In-dash 7"Widescreen Color LCD Monitor/DVD Receiver
인대쉬 7" 와이드스크린 컬러 LCD 모니터/DVD 리시버
7-‰˛ÈÏÓ‚˚È ‡‚ÚÓÏÓ·ËθÌ˚È ¯ËÓÍӽ͇ÌÌ˚È ˆ‚ÂÚÌÓÈ Üä-ÏÓÌËÚÓ/DVD-ÂÒË‚Â
TILT
CLOSE
Model:
CQ-VD7005W
PWR
MUTE
SRC
VOL
ENTER
/
BAND
ENT
CQ-VD7005W
TOP MENU
TEXT
RET
RETURN
DVD MENU
VOL
CAR AV
ENTER
PWR
MUTE
SRC
MENU
NAVI
TEXT
❑
Use the designated parts and tools for installation.
Use the supplied or designated parts and appropriate tools
to install the product. The use of parts other than those
supplied or designated may result in internal damage to the
unit. Faulty installation may lead to an accident, a malfunc-
tion or fire.
Do not block the air vent or the cooling plate of the
unit.
Blocking these parts will cause the interior of the unit to
overheat and will result in fire or other damage.
Do not install the product where it is exposed to
strong vibrations or is unstable.
Avoid slanted or strongly curved surfaces for installation. If
the installation is not stable, the unit may fall down while
driving and this can lead to an accident or injury.
Caution
Observe the following cautions when using
this unit.
Keep the sound volume at an appropriate level.
Keep the volume level low enough to be aware of road and
traffic conditions while driving.
Do not insert or allow your hand or fingers to be
caught in the unit.
To prevent injury, do not get your hand or fingers caught in
moving parts or in the disc slot. Especially watch out for
infants.
This unit is designed for use exclusively in auto-
mobiles.
Do not operate the unit for a prolonged period with
the engine turned off.
Operating the audio system for a long period of time with
the engine turned off will drain the battery.
2
❑
❑
❑
❑
❑
❑
❑
Installation Angle
The product should be installed in a horizontal position
with the front end up at a convenient angle, but not more
than 30˚.
The user should bear in mind that in some areas there may
be restrictions on how and where this unit must be
installed. Consult your dealer for further details.
Wear gloves for safety. Make sure that wiring is
completed before installation.
To prevent damage to the unit, do not connect the
power connector until the whole wiring is complet-
ed.
Do not connect more than one speaker to one set
of speaker leads. (except for connecting to a
tweeter)
❑
❑
Do not expose the unit to direct sunlight or exces-
sive heat.
Otherwise these will raise the interior temperature of the
unit, and it may lead to smoke, fire, or other damage to the
unit.
❑
❑
Do not use the product where it will be exposed to
water, moisture, or dust.
Exposure of the unit to water, moisture, or dust may lead
to smoke, fire, or other damage to the unit. Make especially
sure that the unit does not get wet in car washes or on
rainy days.
❑
Observe the following cautions when
installing.
Observe the following cautions when handling
the battery for the remote control unit.
❑
Refer wiring and installation to qualified service
personnel.
●
●
Use only specified battery (CR2025).
Match the polarity of the battery with the (+) and (–) marks
in the battery case.
Replace a dead battery as soon as possible.
Remove the battery from the remote control unit when not
using it for an extended period of time.
Insulate the battery (by placing them in a plastic bag or
covering them with vinyl tape) before disposal or storage.
Dispose of the battery according to the local regulations.
Do not disassemble, recharge, heat or short the battery. Do
not throw a battery into a fire or water.
Installation of this unit requires special skills and experi-
ence. For maximum safety, have it installed by your dealer.
Panasonic is not liable for any problems resulting from
your own installation of the unit.
●
●
●
❑
❑
Follow the instructions to install and wire the prod-
uct.
●
●
Not following the instructions to properly install and wire
the product could cause an accident or fire.
Take care not to damage the leads.
In case of battery leakage
When wiring, take care not to damage the leads. Prevent
them from getting caught in the vehicle chassis, screws,
and moving parts such as seat rails. Do not scratch, pull,
bend or twist the leads. Do not run them near heat sources
or place heavy objects on them. If leads must be run over
sharp metal edges, protect the leads by winding them with
vinyl tape or similar protection.
●
●
●
Thoroughly wipe the battery liquid off the battery case and
insert new battery.
If any part of your body or clothing comes into contact
with battery liquid, wash it with plenty of water.
If battery liquid comes into contact with your eyes, wash
them with plenty of water and get immediate medical atten-
tion.
CAUTION:
• PLEASE FOLLOW THE LAWS AND REGULATIONS OF YOUR STATE, PROVINCE OR COUNTRY FOR WIRING,
INSTALLATION, AND USE OF THIS UNIT AND THE DEVICES TO BE CONNECTED.
3
CQ-VD7005W
Safety Information (continued)
Caution
THIS PRODUCT IS A CLASS I LASER PRODUCT.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE
OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN
MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR BY YOUR-
SELF. REFER SERVICING TO QUALIFIED PERSONNEL.
3
This system is designed so that you
cannot see moving pictures while
you are driving.
Park your car in a safe place and pull the side
brake (parking brake) lever before watching the
monitor.
¡
A rear monitor (option) displays moving pic-
¡
tures while driving.
Note:
¡Be sure to connect the side brake (parking
brake) connection lead. (aInstallation
Instructions)
4
CQ-VD7005W
Notes on Use
Liquid Crystal Panel
¡Do not cause impact to the liquid crystal panel.
¡Usage temperature range: 0 °C to 40 °C
When the temperature is very cold or very hot, the
image may not appear clearly or may move slowly.
Also, movement of the image may seem to be out of
synchronization or the image quality may decline in
such environments. Note that this is not a malfunction
or problem.
¡Sudden changes in the temperature inside the car such
as those which occur immediately after the car’s air
conditioner or heater has been turned on may cause
the inside of the liquid crystal panel to cloud over due
to water vapor or it may cause condensation (droplets
of water) to form and, as a result, the panel may not
work properly. Do not use the unit while these symp-
toms are in evidence but leave the unit standing for
about and hour, and then resume or start use.
4
¡In order to protect the liquid crystal panel, keep it out
of direct sunlight while the unit is not in use.
Before Reading These Instructions
Differences among 4 Models
This operating instruction manual is for 4 models CQ-VD7005W2/CQ-VD7005W3/
CQ-VD7005W4 and CQ-VD7005W5.
The following table shows the playable region number for each model.
Example:
2
5
3
4
Model
Playable region number
2 (ALL)
CQ-VD7005W2
CQ-VD7005W3
CQ-VD7005W4
CQ-VD7005W5
ALL
3 (ALL)
4 (ALL)
“Before Disc Playback”
(apage 16)
5 (ALL)
Components
TILT
OPEN
/
CLOSE
XXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXX
XXXXXXXXXXXXXXXX
OO-OOOOO
1. Main Unit
5. System Upgrade Guidebook
<YFM284C676ZA>
(LCD monitor/DVD player)
/
CQ-VD7005W
0U
TT
O
TEXT
VOL
Qty.: 1
Qty.: 1
DISC
Qty.: 1
ENTER
TUNE
/
PWR
SRC
TRACK
MUTE
MENU
NAVI
PWR
SRC
XXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXX
MUTE
2. Remote Control Unit
<EUR7641060>
XXXXXXXXXXXXXXXX
OO-OOOOO
VOL
6. Installation Instructions
<YFM294C099ZA>
ENTER
/
BAND
ENT
TOP MENU
RET
RETURN
DVD MENU
(includes a battery: CR2025)
CAR AV
Qty.: 1
Qty.: 1
3. Wiping Cloth
<YEFX9991793>
7. Installation Hardware (screws,
cords, etc.)
(aInstallation Instructions)
XXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXX
XXXXXXXXXXXXXXXX
Note:
OO-OOOOO
4. Operating Instructions
<YFM284C675ZA>
¡The number in parenthesis underneath each accessory
part name is the part number for maintenance and
service.
Qty.: 1
¡Accessories and their parts numbers are subject to
modification without prior notice due to improvements.
5
CQ-VD7005W
Features
Panasonic welcomes you to our constantly growing family of electronic products owners.
We endeavor to give you the advantages of precise electronic and mechanical engineering, manufactured with carefully
selected components, and assembled by people who are proud of the reputation their work has built for our company.
We know this product will bring you many hours of enjoyment, and after you discover the quality, value and reliability
we have built into it, you too will be proud to be a member of our family.
5
Please refer to the separate “System Upgrade Guidebook” for how to operate this unit when optional devices are
connected.
■ No device is connected to this unit. aBasic operations are covered only by this book.
■ Optional devices are connected to this unit. aRefer to the “System Upgrade Guidebook” in addition.
■ Simultaneous Multi-Device Connection
(with Expansion Module (hub unit))
You can connect the optional Expansion Module (hub
unit) (CY-EM100N). Connection of the Expansion
Module allows you to simultaneously connect
optional devices mentioned before as well as other
AV devices. For details, refer to the operating instruc-
tions for the Expansion Module.
■ CS Auto (Circle Surround Automotive)
CS Auto allows your car interior to change to a
splendid audio room in a moment. Every speaker can
be fine-tuned. ( page 33)
a
is a trademark of SRS Labs, Inc.
CS Auto technology is incorporated under license
from SRS Labs, Inc.
Connectable devices
¡CD/DVD changer (max. 1)
¡iPod (max. 2)
¡iPod with Video (max. 1)
¡Hands-Free Phone System (max. 1)
¡TV tuner (max. 1)
Note:
®
If you enable CS Auto, the following functions are
automatically disabled:
¡
GRAPHIC-EQ
,
CROSS OVER
,
DOWN MIX
,
MULTI-CH
(
a
page 32-37).
Note:
■ Touch Panel Operation
¡Market conditions regarding optional devices vary
with countries and regions. For further information,
consult your dealer.
¡If a non-Panasonic product is connected to this unit,
we do not guarantee the operations of the product.
¡If iPod with Video is connected, no more iPod can
be connected.
Simply touch the screen lightly to operate virtually all
functions. Easy-to-use menus and icons let you
“touch and choose” what you want, so you can start
using your system from the very first day. That also
means that while you drive, you can concentrate on
the road.
■ DVD–R, DVD–RW Playback
■ Integration of the monitor, FM/AM radio,
DVD Video/Video CD player and
CD/MP3/WMA player
■ Built-in AV Input/Output Terminals
For more convenient connection and setup, all termi-
nals are now provided on the unit itself.
(
a
page 16, 48 for details)
■ ID code
4-digit ID code for increased security.
Fill in the ID code memo (apage 46).
■ Built-in Dolby Digital decoder, DTS decoder
You can enjoy a powerful 5.1 channel surround sys-
tem by connecting optional center speaker, power
amplifier and sub-woofer.
■ Built-in DSP
7 bands graphic equalizer. ( page 32)
a
■ GUI (Graphic User Interface)
GUI displays various indications with colorful sym-
bols to enhance visibility, enjoyment, and operability.
■ Disc type and input signal auto-detection
The signal auto-detection function of this unit allows
users to be free from selection between PAL and
NTSC before use of your discs or devices. (For out-
put signal, set TV TYPE . ( page 36))
a
6
CQ-VD7005W
Contents
English
2
한국어
52
102
êÛÒÒÍËÈ
¢Safety Information.......................... 2
¢Notes on Use................................................... 5
¢Before Reading These Instructions .............. 5
¢Components.................................................... 5
¢Features........................................................... 6
¢Preparation...................................... 8
First time power on, other settings, remote control
unit, symbols used in this manual
¢Name of Controls and Functions ................ 10
¢Touch Panel Operation Oveview................. 12
¢General .......................................... 14
Power on/power off, display open/close, source
selection, volume, mute, tilt angle, folding down the
display temporarily
¢
¢
Before Disc Playback..................... 16
Disc Player..................................... 18
¢Notes on MP3/WMA ...................................... 22
¢Radio.............................................. 24
¢AV1/AV2 ......................................... 26
¢Settings ......................................... 28
Menu operation
User, screen, audio, DVD, input/output, radio
¢Troubleshooting ........................... 41
¢Maintenance .................................................. 47
¢Notes on Discs.............................................. 48
¢Language Code List...................................... 49
¢Definition of Terms ....................................... 50
¢Specifications................................................ 51
7
CQ-VD7005W
Preparation
First Time Power On
Remote Control Unit
The speaker setup screen appears after the opening dis-
play when the power is turned on for the first time.
Perform speaker setup according to the car conditions in
Before Initial Use
Pull the insulation film out from
the backside of the remote con-
trol gently.
7
SP SETUP
which this unit is installed. (
apage 34)
Other Settings
Battery Replacement
Please refer to the separate “System Upgrade
Guidebook” for how to operate this unit when option-
al devices are connected.
q Remove the battery holder with the remote control
unit placed on a flat surface.
q Stick your thumbnail into the groove and push the
holder in the direction of the arrow at the same
time.
w Pull it out in the direction of the arrow using a
tough pointed object.
(user settings) ( page 30)
a
USER
display unit, clock, ID code, memory clear, other
(screen settings) ( page 32)
a
SCREEN
dimmer, picture
(audio settings) ( page 32)
a
AUDIO
Tough pointed object
sound setup, graphic equalizer, CS Auto, speaker set up,
speaker level, time alignment, source level, cross over
(DVD settings) ( page 36)
a
DVD
language, display, pro logic, down mix, dynamic range
compression, multiple channel
(AV-IN/OUT settings) ( page 37)
a
INPUT/OUTPUT
source skip
w Put a battery in the case with (+)-side facing up.
e Put the case back.
(radio settings) ( page 38)
a
RADIO
FM set up, AM set up
Lithium battery (CR2025)
Battery case
2
Note:
Refer to “Settings” ( page 28) for further information
¡
a
about operations, settings, and others of the menu
screen.
3
Warning
You may need to set the following depending on the
devices to be connected.
¡Keep batteries away from children to avoid the risk
of accidents. If an infant ingests a battery, please
seek immediate medical attention.
Subwoofer
¡
Execute SP LEVEL (speaker level). ( page 34)
a
Caution
¡Remove and dispose of an old battery immediately.
¡Do not disassemble, heat or short a battery. Do not
throw a battery into a fire or water.
AV1/AV2 (Camcorder, VCR, etc.)
Adjust SOURCE LEVEL (AV1/AV2 input level).
¡
¡Follow local regulations when disposing of a battery.
¡Improper use of a battery may cause overheating, an
explosion or ignition, resulting in injury or a fire.
(
a
page 35)
Warning
Note:
¡Battery Information:
Battery Type: Panasonic lithium battery (CR2025)
Battery Life: Approximately 6 months under normal
use (at room temperature)
¡When you connect external devices to AV1-IN/
AV2-IN (AV1/AV2), be sure to connect the side
brake connection lead (aInstallation Instructions).
8
CQ-VD7005W
Symbols used in this manual
Pictographs
Disc Marks
8
The following pictographs are used for the descriptions
You can perform some operations of this unit in one or
more methods with the touch panel or remote control.
This book explains such operations in tabular form as fol-
lows. Refer to the following for the pictographs located in
the upper part of each table.
of disc operation. (apage 17-21)
DVD
: DVD
VCD
: VCD (Video CD)
CD : CD
Compatible
Discs
MP3 : CD-R/RWs containing MP3 files
WMA : CD-R/RWs containing WMA files
Compatible types of disc
The discs compatible with the targeted operation.
Operation on the Touch Panel
You can use the touch panel to perform the targeted
operation. If the operation is not executable with the
touch panel, “––” is displayed.
Operation on the Remote Control Unit
You can use the remote control to perform the targeted
operation. If the operation is not executable with the
remote control, “––” is displayed.
Operation on the Main Unit
You can use the Main Unit to perform the targeted opera-
tion. If the operation is not executable with the Main Unit,
“––” is displayed.
9
CQ-VD7005W
Name of Controls and Functions
![TILT]
Main Unit
o[OPEN] (CLOSE)
(Display Raised)
TILT
CLOSE
9
q[ASP] (ASPECT)
(P•MODE (PRIVATE
MODE))
Display
Disc slot
Remote control
sensor
w[VOL]
i
CQ-VD7005W
TEX
[}] [{]
(DISC)
VOL
[]] [[ ]
ENTER
PWR
SRC
(TUNE/TRACK)
MENU
NAVI
MUTE
e[MUTE]
[ENTER]
r[SRC] (PWR)
t[MENU]
u [u]
(SOURCE/POWER)
y[NAVI]
Main Unit
Dimmer sensor ( DIMMER
page 32)
a
(Display Closed)
![TILT]
ASPECT
ASP
TILT
OPEN
q[ASP] (ASPECT)
o[OPEN]
P·MODE
CQ-VD7005W
(P•MODE)
VOL
ENTER
PWR
SRC
MENU
NAVI
MUTE
Note:
¡[ASP], [MENU], [u], [OPEN], [TILT] are available only on the main unit.
: This book refers to connections to the Panasonic car navigation system that will come onto the market in the future. Descriptions
regarding the car navigation system are boxed with a dotted line.
¡Selects the aspect ratio.
¡Activates/inactivates the private mode.
¡Selects a folder or a disc.
¡Selects (vertically) or adjusts an operation
or item.
[ASP]
(ASPECT)
(P•MODE)
q
i[}] [{]
(DISC)
¡Selects or searches for a track, file, sta-
tion.
¡Selects or searches for a channel.
¡Selects (horizontally) or adjusts an opera-
tion or item.
[]] [[]
¡Adjusts the sound volume.
VOL
[
]
w
e
r
(TUNE/TRACK)
¡Mutes the sound temporarily.
MUTE
[
]
¡Switches on/off the power.
¡Changes the modes such as sound and
picture.
[SRC]
(PWR)
¡Selects a band.
¡Shows OSD.
¡Searches for broadcast stations and
memorizes them automatically.
¡Determines an operation or item.
ENTER
[
]
¡Shows the menu screen.
MENU
[
]
t
y
¡Switches navigation mode on and off.
(available in the future)
NAVI
[
]
¡Ejects/reloads a disc.
[
]
u u
¡Opens/closes the monitor.
OPEN
[
]
o
!
(CLOSE)
Note:
¡A disc is in the slot when this is illuminat-
¡Adjusts the monitor position.
¡Tilts the monitor forward temporarily.
TILT
[
]
ed in blue.
10
CQ-VD7005W
Remote Control
Aim the remote control at the remote control sensor of the main unit and operate it.
10
q[SRC] (PWR)
(SOURCE/POWER)
MUTE
r[
]
PWR
MUTE
[+] [–]
t
(VOL)
SRC
VOL
w
ENTER / BAND
[ ] [ ] [
❚❚
]
■
B
[ ] [
s
]
d
y [ ] [
]
}
{
TOP MENU
[
[
] [
]
]
[
RET
RETURN
[RET]
e
(RETURN)
ENT
DVD MENU
] (ENTER/BAND)
[
]
u
CAR AV
(TOP MENU/DVD MENU)
Note:
[ ], [❚❚], [ ],
[ENT], [RET],
¡
[
]
■
B
are available only on the remote control unit.
¡Switches the power on/off.
¡Changes the modes such as sound and
picture.
¡Adjusts the sound volume.
[SRC]
[+] [–]
q
t
(PWR)
(VOL)
¡Selects or searches for a track, file, sta-
y[]] [[]
¡Stops playback.
¡Pause
[ ]
w ■
tion.
¡Selects (horizontally) or adjusts an opera-
[
[
[
]
]
tion or item.
❚❚
¡Selects (vertically) or adjusts an operation
or item.
[}] [{]
¡Playback
B
¡Goes to beginning.
¡Fast forward/fast reverse.
¡Slow playback ([d]).
] [
]
d
s
¡Selects a band.
¡Shows OSD.
¡Searches for broadcast stations and
memorizes them automatically.
¡Determines an operation or item.
[ENT]
(ENTER/
BAND)
¡Returns to the previous display.
¡Inputs the number again.
¡Displays the VCD’s menu.
[RET]
(RETURN)
e
r
¡Displays the DVD/title menu. (Operations
vary according to the media.)
[
]
u
¡Mutes the sound temporarily.
MUTE
[
]
(TOP MENU/
DVD MENU)
11
CQ-VD7005W
Touch Panel Operation Overview
❒ Notes on the Touch Panel
Before operation
¡Clean the surface of the touch panel. (apage 47)
Operation
¡Use only your fingers to operate the touch panel.
¡Do not press the panel forcefully.
¡Do not scratch the panel with fingernails or any
hard objects.
¡Do not use a pen or other sharp implements to
operate the touch panel.
¡Do not bump the front panel.
aFailure to observe the above may damage or
break the glass on the surface of the touch
panel.
11
The State of Operation Screen
Example: DVD mode
Note
:
¡The following picture is partly darkened for explanation.
¡Displaying contents and their positions partly vary with each mode. Refer to the description of each mode for details.
Volume
Current
Disc indicator (apage 17)
Display Button
indicator mode
(Lights when a disc is loaded)
(anext page)
Clock time (apage 30)
Prohibition
Input is not possible because the user has
attempted to perform an operation which
is not supported by the disc contents.
Source Button
(Content varies with each
source)
Menu Button
Displays the Source Selection Screen.
Displays the Menu Screen.
Source Selection Screen
Menu Screen
Source Selection Screen appears.
Touch desired source button.
Menu Screen appears. Select desired setting.
Menu Setting, (apage 28)
Touch
to quit.
Press [SRC] to change to
desired mode.
Press [MENU] to let Menu
Screen appear.
Note
:
¡The screen above appears when no external
device is connected to AV1, AV2, and the
Expansion Module (CY-EM100N, option).
12
CQ-VD7005W
Switching the Display
Please refer to the separate “System Upgrade Guidebook” for how to operate this unit when optional devices are
connected.
12
Touching
allows users to switch between screens as follows.
❏ How to Call up Operation Screen
Source
Standard Screen
Operation Screen
Radio
(apage 24)
Disc Player (DVD/VCD (*1)/
CD/MP3/WMA)
(apage 18)
❏ How to Cancel OSD (On Screen Display)
Source
Standard Screen
OSD OFF *2
AV1/AV2 (*1)
(apage 26)
*1 To switch Operation Screen ON, touch the center of touch panel or press [ENTER].
*2 The operation screen is not available in the video mode.
Note:
¡
Refer to the description of each mode for how to operate the operation screen.
Showing the hidden part of the screen.
Some items have continued parts. You can see the continued parts by pressing
or
.
DVD mode
13
CQ-VD7005W
General
[VOL]
[OPEN]
[TILT]
ASPECT
ASP
TILT
OPEN
P·MODE
CQ-VD7005W
13
VOL
ENTER
PWR
SRC
MENU
NAVI
MUTE
[]] [[ ]
[MUTE]
[SRC] (PWR: power)
Remote Control Sensor
Preparation: Turn your car’s ignition key to the ACC or ON position.
General Operations
Operations
Power
–
–
[SRC]
[SRC]
–
[SRC]
[SRC]
Note:
ON :
You cannot turn on the power via the
¡
remote control when ACC SELECT is set to
OFF . (
Power
ACC SELECT , page 31)
a
OFF :
Display Open/Close
[OPEN]
–
¡Press once to open. Press again to close.
Note:
¡When the display is opened or closed, a loud beep sounds three times.
¡If the unit stops halfway, press [OPEN] again to draw it all the way out.
¡Opening/closing the display can be done when the power is off.
Source selection
[SRC]
[SRC]
RADIO (AM/FM)
(apage 12)
(apage 24)
(apage 18)
(apage 26)
DVD (DVD/VCD (Video CD)/CD/MP3/WMA)
AV1/AV2
Sources connected to the
Expansion Module (CY-EM100N) *
(aSystem Upgrade
Guidebook)
1
1
* When the Expansion Module (CY-EM100N, option) is connected.
(aSystem Upgrade Guidebook)
Note:
¡
If there is no external sources connected, AV1/AV2 mode can be set
to skip. (apage 37)
……
Touch/Press and hold for more than 2 seconds
14
CQ-VD7005W
[SRC] (PWR: power)
[MUTE]
PWR
MUTE
SRC
[+] [–]
VOL
(VOL)
14
ENTER / BAND
ENT
[]] [[]
TOP MENU
RET
RETURN
DVD MENU
CAR AV
General Operations (continued)
Operations
Volume
Note:
¡The sound level for
each source is
stored in memory.
q [+]
w [–]
q Up
w Down
–
w
q
Setting Range: –82 dB to 0 dB, default: –40 dB
Note:
¡The volume level can be set independently for each source and each
disc format.
Mutes the sound.
To cancel, press again.
Mute
[MUTE]
–
[MUTE]
[TILT]
–
–
q Press and hold for more than 2 sec-
Tilt Angle
onds.
Press to adjust. Setup is the same as
from MENU. Refer to DISPLAY UNIT
w
[]] or [[]
[]] or [[]
or
for details. ( page 30)
a
Warning
¡Do not touch the unit while the display is moving. Inserting hands, fingers or for-
eign objects into the unit can cause injuries and damage to the unit.
Note:
¡Vertical angle (TILT) is saved in the memory, so when the display is drawn out next, it
is automatically set at the angle and in the position adjusted before.
¡After adjusting its angle, also adjust the brightness as well. (apage 32)
¡The car model and installation conditions may impose some restrictions on the
adjustment of the monitor's angle.
To raise the display, press again.
[TILT]
Folding Down the
Display
Temporarily
–
–
Note:
¡Even when the unit power is off, you can fold down the display temporarily.
Caution
¡Avoid physical shock to the monitor.
¡Do not place any object on the display, or subject it to undue force.
¡Do not move the display forcibly.
¡The monitor movable range may be limited by the type of car, the position where
the display is mounted, etc.
15
CQ-VD7005W
Before Disc Playback
Discs that can be Played Back
❒ Disc Type
¡Playing back a photo CD disc with this unit could
damage the data that is recorded on the disc.
* CQ-VD7005W2 * CQ-VD7005W3 * CQ-VD7005W4
15
VCD
(Video CD)
DISC
DVD
CD
CD-R/RW
1
2
3
4
* CQ-VD7005W5
Recordable
ReWritable
Mark/logo
Disc Size
❒ Symbols used on jackets
TEXT
(Examples of such symbols include)
12 cm
2
¡
¡
¡
: Number of subtitle languages
: Number of audio tracks
: Number of angles
Video
Format
2
NTSC/PAL
LPCM,
3
LPCM
(CD-DA),
MP3/
MPEG1,
MPEG2,
dts, Dolby
Digital
LPCM
(CD-DA),
dts
The numbers indicate the number of languages,
tracks, angles, etc., recorded on the disc.
Audio
Format
LPCM,
MPEG1
WMA
Screen size (H:V aspect ratio)
(
1)
(
2)
:
2 * , 3 * ,
¡
: 4:3 standard size
4 3
Region
No.
(
3)
(
4)
4 * , 5 * ,
LB
¡
: Letterbox (apage 36)
(ALL)
1
2
3
¡ 16:9 wide size
* CQ-VD7005W2 * CQ-VD7005W3 * CQ-VD7005W4
4
* CQ-VD7005W5
:
16 9 LB
LETTER BOX
: Playback in
format on a
standard screen (4:3).
Note:
:
16 9 PS
¡About CD-Rs/RWs and DVD–Rs/RWs, refer to “Notes on
CD-Rs/RWs and DVD–Rs/RWs”. (apage 48)
¡Some copy-protected music CDs are not playable.
PAN & SCAN
: Playback in
(apage 36)
format on a standard screen (4:3).
Note:
❒ Notes on DVD–Rs/RWs
¡Only video formatted discs are playable. Discs in the
video recording (VR) format are unplayable.
¡Unfinalized discs are unplayable.
¡
The size of the image that is displayed on the screen
depends on the screen mode (“Aspect Ratio”
39), and on the screen size for the content on the
disc.
a
page
¡Some discs are unplayable depending on the disc
itself, device, drive and software that are used for disc
recording.
❒ Region Management Information
This product is designed and manufactured to
respond to the Region Management Information that
is recorded on a DVD disc. If the Region number
described on the DVD disc does not correspond to
the Region number of this product, this product does
not play the disc.
❒ Discs not supported
The following discs are not played back on this
product.
¡DVD-Audio
¡DVD+R
¡SVCD
¡DVD-ROM
¡DVD+RW
¡VSD
¡DVD-RAM
¡CVD
¡CD-G
¡CD-ROM (except MP3/WMA)
Example:
The Region number for
¡CD-RW (except MP3/WMA and CD-DA)
¡CD-R (except MP3/WMA and CD-DA)
¡SACD
¡Hybrid SACD (except CD-DA)
¡Divx Video Discs
¡CD-EXTRA (audio-only playback possible)
(
1)
(
2)
(
1)
*
*
*
this product is “2” * ,
(
2)
(
3)
(
4)
2
4
3
5
“3” * , “4” * , “5” *
¡Photo CD
¡CDV
and “ALL”.
(
3)
(
4)
*
1
* CQ-VD7005W2
2
* CQ-VD7005W3
3
(
1)
* CQ-VD7005W4
¡DVDs with a region number other than “2” * ,
4
(
2)
(
3)
(
4)
* CQ-VD7005W5
“3” * , “4” * , “5” * or “ALL”
ALL
16
CQ-VD7005W
Disc Insert/Eject
■ When a disc is in the player...
16
TILT
CLOSE
Printed side
CQ-VD7005W
TEXT
VOL
[u] (eject)
lights.
ENTER
PWR
SRC
MUTE
MENU
NAVI
Caution
¡When the disc is inserted or ejected, to prevent disc
scratches never exert any downward force on the
disc.
Do not insert a disc when the eject button
because a disc is already loaded.
lights
DVD VCD CD MP3 WMA
DVD VCD CD MP3 WMA
Disc Insert
Disc Eject
¡The mode that supports the disc is selected, and play-
Press [u] to stop playback and eject the disc.
back starts.
(Press [u] again to reload the disc.)
DVD VCD
Note:
¡If you leave a disc in the slot for more than 30 seconds
after its ejection, the disc will be automatically reloaded
after loud beep is energized three times.
¡The audio format is automatically identified.
(apage 16)
¡When the menu screen appears, see “Chapter/title
Selection” on page 20.
DVD VCD
¡Due to limitations of certain discs, some DVD and
VCD (Video CD) discs may not operate as described
in this manual. Refer to the disc jacket for further
details.
When a disc is in the player, change to disc player
mode (CD, MP3, WMA, DVD or VCD (Video CD)) and
playback starts.
¡This unit does not support DVD and VCD (Video
CD) karaoke functions.
Note:
¡Do not insert a disc when the eject button
lights because a disc is already loaded.
¡The power will be turned on automatically when a disc
is loaded.
¡You can play a disc even if the monitor is closed.
DVD VCD
¡The sound may be interrupted for a few moments
while the audio format is being identified.
Caution
¡Do not use irregularly shaped discs.
¡Do not insert foreign object into the disc slot.
17
CQ-VD7005W
Disc Player
Source Button
TILT
CLOSE
(
)
Disc Mode DVD Selection
“
”
Touch Source Button .
q
d
Touch
w
17
(DVD) on the
Source Selection
Screen.
CQ-VD7005W
TEXT
VOL
ENTER
PWR
MUTE
SRC
MENU
NAVI
[SRC]
Press
mode.
to change to the desired
[SRC]
[ENTER]
To switch Operation Screen ON, touch the center of
touch panel or press [ENTER]. (Only for Video Mode)
[]] [[ ]
[}] [{]
Video Mode
DVD
mode display
VCD (Video CD)
mode display
Source Button
Playing time
Source Button
Playing time
Operation Buttons
Operation Buttons
Audio Mode
❒ Folder/File/Track Selection
MP3/WMA
mode display
(Example: MP3 mode)
Source Button Playing time
: Folder
: MP3/WMA file
qTouch
a folder.
,
(folder name) to select
Title/text scroll
: scrolls up/down the file list by
1 page.
,
: scrolls up/down the file list by
1 line.
Operation Buttons
Folder selection
wTouch
(file name) to play.
CD
mode display
qPress []], [[], [}] or [{] to select a
folder.
Source Button Current track
Playing time
[]] [[]: movement among different lev-
els of trees
[}] [{]: movement in the same tree
wPress [ENTER].
Note:
¡It is not possible to display the whole tree and file list
in a folder.
¡The displayed contents on the touch panel vary with
circumstances.
Operation Buttons
CQ-VD7005W
Title/text scroll
18
Basic Operations
Operations
Compatible
Discs
Operations
18
DVD VCD
CD
Track/file Selection
Next track/file
[d]
[[]
Beginning of the current track/file
Previous track/file (Touch/press twice.)
[s]
[]]
MP3 WMA
Note:
DVD
¡When playing a DVD, there are cases where it is not possible to return to
the start of a chapter that spans 2 titles. (apage 50)
DVD VCD
CD
Fast forward
Fast Forward/
Fast Reverse
[d]
[[]
Release to resume playback.
Fast reverse
Release to resume playback.
The speed changes if the button is held down as follows.
Regular speed /1.5 times (DVD) /10 times (DVD) /20 times
[s]
[]]
MP3 WMA
DVD VCD
MP3 WMA
CD MP3 WMA
Folder Selection
Next folder
[}]
[}]
Touch
desired
folder
[{]
[{]
Previous folder
Title/text Scroll
Stop
Scrolls the title/text once
–
–
DVD VCD
CD
To resume playback, touch/press
[3]
–
/ [5].
MP3 WMA
DVD VCD
Pause
To resume playback, touch/press
again or touch/press
CD
–
[y]
/ [5].
MP3 WMA
¡
Touch/press and hold in the pause mode.
Slow Playback
[d]
[[]
Playback is at about 1/3 normal speed.
To resume normal playback, touch/press
/ [5].
DVD VCD
Note:
¡Reverse slow playback is not possible.
DVD VCD
CD
Repeat Play
*
*
–
–
–
To cancel, touch again.
MP3 WMA
Repeat Play within the
Current Folder
To cancel, touch and hold for more
than 2 seconds again.
–
MP3 WMA
CD
Scan Play
–
–
–
To cancel, touch again.
–
–
–
CD
Random Play
*
*
To cancel, touch again.
MP3 WMA
Random Play within the
Current Folder
MP3 WMA
To cancel, touch and hold again.
……
Touch/Press and hold
* Touch panel symbols will change to indicate these current mode.
,
{F= FOLDER (folder)}
19
CQ-VD7005W
Disc Player (continued)
To switch Operation Screen ON, touch the center of touch panel or press [ENTER].
Chapter/title Selection
Operations
Compatible
Discs
Operations
19
[DVD MENU]
Showing menu and
selecting an item
qMenu appears.
–
or
or
1
1
[RETURN]
*
*
d
d
d
DVD
VCD
1 Note on VCD:
For VCD, touch/press
[]] [[]
[}] [{]
d
*
[]] [[]
–*2
d
–*2
wSelect the desired item.
1
*
[}] [{]
[RETURN]
/
instead
d
d
eDetermine the setting.
[ENTER] [ENTER]
[DVD MENU]
of
/
.
–
–
[RETURN]
Returns to the previous display.
Note:
[DVD MENU]
When the top menu does not appear even by pressing
¡
,
press and hold the same button for more than 2 seconds.
qToggles “Chapter number input
Starting Playback
from a specific
chapter/title
mode”, “Title number input mode”
and “Number input mode”.
–
–
d
d
Touch the numerical
key to enter a number
directly
wInput desired number.
–
to
–
DVD
d
d
[ENTER]
[ENTER]
ePlayback starts.
Note:
For retrying selection during number entry, touch/press
[RETURN]
/
.
¡
Note:
If no operation is performed for 8 seconds after you have touched
, the operation buttons disappear.
¡
If the title/chapter number is inputted and no operation is performed for 2 seconds, playback will start from the num-
¡
ber of the title/chapter entered.
*2 On-Screen Direct Operation (Only for DVD)
Some DVDs allow you to operate the DVD menu by
touching the screen.
Showing Source button and Menu button
Press . The Source button and Menu button appear.
In such a case, if your targeted button is located too close
to other buttons, a part of the screen may be enlarged in
order that you can press the button for sure.
Source Button
(apage 12)
Menu Button
(apage 12)
Moving operation buttons (Only for DVD)
When the operation buttons interfere with operations,
press . The buttons are transferred as shown below.
Note:
¡When the current disc is not ready for the on-screen
direct operation, perform operations with the buttons
on the remote control or the unit.
¡The on-screen direct operation of the DVD menu is not
available in the DVD changer mode.
20
CQ-VD7005W
DVD
mode display
20
Repeat play DVD menu
Chapter/title selection
Fast forward/fast reverse
Return
Audio Language/
Angle/
Subtitle Language
Play/stop/pause
Useful Function
Operations
Compatible
Discs
Operations
Subtitle Language
–
–
¡Touch during playback.
DVD
It is possible to change the subtitle language during play if multiple lan-
guages are recorded on the disc.
Note:
¡There may be a brief delay before the subtitles appear.
–
–
¡Touch during playback.
Audio Language
Angle
DVD
DVD
It is possible to change the audio language during play if multiple audio lan-
guages are recorded on the disc.
–
–
¡Touch during playback.
For DVDs which contain scenes which have been shot simultaneously from
a number of different angles the same scene can be viewed from each of
these different angles during play. ( ANGLE MARK
page 36)
a
–
–
Stereo & Monaural
It is possible to switch the audio between stereo sound and monaural sound
(L or R).
VCD
: stereo sound
STEREO
d
: the left channel audio is output on both the left and
right speakers.
MONO.L
d
: the right channel audio is output on both the left and
right speakers.
MONO.R
Note:
If no operation is performed for 10 seconds or
is touched, the operation buttons disappear.
¡
It may not be possible to switch the language unless the unit is at the DVD menu ( previous page) or is at the DVD
¡
a
settings. ( page 36)
a
The language on the DVD settings takes priority when the power is turned on or the disc is loaded.
The number of languages and angles depend on the disc. Some discs have only one language/angle or have no lan-
guage/angle.
¡
¡
21
CQ-VD7005W
Notes on MP3/WMA
What is MP3/WMA?
Display Information
TM
MP3* (MPEG Audio Layer-3) and WMA (Windows Media
Displayed items
¡CD-TEXT
Disc title
Audio) are the compression formats of digital audio. The
former is developed by MPEG (Motion Picture Experts Group),
and the latter is developed by Microsoft Corporation. Using
these compression formats, you can record the contents of
about 10 music CDs on a single CD (This figure refers to data
recorded on a 650 MB CD-R or CD-RW at a fixed bit rate of
128 kbps and a sampling frequency of 44.1 kHz).
¡MP3 (ID3 tag)
Album name
Title and artist name
21
Track title
¡WMA (WMA tag)
Album name
Title and artist name
¡MP3/WMA
Folder name
File name
*MPEG Layer-3 audio coding technology licensed from
Fraunhofer IIS and Thomson.
Displayable characters
¡Displayable length of file name/folder name: within 64 char-
acters. (Unicoded file and folder names are reduced by half
in the number of displayable characters.)
Note:
¡Name files and folders in accordance with the standard of
each file system. Refer to the instructions of writing soft-
ware for details.
¡MP3/WMA encoding and CD writing software programs are
not supplied with this unit.
¡ASCII character set and special characters in each language
can be displayed.
¡Some Cyrillic characters in the Unicode can be displayed.
Points to remember when making MP3/WMA files
Common
¡High bit rate and high sampling frequency are recommend-
ed for high quality sound.
¡Selecting VBR (Variable Bit Rate) is not recommended
because playing time is not displayed properly and sound
may be skipped.
ASCII character set
A to Z, a to z, digits 0 to 9, and the following symbols:
(space) ! ” # $ % & ’ ( ) * + , - . / : ; < = > ? @ [ \ ] ˆ _ ` {
| } ~
¡The playback sound quality differs depending on the encod-
ing circumstances. For details, refer to the instructions of
your own encoding software and writing software.
Note:
¡With some software in which MP3/WMA format files have
been encoded, the character information may not be dis-
played properly.
MP3
¡It is recommended to set the bit rate to “128 kbps or more”
¡Undisplayable characters and symbols will be converted
and “fixed”.
into an asterisk ( ).
¡It is recommended that the length of the file name is less
than 8 (excluding the file extension).
*
WMA
¡It is recommended to set the bit rate to “64 kbps or more”
and “fixed”.
¡Do not set the copy protection on the WMA file to enable
this unit to play back.
Windows Media, and the
Windows logo are trademarks,
or registered trademarks of
Microsoft Corporation in the
United States and/or other
countries/regions.
Caution
¡Never assign the “.mp3”, or “.wma” file name
extension to a file that is not in the MP3/WMA
format. This may not only produce noise from
the speaker damage, but also damage your
hearing.
22
CQ-VD7005W
Recording
R
M
ec
P
o
3
rd
/
i
W
ng
M
M
A
P3
f
/
i
W
le
M
s
A
o
f
n
ile
a
s o
C
n
D
a
-mCD
e
-mdiedia
a
¡You are recommended to minimize the chances of making
a disc that contains both CD-DA files and MP3/WMA files.
¡If CD-DA files are on the same disc as MP3 or WMA files,
the songs may not play in the intended order, or some
songs may not play at all.
¡You may encounter trouble in playing MP3/WMA files or
displaying the information of MP3/WMA files recorded with
certain writing software or CD recorders.
¡This unit does not have a play list function.
¡Although Multi-session recording is supported, the use of
Disc-at-Once is recommended.
22
¡When storing MP3 data and WMA data on the same disc,
use different folders for each data.
¡Do not record files other than MP3/WMA files and unneces-
sary folder on a disc.
¡The name of an MP3/WMA file should be added by rules as
shown in the following descriptions and also comply with
the rules of each file system.
Supported file systems
ISO 9660 Level 1/Level 2, Apple Extension to ISO 9660, Joliet,
Romeo
Note:
¡The file extension “.mp3” or “.wma” should be assigned to
each file depending on the file format.
¡Apple HFS, UDF 1.50, Mix CD and CD Extra are not support-
ed.
Compression formats (Recommendation: “Points to remember when making MP3/WMA files” on the previous page)
Compression method
Bit rate
VBR
Yes
Yes
Yes
Sampling frequency
32, 44.1, 48 kHz
16, 22.05, 24 kHz
32, 44.1, 48 kHz
MPEG 1 audio layer 3 (MP3)
MPEG 2 audio layer 3 (MP3)
32 k – 320 kbps
8 k – 160 kbps
Windows Media Audio Ver. 2, 8, 9* 32 k – 192 kbps
* WMA 9 Professional/LossLess/Voice are not supported.
Folder selection order/file playback order
Maximum number of files/folders
Root Folder
1
(Root Directory)
¡Maximum number of files: 511 (file and folders)
¡Maximum number of files in one folder: 255
¡Maximum depth of trees: 8
2
4
q
Folder Selection
3
¡Maximum number of folders: 255 (Root folder is included.)
w
r
1
8
In the order
–
e
File Selection
Note:
In the order
–
5
6
¡You can shorten the duration between data read and play-
back by decreasing the quantity of files or folders, or the
depth of the hierarchy.
q
y
¡This unit counts the number of folders irrespective of the
presence or absence of an MP3/WMA file.
7
t
y
8
¡If the selected folder does not contain any MP3/WMA files,
the nearest MP3/WMA files in the order of playback will be
played.
Tree 1
Tree 2
Tree 3
Tree 4
Tree 8
(Max.)
¡Playback order may be different from other MP3/WMA
players even if the same disc is used.
¡“ROOT” appears when displaying the root folder name.
Copyright
No warranty
The above description complies with our investigations as of
December 2006. It has no warranty for reproducibility and
displayability of MP3/WMA.
It is prohibited by copyright laws to copy, distribute and
deliver copyrighted materials such as music without the
approval of copyright holder except enjoying yourself
personally.
23
CQ-VD7005W
Radio
Auto presetting
Radio Mode Selection
Frequency Preset stations
Source Button
TILT
CLOSE
“
”
Touch Source Button .
q
d
Touch
w
23
Band
(RADIO) on the
Source Selection
Screen.
selection
CQ-VD7005W
TEXT
VOL
[SRC]
Press
mode.
to change to the desired
ENTER
PWR
SRC
MUTE
MENU
NAVI
1
* List selection
[SRC]
To switch Operation Screen ON, touch
.
[ENTER]
Tuning
[]] [[ ]
1
* Appears when ALL is selected. ( page 38)
a
Stereo indicator
MENU
RADIO
FM SETUP
AUTO PRESET
EACH
/
ALL
e
e
e
e
Tuning
Operations
2
2
* The displayed contents on the
touch panel vary with circum-
stances.
Band Selection
*
[BAND]
[ENTER]
FM 1
FM 2
FM 3
AM
Preparation:
Select ALL . ( page 38)
a
List Selection
Refer to the next page.
MENU
RADIO
FM SETUP
AUTO PRESET
EACH
/
ALL
e
e
e
e
2
2
*
* The displayed contents on
the touch panel vary with
circumstances.
[BAND]
[ENTER]
3
LIST 1
LIST 2
LIST 3
AM
*
There are 6 stations in each list. You can call up next 6 stations by switching from one
list to another.
3
* From the touch panel, you can toggle only Lists 1-3, but not AM . To change to AM
,
touch
.
[
[
]
]
[
[
]
]
Up
[
[
Station
Selection
Down
]
]
Seek Tuning
[
[
]
]
[
[
]
]
Up
[
[
Down
]
]
Touch/press and hold for more than 0.5 second then release. Seeking starts.
Touch/Press and hold
……
24
CQ-VD7005W
Preset Memory
Select a band and frequency.
Manual Preset
Memory
Up to 6 stations can be
preset in each band.
to
24
–
–
blinks once
¡Touch/press and hold for more than 2 seconds.
¡The frequency blinks once, and a receiving station is saved in the memory.
New stations overwrite existing saved stations.
Auto Preset
Memory
Preparation:
Select EACH . ( page 38) (default: EACH
)
a
MENU
RADIO
FM SETUP
AUTO PRESET
EACH
/
ALL
e
e
e
e
A
Six stations are automati-
cally preset in each band.
Select a band.
6 stations with first to 6th highest in signal
strength of each band will be preset.
[ENTER]
[BAND]
¡Touch/press and hold for more than 2 seconds.
¡Once set, the preset stations are sequentially scanned for 5 seconds each. (scanning)
New stations overwrite existing saved stations.
B
In total 18 FM stations are
automatically preset.
Preparation:
Select ALL . ( page 38)
a
MENU
RADIO
FM SETUP
AUTO PRESET
EACH
/
ALL
e
e
e
e
18 stations with first to 18th highest in signal
strength of all FMs will be preset at once.
[ENTER]
[BAND]
¡Touch/press and hold for more than 2 seconds.
¡Once set, the preset stations are sequentially scanned for 5 seconds each. (scanning)
New stations overwrite existing saved stations.
Select a band or a list.
Preset Station
Calling
to
–
–
¡Touch desired preset button.
Preparation:
Select ALL . ( page 38)
a
Preset Swap
MENU
RADIO
FM SETUP
AUTO PRESET
EACH
/
ALL
e
e
e
e
A station preset is inter-
changeable with another
station preset.
qSelect the list and the preset number that contains the station to be interchanged
(see “Preset station calling” above).
w Select the list and hold down the preset number that contains the targeted channel
for more than 2 seconds.
The preset station selected in the step qis
interchanged with the targeted preset chan-
nel selected in the step w(Preset Swap).
to
–
–
……
Touch/Press and hold
25
CQ-VD7005W
AV1/AV2
Please refer to the separate “System Upgrade Guidebook” for how to operate this unit when optional devices are
connected.
Preparation:
¡Connect an optional external device to the AV1/AV2.
25
Source Button
AV Mode Selection
You can view the images and listen to the sounds from
the connected external devices in the AV1/AV2 mode
respectively.
TILT
CLOSE
“
”
Touch Source Button .
q
d
Touch
/
w
(AV1/AV2) on the
Source Selection
Screen.
CQ-VD7005W
TEXT
VOL
ENTER
PWR
MUTE
SRC
MENU
NAVI
[SRC]
[ENTER]
[SRC]
Press
mode.
to change to the desired
To switch Operation Screen ON, touch the center of
touch panel or press [ENTER].
Note:
You can set up the system so that the AV mode is not
¡
selected (source skip). ( page 37) (AV set to NAVI
a
INPUT is not skipped even if SOURCE SKIP is set to
ON
)
If no operation is performed for 10 seconds or
¡
touched, the operation buttons disappear.
is
AV terminal is not used for the Panasonic car
¡
navigation system (available in the future). Refer to
NAVI SETUP for setting. ( System Upgrade
a
Guidebook)
26
CQ-VD7005W
26
27
CQ-VD7005W
Settings
Preparation:
To display menu in Chinese, Execute MENU DISPLAY (Language setting). ( page 31)
a
USER
DISPLAY UNIT
CLOCK
ID-CODE
MEMORY CLEAR
OTHER
User
Display adjustment
Clock setting
ID Code Setting
Memory clearance
Other settings
(a
(a
(a
(a
(a
page 30)
page 30)
page 30)
page 31)
page 31)
27
SCREEN
DIMMER
PICTURE
Screen
Adjusting the brightness
Display appearance
(
(
a
a
page 32)
page 32)
AUDIO
Audio
SOUND SETUP
GRAPHIC-EQ
CS Auto
SP SETUP
SP LEVEL
TIME ALIGNMENT
SOURCE LEVEL
CROSS OVER
Sound setting
Setting and adjusting of graphic equalizer
CS Auto setting
Setting of the absence/presence of each speaker
Adjusting the output balance of each speaker
Delay time setting of each speaker
Setting the AV1/AV2 input level
Cut off frequency
(a
(a
(a
(a
(a
(a
(a
(a
page 32)
page 32)
page 33)
page 34)
page 34)
page 35)
page 35)
page 35)
DVD
LANGUAGE
DISPLAY
DVD SOUND
MULTI-CH
DVD
Language Setting
Appearance of DVD image
DVD sound setting
Sound output selection
(a
(a
(a
(a
page 36)
page 36)
page 37)
page 37)
INPUT/OUTPUT
NAVI SETUP
SOURCE SKIP
INPUT SELECT
OUTPUT SELECT
H-F SETUP
Input/output
Navigation setting
Source skip
Input selection
Output selection
Hands-free setting
(*1)
page 37)
(*1)
(*1)
(*1)
(a
RADIO
FM SETUP
AM SETUP
Radio
Setting for FM stations
Setting for AM stations
(
(
a
a
page 38)
page 38)
(*1) Please refer to the System Upgrade Guidebook.
28
CQ-VD7005W
❏ MENU Operation
(Example: DVD mode)
q
w
28
Touch desired setting.
Touch
in Operation Screen.
e
(Example: setting screen of “DISPLAY UNIT” apage 30)
Determines the setting and goes back to the pre-
vious menu out of the menu.
Determines the setting and gets out of the menu.
Note:
¡The display returns to the previous status if there is no operation for more than 60 seconds after changing to the set-
ting menu.
CQ-VD7005W
TEXT
VOL
ENTER
PWR
RC
S
M
E
NU
NAVI
MUTE
[SRC]
(Exit from the menu)
[MENU]
(Shows the menu display/
Goes back to the previous
menu)
[ENTER]
(Determine)
[]] [[ ]
[}] [{]
(Select/adjust)
29
CQ-VD7005W
Settings (continued)
USER
SCREEN AUDIO
DVD
INPUT/OUTPUT RADIO
DISPLAY UNIT
ID-CODE
29
Display adjustment
ID Code Setting
Prior to operating this unit, it is advisable to assign a 4-
digit ID code for security. Once the ID code has been set,
the unit cannot be operated if the main power supply is
disconnected then re-connected. It is electronically locked
so that a thief cannot use the stolen unit unless that per-
son knows the code you have set.
(Tilt angle adjustment)
TILT
1
2
3
4
5
1
5
The ID code operation must be performed only by the
person to whom the unit belongs.
default:
5
Generally, it is not necessary to enter the ID code each
time when using the unit if it has not been disconnected
from the main power supply (car battery).
(Monitor setting when power on)
OPEN/CLOSE
AUTO
: the monitor is opened automatically
when turning ON ACC.
0
9
to
4 digits numeric code
MANUAL
: the monitor is not opened automatically.
default: MANUAL
default: none
How to set your ID code (for the first time)
q Enter an 4 digit ID code.
w Enter the same 4 digit ID code again.
Note:
¡The monitor position setting menu can also be dis-
played by pressing the [TILT] button on the main unit
for more than 2 seconds. (apage 15)
How to change your ID code
q Enter the preset (old) 4 digit ID code. If the wrong ID
code is entered, a new ID code cannot be registered.
w Enter a new 4 digit ID code.
CLOCK
e Enter the new 4 digit ID code again.
Clock setting
How to cancel the known ID code
(Clock display)
DISPLAY
Enter the preset (old) 4 digit ID code. If the wrong ID
code is entered, it is not possible to cancel the ID code
function.
q
ON
: clock display ON (“0:00” is displayed
before adjusting the clock.)
Touch and hold
until “COMPLETED!” is dis-
w
played. The ID code cancelling procedure is completed.
The unit now works without an ID code.
OFF
: clock display OFF
default: OFF
Note:
¡Should your unit ever require service, cancel your ID
code before sending for repair.
(Hour adjustment)
HOUR ADJUST
¡The ID code setting cannot be eliminated even by the
memory clear function.
¡The inputted code is not displayed for your security.
]
: puts back hour.
[
: puts forward hour.
(Minute adjustment)
MINUTE ADJUST
Caution
]
¡Record your registered ID code and keep it in a
secure location. (Fill in the ID code memo (a
page 46).) If you forget it, you will be unable to
use the unit. In case you forget the ID code,
please consult your nearest Panasonic Service
Center.
: puts back minute.
[
: puts forward minute.
Note:
[SRC]
/ .
To start the clock, touch/press
¡
Set the Daylight Saving Time manually.
¡
default: HOUR ADJUST: 0
MINUTE ADJUST: 0
30
CQ-VD7005W
MEMORY CLEAR
OTHER
30
Memory clearance
Other settings
The state of all of the current memories are returned to
default settings.
(Beep setting)
BEEP
Note:
ON
: operation sound (beep) ON
: operation sound (beep) OFF
¡The ID code is not deleted by executing memory clear.
OFF
: clears the memory to default settings.
YES
NO
default: ON
: no memory clear.
The display returns to the previous one.
(Setting ACC selection ON and
OFF)
ACC SELECT
ON
: sets to ON if your car has ACC position.
OFF
: sets to OFF if your car has no ACC posi-
tion.
REALLY? appears when
YES is selected.
default:
ON
Note:
¡
: proceed.
OK
For an ACC-equipped car, select ON. The following
functions are available.
: no memory clear.
CANCEL
The power is turned on automatically when inserting
a disc or magazine.
¡
Caution
OFF selection disables turning on the power of the
¡
¡Be aware that this setting restores the unit to default
settings, so that all the memories and settings that
you have set will be eliminated.
main unit through the remote control.
Caution
¡Be sure to select OFF when your car has no ACC
position in the ignition switch. Failure to do this
could cause the battery to go dead.
OFF
ACC
IGN
(Remote control setting)
REMOTE CONTROL
FRONT
REAR
: main unit-specific remote control
: rear monitor (option)-specific remote
control
default: FRONT
(Language setting)
MENU DISPLAY
ENGLISH
CHINESE
: displays the menu in English.
: displays the menu in Chinese.
default: ENGLISH
31
CQ-VD7005W
Settings (continued)
SCREEN
AUDIO
USER
AUDIO DVD
INPUT/OUTPUT RADIO
USER SCREEN
DVD
INPUT/OUTPUT RADIO
(Display)
SOUND SETUP
DIMMER
Sound Set Up
31
Adjusting the brightness
(Sound effect setting)
SOUND EFFECT
: automatically adjusted according to
ambient light intensity.
AUTO
THROUGH
GEQ
: no GEQ or CS Auto setting
1
2
3
4
: goes to GEQ (GRAPHIC-EQ) setting
Darker
Brighter
CS Auto
: goes to CS Auto setting
default: THROUGH
default: AUTO
(Graphic-equalizer)
PICTURE
GRAPHIC-EQ
Display appearance
CONTRAST
]
Graphic-equalizer
Six EQ presets are already provided at shipment in this
unit. To recall a preset memory, select the correspon-
ding preset buttons [1] to [6].
(Adjust the image contrast)
: decreases the contrast between black and white.
: increases the contrast between black and white.
1
2
3
4
5
6
: (Flat) flat frequency response
: (Rock) speedy and heavy sound
: (Pop) wide-ranged and deep sound
: (Vocal) clear sound
[
(Adjust the image brightness)
BRIGHT
]
[
: (Jazz) jazz-specific deep sound
: (Club) club and disco-specific sound
: darkens.
: lightens.
You may set your own EQ or modify factory preset-
tings in each memory button by following the instruc-
tions below:
(Adjust the image color depth)
COLOR
]
[
Adjusting level of each preset
: lightens the depth of color on the display.
: deepens the depth of color on the display.
The level of each of the 7 frequency bands can be
adjusted.
Select the preset number that you prefer to adjust.
q
[
][
]
Touch/press
quency.
/
to adjust each fre-
w
{ }
(Adjust the image tone or tint)
TINT
Touch/press the same preset number for more than
2 seconds.
e
]
[
: emphasizes red in the color image.
: emphasizes green in the color image.
Frequency band
60 160 400 1 k 3 k 6 k 16 k
(Hz)
Adjustment range: –12 dB to +12 dB (in 2 dB steps)
default: 0 dB for each band
Note:
The new level adjustment will overwrite the previous
¡
level adjustment.
For resuming the factory settings, touch and hold
¡
(INIT (initialize)) for more than 2 seconds.
32
CQ-VD7005W
To set the level to flat, touch and hold
for more than 2 seconds.
(flat)
¡
(TruBass Setting)
TruBass
32
Expectable effects vary with the audio format to be
¡
used, settings in the menu, and other factors.
(Applies to the front speakers)
FRONT TruBass
[
: more
]
: less
(Applies to the rear speakers)
(Applies to the Sub-woofer)
REAR TruBass
[
: more
]
: less
CS Auto
SUB-W TruBass
CS Auto Setting
[
: more
(Customizing the setting)
(Raises the sound image)
SELECT
]
: less
FOCUS
Setting range: off, +1 to +10
default: off
(Raises the front sound image)
(Raises the rear sound image)
(Raises the central sound image)
FRONT FOCUS
Note:
¡TruBass®
[
: more
TruBass is an audio technology to which the technique of
bass sound reproduction used in pipe organs is electri-
cally applied, and in which an equalizer is not used at all
and bass sound from the speakers to be used is richly
reproduced.
]
: less
REAR FOCUS
[
: more
]
: less
(Adjusts the SRS effect)
Mixing
CENTER FOCUS
FRONT TO REAR Mixing (Adjusts the SRS effect (front)
on rear speakers)
[
: more
[
: more
]
: less
]
: less
Setting range: off, +1 to +10
default: off
CENTER TO REAR Mixing (Adjusts the SRS effect (center)
Note:
¡FOCUS®
on rear speakers)
Focus is an audio technology that moves the sound
image of playing sound vertically to reproduce the
sounds of instruments and voices clearly.
[
: more
]
: less
Setting range: off, +1 to +10
default: +5
33
CQ-VD7005W
Settings (continued)
(AUDIO continued)
(Phase setting)
PHASE
(Speaker set up)
SP SETUP
33
Setting the absence/presence and size of each speaker
: subwoofer phase 0 degree
0°
(Front speaker setting)
: subwoofer phase 180-degree inverted
180°
FRONT
Note:
This setting is feasible only when SUB-W is set to
: for small speakers, or when bass playback
is not possible
SMALL
¡
YES
.
: for large speakers, when bass playback is
possible (at least 100 Hz or lower)
LARGE
default:
0°
default:
LARGE
(Speaker level)
SP LEVEL
(Center speaker setting)
CENTER
Adjusting the output balance of each speaker
(Left front speaker output bal-
ance)
: when not using a center speaker
NONE
FRONT L
: for small speakers, or when bass playback
is not possible
: for large speakers, when bass playback is
possible (at least 100 Hz or lower)
SMALL
]
]
]
]
]
]
[
: down,
: up
: up
: up
: up
: up
: up
LARGE
(Center speaker output bal-
ance)
CENTER
default:
NONE
[
: down,
* A center speaker (option, EAB-CF2 recommended) is
required.
(Right front speaker output
balance)
FRONT R
(Surround speaker setting)
SUR
[
: down,
(Right surround speaker out-
put balance)
: when not using a surround speaker
NONE
¡
R SUR
: for small speakers, or when bass playback
is not possible
: for large speakers, when bass playback is
possible (at least 100 Hz or lower)
SMALL
[
: down,
LARGE
(Left surround speaker output
balance)
¡
L SUR
default:
LARGE
[
: down,
(Subwoofer speaker output
balance)
(Subwoofer speaker setting)
SUB - W
SUB - W
[
: when using a subwoofer
: when not using a subwoofer
YES
NO
: down,
Setting range: –10 dB to +10 dB (1 dB steps)
default: 0 dB for all speakers
default:
NO
* A subwoofer (option, CJ-SW3003 recommended) is
required. A power amplifier (option) is also required for
connecting a subwoofer.
If the speaker setting is
test signal is not output and that speaker cannot be
selected.
or
for a speaker, the
NO
¡
NONE
[+] [–]
or
press
¡Turn rotary volume controller or
Note:
(VOL) to adjust the volume of the test signal.
While the private mode is active, only
¡
FRONT
can be
adjusted.
34
CQ-VD7005W
Note:
While the private
mode is active, only
¡
SOURCE LEVEL
34
Setting the AV1/AV2 input level
FRONT L
and
Make this setting if it is not possible to adjust the volume
through the connected device (on the output side).
FRONT R
can be
adjusted.
(Setting for AV1)
AV1 LEVEL
(Test tone output)
TEST TONE
: sets the level low/sound volume increases.
LOW
HIGH
ON
: enables the test tone.
: disables the test tone.
: sets the level high/sound volume decreases.
default: HIGH
OFF
default:
OFF
(Setting for AV2)
AV2 LEVEL
When the test tone is set to on, test signal (a continu-
ous tone) is output from each speaker for approximately
2 seconds.
Adjust the output balance so that the tone appears to
have the same volume from each speaker.
¡
: sets the level low/sound volume increases.
: sets the level high/sound volume decreases.
LOW
HIGH
Note:
If the input level from AV1/AV2 is too high, the audio
¡
Adjusting the output balance:
will not be output normally.
Adjust the volume of all of the other speakers to the vol-
ume level of the speaker from which the test signal
appears to be the quietest.
After setting the input level
¡
[+] [–]
or
The volume can be adjusted by pressing
(VOL) on the remote control or turning rotary volume
controller on the unit.
TIME ALIGNMENT
default: HIGH
(Delay time setting of each speaker)
Adjusting the timing with which the audio from each
speaker reaches the listener’s position
(Center speaker delay time set-
CROSS OVER
CENTER
Cut off frequency
ting)
(Sub-woofer Low Pass Filter)
LPF CUT OFF
]
[
: down,
: up
]
[
: down,
: up
Setting range: 0 ms to 5 ms (1 ms steps)
1 ms = 0.001 seconds
Setting range: 63 Hz to 200 Hz
default: 125 Hz
default: 0 ms
(Surround speaker delay time
setting)
SUR
(High Pass Filter)
HPF CUT OFF
]
[
: down,
: up
]
[
: down,
: up
Setting range: 0 ms to 15 ms (1 ms steps)
1 ms = 0.001 seconds
Setting range: off, 63 Hz to 200 Hz
default: off
default: 0 ms
Make this adjustment while listening to sound.
If the speaker setting is NONE for a speaker, that
speaker cannot be selected.
When “PRO LOGIC” is displayed, 15 ms are automatically
added to the delay time setting for the surround speakers.
¡
¡
Note:
This setting is not available if CS Auto is set to ON
HPF CUT OFF is enabled only on the front speakers
(R/L) and rear speakers (L/R).
.
¡
¡
¡
35
CQ-VD7005W
Settings (continued)
DVD
USER
SCREEN AUDIO
INPUT/OUTPUT RADIO
LANGUAGE
DISPLAY
Language Setting
Display aspect and DVD software mode
(Display aspect setting)
35
(DVD menu language)
MENU
DVD ASPECT
: English
: Chinese
: French
: plays a video in 4:3 screen.
: plays a video in wide screen (16:9).
default: WIDE
ENG
CHN
FRA
NARROW
WIDE
: other language. Input the language code.
OTHER
(apage 49)
(DVD software mode)
LETTER BOX
default: ENG
: plays wide-screen video in Pan & Scan
mode (in which the left and right edges
of the screen are cut off).
PAN & SCAN
(Subtitle language)
SUBTITLE
Note:
: plays wide-screen video in letterbox
mode (in which black bands appear at
the top and bottom of the screen).
LETTER BOX
¡A disc supporting closed captioning and subtitles may
overlap each other on the screen. In this case, turn the
subtitle off.
default: PAN & SCAN
: English
: Chinese
: French
ENG
CHN
FRA
Note:
Set the software setting according to the symbol used
¡
¡
¡
on jacket. ( page 16)
a
: other language. Input the language code.
(apage 49)
OTHER
DVD software mode setting is ignored if PAN & SCAN
or LETTER BOX is already set in the software.
Screen aspect of the display unit is changed according
to the aspect ratio setting ( page 39) and DVD soft-
default: ENG
a
ware’s aspect.
(Audio language)
AUDIO
(AV-OUT terminal setting)
Note:
TV TYPE
¡These adjustments being executed, playback will start
from the beginning of a disc.
: sets PAL in accordance with the equip-
ment connected to AV-OUT.
: sets NTSC in accordance with the
equipment connected to AV-OUT.
PAL
: English
: Chinese
: French
ENG
CHN
FRA
NTSC
default: PAL
: other language. Input the language code.
OTHER
(apage 49)
(Angle mark setting)
default: ENG
ANGLE MARK
The angle mark is displayed to indicate the parts where
multi-angle data is recorded.
: activates angle mark.
: inactivates angle mark.
ON
OFF
default: ON
36
CQ-VD7005W
INPUT/OUTPUT
USER
SCREEN AUDIO DVD
RADIO
(Navigation set up)
DVD SOUND
NAVI SETUP
DVD sound setting
(aSystem Upgrade Guidebook)
36
(5.1 channel listening in Dolby
surround sound)
PRO LOGIC
SOURCE SKIP
Source skip
: activates Pro Logic.
: inactivates Pro Logic.
ON
OFF
(AV1 skip)
AV1 SKIP
If AV1 is not used, the AV1 mode is skipped when chang-
ing the mode.
default: OFF
Note:
: skips AV1.
ON
This setting is enabled only in the DVD/VCD/CD player
¡
mode.
: does not skip.
OFF
ON selection in some audio settings may disable
¡
default: OFF
audio output from the subwoofer.
(AV2 skip)
(To use the down mix function,
specify the type.)
AV2 SKIP
DOWN MIX
If AV2 is not used, the AV2 mode is skipped when chang-
ing the mode.
: simple stereo down mix
(Lo = Left only, Ro = Right only)
Lo/Ro
Lt/Rt
: skips AV2.
ON
: surround element decodable down mix
(Lt = Left total, Rt = Right total)
: does not skip.
OFF
Note:
default: OFF
This function is available only when “Dolby Digital” or
“dts” source is playing and when sound comes out
only from the front speakers adjusted with
¡
Note:
When external devices are connected to this unit with-
¡
.
SP SETUP
out involving the Expansion Module (CY-EM100N,
option),
is not enabled because the con-
AV2 SKIP
default: Lt/Rt
nected external devices are identified as AV2.
(Dynamic Range Compression)
INPUT SELECT
DR COMP
(aSystem Upgrade Guidebook)
Maintaining the ambience even while listening at a low
volume level
OUTPUT SELECT
(aSystem Upgrade Guidebook)
Compression style selecting
: DR COMP ON
STD
MIN
H-F SETUP
: made with the greatest compression,
roughly equivalent to a TV broadcast.
(aSystem Upgrade Guidebook)
: DR COMP OFF
OFF
default: OFF
(Multiple channel)
MULTI-CH
Sound output of Dolby Digital 2 ch. from all speakers
: changes sound from 2 ch. to 5.1 ch.
: keeps the source output 2 ch. sound.
ON
OFF
default: OFF
37
CQ-VD7005W
Settings (continued)
RADIO
USER
SCREEN AUDIO DVD INPUT/OUTPUT
FM SETUP
Setting for FM stations
37
(FM IF filter switching)
NOISE SUPPRESSION
AUTO
: adjusted automatically
NARROW
: narrows the frequency bandwidth to be
received to prioritize noise reduction.
WIDE
: widens the frequency bandwidth to be
received to prioritize sound quality.
default:
AUTO
(Auto preset setting)
AUTO PRESET
EACH
ALL
: saves the preset stations in each band.
: saves the preset stations in all FM lists
regardless of band.
default:
EACH
AM SETUP
Setting for AM stations
(Noise suppression)
NOISE SUPPRESSION
: narrows the frequency bandwidth to be
received to prioritize noise reduction.
NARROW
: goes between NARROW and WIDE
.
MID
: widens the frequency bandwidth to be
received to prioritize sound quality.
WIDE
default: MID
38
CQ-VD7005W
Other Settings
[ASP]
TILT
CLOSE
38
CQ-VD7005W
TEXT
VOL
ENTER
PWR
MUTE
SRC
MENU
NAVI
Note:
❑ Aspect Ratio
¡This adjustment is common to video mode.
Default: NORMAL
Mode: 4 types
¡
You cannot change the aspect in the menu screen and a
screen in the CD, MP3/WMA, radio and CD changer
mode. These are fixed to “FULL” as well as a Navigation
Image.
Press and hold [ASP] on the display unit to change the
aspect ratio as follows.
¡When the rear view camera is in operation with the
transmission gear shift in the reverse position, the
image is shown on the “FULL” screen only.
¡In some cases, the picture looks different from the
original one due to your selection of aspect.
NORMAL
¡The conventional display
image has a 4 to 3 ratio of
horizontal to vertical.
¡In this case, a blank area
remains on the right and left
sides of the display.
Caution
¡This is to remind you that compression or extension
of the screen using the aspect ratio (screen mode)
changing function of this product for commercial
purpose of profit making or viewing/listening by the
public could infringe on the rights of the author pro-
tected by the copyright law.
FULL
¡The screen is extended hori-
zontally as a whole to the
aspect ratio of 16 to 9.
¡The extension ratio is the
same at any point of the
¡If you expand normal picture (4 to 3) by using
“JUST”, “ZOOM” or “FULL” aspect to the full of the
screen, you might not see the periphery of the pic-
ture, or you might see a distorted picture.
Therefore, use the “NORMAL” mode to see the orig-
inal picture as the author intended it.
screen.
ZOOM
¡The screen is fully extended at
the normal aspect ratio of 4 to
3.
¡The top and bottom of the
screen are slightly cut.
JUST
¡The screen is extended hori-
zontally to the aspect ratio of
16 to 9.
¡The extension ratio increases
toward the right and left ends
of the screen.
39
CQ-VD7005W
Settings (continued)
Other Settings (continued)
[ASP] (P•MODE)
TILT
CLOSE
39
CQ-VD7005W
TEXT
VOL
ENTER
PWR
MUTE
SRC
MENU
NAVI
❑ Private Mode
Note:
You can mute the sounds from the rear speakers if nec-
essary. Activation of the private mode allows you to enjoy
the front monitor and rear monitor independently with
different sources at the same time.
Be sure to set to OFF when you do not use the private
mode.
¡
¡It is not possible to choose and set the
page 33) and
(a
CS Auto
(
page 35) on the
a
TIME ALIGNMENT
sound setting menu while private mode is active.
Default: Private mode off
“P • MODE” indicator
lights when the
Private Mode is acti-
vated.
Private mode
Private mode
Off
On
Radio
Radio
Press and hold [ASP] (P•MODE) on the main unit for
more than 2 seconds to activate the private mode func-
tion or inactivate it in turn.
DVD
DVD
Radio
Mute
40
CQ-VD7005W
Troubleshooting
❑ If You Suspect Something Wrong
Warning
Check and take steps as described below.
¡Do not use the unit in an irregular condi-
tion, for example, without sound, or with
smoke or a foul smell, which can cause
ignition or electric shock. Immediately stop
using the unit and consult your dealer.
¡Never try to repair the unit by yourself
because it is dangerous to do so.
If the described suggestions do not solve the problem, it is rec-
ommended to take the unit to your nearest authorized Panasonic
Service Center. The product should be serviced only by qualified
personnel. Please refer checking and repair to professionals.
Panasonic shall not be liable for any accidents arising out of neg-
lect of checking the unit or your own repair after your checking.
Never take measures especially those other than indicated by
italic letters in “Possible Solution” described below because
those are too dangerous for users to handle themselves.
40
■ Common
Possible cause
Possible solution
Problem
a
The power cord (battery, power and ground) is connected in the wrong way.
aCheck the wiring.
No power to the unit
Fuse blows out.
aEliminate the cause of fuse blowout and replace the fuse with new one.
Consult your dealer.
MUTE is set to ON.
aSet MUTE to OFF.
Sound is not
generated.
The wiring of speaker lines is not correct, or a break or poor contact arises.
aCheck the wiring in accordance with the wiring diagram. (Installation
Instructions)
There is an electromagnetic-wave generator such as a cellular phone near the unit
or its electrical lines.
aKeep the electromagnetic-wave generator such as a cellular phone away
from the unit and the wiring of the unit. In case noise cannot be eliminated
due to the wiring harness of the car, consult your dealer.
Noise
The contact of the ground lead is poor.
aMake sure that the ground lead is connected to an unpainted part of the
chassis securely.
Alternator noise comes from the car.
aChange the wiring position of the ground lead.
aMount a noise filter.
Noise is made in step
with engine revolutions.
Some operations are not executable in particular modes such as menu mode.
aRead the operating instructions carefully and cancel the mode. If the unit is
still out of order, consult your dealer.
Some operations are not
executable.
There is a break, a short circuit, poor contact or wrong wiring regarding the
speaker wiring.
aCheck the speaker wiring.
No sound from
speaker(s)
The speaker channels
are reversed between
right and left.
The speaker wiring is reversed between right and left.
aPerform the speaker wiring in accordance with the wiring diagram.
The power of the unit
fails unintentionally.
The safety device works.
aConsult your dealer, or your nearest Panasonic Service Center.
41
CQ-VD7005W
Troubleshooting (continued)
■ Radio
Antenna installation or wiring of antenna cable is faulty.
aCheck whether the antenna mounting position and its wiring are correct. In
addition, check to see whether the antenna ground is securely connected to
the chassis.
Poor reception or noise
41
No power is supplied to the antenna amplifier (when using a film antenna, etc.).
aCheck the wiring of the antenna power lead.
The number of auto
preset stations is less
than 6.
The number of receivable stations is less than 6.
aMove to an area where receivable stations number is maximum, and try
presetting.
The contact of the battery lead is poor, or the battery lead is not always powered.
aMake sure that the battery lead is connected securely, and preset stations
again.
Preset stations cannot
be stored.
■
CD
The disc is inserted upside down.
aInsert a disc correctly.
No playback or disc
ejected
There is a flaw or foreign object on the disc.
aRemove the foreign object, or use a flawless disc.
There is a flaw or foreign object on the disc.
aRemove the foreign object, or use a flawless disc.
Sound skipping or noise
The unit is not sufficiently secured.
aSecure the unit to the console box.
Sound skipping due to
vibration
The unit is tilted at over 30˚ in the front-to-end direction.
aMake the angle 30˚ or less.
Something such as a peeled label obstructs the disc coming out.
aPress and hold the [u] for more than 10 seconds (disc forced ejection). In
case that the disc forced ejection does not work, consult your dealer.
Disc unejectable
The microcontroller in the unit operates abnormally due to noise or other factors.
aUnplug the power cord and plug it again. In case the unit is still out of
order, consult your dealer.
42
CQ-VD7005W
■ MP3/WMA
The disc has unplayable formatted data.
aRefer to the description about MP3/WMA for playable sound data except CD-
DA (i.e. music CD).
No playback or disc
ejected
42
The playability of some CD-R/RWs may depend on the combination of media,
recording software and recorder to be used even if these CD-R/RWs are playable
on other devices such as a PC.
aMake CD-R/RWs in a different combination of media, recording software
and recorder after referring to the description about MP3/WMA.
The CD-R/RWs that are
playable on other
devices are not playable
on this unit.
There is a flaw or foreign objects on the disc.
aRemove the foreign objects, or use a flawless disc. For MP3/WMA, refer to
the description about MP3/WMA.
Sound skipping or noise
Playing VBR (Variable Bit Rate) files may cause sound skipping.
aPlay Non-VBR files.
Note:
¡Refer to “Notes on MP3/WMA” (apage 22)
■
DVD
¡It is not possible to switch if the disc does not have multiple audio
Cannot switch the audio
language/subtitle
languages/subtitle languages/angles recorded on it. (Refer to the guide provid-
ed with your disc.)
¡Some discs permit switching through a menu screen.
¡Sometimes, switching angles is possible only with certain scenes.
language/angle.
The audio/subtitle
language selected in the
DVD settings is not
used.
If audio or subtitles in that language are not recorded on the disc, the audio or
subtitles do not switch to that language. (Some discs permit switching through a
menu screen. Refer to the guide provided with your disc.)
The disc is still unfinalized.
aFinalize the disc.
Refer to “Before Disc Playback” (apage 16) or “Notes on Discs”
(apage 48) for other cases.
A DVD–R or DVD–RW is
not playable.
The disc is in the video recording (VR) format.
aPlay video formatted discs.
Refer to “Before Disc Playback” (apage 16) or “Notes on Discs”
(apage 48) for other cases.
43
CQ-VD7005W
Troubleshooting (continued)
■
Display Settings
AUTO
dimmer is selected.
The brightness of the
screen is not stable.
Select one of the dimmer levels from among 1 to 4 to make the dimmer
a
adjustment become free from light intensity.
43
The picture is dark. The
picture is whitish. Something
is wrong with the picture.
The picture is light in color.
The screen is not adjusted properly.
aMake every adjustment of the screen.
The display does not go
back into the unit.
The monitor stops on the way to the home position.
aPress [OPEN] (CLOSE).
■
Remote Control Unit
The battery is inserted in the wrong direction. A wrong battery is inserted.
aInsert a correct battery in the correct direction.
The battery is weak.
aReplace the battery with new one.
The aiming direction of the remote control unit is wrong.
aAim the remote control unit at the sensor of the unit and press buttons.
No response to pressing
buttons
The sensor is exposed to direct sunlight. (The remote control unit may not be
operable when the sensor is exposed to direct sunlight. In such a case, the sys-
tem is not faulty.)
aBlock off sunlight to the sensor.
REAR is selected for the remote control setting.
FRONT
Select
for the remote control setting.
a
Unable to turn on the
power of the main unit
through the remote
control
OFF is selected for the ACC selection.
Select ON for the ACC selection.
a
a
Press [SRC] (PWR) of the main unit to turn on the power.
44
CQ-VD7005W
■
Sound Settings
No sound from left,
right, front, or rear
speaker.
Cables are not correctly connected.
aConnect the cables correctly.
44
Left and right sounds are
reversed.
The speaker leads are connected in reverse between right and left.
aConnect the speaker wires to the correct one.
No sound on the
speaker.
The speaker setting is NO or NONE .
aSet it correctly.
Playing back a disc having a subwoofer channel
NO
YES
Subwoofer is set to
in the speaker setting.
.
¡
¡
¡
Set subwoofer to
a
No sound from the
subwoofer
ON
Private mode is set to
.
OFF
Set private mode to
.
a
ON
Pro Logic is set to
.
OFF
Set Pro Logic to
a
.
45
CQ-VD7005W
Troubleshooting (continued)
❑ Error Display Messages
■ CD/MP3/WMA/DVD/VCD (Video CD)
45
Display
Possible cause
Possible solution
a
Disc is dirty, or is upside down.
aCheck disc.
NON PLAYABLE DISC
Disc has scratches.
aCheck disc.
No operation by some cause.
aPress [u]. If failure persists, press the reset switch. If normal operation is not
restored, call the store where you purchased the unit or the nearest Panasonic
Service Center.
MECHANISM ERROR
The type of the file that is selected is not supported.
FILE ERROR
PROTECTED
NO DISC
aCheck disc.
A WMA file can be copyrighted.
aThe file protected by copyright is not playable.
No disc is in the player.
aInsert disc into the disc slot.
The region code of the disc to be used is not compatible with this unit.
aPress [u] and check the disc.
REGION ERROR
Note:
¡There may be cases when the disc numbers affected by an error are displayed before “NON PLAYABLE DISC”.
❑ In case you forget the ID code...
In case you forget the ID code, please consult your nearest Panasonic Service Center.
ID code memo
Copy the memo below, fill in the ID code, and keep it in a secure location.
Model No. CQ-VD7005W
ID CODE
46
CQ-VD7005W
❑ Product Servicing
❑ If the Unit Begins to
If the suggestions in the charts do not solve the problem,
we recommend that you take it to your nearest authorized
Panasonic Service Center. The product should be serviced
only by a qualified technician.
Malfunction...
Reset switch
Insert a hard, slender stick into the hole and push the
switch.
46
Important
❑ Replacing the Fuse
Push the switch only when the unit fails to operate with
any buttons. (Stored settings and adjustments are not
cleared.)
If the unit fails to return to normal condition, call the near-
est Panasonic Service Center and ask for repairs.
Use fuses of the same specified rating (15 A). Using dif-
ferent substitutes or fuses with higher rating, or connect-
ing the product directly without a fuse, could cause fire or
damage to this unit.
If the replacement fuse fails, contact your nearest
Panasonic Service Center for service.
TEXT
ENTER
Reset switch
Note:
¡If the ID-CODE has been already set, you will be asked
to enter the ID-CODE right after the unit is restarted.
Maintenance
❑ Caution on Cleaning
❑ Cleaning this Unit
When the unit is dirty, wipe the surface of the display
using the Wiping Cloth (supplied).
AAllccoohhooll
Cleaning without the supplied cloth
1 Moisten the soft cloth in dishwashing
soap diluted with water and wring well.
2 Wipe lightly. Go over the same surface
with a dry cloth.
PPeessttiicciiddee
Wax
Wax
Thinner
Thinner
Note:
Benzine
Benzine
¡Since there is the possibility of water drops getting
inside of the unit, do not directly apply cleanser to the
surface.
¡Do not scratch the screen with your nails or other hard
objects. The resulting scratches or marks will obscure
the images.
Your product is designed and manufactured to ensure a
minimum of maintenance. Use a dry soft cloth for routine
exterior cleaning. Never use benzine, thinner or other sol-
vents.
Caution
¡If water drops or similar wet substances get inside
the monitor, it may cause a malfunction.
47
CQ-VD7005W
Notes on Discs
How to hold the disc
¡Do not touch the underside of the disc.
Disc insert
The surfaces of new discs tend to be slippery. Therefore,
when using such a disc for the first time, it may not load
satisfactorily even when it has been inserted into the
unit. At a time like this, insert the disc into the unit as far
as it will go until it is loaded properly.
¡Do not scratch the disc.
¡Do not bend disc.
¡When not in use, keep disc in the case.
47
Printed side
¡When inserting a disc into or ejecting and removing
it from the unit, insert it straight in or eject and
remove it straight out in parallel with the unit.
Otherwise, the disc may be scratched or marked in
the process.
¡When inserting a disc, do not put one disc on anoth-
er. Failure to observe this may cause the discs to
be jammed.
Do not use discs that fit any of the descriptions given
below. Using these discs may damage the discs or
cause the unit to malfunction.
¡Special discs in a shape which is not round
Do not leave discs in the following places:
¡Direct sunlight
¡Near car heaters
¡Dirty, dusty and damp areas
¡On seats and dashboards
¡Partly or wholly transparent disc
Disc cleaning
Use a dry, soft cloth to wipe from the center outward.
Do not attach any seals or labels to your discs.
Do not write on the disc label in a heavy pen or ballpoint
pen.
Wholly transparent disc*
Partly transparent disc
*Wholly semi-transparent disc may not be played back.
¡Discs with adhered labels, etc. on them
<Correct>
<Wrong>
Disc with adhered stickers Labels created by a printer
or tape
Notes on CD-Rs/RWs,
DVD–Rs/RWs
¡You may have trouble playing back some CD-R/RW,
DVD–Rs/RWs discs recorded on CD/DVD recorders
(CD-R/RW, DVD–Rs/RWs drives), either due to their
recording characteristics or dirt, fingerprints, scratch-
es, etc. on the disc surface.
Protective films or sheets
Disc accessories (stabiliz-
ers, etc.)
¡CD-R/RW, DVD–Rs/RWs discs are less resistant to
high temperatures and high humidity than ordinary
music CDs. Leaving them inside a car for extended
periods may damage and make playback impossible.
¡The unit may not successfully playback a CD-R/RW,
DVD–Rs/RWs that was made by the combination of
writing software, a CD/DVD recorder (CD-R/RW,
DVD–Rs/RWs drive) and a disc if they are incompati-
ble with one another.
¡Damaged or deformed discs
Shoddily made discs
Discs with cracks,
scratches or parts missing
¡This player does not play CD-R/RW, DVD–Rs/RWs
discs if the session is not closed.
¡Be sure to observe the handling instructions of CD-
R/RW, DVD–Rs/RWs discs.
Discs with burrs
Please remove the burrs
before use.
¡This player does not play CD-R/RW discs which con-
tain other than CD-DA or MP3/WMA data.
48
CQ-VD7005W
Language Code List
In “OTHER” cases... (apage 36)
Input the four digit language code pressing the buttons
to
.
Touch
to determine.
48
Note:
Setting is finished and the display returns to the main menu.
¡
For retrying selection during number entry, touch/press
¡
[RETURN]
/
.
DVD language menu (apage 36)
Code Language Name
Code Language Name
Code Language Name
6565 Afar
7289 Armenian
7365 Interlingua
7378 Indonesian
7383 Icelandic
7384 Italian
7387 Hebrew
7465 Japanese
7473 Yiddish
7487 Javanese
7565 Georgian
7575 Kazakh
7576 Greenlandic
7577 Cambodian
7578 Kannada
7579 Korean
7583 Kashmiri
7585 Kurdish
7589 Kirghiz
8277 Rhaeto-Romance
8279 Romanian
8285 Russian
8365 Sanskrit
8368 Sindhi
8372 Serbo-Croatian
8373 Singhalese
8375 Slovak
8376 Slovenian
8377 Samoan
8378 Shona
8379 Somali
8381 Albanian
8382 Serbian
8385 Sundanese
8386 Swedish
8387 Swahili
8465 Tamil
6566 Abkhazian
6570 Afrikaans
6577 Ameharic
6582 Arabic
6583 Assamese
6589 Aymara
6590 Azerbaijani
6665 Bashkir
6669 Byelorussian
6671 Bulgarian
6672 Bihari
6678 Bengali; Bangla
6679 Tibetan
6682 Breton
6765 Catalan
6779 Corsican
6783 Czech
6789 Welsh
7665 Latin
8469 Telugu
8471 Tajik
8472 Thai
8473 Tigrinya
8475 Turkmen
8476 Tagalog
8479 Tonga
8482 Turkish
8484 Tatar
6865 Danish
6869 German
6890 Bhutani
6976 Greek
6978 English
6979 Esperanto
6983 Spanish
6984 Estonian
6985 Basque
7065 Persian
7073 Finnish
7074 Fiji
7678 Lingala
7679 Laothian
7684 Lithuanian
7686 Latvian, Lettish
7771 Malagasy
7773 Maori
7775 Macedonian
7776 Malayalam
7778 Mongolian
7779 Moldavian
7782 Marathi
7783 Malay
8487 Twi
8575 Ukrainian
8582 Urdu
8590 Uzbek
7079 Faroese
7082 French
7089 Frisian
7165 Irish
7168 Scots Gaelic
7176 Galician
7178 Guarani
7185 Gujarati
7265 Hausa
7784 Maltese
7789 Burmese
7865 Nauru
7869 Nepali
7876 Dutch
7879 Norwegian
7982 Oriya
8065 Panjabi
8076 Polish
8673 Vietnamese
8679 Volapük
8779 Wolof
8872 Xhosa
8979 Yoruba
9072 Chinese
9085 Zulu
7273 Hindi
7282 Croatian
7285 Hungarian
8083 Pashto, Pushto
8084 Portuguese
8185 Quechua
49
CQ-VD7005W
Definition of Terms
This fully discrete format divides the music signals
into 5.1 channels: Front Left (L), Front Right (R),
Center (C), Left Surround (LS), Right Surround (RS)
and Subwoofer (SW: 0.1 channel) for recording and
playback. The number of channels that are recorded
depends on the software. (1 to 5.1 channels)
Dolby Digital
Playback control (VCD (Video CD))
If the VCD (Video CD) has “With Playback Control”
or others written on the disc surface or on the jacket,
the scenes or information to be viewed (or listened
to) can be selected interactively with the screen by
looking at the menu shown on the screen.
In these instructions, playback using the menu
screen is referred to as the “menu play” for video
CDs. This player supports Video CDs with playback
control.
49
Manufactured under license from Dolby
Laboratories. “Dolby”, “Pro Logic”, and the
double-D symbol are trademarks of Dolby
Laboratories.
Title, Chapter (DVD)
DVDs are divided into some large sections (titles) or
some small sections (chapters). Each section is
numbered; these numbers are called “Title number”
or “Chapter number”.
Dolby Pro Logic
This format records signals from four channels
[Front Left (L), Front Right (R), Center (C), and
Monaural Surround (S)] in two channels, decodes
those channels through a Dolby Pro Logic decoder,
and then outputs the resulting signals in four chan-
nels.
Title 1
Chapter 2
Title 2
Chapter 1
……
……
Chapter 1
Track (Video CD/CD)
dts
Video CDs or CDs are divided into some sections
(tracks). Each section is numbered; these numbers
are called “Track number”.
This format requires more data than Dolby Digital,
and provides higher quality surround playback.
Similar to Dolby Digital, this fully discrete format
divides the music signals into 5.1 channels: Front
Left (L), Front Right (R), Center (C), Left Surround
(LS), Right Surround (RS) and Subwoofer (SW: 0.1
channel) for recording and playback.
……
Track 3 Track
Track 1
Track 2
“DTS” and “DTS Digital Surround” are registered trade-
marks of Digital Theater Systems, Inc.
Interactive DVD
An interactive DVD is DVD software which includes
multiple angles, multiple plot endings, etc.
“This product incorporates copyright protection tech-
nology that is protected by U.S. patents and other
intellectual property rights. Use of this copyright
protection technology must be authorized by
Macrovision, and is intended for home and other
limited viewing uses only unless otherwise author-
ized by Macrovision. Reverse engineering or disas-
sembly is prohibited.”
Letterbox screen
This refers to a screen on which the playback picture
of wide-screen DVDs or VCD (Video CD)s appears
with black bands running along the top and bottom.
LPCM (Linear PCM audio)
In this format, the audio signal is converted to digital
data and recorded in two channels without compres-
sion. Because the capacity of a DVD disc is large, it
can store more data with better accuracy than a CD.
Pan & Scan screen
This refers to a screen on which the playback picture
of wide-screen DVDs or VCD (Video CD)s is cut off
at the left and right sides.
50
CQ-VD7005W
Specifications
General
Audio section
¡Power supply
: 12 V DC (11 V – 16 V), test
voltage 14.4 V, negative
ground
¡Output voltage/Impedance: 2 Vrms/600 Ω
¡Frequency characteristics
(when “LARGE” is selected)
Front L/R, Center, Rear
50
¡Current consumption : Less than 10 A (during disc
playback)
: 18 W x 4 ch
(surround) L/R
¡Delay time
: 20 Hz – 20 kHz ( 1 dB)
¡Power Output
(1 kHz, 1 %, 4 Ω)
Maximum power output : 50 W x 4 ch
•
Dolby Digital
Center
¡
: 0 – 5 ms
¡Compatible speaker
impedance
¡Video input signal
Rear (surround) L/R : 0 – 15 ms
• Dolby Pro Logic
Rear (surround) L/R : 15 – 30 ms
• Distortion
Front L/R
: 4 Ω
: Composite video signal, 1.0
Vp-p (75 Ω)
¡Audio input sensitivity : 2 Vrms
¡Video output signal : Composite video signal, 1.0
Vp-p (75 Ω)
Pre-Amp output voltage : 2 Vrms
Pre-Amp output impedance: Less than 600 Ω
(1 kHz, 0 dB, PCM input) : 0.01 %
¡Dynamic range
¡S/N ratio
: 96 dB (during CD playback)
: 100 dB (during CD playback)
¡
¡
¡Dimensions (W x H x D) : 178 x 50 x 165 mm
¡Weight
Monitor
: 2.4 kg
¡Storage temperature
range
¡Liquid crystal panel
¡Screen dimensions
(W x H x D)
: –20 °C – +80 °C
: 7-inch wide
FM stereo radio
¡Frequency range
¡Usable sensitivity
¡Stereo separation
¡S/N ratio
: 87.5 MHz – 108 MHz
: 7 dB/µV
: 40 dB (1 kHz)
: 63 dB
: 154 x 87 x 177 mm
: 336 960 pixels (234 vertical
x 480 horizontal x 3)
: Over 99.99%
¡Number of pixels
¡Valid pixel ratio
AM radio
¡Display method
: Transparent color filter for-
mat
: TFT (Thin Film Transistor)
active matrix format
¡Frequency range
¡Usable sensitivity
¡Image rejection ratio
: 531 kHz – 1 602 kHz
: 25 dB/µV
: 50 dB
¡Drive method
Note:
¡Specifications and the design are subject to modification without notice due to improvements in technology.
¡Some figures and illustrations on this manual may be different from your product.
Playable region number
This operating instruction manual is for 4 models CQ-VD7005W2/CQ-VD7005W3/CQ-VD7005W4 and CQ-VD7005W5.
The following table shows the playable region number for each model.
Model
Playable region number
2 (ALL)
CQ-VD7005W2
CQ-VD7005W3
CQ-VD7005W4
CQ-VD7005W5
3 (ALL)
4 (ALL)
5 (ALL)
51
CQ-VD7005W
CQ-VD7005W
Matsushita Electric Industrial Co., Ltd.
YFM284C675CA PTW0107-1027
Printed in China
Installation Instructions
àÌÒÚÛ͈Ëfl ÔÓ ÏÓÌÚ‡ÊÛ
Model:
CQ-VD7005W
TEXT
Safety Information
CAUTION:
• PLEASE FOLLOW THE LAWS AND REGULATIONS
OF YOUR STATE, PROVINCE OR COUNTRY FOR
INSTALLATION OF THE UNIT.
1
• TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK OR PRODUCT DAMAGE, DO NOT EXPOSE
THIS APPLIANCE TO RAIN, SPLASHING, DRIP-
PING OR MOISTURE.
2
CQ-VD7005W
Upgrade Options
2
Main Unit
CQ-VD7005W
Rear Monitor
TV Tuner
(CY-TUP133W/CY-TUN133W, option)
®
iPod
Hands-Free Kit featuring
®
Bluetooth technology
(CY-BT100N, option)
Expansion Module
(CY-EM100N, option)
CD Changer
(CX-DP880, option)
DVD Changer
(CX-DH801W, option)
Contents
Safety Information................................................2
Upgrade Options..................................................3
Installation ............................................................4
Electrical Connections ......................................10
3
CQ-VD7005W
Installation
Preparation
Dashboard Installation
3
Installation Opening
Caution
The unit can be installed in any dashboard having an
opening as shown below. The dashboard should be 4.5
mm – 6 mm thick in order to be able to support the unit.
¡Please follow the laws and regulations of your
province or country for installation of the unit.
¡When bending the mounting tab of the mounting
collar with a screwdriver, be careful not to injure
your hands and fingers.
¡We strongly recommend you to wear gloves for
installation work to protect yourself from injuries.
53 mm
182 mm
¡Before installation, check the radio operation with
antenna and speakers.
¡Disconnect the cable from the negative (–) battery ter-
minal (see caution below).
¡The unit should be installed in a horizontal position
with the front end up at a convenient angle, but not
more than 30°.
Installation Precautions
This product should be installed by a professional
installer, if possible.
In case of difficulty, please consult your nearest author-
ized Panasonic Service Center.
1. This system is to be used only in a 12 V DC battery
system (car) with negative ground.
2. Follow the electrical connections carefully (a page
10-17). Failure to do so may result in damage to the
unit.
0 – 30°
3. Connect the power lead after all other connections are
made.
4. Be sure to connect the battery lead (yellow) to the pos-
itive terminal (+) of the battery or fuse block (BAT) ter-
minal.
5. Insulate all exposed wires to prevent short circuiting.
6. Secure all loose wires after installing the unit.
Caution
¡Do not disconnect the battery terminals of a car with
trip or navigational computer since all user settings
stored in memory will be lost. Instead take extra
care with installing the unit to prevent shorts.
7. Please carefully read the operating and installation
instructions of the respective equipment before con-
necting it to this unit.
4
CQ-VD7005W
❏ Installation Hardware
❏ Installation Hardware
(For Installation)
(For Wiring)
4
No.
Item
Diagram Qty.
No.
Item
Diagram Qty.
1
1
Trim Plate
Power Connector
q
!
<YFC054C087CA>
1
<YAJ024C117ZA>
1
Clip Connector
!
!
1
Mounting Collar
w
e
<YFX214C433CA>
Reverse Extension Cord
2
<YFX054C077CA>
1
Mounting Spring
<YEAJ012897>
Note:
Mounting Bolt (5 mmø)
r
t
y
¡The number in parenthesis underneath each accessory
part name is the part number for maintenance and serv-
ice.
¡Accessories and their parts numbers are subject to
modification without prior notice due to improvements.
¡Use the supplied screws for installation exclusively. In
case of losing any of them, please order the specific
screw.
Tapping Screw
(5 mmø x 16 mm)
1
1
Hex. Nut (5 mmø)
<ZZBISVD7001A>
1
<YFG044C002ZA>
2
Rear Support Strap
u
Round Head Screw
(5 mmø x 6 mm)
Flat-Head Screw
(5 mmø x 6 mm)
Round Head Screw
(4 mmø x 3 mm)
i
o
!
4
4
<ZZBISVD7001B>
2
Spacer
!
!
1
set
Double-Faced Adhesive Tape
<ZZBISVD7001E>
❏ Transportation Bracket Removal
Be sure to remove the transportation brackets before use (installation).
Round Head Screw
(5 mmø x 6 mm)
Use round head screws (5 mmø x 6 mm) for installation. (apage 8)
Be careful not to lose these screws.
Round Head Screw
(5 mmø x 6 mm)
Transportation
Bracket
Transportation
Bracket
5
CQ-VD7005W
Installation (continued)
Mounting the Main Unit
5
❏ Installation Procedures (When using Mounting Collar w)
Note:
Insert the Mounting Collar winto the dashboard, and
¡The car model, installation condi-
bend the mounting tabs out with a screwdriver.
1
tions and combination of the units
used may impose some restric-
Fastening the Mounting Collar
tions on opening and closing the
monitor as well as on the angle
and position to which the monitor
can be adjusted.
How much to bend the tabs will vary depending on the
car. Bend them with a screwdriver to fasten the
Mounting Collar
w
securely in the dashboard.
Dashboard
IMPORTANT
When this unit is installed in dash-
board, ensure that there is sufficient
air flow around the unit to prevent
damage from overheating. Do not
block any ventilation holes on the
unit.
wMounting Collar
Tab
rMounting Bolt
(5 mmø)
Power Connector
!
eMounting Spring
Attach the Mounting Springs eto the unit.
2
oFlat-Head Screw
Establish the rear connection of the unit.
After fixing Power Connector !, fix the rear of the unit to
(5 mmø x 6 mm)
the car body by either method (a) or (b) shown at right.
3
Insert the unit into Mounting Collar w.
Secure the clamp plate of Mounting Collar
wto the hook of Mounting Spring e.
4
Clamp plate
Insert Trim Plate q.
5
6
After installation
reconnect the negative
(–) battery terminal.
6
CQ-VD7005W
Method for Fixing the Mounting Spring
Two holes of the mounting spring allow you to select between two mounting types as shown below.
6
(A) Regular installation method
(B) Deeper installation method
A few millimeters of
console projecting
Less projecting
oFlat-Head Screw
oFlat-Head Screw
oFlat-Head Screw
oFlat-Head Screw
Caution
¡Method (B) is not available in some types of cars.
Method for Fixing the Rear of the Unit
(b) Using the Rubber Cushion (option)
(a) Using the Rear Support Strap u.
Fire wall of car
Rear Support Bracket
(Provided on the Car)
3 mmø
Rear Support Strap
u
Rubber Bushing
(option)
Tapping Screw
(5 mmø x 16 mm)
t
Hex. Nut
(5 mmø)
y
Mounting Bolt
(5 mmø)
r
Mounting Bolt
(5 mmø)
r
7
CQ-VD7005W
Installation (continued)
❏ Installation Procedures (When not using Mounting Collar w)
Use the brackets supplied with your car when mounting this unit. The bracket shape and mounting method vary with car
manufacturers, car types and manufacturing year. Please consult your nearest dealer or installer.
7
Select mounting screws according to the hole positions and hole shape of the bracket.
iRound Head Screw (5 mmø x 6 mm)
2 pieces
Recycle the Round Head Screws that fixed the transportation brackets for two more
positions.
!Round Head Screw (4 mmø x 3 mm)
When using these
mounting holes
4 pieces
oFlat-Head Screw (5 mmø x 6 mm)
4 pieces
iRound Head Screw
Use the supplied Spacer !if mounting hole of your
car is shaped like below.
(5 mmø x 6 mm)
!Spacer
Mounting Hole
of a Bracket
(in section)
Bracket
Existing Bracket (R)
!Double-Faced
Adhesive Tape
iRound Head Screw
!Spacer
(5 mmø x 6 mm)
!Double-Faced Adhesive Tape
Existing Bracket (L) (Bracket originally attached to the car)
To Remove the Unit
q Push the right and left clamp plates outward, one at a time, and pull the unit toward yourself.
w After removing the right and left clamp plates, pull the unit with both hands till it comes out.
w
q
Push here to
remove the
clamp plates.
8
CQ-VD7005W
Connecting the Side Brake (Parking Brake) Connection Lead
8
Caution
¡For safety, be sure to ask your nearest professional installer to do this connection.
Hand brake
Foot brake
Side brake (parking brake) switch
The side brake (parking brake) switch position varies with car model.
For details on the exact location of the side brake (parking brake) switch
in your car, contact your dealer.
Brake light
Battery
+
—
SIDE BRAKE
Side Brake (Parking Brake) Connection
Lead (Bright green)
When the side brake (parking brake) lever is
engaged, the unit is grounded by the chassis.
!Clip Connector
Car chassis
q Attach a Clip Connector !to the end of the side
w The Clip Connector !is connected to the power
source side lead of the side brake (parking brake)
lever.
brake (parking brake) connection lead.
Comes up to this point.
Side Brake (Parking Brake) Connection Lead
(Bright green)
Power source side lead
9
CQ-VD7005W
Electrical Connections
Caution
¡This unit is designed for use in a car having a 12 V negative ground battery system.
¡Be sure to insulate any exposed wires from the car chassis. Bundle all cables and keep cable terminals free from
any metal parts.
¡Note that if your car has a driving computer or a navigation computer, disconnecting the cable from the battery
may clear the memory.
9
¡Run the cords avoiding the spots where the temperature can be extremely high.
Navi Mute Lead (Orange)
Connect to the Navi Mute Lead of the Panasonic car
navigation system. (available in future)
Power Connector
!
NAVI MUTE
ANT-CONT MAX 0.1A
Motor Antenna Relay Control Lead (Blue)
(To motor antenna) (Max. 100 mA)
This lead is not intended for use with a switch actuated
power antenna.
SIDE BRAKE
Side Brake (Parking Brake) Connection Lead (Bright
green)
Be sure to wire the side brake (parking brake) for safety and
preventing accidents. (apage 9)
Front Right + (Gray)
Front Right – (Gray/black stripe)
FRONT SP
AMP-CONT MAX 0.1A
External Amplifier Control Power Lead (Blue/white stripe)
To an external amplifier.
Note:
Front Left + (White)
Front Left – (White/black stripe)
¡Use the power control lead of the TV tuner for TV
tuner connection.
¡Connect both the power control lead of the TV
tuner and the amplifier control connector of the
external amplifier when the TV tuner and external
amplifier are connected at the same time.
Rear Right + (Violet)
Rear Right – (Violet/black stripe)
REAR SP
ACC
Power Lead (Red)
To ACC power, +12 V DC.
(Resistor 1 kΩ)
Rear Left + (Green)
Rear Left – (Green/black stripe)
Speaker connections
Battery Lead (Yellow)
To the car battery, continuous +12 V DC.
BATTERY 15 A
(Fuse 15 A)
(Noise Filter)
• Do not connect more than one speaker to one set of
speaker leads (except for connecting to a tweeter).
Use of speakers which do not match the specifications
can cause burning, smoking or damage of the speakers.
• Do not use a 3-wire type speaker system having a com-
mon earth lead.
Ground Lead (Black)
To a clean, bare metallic part of the car chassis
10
CQ-VD7005W
Note:
¡To prevent from damage to the unit, be sure to follow the wiring diagrams below.
¡Be sure to fully plug in the connectors. Secure them with clamps and tapes.
¡All other installation methods require the use of dedicated metal fittings. Consult with a qualified servicing engineer or
your dealer if other methods are required.
10
: This book refers to connections to the Panasonic car navigation system that will come onto the market in the
future. Descriptions regarding the car navigation system are boxed with a dotted line.
RGB Connector
To the Panasonic Car Navigation System (available in future).
System-up Connector
To external devices equipped with system-up connector.
CQ-VD7005W
(Rear)
Radio Antenna Connector (RADIO ANT IN)
(R)(Red)
Video Output Terminal (AV-OUT)
Connect the rear monitor. (apage 16)
(L)(White)
(Yellow)
AV-OUT
(R)(Red)
Pre-Out Connector (front)
PRE-OUT FRONT
PRE-OUT CENTER
To an external amplifier.
(L)(White)
Pre-Out Connector (center)
To an external amplifier.
(Black)
(R)(Red)
Pre-Out Connector (rear)
PRE-OUT REAR
S.W-OUT
To an external amplifier.
(L)(White)
Pre-Out Subwoofer connector (mono)
To an external amplifier.
(Black)
(R)(Red)
(L)(White)
(Yellow)
Video Input Terminal (AV1-IN/AV2-IN)
Connect a VCR, camcorder, other brand’s car
navigation system, etc. (apage 16)
Note: When an external device is connected
to the system-up connector, the audio termi-
nals, {(R)(Red), (L)(White)}, of AV2-IN are
disabled.
AV1-IN
(R)(Red)
(L)(White)
(Yellow)
AV2-IN
(Yellow)
CAMERA-IN
Camera Input Terminal (CAMERA-IN)
Connect a rear view camera. (apage 15)
REMOTE-IN
Remote-In Lead
(not used)
(Brown/black stripe)
REVERSE
Reverse Lead
When connecting the rear view camera, use
the reverse lead. (apage 15)
(Violet/white stripe)
Note: Use a Reverse Extension Cord
!
if needed.
11
CQ-VD7005W
Electrical Connections (continued)
Connection with DVD Changer (CX-DH801W)
Note:
¡Refer to the operating instructions for the connected devices, in addition.
11
DVD Changer
CX-DH801W (option)
Ground Lead (Black)
To a clean, bare metallic part of the car chassis
Power Connector
(Supplied with CX-DH801W)
BATTERY 5 A
Battery Lead
(Yellow) To the car battery, continuous +12 V DC
Power Lead (Red) (not used)
DIN Cord (Black)
ACC
DIN Connector
(R) (Red)
CHANGER IN
(L) (White)
Conversion Cable for DVD/CD Changer
(CA-CC30N, option)
RCA Cord
System-up
connector
CQ-VD7005W
(Rear)
(not used)
AV2-IN
(Video)
(Yellow)
(Video)
(Yellow)
12
CQ-VD7005W
Connection with CD Changer (CX-DP880)
Note:
¡Refer to the operating instructions for the connected devices, in addition.
12
CD Changer
CX-DP880 (option)
Ground Lead (Black)
To a clean, bare metallic part of the car
chassis
Power Connector
(Supplied with CX-DP880)
Battery Lead (Yellow)
To the car battery, continuous
+12 V DC
DIN Cord (Black)
(R) (Red)
RCA Cord
CHANGER IN
(L) (White)
DIN Connector
Conversion Cable for DVD/CD
Changer (CA-CC30N, option)
System-up
connector
CQ-VD7005W
(Rear)
13
CQ-VD7005W
Electrical Connections (continued)
Connection with Expansion Module (CY-EM100N)
Note:
¡Refer to the operating instructions for the connected devices, in addition.
13
Head unit/Expansion Module
Connecting cable
(Supplied with CY-EM100N)
(Video) (Yellow)
(L) (White)
System-up
Connector
(R)
(Red)
(R) (Red)
(L) (White)
(Video) (Yellow)
VIDEO OUT
AUDIO OUT
Camcorder
(option)
Expansion Module
CY-EM100N (option)
CQ-VD7005W
(Rear)
DVD Changer
(Video)
(Yellow)
CX-DH801W (option)
RCA cord
(option)
VIDEO OUT
iPod
VIDEO-CNT
(Video)
(Yellow)
(L) (White)
Direct Cable for iPod
CHANGER IN
(CA-DC300N, option)
Conversion Cable
(R) (Red)
for DVD/CD
Changer (CA-
CC30N, option)
14
CQ-VD7005W
Connection with Rear View Camera
Note:
¡Refer to the operating instructions for the connected devices, in addition.
14
Rear View Camera
Control Unit (option)
CQ-VD7005W
(Rear)
Camera Input
Rear View Camera
(Video)
(CY-RC50KW) (option)
(Yellow)
RCA Cord (option)
CAMERA-IN
(Video)
Camera Input Terminal
(Yellow)
(Yellow)
Reverse lamp
Clip connector
(option)
Battery
Car chassis
REVERSE
P
Reverse Lead
(Violet/white stripe)
Reverse Extension Cord
(Violet/white stripe)
!
R
N
D
2
Transmission gear
L
Connecting the Reverse Lead
If using an optional rear view camera, the reverse lead
must be connected.
Connect the reverse lead (violet/white stripe) to the posi-
tive (+) lead of the reverse lamp (the lamp with a clear
lens that lights when the transmission gear is shifted into
the reverse position).
Note:
Check the reverse lamp.
¡Connect the reverse lead after cutting the terminal at
the end.
¡Use a Reverse Extension Cord !if needed.
Take it out of the back of
the tail lamp mount.
15
CQ-VD7005W
Electrical Connections (continued)
Connection with Rear Monitor
Note:
¡Refer to the operating instructions for the connected devices, in addition.
¡Please observe what shapes the connectors of the connecting devices are and where each of them is connected to in
order to establish a proper connection.
15
STAND BY (R)
COLOR LCD MONITOR
ON (G)
Rear Monitor
Caution
¡For people sitting in the front seats, please
enjoy only audio during driving.
Panasonic VM1500
Audio Right
Audio Left
Video Input
Example:
(Video) (Yellow)
(R) (Red)
CQ-VD7005W
(Rear)
(L) (White)
(Video) (Yellow)
AV-OUT
RCA Cord
(option)
(R) (Red)
(L) (White)
Connection with VCR or Camcorder
Note:
¡Refer to the operating instructions for the connected devices, in addition.
¡Please observe what shapes the connectors of the connecting devices are and where each of them is connected to in
order to establish a proper connection.
CQ-VD7005W
(Rear)
(Video) (Yellow)
(R) (Red)
RCA Cord
(option)
AV1-IN
(L)
(White)
(L) (White)
(R)
(Red)
(Video)
(Yellow)
INTELLIGENT SYSTEM
POWER
BS G-CODE
Example:
Video Output
Audio Left
Audio Right
VCR (option)
Camcorder (option)
16
CQ-VD7005W
Connection with TV Tuner
Note:
¡Refer to the operating instructions for the connected devices, in addition.
16
External Amplifier Control Power Lead
Note:
¡Connect both the power control lead of the TV tuner and the amplifier control
connector of the external amplifier when the TV tuner and external amplifier are
connected at the same time.
Clip connector
(option)
Power Control Lead
PWR-CONT
AMP-CONT MAX 0.1 A
Power
!
Connector
System-up Connector
(supplied with CY-TUP133W/
CY-TUN133W)
Power Connector
(supplied with CY-TUP133W/
CY-TUN133W)
CQ-VD7005W
(Rear)
(not used)
(Video)
(Yellow)
(Video)
(Yellow)
TV Tuner
CY-TUP133W/
CY-TUN133W (option)
RCA Cord
(supplied with CY-TUP133W/
CY-TUN133W)
17
CQ-VD7005W
Matsushita Electric Industrial Co., Ltd.
YFM294C099CA PTW0107-1027
Printed in China
System Upgrade Guidebook
àÌÒÚÛ͈Ëfl ÔÓ ‡Ò¯ËÂÌ˲ ÒËÒÚÂÏ˚
Model:
CQ-VD7005W
Safety Information
■
■
Read the operating instructions for the unit and all other
components of your car audio system carefully before using
the system. They contain instructions about how to use the
system in a safe and effective manner. Panasonic assumes
no responsibility for any problems resulting from failure to
observe the instructions given in this manual.
This manual uses pictographs to show you how to use the
product safely and to alert you to potential dangers resulting
from improper connections and operations. The meanings of
the pictographs are explained below. It is important that you
fully understand the meanings of the pictographs in order to
use this manual and the system properly.
1
This pictograph intends to alert you to the pres-
ence of important operating instructions and
installation instructions. Failure to heed the
instructions may result in severe injury or
death.
This pictograph intends to alert you to the pres-
ence of important operating instructions and
installation instructions. Failure to heed the
instructions may result in injury or material dam-
age.
Warning
Caution
Observe the following warnings when
installing.
Warning
Observe the following warnings when using
this unit.
The driver should neither watch the display nor
operate the system while driving.
Watching the display or operating the system will distract
the driver from looking ahead of the vehicle and can cause
accidents. Always stop the vehicle in a safe location and
use the parking brake before watching the display or oper-
ating the system.
❑
Disconnect the lead from the negative (–) battery
terminal before installation.
Wiring and installation with the negative (–) battery termi-
nal connected may cause electrical shock and injury due to
a short circuit.
❑
Some cars equipped with the electrical safety system have
specific procedures of battery terminal disconnection.
FAILURE TO FOLLOW THE PROCEDURE MAY LEAD TO
THE UNINTENDED ACTIVATION OF THE ELECTRICAL
SAFETY SYSTEM RESULTING IN DAMAGE TO THE VEHI-
CLE AND PERSONAL INJURY OR DEATH.
❑
❑
Use the proper power supply.
This product is designed for operation with a negative
grounded 12 V DC battery system. Never operate this
product with other battery systems, especially a 24 V DC
battery system.
❑
Never use safety-related components for installa-
tion, grounding, and other such functions.
Do not use safety-related vehicle components (fuel tank,
brake, suspension, steering wheel, pedals, airbag, etc.) for
wiring or fixing the product or its accessories.
Keep batteries and insulation film out of reach of
infants.
Batteries and insulation film can be ingested, so keep them
out of the reach of infants. If an infant ingests a battery or
insulation film, please seek immediate medical attention.
Protect the Deck Mechanism.
Do not insert any foreign objects into the slot of this unit.
Do not disassemble or modify the unit.
Do not disassemble, modify the unit or attempt to repair
the product yourself. If the product needs to be repaired,
consult your dealer or an authorized Panasonic Service
Center.
Do not use the unit when it is out of order.
If the unit is out of order (no power, no sound) or in an
abnormal state (has foreign objects in it, is exposed to
water, is smoking, or smells), turn it off immediately and
consult your dealer.
The remote control unit should not lie about in the
car.
If the remote control unit lies about, it could fall on the
floor while driving, get wedged under the brake pedal, and
lead to a traffic accident.
❑
❑
Installing the product on the air bag cover or in a
location where it interferes with airbag operation
is prohibited.
Check for piping, gasoline tank, electric wiring,
and other items before installing the product.
If you need to open a hole in the vehicle chassis to attach
or wire the product, first check where the wire harness,
gasoline tank, and electric wiring are located. Then open
the hole from outside if possible.
❑
❑
❑
❑
❑
Never install the product in a location where it inter-
feres with your field of vision.
❑
❑
❑
Never have the power cord branched to supply
other equipment with power.
After installation and wiring, you should check the
normal operation of other electrical equipment.
The continuation of their using in abnormal conditions may
cause fire, electrical shock or a traffic accident.
❑
In the case of installation to an airbag equipped
car, confirm warnings and cautions of the vehicle
manufacturer before installation.
Refer fuse replacement to qualified service per-
sonnel.
When the fuse blows out, eliminate the cause and have it
replaced with the fuse prescribed for this unit by a qualified
service engineer. Incorrect replacement of the fuse may
lead to smoke, fire, and damage to the product.
❑
❑
Make sure the leads do not interfere with driving
or getting in and out of the vehicle.
Insulate all exposed wires to prevent short circuit-
ing.
2
CQ-VD7005W
❑
Use the designated parts and tools for installation.
Use the supplied or designated parts and appropriate tools
to install the product. The use of parts other than those
supplied or designated may result in internal damage to the
unit. Faulty installation may lead to an accident, a malfunc-
tion or fire.
Do not block the air vent or the cooling plate of the
unit.
Blocking these parts will cause the interior of the unit to
overheat and will result in fire or other damage.
Do not install the product where it is exposed to
strong vibrations or is unstable.
Avoid slanted or strongly curved surfaces for installation. If
the installation is not stable, the unit may fall down while
driving and this can lead to an accident or injury.
Caution
Observe the following cautions when using
this unit.
Keep the sound volume at an appropriate level.
Keep the volume level low enough to be aware of road and
traffic conditions while driving.
Do not insert or allow your hand or fingers to be
caught in the unit.
To prevent injury, do not get your hand or fingers caught in
moving parts or in the disc slot. Especially watch out for
infants.
This unit is designed for use exclusively in auto-
mobiles.
Do not operate the unit for a prolonged period with
the engine turned off.
Operating the audio system for a long period of time with
the engine turned off will drain the battery.
2
❑
❑
❑
❑
❑
❑
❑
Installation Angle
The product should be installed in a horizontal position
with the front end up at a convenient angle, but not more
than 30˚.
The user should bear in mind that in some areas there may
be restrictions on how and where this unit must be
installed. Consult your dealer for further details.
Wear gloves for safety. Make sure that wiring is
completed before installation.
To prevent damage to the unit, do not connect the
power connector until the whole wiring is complet-
ed.
Do not connect more than one speaker to one set
of speaker leads. (except for connecting to a
tweeter)
❑
❑
Do not expose the unit to direct sunlight or exces-
sive heat.
Otherwise these will raise the interior temperature of the
unit, and it may lead to smoke, fire, or other damage to the
unit.
❑
❑
Do not use the product where it will be exposed to
water, moisture, or dust.
Exposure of the unit to water, moisture, or dust may lead
to smoke, fire, or other damage to the unit. Make especially
sure that the unit does not get wet in car washes or on
rainy days.
❑
Observe the following cautions when
installing.
Observe the following cautions when handling
the battery for the remote control unit.
❑
Refer wiring and installation to qualified service
personnel.
●
●
Use only specified battery (CR2025).
Match the polarity of the battery with the (+) and (–) marks
in the battery case.
Replace a dead battery as soon as possible.
Remove the battery from the remote control unit when not
using it for an extended period of time.
Insulate the battery (by placing them in a plastic bag or
covering them with vinyl tape) before disposal or storage.
Dispose of the battery according to the local regulations.
Do not disassemble, recharge, heat or short the battery. Do
not throw a battery into a fire or water.
Installation of this unit requires special skills and experi-
ence. For maximum safety, have it installed by your dealer.
Panasonic is not liable for any problems resulting from
your own installation of the unit.
●
●
●
❑
❑
Follow the instructions to install and wire the prod-
uct.
●
●
Not following the instructions to properly install and wire
the product could cause an accident or fire.
Take care not to damage the leads.
In case of battery leakage
When wiring, take care not to damage the leads. Prevent
them from getting caught in the vehicle chassis, screws,
and moving parts such as seat rails. Do not scratch, pull,
bend or twist the leads. Do not run them near heat sources
or place heavy objects on them. If leads must be run over
sharp metal edges, protect the leads by winding them with
vinyl tape or similar protection.
●
●
●
Thoroughly wipe the battery liquid off the battery case and
insert new battery.
If any part of your body or clothing comes into contact
with battery liquid, wash it with plenty of water.
If battery liquid comes into contact with your eyes, wash
them with plenty of water and get immediate medical atten-
tion.
CAUTION:
• PLEASE FOLLOW THE LAWS AND REGULATIONS OF YOUR STATE, PROVINCE OR COUNTRY FOR WIRING,
INSTALLATION, AND USE OF THIS UNIT AND THE DEVICES TO BE CONNECTED.
3
CQ-VD7005W
Before Reading These Instructions
Panasonic welcomes you to our constantly growing family of electronic products owners.
We endeavor to give you the advantages of precise electronic and mechanical engineering, manufactured with carefully
selected components, and assembled by people who are proud of the reputation their work has built for our company.
We know this product will bring you many hours of enjoyment, and after you discover the quality, value and reliability
we have built into it, you too will be proud to be a member of our family.
3
This is a guide book specific to system upgrading. Please refer to the operating instructions for basic operations,
menu operations, specifications, etc.
System upgrade sample
TV Tuner
(CY-TUP133W/CY-TUN133W,
option)
Main Unit
CQ-VD7005W
Rear Monitor
®
iPod
Hands-Free Kit featuring
®
Bluetooth technology
(CY-BT100N, option)
Expansion Module
(CY-EM100N, option)
CD Changer
(CX-DP880, option)
DVD Changer
(CX-DH801W, option)
4
CQ-VD7005W
Connectable devices
■ DVD Changer
■ Hands-Free Phone System
4
The optional adapter (Conversion Cable for DVD/CD
Changer: CA-CC30N) allows you to connect the optional
Panasonic DVD changer unit (CX-DH801W). For details, refer
to the operating instructions for the DVD changer unit.
You can connect the optional Hands-Free Phone System
(Hands-Free Kit featuring Bluetooth technology:
CY-BT100N). For details, refer to the operating instructions for
the Hands-Free Phone System.
®
Note: This unit is designed only for receiving calls. It
■ CD Changer
cannot send calls.
The optional adapter (Conversion Cable for DVD/CD
Changer: CA-CC30N) allows you to connect the optional
Panasonic CD changer unit (CX-DP880). For details, refer to
the operating instructions for the CD changer unit.
®
Bluetooth
The Bluetooth word mark and logo are owned by the
Bluetooth SIG, Inc. and any use of such marks by
Matsushita Electric Industrial Co.,Ltd. is under license.
Other trademarks and trade name are those of their
respective owners.
■ TV tuner
You can connect the optional Panasonic TV tuner unit (CY-
TUP133W/CY-TUN133W). For details, refer to the operating
instructions for the TV tuner unit.
■ Expansion Module (hub unit)
You can connect the optional Expansion Module (hub unit)
(CY-EM100N). Connection of the Expansion Module allows
you to simultaneously connect optional devices mentioned
before as well as other AV devices. For details, refer to the
operating instructions for the Expansion Module.
Note:
¡CY-TUP133W/CY-TUN133W is an analog TV-specific tuner.
¡If the analog broadcast system is replaced with the digital
broadcast system in a country or area where CY-
TUP133W/CY-TUN133W is used, TV broadcasts cannot be
received.
Connectable devices
¡CD/DVD changer (max. 1)
¡iPod (max. 2)
¡iPod with Video (max. 1)
¡Hands-Free Phone System (max. 1)
¡TV tuner (max. 1)
¡Inquire about the termination of analog broadcasting to the
authorities concerned in the country or area where CY-
TUP133W/CY-TUN133W is used.
®
■ iPod
The optional adapter (Direct Cable for iPod: CA-DC300N) allows
you to connect the optional iPod series.
Note:
The iPod equipped with a dock connector is exclusively con-
nectable. Further information about the controllable iPod is
described below.
¡Market conditions regarding optional devices vary with
countries and regions. For further information, consult your
dealer.
¡If a non-Panasonic product is connected to this unit, we do
not guarantee the operations of the product.
¡If iPod with Video is connected, no more iPod can be con-
nected.
Controllable iPod/software version
¡ 3rd generation iPod/ver. 2.3
¡ 4th generation iPod/ver. 3.1.1
¡ 5th generation iPod/ver. 1.2 (Refer to “Precautions in
using an iPod with Video”)
¡ iPod photo/ver. 1.2.1
¡ iPod mini/ver. 1.4.1
¡ iPod nano/ver. 1.2
* Operation check has been completed with software avail-
able at the end of September, 2006. We do not guarantee
the operation with our future products or upgraded soft-
ware.
iPod is a trademark of Apple Inc., registered in the U.S.A. and
other countries.
5
CQ-VD7005W
Before Reading These Instructions (continued)
System upgrade sample
■ Simultaneous Multi-Device Connection
5
CQ-VD7005W
CD Changer
(CX-DP880, option)
DVD Changer
(CX-DH801W, option)
System-up Connector
Only 1 unit
Conversion Cable for DVD/CD Changer
(CA-CC30N, option)
iPod
Up to 4 units
Direct cable for iPod
(CA-DC300N, option)
Expansion Module
(CY-EM100N, option)
Cellular Phone
Note:
CY-BT100U
¡Refer to individual instruction and instal-
lation manuals for each device for
detailed installation and wiring.
Hands-Free Kit featuring
Bluetooth technology
®
(CY-BT100N, option)
TV Tuner
(CY-TUP133W/CY-TUN133W,
option)
6
CQ-VD7005W
■ 5.1-channel Surround System
This unit has a built-in 4-channel amplifier. The procedure for setting up a 5.1-channel surround system in order to play
DVD software in a way that creates a “you are there” feel in a car is described below.
6
Note:
¡Even if you are using this unit without installing a center speaker, surround speakers, or a subwoofer, it is still neces-
sary to make the speaker settings in order to adjust the sound balance.
Center Speaker:
EAB-CF2
Panasonic
Power amplifier
CQ-VD7005W
Front Speakers:
CJ-DA1733
Surround Speakers:
CJ-DA6923
Subwoofer:
CJ-SW3003
Power amplifier
Contents
Common
Settings
Safety Information................................................2
Before Reading These Instructions....................4
Touch Panel Operation Overview.......................8
Settings...............................................................20
As needed
Troubleshooting.................................................22
Each Source
TV Tuner Control................................................10
CD Changer Control...........................................12
DVD Changer Control ........................................13
Bluetooth Hands-Free Kit .................................16
iPod Control........................................................18
7
CQ-VD7005W
Touch Panel Operation Overview
❒ Notes on the Touch Panel
Before operation
¡Clean the surface of the touch panel. (aOperating
Instructions)
Operation
¡Use only your fingers to operate the touch panel.
¡Do not press the panel forcefully.
¡Do not scratch the panel with fingernails or any
hard objects.
¡Do not use a pen or other sharp implements to
operate the touch panel.
¡Do not bump the front panel.
aFailure to observe the above may damage or
break the glass on the surface of the touch
panel.
7
The State of Operation Screen
Example: CD Changer
Note
:
¡The following picture is partly darkened for explanation.
¡Displaying contents and their positions partly vary with each mode. Refer to the description of each mode for details.
Display Button
(anext page)
Source Button
(Content varies with each
source)
Menu Button
Displays the Source Selection Screen.
Displays the Menu Screen.
Source Selection Screen
Menu Screen
Source Selection Screen appears.
Touch desired source button.
Menu Screen appears. Select desired setting.
Menu Setting, (aOperating Instructions)
Touch
to quit.
Press [MENU] to let Menu
Screen appear.
Press [SRC] to change to
desired mode.
Note:
When an
¡
¡
When
,
,
or
is connected to
is selected on the condition that the
this unit without involving the Expansion Module (CY-
EM100N, option), any of them appears at the AV2
position.
Expansion Module is connected to this unit, the video and
audio of the source connected to AUDIO IN/VIDEO IN of
the Expansion Module come out.
8
CQ-VD7005W
Switching the Display
Touching
allows users to switch between screens as follows.
8
❏ How to Call up Operation Screen
Source
Standard Screen
Operation Screen
CD Changer
(apage 12)
iPod
(apage 18)
❏ How to Cancel OSD (On Screen Display)
Source
Standard Screen
OSD OFF *2
TV tuner (*1)
(apage 10)
DVD Changer (*1)
(apage 13)
*1 To switch Operation Screen ON, touch the center of touch panel or press [ENTER].
*2 The operation screen is not available in the video mode.
Note:
¡Refer to the description of each mode for how to operate the operation screen.
9
CQ-VD7005W
TV Tuner Control
Preparation:
¡Connect a TV tuner (CY-TUP133W/CY-TUN133W,
option) to the unit.
¡For receiving TV broadcasts, stop your car where
there is no obstacle to broadcast reception around.
¡It is required to install the TV antenna to receive TV
broadcasts.
9
TV Mode Selection
Source Button
“
”
Touch Source Button .
q
TILT
CLOSE
d
Touch
(TV)
w
on the Source
Selection Screen.
(Content varies with
connected devices)
Channel selection/
Channel seeking
TV menu
Preset channel
selection
CQ-VD7005W
TEXT
Press [SRC] to change to the TV mode.
Band selection
VOL
ENTER
PWR
MUTE
SRC
MENU
NAVI
To switch Operation Screen ON, touch the center of
touch panel or press [ENTER].
[SRC]
[ENTER]
[]] [[ ]
[}] [{]
Note:
For the operations of the TV tuner with its remote con-
trol, aim the remote control at the remote control sen-
sor of this unit.
¡
The remote control of the TV tuner (CY-TUP133W/CY-
TUN133W, option) cannot turn on or off the power of
the TV tuner.
¡
Tuning
Operations
Band Selection
[BAND]
[ENTER]
TV 1
TV 2
[ ]
[
[ ]
]
[ ]
[
[ ]
]
Up
Channel
Selection
Down
Channel Seeking
[ ]
[
[ ]
]
[ ]
[
[ ]
]
Up
Down
Displaying TV
Menu
Calls up the menu of the tuner.
To cancel, touch again.
–
–
Selecting an Item
on the TV Menu
[
] [
]
[
] [
]
}
{
}
{
Up/down
Left/right
[
] [
]
[
] [
]
]
[
]
[
……
Touch/Press and hold
10
CQ-VD7005W
Preset Memory
Operations
10
12 channels with first to 12th highest in signal strength will be preset to each band.
[BAND] [ENTER]
Auto Preset
Memory
Select a band.
¡Touch/press and hold for more than 2 seconds.
¡“–” appears if the number of receivable channels is less than 12.
New channels overwrite existing saved channels.
Select a band and a channel.
Writing Preset
Memory
[
]
[
]
}
}
d
d
d
Favorite preset channels
can be written after you
have set the preset chan-
nel once.
¡Preset channel writing mode
display appears.
[
] [
]
[
] [
]
]
[
]
[
Select a channel that you want to exchange.
d
d
d
[BAND]
[ENTER]
Determine.
–
–
¡Exit from the preset writing.
Preset Channel
Calling
Down
Up
[
[
]
]
[
[
]
]
}
}
{
{
Select a band and a channel.
Deleting Preset
Memory
[
]
[
]
{
{
Favorite preset channels
can be deleted after you
have set the preset chan-
nel once.
d
d
d
¡Preset channel deleting mode
display appears.
Select a preset number that you want to
delete.
[
}
] [
]
[
}
] [
]
{
{
d
d
d
[BAND]
[ENTER]
Determine.
–
–
¡Exit from the preset channel deletion.
……
Touch/Press and hold for more than 2 seconds
11
CQ-VD7005W
CD Changer Control
Preparation:
¡CD changer functions are designed for optional
¡Connect the CD changer, and load a magazine (discs).
Panasonic CD changer unit. (CX-DP880)
Source Button
CD Changer Mode Selection
11
Current track
“
”
Touch Source Button .
q
TILT
CLOSE
d
Disc number
Touch
on the Source
Selection Screen.
(CH-C)
w
Total track
number
(Content varies with con-
nected devices)
Total time
Random Play
Scan Play
Repeat Play
CQ-VD7005W
TEXT
Press [SRC] to change to the CD
Changer mode.
VOL
ENTER
PWR
SSRRCC
MUTE
MENU
NAVI
To switch Operation Screen ON, touch
.
[SRC]
Disc selection Track selection
[]] [[ ]
[}] [{]
Basic Operations
Operations
Disc Selection
Next disc
[}]
[}]
Previous disc
[{]
[{]
Next track
Beginning of the current track
Previous track (Touch/press twice.)
Track Selection
[d]
[[]
[s]
[]]
Fast forward
Fast Forward/
Fast Reverse
[d]
[[]
Release to resume playback.
Fast reverse
Release to resume playback.
[s]
[]]
Repeat Play
–
–
–
–
To cancel, touch again.
Repeat Play within the
current Disc
To cancel, touch and hold for more than 2 sec-
onds again.
*
*
–
Scan Play
–
–
To cancel, touch again.
The first 10 seconds of the all the discs is played.
To cancel, touch and hold for more than 2 sec-
onds again.
Disc Scan Play
–
Random Play
To cancel, touch again.
–
–
–
–
To cancel, touch and hold for more than 2 sec-
onds again.
Random Play within the
Current Disc
*
……
* Touch panel symbols will change to indicate these current mode.
{D= DISC (disc)}
Touch/Press and hold
,
,
12
CQ-VD7005W
DVD Changer Control
Preparation:
¡DVD changer functions are designed for optional
¡Connect the DVD changer, and load a magazine (discs).
Panasonic DVD changer unit. (CX-DH801W)
DVD Changer Mode Selection
12
“
”
Touch Source Button .
q
d
Source Button
Touch
(CH-
w
TILT
CLOSE
C) on the Source
Selection Screen.
(Content varies with
connected devices)
Operation
Buttons
Press [SRC] to change to the DVD
Changer mode.
Disc/folder
selection
CQ-VD7005W
TEXT
VOL
To switch Operation Screen ON, touch the center of
ENTER
touch panel or press [ENTER].
PWR
SRRC
MUTE
MENU
NAVI
Note:
[SRC]
[ENTER]
[]] [[ ]
[}] [{]
Be sure to connect RCA cord (video)(yellow) of the
¡
Panasonic DVD Changer to AV2-IN and set
CH VIDEO INPUT to ON
(
a
page 20). Otherwise the
changer cannot be controlled through this unit.
Refer to the operating instructions and installation
instructions of CX-DH801W as well.
¡
Basic Operations
Operations
Compatible
Discs
Operations
Track/file Selection
–
–
Next track/file
[d]
DVD VCD
CD MP3
Beginning of the current track/file
Previous track/file (Touch/press twice.)
[s]
Note:
DVD
¡When playing a DVD, there are cases where it is not possible to return to
the start of a chapter that spans 2 titles. (aOperating Instructions)
Fast forward
Fast Forward/
Fast Reverse
–
–
[d]
Release to resume playback.
DVD VCD
CD MP3
Fast reverse
Release to resume playback.
[s]
The speed changes if the button is held down as follows.
Regular speed / 2 times / 5 times / 10 times / 30 times
Next folder
–
–
–
–
Folder Selection
MP3
Previous folder
DVD VCD
CD MP3
To resume playback, touch/press
Stop
[3]
–
–
/ [5].
Pause
DVD VCD
CD MP3
To resume playback, touch/press
[y]
/ [5].
……
Touch/Press and hold
13
CQ-VD7005W
DVD Changer Control (continued)
Basic Operations (continued)
Slow Playback
¡Touch/press and hold in the pause
mode.
DVD VCD
–
[d]
Playback is at about 1/4 normal speed.
To resume normal playback, touch/press
/ [5].
13
Note:
¡Reverse slow playback is not possible.
–
–
–
–
Next disc
DVD VCD
CD MP3
Disc Selection
Previous disc
……
Touch/Press and hold
Chapter/title/track Selection
Showing menu and
selecting an item
q Menu appears.
d
[DVD MENU]
–
d
[]] [[] []] [[]
w Select the desired item.
DVD
Note on VCD:
*
[}] [{] [}] [{]
–
*
VCD
For VCD, press
[RETURN]
d
d
d
instead of
e Determine the setting.
[ENTER] [ENTER]
[RETURN]
[DVD MENU]
.
Returns to the previous display.
–
14
CQ-VD7005W
14
15
CQ-VD7005W
Bluetooth Hands-Free Kit
Connection of the optional Bluetooth hands-free kit
allows users to talk on a handsfree cellular phone in a
car.
Preparation:
¡Connect the Bluetooth hands-free kit (CY-BT100N)
and establish the pairing. Refer to the instruction
manual for the Bluetooth hands-free kit for further
information.
Note:
¡CY-BT100N is designed only for receiving calls. It
cannot send calls.
15
Bluetooth Hands-Free Mode
TILT
CLOSE
This mode is not selectable by pressing [SRC] or touch-
ing an item on the panel, but activated by receiving an
incoming call. (To pick up the phone, press [Hang-on]
on the hands-free kit.)
Note:
¡The telephone number of the calling party is dis-
played.
¡“CONNECT” is displayed when information of the call-
ing party cannot be acquired.
CQ-VD7005W
TEXT
VOL
¡We shall not guarantee all the functions of the
Bluetooth-ready mobile phone to be connected.
ENTER
PWR
SRC
MUTE
MENU
NAVI
[VOL]
Switch unit
[]] [[ ]
Status indicator (Blue LED)
Lights: Call waiting/Talking
Stays out: Not connected
Blinks rapidly: Receiving a call
Blinks slowly:
Pairing/Reconnecting
[Hang-on]/Blue LED
[Hang-up]/Red LED
When receiving a call...
Example: DVD mode
16
CQ-VD7005W
Useful Function
Operations
16
Adjust the volume when a call is coming in.
Adjustment of Ring
Volume
–
down
[–]
When the ringtone is the
same as that of the cellu-
lar phone,
[VOL]
[+]
–
up
[VOL]
When the ringtone is not
the same as that of the
cellular phone (but this
unit-specific sound),
Adjust the volume when a call is coming in.
[+]
or
on
[VOL]
or []]
[
]
]
[–]
or
mute
[VOL]
or [[]
[
]
[
and
appear only when the ringtone is not the same as that of the cellular
¡
phone. The buttons disappear when communication starts.
Adjustment of
phone receiver
volume
–
–
down
[–]
[VOL]
[+]
up
[VOL]
¡Press [Hang-up] on the hands-free kit.
Back to Previous
Source
–
–
–
¡When [Hang-up] on the hands-free kit is pressed to hang up the phone, the previ-
ous mode resumes.
Note:
Source change and AUDIO -related operations in the
¡
¡
Reception of a call during the camera or navigation
system is activated does not call up the Hands Free
screen but displays only the telephone number of the
¡
menu are not feasible during reception of a call. But
volume is adjustable and the power can be turned off
even during reception of a call.
Reception of a call at power-off does not turn on the
power of this unit.
[Hang-on]
calling party. Pressing
phone number from the screen.
deletes the tele-
does not
appear.
Reception of a call at MUTE-on temporarily cancels
the mute function and disables operations. After end
of phone communication, the mute function resumes.
¡
17
CQ-VD7005W
iPod Control
Preparation:
¡Connect the iPod through connecting cable (CA-DC300N, option).
iPod Mode Selection
17
Source Button
Information of current track/file
“
”
Touch Source Button .
q
TILT
CLOSE
d
Touch
w
(iPod) on the
Source Selection
Screen.
text/title scroll
(Content varies with
connected devices)
operation buttons
CQ-VD7005W
TEXT
VOL
Press [SRC] to change to the iPod
mode.
ENTER
PWR
SRC
MUTE
MENU
NAVI
[SRC]
To switch Operation Screen ON, touch
.
[]] [[ ]
[}] [{]
Note:
¡ Disconnect the iPod from this unit, reset the iPod, and connect
the iPod again when a problem occurs including the following:
the iPod is not recognized/the iPod is not operable from the
iPod itself or this unit/the image or sound from the iPod con-
nected to this unit is not correctly reproduced.
¡ “NO iPod” appears until the iPod is recognized after connect-
ing the iPod, turning on the power of the main unit, or per-
forming source selection on the main unit side. This indicates
there is nothing wrong with the main unit.
Controllable iPod/software version
¡ 3rd generation iPod/ver. 2.3
¡ 4th generation iPod/ver. 3.1.1
¡ 5th generation iPod/ver. 1.2 (Refer to “Precautions in
using an iPod with Video”)
¡ iPod photo/ver. 1.2.1
¡ iPod mini/ver. 1.4.1
¡ iPod nano/ver. 1.2
* Operation check has been completed with software available
at the end of September, 2006. We do not guarantee the
operation with our future products or upgraded software.
¡ We shall not guarantee all the functions of the iPod to be con-
nected.
¡ The iPod equipped with a dock connector is exclusively con-
nectable.
¡ The number of displayable characters for a file name is limited.
(up to 252 bytes)
Basic Operations
Operations
Next track/file
[d]
[[]
Track/file Selection
Beginning of the current track/file
Previous track/file (Touch/press twice.)
[s]
[]]
Fast forward
Fast Forward/
Fast Reverse
[d]
[[]
[]]
Release to resume playback.
Fast reverse
Release to resume playback.
[s]
Title Scroll
Scrolls the title once
–
–
To resume playback, touch/press
Pause
–
[y]
again or touch/press
/ [5].
……
Touch/Press and hold
18
CQ-VD7005W
Useful Function
Shuffle Songs
*
*
To cancel, touch again.
–
–
–
–
Shuffle Albums
To cancel, touch and hold again.
18
Note:
The shuffle function of iPod corresponds to the RANDOM function of this unit.
¡
Repeat Play
To cancel, touch again.
–
–
Note:
The All Repeat Play function of iPod is always activated and cannot be canceled
¡
from this unit.
* Touch panel symbols will change to indicate these current mode.
……
Touch/Press and hold
{A= ALBUM (album)},
{S= SONG (song)}
Touching
allows users to switch between screens as follows.
Standard Screen
File indicator
A number up to 999 is displayable.
Current state
File up/down
Operation Screen
File indicator
A number up to 999 is displayable.
Title scroll
Play/pause
Play setting
File up/down
Folder List/File List Screen
Back to 1-upper directory
Playback category selection button
Playback by playlist (default)
Playback by album
Playback by song
Playback by artist
Folder list/file list
19
CQ-VD7005W
Settings
This is a guide book specific to system upgrading. Please refer to the operating instructions for basic operations,
menu operations, specifications, etc.
INPUT/OUTPUT
INPUT SELECT
USER
SCREEN AUDIO DVD
RADIO
19
Input selection
(Navigation set up)
(Navigation Input)
NAVI INPUT
NAVI SETUP
Navigation Setting
: connected to the RGB input cord, or a
car navigation system not connected
RGB
(Navigation Speaker)
NAVI SP
: connected to the AV1-IN
AV1
: Front Left/Right speaker
: Front Left only
BOTH
L ch
RGB
default:
: Front Right only
R ch
(Video input for DVD Changer)
CH VIDEO INPUT
BOTH
default:
: connected to AV2-IN
: unconnected
ON
OFF
OFF
default:
(Navigation mute level)
NAVI MUTE
Note:
¡The audio output should be connected to AV2-IN.
Preparation: Connect the navi mute lead.
: unchanged
: –20 dB
OFF
(Rear view camera set up)
CAMERA
LEV 1
LEV 2
LEV 3
Selection of the terminal that connects to the rear view
camera.
: –30 dB
Preparation: Connect the reverse lead. (aInstallation
: no sound
Instructions)
default:
LEV 1
: connected to the CAMERA-IN
: unconnected
ON
Note:
You can set the navigation mute level when
OFF
is
¡
RGB
selected on NAVI INPUT
.
default: OFF
Note:
Make sure to select OFF when no rear view camera is
¡
connected.
(Navigation Volume)
NAVI VOLUME
Volume adjustment of the car navigation system.
The image from the rear view camera may be blurred
¡
in the night or a dark place.
]
[
: down,
: up
Setting range: 0 to 40
default:
20
Connection with Panasonic car navigation system
: This book refers to connections to the Panasonic
car navigation system that will come onto the mar-
ket in the future. Descriptions regarding the car
navigation system are boxed with a dotted line.
Note:
¡If a non-Panasonic navigation system is connected to
this unit, we do not guarantee the operations of the
navigation system.
20
CQ-VD7005W
Note:
OUTPUT SELECT
20
Output Selection
(Rear Monitor Set up)
REAR MONITOR
You can have different picture and sound on the front
and rear monitors at the same time.
Preparation: Connect another optional rear monitor.
(aInstallation Instruction)
The screen above shows the case that no device is
¡
connected to the Expansion Module. In such a case,
the additional buttons are displayed gray and not selec-
table.
❑ When the Expansion Module (CY-EM100N, option) is
disconnected:
Only single source of audio and video can come out
through the Expansion Module (CY-EM100N, option).
Therefore, if the audio and video from the changer are
played on the front monitor, the audio and video from
the TV cannot be played on the rear monitor at the
same time.
¡
Example:
: same as front monitor*
AUTO
DVD
AV1
When a DVD changer and a TV are connected to the
Expansion Module (CY-EM100N, option),
: DVD/VCD/CD/MP3/WMA
: AV1
: AV2
AV2
* iPod with Video is included.
default: AUTO
Note:
is selectable. However, the setting is not
¡
¡
This menu can also be opened by touching/pressing
¡
feasible because the changer is in operation on the
front monitor.
To play the TV on the rear monitor, select
for the front monitor, or select a source other than
the Expansion Module.
[MENU]
.
and holding
Images are not displayed on the rear monitor in the
DVD changer mode even if is selected.
/
¡
AUTO
❑ When the Expansion Module (CY-EM100N, option) is
connected:
(Hands-free Set Up)
H-F SETUP
Hands-free Set Up
(Hands-free speaker)
H-F SP
Preparation: Connect Bluetooth hands-free kit (CY-
BT100N). (aInstallation Instructions)
Connection of the Expansion Module (CY-EM100N,
option) provides two additional source buttons.
Connection of audio-only source to the Expansion
Module (CY-EM100N, option) provides no additional
button.
¡
: Front Left/Right speaker
: Front Left only
BOTH
L ch
¡
: Front Right only
R ch
default: BOTH
21
CQ-VD7005W
Troubleshooting
❑ If You Suspect Something Wrong
Warning
Check and take steps as described below.
¡Do not use the unit in an irregular condi-
tion, for example, without sound, or with
smoke or a foul smell, which can cause
ignition or electric shock. Immediately stop
using the unit and consult your dealer.
¡Never try to repair the unit by yourself
because it is dangerous to do so.
21
If the described suggestions do not solve the problem, it is rec-
ommended to take the unit to your nearest authorized Panasonic
Service Center. The product should be serviced only by qualified
personnel. Please refer checking and repair to professionals.
Panasonic shall not be liable for any accidents arising out of neg-
lect of checking the unit or your own repair after your checking.
Never take measures especially those other than indicated by
italic letters in “Possible Solution” described below because
those are too dangerous for users to handle themselves.
■
Car Navigation, VCR, Camcorder, Rear View Camera, Rear Monitor
Possible cause
Possible solution
Problem
a
The connection of a car navigation system is not correct.
The picture from a car
navigation system is not
displayed.
aConnect it correctly.
Input setting of a car navigation system is not correct.
aCorrect the input setting.
The picture from a VCR or a
camcorder is not displayed.
A VCR or Camcorder is not connected correctly.
aConnect a VCR or Camcorder correctly.
Rear view camera is not connected correctly.
The picture from a rear
view camera is not
displayed.
aConnect a rear view camera correctly.
Input setting of camera is not correct.
aCorrect the input setting.
The picture or the sound
of the rear monitor is not
switchable.
AUTO
is not selected as the rear monitor setting.
AUTO
Select
for the setting.
a
■
iPod Control
The iPod is not
recognized. The iPod is
not operable from the
iPod itself or this unit.
The image or sound
from the iPod connected
to this unit is not
Communication between this unit and the iPod may be temporarily interrupted
even when both of them are active. This phenomenon does not indicate that this
unit is out of order.
aDisconnect the iPod and reset the iPod. After completion of iPod reset, con-
nect the iPod again.
correctly reproduced.
22
CQ-VD7005W
❑ Error Display Messages
■ CD Changer/DVD Changer Control
Display
Possible cause
Possible solution
a
22
Disc is dirty, or is upside down.
aCheck disc.
NON PLAYABLE DISC
MECHANISM ERROR
Disc has scratches.
aCheck disc.
No operation by some cause.
aPress [u]. If failure persists, press the reset switch. (Press the reset switch in
the CD changer). If normal operation is not restored, call the store where you
purchased the unit or the nearest Panasonic Service Center.
The type of the file that is selected is not supported.
FILE ERROR
PROTECTED
NO DISC
aCheck disc.
A WMA file can be copyrighted.
aThe file protected by copyright is not playable.
No disc is in the player.
aInsert disc into the disc slot.
No magazine is in the changer.
NO MAGAZINE
REGION ERROR
aLoad the changer with CD-loaded magazine.
An attempt was made to play a disc with a region number other than “3” or “ALL”.
aPress [u] and check the disc.
Note:
¡There may be cases when the disc numbers affected by an error are displayed before “NON PLAYABLE DISC”.
¡Displays and the steps to be taken for errors vary in part from changer to changer. For details, refer to the Operating
Instructions for the changer used.
■ iPod Control
The iPod cable was disconnected in the iPod mode.
aReconnect the iPod cable.
NO iPod
Your iPod has no playable music.
NO SONGS
a
Download playable music to your iPod.
23
CQ-VD7005W
Matsushita Electric Industrial Co., Ltd.
YFM284C676CA PTW0107-2037
Printed in China
|
JVC AV 27S776 User Manual
Maytag MEC4436AAW User Manual
Moxa Technologies Computer Hardware C168HS User Manual
NEC Electronics America Computer Hardware 2000 IVS User Manual
Oricom 8800 User Manual
Panasonic BT 3DL2550P User Manual
Pelco PMCS15A User Manual
Philips 30PW8520 User Manual
Philips 150B5CG User Manual
Philips 170P7 User Manual