OWNER'S MANUAL
71CM CORDLESS REMOTE COLOUR TELEVISION
MODEL: 7128G
Type Tested
Electrical
Safety
AS/NZS 3250 Lic 4166
Standards Australia
APP No: N15899
PALSONIC CORPORATION PTY LTD
1 JOYNTON AVENUE
WATERLOO NSW 2017 AUSTRALIA
TEL:(02)9313 7111
FAX:(02)9313 7555
PALSONIC CUSTOMER SERVICE
TELEPHONE
AUSTRALIA:1300 657 888
INTRODUCTION
Features
.
Hyperband
.
English/Chinese on-screen menu display
.
256 preset channels
Intellectualized I2 C-bus control
.
.
Full function remote control
.
ON Timer, OFF Timer
.
Four picture modes' setting
.
AUDIO/VIDEO input & output terminals
.
S-VIDEO Terminal
.
Program scan function
.
Games calendar function
.
Advanced digital picture improvement circuit
.
Digital AFT technology
.
Channel reservation
1
NOTES FOR OPERATION
Do not let the TV set be in stand-by condition for a long period of time. When it is not in use, please
turn off the power supply and remove the power plug. When it is to be left unattended for
a prolonged period of time, it is recommended to disconnect the connection to the outdoor aerial, to
avoid thunder strike.
*
* Please follow cautions for safety in the TV set instructions, and all warnings and descriptions denoted
on the TV set.
Cautions for safety
Note: This TV set can be operated on an AC power of 240V, 50Hz. You should not use power
supply of the other type.
In order to wipe dust off the
picture tube or off the cabinet,
you should remove the power
plug from the wall outlet first.
You can wipe lightly with a
piece of dry, clean, soft cloth.
When an unusual situation
occurs, turn off the power
switch at once and remove the
plug from the wall outlet.
Contact a qualified service
department in your local area.
Do not expose the TV set to
rain or excessive moisture, to
prevent tire disaster or
electric shock. Avoid using
the set in very warm or damp
places. Never use it in a
bathroom.
The TV set should be placed
on an adequate place without
exposing it to direct sunlight
and other sources of heat to
prevent the deformation of the
cabinet or damage to components.
Do not cover the Ventilating
holes in the cabinet. Keep a
space of more than 5cm from
the walls to the TV set, to
There exists High Voltage in
this TV set. Do not remove
the cover to avoid danger.
guarantee the good ventilation.
When the power cord or the
plug is damaged, please
contact a qualified service
department to get service.
When the TV set is to be left
unattended, please turn off the
power switch and remove the
plug from the wall outlet.
2
Installation
Antenna Connection
To ensure a bright-coloured and clear picture, you should use an outdoor aerial or CATV cable. If
the signals are strong enough, you may use an indoor aerial.
Note: In case of using the
Twin-lead aerial feeder (300 )
for UHF/VHF aerial, use a 300-75
ohm adaptor (not supplied)
When using the coaxial cable (not
supplied) (75 ) for UHF/VHF
aerial, connect the plug into the
75 ohm aerial socket directly.
Note:
When you connect the outdoor aerial cable to the aerial terminal on the TV set, please turn off the
power switch on the TV while connecting the antenna lead.
In thunder and lightning weather, please disconnect the outdoor aerial to avoid thunder/lightning
strike.
Effective range of the remote
control operation
Battery installation
(1) Remove the back battery cover.
(2) Insert two size AAA batteries according to
the polarity indication inside the remote
controller.
Notes:
1.
When the remote controller is not used for
an extended period of time or the batteries
are worn out, please remove the batteries in
time to avoid battery leakage.
Avoid moisture and mechanical shock to
the remote controller.
2.
3.
Do not drop, dampen or disassemble the
remote controller.
3
Appearance
Front view
Note: Functions of MENU, TV/AV, VOLUME+/-, CH
remote controller.
are also provided to the
Back View
4
Appearance
Remote Controller
5
Menu Introduction
Introducing the menu
You can use the on-screen menus to set the picture quality and other settings. You can use buttons on
both the remote controller and the TV to operate the menus.
Notes:
To select each item, use the or
button.
Normal Screen
To adjust or set each item, use the
or
button
Press MENU button
76
75
100
50
COLOR
BRIGHT
CONT
SHARP
SELECT:
SET:
Press MENU button
008
VHFL
OFF
POSITION
BAND
SKIP
SEARCH
MFT
AUTO MEMORY
Press MENU button
ENG/
AUTO
BG
LANGUAGE
C.SYSTEM
S.SYSTEM
B.B SET
ON
SELECT:
SET:
Press MENU button
CALENDAR
GAME 1
GAME 2
SELECT:
SET:
Press MENU button
18.3018
OFF
OFF
-
NOW TIME
ON TIME
OFF TIME
ON CHANNEL
TIME ADJ
0M
SELECT:
SET:
Press MENU button
OFF
-
TIME
CHANNEL
SELECT:
SET:
Press MENU button
6
OPERATION
Turning the Power On/Off
.
The following describes how to turn the TV on/off using the TV's main switch and the remote
controller.
To turn the power on/off
1. Press the POWER switch, the red power indicator lights up.
2.
Press the
button or any one of 0~9 number buttons on the remote controller to
turn the set on and the green indicator lights up.
Without using the remote controller, you can directly press VOL
or TV/AV button on the set to turn on the TV.
or CH
*Note:
If there are no input signals to the TV when the TV set is on, a blue background will
appear on the screen (when B.B (blue back) is set ON.)
After 15 minutes if there are still no signals to the TV, it will enter into standby mode
automatically
3. Press the POWER switch to turn off the set completely.
If you want to turn off the TV temporarily, press the
switch the set to standby mode.
button on the remote controller to
4.
Note:
To prolong the picture tube's life, us a delayed shut-down circuit is adopted. The
functions only when the set is turned on for more than 5 seconds.
button
Special indication:
Auto-Power-Off function: there are two kinds of Auto-Power-Off function:
If a vacant channel is tuned or TV broadcast for a day is finished, and the blue background appears
on the screen, the TV will automatically turn off after about 15 minutes.
1.
2. Sleep-timer function.
3. OFF timer function
7
OPERATION
Tuning in
There are two ways to preset channels: to preset channels automatically and to preset channels
manually. Below we will describe how to preset the channels by making use of the menu.
To preset channels (Auto search)
Use the AUTO SEARCH function to preset all the active channels in your local area automatically.
To enter into menu
Press the MENU button repeatedly to select and
highlight the
appears on the screen automatically.
icon, and the PRESET menu
008
VHFL
OFF
POSITION
BAND
SKIP
SEARCH
MFT
AUTO MEMORY
Press the or button to select the item upward or downward
in the menu, press the
item.
or button to enter into the selected
lllllllllllll
Note: If this manual the MENU button refers to the MENU button on the remote controller or on the
TV set, the or button refers to the or button on the remote controller or CH button
on the TV set, the
or
button refers to the
or
button on the remote controller or the
VOL+/- button on the TV set.
AUTO SEARCH
1.
008
VHFL
OFF
POSITION
BAND
Press the
(PRESET) menu, press the or
button to select AUTO MEMORY.
SKIP
SEARCH
MFT
AUTO MEMORY
lllllllllllll
2.
Press the
button to start the AUTO SEARCH. All
active channels will be preset and stored into the
memory automatically. After presetting, the TV will
return to the first channel program.
AUTO MEMORY 4 VHFL
STOP
3.
During the process of AUTO SEARCH, pressing the
button on the remote controller will stop the
process the and TV will return to the first channel
program.
0
8
OPERATION
Tuning in (continued)
Use the MANUAL SEARCH function if desired channels can not be preset with the
AUTO SEARCH or if you would like to preset channels to specific position numbers one by one.
It is convenient to set the channel numbers to the same position numbers using MANUAL
SEARCH and SKIP functions.
To preset channels (Manual search)
Manual search
If AUTO SEARCH can not preset the desired channels, or you want to preset the desired channels one
by one with the preferred channel numbers, please make use of Manual search.
1.
Press the MENU button repeatedly to enter into the
(PRESET) menu, or press the or button to
008
VHFL
OFF
POSITION
select POSITION. Press the
or
button
BAND
SKIP
to select a desired position number (from
0~255)
SEARCH
MFT
AUTO MEMORY
press the
or
within 0.7 seconds. Press and hold the
for over 0.7 seconds to select a decimal number
button to select a channel number
Note:
lllllllllllll
or button
2.
Press the or button to select SEARCH. Press the
button to search channels from current channel to
higher channel (the screen displays glittering (" ").
008
VHFL
OFF
POSITION
BAND
SKIP
Press the
button to search channels from current channel
SEARCH
MFT
AUTO MEMORY
to lower channel (the screen displays glittering (" ").
When a channel is located, the searching stops, this channel
is then memorised with the preset position number.
lllllllllllll
you can also make use of BAND selection to quicken the
Note:
searching process in your desired band. Press the
button moves the band to the next step in the sequence below.
or
008
VHFL
OFF
POSITION
BAND
SKIP
SEARCH
MFT
AUTO MEMORY
lllllllllllll
VHFL
VHFH
UHF
3. When you want to store another channel at another position, repeat steps 1 & 2 above.
9
OPERATION
Tuning in (continued)
To skip unnecessary position numbers and MFT (Manual Fine Tuning)
To skip a position number
After presetting the channel you can skip unnecessary position numbers so that only the channels you
want to watch are selected.
1.
Enter into the
(PRESET) menu, press the
008
VHFL
OFF
POSITION
BAND
or button to select POSITION , then select
the unwanted program number with the
button.
SKIP
or
SEARCH
MFT
AUTO MEMORY
lllllllllllll
Press the or button to select "SKIP". Press the
or button to select "SKIP ON".
After completion of channel preset , the position
number will then be skipped when you select
2.
008
VHFL
ON
POSITION
BAND
SKIP
SEARCH
MFT
AUTO MEMORY
programs with the CH
button.
If you want to skip other unwanted programs, repeat step 1 above
to change the program number.
lllllllllllll
To restore skip a position number
Enter into the PRESET menu, Select the position number you want to restore. Press the or button to select
"SKIP". Press the or button to select "SKIP OFF".
MFT (Manual Fine Tuning)
When picture and sound's effect of a channel is poor (for example: one or two CATV channel's picture
and sound are not standard), you can correct them by making use of Manual Fine Tuning.
1.
Enter into
(PRESET) menu, select the
008
VHFL
OFF
POSITION
BAND
program number you want to fine-tune.
SKIP
SEARCH
MFT
AUTO MEMORY
lllllllllllll
Press the or button to select MFT, then press
2.
the
or
button, the channel begins fine tuning
until the optimum picture and sound is achieved.
008
VHFL
OFF
POSITION
BAND
SKIP
SEARCH
MFT
AUTO MEMORY
Note: if some channel’s colour or sound is abnormal, it may be that the
setting of the colour is wrong, please do adjustment
according to The setting of colour system (on page 11) to set the
proper colour system.
lllllllllllll
3. To exit the menu, press the MENU button repeatedly or wait for 15 seconds.
10
OPERATION
Tuning in (continued)
The setting of colour system
In factory the TV set's colour system has been preset to AUTO, if you want to change the
system, please do the following adjustments.
Note:
1.
[SYSTEM]
Press the SYS button, the colour and sound
AUTO
BG
COLOR
SOUND
system will be displayed on the screen.
SELECT
ADJUST
If the colour is abnormal, press the or
button to select COLOR, then press the
button to select the proper colour system.
Every time you press the or button,
2.
[SYSTEM]
or
AUTO
BG
COLOR
SOUND
the colour system will change in the sequence
below.
SELECT
ADJUST
358NTSC
AUTO
PAL
443NTSC
Now you can watch the broadcasting TV program on the preset channels.
11
OPERATION
Channel selection
You can watch TV programmes being broadcast on the preset channels.
To watch a TV programme
You can select your desired TV program by one of the following methods.
Using the direct select buttons
To select a one-digit position number (0~9)
METHOD 1:Press the button and the screen displays "X- -", wait for 2
seconds and the channel is selected.
METHOD 2: Press 0 button and the screen displays "0- -", then press 0 button
again, the screen displays "00-" then press the numbers. (The
period of two-press must be within 2 seconds).
After 2
seconds
X--
X
To select a two-digit position number (10~99)
METHOD 1:Press these two numbers and the screen displays "XX -", (The
period of two-press must be within 2 seconds). Wait for 2
seconds and the channel is selected.
X--
XX-
XX
METHOD 2:
Press 0 button first, than press these two numbers, the screen
displays "0XX", the channel is selected. (The period of
two-press must be within 2 seconds).
To select a three-digit position number (100~255)
Press these three numbers and the screen displays "XXX" the channel
is selected. (The period of two-press must be within 2 seconds).
X--
XX-
XXX
NOTE: If the input number is over 255, the screen will remain at the
current viewed program.
Using the CH
buttons
Press CH to select lower position numbers;
CH to select higher ones.
3
2
1
Using the PREVIOUS channel button (
)
When there are no menus on the screen, pressing the
button on the remote controller (below the MENU button)
can swap the current viewed channel with the previous
one. For example, the channel you previously watched is
11
2
11, the present channel is 2, press the
button, it will
return to channel 11, press the
return to channel 2.
button again it will
Using the channel SCAN button
Press SCAN button, the set will scan the channels from first channel to higher channels
one by one, every program will be displayed for about 3 seconds and then go on scanning
until all programs are scanned over and then return to your former viewed program.
During the scanning, press SCAN button again, the set will return to your former viewed
program.
12
OPERATION
Convenient Picture Controls
Selectable picture
To select the picture mode
You can select the picture quality instantly among three
preset modes and one user-set mode.
Press the P.S button to select the desired picture quality.
BRILLIANT, NATURAL, MELLOW and PERSONAL
BRILLIANT
(user-set) can be selected cyclically.
NATURAL
MELLOW
PERSONAL
To set the desired picture quality to the PERSONAL position
Press the MENU button to display the
(PICTURE) menu. Or press the P.M button, to
call up PICTURE menu.
1.
76
75
100
50
COLOR
BRIGHT
CONT
SHARP
Press the or button to select the desired
2.
SELECT
ADJUST
adjusting item, and press the
button to adjust the level.
or
Pressing (PERSONAL)
BRILLIANT NATURAL MELLOW
Item
COLOR
paler
deeper
75
75
50
50
90
40
50
50
70
30
BRIGHTNESS
darker
weaker
softer
lighter
stronger
sharper
greenish
CONTRAST
SHARPNESS
*TINT
100
50
purplish
* TINT is for NTSC system only.
The adjusted level is stored in the PERSONAL position.
13
OPERATION
Convenient Sound Controls and Sleep timer
Adjusting the volume and muting the sound
To adjust the volume
Adjust the volume with the VOL
buttons.
Press the VOL button to decrease the sound.
Press the VOL button to increase the sound.
To mute the sound
The muting function is convenient when you need to pay attention
to surrounding sounds, answer a phone call, receive a visitor, etc.
1.
Press the MUTE button to mute the sound.
MUTE
2. To restore the sound, press the MUTE button again or VOL
buttons.
Sleep timer
SLEEP timer
Making use of the Sleep timer function allows you to have the set
automatically turned off after a preset time, and the TV set set to
standby mode.
Press the SLP button every time, the time displaying
on the screen will change in the sequence below:
SLEEP:30MIN.
120MIN
110MIN.......... 10MIN
OFF
14
OPERATION
System setting
SYSTEM SET
Press the MENU button repeatedly to select and
highlight the icon, and the SYSTEM SET
menu appears on the screen automatically.
ENG/
AUTO
BG
LANGUAGE
C.SYSTEM
S.SYSTEM
B.B.SET
ON
SELECT
ADJUST
To select the language for the OSD
Making use of this function can switch the language for the OSD to either
English or Chinese.
In the
button to select LANGUAGE. Press the
button to select ENGLISH or " " (CHINESE).
(SYSTEM SET) menu, press the or
ENG/
AUTO
BG
LANGUAGE
C.SYSTEM
S.SYSTEM
B.B.SET
or
ON
SELECT
ADJUST
The selected language is displayed in front and the
screen menu is automatically displayed in that
language
Colour system selection
In
button to select C-SYSTEM item.
Press the or button to select proper colour
(SYSTEM SET) menu, press the or
ENG/
AUTO
BG
LANGUAGE
C.SYSTEM
S.SYSTEM
B.B.SET
system, AUTO, PAL, 443NTSC, 358NTSC can be
selected cyclically (refer to setting of colour
system on page 11).
ON
SELECT
ADJUST
Blue background
With the blue background function ON, the TV will automatically
turn blue when no signal is being received.
ENG/
AUTO
BG
LANGUAGE
C.SYSTEM
S.SYSTEM
B.B.SET
In
(SYSTEM SET) menu, press the or
or
button to select B/B SET. Press the
button
to change the blue background setting ON or OFF.
To exit the menu, press the MENU button repeatedly or
wait for 15 seconds.
ON
SELECT
ADJUST
Note: If the receiving signals are weak or are not standard, please set the B.B.SET to OFF, otherwise blue
back will appear on the screen or the program will be lost.
15
OPERATION
Special functions
CALENDAR function (1800-2200)
Enter into the
menu, press the or button to select
CALENDAR, press the
enter into calendar interface.
(SPECIAL FUNCTION)
CALENDAR
GAME1
GAME2
or
button to
In the calendar interface pressing the or
button can switch among the year, month and
SELECT
ADJUST
the date while pressing the
increment or decrement them.
or
button can
JULY 18 2007
SU MO TU WE TH FR SA
To exit the calendar interface, press any one of the buttons on the
remote controller
3
1
8
2
9
6
4
5
7
10
17
24
31
13
20
27
11
18
25
12
19
26
14
21
28
15 16
22 23
29 30
Playing games
To play GAME1 (GOBANG)
Enter into the
menu, press the or button to select
GAME1 item, press the
enter GAME1 interface
(SPECIAL FUNCTION)
CALENDAR
GAME1
GAME2
or
button to
SELECT
ADJUST
To play GOBANG, that is, you play chess with
the machine, Whoever first fills the chessboard with five
continuous chessmen at the same line or diagonal line will win the
game. Pressing the
,
,
,
buttons can move the cursor
upward or downward or leftward or rightward. Press the MENU
button to confirm the position.
To exit the game, press the VOL
button or the CH
button.
16
OPERATION
Special functions
Playing games
To play GAME2 (Falling Cube)
Enter into the
menu, press the or button to select
GAME2 item, press the
enter GAME2 interface.
(SPECIAL FUNCTION)
CALENDAR
GAME1
GAME2
or
button to
SELECT
ADJUST
Press any one of
screen, there are falling cubes, pressing
cubes shape, pressing buttons can move the cubes
,
,
,
buttons to start the game. on the
button can change the
,
leftward or rightward while pressing
falling speed.
button can quicken the
When at the screen's playing area one row has been filled with cubes, the row will disappear, and
your score will gain one point. If two rows disappear at the same time, your score will gain three points.
If three rows disappear at the same time, you score will gain seven points.
The right window provides hints about next cube's shape, you can arrange current cube's position and
and angle in advanced. When the cube reach top, the screen will display GAME OVER, and the game is
finished.
To exit the game, press the VOL
button or the CH
button.
17
OPERATION
CLOCK SETTING
CLOCK SET
Press the MENU button repeatedly to select and highlight the
appears on the screen automatically.
icon, and the CLOCK SET menu
NOW TIME setting
Making use of this function can set the current time for the TV.
In the
(CLOCK SET) menu, press the or
18:30:18
NOW TIME
ON TIME
OFF TIME
ON CHANNEL
TIME ADJ
OFF
OFF
--
button to select NOW TIME. Press the
button to set the current time
or
0M
SELECT
ADJUST
ON TIME setting
Making use of this function can automatically turn on the TV at a
preset time.
In the CLOCK SET menu press the or button to select ON
18:30:18
19:00
OFF
000
0M
NOW TIME
ON TIME
OFF TIME
ON CHANNEL
TIME ADJ
TIME. Press the
or
button to set the TV ON time. In
standby mode, once the TV ON time is in accordance with the
current time, the TV will turn on automatically.
SELECT
ADJUST
OFF TIME setting
Making use of this function can automatically turn off the TV at a
preset time.
In the CLOCK SET menu press the or button to select OFF
18:30:18
OFF
23:00
000
NOW TIME
ON TIME
OFF TIME
ON CHANNEL
TIME ADJ
TIME. Press the
or
button to set the TV OFF time. In
standby mode, once the TV OFF time is in accordance with the
current time, the TV will turn off automatically and be in standby
mode.
0M
SELECT
ADJUST
ON CHANNEL setting
Making use of this function can automatically turn on the TV at a
preset channel
In the CLOCK SET menu press the or button to select ON
18:30:18
19:00
OFF
008
0M
NOW TIME
ON TIME
OFF TIME
ON CHANNEL
TIME ADJ
CHANNEL. Press the
or
button to set the TV ON channel.
If the set's turning on is determined by the ON TIME setting, then
after turning on, the TV will broadcast the preset channel.
Note:
SELECT
ADJUST
1) To fulfill the ON CHANNEL function, you should set ON TIME first.
2) Press the
or
button to set the time. If you press the button within 0.7 seconds, the minute
will increase or decrease by 1; if you press the button for more than 0.7 seconds, the
minute will increase or decrease by 20.
3) Once the function of ON/OFF TIME has been fulfilled, next when you want to use the function
once more you should set them again.
Time adjustment
Making use of this function can adjust the built-in clock.
In the CLOCK SET menu press the or button to select TIME
18:30:22
OFF
OFF
--
-10M
NOW TIME
ON TIME
OFF TIME
ON CHANNEL
TIME ADJ
ADJ item. press the
or
button to adjust the value. If you
discover the built-in clock is quicker or slower than standard time,
for example, every day it will be quicker for about 10 minutes, then
you can set the value to -10 MIN to adjust the clock
SELECT
ADJUST
To exit the menu, press the MENU button repeatedly or wait 15 seconds.
18
OPERATION
Channel reservation
To reserve the channel
Making use of this function can switch the channel to your desired
channel you reserve at a preset time.
OFF
--
TIME
CHANNEL
Press the MENU button repeatedly to select and
highlight the
icon, and the RESERVE menu
appears on the screen automatically
SELECT
SET
Time setting
Making use of this function to set the time to switch the channel to
the reserved channel.
19:28
TIME
Press the or button to select TIME.
000
CHANNEL
Press the
or
button to set the time.
To exit the menu, press MENU button repeatedly or
wait 15 seconds.
SELECT
SET
Channel setting
Making use of this function to set the reserved channel.
19:28
TIME
Press the or button to select CHANNEL, then
press the or button, the channel number.
When the set's current time is in accordance with the
time which you set in the (RESERVE) menu,
005
CHANNEL
SELECT
SET
the set will automatically switch to the reserved
channel.
To exit the menu, press the MENU button repeatedly or wait for 15 seconds.
Note:
1. To fulfill the RESERVE function, you should set the time firstly, the set the reserved channel.
2. Once the RESERVE function has been fulfilled, next when you want to use the function once
more, you should set them again.
19
CONNECTING OTHER EQUIPMENT
External Equipment Connections
.
The following describes how to use and connect the TV with other AV equipment. Refer to
the owner’s manual of the equipment to be connected as well.
To connect AV input terminal
You can connect video equipments such as a VTR and video camera to this TV and enjoy the high
quality picture and sound.
If your video equipment has a S-VIDEO output terminal, connect it to the S-VIDEO input terminal
(special S-VIDEO type) of the unit. If not, connect it to the VIDEO terminal (photo type).
20
CONNECTING OTHER EQUIPMENT
To connect AV input terminal (continued)
To select the video input, press TV/AV the button on the TV set or AV button on the remote controller
repeatedly until you see the corresponding input indication on the screen. To return to aerial input,
press the AV button until it displays program number, or press channel select button or the CH
button.
VIDEO 3
TV
VIDEO 1
VIDEO 2
(S-VIDEO)
If the colour of video input is abnormal, the colour system setting may be incorrect. Press the SYS
button until the COLOR AUTO is displayed on the screen. If the picture is still abnormal,
press the
or
button until normal colour appears.
NOTE on the S-VIDEO terminal
The S-VIDEO input terminal has priority over Video 1 VIDEO terminal. If S-VIDEO input terminal is
used, the screen will display "S-VIDEO1". To use the equipment connected to AV1 VIDEO terminal,
disconnect any plug from the S-VIDEO terminal
To connect MONITOR output terminal
You can connect a stereo system to the MONITOR output terminals (photo type) on the set to
enjoy a high-quality sound from the stereo system. The MONITOR output terminals output the
video and audio signals being displayed on the screen.
21
OTHERS
Troubleshooting Guide
.
Before calling service personnel, please check the following chart for a possible cause to the
trouble you are experiencing.
Check the following items
Symptoms
No power, red indicator is not lit up
Poor colour, poor tint
.
.
Be sure the power cord is plugged in.
Contrast, colour, tint are not correctly
adjusted
.
.
Possible interferences of automobiles,
motorcycle, trolley bus, neon lamps, etc.
Possible interference of electronic
interference from another TV set, a
computer, an electronics game machine, a
broadcast station, etc.
Spots appear on the screen
Stripes appear on the screen
.
This may be caused by reflections from
nearby mountains or buildings.
Check the antenna direction.
Double images or "ghosts"
Snowy picture
.
.
It is possible that the aerial “lead-in” is
damaged or comes off.
Check the antenna direction
.
.
The batteries may be worn out.
The batteries may be installed with their
polarity reversed.
.
The remote controller does not work
.
Even if the picture or the sound is normal,
changes in the room temperature
sometimes make the TV cabinet expand or
contract, making a noise. This does not
indicate a malfunction.
TV cabinet creaks
Specifications
AC 240V, 50Hz
140W
737 (W) x 610 (H) x 519 (D)
45
Power supply:
Power consumption:
Dimensions (mm):
Weight (kg):
71cm
CRT
TV system & channel range
UHF
21-69
CATV
X~Z+2, S1~S41
System
PAL-B/G
VHF
2-12
PAL-BG, NTSC 3.58/4.43 (AV)
5W + 5W
Colour system:
Sound output:
Accessory:
one remote controller
* Note: Design and specifications are subject to change without notice.
22
PALSONIC CORPORATION PTY LTD
1 JOYNTON AVENUE
WATERLOO NSW 2017 AUSTRALIA
TEL:(02)9313 7111
FAX:(02)9313 7555
PALSONIC CUSTOMER SERVICE
TELEPHONE
AUSTRALIA: 1300 657 888
604-25AA3-09
|