Hitachi Colour TV
C29-F880S
C29-F880SN
C29-F880SNT
SAFETY PRECAUTIONS
MAINTENANCE
When the power cord or plug
is damaged or frayed, unplug
this TV from the wall outlet
and refer servicing to qualified
service personnel.
Avoid dusty places, since
accumulated dust inside the
chassis may cause failure of
the set when high humidity
persists.
Do not overload wall outlets
and extension cords as this
can result in fire or electric
shock.
Do not use this TV set near
water, for example, near a
bathtub, washbowl, kitchen
sink, or laundry tub, in a wet
basement, etc.
Do not allow anything to rest
on or roll over the power cord
and do not place theTVwhere
Never cover the slots or
openings of the set with cloth
or other material.
to
the power cord is subject
trafficorabuse.This mayresult
in a shock or fire hazard.
If theTVset has been
or the cabinet has been
Never block the bottom
ventilation slots of the set by
placing it on a bed, sofa, rug,
etc.
dropped
damaged, unplug this
from the wall outlet
and refer
TV set
qualified service
servicing to
personnel.
Never push objects of any
kind into this TV set through
cabinet slots as they may
touch dangerous voltage
points or short out parts that
Never place the set near or
radiator or
over
register.
a
heat
electric
could result in a fire or
shock.
Do not attempt to service this
TV yourself as opening or
removing covers may expose
you to dangerous voltage.
Refer all servicing to qualified
service personnel.
Never place the set in
built-inenclosure, unless
proper ventilation is provided.
a
Do not place this TV seton an
unstable cart, stand or table.
The TV set may fall,
causing
The TV set shall not be
exposed to dripping or
splashing and that no objects
filled with liquids, such as
vases, shall be placed on the
TV set.
serious injury to
human and
serious damage
appliance.
to the
3
MAINTENANCE
Choose a place where light
not
(artificial or sunlight) does
shine directly on the screen.
If a strange sound or smell
gives off from this set, please
turn off the television and
unplug from the wall outlet,
then refer
personnel.
to
service
If the set does not work
properly:
If you are unable to restore
normal operation by following
To prevent fire, never place
any type of candle or naked
flames on the top or near the
TV set.
the
TROUBLESHOOTING
section in your operating
manual, do not attempt any
further adjustment. Unplug
the set and consult service
personnel.
Adjust only those controls
that are covered in the
operating manual as improper
Avoid any kind of impact to
your television. Be special
careful not to damage the
screen face.
adjustment of other
controls
may result in
damage,
ask your service personnel
please
to
restore
operation.
the set to normal
Lightning:
In order not to damage the
parts in the set, unplug and
When going out:
If your television set is set to
remain unused for a periodof
time, turn off the television
and unplug it from the wall
outlet.
remove
connection during lightning.
the
antenna
4
SETUP
Insert The Batteries
1
2
Removethebattery cover by pressingitand sliding itdown.
Insertthetwo1.5V(AAA size) batteriesmaking sure the polarity (+or -) of the
batteries matchesthepolaritymarksinside the unit.
3
Replacethebattery cover by sliding it in untilyou hear aclick sound.
Precautions when using batteries
Do not use old and new batteries together.
Do not use different types of batteries (for example, Manganese and Alkaline batteries)
together.
Note that there are chargeable and non-chargeable batteries. Do not attempt to charge
non-chargeable batteries.
Remove the batteries from the remote control unit if you do not intend to use the unit for a long
time.
Precautions when using the remote control unit
Do not drop the remote control unit.
Do not subject the remote control unit to physical shocks.
Keep the remote control unit dry. Wetting it may cause the unit to malfunction.
Replace the batteries with new ones when operation of the unit deteriorates.
5
FUNCTIONAL PARTS
4
5
5
3
2
1
PROG.
MENU
TV/AV
6
7
8
9
To turn the TV power ON
Press the power switch on the TV set to switch on the TV.
When the TV set is ON ,the power indicator lights up dimly in red.
Standby Mode
At standby mode, the power indicator lights up brightly in red.
You can switch on the TV set or switch it to standby mode using the
remote control unit. The picture usually takes a few second before appearing.
button on the
You can also press any number (0-9),
mode.
or
buttons to switch it on from standby
P -
P+
To turn the TV power OFF
Press the power switch on the TV set to switch off the TV.
When the TV set is off, the power indicator will not light up.
NOTE
If the TV set does not receive any signal for 5 minutes, it will enter standby mode.
If you are not going to use this TV set for a long time, switch off the set using
the power switch on the TV set and disconnect the power plug from the wall outlet.
Please note that the remote control unit can switch the TV set to ON or to
STANDBY mode only when the main power is ON.
6
Rear View of TV Set
1. YCbCr IN Terminals (YUV)
2. Antenna Input Socket (75 Ohm)
3. S-Video In Terminals
4. AV IN 1 Terminals
5. AV OUT Terminals
6. AC Power Cord
1
6
2
3
4
5
YCbCr IN
AV IN 1
VIDEO
AV OUT
VIDEO
Y
Cb
Cr
AUDIO
AUDIO
LEFT
AUDIO
LEFT
LEFT
RIGHT
75 ANT
S-VIDEO
RIGHT
RIGHT
Side Panel of TV Set
AV IN 2
VIDEO
1. AV IN 2 Terminals
2. Headphone Jack
LEFT
1
RIGHT
2
NOTE
For Australia only - Install an external aerial conforming to AS 1417.1 for safety purpose.
S.VIDEO and AV IN 1 (VIDEO) inputs cannot be used at the same time.
Precautions when connecting to other equipment
When using external equipment with this TV set, please read the instruction manual of the
external equipment.
Switch off all power supplies to the equipment and TV set before connection.
Always ensure that the input and output terminals are correctly connected.
7
Remote Control Unit
1
POWER ON / STANDBY button
Press this button to switch on the TV when
at standby mode or vice versa.
P+
P -
or
Press any number 0-9,
1
2
3
4
buttons will also switch on the TV from
standby mode.
2 SLEEP button
SOUND
SYS.
SLEEP
CH I/II
Press this button to set the sleep timer.
When the preset length of time has passed,
the TV set enters standby mode.
1
4
2
5
8
0
3
6
RECALL
SOUND
MODE
3
SOUND SYSTEM button
7
9
Press this button to select the correct
sound system.
PIC.
MODE
TV/AV
--/---
LANG.
STEREO/BILINGUAL SOUND button*1
4
When stereo program is received, press
this button to select STEREO or MONO.
In AV MODE ,press this button or select
STEREO, CH-L or CH-R.
When bilingual program is received, press
this button to select DUAL-1, DUAL-2 or
MONO.
SOUND
REVEAL
PIC.
SETUP
HOLD
TUNE
U.N.L
SUBPAGE
TV/TEXT
MIX
CLOCK
TYPE
GAME
LST-CH
SUBTITLE CANCEL
P
5
6
MENU
INDEX
6
5
P
The screen will display NICAM or A2 when
such broadcast is received.
Mode
STEREO Stereo mode.
MONO Mono mode.
Description
DUAL-1 Multi-sound channel for language 1.
DUAL-2 Multi-sound channel for language 2.
CH-L
CH-R
Left sound track.
Right sound track.
*2
5
6
P+
P -
buttons
CHANNEL UP
/ DOWN
Press these buttons to select channels in
ascending or descending order.
+
VOLUME UP
/ DOWN
buttons
Press these buttons to adjust the volume level
up or down.
..
8
Remote Control Unit
7
8
MUTE button
Press once to mute the sound. Press again
to restore the sound volume.
RECALL button
Press this button to display the settings on
the screen. (e.g. Channel number, system)
SOUND
SYS.
SLEEP
CH I/II
9
SOUND MODE button
Press this button to select the desired sound
mode.
1
4
2
5
8
0
3
6
7
8
USER
SPEECH
RECALL
12
11
SOUND
MODE
MUSIC
THEATER
7
9
9
PIC.
MODE
TV/AV
Sound Mode Description
--/---
10
User preset sound mode.
USER
LANG.
SPEECH
THEATER
MUSIC
Low treble and low bass level.
High treble and high bass level.
Middle treble and middle bass level.
SOUND
REVEAL
PIC.
SETUP
HOLD
TUNE
U.N.L
SUBPAGE
10
PICTURE MODE button
Press this button to select the desired
picture mode.
TV/TEXT
MIX
CLOCK
TYPE
GAME
LST-CH
SUBTITLE CANCEL
P
USER
SOFT
MENU
INDEX
RICH
STANDARD
P
Picture Mode Description
User preset picture mode.
USER
Low contrast and low brightness level.
Middle contrast and middle brightness level.
High contrast and high brightness level.
SOFT
STANDARD
RICH
11
DIGIT button
This TV allows you to select channels from
0 to 199.
Press this button to select one-digit, two-
digit or three-digit channels input options.
To select a one-digit channel (e.g. Channel
--/---
8), press this
button to change
channel selection to "-" on screen display
and press the "8" button only.
To select a two-digit channel (e.g. Channel
--/---
28), press this
button to change
channel selection to "--" on screen display
and press "2" and "8" buttons.
To select a three-digit channel (e.g. Channel
--/---
128), press this
button to change
channel selection to "1--" on screen display
and press "2" and "8" buttons.
12
CHANNEL SELECTION buttons
Press the number buttons to select a channel.
..
9
Remote Control Unit
MENU button*2
13
14
Press this button to enter the menu screens
for various optional adjustable settings.
TV/AV button *2
Press this button to switch between TV
broadcasts and AV input programs.
TV
AV1
AV2
YCbCr
S-VIDEO
SOUND
SYS.
SLEEP
CH I/II
SOUND MENU button*2
15
16
Press this button to enter into the [SOUND]
menu directly.
PICTURE MENU button*2
1
4
2
5
8
0
3
6
RECALL
SOUND
MODE
Press this button to enter into the [PICTURE]
menu directly.
SETUP MENU button*2
7
9
PIC.
MODE
TV/AV
--/---
14
17
LANG.
Press this button to enter into the [SETUP]
menu directly.
TUNE MENU button*2
17
16
15
SOUND
REVEAL
PIC.
SETUP
HOLD
TUNE
18
21
20
18
19
20
U.N.L
SUBPAGE
TV/TEXT
MIX
CLOCK
TYPE
GAME
LST-CH
Press this button to enter into the [TUNE]
menu directly.
CLOCK button*2
SUBTITLE CANCEL
19
P
MENU
INDEX
Press this button to display the preset clock
time.
GAME button*2
13
P
Press this button to enter the game provided
with this TV set. Press this button again or
button to exit.
RECALL
Buttons Actions In Game
P -
To speed up.
P+
To transform.
To shift left.
+
To shift right.
To restart the game.
MENU
LAST CHANNEL button*2
Press this button to return to previously
viewed channel.
21
NOTE
*1
Only applicable to models with NICAM and Sound Multiplex function only.
*2
See "Teletext Operations" section for details of these buttons functions in Teletext mode.
Only applicable to models with Teletext function only.
..
10
TELETEXT OPERATIONS
For models with Teletext function only.
This page shows the function of the buttons on the remote control unit when in Teletext mode.
1
TV/TEXT button
Press this button to enter Teletext mode.
Press this button the second time to
superimpose the teletext page over the TV
SOUND
SYS.
SLEEP
CH I/II
programme.
Press this button again to exit .
1
4
2
5
8
0
3
6
P -
buttons
P+
TELETEXT PAGE UP
/ DOWN
2
3
RECALL
3
Press these buttons to increase or decrease
the Teletext page number.
SOUND
MODE
7
9
PIC.
MODE
TV/AV
PAGE NUMBER SELECTION buttons
Press the number buttons to select a
Teletext page number.
--/---
6
LANG.
4
2
8
7
SOUND
REVEAL
PIC.
SETUP
HOLD
TUNE
U.N.L
SUBPAGE
4
COLOUR buttons
TV/TEXT
MIX
CLOCK
TYPE
GAME
LST-CH
1
Press these buttons to access directly to
the corresponding pages displayed at the
lower part of the Teletext screen.
SUBTITLE CANCEL
P
MENU
INDEX
5
2
5
6
INDEX button
P
Press this button to go to the index page.
LANGUAGE button
Press this button to select the Teletext
language (if applicable e.g. English or Russian).
7
8
REVEAL button
Press this button to reveal the hidden
information for some Teletext pages (e.g.
answers to puzzles or riddles). Press again
to hide the information.
U.N.L button
Press this button to change the Teletext
screen display mode through the following:
- Upper half screen enlarged
- Lower half screen enlarged
- Normal screen state
11
9
HOLD button
Press this button to hold the Teletext page
on display to prevent the page from changing.
Press again to release the hold state.
SOUND
SYS.
SLEEP
CH I/II
10
SUB PAGE button
Some Teletext pages may contain several
sub-pages which are automatically paged
in a certain cycle by the TV station. Press
this button once, "0001" will be displayed
on screen. Enter number buttons (0-9) to
look for other sub-pages if available.
If there is no sub-pages, "****" will be
displayed. Press this button again to
cancel.
1
4
2
5
8
0
3
6
RECALL
SOUND
MODE
7
9
PIC.
MODE
TV/AV
--/---
LANG.
SOUND
REVEAL
PIC.
SETUP
HOLD
TUNE
9
10
13
12
U.N.L
SUBPAGE
11 TYPE button
TV/TEXT
MIX
CLOCK
TYPE
GAME
LST-CH
Press this button to switch the Teletext type
such as west/east type directly if applicable.
SUBTITLE CANCEL
11
P
MENU
INDEX
12
SUB TITLE button
Some TV channels transmit program with
optional sub-titles.Press this button to view
sub-titles if applicable.
P
13
CANCEL button
Press this button to return to the TV mode
temporarily while searching for a required
text page. When the required text page
has been received, the page number will
be displayed at the top left of the screen.
Press this button again to display the
Teletext screen.
12
MENU SCREENS
This TV set allows you to adjust any settings by selecting from the menu screens.
SOUND
REVEAL
PIC.
SETUP
HOLD
TUNE
U.N.L
SUBPAGE
MENU
Press the
button to enter the menu
TV/TEXT
MIX
CLOCK
TYPE
GAME
LST-CH
SUBTITLE CANCEL
screens for the following optional adjustable
settings.
P
MENU
INDEX
PICTURE
EXCHANGE
SOUND
TUNE
TIME
*1
P
SETUP
This menu allows you to adjust the picture settings
according to your preference.
[PICTURE]menu
1
MENU
PIC.
Press the
button 1 time or press the
PICTURE
button directly.
Select the desired item using the
CONTRAST
BRIGHTNESS
COLOUR
SHARPNESS
HUE
75
48
48
75
0
OFF
ON
2
3
and
buttons.
P+
P -
BLACK STRETCH
COMB FILTER
+
Use the
and
buttons to adjust the settings.
MENU
Press the
to exit to TV mode.
4
button 6 times or press
PIC.
button
Selected Items
BRIGHTNESS
CONTRAST
COLOUR
Functions
Adjust brightness level.
Adjust contrast level.
Adjust colour intensity.
Adjust sharpness level.
SHARPNESS
HUE*2
Adjust the hue towards red(+)or green(-) picture tones.
Select ON toextend the blacklevels to enhancecontrast.
BLACK STRETCH
COMB FILTER*3
Select ON toreduce the discolorations in finepicture detail.
NOTE
*1 [EXCHANGE] menu will not be available in AV mode.
*2 HUE can only be selected and adjusted when receiving NTSC broadcasts.
*3 COMB FILTER cannot be set to ON when receiving no colour signal or is at S-VIDEO input
program or YUV input program.
13
This menu allows you to adjust the sound settings according to your
preference.
[SOUND]menu
1
MENU
SOUND
Press the
button 2 times or press
button directly.
buttons.
P -
SOUND
VOLUME
BASS
TREBLE
6
50
50
0
ON
ON
2
3
4
Select the desired item using the
and
P+
BALANCE
TRUBASS
SURROUND
+
Use the
and
buttons to adjust the settings.
MENU
Press the
to TV mode.
button 5 times or press SOUND button to exit
Selected Items Functions
VOLUME
BASS
Adjust volume level.
Adjust bass level.
Adjust treble level.
TREBLE
Adjust speaker sound towards left(-) orright (+)speaker.
Select ON toenjoy SRS TRUBASS sound.
BALANCE
TRUBASS *1
SURROUND
Select ON toenjoy surround soundeffect.
[TIME]menu*2
This menu allows you to set the various timer functions.
1
2
MENU
Press the
button 3 times.
TIME
CLOCK
ON TIME
ON PROG
OFF TIME
--:--
--:--
1
--:--
20
Select the desired item (e.g. Hour , minute ,channel number)
using the and buttons.
SLEEP TIMER
REMIND TIME
REMIND PROG
P+
P -
buttons to adjust the settings.
--:--
1
+
3 Use the
and
4
Press the
button 4 times to exit to TV mode.
MENU
Selected Items
CLOCK
Functions
Set the current clock time.
Set the clock time to switch on TV.
ON TIME
ON PROG
Set the channel number for ON TIME activation.
Set the clock time to switch off TV.
OFF TIME
SLEEP TIMER
REMIND TIME
REMIND PROG
Set the length of time to switch off TV.
Set the clock time to change to REMIND PROG channel.
Set the channel number for REMIND TIME activation.
NOTE
*1
is a trademark of SRS Labs , Inc.
TruBass technology is incorporated under license form SRS Labs , Inc.
*2All the timer functions will only be effective if the power of the TV set is switched off using
the remote control unit. If the power is switched off by the power button on the TV set or
a power failure occurs, the timer will be reset.
14
This menu allows you to adjust the various setup functions.
[SETUP] menu
1
MENU
SETUP
button
Press the
directly.
Select the desired item using the P+ and P - buttons.
button 4 times or press
SETUP
LANG.
ENGLISH
OFF
OFF
2
3
4
BACKGROUND
NOISE REDUCE
CHILD LOCK
OFF
+
Use the
and
buttons to adjust the settings.
button 3 times or press button to exit
MENU
Press the
to TV mode.
SETUP
Selected Items
LANG.
Functions
Select the on-screen display language.
Select ON to change screen to blue at no signal condition.
Select ON to reduce noise in weak signal picture.
Select ON to disable access to TV via buttons on TV.
BACKGROUND
NOISE REDUCE
CHILD LOCK*1
This menu allows you to set a channel to a desired TV
station.
[TUNE]menu*2
TUNE
1
MENU
TUNE
button
Press the
directly.
Select the desired item using the P+ and P - buttons.
button 5 times or press
COLOUR SYS
SOUND SYS
BAND
SKIP
PROGRAM
SEARCH
AUTO
M
VHF-L
OFF
2
2
FINE TUNE
AUTO SEARCH
+
3 Use the
and
buttons to adjust/activate the functions.
TUNE
MENU
4
Press the
to TV mode.
button 2 times or press
button to exit
Selected Items
COLOUR SYS*3
SOUND SYS
BAND
Functions
Select the appropriate colour system.
Select the appropriate sound system (i.e. I,M,DK or BG).
Select band system for tuning (i.e. VHF-L,VHF-H or UHF).
SKIP*4
Select ON to skip the channel in PROGRAM.
Set the channel number by number buttons or
--/---
button.
PROGRAM
SEARCH
FINE TUNE*5
Activate to manually search for desired broadcast stations.
Fine tune the unsatisfactory signal reception.
Activate to auto search & preset receivable broadcast stations.
AUTO SEARCH
NOTE
*1 If CHILD LOCK is set to ON, you can access the TV by remote control unit only.
You may keep the remote control unit out of reach to prevent children from any unauthorized
access to the TV.
*2 In AV mode, only COLOUR SYS will be displayed in [TUNE] menu.
*3 If COLOUR SYS is set to AUTO, the colour system will be detected and selected automatically.
If the signal reception is poor, an incorrect colour system may be detected and selected. You
can rectify this problem by setting the colour system (PAL, NTSC, NTSC4.43 or SECAM) manually.
*4 When SKIP is set to ON, the channel number will be changed from green to grey.
*5 When using FINE TUNE to adjust the signal reception, the channel number will be changed
from green to yellow; if SKIP is set to ON at the same time, the channel number will be
changed from yellow to white.
15
This menu allows you to arrange channel numbers by
exchanging between 2 preset channel numbers.
[EXCHANGE]
menu*1
1
2
MENU
Press the
button 6 times.
EXCHANGE
PROGRAM
PROGRAM
EXCHANGE
1
1
Select the first PROGRAM item using the
+
and
buttons.
P -
P+
Use the
and
buttons to select the channel number you
want to exchange from.
3
P+
Select the second PROGRAM item using the
+
and buttons.
P -
Use the
and
buttons to select the channel number you
want to exchange to.
+
Select EXCHANGE and press the
activate the exchange command.
or
buttons to
4
5
Press the
button to exit to TV mode.
MENU
NOTE
*1 [EXCHANGE] menu is not available in AV mode.
16
TROUBLESHOOTING
IMPORTANT NOTES
The following problems do not always indicate a hardware failure. Therefore, please use the troubleshooting
guide below before calling for repair service.
If, after following the guide none of the remedies work, unplug the TV set and call for service.
GHOST:
Please change the direction,
height or position of the
NOISE OR INTERFERENCE:
IGNITION NOISE
antenna.
building
White spots and horizontal streaks may appear on
the screen. Usually this is caused by interference
from automobile, neon lamps or other electrical
appliance. So, the antenna should be installed away
from such interference sources.
Reflections
or mountains might
from
cause this phenomenon. A
highly
improve the reception.
directional antenna may
SOUND IS HEARD (BUZZER) BUT NO
PICTURE:
Please check whether the
brightness
control
and
contrast
properly
are
SNOW
Small dots may appear on the
adjusted, and the antenna
is
properly.
connected
into plug
entire screen.
coaxial cable or antenna
installment and
Check the
the direction.
NO PICTURE AND NO SOUND:
Please check that the TV
receiver is plugged in and
that the indicator on
panel of TV
lights is red.
the front
RADIO FREQUENCY INTERFERENCE
The interference produces
moving ripples or diagonal
streaks. This is not caused
by the receiver but is
by interference from other
caused
signals or
radio.
NO COLOUR PICTURE OBTAINABLE
DURING A COLOUR PROGRAM:
Please check that if the input
signal is too weak. Please
check the colour control is
VCR:
When the VCR test signal
(TSG) is received, the
side of the test pattern is
distorted as shown in the
figure.This is not amalfunction
and the playback picture is
not influenced by it.
properly.
tune the frequency with the
adjusted
Please fine
lower
method
of the fine tuning.
For
multi-system models,
check
that the system selected is
colour
correct, including
audio systems.
and
17
Please make these simple checks as
indicated ( ) on the chart for the
respective symptoms and their possible
remedies.
ce
n
trouble
lia
app
ation
et
t
n
s
s
a
f
o
unit
as
colour
rol
g
t
back
robably
in
e)
s
set
such
p
n
e
,
con
n"
o
typ
e
"o
wir
OK
nce,
l
is
if
o
mot
orrectly
ere
roadcast
e
ontrol
c
r
b
indoor
rol
c
control
roken
erf
s
n
t
s
i
if
b
s
i
i
(
contr
n
s
switch
r
ont
i
onnections
ing
e
f
c
o
c
ies
n
channel,
ries
l
l
f
d
/of
tun
erial
ht
ation
t
ystem
a
tte
local
ig
s
s
on
ent
a
eria
eria
eme
ontrast
olour
ine
f
f
f
i
R
a
a
i
i
b
f
br
c
c
t
ient
ffer
i
bably
y
d
ossible
Symptoms
P
T
r
Check
Check
Re-or
Pro
Adjust
Adjus
Adjust
Check
Adjust
Check
Check
Check
No picture, no sound
Poor sound, picture OK
Poor picture, sound OK
Weak picture
Blurred picture
Double image
Lines in picture
Distorted picture
Weak reception on some channels
Horizontal bars
Picture rolls vertically
Poor colour
No colour
Misoperation of Remote control
Remote control unit no operation
On Screen Display Control outside the screen
18
SPECIFICATIONS
Model Name
C29-F880S
C29-F880SN
C29-F880SNT
Screen Size
74 cm (29 inch) diagonal
Please refer to the values as indicated on the
rating label pasted at the back of the TV set.
Power Supply /
Power Consumption
NICAM/A2
No
No
Yes
Yes
Yes*1
Teletext
No
Reception System
Full Multi System
PAL - B/G,D/K , I
SECAM - B/G,D/K , K1
NTSC-M
RF :
VIDEO :
PAL / NTSC / SECAM
NTSC 50
NTSC 4.43
PAL 60
SECAM 60
Frequency Range
Preset Channels
Aerial Input
44.25 - 863.25 MHz
0 - 199
75 Ohm coaxial
8 W + 8 W
Audio Output
TV Dimension (W x D x H)
TV Weight
785 x 495 x 591 mm
44 kg
Specifications may be subject to change without notice for improvement.
NOTE
*1 Teletext function will only operate in countries where Teletext transmission service is available.
If such transmission is unavailable (e.g. in Hong Kong), Teletext function will not operate.
19
20
|