Intel® Desktop Board D510MO
Product Guide
Order Number: E74518-001
Preface
This Product Guide gives information about board layout, component installation, and
regulatory requirements for Intel® Desktop Board D510MO.
Intended Audience
The Product Guide is intended for technically qualified personnel. It is not intended for
general audiences.
Intended Uses
All Intel® Desktop Boards are evaluated as Information Technology Equipment (I.T.E.)
for use in personal computers (PC) for installation in homes, offices, schools, computer
rooms, and similar locations. The suitability of this product for other PC or embedded
non-PC applications or other environments, such as medical, industrial, alarm systems,
test equipment, etc. may not be supported without further evaluation by Intel.
Document Organization
The chapters in this Product Guide are arranged as follows:
1 Desktop Board Features: a summary of product features
2 Installing and Replacing Desktop Board Components: instructions on how to install
the Desktop Board and other hardware components
3 Updating the BIOS: a description of how to update the BIOS
A BIOS Error Messages: information about BIOS error messages and beep codes
B Regulatory Compliance: safety and EMC regulations and product certifications
Conventions
The following conventions are used in this manual:
CAUTION
Cautions warn the user about how to prevent damage to hardware or loss of data.
NOTE
Notes call attention to important information.
iii
Intel Desktop Board D510MO Product Guide
Terminology
The table below gives descriptions to some common terms used in the product guide.
Term
GB
Description
Gigabyte (1,073,741,824 bytes)
Gigahertz (one billion hertz)
Kilobyte (1024 bytes)
GHz
KB
MB
Megabyte (1,048,576 bytes)
Megabit (1,048,576 bits)
Megahertz (one million hertz)
Mbit
MHz
iv
Contents
Desktop Board Components.................................................................................11
Processor..........................................................................................................13
System Memory.................................................................................................13
Integrated Graphics Subsystem ...........................................................................14
Intel® NM10 Express Chipset ...............................................................................14
Operating System Support ..................................................................................14
Onboard Audio Subsystem ..................................................................................14
Legacy Input/Output (I/O) Controller....................................................................16
LAN Subsystem .................................................................................................16
USB 2.0 Support................................................................................................17
SATA Interface ..................................................................................................17
Expandability.....................................................................................................17
BIOS................................................................................................................18
Security Passwords.....................................................................................18
Power Management Features...............................................................................19
ACPI.........................................................................................................19
Hardware Support ......................................................................................19
Battery.............................................................................................................22
Real-Time Clock.................................................................................................22
Before You Begin ...............................................................................................23
Installation Precautions.......................................................................................25
Installing the I/O Shield......................................................................................26
Installing and Removing the Desktop Board...........................................................27
Installing and Removing Memory..........................................................................27
Installing DIMMs ........................................................................................28
Removing DIMMs........................................................................................30
Connecting SATA Drives......................................................................................30
Connecting to the Internal Headers ......................................................................34
Connecting to the Serial Headers..................................................................36
Connecting a Chassis Fan....................................................................................39
Connecting the Power Supply Cable......................................................................40
v
Intel Desktop Board D510MO Product Guide
Setting the BIOS Configuration Jumper .................................................................41
Clearing Passwords.....................................................................................42
Replacing the Battery .........................................................................................43
Obtaining the BIOS Update File ....................................................................50
Recovering the BIOS...................................................................................51
BIOS Beep Codes...............................................................................................53
BIOS Front-panel Power LED Blink Codes ..............................................................54
POST Error Messages..........................................................................................54
Safety Standards ...............................................................................................55
Place Battery Marking .................................................................................55
Product Ecology Statements ................................................................................57
Recycling Considerations .............................................................................57
Lead-free 2LI/Pb-free 2LI Board ...................................................................60
EMC Regulations................................................................................................63
Product Certifications..........................................................................................65
Board-Level Certification Markings ................................................................65
vi
Contents
Figures
2. Back Panel Audio Connectors .........................................................................15
3. LAN Status LEDs ..........................................................................................16
4. Location of the Standby Power Indicator ..........................................................20
5. Installing the I/O Shield ................................................................................26
7. Use DDR2 DIMMs .........................................................................................28
8. Installing a DIMM .........................................................................................29
9. Connecting the Serial ATA Cable.....................................................................31
10. Installing a Wireless LAN Card........................................................................32
12. Internal Headers ..........................................................................................34
13. Location of the Chassis Fan Header.................................................................39
14. Connecting a Power Supply Cable ...................................................................40
15. BIOS Configuration Jumper Block....................................................................41
16. Removing the Battery ...................................................................................47
Tables
1. Feature Summary.......................................................................................... 9
3. Audio Jack Support.......................................................................................15
4. LAN Status LEDs ..........................................................................................17
5. ENERGY STAR Requirements..........................................................................22
6. Front Panel Audio Header for Intel HD Audio.....................................................35
7. Front Panel Audio Header for AC ‘97 Audio .......................................................35
8. S/PDIF Header.............................................................................................36
9. Serial Port Headers (COM 1 and COM 2) ..........................................................36
10. Parallel Port Header ......................................................................................36
11. Front Panel Wireless Activity LED Header .........................................................37
12. Front Panel Header Signal Names ...................................................................38
13. Front Panel USB Header ................................................................................38
(or Compatible Device) Support......................................................................39
17. BIOS Beep Codes .........................................................................................53
18. BIOS Front-panel Power LED Blink Codes.........................................................54
19. POST Error Messages....................................................................................54
20. Safety Standards..........................................................................................55
21. Lead-Free Second Level Interconnect Marks .....................................................60
23. EMC Regulations...........................................................................................63
24. Product Certification Markings ........................................................................65
vii
Intel Desktop Board D510MO Product Guide
viii
1 Desktop Board Features
This chapter briefly describes the main features of Intel® Desktop Board D510MO.
Table 1 summarizes the features of the Desktop Board.
Table 1. Feature Summary
Form Factor
Processor
Mini-ITX ([170 millimeters [6.7 inches] x 170 millimeters [6.7 inches])
Passively-cooled, soldered-down dual-core Intel® Atom™ processor with
integrated graphics and memory controllers.
Main Memory
• Two 240-pin Double Data Rate 2 (DDR2) Dual Inline Memory Module
(DIMM) sockets with gold-plated contacts
• Support for DDR2 800 MHz and DDR2 667 MHz DIMMs
• Support for up to 4 GB total system memory (2 GB per DIMM
socket)
Intel® NM10 Express Chipset
Chipset
Integrated
Graphics
Intel® Graphics Media Accelerator 3150 (Intel® GMA 3150) integrated
graphics subsystem with support for analog displays (VGA)
RealTek* ALC662 audio codec for 5.1 (6-channel) Intel® High
Definition Audio (Intel® HD Audio) and AC ’97 Audio. Included are:
• Back panel connectors
Audio
• Front panel microphone/headphone header with support for
Intel® HD Audio or AC ’97 Audio
• S/PDIF digital audio header
Expansion
Capabilities
One PCI* bus add-in card connector
One PCI Express* Full-Mini Card slot
Peripheral
Interfaces
• Seven USB 2.0 ports:
― Four back panel ports
― Three front panel ports (via two internal headers; one header
supports an Intel® Z-U130 USB Solid-State Drive (or compatible
device)
• Two Serial ATA (SATA) 3.0 Gb/s connectors (supporting IDE and
ACHI)
Legacy I/O Control
Winbond* W83627TGH-I legacy I/O controller:
• Two serial port headers
• One parallel port header
• PS/2 keyboard and mouse connectors
Hardware Monitor
Subsystem
Hardware monitoring through the Winbond legacy I/O controller,
including:
• Remote thermal sensor
• One 3-pin chassis fan header with speed control
LAN Support
10/100/1000 Mb/s (Gigabit) Ethernet LAN Subsystem using a RealTek*
8111DL Gigabit Ethernet Controller
9
Intel Desktop Board D510MO Product Guide
• Intel® BIOS
BIOS
• Support for Advanced Configuration and Power Interface (ACPI),
Plug and Play, and SMBIOS
Instantly Available
PC Technology
• Support for PCI Local Bus Specification, Revision 2.3
• Support for Advanced Configuration and Power Interface (ACPI)
• Wake on USB, PCI, PCI Express, PS/2, LAN, serial, and front panel
For more information on Intel Desktop Board D510MO consult the following online
resources:
To find information
about…
Visit this World Wide Web site:
Intel Desktop Board
D510MO
Desktop Board Support
Available configurations
for Intel Desktop Board
D510MO
Chipset information
BIOS and driver updates
Integration information
10
Desktop Board Features
Desktop Board Components
Figure 1 shows the location of the major components on Intel Desktop Board D510MO.
Figure 1. Intel Desktop Board D510MO Components
11
Intel Desktop Board D510MO Product Guide
Table 2. Intel Desktop Board D510MO Components
Label
Description
A
B
C
D
E
F
Back panel connectors
Serial header (COM1)
Parallel port header
Serial port (COM 2)
Chassis fan header
Main power connector
Standby power indicator
Processor
G
H
I
Channel A DIMM 0
Channel A DIMM 1
SATA 1
J
K
L
SATA 0
M
N
O
P
Front panel header
Battery
Front panel wireless activity LED header
Intel NM10 Express Chipset
Q
USB front panel header with Intel Z-U130 USB Solid-State Drive (or
compatible device) support
R
S
T
PCI bus connector
PCI Express Mini Card connector
USB front panel header
Front panel audio header
BIOS configuration jumper block
S/PDIF header
U
V
W
12
Desktop Board Features
Processor
Intel Desktop Board D510MO includes a passively-cooled, dual-core Intel Atom
processor with integrated graphics and memory controller. The processor is soldered
to the Desktop Board and is not customer upgradeable.
NOTE
The board is designed to be passively cooled in a properly ventilated chassis. Chassis
venting locations are recommended above the processor heatsink area for maximum
heat dissipation effectiveness.
System Memory
NOTE
To be fully compliant with all applicable Intel® SDRAM memory specifications, the
board should be populated with DIMMs that support the Serial Presence Detect (SPD)
data structure. If your memory modules do not support SPD, you will see a
notification to this effect on the screen at power up. The BIOS will attempt to
configure the memory controller for normal operation.
The Desktop Board has two 240-pin DDR2 DIMM connectors with gold-plated contacts.
It supports:
•
•
•
•
DDR2 800 MHz or DDR2 667 MHz unbuffered, non-registered DIMMs
Serial Presence Detect (SPD) memory only
Non-ECC memory
Up to 4 GB of memory
13
Intel Desktop Board D510MO Product Guide
Integrated Graphics Subsystem
The integrated Intel GMA 3150 graphics controller features the following:
•
•
400 MHz core frequency
High quality texture engine
⎯ DX9.0c* and OpenGL* 1.4 compliant
⎯ Hardware Pixel Shader 2.0
⎯ Vertex Shader Model 2.0
•
3D Graphics Rendering enhancements
⎯ 1.6 dual texture GigaPixel/s max fill rate
⎯ 16-bit and 32-bit color
⎯ Vertex cache
•
•
Video
⎯ Software DVD at 30 fps full screen
⎯ DVMT support up to 256 MB
Supports analog displays up to 2048 x 1536 at 75 Hz refresh (QXGA)
Intel® NM10 Express Chipset
The Intel NM10 Express Chipset is a centralized controller for the board’s I/O paths.
For more information about the Intel NM10 Express Chipset, go to
Operating System Support
The following Microsoft* operating systems are fully supported by the Desktop Board:
•
•
•
Microsoft Windows Vista* Home Basic, SP 1
Microsoft Windows* XP Home, SP 3
Microsoft Windows* 7 Home Basic and Starter
Onboard Audio Subsystem
The Intel Desktop Board D510MO 6-channel (5.1) onboard audio subsystem supports
both Intel HD Audio and AC ’97 Audio. The subsystem is based on the following
components:
•
•
Intel NM10 Express Chipset
RealTek ALC662 audio codec
The subsystem includes the following headers and connectors:
•
Front panel audio header (supports both Intel HD Audio and AC ’97) , including
functionality for:
―
―
Line out (headphones/speaker)
Microphone in
•
•
Three back panel analog audio jacks
Onboard S/PDIF output header (3 pin)
14
Desktop Board Features
The front/back panel audio connectors are configurable through the audio device
Table 3. Audio Jack Support
Audio Jack
Line
In
Line/
Rear Out
Center/
LFE
Microphone
Headphones
Front Out
Front panel – Green
Front panel – Pink
Back panel – Blue
Back panel – Green
Back panel – Pink
No
No
Yes
No
No
Yes
No
No
No
Yes
No
No
No
No
No
No
Yes
No
Yes
No
Yes
No
No
No
Yes
No
No
Yes
No
Yes
Figure 2 shows the default assignment of the back panel audio connectors.
Item Description
A
B
C
Line In
Line Out
Mic In
Figure 2. Back Panel Audio Connectors
NOTE
The back panel audio line out connector is designed to power headphones or amplified
speakers only. Poor audio quality occurs if passive (non-amplified) speakers are
connected to this output.
15
Intel Desktop Board D510MO Product Guide
Legacy Input/Output (I/O) Controller
The legacy I/O controller provides the following:
•
•
Two serial ports (via onboard headers)
One parallel port with Extended Capabilities Port (ECP) and Enhanced Parallel Port
(EPP) support via an onboard headers
•
•
•
•
Serial IRQ interface compatible with serialized IRQ support for PCI systems
PS/2-style keyboard and mouse ports
Intelligent power management, including a programmable wake up event interface
PCI power management support
The BIOS Setup program provides configuration options for the legacy I/O controller.
LAN Subsystem
The LAN subsystem consists of the following:
•
•
Intel NM10 Express Chipset
Realtek 8111DL Gigabit Ethernet Controller for 10/100/1000 Mbits/s Ethernet LAN
connectivity
•
RJ-45 LAN connector with integrated status LEDs
Additional features of the LAN subsystem include:
•
•
•
CSMA/CD protocol engine
LAN connect interface that supports the ethernet controller
PCI bus power management
⎯ Supports ACPI technology
⎯ Supports LAN wake capabilities
LAN drivers are available from Intel’s World Wide Web site at
Two LEDs are built into the RJ-45 LAN connector located on the back panel (see
Figure 3. LAN Status LEDs
16
Desktop Board Features
Table 4 describes the LED states when the board is powered up and the LAN
subsystem is operating.
Table 4. LAN Status LEDs
LED
LED Color
LED State
Blinking
Off
Indicates
Activity (A) Green
N/A
LAN activity is occurring.
10 Mbits/s data rate is selected.
100 Mbits/s data rate is selected.
1000 Mbits/s data rate is selected.
Speed (B)
Green
Yellow
On
On
USB 2.0 Support
The Desktop Board supports up to seven USB 2.0 ports (four ports routed to the back
panel and three ports routed to two front panel USB 2.0 headers). One of the front
panel USB headers supports an Intel Z-U130 USB Solid-State Drive (or compatible
device). The USB 2.0 ports are compatible with USB 1.1 devices. USB 1.1 devices will
function normally at USB 1.1 speeds.
USB 2.0 support requires both an operating system and drivers that fully support
USB 2.0 transfer rates. Disabling High-Speed USB in the BIOS reverts all USB 2.0
ports to USB 1.1 operation. This may be required to accommodate operating systems
that do not support USB 2.0.
NOTE
Computer systems that have an unshielded cable attached to a USB port might not
meet FCC Class B requirements, even if no device or a low-speed USB device is
attached to the cable. Use a shielded cable that meets the requirements for a
full-speed USB device.
SATA Interface
The Desktop Board supports two SATA channels (3.0 Gb/s) that support one device
per channel. The SATA controller supports IDE and ACHI configuration and can
operate in both legacy and native modes.
Expandability
The Desktop Board provides the following expansion capability:
•
One PCI connector. The connector can support either a single PCI add-in card or a
single- or dual-slot PCI riser card.
•
One PCI Express Full-Mini Card slot.
17
Intel Desktop Board D510MO Product Guide
BIOS
The BIOS provides the Power-On Self-Test (POST), the BIOS Setup program, the PCI
and IDE auto-configuration utilities, and the video BIOS.
PCI/PCI Express Auto Configuration
If you install a PCI/PCI Express add-in card in your computer, the PCI/PCI Express
auto-configuration utility in the BIOS automatically detects and configures the
resources (IRQs, DMA channels, and I/O space) for that add-in card. You do not need
to run the BIOS Setup program after you install a PCI/PCI Express add-in card.
Security Passwords
The BIOS includes security features that restrict whether the BIOS Setup program can
be accessed and who can boot the computer. A supervisor password and a user
password can be set for the BIOS Setup and for booting the computer, with the
following restrictions:
•
The supervisor password gives unrestricted access to view and change all Setup
options. If only the supervisor password is set, pressing <Enter> at the password
prompt of Setup gives the user restricted access to Setup.
•
If both the supervisor and user passwords are set, you must enter either the
supervisor password or the user password to access Setup. Setup options are then
available for viewing and changing depending on whether the supervisor or user
password was entered.
•
Setting a user password restricts who can boot the computer. The password
prompt is displayed before the computer is booted. If only the supervisor
password is set, the computer boots without asking for a password. If both
passwords are set, you can enter either password to boot the computer.
18
Desktop Board Features
Power Management Features
Power management is implemented at several levels, including:
•
•
Software support through the Advanced Configuration and Power Interface (ACPI)
Hardware support:
― Power connector
― Fan header
― +5 V standby power indicator LED
― LAN Wake capabilities
― Instantly Available PC technology
― Wake from USB
― Wake from PS/2 devices
― PME# wakeup support
― WAKE# signal wakeup support
― Wake from serial port
ACPI
ACPI gives the operating system direct control over the power management and Plug
and Play functions of a computer. The use of ACPI with the Desktop Board requires an
operating system that provides full ACPI support.
Hardware Support
Fan Header
location of the chassis fan header.
+5 V Standby Power Indicator
CAUTION
If the AC power has been switched off and the standby power indicator is still lit,
disconnect the power cord before installing or removing any devices connected to the
board. Failure to do so could damage the board and any attached devices.
standby power to the system. This includes the DIMM socket and the PCI bus
connector, even though the computer appears to be off.
19
Intel Desktop Board D510MO Product Guide
Figure 4. Location of the Standby Power Indicator
For more information on standby current requirements for the Desktop Board, refer to
the Technical Product Specification on the Intel Desktop D510MO web page at
Instantly Available PC Technology
Instantly Available PC technology enables the board to enter the ACPI S3 (Suspend-to-
RAM) sleep-state. While in the ACPI S3 sleep-state, the computer will appear to be off
(the hard drive(s) and fan will power off, the front panel power LED will blink). When
signaled by a wake-up device or event, the system quickly returns to its last known
state.
The board supports the PCI Bus Power Management Interface Specification. Add-in
boards that also support this specification can participate in power management and
can be used to wake the computer.
The use of Instantly Available PC technology requires operating system support and
PCI 2.3 compliant add-in cards and drivers.
20
Desktop Board Features
LAN Wake Capabilities
The board’s LAN wake capabilities enable remote wake-up of the computer through a
network. The LAN subsystem network adapter monitors network traffic at the Media
Independent Interface. The board supports LAN wake capabilities with ACPI in the
following ways:
•
•
By Ping
By Magic Packet
Upon detecting the configured wake packet type, the LAN subsystem asserts a wake-
up signal that powers up the computer.
Wake from USB
USB bus activity wakes the computer from an ACPI S1 or S3 state.
NOTE
Wake from USB requires the use of a USB peripheral that supports wake from USB.
Wake from PS/2 Device
PS/2 keyboard activity wakes the computer from an ACPI S1, S3, S4, or S5 state.
However, when the computer is in an ACPI S4 or S5 state, the only PS/2 activity that
will wake the computer is the Alt + Print Screen key combination or the Power key
available only on some keyboards.
PME# Wakeup Support
When the PME# signal is asserted on the PCI bus, the computer wakes from an ACPI
S1, S3, S4, or S5 state.
WAKE# Signal Wakeup Support
When the WAKE# signal is asserted on the PCI Express bus, the computer wakes from
an ACPI S1, S3, S4, or S5 state.
Wake from Serial Port
Serial port activity wakes the computer from an ACPI S1 or S3 state.
21
Intel Desktop Board D510MO Product Guide
ENERGY STAR*, e-Standby, and ErP
Compliance
Intel Desktop Board D510MO meets the ENERGY STAR requirements listed in Table 5
when used in corresponding system configurations.
Table 5. ENERGY STAR Requirements
Typical
Electricity
ENERGY STAR
Specification
Required
States
Capability
Adjustments
Consumption
(TEC) Criteria
Computer Type
v4.0
v4.0
Desktop Computer
Idle State
(Cat A)
With and
N/A
without Wake
On LAN (Sleep,
Standby)
Integrated
Computer
Sleep Mode
Standby Level
v5.0
v5.0
Desktop Computer
Off Mode
With and
without
additional
internal storage
Cat A under
“desktop
Sleep Mode
Idle State
Active State
Integrated Desktop
Computer
conventional”
and “desktop
proxying”
operational
mode
weightings
v5.0
Thin Client
Off Mode
With and
N/A
without Wake
On LAN (Sleep,
Standby)
Sleep Mode
Idle State
(Cat B)
For information about ENERGY STAR requirements and recommended configurations,
The Desktop Board also meets the following international requirements:
•
•
Republic of Korea e-Standby program
European Union Energy using Products (EuP) directive
Battery
A coin-cell battery on the Desktop Board keeps the values in CMOS RAM and the clock
replace the battery.
Real-Time Clock
The Desktop Board includes a time-of-day clock and a 100-year calendar. The coin-
cell battery keeps the clock current when the computer is turned off.
22
2 Installing and Replacing Desktop
Board Components
This chapter tells you how to:
•
•
•
•
•
•
•
•
•
•
•
Install the I/O shield
Install and remove the Desktop Board
Install and remove system memory
Connect SATA drives
Install a Wireless LAN card
Install an Intel Z-U130 USB Solid-State Drive (or compatible device)
Connect to internal headers
Connect chassis fan and power supply cables
Set the BIOS configuration jumper
Clear passwords
Replace the battery
Before You Begin
CAUTION
The procedures in this chapter assume familiarity with the general terminology
associated with personal computers and with the safety practices and regulatory
compliance required for using and modifying electronic equipment.
Disconnect the computer from its power source and from any telecommunications
links, networks, or modems before performing any of the procedures described in this
chapter. Failure to disconnect power, telecommunications links, networks, or modems
before you open the computer or perform any procedures can result in personal injury
or equipment damage. Some circuitry on the board can continue to operate even
though the front panel power button is off.
Follow these guidelines before you begin installing the Desktop Board:
•
•
Always follow the steps in each procedure in the correct order.
Set up a log to record information about your computer, such as model, serial
numbers, installed options, and configuration information.
•
Electrostatic discharge (ESD) can damage components. Perform the procedures
described in this chapter only at an ESD workstation using an antistatic wrist strap
and a conductive foam pad. If such a station is not available, you can provide
some ESD protection by wearing an antistatic wrist strap and attaching it to a
metal part of the computer chassis.
23
Intel Desktop Board D510MO Product Guide
CAUTION
Failure to ensure appropriate airflow may result in reduced performance of both the
processor and/or voltage regulator or, in some instances, damage to the board.
All responsibility for determining the adequacy of any thermal or system design
remains solely with the reader. Intel makes no warranties or representations that
merely following the instructions presented in this document will result in a system
with adequate thermal performance.
CAUTION
Ensure that the ambient temperature does not exceed the board’s maximum operating
temperature. Failure to do so could cause components to exceed their maximum case
temperature and malfunction. For information about the maximum operating
temperature, see the environmental specifications in the Intel Desktop Board Technical
Product Specification.
CAUTION
The board is designed to be passively cooled on a properly ventilated chassis. Chassis
venting locations are recommended over the processor, voltage regulator, and system
memory areas for maximum heat dissipation effectiveness.
Ensure that proper airflow is maintained around the processor, processor voltage
regulator circuit, and the DIMM. Failure to do so may result in damage to these
components.
CAUTION
A thermal rating of 85 oC is required for the DIMMs used on this board.
24
Installing and Replacing Desktop Board Components
Installation Precautions
When you install and test the Intel Desktop Board, observe all warnings and cautions
in the installation instructions.
To avoid injury, be careful of:
•
•
•
•
•
Sharp pins on connectors or headers
Sharp pins on printed circuit assemblies
Rough edges and sharp corners on the chassis
Hot components (such as voltage regulators and heat sinks)
Damage to wires that could cause a short circuit
Observe all warnings and cautions that instruct you to refer computer servicing to
qualified technical personnel.
Prevent Power Supply Overload
Do not overload the power supply output. To avoid overloading the power supply,
make sure that the calculated total current loads of all the modules within the
computer is less than the output current rating of the power supply.
Observe Safety and Regulatory Requirements
Read and adhere to the instructions in this section and the instructions supplied with
the chassis and associated modules. If you do not follow these instructions and the
instructions provided by chassis and module suppliers, you increase safety risk and the
possibility of noncompliance with regional laws and regulations.
Refer to Appendix B for safety and regulatory requirements.
25
Intel Desktop Board D510MO Product Guide
Installing the I/O Shield
The Desktop Board comes with an I/O shield. When installed in the chassis, the shield
blocks radio frequency transmissions, protects internal components from dust and
foreign objects, and promotes correct airflow within the chassis.
Install the I/O shield before installing the Desktop Board in the chassis. Place the
tightly and securely. If the shield does not fit, obtain a properly-sized shield from the
chassis supplier.
Figure 5. Installing the I/O Shield
26
Installing and Replacing Desktop Board Components
Installing and Removing the Desktop Board
CAUTION
Only qualified technical personnel should do this procedure. Disconnect the computer
from its power source before performing the procedures described here. Failure to
disconnect the power before you open the computer can result in personal injury or
equipment damage.
Refer to your chassis manual for instructions on installing and removing the Desktop
Board.
Figure 6 shows the location of the mounting screw holes for Intel Desktop Board
D510MO.
Figure 6. Intel Desktop Board D510MO Mounting Screw Holes
Installing and Removing Memory
NOTE
To be fully compliant with all applicable Intel SDRAM memory specifications, the
boards require DIMMs that support the Serial Presence Detect (SPD) data structure.
The Desktop Board has two 240-pin DDR2 DIMM sockets.
27
Intel Desktop Board D510MO Product Guide
Installing DIMMs
To make sure you have the correct DIMM, place it on the illustration in Figure 7
showing the DDR2 DIMM. All the notches should match the DDR2 DIMM.
Figure 7. Use DDR2 DIMMs
28
Installing and Replacing Desktop Board Components
2. Turn off all peripheral devices connected to the computer. Turn off the computer
and disconnect the AC power cord.
Figure 8. Installing a DIMM
4. Make sure the clips at either end of the DIMM socket are pushed outward to the
open position.
5. Position the DIMM above the socket. Align the small notch at the bottom edge of
the DIMM with the key in the socket (see Figure 8).
6. Insert the bottom edge of the DIMM into the socket.
7. When the DIMM is inserted, push down on the top edge of the DIMM until the
retaining clips snap into place. Make sure the clips are firmly in place.
8. Replace the computer’s cover and reconnect the AC power cord.
29
Intel Desktop Board D510MO Product Guide
Removing DIMMs
To remove a DIMM, follow these steps:
2. Turn off all peripheral devices connected to the computer. Turn off the computer.
3. Remove the AC power cord from the computer.
4. Remove the computer’s cover.
5. Gently spread the retaining clips at each end of the DIMM socket. The DIMM pops
out of the socket.
6. Hold the DIMM by the edges, lift it away from the socket, and store it in an
anti-static package.
7. Reinstall and reconnect any parts you removed or disconnected to reach the DIMM
sockets.
8. Replace the computer’s cover and reconnect the AC power cord.
Connecting SATA Drives
The board has two SATA connectors each supporting one SATA drive. The included
SATA cables support the Serial ATA protocol. For correct cable and drive function:
30
Intel Desktop Board D510MO Product Guide
Installing a Wireless LAN Card in the PCI
Express Full-Mini Card Slot
A wireless LAN card can be installed in the Desktop Board’s PCI Express Full-Mini Card
slot.
steps:
2. Locate the PCI Express Full-Mini Card slot.
A) at a slightly upward angle.
wireless LAN card as shown.
NOTE
External antennas can be connected through the I/O shield by removing any or all of
the cut-outs above the back panel I/O section.
Figure 10. Installing a Wireless LAN Card
32
Installing and Replacing Desktop Board Components
Installing an Intel® Z-U130 USB Solid-State
Drive (or Compatible Device)
An Intel Z-U130 USB Solid-State Drive (or compatible device) can be installed on the
header provides support for the solid state drive.
To install an Intel Z-U130 USB Solid-State Drive (or compatible device) on the Desktop
Board, follow these steps:
USB 2.0 header on the Desktop Board. The connectors are keyed and will mate
correctly when the solid state drive is oriented as shown in Figure 11.
Figure 11. Installing an Intel Z-U130 USB Solid-State Drive
(or Compatible Device)
33
Intel Desktop Board D510MO Product Guide
Connecting to the Internal Headers
Before connecting cables to the internal headers, observe the precautions in "Before
Figure 12. Internal Headers
34
Installing and Replacing Desktop Board Components
Connecting the Front Panel Audio Header
header can be used for both Intel HD Audio and AC ‘97 Audio.
assignments for AC ‘97 Audio.
Table 6. Front Panel Audio Header for Intel HD Audio
Pin
1
Signal Name
Pin
2
Signal Name
[Port 1] Left channel
[Port 1] Right channel
[Port 2] Right channel
SENSE_SEND (Jack detection)
[Port 2] Left channel
Ground
3
4
PRESENCE# (Dongle present)
[Port 1] SENSE_RETURN
Key (no pin)
5
6
7
8
9
10
[Port 2] SENSE_RETURN
Table 7. Front Panel Audio Header for AC ‘97 Audio
Pin
1
Signal Name
MIC
Pin
2
Signal Name
AUD_GND
3
MIC_BIAS
FP_OUT_R
AUD_5V
4
AUD_GND
5
6
FP_RETURN_R
KEY (no pin)
FP_RETURN_L
7
8
9
FP_OUT_L
10
35
Intel Desktop Board D510MO Product Guide
Connecting to the S/PDIF Header
Before connecting to the S/PDIF connector, observe the precautions in "Before You
Table 8 shows the pin assignments for the S/PDIF header.
Table 8. S/PDIF Header
Pin
1
Signal Name
Ground
2
S/PDIF out
VCC (5V)
3
Connecting to the Serial Headers
Before connecting to the serial headers, observe the precautions in "Before You Begin"
Table 9 shows the pin assignments for the serial headers.
Table 9. Serial Port Headers (COM 1 and COM 2)
Pin
Signal Name
Pin
Signal Name
1
3
5
7
9
DCD (Data Carrier Detect)
TXD# (Transmit Data)
Ground
2
RXD# (Receive Data)
DTR (Data Terminal Ready)
DSR (Data Set Ready)
CTS (Clear To Send)
Key (no pin)
4
6
RTS (Request To Send)
RI (Ring Indicator)
8
10
Connecting to the Parallel Port Header
Before connecting to the parallel port header, observe the precautions in "Before You
header.
Table 10 shows the pin assignments for the parallel port header.
Table 10.Parallel Port Header
Pin
1
Standard Signal Name
ECP Signal Name
STROBE#
EPP Signal Name
WRITE#
DATASTB#
PD0
STROBE#
AUTOFD#
PD0
2
AUTOFD#, HOSACK
PD0
3
4
FAULT#
PD1
FAULT#, PERIPHREQST#
PD1
FAULT#
5
PD1
6
INT#
INT#, REVERSERQST#
PD2
RESET#
PD2
7
PD2
8
SLCTIN#
SLCTIN#
ADDRSTB#
36
Installing and Replacing Desktop Board Components
Pin
9
Standard Signal Name
PD3
ECP Signal Name
PD3
EPP Signal Name
PD3
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
GROUND
PD4
GROUND
PD4
GROUND
PD4
GROUND
PD5
GROUND
PD5
GROUND
PD5
GROUND
PD6
GROUND
PD6
GROUND
PD6
GROUND
PD7
GROUND
PD7
GROUND
PD7
GROUND
ACK#
GROUND
ACK#
GROUND
INTR
GROUND
BUSY
GROUND
BUSY#, PERIPHACK
GROUND
PE, ACKREVERSE#
GROUND
SELECT
GROUND
WAIT#
GROUND
PERROR
GROUND
SELECT
GROUND
PE
GROUND
SELECT
KEY (no pin)
KEY (no pin)
KEY (no pin)
Connecting to the Front Panel Wireless Activity LED
Header
Before connecting to the front panel wireless activity LED header, observe the
location of the front panel wireless activity LED header.
Table 11 shows the pin assignments for the front panel wireless activity LED header.
Table 11.Front Panel Wireless Activity LED Header
Pin
1
Signal Name
LED (+)
2
Ground
37
Intel Desktop Board D510MO Product Guide
Connecting to the Front Panel Header
Before connecting to the front panel header, observe the precautions in "Before You
header.
Table 12 shows the pin assignments for the front panel header.
Table 12.Front Panel Header Signal Names
Pin Signal
In/Out Description
Pin Signal
In/Out
Description
Hard Drive Activity LED
Power LED
Hard disk LED pull-
up (330 Ω) to +5 V
Front panel
green LED
1
3
HD_PWR
HDA#
Out
Out
2
4
HDR_BLNK_GRN Out
Hard disk active
LED
Front panel
yellow LED
HDR_BLNK_YEL
Out
Reset Switch
On/Off Switch
5
7
Ground
Ground
6
8
SWITCH_ON#
Ground
In
Power switch
Ground
FP_RESET# In
+5 V
Reset switch
Power
Not Connected
9
Power
10 N/C
No pin
Connecting to the Front Panel USB 2.0 Headers
Before connecting to the USB 2.0 headers, observe the precautions in "Before You
to support a Flash Memory Drive such as the Intel Z-U130 USB Solid-State Drive (or
Table 13.Front Panel USB Header
Pin
1
Signal Name
+5 VDC
D-
Pin
2
Signal Name
+5 VDC
D-
3
4
5
6
D+
D+
7
8
Ground
Ground
No Connect
9
10
KEY (no pin)
38
Installing and Replacing Desktop Board Components
Table 14. Front Panel USB Header with Intel Z-U130 USB Solid-State Drive
(or Compatible Device) Support
Pin
1
Signal Name
+5 VDC
D-
Pin
2
Signal Name
No Connect
No Connect
No Connect
No Connect
LED#
3
4
5
6
D+
7
8
Ground
9
10
KEY (no pin)
Connecting a Chassis Fan
to this header.
Figure 13. Location of the Chassis Fan Header
39
Intel Desktop Board D510MO Product Guide
Connecting the Power Supply Cable
CAUTION
Failure to use an appropriate power supply to the Desktop Board may result in damage
to the board or the system may not function properly.
Figure 14 shows the location of the power connector.
Figure 14. Connecting a Power Supply Cable
40
Installing and Replacing Desktop Board Components
Setting the BIOS Configuration Jumper
NOTE
Always turn off the power and unplug the power cord from the computer before
changing a jumper. Moving the jumper with the power on may result in unreliable
computer operation.
Figure 15 shows the location of the Desktop Board’s BIOS configuration jumper block.
Figure 15. BIOS Configuration Jumper Block
jumper settings for each of the available modes.
41
Intel Desktop Board D510MO Product Guide
Figure 15 shows the location of the Desktop Board’s BIOS configuration jumper block.
Table 15.Jumper Settings for the BIOS Setup Program Modes
Jumper
Setting
Mode
Description
Normal (default) (1-2)
The BIOS uses the current configuration and
passwords for booting.
Configure (2-3)
Recovery (None)
After the Power-On Self-Test (POST) runs, the
BIOS displays the Maintenance Menu. Use this
menu to clear passwords.
The BIOS recovers data from a recovery diskette
in the event of a failed BIOS update.
Clearing Passwords
This procedure assumes that the board is installed in the computer and the
configuration jumper is set to normal mode.
2. Turn off all peripheral devices connected to the computer. Turn off the computer.
Disconnect the computer’s power cord from the AC power source (wall outlet or
power adapter).
3. Remove the computer cover.
5. Place the jumper on pins 2-3 as shown below.
6. Replace the cover, plug in the computer, turn on the computer, and allow it to
boot.
7. The computer starts the Setup program. Setup displays the Maintenance menu.
8. Use the arrow keys to select Clear Passwords. Press <Enter> and Setup displays a
pop-up screen requesting that you confirm clearing the password. Select Yes and
press <Enter>. Setup displays the maintenance menu again.
9. Press <F10> to save the current values and exit Setup.
42
Installing and Replacing Desktop Board Components
10.Turn off the computer. Disconnect the computer’s power cord from the AC power
source.
11.Remove the computer cover.
12.To restore normal operation, place the jumper on pins 1-2 as shown below.
13.Replace the cover, plug in the computer, and turn on the computer.
Replacing the Battery
A coin-cell battery powers the Desktop Board’s real-time clock and CMOS memory.
When the computer is not plugged into a wall socket, the battery has an estimated life
of three years. When the computer is plugged in, the standby current from the power
supply extends the life of the battery. The clock is accurate to ± 13 minutes/year at
25 ºC with 3.3 VSB applied.
When the voltage drops below a certain level, the BIOS Setup program settings stored
in CMOS RAM (for example, the date and time) might not be accurate. Replace the
battery.
CAUTION
Risk of explosion if the battery is replaced with an incorrect type. Batteries should be recycled where
possible. Disposal of used batteries must be in accordance with local environmental regulations.
PRÉCAUTION
Risque d'explosion si la pile usagée est remplacée par une pile de type incorrect. Les piles usagées doivent
être recyclées dans la mesure du possible. La mise au rebut des piles usagées doit respecter les
réglementations locales en vigueur en matière de protection de l'environnement.
FORHOLDSREGEL
Eksplosionsfare, hvis batteriet erstattes med et batteri af en forkert type. Batterier bør om muligt genbruges.
Bortskaffelse af brugte batterier bør foregå i overensstemmelse med gældende miljølovgivning.
OBS!
Det kan oppstå eksplosjonsfare hvis batteriet skiftes ut med feil type. Brukte batterier bør kastes i henhold til
gjeldende miljølovgivning.
VIKTIGT!
Risk för explosion om batteriet ersätts med felaktig batterityp. Batterier ska kasseras enligt de lokala
miljövårdsbestämmelserna.
43
Intel Desktop Board D510MO Product Guide
VARO
Räjähdysvaara, jos pariston tyyppi on väärä. Paristot on kierrätettävä, jos se on mahdollista. Käytetyt
paristot on hävitettävä paikallisten ympäristömääräysten mukaisesti.
VORSICHT
Bei falschem Einsetzen einer neuen Batterie besteht Explosionsgefahr. Die Batterie darf nur durch denselben
oder einen entsprechenden, vom Hersteller empfohlenen Batterietyp ersetzt werden. Entsorgen Sie ver-
brauchte Batterien den Anweisungen des Herstellers entsprechend.
AVVERTIMENTO
Esiste il pericolo di un esplosione se la pila non viene sostituita in modo corretto. Utilizzare solo pile uguali
o di tipo equivalente a quelle consigliate dal produttore. Per disfarsi delle pile usate, seguire le istruzioni del
produttore.
PRECAUCIÓN
Existe peligro de explosión si la pila no se cambia de forma adecuada. Utilice solamente pilas iguales o del
mismo tipo que las recomendadas por el fabricante del equipo. Para deshacerse de las pilas usadas, siga
igualmente las instrucciones del fabricante.
WAARSCHUWING
Er bestaat ontploffingsgevaar als de batterij wordt vervangen door een onjuist type batterij. Batterijen
moeten zoveel mogelijk worden gerecycled. Houd u bij het weggooien van gebruikte batterijen aan de
plaatselijke milieuwetgeving.
ATENÇÃO
Haverá risco de explosão se a bateria for substituída por um tipo de bateria incorreto. As baterias devem ser
recicladas nos locais apropriados. A eliminação de baterias usadas deve ser feita de acordo com as
regulamentações ambientais da região.
AŚCIAROŽZNAŚĆ
Існуе рызыка выбуху, калі заменены акумулятар неправільнага тыпу. Акумулятары павінны, па
магчымасці, перепрацоўвацца. Пазбаўляцца ад старых акумулятараў патрэбна згодна з мясцовым
заканадаўствам па экалогіі.
UPOZORNÌNÍ
V případě výměny baterie za nesprávný druh může dojít k výbuchu. Je-li to možné, baterie by měly být
recyklovány. Baterie je třeba zlikvidovat v souladu s místními předpisy o životním prostředí.
Προσοχή
Υπάρχει κίνδυνος για έκρηξη σε περίπτωση που η μπαταρία αντικατασταθεί από μία λανθασμένου τύπου. Οι
μπαταρίες θα πρέπει να ανακυκλώνονται όταν κάτι τέτοιο είναι δυνατό. Η απόρριψη των χρησιμοποιημένων
μπαταριών πρέπει να γίνεται σύμφωνα με τους κατά τόπο περιβαλλοντικούς κανονισμούς.
44
Installing and Replacing Desktop Board Components
VIGYÁZAT
Ha a telepet nem a megfelelő típusú telepre cseréli, az felrobbanhat. A telepeket lehetőség szerint újra kell
hasznosítani. A használt telepeket a helyi környezetvédelmi előírásoknak megfelelően kell kiselejtezni.
AWAS
Risiko letupan wujud jika bateri digantikan dengan jenis yang tidak betul. Bateri sepatutnya dikitar semula
jika boleh. Pelupusan bateri terpakai mestilah mematuhi peraturan alam sekitar tempatan.
OSTRZEŻENIE
Istnieje niebezpieczeństwo wybuchu w przypadku zastosowania niewłaściwego typu baterii. Zużyte baterie
należy w miarę możliwości utylizować zgodnie z odpowiednimi przepisami ochrony środowiska.
PRECAUŢIE
Risc de explozie, dacă bateria este înlocuită cu un tip de baterie necorespunzător. Bateriile trebuie reciclate,
dacă este posibil. Depozitarea bateriilor uzate trebuie să respecte reglementările locale privind protecţia
mediului.
ВНИМАНИЕ
При использовании батареи несоответствующего типа существует риск ее взрыва. Батареи
должны быть утилизированы по возможности. Утилизация батарей должна проводится по
правилам, соответствующим местным требованиям.
UPOZORNENIE
Ak batériu vymeníte za nesprávny typ, hrozí nebezpečenstvo jej výbuchu.
Batérie by sa mali podľa možnosti vždy recyklovať. Likvidácia použitých batérií sa musí vykonávať v súlade
s miestnymi predpismi na ochranu životného prostredia.
POZOR
Zamenjava baterije z baterijo drugačnega tipa lahko povzroči eksplozijo.
Če je mogoče, baterije reciklirajte. Rabljene baterije zavrzite v skladu z lokalnimi okoljevarstvenimi predpisi.
.
UYARI
Yanlış türde pil takıldığında patlama riski vardır. Piller mümkün olduğunda geri dönüştürülmelidir.
Kullanılmış piller, yerel çevre yasalarına uygun olarak atılmalıdır.
45
Intel Desktop Board D510MO Product Guide
OСТОРОГА
Використовуйте батареї правильного типу, інакше існуватиме ризик вибуху.
Якщо можливо, використані батареї слід утилізувати. Утилізація використаних батарей має бути
виконана згідно місцевих норм, що регулюють охорону довкілля.
46
Installing and Replacing Desktop Board Components
2. Turn off all peripheral devices connected to the computer. Disconnect the
computer’s power cord from the AC power source (wall outlet or power adapter).
3. Remove the computer cover.
5. Push the battery retention clip aside and remove the battery from the connector as
6. Install the new battery in the connector, making sure to orient the “+” and “-”
correctly.
7. Replace the computer cover.
Figure 16. Removing the Battery
47
Intel Desktop Board D510MO Product Guide
48
3 Updating the BIOS
The BIOS Setup program can be used to view and change the BIOS settings for the
computer. You can access the BIOS Setup program by pressing the <F2> key after
the Power-On Self-Test (POST) memory test begins and before the operating system
boot begins.
This chapter tells you how to update the BIOS by either using the Intel Express BIOS
Update utility or the Iflash Memory Update utility, and how to recover the BIOS if an
update fails.
Updating the BIOS with the Intel® Express
BIOS Update Utility
With the Intel Express BIOS Update utility you can update the system BIOS while in
the Windows environment. The BIOS file is included in an automated update utility
that combines the functionality of the Intel® Flash Memory Update Utility and the ease
of use of Windows-based installation wizards.
To update the BIOS with the Intel Express BIOS Update utility:
2. Navigate to the Intel Desktop Board D510MO page, click “[view] Latest BIOS
updates,” and select the Express BIOS Update utility file.
3. Download the file to your hard drive. (You can also save this file to a removable
USB device. This is useful if you are updating the BIOS for multiple identical
systems.)
4. Close all other applications. This step is required. Your system will be rebooted at
the last Express BIOS Update window.
5. Double-click the executable file from the location on your hard drive where it was
saved. This runs the update program.
6. Follow the instructions provided in the dialog boxes to complete the BIOS update.
49
Intel Desktop Board D510MO Product Guide
Updating the BIOS with the Iflash Memory
Update Utility
You can use the information in this section to update the BIOS using the Iflash
Memory Update Utility.
Obtaining the BIOS Update File
You can update to a new version of the BIOS by using the Iflash BIOS update file.
The Iflash BIOS update file is a compressed file that contains the files you need to
update the BIOS. The Iflash BIOS update file contains:
•
•
New BIOS file
Intel Flash Memory Update Utility
You can obtain either of these files through your computer supplier or by navigating to
the Intel Desktop Board D510MO page at
Navigate to the Intel Desktop D510MO page, click “[view] Latest BIOS updates,” and
select the Iflash BIOS Update utility file.
CAUTION
Do not interrupt the process or the system may not function properly.
Using the Iflash Memory Update Utility
With the Iflash Memory update utility you can update the system BIOS from a
bootable USB flash drive or other bootable USB media. The Iflash BIOS update files
can be extracted locally to your hard drive and copied to a bootable USB flash drive or
other bootable USB media.
NOTE
Review the instructions distributed with the update utility before attempting a BIOS
update.
CAUTION
Do not interrupt the process or the system may not function properly.
1. Uncompress the BIOS update file and copy the .BIO file and IFLASH.EXE to a
bootable USB flash drive or other bootable USB media.
2. Configure the BIOS or use the F10 key option during POST to boot to the USB
device.
3. Manually run the IFLASH.EXE file from the USB device and manually update the
BIOS.
50
Updating the BIOS
Recovering the BIOS
It is unlikely that anything will interrupt a BIOS update; however, if an interruption
can and cannot be used for BIOS recovery. The BIOS recovery media does not have
to be bootable.
Table 16.Acceptable Drives/Media Types for BIOS Recovery
Media Type
Can be Used for BIOS Recovery?
CD-ROM drive connected to the SATA interface
USB removable drive (a USB Flash Drive, for example)
USB diskette drive (with a 1.44 MB diskette)
USB hard disk drive
Yes
Yes
No
No
NOTE
For more information about BIOS update and recovery, go to
51
Intel Desktop Board D510MO Product Guide
52
A Board Status and Error Messages
This appendix describes status and error messages generated by the Desktop Board’s
BIOS. The BIOS indicates these error messages with front-panel Power LED blink
codes, speaker beep codes, and by displaying text on the video monitor.
BIOS Beep Codes
The BIOS uses audible beep codes to signal status messages and error messages
indicating recoverable errors that occur during the POST. The beep codes are listed in
Table 17.BIOS Beep Codes
Type
Pattern
Frequency
F2 Setup/F10 Boot
Menu Prompt
One 0.5-second beep when the BIOS is
ready to accept keyboard input
932 Hz
Video error
On-off (1.0 second each) two times, then a 932 Hz
2.5-second pause (off); the entire pattern
repeats (beeps and pause) once and the
BIOS will continue to boot.
When no VGA option ROM
is found.
Memory error
On-off (1.0 second each) three times, then 932 Hz
a 2.5-second pause (off); the entire pattern
repeats (beeps and pause) until the system
is powered off.
Thermal trip warning Alternate high and low beeps (1.0 second
each) for eight beeps, followed by system
shut down.
High beep 2000 Hz
Low beep 1500 Hz
53
Intel Desktop Board D510MO Product Guide
BIOS Front-panel Power LED Blink Codes
The BIOS also blinks the front-panel power LED to signal status messages and error
messages indicating certain recoverable errors that occur during the POST. The blink
codes are listed in Table 18.
Table 18.BIOS Front-panel Power LED Blink Codes
Type
Pattern
Note
BIOS update in
progress
Off when the update begins, then on for
0.5 second, and then off for 0.5 second.
The pattern repeats until the BIOS update
is complete.
Video error
On-off (1.0 second each) two times, then a When no VGA option ROM
2.5-second pause (off); the entire pattern
repeats (blinks and pause) until the system
is powered off.
is found.
Memory error
On-off (1.0 second each) three times, then
a 2.5-second pause (off); the entire pattern
repeats (blinks and pause) until the system
is powered off.
Thermal trip warning Each beep will be accompanied by the
following blink pattern: 0.25 second on,
0.25 second off, 0.25 second on,
0.25 second off. This results in a total of
16 blinks followed by system shut down.
POST Error Messages
The BIOS also displays error messages on the video monitor when certain recoverable
description of each.
Table 19.POST Error Messages
Error Message
Explanation
CMOS Battery Low
CMOS Checksum Bad
The battery may be losing power.
The CMOS checksum is incorrect. The CMOS memory
may have been corrupted. Run Setup to reset values.
Memory Size Decreased
No Boot Device Available
Memory size has decreased since the last boot. If no
memory was removed, then memory may be bad.
System did not find a device to boot.
54
B Regulatory Compliance
This appendix contains the following regulatory compliance information for Intel
Desktop Board D510MO:
•
•
•
•
•
Safety standards
European Union Declaration of Conformity statement
Product Ecology statements
Electromagnetic Compatibility (EMC) regulations
Product certifications
Safety Standards
Intel Desktop Board D510MO complies with the safety standards stated in Table 20
when correctly installed in a compatible host system.
Table 20.Safety Standards
Regulation
Title
CSA/UL 60950-1, First
Edition
Information Technology Equipment – Safety - Part 1: General
Requirements (USA and Canada)
EN 60950-1:2006, Second
Edition
Information Technology Equipment – Safety - Part 1: General
Requirements (European Union)
IEC 60950-1:2005, Second
Edition
Information Technology Equipment – Safety - Part 1: General
Requirements (International)
Place Battery Marking
There is insufficient space on this Desktop Board to provide instructions for replacing
and disposing of the Lithium ion coin cell battery. For system safety certification, the
statement below or an equivalent statement is required to be permanently and legibly
marked on the chassis near the battery.
CAUTION
Risk of explosion if the battery is replaced with an incorrect type. Batteries should be
recycled where possible. Disposal of used batteries must be in accordance with local
environmental regulations.
A suitable caution label is included with Intel Desktop Board D510MO.
For information about replacing the battery, go to page 43.
55
Intel Desktop Board D510MO Product Guide
European Union Declaration of Conformity
Statement
We, Intel Corporation, declare under our sole responsibility that the product Intel®
Desktop Board D510MO is in conformity with all applicable essential requirements
necessary for CE marking, following the provisions of the European Council Directives
2004/108/EC (EMC Directive) and 2006/95/EC (Low Voltage Directive).
The product is properly CE marked demonstrating this conformity and is for
distribution within all member states of the EU with no restrictions.
This product follows the provisions of the European Directives 2004/108/EC and
2006/95/EC.
Čeština Tento výrobek odpovídá požadavkům evropských směrnic 2004/108/EC a
2006/95/EC.
Dansk Dette produkt er i overensstemmelse med det europæiske direktiv
2004/108/EC & 2006/95/EC.
Dutch Dit product is in navolging van de bepalingen van Europees Directief
2004/108/EC & 2006/95/EC.
Eesti Antud toode vastab Euroopa direktiivides 2004/108/EC ja 2006/95/EC
kehtestatud nõuetele.
Suomi Tämä tuote noudattaa EU-direktiivin 2004/108/EC & 2006/95/EC määräyksiä.
Français Ce produit est conforme aux exigences de la Directive Européenne
2004/108/EC & 2006/95/EC.
Deutsch Dieses Produkt entspricht den Bestimmungen der Europäischen Richtlinie
2004/108/EC & 2006/95/EC.
Ελληνικά Το παρόν προϊόν ακολουθεί τις διατάξεις των Ευρωπαϊκών Οδηγιών
2004/108/EC και 2006/95/EC.
Magyar E termék megfelel a 2004/108/EC és 2006/95/EC Európai Irányelv
előírásainak.
Icelandic Þessi vara stenst reglugerð Evrópska Efnahags Bandalagsins númer
2004/108/EC & 2006/95/EC.
Italiano Questo prodotto è conforme alla Direttiva Europea 2004/108/EC &
2006/95/EC.
Latviešu Šis produkts atbilst Eiropas Direktīvu 2004/108/EC un 2006/95/EC
noteikumiem.
Lietuvių Šis produktas atitinka Europos direktyvų 2004/108/EC ir 2006/95/EC
nuostatas.
Malti Dan il-prodott hu konformi mal-provvedimenti tad-Direttivi Ewropej
2004/108/EC u 2006/95/EC.
56
Regulatory Compliance
Norsk Dette produktet er i henhold til bestemmelsene i det europeiske direktivet
2004/108/EC & 2006/95/EC.
Polski Niniejszy produkt jest zgodny z postanowieniami Dyrektyw Unii Europejskiej
2004/108/EC i 2006/95/EC.
Portuguese Este produto cumpre com as normas da Diretiva Européia 2004/108/EC
& 2006/95/EC.
Español Este producto cumple con las normas del Directivo Europeo 2004/108/EC &
2006/95/EC.
Slovensky Tento produkt je v súlade s ustanoveniami európskych direktív
2004/108/EC a 2006/95/EC.
Slovenščina Izdelek je skladen z določbami evropskih direktiv 2004/108/EC in
2006/95/EC.
Svenska Denna produkt har tillverkats i enlighet med EG-direktiv 2004/108/EC &
2006/95/EC.
Türkçe Bu ürün, Avrupa Birliği’nin 2004/108/EC ve 2006/95/EC yönergelerine uyar.
Product Ecology Statements
The following information is provided to address worldwide product ecology concerns
and regulations.
Recycling Considerations
As part of its commitment to environmental responsibility, Intel has implemented the
Intel® Product Recycling Program to allow retail consumers of Intel’s branded products
to return used products to selected locations for proper recycling.
Please consult http://www.intel.com/intel/other/ehs/product_ecology
for the details of this program, including the scope of covered products, available
locations, shipping instructions, terms and conditions, etc.
中文
作为其对环境责任之承诺的部分，英特尔已实施 Intel Product Recycling Program
（英特尔产品回收计划），以允许英特尔品牌产品的零售消费者将使用过的产品退还至指定地点作恰
当的重复使用处理。
了解此计划的详情，包括涉及产品之范围、回收地点、运送指导、条款和条件等。
57
Intel Desktop Board D510MO Product Guide
Deutsch
Als Teil von Intels Engagement für den Umweltschutz hat das Unternehmen das Intel
Produkt-Recyclingprogramm implementiert, das Einzelhandelskunden von Intel
Markenprodukten ermöglicht, gebrauchte Produkte an ausgewählte Standorte für
ordnungsgemäßes Recycling zurückzugeben.
Details zu diesem Programm, einschließlich der darin eingeschlossenen Produkte,
verfügbaren Standorte, Versandanweisungen, Bedingungen usw., finden Sie auf der
Español
Como parte de su compromiso de responsabilidad medioambiental, Intel ha
implantado el programa de reciclaje de productos Intel, que permite que los
consumidores al detalle de los productos Intel devuelvan los productos usados en los
lugares seleccionados para su correspondiente reciclado.
para ver los detalles del programa, que incluye los productos que abarca, los lugares
disponibles, instrucciones de envío, términos y condiciones, etc.
Français
Dans le cadre de son engagement pour la protection de l'environnement, Intel a mis
en œuvre le programme Intel Product Recycling Program (Programme de recyclage
des produits Intel) pour permettre aux consommateurs de produits Intel de recycler
les produits usés en les retournant à des adresses spécifiées.
savoir plus sur ce programme, à savoir les produits concernés, les adresses
disponibles, les instructions d'expédition, les conditions générales, etc.
日本語
インテルでは、環境保護活動の一環として、使い終えたインテル
ブランド製品を指定の場所へ返送していただき、リサイクルを適切に行えるよう、インテル製品リサイクル
プログラムを発足させました。
対象製品、返送先、返送方法、ご利用規約など、このプログラムの詳細情報は、http://www.intel.com/in
tel/other/ehs/product_ecology （英語）をご覧ください。
Malay
Sebagai sebahagian daripada komitmennya terhadap tanggungjawab persekitaran,
Intel telah melaksanakan Program Kitar Semula Produk untuk membenarkan
pengguna-pengguna runcit produk jenama Intel memulangkan produk terguna ke
lokasi-lokasi terpilih untuk dikitarkan semula dengan betul.
butir-butir program ini, termasuklah skop produk yang dirangkumi, lokasi-lokasi
tersedia, arahan penghantaran, terma & syarat, dsb.
58
Regulatory Compliance
Portuguese
Como parte deste compromisso com o respeito ao ambiente, a Intel implementou o
Programa de Reciclagem de Produtos para que os consumidores finais possam enviar
produtos Intel usados para locais selecionados, onde esses produtos são reciclados de
maneira adequada.
obter os detalhes sobre este programa, inclusive o escopo dos produtos cobertos, os
locais disponíveis, as instruções de envio, os termos e condições, etc.
Russian
В качестве части своих обязательств к окружающей среде, в Intel создана
программа утилизации продукции Intel (Product Recycling Program) для
предоставления конечным пользователям марок продукции Intel возможности
возврата используемой продукции в специализированные пункты для должной
утилизации.
Пожалуйста, обратитесь на веб-сайт
http://www.intel.com/intel/other/ehs/product_ecology за информацией об этой
программе, принимаемых продуктах, местах приема, инструкциях об отправке,
положениях и условиях и т.д.
Türkçe
Intel, çevre sorumluluğuna bağımlılığının bir parçası olarak, perakende tüketicilerin
Intel markalı kullanılmış ürünlerini belirlenmiş merkezlere iade edip uygun şekilde geri
dönüştürmesini amaçlayan Intel Ürünleri Geri Dönüşüm Programı’nı uygulamaya
koymuştur.
Bu programın ürün kapsamı, ürün iade merkezleri, nakliye talimatları, kayıtlar ve
şartlar v.s dahil bütün ayrıntılarını ögrenmek için lütfen
59
Intel Desktop Board D510MO Product Guide
Lead-free 2LI/Pb-free 2LI Board
The electronics industry is transitioning to European Union (EU) Restriction of
Hazardous Substances (RoHS)-compliant products. The RoHS legislation restricts the
use of six materials. One of these restricted materials is lead. Lead is the most
common and problematic of the RoHS restricted materials.
There are exemptions in RoHS that allow the use of lead in some very limited locations
in electronic products. Maximum lead concentration values have been established for
RoHS-compliant electronic products that allow up to 1000 ppm of lead.
Lead-free/Pb-free is a nickname that is often used (or misused) for RoHS-compliant
products. In this case, the term "Lead-free/Pb-free" means that lead has been
removed where required by the RoHS legislation but still may exist as an impurity
below 1000 ppm.
The term "Lead-free 2LI/Pb-free 2LI" means lead-free second level interconnect (2LI).
The balls, leads, or pads used to connect the component to a printed circuit board are
lead-free, but the first level interconnect (FLI) is not lead-free. The use of lead in the
FLI is acceptable because of the RoHS "flip chip" or "die bump" interconnect
exemption.
Intel Desktop Board D510MO is a lead-free second level interconnect product.
Table 21 shows the lead-free second level interconnect marks as they appear on the
board and accompanying collateral. These marks are based on JEDEC standard
J-STD-609, “Marking and Labeling of Components, PCBs and PCBAs to Identify Lead,
Lead Free and Other Attributes.”
For more information concerning Intel’s lead-free initiatives, refer to
Table 21.Lead-Free Second Level Interconnect Marks
Description
Mark
This symbol is used to identify
electrical and electronic
assemblies and components in
which the Pb concentration
level in the Desktop Board
substrate and the solder
connections from the board to
the components (second-level
interconnect) is not greater
than 0.1% by weight
or
or
(1000 ppm).
60
Regulatory Compliance
Restriction of Hazardous Substances (RoHS)
European Union RoHS
EU RoHS Directive 2002/95/EC restricts the use of the following six materials in
various types of electronic and electrical equipment:
•
•
•
•
•
•
Lead
Mercury
Cadmium
Hexavalent chromium
Polybrominated biphenyls (PBB)
Polybrominated diphenyl ether (PBDE)
The maximum concentrations allowed are 0.1% or 1000 ppm (except for cadmium,
which is limited to 0.01% or 100 ppm) by weight of homogeneous material.
Intel Desktop Board D510MO complies with these restrictions.
China RoHS
“China RoHS” is the term used by industry generally to describe legislation
implemented by the Ministry of Information Industry (MII) in the People's Republic of
China for the control of pollution by electronic information products (EIP). The official
title of the China RoHS regulation is “Management Methods for Controlling Pollution by
Electronic Information Products.”
China RoHS bans the same substances and has the same limits as EU RoHS.
However, the China RoHS regulation requires specific product marking and a self-
declaration of the controlled substances contained in each product.
Intel Desktop Board D510MO is a China RoHS-compliant product.
The required China RoHS mark indicates the product’s Environmental Friendly Usage
Period (EFUP). The EFUP is defined as the number of years for which listed controlled
substances will not leak or chemically deteriorate while in the product. The EFUP for
Intel Desktop Boards has been determined to be 10 years.
The EFUP for Intel Desktop Board D510MO is shown in Table 22.
Table 22.China RoHS Environmentally Friendly Use Period Mark
Description
Mark
This is an example of the
symbol used on Intel Desktop
Boards and associated
collateral. The color of the
mark may vary depending
upon the application. The
Environmental Friendly Usage
Period (EFUP) for Intel
Desktop Boards has been
determined to be 10 years.
61
Intel Desktop Board D510MO Product Guide
The China MII also stipulates that a material Self Declaration Table (SDT) must be
included in a product’s user documentation. The SDT for Intel Desktop Board D510MO
is shown in Figure 17.
Figure 17. Intel Desktop Board D510MO China RoHS Material
Self Declaration Table
62
Regulatory Compliance
EMC Regulations
Intel Desktop Board D510MO complies with the EMC regulations stated in Table 23
when correctly installed in a compatible host system.
Table 23.EMC Regulations
Regulation (Class B)
Title
FCC 47 CFR Part 15,
Subpart B
Title 47 of the Code of Federal Regulations, Part 15, Subpart B,
Radio Frequency Devices. (USA)
ICES-003 Issue 4
Interference-Causing Equipment Standard, Digital Apparatus.
(Canada)
EN55022:2006
Limits and methods of measurement of Radio Interference
Characteristics of Information Technology Equipment. (European
Union)
EN55024:1998
EN55022:2006
Information Technology Equipment – Immunity Characteristics
Limits and methods of measurement. (European Union)
Australian Communications Authority, Standard for
Electromagnetic Compatibility. (Australia and New Zealand)
CISPR 22:2005
+A1:2005 +A2:2006
Limits and methods of measurement of Radio Disturbance
Characteristics of Information Technology Equipment.
(International)
CISPR 24:1997
+A1:2001 +A2:2002
Information Technology Equipment – Immunity Characteristics –
Limits and Methods of Measurement. (International)
VCCI V-3/2007.04,
V-4/2007.04
Voluntary Control for Interference by Information Technology
Equipment (Japan)
KN-22, KN-24
Korean Communications Commission – Framework Act on
Telecommunications and Radio Waves Act. (South Korea).
CNS 13438:2006
Bureau of Standards, Metrology and Inspection. (Taiwan)
Japanese Kanji statement translation: This is a Class B product based on the standard
of the Voluntary Control Council for Interference from Information Technology
Equipment (VCCI). If this is used near a radio or television receiver in a domestic
environment, it may cause radio interference. Install and use the equipment
according to the instruction manual.
63
Intel Desktop Board D510MO Product Guide
Korean Class B statement translation: This is household equipment that is certified to
comply with EMC requirements. You may use this equipment in residential
environments and other non-residential environments.
Ensure Electromagnetic Compatibility (EMC)
Compliance
Before computer integration, make sure that the power supply and other modules or
peripherals, as applicable, have passed Class B EMC testing and are marked
accordingly.
Pay close attention to the following when reading the installation instructions for the
host chassis, power supply, and other modules:
•
•
•
•
Product certifications or lack of certifications
External I/O cable shielding and filtering
Mounting, grounding, and bonding requirements
Keying connectors when mating the wrong connectors could be hazardous
If the power supply and other modules or peripherals, as applicable, are not Class B
EMC compliant before integration, then EMC testing may be required on a
representative sample of the newly completed computer.
64
Regulatory Compliance
Product Certifications
Board-Level Certification Markings
Intel Desktop Board D510MO has the product certification markings shown in
Table 24.Product Certification Markings
Description
Mark
UL joint US/Canada Recognized Component mark. Includes adjacent
UL file number for Intel Desktop Boards: E210882.
FCC Declaration of Conformity logo mark for Class B equipment.
Includes Intel name and D510MO model designation.
CE mark. Declaring compliance to European Union (EU) EMC
directive and Low Voltage directive.
Australian Communications Authority (ACA) and New Zealand Radio
Spectrum Management (NZ RSM) C-tick mark. Includes adjacent
Intel supplier code number, N-232.
Japan VCCI (Voluntary Control Council for Interference) mark.
S. Korea KCC (Korean Communications Commission) mark. Includes
adjacent KCC certification number: CPU-D510MO (B).
Taiwan BSMI (Bureau of Standards, Metrology and Inspections)
mark. Includes adjacent Intel company number, D33025.
Printed wiring board manufacturer’s recognition mark. Consists of a
unique UL recognized manufacturer’s logo, along with a flammability
rating (solder side).
V-0
65
Intel Desktop Board D510MO Product Guide
Chassis and Component Certifications
Ensure that the chassis and certain components; such as the power supply, peripheral
drives, wiring, and cables; are components certified for the country or market where
used. Agency certification marks on the product are proof of certification. Typical
product certifications include:
In Europe
The CE marking signifies compliance with all applicable European requirements. If the
chassis and other components are not properly CE marked, a supplier’s Declaration of
Conformity statement to the European EMC directive and Low Voltage directive (as
applicable), should be obtained. Additionally, other directives, such as the Radio and
Telecommunications Terminal Equipment (R&TTE) directive may also apply depending
on product features.
In the United States
A certification mark by a Nationally Recognized Testing Laboratory (NRTL) such as UL,
CSA, or ETL signifies compliance with safety requirements. Wiring and cables must
also be UL listed or recognized and suitable for the intended use. The FCC Class B
logo for home or office use signifies compliance with electromagnetic interference
(EMI) requirements.
In Canada
A nationally recognized certification mark such as CSA or cUL signifies compliance with
safety requirements. The Industry Canada statement at the front of this product guide
demonstrates compliance with Canadian EMC regulations.
66
|
JVC AV 28BT8EPS User Manual
JVC Digital Signage Display 24" LCD DTR24L41DU User Manual
Kenmore 790 3249 User Manual
KitchenAid KECC507B User Manual
LG Electronics LG Life Good Computer Monitor L1953TR User Manual
NEC MultiSync EA261WM BK User Manual
Panasonic CT 20SX11 User Manual
Philips 14PV200 User Manual
Philips 32RF52S User Manual
Philips PSC 605 User Manual