User’s Guide
L226WT
L226WTX
L226WTQ
L226WTG
L226WTM
L226WTY
L226WTP
Make sure to read the Important Precautions before using the product.
Keep the User's Guide(CD) in an accessible place for future reference.
See the label attached on the product and give the information to your
dealer when you ask for service.
Important Precautions
On Installation
Do not allow anything to rest upon or roll over the power cord, and do not place the
display where the power cord is subject to damage.
Do not use this display near water such as near a bathtub, washbowl, kitchen sink,
laundry tub, in a wet basement, or near a swimming pool.
Displays are provided with ventilation openings in the cabinet to allow the release of
heat generated during operation. If these openings are blocked, built-up heat can
cause failures which may result in a fire hazard. Therefore, NEVER:
Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.
Place the display in a built-in enclosure unless proper ventilation is provided.
Cover the openings with cloth or other material.
Place the display near or over a radiator or heat source.
Main power breaker is the power cord and this breaking device must be located at
a location where it is easy to operate.
Do not rub or strike the Active Matrix LCD with anything hard as this may scratch,
mar, or damage the Active Matrix LCD permanently.
Do not press the LCD screen with your finger for a long time as this may cause
some afterimages.
Some dot defects may appear as Red, Green or Blue spots on the screen.
However, this will have no impact or effect on the display performance.
If possible, use the recommended resolution to obtain the best image quality for
your LCD display. If used under any mode except the recommended resolution,
some scaled or processed images may appear on the screen. However, this is
characteristic of the fixed-resolution LCD panel.
On Cleaning
Unplug the display before cleaning the face of the display screen.
Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display
screen because over-spraying may cause electrical shock.
On Repacking
Do not throw away the carton and packing materials. They make an ideal
container in which to transport the unit. When shipping the unit to another
location, repack it in its original material.
On Disposal
The fluorescent lamp used in this product contains a small amount of mercury.
Do not dispose of this product with general household waste.
Disposal of this product must be carried out in accordance to the regulations of
your local authority.
A2
Connecting the speakers
-
The feature is only for speaker models - L226WTM
Connecting the speaker
1. Place the monitor with its front facing downward on a soft cloth.
2. Insert the protruding hook of the speaker in the direction of the slot in the back of the product.
Slot
Hook
Audio DC-In
Cable
AUDIO IN
3. After setting up the speaker, connect the Audio DC-In Cable to the back of the product.
DC-OUT
A3
Connecting the Display
Before setting up the monitor, ensure that the power to the monitor, the computer
system, and other attached devices is turned off.
Connecting the stand
1
.
2.
Place the monitor with its front facing downward on a soft cloth.
Assemble the Stand Body into the product in the correct direction as shown in the picture.
Make sure you push it until you hear it “click”.
Hinge Body
Stand Body
3
.
4.
Assemble the Stand Base(Front, Rear) into the Stand Body in the correct direction.
Once assembled take the monitor up carefully and face the front side
Stand Body
Stand Base
Important
This illustration depicts the general model of connection. Your monitor may differ from
the items shown in the picture.
Do not carry the product upside down holding only the stand base. The product may
fall and get damaged or injure your foot.
A4
Connecting the Display
Disassembling the stand
Type. A
1. Put a cushion or soft cloth on aflat
2. Place the monitor face Down on
surface.
the cushion or soft cloth.
3. Pushing Latch inside, Take the stand base from stand body.
4. Separate the stand using a screwdriver as shown in the picture.
Note: Please keep the 4 screws in an accessible place for future use.
5. Pack up the product as shown in the picture.
A5
Connecting the Display
Disassembling the stand
Type. B
1. Put a cushion or soft cloth on aflat
2. Place the monitor face Down on
surface.
the cushion or soft cloth.
3. Change your hold on the product as it follows and turn the Stand Base in the arrow direction.
4. Pull out the Stand to remove.
5. Pushing Latch inside, Take the stand
6. Pack up the product as shown in the
base from stand body.
picture.
A6
Connecting the Display
Before setting up the monitor, ensure that the power to the monitor, the computer
system, and other attached devices is turned off.
Positioning your display
1. Adjust the position of the panel in various ways for maximum comfort.
Tilt Range : -5˚~20˚
20
Swivel : 355˚
Ergonomic
It is recommended that in order to maintain an ergonomic and comfortable viewing
position, the forward tilt angle of the monitor should not exceed 5 degrees.
A7
Connecting the Display
Using the Computer
1. Make sure to turn off the computer and product. Connect the cable as below sketch map
1
2
form
to
.
A
B
C
Connect DVI Cable
Connect Dsub Cable (PC)
Connect Dsub Cable (Mac)
Analog signal
D-sub
Digital signal
DVI
Power Cord
Wall-outlet type
PC
PC-outlet type
PC
DVI-D(This feature is not available in all countries.)
PC
MAC
Mac adapter
For Apple Macintosh use, a separate plug adapter is
needed to change the 15 pin high density (3 row) D-sub
VGA connector on the supplied cable to a 15 pin 2 row
connector.
2. Press
button on the front switch panel to turn the
power on. When monitor power is turned on, the
'Self Image Setting Function' is executed automatically.
(Only Analog Mode)
NOTE
‘ Self Image Setting Function’? This function provides the user with optimal display settings.When the user
connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual
input signals.
‘AUTO/SET’ Function? When you encounter problems such as blurry screen, blurred letters, screen flicker or tilted
screen while using the device or after changing screen resolution, press the AUTO/SET function button to improve
resolution.
A8
Using the speakers - The feature is only for speaker models - L226WTM
Side Jack
Headphone/Earphone Input
Rear
Connects to the *LINE OUT jack of the
PC sound card.
AUDIO
IN
Speaker Out
*Line Out
<Jack of the PC sound card>
A9
Control Panel Functions
Front Panel Controls
6
(-)
(+)
Control
Function
At the current display, Use 'ez Zooming' Key, then the display
resolution is transferred to the one step low resolution.
Use 'ez Zooming' Key one more, the display is back to the
original display.
ZOOMING
*Only One touch of ez-zoom, you can fine the best resolution
you want and it is possible to magnify the size of characters and
pictures for the old not having good eye sight, housewives not
dealing with computer well and children.
Recommend resolution are 1680 x 1050, 1440 x 900, 1280 x 1024, 1024 x 768, 800 x 600.
The setting method can differ by O/S or video card. In this case, Please ask to the
computer or the video card manufacturer.
Use this button to enter or exit the On Screen Display.
MENU Button
OSD LOCKED/UNLOCKED
This function allows you to lock the current control
settings, so that they cannot be inadvertently changed.
Press and hold the MENU button for several seconds.
The message "OSD LOCKED" should appear.
You can unlock the OSD controls at any time by pushing
the MENU button for several seconds. The message
"OSD UNLOCKED" should appear.
A10
Control Panel Functions
Control
Function
Use these buttons to select or adjust functions in the On
Screen Display.
-
+
Buttons
For more information, refer to page A18.
(
-)
(
+)
Use this button to make D-Sub or DVI connector active.
This feature is used when two computers are connected
to the display. The default setting is D-Sub.
(
SOURCE Hot key)
Use this button to enter a selection in the On Screen
Display.
AUTO/SET
Button
AUTO IMAGE ADJUSTMENT
When adjusting your display settings, always press
the AUTO/SET button before entering the On Screen
Display(OSD). This will automatically adjust your
display image to the ideal settings for the current
screen resolution size (display mode).
The best display mode is
22 inch monitor : 1680 x 1050
Power Button
Use this button to turn the display on or off.
This Indicator lights up blue when the display
operates normally(On Mode). If the display is in Sleep
Mode (Energy Saving), this indicator color changes
to amber.
Power Indicator
A11
On Screen Display (OSD) Control Adjustment
Screen Adjustment
Making adjustments to the image size, position and operating parameters of
the display is quick and easy with the On Screen Display Control system.
A short example is given below to familiarize you with the use of the controls.
The following section is an outline of the available adjustments and selections
you can make using the OSD.
NOTE
Allow the display to stabilize for at least 30 minutes before making image adjustments.
To make adjustments in the On Screen Display, follow these steps:
- +
- +
Press the MENU Button, then the main menu of the OSD appears.
To access a control, use the - or + Buttons. When the icon you want
becomes highlighted, press the AUTO/SET Button.
Use the - /+ Buttons to adjust the image to the desired level. Use the
AUTO/SET Button to select other sub-menu items.
Push the MENU Button once to return to the main menu to select another
function. Push the MENU Button twice to exit from the OSD.
A12
On Screen Display(OSD) Selection and Adjustment
The following table indicates all the On Screen Display control, adjustment,
and setting menus.
Main menu
Sub-menu
BRIGHTNESS
CONTRAST
GAMMA
A
D
Reference
PICTURE
To adjust the brightness,
contrast and gamma of the
screen
sRGB
To customize the color of
the screen
COLOR
PRESET
6500K
9300K
RED
GREEN
BLUE
To adjust the position of the
screen
HORIZONTAL
POSITION
VERTICAL
CLOCK
To improve the clarity and
stability of the screen
PHASE
TRACKING
SHARPNESS
LANGUAGE
SETUP
To customize the screen
status for a user's operating
environment
OSD
HORIZONTAL
POSITION VERTICAL
WHITE BALANCE
POWER INDICATOR
4:3 IN WIDE
FACTORY RESET
MOVIE / TEXT
FLATRON
F-ENGINE
To select or customize
desired image settings
USER
NORMAL
: Adjustable
A : Analog Input
D : Digital Input
NOTE
The order of icons may differ depending on the model (A13~A18).
A13
On Screen Display(OSD) Selection and Adjustment
You were introduced to the procedure of selecting and adjusting an item
using the OSD system. Listed below are the icons, icon names, and icon
descriptions of the all items shown on the Menu.
Press the MENU Button, then the main menu of the OSD appears.
P I C T U R E
Menu Name
Sub-menus
Icons
Button Tip
MENU
: Exit
: Adjust (Decrease/Increase)
: Enter
+
-
SET
: Select another sub-menu
NOTE
OSD (On Screen Display) menu languages on the monitor may differ from the manual.
A14
On Screen Display(OSD) Selection and Adjustment
Main menu
Sub menu
Description
PICTURE
P I C T U R E
To adjust the brightness of the screen.
To adjust the contrast of the screen.
BRIGHTNESS
CONTRAST
GAMMA
Set your own gamma value. : -50/0/50
On the monitor, high gamma values
display whitish images and low gamma
values display high contrast images.
MENU : Exit
: Decrease
: Increase
-
+
SET : Select another sub-menu
COLOR
C O L O R
• sRGB: Set the screen color to fit the
SRGB standard color
PRESET
specification.
• 6500K: Slightly reddish white.
• 9300K: Slightly bluish white.
Set your own red color levels.
Set your own green color levels.
Set your own blue color levels.
RED
GREEN
BLUE
MENU : Exit
: Decrease
: Increase
SET : Select another sub-menu
-
+
A15
On Screen Display(OSD) Selection and Adjustment
Main menu
Sub menu
Description
POSITION
P O S I T I O N
To move image left and right.
To move image up and down.
HORIZONTAL
VERTICAL
MENU : Exit
: Decrease
: Increase
-
+
SET : Select another sub-menu
TRACKING
T R A C K I N G
CLOCK
To minimize any vertical bars or stripes
visible on the screen background.
The horizontal screen size will also
change.
PHASE
To adjust the focus of the display.
This item allows you to remove any
horizontal noise and clear or sharpen
the image of characters.
MENU : Exit
: Decrease
: Increase
SET : Select another sub-menu
-
SHARPNESS To adjust the clearness of the screen.
+
A16
On Screen Display(OSD) Selection and Adjustment
Main menu
Sub menu
Description
To choose the language in which the
control names are displayed.
LANGUAGE
SETUP
OSD
POSITION
To adjust position of the OSD window
on the screen.
S E T U P
WHITE
BALANCE
If the output of the video card is different
the required specifications, the color level
may deteriorate due to video signal
distortion. Using this function, the signal
level is adjusted to fit into the standard
output level of the video card in order to
provide the optimal image.
Activate this function when white and
black colors are present in the screen.
S E T U P
Use this function to set the power
indicator on the front side of the monitor
to ON or OFF.
POWER
INDICATOR
If you set OFF, it will go off.
If you set ON at any time, the power
indicator will automatically be turned on.
4:3 IN WIDE
To select the image size of the screen.
MENU : Exit
: Adjust
: Adjust
-
+
SET : Select another
sub-menu
WIDE
4:3
❈ 4:3 : Depending on the input video signal ratio,
it is automatically changed to an optimized screen
ratio. (The 1280X1024 input signal is changed
to 5:4 ratio and 1024X768 to 4:3.)
Resolution
Screen ratio
1280x1024
1152x864
1024x768
800x600
640x480
720x480
5 : 4
4 : 3
4 : 3
4 : 3
4 : 3
3 : 2
The input signal which the 4:3 IN WIDE does not support '4:3'
is the following.
-
The 22 inch monitor is 720x400,1280x768,1360x768,1440x900,
1680x1050.
FACTORY
RESET
Restore all factory default settings except
"LANGUAGE."
Press the
button to reset immediately.
-
If this does not improve the screen image, restore the factory default settings.
If necessary, perform the white balance function again. This function will be enabled only when
the input signal is an analog signal.
A17
On Screen Display(OSD) Selection and Adjustment
(
-)
The OSD screen will appear when you touch the
on the left side of the monitor.
Menu Name
button
Icons
Sub-menu Name
FLATRON F-ENGINE
Screen when applied Screen when not applied
When you execute F-ENGINE, two tones will appear
on the screen as shown. The applied screen will
appear on the left side, whereas the non-applied
screen will appear on the right side.Touch the SET
button to use the adjusted screen.
Main menu
Sub menu
Description
MOVIE This feature lets you easily select the best desired
TEXT image condition optimized to the environment
(ambient illumination, image types etc).
MOVIE: For animation images in videos or movies
TEXT: For text images (Word processing etc.)
MENU : Exit
+
-
,
: Move
SET : Select
USER User
You can manually adjust brightness, ACE or RCM.
You can save or restore the adjusted value even
when using a different environment.
To adjust the USER sub-menu function,
Press the SET Button
...
(Brightness): Adjusts screen brightness.
...
ACE(Adaptive Clarity Enhancer): Selects the clarity mode.
...
RCM(Real Color Management): Selects the color mode.
0
Not applied
1
Green enhance
2
Flesh tone
3
Color Enhance
SAVE
Select the
sub-menu using the SET button
MENU : Exit
and save the YES value using the buttons.
: Decrease
-
+
: Increase
SET : Select another sub-menu
NORMAL
This is under normal operating conditions.
A18
Troubleshooting
Check the following before calling for service.
No image appears
G Is the power cord of the
•
•
•
Check and see if the power cord is connected
properly to the power outlet.
display connected?
G Is the power indicator
Press the Power button.
light on?
Adjust the brightness and the contrast.
G Is the power on and the
power indicator blue or
green?
G Is the power indicator
•
If the display is in power saving mode, try moving
the mouse or pressing any key on the keyboard to
bring up the screen.
amber?
• Try to turn on the PC
.
•
•
This message appears when the signal from the
G Do you see an "OUT OF
RANGE" message on
the screen?
PC (video card) is out of horizontal or vertical
frequency range of the display. See the
'Specifications' section of this manual and
configure your display again.
This message appears when the signal cable
between your PC and your display is not
connected. Check the signal cable and try again.
G Do you see a "CHECK
SIGNAL CABLE"
message on the
screen?
Do you see a "OSD LOCKED" message on the screen?
G
Do you see “OSD
LOCKED” when you
push MENU button?
• You can secure the current control settings,
so that they cannot be inadvertently changed.
You can unlock the OSD controls at any time
by pushing the MENU button for several
seconds: the message
“OSD UNLOCKED” will appear.
A19
Troubleshooting
Display image is incorrect
G Display Position is
•
Press the AUTO/SET button to automatically
adjust your display image to the ideal setting.
If the results are unsatisfactory, adjust the image
position using the H position and V position icon
in the on screen display.
incorrect.
•
Press the AUTO/SET button to automatically
adjust your display image to the ideal setting.
If the results are unsatisfactory, decrease the
vertical bars or stripes using the CLOCK icon in
the on screen display.
G On the screen
background, vertical
bars or stripes are
visible.
•
•
Press the AUTO/SET button to automatically
adjust your display image to the ideal setting.
If the results are unsatisfactory, decrease the
horizontal bars using the PHASE icon in the on
screen display.
Check Control Panel --> Display --> Settings
and adjust the display to the recommended
resolution or adjust the display image to the ideal
setting. Set the color setting higher than 24 bits
(true color).
G Any horizontal noise
appearing in any
image or characters
are not clearly
portrayed.
Important
Check Control Panel --> Display --> Settings and see if the frequency or the
resolution were changed. If yes, readjust the video card to the recommend
resolution.
Reasons for Recommending Optimal Resolution : The aspect ratio is 16:10.
If the input resolution is not 16:10 (for instance, 16:9, 5:4, 4:3), you might encounter
problems such as blurred letters, blurry screen, cut-off screen display or tilted screen.
The setting method can differ by computer and O/S (Operation System),
and resolution mentioned above may not be supported by the video card
performance. In this case, please ask to the computer or the video card
manufacturer
.
A20
Troubleshooting
Display image is incorrect
G The screen color is
•
•
•
Check if the signal cable is properly connected
and use a screwdriver to fasten if necessary.
Make sure the video card is properly inserted in
the slot.
Set the color setting higher than 24 bits (true color)
at Control Panel - Settings.
mono or abnormal.
G The screen blinks.
•
Check if the screen is set to interlace mode and if
yes, change it to the recommend resolution.
Have you installed the display driver?
G
Have you installed the
display driver?
•
Be sure to install the display driver from the display
driver CD (or diskette) that comes with your
display. Or, you can also download the driver from
•
Make sure to check if the video card supports
Plug&Play function.
G
Do you see an
"Unrecognized monitor,
Plug&Play (VESA DDC)
monitor found"
message?
A21
Specifications
L226WT/L226WTX/L226WTQ/L226WTG/L226WTY/L226WTP
Display
22 inches (55.868 cm) Flat Panel Active matrix-TFT LCD
Anti-Glare coating (L226WT/L226WTX/L226WTQ/L226WTY/
L226WTP), Glare coating(L226WTG)
22 inches viewable
0.282*0.282 mm pixel pitch
Sync Input
Horizontal Freq. Analog : 28 - 83 kHz (Automatic)
Digital : 28 - 83 kHz (Automatic)
Vertical Freq.
Input Form
56 - 75 Hz (Automatic)
Separate TTL, Positive/Negative
SOG (Sync On Green)
Digital
Video Input
Signal Input
15 pin D-Sub Connector
DVI - D connector (Digital)
Input Form
Max
RGB Analog (0.7 Vp-p/ 75 ohm), Digital
Analog : VESA 1680 x 1050 @ 60 Hz
Digital : VESA 1680 x 1050 @ 60 Hz
VESA 1680 x 1050 @60 Hz
Resolution
Plug&Play
Recommend
DDC 2B
Power
Consumption
:
≤
≤
40W(Typ.)
1 W
1 W
On Mode
Sleep Mode
Off Mode
Dimensions
&Weight
With Stand
Without Stand
Width 50.17 cm / 19.75 inches 50.17 cm / 19.75 inches
Height 42.35 cm / 16.67 inches 33.74 cm / 13.28 inches
Depth 23.39 cm / 9.21 inches
5.95 cm / 2.34 inches
5.65 kg (12.56 lbs)
-5˚~20˚
Net
Tilt
Tilt Range
Power Input
AC 100-240V~ 50/60Hz 1.0A
Operating Conditions
Environmental
Conditions
Temperature 10˚C to 35 ˚C
Humidity
10 % to 80 % non-Condensing
Storage Conditions
Temperature -20˚C to 60 ˚C
Humidity
5 % to 90 % non-Condensing
Stand Base
Power cord
Attached ( ), Detached ( O )
Wall-outlet type or PC-outlet type
NOTE
Information in this document is subject to change without notice.
A22
Specifications
L226WTM
22 inches (55.868 cm) Flat Panel Active matrix-TFT LCD
Display
Anti-Glare coating
22 inches viewable
0.282*0.282 mm pixel pitch
Sync Input
Video Input
Horizontal Freq.
Analog : 28 - 83 kHz (Automatic)
Digital : 28 - 83 kHz (Automatic)
56 - 75 Hz (Automatic)
Separate TTL, Positive/Negative
SOG (Sync On Green),Digital
15 pin D-Sub Connector
Vertical Freq.
Input Form
Signal Input
DVI - D connector (Digital)
Input Form
Max
RGB Analog (0.7 Vp-p/ 75 ohm), Digital
Analog : VESA 1680 x 1050 @60 Hz
Digital : VESA 1680 x 1050 @60 Hz
VESA 1680 x 1050 @60 Hz
Resolution
Plug&Play
Recommend
DDC 2B
:
≤
≤
40W(Typ.)
1 W
1 W
Power
Consumption
(without speaker)
On Mode
Sleep Mode
Off Mode
With Stand
Without Stand
Dimensions
&Weight
Width 50.17 cm / 19.75 inches 50.17 cm / 19.75 inches
Height 42.35 cm / 16.67 inches 37.14 cm / 14.62 inches
Depth 23.39 cm / 9.21 inches
5.95 cm / 2.34 inches
Net
5.85 kg (13 lbs)
Tilt Range
Tilt
-5˚~20˚
AC 100-240V~ 50/60Hz 1.0A
Power Input
Operating Conditions
Environmental
Conditions
Temperature 10˚C to 35 ˚C
Humidity
10 % to 80 % non-Condensing
Storage Conditions
Temperature -20˚C to 60 ˚C
Humidity
5 % to 90 % non-Condensing
Stand Base
Attached ( ), Detached ( O )
Wall-outlet type or PC-outlet type
Power cord
Audio
RMS Audio Output
Input Sensitivity
1W+1W(R+L)
0.7Vrms
16Ω
Speaker Impedance
NOTE
Information in this document is subject to change without notice.
A23
Specifications
Preset Modes (Resolution)
Display Modes (Resolution)
Horizontal Freq. (kHz)
Vertical Freq. (Hz)
1
2
3
4
5
6
7
8
9
720 x 400
640 x 480
640 x 480
800 x 600
800 x 600
1024 x 768
1024 x 768
1152 x 864
1280 x 1024
1280 x 1024
1680 x 1050
1680 x 1050
31.468
31.469
37.500
37.879
46.875
48.363
60.123
67.500
63.981
79.976
64.674
65.290
70
60
75
60
75
60
75
75
60
75
60
60
10
11
*12
*Recommend Mode
Indicator
LED Color
MODE
blue
amber
Off
On Mode
Sleep Mode
Off Mode
A24
Installing the Wall mount plate
This monitor satisfies the specifications of the Wall mount plate or
the interchange device.
1. Place the monitor with its front facing downward on a soft cloth.
2. Separate the stand using a screwdriver as shown in the picture.
3. Install the Wall mount plate.
Wall mount plate(Separate purchase)
This is stand-type or wall mount type and is
connectable with Wall mount plate.
Please refer to the installation guide for more
details, which is provided when Wall mount plate is
purchased.
Kensington Security Slot
Connected to a locking
cable that can be purchased
separately at most
computer stores.
A25
Digitally yours
|