User’s Guide
M1717S
M1917S
Make sure to read the Important Precautions before using the product.
Keep the User's Guide(CD) in an accessible place for furture reference.
See the label attached on the product and quote this information to your
dealer when you require service.
Important Precautions
On Installation
Do not allow anything to rest upon or roll over the power cord, and do not place
the display where the power cord is subject to damage.
Do not use this display near water such as near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming pool.
Displays are provided with ventilation openings in the cabinet to allow the release
of heat generated during operation. If these openings are blocked, built-up heat
can cause failures which may result in a fire hazard. Therefore, NEVER:
Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.
Place the display in a built-in enclosure unless proper ventilation is provided.
Cover the openings with cloth or other material.
Place the display near or over a radiator or heat source.
Do not rub or strike the Active Matrix LCD with anything hard as this may scratch,
mar, or damage the Active Matrix LCD permanently.
Do not press the LCD screen with your finger for a long time as this may cause
some afterimages.
Some dot defects may appear as Red, Green or Blue spots on the screen.
However, this will have no impact or effect on the display performance.
If possible, use the recommended resolution to obtain the best image quality for
your LCD display. If used under any mode except the recommended resolution,
some scaled or processed images may appear on the screen. However, this is
characteristic of the fixed-resolution LCD panel.
On Cleaning
Unplug the display before cleaning the face of the display screen.
Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display
screen because over-spraying may cause electrical shock.
On Repacking
Do not throw away the carton and packing materials. They make an ideal
container in which to transport the unit. When shipping the unit to another
location, repack it in its original material.
On Disposal
The fluorescent lamp used in this product contains a small amount of mercury.
Do not dispose of this product with general household waste.
Disposal of this product must be carried out in accordance to the regulations of
your local authority.
A2
Connecting the Display
Before setting up the monitor, ensure that the power to the monitor, the
computer system, and other attached devices is turned off.
Connecting the stand base
1. Place the monitor with its front facing downward on a cushion or soft cloth.
2. Align the hooks on the stand base with the matching slots in the base of
the monitor.
Hook
3. Insert the hooks into slots.
Removing the stand base
1. Place the monitor with its front facing downward on a cushion or soft cloth.
2. To remove the stand base, hold the bottom of the stand with one hand and
pull the base bottom latch with the other hand, as shown in the figure.
Bottom Latch
Important
This illustration depicts the general model of connection. Your monitor may differ from
the items shown in the picture.
Once you connect the stand base, try not to disconnect it.
Do not carry the product upside down holding only the stand base. The product may
fall and get damaged or injure your foot.
A3
Connecting the Display
Before setting up the monitor, ensure that the power to the monitor, the computer
system, and other attached devices is turned off.
Positioning your display
1. Adjust the position of the panel in various ways for maximum comfort.
Tilt Range : 3˚~25˚
Swivel :345˚
Ergonomic
It is recommended that in order to maintain an ergonomic and comfortable viewing
position, the forward tilt angle of the monitor should not exceed 5 degrees.
A4
Connecting the Display
Using the Computer
1. Place the monitor in a convenient, well-ventilated location near your computer.
2. Connect the signal cable. When attached, tighten the thumbscrews to secure the
connection.
3. Connect the power cord into a proper power outlet that is easily accessible and close to
the display.
Power Cord
Signal Cable
Varies according to model.
Wall-outlet type
This is a simplified representation
NOTE
of the rear view.
This rear view represents a
general model; your display may
differ from the view as shown.
2
1
PC-outlet type
PC
MAC
Mac adapter
For Apple Macintosh use, a separate plug adapter is needed to
change the 15 pin high density (3 row) D-sub VGA connector on
the supplied cable to a 15 pin 2 row connector.
4. Press
button on the front switch panel to turn the power
on. When monitor power is turned on, the 'Self Image
Setting Function' is executed automatically.
NOTE
‘ Self Image Setting Function’? This function provides the user with optimal display settings.When the user
connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual
input signals. If you want to adjust the monitor while in use, or wish to manually run this function once again, push
the ‘AUTO/SET’ button on the front panel of the monitor. Otherwise, you may execute the ‘ Factory reset’ option on
the OSD adjustment menu. However, be aware that this option initializes all the menu items except ‘Language’.
A5
Connecting the Display
Bottom
PC AUDIO
Headphone/Earphone Input
Automatically mutes the speaker volume
when the headphones are plugged in.
Audio Input
Connects to the *LINE OUT jack of the
PC sound card.
<Display - Back>
Speaker Out
*LINE OUT
A terminal used to connect to the
speaker including a built-in amplifier
(Amp). Make sure that the connecting
terminal of the PC sound card is checked
before connecting. If the Audio Out of PC
sound card has only Speaker Out,
reduce the PC volume.
*Line Out
If the Audio Out of the PC sound card
supports both Speaker Out and Line Out,
convert to Line Out using the card
jumper of the program (Refer to the
Sound Card Manual).
<Jack of the PC sound card>
A6
Control Panel Functions
Front Panel Controls
Control
Function
Power Button
Use this button to turn the display on or off.
This Indicator lights up blue when the display
operates normally(On Mode). If the display is in Sleep
Mode (Energy Saving), this indicator color changes
to amber.
Power Indicator
Use this button to enter a selection in the On Screen
Display.
AUTO/SET
Button
AUTO IMAGE ADJUSTMENT
When adjusting your display settings, always press
the AUTO/SET button before entering the On Screen
Display(OSD). This will automatically adjust your
display image to the ideal settings for the current
screen resolution size (display mode).
The best display mode is
17 inch monitor : 1280x1024
19 inch monitor : 1280x1024
A7
Control Panel Functions
Front Panel Controls
Control
Function
Use these buttons to decrease or increase
the volume level.
VOL Buttons
Use these buttons to select or adjust functions in the On
Screen Display.
Buttons
Lightview hot key
This feature lets you easily select the best desired
image condition optimized to the environment
(ambient illumination, image types etc).
DAY
NIGHT
• DAY : Bright ambient illumination
• NIGHT : Dark ambient illumination
• TEXT : For text images (Word processing etc.)
• MOVIE : For animation images in videos or movies
• PHOTO : For pictures or drawings
•
NORMAL : This is under normal operating conditions
Use this button to enter or exit the On Screen Display.
MENU Button
OSD LOCKED/UNLOCKED
This function allows you to lock the current control
settings, so that they cannot be inadvertently changed.
Press and hold the MENU button for servaral seconds.
The message "OSD LOCKED" should appear.
You can unlock the OSD controls at any time by pushing
the MENU button for servaral seconds. The message
"OSD UNLOCKED" should appear.
MUTE Button
Used to select mute on (means sound off) and
mute off (means sound on).
A8
On Screen Display (OSD) Control Adjustment
Screen Adjustment
Making adjustments to the image size, position and operating parameters of
the display is quick and easy with the On Screen Display Control system.
A short example is given below to familiarize you with the use of the controls.
The following section is an outline of the available adjustments and selections
you can make using the OSD.
NOTE
Allow the display to stabilize for at least 30 minutes before making image adjustments.
To make adjustments in the On Screen Display, follow these steps:
MENU
AUTO/SET
MENU
MENU
Press the MENU Button, then the main menu of the OSD appears.
To access a control, use the
or
Buttons. When the icon you want
becomes highlighted, press the AUTO/ SET Button.
Use the
Buttons to adjust the item to the desired level.
Accept the changes by pressing the MENU Button.
Exit the OSD by pressing the MENU Button.
A9
On Screen Display(OSD) Selection and Adjustment
The following table indicates all the On Screen Display control, adjustment,
and setting menus.
Main menu
Sub-menu
Reference
BRIGHTNESS
CONTRAST
GAMMA
To adjust the brightness,
contrast and gamma of the
screen
PICTURE
PRESET
6500K
9300K
To customize the color of
the screen
COLOR
RED
GREEN
BLUE
HORIZONTAL
VERTICAL
CLOCK
To adjust the position of the
screen
POSITION
To improve the clarity and
stability of the screen
TRACKING
PHASE
LANGUAGE
SETUP
AUDIO
To customize the screen
status for a user's operating
environment
OSD
HORIZONTAL
POSITION VERTICAL
WHITE BALANCE
POWER INDICATOR
FACTORY RESET
To adjust the audio function.
VOLUME
: Adjustable
NOTE
The order of icons may differ depending on the model (A10~A13).
A10
On Screen Display(OSD) Selection and Adjustment
You were introduced to the procedure of selecting and adjusting an item
using the OSD system. Listed below are the icons, icon names, and icon
descriptions of the all items shown on the Menu.
Press the MENU Button, then the main menu of the OSD appears.
Menu Name
Icons
Sub-menus
NOTE
OSD (On Screen Display) menu languages on the monitor may differ from the manual.
A11
On Screen Display(OSD) Selection and Adjustment
Main menu
Sub menu
Description
PICTURE
To adjust the brightness of the screen.
To adjust the contrast of the screen.
BRIGHTNESS
CONTRAST
GAMMA
Set your own gamma value. : -50/0/50
On the monitor, high gamma values
display whitish images and low gamma
values display high contrast images.
COLOR
Select the screen color.
PRESET
• 6500K: Slightly reddish white.
• 9300K: Slightly bluish white.
Set your own red color levels.
Set your own green color levels.
Set your own blue color levels.
RED
GREEN
BLUE
POSITION
To move image left and right.
To move image up and down.
HORIZONTAL
VERTICAL
TRACKING
CLOCK
PHASE
To minimize any vertical bars or
stripes visible on the screen
background.The horizontal screen
size will also change.
To adjust the focus of the display.
This item allows you to remove any
horizontal noise and clear or
sharpen the image of characters.
A12
On Screen Display(OSD) Selection and Adjustment
Main menu
Sub menu
Description
SETUP
To choose the language in which the
control names are displayed.
LANGUAGE
OSD
To adjust position of the OSD window
on the screen.
POSITION
If the output of the video card is different
the required specifications, the color
level may deteriorate due to video
signal distortion. Using this function, the
signal level is adjusted to fit into the
standard output level of the video card
in order to provide the optimal image.
Activate this function when white and
black colors are present in the screen.
WHITE
BALANCE
Use this function to set the power
indicator on the front side of the monitor
to ON or OFF.
POWER
INDICATOR
If you set OFF, it will go off.
If you set ON at any time, the power
indicator will automatically be turned on.
FACTORY
RESET
Restore all factory default settings except
"LANGUAGE."
Press the
button to reset immediately.
If this does not improve the screen image, restore the factory default settings.
If necessary, perform the white balance function again. This function will be enabled only when
the input signal is an analog signal.
A13
Troubleshooting
Check the following before calling for service.
No image appears
Is the power cord of the
display connected?
Check and see if the power cord is connected
properly to the power outlet.
Is the power indicator
light on?
Touch the Power button.
Is the power on and the
power indicator blue or
green?
Adjust the brightness and the contrast.
Is the power indicator
amber?
If the display is in power saving mode, try moving
the mouse or pressing any key on the keyboard
to bring up the screen.
Try to turn on the PC.
This message appears when the signal from the
PC (video card) is out of horizontal or vertical
frequency range of the display. See the
'Specifications' section of this manual and
configure your display again.
Do you see an "OUT
OF RANGE" message
on the screen?
This message appears when the signal cable
between your PC and your display is not
connected. Check the signal cable and try again.
Do you see a "CHECK
SIGNAL CABLE"
message on the
screen?
Do you see a "OSD LOCKED" message on the screen?
Do you see “OSD
LOCKED” when you
push MENU button?
You can secure the current control settings,
so that they cannot be inadvertently
changed. You can unlock the OSD controls
at any time by pushing the MENU button for
serveral seconds: the message
“OSD UNLOCKED” will appear.
A14
Troubleshooting
Display image is incorrect
Display Position is
incorrect.
Press the AUTO/SET button to automatically adjust
your display image to the ideal setting.
If the results are unsatisfactory, adjust the image
position using the H position and V position icon
in the on screen display.
Check Control Panel --> Display --> Settings and
see if the frequency or the resolution were changed.
If yes, readjust the video card to the recommend
resolution.
On the screen
background, vertical
bars or stripes are
visible.
Press the AUTO/SET button to automatically adjust
your display image to the ideal setting.
If the results are unsatisfactory, decrease the
vertical bars or stripes using the CLOCK icon in the
on screen display.
Any horizontal noise
appearing in any
image or characters
are not clearly
Press the AUTO/SET button to automatically adjust
your display image to the ideal setting.
If the results are unsatisfactory, decrease the
horizontal bars using the PHASE icon in the on
screen display.
portrayed.
Check Control Panel --> Display --> Settings and
adjust the display to the recommended resolution or
adjust the display image to the ideal setting. Set the
color setting higher than 24 bits (true color).
The screen color is
mono or abnormal.
Check if the signal cable is properly connected and
use a screwdriver to fasten if necessary.
Make sure the video card is properly inserted in the
slot.
Set the color setting higher than 24 bits (true color)
at Control Panel - Settings.
The screen blinks.
Check if the screen is set to interlace mode and
if yes, change it to the recommend resolution.
Make sure the power voltage is high enough, It has
to be higher than AC100-240V 50/60Hz.
A15
Troubleshooting
Have you installed the display driver?
Have you installed the
display driver?
Be sure to install the display driver from the
display driver CD (or diskette) that comes with
your display. Or, you can also download the
Do you see an
Make sure to check if the video card supports
Plug&Play function.
"Unrecognized monitor,
Plug&Play (VESA DDC)
monitor found"
message?
Audio function
No sound.
Check if the audio cable is correctly connected.
Check the volume level.
Sound level is too low.
Check the volume level.
A16
Specifications
17inch
Display
17 inches (43.2cm) Flat Panel Active matrix-TFT LCD
Anti-Glare coating
17 inches viewable
0.264 mm pixel pitch
Sync Input
Horizontal Freq.
Vertical Freq.
Input Form
30 - 83kHz (Automatic)
56 - 75Hz (Automatic)
Separate TTL, Positive/Negative
SOG (Sync On Green)
Video Input
Resolution
Signal Input
Input Form
Max
Recommend
DDC 2B
15 pin D-Sub Connector
RGB Analog (0.7Vp-p/75ohm)
VESA 1280 x 1024@75Hz
VESA 1280 x 1024@60Hz
Plug&Play
Audio
RMS Audio Output 1W+1W(R+L)
Input Sensitivity 0.7Vrms
Speaker Impedance 16Ω
On Mode
Sleep Mode
Off Mode
37W
1W
1W
Power
Consumption
:
≤
≤
Width
Height
Depth
38.95 cm / 15.33 inches
43.79 cm / 17.24 inches
23.20 cm / 9.13 inches
Dimensions
&Weight
(with tilt stand)
Net
5.28 kg (11.64 lbs)
Tilt Range
Tilt
3˚~25˚
345˚
Swivel
Power Input
AC 100-240V~ 50/60Hz 1.0A
Operating Conditions
Environmental
Conditions
Temperature 10˚C to 35 ˚C
Humidity
10 % to 80 % non-Condensing
Storage Conditions
Temperature -20˚C to 60 ˚C
Humidity
5 % to 95 % non-Condensing
Tilt Stand
Attached( O ), Detached (
)
Signal cable
Power cord
Attached( ), Detached ( O )
Wall-outlet type or PC-outlet type
NOTE
Information in this document is subject to change without notice.
A17
Specifications
19inch
Display
19 inches (48.18cm) Flat Panel Active matrix-TFT LCD
Anti-Glare coating
19 inches viewable
0.294 mm pixel pitch
Sync Input
Horizontal Freq.
Vertical Freq.
Input Form
30 - 83kHz (Automatic)
56 - 75Hz (Automatic)
Separate TTL, Positive/Negative
SOG (Sync On Green)
Video Input
Resolution
Signal Input
Input Form
Max
Recommend
DDC 2B
15 pin D-Sub Connector
RGB Analog (0.7Vp-p/75ohm)
VESA 1280 x 1024@75Hz
VESA 1280 x 1024@60Hz
Plug&Play
Audio
RMS Audio Output 1W+1W(R+L)
Input Sensitivity 0.7Vrms
Speaker Impedance 16Ω
On Mode
Sleep Mode
Off Mode
Width
Power
Consumption
42W
1W
1W
:
≤
≤
Dimensions
&Weight
(with tilt stand)
44.36 cm / 17.46 inches
47.56 cm / 18.72 inches
23.20 cm / 9.13 inches
Height
Depth
Net
5.98 kg (13.18 lbs)
Tilt Range
Tilt
3˚~25˚
345˚
Swivel
Power Input
AC 100-240V~ 50/60Hz 1.0A
Operating Conditions
Environmental
Conditions
Temperature 10˚C to 35 ˚C
Humidity
10 % to 80 % non-Condensing
Storage Conditions
Temperature -20˚C to 60 ˚C
Humidity
5 % to 95 % non-Condensing
Tilt Stand
Attached( O ), Detached (
)
Signal cable
Power cord
Attached( ), Detached ( O )
Wall-outlet type or PC-outlet type
NOTE
Information in this document is subject to change without notice.
A18
Specifications
Preset Modes (Resolution)
Display Modes (Resolution)
Horizontal Freq. (kHz)
Vertical Freq. (Hz)
1
2
3
4
5
6
7
8
9
10
11
*12
13
31.469
31.468
31.469
37.500
37.879
46.875
49.725
48.363
60.023
68.681
61.805
63.981
79.976
VGA
VGA
VGA
640 x 350
720 x 400
640 x 480
640 x 480
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1152 x 870
1152 x 900
1280 x 1024
1280 x 1024
70
70
60
75
60
75
75
60
75
75
65
60
75
VESA
VESA
VESA
MAC
VESA
VESA
MAC
VESA
VESA
VESA
*Recommend Mode
Indicator
Mode
LED Color
On Mode
Sleep Mode
Off Mode
Blue
Amber
Off
A19
How to Install the Rack wall mounting
This monitor meets VESA-compliant mounting interface pad
specifications.
1.
Separate the stand Cover using a screwdriver as shown in the
picture.
Stand Cover
2. Please the monitor on a piece of cloth or other soft surface with the
3. Sfreopnat rsaitdeetfhaecisntganddowbansweaursdi.ng a screwdriver as shown in the picture.
4. Install the VESA standrad wall mounting.
VESA wall mounting
Connected to another object
(stand type and wall-mounted
type. This monitor accepts a
VESA-compliant mounting
interface pad.-optional)
PC Audio
For further information, refer to
the VESA Wall Mounting
Instruction Guide.
Kensington Security Slot- optional
Connected to a locking
cable that can be purchased separately at most computer stores
A20
Digitally yours
|