Marshall Electronics
V-R1042DP-DVI
High Definition Dual Screen LCD Monitor Set
Operating Instructions
Marshall Electronics, Inc.
1910 East Maple Ave.
El Segundo, CA 90245
Tel: (800) 800-6608 / (310) 333-0606 • Fax: 310-333-0688
20
Warranty
Contents
Product Overview.....................................................................................................................................................4
Features ....................................................................................................................................................................4
Marshall Electronics warranties to the first consumer that this V-R1042DP-DVI LCD monitor will, under normal use, be
free from defects in workmanship and materials, when received in its original container, for a period of one year from the
purchase date. This warranty is extended to the first consumer only, and proof of purchase is necessary to honor the
warranty. If there is no proof of purchase provided with a warranty claim, Marshall Electronics reserves the right not to
honor the warranty set forth above. Therefore, labor and parts may be charged to the consumer. This warranty does not
apply to the product exterior or cosmetics. Misuse, abnormal handling, alterations or modifications in design or
construction void this warranty. It is considered normal for a minimal amount of pixels, not to exceed three, to fail on the
periphery of the display active viewing area. Marshall Electronics reserves the option to refuse service for display pixel
failure if deemed unobtrusive to effective use of the monitor by our technicians. No sales personnel of the seller or any
other person is authorized to make any warranties other than those described above, or to extend the duration of any
warranties on behalf of Marshall Electronics, beyond the time period described above. Due to constant effort to improve
products and product features, specifications may change without notice.
Installation and Initial Setup ...................................................................................................................................5
Unpacking..............................................................................................................................................................5
Installation..............................................................................................................................................................5
Connections and Power-On...................................................................................................................................5
Front Panel Features ...............................................................................................................................................6
Power Button ........................................................................................................................................................6
Input Select Buttons...............................................................................................................................................6
On-Screen Menu Navigation Buttons ....................................................................................................................6
User-Definable Function Buttons...........................................................................................................................6
Image Adjustment Knobs.......................................................................................................................................6
Tally Lights.............................................................................................................................................................6
11/05/07
Rear Panel Features.................................................................................................................................................7
Power Input............................................................................................................................................................7
Signal Input/Output ................................................................................................................................................7
Tally Interface ........................................................................................................................................................7
Compatible Input Formats.......................................................................................................................................8
On-Screen Menu.......................................................................................................................................................9
STRUCTURE OVERVIEW ....................................................................................................................................9
MAIN MENU AND NAVIGATION ..........................................................................................................................9
MARKER SETUP SUBMENU .............................................................................................................................10
16:9 Markers....................................................................................................................................................10
4:3 Markers......................................................................................................................................................11
Marker Background .........................................................................................................................................11
Center Marker..................................................................................................................................................11
VIDEO CONFIGURATION SUBMENU ...............................................................................................................12
Color Temperature Presets .............................................................................................................................12
Adjusting Color Bias ........................................................................................................................................12
Adjusting Color Gain........................................................................................................................................12
Monochrome Mode..........................................................................................................................................13
Blue Only Mode...............................................................................................................................................13
Pixel-to-Pixel Mode..........................................................................................................................................13
Aspect Ratio Setting........................................................................................................................................14
Scanning Modes..............................................................................................................................................14
Delay Modes....................................................................................................................................................14
SYSTEM CONFIGURATION SUBMENU............................................................................................................15
Internal SMPTE Color Bars .............................................................................................................................15
User-Definable Function Buttons ....................................................................................................................15
Status Display..................................................................................................................................................15
Saving and Loading User Configuration Presets ............................................................................................15
Specifications.........................................................................................................................................................16
Maintenance............................................................................................................................................................17
Warranty..................................................................................................................................................................18
18
3
Specifications (continued)
Product Overview
The V-R1042DP-DVI is a dual screen high definition LCD monitor set featuring our completely digital TFT-MegaPixel™
active matrix LCD platform. Utilizing 10.4-inch panels with 2.4 million pixels each, the V-R1042DP-DVI provides the
highest pixel density available while occupying only 4RU. Our proprietary digital signal processing features 10-bit A/D
conversion of all analog signals, with 4X over-sampling and 5-line super-adaptive 2D comb filtering of composite
signals. Emulation of SMPTE-C/EBU color and adjustable color temperature enable the most precise color
representation possible. De-interlacing is performed using our HyperProcess algorithm with motion adaptive
interpolation. Multi-format compatibility accommodates virtually all video formats including NTSC/PAL, 480i/p, 720p,
and 1080i standards. VGA and DVI inputs accept VESA standards allowing the display to be used as a computer
monitor. Advanced features include aspect ratio settings, a variety of screen markers, underscan mode, blue-only
mode, monochrome mode, H/V delay, and Pixel-to-Pixel mode.
Features
■
■
■
High-Resolution Dual 10.4” Panels
The V-R1041DP-DVI features an all-digital TFT-MegaPixel™ active matrix LCD system with 2.4 million pixels. Each
LCD panel features a brightness of 400 cd/m2, 400:1 contrast ratio, and a 170° all-around viewing angle making the
display ideal in a variety of environments and lighting conditions.
Multi-Format Compatibility
With analog and digital inputs, the V-R01042DP-DVI accommodates many video formats. Input types include VGA and
DVI with HDCP. Accepted formats include 480i/p, 576i/p, 720p, and 1080i standards, as well as VESA PC formats
through SXGA (1280 x 1024).
End-to-End Digital Signal Processing
Analog signals are digitized using an advanced 10-bit process with 4x over-sampling, 5-line super-adaptive 2D comb
filtering, and exacting color space conversion. Video is scaled to fit on the screen in the highest possible resolution
using a state-of-the-art LSI that incorporates precision gamma correction and our HyperProcess motion adaptive
interpolation for interlaced images.
Maintenance
■
Screen Cleaning
■
■
ColorMatch Conversion with Color Temperature Adjustment
Emulation of SMPTE-C/EBU color space allows the V-R1042DP-DVI to replace any broadcast CRT monitor. Settings
include D55, D65 and D95. Bias and Gain adjustment for each color enables precise color matching and white
balance.
Periodically clean the screen surface using ammonia-free cleaning wipes (Marshall Part No. V-HWP-K). A clean micro-
fiber cloth can also be used using only non-abrasive and ammonia-free cleaning agents. Do not use paper towels.
Paper towel fibers are coarse and may scratch the surface of the polycarbonate faceplate or leave streaks on the
surface. Antistatic and fingerprint resistant cleaning agents are recommended. Do not apply excessive pressure to the
screen to avoid damaging the LCD.
Advanced Features
Aspect ratio settings, underscan mode, blue-only mode, monochrome mode, and H/V delay are a few of the advanced
features making the V-R1042DP-DVI at home in any broadcast environment. Pixel-to-Pixel mode also allows native
display of any incoming image format. Underscan and H/V delay are available only when monitoring standard-
definition formats.
■
Faceplate Dusting
Dust the unit with a soft, damp cloth or chamois. Dry or abrasive cloths may cause electrostatic charge on the surface,
attracting dust particles. Neutralize static electricity effects by using the recommended cleaning and polishing practice.
■
■
Flexible Screen Markers
A variety of screen markers in both 4:3 and 16:9 modes allow accurate monitoring of the different aspect ratios used in
broadcast environments.
User-Definable Function Buttons
Two user-assignable function buttons allow quick access to numerous settings and features including aspect ratio,
screen markers, monochrome mode, color temperature, delay mode, and more.
4
17
Specifications
Installation and Initial Setup
■
■
PANEL
TALLY
■
Unpacking
Screen Size
Display Area (h x v)
Aspect Ratio
Pixels
Color Depth
Viewing Angle (h x v) 170° x 170°
10.4” Diagonal
3 LEDs (Green, Red, Yellow). Activation requires contact
closure of pin to ground on the HD-15 connector:
210.432 x 157.824 mm
4:3 Native (4:3/16:9 Modes)
1024 x RGB x 768
Carefully unpack the V-R1042DP-DVI monitor and verify that the following items are included:
Pin No.
1
2
3
4
5
6
Signal
M1 Green
M1 Red
M1 Yellow
Ground
Ground
N/C
• V-R1042DP-DVI Monitor
• V-PS12-5V-1 Power Supply with 2-Pin Twist Lock Connector
• Operating Instructions
24-bit (16,777,216 Colors)
Brightness
300 cd/m2
700:1
0.0685 x 0.2055 mm
0.2055 x 0.2055 mm
Contrast Ratio
Dot Pitch (h x v)
Pixel Pitch (h x v)
7
N/C
Inspect the unit for any physical damage that may have occurred during shipping. Should there be any damage,
immediately contact Marshall Electronics at (800) 800-6608. If you are not located within the continental United States,
call +1 (310) 333-0606.
8
N/C
9
N/C
10
11
12
13
14
15
N/C
M2 Green
M2 Red
M2 Yellow
Ground
Ground
■
VIDEO INPUT/OUTPUT
■
Installation
VGA Input
The V-R842DP-DVI can be mounted in any standard EIA 19” equipment rack. Adequate ventilation is required when
installed to prevent possible damage to the monitor’s internal components.
■
ELECTRICAL
Supports RGBHV, RsGsBs, RGsB, RGB CS,
Power Consumption 3.5A @ 12VDC (42 W)
Voltage Requirement 12 VDC
DVI Input
Supports Digital Signals Only (DVI-D)
HDMI, HDCP Supported
V-PS12-5V-1 Power Supply:
Input
Output
100V-240V, 1.5A, 50-60Hz
12VDC, 5A, 60W Max
■
CONNECTORS
Video Input
VGA
DVI
1 x HD-15 Female
1 x DVI-I 29-Pin Female
■
MECHANICAL
Power Input
Dimensions (w x h x d): 18.98” x 8.67” x 1.77”
Weight (Monitor Only): 6.40 lbs
2-Pin Twist Lock Connector
Tally Interface
HD-15 Female
Operating Temperature 32°F to 120°F (0°C to 50°C)
Storage Temperature
-4°F to120°F (-20°C to 50°C)
Compliance
₠, FCC-Class A, ANSI-63.4
(Certificates on file)
■
Connections and Power-On
RoHs
Do not dispose. Return to
Manufacturer or Authorized
Recycle Facility.
Plug the V-PS12-5V-1 power supply into an AC power source (100-240 V @ 50/60 Hz). Attach the 2-pin twist lock
connector to the back of the monitor. Please note that 12VDC can be also supplied directly to the monitor from a
variety of sources. The monitor will draw approximately 3.5 Amps at 12 Volts in operation.
Connect the required cables for video signal input and output.
Each screen may be turned on by pressing the power button located on the front panel. Select a video input by
pressing the corresponding input select button.
16
5
On-Screen Menu (continued)
Front Panel Features
SYSTEM CONFIGURATION SUBMENU
6
Top Front Panel
Video Configuration Submenu
■
■
Internal SMPTE Color Bars
Use to display internally generated SMPTE split-field color bars.
Lower Front Panel
User-Definable Function Buttons
1
4
5
2
3
Use the FUNCTION 1 and FUNCTION 2 menu items to define each function button on the front panel of the monitor.
The following options are available for each button:
• DELAY
• RATIO
• BACK
Enable and rotate amongst delay modes.
Toggle between 4:3 and 16:9 aspect ratios.
Rotate amongst marker backgrounds.
• CENTER
• MARKER
• MONO
• CTEMP
• PTP
Enable/disable center marker.
Enable and rotate amongst marker settings (choices depend on aspect ratio setting).
Enable/disable monochrome mode.
Rotate amongst color temperature settings.
Enable/disable Pixel-to-Pixel mode.
1
Power Button
User-Definable Function Buttons
4
Turn the monitor on by pressing the power button.
In the OFF state, the LED will shine red. The LED
will shine green when the monitor is turned on.
Two user-definable function buttons can be used for
direct access to various settings. Functions are
assigned using the on-screen menu (See User-
Definable Function Buttons – Page 15).
FUNCTION 1 is set to RATIO by default.
FUNCTION 2 is set to PTP by default.
Input Select Buttons
2
Image Adjustment Knobs
5
Use the input select buttons to select the input to be
displayed:
■
■
Status Display
Use the image adjustment knobs to adjust the
following settings. Pressing each knob will display
the current status of the corresponding control:
Use to enable on-screen display of input/format status in the upper-left corner of the screen.
•
•
VGA
DVI
•
•
•
Brightness (0-64)
Color (0-64)
Contrast (0-64)
Saving and Loading User Configuration Presets
Each input automatically detects the applicable
formats (See Compatible Input Formats – Page 8).
Use the SAVE CONFIG and LOAD CONFIG menus to save current settings to one of 6 presets, or load a preset. All
monitor settings on the monitor are saved, including the image adjustment knob settings.
On-Screen Menu Navigation Buttons
Tally Lights
3
6
•
•
Use the LOAD CONFIG menu to load one of presets USR1 – USR6. Factory default settings can also be loaded
by selecting MFG. (Factory defaults cannot be overwritten.)
Use the Menu, ↑, ↓, and Select buttons to display
and navigate the on-screen menu (See Main Menu
and Navigation – Page 9).
Three tally LEDs (green, red, and yellow) are
provided as general purpose indicators. Each LED
can be individually controlled, providing multiple
indications. Tally LEDs are controlled via the HD-15
connector on the rear panel (See Tally Interface –
Page 7)
Use the SAVE CONFIG menu to save the current settings to a preset from USR1- USR6.
6
15
On-Screen Menu (continued)
Rear Panel Features
VIDEO CONFIGURATION SUBMENU (continued)
■
Aspect Ratio Settings
Use to switch between 4:3 and 16:9 aspect ratios.
1
3
As the V-R1042DP-DVI monitor has a native resolution of 1024 x 768 RGB pixels, incoming images are automatically
scaled to fit the screen:
•
•
In 4:3 mode, images are scaled up or down to fill the entire 4:3 screen (1024 x 768).
In 16:9 mode, images are scaled to fill the maximum 16:9 portion of the screen (1024 x 576), with black bars filling
the remainder of the screen.
2
1
Power Input
3
Tally Interface
4:3 Mode
16:9 Mode
Connect the 12VDC input to the 2-Pin twist lock power
input connector. Power can be supplied from the
included power supply, or from a variety of DC sources
supplying at least 3.5 Amps at 12 Volts.
Each tally light is activated via the HD-15 connector by
connecting the corresponding pin to ground. A variety of
external devices can be used to perform the contact
closure. No additional power should be supplied to the
HD-15 port.
Note: The aspect ratio setting is ignored when Pixel-to-Pixel mode is enabled.
■
IMPORTANT: If using a power source other than the
included power supply, be sure that the polarity of the
DC input is correct:
Scanning Modes
Tally Interface: HD-15 Pinout
Use this setting to switch between normal and underscan modes:
Pin No.
1
2
3
4
5
6
Signal
M1 Green
M1 Red
M1 Yellow
Ground
Ground
N/C
•
•
In normal scan mode, the active portion of the video signal is displayed on the screen, with 0% overscan.
2
Signal Input/Output
In underscan mode, area around the active video area is displayed on the screen, resulting in blanking intervals
being shown around the perimeter of the active image. Use this mode to clearly view the edges of the active video
area.
7
N/C
Connections:
8
N/C
9
N/C
10
11
12
13
14
15
N/C
•
•
VGA (HD-15)
DVI (29-Pin connector, DVI-D signals only)
M2 Green
M2 Red
M2 Yellow
Ground
Ground
■
Delay Modes
Use this setting to enable one of three delay modes (H/V, H, V):
•
In H/V delay mode, both horizontal sync and vertical sync are delayed, resulting in both horizontal and vertical
blanking periods being shown on the screen.
•
•
In V delay mode, vertical sync is delayed so that the vertical blanking period is displayed on screen.
In H delay mode, horizontal sync is delayed so that the horizontal blanking period is displayed on the screen.
Note: Delay modes are only available in normal scan mode.
14
7
On-Screen Menu (continued)
Compatible Input Formats
VIDEO CONFIGURATION SUBMENU (continued)
Format
Composite
S-Video
YPbPr
SDI
VGA
DVI-D
■
Monochrome Mode
NTSC
Use this setting to enable monochrome mode. Only the luminance of the image will be displayed as a grayscale
picture.
PAL
525i
●
●
625i
■
Blue-Only Mode
486p / 59.94
576p / 50
●
●
Use this setting to enable Blue-Only mode. This mode displays only the blue color component of the image, switching
off the red and green components. Use this mode when calibrating the monitor to SMPTE color bars with the following
procedure:
1035i / 60
1035i / 59.94
1080i / 60
1.
2.
3.
4.
Allow the monitor to warm up for at least 5-10 minutes.
●
●
●
●
●
●
●
●
●
●
Display SMPTE split-field color bars on the monitor using the internal generator or an external source.
Enable Monochrome mode.
1080i / 59.95
1080i / 50
Locate the pluge pattern (super black, black, and gray bars) at the lower-right corner of the screen. Adjust the Brightness knob until there is
no visible difference between the super black and black bars, but the gray bar is still visible.
1080psF / 24
1080psF / 23.98
1080p / 30
5.
6.
7.
8.
Adjust the Contrast knob until an even grayscale appears along the top bars.
Disable Monochrome mode.
Enable Blue-Only mode and adjust the Color knob so that the outermost bars (white and blue) appear to match in brightness.
Disable Blue-Only mode.
1080p / 29.97
1080p / 25
720p / 60
●
●
●
●
●
●
■
Pixel-to-Pixel Mode
720p / 59.94
720p / 50
Use this setting to enable Pixel-to-Pixel mode.
720p / 30
This mode bypasses the monitor’s internal scaling function and displays incoming images in their native resolution and
aspect ratio, with a one-to-one mapping:
720p / 29.97
720p / 25
•
•
For incoming formats smaller than the native resolution of the LCD panel (1024 x 768), the image will be
displayed in the center of the screen using only the necessary LCD pixels.
640 x 480 @ 60Hz
640 x 480 @ 75Hz
640 x 480 @ 85Hz
800 x 600 @ 60Hz
800 x 600 @ 75Hz
800 x 600 @ 85Hz
1024 x 768 @ 60Hz
1024 x 768 @ 75Hz
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
For incoming formats exceeding 1024 x 768 pixels, only the center 1024 x 768 of the incoming image will
displayed occupying the whole screen, with the remainder of the picture cropped. For example, 1080i formats will
both be cropped to 1024 x 768 and displayed full-screen.
Note: Pixel-to-Pixel mode will utilize the entire screen (1024 x 768) regardless of the aspect ratio setting.
1024 x 768 @ 85Hz
1280 x 1024 @ 60Hz
●
●
●
●
8
13
On-Screen Menu (continued)
On-Screen Menu
VIDEO CONFIGURATION SUBMENU
STRUCTURE OVERVIEW
OFF, 13:9, 14:9, 4:3, 2.35:1,
1.85:1, 95%, 93%, 90%,
88%, 80%
MARKER 16:9
MARKER 4:3
MARKER SETUP
OFF, 95%, 93%, 90%, 88%,
80%
MARKER BACKGROUND
CENTER MARKER
COLOR TEMP
OFF, HALF, BLACK
OFF, ON
D55, D65, D93, USER
RED (0-100)
GREEN (0-100)
BLUE (0-100)
RED (0-100)
GREEN (0-100)
BLUE (0-100)
OFF, ON
Video Configuration Submenu
ADJ COLOR BIAS
ADJ COLOR GAIN
■
■
Color Temperature Presets
Use this setting to choose one of three color temperature presets:
• D55 (5500K)
• D65 (6500K)
• D93 (9300K)
• USER (Adjustable Color Bias and Gain)
VIDEO CONFIG
MONO
BLUE ONLY
PIXEL TO PIXEL
ASPECT RATIO
SCAN
OFF, ON
MAIN
OFF, ON
4:3, 16:9
NORMAL, UNDER
OFF, H/V, V, H
OFF, ON
Adjusting Color Bias
DELAY
SMPTE BAR
DELAY, RATIO, BACK,
CENTER, MARKER, MONO,
CTEMP, PTP
FUNCTION 1
DELAY, RATIO, BACK,
CENTER, MARKER, MONO,
CTEMP, PTP
FUNCTION 2
SYSTEM CONFIG
STATUS DISPLAY
LOAD CONFIG
OFF, ON
Color Bias Menu
USR1, USR2, USR3, USR4,
USR5, USR6, MFG
Use this submenu to adjust bias of the color response. Adjust the bias for each color to alter the white balance of the
image. The Color Temperature preset will automatically switch to USER when Color Bias settings are adjusted. It is
normal for color bias adjustments to be very subtle.
USR1, USR2, USR3, USR4,
USR5, USR6
SAVE CONFIG
■
Adjusting Color Gain
MAIN MENU AND NAVIGATION
Access the main menu by pushing and holding the MENU button on the front panel of the monitor.
•
•
•
•
•
•
Step through menu items using the ↑ and ↓ buttons.
Choose a menu item by pressing SELECT.
Rotate through options using the ↑ and ↓ buttons.
Choose a setting by pressing SELECT.
Return to the previous menu by pressing MENU.
Exit the main menu by pressing MENU. The menu will automatically
time out after 8 seconds. After exiting the menu, wait 1-2 seconds
before displaying the menu again.
Color Gain Menu
Use this submenu to adjust gain of the color response. The Color Temperature preset will automatically switch to
USER when Color Gain settings are adjusted.
Main Menu
12
9
On-Screen Menu (continued)
On-Screen Menu (continued)
MARKER SETUP SUBMENU
MARKER SETUP SUBMENU (continued)
■
4:3 Markers
Use this setting to superimpose one of 5 markers on the screen when in 4:3 mode. This setting is disabled when the
aspect ratio is set to 16:9, or when Pixel-to-Pixel, Underscan, or H/V Delay is enabled.
• OFF (No Marker)
• 95% Safe Area
• 93% Safe Area
• 90% Safe Area
• 88% Safe Area
• 80% Safe Area
4:3 Marker Examples:
■
16:9 Markers
Use this setting to superimpose one of 10 markers on the screen when in 16:9 mode. This setting is disabled when the
aspect ratio is set to 4:3, or when Pixel-to-Pixel, Underscan, or H/V Delay is enabled.
• OFF (No Marker)
• 13:9 Aspect Ratio
• 14:9 Aspect Ratio
• 4:3 Aspect Ratio
• 2.35:1 Aspect Ratio
• 1.85:1 Aspect Ratio
• 95% Safe Area
• 93% Safe Area
• 90% Safe Area
• 88% Safe Area
• 80% Safe Area
OFF (No Marker)
90% Safe Area
■
Marker Background
Use this setting to choose how selected markers are displayed on the screen:
• OFF
• Half-tone Image area beyond the marker is shown at 50% intensity.
• Black Image area beyond the marker is shown at 0% intensity (black).
The marker is superimposed on the complete image.
16:9 Marker Examples:
Example (80% Marker in 4:3 Mode):
Background OFF
Half-tone Background
Black Background
OFF (No Marker)
90% Safe Area
■
Center Marker
Use this setting to display a center marker on the screen. This feature is not available when H/V delay is on.
2.35:1 Aspect Ratio
4:3 Aspect Ratio Marker
Center Marker
10
11
|