User’s Guide
Cordless Phone
230i
HANDSET
Antenna
Warning light
Earpiece
Volume up key
Volume down key
Display
Off hook key
Scroll up key
On Hook/On/Off key
Clear/Mute key
Scroll down key
Number keys
Battery compartment
(on the back)
Internal call key
R key
Microphone
Charge contacts
BASE STATION
Page button
External line/
subscription
mode light
Handset
compartment
Desk stand
(on the back)
Cable
connections
(on the back)
Charging light
glance
Getting started 5
Preparing for use 5
A brief guide 7
Using the menus 8
Battery 9
Attaching and removing the clip 10
Basic use and settings 11
Telephoning 11
Phone book 14
Advanced telephoning 16
Personalising the handset 19
Personalising the base station 20
PIN codes and blocking handset keys 22
Extra features 25
Baby monitor 25
Direct call 25
Cost manager 26
Voice mail notification 27
Connecting handsets to base stations 28
Reference 31
Safety instructions 31
Troubleshooting 31
Buttons, keys, icons and signals 34
Menus 36
Maintenance 38
Warranty 38
Index 40
This user’s guide is published by
Ericsson Business Mobile Networks BV,
wihout any warranty. Improvements and
changes to this user’s guide necessi-
tated by typographical errors, inaccura-
cies of current information, or changes
to programs and/or equipment, may be
made by Ericsson Business Mobile Net-
works BV at any time and without notice.
Such changes will, however, be incorpo-
rated into new editions of this user’s
guide. All rights reserved.
Standards and regulations
•
The base station BS230i complies with: RTTE directive 99/5/EC, EMC directive 89/336/EC,
LVD directive 73/23/EC.
•
The DT200 handset complies with: TTE directive 91/263/EC, EMC directive 89/336/EC,
LVD directive 73/23/EC.
Environmental policy
Ericsson will contribute to the sustainable development of global society by developing, produc-
ing and offering low environmental impact products and services that also allows customers to
reduce their environmental impact. This means that we shall:
•
•
•
Increase knowledge and consciousness about environmental issues among all employees to a
level where it becomes a natural and pro-active part of the everyday decision-making process.
Base our environmental knowledge on scientific grounds and use life cycle assessment tech-
niques as a guide and a basis for communicating environmental issues.
Introduce and maintain certifiable environmental management systems within all organiza-
tions that have any significant influence on the environmental impact from processes, prod-
ucts or services.
•
Meet or exceed legal requirements to protect the environment and use designing for the envi-
ronment as a means to introduce environmentally improved processes, products and services.
Involve suppliers in our on-going work to improve environmental performance.
Where appropriate support and participate in environmental research relating to our field of
interest and actively participate in international harmonization of environmental
standardization.
•
•
Getting started
PREPARING FOR USE
About ISDN
This cordless phone is suitable for use with Euro-ISDN. ISDN, which stands
for Integrated Services Digital Network, integrates the simultaneous transmis-
sion of speech and data. With Euro-ISDN you have access to two digital tele-
phone lines. This makes it possible, for example, to have two telephone
conversations at the same time or to have an ISDN internet connection with
your computer on one line and still be able to make and receive telephone
calls on the other line.
ISDN comes with several telephone numbers (network operator and subscrip-
tion dependent), making it possible to reserve a phone number for instance for
business calls and another number for private phone calls (see “Multiple Sub-
scriber Numbers (MSN)” on page 20 for more information). The ISDN serv-
ices described in this manual are operator and subscription dependent.
Installation
You can install the cordless phone directly to the ISDN network terminal,
which may also have other devices attached, such as an ISDN modem or a fax
machine.
Warning Make sure the local mains voltage corresponds to the voltage on the
power adaptor. Only use the power adaptor that comes with the set.
When installing the cordless phone, it is important that you closely follow
the procedure below:
1. Insert the battery in the handset.
2. Find a suitable location for the base station. To make the best use of its
operating range, put your base station in a central position. You can place
it on a table using the desk stand or mount it on the wall using the wall
Getting started
5
mount. Due to possible interference, do not place the cordless phone near
audio or video equipment.
3. If you place the base station on a wall, screw the wall mount to the wall.
4. Connect the telephone cable to the base station’s telephone socket and to
the ISDN network terminator. Connect the power cord to the power plug
socket of the base station.
Line
Power
5. Connect the desk stand to the base station or connect the base station to the
wall mount. Locate the lower hooks first.
For the desk stand, route the cables through the slots at the back.
6. Place the handset into the base station as shown in the illustration. Make
sure that the handset is switched off.
7. Plug the power adaptor into the wall socket.
The red light on top of the base station should now be on continuously. If
you see a red, flashing light, there is a fault with the telephone line
connection.
the red light on the top of the base station will go off.
8. Leave the handset in the base station for at least 3 hours to charge the bat-
tery for the first time.
Home
1
When the battery is charged, the handset is ready for use. For more informa-
tion about charging the battery, please refer to “Battery” on page 9.
If subscription fails
Normally the handset automatically subscribes to the base station when the
cordless phone is installed. However if automatic subscription fails (the signal
strength indicator is not visible in the display), you have to manually sub-
scribe the handset to the base station see “Subscribing a DT200 handset to the
230i base station” on page 29.
Language
At this point you may wish to change the language of your handset.
6
Getting started
To change the handset menu language:
1. Press CLR the handset returns to the standby display.
>Handset
>Language
2. Go to the Handset menu using the UP or DOWN key and press YES. Using
the UP or DOWN key again, go to the Language option and press YES to
confirm. Select the language of your choice from the list and press YES.
Note if you need more information on how to use the menus please refer to
“Using the menus” on page 8.
Important. It is important to make a note of the IPEI code. You may need it to
reset the handset’s PIN code. The IPEI code can be found on a label on the
handset packaging. You can write down the IPEI code in the space provided in
“IPEI code handset” on page 24.
We also recommend that you change the PIN code of the base station immedi-
ately after installing the cordless phone. See “Changing the base station PIN
code” on page 23 for more information.
A BRIEF GUIDE
Operating range. You can use your handset in the area that is covered by the
base station. Outside this area, you will lose contact with the base station and
the signal strength indicator in the display will disappear. The warning light
will flash and you will hear short, fast, warning beeps.
Switching on. Before you can use the handset you must first switch it on.
To switch the handset on:
•
Press NO for at least one second to switch the handset on.
The standby display appears. The number on the right-hand side is the
internal number of the handset on the base station.
Home
1
Making a first call. Check that the cordless telephone is installed correctly
by dialling a person you know.
To make a call:
1. Dial the number of the person you want to call using the number keys and
press YES.
A red light appears on the top of the base station.
2. Wait for an answer and on completing your call, ask the person to call you
0:00:06
back.
020148257
3. Press NO to end the call.
Receiving a call. If someone calls you, the handset and the base station ring.
To receive a call:
1. Press YES to answer the call.
2. To end the call, press NO.
ExternalCall
020148257
Getting started
7
USING THE MENUS
The cordless phone can be operated via menus in the
handset, which are arranged in loops. For instance, you
can enter the main menu option PhoneBook by pressing
either the UP or the DOWN key. Press the UP or
DOWN key again to scroll through other options. Press
YES to confirm an option. Some options take you into
a new menu.
>PhoneBook
Handset
>Handset
BaseStation
When scrolling through the menu you can return to the
standby display or previous menu by pressing NO once
or repeatedly, at any time.
>BaseStation
Networks
If you do not press a key for a minute, the handset
reverts to the standby display.
Note The handset makes use of “dynamic” menus,
which means that some menu options may change
name or are only visible when applicable.
>Networks
Information
>Information
PhoneBook
Navigation keys.
Confirm
Back
Up
Down
Cancel menus. You can cancel any operation:
•
Press NO once or repeatedly.
The handset returns to standby.
Menu operation. The topic that follows (“Adding a name and number as an
example”) shows you how the menus work. For adding a name and number,
every step of the procedure is given in detail. For all other procedures, it is
assumed that you know your way around the menus. This guide only tells you
what menu option to select for a specific function.
To help you locate the menu options, a route through the menus is given in the
margin. These routes show you what menu options to select in sequence in
>PhoneBook
>Store
>AddNew
8
Getting started
order to get to a specific function. In most cases, the next menu option is not
immediately visible so you have to use the UP or DOWN key to locate it.
If a route through the menus is the same as the previous route except for the
last menu option, this will be indicated as shown here in the margin. See also
“Menus” on page 36 for a menu overview.
>AddLastDial
Adding a name and number as an example. You can use the AddNew option
to enter names and numbers in the phone book.
To add a new phone book entry:
>PhoneBook
>Store
1. Use the UP or DOWN key to scroll to PhoneBook and press YES.
2. Use the UP or DOWN key again scroll to Store and press YES.
3. Scroll to AddNew and press YES.
>AddNew
4. Use the number keys to enter the name. Press a key once for the first letter
of the key, press it twice for the second letter, three times for the third letter
and so on then press YES to confirm.
5. Correct the name if necessary. To delete a letter, press CLR or, if you want
to clear the entire name, press CLR for one second. These keys work in the
same way when you enter numbers.
6. Enter the telephone number and press YES to confirm.
BATTERY
The handset is powered by a rechargeable Nickel Metal Hydride (NiMH)
battery.
Charging the battery. You can fully charge a flat battery by placing the
15 hours of calling time or up to 100 hours of standby time. The handset has a
battery meter, which indicates how much power is left in the battery. You will
hear a warning sound if there is less then 15 minutes’ calling time left. To
keep the battery fully charged, you can leave the handset in the base station
without any problem.
Changing the battery. Under normal conditions the handset battery will last
at least a year. When the standby time for the handset becomes too short, you
should replace the battery. Please contact your dealer or retailer for more
information.
Warning Only use batteries as specified in “Spare parts and accessories” on
page 38.
The battery does not contain cadmium and is therefore more environmentally-
friendly than other rechargeable batteries. However, all batteries should be
disposed of properly.
Getting started
9
ATTACHING AND REMOVING THE CLIP
The handset has a clip which you can use to attach the handset to your clothes.
Do not press on the display! See the drawings below.
Tip To minimize wear and tear, we recommend that you do not remove the clip
from the handset too often.
Attaching the clip
Removing the clip
10
Getting started
Basic use and settings
TELEPHONING
Making a call
To make a call:
1. Enter the number.
The number is displayed.
053555450
2. Correct the number if necessary (CLR = delete; UP = move left; DOWN =
move right).
3. When the number is correct, press YES and wait for an answer.
Press NO to end the call.
Note When you dial a number and that number is forwarded, you see the
number to which you are forwarded in your display. This is called COLP
(Connected Line identification Presentation) and is network operator depend-
ent. See “Restricting your telephone number from being sent” on page 21 for
more information.
Receiving a call
When the handset rings:
1. Press YES to answer the call.
2. Press NO to end the call.
Sometimes the handset rings at an inconvenient moment. Press NO to mute
the ringing. Press YES if you still want to answer the call.
Caller identification. ISDN provides calling line identification. This means
that in case of an incoming call, the caller’s phone number is displayed. If the
caller’s number is included in your handset’s phone book, the corresponding
name is displayed instead.
ExternalCall
074291802
Making a call using the phone book
Your handset contains a phone book for storing names and numbers. You can
conveniently make calls using this phone book. There are several ways to
access the phone book as described below. To add names and numbers to the
phone book, see “Phone book” on page 14.
Calling by name. The call by name option lets you search for a name and
number in the phone book.
Basic use and settings
11
Calling by name:
1. Select Find&Call and press YES.
>PhoneBook
>Find&Call
2. Press the key which has the first letter of the name you are searching for.
Press once for the first letter of that key, twice for the second and three
times for the third letter of the key. To narrow down the search, you can
also enter the next letter(s) of the name.
3. Correct the name if necessary (CLR = delete; DOWN key = move left; UP
key = move right) and press YES to confirm.
The first name in the phone book beginning with the entered letter(s) or, if
it does not exist, a name beginning with the next letter is displayed.
4. If necessary scroll until you find the right name and press YES to dial the
number.
Quick call by name. You can also search for a telephone number by name in
your phone book without using the menus.
To use quick call by name:
1. Press the key which has the first letter of the name and hold down the key
until the display shows the first name in the phone book beginning with
the letter on the key you have just pressed. For the second letter of that
particular key, press the key again, without holding it down. For the third
letter, press the key again and so on.
The display shows the first name in the phone book beginning with the
chosen letter or, if it does not exist, only the letters you entered. In the lat-
ter case, the last and incorrect letter flashes. You can enter another letter to
correct it.
2. You can now enter more letters as in step 1, or scroll until you find the
right name and press YES to dial the number.
Example:
Suppose you want to call someone whose name is ‘Jones’. Press 5 and hold
until the first name in the phone book beginning with ‘J’ appears. Press 6
three times for the ‘O’. The first name in the phone book beginning with ‘Jo’
appears. You can now continue by pressing 6 twice for the ‘N’ and so on or
scroll until you find the name ‘Jones’. Press YES to dial the number.
Jones
053450512
Redialling
The last ten numbers you dialled are available for redial.
To dial one of the ten last dialled numbers:
1. Press and hold YES and wait until the last dialled number or name
appears.
The handset beeps if there are no names or numbers available for redial. If
the number appears in the phone book, the name is shown instead.
2. Scroll until you have the right number or name.
Press YES to dial for an external number or INT for an internal number.
If you press CLR instead of YES or INT for an internal number, you can edit
the number before dialling.
12
Basic use and settings
You can also access the last dialled number list via the Information menu option
LastDialled. This menu option is only available if names or numbers are availa-
ble for redial.
When you switch off your handset, the last dialled numbers are erased. To
store the last dialled numbers in your phone book. See “Adding last dialled
and a caller’s number” on page 15.
Returning a call
Unanswered calls with caller identification, are stored in the who called mem-
ory. The call info icon shows you if there are new unanswered calls. By using
the call return function, you can easily return a call to these numbers. The who
called memory holds up to ten numbers.
Check
Who Called
?
You can access the who called memory via the Information menu option
WhoCalled. This menu option is only present if names or numbers are available
for returning a call.
To return one of the last ten calls received:
1. Select WhoCalled and press YES.
>Information
>WhoCalled
A list of numbers appears. If the number appears in the phone book, the
name is shown instead.
New entries are marked with an exclamation mark. Calls that have been
answered with the handset are marked with the letter
A.
2. Scroll until you have the right number or name.
3. Press INT to dial an internal number and YES to dial an external number.
The number is removed from the who called memory and stored in the last
dialled memory.
Note If you press CLR instead of INT or YES, you can edit the number before
dialling.
When you switch off your handset, the who called list is erased. You can store
the who called numbers in the phone book. See “Adding last dialled and a
caller’s number” on page 15.
Making an emergency call
Your handset is equipped with an emergency call feature. This allows you to
call the emergency services even when the handset is blocked or direct call is
on. The emergency numbers available with this feature are 112 or 999. Check
which emergency number is for your country.
Turning off the microphone
During a call you may want to talk to someone else, without the caller
hearing.
To switch the microphone off:
•
Press CLR until you are ready to talk to the caller again.
Short beeps and the ring off icon indicate that the microphone is off.
Or
ExternalCall
Anna
Basic use and settings
13
•
Press CLR briefly.
Short beeps and the ring off icon indicate that the microphone is off. To
switch the microphone on, press CLR again.
Turning off the ringer and warning sound
If your handset rings or a warning sounds at an inconvenient moment, you can
turn off the sound.
To turn off the ring sound temporarily:
•
Press NO when the handset rings.
The ring off icon appears.
ExternalCall
Anna
The call is still there, only the ringer has been muted. The warning light and
hook icon keep flashing. Press YES if you still want to answer the call.
To turn the ring and warning sound off or on:
•
Press CLR while in standby mode.
Home
1
The ring off icon appears when the ring and warning sound are switched
off.
01–Dec 11:32
If for example you hear a low battery warning and you press CLR only the
sound is turned off. The warning light continues to flash.
You can also turn off the ringer permanently by adjusting the ring volume to
its lowest level. See “Ring volume” on page 19.
PHONE BOOK
About the phone book
Your handset contains an alphabetized phone book for 100 names and num-
bers. You can get to the phone book via the PhoneBook menu option.
Entering numbers. When you enter a phone number, there are a few things
that might be useful to know.
EnterNumber:
053405_
While entering a phone number, you can press UP to move the cursor to the
left or press DOWN to move it to the right. You can also “jump” to the far left
or right by pressing UP or DOWN respectively for one second. If you want to
delete a digit, press CLR or, if you want to clear the entire number, press CLR
for one second. These keys work in the same way when you enter names.
In certain situations you may need to insert a pause in a number to wait for the
dial tone. If so, press ꢀ for one second. A dash marks the pause.
Entering names. Use the number keys to enter names in the phone book.
Enter Name:
John_
Press a key once for the first letter of the key, press it twice for the second let-
ter, three times for the third letter and so on. To enter special characters or to
enter a digit, press the same key a few more times.
For example: to insert
Ä
press number 2 five times; to insert press number 3
È
four times and to enter a space, press number 1 once. See the table below for
more details.
14
Basic use and settings
To insert lower case letters, press the letter first and then ꢀ. To revert to upper
case letters again, press the letter and then ꢀ. To insert an asterisk (ꢀ) in a
name, press # twice.
Tip If you want a different letter to the one currently shown, you can erase the
letter with the CLR key and then enter the correct letter.
Press the corresponding key this many times for the character
Key
1
1
2
-
3
?
4
!
5
,
6
.
7
:
8
"
9
’
10 11 12 13
(
)
1
2
2
A
D
G
J
B
E
H
K
N
Q
U
X
+
C
F
I
Å
È
Ğ
5
Ä
É
İ
Æ
Ê
Ì
À
Ë
Í
Á
3
Î
Â
∆
Ï
Ã
Φ
4
Ç
Γ
3
4
5
L
Λ
Ö
ß
Ù
Ý
/
6
M
P
T
O
R
V
Y
&
Ñ
S
Ü
Z
Ø
Ş
Ú
Ÿ
$
Ò
7
Ó
Π
8
Ô
Õ
Œ
6
7
Σ
8
Û
9
9
W
0
0
@
%
£
Θ
Ξ
Ψ
Ω
#
#
ꢀ
Note Depending on the selected menu language, the character order may dif-
fer. For example when Greek is selected, Greek characters have precedence
over less frequently used characters.
Adding a name and number
You can use the AddNew option to enter names and numbers in the phone book.
To add a number to the phone book:
1. Select AddNew and press YES.
2. Enter a name and press YES to confirm.
3. Enter the telephone number and press YES to confirm.
>PhoneBook
>Store
>AddNew
Adding last dialled and a caller’s number
The last ten numbers dialled can be added to the phone book.
To add a number from the call list:
1. Select:
>PhoneBook
>Store
>AddLastDial
•
•
AddLastDial to add one of the last dialled numbers and press YES.
AddWhoCall to add a caller’s number and press YES
2. Scroll through the list of numbers until you find the number you want to
store and press YES.
>AddWhoCall
3. Edit the number if necessary and press YES to confirm.
4. Enter a name and press YES to confirm.
Changing names and numbers
Use the Edit option to change the names and numbers in the phone book. You
can correct a misspelled name or give a new name to an existing telephone
number.
Basic use and settings
15
To change a phone book entry:
1. Select Edit and press YES.
2. Enter the first letter(s) of the name you are searching for and press YES.
3. If necessary scroll to find the name, press YES again.
4. Correct the name using the number keys if necessary, press YES to
confirm.
>PhoneBook
>Find&Edit
>Edit
5. If necessary correct the number using the number keys, press YES to
confirm.
Deleting names and numbers
You can also delete names and associated numbers from the phone book.
To delete a name and number from the phone book:
1. Select Delete and press YES.
2. Enter the first letter(s) of the name you are searching for and press YES.
3. If necessary scroll to find the name, press YES to confirm.
>PhoneBook
>Find&Edit
>Delete
ADVANCED TELEPHONING
Making and receiving an internal call
To make an internal call:
1. Dial the internal telephone number and press INT.
2. Press NO to end the call
To receive an internal call:
1. Press YES to answer the call.
2. Press NO to end the call.
InternalCall
2
Each handset or device has an internal number on the base station on which it
can be contacted. See the table below for an overview.
Device
Internal number
Handset 1 - 8
All handsets
1 - 8
ꢀ
Internal or external call? When you receive a call, there is a different ring
signal for internal and external calls. You can set the tune of the ring signal for
internal and external calls yourself. This makes it easier for you to recognize
the ring signal of your own handset. For more information, please read
“Ringer tones and melodies” on page 20.
Searching for handsets or people
The cordless phone can search for handsets and any handset user on the base
station. You can call all other handsets using your handset.
To use the search function:
1. Press the ꢀ key and press INT.
All handsets connected to the base station will ring.
2. Wait for an answer.
You are connected to the first person that answers the call.
16
Basic use and settings
If you receive a search call from another handset on the base station, Page Call
Page Call
appears. Press YES to answer the call. The first to answer is connected.
Paging a handset from the base station. You can also search for or page
handsets from the base station by briefly pressing the PAGE button. To stop
the paging, press briefly the PAGE button on the base station or YES and then
NO on a handset.
Receiving a second call (call waiting)
If this function is turned on, when you are engaged in a call and another call
comes in, you are notified by two short beeps in your earpiece at regular
intervals.
When a second call is waiting you have the following options:
•
Press the R key to switch to the other call.
The first call is now on hold.
A Call Is
Waiting
You can use the R key to switch back and forth between the calls.
Or
•
•
Press the YES key to switch to the other call.
The first call is terminated.
To set the call waiting function:
Use this path to turn the call waiting function on or off.
>BaseStation
>Access
Transferring a call or consulting with another handset
The cordless phone allows you to transfer an external call to another handset.
It is also possible to consult with another handset before transferring the call
or switching back to the external call.
>CallWaiting
Transferring a call to another handset. You have an external call and want
to transfer it to a person using another handset
1. Press INT to put the external call on hold.
You hear the dial tone.
2. Dial the internal number of the handset you want to call.
If you hear the handset ring, go to step 3
If you hear a congestion tone, the handset is out of range or otherwise
engaged. return to the first call by pressing INT.
3. You now have four options:
•
Wait until the call is answered. You can now switch back and forth by
pressing INT.
•
•
•
If the call is not answered, return to the external call by pressing INT.
Transfer the external caller using NO.
Continue the call after it has been answered as a three-party call by
pressing 3.
Call back. The base station will call you back when you transfer an external
call to another handset without waiting for an answer, and the third party does
not respond within 30 seconds.
Call Back
Anna
Basic use and settings
17
You can select a different ring signal when being called back by the base sta-
tion. For more information, please read “Ringer tones and melodies” on
page 20.
Involving an external party. You have an external call and want to consult
with another external party:
1. Press the R key to put the external call on hold.
You hear the dial tone.
2. Dial the number for the external party.
If you hear the handset ring, go to step 3
If you hear a congestion tone, return to the first call by pressing the R key.
3. You have three options:
•
•
•
Wait until the call is answered. You can now switch back and forth by
pressing the R key.
If the call is not answered, return to the external call by pressing the R
key.
Continue the call after it has been answered as a three-party call by
pressing 3.
Making a three-party call
You can have a three-party call with two external parties or with one external
party and one internal party. A three-party call is also known as a conference
call.
Involving another handset. You are engaged in an external call and you
wish to involve an internal party.
1. Press INT to put the external call on hold.
You hear the dial tone.
2. Dial the internal number.
If you hear the handset ring, go to step 3
If you hear a congestion tone, return to the first call by pressing the INT
key.
3. Wait for a connection.
4. Press 3 to connect all parties.
Involving an external party. You are engaged in an external call and you
wish to involve another external party.
1. Press the R key to put the external call on hold.
You hear the dial tone.
2. Dial the external number.
If the handset is free, you hear it ring, go to step 3.
If the number you dialled is not available or engaged, you hear the busy
tone. Return to the original call by pressing R again.
3. Wait for a connection.
4. Press 3 to connect all parties.
Note To make a three-party call with two external parties the second ISDN
telephone line must be available. Only one conference call at a time is possi-
ble. No other calls can be accepted while the conference call is active.
18
Basic use and settings
When using more than one handset
If you are using more than one handset with the base station you can give all
handsets different telephone numbers or up to two handsets the same tele-
phone number. By giving the handsets different telephone numbers a particu-
lar handset can be called by its own telephone number. This makes it easy, for
example, to keep private phone calls and business phone calls separate. All
handsets will then ring according to the ringing order (see “Ringer” on
page 21) when a call is received.
Calling a particular handset. There are two ways of calling a particular
handset:
•
•
Give each handset its own telephone number (see “Multiple Subscriber
Numbers (MSN)” on page 20).
Or
A caller can also call a particular handset on the base station even when
two handsets have the same telephone number. You can call a particular
handset by dialling the telephone number followed by # and the handset’s
internal number (operator dependent). Contact your network operator for
more information.
ExternalCall
053432514#2
Setting the handset to long tones
The tones transmitted by the handset may be too short for some interactive
information services. If you have problems, you can temporarily change the
length of the tones.
If the handset is set to long tones, the tones are transmitted for the same length
of time as the keys are pressed down.
To switch the handset to long tones during a call:
Select DTMFLong and press YES.
The handset switches to long tones for the duration of the call.
>DTMFLong
>DTMFShort
•
•
To switch the handset back to short tones during a call:
Select DTMFShort and press YES.
The handset switches to short tones again.
PERSONALISING THE HANDSET
Language
>Handset
>Language
You can change the language of your handset
1. Press CLR.
The handset returns to the standby display.
2. Go to the Handset menu pressing the DOWN key 2x and press YES. Press
the UP key 3x and press YES to confirm. Use the UP or DOWN key to
scroll to the language of your choice and press YES.
Ring volume
You can adjust the handset’s ring volume via the menus.
>Handset
>Alerts
>RingVolume
Basic use and settings
19
Ringer tones and melodies
You can change the ringer tone for each call type to a different sound or a pre-
programmed melody using the RingType menu option. For each ring signal
type, you can choose from four ringer tones or six melodies.
>RingType
Discreet ringing
In the discreet ringing mode, your handset starts ringing at the lowest audible
volume level. It then gets louder and louder.
>DiscreetRng
>KeySound
Key click
You can hear a key click each time you press a key. This feature can be
switched on and off.
Display light
>Handset
>Display
>Light
Your handset has an illuminated display which lights up when a key is
pressed, when a call is received or when it is placed in or taken out of the base
station. The illumination automatically goes off when no keys have been
pressed for a while.
Display contrast
You can adjust the contrast of the display to make it easier to read.
>Contrast
Clearing all handset settings
You can clear all settings on the handset simultaneously. The menu language,
however, remains unchanged. All handset settings revert to their default
settings.
>MasterReset
PERSONALISING THE BASE STATION
Changing settings (PIN code)
If your handset is connected to the base station, you can change the base sta-
tion’s settings using the handset. You may have to enter the base station PIN
code to change these settings. For the default base station PIN code, see
page 23. To prevent others changing the settings of the base station, you
should change this code. You can find out how to do this in “Changing the
base station PIN code” on page 23.
PIN:
_
Multiple Subscriber Numbers (MSN)
With Euro-ISDN you are given up to 10 telephone numbers (operator depend-
ent). Each one of these telephone numbers, also called multiple subscriber
numbers, or MSNs, can be assigned to different handsets or other devices such
as a computer modem or fax machine. Assigning different MSNs to individual
handsets allows you to keep for instance business and personal calls sepa-
rated. You are able to assign the same MSN to a maximum of two handsets.
>BaseStation
>Basic
>PhoneLine
>PhoneNumber
Note When assigning MSNs all handsets will still ring unless you change the
ringing order. See “Ringing order” on page 21 for more information.
Presenting the handset’s internal number to the receiving party
You can send the internal number of your handset to the person you want to
call as part of the calling line identification. Go to the SUB menu to turn this
feature on or off. This feature is operator dependent.
>SUB
ExternalCall
053432514#2
20
Basic use and settings
Restricting your telephone number from being sent
When you make a phone call your telephone number is normally sent to the
person you are calling. With the CLIR (Calling Line Identification Restriction)
menu option you can prevent this information from being sent.
>BaseStation
>Basic
>PhoneLine
>CLIR
With the COLR (Connected Line identification Restriction) menu option you
can prevent a calling party seeing your phone number when you answer the
call.
>COLR
Ringer
The base station rings when an external call is received. You can adjust the
ring volume via the menu.
>BaseStation
>RingVolume
Ringing order
The base station is pre-set so that all handsets ring at the same time. However,
you can also personalise the order in which the handsets ring.
Setting the ringing order. Using a handset, you can program the order in
which the handsets ring. You are given the following options:
>BaseStation
>Basic
>RingOrder
>Priority
•
•
•
•
One means only handset 1.
One, Rest means first handset 1, then all handsets.
One, Two.. means first handset 1, then 2, then 3, etc.
All means all handsets at the same time (default).
As soon as you assign a telephone number (MSN) to a handset, you may want
to change the ringing order to One, or One, Rest One in this case stands for all
.
handsets with the same telephone number.
Note The base station will always ring to any assigned telephone number.
Setting the ring delay. You can also set the number of rings after which the
next handset starts to ring.
>Delay
Auto divert
The auto divert feature means you can be reachable by phone even when you
are out of range of the base station. When you are in range, calls are routed to
your handset. If you are out of range for any period of time, calls can be
routed to a GSM phone or a voice mailbox, for instance.
If this feature is on, the base station scans for your handset at regular intervals.
If it cannot locate the handset, it calls a certain telephone network service to
activate a diverted telephone number. As soon as the handset is located again,
the same service is called to deactivate the diverted telephone number. Ask
your dealer or retailer for more information on the call diversion service.
Auto divert can only be set for one handset. If a diverted telephone number is
activated, no calls may be received by the base station until the priority phone
handset is located again.
Setting the priority phone for auto divert. To be able to set a priority phone
for auto divert, a MSN (see“Multiple Subscriber Numbers (MSN)” on page 20
Basic use and settings
21
for more information) has to be assigned to that handset. Use menu option
PriorityNo to set a handset as a priority phone.
Setting a handset as priority phone and setting the diverted telephone
number:
1. Select PriorityNo and press YES.
>BaseStation
>PriorityNo
>AssignNo
2. Enter the PIN code for the base station (see page 23) and press YES.
3. Select AssignNo and press YES to confirm.
DeviceNo: is displayed, if a priority phone has already been set, its internal
number can be seen instead.
4. Enter the telephone number of the handset you want to assign as priority
phone and press YES to confirm.
Either EnterNumber: or Handset not known is displayed. In the latter case, a non-
existent handset number has been entered.
5. Enter the telephone number to divert to and press YES to confirm.
Deactivating the auto divert. Follow the same procedure described above
but leave the space for DeviceNo: empty then press YES to confirm. The auto
divert has now been deactivated
Single or multi-cell mode
This function (CellMode) is reserved for future use. it is recommended that you
leave the cordless phone in single-cell mode unless otherwise specified.
Clearing all base station settings
You can clear all settings on the base station simultaneously. The PIN code
and the subscriptions, however, are not cleared. All settings revert to default.
>MasterReset
PIN CODES AND BLOCKING HANDSET KEYS
Blocking handset keys
If you carry the handset in your pocket, you might accidentally press the keys
and make a call. To prevent this, you can have them automatically blocked if
you do not press a key for one minute. The keys will no longer work and a key
symbol is displayed.
>Handset
>AutoKeyLock
If the keys are blocked and you receive a call, you can still answer the call in
the normal way, without first unblocking the keys. See also “Making an emer-
gency call” on page 13.
Protecting the handset against unauthorized use
>Handset
>PhoneLock
>PowerOn
You can set the handset so that the handset PIN code must be entered after
switching it on. This feature is off by default. For the handset PIN code, see
“Overview of PIN and other codes” on page 23.
You can also secure your handset against someone adding or deleting
subscriptions.
>Subscript
Changing the handset PIN code
The handset is initially provided with a pre-set PIN code (0000). You should
change this PIN code to a personal PIN code to prevent misuse.
>ChangePIN
22
Basic use and settings
You can write down the new PIN code in the space provided in “Personal
handset PIN code” on page 24.
Resetting the handset PIN code
If your handset is blocked because an incorrect PIN code has been entered
code (see “Showing the IPEI code” on page 23) to unblock the handset.
If the handset is locked, you can still make an emergency call without first
unblocking the handset PIN code. See “Making an emergency call” on
page 13.
Showing the IPEI code
>Information
>ShowIPEI
You may need the International Portable part Equipment Identity (IPEI)
number of your handset to reset the handset PIN code when the handset is
blocked. The IPEI code is a unique code which has been assigned to the hand-
set. The IPEI code can be found on the handset packaging or in the handset’s
menu and should be written down in the space provided in the “IPEI code
handset” on page 24.
Note Contact your dealer if you can’t retrieve your IPEI code.
Changing the base station PIN code
Vital settings on the base station are secured by a PIN code to prevent access
by unauthorized people. Each time you want to change these base station set-
tings, you must enter the PIN code. You cannot switch off this security feature
but you can change the base station PIN code with your handset. For the base
station PIN code see “Overview of PIN and other codes” below.
>BaseStation
>Basic
>ChangePin
You can write the new PIN code in the space provided in “Personal base sta-
tion PIN code” below.
Resetting the base station PIN code
If you enter an incorrect base station PIN code three times in a row, the PIN
code is invalidated. Although you can still make and receive calls, you can no
longer alter the base station’s settings. After entering the PARI code, the base
station PIN code is reset to the default code (1111).
Overview of PIN and other codes
The handset and base station use several identification codes for security rea-
sons. The table below gives an overview of these codes.
Code
Value
Backdoor code
IPEI
Handset PIN
Base station PIN
0000 (default)
1111 (default)
PARI
International Portable part Unique identity assigned to your Not applicable.
Equipment Identity (IPEI) handset by the manufacturer. See
the handset packaging.
Primary Access Rights
Identity (PARI)
Unique identity assigned to your Not applicable.
base station by the manufacturer.
See the back of the base station.
Basic use and settings
23
Extra features
BABY MONITOR
You can use your handset as a baby monitor. This means you can remotely lis-
ten to the sounds in a baby’s room.
The handset being used as the baby monitor automatically makes a call to
another handset if this feature is activated. The handset mutes the ringer and
earpiece so the baby is not disturbed. All keys on the handset are blocked
except for the NO key, which you can use to end the baby monitor call.
00:10:34
BabyPhone
If the baby monitor call is interrupted, the handset displays BabyCallLost
Reactivate? and the warning light stays on continuously. If this happens, you can
press YES to re-establish the baby monitor call. You can press NO to end the
baby monitor call. If the baby monitor call is established, the other end hears a
confirmation beep every 30 seconds.
If the battery in the handset is low, the low battery warning sound will be
heard at the observer’s end to warn that the battery needs charging.
Baby phone activation
When you use the handset as a baby monitor, place it somewhere in the baby’s
room where sounds can be easily picked up.
>Handset
>BabyPhone
>Activate
Destination number
Select SetPhoneNo and enter the internal number of the handset to be used by
>SetPhoneNo
the observer.
Information tone
If the baby monitor call is switched on, the observer hears an information tone
every 30 seconds to confirm that the baby phone is active. You can switch off
the information tone if needed.
>InfoTone
DIRECT CALL
You can set the handset so that pressing any key dials a certain number. This
means that if any key is pressed, for example by a small child, the same phone
number is always immediately dialled.
Extra features
25
Switching on
To activate direct call
>Handset
>DirectCall
1. Select DirectCall and press YES.
Enable Direct Call? is displayed.
2. Press YES to confirm.
DirectC.No: is displayed. If a direct call number has already been set, this is
shown in the display.
3. Enter the direct call number with the number keys, press YES to confirm.
Note Direct call switches off the automatic key lock. For information about
automatic key lock, see “Blocking handset keys” on page 22.
If direct call is on, Direct Call and the number are displayed. To call it, press any
key on the handset. You can still make an emergency call without first switch-
ing off direct call. See “Making an emergency call” on page 13.
Switching off
If you want to switch off the direct call feature, it is important not to wait too
long between the steps, otherwise the direct call number is dialled.
>DirectCall
COST MANAGER
The base station is equipped with a call budgeting feature, which you can use
to set the amount of time or money a particular handset can spend on external
calls. When the budget for a particular handset has been exceeded, the base
station does not end an ongoing call but blocks the next external call until a
new budget is set. However, emergency calls and calls to exempt numbers can
still be made (see “Exempt numbers” on page 27).
If a particular handset has gone over its budget, a congestion tone is heard and
No Budget appears in the display when an external call is attempted.
Call budget type
Time or money can be budgeted depending on the budget type setting.
>BaseStation
>Basic
>CallInfo
Call budgets
You can set a budget for a particular handset or, if the budget is exceeded,
grant a new budget. If you set the budget for cost, your network must support
“Advice Of Charge at End of call”. The cost of the call is passed on at the end
of the call. Contact your network operator for more information.
>BaseStation
>Access
>Budget
Remaining budget
You can easily check the remaining budget of your handset. The amount can
show a negative value which means that the budget has been exceeded and no
more external calls can be made with your handset.
>Information
>CallBudget
Call barring
You can prevent certain numbers from being called from a handset by block-
ing those numbers in the base station.
CalledNumber
Is Barred
If you call a blocked number, the line gives a congestion tone.
26
Extra features
Some telephone numbers, such as emergency numbers, cannot be barred. You
can also have call barring via your telephone operator. It remains in effect irre-
spective of the call barring settings of the handset and base station. Please
consult your dealer or retailer for more information.
Switching on or off. Each handset (if you have more than one) should have
call barring set on or off separately. Call barring is off by default.
>BaseStation
>Access
>Barring
Barred numbers. You can enter three numbers of up to eight digits for call
barring. You can also bar prefixes, for instance the prefix for chat lines and
other expensive services, or the prefix for international numbers. All calls
with this prefix will then be barred.
>BarredNo
Exempt numbers. You can exempt telephone numbers, for example emer-
gency numbers, from call barring and call budgeting by the base station. This
means that these numbers can always be dialled. Some exempt numbers, such
as the national emergency number, may already have been set and cannot be
edited or removed.
>ExemptedNo
Least cost routing
>BaseStation
>Routing
If you are in a position to select different telephone operators, you can have
the base station automatically route calls to another operator if the telephone
number begins with a specific prefix. In this way, you can easily select the
operator without having to change your phone numbers.
The least cost routing function replaces the prefix of a telephone number with
digits to select the other operator. For instance, if the telephone number begins
with 00, it can be substituted by 1600 to select the other operator.
You can set four prefixes. A prefix may consist of six digits and it can be sub-
stituted by a maximum of ten digits.
Tip You can bypass this feature if you go off hook first and then dial the
number.
Call statistics handset
Your handset can tell you how long your last external call was.
>Information
>LastCall
Your handset can also display the total time of all external calls made on that
handset.
>TotalCalls
Call statistics base station
Your base station can show the total time of all external calls made.
>BaseStation
>Information
>TotalDuration
The base station can do the same for the total costs of all external calls made.
>TotCosts
VOICE MAIL NOTIFICATION
In some telephone networks, callers can leave a message in a voice mailbox if
they cannot reach you. Voice mail services normally answer calls after a given
number of rings. You can have the cordless phone notify you that someone has
left a message in your voice mail box.
Home
1
01–Dec 11:32
Extra features
27
You will be notified by a rapidly flashing message icon on the handset if a
message has been left in your voice mailbox. You can then conveniently dial
the service number of your voice mailbox using the Voice: menu option.
Checking for voice mail messages
When the message icon on the handset flashes, you can check for voice mail
messages by selecting menu option Voice: x (x is the number of messages) and
pressing YES twice.
>Voice: x
Switching on and off
Voice mail notification can be switched on or off. When you switch it on, the
voice mail service number has to be entered. Ask your dealer or retailer for
more details about the voice mail service.
>BaseStation
>VoiceMail
If no service number has been set, the voice mail notification is cleared as
soon as an external call is made.
CONNECTING HANDSETS TO BASE STATIONS
Using base stations
Before you can connect to a base station, your handset must be subscribed to
that base station. You only have to subscribe to a base station once. When you
are subscribed, you can make and receive calls whenever you are within range
manually.
While subscribing to a base station, the handset receives an internal telephone
number on which it can be called by another handset.
If your handset has a connection with a base station, this is shown by the sig-
nal strength indicator. If the indicator is visible, you can make and receive tel-
ephone calls. If the indicator is not shown, this may mean:
•
You are out of range.
No Network
No Access
Check that the base station is on and that you are within range. You must
be within range to connect to a subscribed base station. Switching to auto-
matic base station selection may remedy this (see “Selecting another base
station” on page 30).
There is no access to the selected base station.
The handset is not able to connect. Subscribe the handset to the base sta-
tion again.
•
•
There is no subscription with that base station or the subscription has been
cancelled.
You must subscribe the handset to the base station before you can connect
(see “Subscribing” below).
Subscriptions. A handset may be subscribed to up to eight base stations. The
names of these base stations are stored in a prioritized list. In case of auto-
matic base station selection, the handset tries to connect to the base station
with the highest priority; first base station entry 1, followed by base station
entry 2 etc. To change the base station priority, see “Selection priority” on
page 30.
28
Extra features
Subscribing
It is possible to subscribe the handset manually to the 230i base station. It is
also possible to subscribe theDT200 handset to a base station other than the
230i base station and even to subscribe a different handset to the 230i base sta-
tion. The three different types of subscribing are described below.
Subscribing a DT200 handset to the 230i base station. To subscribe a
handset you need the base station PIN code. This PIN code is secret and pre-
vents other handsets from subscribing to the base station without your
approval. If the handset does not have a subscription, it automatically enters
the subscription mode when it is switched on. In this case, the handset dis-
plays Press <Page> base station first and then Enter AC: appears. If so, you can skip
step two and three of the procedure below.
Note If no language has been selected then the text is displayed in English.
the first time.
To subscribe a DT200 handset to the base station:
1. Press the PAGE button on the top right side of the base station for at least
two seconds.
>Networks
>Subscribe
The base station now remains in subscription mode for five minutes.
2. Select Subscribe and press YES.
Enter AC: or Enter PIN: is displayed.
3. If Enter PIN: is displayed, enter the PIN code for the handset (see “Overview
of PIN and other codes” on page 23).
Enter AC:
Enter AC: is displayed.
4. Enter the PIN code for the base station (at delivery the PIN code is 1111,
see also page 23).
5. Press YES to confirm.
Subscribing is displayed.
6. Wait until Subscription Ready is displayed for a short time.
The handset is now connected to the base station. You can see its internal
phone number on the right-hand side of the display.
Home
2
01–Dec 11:32
If the following message is displayed, try to subscribe again:
•
Subscription Failed: the base station PIN code you have entered may be incor-
rect, or the base station already has eight handset subscriptions. To add a
handset you have to delete the subscription of another handset. See “Delet-
ing a subscription on the base station” below for more details.
At this point you may wish to change the menu language of the handset. See
“Language” on page 19 for more details.
Subscribing to a different base station. To subscribe your handset to a base
station other than the 230i:
>Networks
>Subscribe
1. Select Subscribe and press YES.
Enter AC: is displayed.
Enter AC:
2. Enter the authentication code or the PIN code of the base station.
Each digit that you enter is shown as ꢀ for security reasons.
Extra features
29
3. Press YES to confirm.
Press <Page> base station is displayed briefly and then Subscribing appears.
4. Ensure that the base station is ready to subscribe as indicated in the appro-
priate base station manual. For example, for the cordless phone 230i base
station you have to press PAGE for at least three seconds.
5. Wait until Subscription Ready is displayed for a short time.
The handset is connected to the base station. You can see its internal phone
number on the right-hand side of the display.
Home
2
01–Dec 11:32
If you get the following message, try to subscribe again:
•
Subscription Failed: the base station PIN or authentication code you have
entered may be incorrect, or the base station cannot add another
subscription.
Subscribing another handset type to the base station. Your base station
functions can be fully utilized when used in combination with a DT200 hand-
set. If it is used with another type of handset, there are a few functions that
will not work.
Please refer to the appropriate handset manual for subscribing another type of
handset to the base station. To initiate subscription, you have to press the
PAGE button on the base station for at least three seconds. The red light on
the top of the base station will then be on. The base station will remain in the
subscription mode for about 5 minutes.
Deleting a subscription on a handset
If a subscription is no longer required, you can remove it from the handset’s
subscription list.
>Networks
>Delete
Deleting a subscription on the base station
You can remove a handset subscription from the base station if that handset no
longer needs to connect to the base station.
>BaseStation
>Access
>DeSubscribe
Selecting another base station
>Networks
>SelectNet
The handset can connect to several base stations. It can select a base station
automatically when it has been out of range or is switched on. You can also
specify a base station for the handset to connect to.
Selection priority. The handset can select a base station automatically when
it has been out of range or is switched on. In this case, it searches for the base
stations in the order of priority starting with the first one on the subscription
list. If you wish to change the order of your subscription list, the base station
names can be re-arranged with this menu option.
>Priority
Changing the base station name
You can rename each subscription entry. The name is shown in the display
when the handset is connected to that base station and on standby.
>Networks
>Rename
The handset can display several special characters. Please refer to “About the
phone book” on page 14 for more details.
30
Extra features
Reference
SAFETY INSTRUCTIONS
Do not place the base station near audio or video equipment. It may cause
interference. The handset is not suitable for lifeline applications.
Intrinsic safety
Do not use the handset in conditions where there is a danger of electrically
ignited explosions.
Exposure to sunlight, heat and moisture
Do not expose the cordless phone to direct sunlight for long periods. Keep the
cordless phone away from excessive heat and moisture.
Battery disposal
Defective batteries must be returned to a collection point for chemical waste
disposal.
Spare parts and accessories
Use only approved spare parts and accessories. The operation of non-
approved parts cannot be guaranteed and may even cause damage. For more
information see “Spare parts and accessories” on page 38.
Power failure
In the event of a power failure or flat battery, you cannot use the handset to
make or receive calls.
TROUBLESHOOTING
These answers to frequently asked questions should help you solve problems
with the cordless phone yourself.
How far can I go from the base station before the handset fails?
Indoors the range is up to 50 metres, outdoors up to 300 metres. The actual
range may differ due to local circumstances.
Can anybody eavesdrop on me?
This is not possible due to the digital technology and encryption used.
Will I get a warning before the battery runs out?
An alarm will sound when approximately fifteen minutes’ calling time is left.
How can I subscribe a handset to a base station?
To subscribe a handset you need the authentication (PIN) code of the base sta-
tion. There is an explanation of how to subscribe in “Subscribing” on page 29.
Reference
31
What should I do if the handset dials a number as soon as I press
a key?
A direct call has been set. See “Direct call” on page 25.
I have called an interactive service but it does not respond to my
key presses. What is wrong?
The tones transmitted by the handset may be too short for this interactive serv-
ice. For using longer tones see “Setting the handset to long tones” on page 19.
What should I do if I do not hear anything when I pick up the
handset and the red light on the base station is flashing?
The base station is not properly connected to the telephone line. Check the
telephone line connection to the base station and ensure that the cable that
came with the set is used.
I cannot understand the language in the display. Why?
An incorrect language has been selected.
To correct this:
1. Press CLR.
The handset returns to the standby display.
2. Press the DOWN key 2x then press YES. Press the UP key 3x, and press
YES to confirm. Use the UP or DOWN key to scroll to the language of
your choice from the list and press YES.
I have entered an incorrect PIN code three times in a row. How
can I set a new PIN code?
If you have entered an incorrect PIN code three times in a row, the current
code is invalidated. To reset the PIN code, see “Resetting the base station PIN
code” on page 23 and “Resetting the handset PIN code” on page 23.
I cannot switch on the handset by pressing NO for at least two
seconds, or it switches itself off again. Why?
Place the handset in the base station. If the display comes on, the battery is
almost flat. Leave the handset in the base station to charge the battery. If the
display remains off after charging, the handset is defective or the battery is not
properly connected or may need replacing. See “Battery” on page 9.
I have placed the handset in the base station but the green
charging light does not come on. Why?
Ensure that the handset is placed properly in the base station and the base sta-
tion is on. If the battery is completely flat, leave the handset in the base station
to charge the battery. The green charging light will turn on after a few
minutes.
I know that someone is calling me, but I cannot hear the ring
signal. Why not?
If you can see the ring off icon, it means that the volume of the ring signal has
been set to zero, or the ring signal is switched off temporarily. If the ring sig-
nal has been switched off temporarily, it comes back on when you hang up.
For increasing the volume of the ring signal, see “Ring volume” on page 19.
32
Reference
The base station rings, but I can’t answer the call. Why not?
The base station does not recognise the telephone number as being assigned to
one of the handsets, therefore it is not forwarding the call to a handset. This
could mean that this number has been assigned to another device, for instance
an analogue fax machine. If you don’t want to be disturbed by this ringing,
you can turn off the volume of the base station see “Ringer” on page 21.
Someone is calling me and the phone number is displayed
instead of the name in the phone book. What is wrong?
present in the phone book at all. You can use “Adding last dialled and a
caller’s number” on page 15 to add the number to the phone book or use
“Changing names and numbers” on page 15 to change the number according
to what is displayed.
Someone is calling me, but no caller identification can be seen in
the display. What is wrong?
Only the first three handsets on the base station can show the caller identifica-
tion. It is also possible that no caller identification was sent by the network.
I cannot call certain numbers. Why not?
Call barring is on or your call budget has been exceeded. For further details,
see “Call barring” on page 26 and “Call budget type” on page 26.
Why?
There is a problem with the connection between the base station and the tele-
phone line. Check the telephone cable.
I hear a warning tone and the signal strength indicator cannot be
seen. What is wrong?
The handset is not connected to the base station. The handset is probably out
of range. Bring the handset back within range of the base station.
It is also possible that the handset has not been subscribed or that the subscrip-
tion has been cancelled. It could also mean that a base station other than the
one which you are close to has been selected. See “Using base stations” on
page 28 and “Subscribing a DT200 handset to the 230i base station” on
page 29.
I hear a warning tone and the battery icon is flashing. What is
wrong?
The battery is almost flat. Put the handset in the base station to charge the
battery.
The red light on the base station is on. What is wrong?
Nothing is wrong. The external line is busy or the subscription mode is active.
Reference
33
The base station does not work at all. What is wrong?
The telephone cable and power cord connections may be plugged into each
other’s sockets. This does not cause any harm but the base station will not
work. If this is the case, swap them over.
I cannot use the phone book. What is wrong?
To begin with, the phone book in the handset is empty. To use the phone book,
you have to add a few names and numbers. See “Adding a name and number”
on page 15.
BUTTONS, KEYS, ICONS AND SIGNALS
Buttons and keys
On the inside of the front cover of this user’s guide you will see an illustration
of the handset and base station. The lists below explain how the buttons and
keys on the handset and base station are used.
Handset.
Key
Function
VOLUME UP and
VOLUME DOWN
(side keys)
Earpiece volume louder/quieter.
Make a call or answer a call.
Confirm a menu option.
YES
If held for 1 second while in standby mode: enter the
last dialled list.
During call: microphone off.
CLR
While entering text or a number: delete last letter or
digit, delete whole line if held longer.
If the handset rings: mute sound.
While in standby mode: mute ringer and warning
sound permanently.
Cancel a menu option, handset goes on standby.
If held for 1 second: switch handset on.
If held for 1 second while in standby mode: switch
handset off.
NO
If the handset rings: mute sound.
End a call.
Cancel a menu option.
UP and DOWN
Start menu.
(arrow keys)
Scroll through menu options or lists.
While entering text or number: move one character
position, move to end or beginning if held longer.
Make an internal call.
During an external call: consult another handset.
INT
R
During an external call: transfer a call.
To answer a waiting call and to switch to a call on
hold.
Change case of previous and subsequent letters
while entering text.
ꢀ
If held for 1 second: insert dial tone pause (-) while
entering a phone number.
34
Reference
Base station.
Button
PAGE
Function
Pressed briefly: page or search for handsets
Pressed longer: subscribe a handset.
Display icons and signals
A number of icons may appear in the handset display. The list below explains
what the icons mean.
Icons
Meaning
Signal strength
On: when the handset is connected to a base sta-
tion. Five vertical bars means good reception and no
bars means no connection.
Ring off
Key
On: ring signal muted or microphone off.
On: keys locked.
Hook
On: handset is ‘off hook’.
Flashes: handset is ringing or a connection is being
set up.
Message
Call Info
Battery
Flashes quickly: new message received in the voice
mailbox.
On: new unanswered call in the call list.
On: battery charged; blocks indicate the battery
level.
Flashes: battery almost empty.
Flashes quickly: the blocks flash successively; the
battery is being charged. The steady blocks indicate
the battery level.
Signals
The handset and the base station signal certain events audibly and visually as
described below.
Handset.
Signal
Meaning
Red warning light
Incoming call.
Message waiting.
Battery almost empty.
Handset out of range or not connected.
Baby monitor call interrupted.
Reference
35
The handset also generates audible ring signals, alarm signals, warning tones
and key clicks.
Sound
Meaning
Ring signal
Alarm signal
Incoming call.
4 short beeps every 30 seconds: battery almost
empty.
4 short beeps every 2 minutes: handset out of range
or not connected.
Key click
You hear this each time you press a key (when
selected).
Warning tone
You have pressed a key which has no function.
Base station.
Signal
Meaning
Green bottom light
Red top light
On: charging handset battery.
On: an external line is engaged or subscription mode
active.
Flashes: incoming external call.
Flashes quickly: no connection to external line.
The base station also generates ring signals.
MENUS
Handset and base station functions can be accessed via the handset menus.
The chart below gives an overview of the menu options to help you locate
those functions.
The standby menu is accessible when the handset is in standby mode by press-
ing UP or DOWN.
36
Reference
AddNew (15)
AddLastDial (15)
AddWhoCall (15)
Find&Call (12)
Store (15)
find&Edit (15)
DeleteAll
>PhoneBook (14)
Edit (15)
Delete(16)
LockOff
LockOn
>Voice (27)
On
Off
Activate (25)
SetPhoneNo (25)
Infotone (25)
Internal
External
CallBack
Message
Page
AutoKeyLock (22)(
BabyPhone (25)
Alerts (19)
PhoneLock (22)
DirectCall (25)
MasterReset (20)
Language (19)
Display (20)
RingVolume (19)
RingType (20)
KeySound (20)
DiscreetRing (20)
>Handset
Click
Silent
PowerOn (22)
Subscript
ChangePIN (22)
On
Off
Light (20)
Contrast (20)
On/Off
Automatic
Barring (26)
BarredNo (26)
ExemptedNo (26)
DeSubscribe (30)
CallWaiting (16)
Budget (26)
RingVolume (21)
Routing (27)
Access
>BaseStation
Basic
PriorityPhone (21)
VoiceMail (27)
Information
Delay
RingOrder (21)
CellMode (22)
MasterReset (22)
PhoneLine
CallInfo
ChangePIN (23)
PhoneNumber (20)
COLR (11)
SUB (20)
SelectNet (30)
Priority (30)
Rename (30)
Delete (30)
ReSubscribe
Subscribe (29)
AssignNo (21)
ScanPeriod (21)
>Networks
CallBudget (26)
TotDuration (27)
TotCost (27)
WhoCalled (13)
LastDialled (12)
LastCall (27)
TotalCalls (27)
ShowIPEI (23)
>Information
Please note that some menu options may change name or are only visible when
applicable! The numbers in brackets are page numbers where the item is
described.
Reference
37
MAINTENANCE
The base station and handset do not contain user serviceable parts. If your
base station or handset require service you should return them to the dealer or
retailer from where they were bought. See also “Warranty” below.
Cleaning
Clean the cordless phone with a soft cloth moistened with water only. The use
of soap and other cleaning products can discolour and damage the cordless
phone.
Spare parts and accessories
Use only approved spare parts and accessories. The operation of non-
approved parts cannot be guaranteed and may even cause damage. Contact
your dealer or retailer for more information.
•
•
•
•
•
•
•
•
•
•
Additional DT200 handset and charger.
Clip for handset.
Desk stand for the base station.
Wall mount for base station.
ISDN telephone cable.
Power adaptor for base station.
Power adaptor for charger.
Nickel metal hydride battery for handset.
Battery cover for handset.
English user’s guide.
WARRANTY
Thank you for purchasing this Ericsson Product. To get maximum use of the
features of your new product we recommend that you follow a few simple
steps:
•
•
•
Read the “Safety instructions” on page 31.
Read all the terms and conditions of your Ericsson Warranty.
Save your original receipt. You will need it for warranty repair claims.
Should your Ericsson Product need warranty service, you should return it
to the dealer from whom it was purchased or contact your local Ericsson
helpdesk to get further information.
Our warranty
Ericsson warrants this Product to be free from defects in material and work-
manship at the time of its original purchase by a consumer, and for a subse-
quent period of one (1) year.
All accessories for the Product are covered by a warranty for a period of one
(1) year from the date of its original purchase by a consumer.
What we will do
If, during the warranty period, this Product fails to operate under normal use
and service due to improper materials or workmanship, Ericsson subsidiaries,
authorised distributors or authorised service partners will, at its option, either
38
Reference
repair or replace the Product in accordance with the terms and conditions stip-
ulated herein.
Conditions
1. The warranty is valid only if the original receipt issued to the original pur-
chaser by the dealer, specifying the date of purchase and serial number, is
presented with the product to be repaired or replaced. Ericsson reserves the
right to refuse warranty service if this information has been removed or
changed after the original purchase of the product from the dealer.
2. If Ericsson repairs or replaces the Product, the repaired or replaced Prod-
uct shall be warranted for the remaining time of the original warranty
period or for ninety (90) days from the date of repair, whichever is longer.
Repair or replacement may be via functionally equivalent reconditioned
units. Replaced faulty parts or components will become the property of
Ericsson.
3. This warranty does not cover any failure of the Product due to normal
wear and tear, misuse, including but not limited to use in other than the
normal and customary manner, in accordance with Ericsson´s instructions
for use and maintenance of the Product, accident, modification or adjust-
ment, acts of God, improper ventilation and damages resulting from liquid.
4. This warranty does not cover product failures due to repair installations,
modifications or improper service performed by a non-Ericsson authorised
service workshop or opening of the product by non-Ericsson authorised
persons.
5. The warranty does not cover product failures which have been caused by
use of non-Ericsson original accessories.
6. Tampering with any of the seals on the products will void the warranty.
7. THERE ARE NO OTHER EXPRESS WARRANTIES, WHETHER
WRITTEN OR ORAL, OTHER THAN THIS PRINTED LIMITED
WARRANTY. ALL IMPLIED WARRANTIES, INCLUDING WITH-
OUT LIMITATION THE IMPLIED WARRANTIES OR MERCHANTA-
BILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE
LIMITED TO THE DURATION OF THIS LIMITED WARRANTY. IN
NO EVENT SHALL ERICSSON BE LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES OF ANY NATURE WHATSOEVER,
INCLUDING BUT NOT LIMITED TO LOST PROFITS OR COMMER-
CIAL LOSS. TO THE FULL EXTENT THOSE DAMAGES CAN BE
DISCLAIMED BY LAW.
Some countries do not allow the exclusion or limitation of incidental or conse-
quential damage, or limitation of the duration of implied warranties, so the
preceding limitations or exclusions may not apply to you. This warranty gives
you specific legal rights, and you may also have other rights which may vary
from country to country.
Reference
39
Index
Buttons 34
A
Accessories 31, 38
Advanced telephoning 16
Advice of charge 26
Answering a call 11
AOCE 26
C
Call
budgets 26
conference 18
consulting 17
Arrow keys 8, 34
Auto divert 21
B
info icon 13, 35
on hold 17
Baby monitor 25
destination number 25
information tone 25
Back light 20
Back-door code 23
Barring
calls 26
exempt numbers 27
numbers 27
Base station
clearing settings 22
name 30
out of range 28
overview. See the beginning of the
guide 2
personalising 20
PIN code 23
ringer 21
statistics 27
time 27
waiting 17
Caller identification 11
Calling line identification 11
Cell mode 22
Changing base station name 30
Changing base station settings 20
Character map 14
Charger 38
selection 30
selection priority 30
use 28
Battery 9, 10
changing 9
disposal 31
icon 35
Blocking handset keys 22
Brief guide 7
Budget
calls 26
remaining 26
Cleaning 38
Clearing settings
base station 22
handset 20
CLIP 11
40
Index
CLIR 21
CLR key 8, 34
COLR 21
H
Handset
lock 22
overview. See the beginning of the
guide 2
Conference call 18
Connecting to base stations 28
Consulting another handset 17
Contrast 20
Cost manager 26
personalising 19
Hook
D
Direct call 25
Discreet ringing 20
Display
contrast 20
illumination 20
language 6, 19
light 20
icon 35
I
Down key 8, 34
Interference 31
Internal
E
Emergency call 13
Entering
letters 14
names 14
call 16
telephone numbers 16
Intrinsic safety 31
IPEI 23
numbers 14
voice labels 15
Environment. See the beginning of
the guide
Exempt numbers 27
Exposure 31
K
Key
click 20
icon 35
map 14
Keys 34
External call 16
Extra features 25
F
L
Frequently asked questions 31
Language
handset 6, 19
handset menu 32
Last call 27
Least cost routing 27
Letters 14
G
Getting started 5
Light 20
Long tones 19
M
Maintenance 38
Making a call 11
Index
41
Master reset
PIN code
base station 22
handset 20
handset 22
Melodies 20
Menu
overview 23
reset 23
cancel 8
operation 8
using menus 8
Menus 36
Power failure 31
Preparing for use 5
R
Message
icon 35
waiting 27
Range 31
Microphone off 13
MSN 20
Multi cell mode 22
Multiple Subscriber Numbers 20
Mute microphone 13
Reject calls 11
Remaining budget 26
Reset
base station PIN code 23
handset 20
N
Navigation keys 8
Networks 28
No key 8, 34
No network 28
Number
barring 27
volume 19
exemption 27
Ringer
O
handset 19
Operating range 7
Out of range 28
off 14
tones 20
P
Ringing order
delay 21
Paging 16
handsets 17
priority 21
PARI 23
R-key 34
PARK 23
Path through the menus 8
Phone book 14
S
about 14
Safety instructions 31
Selecting another base station 30
Side keys 34
Signal strength indicator 35
Signals 34
Single cell mode 22
Spare parts 31, 38
SUB addressing 20
add caller’s number 15
add last dialled number 15
add name and number 9, 15
changing names and numbers 15
deleting names and numbers 16
entering letters 14
entering names 14
entering numbers 14
Phone lock 22
42
Index
Subscribing 29
another handset type to the base
station 30
handset to the base station 29
Subscription
deleting on a base station 30
deleting on a handset 30
Subscriptions 28
Switching
the handset off 34
the handset on 7, 34
T
Telephoning 11
advanced 16
Three-party call 18
Total calls 27
Transferring calls 17
Troubleshooting 31
Turning
the handset off 34
the handset on 7, 34
U
Up key 8, 34
V
Voice mail notification 27
Volume
buttons 35
keys 34
W
Waiting
call 17
message 27
Wall mount 5
Warranty 38
XYZ
Yes key 8, 34
Index
43
Visit us on our web site:
EN/LZTNB 101 91/1 R1
©Ericsson Business Mobile Networks BV 2000
|