AQU5611D BK
AQU5611DT BK 9.2 million pixels
Color TFT LCD Monitor
USER MANUAL
P/N: 55P1003
Danger Statements
DANGER
To avoid shock hazard:
v Do not remove the covers.
v Do not operate this product unless the stand is attached.
v Do not connect or disconnect this product during an electrical storm.
v The power cord plug must be connected to a properly wired and grounded power
outlet.
v Any equipment to which this product will be attached must also be connected to
properly wired and grounded power outlets.
v To isolate the monitor from the electrical supply, you must remove the plug from
the power outlet. The power outlet should be easily accessible.
Handling:
v
Your color monitor is heavy, so handle it with care. iiyama recommends that this
monitor is moved or lifted by two people.
iii
iv AQU5611D BK/AQU5611DT BK 9.2 Million Pixels Color TFT LCD Monitor USER MANUAL
Notices
Attention
v Do not exert strong pressure to the surface of the monitor screen. You may break
the LCD panel.
v Do not place heavy objects on top of this product. They may damage the
monitor.
v Do not touch the monitor screen with your fingers. Fingerprints and oil stains may
remain on the screen surface. They are difficult to wipe off.
v The monitor is heavy. Ask the help of others if you cannot carry it by yourself.
v When leaving your office for a long vacation, always unplug the power cords
from the main outlet.
LCD considerations
The liquid crystals in the display panel contain several irritants. If the panel is
damaged or broken, do not let the liquid come in contact with your skin, eyes, or
mouth. If you do come in contact with the liquid, flush the affected part with running
water for at least 15 minutes. If any symptom remains, consult a doctor.
The fluorescent lamp in the liquid crystal display (LCD) contains mercury (50 mg.
(0.002 oz.) maximum). Do not place in trash that is disposed of in landfills. Dispose
of it as required by local ordinances or regulations.
Considerations on the monitor resolution
This monitor is able to display characters, graphics, and pictures at high resolution.
When you connect this monitor to a PC with a high resolution (3840 x 2400), the
characters will be displayed at 1/4 the normal size. Do not continue to operate the
PC at this character size. You can spoil your eyes. Change the character size to a
bigger size or the resolution to a lower resolution on the operating system or
application.
Operating considerations
To ensure comfortable operation of the monitor, follow the instructions below:
v Place the monitor in front of you for easy viewing.
v Place the monitor at a comfortable distance (50 –60 cm) (19 – 24 in.) from you.
v Tilt the monitor so that top of the monitor is at your eye level.
v Adjust the angle of the tilt so that there is no reflection of light and objects. If
necessary, turn off the light or lower its luminescence. If near a window, close the
curtains or pull down the blind to cut the sunlight.
v Adjust the screen brightness.
v Use a chair with a high-reclining and sit deep into it.
v Operating on the screen for long hours can cause fatigue and eyestrain. Divert
your eyes from the screen for short intervals during operation, and take short
rests.
v
License inquiries
References in this publication to iiyama products, programs, or services do not
imply that iiyama intends to make these available in all countries in which iiyama
operates. Any reference to an iiyama product, program, or service is not intended to
state or imply that only iiyama product, program, or service may be used. Any
functionally equivalent product, program, or services that does not infringe on any of
the intellectual property rights of iiyama may be used instead of the iiyama product,
program, or services. The evaluation and verification of operation in conjunction
with other products, except those expressly designated by iiyama, are the
responsibility of the user.
iiyama may have patents or patents pending which covers the subject matter in this
document. The furnishing of this document does not give you any license to these
patents. You can send license inquiries, in writing, to:
IIYAMA CORPORATION
710-1 Kitaowaribe,
Nagano-shi, 381–0014
Japan
Trademarks
iiyama logo is a registered trademark of IIYAMA CORPORATION.
ATI is a registered trademark of ATI Technologies, Inc., in the United States or other
countries, or both. FireGL is trademark of ATI Technologies, Inc.
TMDS is a trademark of Silicon Image, Inc., in the United States or other countries,
or both.
Windows is registered trademark of Microsoft Corporation, in the United States or
other countries, or both.
vi AQU5611D BK/AQU5611DT BK 9.2 Million Pixels Color TFT LCD Monitor USER MANUAL
Contents
vii
viii AQU5611D BK/AQU5611DT BK 9.2 Million Pixels Color TFT LCD Monitor USER MANUAL
Chapter 1. Before setting up
This manual contains information on how to set up and operate the AQU5611D
BK/AQU5611DT BK 9.2 Million Pixels Color TFT LCD Monitor, hereafter called the
monitor.
This chapter describes the following:
v Prerequisites
v Unpacking
v Checking parts
Prerequisites
Unpacking
You will need a personal computer or a workstation (hereafter called the computer)
with the following.
v A Dual DVI output compliant video graphics card (hereafter simply called the
DVI)
responsible for any damages incurred by the installation of unsupported cards.
Attention: The monitor is heavy. Be careful not to drop it. The LCD is fragile and
should not be bumped on an edge, or dropped.
Open the carton box and carefully remove the monitor. Hold the bottom of the
screen firmly with both hands, as shown below.
1
Checking parts
Check the box for the following items. If any items are missing or damaged, contact
your place of purchase immediately.
h Monitor
h USER MANUAL
(This book)
h Connector tool
h Power adapter and cord
h Digital signal cable
P/N: 07N2227
h Power cord
Note: The digital signal cable is shipped with one end connected to the monitor.
2
AQU5611D BK/AQU5611DT BK 9.2 Million Pixels Color TFT LCD Monitor USER MANUAL
Chapter 2. Hardware setup
This chapter describes the following:
v The location of the controls, switches, and connectors.
v The procedure for setting up the monitor.
Locations
Front view
Monitor screen
OSD control
Serial number label
Brightness control
Power switch
Base stand
Power light
(Power on/Standby)
Rear view
DC-IN connector
Video connector
Connector cover
Security keyhole
Stand rear cover
Cable hook
Cable clamp
3
Setup the monitor
Storing the connector tool
This section describes how to store the connector tool for future use. This tool will
be useful when disconnecting the cables from the monitor.
Attention:
1. Remove any objects from the surface before tilting the monitor. They might
damage your screen.
2. Be careful not to pinch your fingers between the monitor and the surface when
tilting the monitor.
To store the connector tool, do the following:
1. Clear a work space, and turn the monitor face down.
2. Remove the stand rear cover.
Stand rear cover
4
AQU5611D BK/AQU5611DT BK 9.2 Million Pixels Color TFT LCD Monitor USER MANUAL
Connecting the cables
This section describes how to connect the following cables:
1. Power adapter cord
2. Digital signal cable
3. Power cord
Connecting the power adapter cord
1. Connect the power adapter cord to the DC-IN connector at the rear of the
monitor. Make sure that it clicks firmly into the connector.
Video connector
DC-IN connector
Note: The video connectors A and B on the monitor are Safety Extra Low
Voltage (SELV) circuits.
2. Route the cables through the cable clamp and the cable hook.
Cable hook
Cable clamp
6
AQU5611D BK/AQU5611DT BK 9.2 Million Pixels Color TFT LCD Monitor USER MANUAL
3. Reinstall the connector cover on the monitor.
2
Connector cover
1
1
4. Reinstall the stand rear cover and turn the monitor to the upright position.
Stand rear cover
Note: Do not power on the monitor or the computer until instructed. Failing to
do so may damage these units or the video graphics card.
Chapter 2. Hardware setup
7
Connecting the digital signal cable
1. Make sure that the video graphics card is installed on your computer.
2. Make sure that the power cord is NOT connected to your computer.
3. Open the cover of your computer, if necessary.
4. Connect the connector end marked ″1 PRIMARY″ to the DVI port marked ″1″,
and the connector end marked ″2 SECONDARY″ to the DVI port marked ″2″ of
the video graphics card.
5. If you have opened the cover of your computer, close it.
Notes:
a. If you want to use the extended function, then install the program to your
computer now if you have not installed it yet. Then connect the USB
connector to the USB port. If you don’t have this program, you can
download it from the following Web site: http://www.iiyama.co.jp
b. Do not connect the USB connector to the USB port if you don’t have the
extended function program installed on your computer. Connecting this
connector may damage your monitor, computer, or other attached USB
devices.
c. If your video graphics card has only one DVI port, then connect the
connector of the digital signal cable marked ″1 PRIMARY″ to the DVI port on
the video graphics card of your computer.
d. With the ATI® FireGL™4 video graphics card, use ATI device driver version
2078 (or higher) for the best performance of the monitor. The device driver
is available at the following Web site: http://support.ati.com
8
AQU5611D BK/AQU5611DT BK 9.2 Million Pixels Color TFT LCD Monitor USER MANUAL
Connecting the power cord
Note: Read the respective ″Danger Statements″ on pages iii before continuing with
this section.
1. Connect the power cord to the power adapter.
2. Connect the power plug to a properly grounded power outlet.
Note: Make sure that all the cables are connected, otherwise the power-on light
will not turn on.
3. Connect the computer to a properly grounded power outlet and turn on the
power switch.
Chapter 2. Hardware setup
9
4. Press the power switch on the monitor. The power light comes on.
Power switch
Power lighit
Notes:
a. When you turn off the monitor, wait at least five seconds before turning it on
again.
b. If you accidentally disconnected the power cord from the main outlet and
you connected it to the outlet again, the screen may flicker continuously. To
stop the flicker, press the power switch and turn off the monitor, then turn it
on again.
information on the power light.
This completes the hardware setup.
Supplementary Information
When powering on the different units, power them on in the following
sequence:
1. Monitor
2. Peripheral units
3. Computer
10 AQU5611D BK/AQU5611DT BK 9.2 Million Pixels Color TFT LCD Monitor USER MANUAL
Chapter 3. Adjusting and maintaining your monitor
This chapter describes the following:
v How to adjust the viewing angle.
v How to set the controls.
v The operating status of your monitor.
v How to disconnect the cables.
v How to use the security keylock.
v How to maintain your monitor.
Adjusting the viewing angle
You can adjust the vertical angle of the monitor to avoid unnecessary light reflection
and to make viewing easier. Tilt the screen angle vertically by grasping both sides
of the monitor and pulling it forward or backward.
11
Setting the monitor control buttons
You can control the various functions of the monitor using the buttons at the front
right of the monitor.
The four buttons control the following functions:
Button/
Button Name
Direct access functions
Functions available from the OSD
Menu
Displays the on-screen
display (OSD) menu.
Enters highlighted menu mode.
Menu/Enter
Left-Arrow
Right-Arrow
Sets the screen to a dimmer Moves the cursor to the left for
view.
highlighting the icons or for making
adjustments.
Sets the screen to a brighter Moves the cursor to the right for
view.
highlighting the icons or for making
adjustments.
Switches the monitor on or off.
On/Off
12 AQU5611D BK/AQU5611DT BK 9.2 Million Pixels Color TFT LCD Monitor USER MANUAL
Accessing the on-screen display (OSD) menus
You can access the on-screen display (OSD) menus by pressing the Menu/Enter
button. The OSD menus enable you to set the various operating conditions of your
monitor.
The OSD menus consist of the following:
v Main menu (for menu selection)
v Submenus (for controls setting)
– Brightness level
– Select video input type (single, dual, 4-vertical stripes, 4-tiles)
– Display key information (vertical frequency resolution)
Main menu
To access the Main menu, press the Menu/Enter button. The Main menu appears
on the display screen.
OSD Icon
Description
Used to display the Brightness submenu.
Used to display the Video Input submenu.
Used to display the Information submenu.
Exit from the Main menu.
To exit the Main menu, select the Exit icon using the Left-Arrow or the
Right-Arrow button, then press the Menu/Enter button.
To reset the OSD settings to the default value, do the following:
1. Power off the monitor.
2. While pressing the Menu/Enter button, press the Power switch to on. The
Power light changes cyclically between green and amber for several seconds.
Chapter 3. Adjusting and maintaining your monitor 13
Submenus
To access a submenu, do the following:
Brightness
submenu
1. Select the Brightness icon on the Main menu using the Left-Arrow or the
Right-Arrow button
2. Press the Menu/Enter button. The Brightness submenu appears.
3. Adjust the brightness using the Left-Arrow or the Right-Arrow button.
4. Press the Menu/Enter button to exit from this submenu.
Video input
submenu
1. Select the Video Input icon on the Main menu using the Left-Arrow or the
Right-Arrow button.
2. Press the Menu/Enter button. The Video Input submenu appears.
1 0
14 AQU5611D BK/AQU5611DT BK 9.2 Million Pixels Color TFT LCD Monitor USER MANUAL
OSD Icon
Description
One video input mode.
Two video input mode.
(The color management function is always effective.)
Four stripes video input mode.
(The color management function is always effective.)
Four tiles video input mode.
(The color management function is always effective.)
Exit from the Submenu.
1 or 0
(to the left of the
numbers)
Sets the color management function or the smooth character
display function.
You can use the color management function by choosing 1 when
the input mode
is being displayed. This is the default.
Note: You can use the color management function when any of
the input modes
,
, or
is being displayed regardless of
the numeric setting.
You can use the smooth character display function by choosing 0
when the input mode is being displayed.
1 or 0
(to the right of the
numbers)
Sets the present color management function setting.
You can use the color management function with the default
setting when you choose 0.
You can customize the color management function to your setting
when you choose 1.
Note: To find out more about the color management function, go
to the following Web site: http://www.iiyama.co.jp
3. When you want to change the color management function setting or the smooth
character display function setting when the input mode
is being displayed,
push the Left-Arrow button for several seconds.
4. Select the Exit icon to exit the submenu.
Information
submenu
1. Select the Information icon on the Main menu using the Left-Arrow or the
Right-Arrow button, to check the vertical frequency and the resolution of your
monitor.
2. Press the Menu/Enter button. The Information submenu appears.
1024
1280
3. Press the Menu/Enter button to exit from this submenu.
(example)
Chapter 3. Adjusting and maintaining your monitor 15
Knowing the operating status of your monitor
You can know the status of your monitor by the color of the power light.
Power light
The color of the power light changes from green to amber when your monitor
receives a time-out video signal from the computer and enters Standby mode to
save power. A time-out video signal is sent from your computer to the monitor when
the former detects inactivity on the keyboard or mouse for a set duration of time.
You can change the time-out duration for your monitor from the computer. Refer to
the manual shipped with your computer to change the time-out duration value.
Color
Green
Mode
Power
Consumption
Description
Normal
Operation (Maximum)
150 W
The monitor is operating normally and is receiving
the synchronous video signal from the computer.
Amber
Standby Less than 15
Either:
Mode
W
v
v
the monitor is in Standby mode to save power, or
the video cable is disconnected.
If the monitor is in Standby mode, it is not receiving
any video signals from the computer.
If the video cable is disconnected, refer to
Amber
(fast
blinking
at
0.25-sec.
intervals)
—
—
—
—
An error such as ″fan not working″ has occurred.
Amber
(slow
The monitor does not support the incoming video
signal.
blinking
at 1-sec.
intervals)
16 AQU5611D BK/AQU5611DT BK 9.2 Million Pixels Color TFT LCD Monitor USER MANUAL
Disconnecting the cable
CAUTION:
Do not use a digital signal cable other than the one shipped with the product.
Using some other cable may damage the monitor or the video graphics card.
The cable (P/N: 07N2227) is available at iiyama Customer Support Line (refer
to page 21).
To disconnect the digital signal cable, do the following:
1. Power off your monitor, peripheral units (if any), and computer and unplug them
from the power outlet.
5. Lift up the cables and take out the connector tool from the rear compartment of
the monitor (refer to page 5).
Note: Be sure to press the latch on the connector of the power adapter cord
when unplugging it from the DC-IN connector.
7. Insert the connector tool into the thumb screw on the digital signal cable
connector A ꢀ1ꢁ and turn it counterclockwise ꢀ2ꢁ to loosen the screw.
8. Disconnect the digital signal cable A from video connector A ꢀ3ꢁ.
2
Video connector
DC-IN connector
2
P/N: 07N2227
3
Connector tool
1
Note: The video connectors A and B on the monitor are Safety Extra Low
Voltage (SELV) circuits.
9. Store the connector tool back into the rear compartment of the monitor.
Chapter 3. Adjusting and maintaining your monitor 17
Using the security keylock
The monitor has a built-in security keyhole at the rear of the screen for fastening a
security lock and cable. This lock is used to help prevent the monitor from being
removed without your permission. This cable can be purchased at any PC shop.
First secure the cable to a stationary object; then attach the lock to the keyhole on
the rear of the monitor. For details of the installation, refer to the instructions
shipped with the security keylock.
Note: You are responsible for evaluating, selecting, and implementing the lock.
iiyama makes no comments, judgements, or warranties about the function,
quality, or performance of the lock.
Maintaining your monitor
Before cleaning or performing any maintenance operation on your monitor, be sure
to turn off the power on your monitor and computer.
v Gently wipe the monitor surface and the cover with a soft, clean cloth.
v Do not use flammable chemicals such as alcohol, thinner, or petroleum-based
solvents; they will cause a fire hazard and may also damage the screen coating.
18 AQU5611D BK/AQU5611DT BK 9.2 Million Pixels Color TFT LCD Monitor USER MANUAL
Chapter 4. Troubleshooting
Is something wrong?
If you suspect that something is not working correctly, you should:
1. Turn on the computer and monitor.
2. Set the brightness control (
) to the proper position.
3. Make sure that all cables are securely connected.
4. Disable the computer’s screen saver program, if it is enabled.
5. Set the display mode to the supported display mode.
6. If you still have a problem, go to the symptom list below and find the
symptom that most resembles yours.
Symptom list
Before calling your retailer or iiyama, find the symptom that most resembles yours,
and try the suggested action. You may be able to solve the problem yourself.
Symptom
Possible cause
Suggested action
The screen is blank
and the power indicator
is off
No power to the monitor
v
v
v
Make sure that the electrical outlet
and the monitor are both switched
on.
Make sure that the power cord is
firmly plugged into the electrical
outlet and the power supply unit.
If the power cord plug has a
removable fuse, replace it.
v
v
v
Try another power cord.
Try another electrical outlet.
The video graphics card is
defective. Replace it.
v
The computer is defective. Replace
it.
The screen is blank
and power indicator is
steady green
Brightness may be too
low
Adjust the brightness
The screen is blank
and the power indicator mode
is steady amber
The monitor is in Standby
v
v
Press any key on the keyboard or
move the mouse to restore
operation.
Check the Power Management
software on your computer.
The video cable is not
connected
v
v
v
v
Make sure that the signal cable is
firmly connected.
Make sure that no pins are bent in
the signal cable connector.
The video graphics card is
defective. Replace it.
The computer is defective. Replace
it.
19
The screen is blank
The display mode of the
v
v
v
Reconfigure the computer to use a
supported display mode.
and the power indicator computer is outside the
is blinking amber every range of the monitor
second
The video graphics card is
defective. Replace it.
The computer is defective. Replace
it.
The screen is blank
The monitor fan is not
v
v
Make sure that the power cord is
firmly plugged into the electrical
outlet.
and the power indicator working
is blinking amber every
0.25 second
Make sure that the power adapter
cord is firmly connected. If the
symptom remains, call your retailer
or iiyama.
v
v
The video graphics card is
defective. Replace it.
The computer is defective. Replace
it.
The image appears to
be smeared
There are noises in the
video signal
v
v
v
v
Make sure that the signal cable is
firmly connected.
Make sure that no pins are bent in
the signal cable connector.
The video graphics card is
defective. Replace it.
The computer is defective. Replace
it.
A few dots are missing, The LCD contains over 27,000,000 thin-film transistors (TFTs). A
discolored, or
inappropriately lighted
small number of dots may be missing, discolored, or lighted on
the screen. This is an intrinsic characteristic of the TFT LCD
technology and is not an LCD defect.
20 AQU5611D BK/AQU5611DT BK 9.2 Million Pixels Color TFT LCD Monitor USER MANUAL
Warranty information
Machine Name:
AQU5611D BK/AQU5611DT BK 9.2 Million Pixels Color TFT LCD
Monitor
Warranty Period: One (1) Year
Service and support
The terms and conditions of the services are described on the Warranty sheet. For
services, contact the Service Center listed on the Warranty sheet or contact your
dealer.
Before calling, please have available as much of the following information as
possible:
1. Type, model, and serial number from the label on the back of your monitor.
2. Purchase receipt
3. Description of problem
4. Computer type and model
5. System configuration (hardware attached, etc.)
6. System BIOS version number
7. Operating system and version number
8. Display driver version number
Chapter 4. Troubleshooting 21
22 AQU5611D BK/AQU5611DT BK 9.2 Million Pixels Color TFT LCD Monitor USER MANUAL
Appendix A. Specifications
The specifications of the monitor are as follows:
Dimensions
Width:
Height:
Depth:
Depth (without stand):
547 mm (21.5 in.)
439 mm (17.3 in.)
196 mm (7.7 in.)
105 mm (4.1 in.)
Weight
Unpackaged:
With base stand: 11.4 kg (25.1 lb.)
Power adapter: 1.3 kg (2.9 lb.)
Tilt
Angle:
Input:
−5° – +30°
Power
100 – 240 V AC, 50/60 Hz
Power consumption
Maximum:
Minimum:
150 W
Less than 15 W (In Standby Mode)
Video input
TMDSTM interface (RGB: 8 bits)
User controls
Power On/Off, Brightness
Regulatory compliance
v
v
v
v
v
v
v
v
v
v
v
CE Mark
CISPR22 A
EN 60950
FCC-A
IEC 60950
ISO 13406–2
TCO’95 (only available on AQU5611DT BK)
TÜV Ergonomics
TÜV GS
UL/CSA 60950
VCCI-A
Image Formation Time
Display area
62 ms (defined by ISO 13406–2)
Horizontal:
Vertical:
478.1 mm (18.8 in.)
298.8 mm (11.8 in.)
Temperature
Operating:
Storage:
Shipping:
0 – +35°C (32 – 95°F)
–20 – +60°C (–4 – 140°F)
–20 – +60°C (–4 – 140°F)
Relative humidity
Operating:
Storage:
Shipping:
8% – 80% (no condensation)
5% – 95% (no condensation)
5% – 95% (no condensation)
23
Supported display modes
The monitor supports the following display modes:
Horizontal
Frequency
(KHz)
Vertical
Frequency Frequency
Dot Clock
Actual Display
Resolution
Addressability
640 × 400
DVI Input
(Hz)
(MHz)
25.2
31.5
31.5
36.0
36.0
40.0
50.0
49.5
56.3
65.0
75.0
78.8
94.5
108.0
135.0
162.0
127.2
ch1
ch1
ch1
ch1
ch1
ch1
ch1
ch1
ch1
ch1
ch1
ch1
ch1
ch1
ch1
ch1
ch1
31.5 (N, P)
37.9 (N, P)
37.5 (N, P)
43.3 (N, P)
35.2 (P, N)
37.9 (P, N)
48.1 (P, N)
46.9 (P, N)
53.7 (P, N)
48.4 (N, P)
56.5 (N, P)
60.0 (P, N)
68.7 (P, N)
64.0 (P, N)
80.0 (P, N)
75.0 (P, N)
50.3 (N, P)
59.9 (N, P)
72.8 (N, P)
75.0 (N, P)
85.0 (N, P)
56.3 (P, N)
60.3 (P, N)
72.2 (P, N)
75.0 (P, N)
85.1 (P, N)
60.0 (N, P)
70.1 (N, P)
75.0 (P, N)
85.0 (P, N)
60.0 (P, N)
75.0 (P, N)
60.0 (P, N)
40.9 (P, N)
3200 × 2000
3200 × 2400
3200 × 2400
3200 × 2400
3200 × 2400
3200 × 2400
3200 × 2400
3200 × 2400
3200 × 2400
3072 × 2304
3072 × 2304
3072 × 2304
3072 × 2304
2560 × 2048
2560 × 2048
3200 × 2400
3200 × 2400
640 × 480
640 × 480
640 × 480
800 × 600
800 × 600
800 × 600
800 × 600
800 × 600
1024 × 768
1024 × 768
1024 × 768
1024 × 768
1280 × 1024
1280 × 1024
1600 × 1200
1920 × 1200
VGA
SVGA
XGA
SXGA
UXGA
UXGA-Wide
ch1, ch2,
ch3, ch4
(960 × 2400) × 4
99.2 (P, N)
49.6 (P, N)
40.9 (P, N)
40.9 (P, N)
104.8
104.8
3840 × 2400
ch1, ch2,
ch3, ch4
(1920 × 1200) × 4
3840 × 2400
(1920 × 2400) × 2
(1920 × 2400) × 2
(1920 × 2400) × 2
3840 × 2400
ch1, ch2
ch1, ch2
ch1, ch2
ch1
61.2 (P, N)
58.7 (P, N)
48.9 (P, N)
31.5 (P, N)
30.73 (N, P)
25.1 (P, N)
24.1 (P, N)
20.1 (P, N)
13.0 (P, N)
12.66 (P, N)
125.0
120.0
100.0
129.0
148.0
3840 × 2400
3840 × 2400
3840 × 2400
3840 × 2400
3840 × 2400
QUXGA-Wide
3840 × 2400
ch1
Notes:
1. N and P stand for the ″Negative″ and ″Positive,″ respectively. They indicate the
direction of polarity of the incoming signal to the monitor.
2. The type of resolutions supported depends on the video graphics card being
used.
24 AQU5611D BK/AQU5611DT BK 9.2 Million Pixels Color TFT LCD Monitor USER MANUAL
Updating the settings for your monitor
Unless you change the video graphics card that drives your monitor, there is usually
no need to change the settings. In case the need does arise, a procedure for
changing them is given in this appendix.
This operation must be done carefully. If incorrect parameters are specified, nothing
will be displayed.
Applicable models
The procedure given in this document applies to monitors with firmware at the
following levels:
DDC CPU
OSD CPU
USB CPU
Version 3.2 or higher
Version 5.0 or higher
Version 4.0 or higher
Version 34 or higher
FPGA LOGIC
Procedure
1. Setting
a. Connect the monitor to the personal computer that is to be used as a video
source.
b. Turn on the monitor and the PC. Wait until the system boots and a stable
screen image is displayed. Confirm that the power indicator on the monitor
shows green. If it is steady amber, press ″Debug switch″ with a stick to turn
on the monitor. (See the following figure).
CAUTION:
Do not use conductive material to press this switch. It may damage the
electric circuit inside of the monitor.
In this case, power indicator will show blinking amber, and image from PC
does not appear.
Some color pattern may appear on screen.
Appendix A. Specifications 25
2. Enabling the special OSD (on-screen display) menu
a. Press a menu switch and either the left switch or the right switch to select
the (i) (information) menu. On that menu, press the menu switch to enter the
information menu. There, a display showing the refresh rate and the screen
resolution appears, as in this example:
1200
1600
b. Press the left switch three times, and then press the right switch three times.
Page 1 of the special OSD menu appears, as in this example:
-1-
2
5.0
034
3.2
005
In this display, the firmware version is shown in the following format:
-1-
c
aaa bbb
ddd eee
where
aaa: DDC-CPU
bbb: OSD-CPU
c:
Reserved
ddd: USB-CPU
eee: FPGA-LOGIC
If the special OSD menu does not appear, press the menu switch to exit
3. Checking the current settings
a. Press the left or right switch to enter page 2 of the special OSD menu.
b. In about five seconds, the current settings will be displayed, as in this
example:
-2-
020
26 AQU5611D BK/AQU5611DT BK 9.2 Million Pixels Color TFT LCD Monitor USER MANUAL
If the setting is given as 000, any number greater than 63, or a value ending
4. Updating the settings
use.
b. Set the brightness parameter to the value for the settings you have chosen
OSD menu, you can set the brightness at any level from 0 to 63, as in this
example:
c. Enter page 1 of the special OSD menu.
d. Press the left or right switch to enter page 2 of the menu. Then press both
switches together, and hold them down until three dots appear on the
display. The three dots show that the settings are in the process of being
updated.
-2-
e. In five seconds, the setting number now stored in this monitor will be
displayed. If it is not the number you want, try again.
Note: An attempt to enter an unsupported setting number will fail.
If the number ends in x, the updating has failed because the settings have
not been programmed correctly. Try again.
f. Turn off the monitor to disable the special OSD menu.
Important notices
If the monitor is connected to a powered-down PC, or if the screen resolution
of the PC is being changed, the monitor will not be able to get access to the
settings.
The settings cannot be reset to the factory default values by the procedure
given in the user’s manual. To reset them to those values, check your model
name and choose appropriate number, then update the settings.
AQU5611D BK, AQU5611DT BK: Setting number 29
Appendix A. Specifications 27
Valid settings
DDC-CPU version 3.2 can detect and update some settings. If it encounters any it
does not recognize, it reads them as 000 (unknown).
From the following table, choose the settings that are appropriate for the operating
system and video graphics card you are using.
If you want to use settings not listed in the table, consider upgrading to another
version of DDC-CPU.
Settings are sometimes updated without notice. For the latest information, refer to
Even though a video graphics card is listed here, some of its functions may not be
supported.
Setting
number
Applicable model
Description
07
08
09
10
12
13
20
27
29
30
31
–
–
–
–
–
–
–
–
Reserved. Do not use.
Reserved. Do not use.
Reserved. Do not use.
Reserved. Do not use.
Reserved. Do not use.
Reserved. Do not use.
Reserved. Do not use.
Reserved. Do not use.
For ATl-FireGL (Windows®)
Reserved. Do not use.
Reserved. Do not use.
AQU5611D BK, AQU5611DT BK
–
–
28 AQU5611D BK/AQU5611DT BK 9.2 Million Pixels Color TFT LCD Monitor USER MANUAL
30 AQU5611D BK/AQU5611DT BK 9.2 Million Pixels Color TFT LCD Monitor USER MANUAL
Appendix C. Compliance
TCO’95
Congratulations!
You have just purchased a TCO’95 approved and labelled product! Your choice has
provided you with a product developed for professional use. Your purchase has also
contributed to reducing the burden on the environment and also to the further
development of environmentally adapted electronics products.
Why do we have environmentally labelled computers?
In many countries, environmental labelling has become an established method for
encouraging the adaptation of goods and services to the environment. The main
problem, as far as computers and other electronics equipment are concerned, is
that environmentally harmful substances are used both in the products and during
their manufacture. Since it is not so far possible to satisfactorily recycle the majority
of electronics equipment, most of these potentially damaging substances sooner or
later enter nature.
There are also other characteristics of a computer, such as energy consumption
levels, that are important from the viewpoints of both the work (internal) and natural
(external) environments. Since all methods of electricity generation have a negative
effect on the environment (e.g. acidic and climate-influencing emissions, radioactive
waste), it is vital to save energy. Electronics equipment in offices is often left
running continuously and thereby consumes a lot of energy.
What does labelling involve?
This product meets the requirements for the TCO’95 scheme which provides for
international and environmental labelling of personal computers. The labelling
scheme was developed as a joint effort by the TCO (The Swedish Confederation of
Professional Employees), Svenska Naturskyddsforeningen (The Swedish Society for
Nature Conservation) and Statens Energimyndighet (The Swedish National Energy
Administration).
Approval requirements cover a wide range of issues; environment, ergonomics,
usability, emission of electric and magnetic fields, energy consumption and electrical
and fire safety.
31
The environmental demands impose restrictions on the presence and use of heavy
metals, brominated and chlorinated flame retardants, CFCs (freons) and chlorinated
solvents, among other things. The product must be prepared for recycling and the
manufacturer is obliged to have an environmental policy which must be adhered to
in each country where the company implements its operational policy.
The energy requirements include a demand that the computer and/or display, after
a certain period of inactivity, shall reduce its power consumption to a lower level in
one or more stages. The length of time to reactivated the computer shall be
reasonable for the user.
Labelled products must meet strict environmental demands, for example, in respect
of the reduction of electric and magnetic fields, physical and visual ergonomics and
good usability.
Below you will find a brief summary of the environmental requirements met by this
product. The complete environmental criteria document may be ordered from:
TCO Development
SE-114 94 Stockholm, Sweden
Fax: +46 8 782 92 07
Email (Internet): [email protected]
Current information regarding TCO’95 approved and labelled products may also be
obtained via the Internet, using the address: http://www.tco-info.com/
Environmental Requirements
Brominated flame retardants
Brominated flame retardants are present in printed circuit boards, cables, wires,
casings and housings. In turn, they delay the spread of fire. Up to thirty percent of
the plastic in a computer casing can consist of flame retardant substances. These
are related to another group of environmental foxins, PCBs, which are suspected to
give rise to similar harm, including reproductive damage in fish eating birds and
mammals, due to the bio-accumulative1 processes. Flame retardants have been
found in human blood and researchers fear that disturbances in foetus development
may occur.
TCO’95 demand requires that plastic components weighing more than 25 grams
must not contain organically bound chlorine and bromine.
Lead
Lead can be found in picture tubes, display screens, solders and capacitors. Lead
damages the nervous system and in higher doses, causes lead poisoning.
TCO’95 requirement permits the inclusion of lead since no replacement has yet
been developed.1
Cadmium
Cadmium is present in rechargeable batteries and in the colour generating layers of
certain computer displays. Cadmium damages the nervous system and is toxic in
high doses.
TCO’95 requirement states that batteries may not contain more than 25 ppm
(parts per million) of cadmium. The colour-generating layers of display screens must
not contain any cadmium.1
1. Bio-accumulative is defined as substances which accumulate within living organisms.
32 AQU5611D BK/AQU5611DT BK 9.2 Million Pixels Color TFT LCD Monitor USER MANUAL
Mercury
Mercury is sometimes found in batteries, relays and switches. Mercury damages the
nervous system and is toxic in high doses.
TCO’95 requirements states that batteries may not contain more than 25 ppm
(parts per million) of mercury. It also demands that no mercury is present in any of
the electrical or electronics components concerned with the display unit.1
CFSc (freons)
CFCs (freons) are sometimes used for washing printed circuit boards and in the
manufacturing of expanded foam for packaging. CFCs break down ozone and
thereby damage the ozone layer in the stratosphere, causing increased reception
on Earth of ultraviolet light with consequent increased risks of skin cancer
(malignant melanoma).
The relevant TCO’95 requirement: Neither CFCs nor HCFCs may be used during
the manufacturing of the product or its packaging.
Federal Communications Commission (FCC) Statement
AQU5611D BK/AQU5611DT BK 9.2 Million Pixels Color TFT LCD Monitor
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to correct the interference at
his own expense.
Properly shielded and grounded cables and connectors must be used in order to
meet FCC emission limits. iiyama is not responsible for any radio or television
interference caused by using other than recommended cables and connectors or by
unauthorized changes or modifications to this equipment. Unauthorized changes or
modifications could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Industry Canada Class A Emission Compliance Statement
This Class A digital apparatus complies with Canadian ICES-003.
Avis de Conformité à la Réglementation d’Industrie Canada
Cet appareil numérique de classe A est conforme à la norme NMB-003 du Canada.
Deutsche EMV-Direktive (electromagnetische Verträglichkeit)
Dieses Gerät ist berechtigt in Übereinstimmung mit dem deutschen EMVG vom
9.Nov.92 das EG-Konformitätszeichen zu führen.
Der Aussteller der Konformitätserklärung ist die iiyama.
Appendix C. Compliance 33
Dieses Gerät erfüllt die Bedingungen der EN 55022 Klasse A. Für diese Klasse von
Geräten gilt folgende Bestimmung nach dem EMVG:
Geräte dürfen an Orten, für die sie nicht ausreichend entstört sind, nur mit
besonderer Genehmigung des Bundesminesters für Post und Telekommunikation
oder des Bundesamtes fur Post und Telekommunikation betrieben werden. Die
Genehmigung wird erteilt, wenn keine elektromagnetischen Störungen zu erwarten
sind.
(Auszug aus dem EMVG vom 9.Nov.92, Para.3. Abs.4)
Hinweis: Dieses Genehmigungsverfahren ist von der Deutschen Bundespost noch nicht
veröffentlicht worden.
European Union – EMC Directive
This product is in conformity with the protection requirements of the EU Council
Directive 89/366/ECC on the approximation of the laws of the Member States
relating to electromagnetic compatibility.
iiyama cannot accept responsibility for any failure to satisfy the protection
requirements resulting from a non-recommended modification of the product,
including the fitting of non-iiyama option cards.
This product has been tested and found to comply with the limits for Class A
Information Technology Equipment according to CISPR 22/European Standard EN
55022. The limits for Class A equipment were derived for commercial and industrial
environments to provide reasonable protection against interference with licensed
communication equipment.
Warning: This is a Class A product. In a domestic environment this product may cause
radio interference, in which case the user may be required to take adequate measures.
Union Européenne – Directive Conformité électromagnétique
Ce produit est conforme aux exigences de protection de la Directive 89/336/EEC du
Conseil de l’UE sur le rapprochement des lois des États membres en matière de
compatibilité électromagnétique.
iiyama ne peut accepter aucune responsabilité pour le manquement aux exigences
de protection résultant d’une modification non recommandée du produit, y compris
l’installation de cartes autres que les cartes iiyama.
Ce produit a été testé et il satisfait les conditions de l’équipement informatique de
Classe A en vertu de CISPR22/Standard européen EN 55022. Les conditions pour
l’équipement de Classe A ont été définies en fonction d’un contexte d’utilisation
commercial et industriel afin de fournir une protection raisonnable contre
l’interférence d’appareils de communication autorisés.
Avertissement: Ceci est un produit de Classe A. Dans un contexte résidentiel ce produit
peut causer une interférence radio exigeant que l’utilisateur prenne des mesures
adéquates.
34 AQU5611D BK/AQU5611DT BK 9.2 Million Pixels Color TFT LCD Monitor USER MANUAL
Union Europea – Normativa EMC
Questo prodotto è conforme alle normative di protezione ai sensi della Direttiva del
Consiglio dell’Unione Europea 89/336/CEE ull’armonizzazione legislativa degli stati
membri in materia di compatibilità elettromagnetica.
iiyama non accetta responsabilità alcuna per la mancata conformità alle normative
di protezione dovuta a modifiche non consigliate al prodotto, compresa
l’installazione di schede e componenti di marca diversa da iiyama.
Le prove effettuate sul presente prodotto hanno accertato che esso rientra nei limiti
stabiliti per le le apparecchiature di informatica Classe A ai sensi del CISPR
22/Norma Europea EN 55022. I limiti delle apparecchiature della Classe A sono
stati stabiliti al fine di fornire ragionevole protezione da interferenze mediante
dispositivi di comunicazione in concessione in ambienti commerciali ed industriali.
Avvertimento: Questo è un prodotto appartenente alla Classe A. In ambiente domestico,
tale prodotto può essere causa di interferenze radio, nel qual caso l’utente deve prendere
misure adeguate.
Europese Unie -- EMC-richtlijnen
Dit product voldoet aan de vereisten van de EU Raad richtlijnen 89/366/ECC
betreffende de approximatie van de wetten van de lidstaten die betrekking hebben
op elektromagnetische compatibiliteit.
iiyama kan niet aansprakelijk worden gesteld voor eventuele gebreken in de
conformiteit aan de vereisten als gevolg van ongeoorloofde modificaties in het
product, inclusief het aanbrengen van optionele kaarten van andere fabrikanten dan
iiyama.
Deze apparatuur is getest en bleek te voldoen aan de eisen en limieten voor Klasse
A IT-apparatuur overeenkomstig CISPR 22/Europese normering EN 55022, die
opgesteld zijn om in een commerciële en industriële omgeving een redelijke
bescherming tegen interferentie te bieden bij gebruik van geautoriseerde
communicatie-apparatuur.
Waarschuwing: Dit is een Klasse A product. Bij gebruik in woongebieden kan dit product
storing in radio- en televisie-ontvangst veroorzaken en is de gebruiker verplicht om de
storing op eigen kosten op te heffen.
Europeiska Unionen - EMC Direktiv
Denna produkt överensstämmer med skyddskraven i EU Rådets Direktiv 89/366/
ECC om harmonisering av medlemsstaternas lagregler för elektromagnetisk
kompatibilitet.
iiyama tar inte ansvar för försummelser att uppfylla skyddskraven som resultat av
en icke-rekommenderad modifiering av produkten, inklusive valfria kort som inte
tillverkats av iiyama.
Denna produkt har testats och funnits överensstämma med gränsmåtten för Class A
Information Technology Equipment i enlighet med CISPR 22/ European Standard
EN 55022. Gränsmåtten för Class A utrustning bestämdes för kommersiella och
industriella miljöer för ge rimligt skydd mot störningar med licenserad
Appendix C. Compliance 35
kommunikationsutrustning.
Varning: Detta är en Class A produkt. I hemmiljö kan produkten orsaka radiostörningar,
som kräver att användaren vidtager nödvändiga åtgärder.
Statements for Other Countries
Power Cord
For your safety, iiyama provides a power cord with a grounded attachment plug to
use with this iiyama product. To avoid electrical shock, always use the power cord
and plug with a properly grounded power outlet.
Power cords used in the United States and Canada are listed by the Underwriter’s
Laboratories (UL) and/or certified by the Canadian Standards Association (CSA).
For units intended to be operated at 115 volts: Use a UL-listed and/or CSA-certified
cord set consisting of a minimum 18 AWG, Type SVT or SJT three-conductor cord,
a maximum of 15 feet long, and a parallel blade, grounding-type attachment plug
rated 15 amperes, 125 volts.
For units intended to be operated at 230 volts (U.S. use): Use a UL-listed and/or
CSA-certified cord set consisting of a minimum 18 AWG, type SVT or SJT
three-conductor cord, a maximum of 15 feet long, and a tandem blade,
grounding-type attachment plug rated 15 amperes, 250 volts.
For units intended to be operated at 230 volts (outside the U.S.): Use a cord set
with a grounding-type attachment plug. The cord set should have the appropriate
safety approvals for the country in which the equipment will be installed.
Power cords for a specific country or region are usually available only in that
country or region.
Power cord part number
13F9959
Used in these countries or regions
United States of America
13F9996
Denmark
14F0032
United Kingdom, China (Hong Kong S.A.R.)
39H0212 or 6454377
14F0050
Japan
Switzerland
Italy
14F0068
MPRII
This product complies with Swedish National Council for Metrology (MPR)
standards issued in December 1999 (MPRII) for very low frequency (VLF) and
extremely low frequency (ELF) emissions.
36 AQU5611D BK/AQU5611DT BK 9.2 Million Pixels Color TFT LCD Monitor USER MANUAL
Hinweise
Gemäβ der Amtsblätter des BMPT Nm. 61/1991 und 6/1992 wird der Betreiber
darauf aufmerksam gemächt, daβ die von ihm mit diesem Gerät zusammengestellte
Anlage auch den technischen Bestimmungen dieser Amtsblätter genügen muβ.
Aus ergonomischen Gründen wird empfohlen, die Grundfarbe Blau nicht auf
dunklem Untergrund zu verwenden (schlechte Erkennbarkeit, Augenbelastung bei
zu geringem Zeichenkontrast).
Aus ergonomischen Gründen sollten nur Darstellungen auf dunklem Hintergrund bei
Vertikalfrequenzen ab 60 Hz (ohne Zeilensprung) benutzt werden.
Die Konvergenz des Bildes kann sich auf Grund des Magnetfeldes am Ort der
Aufstellung aus der Korrekten Grundeinstellung verändern. Zur Korrektur empfiehlt
es sich deshalb, die Regler an der Frontseite für H STAT und V STAT so
einzustellen, daβ die getrennt sichtbaren Farblinien für Rot. Grün und Blau bei z.B.
der Darstellung eines Buchstabens zur Deckung (Konvergenz) gelangen. Siehe
hierzu auch die Erklärungen zu H STAT und V STAT.
Appendix C. Compliance 37
38 AQU5611D BK/AQU5611DT BK 9.2 Million Pixels Color TFT LCD Monitor USER MANUAL
|