E-1
PACKING CONTENTS
INTRODUCTION
The package contains:
This microprocessor-based, digital control 15-in.
color monitor is a high-performance, easy-to-use
product. This monitor uses a mini-neck CRT to
reduce power consumption during normal operation.
It also employs the latest on-screen-menu technology.
The microprocessor capability offers 13 most
commonly used factory-preset VESA timing modes,
and eight modes for the user to adjust to the special
timings that user might prefer.
•
•
•
CRT monitor (M/T 6331)
ac power cord
User manual
UNPACKING
PROCEDURE
1
2
This manual provides operating, usage, and safety
information for your monitor.
POWER SAVING
The monitor is driven to different power saving states
when it receives control signals from the display
controller. This process meets the Environmental
Protection Agency (EPA) Energy Star requirements
and reduces power consumption.
4
3
The monitor works in the following four states
according to the VESA-standard Display Power
Management Signal:
Power
Consumption
LED
Color
State
5
ON
Normal
<15W
<15W
< 5W
Green
Yellow
Yellow
Amber
STANDBY
SUSPEND
OFF
The power saving states are sustained until a control
signal has been detected or the keyboard or mouse is
activated. The recovery time from STANDBY/
SUSPEND state to ON state occurs within three
seconds. It usually takes less than 15 seconds from
OFF state back to ON state.
REPACKING
Save the origional box and all packing material for
future shipping needs.
*
Packing materials and product are recyclable.
113393-0A-E.pm6
1
8/1/00, 6:38 PM
E-3
USER CONTROLS AND INDICATORS
a
b
c
2
1
a. Displays menu & exits menu
1. Power LED
b. Scrolls through menu to choose an icon
for adjustment /
2. Power ON/OFF switch
Adjusts level of selected icon
c. Confirms menu selection
113393-0A-E.pm6
3
8/1/00, 6:38 PM
E-4
USING THE ON-SCREEN MENU
1
1) Menu screen-press the
button to display the menu below and exit menus
Select mark
Press the
button to move the selection
mark to the desired location.
Adjustment icons
2
When the button is pressed.
1 : CONTRAST : 2
The selected adjustment screen appears.
The item presently
being adjusted is
shown.
CONTRAST
BRIGHTNESS
V.POSITION
COLOR
H.SIZE
H.POSITION
TRAPEZOID
DISP.FREQ.
V.MOIRE
V.SIZE
PINCUSHION
LANGUAGE
H.MOIRE
ROTATION
DEGAUSS
RECALL
1 :
CONTRAST
: 2
2) Adjustment screen (example: horizontal position adjustment)
Name of adjustment screen
Adjustment icon
The adjustment level is shown by both a number
and a bar. It can be varied with the front
buttons.
H.POSITION
50
/
1
:
:
2
When the
size adjustment screen appears.
button is pressed, the horizontal
2
End Button
When the
the adjustment level is stored,
the adjustment screen is ended
and the menu screen returns.
button is pressed,
1
On the adjustment screen where these two adjustment
icons appear, it is possible to switch between the two
screens by pressing the button.
2
NOTE: The amount of adjustment depends upon how long you depress the adjustment button. You might
have to tap the button to obtain the desired results.
113393-0A-E.pm6
4
8/1/00, 6:38 PM
E-5
VERTICAL SIZE adjustment
Fills the viewable area vertically.
Press the button to make the image smaller,
or press the button to make it larger. Press
the key toggles between VERTICAL SIZE
2
INDIVIDUAL
ADJUSTMENT
CONTRAST adjustment
Adjust the screen contrast to match your
personal perference.
and VERTICAL POSITION.
Press the
button to decrease contrast and
press the button to increase it.
Direct operation: You can access the
VERTICAL POSITION adjustment
Shifts the image on the screen vertically.
CONTRAST adjustment
screen by pressing the or
before entering the menu
screen.
Press the
button to move it downward, or
press the button to move it upward.
2
Press the key toggles between VERTICAL
SIZE and VERTICAL POSITION
2
Press the key toggles between CONTRAST
and BRIGHTNESS.
PINCUSHION adjustment
The image can be corrected for barrel
distortion.
Press the button or the button to eliminate
curved vertical lines.
BRIGHTNESS adjustment
Adjusts the brightness to get the desired
background level.
Press the
button to make the background
2
Press the key toggles between VERTICAL
lighter, the button to make it darker.
PINCUSHION and TRAPEZOIDAL
correction.
2
Press the key toggles between CONTRAST
and BRIGHTNESS.
TRAPEZOID adjustment
The image can be corrected for the trapezoidal
distortion.
HORIZONTAL SIZE adjustment
Fills the viewable area horizontally.
Press the button to make the image narrower,
or press the button to make it wider.
Press the
press the button to make the top edge wider.
Press the key toggles between
button to narrow the top edge, or
Press the
2
key toggles between
2
HORIZONTAL SIZE and HORIZONTAL
POSITION.
PINCUSHION and TRAPEZOID correction.
ROTATION adjustment
The image can be corrected for tilt picture.
Press the button to tilt the image to the left,
HORIZONTAL POSITION adjustment
Shifts the image on the screen horizontally.
Press the button to move the screen image to
the left, or press the button to move it to the
right.
or press the
right.
button to tilt the image to the
2
Press the
key toggles between
HORIZONTAL SIZE and HORIZONTAL
POSITION.
113393-0A-E.pm6
5
8/1/00, 6:38 PM
E-6
COLOR selection
MANUAL DEGAUSSING
After moving the selector to the degauss icon,
The white in the image can be adjusted.
1) Use the
button to select: (1)9300OK,
press the
takes place a few seconds later.
button. The degaussing action
2
(2)6500OK or (3)the user’s preferred color.
2) If the (3):the user’s color is selected, “2”
appears in the lower right of the On-Screen
Menu.
NOTE: A sharp snap noise may be heard when
degaussing occurs. This is normal.
Press the front 2 button to display the USER
COLOR adjustment screen.
MEMORY RECALL
It is possible to restore adjustments to the
original factory settings. If the monitor is
operating in a user defined mode, this control
has no effect.
USER COLOR
The white in the video image can be adjusted
to the user’s preferred color.
1) Use the
(blue).
2) Use the
desired.
button to select R (red) or B
button to adjust the color as
2
HORIZONTAL MOIRE
Reduce the dark wavy line Moire pattern on
the screen.
Press the
or
button to minimize the
*The GREEN color is fixed and cannot be
adjusted.
horizontal moire image on the screen.
IMPORTANT-Memory recall of the user’s
color is not possible, so take note of the initial
setting before adjusting.
When the monitor is turned OFF, user color
keeps the last adjustment.
VERTICAL MOIRE
Reduce the dark wavy line Moire pattern on
the screen.
Press the
or
button to minimize the
vertical moire image on the screen.
LANGUAGE selection
The language of the On-Screen Menu can be
selected among English, French, German,
Italian and Spanish. Select with the
buttons.
DISP. FREQ (Input frequency display)
This displays the input synchronization signal
frequency.
It identifies the horizontal and vertical
frequency sent to the monitor from the video
card currently in use.
113393-0A-E.pm6
6
8/1/00, 6:38 PM
E-7
TROUBLESHOOTING
SERVICING
If your monitor fails to operate functionally, it might
be possible to correct the problem by making simple
checks as follows:
Refer all servicing to qualified service personnel.
Serious shock hazards exist within the covers of
this monitor.
Do not open the covers under any circumstances-
there are no serviceable parts inside.
Problem
Check and Adjust
Blank screen
(* NOTE)
·
Monitor power switch,
power cord, signal cable,
or connector
·
·
computer power switch
Brightness and Contrast
controls
SIGNAL CONNECTOR
INFORMATION
Display position
off-center
·
·
·
Vertical centering and
horizontal phase controls
5
1
Display too small
or too large
Vertical and horizontal
size controls
Display too bright
or too dim
Brightness and Contrast
controls
Refer to the operation instructions for your computer
or video adapter to ensure that you have the correct
signal output source for the monitor. Ensure that the
switches on the video adapter are set correctly for
operation with this monitor.
15
Pin
1
Function
Red signal
Green signal
Blue signal
Ground
Pin
9
Function
5V
Digital ground
If the above steps fail to correct the problem contact
your dealer for servicing by qualified service
personnel.
2
10
3
11 Ground
4
12 SDA (DDC1/DDC2B)
You must include the power cord if you return the
monitor for service.
Horizontal
13
5
6
* (NOTE)
Synchronization
* NOTE: You can easily distinguish the problem is
on the monitor or on the computer by
using the monitor’s built-in selftest
function.
Vertical synchronization
14
Red return
and VCLK (DDC1)
Green
return
7
8
15 SCL (DDC 2B)
With the monitor power ON, disconnect
the signal cable from monitor. If there is
no image on the monitor screen,
disconnect the signal cable. If you see a
“NO SIGNAL” image on the screen
(shown below), the monitor is function
properly, and the problem is at computer
side, or signal cable.
Blue return
*NOTE :This pin is used for self-test detection; at
computer side, this pin has to be connected
to ground.
NO SIGNAL
113393-0A-E.pm6
7
8/1/00, 6:38 PM
E-8
TECHNICAL SPECIFICATIONS
1 5- in. vis ual d ia gona l
Vie wa b le s c re en size 1 3 .8 "
A nt i- G la r e C o at ing* *
P owe r In pu t
Vol ta g e
F re qu e nc y
S cre e n S ize
1 00 t o 2 40
V
A C
5 0
-
60 H z
C urre n t
R at in g
D ot P i tc h
0 .2 8 m m (0 .0 1 in. )
1 .8
A
D is pl a y Are a
D e f au l t
1 96 x 2 6 2 mm
( 7. 7 x 1 0. 3 in. ), typica l
2 11 x 2 8 2 mm
P owe r
C on s u m pt i on
7 0
W
(m a ximum )
F ul l S ca n
( H
x
W)
( 8. 3 x 11. 1 in. ), d e pe nd s
o n signa l timing
371 x 391 x 399 mm
(14.6 x 15.4 x 15.7 in.)
D is pl a y Co l ors
I nfinite
D im e n s io n
We i gh t
M ax . R e s ol u ti on
1 02 4 D ot s x 76 8 L ine s
1 3. 5 k g (2 9. 5 lb)
A ll gr ap hic m od e s with
hor izo nta l fr eq uenc ie s
b et we e n 30 K H z to 6 9
K Hz
O pe ra t in g
Te m p e rat u re
1 0° C t o 35 °C
( 50 °F to 9 5° F )
C om p at ib i li ty
S yn ch ron i za ti o n
H orizo nt a l:
Ve rti c al :
S to ra g e
Te m p e rat u re
- 20 °C to 4 5° C
( - 1 6° F t o 11 3 °F )
3 0 to 6 9 K Hz
5 5 to 1 2 0 Hz
2 0% t o 8 0%
( no n- c ond ensing)
B an dwi dt h
9 4. 5 M Hz
H um id i ty
A lt it u de
Vid eo RG B Ana lo g
S ync. TT L S e p ar a te
U p to 2 1 33 .6
( 70 00 ft)
m
I np ut S i gn a l
M P R 1 9 90 :1 0 ,
T C O 9 5 / 99
O pt io nal
S ig na l C ab l e
1 5- pin D - s ub co nne ct o r
M PR I I / TC O
*
Specifications are subject to change without notice.
** TCO version has a different surface treatment.
*** This product is ERGONOMICS APPROVED.
113393-0A-E.pm6
8
8/1/00, 6:38 PM
E-9
PRESET MODES
Resolution
(H x V)
H. Freq. V. Freq.
Resolution
(H x V)
H. Freq. V. Freq.
M ode
M ode
(KHz)
31.4
31.4
35.0
37.8
37.5
43.3
46.8
(Hz)
(KHz)
48.3
53.6
56.4
60.0
64.3
68.6
(Hz)
1
2
3
4
5
6
7
720 x 400
640 x 480
640 x 480
800 x 600
640 x 480
640 x 480
800 x 600
70
8
1024 x 768
800 x 600
60
60
9
85
66
10
11
12
13
1024 x 768
1024 x 768
1280 x 1024
1024 x 768
70
60
75
75
60
85
85
75
113393-0A-E.pm6
9
8/1/00, 6:38 PM
|