|
GA-8I865GVMK-775
Intel® Pentium® 4 LGA775 Processor Motherboard
User's Manual
Rev. 1002
12ME-I865GVMKT-1002
Copyright
© 2006 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved.
The trademarks mentioned in the manual are legally registered to their respective companies.
Notice
The written content provided with this product is the property of Gigabyte.
No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any
means without Gigabyte's prior written permission. Specifications and features are subject to
change without prior notice.
Product Manual Classification
In order to assist in the use of this product, Gigabyte has categorized the user manual in the
following:
„
„
For detailed product information and specifications, please carefully read the
"Product User Manual".
For detailed information related to Gigabyte's unique features, please go to "Technology
Guide" section on Gigabyte's website to read or download the information you need.
Table of Contents
GA-8I865GVMK-775 Motherboard Layout ..................................................................... 6
Block Diagram................................................................................................................ 7
Chapter 1 Hardware Installation .................................................................................... 9
1-1 Considerations Prior to Installation .................................................................... 9
1-2 Feature Summary .......................................................................................... 10
1-3 Installation of the CPU and Heatsink ............................................................... 11
1-3-1 Installation of the CPU .......................................................................................... 11
1-3-2 Installation of the Heatsink .................................................................................. 12
1-4 Installation of Memory .................................................................................... 13
1-5 Installation of Expansion Cards ...................................................................... 15
1-6 I/O Back Panel Introduction ........................................................................... 16
1-7 ConnectorsIntroduction .................................................................................. 17
Chapter 2 BIOS Setup................................................................................................ 27
The Main Menu (For example: BIOS Ver. : E1) ....................................................... 28
2-1 Standard CMOS Features ............................................................................. 30
2-2 Advanced BIOS Features .............................................................................. 32
2-3 IntegratedPeripherals ..................................................................................... 34
2-4 Power Management Setup ............................................................................. 37
2-5 PnP/PCI Configurations................................................................................. 38
2-6 PC Health Status ........................................................................................... 39
2-7 Frequency/Voltage Control ............................................................................. 40
2-8 Load Fail-Safe Defaults ................................................................................... 41
2-9 Load Optimized Defaults ................................................................................. 41
2-10 Set Supervisor/User Password ..................................................................... 42
2-11 Save & Exit Setup ......................................................................................... 43
2-12 Exit Without Saving ....................................................................................... 43
- 4 -
Chapter 3 Drivers Installation ...................................................................................... 45
3-1 Install Chipset Drivers .................................................................................... 45
3-2 SoftwareApplication ....................................................................................... 46
3-3 SoftwareInformation ....................................................................................... 46
3-4 Hardware Information ..................................................................................... 47
3-5 Contact Us ..................................................................................................... 47
Chapter 4 Appendix ................................................................................................... 49
4-1 Unique Software Utilities ................................................................................ 49
4-1-1 Xpress Recovery2 Introduction ......................................................................... 49
4-1-2 Flash BIOS Method Introduction ........................................................................ 51
4-1-3 2- / 4- / 5.1- Channel Audio Function Introduction .......................................... 60
4-2 Troubleshooting ............................................................................................... 64
- 5 -
GA-8I865GVMK-775 Motherboard Layout
KB_MS
LGA775
ATX_12V
ATX
CPU_FAN
FDD
R_USB
LPC47M997
Intel 865GV
AUDIO
F_AUDIO
BAT
PCI1
EP82562G
Intel ICH5
BIOS
SATA0
SATA1
PCI2
PCI3
IR
SPDIF
CODEC
PWR_LED
F_PANEL
F_USB1
F_USB2
CD_IN
COMB
- 6 -
Block Diagram
CPUCLK+/-(133/200MHz)
LGA775
Processor
Host
Interface
VGA
DDR 400/333/266MHz DIMM
Dual Channel Memory
HCLK (133/200MHz)
Intel
865GV
GMCH
GMCHCLK (66MHz)
66MHz
33MHz
14.318MHz
48MHz
BIOS
PCI Bus
2 Serial ATA
Intel
ICH5
ATA33/66/100
IDE Channels
EP82562G
Floppy
RJ45
LPT Port
LPC47M997
COM Ports
CODEC
PS/2 KB/Mouse
14.318MHz
8 USB
Ports
3 PCI
33MHz
PCICLK
(33MHz)
- 7 -
- 8 -
Chapter 1Hardware Installation
1-1 Considerations Prior to Installation
Preparing Your Computer
The motherboard contains numerous delicate electronic circuits and components which can
become damaged as a result of electrostatic discharge (ESD). Thus, prior to installation, please
follow the instructions below:
1. Please turn off the computer and unplug its power cord.
2. When handling the motherboard, avoid touching any metal leads or connectors.
3. It is best to wear an electrostatic discharge (ESD) cuff when handling electronic components
(CPU, RAM).
4. Prior to installing the electronic components, please have these items on top of an antistatic
pad or within a electrostatic shielding container.
5. Please verify that the power supply is switched off before unplugging the power supply
connector from the motherboard.
Installation Notices
1. Prior to installation, please do not remove the stickers on the motherboard. These stickers
are required for warranty validation.
2. Prior to the installation of the motherboard or any hardware, please first carefully read the
information in the provided manual.
3. Before using the product, please verify that all cables and power connectors are connected.
4. To prevent damage to the motherboard, please do not allow screws to come in contact with
the motherboard circuit or its components.
5. Please make sure there are no leftover screws or metal components placed on the motherboard
or within the computer casing.
6. Please do not place the computer system on an uneven surface.
7. Turning on the computer power during the installation process can lead to damage to system
components as well as physical harm to the user.
8. If you are uncertain about any installation steps or have a problem related to the use of the
product, please consult a certified computer technician.
Instances of Non-Warranty
1. Damage due to natural disaster, accident or human cause.
2. Damage as a result of violating the conditions recommended in the user manual.
3. Damage due to improper installation.
4. Damage due to use of uncertified components.
5. Damage due to use exceeding the permitted parameters.
6. Product determined to be an unofficial Gigabyte product.
- 9 -
Hardware Installation
1-2 Feature Summary
CPU
Š
Š
Š
Š
Š
Š
Š
Š
Š
Š
Supports the latest Intel® Pentium® 4 LGA775 CPU
Supports 800/533MHz FSB
L2 cache varies with CPU
Northbridge: Intel® 865GV Chipset
Southbridge: Intel® ICH5
4 DDR DIMM memory slots (supports up to 4GB memory) (Note)
Supports dual channel DDR 400/333/266 unbuffered DIMM
Supports 2.5V DDR DIMM
Chipset
Memory
Slots
IDE Connections
3 PCI slots
2 IDE connection (UDMA 33/ATA 66/ATA 100), allows connection of
4 IDE devices
FDD Connections
Onboard SATA
Peripherals
Š
Š
Š
Š
Š
Š
Š
Š
Š
Š
Š
Š
Š
Š
Š
1 FDD connection, allows connection of 2 FDD devices
2 Serial ATA ports from ICH5 controller (SATA0, SATA1)
1 parallel port supporting Normal/EPP/ECP mode
1 VGA port, 1 COMA port, onboard COMB connection
8 USB 2.0/1.1 ports (rear x 4, front x 4 via cable)
1 front audio connector
1 IR connector
1 PS/2 keyboard port
1 PS/2 mouse port
Built-in Intel® 865GV Chipset
Onboard EP82562G chip (10/100 Mbit)
1 RJ45 port
ADI AD1888 CODEC
Supports 2 / 4 / 5.1 channel audio
Supports Line In (Rear Speaker Out) ; Line Out (Front Speaker Out) ;
MIC (Center/Subwoofer Speaker Out)
SPDIF Out connection
CD In connection
SMSC LPC47M997
System voltage detection
Onboard VGA
Onboard LAN
Onboard Audio
Š
Š
Š
Š
Š
Š
Š
Š
Š
Š
I/O Control
Hardware Monitor
CPU / System temperature detection
CPU / System fan speed detection
Use of licensed AWARD BIOS
Supports Q-Flash
Supports @BIOS
BIOS
Additional Features
Form Factor
Micro ATX form factor; 24.4cm x 24.4cm
(Note) Due to standard PC architecture, a certain amount of memory is reserved for system usage and
therefore the actual memory size is less than the stated amount.
For example, 4 GB of memory size will instead be shown as 3.xxGB memory during system startup.
GA-8I865GVMK-775 Motherboard
- 10 -
1-3 Installation of the CPU and Heatsink
Before installing the CPU, please comply with the following conditions:
1. Please make sure that the motherboard supports the CPU.
2. Please take note of the one indented corner of the CPU. If you install the CPU in the wrong
direction, the CPU will not insert properly. If this occurs, please change the insert direction
of the CPU.
3. Please add an even layer of heat sink paste between the CPU and heatsink.
4. Please make sure the heatsink is installed on the CPU prior to system use, otherwise
overheating and permanent damage of the CPU may occur.
5. Please set the CPU host frequency in accordance with the processor specifications. It is not
recommended that the system bus frequency be set beyond hardware specifications since it
does not meet the required standards for the peripherals. If you wish to set the frequency
beyond the proper specifications, please do so according to your hardware specifications
including the CPU, graphics card, memory, hard drive, etc.
HT functionality requirement content :
Enabling the functionality of Hyper-Threading Technology for your computer system requires all
of the following platform components:
- CPU: An Intel® Pentium 4 Processor with HT Technology
- Chipset: An Intel® Chipset that supports HT Technology
- BIOS: A BIOS that supports HT Technology and has it enabled
- OS: An operation system that has optimizations for HT Technology
1-3-1 Installation of the CPU
Fig. 1
Fig. 2
Metal Lever
Gently lift the metal
lever located on the
CPU socket to the
upright position.
Remove the plastic
covering on the CPU
socket.
Fig. 3
Fig. 4
Notice the small gold
colored triangle located
on the edge of the CPU
socket. Align the
Once the CPU is
properly inserted,
please replace the
plastic covering and
push the metal lever
back into its original
position.
indented corner of the
CPU with the triangle and gently insert the CPU into
position. (Grasping the CPU firmly between your
thumb and forefinger, carefully place it into the socket
in a straight and downwards motion. Avoid twisting or
bending motions that might cause damage to the CPU
during installation.)
- 11 -
Hardware Installation
1-3-2 Installation of the Heatsink
Male Push Pin
The top of Female Push Pin
Female Push Pin
Fig.1
Fig. 2
Please apply an even layer of heatsink paste on
the surface of the installed CPU.
(Turning the push pin along the direction of arrow is
to remove the heatsink, on the contrary, is to install.)
Please note the direction of arrow sign on the male
push pin doesn't face inwards before installation. (This
instruction is only for Intel boxed fan)
Fig. 3
Fig. 4
Place the heatsink atop the CPU and make sure
the push pins aim to the pin hole on the
motherboard. Pressing down the push pins
diagonally.
Please make sure the Male and Female push pin are
joined closely. (for detailed installation instructions,
please refer to the heatsink installation section of the
user manual)
Fig. 5
Fig. 6
Please check the back of motherboard after
installing. If the push pin is inserted as the picture,
the installation is complete.
Finally, please attach the power connector of the
heatsink to the CPU fan header located on the
motherboard.
The heatsink may adhere to the CPU as a result of hardening of the heatsink paste. To prevent
such an occurrence, it is suggested that either thermal tape rather than heat sink paste be used for
heat dissipation or using extreme care when removing the heatsink.
GA-8I865GVMK-775 Motherboard
- 12 -
1-4 Installation of Memory
Before installing the memory modules, please comply with the following conditions:
1. Please make sure that the memory used is supported by the motherboard. It is
recommended that memory of similar capacity, specifications and brand be used.
2. Before installing or removing memory modules, please make sure that the computer power
is switched off to prevent hardware damage.
3. Memory modules have a foolproof insertion design. A memory module can be installed in
only one direction. If you are unable to insert the module, please switch the direction.
The motherboard supports DDR memory modules, whereby BIOS will automatically detect memory
capacity and specifications. Memory modules are designed so that they can be inserted only in one direction.
The memory capacity used can differ with each slot.
Notch
DDR
Fig.1
The DIMM socket has a notch, so the DIMM memory module can only
fit in one direction. Insert the DIMM memory module vertically into the
DIMM socket. Then push it down.
Fig.2
Close the plastic clip at both edges of the DIMM sockets to lock the
DIMM module.
Reverse the installation steps when you wish to remove the DIMM
module.
- 13 -
Hardware Installation
Dual Channel DDR
GA-8I865GVMK-775 supports the Dual Channel Technology. After operating the Dual Channel Technology,
the bandwidth of Memory Bus will double.
GA-8I865GVMK-775 includes 4 DIMM sockets, and each Channel has two DIMM sockets as following:
Channel A : DDR 1, DDR 2
Channel B : DDR 3, DDR 4
If you want to operate the Dual Channel Technology, please note the following explanations due to the
limitation of Intel chipset specifications.
1. Dual channel memory cannot be used if one or three DDR memory modules are installed.
2. If two DDR memory modules are installed (same storage capacity), one must be added to the
Channel A slot and the other in the Channel B slot in order to use dual channel memory. Dual
channel memory cannot function if both DDR memory modules are installed on the same channel.
3. If four DDR memory modules are installed, please use memory of the same storage capacity in
order to use dual channel memory and for BIOS to detect all the DDR memory modules.
We'll strongly recommend our user to slot two DDR memory modules into the DIMMs with the same color in
order for Dual Channel Technology to work.
The following table is for Dual Channel Technology combination: (DS: Double Side, SS: Single Side)
DDR 1
DS/SS
X
DDR 2
X
DDR 3
DS/SS
X
DDR 4
X
2 memory modules
4 memory modules
DS/SS
DS/SS
DS/SS
DS/SS
DS/SS
DS/SS
GA-8I865GVMK-775 Motherboard
- 14 -
1-5 Installation of Expansion Cards
You can install your expansion card by following the steps outlined below:
1. Read the related expansion card's instruction document before install the expansion card into the
computer.
2. Remove your computer's chassis cover, screws and slot bracket from the computer.
3. Press the expansion card firmly into expansion slot in motherboard.
4. Be sure the metal contacts on the card are indeed seated in the slot.
5. Replace the screw to secure the slot bracket of the expansion card.
6. Replace your computer's chassis cover.
7. Power on the computer, if necessary, setup BIOS utility of expansion card from BIOS.
8. Install related driver from the operating system.
Installing a PCI expansion card:
- 15 -
Hardware Installation
1-6 I/O Back Panel Introduction
PS/2 Keyboard and PS/2 Mouse Connector
To install a PS/2 port keyboard and mouse, plug the mouse to the upper port (green) and the keyboard to the
lower port (purple).
Parallel Port
The parallel port allows connection of a printer, scanner and other peripheral devices.
COMA (Serial Port)
Connects to serial-based mouse or data processing devices.
VGA Port
Monitor can be connected to VGA port.
USB port
Before you connect your device(s) into USB connector(s), please make sure your device(s) such as
USB keyboard, mouse, scanner, zip, speaker...etc. have a standard USB interface. Also make sure
your OS supports USB controller. If your OS does not support USB controller, please contact OS ven
dor for possible patch or driver upgrade. For more information please contact your OS or device(s)
vendors.
LAN Port
The provided Internet connection provides data transfer speeds of 10/100Mbps.
Line In
Devices like CD-ROM, walkman etc. can be connected to Line In jack.
Line Out
Connect the stereo speakers or earphone to this connector.
MIC In
Microphone can be connected to MIC In jack.
You can use audio software to configure 2-/4-/5.1-channel audio functioning.
GA-8I865GVMK-775 Motherboard
- 16 -
1-7 Connectors Introduction
1
3
2
5
6
9
11
17
4
16
13
7
8
12 15
14
10
1) ATX_12V
10) F_PANEL
11) F_AUDIO
12) CD_IN
2) ATX (Power Connector)
3) CPU_FAN
4) SYS_FAN
5) FDD
13) SPDIF
14) F_USB1 / F_USB2
15) COMB
6) IDE1 / IDE2
7) SATA0 / SATA1
8) PWR_LED
9) BAT
16) IR
17) CLR_CMOS
- 17 -
Hardware Installation
1/2) ATX_12V/ATX (Power Connector)
With the use of the power connector, the power supply can supply enough stable power to all
the components on the motherboard. Before connecting the power connector, please make sure
that all components and devices are properly installed. Align the power connector with its
proper location on the motherboard and connect tightly.
The ATX_12V power connector mainly supplies power to the CPU. If the ATX_12V power
connector is not connected, the system will not start.
Caution!
Please use a power supply that is able to handle the system voltage requirements. It is
recommended that a power supply that can withstand high power consumption be used (300W
or greater). If a power supply is used that does not provide the required power, the result can
lead to an unstable system or a system that is unable to start.
If you use a 24-pin ATX power supply, please remove the small cover on the power connector
on the motherboard before plugging in the power cord ; otherwise, please do not remove it.
4
2
Pin No.
Definition
GND
1
2
3
4
GND
+12V
3
1
+12V
Pin No.
Definition
1
3.3V
13
1
2
3.3V
3
GND
4
+5V
5
GND
6
+5V
7
GND
8
Power Good
9
5V SB(stand by +5V)
10
11
12
+12V
+12V
3.3V
(Only for 24pins ATX)
24
12
13
14
15
16
17
18
19
20
21
22
23
24
3.3V
-12V
GND
PS_ON(soft On/Off)
GND
GND
GND
-5V
+5V
+5V
+5V
GND
GA-8I865GVMK-775 Motherboard
- 18 -
3/4)
CPU_FAN / SYS_FAN (Cooler Fan Power Connector)
The cooler fan power connector supplies a +12V power voltage via a 3-pin/4-pin(only for CPU_FAN)
power connector and possesses a foolproof connection design.
Most coolers are designed with color-coded power connector wires. A red power connector wire
indicates a positive connection and requires a +12V power voltage. The black connector wire is the
ground wire (GND).
Please remember to connect the power to the cooler to prevent system overheating and failure.
Caution!
Please remember to connect the power to the CPU fan to prevent CPU overheating and failure.
Pin No.
Definition
GND
1
1
2
3
4
CPU_FAN
+12V
Sense
Speed Control
(Only for CPU_FAN)
1
SYS_FAN
5) FDD (FDD Connector)
The FDD connector is used to connect the FDD cable while the other end of the cable connects to the
FDD drive. The types of FDD drives supported are: 360KB, 720KB, 1.2MB, 1.44MB and 2.88MB.
Please connect the red power connector wire to the pin1 position.
34
33
2
1
- 19 -
Hardware Installation
6) IDE1 / IDE2 (IDE Connector)
An IDE device connects to the computer via an IDE connector. One IDE connector can connect to one
IDE cable, and the single IDE cable can then connect to two IDE devices (hard drive or optical drive). If
you wish to connect two IDE devices, please set the jumper on one IDE device as Master and the other
as Slave (for information on settings, please refer to the instructions located on the IDE device).
40
39
2
1
7) SATA0 / SATA1 (Serial ATA Connector)
Serial ATA can provide up to 150MB/s transfer rate. Please refer to the BIOS setting for the Serial
ATA and install the proper driver in order to work properly.
Pin No.
Definition
GND
TXP
1
2
3
4
5
6
7
7
1
TXN
GND
RXN
RXP
GND
GA-8I865GVMK-775 Motherboard
- 20 -
8) PWR_LED
PWR_LED is connect with the system power indicator to indicate whether the system is on/off. It will
blink when the system enters suspend mode.
Pin No.
Definition
MPD+
MPD-
1
1
2
3
MPD-
9) BAT(Battery)
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended
by the manufacturer.
Dispose of used batteries according to the manufacturer's
instructions.
If you want to erase CMOS...
1. Turn OFF the computer and unplug the power cord.
2. Take out the battery gently and put it aside for about 10 minutes.
(Or you can use a metal object to connect the positive and nega-
tive pins in the battery holder to makethem short for one
minute.)
3. Re-install the battery.
4. Plug the power cord and turn ON the computer.
- 21 -
Hardware Installation
10) F_PANEL (Front Panel Jumper)
Please connect the power LED, PC speaker, reset switch and power switch etc. of your chassis
frontpanel to the F_PANEL connector according to the pin assignment below.
Speaker Connector
Message LED/
Power
Switch
Power/
Sleep LED
2
1
20
19
Reset Switch
IDE Hard Disk Active LED
HD (IDE Hard Disk Active LED)
SPEAK (Speaker Connector)
Pin 1: LED anode(+)
Pin 2: LED cathode(-)
Pin 1: Power
Pin 2- Pin 3: NC
Pin 4: Data(-)
RES (Reset Switch)
PW (Power Switch)
MSG(Message LED/Power/Sleep LED)
NC
Open:Normal
Close: Reset Hardware System
Open:Normal
Close: Power On/Off
Pin 1: LED anode(+)
Pin 2: LED cathode(-)
NC
GA-8I865GVMK-775 Motherboard
- 22 -
11) F_AUDIO (Front Audio Panel Connector)
If you want to use Front Audio connector, you must remove 5-6, 9-10 Jumper.
In order to utilize the front audio header, your chassis must have front audio connector. Also please
make sure the pin assigment on the cable is the same as the pin assigment on the MB header. To find
out if the chassis you are buying support front audio connector, please contact your dealer. Please note,
you can have the alternative of using front audio connector or of using rear audio connector to play
sound.
Pin No.
Definition
1
2
3
4
5
6
7
8
9
10
MIC
GND
MIC_BIAS
POWER
9
1
2
FrontAudio(R)
Rear Audio (R)/ Return R
NC
10
No Pin
FrontAudio (L)
Rear Audio (L)/ Return L
12) CD_IN (CD In Connector)
Connect CD-ROM or DVD-ROM audio out to the connector.
Pin No.
Definition
CD-L
1
2
3
4
GND
1
GND
CD-R
- 23 -
Hardware Installation
13) SPDIF (SPDIF Out Connector)
The SPDIF output is capable of providing digital audio to external speakers or compressed AC3 data to
an external Dolby Digital Decoder. Use this feature only when your stereo system has digital input
function. Be careful with the polarity of the SPDIF connector. Check the pin assignment carefully while
you connect the SPDIF cable, incorrect connection between the cable and connector will make the
device unable to work or even damage it. For optional SPDIF cable, please contact your local dealer.
Pin No.
Definition
Power
No Pin
SPDIF
NC
1
2
3
4
5
6
2
6
1
5
GND
GND
14) F_ USB1 / F_USB2 (Front USB Connector)
Be careful with the polarity of the front USB connector. Check the pin assignment carefully while you
connect the front USB cable, incorrect connection between the cable and connector will make the
device unable to work or even damage it. For optional front USB cable, please contact your local dealer.
Pin No.
Definition
Power
1
2
3
4
5
6
7
8
9
10
Power
2
1
10
9
USB DX-
USB Dy-
USB DX+
USB Dy+
GND
GND
No Pin
NC
GA-8I865GVMK-775 Motherboard
- 24 -
15) COMB (COM B Connector)
Be careful with the polarity of the COMB connector. Check the pin assignment carefully while you
connect the COMB cable, incorrect connection between the cable and connector will make the device
unable to work or even damage it. For optional COMB cable, please contact your local dealer.
Pin No.
Definition
NDCDB-
NSINB
1
2
3
4
5
6
7
8
9
10
2
1
10
9
NSOUTB
NDTRB-
GND
NDSRB-
NRTSB-
NCTSB-
NRIB-
No Pin
16) IR
Be careful with the polarity of the IR connector while you connect the IR. Please contact your nearest
dealer for optional IR device.
Pin No.
Definition
Power
No Pin
IR RX
GND
1
2
3
4
5
1
IR TX
- 25 -
Hardware Installation
17) CLR_CMOS (Clear CMOS)
You may clear the CMOS data to its default values by this jumper. To clear CMOS, temporarily short
1-2 pin. Default doesn't include the "Shunter" to prevent from improper use this jumper.
Open: Normal
1
Short: Clear CMOS
1
GA-8I865GVMK-775 Motherboard
- 26 -
Chapter 2 BIOS Setup
BIOS (Basic Input and Output System) includes a CMOS SETUP utility which allows user to configure
required settings or to activate certain system features.
The CMOS SETUP saves the configuration in the CMOS SRAM of the motherboard.
When the power is turned off, the battery on the motherboard supplies the necessary power to the CMOS
SRAM.
When the power is turned on, pushing the <Del> button during the BIOS POST (Power-On Self Test) will
take you to the CMOS SETUP screen. You can enter the BIOS setup screen by pressing "Ctrl + F1".
When setting up BIOS for the first time, it is recommended that you save the current BIOS to a disk in the
event that BIOS needs to be reset to its original settings. If you wish to upgrade to a new BIOS, either
Gigabyte's Q-Flash or @BIOS utility can be used.
Q-Flash allows the user to quickly and easily update or backup BIOS without entering the operating system.
@BIOS is a Windows-based utility that does not require users to boot to DOS before upgrading BIOS but
directly download and update BIOS from the Internet.
CONTROL KEYS
<
>< >< ><
>
Move to select item
<Enter>
<Esc>
Select Item
Main Menu - Quit and not save changes into CMOS Status Page Setup Menu
and Option Page Setup Menu - Exit current page and return to Main Menu
Increase the numeric value or make changes
Decrease the numeric value or make changes
General help, only for Status Page Setup Menu and Option Page Setup Menu
Item Help
<Page Up>
<Page Down>
<F1>
<F2>
<F5>
<F6>
<F7>
Restore the previous CMOS value from CMOS, only for Option Page Setup Menu
Load the fail-safe default CMOS value from BIOS default table
Load the Optimized Defaults
<F8>
Q-Flash utility
<F9>
System Information
<F10>
Save all the CMOS changes, only for Main Menu
Main Menu
The on-line description of the highlighted setup function is displayed at the bottom of the screen.
Status Page Setup Menu / Option Page Setup Menu
Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selec-
tions for the highlighted item. To exit the Help Window press <Esc>.
- 27 -
BIOS Setup
The BIOS Setup menus described in this chapter are for reference only and may differ from the
exact settings for your motherboard.
The Main Menu (For example: BIOS Ver. : E1)
Once you enter Award BIOS CMOS Setup Utility, the Main Menu (as figure below) will appear on the
screen. Use arrow keys to select among the items and press <Enter> to accept or enter the sub-menu.
CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
`
`
`
`
`
`
`
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Power Management Setup
PnP/PCI Configurations
PC Health Status
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Save & Exit Setup
Exit Without Saving
Frequency/Voltage Control
ESC: Quit
KLJI: Select Item
F8: Q-Flash
F10: Save & Exit Setup
Time, Date, Hard Disk Type...
If you can't find the setting you want, please press "Ctrl+F1" to search the advanced option hidden.
„
„
„
„
„
„
„
„
Standard CMOS Features
This setup page includes all the items in standard compatible BIOS.
Advanced BIOS Features
This setup page includes all the items of Award special enhanced features.
Integrated Peripherals
This setup page includes all onboard peripherals.
Power Management Setup
This setup page includes all the items of Green function features.
PnP/PCI Configuration
This setup page includes all the configurations of PCI & PnP ISA resources.
PC Health Status
This setup page is the System auto detect Temperature, voltage, fan, speed.
Frequency/Voltage Control
This setup page is control CPU clock and frequency ratio.
Load Fail-Safe Defaults
Fail-Safe Defaults indicates the value of the system parameters which the system would be in safe
configuration.
GA-8I865GVMK-775 Motherboard
- 28 -
„
Load Optimized Defaults
Optimized Defaults indicates the value of the system parameters which the system would be in best
performance configuration.
„
„
„
„
Set Supervisor Password
Change, set, or disable password. It allows you to limit access to the system and Setup, or just to Setup.
Set User Password
Change, set, or disable password. It allows you to limit access to the system.
Save & Exit Setup
Save CMOS value settings to CMOS and exit setup.
Exit Without Saving
Abandon all CMOS value changes and exit setup.
- 29 -
BIOS Setup
2-1 Standard CMOS Features
CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
Standard CMOS Features
Date (mm:dd:yy)
Time (hh:mm:ss)
Thu, Aug
22:31:24
5
2004
Item Help
Menu Level`
`
`
`
`
IDE Channel 0 Master
IDE Channel 0 Slave
IDE Channel 1 Master
IDE Channel 1 Slave
[None]
[None]
[None]
[None]
Change the day, month,
year
<Week>
Sun. to Sat.
Drive A
Drive B
[1.44M, 3.5"]
[None]
<Month>
Floppy 3 Mode Support
[Disabled]
Jan. to Dec.
Halt On
[All, But Keyboard]
<Day>
1 to 31 (or maximum
allowed in the month)
Base Memory
Extended Memory
Total Memory
640K
239M
240M
<Year>
1999 to 2098
KLJI: Move
Enter: Select
+/-/PU/PD: Value
F6: Fail-Safe Defaults
F10: Save
ESC: Exit
F7: Optimized Defaults
F1: General Help
F5: Previous Values
Date
The date format is <week>, <month>, <day>, <year>.
Week
Month
Day
The week, from Sun to Sat, determined by the BIOS and is display only
The month, Jan. Through Dec.
The day, from 1 to 31 (or the maximum allowed in the month)
The year, from 1999 through 2098
Year
Time
The times format in <hour> <minute> <second>. The time is calculated base on the 24-hour military-
time clock. For example, 1 p.m. is 13:00:00.
IDE Channel 0 Master, Slave / IDE Channel 1 Master, Slave
IDE HDD Auto-Detection Press "Enter" to select this option for automatic device detection.
IDE Channel 0/1 Master/Slave IDE Device Setup. You can use one of three methods:
Auto
None
Allows BIOS to automatically detect IDE devices during POST. (Default value)
Select this if no IDE devices are used and the system will skip the automatic
detection step and allow for faster system start up.
Manual
User can manually input the correct settings.
Access Mode Use this to set the access mode for the hard drive. The four options are:
CHS/LBA/Large/Auto(default:Auto)
Hard drive information should be labeled on the outside drive casing. Enter the appropriate option
based on this information.
Cylinder
Head
Number of cylinders
Number of heads
Write precomp
Precomp
Landing Zone Landing zone
Sector
Number of sectors
If a hard disk has not been installed, select NONE and press <Enter>.
GA-8I865GVMK-775 Motherboard
- 30 -
Drive A / Drive B
The category identifies the types of floppy disk drive A or drive B that has been installed in the computer.
None
No floppy drive installed
360K, 5.25"
1.2M, 5.25"
5.25 inch PC-type standard drive; 360K byte capacity.
5.25 inch AT-type high-density drive; 1.2M byte capacity
(3.5 inch when 3 Mode is Enabled).
720K, 3.5"
1.44M, 3.5"
2.88M, 3.5"
3.5 inch double-sided drive; 720K byte capacity
3.5 inch double-sided drive; 1.44M byte capacity.
3.5 inch double-sided drive; 2.88M byte capacity.
Floppy 3 Mode Support (for Japan Area)
Disabled
Drive A
Drive B
Both
Normal Floppy Drive. (Default value)
Drive A is 3 mode Floppy Drive.
Drive B is 3 mode Floppy Drive.
Drive A & B are 3 mode Floppy Drives.
Halt on
The category determines whether the computer will stop if an error is detected during power up.
No Errors
The system boot will not stop for any error that may be detected and you
will be prompted.
All Errors
Whenever the BIOS detects a non-fatal error the system will be stopped.
All, But Keyboard The system boot will not stop for a keyboard error; it will stop for all other
errors. (Default value)
All, But Diskette
All, But Disk/Key
The system boot will not stop for a disk error; it will stop for all other errors.
The system boot will not stop for a keyboard or disk error; it will stop for all
other errors.
Memory
The category is display-only which is determined by POST (Power On Self Test) of the BIOS.
Base Memory
The POST of the BIOS will determine the amount of base (or conventional) memory installed in the
system.
The value of the base memory is typically 512K for systems with 512K memory installed on the
motherboard, or 640K for systems with 640K or more memory installed on the motherboard.
Extended Memory
The BIOS determines how much extended memory is present during the POST.
This is the amount of memory located above 1 MB in the CPU's memory address map.
Total Memory
This item displays the memory size that used.
- 31 -
BIOS Setup
2-2 Advanced BIOS Features
CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
Advanced BIOS Features
`
Hard Disk Boot Priority
First Boot Device
[Press Enter]
[Floppy]
Item Help
Menu Level`
Second Boot Device
Third Boot Device
Password Check
[Hard Disk]
[CDROM]
[Setup]
Select Hard Disk Boot
Device Priority
#
CPU Hyper-Threading
[Enabled]
[Disabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[16MB]
Limit CPUID Max. to 3
No-Execute Memory Protect (Note)
CPU Enhanced Halt (C1E) (Note)
CPU Thermal Monitor 2(TM2) (Note)
CPU EIST Function (Note)
On-Chip Frame Buffer Size
KLJI: Move
Enter: Select
+/-/PU/PD: Value
F6: Fail-Safe Defaults
F10: Save
ESC: Exit
F7: Optimized Defaults
F1: General Help
F5: Previous Values
" # " System will detect automatically and show up when you install the Intel® Pentium® 4
processor with HT Technology.
Hard Disk Boot Priority
Select boot sequence for onboard(or add-on cards) SCSI, RAID, etc.
Use < > or < > to select a device, then press<+> to move it up, or <-> to move it down the list. Press
<ESC> to exit this menu.
First / Second / Third Boot Device
Floppy
LS120
Hard Disk
CDROM
ZIP
Select your boot device priority by Floppy.
Select your boot device priority by LS120.
Select your boot device priority by Hard Disk.
Select your boot device priority by CDROM.
Select your boot device priority by ZIP.
USB-FDD
USB-ZIP
USB-CDROM
USB-HDD
LAN
Select your boot device priority by USB-FDD.
Select your boot device priority by USB-ZIP.
Select your boot device priority by USB-CDROM.
Select your boot device priority by USB-HDD.
Select your boot device priority by LAN.
Disabled
Select your boot device priority by Disabled.
Password Check
Setup
The system will boot but will not access to Setup page if the correct
password is not entered at the prompt. (Default value)
The system will not boot and will not access to Setup page if the correct
password is not entered at the prompt.
System
(Note) This item will show up when you install a processor that supports this function.
GA-8I865GVMK-775 Motherboard - 32 -
CPU Hyper-Threading
Enabled
Enables CPU Hyper-Threading Feature. Please note that this feature is only
working for operating system with multi processors mode supported. (Default
value)
Disabled
Disables CPU Hyper-Threading.
Limit CPUID Max. to 3
Enabled
Limit CPUID Maximum value to 3 when use older OS like NT4.
Disabled
Disables CPUID Limit for Windows XP.(Default value)
No-Execute Memory Protect(Note)
Enabled
Enable No-Execute Memory Protect function.(Default value)
Disabled
Disable No-Execute Memory Protect function.
CPU Enhanced Halt (C1E)(Note)
Enabled
Enable CPU Enhanced Halt (C1E) function.(Default value)
Disabled
Disable CPU Enhanced Halt (C1E) function.
CPU Thermal Monitor 2 (TM2) (Note)
Enabled
Enable CPU Thermal Monitor 2 (TM2) function.(Default value)
Disabled
Disable CPU Thermal Monitor 2 (TM2) function.
CPU EIST Function (Note)
Enabled
Enable CPU EIST function.(Default value)
Disabled
Disable CPU EIST function.
On-Chip Frame Buffer Size
1MB
Set on-chip frame buffer size to 1MB.
4MB
Set on-chip frame buffer size to 4MB.
8MB
Set on-chip frame buffer size to 8MB.
16MB
32MB
Set on-chip frame buffer size to 16MB. (Default value)
Set on-chip frame buffer size to 32MB.
(Note) This item will show up when you install a processor that supports this function.
- 33 -
BIOS Setup
2-3 Integrated Peripherals
CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
Integrated Peripherals
On-Chip Primary PCI IDE
On-Chip Secondary PCI IDE
On-Chip SATA
[Enabled]
[Enabled]
[Auto]
Item Help
Menu Level`
x
SATA Port0 configure as
SATA Port1 configure as
USB Controller
USB 2.0 Controller
USB Keyboard Support
USB Mouse Support
AC97 Audio
SATA Port0
SATA Port1
[Enabled]
[Enabled]
[Disabled]
[Disabled]
[Auto]
Onboard H/W LAN
Onboard LAN Boot ROM
POWER ON Function
Onboard Serial Port 1
Onboard Serial Port 2
UART Mode Select
UR2 Duplex Mode
Onboard Parallel Port
Parallel Port Mode
ECP Mode Use DMA
[Enabled]
[Disabled]
[Disabled]
[3F8/IRQ4]
[2F8/IRQ3]
[Normal]
Half
[378/IRQ7]
[PRINTER]
3
x
x
KLJI: Move
Enter: Select
+/-/PU/PD: Value
F6: Fail-Safe Defaults
F10: Save
ESC: Exit
F7: Optimized Defaults
F1: General Help
F5: Previous Values
On-Chip Primary PCI IDE
Enabled
Enable onboard 1st channel IDE port. (Default value)
Disabled
Disable onboard 1st channel IDE port.
On-Chip Secondary PCI IDE
Enabled
Enable onboard 2nd channel IDE port. (Default value)
Disabled
Disable onboard 2nd channel IDE port.
On-Chip SATA
Disabled
Disable onboard Seria ATA function.
Auto
When there is no device to be plugged in IDE1 or IDE2, SATA controller will
remap to IDE controller. (Default value)
Manual
Set SATA mode manually from "SATA Port0 configure as" item.
SATA Port0 configure as
IDE Pri. Master
IDE Pri. Slave
IDE Sec. Master
IDE Sec. Slave
SATA Port0
Set SATA controller to compatible mode. This mode will remap SATA Port 0 to
IDE Primary Master.
Set SATA controller to compatible mode. This mode will remap SATA Port 0 to
IDE Primary Slave.
Set SATA controller to compatible mode. This mode will remap SATA Port 0 to
IDE Secondary Master.
Set SATA controller to compatible mode. This mode will remap SATA Port 0 to
IDE Secondary Slave.
Set SATA controller to native mode(Serial ATA mode - SATA Port 0). This mode
is only supported by Windows XP or later. (Default value)
Set SATA controller to native mode(Serial ATA mode - SATA Port 1). This mode
is only supported by Windows XP or later.
SATA Port1
SATA Port1 configure as
The setting depends on "SATA Port0 configure as" item setting. (Default: SATA Port1)
GA-8I865GVMK-775 Motherboard
- 34 -
USB Controller
Enabled
Disabled
Enable USB controller. (Default value)
Disable USB controller.
USB 2.0 Controller
You can disable this function if you are not using onboard USB 2.0 feature.
Enabled
Disabled
Enable USB 2.0 controller. (Default value)
Disable USB 2.0 controller.
USB Keyboard Support
Enabled
Enable USB keyboard support.
Disabled
Disable USB keyboard support. (Default value)
USB Mouse Support
Enabled
Enable USB mouse support.
Disabled
Disable USB mouse support. (Default value)
AC97 Audio
Auto
Disabled
Auto detect AC97 audio function. (Default value)
Disable AC97 audio function.
Onboard H/W LAN
Enabled
Disabled
Enable onboard H/W LAN function. (Default value)
Disable this function.
Onboard LAN Boot ROM
This function decide whether to invoke the boot ROM of the onboard LAN chip.
Enabled
Disabled
Enable this function.
Disable this function. (Default value)
POWER ON Function
Disabled
Any KEY
Mouse
Disable this function. (Default value)
Press any key to power on the system.
Double click on mouse left button to power on the system.
Mouse/Any KEY Press any key or double click on mouse left button to power on the system.
Onboard Serial Port 1
Auto
BIOS will automatically setup the port 1 address.
3F8/IRQ4
2F8/IRQ3
3E8/IRQ4
2E8/IRQ3
Disabled
Enable onboard Serial port 1 and address is 3F8/IRQ4. (Default value)
Enable onboard Serial port 1 and address is 2F8/IRQ3.
Enable onboard Serial port 1 and address is 3E8/IRQ4.
Enable onboard Serial port 1 and address is 2E8/IRQ3.
Disable onboard Serial port 1.
Onboard Serial Port 2
Auto
BIOS will automatically setup the port 1 address.
3F8/IRQ4
2F8/IRQ3
3E8/IRQ4
2E8/IRQ3
Disabled
Enable onboard Serial port 2 and address is 3F8/IRQ4.
Enable onboard Serial port 2 and address is 2F8/IRQ3. (Default value)
Enable onboard Serial port 2 and address is 3E8/IRQ4.
Enable onboard Serial port 2 and address is 2E8/IRQ3.
Disable onboard Serial port 2.
- 35 -
BIOS Setup
UART Mode Select
This item allows you to determine which Infra Red(IR) function of Onboard I/O chip.
Normal
IrDA
Set onboard I/O chip UART to normal mode. (Default value)
Set onboard I/O chip UART to IrDA mode.
ASKIR
Set onboard I/O chip UART to ASKIR mode.
UR2 Duplex Mode
This feature allows you to seclect IR mode.
This function will available when "UART Mode Select" doesn't set at Normal.
Half
Full
IR Function Duplex Half. (Default value)
IR Function Duplex Full.
Onboard Parallel port
Disabled
Disable onboard LPT port.
378/IRQ7
278/IRQ5
Enable onboard LPT port and address is 378/IRQ7. (Default value)
Enable onboard LPT port and address is 278/IRQ5.
3BC/IRQ7
Parallel Port Mode
SPP
Enable onboard LPT port and address is 3BC/IRQ7.
Using Parallel port as Standard Parallel Port.
EPP1.9+SPP
ECP
Using Parallel port as Enhanced Parallel Port 1.9 and SPP mode.
Using Parallel port as Extended Capabilities Port.
EPP1.9+ECP
PRINTER
EPP1.7+SPP
EPP1.7+ECP
ECP Mode Use DMA
3
Using Parallel port as Enhanced Parallel Port 1.9 and ECP mode.
Using Parallel port as printer port. (Default value)
Using Parallel port as Enhanced Parallel Port 1.7 and SPP mode.
Using Parallel port as Enhanced Parallel Port 1.7 and ECP mode.
Set ECP Mode Use DMA to 3. (Default value)
Set ECP Mode Use DMA to 1.
1
GA-8I865GVMK-775 Motherboard
- 36 -
2-4 Power Management Setup
CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
Power Management Setup
ACPI Suspend Type
Power LED in S1 state
Off by Power button
AC BACK Function
PME Event Wake Up
ModemRingOn/WakeOnLan
Resume by Alarm
[S1(POS)]
[Blinking]
[Instant-off]
[Soft-Off]
[Enabled]
[Enabled]
[Disabled]
Everday
Item Help
Menu Level`
x
x
Date (of Month) Alarm
Time (hh:mm:ss) Alarm
0 : 0 : 0
KLJI: Move
Enter: Select
+/-/PU/PD: Value
F6: Fail-Safe Defaults
F10: Save
ESC: Exit
F7: Optimized Defaults
F1: General Help
F5: Previous Values
ACPI Suspend Type
S1(POS)
Set ACPI suspend type to S1/POS(Power On Suspend). (Default value)
S3(STR)
Set ACPI suspend type to S3/STR(Suspend To RAM).
Power LED in S1 state
Blinking
In standby mode(S1), poer LED will blink. (Default value)
Dual/OFF
In standby mode(S1):
a. If use single color LED, power LED will turn off.
b. If use dual color LED, power LED will turn to another color.
Off by Power button
Instant-off
Press power button then Power off instantly. (Default value)
Delay 4 Sec. Press power button 4 sec. to Power off. Enter suspend if button is pressed less than
4 seconds.
AC BACK Function
Soft-Off
When AC-power back to the system, the system will be in "Off" state.
(Default value)
Full-On
Memory
When AC-power back to the system, the system always in "On" state.
When AC-power back to the system, the system will return to the Last state
before AC-power off.
PME Event Wake Up
This feature requires an ATX power supply that provides at least 1A on the 5VSB lead.
Disabled
Enabled
Disable this function.
Enable PME as wake up event. (Default value)
ModemRingOn/WakeOnLan
An incoming call via modem can awake the system from any suspend state or an input signal comes
from the other client server on the LAN can awake the system from any suspend state.
Disabled
Enabled
Disable Modem Ring On / Wake On LAN function.
Enable Modem Ring On / Wake On LAN function. (Default value)
- 37 -
BIOS Setup
Resume by Alarm
You can set "Resume by Alarm" item to enabled and key in Date/Time to power on system.
Disabled
Enabled
Disable this function. (Default value)
Enable alarm function to POWER ON system.
If Resume by Alarm is Enabled.
Date (of Month) Alarm :
Everyday, 1~31
Time (hh: mm: ss) Alarm :
(0~23) : (0~59) : (0~59)
2-5 PnP/PCI Configurations
CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
PnP/PCI Configurations
PCI 1 IRQ Assignment
PCI 2 IRQ Assignment
PCI 3 IRQ Assignment
[Auto]
[Auto]
[Auto]
Item Help
Menu Level`
Device(s) using this
INT:
KLJI: Move
Enter: Select
+/-/PU/PD: Value
F6: Fail-Safe Defaults
F10: Save
ESC: Exit
F7: Optimized Defaults
F1: General Help
F5: Previous Values
PCI 1 IRQ Assignment
Auto
3,4,5,7,9,10,11,12,14,15
Auto assign IRQ to PCI 1. (Default value)
Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 1.
PCI 2 IRQ Assignment
Auto
3,4,5,7,9,10,11,12,14,15
Auto assign IRQ to PCI 2. (Default value)
Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 2.
PCI 3 IRQ Assignment
Auto
3,4,5,7,9,10,11,12,14,15
Auto assign IRQ to PCI 3. (Default value)
Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 3.
GA-8I865GVMK-775 Motherboard
- 38 -
2-6 PC Health Status
CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
PC Health Status
Current CPU Temperature
Current System Temperature
Vcore
+3.3V
+5V
+12V
DDR25V
Current CPU FAN Speed
Current SYSTEM FAN Speed
CPU Smart FAN Control
CPU Smart FAN Mode
50oC
Item Help
Menu Level`
32oC
1.35V
3.28V
5.17V
11.84V
2.39V
3308 RPM
0
RPM
[Enabled]
[Auto]
KLJI: Move
Enter: Select
+/-/PU/PD: Value
F6: Fail-Safe Defaults
F10: Save
ESC: Exit
F7: Optimized Defaults
F1: General Help
F5: Previous Values
Current CPU/System Temperature
Detect CPU/System temperature automatically.
Current Voltage(V) Vcore / +3.3V / +5V / +12V / DDR25V
Detect system's voltage status automatically.
Current CPU/SYSTEM FAN Speed (RPM)
Detect CPU/SYSTEM Fan speed status automatically.
CPU Smart FAN Control
Disabled Disable this function.
Enabled When this function is enabled, CPU fan will run at different speed depending on
CPU temperature. Users can adjust the fan speed with Easy Tune based on
their requirements. (Default value)
CPU Smart FAN Mode
This option is available only when CPU Smart FAN Control is enabled.
Auto
BIOS autodetects the type of CPU fan you installed and sets the optimal CPU Smart
FAN control mode for it. (Default value)
Voltage Set to Voltage when you use a CPU fan with a 3-pin fan power cable.
PWM Set to PWM when you use a CPU fan with a 4-pin fan power cable.
In fact, the Voltage option can be used for CPU fans with 3-pin or 4-pin power cables.
However, some 4-pin CPU fan power cables are not designed following Intel 4-wire fans
PWM control specifications. With such CPU fans, selecting PWM will not effectively reduce
the fan speed.
- 39 -
BIOS Setup
2-7 Frequency/Voltage Control
CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
Frequency/Voltage Control
CPU Clock Ratio
Memory Frequency For
Memory Frequency (Mhz)
[15X]
[Auto]
266
Item Help
Menu Level`
Set CPU Ratio if CPU
Ratio is unclocked
KLJI: Move
Enter: Select
+/-/PU/PD: Value
F6: Fail-Safe Defaults
F10: Save
ESC: Exit
F7: Optimized Defaults
F1: General Help
F5: Previous Values
Incorrect using these features may cause your system broken. For power end-user use only.
CPU Clock Ratio
This setup option will automatically assign by CPU detection.
The option will display "Locked" and read only if the CPU ratio is not changeable.
Memory Frequency For
Wrong frequency may make system can't boot, clear CMOS to overcome wrong frequency issue.
for FSB(Front Side Bus) frequency=533MHz,
2.0
Memory Frequency = Host clock x 2.
2.5
Memory Frequency = Host clock x 2.5.
Auto
Set Memory frequency by DRAM SPD data. (Default value)
for FSB(Front Side Bus) frequency=800MHz,
1.33
1.66
2.0
Memory Frequency = Host clock x 1.33.
Memory Frequency = Host clock x 1.66.
Memory Frequency = Host clock x 2.
Auto
Set Memory frequency by DRAM SPD data. (Default value)
Memory Frequency (Mhz)
The values depend on "Memory Frequency For" item.
GA-8I865GVMK-775 Motherboard
- 40 -
2-8 Load Fail-Safe Defaults
CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
`
`
`
`
`
`
`
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Power Management Setup
PnP/PCI C
PC Health Status
Load Fail-Safe Defaults (Y/N)? N
Exit Without Saving
MB Intelligent Tweaker(M.I.T.)
ESC: Quit
KLJI: Select Item
F8: Q-Flash
F10: Save & Exit Setup
Load Fail-Safe Defaults
Fail-Safe defaults contain the most appropriate values of the system parameters that allow minimum system
performance.
2-9 Load Optimized Defaults
CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
`
`
`
`
`
`
`
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Power Management Setup
PnP/PCI C
PC Health Status
Load Optimized Defaults (Y/N)? N
Exit Without Saving
MB Intelligent Tweaker(M.I.T.)
ESC: Quit
KLJI: Select Item
F8: Q-Flash
F10: Save & Exit Setup
Load Optimized Defaults
Selecting this field loads the factory defaults for BIOS and Chipset Features which the system automatically
detects.
- 41 -
BIOS Setup
2-10 Set Supervisor/User Password
CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
`
`
`
`
`
`
`
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Power Management Setup
PnP/PCI C
Enter Password:
PC Health tt
t iai
MB Intelligent Tweaker(M.I.T.)
ESC: Quit
KLJI: Select Item
F8: Q-Flash
F10: Save & Exit Setup
Change/Set/Disable Password
When you select this function, the following message will appear at the center of the screen to assist
you in creating a password.
Type the password, up to eight characters, and press <Enter>. You will be asked to confirm the password.
Type the password again and press <Enter>. You may also press <Esc> to abort the selection and not enter
a password.
To disable password, just press <Enter> when you are prompted to enter password. A message
"PASSWORD DISABLED" will appear to confirm the password being disabled. Once the password is disabled,
the system will boot and you can enter Setup freely.
The BIOS Setup program allows you to specify two separate passwords:
SUPERVISOR PASSWORD and a USER PASSWORD. When disabled, anyone may access all BIOS Setup
program function. When enabled, the Supervisor password is required for entering the BIOS Setup program
and having full configuration fields, the User password is required to access only basic items.
If you select "System" at "Password Check" in Advance BIOS Features Menu, you will be prompted for the
password every time the system is rebooted or any time you try to enter Setup Menu.
If you select "Setup" at "Password Check" in Advance BIOS Features Menu, you will be prompted only when
you try to enter Setup.
GA-8I865GVMK-775 Motherboard
- 42 -
2-11 Save & Exit Setup
CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
`
`
`
`
`
`
`
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Power Management Setup
PnP/PCI Configurations
PC Health
Save & Exit Setup
Save to CMOS and EXIT (Y/N)? Y
MB Intelligent Tweaker(M.I.T.)
ESC: Quit
KLJI: Select Item
F8: Q-Flash
F10: Save & Exit Setup
Save Data to CMOS
Type "Y" will quit the Setup Utility and save the user setup value to RTC CMOS.
Type "N" will return to Setup Utility.
2-12 Exit Without Saving
CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
`
`
`
`
`
`
`
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Power Management Setup
PnP/PCI C
PC Health Status
Quit Without Saving (Y/N)? N
Exit Without Saving
MB Intelligent Tweaker(M.I.T.)
ESC: Quit
KLJI: Select Item
F8: Q-Flash
F10: Save & Exit Setup
Abandon all Data
Type "Y" will quit the Setup Utility without saving to RTC CMOS.
Type "N" will return to Setup Utility.
- 43 -
BIOS Setup
GA-8I865GVMK-775 Motherboard
- 44 -
Chapter 3Drivers Installation
Pictures below are shown in Windows XP.
Insert the driver CD-title that came with your motherboard into your CD-ROM drive, the driver
CD-title will auto start and show the installation guide. If not, please double click the CD-ROM
device icon in "My computer", and execute the Run.exe.
3-1 Install Chipset Drivers
After insert the driver CD, "Xpress Install" will scan automatically the system and then list all the drivers that
recommended to install. The "Xpress Install" uses the"Click and Go" technology to install the drivers
automatically. Just select the drivers you want then click the "GO" button. The will execute the installation for
you automatically.
Some device drivers will restart your system automatically. After restarting your system the "Xpress
Install" will continue to install other drivers.
System will reboot automatically after install the drivers, afterward you can install others application.
For USB2.0 driver support under Windows XP operating system, please use Windows Service
Pack. After install Windows Service Pack, it will show a question mark "?" in "Universal Serial Bus
controller" under "Device Manager". Please remove the question mark and restart the system
(System will auto-detect the right USB2.0 driver).
- 45 -
Drivers Installation
3-2 Software Application
This page displays all the tools that Gigabyte developed and some free software, you can choose anyone
you want and press "install" to install them.
3-3 Software Information
This page lists the contents of software and drivers in this CD-title.
GA-8I865GVMK-775 Motherboard
- 46 -
3-4 Hardware Information
This page lists all device you have for this motherboard.
3-5 Contact Us
Please see the last page for details.
- 47 -
Drivers Installation
GA-8I865GVMK-775 Motherboard
- 48 -
Chapter 4 Appendix
4-1 Unique Software Utilities
4-1-1 Xpress Recovery2 Introduction
Xpress Recovery2 is designed to provide quick backup and restora-
tion of hard disk data. Supporting Microsoft operating systems including
Windows XP/2000/NT/98/Me and DOS, and file systems including
FAT16, FAT32, and NTFS, Xpress Recovery2 is able to back up data
on hard disks on PATA and SATA IDE controllers. After Xpress Recovery2 is executed from CD-ROM
for the first time, it will stay permanent in your hard disk. If you wish to run Xpress Recovery2 later, you
can simply press F9 during system bootup to enter Xpress Recovery2 without the CD-ROM.
System requirements:
1. Intel x86 platforms
2. At least 64M bytes of system memory
3. VESA-supported VGA cards
How to use the Xpress Recovery2
Initial access by booting from CD-ROM and subsequent access by pressing the F9 key:
Steps: After entering BIOS Setup, go to Advanced BIOS Feature and set to boot from CD-ROM. Save
the settings and exit the BIOS Setup. Insert the provided driver CD into your CD-ROM drive. Upon
system restart, the message which says "Boot from CD/DVD:" will appear in the bottom left corner
of the screen. Press any key to enter Xpress Recovery2.
After the steps above are completed, subsequent access to Xpress Recovery2 can be made
by simply pressing the <F9> key during system power-on.
.
.
Boot from CD/DVD:
Press any key to startup XpressRecovery2.....
Boot from CD/DVD:
Award Modular BIOS v6.00PG, An Energy Star Ally
Copyright (C) 1984-2005, Award Software, Inc.
Intel 865 BIOS for 8I865GVMK-775 F4
.
.
.
.
<DEL>:BIOS Setup/Q-Flash, <F9>: Xpress Recovery2, <F12>For Boot Menu
11/07/2005-I865-6A79HG0GC-00
<F9> Xpress Recovery2
1. If you have already entered Xpress Recovery2 by booting from the CD-ROM, you can
enter Xpress Recovery2 by pressing the <F9> key in the future.
2. System storage capacity and the reading/writing speed of the hard disk will affect
the data backup speed.
3. It is recommended that Xpress Recovery2 be immediately installed once you com-
plete installations of OS and all required drivers as well as software.
- 49 -
Appendix
The Main Screen of Xpress Recovery2
1. RESTORE:
Restore the backed-up data to your hard disk.
(This button will not appear if there is no backup
file.)
2. BACKUP:
Back up data from hard disk.
3. REMOVE:
Remove previously-created backup files
to release disk space.
(This button will not appear if there is no backup
file.)
4. REBOOT:
Exit the main screen and restart the system.
Limitations:
1. Not compatible to Xpress Recovery.
2. For the use of Xpress Recovery2, a primary partition must be reserved.
3. Xpress Recovery2 will store the backup file at the end of the hard disk, so free space available
on the hard disk for the backup file must be allocated in advance. (A minimum 4GB is recom-
mended but the actual space is dependent on the size of the data to be backed up)
4. Capable of backing up hard disks installed with Windows operating systems including DOS and
Windows XP/2000/NT/9x/Me.
5. USB hard disks are currently not supported.
6. Does not support RAID/AHCI (class code 0104/0106) hard disks.
7. Capable of backing up and restoring only the first physical hard disk.
Hard disks detection sequence is as follows:
a. PATA IDE primary channel
b. PATA IDE secondary channel
c. SATA IDE channel 1
d. SATA IDE channel 2
e. SATA IDE channel 3
f. SATA IDE channel 4
Precautions:
1. When using hard disks with more than 128G under Windows 2000, be sure to execute the
EnableBigLba.exe program from the driver CD before data backup.
2. It is normal that data backup takes longer time than data restoration.
3. Xpress Recovery2 is compliant with the GPL regulations.
4. On a few motherboards based on Nvidia chipsets, BIOS update is required for Xpress Recovery2
to correctly identify RAID and SATA IDE mode. Please contact your motherboard manufacturer.
5. Xpress Recovery2 supports only PATA hard disks and not SATA hard disks on the following
motherboards (As this is a BIOS-related issue, it can be solved by BIOS update)
GA-K8NXP-9
GA-8N-SLI Royal
GA-8N-SLI Pro
GA-8N-SLI
GA-K8U
GA-K8U-9
GA-K8NXP-SLI
GA-K8N Ultra-SLI
GA-K8N Pro-SLI
GA-K8N Ultra-9
GA-K8NF-9 (PCB Ver. 1.0)
GA-K8NE (PCB Ver. 1.0)
GA-K8NMF-9
GA-8I865GVMK-775 Motherboard
- 50 -
4-1-2 Flash BIOS Method Introduction
Method 1 : Q-FlashTM Utility
Q-FlashTM is a BIOS flash utility embedded in Flash ROM. With this utility,
users only have to stay in the BIOS menu when they want to update
BIOS. Q-FlashTM allows users to flash BIOS without any utility in DOS or
Windows. Using Q-FlashTM indicating no more fooling around with any complicated instructions and
operating system since it is in the BIOS menu.
Please note that because updating BIOS has potential risk, please do it with caution!! We are
sorry that Gigabyte Technology Co., Ltd is not responsible for damages of system because of
incorrect manipulation of updating BIOS to avoid any claims from end-users.
Before You Begin:
Before you start updating BIOS with the Q-FlashTM utility, please follow the steps below first.
1. Download the latest BIOS for your motherboard from Gigabyte's website.
2. Extract the BIOS file downloaded and save the BIOS file (the one with model name.Fxx. For example,
8KNXPU.Fba) to a floppy disk.
3. Reboot your PC and press Del to enter BIOS menu.
The BIOS upgrading guides below are separated into two parts.
If your motherboard has dual-BIOS, please refer to Part One.
If your motherboard has single-BIOS, please refer to Part Two.
Part One:
Updating BIOS with Q-FlashTM Utility on Dual BIOS Motherboards.
Some of Gigabyte motherboards are equipped with dual BIOS. In the BIOS menu of the motherboards
supporting Q-Flash and Dual BIOS, the Q-Flash utility and Dual BIOS utility are combined in the same
screen. This section only deals with how to use Q-Flash utility.
In the following sections, we take GA-8KNXP Ultra as the example to guide you how to flash BIOS
from an older version to the latest version. For example, from Fa3 to Fba.
Award Modular BIOS v6.00PG, An Energy Star Ally
Copyright (C) 1984-2003, Award Software, Inc.
Intel i875P AGPset BIOS for 8KNXP Ultra Fa3
Check System Health OK , VCore = 1.5250
Main Processor : Intel Pentium(R) 4 1.6GHz (133x12)
<CPUID : 0F27 Patch ID : 0027>
The BIOS file is Fa3
before updating
Memory Testing : 131072K OK
Memory Frequency 266 MHz in Single Channel
Primary Master : FUJITSU MPE3170AT ED-03-08
Primary Slave : None
Secondary Master : CREATIVEDVD-RM DVD1242E BC101
Secondary Slave : None
Press DEL to enter SETUP / Dual BIOS / Q-Flash / F9 For
Xpress Recovery
08/07/2003-i875P-6A79BG03C-00
- 51 -
Appendix
Entering the Q-FlashTM utility:
Step1: To use Q-Flash utility, you must press Del in the boot screen to enter BIOS menu.
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Select Language
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Power Management Setup
PnP/PCI Configurations
PC Health Status
Save & Exit Setup
MB Intelligent Tweaker(M.I.T.)
Exit Without Saving
ESC: Quit
F3: Change Language
F10: Save & Exit Setup
F8: Dual BIOS/Q-Flash
Time, Date, Hard Disk Type...
Step 2: Press F8 button on your keyboard and then Y button to enter the Dual BIOS/Q-Flash utility.
Exploring the Q-FlashTM / Dual BIOS utility screen
The Q-Flash / Dual BIOS utility screen consists of the following key components.
Dual BIOS Utility
Dual BIOS utility bar
Boot From.........................................
Main Bios
Main ROM Type/Size.............................SST 49LF003A
Backup ROM Type/Size.........................SST 49LF003A
512K
512K
Task menu for
Dual BIOS
utility
Wide Range Protection Disable
Boot From Main Bios
Auto Recovery Enable
Halt On Error Disable
Copy Main ROM Data to Backup
Load Default Settings
Save Settings to CMOS
Q-FlashTM utility title
bar
Q-Flash Utility
Load Main BIOS from Floppy
Load Backup BIOS from Floppy
Save Main BIOS to Floppy
Save Backup BIOS to Floppy
Task menu for
Q-FlashTM utility
Enter : Run
ꢁꢂ:Move
ESC:Reset
F10:Power Off
Action bar
Task menu for Dual BIOS utility:
Contains the names of eight tasks and two item showing information about the BIOS ROM type. Blocking a
task and pressing Enter key on your keyboard to enable execution of the task.
Task menu for Q-Flash utility:
Contains the names of four tasks. Blocking a task and pressing Enter key on your keyboard to enable execu-
tion of the task.
Action bar:
Contains the names of four actions needed to operate the Q-Flash/Dual BIOS utility. Pressing the buttons
mentioned on your keyboards to perform these actions.
GA-8I865GVMK-775 Motherboard
- 52 -
Using the Q-FlashTM utility:
This section tells you how to update BIOS using the Q-Flash utility. As described in the "Before you begin"
section above, you must prepare a floppy disk having the BIOS file for your motherboard and insert it to your
computer. If you have already put the floppy disk into your system and have entered the Q-Flash utility,
please follow the steps below to flash BIOS.
Steps:
1. Press arrow buttons on your keyboard to move the light bar to "Load Main BIOS from Floppy" item in
the Q-Flash menu and press Enter button.
Later, you will see a box pop up showing the BIOS files you previously downloaded to the floppy disk.
If you want to save the current BIOS for backup purpose, you can begin Step 1 with "Save Main
BIOS to Floppy" item.
2. Move to the BIOS file you want to flash and press Enter.
In this example, we only download one BIOS file to the floppy disk so only one BIOS file,
8KNXPU.Fba, is listed.
Please confirm again you have the correct BIOS file for your motherboard.
Dual BIOS Utility
Boot From.........................................
Main Bios
Main ROM Type/Size.............................SST 49LF003A
Backup ROM Type/Size.........................SST 49LF003A
512K
512K
Wide Range Protection Disable
1 file(s) found
Boo
8KNXPU.Fba
512K
BIOS file in the floppy
disk.
Total size : 1.39M
Free size : 911.50K
DEL : Delete
F5 : Refresh
Save Settings to CMOS
Q-Flash Utility
Load Main BIOS from Floppy
Load Backup BIOS from Floppy
Save Main BIOS to Floppy
Save Backup BIOS to Floppy
Enter : Run
ꢁꢂ:Move
ESC:Reset
F10:Power Off
After pressing Enter, you'll then see the progress of reading the BIOS file from the floppy disk.
Dual BIOS Utility
Boot From.........................................
Main Bios
Main ROM Type/Size.............................SST 49LF003A
Backup ROM Type/Size.........................SST 49LF003A
512K
512K
Wide Range Protection Disable
Reading BIOS file from floppy ...
Don't Turn Off Power or Reset System
Do not trun off power or
reset your system at this
stage!!
>>>>>>>>>>>>>>.....................
Save Settings to CMOS
Q-Flash Utility
Load Main BIOS from Floppy
Load Backup BIOS from Floppy
Save Main BIOS to Floppy
Save Backup BIOS to Floppy
Enter : Run
ꢁꢂ:Move
ESC:Reset
F10:Power Off
After BIOS file is read, you'll see a confirmation dialog box asking you "Are you sure to update BIOS?"
- 53 - Appendix
3. Press Y button on your keyboard after you are sure to update BIOS.
Then it will begin to update BIOS. The progress of updating BIOS will be displayed.
Please do not take out the floppy disk when it begins flashing BIOS.
4. Press any keys to return to the Q-Flash menu when the BIOS updating procedure is completed.
Dual BIOS Utility
Boot From.........................................
Main Bios
Main ROM Type/Size.............................SST 49LF003A
Backup ROM Type/Size.........................SST 49LF003A
512K
512K
Wide Range Protection Disable
You can repeat Step 1 to
4 to flash the backup
BIOS, too.
!! Copy BIOS completed - Pass !!
Please press any key to continue
Save Settings to CMOS
Q-Flash Utility
Load Main BIOS from Floppy
Load Backup BIOS from Floppy
Save Main BIOS to Floppy
Save Backup BIOS to Floppy
Enter : Run
ꢁꢂ:Move
ESC:Reset
F10:Power Off
5. Press Esc and then Y button to exit the Q-Flash utility. The computer will restart automatically after
you exit Q-Flash.
Dual BIOS Utility
Boot From.........................................
Main Bios
Main ROM Type/Size.............................SST 49LF003A
Backup ROM Type/Size.........................SST 49LF003A
512K
512K
Wide Range Protection Disable
Are you sure to RESET ?
[Enter] to continure or [Esc] to abort...
Save Settings to CMOS
Q-Flash Utility
Load Main BIOS from Floppy
Load Backup BIOS from Floppy
Save Main BIOS to Floppy
Save Backup BIOS to Floppy
Enter : Run
ꢁꢂ:Move
ESC:Reset
F10:Power Off
After system reboots, you may find the BIOS version on your boot screen becomes the one you flashed.
Award Modular BIOS v6.00PG, An Energy Star Ally
Copyright (C) 1984-2003, Award Software, Inc.
Intel i875P AGPset BIOS for 8KNXP Ultra Fba
The BIOS file
Check System Health OK , VCore = 1.5250
Main Processor : Intel Pentium(R) 4 1.6GHz (133x12)
<CPUID : 0F27 Patch ID : 0027>
becomes Fab after
Memory Testing : 131072K OK
updating.
Memory Frequency 266 MHz in Single Channel
Primary Master : FUJITSU MPE3170AT ED-03-08
Primary Slave : None
Secondary Master : CREATIVEDVD-RM DVD1242E BC101
Secondary Slave : None
Press DEL to enter SETUP / Dual BIOS / Q-Flash / F9 For Xpress Recovery
09/23/2003-i875P-6A79BG03C-00
GA-8I865GVMK-775 Motherboard
- 54 -
6. Press Del to enter BIOS menu after system reboots. When you are in BIOS menu, move to
Load Fail-Safe Defaults item and press Enter to load BIOS Fail-Safe Defaults. Normally the system
redetects all devices after BIOS has been upgraded. Therefore, we highly recommend reloading the
BIOS defaults after BIOS has been upgraded.
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Select Language
Load Fail-Safe Defaults
Load Optimized Defaults
Power Manag
PnP/PCI Coni
PC Health Status
Load Fail-Safe Defaults (Y/N)? Y
Save & Exit Setup
Exit Without Saving
MB Intelligent Tweaker(M.I.T.)
ESC: Quit
F3: Change Language
F10: Save & Exit Setup
F8: Dual BIOS/Q-Flash
Time, Date, Hard Disk Type...
Press Y on your keyboard to load defaults.
7. Select Save & Exit Setup item to save the settings to CMOS and exit the BIOS menu.
System will reboot after you exit the BIOS menu. The procedure is completed.
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Select Language
Load Fail-Safe Defaults
Load Optimized Defaults
Power Manag
PnP/PCI Con
PC Health Status
Save to CMOS and EXIT (Y/N)? Y
Save & Exit Setup
Exit Without Saving
MB Intelligent Tweaker(M.I.T.)
ESC: Quit
F3: Change Language
F10: Save & Exit Setup
F8: Dual BIOS/Q-Flash
Time, Date, Hard Disk Type...
Press Y on your keyboard to save and exit.
Part Two:
Updating BIOS with Q-FlashTM Utility on Single-BIOS Motherboards.
This part guides users of single-BIOS motherboards how to update BIOS using the Q-FlashTM utility.
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Top Performance
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Power Management Setup
PnP/PCI Configurations
PC Health Status
Save & Exit Setup
MB Intelligent Tweaker(M.I.T.)
Exit Without Saving
ESC: Quit
F3: Change Language
F10: Save & Exit Setup
F8: Q-Flash
Time, Date, Hard Disk Type...
- 55 -
Appendix
Exploring the Q-FlashTM utility screen
The Q-FlashBIOS utility screen consists of the following key components.
Q-FlashTM utility bar
Q-Flash Utility V1.30
Flash Type/Size.................................SST 49LF003A
256K
Keep DMI Data Enable
Task menu for
Q-FlashTM utility
Update BIOS from Floppy
Save BIOS to Floppy
Enter : Run
ꢁꢂ:Move
ESC:Reset
F10:Power Off
Action bar
Task menu for Q-Flash utility:
Contains the names of three tasks. Blocking a task and pressing Enter key on your keyboard to enable
execution of the task.
Action bar:
Contains the names of four actions needed to operate the Q-Flash utility. Pressing the buttons mentioned on
your keyboards to perform these actions.
Using the Q-FlashTM utility:
This section tells you how to update BIOS using the Q-Flash utility. As described in the "Before you begin"
section above, you must prepare a floppy disk having the BIOS file for your motherboard and insert it to your
computer. If you have already put the floppy disk into your system and have entered the Q-Flash utility,
please follow the steps below to flash BIOS.
Steps:
1. Press arrow buttons on your keyboard to move the light bar to "Update BIOS from Floppy" item in the
Q-Flash menu and press Enter button.
Later, you will see a box pop up showing the BIOS files you previously downloaded to the floppy disk.
If you want to save the current BIOS for backup purpose, you can begin Step 1 with "Save BIOS
to Floppy" item.
2. Move to the BIOS file you want to flash and press Enter.
In this example, we only download one BIOS file to the floppy disk so only one BIOS file,
8GE800.F4, is listed.
Please confirm again you have the correct BIOS file for your motherboard.
Q-Flash Utility V1.30
Flash Type/Size.................................SST 49LF003A
256K
1 file(s) found
8GE800.F4
256K
BIOS file in the floppy
disk.
Total size : 1.39M
En
Free size : 1.14M
DEL : Delete
er Off
F5 : Refresh
Q-Flash Utility V1.30
Flash Type/Size.................................SST 49LF003A
256K
Do not trun off power or
reset your system at
this stage!!
Reading BIOS file from floppy ...
>>>>>>>>>>>>>>.....................
En
er Off
Don't Turn Off Power or Reset System
After BIOS file is read, you'll see a confirmation dialog box asking you "Are you sure to update BIOS?"
Please do not take out the floppy disk when it begins flashing BIOS.
GA-8I865GVMK-775 Motherboard
- 56 -
3. Press Y button on your keyboard after you are sure to update BIOS.
Then it will begin to update BIOS. The progress of updating BIOS will be shown at the same time.
Q-Flash Utility V1.30
Flash Type/Size.................................SST 49LF003A
256K
Updating BIOS Now
Do not trun off power or
reset your system
at this stage!!
>>>>>>>>>>>>>>>>>>>.........................
En
er Off
Don't Turn Off Power or Reset System
4. Press any keys to return to the Q-Flash menu when the BIOS updating procedure is completed.
Q-Flash Utility V1.30
Flash Type/Size.................................SST 49LF003A
256K
!! Copy BIOS completed - Pass !!
Please press any key to continue
En
er Off
5. Press Esc and then Y button to exit the Q-Flash utility. The computer will restart automatically after
you exit Q-Flash.
Q-Flash Utility V1.30
Flash Type/Size.................................SST 49LF003A
256K
Are you sure to RESET ?
[Enter] to continure or [Esc] to abort...
En
er Off
After system reboots, you may find the BIOS version on your boot screen becomes the one you flashed.
Award Modular BIOS v6.00PG, An Energy Star Ally
Copyright (C) 1984-2003, Award Software, Inc.
Intel 845GE AGPSet BIOS for 8GE800 F4
The BIOS file
Check System Health OK
Main Processor : Intel Pentium(R) 4 1.7GHz (100x17.0)
<CPUID : 0F0A Patch ID : 0009>
Memory Testing : 122880K OK + 8192K Shared Memory
becomes F4 after
updating
Primary Master : FUJITSU MPE3170AT ED-03-08
Primary Slave : None
Secondary Master : CREATIVEDVD-RM DVD1242E BC101
Secondary Slave : None
Press DEL to enter SETUP / Q-Flash
03/18/2003-I845GE-6A69YG01C-00
6. Press Del to enter BIOS menu after system reboots and "Load BIOS Fail-Safe Defaults". See how
to Load BIOS Fail-Safe Defaults, please kindly refer to Step 6 to 7 in Part One.
Congratulation!! You have updated BIOS successfully!!
- 57 -
Appendix
Method 2 : @BIOSTM Utility
If you do not have a DOS startup disk, we recommend that you use the
new @BIOS utility. @BIOS allows users to update their BIOS under
Windows. Just select the desired @BIOS server to download the latest
version of BIOS.
Fig 1. Installing the @BIOS utility
Fig 2. Installation complete and run @BIOS
Click Sart/ Programs/ GIGABYTE/@BIOS
Select @BIOS item.
Fig 3. The @BIOS utility
Fig 4. Select the desired @BIOS server
Click "ꢀ"
Click "Update New BIOS"
1. Methods and steps:
I. Update BIOS through Internet
a. Click "Internet Update" icon
b. Click "Update New BIOS" icon
c. Select @BIOSTM sever
d. Select the exact model name on your motherboard
e. System will automatically download and update the BIOS.
II. Update BIOS NOT through Internet:
a. Do not click "Internet Update" icon
b. Click "Update New BIOS"
c. Please select "All Files" in dialog box while opening the old file.
d. Please search for BIOS unzip file, downloading from internet or any other methods (such as:
8I865GVM-775.E2).
e. Complete update process following the instruction.
GA-8I865GVMK-775 Motherboard
- 58 -
III. Save BIOS
In the very beginning, there is "Save Current BIOS" icon shown in dialog box. It means to save the
current BIOS version.
IV. Check out supported motherboard and Flash ROM:
In the very beginning, there is "About this program" icon shown in dialog box. It can help you check out
which kind of motherboard and which brand of Flash ROM are supported.
2. Note:
I. In method I, if it shows two or more motherboard's model names to be selected, please make
sure your motherboard's model name again. Selecting wrong model name will cause the
system unbooted.
II. In method II, be sure that motherboard's model name in BIOS unzip file are the same as your
motherboard's. Otherwise, your system won't boot.
III. In method I, if the BIOS file you need cannot be found in @BIOSTM server, please go onto
Gigabyte's web site for downloading and updating it according to method II.
IV. Please note that any interruption during updating will cause system unbooted
- 59 -
Appendix
4-1-3 2- / 4- / 5.1- Channel Audio Function Introduction
You are able to use 2-/4-/5.1-channnels audio feature by audio software selection.
The installation of audio software for Windows 98/ 2000/ ME/ XP is very simple. Please follow the steps to
install the function. (Following pictures are in Windows XP)
Stereo Speakers Connection and Settings:
We recommend that you use the speaker with amplifier to acquire the best sound effect if the stereo output
is applied.
STEP 1:
Connect the stereo speakers or earphone to "Line
Out".
Line Out
STEP 2 :
After you install the audio driver, you will find the
"SoundMAX Control Panel" icon
in the status area
on the lower right of the screen. Right-click the icon
to select "SoundMAX Control Panel" or "Preferences".
STEP 3:
On the "Preferences" menu, click the "Listening
Environment" tab. In the "Speaker Setup" box, click
"Stereo Headphones" or "Stereo Speakers" and then
click "Apply". You will find a headphone or stereo
speakers icon on the SoundMAX menu. This com-
pletes the headphone or stereo speakers setup.
GA-8I865GVMK-775 Motherboard
- 60 -
4 Channel Audio Setup
STEP 1 :
Connect the Front Speakers to "Line Out", the Rear
Speakers to "Line In".
Line In (Rear Speaker Out)
Line Out (Front Speaker Out)
Mic In
STEP 2 :
After you install the audio driver, you will find the
"SoundMAX Control Panel" icon
in the status area
on the lower right of the screen. Right-click the icon
to select "SoundMAX Control Panel" or "Preferences".
STEP 3:
On the "Preferences" menu, click the "Listening
Environment" tab. In the "Speaker Setup" box, click
"Multi-drive" and then click "Apply". You will find a
multi-driver icon on the SoundMAX menu. This com-
pletes the 4-channel audio configuration.
- 61 -
Appendix
5.1 Channel Audio Setup
STEP 1 :
Connect the Front Speakers to "Line Out", the Sur-
round Speakers to "Line In", and the Center/
Subwoofer Speakers to "MIC In".
Line In (Surround Speaker Out)
Line Out (Front Speaker Out)
Mic In (Center/Subwoofer Speaker Out)
STEP 2 :
After you install the audio driver, you will find the
"SoundMAX Control Panel" icon
in the status area
on the lower right of the screen. Right-click the icon
to select "SoundMAX Control Panel" or "Preferences".
STEP 3:
On the "Preferences" menu, click the "Listening
Environment" tab. In the "Speaker Setup" box, click
"Surround Sound Speakers (5.1 Surround)" and then
click "Apply". You will find a surround sound speakers
icon on the SoundMAX menu. This completes the 5.1
channel audio configuration.
Sound Effect Configuration:
At the "Acoustic Environments" menu, users can
adjust sound option settings as desired.
GA-8I865GVMK-775 Motherboard
- 62 -
SPDIF Output Device (Optional Device)
A "S/PDIF output" device is available on the
motherboard. Cable with rear bracket is provided and
could link to the "S/PDIF output" connector (As
picture.) For the further linkage to decoder, rear
bracket provides coaxial cable and Fiber connecting
port.
1.
Connect the SPDIF output device to the rear bracket
of PC, and fix it with screw.
2.
Connect SPDIF wire to the motherboard.
3.
Connect co-axial or optical output to the AC3 decoder.
- 63 -
Appendix
4-2 Troubleshooting
Below is a collection of general asked questions. To check general asked questions based on a specific
Question 1: I cannot see some options that were included in previous BIOS after updating BIOS. Why?
Answer: Some advanced options are hidden in new BIOS version. Please press Ctrl and F1 keys after
entering BIOS menu and you will be able to see these options.
Questions 2: Why is the light of my keyboard/optical mouse still on after computer shuts down?
Answer: In some boards, a small amount of electricity is kept on standby after computer shuts down
and that's why the light is still on.
Question 3: How do I clear CMOS?
Answer: If your board has a Clear CMOS jumper, please refer to the Clear CMOS steps in the manual.
If your board doesn't have such jumper, you can take off the on-board battery to leak voltage to clear
CMOS. Please refer to the steps below:
Steps:
1. Turn off power.
2. Disconnect the power cord from MB.
3. Take out the battery gently and put it aside for about 10 minutes (Or you can use a metal object
to connect the positive and negative pins in the battery holder to makethem short for one
minute).
4. Re-insert the battery to the battery holder.
5. Connect power cord to MB again and turn on power.
6. Press Del to enter BIOS and load Fail-Safe Defaults(or load Optimized Defaults).
7. Save changes and reboot the system.
Question 4: Why do I still get a weak sound after turning up the speaker to the maximum volume?
Answer: Please make sure the speaker you are using is equipped with an internal amplifier. If not,
please change another speaker with power/amplifier and try again later.
Question 5: Sometimes I hear different continuous beeps from computer after system boots up. What do
these beeps usually stand for?
Answer: The beep codes below may help you identify the possible computer problems. However,
they are only for reference purposes. The situations might differ from case to case.
ꢃAMI BIOS Beep Codes
Computer gives 1 short beep when system boots successfully.
*Except for beep code 8, these codes are always fatal.
1 beep Refresh failure
ꢃ
AWARD BIOS Beep Codes
1 short: System boots successfully
2 short: CMOS setting error
1 long 1 short: DRAM or M/B error
1 long 2 short: Monitor or display card
error
1 long 3 short: Keyboard error
1 long 9 short: BIOS ROM error
Continuous long beeps: DRAM error
Continuous short beeps: Power error
*
2 beeps Parity error
3 beeps Base 64K memory failure
4 beeps Timer not operational
5 beeps Processor error
6 beeps 8042 - gate A20 failure
7 beeps Processor exception interrupt error
8 beeps Display memory read/write failure
9 beeps ROM checksum error
10 beeps CMOS shutdown register read/write error
11 beeps Cache memory bad
GA-8I865GVMK-775 Motherboard
- 64 -
- 65 -
Appendix
GA-8I865GVMK-775 Motherboard
- 66 -
- 67 -
Appendix
GA-8I865GVMK-775 Motherboard
- 68 -
- 69 -
Appendix
GA-8I865GVMK-775 Motherboard
- 70 -
Contact Us
ꢁ
Taiwan (Headquarters)
ꢁ
Japan
GIGA-BYTE TECHNOLOGY CO., LTD.
Address: No.6, Bau Chiang Road, Hsin-Tien, Taipei 231,
Taiwan
NIPPON GIGA-BYTE CORPORATION
ꢁ
Singapore
TEL:+886-2-8912-4888
GIGA-BYTE SINGAPORE PTE. LTD.
Tech. Support :
FAX:+886-2-8912-4003
Tech. Support :
Non-Tech. Support(Sales/Marketing) :
Non-Tech. Support(Sales/Marketing) :
ꢁ
U.K.
G.B.T. TECH. CO., LTD.
ꢁ
U.S.A.
Tech. Support :
G.B.T. INC.
Non-Tech. Support(Sales/Marketing) :
TEL:+1-626-854-9338
FAX:+1-626-854-9339
Tech. Support :
Non-Tech. Support(Sales/Marketing) :
ꢁ
The Netherlands
GIGA-BYTE TECHNOLOGY B.V.
Tech. Support :
Non-Tech. Support(Sales/Marketing) :
ꢁ
Germany
G.B.T. TECHNOLOGY TRADING GMBH
Tech. Support :
Non-Tech. Support(Sales/Marketing) :
- 71 -
Appendix
ꢁ
China
ꢁ
Russia
NINGBO G.B.T. TECH. TRADING CO., LTD.
Tech. Support :
Moscow Representative Office Of GIGA-BYTE Technology Co.,
Ltd.
Non-Tech. Support(Sales/Marketing) :
Shanghai
Tech. Support :
Non-Tech. Support(Sales/Marketing) :
TEL:+86-021-63410999
FAX:+86-021-63410100
Beijing
ꢁ
Poland
Office of GIGA-BYTE TECHNOLOGY Co., Ltd. in POLAND
Tech. Support :
TEL:+86-10-62102838
FAX: +86-10-62102848
Wuhan
Non-Tech. Support(Sales/Marketing) :
TEL:+86-27-87851061
FAX: +86-27-87851330
GuangZhou
ꢁ
Serbia & Montenegro
Representative Office Of GIGA-BYTE Technology Co., Ltd. in
SERBIA & MONTENEGRO
TEL:+86-20-87586074
FAX: +86-20-85517843
Chengdu
Tech. Support :
Non-Tech. Support(Sales/Marketing) :
TEL:+86-28-85236930
FAX: +86-28-85256822
Xian
ꢁ
Czech Republic
TEL:+86-29-85531943
FAX: +86-29-85539821
Shenyang
Representative Office Of GIGA-BYTE Technology Co., Ltd. in
CZECHREPUBLIC
Tech. Support :
TEL:+86-24-23960918
FAX:+86-24-23960918-809
Non-Tech. Support(Sales/Marketing) :
ꢁ
Australia
GIGABYTE TECHNOLOGY PTY. LTD.
Tech. Support :
ꢁ
Romania
Non-Tech. Support(Sales/Marketing) :
Representative Office Of GIGA-BYTE Technology Co., Ltd. in
Romania
Tech. Support :
Non-Tech. Support(Sales/Marketing) :
ꢁ
France
GIGABYTE TECHNOLOGY FRANCE S.A.R.L.
Tech. Support :
Non-Tech. Support(Sales/Marketing) :
GA-8I865GVMK-775 Motherboard
- 72 -
|
IBM 31P6260 User Manual
Indesit P 640 TC IX User Manual
KitchenAid KECC568MBB00 User Manual
Konftel 300W User Manual
Moen CRT Television L3175 User Manual
Motorola 68HC08LD User Manual
Philips 27PS55S User Manual
Philips 28GR9670 User Manual
Philips 170B5CS User Manual
Philips SACD900A User Manual