®
Intel Desktop Board
D865GBF/D865GLC
Product Guide
Order Number: C24485-001
Preface
This Product Guide gives information about board layout, component installation, BIOS Setup
menus, and regulatory requirements for Intel® Desktop Board D865GBF/D865GLC.
Intended Audience
The Product Guide is intended for technically qualified personnel. It is not intended for general
audiences.
Information Layout
The chapters in this Product Guide are arranged as follows:
•
•
desktop board and other hardware components.
•
•
•
•
•
Conventions
The following conventions are used in this manual:
WARNING
Warnings indicate conditions that, if not observed, can cause personal injury.
CAUTION
Cautions warn the user about how to prevent damage to hardware or loss of data.
NOTE
Notes call attention to important information.
iii
Intel Desktop Boards D865GBF/D865GLC Product Guide
Terminology
The table below gives descriptions to some common terms used in the product guide.
Term
GB
Description
Gigabyte (1,073,741,824 bytes)
Gigahertz (one billion hertz)
Kilobyte (1024 bytes)
GHz
KB
MB
Megabyte (1,048,576 bytes)
Megabit (1,048,576 bits)
Megahertz (one million hertz)
Mbit
MHz
Box Contents
•
•
•
•
•
•
•
•
•
Intel Desktop Board
I/O shield
One ATA66/100 IDE cable
One ATA33 IDE cable
One SATA cable
One diskette drive cable
Quick Reference Guide
Configuration and battery caution statement label
Intel® Express Installer CD-ROM
iv
Contents
1 Desktop Board Features
Processor............................................................................................................................14
Intel® 865G Chipset.............................................................................................................16
LAN Subsystem (Optional)..................................................................................................17
LAN Subsystem Software...........................................................................................17
RJ-45 LAN Connector LEDs.......................................................................................18
Accelerated Graphics Port (AGP)........................................................................................19
PCI Auto Configuration...............................................................................................19
IDE Auto Configuration...............................................................................................19
Security Passwords....................................................................................................20
ACPI...........................................................................................................................20
Power Connectors......................................................................................................20
Fan Connectors..........................................................................................................21
Suspend to RAM (Instantly Available PC Technology)................................................21
2 Installing and Replacing Desktop Board Components
Installation Instructions........................................................................................................26
Chassis and Component Certifications.......................................................................27
Prevent Power Supply Overload.................................................................................27
v
Intel Desktop Boards D865GBF/D865GLC Product Guide
Installing and Removing the Desktop Board........................................................................29
Installing the Processor Fan Heat Sink.......................................................................30
Connecting the Processor Fan Heat Sink Cable.........................................................31
Installing DIMMs.........................................................................................................33
Removing DIMMs.......................................................................................................34
Connecting the IDE Cable...................................................................................................36
Connecting the Serial ATA Cable........................................................................................37
Connecting Internal Headers...............................................................................................38
Connecting the Chassis Intrusion Cable.....................................................................43
Replacing the Battery..........................................................................................................46
Updating the BIOS with the Intel® Express BIOS Update Utility...........................................49
Recovering the BIOS..................................................................................................51
Peripheral Configuration Submenu.............................................................................59
PATA and SATA Submenus.......................................................................................62
Video Configuration Submenu....................................................................................66
vi
Contents
Chipset Configuration Submenu.................................................................................68
Power Menu........................................................................................................................73
Boot Device Priority Submenu....................................................................................76
Exit Menu............................................................................................................................80
Audio Connectors.......................................................................................................83
Interrupts ....................................................................................................................86
BIOS Beep Codes...............................................................................................................87
BIOS Error Messages..........................................................................................................88
Product Certification Markings.............................................................................................92
1. Desktop Board D865GBF Components ........................................................................12
2. Location of Standby Power Indicator.............................................................................22
3. Installing the I/O Shield.................................................................................................28
4. Location of Desktop Board Mounting Screw Holes........................................................29
5. Installing a Processor....................................................................................................30
7. Installing a Memory Module ..........................................................................................32
8. Dual Configuration Example with Two DIMMs ..............................................................33
9. Dual Configuration Example with Four DIMMs..............................................................33
15. Location of Hardware Control Headers and Power Connectors ....................................42
vii
Intel Desktop Boards D865GBF/D865GLC Product Guide
19. Audio Connectors .........................................................................................................83
20. PCI Bus Add-in Card and Peripheral Interface Connectors...........................................84
1. Desktop Board Differences ............................................................................................ 9
2. Feature Summary.......................................................................................................... 9
3. Manufacturing Options..................................................................................................11
4. Desktop Board Components.........................................................................................13
5. Supported Processors ..................................................................................................14
6. RJ-45 10/100 Ethernet LAN Connector LEDs ...............................................................18
7. RJ-45 10/100/1000 Gigabit Ethernet LAN Connector LEDs ..........................................18
8. Front Panel Audio Header Signal Names (J9A2) ..........................................................39
9. USB 2.0 Headers (J9F1 and J9H1)...............................................................................41
12. BIOS Setup Program Menu Bar....................................................................................53
13. BIOS Setup Program Function Keys.............................................................................54
14. Maintenance Menu .......................................................................................................54
15. Main Menu....................................................................................................................55
16. Advanced Menu............................................................................................................56
18. Boot Configuration Submenu........................................................................................58
25. USB Configuration Submenu........................................................................................67
28. Hardware Monitoring Submenu.....................................................................................71
31. ACPI Submenu.............................................................................................................74
34. Hard Disk Drives Submenu...........................................................................................77
35. Removable Devices Submenu......................................................................................78
38. System Memory Map....................................................................................................85
40. Interrupts ......................................................................................................................86
41. Beep Codes..................................................................................................................87
42. BIOS Error Messages...................................................................................................88
43. Safety Regulations........................................................................................................91
44. EMC Regulations..........................................................................................................91
viii
1 Desktop Board Features
shows the differences between Desktop Boards D865GBF and D865GLC.
Table 1.
Desktop Board Differences
Desktop Board D865GBF
Feature
Desktop Board D865GLC
microATX at 9.6-inches by 9.6-inches
Three
Form factor
ATX at 9.6-inches by 12.0-inches
Six
PCI bus add-in card
connectors
Table 2 describes the major features of Desktop Board D865GBF/D865GLC.
Table 2.
Feature Summary
Support for:
• Intel® Pentium® 4 processor (1.60a, 1.80a, 2a, 2.20 GHz or higher) with 800/533/400
MHz front side bus (FSB) frequency in the mPGA478-pin package
• Intel® Celeron processor (2 GHz or higher) with 400 MHz FSB frequency in the
mPGA478-pin package
• Four 184-pin, 2.5 V SDRAM Dual Inline Memory Module (DIMM) sockets
• Dual channel 400/333/266 MHz DDR SDRAM interface
• Designed to support up to 4 GB of system memory
NOTE: System resources (such as PCI and AGP) require physical memory address locations that
reduce available memory addresses above 3 GB. This may result in less than 4 GB of memory
being available to the operating system and applications. For more information about the latest
list of tested memory, refer to the Intel World Wide Web site at:
Intel® 865G chipset consisting of:
• Intel® 82865G Graphics and Memory Controller Hub (GMCH) with Accelerated Hub
Architecture (AHA) bus
• Intel® 82801EB I/O Controller Hub (ICH5) with support for up to six
Hi-Speed Universal Serial Bus 2.0 (USB 2.0) ports
• 4 Mbit Firmware Hub (FWH)
• Intel 865G chipset
• Integrated Intel® Extreme Graphics 2
• 1.5 V and 0.8 V only AGP connector
• Single AGP port via the connector or integrated graphics
• AGP 3.0 including 1x/4x/8x AGP data transfers and 1x/4x/8x Fast Writes
• Intel 865G chipset (AC ’97)
• Flexible 6-Channel Audio with Jack Sensing
• Analog Devices Inc. codec
continued
9
Intel Desktop Boards D865GBF/D865GLC Product Guide
Table 2.
Feature Summary (continued)
• Up to eight USB 2.0 ports
—
Four ports routed to the back panel
—
Four ports routed to the internal USB header
• Two IDE interfaces with Ultra DMA-33 and ATA-66/100 support
• Two Serial ATA (SATA) connectors
• One diskette drive interface
• One parallel port
• One serial port
• One VGA port
• PS/2* keyboard and mouse ports
• Up to six PCI bus add-in card connectors (SMBus routed to PCI bus 2)
• One AGP connector
• Intel/AMI BIOS
• 4 Mbit symmetrical flash memory
• Support for SMBIOS
• Support for Advanced Configuration and Power Interface (ACPI)
• Suspend to RAM (STR)
• Wake on USB, PCI, RS-232, PS/2, LAN, and front panel
• Hardware monitor with:
• Three fan sensing inputs used to monitor fan activity
• Temperature sensing
• Intel® Precision Cooling Technology fan speed control that automatically
adjusts chassis fan speeds based on system temperature
• Voltage sensing to detect out of range values
Related Links:
For more information about Intel Desktop Board D865GBF/D865GLC, including the Technical
Product Specification (TPS), BIOS updates, and device drivers, go to:
10
Desktop Board Features
Manufacturing Options
Table 3 below describes the manufacturing options for Desktop Board D865GBF/D865GLC.
Table 3.
Option
Manufacturing Options
Description
Intel® 82562EX 10/100 Mbit/sec Platform LAN Connect (PLC) device and
LAN
RJ-45 connector
Intel® 82540EI 10/100/1000 Mbit/sec Gigabit Ethernet controller and
RJ-45 connector
Gigabit LAN
Supported Operating Systems
The desktop board supports the following operating systems:
•
•
•
•
Microsoft Windows* 98 SE
Microsoft Windows Me
Microsoft Windows 2000
Microsoft Windows XP
11
Intel Desktop Boards D865GBF/D865GLC Product Guide
Desktop Board Components
Figure 1 shows the approximate location of the major components on Desktop Board D865GBF.
Line
In
USB 2.0
Devices
USB 2.0
Devices
C
D
E
A
B
F
AA
G
Z
Y
H
I
X
J
W
V
K
L
T
P
R
O
M
N
S
Q
U
OM15224
Figure 1. Desktop Board D865GBF Components
NOTE
Desktop board D865GLC has three PCI bus add-in card connectors.
12
Desktop Board Features
Table 4.
Desktop Board Components
Label
A
Description
CD-ROM connector (ATAPI-style)
Front panel audio header
Auxiliary line-in connector (ATAPI-style)
AGP connector
B
C
D
E
Rear chassis fan header (fan speed control)
12 V processor core voltage connector
Processor socket
F
G
H
I
Intel 82865G (GMCH)
Processor fan header
J
Channel A DIMM socket
Channel B DIMM socket
Main power connector
K
L
M
N
O
P
Diskette drive connector
Primary IDE connector
Secondary IDE connector
Front chassis fan connector (fan speed control)
Chassis intrusion header
Serial ATA connectors
Speaker
Q
R
S
T
BIOS configuration jumper
Alternate power/sleep LED header
Front panel header
U
V
W
X
USB 2.0 header
Intel 82801EB (ICH5)
Y
USB 2.0 header
Z
Battery
AA
PCI bus add-in card connectors
Related Links:
Go to the following links for the latest information about:
•
•
•
•
Intel Desktop Board D865GBF/D865GLC, http://www.intel.com/design/motherbd
audio software and utilities, http://www.intel.com/design/motherbd
LAN software and drivers, http://www.intel.com/design/motherbd
13
Intel Desktop Boards D865GBF/D865GLC Product Guide
Processor
CAUTION
Failure to use an ATX12V power supply, or not connecting the 12 V processor core voltage power
supply connector to Desktop Board D865GBF/D865GLC may result in damage to the desktop
board and/or power supply.
Desktop Board D865GBF/D865GLC supports a single Intel Pentium 4 processor or Intel Celeron
processor. Processors are not included with the desktop board and must be purchased separately.
The processor connects to the Intel desktop board through the mPGA478-pin socket. The Intel
processors may be removed and replaced to accommodate supported higher speed processors.
Desktop Board D865GBF/D865GLC supports the processors listed in Table 5.
Table 5.
Supported Processors
Designation
FSB Frequency
(MHz)
L2 Cache
(KB)
Type
(GHz)
Intel® Pentium® 4 processor
featuring
Hyper-Threading Technology
3, 2.80C, 2.60C, and 2.40C
800
533
533
512
512
512
3.06
Intel Pentium 4 processor
2.8, 2.66, 2.53, 2.4B, and
2.26
2.6, 2.5, 2.40, 2.20, 2A,
1.80A, and 1.60A
400
400
512
128
Intel® Celeron® processor
2.2, 2.1, and 2.0
Desktop Board D865GBF/D865GLC requires an ATX12V compliant power supply to function
according to desktop board specifications. The board has two ATX12V compliant power supply
connectors that are needed to provide extra power to the Intel 865G chipset and Intel processor.
Related Links:
Go to the following link or sections in this manual for more information about:
•
the latest information on supported Intel processors for Desktop Board D865GBF/D865GLC
•
14
Desktop Board Features
Main Memory
NOTE
To be fully compliant with all applicable Intel® SDRAM memory specifications, the board should
be populated with DIMMs that support the Serial Presence Detect (SPD) data structure. If your
memory modules do not support SPD, you will see a notification to this effect on the screen at
power up. The BIOS will attempt to configure the memory controller for normal operation.
The desktop board supports system memory as defined below:
•
Dual channel and up to four 184-pin Double Data Rate (DDR) SDRAM Dual Inline Memory
Module (DIMMs) connectors with gold-plated contacts.
•
Supported memory configurations are:
Front Side Bus
Frequency
Memory Speed
Outcome
Memory Speed
Processor
DDR400
DDR333
Pentium 4 processor
Pentium 4 processor
Pentium 4 processor
800 MHz
800 MHz
533 MHz
400 MHz
400 MHz
320 MHz
333 MHz
266 MHz
Pentium 4 processor or
Celeron processor
DDR266
Pentium 4 processor
Celeron processor
533 MHz or 400 MHz
400 MHz
266 MHz
266 MHz
•
Support for:
Unbuffered, non-registered DIMMs
Serial Presence Detect (SPD) memory only
Support for Suspend to RAM (STR), S3 ACPI state
Non-ECC DDR (ECC memory will run in non-ECC mode)
2.5 V memory
NOTE
System resources (such as PCI and AGP) require physical memory address locations that reduce
available memory addresses above 3 GB. This may result in less than 4 GB of memory being
available to the operating system and applications.
Related Links:
Go to the following links or section in this manual for more information about:
•
•
•
the latest list of tested memory, http://support.intel.com/support/motherboards/desktop/
15
Intel Desktop Boards D865GBF/D865GLC Product Guide
Intel® 865G Chipset
The Intel 865G chipset consists of the following devices:
•
•
•
Intel 82865G Graphics and Memory Controller Hub (GMCH) with AHA bus
Intel 82801EB I/O Controller Hub (ICH5) with AHA bus
Firmware Hub (FWH)
Related Link:
For more information about Intel 865G chipset, go to:
Graphics Subsystem
The graphics subsystem features the following:
•
•
•
Intel 865G chipset
Intel Extreme Graphics 2
AGP 8x
Audio Subsystem
The audio subsystem features the following:
•
•
•
Intel 865G chipset (AC ’97)
Flexible 6-Channel Audio with Jack Sensing
Analog Devices Inc. AD1985 audio codec
Flexible 6-Channel Audio with Jack Sensing
The Flex 6 audio subsystem includes the following:
•
•
•
Intel 82801EB I/O Controller Hub (ICH5)
Analog Devices AD1985 audio codec
Microphone input that supports a single dynamic, condenser, or electret microphone
The subsystem has the following connectors:
•
•
ATAPI-style CD-ROM connector
Front panel audio connector, including pins for:
Line out
Mic in
•
Back panel audio connectors that are configurable through the audio devices drivers.
Line in or Rear left/right out
Line out or Front left/right out
Mic in or Center LFE out
16
Desktop Board Features
Related Links:
Go to the following link or sections in this manual for more information about:
•
•
•
audio drivers and utilities, http://support.intel.com/support/motherboards/desktop/
Input/Output (I/O) Controller
The super I/O controller features the following:
•
•
•
Low pin count (LPC) interface
One serial port
One parallel port with Extended Capabilities Port (ECP) and Enhanced Parallel Port
(EPP) support
•
•
•
•
•
Serial IRQ interface compatible with serialized IRQ support for PCI systems
PS/2-style mouse and keyboard interfaces
Interface for one 1.2 MB, 1.44 MB, or 2.88 MB diskette drive
Intelligent power management, including a programmable wake up event interface
PCI power management support
LAN Subsystem (Optional)
The optional LAN provides a Fast PCI LAN subsystem. The LAN subsystem provides the
following functions:
•
Basic 10/100 Ethernet LAN (Intel 82562EX) or 10/100/1000 Gigabit Ethernet LAN
(Intel 82540EI)
•
•
•
Support for RJ-45 connector with status indicator LEDs
Programmable transit threshold
Configurable EEPROM that contains the MAC address
LAN Subsystem Software
For LAN software and drivers, refer to the D865GLC or D865GBF link on Intel’s World Wide
Web site at:
17
Intel Desktop Boards D865GBF/D865GLC Product Guide
RJ-45 LAN Connector LEDs
board is powered up and the 10/100 Ethernet LAN subsystem is operating.
Table 6.
RJ-45 10/100 Ethernet LAN Connector LEDs
LED Color
LED State
Indicates
Green
Off
10 Mbit/sec data rate is selected.
100 Mbit/sec data rate is selected.
LAN link is not established.
LAN link is established.
On
Yellow
Off
On (steady state)
On (brighter and pulsing) The computer is communicating with another computer on the
LAN.
Table 7 describes the LED states when the board is powered up and the 10/100/1000 Gigabit
Ethernet LAN subsystem is operating.
Table 7.
RJ-45 10/100/1000 Gigabit Ethernet LAN Connector LEDs
LED Color
LED State
Off
Indicates
Bi-color LED
10 Mbit/sec data rate is selected.
100 Mbit/sec data rate is selected.
1 Gbit/sec data rate is selected.
LAN link is not established.
LAN link is established.
Green
Yellow
Green
Off
On (steady state)
On (brighter and
pulsing)
The computer is communicating with another computer on the
LAN.
Hi-Speed USB 2.0 Support
NOTE
Computer systems that have an unshielded cable attached to a USB port might not meet FCC
Class B requirements, even if no device or a low-speed USB device is attached to the cable.
Use a shielded cable that meets the requirements for a full-speed USB device.
The desktop board supports up to eight USB 2.0 ports via ICH5; four ports routed to the back
panel and four routed to the internal USB 2.0 headers. USB 2.0 ports are backward compatible
with USB 1.1 devices. USB 1.1 devices will function normally at USB 1.1 speeds.
USB 2.0 support requires both an operating system and drivers that fully support USB 2.0 transfer
rates. Disabling Hi-Speed USB in the BIOS reverts all USB 2.0 ports to USB 1.1 operation. This
may be required to accommodate operating systems that do not support USB 2.0.
NOTE
USB devices are limited to USB 1.1 transfer rates prior to operating system and driver
initialization.
18
Desktop Board Features
Enhanced IDE Interface
The ICH5’s IDE interface handles the exchange of information between the processor and
peripheral devices like hard disks, CD-ROM drives, and Iomega Zip* drives inside the computer.
The interface supports:
•
•
•
•
•
Up to four IDE devices (such as hard drives)
ATAPI-style devices (such as CD-ROM drives)
Older PIO Mode devices
Ultra DMA-33 and ATA-66/100 protocols
Laser Servo (LS-120) drives
Accelerated Graphics Port (AGP)
NOTE
Desktop Board D865GBF/D865GLC is only compatible with 0.8 V and 1.5 V AGP cards.
The AGP connector is keyed for 0.8 V and 1.5 V AGP cards only; the connector is not mechanically
compatible with legacy 3.3 V AGP cards. Do not attempt to install a legacy 3.3 V AGP card.
AGP is a high-performance interface for graphics-intensive applications, such as 3D graphics.
AGP is independent of the PCI bus and is intended for exclusive use with graphical display devices.
The AGP 3.0 connector supports 8x, 4x, and 1x AGP cards.
Related Links:
BIOS
The BIOS provides the Power-On Self-Test (POST), the BIOS Setup program, the PCI and IDE
auto-configuration utilities, and the video BIOS. The BIOS is stored in the Firmware Hub.
The BIOS can be updated by following the instructions in Chapter 3 on page 49.
PCI Auto Configuration
If you install a PCI add-in card in your computer, the PCI auto-configuration utility in the BIOS
automatically detects and configures the resources (IRQs, DMA channels, and I/O space) for that
add-in card. You do not need to run the BIOS Setup program after you install a PCI add-in card.
IDE Auto Configuration
If you install an IDE device (such as a hard drive) in your computer, the IDE auto-configuration
utility in the BIOS automatically detects and configures the device for your computer. You do not
need to run the BIOS Setup program after installing an IDE device. You can override the auto-
configuration options by specifying manual configuration in the BIOS Setup program.
To use ATA-66/100 features, the following items are required:
•
•
•
An ATA-66/100 peripheral device
An ATA-66/100 compatible cable
ATA-66/100 operating system device drivers
19
Intel Desktop Boards D865GBF/D865GLC Product Guide
Security Passwords
The BIOS includes security features that restrict whether the BIOS Setup program can be accessed
and who can boot the computer. A supervisor password and a user password can be set for the
Setup and for booting the computer, with the following restrictions:
•
•
•
The supervisor password gives unrestricted access to view and change all Setup options. If
only the supervisor password is set, pressing <Enter> at the password prompt of Setup gives the
user restricted access to Setup.
If both the supervisor and user passwords are set, you must enter either the supervisor password
or the user password to access Setup. Setup options are then available for viewing and
changing depending on whether the supervisor or user password was entered.
Setting a user password restricts who can boot the computer. The password prompt is
displayed before the computer is booted. If only the supervisor password is set, the computer
boots without asking for a password. If both passwords are set, you can enter either password
to boot the computer.
Chassis Intrusion
The board supports a chassis security feature that detects if the chassis cover has been removed.
The security feature uses a mechanical switch on the chassis that can be connected to the chassis
intrusion header.
Power Management Features
Power management is implemented at several levels, including:
•
•
Advanced Configuration and Power Interface (ACPI)
Hardware support:
Power connectors
Fan connectors
Fan Speed Control
Suspend to RAM (Instantly Available PC technology)
Resume on Ring
Wake from USB
Wake from PS/2 keyboard/mouse
PME# wakeup support
ACPI
ACPI gives the operating system direct control over the power management and Plug & Play
functions of a computer. The use of ACPI with the desktop board requires an operating system that
provides full ACPI support.
Power Connectors
power connectors.
20
Desktop Board Features
Fan Connectors
The desktop board has two chassis fan connectors (Intel Precision Cooling Technology) and one
®
Fan Speed Control (Intel Precision Cooling Technology)
Intel Precision Cooling Technology automatically adjusts the chassis fan speeds depending on the
system’s temperature. This feature reduces system fan noise by lowering the speed of the chassis
fans connected to the front and rear chassis fan connectors. The processor fan connector is not
controlled.
The fan speed control feature can be disabled in the BIOS, resulting in the chassis fans always
operating at full speed. This feature should be disabled if a self-controlled fan is attached to a
chassis fan connector.
Overall system noise reduction will vary based on system configuration and environment.
Suspend to RAM (Instantly Available PC Technology)
CAUTION
For Instantly Available PC technology, the 5 V standby line for the power supply must be capable
of delivering adequate +5 V standby current. Failure to provide adequate standby current when
using this feature can damage the power supply and/or effect ACPI S3 sleep state functionality.
Instantly Available PC technology enables the board to enter the ACPI S3 (Suspend-to-RAM) sleep
state. While in the S3 sleep state, the computer will appear to be off. When signaled by a wake-up
device or event, the system quickly returns to its last known awake state.
to the system. This includes the memory modules and PCI bus connectors, even when the
computer appears to be off.
If the system has a dual-colored power LED on the front panel, the sleep state is indicated by the
LED turning amber.
21
Intel Desktop Boards D865GBF/D865GLC Product Guide
CR7J1
OM15225
Figure 2. Location of Standby Power Indicator
CAUTION
Power supplies used with this desktop board must be able to provide enough standby current to
support the standard Instantly Available (ACPI S3 sleep state) configuration. If the standby
current necessary to support multiple wake events from the PCI and/or USB buses exceeds power
supply capacity, the desktop board may lose register settings stored in memory.
Related Link:
For more information about standby current requirements for these desktop boards, refer to the TPS
by selecting the Technical Documentation link at:
Resume on Ring
The operation of Resume on Ring can be summarized as follows:
•
•
•
•
Resumes operation from either ACPI S1 or ACPI S3 state
Requires only one call to access the computer
Detects incoming call similarly for external and internal modems
Requires modem interrupt be unmasked for correct operation
Wake from USB
USB bus activity wakes the computer from an ACPI S1 or S3 state.
NOTE
Wake from USB requires the use of a USB peripheral that supports Wake from USB.
22
Desktop Board Features
Wake from PS/2 Keyboard/Mouse
PS/2 keyboard/mouse activity wakes the computer from an ACPI S1 or S3 state.
PME# Wakeup Support
When the PME# signal on the PCI bus is asserted, the computer wakes from an ACPI S1, S3,
or S5 state.
Speaker
A speaker is mounted on the desktop board. The speaker provides audible error code (beep code)
information during the Power-On Self-Test (POST).
Battery
The battery on the desktop board keeps the values in CMOS RAM and the clock current when the
Real-Time Clock
The desktop board has a time-of-day clock and 100-year calendar. The battery on the desktop
board keeps the clock current when the computer is turned off.
23
Intel Desktop Boards D865GBF/D865GLC Product Guide
24
2 Installing and Replacing Desktop
Board Components
This chapter tells you how to:
•
•
•
•
•
•
•
•
•
•
•
Install the I/O shield
Install and remove the desktop board
Install and remove a processor and memory
Install and remove an AGP card
Connect the IDE and Serial ATA cables
Connect internal headers
Connecting 6-Channel Flex Audio with Jack Sensing
Connect hardware control and power cables
Set the BIOS configuration jumper
Clear passwords
Replace the battery
Before You Begin
WARNINGS
The procedures in this chapter assume familiarity with the general terminology associated with
personal computers and with the safety practices and regulatory compliance required for using
and modifying electronic equipment.
Disconnect the computer from its power source and from any telecommunications links,
networks, or modems before performing any of the procedures described in this chapter. Failure
to disconnect power, telecommunications links, networks, or modems before you open the
computer or perform any procedures can result in personal injury or equipment damage. Some
circuitry on the board can continue to operate even though the front panel power button is off.
Follow these guidelines before you begin:
•
•
Always follow the steps in each procedure in the correct order.
Set up a log to record information about your computer, such as model, serial numbers,
installed options, and configuration information.
•
Electrostatic discharge (ESD) can damage components. Perform the procedures described in
this chapter only at an ESD workstation using an antistatic wrist strap and a conductive foam
pad. If such a station is not available, you can provide some ESD protection by wearing an
antistatic wrist strap and attaching it to a metal part of the computer chassis.
25
Intel Desktop Boards D865GBF/D865GLC Product Guide
Installation Precautions
When you install and test the Intel desktop board, observe all warnings and cautions in the
installation instructions.
To avoid injury, be careful of:
•
•
•
•
•
Sharp pins on connectors
Sharp pins on printed circuit assemblies
Rough edges and sharp corners on the chassis
Hot components (like processors, voltage regulators, and heat sinks)
Damage to wires that could cause a short circuit
Observe all warnings and cautions that instruct you to refer computer servicing to qualified
technical personnel.
Installation Instructions
CAUTION
Follow these guidelines to meet safety and regulatory requirements when installing this board
assembly.
Read and adhere to all of these instructions and the instructions supplied with the chassis and
associated modules. If the instructions for the chassis are inconsistent with these instructions or the
instructions for associated modules, contact the supplier’s technical support to find out how you can
ensure that your computer meets safety and regulatory requirements. If you do not follow these
instructions and the instructions provided by chassis and module suppliers, you increase safety risk
and the possibility of noncompliance with regional laws and regulations.
Ensure Electromagnetic Compatibility (EMC) Compliance
Before computer integration, make sure that the power supply and other modules or peripherals, as
applicable, have passed Class B EMC testing and are marked accordingly.
In the installation instructions for the host chassis, power supply, and other modules pay close
attention to the following:
•
•
•
•
Product certifications or lack of certifications
External I/O cable shielding and filtering
Mounting, grounding, and bonding requirements
Keying connectors when mating the wrong connectors could be hazardous
If the power supply and other modules or peripherals, as applicable, are not Class B EMC
compliant before integration, then EMC testing is required on a representative sample of the newly
completed computer.
26
Installing and Replacing Desktop Board Components
Chassis and Component Certifications
Ensure that the chassis and certain components; such as the power supply, peripheral drives,
wiring, and cables; are components certified for the country or market where used. Agency
certification marks on the product are proof of certification. Typical product certifications include:
•
In Europe
The CE marking signifies compliance with all applicable European requirements. If the chassis
and other components are not properly CE marked, a supplier’s Declaration of Conformity
statement to the European EMC directive and Low Voltage directive (as applicable), should be
obtained. Additionally, other directives, such as the Radio and Telecommunications Terminal
Equipment (R&TTE) directive may also apply depending on product features.
•
•
In the United States
A certification mark by a Nationally Recognized Testing Laboratory (NRTL) such as UL, CSA,
or ETL signifies compliance with safety requirements. Wiring and cables must also be UL
listed or recognized and suitable for the intended use. The FCC Class B logo for home or
office use signifies compliance with electromagnetic interference (EMI) requirements.
In Canada
A nationally recognized certification mark such as CSA or cUL signifies compliance with
safety requirements. The Industry Canada statement at the front of this product guide
demonstrates compliance with Canadian EMC regulations. Industry Canada recognizes and
accepts FCC certification as denoting compliance with national electromagnetic interference
(emissions) requirements.
Prevent Power Supply Overload
Do not overload the power supply output. To avoid overloading the power supply, make sure that
the calculated total current loads of all the modules within the computer is less than the output
current rating of each of the power supplies output circuits.
Place Battery Marking
There is insufficient space on this desktop board to provide instructions for replacing and disposing
of the Lithium ion coin cell battery. For system safety certification, the following statement or
equivalent statement is required to be permanently and legibly marked on the chassis near the
battery.
CAUTION
Risk of explosion if the battery is replaced with an incorrect type. Batteries should be recycled
where possible. Disposal of used batteries must be in accordance with local environmental
regulations.
Use Only for Intended Applications
All Intel desktop boards are evaluated as Information Technology Equipment (I.T.E.) for use in
personal computers for installation in homes, offices, schools, computer rooms, and similar
locations. The suitability of this product for other applications or environments, such as medical,
industrial, alarm systems, test equipment, etc. may require further evaluation.
Related Links:
For information about regulatory compliance, go to Appendix B on page 91.
27
Intel Desktop Boards D865GBF/D865GLC Product Guide
Installing the I/O Shield
The desktop board comes with an I/O shield. When installed in the chassis, the shield blocks radio
frequency transmissions, protects internal components from dust and foreign objects, and promotes
correct airflow within the chassis.
Install the I/O shield before installing the desktop board in the chassis. Place the shield inside the
chassis as shown in Figure 3. Press the shield into place so that it fits tightly and securely. If the
shield doesn’t fit, obtain a properly-sized shield from the chassis supplier.
OM15226
Figure 3. Installing the I/O Shield
28
Installing and Replacing Desktop Board Components
Installing and Removing the Desktop Board
WARNING
Only qualified technical personnel should do this procedure. Disconnect the computer from its
power source before performing the procedures described here. Failure to disconnect the power
before you open the computer can result in personal injury or equipment damage.
NOTE
Refer to Appendix B for regulatory requirements.
Refer to your chassis manual for instructions on installing and removing the desktop board.
Board D865GLC has eight mounting holes.
OM15227
Figure 4. Location of Desktop Board Mounting Screw Holes
29
Intel Desktop Boards D865GBF/D865GLC Product Guide
Installing and Removing a Processor
Instructions on how to install the processor to the desktop board are given below.
Installing a Processor
CAUTION
Before installing or removing the processor, make sure that AC power has been removed by
unplugging the power cord from the computer; the standby power LED should not be lit (see
To install a processor, follow these instructions:
2. Locate the processor socket and raise the socket lever completely.
3. Install the processor so that the corner with the triangle marking (A) is aligned with the corner
4. Lower the lever to its original position.
A
OM15028
Figure 5. Installing a Processor
Installing the Processor Fan Heat Sink
Desktop Board D865GBF/D865GLC has an integrated processor fan heat sink retention mechanism
(RM). For instructions on how to install the processor fan heat sink to the integrated processor fan
heat sink RM, refer to the boxed processor manual or the Intel World Wide Web site at:
30
Installing and Replacing Desktop Board Components
Connecting the Processor Fan Heat Sink Cable
OM15229
Figure 6. Connecting the Processor Fan Heat Sink Cable to the Processor Fan Connector
Removing the Processor
For instruction on how to remove the processor fan heat sink and processor, refer to the processor
installation manual or the Intel World Wide Web site at:
31
Intel Desktop Boards D865GBF/D865GLC Product Guide
Installing and Removing Memory
CAUTION
To be fully compliant with all applicable Intel SDRAM memory specifications, the boards require
DIMMs that support the Serial Presence Detect (SPD) data structure. You can access the PC
Serial Presence Detect Specification at:
Desktop Board D865GBF/D865GLC has four dual channel 184-pin DIMM sockets arranged as
the DIMM sockets to show how to match DIMMs for dual channel configuration).
Channel A
DIMM 0
DIMM 1
Channel B
DIMM 0
DIMM 1
OM15230
Figure 7. Installing a Memory Module
32
Installing and Replacing Desktop Board Components
Installing DIMMs
Before installing DIMMs, read and follow these guidelines for dual channel configuration.
NOTE
Performance Acceleration Technology (PAT) requires a processor with 800 MHz FSB frequency
and DDR400 memory.
Install a matched pair of DIMMs equal in speed, size, and technology (see Figure 8) in
DIMM 0 in both channels A and B.
Channel A
DIMM 0
DIMM 1
256 MB, 128 Mb, DDR400
Channel B
DIMM 0
DIMM 1
256 MB, 128 Mb, DDR400
Figure 8. Dual Configuration Example with Two DIMMs
If additional memory is to be used, then install another matched pair of DIMMs in DIMM 1 in
Channel A
DIMM 0
DIMM 1
256 MB, 128 Mb, DDR400
512 MB, 256 Mb, DDR400
Channel B
DIMM 0
DIMM 1
256 MB, 128 Mb, DDR400
512 MB, 256 Mb, DDR400
Figure 9. Dual Configuration Example with Four DIMMs
NOTE
All other memory configurations will result in single channel memory operation.
33
Intel Desktop Boards D865GBF/D865GLC Product Guide
CAUTION
Install memory in the DIMM sockets prior to installing an AGP video card to avoid interference
with the memory retention mechanism.
To install DIMMs, follow these steps:
2. Turn off all peripheral devices connected to the computer. Turn off the computer and
disconnect the AC power cord.
4. Remove the AGP video card if it interferes with the DIMM clips from being easily opened and
closed.
5. Make sure the clips at either end of the DIMM socket(s) are pushed outward to the
open position.
6. Holding the DIMM by the edges, remove it from its anti-static package.
7. Position the DIMM above the socket. Align the small notch in the bottom edge of the DIMM
with the key in the socket (see inset in Figure 7).
8. Insert the bottom edge of the DIMM into the socket.
9. When the DIMM is inserted, push down on the top edge of the DIMM until the retaining clips
snap into place. Make sure the clips are firmly in place.
10. Reinstall the AGP card if it was removed prior to installing the DIMMs.
11. Replace the computer’s cover and reconnect the AC power cord.
Removing DIMMs
To remove a memory module, follow these steps:
2. Turn off all peripheral devices connected to the computer. Turn off the computer.
3. Remove the AC power cord from the computer.
4. Remove the computer’s cover.
5. Remove the AGP card if it interferes with the DIMM clips from being easily opened
and closed.
6. Gently spread the retaining clips at each end of the DIMM socket. The DIMM pops out of
the socket.
7. Hold the DIMM by the edges, lift it away from the socket, and store it in an anti-static package.
8. Reinstall the AGP card if you removed it before taking out the DIMMs.
9. Reinstall and reconnect any parts you removed or disconnected to reach the DIMM sockets.
10. Replace the computer’s cover and reconnect the AC power cord.
34
Installing and Replacing Desktop Board Components
Installing and Removing an AGP Card
CAUTION
When installing any AGP card in the desktop board, ensure that it is fully seated in the AGP
connector before you power on the system. If the card is not fully seated in the AGP connector, an
electrical short may result across the AGP connector pins. Depending on the over-current
protection of the power supply, certain board components and/or traces may be damaged.
The AGP connector supports 0.8 V (4x and 1x) and 1.5 V (8x) AGP cards. The desktop board has
an integrated AGP card retention mechanism (RM).
Installing an AGP Card
Follow these instructions to install an AGP card:
2. Place the card in the AGP connector.
3. Press down on the card until it is completely seated in the AGP connector and the card retention
notch snaps into place around the RM pin.
4. Secure the card’s metal bracket to the chassis back panel with a screw.
Removing the AGP Card
Follow these instructions to remove the AGP card from the RM (see Figure 10):
2. Remove the screw (B) that secures the card’s metal bracket (A) to the chassis back panel.
the notch in the card.
4. Pull the card straight up (D).
B
D
A
C
OM15031
Figure 10. Removing the AGP Card
35
Intel Desktop Boards D865GBF/D865GLC Product Guide
Connecting the IDE Cable
The two IDE cables support the Ultra DMA-33 and ATA-66/100 transfer protocols. Each of the
cable.
NOTE
ATA-66/100 compatible cables are backward compatible with drives using slower IDE transfer
protocols. If an ATA-66/100 disk drive and a disk drive using any other IDE transfer protocol are
attached to the same cable, the maximum transfer rate between the drives may be reduced to that of
the slowest drive.
NOTE
Do not connect an ATA device as a slave on the same IDE cable as an ATAPI master device. For
example, do not connect an ATA hard drive as a slave to an ATAPI CD-ROM drive.
For correct function of the cable:
•
•
•
Attach the cable end with the single connector to the Intel desktop board (A).
Attach the cable end with the two closely spaced connectors to the drives (B).
A
B
OM15232
Figure 11. Connecting the IDE Cable
36
Installing and Replacing Desktop Board Components
Connecting the Serial ATA Cable
The SATA cable (4-conductor) supports the Serial ATA protocol and connects a single drive to the
desktop board. Either end of the cable can be connected to the SATA drive or the connector on the
board (see Figure 12).
For correct cable function:
1. Observe the precaution in “Before You Begin” on page 23.
2. Attach either cable end to the connector (A) on the board.
3. Attach either cable end to the connector (B) on the drive.
A
B
OM15467
Figure 12. Connecting the Serial ATA Cable
37
Intel Desktop Boards D865GBF/D865GLC Product Guide
Connecting Internal Headers
Figure 13 shows the location of internal headers.
1
3
5
7
9
2
4
6
A
10
J9A2
1
2
4
6
8
3
5
7
B
10
1
3
5
7
2
J9F1
4
6
8
C
10
J9H1
1
3
2
4
6
8
5
7
9
D
J9J1
E
1
2
OM15240
Item
Description
A
B
Front panel audio
USB 2.0
C
D
E
USB 2.0
Front panel
Power LED
Figure 13. Internal Headers
38
Installing and Replacing Desktop Board Components
Installing a Front Panel Audio Solution
for the front panel audio header.
Table 8.
Front Panel Audio Header Signal Names (J9A2)
Pin
1
Signal Name
AUD-MIC
Pin
2
Signal Name
AUD-GND
AUD-VCC
AUD-RET-R
KEY
3
AUD-MIC-BIAS
AUD-FPOUT-R
HP-ON
4
5
6
7
8
9
AUD-FPOUT-L
10
AUD-RET-L
To install the cable that connects the front panel audio solution to the front panel audio header,
follow these steps:
2. Turn off all peripheral devices connected to the computer. Turn off the computer and
disconnect the AC power cord.
3. Remove the cover.
4. Locate the front panel audio header. Remove the two jumpers from the header to disable the
back panel audio connectors.
5. Install a correctly keyed and shielded front panel audio cable.
6. Connect the audio cable to the front panel audio solution.
7. Replace the cover.
To restore back panel operations, follow these steps:
2. Turn off all peripheral devices connected to the computer. Turn off the computer and
disconnect the AC power cord.
3. Remove the cover.
4. Remove the front panel audio cable.
5. Install a jumper on pins 5-6 (rear R channel).
6. Install a jumper on pins 9-10 (rear L channel).
7. Replace the cover.
39
Intel Desktop Boards D865GBF/D865GLC Product Guide
Setting up the Flexible 6-Channel Audio with Jack Sensing
After installing the SoundMAX 4 XL audio driver from the Intel Express Installer CD-ROM, the
A
B
C
OM15694
Item
A
Description
Rear left/right out or Line In
Front left/right out or S/PDIF line out
Center-LFE (Subwoofer) or Mic In
B
C
Figure 14. Back Panel Audio Connectors for 6-Channel Audio with Jack Sensing
Multi-Channel Analog Audio
Connect two speakers to the front left/right out (B) and two speakers to the r left/right out (A) for
both 4- and 6-channel audio configurations. For 6-channel audio, connect two additional speakers
to the center-LFE (C).
Multi-Channel Digital Audio
To take advantage of the S/PDIF functionality, a 1/8-inch stereo phone plug to the RCA jack
adapter/splitter is required to convert from the stereo input to RCA connection. Connect the stereo
input side of the adapter to the S/PDIF (B) connector, and connect the speaker system or S/PDIF
decoder to the RCA jack left channel (white, if colored).
Related Link:
40
Installing and Replacing Desktop Board Components
Connecting USB 2.0 Headers
assignments for the headers.
Table 9.
USB 2.0 Headers (J9F1 and J9H1)
USB Port A
Signal Name
Power
USB Port B
Signal Name
Pin
1
Pin
2
Power
D-
3
D-
4
5
D+
6
D+
7
Ground
Key (no pin)
8
Ground
Not connected
9
10
Note: USB ports may be assigned as needed.
Connecting the Front Panel Header
Before connecting the front panel header, observe the precautions in “Before You Begin” on
pin assignments for the front panel header.
Table 10. Front Panel Header (J9J1)
Pin Signal
In/Out Description
Pin Signal
In/Out Description
Power LED
HDR_BLNK_GRN Out Front panel green
Hard Drive Activity LED
1
3
HD_PWR
Out
Hard disk LED pull-
2
4
up (330 Ω) to +5 V
LED
HDA#
Out
Hard disk active LED
HDR_BLNK_YEL Out
Front panel yellow
LED
Reset Switch
On/Off Switch
SWITCH_ON# In
Ground
5
7
9
Ground
Ground
6
8
Power switch
Ground
FP_RESET# In
+5 V Out
Reset switch
Power
10 N/C
Not connected
41
Intel Desktop Boards D865GBF/D865GLC Product Guide
Connecting Hardware Control and Power Cables
Figure 15 shows the location of the chassis intrusion and fan headers, and power connectors.
Chassis
rear fan
1
J6B1
12 V
processor core
voltage connector
2
1
Processor
fan
1
J6B1
Chassis intrusion
connector
Main power
connector
Chassis
front fan
1
2
1
1
J9H2
J7J3
OM15237
Figure 15. Location of Hardware Control Headers and Power Connectors
42
Installing and Replacing Desktop Board Components
Connecting the Chassis Intrusion Cable
Connect the chassis intrusion cable to the header shown in Figure 15.
Connecting Fans
Connect the processor’s fan heat sink cable to the processor fan header on the board. Connect
Connecting Power Cables
CAUTION
Failure to use an ATX12V power supply, or not connecting the 12 V processor core voltage power
supply connector to the desktop board may result in damage to the desktop board and/or power
supply.
Figure 15 shows the location of power connectors.
2. Connect the 12 V processor core voltage power supply cable to the 2x2 connector.
3. Connect the main power cable to the 2x10 connector.
43
Intel Desktop Boards D865GBF/D865GLC Product Guide
Setting the BIOS Configuration Jumper Block
CAUTION
Always turn off the power and unplug the power cord from the computer before changing the
jumper. Moving the jumper with the power on may result in unreliable computer operation.
1
3
J9J4
OM15233
Figure 16. Location of the BIOS Configuration Jumper Block
The three-pin BIOS jumper block enables all board configurations to be done in BIOS Setup.
Table 11 shows the jumper settings for the Setup program modes.
Table 11. Jumper Settings for the BIOS Setup Program Modes (J9J4)
Jumper Setting
Mode
Description
Normal (default) (1-2) The BIOS uses the current configuration and passwords for
booting.
1
1
1
3
3
3
Configure (2-3)
After the Power-On Self-Test (POST) runs, the BIOS displays
the Maintenance Menu. Use this menu to clear passwords.
Recovery (None)
The BIOS recovers data from a recovery diskette in the event of
a failed BIOS update.
44
Installing and Replacing Desktop Board Components
Clearing Passwords
This procedure assumes that the board is installed in the computer and the configuration jumper
block is set to normal mode.
2. Turn off all peripheral devices connected to the computer. Turn off the computer. Disconnect
the computer’s power cord from the AC power source (wall outlet or power adapter).
3. Remove the computer cover.
5. Place the jumper on pins 2-3 as shown below.
3
1
6. Replace the cover, plug in the computer, turn on the computer, and allow it to boot.
7. The computer starts the Setup program. Setup displays the Maintenance menu.
8. Use the arrow keys to select Clear Passwords. Press <Enter> and Setup displays a pop-up
screen requesting that you confirm clearing the password. Select Yes and press <Enter>.
Setup displays the maintenance menu again.
9. Press <F10> to save the current values and exit Setup.
10. Turn off the computer. Disconnect the computer’s power cord from the AC power source.
11. Remove the computer cover.
12. To restore normal operation, place the jumper on pins 1-2 as shown below.
1
3
13. Replace the cover, plug in the computer, and turn on the computer.
45
Intel Desktop Boards D865GBF/D865GLC Product Guide
Replacing the Battery
A coin-cell battery (CR2032) powers the real-time clock and CMOS memory. When the computer
is not plugged into a wall socket, the battery has an estimated life of three years. When the
computer is plugged in, the standby current from the power supply extends the life of the battery.
The clock is accurate to 13 minutes/year at 25 ºC with 3.3 VSB applied.
When the voltage drops below a certain level, the BIOS Setup program settings stored in CMOS
RAM (for example, the date and time) might not be accurate. Replace the battery with an
CAUTION
Risk of explosion if the battery is replaced with an incorrect type. Batteries should be recycled
where possible. Disposal of used batteries must be in accordance with local environmental
regulations.
PRECAUTION
Risque d'explosion si la pile usagée est remplacée par une pile de type incorrect. Les piles usagées
doivent être recyclées dans la mesure du possible. La mise au rebut des piles usagées doit
respecter les réglementations locales en vigueur en matière de protection de l'environnement.
FORHOLDSREGEL
Eksplosionsfare, hvis batteriet erstattes med et batteri af en forkert type. Batterier bør om muligt
genbruges. Bortskaffelse af brugte batterier bør foregå i overensstemmelse med gældende
miljølovgivning.
OBS!
Det kan oppstå eksplosjonsfare hvis batteriet skiftes ut med feil type. Brukte batterier bør kastes i
henhold til gjeldende miljølovgivning.
VIKTIGT!
Risk för explosion om batteriet ersätts med felaktig batterityp. Batterier ska kasseras enligt de
lokala miljövårdsbestämmelserna.
VARO
Räjähdysvaara, jos pariston tyyppi on väärä. Paristot on kierrätettävä, jos se on mahdollista.
Käytetyt paristot on hävitettävä paikallisten ympäristömääräysten mukaisesti.
VORSICHT
Bei falschem Einsetzen einer neuen Batterie besteht Explosionsgefahr. Die Batterie darf nur durch
denselben oder einen entsprechenden, vom Hersteller empfohlenen Batterietyp ersetzt werden.
Entsorgen Sie verbrauchte Batterien den Anweisungen des Herstellers entsprechend.
46
Installing and Replacing Desktop Board Components
AVVERTIMENTO
Esiste il pericolo di un esplosione se la pila non viene sostituita in modo corretto. Utilizzare solo
pile uguali o di tipo equivalente a quelle consigliate dal produttore. Per disfarsi delle pile usate,
seguire le istruzioni del produttore.
PRECAUCIÓN
Existe peligro de explosión si la pila no se cambia de forma adecuada. Utilice solamente pilas
iguales o del mismo tipo que las recomendadas por el fabricante del equipo. Para deshacerse de
las pilas usadas, siga igualmente las instrucciones del fabricante.
WAARSCHUWING
Er bestaat ontploffingsgevaar als de batterij wordt vervangen door een onjuist type batterij.
Batterijen moeten zoveel mogelijk worden gerecycled. Houd u bij het weggooien van gebruikte
batterijen aan de plaatselijke milieuwetgeving.
ATENÇÃO
Haverá risco de explosão se a bateria for substituída por um tipo de bateria incorreto. As baterias
devem ser recicladas nos locais apropriados. A eliminação de baterias usadas deve ser feita de
acordo com as regulamentações ambientais da região.
47
Intel Desktop Boards D865GBF/D865GLC Product Guide
To replace the battery, follow these steps:
2. Turn off all peripheral devices connected to the computer. Disconnect the computer’s power
cord from the AC power source (wall outlet or power adapter).
3. Remove the computer cover.
5. With a medium flat-bladed screwdriver, gently pry the battery free from its connector. Note the
orientation of the “+” and “-” on the battery.
6. Install the new battery in the connector, orienting the “+” and “-” correctly.
7. Replace the computer cover.
OM15234
Figure 17. Removing the Battery
48
3 Updating the BIOS
This chapter tells you how to update the BIOS by either using the Intel® Express BIOS Update
utility or the Iflash Memory Update utility, and how to recover the BIOS if an update fails.
Updating the BIOS with the Intel® Express BIOS
Update Utility
With the Intel Express BIOS Update utility you can update the system BIOS while in the Windows
environment. The BIOS file is included in an automated update utility that combines the
functionality of the Intel® Flash Memory Update Utility and the ease-of use of Windows-based
installation wizards.
To update the BIOS with the Intel Express BIOS Update utility:
1. Go to the Intel World Wide Web site:
2. Navigate to the Desktop Board D865GBF or D865GCL page and click the Express BIOS
Update utility file for the Desktop Board D865GBF/D865GLC BIOS.
3. Download the file to your hard drive. (You can also save this file to a diskette. This is useful if
you are updating the BIOS for multiple identical systems.)
4. Close all other applications. This step is required. Your system will be rebooted at the last
Express BIOS Update window.
5. Double-click the executable file from the location on your hard drive where it was saved. This
runs the update program.
6. Follow the instructions provided in the dialog boxes to complete the BIOS update.
49
Intel Desktop Boards D865GBF/D865GLC Product Guide
Updating the BIOS with the Iflash Memory Update
Utility
With the Iflash Memory Update utility you can update the system BIOS from a floppy disk or other
bootable media. The utility available from the Web provides a simple method for creating a
bootable flash memory update floppy that will automatically update your BIOS.
Obtaining the BIOS Update File
You can update to a new version of the BIOS by using the BIOS update file. The BIOS update file
is a compressed self-extracting archive that contains all the files you need to update the BIOS. The
BIOS update file contains:
•
•
•
New BIOS files
BIOS recovery files
Iflash Memory Update utility
You can obtain the BIOS update file through your computer supplier or by navigating to the
Desktop Board D865GBF or D865GCL page on the Intel World Wide Web site:
NOTE
Review the instructions distributed with the update utility before attempting a BIOS update.
The Intel Flash Memory Update Utility allows you to:
•
•
Update the BIOS in flash memory
Update the language section of the BIOS
Updating the BIOS
CAUTION
The AUTOEXEC.BAT file provided with the update files updates the BIOS. Do not interrupt the
process or the system may not function.
1. Boot the computer with the BIOS update diskette in drive A. During system boot, the
AUTOEXEC.BAT file provided with the update files will automatically run the BIOS update
process.
2. When the update process is complete, the monitor will display a message telling you to remove
the diskette and to reboot the system.
3. As the computer boots, check the BIOS identifier (version number) to make sure the update
was successful. If a logo appears, press <Esc> to view the POST messages.
50
Updating the BIOS
Recovering the BIOS
It is unlikely that anything will interrupt the BIOS update; however, if an interruption occurs, the
BIOS could be damaged. The following steps explain how to recover the BIOS if an update fails.
information on Setup modes.
NOTE
Because of the small amount of code available in the boot block area, there is no video support.
You will not see anything on the screen during this procedure. Monitor the procedure by listening
to the speaker and looking at the diskette drive LED.
1. Turn off the computer, disconnect the computer’s power cord, and disconnect all external
peripherals.
3. Remove the jumper from all pins as shown below to set recovery mode for Setup.
1
3
4. Insert the bootable BIOS update diskette into diskette drive A.
5. Replace the computer cover, connect the power cord, turn on the computer, and allow it to
boot. The recovery process will take a few minutes.
6. Listen to the speaker:
•
Upon applying power, drive A will begin to show activity. In about a minute, two beeps
are heard and drive A activity ceases (temporarily) indicating the successful recovery of the
BIOS core. Drive A activity will begin again followed by two more beeps indicating the
successful recovery of the boot block. This sequence of events indicates a successful BIOS
recovery.
•
A series of continuous beeps indicates a failed BIOS recovery.
7. If recovery fails, return to step 1 and repeat the recovery process.
8. If recovery is successful, turn off the computer, and disconnect its power cord.
9. Remove the computer cover and continue with the following steps.
10. On the jumper block, reinstall the jumper back on pins 1-2 as shown below to set normal mode
for Setup.
1
3
11. Leave the update diskette in drive A, replace the computer cover, and connect the computer’s
power cord.
12. Turn on the computer and continue with the BIOS update.
51
4 Using the BIOS Setup Program
The BIOS Setup program can be used to view and change the BIOS settings for the computer. The
BIOS Setup program is accessed by pressing the <F2> key after the Power-On Self-Test (POST)
memory test begins and before the operating system boot begins.
NOTE
The BIOS Setup menus described in this section may not show the latest settings. For the latest
BIOS settings, refer to the Intel® Desktop Board D865GBF/D865GLC Technical Product
Specification or the Intel World Wide Web site:
NOTE
For reference purposes, you should write down the current Setup settings. When you make changes
to the settings, update this record.
NOTE
The Setup menus described in this section apply to the desktop boards with BIOS identifier
BF86510A.86A. Boards with other BIOS identifiers might have differences in some of the
Setup menu screens.
Table 12 shows the BIOS Setup program menu bar.
Table 12. BIOS Setup Program Menu Bar
Maintenance
Main
Advanced
Security
Power
Boot
Exit
Clears passwords
and Boot Integrity
Service (BIS)*
credentials, and
configures extended
configuration
Allocates
resources for advanced
hardware features
components available
through the
Configures
Sets passwords Configures
Selects boot
options and
Saves or
discards
and security
features
power
management power supply changes to set
features controls program options
chipset
memory settings
* For information about the BIS, refer to the Intel Web site at:
53
Intel Desktop Boards D865GBF/D865GLC Product Guide
Table 13 shows the function keys available for menu screens.
Table 13. BIOS Setup Program Function Keys
BIOS Setup Program Function Key
Description
<←> or <→>
Selects a different menu screen
Moves cursor up or down
<↑> or <↓>
<Tab>
Moves cursor to the next field
<Enter>
<F9>
Executes command or selects the submenu
Load the default configuration values for the current menu
Save the current values and exits the BIOS Setup program
Exits the menu
<F10>
<Esc>
Maintenance Menu
Maintenance Main
Advanced
Security
Power Boot
Exit
CPU Frequency
[13 To 1 Ratio]
Clear All Passwords
Clear BIS credentials
CPU Stepping Signature
[F29]
CPU Microcode Update Rev.
[<none loaded>]
m o
n p
Enter
F1
P9
F10
ESC
Select Screen
Select Item
Selecto Sub-Menu
General Help
Setup Defaults
Save and Exit
Exit
Table 14. Maintenance Menu
Feature
Options
Description
No options
CPU Frequency
Clear All Passwords
• Ok
Clears both the user and supervisor passwords.
• Cancel
Clear BIS Credentials
• Ok
• Cancel
Clears the Wired for Management Boot Integrity Service
(BIS) credentials.
CPU Stepping Signature
No options Displays processor’s Stepping Signature.
CPU Microcode Update Revision No options Displays processor’s Microcode Update Revision.
* For information about the BIS, refer to the Intel Web site at:
54
Using the BIOS Setup Program
Main Menu
Main Advanced
Security
Power
Boot
Exit
BIOS Version
xxxxx10A.86A.xxxx.xxx
Intel(R) Pentium(R) 4
Processor Type
Hyper-Threading Technology [Enabled]
Processor Speed
System Bus Speed
System Memory Speed
X.XX GHz
XXX MHz
XXX MHz
Cache RAM
XXX KB
Total Memory
Memory Mode
XXX MB
Dual Channel
Memory Channel A Slot 0 XXX MB (DDRYYY)
Memory Channel A Slot 1 Not Installed
Memory Channel B Slot 0 XXX MB (DDRYYY)
Memory Channel B Slot 1 Not Installed
m o
n p
Enter
F1
P9
F10
ESC
Select Screen
Select Item
Select f Sub-Menu
General Help
Setup Defaults
Save and Exit
Exit
Language
System Time
[English]
[xx.xx.xx]
used to configure the system date and system time.
Table 15. Main Menu
Feature
Options
Description
BIOS Version
Processor Type
No options
Displays the version of the BIOS.
Displays processor type.
No options
• Enabled (default)
Hyper-Threading
Technology
Enables or disables Hyper-Threading Technology.
• Disabled
Processor Speed
System Bus Speed
System Memory Speed
Cache RAM
No options
No options
No options
No options
Displays processor speed.
Displays the system bus speed.
Displays the system memory speed.
Displays the size of second-level cache and whether it
is ECC-capable.
Total Memory
Memory Mode
No options
No options
Displays the total amount of RAM.
Displays the amount and type of RAM in the
memory banks.
Language
• English (default)
• Français
Selects the current default language used by the
BIOS.
System Time
Hour, minute, and
second
Specifies the current time.
55
Intel Desktop Boards D865GBF/D865GLC Product Guide
Advanced Menu
Main
Advanced Security Power Boot Exit
Setup Warning:
Setting items on this screen to incorrect values
may cause your system to malfunction!
` PCI Configuration
` Boot Configuration
` Peripheral Configuration
` IDE Configuration
` Diskette Configuration
` Event Log Configuration
` Video Configuration
` USB Configuration
` Chipset Configuration
` Fan Control Configuration
` Hardware Management
m o
n p
Enter
F1
P9
F10
ESC
Select Screen
Select Item
Select ` Sub-Menu
General Help
Setup Defaults
Save and Exit
Exit
available through the chipset.
Table 16. Advanced Menu
Feature
Options
Description
PCI Configuration
No options
Configures individual PCI slot’s IRQ priority. When selected,
displays the PCI Configuration submenu.
Boot Configuration
No options
No options
Configures Plug & Play and the Numlock key, and resets
configuration data. When selected, displays the Boot
Configuration submenu.
Peripheral Configuration
Configures peripheral ports and devices. When selected,
displays the Peripheral Configuration submenu.
IDE Configuration
No options
No options
Specifies type of connected IDE device.
Configures the floppy drive(s). When selected, displays the
Diskette Configuration submenu.
Diskette Configuration
Event Log Configuration
Video Configuration
USB Configuration
No options
No options
No options
No options
Configures event logging. When selected, displays the Event
Log Configuration submenu.
Configures video features. When selected, displays the
Video Configuration submenu.
Configures USB features. When selected, displays the USB
Configuration submenu.
Chipset Configuration
Configures chipset features. When selected, displays the
Chipset Configuration submenu.
Fan Control Configuration No options
Hardware Management No options
Configures fan control features. When selected, displays the
Fan Control Configuration submenu.
Configures hardware management. When selected, displays
the Hardware Management submenu.
56
Using the BIOS Setup Program
PCI Configuration Submenu
Main Advanced Security Power Boot Exit
PCI Configuration
PCI Slot 1 IRQ Priority
PCI Slot 2 IRQ Priority
PCI Slot 3 IRQ Priority
PCI Slot 4 IRQ Priority
PCI Slot 5 IRQ Priority
[Auto]
m o
Select Screen
Select Item
Select ` Sub-Menu
General Help
Setup Defaults
Save and Exit
Exit
n p
Enter
F1
P9
F10
ESC
Table 17. PCI Configuration Submenu
Feature
Options
Description
PCI Slot 1 IRQ Priority
PCI Slot 2 IRQ Priority
PCI Slot 3 IRQ Priority
PCI Slot 4 IRQ Priority
PCI Slot 5 IRQ Priority
• Auto (default)
• 3
• 5
Allows selection of IRQ priority.
• 9
• 10
• 11
57
Intel Desktop Boards D865GBF/D865GLC Product Guide
Boot Configuration Submenu
Main Advanced Security Power Boot Exit
Boot Configuration
Plug & Play O/S
Numlock
[No]
[On]
m o
n p
Enter
F1
P9
F10
ESC
Select Screen
Select Item
Select ` Sub-Menu
General Help
Setup Defaults
Save and Exit
Exit
the Numlock key.
Table 18. Boot Configuration Submenu
Feature
Options
Description
Plug & Play O/S
• No (default)
• Yes
Specifies if manual configuration is desired.
No lets the BIOS configure all devices in the system. This
setting is appropriate when using a Plug and Play operating
system.
Yes lets the operating system configure Plug & Play (PnP)
devices not required for boot if your system has a Plug & Play
operating system. This option is available for use during lab
testing.
Numlock
• Off
Specifies the power-on state of the Numlock feature on the
numeric keypad of the keyboard.
• On (default)
58
Using the BIOS Setup Program
Peripheral Configuration Submenu
Main Advanced Security Power
Peripheral Configuration
Boot Exit
Serial Port A
Parallel Port
Mode
LAN Device
Audio
[Auto]
[Auto]
[Bi-directional]
[Enabled]
[Enabled]
m o
n p
Enter
F1
P9
F10
ESC
Select Screen
Select Item
Select ` Sub-Menu
General Help
Setup Defaults
Save and Exit
Exit
Table 19. Peripheral Configuration Submenu
Feature
Options
Description
Serial Port A
• Disabled
Configures serial port A.
• Enabled
• Auto (default)
Auto assigns the first free COM port, normally COM1,
the address 3F8h, and the interrupt IRQ4.
An * (asterisk) displayed next to an address indicates
a conflict with another device.
Base I/O Address
• 3F8 (default)
• 2F8
• 3E8
Specifies the base I/O address for serial port A, if
serial port A is Enabled.
(This feature is present
only when Serial Port A
is set to Enabled)
• 2E8
Interrupt
• IRQ 3
• IRQ 4 (default)
Specifies the interrupt for serial port A, if serial port A
is Enabled.
(This feature is present
only when Serial Port A
is set to Enabled)
Parallel Port
• Disabled
Configures the parallel port.
• Enabled
• Auto (default)
Auto assigns LPT1 the address 378h and the
interrupt IRQ7.
An * (asterisk) displayed next to an address indicates
a conflict with another device.
continued
59
Intel Desktop Boards D865GBF/D865GLC Product Guide
Table 19. Peripheral Configuration Submenu (continued)
Feature
Options
Description
Mode
• Output only
• Bi-directional (default)
• EPP
Selects the mode for the parallel port. Not available
if the parallel port is disabled.
Output Only operates in AT*-compatible mode.
Bi-directional operates in PS/2-compatible mode.
• ECP
EPP is Extended Parallel Port mode, a high-speed
bi-directional mode.
ECP is Enhanced Capabilities Port mode, a high-
speed bi-directional mode.
Base I/O Address
• 378 (default)
• 278
Specifies the base I/O address for the parallel port,
if Parallel Port is Enabled.
(This feature is present
only when Parallel Port
is set to Enabled)
Interrupt
• IRQ 5
• IRQ 7 (default)
Specifies the interrupt for the parallel port, if Parallel
Port is Enabled.
(This feature is present
only when Parallel Port
is set to Enabled)
LAN Device
• Disabled
• Enabled (default)
Enables or disables the LAN device.
Enables or disables onboard audio.
(This feature is present
only when there is
onboard LAN)
Audio
• Disabled
• Enabled (default)
60
Using the BIOS Setup Program
ATA/IDE Configuration Submenu
Main Advanced Security Power
IDE Configuration
Boot Exit
ATA/IDE Configuration
Legacy IDE Channels
PCI IDE Bus Master
Hard Disk Pre-Delay
[Legacy]
[PATA Pri and Sec]
[Enabled]
[Disabled]
` [PATA Primary Master :
xxxxxxx]
` [PATA Primary Slave
` [PATA Secondary Master :
:
Not Detected]
xxxxxxx]
` [PATA Secondary Master :
Xxxxxxx]
m o
Select Screen
Select Item
Select ` Sub-Menu
General Help
Setup Defaults
Save and Exit
Exit
n p
Enter
F1
P9
F10
ESC
Table 20. ATA/IDE Configuration Submenu
Feature
Options
Description
ATA/IDE Configuration • Disabled
Specifies the integrated IDE controller.
Disabled disables the integrated IDE controller.
Legacy enables up to two IDE channels for OS
requiring legacy IDE operation.
• Legacy
• Enhanced (default)
Enhanced all SATA and PATA resources
Legacy IDE Channels • PATA Pri only
Configures PATA and SATA resources for OS
requiring legacy IDE operation.
• PATA Sec only
• PATA PRI and Sec (default)
• SATA P0/P1 only
• SATA P0/P1, PATA Sec
• SATA P0/P1, PATA Pri
PCI IDE Bus Master
Hard Disk Pre-Delay
• Disabled
• Enabled (default)
• Disabled (default)
• 3 Seconds
• 6 Seconds
Allows a PCI device to initiate a transaction as
a master.
Specifies the hard disk drive pre-delay. Causes
the BIOS to insert a delay before attempting to
detect IDE drives in the system.
• 9 Seconds
• 12 Seconds
• 15 Seconds
• 21 Seconds
• 30 Seconds
61
Intel Desktop Boards D865GBF/D865GLC Product Guide
PATA and SATA Submenus
Main Advanced Security Power Boot Exit
` [SATA Port-0
:
Xxxxxxxx
]
Type
[Auto]
[Auto]
Maximum Capacity
Configuration Options
Selected by BIOS
LBA Mode :
Block Mode:
PIO Mode :
Ultra DMA :
Cable Detected :
[Supported]
16 sectors
Mode 4
Mode 6
Serial
m o
n p
Enter
F1
P9
F10
ESC
Select Screen
Select Item
Select ` Sub-Menu
General Help
Setup Defaults
Save and Exit
Exit
There are four IDE submenus: Primary master, primary slave, secondary master, and secondary
Table 21. SATA and PATA Submenus
Feature
Options
Description
Drive Installed
Type
None
Displays the type of drive installed.
Specifies the IDE configuration mode for IDE devices.
Auto fills-in capabilities from ATA/ATAPI device.
User allows capabilities to be changed.
Displays the capacity of the drive.
Specifies LBA mode control.
• Auto (default)
• User
Maximum Capacity None
LBA Mode Control None
(Note)
Block Mode
• Disabled
Check the hard disk drive’s specifications for optimum
setting.
• Auto (default)
PIO Mode
(Note)
• Auto (default)
Specifies the PIO mode.
• 0
• 1
• 2
• 3
• 4
continued
62
Using the BIOS Setup Program
Feature
Options
Description
DMA Mode
• Auto (default)
• SWDMA 0
• SWDMA 1
• SWDMA 2
• MWDMA 0
• MWDMA 1
• MWDMA 2
• UDMA 0
• UDMA 1
• UDMA 2
• UDMA 3
• UDMA 4
• UDMA 5
• Auto (default)
• Disable
Specifies the Ultra DMA mode for the drive.
S.M.A.R.T.
Self-monitoring analysis and reporting technology.
• Enable
Cable Detected
(Note)
None
Displays the type of cable connected to the IDE interface:
40-conductor or 80-conductor (for ATA-66/100 devices) or
Serial ATA.
Note: These configuration options appear only if an IDE device is installed.
63
Intel Desktop Boards D865GBF/D865GLC Product Guide
Diskette Configuration Submenu
Main
Advanced
Security
Power
Boot
Exit
Diskette Configuration
Diskette Controller
Floppy A
[Enabled]
[1.44/1.25MB 3½"]
[Disabled]
Diskette Write Protect
m o
n p
Enter
F1
P9
F10
ESC
Select Screen
Select Item
Select ` Sub-Menu
General Help
Setup Defaults
Save and Exit
Exit
Table 22. Diskette Configuration Submenu
Feature
Options
Description
Diskette Controller
• Disabled
Configures the integrated floppy controller.
• Enabled (default)
• Disabled
Floppy A
Selects the floppy drive type.
• 360 KB 5¼”
• 1.2 MB 5¼”
• 720 KB 3½”
• 1.44 MB 3½” (default)
• 2.88 MB 3½”
• Disabled (default)
• Enabled
Diskette Write Protect
Disables or enables diskette drive write protection.
64
Using the BIOS Setup Program
Event Log Configuration Submenu
Main
Advanced
Security
Power
Boot
Exit
Event Log Configuration
Event Log
[Space Available]
View Event Log
Clear Event Log
Event Logging
ECC Event Logging
[Enabled]
[Enabled]
m o
n p
Enter
F1
P9
F10
ESC
Mark Events As Read
Select Screen
Select Item
Select ` Sub-Menu
General Help
Setup Defaults
Save and Exit
Exit
Table 23. Event Log Configuration Submenu
Feature
Options
Description
Event Log
No options
Indicates if there is space available in the event log.
Displays the contents of the DMI event log.
Discards all events in the event log.
Enables or disables event logging.
View Event Log
Clear Event Log
Event Logging
[Enter]
No options
• Disabled
• Enabled (default)
• Disabled
• Enabled (default)
ECC Event Logging
Mark Events As Read
Enabled allows logging of DMI events.
[Enter]
Marks all DMI events in the event log as read.
65
Intel Desktop Boards D865GBF/D865GLC Product Guide
Video Configuration Submenu
Main
Advanced
Security
Power
Boot
Exit
Video Configuration
AGP Aperture Size
Primary Video Adapter
Frame Buffer Size
[ 64MB]
[AGP]
[1MB]
m o
n p
Enter
Select Screen
Select Item
Select ` Sub-
Menu
F1
P9
F10
ESC
General Help
Setup Defaults
Save and Exit
Exit
Table 24. Video Configuration Submenu
Feature
Options
Description
AGP Aperture Size
• 4 MB
• 8 MB
Amount of system memory available for direct access by
the graphics device.
• 16 MB
• 32 MB
• 64 MB (default)
• 128 MB
• 256 MB
• AGP (default)
• PCI
Primary Video Adapter
Frame Buffer Size
Allows selecting an AGP or PCI video controller as the
display device that will be active when the system boots.
• 512 KB
• 1 MB (default)
• 8 MB
Controls how much system RAM is reserved for use by
the internal graphics device.
66
Using the BIOS Setup Program
USB Configuration Submenu
Main
Advanced
Security
Power
Boot
Exit
USB Configuration
High-Speed USB
Legacy USB Support
[Enabled]
[Enabled]
m o
n p
Enter
F1
P9
F10
ESC
Select Screen
Select Item
Select ` Sub-Menu
General Help
Setup Defaults
Save and Exit
Exit
Table 25. USB Configuration Submenu
Feature
Options
Description
High Speed USB
• Disabled
Disable this option when a USB 2.0 driver is not
available.
• Enabled (default)
• Disabled
Legacy USB Support
Enables support for legacy USB.
• Enabled (default)
67
Intel Desktop Boards D865GBF/D865GLC Product Guide
Chipset Configuration Submenu
Main
Advanced
Security
Power
Boot
Exit
Chipset Configuration
Setup Warning:
Setting items on this screen to incorrect values
may cause your system to malfunction!
ISA Enable Bit
PCI Latency Timer
CSA Device
[Enabled]
[32]
[Auto]
Do you wish to continue?
Burn-In Mode
[Continue]
[Default]
m o
n p
Enter
F1
P9
F10
ESC
Select Screen
Select Item
Select ` Sub-Menu
General Help
Setup Defaults
Save and Exit
Exit
Extended Configuration
Chipset Memory Timing Control
Graphics Core Frequency
SDRAM Frequency
[Default]
[Auto]
[Auto]
Table 26. Chipset Configuration Submenu
Feature
Options
Description
ISA Enable Bit
• Enabled (default)
• Disabled
• 32 (default)
• 64
Some older expansion devices require this option
to be enabled.
PCI Latency Timer
Set PCI latency time.
• 96
• 128
• 160
• 192
• 224
• 248
CSA Device
• Auto (default)
• Disable
Do you wish to continue? • No (default)
• Continue
Burn-In Mode
• Default (default)
• -2.0%
Alters host and I/O clock frequencies.
• -1.0%
• +1.0%
• +2.0%
• +3.0%
• +4.0%
continued
68
Using the BIOS Setup Program
Table 25. Chipset Configuration Submenu (continued)
Feature
Options
Description
Extended Configuration
• Default (default)
• User Defined
Chooses the default or user defined settings for
the extended configuration options.
Graphics Core Frequency • Auto (default)
• 266 MHz
Allows override of detected graphics core
frequency value.
• 333-320 MHz
SDRAM Frequency
• Auto (default)
• 266 MHz
Allows override of detected memory frequency
value.
• 333 MHz
• 400 MHz
SDRAM Timing Control
• Auto (default)
• Manual – Aggressive
• Manual – User Defined
Auto allows timings to be programmed according
to the memory detected.
Manual – Aggressive selects the most aggressive
user defined timings.
Manual – User Defined allows manual override of
detected SDRAM settings.
CPC Override
• Auto (default)
• Enabled
• Disabled
Controls Command Per Clock/1n rule mode.
When enabled, allows DRAM controller to attempt
Chip Select assertions in two consecutive
common clocks.
SDRAM RAS Act. To Pre. • 8 (default)
Selects length of time from read to pre-change.
Corresponds to tRAS, min.
• 7
• 6
• 5
SDRAM CAS# Latency
• 2.0
• 2.5
• 3.0 (default)
• 4
• 3 (default)
• 2
Selects the number of clock cycles required to
address a column in memory. Corresponds
to CL.
SDRAM RAS# to CAS#
delay
Selects the number of clock cycles between
addressing a row and addressing a column.
Corresponds to tRCD.
SDRAM RAS# Precharge • 4
• 3 (default)
• 2
Selects the length of time required before
accessing a new row.
69
Intel Desktop Boards D865GBF/D865GLC Product Guide
Fan Control Submenu
Main
Advanced
Security
Power
Boot
Exit
Fan Control Configuration
Setup Warning:
These options will not take effect until power has
been completely removed from the system. After
saving the BIOS settings and turning the system
off, unplug the power cord from the system and wait
for at least 30 seconds before reapplying power and
turning the system back on.
m o
n p
Enter
F1
P9
F10
ESC
Fan Control
Lowest Fan Speed
[Enabled]
[Slow]
Select Screen
Select Item
Select ` Sub-Menu
General Help
Setup Defaults
Save and Exit
Exit
Table 27. Hardware Management
Feature
Options
Description
Fan Control
• Disabled
Disables or enables system fan control.
• Enabled (default)
• Slow (default)
• Off
Lowest Fan Speed
This option defines the fan speed at the lowest system
temperature.
Slow allows the fans to continue to run at a reduced speed
at low system temperatures.
Off turns off the fans at low system temperatures.
70
Using the BIOS Setup Program
Hardware Monitoring Submenu
Main
Advanced
Security
Power
Boot
Exit
Hardware Monitoring
Note: These measurements are approximate and
should not be used for validation purposes.
Processor Zone Temperature 44oC/111oF
System Zone 1 Temperature
System Zone 2 Temperature
37oC/98oF
35oC/95oF
Processor Fan Speed
Rear Fan Speed (J1B1)
Rear Fan Speed (J5B1)
Front Fan Speed
2394 RPM
0 RPM
0 RPM
m o
n p
Enter
F1
P9
F10
ESC
0 RPM
Select Screen
Select Item
Select ` Sub-Menu
General Help
Setup Defaults
Save and Exit
Exit
+1.5Vin
Vccp
+3.3Vin
+5Vin
1.480 V
1.447 V
3.258 V
5.026 V
11.625 V
12Vin
Table 28. Hardware Monitoring Submenu
Feature
Options
Description
Processor Zone Temperature
System Zone 1 Temperature
System Zone 2 Temperature
Processor Fan Speed
Rear Fan Speed
No option
No option
No option
No option
No option
No option
No option
Displays processor zone temperature.
Displays system zone 1 temperature.
Displays system zone 2 temperature.
Displays processor fan speed.
Displays rear fan speed.
VREG Fan Speed
Displays VREG fan speed.
Front Fan Speed
Displays front fan speed.
71
Intel Desktop Boards D865GBF/D865GLC Product Guide
Security Menu
Main Advanced Security Power Boot Exit
Supervisor Password :
User Password
Not Installed
Not Installed
:
Set Supervisor Password
Set User Password
Chassis Intrusion
[Disabled]
m o
n p
Enter
F1
P9
F10
ESC
Select Screen
Select Item
Select ` Sub-Menu
General Help
Setup Defaults
Save and Exit
Exit
Table 29. Security Menu
If no password entered previously:
Feature
Options
Description
Supervisor Password
User Password
No options
No options
Reports if there is a supervisor password set.
Reports if there is a user password set.
Set Supervisor Password
Password can be up to seven Specifies the supervisor password.
alphanumeric characters.
Set User Password
Password can be up to seven Specifies the user password.
alphanumeric characters.
Clear User Password
(Note 1)
• Yes (default)
• No
Clears the user password.
User access Level
(Note 2)
• Limited
Sets BIOS Setup Utility access rights for
user level.
• No access
• View Only
• Full (default)
• Disabled (default)
• Enabled
Chassis Intrusion
Notes:
Enables or disables the chassis intrusion
feature.
1. This feature appears only if a user password has been set.
2. This feature appears only if both a user password and a supervisor password have been set.
72
Using the BIOS Setup Program
Power Menu
Main
Advanced
Security
Power
Boot
Exit
` ACPI
After Power Failure
[Last State]
The options below are not related to ACPI and may
be ignored when shutting down using an ACPI OS.
Wake on PCI PME
[Stay Off]
m o
Select Screen
Select Item
Select ` Sub-Menu
General Help
Setup Defaults
Save and Exit
Exit
n p
Enter
F1
P9
F10
ESC
Table 30. Power Menu
Feature
Options
Description
ACPI
No Options
When selected, displays the ACPI submenu.
After Power Failure
• Stay Off
Determines the mode of operation if a power loss
occurs.
• Last State (default)
• Power On
Stay Off keeps the power off until the power button is
pressed.
Last State restores the previous power state before
power loss occurred.
Power On restores power to the computer.
Wake on PCI PME
• Stay Off (default)
Determines how the system responds to a PCI-PME
wake up event.
• Power-On
73
Intel Desktop Boards D865GBF/D865GLC Product Guide
ACPI Submenu
Main Advanced Security Power Boot Exit
Advanced Configuration and Power Interface
S1 is the safest mode
but consumes more power.
S3 consumes low power
but drivers may not
support this state.
ACPI Suspend State
Wake on LAN from S5
[S1 State]
[Stay Off]
m o
n p
Enter
F1
P9
F10
ESC
Select Screen
Select Item
Select ` Sub-Menu
General Help
Setup Defaults
Save and Exit
Exit
Table 31. ACPI Submenu
Feature
Options
Description
ACPI Suspend Mode
• S1 State (default)
• S3 State
Specifies the ACPI sleep state.
Wake on LAN* from S5 • Stay Off (default)
In ACPI soft-off mode only, determines how the
system responds to a LAN wake up event when the
system is in the ACPI soft-off mode.
• Power On
74
Using the BIOS Setup Program
Boot Menu
Main Advanced Security Power Boot Exit
Silent BOOT
[Enabled]
[Enabled]
[Enabled]
[Disabled]
[Enabled]
Intel ® Rapid BIOS Boot
Scan User Flash Area
PXE Boot to LAN
USB Boot
` Boot Device Priority
` Hard Disk Drives
` Removable Devices
` ATAPI CD-ROM Drives
m o
Select Screen
Select Item
Select ` Sub-Menu
General Help
Setup Defaults
Save and Exit
Exit
n p
Enter
F1
P9
F10
ESC
Table 32. Boot Menu
Feature
Options
Description
Silent Boot
• Disabled
Disabled displays normal POST messages.
• Enabled (default) Enabled displays OEM logo instead of POST messages.
Intel® Rapid BIOS Boot
Scan User Flash Area
PXE Boot to LAN
USB Boot
• Disabled
• Enabled (default)
• Disabled
Allows BIOS to skip certain tests while booting.
Enables the BIOS to scan the flash ROM for user binary
files that are executed at boot time.
• Enabled (default)
• Disabled (default) Disables or enables PXE boot to LAN.
• Enabled
• Disabled
Disables or enables booting to USB boot devices.
• Enabled (default)
No options
Boot Device Priority
Hard Disk Drives
Specifies the boot sequence from the available types of
boot devices.
No options
No options
Specifies the boot sequence from the available hard
disk drives.
Removable Devices
Specifies the boot sequence from the available removable
devices.
ATAPI CD-ROM Drives No options
Specifies the boot sequence from the available ATAPI
CD-ROM drives.
75
Intel Desktop Boards D865GBF/D865GLC Product Guide
Boot Device Priority Submenu
Main Advanced Security Power Boot
Exit
Specifies the boot
sequence from the
available devices.
1st Boot Device
2nd Boot Device
3rd Boot Device
[1st FLOPPY DRIVE]
[xxxxxxxxxxx]
[xxxxxxxxxxx]
A device enclosed in
parenthesis has been
disabled in the
corresponding type
menu.
m o
n p
Enter
F1
P9
F10
ESC
Select Screen
Select Item
Select ` Sub-Menu
General Help
Setup Defaults
Save and Exit
Exit
Table 33. Boot Device Priority Submenu
Feature
Options
Description
1st Boot Device • Removable Device Specifies the boot sequence from the available devices. To specify
nd Boot Device • Hard Drive
rd Boot Device • ATAPI CD-ROM
• Disabled
boot sequence:
2
3
1. Select the boot device with <↑> or <↓>.
2. Press <Enter> to set the selection as the intended boot device.
The operating system assigns a drive letter to each boot device in
the order listed. Changing the order of the devices changes the
drive lettering. The default settings for the first through final boot
devices are, respectively listed below. The BIOS supports up to
sixteen total boot devices in any combination of the boot device
types below, with respect to these maximums per type.
• Removable Device (maximum of four).
• Hard Drive (maximum of 12).
• ATAPI CD-ROM (maximum of four).
• A device enclosed in parenthesis has been disabled in the
corresponding type menu.
76
Using the BIOS Setup Program
Hard Disk Drives Submenu
Main
Advanced Security Power Boot Exit
Specifies the boot
sequence from the
available devices.
Select the boot device
with UpArrow or
1st Drive
2nd Drive
3rd Drive
4th Drive
[xxxxxxxxxxxxx]
[xxxxxxxxxxxxx]
[xxxxxxxxxxxxx]
[xxxxxxxxxxxxx]
DownArrow key. Press
Enter to set the
selections as the
intended boot device.
ARMD = ATAPI Removable
Media Device.
m o
n p
Enter
F1
P9
F10
ESC
Select Screen
Select Item
Select ` Sub-Menu
General Help
Setup Defaults
Save and Exit
Exit
Table 34. Hard Disk Drives Submenu
Feature
Options
Description
1st Hard Disk Drive
Dependent on installed Specifies the boot sequence from the available hard disk
(Note)
hard drives
drives. To specify boot sequence:
1. Select the boot device with <↑> or <↓>.
2. Press <Enter> to set the selection as the intended
boot device.
Note: This boot device submenu appears only if at least one boot device of this type is installed. This list will display up to
12 hard disk drives, the maximum number of hard disk drives supported by the BIOS.
77
Intel Desktop Boards D865GBF/D865GLC Product Guide
Removable Devices Submenu
Main Advanced Security Power Boot Exit
Specifies the boot
sequence from the
available devices.
Select the boot device
with UpArrow or
1st Drive
[1st FLOPPY DRIVE]
DownArrow key. Press
Enter to set the
selections as the
intended boot device.
ARMD = ATAPI Removable
Media Device.
m o
n p
Enter
F1
P9
F10
ESC
Select Screen
Select Item
Select ` Sub-Menu
General Help
Setup Defaults
Save and Exit
Exit
Table 35. Removable Devices Submenu
Feature
Options
Description
1st Removable Device
(Note)
Dependent on installed
removable devices
Specifies the boot sequence from the available
removable devices. To specify boot sequence:
1. Select the boot device with <↑> or <↓>.
2. Press <Enter> to set the selection as the
intended boot device.
Note: This boot device submenu appears only if at least one boot device of this type is installed. This list will
display up to four removable devices, the maximum number of removable devices supported by the BIOS.
78
Using the BIOS Setup Program
ATAPI CD-ROM Drives
Main Advanced Security Power Boot Exit
Specifies the boot
sequence from the
available devices.
Select the boot device
with UpArrow or
1st Drive
2nd Drive
[xxxxxxx]
[xxxxxxx]
DownArrow key. Press
Enter to set the
selections as the
intended boot device.
ARMD = ATAPI Removable
Media Device.
m o
n p
Enter
F1
P9
F10
ESC
Select Screen
Select Item
Select ` Sub-Menu
General Help
Setup Defaults
Save and Exit
Exit
Table 36. ATAPI CD-ROM Drives Submenu
Feature
1st ATAPI CD-ROM Drive Dependent on installed
ATAPI CD-ROM drives
Options
Description
Specifies the boot sequence from the available
ATAPI CD-ROM drives. To specify boot sequence:
(Note)
1. Select the boot device with <↑> or <↓>.
2. Press <Enter> to set the selection as the
intended boot device.
Note: This boot device submenu appears only if at least one boot device of this type is installed. This list will display
up to four ATAPI CD-ROM drives, the maximum number of ATAPI CD-ROM drives supported by the BIOS.
79
Intel Desktop Boards D865GBF/D865GLC Product Guide
Exit Menu
Main Advanced Security Power Boot Exit
Exit Saving Changes
Exit Discarding Changes
Load Optimal Defaults
Load Custom Defaults
Save Custom Defaults
Discard Changes
m o
n p
Enter
F1
P9
F10
ESC
Select Screen
Select Item
Select ` Sub-Menu
General Help
Setup Defaults
Save and Exit
Exit
and saving defaults.
Table 37. Exit Menu
Feature
Description
Exit Saving Changes
Exits and saves the changes in CMOS SRAM.
Exit Discarding Changes Exits without saving any changes made in the BIOS Setup program.
Load Optimal Defaults
Load Custom Defaults
Save Custom Defaults
Loads optimal defaults.
Loads the custom defaults for Setup options.
Saves the current values as custom defaults. Normally, the BIOS reads the
Setup values from flash memory. If this memory is corrupted, the BIOS reads the
custom defaults. If no custom defaults are set, the BIOS reads the factory
defaults.
Discard Changes
Discards changes without exiting Setup. The option values present when the
computer was turned on are used.
80
5 Technical Reference
Board Connectors
This chapter shows the location of the:
•
•
•
Back panel connectors
Audio connectors
Add-in board and peripheral interface connectors
CAUTION
Many of the midboard and front panel connectors provide operating voltage (+5 V dc and
+12 V dc, for example) to devices inside the computer chassis, such as fans and internal
peripherals. These connectors are not overcurrent protected. Do not use these connectors for
powering devices external to the computer chassis. A fault in the load presented by the external
devices could cause damage to the computer, the interconnecting cable, and the external devices
themselves.
81
Intel Desktop Boards D865GBF/D865GLC Product Guide
Back Panel Connectors
NOTE
The line out connector, located on the back panel, is designed to power either headphones or
amplified speakers only. Poor audio quality may occur if passive (non-amplified) speakers are
connected to this output.
Figure 18 shows the back panel connectors.
Line
In
USB 2.0
USB 2.0
Devices
Devices
OM15235
Figure 18. Back Panel Connectors
82
Technical Reference
Audio Connectors
Figure 13 shows the approximate location of the audio connectors.
C
B
A
1
3
5
7
9
2
4
6
1
2
1
2
3
4
3
4
10
J9C1
J9A2
J8B1
OM15236
Item
Description
A
B
C
CD-ROM (ATAPI-style)
Front panel audio
Auxiliary line in (ATAPI-style)
Figure 19. Audio Connectors
83
Intel Desktop Boards D865GBF/D865GLC Product Guide
Add-In Card and Peripheral Interface Connectors
Figure 20 shows the PCI bus add-in card and peripheral interface connectors for Desktop Board
D865GBF. Desktop Board D865GLC has three PCI bus add-in card connectors.
A
B
C
D
E
F
G
I
H
J
OM15238
Item
Description
Item
Description
A
B
C
D
E
PCI bus add-in card connector 6
PCI bus add-in card connector 5
PCI bus add-in card connector 4
PCI bus add-in card connector 3
PCI bus add-in card connector 2
(SMBus routed)
F
G
H
I
PCI bus add-in card connector 1
AGP
Floppy drive
Primary IDE
Secondary IDE
J
Figure 20. PCI Bus Add-in Card and Peripheral Interface Connectors
84
Technical Reference
Desktop Board Resources
Memory Map
Table 38. System Memory Map
Address Range (decimal) Address Range (hex) Size
Description
1024 K - 4194304 K
960 K - 1024 K
896 K - 960 K
100000 - FFFFFFFF
F0000 - FFFFF
E0000 - EFFFF
C8000 - DFFFF
4095 MB Extended Memory
64 KB
64 KB
96 KB
Runtime BIOS
Reserved
800 K - 896 K
Available high DOS memory (open to the
PCI bus)
640 K - 800 K
639 K - 640 K
A0000 - C7FFF
9FC00 - 9FFFF
160 KB
1 KB
Video memory and BIOS
Extended BIOS data (movable by
memory manager software)
512 K - 639 K
0 K - 512 K
80000 - 9FBFF
00000 - 7FFFF
127 KB
512 KB
Extended conventional memory
Conventional memory
DMA Channels
Table 39. DMA Channels
DMA Channel Number
Data Width
8 or 16 bits
8 or 16 bits
8 or 16 bits
8 or 16 bits
8 or 16 bits
16 bits
System Resource
0
1
2
3
4
5
6
7
Parallel port
Floppy drive
Parallel port (for ECP or EPP)
DMA controller
Open
16 bits
Open
16 bits
Open
85
Intel Desktop Boards D865GBF/D865GLC Product Guide
Interrupts
Table 40. Interrupts
IRQ
NMI
0
System Resource
I/O channel check
Reserved, interval timer
1
Reserved, keyboard buffer full
2
Reserved, cascade interrupt from slave PIC
3
COM2*
4
COM1*
5
LPT2 (Plug and Play option) **
6
Floppy drive controller
7
LPT1*
8
Real time clock
9
**
10
11
12
13
14
15
**
**
Onboard mouse port (if present, else user available)
Reserved, math coprocessor
Primary IDE (if present, else user available)
Secondary IDE (if present, else user available)
* Default, but can be changed to another IRQ.
** Dynamically allocated for all PCI/AGP devices and slots.
86
A Error Messages and Indicators
Desktop Board D865GBF/D865GLC reports POST errors in two ways:
•
•
By sounding a beep code
By displaying an error message on the monitor
BIOS Beep Codes
followed by two short tones) during POST if the video configuration fails (a faulty video card or no
card installed) or if an external ROM module does not properly checksum to zero.
Table 41. Beep Codes
Number of Beeps
Description
1
Refresh failure
2
Parity cannot be reset
3
First 64 K memory failure
4
Timer not operational
5
Processor failure (Reserved; not used)
8042 GateA20 cannot be toggled (memory failure or not present)
Exception interrupt error
6
7
8
Display memory R/W error
9
(Reserved; not used)
10
11
CMOS Shutdown register test error
Invalid BIOS (such as, POST module not found)
87
Intel Desktop Boards D865GBZ/D865GLC Product Guide
BIOS Error Messages
When a recoverable error occurs during the POST, the BIOS displays an error message describing
the problem.
Table 42. BIOS Error Messages
Error Message
Explanation
GA20 Error
An error occurred with Gate-A20 when switching to protected
mode during the memory test.
Pri Master HDD Error
Pri Slave HDD Error
Sec Master HDD Error
Sec Slave HDD Error
Could not read sector from corresponding drive.
Pri Master Drive - ATAPI Incompatible
Pri Slave Drive - ATAPI Incompatible
Sec Master Drive - ATAPI Incompatible
Sec Slave Drive - ATAPI Incompatible
Corresponding drive is not an ATAPI device. Run Setup to make
sure device is selected correctly.
A: Drive Error
B: Drive Error
No response from the diskette drive.
CMOS Battery Low
The battery may be losing power. Replace the battery soon.
CMOS Display Type Wrong
The display type is different than what has been stored in CMOS.
Check Setup to make sure type is correct.
CMOS Checksum Bad
CMOS Settings Wrong
CMOS Date/Time Not Set
The CMOS checksum is incorrect. CMOS memory may have been
corrupted. Run Setup to reset values.
CMOS values are not the same as the last boot. These values
have either been corrupted or the battery has failed.
The time and/or date values stored in CMOS are invalid. Run
Setup to set correct values.
DMA Error
Error during read/write test of DMA controller.
Error occurred trying to access diskette drive controller.
Error occurred trying to access hard disk controller.
NVRAM is being checked to see if it is valid.
NVRAM was invalid and has been updated.
FDC Failure
HDC Failure
Checking NVRAM.....
Update OK!
Updated Failed
Keyboard Is Locked
NVRAM was invalid but was unable to be updated.
The system keyboard lock is engaged. The system must be
unlocked to continue to boot.
Keyboard Error
Error in the keyboard connection. Make sure keyboard is
connected properly.
KB/Interface Error
Keyboard interface test failed.
continued
88
Error Messages and Indicators
Table 42. BIOS Error Messages (continued)
Error Message
Explanation
Memory Size Decreased
Memory size has decreased since the last boot. If no memory was
removed, then memory may be bad.
Memory Size Increased
Memory Size Changed
Memory size has increased since the last boot. If no memory was
added, there may be a problem with the system.
Memory size has changed since the last boot. If no memory was
added or removed, then memory may be bad.
No Boot Device Available
Off Board Parity Error
System did not find a device to boot.
A parity error occurred on an offboard card. This error is followed
by an address.
On Board Parity Error
Parity Error
A parity error occurred in onboard memory. This error is followed
by an address.
A parity error occurred in onboard memory at an unknown
address.
NVRAM / CMOS / PASSWORD
cleared by Jumper
NVRAM, CMOS, and passwords have been cleared. The system
should be powered down and the jumper removed.
<CTRL_N> Pressed
CMOS is ignored and NVRAM is cleared. User must enter Setup.
89
Intel Desktop Boards D865GBZ/D865GLC Product Guide
90
B Regulatory Compliance
This appendix contains safety standards, electromagnetic compatibility (EMC) regulations, and
product certification markings for Desktop Board D865GBF/D865GLC.
Safety Regulations
Desktop Board D865GBF/D865GLC complies with the safety regulations stated in Table 43 when
correctly installed in a compatible host system.
Table 43. Safety Regulations
Regulation
Title
CSA C22.2 No. 60950/
Bi-National Standard for Safety of Information Technology Equipment
including Electrical Business Equipment. (USA and Canada)
UL 60950, 3rd Edition, 2000
EN 60950, 2nd Edition, 1992
The Standard for Safety of Information Technology Equipment including
(with Amendments 1, 2, 3, and 4) Electrical Business Equipment. (European Union)
IEC 60950, 2nd edition, 1991
The Standard for Safety of Information Technology Equipment including
(with Amendments 1, 2, 3, and 4) Electrical Business Equipment. (International)
EMKO-TSE (74-SEC) 207/94
Summary of Nordic deviations to EN 60950. (Norway, Sweden,
Denmark, and Finland)
EMC Regulations
Desktop Board D865GBF/D865GLC complies with the EMC regulations stated in Table 44 when
correctly installed in a compatible host system.
Table 44. EMC Regulations
Regulation
Title
FCC Class B
Title 47 of the Code of Federal Regulations, Parts 2 and 15, Subpart B,
Radiofrequency Devices. (USA)
ICES-003 (Class B)
Interference-Causing Equipment Standard, Digital Apparatus. (Canada)
EN55022: 1998 (Class B)
Limits and methods of measurement of Radio Interference Characteristics
of Information Technology Equipment. (European Union)
EN55024: 1998
Information Technology Equipment – Immunity Characteristics Limits and
methods of measurement. (European Union)
AS/NZS 3548 (Class B)
Australian Communications Authority, Standard for Electromagnetic
Compatibility. (Australia and New Zealand)
CISPR 22, 3rd Edition,
(Class B)
Limits and methods of measurement of Radio Disturbance Characteristics
of Information Technology Equipment. (International)
CISPR 24: 1997
Information Technology Equipment – Immunity Characteristics – Limits
and Methods of Measurement. (International)
91
Intel Desktop Boards D865GBZ/D865GLC Product Guide
Product Certification Markings
Desktop Board D865GBF/D865GLC has the following product certification markings:
•
UL joint US/Canada Recognized Component mark: consists of small c followed by a stylized
backward UR and followed by a small US. Includes adjacent UL file number for Intel desktop
boards: E210882 (component side).
•
•
•
•
•
•
FCC Declaration of Conformity logo mark for Class B equipment; includes Intel name and
model designation (solder side).
CE mark: declaring compliance to European Union (EU) EMC directive (89/336/EEC) and
Low Voltage directive (73/23/EEC) (component side).
Australian Communications Authority (ACA) C-Tick mark: consists of a stylized C overlaid
with a check (tick) mark (component side), followed by Intel supplier code number, N-232.
Printed wiring board manufacturer’s recognition mark: consists of a unique UL recognized
manufacturer’s logo, along with a flammability rating (94V-0) (solder side).
Battery “+ Side Up” marking: located on the component side of the board in close proximity to
the battery holder.
Korean MIC logo mark: denotes Korean EMC certification (component side). Additional
certification information is provided below:
1. Product Name (model)
2. Certificate ID
3. Applicant: Intel Korea Ltd.
4. Date of manufacture as separate marking on product
5. Manufacturer (country of origin)
Korean MIC logo mark for Desktop Board D865GLC
Korean MIC logo mark for Desktop Board D865GBF
92
Regulatory Compliance
•
Korean Class B statement translated as follows: this is household equipment that is certified to
comply with EMC requirements. You may use this equipment in residential environments and
other non-residential environments.
93
Intel Desktop Boards D865GBZ/D865GLC Product Guide
94
|