Intel SBC 776 User Manual

SBC-776  
Full-sized Intel FC-370 Pentium III CPU  
Card with Intel 815E chipset, Dual LAN,  
Audio, SCSI, LCD & 4 USB.  
Acknowledgments  
All other product names or trademarks are properties of their  
respective owners.  
AMD is a trademark of Advanced Micro Devices, Inc.  
AMI is a trademark of American Megatrends, Inc.  
Award is a trademark of Award Software International, Inc.  
IBM, PC/AT, PS/2, and VGA are trademarks of International  
Business Machines Corporation.  
Intel and Pentium III are trademarks of Intel Corporation.  
Microsoft Windows® is a registered trademark of Microsoft Corp.  
SMC is a trademark of Standard Microsystems Corporation.RTL is  
a trademark of Realtek Semi-Conductor Co., Ltd.  
C&T is a trademark of Chips and Technologies, Inc.  
UMC is a trademark of United Microelectronics Corporation.  
ITE is a trademark of Integrated Technology Express, Inc.  
SiS is a trademark of Silicon Integrated Systems Corp.  
VIA is a trademark of VIA Technology, Inc.  
A Message to the Customer  
AAEON Customer Services  
Each and every AAEON product is built to the most exacting  
specifications to ensure reliable performance in the harsh and  
demanding conditions typical of industrial environments. Whether  
your new AAEON equipment is destined for the laboratory or the  
factory floor, you can be assured that your product will provide the  
reliability and ease of operation for which the name AAEON has  
come to be known.  
Your satisfaction is our primary concern. Here is a guide to  
AAEON's customer services. To ensure you get the full benefit of  
our services, please follow the instructions below carefully.  
Technical Support  
We want you to get the maximum performance from your products.  
So if you run into technical difficulties, we are here to help. For the  
most frequently asked questions, you can easily find answers in  
your product documentation. These answers are normally a lot  
more detailed than the ones we can give over the phone.  
So please consult this manual first. If you still cannot find the  
answer, gather all the information or questions that apply to your  
problem, and with the product close at hand, call your dealer. Our  
dealers are well trained and ready to give you the support you need  
to get the most from your AAEON products. In fact, most problems  
reported are minor and are able to be easily solved over the phone.  
In addition, free technical support is available from AAEON  
engineers every business day. We are always ready to give advice  
on application requirements or specific information on the installa-  
tion and operation of any of our products.  
Product Warranty  
AAEON warrants to you, the original purchaser, that each of its  
products will be free from defects in materials and workmanship for  
two years from the date of shipment.  
This warranty does not apply to any products which have been  
repaired or altered by persons other than repair personnel autho-  
rized by AAEON, or which have been subject to misuse, abuse,  
accident or improper installation. AAEON assumes no liability  
under the terms of this warranty as a consequence of such events.  
Because of AAEON's high quality-control standards and rigorous  
testing, most of our customers never need to use our repair service.  
If an AAEON product is defective, it will be repaired or replaced at  
no charge during the warranty period. For out-of-warranty repairs,  
you will be billed according to the cost of replacement materials,  
service time, and freight. Please consult your dealer for more  
details.  
If you think you have a defective product, follow these steps:  
1. Collect all the information about the problem encountered. (For  
example, CPU type and speed, AAEON products used, other  
hardware and software used, etc.) Note anything abnormal and  
list any on-screen messages you get when the problem occurs.  
2. Call your dealer and describe the problem. Please have your  
manual, product, and any helpful information readily available.  
3. If your product is diagnosed as defective, obtain an RMA  
(return material authorization) number from your dealer. This  
allows us to process your return more quickly.  
4. Carefully pack the defective product, a fully-completed Repair  
and Replacement Order Card and a photocopy proof of pur-  
chase date (such as your sales receipt) in a shippable container.  
A product returned without proof of the purchase date is not  
eligible for warranty service.  
5. Write the RMA number visibly on the outside of the package  
and ship it prepaid to your dealer.  
Packing list  
Before you begin installing your card, please make sure that the  
following materials have been shipped:  
• 1 SBC-776 Half- size Single Board Computer Card  
• 1 Quick Installation Guide  
• 1 Support CD contains the followings:  
-- User's Manual (this manual in PDF file)  
-- Ethernet driver and utilities  
-- VGA driver and utilities  
-- Audio driver and utilities  
• 1 floppy disk drive interface cable (34-pin, pitch 2.0mm)  
• 1 IDE hard disk drive cable (40-pin, pitch 2.54mm)  
• 1 parallel port (26-25-pin, pitch 2.0mm) and serial port (10-9 pin,  
pitch 2.0mm) adapter kit.  
• 1 bag of screws and miscellaneous parts  
If any of these items are missing or damaged, contact your distribu-  
tor or sales representative immediately.  
Notice  
Dear Customer,  
Thank you for purchasing the SBC-776 board. This user's  
manual is designed to help you to get the most out of the SBC-776,  
please read it thoroughly before you install and use the board. The  
product that you have purchased comes with an two-year limited  
warranty, but AAEON will not be responsible for misuse of the  
product. Therefore, we strongly urge you to first read the manual  
before using the product.  
To receive the latest version of the user manual, please visit our  
Web site at:  
Http:\\WWW.AAEON.COM  
http://www.aaeon.com  
Contents  
Chapter 1: General Information.........................................1  
Introduction.......................................................2  
Features.................................................................................... 3  
Specifications ........................................................................... 4  
Board layout ............................................................................. 7  
Board dimensions ..................................................................... 8  
Chapter 2: Installation .......................................................... 9  
Safety Precautions...........................................................10  
Removing the CPU..................................................10  
Installing the CPU............................................................... 11  
Installing SDRAM...................................................12  
Jumpers..............................................................13  
Connectors ..............................................................................14  
Locating Jumpers and Connectors............................................15  
Mechanical Drawing................................................17  
VGA or AGP VGA Header Select (JP1).................................19  
Clear CMOS (JP2) .................................................................19  
Watchdog Timer (JP3) ............................................................20  
COM2 RS-232/422/485 Setting (JP4)......................................21  
DiskOnChip Address Select (JP5).................................... ..22  
Function Select Header (JP6) .................................................24  
CPU/DIMM Speed Select Header (JP7) ...............................25  
LCD Panel's Voltage Setting (JP8) ....................................... 27  
COM2 RS-232/422/485 Setting (JP4) .....................................28  
LCD or VGA Enable Header (JP10) .....................................29  
VGA Connector (CN6)...........................................................29  
IDE Hard Drive Connector (CN7) .........................................30  
USB Connector (CN9, CN10)...............................31  
Audio Connector (CN11) ........................................................32  
Floppy Drive Connector (CN12).........................................33  
PS/2 Keyboard and Mouse Connector(CN13) .......................33  
Parallel Port Connector (CN14)..............................................34  
COM1 & COM2 Serial Port (CN15, CN16)..........................35  
SCSI Connector (CN21) .........................................................36  
100Base-Tx Fast Ethernet Connector (CN22, CN20)............37  
ATX Power Connector (CN23)..............................38  
Speaker/BuzzerConnector (CN24)..........................38  
Fan Power Connector (CN25, CN26, CN27)...........................39  
LCD Backlight Power Connector (CN28)...............40  
TFT LCD Panel Connector (CN29)......................40  
PS/2 Keyboard Header (CN31)............................41  
PS/2 Mouse Header (CN32)................................41  
Chapter 3: Award BIOS Setup...........................................42  
Starting setup..................................................................43  
Setup keys.......................................................................44  
Getting help ......................................................................... 45  
Main setup menu .....................................................................46  
Standard CMOS setup ............................................................48  
Advanced BIOS features........................................................53  
Advanced CHIPSET features ................................................58  
Integrated Peripherals...............................................61  
Power management setup .......................................................67  
PNP/PCI congfiguration setup................................................72  
PC Health Status......................................................74  
Frequency/Voltage Control........................................75  
Load Fail-Safe Defaults............................................76  
Load Optimized Defaults..........................................77  
Set Supervisor Password.......................................78  
Set User Password...............................................79  
Save and Exit Setup............................................80  
Exit  
&
Save......................................................81  
Chapter 4: Drivers and Utilities .......................................82  
Installing Drivers Attention Notice....................................83  
Software Installation Utilities........................................85  
Intel 82562ET LAN Driver............................................86  
Advansys 38C0800 SCSI Driver............................................89  
Intel 82559ER LAN Driver...........................................91  
VGA Driver...............................................................93  
Ultra ATA Storage Driver................................................94  
Audio  
Driver............................................................95  
1
General  
I n fo r m a t io n  
This chapter gives background  
information of the mainboard.  
Sections Include:  
• Board Specifications  
• Layout and Dimensions  
Introduction  
The SBC-776 is an all-in-one Single Board Computer (SBC) capable  
of handling the Intel Celeron 300~766MHz (with system bus  
frequencies of 66MHz) and Pentium III 500~850 MHz (with system  
bus frequencies of 100MHz). Reliability, performance, flexibility are  
essential qualities for SBC's and SBC-776 offers all of these.  
Onboard is the versatile Intel 815E chipset, controlling LAN, LCD,  
and AUDIO. The VGA has a display memory size of 4 MB, with  
resolutions up to 1024 x 768 at 256K. Ethernet connections can be  
easily carried out through two RJ-45 connectors.  
This full-sized SBC supports M-Systems DiskOnChip 2000 family  
of flash disk products that are small, plug and play, solid state disks  
in a standard 32-pin DIP package with capabilities ranging from  
8MB to 288MB. There are also three 168-pin DIMM sockets  
providing a maximum of 512MB. A compact flash connector is  
provided on the solder side of the board.  
The additional Advansys ASC38C0800, Ultra II Wide SCSI coordi-  
nates up to 15 devices that are simultaneously connected to your  
mainboard. Connection with the onboard chipset is made through  
a 68-pin SCSI connector.  
SBC-776 supports two IDE devices, two floppy disks, four USB  
ports, two serial ports that can be configured as COM1, COM2,  
COM3 and COM4. The single bidirectional parallel port can  
support SPP, ECP and EPP modes. The standard ATX power  
connector enables this full-sized SBC to be operated without any  
backplane if necessary.  
2
SBC-776 User Manual  
Features  
• Supports Intel Celeron /Pentium III FC-370 CPUs  
• High Speed AGP 2X for VGA function onboard  
(Intel 815E built in)  
• Two 10/100 Base-T Fast Ethernet (Intel 815 E built in and Intel 82559ER)  
• Supports H/W status monitoring  
• Integrated AC-97 2.1 SoundBlaster compatible PCI 3D Audio  
• Onboard Intel 815E controller supports 18/36-bit TFT panel  
• Supports Compact Flash Memory  
• Four USB ports onboard  
• Two COM ports onboard  
• Ultra II Wide SCSI interface onboard  
• Supports DiskOnChip  
Chapter 1 General Information  
3
Specifications  
Standard LPX-size SBC functions  
CPU: FC-370 Pentium III (Coppermine), Celeron, and compatible CPUs  
(With system bus frequencies of 66/100/133MHz).  
CPU socket: Intel Socket 370  
Bus interface: PICMG Compliant  
BIOS: Award 4 MB Flash BIOS  
Chipset: Intel 815E  
I/O chipset: Winbond W83627HF. Fully 16-bit I/O decoded  
ISA bus interface: Winbond W83626 LPC to ISA bridge Full ISA bus  
function except master mode support  
Memory : Onboard three 168 pins DIMM socket supports up to  
512Mbytes SDRAM (PC-133 SDRAM supported).  
Enhanced IDE: Supports two IDE channel. Support Ultra DMA/ 100  
mode with data transfer rate of 100MB/sec.  
FDD interface: Supports two floppy disk drives, 5.25" (360KB and  
1.2MB) and/or 3.5" (720KB, 1.44MB, and 2.88MB).  
Parallel port: One bi-directional parallel ports. Supports SPP, ECP, and  
EPP modes.  
Serial port: One RS-232 and one RS-232/422/485 serial port. Ports can be  
configured as COM1, COM2, COM3, COM4, or disabled individually  
and of which one and be configured as RS-232/422/485 (COM2).  
(16C550 equivalent).  
KB/Mouse connector : 6-pin mini-DIN connector supports PC/AT  
keyboard and PS/2 mouse and wake on KBD function.  
USB connectors: 10-pin onboard connector supports four USB ports.  
Battery: Lithium battery for data retention  
Watchdog timer: Can generate a system reset, IRQ15, or NMI.  
Software selectable time-out interval (1 sec. ~ 255 min., 1 sec./step or  
1 min./step)  
DMA: 7 DMA channels (8237 equivalent)  
4
SBC-776 User Manual  
Interrupt: 15 interrupt levels (8259 equivalent)  
Power management: Supports ATX power supply. I/O peripheral  
support power saving and doze/standby/suspend modes. APM 1.2  
compliant.  
H/W status monitoring: Embedded in W83267HF supports power,  
supply voltages, and temperature monitoring.  
Flat Panel/CRT Interface  
Chipset: embedded In Intel 815E  
Chipset output VGA signal: AGP 4X  
Display memory: Share system memory 4MB SDRAM (Max)  
Display type: Supports non-interlaced CRT and up to 18/36 bit LCD (TFT,  
LCD, only). Can display both CRT and Flat Panel simultaneously.  
Resolution: Up to 1024 x 768 @ 256 K colors  
Audio Interface  
Chipset: Intel 815E  
Audio interface: One 14 pin header (2.00mm)  
Codec: ALC 200  
Ethernet Interface  
Chipset: Intel 815E embedded in ICH2 and Intel 82559ER  
Ethernet interface : 82559ER does not support WOL and AOL  
82562ET support WOL and do not support AOL  
82562EM support WOL and AOL. 776 offers 82559ER and 82562 ET on  
board.  
Compact Flash socket onboard  
• Compact flash connector onboard support type 2 CFD  
Chapter 1 General Information  
5
Ultra Wide II SCSI Interface  
Chipset: AdvanSys ASC38C0800  
Connector: 68-pin internal  
Termination: Auto termination  
SSD Interface  
• One 32-pin DIP socket supports M-Systems DiskOnChip 2000 series  
Mechanical and environmental  
Power supply voltage: ATX power supply  
Operating temperature: 32 to 140o F (0 to 60o C)  
Board size: 13.3"(L) x 4.8"(W) (338mm x 122mm)  
Weight: 1.2 lb. (0.3 Kg)  
6
SBC-776 User Manual  
Board Layout  
CN24  
JP7  
CN2  
CN3  
CN4  
JP10  
JP1  
CN7  
CN5  
CN12  
JP2  
JP8  
CN28  
CN29  
CN9  
CN30  
CN10  
7 7 F 3 - 9 8 A W  
n d b n o i  
W
JP5  
CN33  
JP9  
JP3  
JP4  
CN21  
CN11  
CN32  
Chapter 1 General Information  
7
Board Dimensions  
A
7 F - 3 9 8 7 W  
o b n n d i  
W
8
SBC-776 User Manual  
2
Installation  
This chapter describes how to set up the  
main board hardware, including instruc-  
tions on setting jumpers and connecting  
peripherals, switches, and indicators. Be  
sure to read all the safety precautions  
before you begin the installation proce-  
dure.  
SBC-776  
Safety precautions  
Warning! Always completely disconnect the power cord from  
your chassis whenever you are working on it. Do  
not make connections while the power is on  
because sensitive electronic components can be  
damaged by the sudden rush of power.Only  
experienced electronics personnel should open the  
PC chassis.  
Caution! Always ground yourself to remove any static charge  
before touching the CPU card. Modern electronic  
devices are very sensitive to static electric charges.  
Use a grounding wrist strap at all times. Place all  
electronic components on a static-dissipative surface  
or in a static-shielded bag when they are not in the  
chassis.  
Removing the CPU  
The SBC-776 all-in-one CPU module supports most Pentium III/  
Celeron or 586 CPUs. The system's performance depends on the  
CPU you choose. You can install or upgrade the CPU in the board's  
PGA socket by following the procedures outlined below. If your  
system has an existing CPU, you need to remove it before installing  
the new CPU.  
Removing a CPU  
1. Disconnect power from the chassis, and unplug all connections  
to the CPU card. Then, remove the CPU card from the chassis  
by following the instructions in the user's manual for your  
chassis.  
2. Lift the CPU out of the PGA socket. The old chip may be  
difficult to remove. You may find spray chip lubricant, designed  
for pin-grid-array (PGA) devices, and a chip puller helpful.  
These are available at electronics hobbyists' supply stores.  
1 0  
SBC-776 ManualBC-599/596  
Installing A CPU  
To install the CPU, follow the instructions that came with it. If no  
documentation was provided, the general procedures for installing  
a CPU are outlined below:  
1. Lubricate the pins on the CPU with lubricant for PGA devices.  
This makes the CPU slide in much easier and greatly reduces  
the chance of damaging the pins and other components.  
2. Carefully align the CPU so that it is parallel to the socket. Make  
sure that the notch on the corner of the CPU matches the notch  
on the inside of the socket.  
3. Gently push the CPU into the socket. There will probably be a  
small gap between the CPU and the socket even when it is fully  
seated. DO NOT USE EXCESSIVE FORCE!  
When you install a new CPU, you may have to adjust other  
settings on the board, such as CPU type, CPU clock, and PCI  
speed, to accommodate it. Make sure that the settings are correct  
for your CPU. Improper settings may damage the CPU.  
SBC-776 Chapter 2 11  
SBC-776  
Installing DRAM (DIMMs)  
System Memory  
The SBC-776 contains three sockets for 168-pin dual inline memory  
module (DIMM). The socket uses 3.3 V unbuffered synchronous  
DRAM (SDRAM). DIMM is available in capacities of 16, 32, 64, 128  
or 256 MB. The socket can be filled in the DIMM of any size,  
giving your SBC-776 single board computer between 16 and 512  
MB of memory.  
Supplementary information about DIMM  
SBC-776 can accept PC-133 SDRAM DIMM Module(with or  
without parity).  
Single-sided modules are typically 16 or 64 MB; double-sided  
modules are usually 32, 128 or 256 MB.  
Memory Installation Procedures  
To install DIMM, first make sure the two handles of the DIMM  
socket are in the "open" position. i.e. The handles remain outward.  
Slowly slide the DIMM module along the plastic guides on both  
ends of the socket. Then press the DIMM module right down into  
the socket, until you hear a click. This is when the two handles  
have automatically locked the memory module into the correct  
position of the DIMM socket. (See Figure below) To take away the  
memory module, just push both handles outward, and the memory  
module will be ejected by the mechanism in the socket.  
1 2  
SBC-776 ManualBC-599/596  
Jumpers  
Jumpers  
Function  
JP1  
JP2  
JP3  
JP4  
JP5  
JP6  
JP7  
JP8  
JP9  
JP10  
VGA or AGP VGA Select Header  
Clear CMOS Selection  
Watchdog Function Select  
RS-232/422/485 COM 2 Setting  
DiskOnChip Address Selection  
Function Select  
CPU/DIMM Speed Select  
LCD Panel's Voltage Setting  
RS-232/422/485 COM2 Setting  
LCD or VGA Enable Header  
SBC-776 Chapter 2 13  
SBC-776  
Connectors  
Connector  
Function  
CN2,3,4  
SDRAM Slot  
CN5  
AGP Slot  
CN6  
VGA Connector  
CN7  
Primary IDE Connector  
Compact Flash  
CN8  
CN9,10  
CN11  
CN12  
CN13  
CN14  
CN15  
CN16  
CN20,22  
CN21  
USB Dual Port Header  
Audio Connector  
Floppy Drive Connector  
PS/2 Keyboard and Mouse Connector  
Parallel Port Connector  
COM 1 Serial Port  
COM 2 Serial Port  
LAN RJ-45 Connector  
SCSI Connector  
CN23  
CN24  
ATX Power Supply  
Speaker/Buzzer  
CN25  
CN26  
CN27  
CN28  
CN29  
CN31  
CN32  
System FAN 1 Connector  
CPU Fan Connector  
System FAN 2 Connector  
LCD Backlight Power Connector  
TFT LCD Panel Connector  
PS/2 Keyboard Header  
PS/2 Mouse Header  
1 4  
SBC-776 ManualBC-599/596  
Locating Jumpers and Connectors  
CN24  
JP7  
CN2  
CN3  
CN4  
JP10  
JP1  
CN7  
CN5  
CN12  
JP2  
JP8  
CN28  
CN29  
CN9  
CN30  
CN10  
7 7 F 3 - 9 8 A W  
n d b n o i  
W
JP5  
CN33  
JP9  
JP3  
JP4  
CN21  
CN11  
CN32  
SBC-776 Chapter 2 15  
SBC-776  
Locating Jumpers and Connectors  
CN8  
1 6  
Mechanical Drawing  
A
7 F - 3 9 8 7 W  
o b n n d i  
W
SBC-776 Chapter 2 17  
SBC-776  
Mechanical Drawing  
1 8  
SBC-776 ManualBC-599/596  
VGA or AGP VGA Header Select (JP 1)  
Select AGP VGA  
1
3
2
4
5
6
7
8
9
11  
13  
10  
12  
14  
Select on board VGA  
1
3
2
4
5
6
7
8
9
11  
13  
10  
12  
14  
Clear CMOS (JP2)  
You can use JP2 to clear the CMOS data if necessary. To reset the  
CMOS data, place a jumper on JP2 for just a few seconds, then  
remove the jumper.  
Clear CMOS (J2P)  
Clear CMOS  
Protect*  
1 2 3  
1 2 3  
JP2  
*default  
SBC-776 Chapter 2 19  
SBC-776  
Watchdog Timer Function Select (JP3)  
The mainboard is equipped with a watchdog timer that resets the CPU  
or generates an interrupt if processing comes to a standstill for whatever  
reason. This feature ensures system reliability in industrial stand-alone  
and unmanned environments.  
Reset  
1
3
5
2
4
6
IRQ15  
1
2
3
5
4
6
NMI  
1
2
3
5
4
6
2 0  
SBC-776 ManualBC-599/596  
RS-232/ 422/ 485 COM 2 (JP4 & JP9) Setting  
The SBC-776 COM 2 serial port can be selected as RS-232/422/485 by  
setting JP4.  
*RS-232  
3 6 9 12  
2 4 6  
1 3 5  
1 4 7 10  
*RS-485  
3 6 9 12  
1 4 7 10  
2 4 6  
1 3 5  
*RS-422  
3 6 9 12  
2 4 6  
1 3 5  
1 4 7 10  
SBC-776 Chapter 2 21  
SBC-776  
DiskOnChip Address Selection (JP5)  
The DiskOnChip 2000 occupies an 8 Kbyte window in the upper  
memory address range of C800 to D400. You should ensure this  
does not conflict with any other device's memory address. JP5  
controls the memory address of the Flash Disk.  
*D400H  
1 3 5  
2 4 6  
*DC00H  
1 3 5  
2 4 6  
*CE00H  
1 3 5  
2 4 6  
*D000H  
1 3 5  
2 4 6  
2 2  
SBC-776 ManualBC-599/596  
*E000H  
1 3 5  
2 4 6  
*DOC Disable  
1 3 5  
2 4 6  
*D800H  
*C800H  
1 3 5  
2 4 6  
1 3 5  
2 4 6  
These addresses might conflict with the ROM BIOS of  
other  
peripheral boards, Please select the appropriate memory  
address to avoid memory conflicts.  
SBC-776 Chapter 2 23  
SBC-776  
Function Select Header (JP 6)  
Next you may want to install external switches to monitor and  
control the mainboard. These features are completely optional —  
install them only if you need them. The front panel connector (JP6)  
is an 16-pin male, dual in-line header and provides connections for  
a speaker, hard disk access indicator and an input switch for  
resetting the card.  
Speaker  
The mainboard can drive an 8external speaker at 0.5 watts. If  
there is no external speaker, the SBC-776 provides an onboard  
buzzer as an alternative.  
LED interfa ce  
The front panel LED indicator for hard disk access is an active low  
signal (24 mA sink rate).  
1
3
5
2
4
6
Power Button  
Reset Switch  
Suspend Switch  
Hard Disk LED  
7
8
9
11  
13  
10 Power LED  
12 Supend LED  
14 SCSI LED  
15  
16 Chassis Open Detected  
2 4  
SBC-776 ManualBC-599/596  
CPU/ DIMM Speed Select Header (JP 7)  
CPU/133  
DIMM/133  
1
3
5
7
2
4
6
8
CPU/133  
DIMM/100  
1
3
5
7
2
4
6
8
CPU/100  
DIMM/100  
1
3
5
7
2
4
6
8
CPU/66  
DIMM/100  
1
3
5
7
2
4
6
8
SBC-776 Chapter 2 25  
SBC-776  
Auto Detect  
Default  
1
3
5
7
2
4
6
8
2 6  
SBC-776 ManualBC-599/596  
LCD Panel’s Voltage Setting (JP 8)  
*LCD Panel power: +5V; Backlight power: +5V  
1 3 5  
2 4 6  
*LCD Panel power: +5V; Backlight power: +12V  
1 3 5  
2 4 6  
*LCD Panel power: +3.3V; Backlight power: +5V  
1 3 5  
2 4 6  
*LCD Panel power: +3.3V; Backlight power: +12V  
1 3 5  
2 4 6  
SBC-776 Chapter 2 27  
SBC-776  
LCD or VGA Ena ble Hea der (JP10)  
* Default VGA  
Dual Display  
1 3 5  
1
3
5
6
VGA Enable  
VGA/LCD Enable  
LCD 1PIXS/CLK  
LCD 2PIXS/CLK  
2 4  
2
4
6
VGA conne ctor (CN6)  
The mainboard's PCI SVGA interface can drive conventional CRT  
displays and is capable of driving a wide range of flat panel  
displays, including electroluminescent (EL), gas plasma, passive  
LCD, and active LCD displays. The board has two connectors to  
support these displays, one for standard CRT VGA monitors and  
one for flat panel displays.  
VGA display connector (CN6)  
CN6 is a 15-pin, dual-in-line header used for conventional CRT  
displays. A simple one-to-one adapter can be used to match CN6 to  
a standard 15-pin D-SUB connector commonly used for VGA.  
VGA display connector (CN6)  
Pin  
1
Signal  
RED  
Pin  
9
Signal  
VCC  
2
GREEN  
10  
GND  
3
4
5
6
7
8
BLUE  
N/C  
11  
12  
13  
14  
15  
16  
N/C  
DDDA  
H-SYNC  
V-SYNC  
DDCK  
N/C  
GND  
GND  
GND  
GND  
2 8  
SBC-776 ManualBC-599/596  
I DE Ha rd Drive Con n e ct or (CN7 )  
IDE hard drive connector (CN7)  
Pin  
Signal  
Pin  
Signal  
1
IDE RESET  
2
GND  
3
DATA 7  
4
DATA 8  
DATA 9  
DATA 10  
DATA 11  
DATA 12  
DATA 13  
DATA 14  
DATA 15  
N/C  
5
DATA 6  
6
7
DATA 5  
8
9
DATA 4  
10  
12  
14  
16  
18  
20  
22  
24  
26  
11  
13  
15  
17  
19  
21  
23  
25  
27  
29  
31  
33  
35  
37  
39  
41  
43  
DATA 3  
DATA 2  
DATA 1  
DATA 0  
SIGNAL GND  
IDEPDREQR  
IO WRITE  
IO READ  
GND  
GND  
GND  
IO CHANNEL READY 28  
GND  
IDEPDACKX  
IRQ14  
30  
32  
34  
36  
38  
40  
42  
44  
GND  
IOCS16  
P66DET  
ADDR 2  
HARD DISK SELECT 1  
MGND  
ADDR 1  
ADDR 0  
HARD DISK SELECT 0  
IDE ACTIVE  
VCC  
VCC  
GND  
N/C  
SBC-776 Chapter 2 29  
SBC-776  
USB connector (CN9, CN10)  
The SBC-776 provides two USB (Universal Serial Bus) interfaces,  
which give complete plug and play, hot attach/detach for up to 127  
external devices. The USB interfaces comply with USB specifica-  
tion Rev. 1.0, and can be disabled in the system BIOS setup.  
USB connector (CN9)  
Pin  
Function  
Pin  
Function  
1
VCC  
2
GND  
3
5
7
9
USBD0-  
4
6
GND  
UDBD0+  
GND  
USBD1+  
8
USBD1-  
GND  
10  
VCC  
USB connector (CN10)  
Pin  
Function  
Pin  
Function  
1
VCC  
2
GND  
3
5
7
9
USBD2-  
4
6
GND  
USBD2+  
GND  
USBD3+  
USBD3-  
VCC  
8
GND  
10  
3 0  
SBC-776 ManualBC-599/596  
Audio Conne ctor (CN11)  
On board SBC-776, there is a 14-pin header for audio capability.  
The pin definition is provided below.  
Audio connector (CN 11)  
Pin  
1
3
Signal  
MIC IN  
GND  
Pin  
2
4
Signal  
MIC VCC  
CD IN GND  
CD IN L I/P  
5
LINE IN L  
6
7
LINE IN R  
GND  
8
CD N GND  
CD IN R I/P  
LINE OUT R  
GND  
9
10  
12  
14  
11  
13  
LINE OUT L  
GND  
SBC-776 Chapter 2 31  
SBC-776  
Floppy Drive Connector (CN12)  
Floppy drive connector (CN12)  
Pin  
1
Signal  
GND  
GND  
GND  
GND  
GND  
GND  
GND  
GND  
GND  
GND  
GND  
GND  
GND  
GND  
GND  
GND  
GND  
Pin  
2
Signal  
DENSITY SELECT  
3
4
N/C  
5
6
DRIVE TYPE  
INDEX  
7
8
9
10  
12  
14  
16  
18  
20  
22  
24  
26  
28  
30  
32  
34  
MOTOR 0  
11  
13  
15  
17  
19  
21  
23  
25  
27  
29  
31  
33  
DRIVE SELECT 1  
DRIVE SELECT 2  
MOTOR 1  
DIRECTION  
STEP  
WRITE DATA  
WRITE GATE  
TRACK 0  
WRITE PROTECT  
READ DATA  
HEAD DELECT  
DISK CHANGE  
PS/ 2 Keyboa rd a nd Mouse Connector (CN13)  
On board SBC-776, there is a standard 6-pin header for PS/2  
keyboard and mouse connector. The pin definition is provided  
below.  
Keyboard and mouse connector (CN 13)  
Pin  
1
3
Signal  
KB DATA  
GND  
Pin  
2
4
Signal  
MS DATA  
VCC  
5
KB CLOCK  
6
MS CLOCK  
3 2  
SBC-776 ManualBC-599/596  
Pa ra llel port connector (CN14)  
Normally, the parallel port is used to connect the board to a printer.  
The SBC-776 includes an onboard parallel port, accessed through  
CN14, a 26-pin flat-cable connector. A traditional DB-25 connector  
cable is needed to install the printer to the board. The cable has a  
26-pin connector on one end and a DB-25 connector on the other.  
Parallel port IRQ  
The onboard parallel port is designated as LPT1 and can be  
disabled or changed to LPT2 or LPT3 in the system BIOS setup.  
Parallel port connector table (CN14)  
Parallel port connector (CN14)  
Pin  
1
Signal  
Pin  
2
Signal  
D0  
/STB  
D1  
3
4
D2  
5
D3  
6
D4  
7
D5  
8
D6  
9
D7  
10  
12  
14  
16  
18  
20  
22  
24  
26  
/ACK  
11  
13  
15  
17  
19  
21  
23  
25  
BUSY  
SLCT  
/ERR  
/SLCTINI  
PE  
/AUTOFD  
/INIT  
GND  
GND  
GND  
GND  
N/C  
GND  
GND  
GND  
GND  
SBC-776 Chapter 2 33  
SBC-776  
COM 1 (CN 15) & COM 2 (CN 16) Seria l Ports  
On board offer four set serial ports for serial devices connection.  
Two of them are the D-Sub type, pin definition show as below, for  
another two, please refer to page ?.  
COM 1 RS-232 (CN15)  
Pin  
1
2
Signal  
Pin  
6
7
Signal  
SDCDB1X  
SRXDB1  
STXDB1  
SDSRB1X  
SRTSB1X  
SCTSB1X  
3
8
4
5
SDTRB1X  
GND  
9
SRIB1X  
NC  
10  
COM 1 RS-232 (CN16)  
Pin  
1
2
Signal  
SDCDB2X  
SRXDB2  
Pin  
6
7
Signal  
SDSRB2X  
SRTSB2X  
3
4
5
STXDB2  
SDTRB2X  
GND  
8
SCTSB2X  
SRIB2X  
NC  
9
10  
3 4  
SBC-776 ManualBC-599/596  
SCSI -2  
68-PinConnector (CN 21)  
SBC-776 has a 68 pin connector for the Ultra 2 SCSI connection.  
Please pay attention when connecting the SCSI device, because  
you must determine the last device on the SCSI chain.  
PIN  
1
2
3
4
5
6
7
8
FUNCTION  
SD+12  
SD+13  
SD+14  
SD+15  
SDP+1  
SD+0  
SD+1  
SD+2  
SD+3  
SD+4  
SD+5  
SD+6  
SD+7  
SDP + 0  
GND  
PIN  
35  
36  
37  
38  
39  
40  
41  
42  
43  
44  
45  
46  
47  
48  
49  
50  
51  
52  
53  
54  
55  
56  
57  
58  
59  
60  
61  
62  
63  
64  
65  
66  
67  
68  
FUNCTION  
SD-12  
SD-13  
SD-14  
SD-15  
SDP-1  
SD-0  
SD-1  
SD-2  
SD-3  
SD-4  
SD-5  
SD-6  
SD-7  
SDP - 0  
GND  
SENIN  
TPWEX  
TPWEX  
NC  
GND  
SATN-  
GND  
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
DIFS  
TPWEX  
TPWEX  
NC  
GND  
SATN+  
GND  
SBSY+  
SACK+  
SRST+  
SMSG+  
SSEL+  
SCD +  
SREQ+  
SIO+  
SBSY-  
SACK-  
SRST-  
SMSG-  
SSEL-  
SCD-  
SREQ-  
SIO-  
SD-8  
SD+8  
SD+9  
SD+10  
SD+11  
SD-9  
SD-10  
SD-11  
SBC-776 Chapter 2 35  
SBC-776  
100Ba se-Tx LAN connector (CN22,20)  
On board supports one standard RJ-45 connector for enthernet  
connection. The RJ-45 connector has two LED indicators. Both  
LED displays indicate the speed of information being processed,  
however the Lan speed does vary.  
* The on board Intel 82559XX fast ethernet controller supports  
10Mb/s and 100Mb/s N-way auto-negotiation operation.  
Green LED: 100M LAN speed  
Yellow LED: 10M LAN speed  
100Base-Tx Ethernet connector (CN22)  
Pin  
1
2
Signal  
Tx+  
TX-  
Pin  
5
6
Sig  
N/C  
RX-  
3
4
RX+  
N/C  
7
8
N/C  
N/C  
Green LED: 100M LAN speed  
Yellow LED: 10M LAN speed  
100Base-Tx Ethernet connector (CN20)  
Pin  
1
2
Signal  
Tx+  
TX-  
Pin  
5
6
Sig  
N/C  
RX-  
3
4
RX+  
N/C  
7
8
N/C  
N/C  
3 6  
SBC-776 ManualBC-599/596  
Pow e r conne ctor (CN23)  
ATX power connector (CN23)  
The ATX power supply uses 20-pin connector shown below. Make  
sure you plug in the right direction.  
ATX power connector (CN23)  
Pin  
Signal  
Pin  
Signal  
1
+3.3V  
11  
+3.3V  
2
+3.3V  
GND  
12  
13  
14  
15  
16  
17  
18  
19  
20  
-12V  
3
GND  
POWER ON  
GND  
GND  
GND  
-5V  
4
+5V  
5
GND  
6
+5 V  
7
GND  
8
POWER OK  
+5VSB  
+12V  
9
+5V  
10  
+5V  
Spea ker/ Buzzer (CN 24)  
You can choose to use the internal buzzer on the SBC-776 baord, or  
you may use your own external speaker.  
Speaker/ Buzzer (CN24)  
Speaker  
On Board Buzzer  
3 4  
1 2 3 4  
1
2
CN24  
SBC-776 Chapter 2 37  
SBC-776  
Fa n pow er connectors (CN25, 26, 27)  
CPU fan pow er connector (CN 26)  
Plug in the fan cable to the 3-pin fan connector onboard. The fan  
connector is marked CN26.  
CPU fan power connector (CN26)  
Pin  
Signal  
1
GND  
2
3
+12V  
Fan speed sensor  
System fan 1 connector (CN 25)  
Pin  
Signal  
1
GND  
2
3
+12V  
Fan speed sensor  
System fan 2 connector (CN27)  
Pin  
1
Signal  
GND  
2
+12V  
3
Fan speed sensor  
3 8  
SBC-776 ManualBC-599/596  
LCD Ba cklight Pow er Connector (CN 28)  
LCD Backlight Power Connector (CN 28)  
Pin  
1
2
Signal  
BLKVCC  
GND  
TFT LCD pa nel connector (CN 29)  
LCD panel connector (CN 29)  
Pin  
1
3
5
7
Signal  
BLKVCC  
GND  
LDCVCC  
ENAVEE  
P0  
Pin  
2
4
6
8
Signal  
BLKVCC  
GND  
LCDVCC  
GND  
P1  
9
10  
12  
14  
16  
18  
20  
22  
24  
26  
28  
30  
32  
34  
36  
38  
40  
42  
44  
46  
48  
11  
13  
15  
17  
19  
21  
23  
25  
27  
29  
31  
33  
35  
37  
39  
41  
43  
45  
47  
P2  
P4  
P6  
P8  
P10  
P12  
P14  
P16  
P18  
P20  
P22  
P24  
SHFCLK  
DE  
GND  
P26  
P28  
P30  
P3  
P5  
P7  
P9  
P11  
P13  
P15  
P17  
P19  
P21  
P23  
P25  
VSYNC  
HSYNC  
FPBLEN  
P27  
P29  
P31  
P32  
P33  
49  
P34  
50  
P35  
SBC-776 Chapter 2 39  
SBC-776  
PS/ 2 Keyboa rd Hea der (CN31)  
Onboard there is a 5-pin header for keybaord connection, the pin  
definition is provided below.  
PS/2 Keyboard Header (CN 31)  
Pin  
1
3
Signal  
KB CLOCK  
NC  
Pin  
2
4
Signal  
KB DATA  
GND  
5
VCC  
PS/ 2 Mouse Hea der (CN 32)  
Onboard there is a 4-pin header for keyboard connection, the pin  
definition is provided below.  
PS/2 Mouse Header (CN 32)  
Pin  
1
3
Signal  
MS CLOCK  
GND  
Pin  
2
4
Signal  
MS DATA  
VCC  
4 0  
SBC-776 ManualBC-599/596  
3
Award BIOS Setup  
This chapter describes how to configure  
the BIOS for the system.  
42 SBC-776 User Manual  
Starting setup  
The Award BIOS is immediately activated when you first turn on  
the computer. The BIOS reads system configuration information in  
CMOS RAM and begins the process of checking out the system  
and configuring it through the power-on self test (POST).  
When these preliminaries are finished, the BIOS seeks an operating  
system on one of the data storage devices (hard drive, floppy drive,  
etc.). The BIOS launches the operating system and hands control of  
system operations to it.  
During POST, you can start the Setup program in one of two ways:  
1.By pressing Del immediately after switching the system on, or  
2.By pressing Del or pressing Ctrl-Alt-Esc when the following  
message appears briefly at the bottom of the screen during POST:  
TO ENTER SETUP BEFORE BOOT PRESS DEL KEY  
If the message disappears before you respond and you still wish to  
enter Setup, restart the system to try again by turning it OFF then  
ON or pressing the RESET button on the system case. You may  
also restart by simultaneously pressing Ctr-Alt-Del. If you do not  
press the keys at the correct time and the system does not boot, an  
error message appears and you are again asked to  
PRESS F1 TO CONTINUE, DEL TO ENTER SETUP  
Chapter 3 Award BIOS Setup 43  
Setup keys  
These keys helps you navigate in Award BIOS:  
Up arrow  
Down arrow  
Left arrow  
Right arrow  
Esc  
Move to previous item  
Move to next item  
Move to the item in the left hand  
Move to the item in the right hand  
Main Menu: Quit and not save changes into  
CMOS RAM  
Other pages: Exit current page and return to  
Main Menu  
PgUP/+  
PgDn/-  
F1  
Increase the numeric value or make  
changes  
Decrease the numeric value or make  
changes  
General help, only for Status Page Setup  
Menu and Option Page Setup Menu  
F2  
F3  
F4  
F5  
Item Help  
Reserved  
Reserved  
Restore the previous CMOS value from  
CMOS, only for Option Page Setup Menu  
Load the default CMOS RAM value from  
BIOS default table, only for Option Page  
Setup Menu  
F6  
F7  
F8  
Load the default  
Reserved  
F9  
Reserved  
F10  
Save all the CMOS changes, only for Main  
Menu  
44 SBC-776 User Manual  
Getting help  
Press F1 to pop up a small help window that describes the appro-  
priate keys to use and the possible selections for the highlighted  
item. To exit the Help Window press Esc or the F1 key again.  
In Ca se of Proble m s  
If, after making and saving system changes with Setup, you  
discover that your computer no longer is able to boot, the Award  
BIOS supports an override to the CMOS settings that resets your  
system to its default configuration.  
You can invoke this override by immediately pressing Insert; when  
you restart your computer. You can restart by either using the ON/  
OFF switch, the RESET button or by pressing Ctrl-Alt-Delete.  
The best advice is to alter only settings that you thoroughly  
understand. In particular, do not change settings in the Chipset  
screen without a good reason. The Chipset defaults have been  
carefully chosen by Award Software or your system manufacturer  
for the best performance and reliability. Even a seemingly small  
change to the Chipset setup may cause the system to become  
unstable.  
Chapter 3 Award BIOS Setup 45  
Main Setup Menu  
Standard CMOS Features  
Use this menu for basic system configuration. (Date, time, IDE,  
etc.)  
Advanced BIOS Features  
Use this menu to set the advanced features available on your  
system.  
Advanced Chipset Features  
Use this menu to change the values in the chipset registers and  
optimize your system’s performance.  
Integrated Peripherals  
Use this menu to specify your settings for integrated peripherals.  
(Primary slave, secondary slave, keyboard, mouse etc.)  
Power Management Setup  
Use this menu to specify your settings for power management.  
(HDD power down, power on by ring, KB wake up, etc.)  
46 SBC-776 User Manual  
PnP/PCI Configuration  
This entry appears is your system supports PnP/PCI.  
PC Health Status  
This menu allows you to set the shutdown temperature for your  
system.  
Frequency/Voltage Control  
Use this menu to specify your settings for frequency/ voltage  
control.  
Load Fail-Safe Defaults  
Use this menu to load the BIOS default values for the minimal/  
stable performance for your system to operate.  
Load Optimized Defaults  
Use this menu to load the BIOS default values that are factory  
settings for optimal performance system operations. While  
AWARD has designated the custom BIOS to maximize perfor-  
mance, the factory has the right to change these defaults to meet  
their needs.  
Set Supervisor/User Password  
Use this menu to set User and Supervisor Passwords.  
Save and Exit Setup  
Save CMOS value changes to CMOS and exit setup.  
Exit Without Saving  
Abandon all CMOS value changes and exit setup.  
Chapter 3 Award BIOS Setup 47  
Standard CMOS Features  
This standard setup menu allows users to configure system  
components such as the date, time, hard disk drive, floppy drive,  
display, and memory. Online help for each field can be accessed  
by pressing F1.  
Date and Time Configuration  
The BIOS determines the day of the week from the other date  
information. This field is for information only.  
Press the left or right arrow key to move to the desired field (date,  
month, year). Press the PgUp/- or PgDn/+ key to increment the  
setting, or type the desired value into the field.  
The time format is based on the 24-hour military-time clock. For  
example, 1 p.m. is 13:00:00 hours. Press the left or right arrow key  
to move to the desired field. Press the PgUp/- or PgDn/+ key to  
increment the setting, or type the desired value into the field.  
HARD DISKS  
The BIOS supports up to four IDE drives. This section does not  
show information about other IDE devices, such as a CD-ROM  
drive, or about other hard drive types, such as SCSI drives.  
NOTE: We recommend that you select type AUTO for all drives.  
48 SBC-776 User Manual  
The BIOS can automatically detect the specifications and optimal  
operating mode of almost all IDE hard drives. When you select  
type AUTO for a hard drive, the BIOS detects its specifications  
If you do not want to select drive type AUTO, other methods of  
selecting the drive type are available:  
1.Match the specifications of your installed IDE hard drive(s) with  
the preprogrammed values for drive types 1 through 45.  
2.Select USER and enter values into each drive parameter field.  
3.Use the IDE HDD AUTO DETECTION function in Setup.  
Here is a brief explanation of drive specifications:  
Type: The BIOS contains a table of predefined drive types. Each  
defined drive type has a specified number of cylinders,  
number of heads, write precompensation factor, landing  
zone, and number of sectors. Drives whose specifications  
do not accommodate any predefined type are classified as  
type USER.  
Size: Disk drive capacity (approximate). Note that this size is  
usually slightly greater than the size of a formatted disk  
given by a disk-checking program.  
Cyls: Number of cylinders  
Head: Number of heads  
Precomp: Write precompensation cylinder  
Landz: Landing zone  
Sector: Number of sectors  
Mode: Auto, Normal, Large, or LBA  
- Auto: The BIOS automatically determines the optimal mode.  
- Normal: Maximum number of cylinders, heads, and sectors  
supported are 1024, 16, and 63.  
- Large: For drives that do not support LBA and have more  
than 1024 cylinders.  
Chapter 3 Award BIOS Setup 49  
- LBA (Logical Block Addressing): During drive access, the  
IDE controller transforms the data address described by  
sector, head, and cylinder number into a physical block address,  
significantly improving data transfer rates. For drives with greater  
than 1024 cylinders.  
Drive A  
Drive B  
Select the correct specifications for the diskette drive(s) installed in  
the computer.  
None  
No diskette drive installed  
360K, 5.25 in  
5-1/4 inch PC-type standard drive;  
360 kilobyte capacity  
1.2M, 5.25 in  
5-1/4 inch AT-type high-density  
drive; 1.2 megabyte capacity  
720K, 3.5 in  
3-1/2 inch double-sided drive;  
720 kilobyte capacity  
1.44M, 3.5 in  
3-1/2 inch double-sided drive;  
1.44 mega byte capacity  
2.88M, 3.5 in  
3-1/2 inch double-sided drive;  
2.88 mega byte capacity  
Video  
Select the type of primary video subsystem in your computer. The  
BIOS usually detects the correct video type automatically. The  
BIOS supports a secondary video subsystem, but you do not select  
it in Setup.  
EGA/VGA Enhanced Graphics Adapter/Video Graphics Array.  
For EGA, VGA, SEGA, SVGA, or PGA monitor adapters.  
CGA 40 Color Graphics Adapter, power up in 40 column mode  
CGA 80 Color Graphics Adapter, power up in 80 column mode  
MONO  
Monochromoe adapter, includes high resolution  
monochrome adapters  
50 SBC-776 User Manual  
Halt On  
During the power-on-self-test (POST), the computer stops if the  
BIOS detects a hardware error. You can tell the BIOS to ignore  
certain errors during POST and continue the boot-up process.  
These are the selections:  
No errors: POST does not stop for any errors.  
All errors If: the BIOS detects any nonfatal error, POST  
stops and prompts you to take corrective action.  
All, But Keyboard: POST does not stop for a keyboard  
error, but stops for all other errors  
All, But Diskette: POST does not stop for diskette drive  
errors, but stops for all other errors.  
All, But Disk/Key: POST does not stop for a keyboard or  
disk error, but stops for all other errors.  
Memory  
You cannot change any values in the Memory fields; they are only  
for your information. The fields show the total installed random  
access memory (RAM) and amounts allocated to base memory,  
extended memory, and other (high) memory. RAM is counted in  
kilobytes (KB: approximately one thousand bytes) and megabytes  
(MB: approximately one million bytes).  
RAM is the computer's working memory, where the computer  
stores programs and data currently being used, so they are accessi-  
ble to the CPU. Modern personal computers may contain up to 64  
MB, 128 MB, or more.  
Base Memory  
Typically 640 KB. Also called conventional memory. The DOS  
operating system and conventional applications use this area.  
Chapter 3 Award BIOS Setup 51  
Extended Memory  
Above the 1-MB boundary. Early IBM personal computers could  
not use memory above 1 MB, but current PCs and their software  
can use extended memory.  
Other Memory  
Between 640 KB and 1 MB; often called High memory. DOS may  
load, terminate-and-stay-resident (TSR) programs, such as device  
drivers, in this area, to free as much conventional memory as  
possible for applications. Lines in your CONFIG.SYS file that start  
with LOADHIGH, load programs into high memory.  
52 SBC-776 User Manual  
Advanced BIOS Features  
The displayed configuration is based on the manufacturer's SETUP  
DEFAULTS settings.  
Virus Warning  
When enabled, you receive a warning message if a program  
(specifically, a virus) attempts to write to the boot sector or the  
partition table of the hard disk drive. You should then run an anti-  
virus program. Keep in mind that this feature protects only the boot  
sector, not the entire hard drive.  
NOTE: Many disk diagnostic programs that access the boot sector  
table can trigger the virus warning message. If you plan to run  
such a program, we recommend that you first disable the virus  
warning.  
Chapter 3 Award BIOS Setup 53  
CPU Internal Cache/External Cache  
Cache memory is additional memory that is much faster than  
conventional DRAM (system memory). CPUs from 486-type on up  
contain internal cache memory, and most, but not all, modern PCs  
have additional (external) cache memory. When the CPU requests  
data, the system transfers the requested data from the main DRAM  
into cache memory, for even faster access by the CPU.  
The External Cache field may not appear if your system does not  
have external cache memory.  
CPU L2 Cache ECC Checking  
When you select Enabled, memory checking is enable when the  
external cache contains ECC SRAMs.  
Processor Number Feature  
This option is for Pentium III processor. During Enabled, this will  
check the CPU Serial number. Disabled this option if you don't  
want the system to know the serial number.  
Quick Power On Self Test  
Select Enabled to reduce the amount of time required to run the  
power-on-self-test (POST). A quick POST skips certain steps. We  
recommend that you normally disable quick POST. Better to find a  
problem during POST than lose data during your work.  
First/Second/Third/Fourth Boot Device  
The BIOS attempts to load the operating system from the devices  
in the sequence selected in these items.  
The choices: Floppy, LS/ZIP, HDD, SCSI, CDROM, Disable.  
54 SBC-776 User Manual  
Swap Floppy Drive  
This field is effective only in systems with two floppy drives.  
Selecting enabled assigns physical drive B to logical drive A, and  
physical drive A to logical drive B.  
Boot Up Floppy Seek  
When Enabled, the BIOS tests (seeks) floppy drives to determine  
whether they have 40 or 80 tracks. Only 360-KB floppy drives  
have 40 tracks; drives with 720 KB, 1.2 MB, and 1.44 MB  
capacity all have 80 tracks. Because very few modern PCs have  
40-track floppy drives, we recommend that you set this field to  
Disabled to save time.  
Boot Up NumLock Status  
Toggle between On or Off to control the state of the NumLock key  
when the system boots. When toggled On, the numeric keypad  
generates numbers instead of controlling cursor operations.  
Gate A20 Option  
Gate A20 refers to the way the system addresses memory above 1  
MB (extended memory). When set to Fast, the system chipset  
controls Gate A20. When set to Normal, a pin in the keyboard  
controller controls Gate A20. Setting Gate A20 to Fast improves  
system speed, particularly with OS/2 and Windows.  
Chapter 3 Award BIOS Setup 55  
Typematic Rate Setting- Key strokes repeat at a  
rate determined by the keyboard controller. When  
enabled, the typematic rate and typematic delay can be  
selected.  
The choice: Enabled/Disabled  
Security Option  
If you have set a password, select whether the password  
is required every time the System boots, or only when you enter  
Setup.  
OS Select For DRAM>64MB-Select the  
operating system that is running with greater than 64MB  
or RAM on the system.  
The choice: Non-OS2, OS2  
56 SBC-776 User Manual  
HDD S.M.A.R.T Capability  
Hard disk drives have built in problem detection  
capability (Self-Monitoring Analysis and Reporting Technology).  
If a foreseen problem is about to take place, the computer will  
give a you a warning signal. The choice: Enable, Disable  
Report No FDD For WIN 95- Report  
no FDD for Win 95 or not. The choice: Yes, no  
Chapter 3 Award BIOS Setup 57  
Advanced Chipset Features  
SDRAM CAS Latency Time  
When synchronous DRAM is installed, the number of clock cycles of  
CAS latency depends on the DRAM timing. Do not reset this field from  
the default value specified by the system designer.  
SDRAM Cycle Time Tras/Trc  
Select the number of SCLKs for an access cycle.  
The choices: 5/7, 7/9 disable.  
SDRAM RAS-to-CAS Delay  
This field lets you insert a timing delay between the CAS and RAS strobe  
signals, used when DRAM is written to, read from, or refreshed. Fast  
gives faster performance; slow gives more stable performance. This field  
applies only when synchronous DRAM is installed in the system.  
58 SBC-776 User Manual  
SDRAM RAS Precharge Time  
If an insufficient number of cycles is allowed for the RAS to accumulate  
its charge before DRAM refresh, the refresh may be incomplete and the  
DRAM may fail to retain date. Fast gives faster performance; slow gives  
more stable performance. This field applies only when synchronous  
DRAM is installed in the system.  
System BIOS Cacheable  
Selecting Enabled allows caching of the system BIOS ROM at F0000h-  
FFFFFh, resulting in better system performance. However, if any program  
writes to this memory area, a system error may result. The choices:  
Enabled, Disabled  
Video BIOS Cacheable  
Selecting Enabled allows caching of the video BIOS ROM at C0000h to  
C7FFFh, resulting in better video performance. However, if any program  
writes to this memory area, a system error may result. The choices:  
Enabled, Disabled Memory  
Hole At 15-16m  
In order to improve performance, certain space in memory is reserved for  
ISA cards. This memory must be mapped into the memory. The choices:  
15-16 M, disabled  
CPU Latency Timer  
During enable, a deferrable CPU cycle will only be Deferred after it has  
been in Snoop Stall for 31 clocks and another ADS# has arrived. During  
disable, a deferrable CPU cycle will be deferred immediately after the  
GMCH receives another ADS#.  
Delayed Transaction  
The chipset has an embedded 32-bit posted write buffer to support delay  
transactions cycles. Select Enabled to support compliance with PCI  
specification version 2.1.  
Chapter 3 Award BIOS Setup 59  
AGP Graphics Aperture Size  
Select the size of Accelerated Graphics Port (AGP) aperture. The  
aperture is a portion of the PCI memory address range dedicated for  
graphics memory address space. Host cycles that hit the aperture range  
are forwarded to the AGP without any translation. The choices: 32M,  
64M.  
Display Cache Frequency  
Display cache frequency will allow for the level the of the share memory  
provided by the Intel 815E chipset to be adjusted.  
The settings are 100MHz and 133 MHz.  
System Memory Frequency  
Select the onboard display cache frequency. The settings are auto,  
100MHz and 133MHz.  
On-Chip Video Window Size  
Select the on-chip video window size for VGA drive use.  
The choices: 32MB, 64MB, Disabled  
Initial Display Cache  
Cas# Latency  
Select the local memory clock period. The number of  
clock cycles of CAS# Latency depends on the Onboard  
Display Cache timing. The choice: 2,3  
Paging Mode Control  
Select the paging mode control. The choice: open,  
close  
RAS-to-CAS Override  
This item allows you to insert a timing delay between the  
CAS and RAS strobe signals, used when Onboard  
display cache is written to, read from, or refreshed.  
During by CAS#LT, this will depend on the Onboard  
Display Cache CAS# Latency setting. During Override  
(2), RAS-to-CAS time = 2  
Ras# Timing  
This item controls RAS# active to Precharge, and refresh  
to RAS# active delay ( in local memory clock ). The  
choices: Fast, Slow  
Ras# Precharge Timing  
This item controls RAS# precharge ( in loca memory  
clocks). The choices: Fast, slow  
60 SBC-776 User Manual  
Integrated Peripherals  
On-Chip Primary PCI IDE  
The system chipset contains a PCI IDE interface with support for  
two IDE channels. Select Enabled to activate the primary and/or  
secondary IDE interface. Select Disabled to deactivate this  
interface, if you install a primary and/or secondary add-in IDE  
interface.  
On-Chip Secondary PCI IDE  
The chipset contains a PCI IDE interface with support for two IDE  
channels. Select Enabled to activate the secondary IDE interface.  
Select Disabled to deactivate this interface.  
The choices: Enable, Disable  
IDE Primary/Secondary Master/Slave PIO  
The four IDE PIO (Programmable Input/Output) fields let you set a  
PIO mode (0-1) for each of the four IDE devices that the onboard  
IDE interface supports. Modes 0 through 4 provide successively  
increased performance. In Auto mode, the system automatically  
determines the best mode for each device.  
The choices: Auto, Mode 0, Mode 1, Mode 2, Mode 3, Mode 4.  
Chapter 3 Award BIOS Setup 61  
IDE Primary/Secondary Master/Slave UDMA  
Ultra DMA/33 implementation is possible only if your IDE hard  
drive supports it and the operating environment includes a DMA  
driver (Windows 95 OSR2 or a third-party IDE bus master driver).  
If your hard drive and your system software both support Ultra  
DMA/33, select Auto to enable BIOS support.  
The choices: Auto, disable  
USB Controller  
Select Enabled if your system contains a Universal Serial Bus  
controller and you have USB peripherals.  
USB Keyboard Support  
Select Enabled if your system contains a Universal Serial Bus  
controller and you have a USB keyboard.  
Init Display First  
This item allows you to active PCI slot or onboard first.  
The choice: PCI slot, onboard  
AC97 Audio  
The default setting of Auto enables the AC97 audio if it is detected  
onboard  
Onboard/CRN LAN selection  
Testing purposes only. Leave this function in the AUTO setting.  
8-bit I/O Recovery Time  
The I/O recovery mechanism adds bus clock cycles between PCI-  
originated I/O cycles to the ISA bus. This delay takes place  
because the PCI bus is much faster than the ISA bus. This field  
lets you add recovery time (in bus clock cycles) for 8-bit I/O.  
The choice: 0-7 SYSCLK  
62 SBC-776 User Manual  
16-bit I/O Recovery Time  
The I/O recovery mechanism adds bus clock cycles between PCI-  
originated I/O cycles to the ISA bus. This delay takes place  
because the PCI bus is much faster than the ISA bus. This field  
lets you add recovery time (in bus clock cycles) for 16-bit I/O.  
The choice: 1 SYSCLK, 2SYSCLK, 3SYSCLK, 4 SYSCLK  
IDE HDD Block Mode  
Block mode is also called block transfer, multiple commands, or  
multiple sector read/write. If your IDE hard drive supports block  
mode (most new drives do), select Enabled for automatic detection  
of the optimal number of block read/write per sector the drive can  
support.  
Power on Function  
Select the different manners for powering on the system.  
The choices: Keyboard 98, password, any key, hot key, button  
only, mouse click, mouse move.  
KB Power on Password  
The system will ask for a password, after entering the correct  
password the keyboard can then be used.  
Ir Transmission Delay  
The system IR component transmits and retrieves data from its  
working environment, if enabled the IR system will detect or  
transmit information. If disabled the IR system will be unable to  
operate.  
Use IR Pins  
Consult your IR peripheral documentation to select the correct  
setting of the TxD and RxD signals.  
Chapter 3 Award BIOS Setup 63  
Hot Key Power On  
Simply pressing on the pre-selected keyboard key the system will  
power on.  
Onboard FDC Controller  
Select Enabled if your system has a floppy disk controller (FDC)  
installed on the system board and you wish to use it. If you install  
an add-in FDC or the system has no floppy drive, select Disabled  
in this field.  
UART Mode Select  
Select an operating mode for the second serial port:  
Normal  
RS-232C serial port  
IrDA 1.0  
Infrared port compliant with IrDA 1.0  
specification  
IrDA SIR  
IrDA MIR  
IrDA FIR  
ASK IR  
SCR  
IrDA-compliant serial infrared port  
1 MB/sec infrared port  
Fast infrared standard  
Amplitude shift keyed infrared port  
RxD, TxD Active  
Consult your IR peripheral documention to select the correct  
setting of the TxD and RxD signals  
UR2 Duplex Mode  
Select the value required by the IR device connected to the IR prot.  
Full-duplex mode permits simultaneous two-direction transmission.  
Half-duplex mode permits transmission in one direction only at a  
time. If no infrared port is present in the system, select disabled.  
Use IR Pins  
Consult your IR peripheral documentation to select the correct  
setting of the TxD and RxD signals.  
64 SBC-776 User Manual  
Onboard Serial Ports (1, 2)  
Normally, the main board’s I/O chips will occupy a certain portion  
of memory space. For each I/O device the computer provides an  
I/O address. The more devices attached the more address needed  
to organize the memory storage areas. If all the I/O devices were  
run through the same address, your devices would come to a near  
halt. By providing the end user with four serial ports this allows  
devices to run more efficiently if needed. Also the corresponding  
interrupt needs to be selected.  
Selections of logical COM port addresses are as follows. ( 3F8/  
IRQ4, 3E8/IRQ4, 2F8/IRQ3, 2E8/IRQ3)  
Onboard Parallel Port  
Select a logical LPT port address and corresponding interrupt for  
the physical parallel port  
The Choice: 378/IRQ7, 278/IRQ5, 3BC/IRQ7, disabled  
Parallel Port Mode  
Two bidirectional parallel ports. Supports SPP, ECP, EPP,  
ECP + EPP.  
EPP Mode Select  
Select the EPP port type 1.7 or 1.9  
ECP Mode Use DMA  
Select a DMA channel for the port.  
PWRON After PWR-Fail  
This option will determine how the system will power on after a  
power failure.  
The choice: off, on , former status  
Chapter 3 Award BIOS Setup 65  
Watch Dog Timer  
You can enable the system watchdog timer, a hardware timer that  
generates either an NMI or a reset when the software that it  
monitors does not respond as expected each time the watch dog  
polls it ( select the time period in a separate field ) The choice:  
Disabled, 20 sec, 30 sec, 40 sec, 50 sec, 1 min, 2 min, 4 min.  
66 SBC-776 User Manual  
Power Management Setup  
ACPI Function  
This item allows you to enable/disable the Advanced Configuration  
and Power Management (ACPI). The Choices: Enable/Disable  
ACPI Suspend Type  
This item will set which ACPI suspend type will be used.  
S1 (POS) The S1 sleeping state is low wake-up latency sleeping  
state. In this state, no system context is lost (CPU or chip set) and  
hardware maintains all system context.  
S3 (STR) The S3 state is a low wake-up latency sleeping state  
where all system context is lost expect system memory. CPU,  
cache and chipset context are lost in this state. Hardware maintains  
memory context and restores some CPU and L2 configuration  
context.  
Chapter 3 Award BIOS Setup 67  
Power Management  
This category allows you to select the type ( or degree ) of power  
saving and is directly related to the following modes:  
1. HDD Power Down  
2. Doze Mode  
3. Suspend Mode  
Disable (Default)  
No power management. Disable all four modes.  
Minimum power managemen. Doze mode = 1  
hour. Standby mode = 1 hour. Suspend mode =  
1 hour. HDD Power Down =15 minutes.  
Min. Power Saving  
Maximum power management--ONLY  
AVAILABLE FOR SL CPU’S. Dose mode =  
1 min., Standby mode = 1 min., Suspend mode  
= 1 min., and HDD Power Down = 1 min.  
Max.Power Saving  
User Defined  
Allows you to set each mode individually. When  
not disabled, each of the tanges are from 1 min.  
to 1 hour except for HDD Power Down which  
ranges from 1 min. to 15 min. and disable.  
Video Off Method  
This determines the manner in which the monitor is blanked.  
This selection will cause the system to turn off  
V/H SYNC + Blank  
the vertical and horizontal synchronization ports  
and write blanks to the video buffer  
Blank Screen  
DPMS  
This option only writes blanks to the video buffer  
Initial display power management signaling  
68 SBC-776 User Manual  
Video Off In Suspend  
After the selected period of system inactivity, the chipset enters a  
hardware suspend mode, stopping the CPU clock and possibly  
causing other system devices to enter power management modes.  
In this case the video hardware can be selected to shut off after a  
period of system inactivity. This determines the manner in which  
the monitor is blanked.  
Suspend Type  
Select the suspend type. The choice: PWRON suspend, Stop  
Grant  
MODEM use IRQ  
This determines the IRQ in which the MODEM can use.  
The choices: 3, 4, 5, 7, 9, 10, 11, NA  
Suspend Mode  
After the selected period of system inactivity, the chipset enters a  
hardware suspend mode, stopping the CPU clock and possibly  
causing other system devices to enter power management modes.  
Soft-Off by PWR-BTTN  
Pressing the power button for more than 4 seconds forces the  
system to enter the Soft-Off state when the system has hung. The  
choice: Delay 4 seconds, Instant-Off.  
Wake Up On PCI Card  
This will enable the system to wake up through PCI card  
peripheral. The choice: Enable/Disable  
Power On By Ring  
An input signal on the serial Ring Indicator (RI) line (in other  
words, an incoming call on the modem) boots the system from a  
soft off state.  
Chapter 3 Award BIOS Setup 69  
USB KB Wake-up From S3  
This option is used to Enabled/Disabled USB keyboard wake up  
with suspend to RAM. The Choice: Enabled/Disabled  
Power On after Power Fail  
After initial power failure, the system will attempt to power up  
again in the setting that the end user has selected.  
The Choice: ON/OFF/Former status  
CPU Thermal-Throttling  
Select the CPU Thermal-Throttling rate for your system.  
The choice: 12.5%, 25%, 37.5%, 50%, 62.5% 75%, 87.5%  
Resume By Alarm  
This option is used to Enable/Disable USB keyboard wake up with  
suspend to RAM.  
The choices: Enable, disable  
Date Alarm  
You can choose which month the system will boot up. Set to 0 to  
boot everyday.  
Time Alarm  
You can choose what hour, minute and second the system will boot  
up.  
70 SBC-776 User Manual  
<Reload Global Timer Events>  
PM events are I/O events whose occurrence can prevent  
the system from entering a power saving mode or can  
awaken the system from such a mode. In effect, the  
system remains alert for anything which occurs to a device  
which is configured as Enabled, even when the system is  
in a power down mode.  
Primary IDE 0  
Primary IDE 1  
Secondary IDE 0  
Secondary IDE 1  
FDD, COM, LPT Port  
PCI PIRQ (A-D)#  
Chapter 3 Award BIOS Setup 71  
PnP/ PCI Configurations  
PNP OS Installed  
This item allows you to determine whether the PnP OS is installed  
or not. Select Yes if the system operating environment is Plug and  
Play aware. The settings are Yes or No.  
Reset Configuration Data  
Normally, you leave this field disabled. Select enabled to reset  
Extended System Configuration Data (ESCD) when you exit Setup  
if you have installed a new add-on and the system reconfiguration  
has caused such a serious conflict that the operating system can not  
boot. The choices: Enabled, Disabled  
72 SBC-776 User Manual  
Resources Controlled By  
The Award Plug and Play BIOS has the capacity to automatically  
configure all of the boot and Plug and Play compatible devices.  
However, this capability means absolutely nothing unless you are  
using a Plug and Play operating system such as Windows ® 95. If  
you set this field to “manual” choose specific resources by going  
into each of the sub menu that follows this field ( a sub menu is  
proceeded by a “>”. The choices: Auto, Manual.  
PCI/VGA Palette Snoop  
Leave this field at Disabled. Choices: Enabled, Disabled.  
Chapter 3 Award BIOS Setup 73  
PC Health Status  
CPU Warning Temperature  
During enabled, this will warn the user when the CPU temperature  
reach a certain temperature.  
Options: Disabled, 75°C/167°F, 70°C/158°F, 65°C/149°F,  
60°C/140°F  
Shutdown Temperature  
Your system can be configured to shutdown once reaching a certain  
temperature. To protect your system from overheating or damage,  
select a certain temperature level in the PC Health Status menu.  
Options: Disabled, 75°C/167°F, 70°C/158°F, 65°C/149°F,  
60°C/140°F  
74 SBC-776 User Manual  
Frequency/ Voltage Control  
Auto Detect DIMM/PCI CLK  
This item allows you to enable/disable auto detect DIMM/PCI  
clock. The choices: Enable/Disable  
Spread Spectrum  
This allows you to enable/disable the spread spectrum modulate.  
When the system clock generator pulses, the extreme values of the  
pulse generate excess EMI. Enabling pulse spectrum spread  
modulation changes the extreme pulse spikes to flat curves thus  
reducing EMI.  
The choices: Enable, Disable  
Clock By Slight Adjust  
This item allows you to select the CPU clock from 166 MHz to  
100 MHz or 99 MHz to 66 MHz depending on the CPU host  
clock.  
CPU Clock Ratio  
This item allows you to select the CPU ratio. When using an Intel  
CPU this item will be hidden.  
Chapter 3 Award BIOS Setup 75  
Load Fail-Safe Defaults  
Load Fail-Safe Defaults  
When you press <Enter> on this item you get a confirmation dialog  
box with a message similar to:  
Load Fail-Safe Default (Y/N)?  
Pressing “Y” loads the BIOS default values for the most stable,  
minimal performance system operations.  
76 SBC-776 User Manual  
Load Optimized Default  
Load Optimized Default  
When you press <Enter> on this item you get a confirmation dialog  
box with a message similar to:  
Load Optimized Defaults (Y/N)?  
Pressing “Y” loads the default values that are factory settings for  
optimal performance system operations  
Chapter 3 Award BIOS Setup 77  
Set Supervisor Password  
When you select this function, a message appears at the center of  
the screen:  
ENTER PASSWORD:  
Type the password, up to eight characters, and press Enter. Typing  
a password clears any previously entered password from CMOS  
memory.  
Now the message changes:  
CONFIRM PASSWORD:  
Again, type the password and press Enter.  
To abort the process at any time, press Esc.  
In the Security Option item in the BIOS Features Setup screen,  
select System or Setup:  
System Enter a password each time the system boots and when  
ever you enter Setup.  
Setup  
Enter a password when ever you enter Setup.  
NOTE: To clear the password, simply press Enter when asked to  
enter a password. Then the password function is disabled.  
78 SBC-776 User Manual  
Set User Password  
When you select this function, a message appears at the center of  
the screen:  
ENTER PASSWORD:  
Type the password, up to eight characters, and press Enter. Typing  
a password clears any previously entered password from CMOS  
memory.  
Now the message changes:  
CONFIRM PASSWORD:  
Again, type the password and press Enter.  
To abort the process at any time, press Esc.  
In the Security Option item in the BIOS Features Setup screen,  
select System or Setup:  
System Enter a password each time the system boots and when  
ever you enter Setup.  
Setup  
Enter a password when ever you enter Setup.  
NOTE: To clear the password, simply press Enter when asked to  
enter a password. Then the password function is disabled.  
Chapter 3 Award BIOS Setup 79  
Save to CMOS and EXIT  
Save to CMOS and EXIT  
Pressing <Enter> on this item asks for confirmation:  
Save to CMOS and Exit (Y/N)?  
Pressing “Y” stores the selections made in the menus in CMOS, a  
special section of memory that stays on after you turn your system  
off. The next time you boot your computer, the BIOS configures  
your system according to the Setup selections stored in CMOS.  
After saving the values the system is restarted again.  
80 SBC-776 User Manual  
Quit without Saving  
Exit Without Saving  
Pressing <Enter> on this item asks for confirmation:  
Quit Without Saving (Y/N)?  
This allows you to exit Setup without storing in CMOS any change.  
The previous selections remain in effect. This exits the Setup  
utility and restarts your computer.  
Chapter 3 Award BIOS Setup 81  
4
DRIVERS INSTALLATION  
This SBC-776 is equipped with an audio,  
VGA and Dual LAN interface. This chapter provides  
instructions for installing the software  
drivers on these pheripherals.  
SBC-776 User Manual  
Installing Drivers  
Notice: Attention  
Please follow this “order of installation” for stable  
and efficient operations.  
1. Software installation utility  
1.1 For WIN95/98/2000/Me  
P.S WIN NT4.0 does not need this driver because it  
can’t support Plug and Play.  
2. Intel 82562ET LAN Driver  
2.1 For WIN98/Me: Intel did not release 82562ET driver  
for WIN95.  
2.2 For WIN2000  
2.3 For WIN NT4.0  
3. Advansys 38C0800 SCSI Driver  
3.1 For WIN95/98/Me  
3.2 For WIN2000  
3.3 For WIN NT4.0  
4. Intel 82559ER:  
4.1 For WIN95/98/2000/Me  
4.2 For WIN NT 4.0  
5. Intel 815E VGA Driver  
5.1 For WIN95/98/Me  
5.2 For WIN2000  
5.3 For WIN NT4.0  
6. Ultra ATA Storage Driver  
6.1 For WIN98/2000/NT4.0  
PS For WIN95: Intel did not release an Ultra ATA  
storage driver for WIN95.  
Notice: Attention  
Chapter 4 Drivers  
Notice: Attention  
7. Advance Logic ALC200 Sound Driver  
7.1 For WIN95  
7.2 For WIN98  
7.3 For WIN Me  
7.4 For WIN2000  
7.5 For Win NT 4.0  
Notice: Attention  
SBC-776 User Manual  
Software Installation Utility  
1.1 For WIN95/98/2000/Me  
~~>Install the CDROM Driver into the CD disk drive.  
~~>Find the Software Installation Utility Folder  
~~>Find the WIN95/95/2000/Me folder  
~~>Find the infinst_enu folder  
~~>Find the disk 1 folder  
~~>Find the setup icon and then double click  
~~>Click on Next  
~~>Click on Yes  
~~>Click on Next, install the utility  
~~>Click on Yes to restart computer now  
~~>Click finish to restart  
Chapter 4 Drivers  
Intel 82562ET LAN Driver  
2.1 & 2.2 Installation Procedures are the same.  
~~>Click on Start button  
~~>Click on Settings button  
~~>Click on Control Panel button  
~~>Click on Systems button  
~~>Click on Device Manager button  
~~>Click on Secondary PCI Ethernet Controller  
~~>Click on Reinstall Driver  
~~>Click on Next  
~~>Select Display a list of the known drivers for this  
device so that I can choose a specific driver  
~~>Click on Next  
~~>Select Network Adapters  
~~>Click on Next  
~~>Click on Have Disk  
~~>Find the 82562ET folder  
~~>Select your OS folder (WIN98/Me or WIN2000  
folder)  
~~>Click on Next  
~~>Appear net82557.inf, click on Open  
~~>Click on OK  
~~>Find Intel PRO/100 VE Network Connection  
~~>Click on Next  
~~>Click on Next, install the driver  
~~>Click on Finish  
~~>Click on Close to finish the 82562ET driver  
installation  
SBC-776 User Manual  
2.3 Installation Procedures for WIN NT4.0  
*Please copy the 82562ET driver from the CDROM  
onto Floppy Disks and insert into floppy drive*  
~~>Click on Start button  
~~>Click on Settings button  
~~>Click on Control Panel button  
~~>Double click on Network  
~~>Click on Yes  
~~>Click on Next  
~~>Click on Select from List........  
~~>Click on Have Disk  
~~>Click on OK  
~~>Click on OK  
~~>Appear Intel Pro Adapter  
~~>Click on OK  
~~>Click on Next  
~~>Select TCP/IP Protocol, NWlink IPX/SPX  
Compatible Transport, NetBEUI Protocol (PS: This  
depends on your system)  
~~>Click on Next  
~~>Click on Next  
~~>Click on Next  
~~>Type the WIN NT4.0 CDROM path (such as E:)  
and then click on continue, setup will continue.  
~~>Appear Do You want to use DHCP? (PS:Depends  
on your system). Click on No.  
~~>Setup your TCP/IP Properties  
~~>Click on Next  
~~>Click on Next  
Chapter 4 Drivers  
~~>Type the Workgroup name, click on Next  
~~>Click on Yes  
~~>Appear Do you want to restart your computer now?  
Click on Yes.  
SBC-776 User Manual  
Advansys 38C0800 SCSI Driver  
3.1 & 3.2 Installation Procedures are identical.  
~~>Place CDROM into CD disk drive  
~~>Click on Start button  
~~>Click on Settings button  
~~>Click on Control Panel button  
~~>Click on Systems button  
~~>Click on Device Manager button  
~~>Click on SCSI Controller  
~~>Click on Reinstall Driver  
~~>Click on Next  
~~>Select Display a list of know drivers for this........  
~~>Select Network Adapters  
~~>Click on Next  
~~>Click on Have Disk  
~~>Find the Advansys folder  
~~>Select your O.S. folder (WIN95/98/ME/2000  
folder)  
~~>Click on Next  
~~>Appear w2kadv.inf, click on open  
~~>Click on OK  
~~>Find Win2k Advansys Ultra 2 Wide SCSI Adapter,  
click on next  
~~>Shows the Update driver warning, click on yes  
~~>Click on Next  
~~>Click on Next  
~~>Click on Finish  
~~>Click on Close to finish the Advansys driver  
installation  
Chapter 4 Drivers  
3.3 Installation procedures for WIN NT 4.0  
~~>Place CDROM into CD disk drive  
~~>Click on Start button  
~~>Click on Settings button  
~~>Click on Control Panel  
~~>Double Click on SCSI Adapter  
~~>Click on Drives  
~~>Click on ADD  
~~>Click on Have Disk  
~~>Click on Browse, find the advansys folder  
~~>Find the WIN NT 4.0 folder, under the name of  
nt4adv.inf  
~~>Click on Open  
~~>Click on OK  
~~>Click on Next  
~~>Select WIN NT 4.0 Advansys Ultra 2 Wide SCSI  
Adapter  
~~>Appear Do you want to restart your computer now?  
Click on yes.  
SBC-776 User Manual  
Intel 82559ER LAN Driver  
4.1 Installation Direction for Intel 82559ER LAN Driver  
~~>Place CDROM into CD disk drive  
~~>Click on Start button  
~~>Click Settings button  
~~>Click on Control Panel button  
~~>Click on System button  
~~>Click on Device Manager button  
~~>Click on PCI Ethernet Controller  
~~>Click on Reinstall Driver  
~~>Click on Next  
~~>Select Display a list of the known drivers for this......  
~~>Click on Next  
~~>Select Network Adapter  
~~>Click on Next  
~~>Click on Have Disk  
~~>Find the 82559ER folder  
~~>Find the Drivers folder  
~~>Find the 82559er drivers 17 folder  
~~>Find the net 82559er.inf, click on Open  
~~>Click on OK  
~~>Find Intel GD82559ER PCI Adapter  
~~>Click on Next  
~~>Click on Next, install the driver  
~~>Click on Yes  
~~>Click on Finish  
~~>Click on Close to finish the 82559ER driver  
installation  
Chapter 4 Drivers  
4.2 Installation procedures for WIN NT 4.0  
*Please copy the 82559ER driver from the CDROM  
onto floppy disk and insert into the floppy drive*  
~~>Place CDROM into CD disk drive  
~~>Click on Start button  
~~>Click on Setting button  
~~>Click on Control Panel button  
~~>Double click on Network  
~~>Click on Adapters  
~~>Click on ADD  
~~>Click on Have Disk  
~~>Click on OK  
~~>Appear Intel 82559ER fast ethernet adapter  
~~>Click on OK to install driver  
~~>Click on Close  
~~>Setup your TCP/IP Properties  
~~>Appear Do you want to restart your computer now?  
Click on Yes.  
SBC-776 User Manual  
Intel 815E VGA Driver  
5.1, 5.2 & 5.3 Installation Procedures  
~~>Place the CDROM into the CD disk drive  
~~>Find the VGA folder  
~~>Select your OS folder (WIN95/98/2000/NT)  
~~>Select Graphic folder  
~~>Select Setup icon, double click  
~~>Click on Next  
~~>Click on Yes, install VGA driver  
~~>Click on finish, restart my computer now  
Chapter 4 Drivers  
Intel Ultra ATA Storage Driver  
6.1 Installation procedures  
~~>Place the CDROM into the CD disk drive  
~~>Find the Ultra ATA driver folder  
~~>Find the intel ATA603_enu icon, double click select  
graphic folder  
~~>Click on Next  
~~>Click on Yes  
~~>Click on Next  
~~>Click on Next  
~~>Select Yes, I want to restart my computer now  
~~>Click on Finish, restart my computer now  
SBC-776 User Manual  
Advance Logic ALC200 Sound Driver  
7.1-7.5 Installation procedures  
~~>Place the CDROM into the CD disk drive  
~~>Click on Advance ALC200 folder  
~~>Select your OS folder (WIN95/98/2000/Me/NT)  
~~>Double click on Setup icon  
~~>You will see an optional language window, select  
English  
~~>Click on Next  
~~>Click on go  
~~>Click on Yes  
~~>Restart my computer now  
Chapter 4 Drivers  

Intel Dh61bf Desktop Motherboard BOXDH61BF User Manual
Intel iEi Motherboard A300 User Manual
JVC AV 21MT16 User Manual
Loewe Centros 1202 User Manual
Motorola MA550 User Manual
NEC 50M User Manual
Omron CP1E NA@@D@ @ User Manual
Philips Computer Monitor 2 34E+07 User Manual
Philips DVD Player DVP620VR User Manual
Philips PET724 User Manual