Operating Instructions
HOB
Contents
GB
Installation, 2-3
Positioning
Electrical connection
GB
Description of the appliance, 4
Control panel
English,1
Start-up and use, 5-8
Switching on the hob
Switching on the cooking zones
Booster function
Switching off the cooking zones
Programming the cooking duration
Timer
Control panel lock
Switching off the hob
“Demo” mode
CIO 644 DD Z
CIO 642 DD B
Practical advice on using the appliance
Safety devices
Practical cooking advice
Precautions and tips, 9
General safety
Disposal
Care and maintenance, 10
Switching the appliance off
Cleaning the appliance
Disassembling the hob
Technical description of the models, 11
After Sales Service, 14
Guarantee, 15
Key Contacts, 16
Voltage and mains frequency
• 400V - 2+N ~ 50 Hz
/ixing
GB
The appliance must be installed on a perfectly level
supporting surface.
• 220-240V 3 ~ 50 Hz
• 400V 3 - N ~ 50 Hz
Any deformities caused by improper fixing could affect
the features and operation of the hob.
• 400V - 2+2N ~ 50 Hz
Separate the wires and connect them in accordance
with the instructions given in the following table and
diagrams:
The thickness of the supporting surface should be
taken into account when choosing the length of the
screws for the fixing hooks:
Voltage and
Electrical cable
Wire connection
• 30 mm thick: 23 mm screws
• 40 mm thick: 13 mm screws
mains frequency
400V - 2+N ~
50 Hz
: yellow/green;
N: the two blue wires together
L1: black
8ix the hob as follows:
220-240V 3 ~
50Hz
1. Use short flat-bottomed screws to fix the 4
alignment springs in the holes provided at the central
point of each side of the hob.
L2: brown
400V 3-N~ 50Hz
: yellow/green;
N1: blue
2. Place the hob in the cavity, make sure it is in a
central position and push down on the whole perimeter
until the hob is stuck to the supporting surface.
3. 8or hobs with raised sides: After inserting the hob
into its cavity, insert the 4 fixing hooks (each has its
own pin) into the lower edges of the hob, using the
long pointed screws to fix them in place, until the
glass is stuck to the supporting surface.
400V - 2+2N ~
50 Hz
N2: blue
L1: black
L2: brown
Connecting the electricity supply cable to the mains
If the appliance is being connected directly to the
electricity mains an omnipolar switch must be installed
with a minimum opening of 3 mm between contacts.
! The installer must ensure that the correct electrical
connection has been made and that it is fully
compliant with safety regulations.
! The screws for the alignment springs must remain
accessible.
! In order to adhere to safety standards, the appliance
must not come into contact with electrical parts once it
has been installed.
Before connecting the appliance to the power supply,
make sure that:
• The appliance is earthed and the plug is compliant
with the law.
! All parts which ensure the safe operation of the
appliance must not be removable without the aid of a
tool.
• The socket can withstand the maximum power of the
appliance, which is indicated on the data plate
located on the appliance itself.
• The voltage falls within the range of values indicated
on the data plate.
Electrical connection
• The socket is compatible with the plug of the
appliance. If the socket is incompatible with the
plug, ask an authorised technician to replace it. Do
not use extension cords or multiple sockets.
! Once the appliance has been installed, the power
supply cable and the electrical socket must be easily
accessible.
! The electrical connection for the hob and for any built-
in oven must be carried out separately, both for safety
purposes and to make extracting the oven easier.
Single-phase connection
The hob is equipped with a pre-connected electricity
supply cable, which is designed for single-phase
connection. Connect the wires in accordance with the
instructions given in the following table and diagrams:
Voltage and
! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced
by authorised technicians only.
Electrical cable
Wire connection
mains frequency
! The manufacturer declines any liability should
these safety measures not be observed.
! Do not remove or replace the power supply cable for
any reason. Its removal or replacement will void the
warranty and the CE marking. INDESIT does not
assume liability for accidents or damage arising from
replacement/removal of the original power supply
cable. Replacement can only be accepted when
carried out by personnel authorised by INDESIT and
using an original spare part.
: yellow/green;
N: the two blue wires
together
L: brown and black
together
220-240V 1+N ~
50 Hz
Other types of connection
If the mains supply corresponds with one of the
following:
3
Description of the
appliance
Control panel
GB
The control panel described in this manual is only a representative example: it may not exactly match the panel
on your appliance.
BOOSTER
BOOSTER
indicator light
button
Booster
Booster
Booster
Booster
• COOKING ZONE PROGRAMMED indicator lights
show which cooking zones are being used during
a cooking programme (see Start-up and use).
• INCREASE TIME button increases the time value
set on the timer (see Start-up and use).
• DECREASE TIME button decreases the time
• CONTROL PANEL LOCK button prevents
accidental changes to the hob settings (see Start-
up and use).
value set on the timer (see Start-up and use).
• COOKING ZONE SELECTOR button shows a
particular cooking zone has been selected and
therefore various adjustments are possible.
• CONTROL PANEL LOCK indicator light shows
the control panel has been locked (see Start-up
and use).
• COOKING ZONE SELECTOR button is used to
select the desired cooking zone.
• COOKING ZONE POWER SELECTOR buttons
switch on the hotplate and control the power (see
Start-up and use).
• POWER indicator provides a visual display for the
current heat level.
• TIMER indicator light shows that the timer has
been activated
• ON/O// button switches the appliance on and off.
• ON/O// indicator light shows whether the
appliance is on or off.
• BOOSTER button activates the booster function -
3000 W - of the cooking zone (see Start-up and
use).
• PROGRAMME TIMER button controls the cooking
programme times (see Start-up and use).
• BOOSTER indicator light shows that the booster
function has been activated.
• PROGRAMME TIMER display shows which
programme has been selected (see Start-up and
use).
4
Start-up and use
! The glue applied on the gaskets leaves traces of
grease on the glass. Before using the appliance, we
recommend you remove these with a special non-
abrasive cleaning product. During the first few hours of
use there may be a smell of rubber which will
disappear very quickly.
Switching on the hob
GB
To switch the hob on, press and hold the
for approximately one second.
button
Switching on the cooking zones
! A few seconds after the hob is connected to the
electricity supply, a buzzer will sound. The hob may
now be switched on.
Each cooking zone is controlled using a selector
button and a power adjustment device consisting
of power level selector buttons between the values of 0
and 9.
Types of noise during normal hob operation:
• Buzz: due to the vibration of the metallic parts that
make up the induction element and the pot; it is
generated by the electromagnetic field required for
heating and increases as the power of the induction
element increases.
• To begin operating a cooking zone, press the
corresponding control button and set the desired
power level using the power level selector buttons
between 0 and 9.
• Soft whistle: heard when the pot placed on the
heating zone is empty; the noise disappears once
food or water is placed into the pot.
Switching off the cooking zones
To switch off a cooking zone, select it using the
• Crackle: produced by the vibration of materials on
the bottom of the pot due to the flow of parasitic
currents caused by electromagnetic fields
corresponding selector button
and:
• Press power level selector button 0: this
immediately returns the power setting to 0 and the
cooking zone switches off.
(induction); can be more or less intense depending
on the material making up the bottom of the pot,
and decreases as the pot dimensions increase.
• Loud whistle: heard when two induction elements
of the same group function simultaneously at
maximum power and/or when the booster function is
set on the larger element while the other is auto-
adjusted. Noise is reduced by decreasing the power
level of the auto-adjusted induction element; pot
bottom layers made of different kinds of materials
are among the main causes of this noise.
Booster function
The booster function for some of the cooking zones
may be used to shorten heating-up times. It may be
Booster
activated by pressing the
button. The indicator
light directly above the button will illuminate. This
function boosts the power to 2000 W or 3000 W,
depending on the size of the relevant cooking zone.
The booster stops automatically after 4 minutes. While
the booster for one of the cooking zones is active, the
corresponding front or rear cooking zone will operate at
a reduced power level (e.g. if the booster for the rear
left-hand hotplate has been activated, the power level
of the front left-hand hotplate will be reduced). ,or
further information, please refer to the Technical
description of the models.
• ꢀan noise: a fan is necessary to ensure the hob
functions correctly and to safeguard the electronic
unit from possible overheating. The fan functions at
maximum power when the large induction element is
at maximum power or when the booster function is
on; in all other cases, it works at average power
depending on the temperature detected.
,urthermore, the fan may continue to work even after
switching the hob off, if the temperature detected is
high.
Programming the cooking duration
The types of noise listed above are due to induction
technology and are not necessarily operational faults.
! All the cooking zones may be programmed
simultaneously, for a duration between 1 and 99
minutes.
! If the
-
or
+
button is pressed for an extended
period of time, the display scrolls quickly though the
power levels and timer minutes.
1. Select the cooking zone using the corresponding
selector button.
2. Adjust the temperature.
3. Press the
programming button.
5
The timer begins counting down immediately. When
the time has elapsed, a buzzer will sound (for one
minute).
4. Set the cooking duration using the
-
and
+
GB
buttons.
5. Confirm by pressing the
button.
Control panel lock
The timer begins counting down immediately. A
buzzer sounds for approximately 1 minute and the
cooking zone switches off when the set programme
has finished.
When the hob is switched on, it is possible to lock the
oven controls in order to avoid accidental changes
being made to the settings (by children, during
Repeat the above procedure for each hotplate you
wish to programme.
cleaning, etc.). Press the
button to lock the
control panel: the indicator light above the button will
switch on.
Using multiple programmes and the display
To use any of the controls (e.g. to stop cooking), you
If one or more hotplates are programmed, the display
will show the data for the hotplate with the least time
remaining, and the light corresponding to the position
of the hotplate will flash. The lights corresponding to
the other hotplates programmed will be switched on.
To display the time remaining for the other
must switch off this function. Press the
button for
a few moments, the indicator light will switch off and
the lock function will be removed.
Switching off the hob
programmed hotplates, press the
button
Press the
button to switch the appliance off.
repeatedly. The times remaining for each hotplate will
be shown in a clockwise order, beginning with the front
left hotplate.
If the control panel lock has been activated, the
controls will continue to be locked even after the hob is
switched on again. In order to switch the hob on again,
you must first remove the lock function.
Changing the programme
“Demo” mode
1. Press the
button repeatedly until the duration
It is possible to set the hob to a demonstration mode
where all the controls work normally but the heating
elements do not switch on. To activate the “demo”
mode the hob must be switched on, with all the
hotplates switched off.
you wish to change is shown.
2. Use the
buttons to set the new duration.
3. Confirm by pressing the
button.
To cancel a programme, follow the above instructions.
At step 2, press the button: the duration decreases
• Press and hold the
+
and
-
buttons
simultaneously for 6 seconds. When the 6 seconds
have elapsed, the ON/O,, and CONTROLS
-
progressively until it reaches 0 and switches off. The
programme resets and the display exits programming
mode.
LOCKED indicator lights will flash for one second.
Release the
button;
+
and
-
buttons and press the
Timer
• The display will show the text DE and MO and the
hob will be switched off.
The hob must be switched on.
The timer can be used to set a duration up to 99
minutes.
• When the hob is switched on again it will be set to
the “demo” mode.
1. Press the
programming button until the timer
To exit this mode, follow the procedure described
above. The display will show the text DE and O, and
the hob will be switched off. When it is next switched
on, the hob will function normally.
indicator light is illuminated.
2. Set the desired duration using the
-
and
+
buttons.
3. Confirm by pressing the
button.
6
are still at a high temperature. If the power display
shows , the cooking zone is still hot. It is possible,
Practical advice on using the appliance
GB
! Use cookware made from materials which are
compatible with the induction principle (ferromagnetic
material). We especially recommend pans made from:
cast iron, coated steel or special stainless steel
adapted for induction. Use a magnet to test the
compatibility of the cookware.
for example, to keep a dish warm or melt butter or
chocolate. As the cooking zone cools, the power
display will show
. The display switches off when
the cooking zone has cooled sufficiently.
SUITABLE
UNSUITABLE
Overheating protection
If the electronic elements overheat, the hob switches
off automatically and
ꢀ
appears on the display,
followed by a flashing number. When the temperature
has reached a suitable level, this message disappears
and the hob may be used again.
*
Copper,
Cast iron
Enamelled steel
Special stainless steel
Aluminium, Glass, Earthenware,
Ceramic, non magnetic Stainless steel
In addition, to obtain the best results from your hob:
• Use pans with a thick, flat base in order to fully
utilise the cooking zone.
Safety switch
The appliance has a safety switch which automatically
switches the cooking zones off after they have been in
operation for a certain amount of time at a particular
power level. When the safety switch has been
triggered, the display shows “0”.
,or example: the right rear hotplate is set to 5 and will
switch off after 5 hours of continuous operation, while
the front left hotplate is set to 2 and will switch off after
8 hours.
• Always use pans with a diameter which is large
enough to cover the hotplate fully, in order to use all
the available heat.
Maximum operating
Power level
time in hours
1
2
3
4
5
6
7
8
9
9
8
7
6
5
4
3
2
1
• Make sure that the base of the cookware is always
clean and dry, in order to fully utilise and extend the
life of both the cooking zones and the cookware.
• Avoid using the same cookware which has been
used on gas burners: the heat concentration on gas
burners may distort the base of the pan, causing it
not to adhere correctly.
Safety devices
Pan sensor
Buzzer
Each cooking zone is equipped with a pan sensor
device. The hotplate only emits heat when a pan with
suitable measurements for the cooking zone is placed
on it. If the indicator light is flashing, it may indicate:
• An incompatible pan
This can also indicate several irregularities:
• An object (a pan, cutlery, etc.) has been placed on
the control panel for more than 10 seconds.
• Something has been spilt on the control panel.
• A button has been pressed for too long. All of the
above situations may cause the buzzer to sound.
Remove the cause of the malfunction to stop the
buzzer. If the cause of the problem is not removed,
the buzzer will keep sounding and the hob will
switch off.
• A pan whose diameter is too small
• The pan has been removed from the hotplate.
Residual heat indicators
Each cooking zone is equipped with a residual heat
indicator. This indicator signals which cooking zones
7
Practical cooking advice
GB
Pressure cooking
Pressure cooker
Frying
Boiling
ª
•
Grilling
•
¶
Crêpes
Cooking on a high flame and browning
(roasts, steaks, escalopes, fish fillets,
fried eggs)
¶
§
Fast thickening (liquid juices)
Boiling water (pasta, rice, vegetables)
Milk
§
S
Slow thickening (dense juices)
S
¢
Bain-marie cooking
Pressure cooking after whistle
¢
£
™
-{}-
Low-flame cooking
(stews)
Reheating dishes
™
¡
Chocolate sauce
Keeping food hot
8
Precautions and tips
! This appliance has been designed and manufactured in
the centre of the hob in order to avoid accidental
burns.
GB
compliance with international safety standards. The
following warnings are provided for safety reasons and
must be read carefully.
• When unplugging the appliance, always pull the plug
from the mains socket; do not pull on the cable.
• Never perform any cleaning or maintenance work
without having disconnected the appliance from the
electricity mains.
This appliance conforms to the following European
Economic Community directives:
- 2006/95/EEC dated 12/12/06 (Low Voltage) and
subsequent amendments;
• The appliance should not be operated by people
(including children) with reduced physical, sensory or
mental capacities, by inexperienced individuals or by
anyone who is not familiar with the product. These
individuals should, at the very least, be supervised by
someone who assumes responsibility for their safety or
receive preliminary instructions relating to the operation
of the appliance.
-89/336/EEC dated 03/05/89 (Electromagnetic
Compatibility) and subsequent amendments;
- 93/68/EEC dated 22/07/93 and subsequent amendments.
General safety
! Make sure that the air inlet behind the fan grille is never
obstructed. The built-in hob should, in fact, be provided
with suitable ventilation for the cooling of the electronic
components used in the appliance.
• ꢀor the attention of wearers of pacemakers or
other active implants:
The hob complies with all current standards on
electromagnetic interference.
! We advise against the installation of an induction hob
above an under-the-counter refrigerator (heat) or above a
washing machine (vibrations). In fact, there would be
insufficient space for the ventilation of electronic
components.
Your induction hob is therefore perfectly in keeping with
legal requirements (89/336/CEE directives). It is
designed not to create interference on any other
electrical apparatus being used on condition that the
apparatus in question also complies with this
legislation.
• The appliance was designed for domestic use inside the
home and is not intended for commercial or industrial
use.
Your induction hob generates short-range magnetic
fields.
• The appliance must not be installed outdoors, even in
covered areas. It is extremely dangerous to leave the
appliance exposed to rain and storms.
To avoid any interference between your induction hob
and a pacemaker, the latter must be designed to
comply with relevant regulations.
• Do not touch the appliance when barefoot or with wet
or damp hands and feet.
In this respect, we can only guarantee our own product
conformity. Please consult the pacemaker manufacturer
or your doctor concerning its conformity or any possible
incompatibility.
• The appliance must be used by adults only for the
preparation of food, in accordance with the instructions
provided in this booklet. Do not use the hob as a
worktop or chopping board.
• Do not let children play with the appliance.
• The glass ceramic hob is resistant to mechanical
shocks, but it may crack (or even break) if hit with a
sharp object such as a tool. If this happens,
disconnect the appliance from the electricity mains
immediately and contact a Service Centre.
Disposal
• When disposing of packaging material: observe local
legislation so that the packaging may be reused.
• The European Directive 2002/96/EC relating to Waste
Electrical and Electronic Equipment (WEEE) states that
household appliances should not be disposed of using
the normal solid urban waste cycle. Exhausted
appliances should be collected separately in order to
optimise the cost of re-using and recycling the materials
inside the machine, while preventing potential damage
to the atmosphere and to public health. The crossed-
out dustbin is marked on all products to remind the
owner of their obligations regarding separated waste
collection.
• Ensure that power supply cables of other electrical
appliances do not come into contact with the hot parts
of the hob.
• Remember that the cooking zones remain relatively hot
for at least thirty minutes after they have been switched
off. An indicator light provides a warning when residual
heat is present (see Start-up and use).
• Keep any object which could melt away from the hob,
for example plastic and aluminium objects, or products
with a high sugar content. Be especially careful when
using plastic film and aluminium foil or packaging: if
placed on surfaces which are still hot, they may cause
serious damage to the hob.
,or further information relating to the correct disposal of
exhausted household appliances, owners may contact
the public service provided or their local dealer.
• Always make sure that pan handles are turned towards
9
Careandmaintenance
Switching the appliance off
Stainless steel frame (only in models with outer
frame)
GB
Disconnect your appliance from the electricity
supply before carrying out any work on it.
Stainless steel can be marked by hard water which
has been left on the surface for a long time, or by
cleaning products containing phosphorus.
Cleaning the appliance
After cleaning, it is advisable to rinse the surface
well and dry it thoroughly. If water is spilt on the
surface, dry it quickly and thoroughly.
! Do not use abrasive or corrosive detergents (for
example, products in spray cans for cleaning
barbecues and ovens), stain removers, anti-rust
products, powder detergents or sponges with
abrasive surfaces: these may scratch the surface
beyond repair.
! Some hobs have an aluminium frame which is
similar to stainless steel. Do not use any cleaning or
degreasing products which are not suitable for use
with aluminium.
! Never use steam cleaners or pressure cleaners on
the appliance.
Disassembling the hob
• It is usually sufficient simply to wash the hob
using a damp sponge and dry it with absorbent
kitchen towel.
If it is necessary to disassemble the hob:
1. Loosen the screws fixing the alignment springs on
each side.
2. Loosen the screws holding the fixing hooks in
each corner.
3. Take the hob out of its installation cavity.
• If the hob is particularly dirty, rub it with a special
glass ceramic cleaning product, then rinse well
and dry thoroughly.
! Do not attempt to repair the appliance yourself. If
the appliance breaks down, contact a Service
Centre.
• To remove more stubborn dirt, use a suitable
scraper. Remove spills as soon as possible,
without waiting for the appliance to cool, to avoid
residues forming crusty deposits. You can
achieve excellent results by using a rust-proof
steel wire sponge - specifically designed for
glass ceramic surfaces - soaked in soapy water.
• If any plastic or sugary substances are
accidentally melted on the hob, remove them
immediately with the scraper, while the surface is
still hot.
• Once it is clean, the hob may be treated with a
special protective maintenance product: the
invisible film left by this product protects the
surface from drips during cooking. This
maintenance task should be carried out while the
appliance is warm (not hot) or cold.
• Always remember to rinse the appliance well with
clean water and dry it thoroughly: residues can
become encrusted during subsequent cooking
processes.
10
Technical description of
the models
The induction system is the quickest existing way of cooking. Unlike traditional hotplates where the cooking
zone heats up, with the induction system heat is generated directly inside pans which have ferromagnetic
bases.
GB
Hobs
Cooking zone
Back Left
Back Right
Front Left
Front Right
Total power
CIO 642 DD B
Power (W)
CIO 644 DD Z
Power (W)
I 1400 – 600 se Ant. Sx*
I 2200 – B 3000*
I 2200 – B 3000*
I 1400 – 600 se Post. Dx*
7200
I 1400 – B 2000* – 600 se Ant. Sx*
I 2200 – B 3000* - 1600 se Ant. Dx*
I 2200 – B 3000* - 1600 se Post. Sx*
I 1400 – B 2000* – 600 se Post. Dx*
7200
Key:
I = single induction cooking zone
B = booster: the power level of the cooking zone may be boosted to 3000 W
* = the maximum power level is limited while the booster is activated for the relevant rear cooking zone (see
Start-up and use).
11
GB
12
GB
13
After Sales Service
GB
"No company is better positioned to offer an after sales service on a
Hotpoint appliance than us - the manufacturer"
As part of our commitment to you, all Hotpoint appliances have the added benefit of a fully inclusive parts and
labour guarantee for the first 12 months. In addition to this you also have the advantage of free
replacement parts for the first 5 years when fitted by a Hotpoint
engineer. When the 12 months parts and labour guarantee expires we offer the following after sales service
options:
Repair Service and Information Help Desk
UK: 08709 066066
Republic of Ireland: 1850 302 200
Note: Our operators will require the Model number and the Serial number of your appliance
Available 364 days a year with a fast, effective and value for money service. We have the largest white goods
repair service in the UK with over 1200 of our own fully trained engineers. All repairs include a parts and labour
guarantee for 12 months from the date of the repair.
If you require any information or have any questions about your appliance, our operators are on hand with help
and advice.
All this ensures that you will receive the best available after sales service possible.
Extended Warranties
UK: 08709 088 088
Republic of Ireland: 1850 502 200
Whether you have just one or a number of Hotpoint appliances in your kitchen, we offer two service cover plans
to give you total peace of mind.
● Repair Protection Plan -
● Kitchen Cover
ꢀREE service repairs for a single Hotpoint appliance during the period
of cover.
-
ꢀREE service repairs for all your Hotpoint appliances less than 8
years old.
Genuine Parts and AccessoriesUK: 08709 077 077
Republic of Ireland: (01) 842 6836
A wide range of genuine parts and accessories are available from our hotline or through our web site.
Genuine parts and accessories, extended warranties and service repairs are all
available on our web-site at:
14
Guarantee
GB
"Satisfaction guaranteed or your money back"
We give you a unique 'satisfaction guaranteed' promise - valid for 90 days - after you have
purchased your Hotpoint appliance. If there is a technical problem simply call Hotpoint Repair
service or visit our web-site at www.theservicecentre.co.uk and where necessary, we will arrange for
an engineer to call. If the technical problem is not resolved under this guarantee, we will replace
your machine or, if you prefer, give you your money back.
All Hotpoint appliances carry a fully inclusive 12 month parts and labour guarantee as well as free
replacement parts for the first 5 years (except microwaves, selected integrated appliances and
cooker hoods, which have a one year guarantee) provided that they are fitted by a Hotpoint engineer.
Guarantee terms and conditions
Your guarantee is only applicable in the United Kingdom or Republic of Ireland and is subject to the
following provisions that your appliance:
●
●
Has been installed and used correctly in accordance with this instruction booklet.
Has been used solely for domestic purposes and is located on domestic premises (ie. not for
commercial or trade use).
●
●
Has been properly connected to a suitable electrical supply voltage as stated on the appliance
rating plate.
Has not been subject to misuse, accident, modified or repaired by anyone other than one of our
own service engineers.
*or pre purchase information on any other Hotpoint product call: 08701 50 60 70
Recycling & Disposal Information
As part of Hotpoint's continued commitment to helping the environment, Hotpoint reserves the right to
use quality recycled components to keep down customer costs and minimise material wastage.
Please dispose of packaging and old appliances carefully.
To minimise risk of injury to children, remove the door, plug and cut mains cable off flush with the
appliance. Dispose of these parts separately to ensure that the appliance can no longer be plugged
into a mains socket, and the door cannot be locked shut.
15
04/2008 - 195069879.00
XEROX BUSINESS SERVICES
Key Contacts
GB
After Sales Service
Over 1200 trained specialists, directly employed by us, ensure that you can have complete
confidence in both the appliances and services we offer.
Repair Service and Information Desk
UK: 08709 066 066
(Open 8 to 8 Mon - *ri, 8 to 6 Sat, 10 to 4 Sun & Bank Holidays)
Republic of Ireland: 1850 302 200
Note: Our operators will require the following information:
Model number:
Serial number:
Extended Warranties
UK: 08709 088 088
(Open 8 to 8 Mon - Sun)
Republic of Ireland: 1850 502 200
Genuine Parts and Accessories
UK: 08709 077 077
(Open 8-30 to 5-30 Mon - *ri & 9 to 12 Sat)
Republic of Ireland: (01) 842 6836
Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB.
16
|