HP Hewlett Packard 2310ei User Manual

2310e and 2310ei LCD Monitors  
User Guide  
About This Guide  
This guide provides information on setting up the monitor, installing drivers, using the on-screen  
display menu, troubleshooting and technical specifications.  
WARNING! Text set off in this manner indicates that failure to follow directions could result in bodily  
harm or loss of life.  
CAUTION: Text set off in this manner indicates that failure to follow directions could result in  
damage to equipment or loss of information.  
NOTE: Text set off in this manner provides important supplemental information.  
ENWW  
iii  
iv  
About This Guide  
ENWW  
Table of contents  
2 Safety and Maintenance Guidelines .............................................................................................................. 3  
3 Setting Up the Monitor ................................................................................................................................... 6  
4 Operating the Monitor .................................................................................................................................. 13  
ENWW  
v
Appendix B Technical Specifications ............................................................................................................ 24  
Appendix C Agency Regulatory Notices ....................................................................................................... 27  
vi  
ENWW  
1 Product Features  
HP 2310e/2310ei LCD Monitors  
Figure 1-1 HP 2310e/2310ei LCD Monitors  
The HP 2310e/2310ei LCD (liquid crystal display) monitors have an active matrix, thin-film transistor  
(TFT) screen with a white LED backlight and the following features:  
Large diagonal display  
Maximum graphics resolution: 1920 x 1080 @ 60Hz, plus full-screen support for lower  
resolutions  
DisplayPort digital input signal  
DVI digital input signal with single-link DVI-D to DVI-D cable provided  
High-definition multimedia interface (HDMI) (2310e model only) signal input  
Fast response time, providing better experience for hardcore gaming and graphics  
Easy viewing from a sitting or standing position, or while moving from one side of the monitor to  
the other  
Dynamic Contrast Ratio to provide deeper blacks and brighter whites for brilliant shading effects  
while gaming or watching movies  
Tilt adjustment  
ENWW  
HP 2310e/2310ei LCD Monitors  
1
   
Swivel adjustment  
Plug and Play capability, if supported by your computer system  
On-screen display (OSD) adjustments for ease of setup and screen optimization (choose  
English, Simplified Chinese, Traditional Chinese, French, German, Italian, Spanish, Dutch,  
Japanese, or Brazilian Portuguese)  
Power Saver to reduce energy consumption  
Quick View settings display  
HDCP (High Bandwidth Digital Content Protection) on DVI, HDMI and DisplayPort inputs  
Software and utilities CD, containing the following:  
Drivers  
Documents  
2
Chapter 1 Product Features  
ENWW  
2 Safety and Maintenance Guidelines  
Important Safety Information  
A power cord is included with the monitor. If another cord is used, use only a power source and  
connection appropriate for this monitor. For information on the correct power cord set to use with the  
monitor, refer to the "Connecting the Power Cord" section in Setting Up the Monitor on page 6.  
WARNING! To reduce the risk of electric shock or damage to the equipment:  
• Do not disable the power cord grounding feature. The grounding plug is an important safety feature.  
• Plug the power cord in a grounded (earthed) outlet that is easily accessible at all times.  
• Disconnect power from the product by unplugging the power cord from the electrical outlet.  
For your safety, do not place anything on power cords or cables. Arrange them so that no one may  
accidentally step on or trip over them. Do not pull on a cord or cable. When unplugging from the  
electrical outlet, grasp the cord by the plug.  
To reduce the risk of serious injury, read the Safety and Comfort Guide. It describes proper  
workstation, setup, posture, and health and work habits for computer users, and provides important  
electrical and mechanical safety information. This guide is located on the Web at http://www.hp.com/  
ergo and/or on the documentation CD, if one is included with the monitor.  
CAUTION: For the protection of the monitor, as well as the computer, connect all power cords for  
the computer and its peripheral devices (such as a monitor, printer, scanner) to some form of surge  
protection device such as a power strip or Uninterruptible Power Supply (UPS). Not all power strips  
provide surge protection; the power strips must be specifically labeled as having this ability. Use a  
power strip whose manufacturer offers a Damage Replacement Policy so you can replace the  
equipment, if surge protection fails.  
Use the appropriate and correctly sized furniture designed to properly support your HP LCD monitor.  
WARNING! LCD monitors that are inappropriately situated on dressers, bookcases, shelves, desks,  
speakers, chests, or carts may fall over and cause personal injury.  
Care should be taken to route all cords and cables connected to the LCD monitor so that they can not  
be pulled, grabbed, or tripped over.  
ENWW  
Important Safety Information  
3
   
Safety Precautions  
Use only a power source and connection compatible with this monitor, as indicated on the label/  
back plate of the monitor.  
Be sure the total ampere rating of the products connected to the outlet does not exceed the  
current rating of the electrical outlet, and the total ampere rating of the products connected to the  
power cord does not exceed the rating of the power cord. Look on the power label to determine  
the ampere rating (Amps or A) for each device.  
Install your monitor near a power outlet that you can easily reach. Disconnect the monitor by  
grasping the plug firmly and pulling it from the outlet. Never disconnect the monitor by pulling the  
cord.  
Do not allow anything to rest on the power cord. Do not walk on the cord.  
Maintenance Guidelines  
To enhance the performance and extend the life of the monitor:  
Do not open the monitor cabinet or attempt to service this product yourself. Adjust only those  
controls that are covered in the operating instructions. If the monitor is not operating properly or  
has been dropped or damaged, contact an authorized HP dealer, reseller, or service provider.  
Use only a power source and connection appropriate for this monitor, as indicated on the label/  
back plate of the monitor.  
Be sure the total ampere rating of the products connected to the outlet does not exceed the  
current rating of the electrical outlet, and the total ampere rating of the products connected to the  
cord does not exceed the rating of the cord. Look on the power label to determine the ampere  
rating (AMP or A) for each device.  
Install the monitor near an outlet that you can easily reach. Disconnect the monitor by grasping  
the plug firmly and pulling it from the outlet. Never disconnect the monitor by pulling the cord.  
Turn the monitor off when not in use. You can substantially increase the life expectancy of the  
monitor by using a screen saver program and turning off the monitor when not in use.  
NOTE: Monitors with a “burned-in image” are not covered under the HP warranty.  
Slots and openings in the cabinet are provided for ventilation. These openings must not be  
blocked or covered. Never push objects of any kind into cabinet slots or other openings.  
Do not drop the monitor or place it on an unstable surface.  
Do not allow anything to rest on the power cord. Do not walk on the cord.  
Keep the monitor in a well-ventilated area, away from excessive light, heat or moisture.  
When removing the monitor base, you must lay the monitor face down on a soft area to prevent  
it from getting scratched, defaced, or broken.  
4
Chapter 2 Safety and Maintenance Guidelines  
ENWW  
   
Cleaning the Monitor  
1. Turn off the monitor and unplug the power cord from the back of the unit.  
2. Dust the monitor by wiping the screen and the cabinet with a soft, clean antistatic cloth.  
3. For more difficult cleaning situations, use a 50/50 mix of water and Isopropyl alcohol.  
CAUTION: Spray the cleaner onto a cloth and use the damp cloth to gently wipe the screen  
surface. Never spray the cleaner directly on the screen surface. It may run behind the bezel and  
damage the electronics.  
CAUTION: Do not use cleaners that contain any petroleum based materials such as benzene,  
thinner, or any volatile substance to clean the monitor screen or cabinet. These chemicals may  
damage the monitor.  
Shipping the Monitor  
Keep the original packing box in a storage area. You may need it later if you move or ship the  
monitor.  
To prepare the monitor for shipping:  
1. Disconnect the power and video cables from the monitor.  
2. Press the button on the front of the pedestal and lift the monitor panel from the base.  
Figure 2-1 Removing the Monitor Panel  
3. Set the panel on a soft, protected surface.  
4. Loosen the screw on the bottom side of the base and remove the pedestal from the base.  
5. Place the monitor, pedestal, and base in the original packing box.  
ENWW  
Maintenance Guidelines  
5
   
3 Setting Up the Monitor  
Unpacking the Monitor  
1. Unpack the monitor. Make sure all contents are included. Store the packing box.  
2. Turn off the computer and other attached devices.  
3. Prepare a flat area to assemble the monitor. You may need a flat, soft, protected area for placing  
the monitor screen-down while preparing it for installation.  
Assembling the Monitor  
Place the monitor in a convenient, well-ventilated location near your computer. Connect the monitor  
cables after you have assembled the monitor.  
NOTE: For displays with glossy bezels, consider the placement of the display as the bezel may  
cause disturbing reflections from surrounding light and bright surfaces.  
1. Set the monitor panel down on a flat, soft, protected table or desk surface.  
CAUTION: The screen is fragile. Avoid touching or applying pressure to the LCD screen; doing  
so can cause damage.  
6
Chapter 3 Setting Up the Monitor  
ENWW  
     
2. Slide the pedestal into the slot on the base (1) and tighten the large screw on the bottom of the  
base (2) to secure the pedestal to the base.  
Figure 3-1 Assembling the Base and Pedestal  
3. Slide the monitor panel's hinge bracket into the opening on top of the pedestal. The panel will  
click into place when fully inserted.  
Figure 3-2 Inserting the Monitor Panel  
ENWW  
Assembling the Monitor  
7
Connecting Monitor Cables  
CAUTION: Before connecting cables to the monitor, ensure that the computer and monitor are  
powered off.  
The video source is determined by the video cable used. The monitor will automatically determine  
which inputs have valid video signals. The inputs can be selected by pressing the source button on  
the front panel.  
Connecting the DVI-D Video Cable  
Connect one end of the DVI-D video cable to the back of the monitor and the other end to the DVI-D  
video connector on the computer. You can use this cable only if your computer has a DVI compliant  
graphics card that is either integrated or installed. The DVI-D cable is included.  
Figure 3-3 Connecting the DVI-D Cable  
8
Chapter 3 Setting Up the Monitor  
ENWW  
   
Connecting the DisplayPort Video Cable  
Connect one end of the DisplayPort Digital Input cable to the back of the monitor and the other end  
connector to the input device. A DisplayPort Digital Input cable is provided on select models only.  
Figure 3-4 Connecting the DisplayPort Cable (cable provided on select models only)  
Connecting the HDMI Cable (2310e Model Only)  
Connect one end of the HDMI cable to the back of the monitor and the other end connector to the  
input device. An HDMI cable is provided on select models only.  
Figure 3-5 Connecting the HDMI Cable (cable provided on select models only)  
ENWW  
Connecting Monitor Cables  
9
   
Connecting the Power Cord  
1. Follow all electrical and power warnings  
WARNING! To reduce the risk of electric shock or damage to your equipment:  
Do not disable the power cord grounding plug. The grounding plug is an important safety  
feature. Plug the power cord into a grounded (earthed) electrical outlet.  
Be sure that the grounded power outlet you plug the power cord into is easily accessible to the  
operator and located as close to the equipment as possible. A power cord should be routed so  
that it is not likely to be walked on or pinched by items that are placed upon it or against it.  
Do not place anything on power cords or cables. Arrange them so that no one may accidentally  
step on or trip over them. Do not pull on a cord or cable.  
See Technical Specifications on page 24 for additional information.  
2. Connect the round end of the power supply cord to the monitor then connect one end of the  
power cord to the power supply and the other end to a grounded electrical outlet.  
WARNING! To prevent injury from electrical shock, you should do one of the following if a  
properly grounded electrical outlet is not available: (1) You should use an electrical outlet  
adapter that provides proper grounding. (2) You should have a properly grounded electrical  
outlet installed.  
Figure 3-6 Connecting the Power Cord  
High-Bandwidth Digital Content Protection (HDCP)  
Your monitor supports HDCP and can receive high-definition content. High-definition content is  
available in many sources, such as Blu-ray Disc devices or HDTV air or cable broadcasts. If you do  
not have an HDCP-enabled monitor, you will see a blank screen or a lower resolution picture when  
playing high-definition protected content. Your computer graphics card and monitor must both support  
HDCP to display protected content.  
10 Chapter 3 Setting Up the Monitor  
ENWW  
   
Turning on the Monitor  
1. Press the power button on the computer to turn it on.  
2. Press the power button on the front of the monitor to turn it on.  
CAUTION: Burn-in image damage may occur on monitors that display the same static image on  
screen for a prolonged period of time.* To avoid burn-in image damage on the monitor screen, you  
should always activate a screen saver application or turn off the monitor when it is not in use for a  
prolonged period of time. Image retention is a condition that may occur on all LCD screens. Monitors  
with a “burned-in image” are not covered under HP warranty.  
* A prolonged period of time is 12 consecutive hours of non-use.  
When the monitor is powered on, a Monitor Status message is displayed for five seconds. The  
message shows which input is the current active signal, the status of the auto-switch source setting  
(On or Off), the default source signal, the current preset display resolution, and the recommended  
preset display resolution.  
Selecting Video Input Connectors  
The input connectors are:  
DisplayPort (digital)  
DVI-D connector (digital)  
HDMI connector (digital) 2310e model  
The monitor automatically scans the signal inputs for an active input and uses that input for the  
display. If two inputs are active, the monitor will display the default input source. If the default source  
is not an active input, then the monitor will display the other input if it is active. You can change the  
default source in the OSD by pressing the front panel Menu button and selecting Source Control >  
Default Source.  
Adjusting The Tilt  
For optimal viewing, adjust the screen tilt to your own preference, as follows:  
1. Face the front of the monitor and hold the base so that you do not topple the monitor while  
changing the tilt.  
ENWW  
Turning on the Monitor 11  
     
2. Adjust the tilt by moving the top edge of the monitor either toward or away from you, without  
touching the screen.  
Figure 3-7 Tilt Adjustment  
Adjusting the Swivel  
The monitor allows a usable range of motion with the swivel feature.  
Figure 3-8 Swivel Adjustment  
CAUTION: To avoid breakage or other damage, avoid applying pressure to the LCD screen while  
swiveling it or changing the tilt.  
12 Chapter 3 Setting Up the Monitor  
ENWW  
 
4 Operating the Monitor  
CD Software and Utilities  
The CD that is included with this monitor contains drivers and software that you can install on your  
computer.  
Installing Drivers  
If you determine that you need to update the drivers, you can install the monitor driver INF and ICM  
files from the CD, or download them from the Internet.  
Installing the monitor driver software from the CD  
To install the monitor driver software from the CD:  
1. Insert the CD in your computer CD drive. The CD menu appears.  
2. Select the language.  
3. Click Install Monitor Driver Software.  
4. Follow the on-screen instructions.  
5. Ensure that the proper resolutions and refresh rates appear in the Display Control Panel  
settings. Refer to the Windows® operating system documentation for more information.  
NOTE: You might need to install the digitally signed monitor drivers (INF or ICM files) manually  
from the CD, in case of an installation error. Refer to the "Driver Software Readme" file on the  
CD for instructions (in English only).  
Downloading updated drivers from the Internet  
To download the latest version of drivers and software files from the HP Support site:  
1. Refer to: http://www.hp.com/support.  
2. Select your country/region.  
3. Select Download Drivers and Software.  
4. Enter the model number of your monitor. The software download pages for your monitor are  
displayed.  
5. Download and install the driver and software files by following the instructions on the download  
pages.  
6. Ensure that your system meets the requirements.  
ENWW  
CD Software and Utilities 13  
     
Front-Panel Controls  
Control buttons are located on the bottom right of the monitor. The buttons are represented by icons  
that become illuminated when the bar area on the front panel is touched.  
Button  
Icon  
Description  
Source  
Chooses the video input source from the computer.  
Quick View  
Opens the OSD Quick View menu where you can select a viewing mode.  
Minus  
Plus  
Navigates down through the OSD menu and decreases adjustment levels.  
Navigates up through the OSD menu and increases adjustment levels.  
Enters the selected option in the OSD.  
OK  
Menu  
Opens, selects, or exits the OSD menu.  
NOTE: Pressing the Menu button for 10 seconds will disable operation of the  
remaining OSD buttons. Pressing it again for 10 seconds will re-enable  
functionality.  
Power  
Turns the monitor on or puts it in standby or sleep mode. The Power button is  
located on the bottom-right of the monitor.  
NOTE: Pressing the Power button for 10 seconds will disable operation of  
the Power button. Pressing it again for 10 seconds will re-enable functionality.  
NOTE: The slider bars on the front panel between the Plus (+) and Minus (–) buttons can also be  
used for navigating menu items and making OSD control adjustments.  
14 Chapter 4 Operating the Monitor  
ENWW  
 
Using the On-Screen Display (OSD)  
Use the On-Screen Display (OSD) to adjust the screen image based on your viewing preferences. To  
access the OSD, do the following:  
1. If the monitor is not already on, press the Power button to turn on the monitor.  
2. To access the OSD menu, press the Menu button. The OSD Main Menu displays.  
NOTE: You need to touch the bar area on the front panel to display the front panel button  
icons.  
3. To navigate through the Main or sub-menu, press the + (Plus) button on the monitor's front panel  
to scroll up, or the (Minus) button to scroll in reverse. Then press the OK button to select the  
highlighted function.  
NOTE: The menu moves to the top if you scroll down at the bottom of the selections. The  
menu moves to the bottom if you scroll up at the top of the selections.  
NOTE: The slider bars on the front panel between the Plus (+) and Minus (–) buttons can also  
be used for navigating menu items and making OSD control adjustments.  
4. To adjust the scale of a selected item, press the + or – button, or use the slider bar.  
5. Select Save and Return. If you don't want to save the setting, select Cancel from the sub-menu  
or Exit from the Main Menu.  
6. Press the Menu button to exit the OSD.  
NOTE: When a menu is displayed, if the buttons are untouched for 30 seconds (factory  
default), adjustments and settings are saved and the menu closes.  
OSD Menu Selections  
The following table lists the on-screen display (OSD) menu selections and their functional  
descriptions. After changing an OSD menu item, and if the menu screen has these options, you may  
choose to:  
Cancel — to return to the previous menu level.  
Save and Return — to save all changes and return to the OSD Main Menu screen. This Save  
and Return option is active only if you change a menu item.  
Reset — to change back to the previous setting.  
Icon  
Main Menu Options  
Sub-menu Options  
Description  
Brightness  
Adjusts the brightness level of the  
screen.  
Contrast  
Color  
Adjusts the contrast level of the screen.  
Selects the screen color. The factory  
default is 6500 K or Custom Color,  
depending on the model.  
6500 K  
9300 K  
Changes to slightly reddish white.  
Changes to slightly blueish white.  
ENWW  
Using the On-Screen Display (OSD) 15  
 
Icon  
Main Menu Options  
Sub-menu Options  
Description  
sRGB  
Sets your screen colors to adapt to the  
color standards used in the image  
technology industry.  
Quick View  
Select from the following modes:  
Movie  
Photo  
Gaming  
Text  
Custom (settings saved when you adjust  
the Brightness, Contrast, or Color in one  
of the other Quick View options)  
Custom Color  
Selects and adjusts your own color  
scales:  
R — Sets your own red color levels.  
G — Sets your own green color levels.  
B — Sets your own blue color levels.  
Image Control  
Adjusts the screen image. Also enables  
or disables the ambient light sensor.  
Custom Scaling  
Selects the method on how displayed  
information on the monitor will be  
formatted. Select:  
Fill to Screen - image fills the entire  
screen and may look distorted or  
elongated because of non-  
proportional scaling of height and  
width.  
Fill to Aspect Ratio - image is sized  
to fit the screen and maintains  
proportional image.  
Sharpness  
Adjusts the screen image to look  
sharper or soft.  
Dynamic Contrast Ratio  
Sets the Dynamic Contrast Ratio (DCR)  
setting on or off. The factory default  
setting is off. DCR automatically adjusts  
the balance between white and black  
levels to provide you with an optimal  
image.  
OSD Control  
Adjusts the position of the OSD menu  
on the screen.  
Horizontal OSD Position  
Vertical OSD Position  
Changes the viewing position of the  
OSD menu to the left or right area of the  
screen. The factory default range is 94.  
Changes the viewing position of the  
OSD menu to the top or bottom area of  
the screen. The factory default range is  
17.  
16 Chapter 4 Operating the Monitor  
ENWW  
Icon  
Main Menu Options  
Sub-menu Options  
Description  
OSD Transparency  
Adjust to view the background  
information through the OSD.  
OSD Timeout  
Power Saver  
Sets the time in seconds that the OSD is  
visible after the last button is pressed.  
The factory default is 30 seconds.  
Management  
Selects the power-management features  
of the monitor.  
Enables the power saving feature (see  
Select:  
On  
Off  
The factory default is On.  
Power-On Recall  
Restores power to the monitor following  
an unexpected removal of power.  
Select:  
On  
Off  
The factory default is On.  
Mode Display  
Displays the resolution, refresh rate, and  
frequency information on the screen  
each time the OSD Main Menu is  
accessed. Select:  
On  
Off  
The factory default is On.  
Monitor Status  
Displays the operating status of the  
monitor each time the monitor is  
powered on. Select the location at which  
to display the status:  
Top  
Middle  
Bottom  
Off  
The factory default is Top.  
ENWW  
Using the On-Screen Display (OSD) 17  
Icon  
Main Menu Options  
Sub-menu Options  
Description  
DDC/CI Support  
Allows the computer to control some  
OSD menu features such as Brightness,  
Contrast, and Color Temperature.  
Select:  
On  
Off  
The factory default is On.  
Bezel Power LED  
Rear Logo LED  
Sleep Timer  
Turns the light (LED) in the Power  
button on and off. When set to off, the  
light will remain off at all times.  
Turns the light (LED) on the rear logo on  
and off. When set to off, the light will  
remain off at all times.  
Provides the timer-adjustment menu  
options:  
Set Current Time — Sets the current  
time in hours and minutes.  
Set Sleep Time — Sets the time you  
want to place the monitor in sleep mode.  
Set On Time — Sets the time you want  
the monitor to wake up from sleep  
mode.  
Timer — Sets the Sleep Timer feature  
on or off; the default setting is Off.  
Sleep Now — Immediately sets the  
monitor to enter sleep mode.  
Language  
Selects the language in which the OSD  
menu is displayed. The factory default is  
English.  
Information  
Selects and displays important  
information about the monitor.  
Current Settings  
Provides the current input video mode.  
Recommended Settings  
Provides the recommended resolution  
mode and refresh rate for the monitor.  
Serial Number  
Reports the serial number of the  
monitor. The serial number is needed if  
contacting HP technical support.  
FW Version  
Reports the firmware version of the  
monitor.  
Backlight Hours  
Service Support  
Reports the total hours of backlight  
operation.  
For service support, go to:  
Factory Reset  
Returns settings to factory defaults.  
18 Chapter 4 Operating the Monitor  
ENWW  
Icon  
Main Menu Options  
Sub-menu Options  
Description  
Source Control  
Selects the video input signal. the  
factory default by priority is DisplayPort,  
DVI, then HDMI.  
DVI  
Selects DVI as the video input signal.  
Selects HDMI as the video input signal.  
HDMI (2310e model)  
DisplayPort  
Selects DisplayPort as the video input  
signal.  
Default Source  
Selects the default or primary video  
input signal when the monitor is  
connected to two active and valid video  
sources. The monitor will automatically  
determine the video format.  
Auto Switch Source  
Source Detection  
Turns the system's automatic video  
signal input to On or Off. The factory  
default is On.  
This option is displayed in the OSD  
when a DisplayPort input is selected.  
You can set Source Detection to:  
Always Active  
Low Power  
The factory default is Low Power.  
Exits the OSD menu screen.  
Exit  
Identifying Monitor Conditions  
Special messages appear on the monitor screen for the following monitor conditions:  
Monitor Status—When the monitor is powered on or when the input source signal is changed, a  
Monitor Status message is displayed for five seconds. The message shows which input is the  
current active signal, the status of the auto-switch source setting (On or Off), the default source  
signal, the current preset display resolution, and the recommended preset display resolution.  
Input Signal Out of Range — Indicates the monitor does not support the video card's input  
signal because its resolution or refresh rate are set higher than the monitor supports.  
Change your video card settings to a lower resolution or refresh rate. Restart your computer for  
the new settings to take effect.  
Power Button Lockout— Indicates the power button is locked. If the power button is locked,  
the warning message Power Button Lockout displays.  
If the power button is locked, press and hold the power button for 10 seconds to unlock the  
power button function.  
If the power button is unlocked, press and hold the power button for 10 seconds to lock out the  
power button function.  
Monitor Going to Sleep — Indicates the screen display is entering a sleep mode.  
ENWW  
Identifying Monitor Conditions 19  
 
Check Video Cable — Indicates a video input cable is not properly connected to the computer  
or monitor.  
OSD Lockout — The OSD can be enabled or disabled by pressing and holding the Menu button  
on the front panel for 10 seconds. If the OSD is locked, the warning message OSD Lockout  
appears for 10 seconds.  
If the OSD is locked, press and hold the Menu button for 10 seconds to unlock the OSD.  
If the OSD is unlocked, press and hold the Menu button for 10 seconds to lock the OSD.  
Dynamic Contrast Ratio ON – Indicates that DCR is turned on.  
Dynamic Contrast Ratio OFF – Indicates that DCR has been turned off in the OSD or was  
automatically turned off after changes were made to Brightness, Contrast, or Quick View in the  
OSD.  
No Input Signal — Indicates the monitor is not receiving a video signal from the computer on  
the monitor video input connector. Check to see if the computer or input signal source is off or in  
the power-saver mode.  
Power-Saver Feature  
When the monitor is in normal operating mode, the Power light is blue and the monitor uses the  
normal watts of power. For power usage, refer to Technical Specifications on page 24.  
The monitor also supports a power-saver mode that is controlled by the computer. When the monitor  
is in the reduced-power state, the monitor screen is blank, the backlight is off, the Power light is  
amber, and the monitor uses minimum power. When the monitor is "awakened," a brief warm-up  
period occurs before the monitor returns to normal operating mode. The energy-saving reduced  
power state activates if the monitor does not detect either the horizontal sync signal or the vertical  
sync signal. The power-saver feature must be activated on your computer for this feature to work.  
Refer to your computer documentation for instructions on setting energy-saver features (sometimes  
called power-management features).  
NOTE: The energy-saver feature works only when the monitor is connected to computers that have  
energy-saver features.  
20 Chapter 4 Operating the Monitor  
ENWW  
 
A Troubleshooting  
Solving Common Problems  
The following table lists possible problems, the possible cause of each problem, and the  
recommended solutions:  
Problem  
Solution  
Power LED is not on.  
Make sure the Power button is on, and the power cord is properly connected to a grounded  
power outlet and to the monitor.  
Select Management in the OSD menu, and then select Bezel Power LED. Check if the  
Bezel Power LED option is set to Off and, if so, set to On mode.  
Screen is blank.  
Connect the power cord. Turn on the power.  
Connect the video cable properly. See Setting Up the Monitor on page 6 for more  
information.  
Press a key on the keyboard or move the mouse to turn off the screen-blanking utility.  
Image appears blurred,  
indistinct, or too dark.  
Press the Menu button to open the OSD menu, and adjust the brightness and contrast  
scales.  
Check Video Cable appears  
on screen.  
Connect the appropriate video cable (DisplayPort, DVI, or HDMI) between the computer and  
monitor. Be sure that the computer power is off while connecting the video cable.  
Input Signal Out of Range  
appears on screen.  
Restart your computer and enter Safe Mode. Change your settings to a supported setting  
(see the table in Preset Video Modes on page 25). Restart your computer so that the new  
settings take effect.  
Picture is fuzzy and has  
ghosting, shadowing  
problem.  
Adjust the contrast and brightness controls.  
Make sure that you are not using an extension cable or switch box. HP recommends  
plugging the monitor directly into the graphic card output connector on the back of your  
computer.  
Unable to set the monitor to  
the optimal resolution.  
Make sure the graphics card supports the optimal resolution.  
Make sure the latest supported driver is installed for the graphics card. For HP and Compaq  
systems, you can download the latest graphics driver for your system from:  
http://www.hp.com/support. For other systems, refer to the Web site for your graphics card.  
Screen is black or displaying Check if your monitor and computer support HDCP. Refer to High-Bandwidth Digital Content  
at a lower resolution while  
displaying high-definition  
(HD) content.  
ENWW  
Solving Common Problems 21  
   
Problem  
Solution  
No Plug and Play.  
In order for the Plug and Play feature of the monitor to work, you need a computer and  
graphic card that are compatible with Plug and Play. Check with your computer  
manufacturer.  
Check the monitor's video cable, and make sure that none of the pins are bent.  
Make sure that the monitor drivers are installed. Refer to Installing Drivers on page 13 for  
more information. Monitor drivers are also available at: http://www.hp.com/support.  
Picture bounces, flickers, or  
wave pattern is present in  
the picture.  
Move electrical devices that may cause electrical interference as far away from the monitor  
as possible.  
Use the maximum refresh rate that your monitor is capable of at the resolution that you are  
using.  
Using HDMI connection,  
unable to hear audio.  
The monitor does not provide an audio solution. The audio stream must be connected  
directly to external speakers or to an audio receiver.  
Monitor is always in sleep  
mode (amber LED).  
Power to the computer should be turned on.  
The computer graphic card should be snugly seated in its slot.  
Check that the monitor video cable is properly connected to the computer.  
Inspect the monitor video cable, and make sure that none of the pins are bent.  
Check that your computer is operational: Press the Caps Lock key and observe the Caps  
Lock LED found on most keyboards. The LED should either turn on or off after hitting the  
Caps Lock key.  
Getting Support from hp.com  
Before you contact customer service, refer to HP Technical Support at: http://www.hp.com/support  
Select your country/region, and then follow the links to the support page for your monitor.  
Preparing to Call Technical Support  
If you cannot solve a problem by using the troubleshooting tips in this section, you might have to call  
technical support. For technical support contact information, refer to the printed documentation  
included with the monitor.  
Have the following information available when you call:  
Monitor model number (located on label on back of monitor)  
Monitor serial number (located on label on back of monitor or in the OSD display in the  
Information menu)  
Purchase date on invoice  
Conditions under which the problem occurred  
Error messages received  
Hardware configuration  
Name and version of hardware and software you are using  
22 Appendix A Troubleshooting  
ENWW  
   
Locating the Rating Label  
The rating label on the monitor provides the product number and serial number. You may need these  
numbers when contacting HP about your monitor model.  
The rating label is on the back of the monitor.  
ENWW  
Locating the Rating Label 23  
 
B Technical Specifications  
All specifications represent the typical specifications provided by HP's component manufacturers;  
actual performance may vary either higher or lower.  
HP LCD Monitors  
Table B-1 2310e/2310ei Specifications  
Specifications  
Display Type:  
TFT LCD active matrix  
58.42 cm (23.0 in.) diagonal  
2310ei: DisplayPort, DVI; 2310e: DisplayPort, DVI, HDMI  
-5° to +25°  
Viewable Image Size:  
Video Input Terminals:  
Tilt:  
Maximum Weight (unpacked):  
Dimensions (h x w x d):  
Maximum Graphics Resolution:  
Optimum Graphics Resolution:  
Text Mode:  
4.3 kg (9.5 lb)  
415.9 x 557.9 x 148.5 mm (16.37 x 21.96 x 5.85 in.)  
1920 x 1080 @ 60 Hz  
1920 x 1080 @ 60 Hz  
720 x 400  
Pixel Pitch:  
0.265 x 0.265 mm  
Horizontal Frequency:  
Vertical Frequency:  
24 to 94 kHz  
50 to 76 Hz  
Operating Temperature:  
Non-Operating Humidity:  
Operating Humidity:  
Non-Operating Humidity:  
Operating Altitude:  
5° to 35° C (41° to 95° F)  
-20° to 60° C (-4° to 140° F)  
20% to 80%  
5% to 95%  
0 to 3,658 meters (0 to 12,000 feet)  
0 to 12,192 meters (0 to 40,000 feet)  
100–240 VAC (ca), 50/60 Hz  
28 watts (W)  
Storage Altitude:  
Power Source:  
Maximum Power Consumption:  
Typical Power Consumption:  
Sleep Power Consumption:  
22 watts (W)  
<2 watts (W)  
24 Appendix B Technical Specifications  
ENWW  
   
Preset Video Modes  
The monitor automatically recognizes many preset video input modes that will appear properly sized  
and centered on the screen.  
Table B-2 Factory Preset Video Input Modes  
Preset  
Resolution  
640 x 480  
Horizontal Frequency (kHz)  
Vertical Frequency (Hz)  
1
31.469  
31.469  
37.879  
48.363  
45.00  
60.00  
63.98  
55.94  
75.00  
65.29  
67.50  
59.94  
70.087  
60.317  
60.004  
60.00  
60.00  
60.02  
59.89  
60.00  
60.00  
60.00  
2
720 x 400  
3
800 x 600  
4
1024 x 768  
1280 x 720  
1280 x 960  
1280 x 1024  
1440 x 900  
1600 x 1200  
1680 x 1050  
1920 x 1080  
5
6
7
8
9
10  
11  
Table B-3 HDMI High Definition Factory Preset Video Modes (2310e Model Only)  
Preset  
HD Video Display  
Resolution  
Resolution  
Horizontal Frequency  
(kHz)  
Vertical Frequency  
(Hz)  
1
2
3
4
5
6
480p  
720 x 480  
31.469  
45  
60  
60  
50  
50  
60  
50  
720p60  
576p  
1280 x 720  
720 x 576  
31.25  
37.5  
720p50  
1080p60  
1080p50  
1280 x 720  
1920 x 1080  
1920 x 1080  
67.5  
56.25  
Entering User Modes  
The video controller signal may occasionally call for a mode that is not preset if:  
You are not using a standard graphics adapter.  
You are not using a preset mode.  
It this occurs, you may need to readjust the parameters of the monitor screen by using the on-screen  
display. Your changes can be made to any or all of these modes and saved in memory. The monitor  
automatically stores the new setting, then recognizes the new mode just as it does a preset mode. In  
addition to the factory preset modes, there are at least ten user modes that can be entered and  
stored.  
ENWW  
Preset Video Modes 25  
   
LCD Monitor Quality and Pixel Policy  
Your LCD Monitor uses high-precision technology, manufactured according to high standards, to help  
guarantee trouble-free performance. Nevertheless, the display may have cosmetic imperfections that  
appear as small bright or dark spots. This is common to all LCD displays used in products supplied by  
all vendors and is not specific to your LCD Monitor. These imperfections are caused by one or more  
defective pixels or subpixels.  
A pixel consists of one red, one green, and one blue subpixel. A defective whole pixel is always  
turned on (a bright spot on a dark background), or it is always off (a dark spot on a bright  
background). The first is the more visible of the two. A defective subpixel (dot defect) is less visible  
than a defective whole pixel, and is small and only visible on a specific background.  
To locate defective pixels, the monitor should be viewed under normal operating conditions and in  
normal operating mode at a supported resolution and refresh rate, from a distance of approximately  
50 cm (16 inches). We expect that, over time, the industry will continue to improve its ability to  
produce displays with fewer cosmetic imperfections, and we will adjust guidelines as improvements  
are made.  
For more information about your LCD Monitor and pixel policy, refer to the HP Web site at:  
http://www.hp.com/support. To find pixel policy information on the HP Web site, type in "HP Pixel  
Policy" in the search box and press Enter.  
26 Appendix B Technical Specifications  
ENWW  
 
C Agency Regulatory Notices  
Federal Communications Commission Notice  
This equipment has been tested and found to comply with the limits for a Class B digital device,  
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection  
against harmful interference in a residential installation. This equipment generates, uses, and can  
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may  
cause harmful interference to radio communications. However, there is no guarantee that interference  
will not occur in a particular installation. If this equipment does cause harmful interference to radio or  
television reception, which can be determined by turning the equipment off and on, the user is  
encouraged to try to correct the interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and the receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is  
connected.  
Consult the dealer or an experienced radio or television technician for help.  
Modifications  
The FCC requires the user to be notified that any changes or modifications made to this device that  
are not expressly approved by Hewlett Packard Company may void the user's authority to operate the  
equipment.  
Cables  
Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods  
to maintain compliance with FCC Rules and Regulations.  
Declaration of Conformity for Products Marked with the  
FCC Logo (United States Only)  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two  
conditions:  
1. This device may not cause harmful interference.  
2. This device must accept any interference received, including interference that may cause  
undesired operation.  
For questions regarding the product, contact:  
ENWW  
Federal Communications Commission Notice 27  
         
Hewlett Packard Company  
P. O. Box 692000, Mail Stop 530113  
Houston, Texas 77269-2000  
Or, call 1-800-HP-INVENT (1-800 474-6836)  
For questions regarding this FCC declaration, contact:  
Hewlett Packard Company  
P. O. Box 692000, Mail Stop 510101  
Houston, Texas 77269-2000  
Or, call (281) 514-3333  
To identify this product, refer to the Part, Series, or Model number found on the product.  
Canadian Notice  
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing  
Equipment Regulations.  
Avis Canadien  
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel  
brouilleur du Canada.  
European Union Regulatory Notice  
Products bearing the CE marking comply with the following EU Directives:  
Low Voltage Directive 2006/95/EC  
EMC Directive 2004/108/EC  
Ecodesign Directive 2009/125/EC, where applicable  
CE compliance of this product is valid if powered with the correct CE-marked AC adapter provided by  
HP.  
Compliance with these directives implies conformity to applicable harmonized European standards  
(European Norms) that are listed in the EU Declaration of Conformity issued by HP for this product or  
product family and available (in English only) either within the product documentation or at the  
following web site: http://www.hp.eu/certificates (type the product number in the search field).  
The compliance is indicated by one of the following conformity markings placed on the product:  
28 Appendix C Agency Regulatory Notices  
ENWW  
     
For non-telecommunications products and for EU  
harmonized telecommunications products, such  
as Bluetooth® within power class below 10mW.  
For EU non-harmonized telecommunications  
products (If applicable, a 4-digit notified body  
number is inserted between CE and !).  
Please refer to the regulatory label provided on the product.  
The point of contact for regulatory matters is: Hewlett-Packard GmbH, Dept./MS: HQ-TRE,  
Herrenberger Strasse 140, 71034 Boeblingen, GERMANY.  
German Ergonomics Notice  
HP products which bear the "GS" approval mark, when forming part of a system comprising HP brand  
computers, keyboards and monitors that bear the "GS" approval mark, meet the applicable  
ergonomic requirements. The installation guides included with the products provide configuration  
information.  
Japanese Notice  
Korean Notice  
Power Cord Set Requirements  
The monitor power supply is provided with Automatic Line Switching (ALS). This feature allows the  
monitor to operate on input voltages between 100–120V or 200–240V.  
The power cord set (flexible cord or wall plug) received with the monitor meets the requirements for  
use in the country where you purchased the equipment.  
If you need to obtain a power cord for a different country, you should purchase a power cord that is  
approved for use in that country.  
The power cord must be rated for the product and for the voltage and current marked on the product's  
electrical ratings label. The voltage and current rating of the cord should be greater than the voltage  
ENWW  
German Ergonomics Notice 29  
       
and current rating marked on the product. In addition, the cross-sectional area of the wire must be a  
minimum of 0.75 mm² or 18 AWG, and the length of the cord must be between 6 feet (1.8 m) and 12  
feet (3.6 m). If you have questions about the type of power cord to use, contact an authorized HP  
service provider.  
A power cord should be routed so that it is not likely to be walked on or pinched by items placed upon  
it or against it. Particular attention should be paid to the plug, electrical outlet, and the point where the  
cord exits from the product.  
Japanese Power Cord Requirements  
For use in Japan, use only the power cord received with this product.  
CAUTION: Do not use the power cord received with this product on any other products.  
Product Environmental Notices  
ENERGY STAR® Qualification  
HP Displays marked with the ENERGY STAR® certification mark meet the requirements of the U.S.  
Environmental Protection Agency (EPA) ENERGY STAR program. The EPA ENERGY STAR®  
certification mark does not imply endorsement by the EPA. As an ENERGY STAR Partner, Hewlett  
Packard Company has determined that this product meets the ENERGY STAR® program  
requirements for display energy efficiency.  
The following ENERGY STAR® certification mark appears on all ENERGY STAR qualified displays:  
The ENERGY STAR® program specifications for displays and computers were created by the EPA to  
promote energy efficiency and reduce air pollution through more energy-efficient equipment in  
homes, offices, and factories. One way products achieve this goal is by using the Microsoft Windows  
power management feature to reduce power consumption when the product is not in use.  
The power management feature enables the computer to initiate a low-power or “sleep” mode after a  
period of user inactivity. When used with an external ENERGY STAR® qualified display, this feature  
also supports similar power management features for the display. To take advantage of these  
potential energy savings, users should use the default power management settings that are provided  
with ENERGY STAR qualified computers and displays. The default power management settings on  
ENERGY STAR qualified computers are preset to behave in the following ways when the system is  
operating on AC power:  
Turn off an external display after 15 minutes of user inactivity  
Initiate a low power sleep mode for the computer after 30 minutes of user inactivity  
ENERGY STAR® qualified computers exit the low power sleep mode and ENERGY STAR qualified  
displays resume operation when the user resumes use of the computer. Examples include the user  
30 Appendix C Agency Regulatory Notices  
ENWW  
     
pressing the power/sleep button, receiving an input signal from an input device, receiving an input  
signal from a network connection with the Wake On LAN (WOL) feature enabled, etc.  
Additional information on the ENERGY STAR® program, its environmental benefits and the potential  
energy and financial savings of the power management feature can be found on the EPA ENERGY  
STAR Power Management Web site at http://www.energystar.gov/powermanagement.  
Disposal of Waste Equipment by Users in Private Household in the  
European Union  
This symbol on the product or on its packaging indicates that this product must not be disposed of  
with your household waste. Instead, it is your responsibility to dispose of your waste equipment by  
handing it over to a designated collection point for the recycling or waste electrical and electronic  
equipment. The separate collection and recycling of your waste equipment at the time of disposal will  
help to conserve natural resources and ensure that it is recycled in a manner that protects human  
health and the environment. For more information about where you can drop off your waste  
equipment for recycling, please contact the local city office, the household waste disposal service or  
the shop where you purchased the product.  
Chemical Substances  
HP is committed to providing our customers with information about the chemical substances in our  
products as needed to comply with legal requirements such as REACH (Regulation EC No  
1907/2006 of the European Parliament and Council). A chemical information report for this product  
can be found at http://www.hp.com/go/reach.  
HP Recycling Program  
HP encourages customers to recycle used electronic hardware, HP original print cartridges, and  
rechargeable batteries. For more information about recycling programs, go to http://www.hp.com/  
Restriction of Hazardous Substances (RoHS)  
A Japanese regulatory requirement, defined by specification JIS C 0950, 2005, mandates that  
manufacturers provide Material Content Declarations for certain categories of electronic products  
offered for sale after July 1, 2006. To view the JIS C 0950 material declaration for this product, visit  
ENWW  
Product Environmental Notices 31  
       
11363-2006  
11363-2006  
Turkey EEE Regulation  
In Conformity with the EEE Regulation  
EEE Yönetmeliğine Uygundur  
32 Appendix C Agency Regulatory Notices  
ENWW  
 

Frigidaire 318200626 User Manual
Fostex PD 6 User Manual
Electrolux 5995447090E36GC76EPS User Manual
Diamond Multimedia ATI Radeon X1650 Pro PCIE User Manual
DCS CP 484GG User Manual
Bosch Appliances Cooktop PGP976SET User Manual
A T International TL32350 User Manual
Asus LCD Monitor VW246H User Manual
AOC 2019Vwa1 User Manual
Ameriphone Plantronics Corded Headset P 300 User Manual