Avoid force coming onto power plugs.
Loose power plugs can cause arcing or
fire.
•
•
•
•
When you disconnect the power cord,
always pull the plug, never the cable.
Disconnect the TV from the power outlet
and aerial before lightning storms. During
lightning storms, never touch any part of
the TV, power cord or aerial cable.
Screen care
Disposal of your old product and
batteries
•
Avoid stationary images as much as
possible. Stationary images are images
that remain on-screen for extended
periods of time. Examples include:
on-screen menus, black bars and time
displays. If you must use stationary
images, reduce screen contrast and
brightness to avoid screen damage.
Unplug the TV before cleaning.
Clean the TV and frame with a soft,
damp cloth. Never use substances such as
alcohol, chemicals or household cleaners
on the TV.
Risk of damage to the TV screen! Never
touch, push, rub or strike the screen with
any object.
To avoid deformations and colour fading,
wipe off water drops as soon as possible.
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
•
•
When this crossed-out wheeled bin symbol
is attached to a product it means that the
product is covered by the European Directive
2002/96/EC. Please inform yourself about the
local separate collection system for electrical
and electronic products.
Please act according to your local rules and
do not dispose of your old products with your
normal household waste.
•
•
Correct disposal of your old product helps to
prevent potential negative consequences for
the environment and human health.
Your product contains batteries covered by
the European Directive 2006/66/EC, which
cannot be disposed with normal household
waste.
Please inform yourself about the local rules
on separate collection of batteries because
correct disposal helps to prevent negative
consequences for the environmental and
human health.
a
(Standby-On)
Switches the TV to standby if it is on.
Switches on the TV if it is in standby.
2 Your product
•
•
b Not used.
Congratulations on your purchase, and
welcome to Philips!To fully benefit from the
support that Philips offers; register your product
c
INFO
Displays programme information, if available.
d Not used.
INCR. SURR (Used only in some models)
e
Enables Incredible Surround for stereo
sources. Enables spatial mode for mono
sources.
Product overview
This section gives you an overview of
commonly used controls and functions.
f Not used.
g
h
i
(Navigation buttons)
Navigates through the menus.
Remote control
SMART (Smart picture)
Cycles through pre-defined picture settings.
1
2
(Mute)
Mutes or restores audio output.
19
18
17
3
4
5
j CH +/- (Channel +/-)
Switches to the next or previous channel.
k 0-9 (Numeric buttons)
6
7
Selects a channel or setting.
l A/CH (Alternative channel)
Toggles between the current channel and the
last viewed channel.
8
9
16
m AV
Selects connected devices.
15
14
10
n DUAL
Switches from Stereo to Mono.
o VOL +/- (Volume +/-)
11
Increases or decreases volume.
p
SMART (Smart Sound)
Cycles through pre-defined sound settings.
12
13
q MENU
Toggles the main menu on or off.
r Not used.
s
TIMER
Sets the timers.
c CVI
Video input from analogue devices such
Controls and indicators
as DVD, receiver, game console, etc. This
connector is used with audio input.
d TV ANTENNA
Signal input from an antenna, cable or
satellite.
+
-
POWER
VOLUME
CHANNEL
e
d
c b
a
Side connectors
a
POWER: Switches the product on or
off.
b Remote control sensor
c Standby indicator
d CHANNEL / : Switches to the next
or previous channel.
e VOLUME +/-: Increases or decreases
volume.
a VIDEO
Back connectors
Composite video input from analogue
devices such as VCRs.
b AUDIO L/R
Audio input from analogue devices
connected to VIDEO.
ANT
AV out AV in
CVI
a AV OUT
Audio and video output to analogue
devices such as another TV or a recording
device.
b AV IN (VIDEO and AUDIO L/R)
Analogue audio and video input from
analogue or digital devices such as DVD
players, satellite receivers and VCRs.
Connect a video recorder:
3 Get started
AV sockets on the rear of the TV
VIDEO
L/Mono
Connect devices
AUDIO
R
AV out
AV in
CVI
This section describes how to connect various
devices with different connectors.
Note
• Different types of connectors may be used to
connect a device to your TV, depending on
availability and your needs.
VCR with Video and Audio input sockets
Connect devices
Connect a video player:
AV sockets on the rear of TV
Connect a video recorder and a set-top box:
Sockets on the rear of the TV
ANT
AV out AV in
CVI
AV in
Set top box
VCR with Video and Audio output sockets
Insert remote control
batteries
Skip channels
4 Install channels
1 Press MENU.
2 Select [INSTALL] > [MANUAL STORE]
Automatically install channels
> [SKIP].
3 Select [ON] to skip channel.
Note
4 Press INFO to exit.
• Make sure that the TV is in TV mode.
• Press AV repeatedly until the channel number
appears.
Swap channels
1 Press MENU.
1 Press MENU.
2 Select [INSTALL] > [AUTO STORE] .
3 Press to start the automatic search.
4 Press MENU to exit.
2 Select [INSTALL] > [CHANNEL SWAP]
> [FROM].
3 Select
enter the channel number.
4 Press to select [To].
5 Press or the numeric buttons to key
in the channel number.
6 Press to select [EXCHANGE].
7 Press to exchange the programs of
the two channels.
or the numeric buttons to
Manually install channels
Note
• Make sure that the TV is in TV mode.
• Press AV repeatedly until the channel number
appears.
8 Press INFO to exit.
1 Press MENU.
2 Select [INSTALL] > [MANUAL STORE]
Select the colour and sound
system
> [CHANNEL].
3 Press the numeric buttons to enter the
channel number.
1 Press MENU.
4 Press to select [SEARCH].
5 Press to start the manual search.
6 Press MENU to exit.
2 Select [INSTALL] > [MANUAL STORE]
> [COLOUR SYS].
3 Select
4 Press to select [SOUND SYS].
5 Press to select your sound system.
6 Press INFO to exit.
to select your colour system.
Fine tune channels
1 Press MENU.
2 Select [INSTALL] > [MANUAL STORE]
> [FINE TUNE].
3 Press
to adjust.
4 Press INFO to exit.
Switch channels
5 Use your
product
This section helps you perform basic operations
(see ‘Use more of your product’ on page 11).
Switch yourTV on/off or to
standby
•
•
Press CH +/- on the remote control
or at the front of theTV.
Enter a channel number using the
/
To switch on
•
If the standby indicator is off, press at
the front of the TV.
Numeric buttons.
•
If the standby indicator is red, press on
the remote control.
To switch to standby
Watch connected devices
•
Press on the remote control.
» The standby indicator switches to red.
Use the source button
To switch off
Press at the front of the TV.
•
» The standby indicator switches off.
Press AV repeatedly to cycle through the
various sources.
Tip
AdjustTV volume
• Though your TV consumes very little power
when in standby, energy continues to be
consumed. When not in use for an extended
period of time, disconnect the TV power cable
from the power outlet.
To increase or decrease volume
•
•
Press VOL +/-.
Press +/- at the front of the TV.
To mute or unmute sound
•
•
Press to mute the sound.
Press again to restore the sound.
Use smart picture
6 Use more of
your product
Use smart picture to apply pre-defined
picture settings.
AccessTV menus
Menus help you to install channels, change
picture and sound settings and access other
features.
1 Press SMART repeatedly to cycle
through the four settings.
•
[PERSONAL]Settings are set to your
preference.
1 Press MENU.
» The menu screen appears.
•
[SOFT]Emphasises warm colours.
This setting is suitable for watching
TV programmes in dimly lit rooms.
[NATURAL]Emphasises original
colours.
[RICH]Emphasises vibrant colours.
This is suitable for watching TV
programmes in brightly lit rooms.
MAIN
•
•
PICTURE
SOUND
BRIGHTNESS
COLOUR
FEATURES
INSTALL
CONTRAST
SHARPNESS
2 Press to exit.
COLOURTEMP
CONTRAST +
Manually adjust picture settings
1 Press MENU.
2 Press the navigation buttons to enter the
2 Press the
to select and navigate
through one of the following menus.
[PICTURE] menu.
3 Press
to select from the following
settings and adjust:
•
[PICTURE]Adjusts the picture
setting for optimal viewing.
[SOUND]Adjusts the sound setting.
[FEATURES]Accesses features.
[INSTALL]Selects the channel
installation menu.
•
•
•
[BRIGHTNESS]Adjusts the intensity
and details of dark areas.
[COLOUR]Adjusts colour
saturation.
[CONTRAST]Adjusts the intensity
of bright areas, keeping dark areas
unchanged.
•
•
•
3 Press MENU to return to the previous
menu.
•
•
•
[SHARPNESS]Adjusts the sharpness
of an image.
[COLOUR TEMP]Adjusts the
orange or blue tones in a picture.
[CONTRAST +]Select ON to
optimise the picture contrast for
enhanced picture quality.
Change picture and sound
settings
Change picture and sound settings to suit your
preferences.You can apply pre-defined settings
or change settings manually.
Use smart sound
Use timers
Use smart sound to apply pre-defined sound
settings.
You can set timers to switch theTV to standby
at a specified time.
Set the time
1 Press MENU.
2 Select [FEATURES] > [TIMER] >
1 Press SMART repeatedly to cycle
[CLOCK].
through the four settings.
3 Press
confirm.
4 Press
to confirm.
to set the hour and press to
•
•
•
•
[PERSONAL]Settings are set to your
preference.
[VOICE]Emphasises high tones
(treble boosted).
[THEATRE]Emphasises sensation to
action (bass and treble boosted).
[MUSIC]Emphasises low tones (bass
boosted).
to set the minutes and press
5 Press MENU to exit.
Set timer options
2 Press to exit.
1 Press MENU.
2 Select [FEATURES] > [TIMER] .
Note
3 Press
to select from the following
• Smart sound is available only in some models.
options and adjust:
•
[ON TIME]Sets a time for the TV to
turn on from standby.
•
[ON CHANNEL]Sets the channel
that is displayed when the TV is
turned on from standby.
[OFF TIME]Sets a time for the TV to
turn off to standby.
[SLEEP TIME]Sets a delay (in
minutes) after which the TV is
turned off to standby.
[CH SWITCH]Sets a time for the
TV to switch to another channel.
[SWITCH TO]Sets a channel
to switch to when the TV is
programmed to switch to another
channel.
Adjust sound settings
1 Press MENU
•
•
2 Press the navigation buttons to enter the
[SOUND] menu.
3 Press
to select from the following
settings and adjust:
•
•
•
[TREBLE]Adjusts the treble level.
[BASS]Adjusts the bass level.
[BALANCE]Adjusts the balance of
the right and left speakers to best
suit your listening position.
•
•
•
[SURROUND]Enables spatial sound.
4 Press MENU to exit.
Note
• Some of the sound settings may not be
available in some models.
•
•
Loudspeakers, unearthed audio devices,
neon lights, high buildings and other large
objects can influence reception quality. If
possible, try to improve the reception quality
by changing the antenna direction or moving
devices away from the TV.
7 Troubleshooting
This section describes commonly encountered
issues and accompanying solutions.
If reception on only one channel is poor, fine
tune this channel.
There is poor picture quality from connected
devices:
GeneralTV issues
•
Check that the devices are connected
properly.
TheTV does not switch on:
•
Check that the picture settings are correctly
set.
•
Disconnect the power cable from the
power outlet. Wait for one minute then
reconnect it.
Check that the power cable is securely
connected.
•
Sound issues
The remote control is not working properly:
•
Check that the remote control batteries
are correctly inserted according to the
+/- orientation.
There is a picture but sound quality is poor:
•
•
•
Check that all cables are properly connected.
Check that the volume is not set to 0.
Check that the sound is not muted.
•
•
Replace the remote control batteries if
they are flat or weak.
Clean the remote control and TV sensor
lens.
There is a picture but the sound quality is poor:
•
Check that the sound settings are correctly
set.
The standby light on theTV blinks red:
•
There is a picture but sound comes from one
speaker only:
Disconnect the power cable from the
power outlet. Wait until the TV cools
down before reconnecting the power
cable. If the blinking reoccurs, contact
Philips Consumer Care.
•
Verify that sound balance is set to the centre.
When turning theTV on/off/to standby, you
hear a creaking sound from theTV chassis:
Contact us
•
No action is required. The creaking sound
is normal expansion and contraction of
the TV as it cools down and warms up.
This does not impact performance.
If you cannot resolve your problem, refer to the
the problem remains unresolved, contact Philips
Consumer Care in your country.
Picture issues
Warning
• Do not attempt to repair the TV yourself. This
may cause severe injury, irreparable damage to
your TV or void your warranty.
TheTV is on, but there is no picture:
•
Check that the antenna is properly
connected to the TV.
•
Check that the correct device is selected
as the TV source.
Note
There is sound but no picture:
•
Check that the picture settings are
correctly set.
• Make a note of your TV model and serial
number before you contact Philips. These
numbers are printed on the back of the TV
and on the packaging.
There is poorTV reception from an antenna
connection:
•
Check that the antenna is properly
connected to the TV.
8 Product
information
Product information is subject to change
without notice. For detailed product
Picture
Diagonal screen size: 54 cm
Visible diagonal screen size: 51cm
Tuner/Reception/
Transmission
•
•
•
Antenna input: 75 ohm coaxial
TV system: PAL, BG
Video playback: NTSC, PAL
Remote control
•
Batteries: 2 x AAA (LR03 type)
Connections
•
•
•
•
•
CVI
AV in
AV out
Antenna
Side Video in and Audio in L/R
Power
•
•
Mains power: AC 110-240 V, 50-60 Hz
Power consumption: 72 W
Compliance with EMF
9 Notice
Koninklijke Philips Electronics N.V. manufactures
and sells many products targeted at consumers
which, like any electronic apparatus, in
general have the ability to emit and receive
electromagnetic signals.
2009 © Koninklijke Philips Electronics N.V.All
rights reserved.
Specifications are subject to change without
notice.Trademarks are the property of
Koninklijke Philips Electronics N.V. or their
respective owners. Philips reserves the right
to change products at any time without being
obliged to adjust earlier supplies accordingly.
The material in this manual is believed
adequate for the intended use of the system.
If the product, or its individual modules or
procedures, are used for purposes other than
those specified herein, confirmation of their
validity and suitability must be obtained. Philips
warrants that the material itself does not
infringe any United States patents. No further
warranty is expressed or implied.
One of Philips’ leading Business Principles is to
take all necessary health and safety measures
for our products, to comply with all applicable
legal requirements and to stay well within
the EMF standards applicable at the time of
producing the products.
Philips is committed to develop, produce and
market products that cause no adverse health
effects. Philips confirms that if its products are
handled properly for their intended use, they
are safe to use according to scientific evidence
available today.
Philips plays an active role in the development
of international EMF and safety standards,
enabling Philips to anticipate further
developments in standardisation for early
integration in its products.
Philips cannot be held responsible either for any
errors in the content of this document or for
any problems as a result of the content in this
document. Errors reported to Philips will be
corrected and published on the Philips support
website as soon as possible.
Copyright
All other registered and unregistered
trademarks are the property of their respective
owners.
Warranty
No components are user serviceable. Do not
open or remove covers to the inside of the
product. Repairs may only be done by Philips
Service Centres and official repair shops. Failure
to do so shall void any warranty, stated or
implied.
Any operation expressly prohibited in
this manual, any adjustments, or assembly
procedures not recommended or authorised in
this manual, shall void the warranty.
© 2009 Koninklijke Philips Electronics N.V.
All rights reserved.
Document order number: 0764-21U12000-03
|