I N S T A L L A T I O N / O P E R A T I O N
PMC14H and PMC14H-GY
14-Inch Color Monitor
®
C2906M (7/03)
DESCRIPTION
The PMC14H is a high-resolution color monitor that can be used in desktop applications or rack mounted using the optional
RMA14F rack mount kit. The monitor supports NTSC and PAL video, as well as 120 VAC and 230 VAC input power. An
automatic switching system makes all the necessary changes for adapting to the required formats. Manual selection is not
required. A separate power cord is supplied for each voltage input.
The back panel of the PMC14H has two BNC video inputs with looping outputs, one S-Video input, and multiple audio inputs
and outputs. All image adjustment controls are conveniently located on the front panel of the monitor.
C2906M (7/03)
3
INSTALLATION
Table A. Video Coaxial Cable Requirements
1. Make all equipment connections as required for your
installation. Refer to Figures 1 through 3 for samples of
installation methods.
Cable Type*
RG59/U
Maximum Distance
750 ft (229 m)
Refer to Table A for coaxial cable requirements.
RG6/U
1,000 ft (305 m)
1,500 ft (457 m)
2. Plug power cord into the AC INLET connection on the
rear panel of the monitor. Plug the other end into a
power receptacle.
RG11/U
*Minimum cable requirements:
75 ohms impedance
All-copper center conductor
All-copper braided shield with 95% braid coverage
CAMERA
VIDEO
AUDIO
V1
V2
V1
V2 S-VIDEO
IN
IN
CAMERA
OUT
OUT
S-VIDEO
VCR
VCR
Figure 1. Looping Operation – One Monitor with External Video Equipment
4
C2906M (7/03)
VIDEO
AUDIO
V2 S-VIDEO
V1
V2
V1
IN
IN
OUT
CAMERA
OUT
S-VIDEO
S-VHS OUT
AUDIO OUT
VCR
Figure 2. S-VHS Video Input Connections
Note: The S-Video connector is an input connector; there is no loop-through capability using S-Video.
VIDEO
AUDIO
V2 S-VIDEO
V1
V1
V1
V2
V2
V2
V1
V1
V1
IN
IN
CAMERA
OUT
OUT
S-VIDEO
S-VIDEO
S-VIDEO
VIDEO
AUDIO
V2 S-VIDEO
IN
IN
OUT
OUT
VIDEO
AUDIO
V2 S-VIDEO
IN
IN
OUT
OUT
VCR
Figure 3. Looping Operation – Maximum of Three Monitors with External Video Equipment
C2906M (7/03)
5
OPERATION
1. Press the POWER button to turn the monitor on. The LED above the power button will illuminate when the monitor is on.
2. Select the camera by pressing the V1, V2, or S-VIDEO button (refer to Figure 4).
3. If required adjust the picture using the control knobs on the front panel. Refer to Figure 4 for front panel controls.
FRONT PANEL ADJUSTMENTS
TINT
Color phase adjustment. Turn clockwise to increase the greenish tones in the picture. Turn counterclockwise
to increase the reddish tones in the picture.
COLOR Color saturation level. Turn the control knob clockwise to increase the saturation level and counterclockwise
to decrease the saturation level.
CONT
Contrast adjustment. Proper adjustment will allow maximum gradations between the darkest and lightest
picture contrast. Turn the control clockwise to increase picture contrast and counterclockwise to decrease
contrast.
BRIGHT Brightness display adjustment. Turn the control clockwise to increase brightness and counterclockwise to
decrease brightness.
SHARP Sharpness adjustment. Adjust control knob to obtain the clearest picture.
VOLUME Audio adjustment. Turn the control clockwise to increase volume and counterclockwise to decrease volume.
PMC14H
V1
V2 S-VIDEO
TINT
SHARP
COLOR
BRIGHT
CONT.
VOLUME
POWER
Figure 4. Front Panel of Monitor
6
C2906M (7/03)
SPECIFICATIONS
ELECTRICAL
Input Voltage:
100-240 VAC, 50/60 Hz, automatic switching
45 watts
450 TV lines, center of screen
14-inch (35.56 cm) diagonal
10%
Power Consumption:
Horizontal Resolution:
Visual Picture Size:
Sweep Linearity:
Speaker Output:
1.0 watt (-3 dBV)
GENERAL
Input/Output
Video:
2 BNC inputs, 75 ohms or Hi-Z
2 looping outputs
3 RCA inputs, Hi-Z
3 looping outputs
1 DIN input
Audio:
S-Video:
Construction:
Finish
Steel cabinet
PMC14H:
PMC14H-GY
Dimensions:
Black
Gray
13.76 (W) x 12.89 (H) x 14.59 (D) inches
(34.8 x 32.7 x 37.0 cm)
30.6 lb (14 kg)
Weight:
ENVIRONMENTAL
Operating Temperature: 32° to 106°F (0° to 41°C)
Humidity: 10% to 85% (non-condensing)
(Design and product specifications subject to change without notice.)
REVISION HISTORY
Manual #
Date
Comments
C2906M
7/03
Original version.
® Pelco and the Pelco logo are registered trademarks of Pelco.
C2906M (7/03)
© Copyright 2003, Pelco. All rights reserved.
7
WARRANTY AND RETURN INFORMATION
WARRANTY
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to
obtain a Repair Authorization number (RA), and provide the following information:
Pelco will repair or replace, without charge, any merchandise proved defective in material or
workmanship for a period of one year after the date of shipment. Exceptions to this warranty are
as noted below:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
•
•
Five years on Pelco manufactured cameras (CC3500/CC3600/CC3700 and MC3500/
MC3600 Series); two years on all other cameras.
Three years on Genex® Series (multiplexers, server, and keyboard) and 090 Series
Camclosure® Camera System.
If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions
stated above, please include a written explanation with the product when returned.
•
•
•
Two years on 100/150, 200 and 300 Series Camclosure® Camera Systems.
Two years on all standard motorized or fixed focal length lenses.
Two years on Legacy®, CM6700/CM6800/CM8500/CM9500/CM9740/CM9760 Matrix, DF5
and DF8 Series Fixed Dome products.
Method of return shipment shall be the same or equal to the method by which the item was received by
Pelco.
•
Two years on Spectra®, Esprit®, and PS20 Scanners, including when used in continuous
motion applications.
RETURNS
In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100
or (559) 292-1981 to obtain an authorization number (CA number if returned for credit, and RA number if
returned for repair).
•
•
•
Two years on Esprit and WW5700 series window wiper (excluding wiper blades).
Eighteen months on DX Series digital video recorders.
One year (except video heads) on video cassette recorders (VCRs). Video heads will be
covered for a period of six months.
Six months on all pan and tilts, scanners or preset lenses used in continuous motion
applications (that is, preset scan, tour and auto scan modes).
All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.
•
Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and
freight should be prepaid. Ship to the appropriate address below.
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident
are not covered under this warranty.
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico:
Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the
specific use or application made of the Products. Pelco’s liability for any claim, whether based on
breach of contract, negligence, infringement of any rights of any party or product liability, relating
to the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no
event will Pelco be liable for any special, incidental or consequential damages (including loss of
use, loss of profit and claims of third parties) however caused, whether by the negligence of
Pelco or otherwise.
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico:
Intermediate Consignee
American Overseas Air Freight
320 Beach Road
Burlingame, CA 94010
USA
Ultimate Consignee
Pelco
3500 Pelco Way
Clovis, CA 93612-5699
USA
The above warranty provides the Dealer with specific legal rights. The Dealer may also have
additional rights, which are subject to variation from state to state.
This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/
96/EC of the European Union regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your
local dealer for procedures for recycling this equipment.
World Headquarters
3500 Pelco Way
Clovis, California 93612 USA
USA & Canada
Tel: 800/289-9100
Fax: 800/289-9150
International
Tel: 1-559/292-1981
Fax: 1-559/348-1120
ISO9001
Orangeburg, New York Las Vegas, Nevada Eindhoven, The Netherlands Wokingham, United Kingdom Montreal, Canada
|