Dell ™ E1910/E2210 Flat Panel Monitor User's Guide
Notes,Cautions,Warnings
NOTE: A NOTE indicates important information that helps you make better use of your computer.
CAUTION: A CAUTION indicates potential damage to hardware or loss of data if instructions are not followed.
WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
Information in this document is subject to change without notice.
© 2009 Dell Inc. All rights reserved.
Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Inc; Microsoft and Windows are either trademarks or registered trademarks of Microsoft Corporation in
the United States and/or other countries; Adobe is a trademark of Adobe Systems Incorporated, which may be registered in certain jurisdictions. ENERGY STAR is a registered
trademark of the U.S. Environmental Protection Agency. As an ENERGY STAR partner, Dell Inc. has determined that this product meets the ENERGY STAR guidelines for energy
efficiency.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any
proprietary interest in trademarks and trade names other than its own.
Model E1910c/E1910f/E2210c/E2210f
July 2009 Rev. A00
l
VGA Cable
l
DVI Cable
l
l
l
Drivers and Documentation media
Quick Setup Guide
Safety Information
Product Features
The Dell™ E1910 flat panel display has an active matrix, thin-film transistor (TFT), liquid crystal display (LCD). The monitor features include:
■ 19-inch (482.6 mm) viewable area display.
■ 1440x900 resolution, plus full-screen support for lower resolutions.
■ Wide viewing angle to allow viewing from a sitting or standing position, or while moving from side-to-side.
■ Tilt adjustment capabilities.
■ Removable pedestal and Video Electronics Standards Association (VESA®) 100 mm mounting holes for flexible mounting solutions.
■ Plug and play capability if supported by your system.
■ On-Screen Display (OSD) adjustments for ease of set-up and screen optimization.
■ Software and documentation media which includes an information file (INF), Image Color Matching file (ICM), and product documentation.
■ Energy Saver feature for Energy Star® compliance.
■ Security lock slot.
■ EPEAT™ GOLD compliant.
■ Halogen reduced.
■ Asset Management Capability.
The Dell™ E2210 flat panel display has an active matrix, thin-film transistor (TFT), liquid crystal display (LCD). The monitor features include:
■ 22-inch (558.8 mm) viewable area display.
■ 1680 x 1050 resolution, plus full-screen support for lower resolutions.
■ Wide viewing angle to allow viewing from a sitting or standing position, or moving side-to-side.
■ Tilt adjustment capabilities.
■ Removable pedestal and Video Electronics Standards Association (VESA®) 100 mm mounting holes for flexible mounting solutions.
■ Plug and play capability if supported by your system.
■ On-Screen Display (OSD) adjustments for ease of set-up and screen optimization.
■ Software and documentation media includes an information file (INF), Image Color Matching file (ICM), and product documentation.
■ Energy Saver feature for Energy Star® compliance.
■ Security lock slot.
■ EPEAT™ GOLD compliant.
■ Halogen reduced.
■ Asset Management Capability.
Identifying Parts and Controls
Front View
Front View
Front Panel Controls
Label Description
Function buttons (For more information, see
1.
2.
Power On/Off button (with LED indicator)
Back View
Back View
Back View with Monitor Stand
Label Description
Use
1
2
3
Regulatory rating label
Security lock slot
Lists the regulatory approvals.
To help secure your monitor.
Barcode serial number label
To contact Dell for technical support.
VESA mounting holes (100mm)
(Behind attached base plate)
4
To mount the monitor.
5
6
7
Cable management slot
To organize cables by placing them through the slot.
To attach the optional Dell Soundbar.
Press to release the stand.
Dell Soundbar mounting brackets
Stand removal button
Side View
Left View
Right View
Bottom View
Bottom View
Label Description
1
2
3
AC power cord connector
DVI connector
VGA connector
Monitor Specifications
Flat Panel Specifications
Model
Dell E1910 Flat Panel Monitor
Dell E2210 Flat Panel Monitor
Active matrix - TFT LCD
TN
Screen type
Panel type
Active matrix - TFT LCD
TN
Screen dimensions
Preset display area
Horizontal
19 inches (19-inch viewable image size)
408.24 (H) X 255.15 (V)
408.24 mm (16.08 inches)
255.15 mm (10.05 inches)
0.2835 mm
22 inches (22-inch viewable image size)
473.76 (H) × 296.1 (V)
473.76 mm (18.65 inches)
296.1 mm (11.66 inches)
0.282 mm
Vertical
Pixel pitch
160° (vertical) typical, 160° (horizontal)
typical
Viewing angle
160° (vertical) typical, 170° (horizontal) typical
Luminance output
Contrast ratio
Faceplate coating
Backlight
300 CD/m² (typical)
1000 to 1 (typical)
250 CD/m² (typical)
1000 to 1 (typical)
Antiglare with hard-coating 3H
CCFL (2) edgelight system
5 ms typical
Antiglare with hard-coating 3H
CCFL (2) edgelight system
5 ms typical
Response Time
Color depth
Color Gamut
16.7 millions colors
16.7 millions colors
83% (typical)* CIE1976
83% (typical)* CIE1976
*[E1910/E2210] color gamut (typical) is based on CIE1976 (83%) and CIE1931 (72%) test standards.
Resolution Specifications
Model
Dell E1910 Flat Panel Monitor
30 kHz to 83 kHz (automatic)
56 Hz to 75 Hz (automatic)
1440 X 900 at 60 Hz
Dell E2210 Flat Panel Monitor
30 kHz to 83 kHz (automatic)
56 Hz to 75 Hz (automatic)
1680 x 1050 at 60 Hz
Horizontal scan range
Vertical scan range
Maximum preset resolution
Supported Video Modes
480i/480p/576i/576p/720p/1080i/1080P
(Supports HDCP)
Video display capabilities (DVI playback)
Preset Display Modes
E1910
Display Mode
Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz)
Sync Polarity
(Horizontal/Vertical)
VESA, 720 x 400
VESA, 640 x 480
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1152 x 864
VESA, 1280 x 800
VESA, 1280 x 1024
VESA, 1280 x 1024
VESA, 1440 x 900
31.5
31.5
37.5
37.9
46.9
48.4
60.0
67.5
49.7
64.0
80.0
56.0
70.0
60.0
75.0
60.0
75.0
60.0
75.0
75.0
60.0
60.0
75.0
60.0
28.3
25.2
-/+
-/-
31.5
-/-
40.0
+/+
+/+
-/-
49.5
65.0
78.8
+/+
+/+
-/+
+/+
+/+
-/+
108.0
83.5
108.0
135.0
106.5
E2210
Display Mode
Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz)
Sync Polarity
(Horizontal/Vertical)
VESA, 720 x 400
VESA, 640 x 480
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1152 x 864
VESA, 1280 x 1024
VESA, 1280 x 1024
VESA, 1680 x 1050
VESA, 1680 x 1050-R
31.5
31.5
37.5
37.9
46.9
48.4
60.0
67.5
64.0
80.0
65.2
64.6
70.0
60.0
75.0
60.0
75.0
60.0
75.0
75.0
60.0
75.0
60.0
60.0
28.3
25.2
-/+
-/-
31.5
-/-
40.0
+/+
+/+
-/-
49.5
65.0
78.8
+/+
+/+
+/+
+/+
-/+
+/+
108.0
108.0
135.0
146.2
119.0
Electrical Specifications
Analog RGB, 0.7 Volts +/- 5%, positive polarity at 75 ohm input impedance
Digital DVI-D TMDS, 600mV for each differential line, positive polarity at 50 ohm input
impedance
Video input signals
Separate horizontal and vertical synchronizations, polarity-free TTL level, SOG
(Composite SYNC on green)
Synchronization input signals
AC input
voltage/frequency/current
100 to 240 VAC/50 or 60 Hz + 3 Hz/1.6A (Max.)
120 V: 30 A (Max.)/240 V: 60 A (Max.) (E1910)
120V:40A (Max.)/ 240V:80A (Max.) (E2210)
Inrush current
Physical Characteristics
Model
Dell E1910 Flat Panel Monitor Dell E2210 Flat Panel Monitor
15-pin D-subminiature, blue
connector; DVI-D, white
connector
15-pin D-subminiature, blue
connector; DVI-D, white
connector
Connector type
Digital: Detachable, DVI-D, Solid Digital: Detachable, DVI-D, Solid
pins, shipped detached from
the monitor
pins, shipped detached from
the monitor
Signal cable type
Analog: Detachable, D-Sub,
15pins, shipped attached to
the monitor
Analog: Detachable, D-Sub,
15pins, shipped attached to
the monitor
Dimensions (with stand)
Height (Extended)
14.32 inches (363.74 mm)
17.45 inches (442.85 mm)
5.78 inches (146.86 mm)
16.01 inches (406.7 mm)
20.13 inches (511.2 mm)
6.44 inches (163.9 mm)
Width
Depth
Dimensions (without stand)
Height
11.41 inches (289.75 mm)
17.43 inches (442.85 mm)
2.32 inches (59.00 mm)
13.15 inches (334.0 mm)
20.13 inches (511.2 mm)
2.54 inches (64.5 mm)
Width
Depth
Stand dimensions
Height (Extended)
Width
11.39 inches (289.25 mm)
9.88 inches (250.86 mm)
5.78 inches (146.86 mm)
12.39 inches (314.7 mm)
10.47 inches (265.9 mm)
6.44 inches (163.7 mm)
Depth
Weight
12.70 lbs (5.76 kg)
11.11 lbs (5.04 kg)
7.91 lbs (3.59 kg)
2.20 lbs (1.00 kg)
Weight with packaging
15.50 lbs (7.03 kg)
13.27 lbs (6.02 kg)
Weight with stand assembly and cables
Weight without stand assembly
(For wall mount or VESA mount
considerations - no cables)
9.70 lbs (4.40 kg)
2.58 lbs (1.17 kg)
Weight of stand assembly
Environmental Characteristics
Temperature
Operating
5° to 40 °C (41° to 104 °F)
Storage: -20° to 60°C (-4° to 140°F)
Shipping: -20° to 60°C (-4° to 140°F)
Non-operating
Humidity
Operating
10% to 80% (non-condensing)
Storage: 5% to 90% (non-condensing)
Shipping: 5% to 90% (non-condensing)
Non-operating
Altitude
Operating
Non-operating
3,657.6 m (12,000 ft) max
12,192 m (40,000 ft) max
95.76 BTU/hour (maximum) 75.24 BTU/hour (typical) (E1910)
106.02 BTU/hour (maximum) 95.76 BTU/hour (typical) (E2210)
Thermal dissipation
Appendix
Dell™ E1910/E2210 Flat Panel Monitor User's Guide
WARNING: Safety Instructions
WARNING: Use of controls, adjustments, or procedures other than those specified in this documentation may result in exposure to shock,
electrical hazards, and/or mechanical hazards.
For information on safety instructions, see the Product Information Guide.
FCC Notices (U.S. Only) and Other Regulatory Information
For FCC notices and other regulatory information, see the regulatory compliance website located at www.dell.com\regulatory_compliance.
Contacting Dell
For customers in the United States, call 800-WWW-DELL (800-999-3355).
NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or
Dell product catalog.
Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services may not be
available in your area. To contact Dell for sales, technical support, or customer service issues:
1. Visit support.dell.com.
2. Verify your country or region in the Choose A Country/Region drop-down menu at the bottom of the page.
3. Click Contact Us on the left side of the page.
4. Select the appropriate service or support link based on your need.
5. Choose the method of contacting Dell that is convenient for you.
Setting Up Your Monitor
Dell™ E1910/E2210 Flat Panel Monitor
If you have a Dell™ desktop or a Dell™ portable computer with internet access
1. Go to http://support.dell.com, enter your service tag, and download the latest driver for your graphics card.
2. After installing the drivers for your Graphics Adapter, attempt to set the resolution to 1440x900 (E1910) or 1680x1050 (E2210) again.
NOTE: If you are unable to set the resolution to 1440x900 (E1910) or 1680x1050 (E2210), please contact Dell™ to inquire about a Graphics Adapter that
supports these resolutions.
Setting Up Your Monitor
Dell™ E1910/E2210 Flat Panel Monitor
If you have a non Dell™ desktop, portable computer, or graphics card
1. Right-click on the desktop and click Properties.
2. Select the Settings tab.
3. Select Advanced.
4. Identify your graphics controller supplier from the description at the top of the window (e.g. NVIDIA, ATI, Intel etc.).
5. Refer to the graphic card provider website for updated driver (for example, http://www.ATI.com OR http://www.NVIDIA.com ).
6. After installing the drivers for your Graphics Adapter, attempt to set the resolution to 1440x900 (E1910) or 1680x1050 (E2210) again.
NOTE: If you are unable to set the resolution to 1440x900 (E1910) or 1680x1050 (E2210), please contact the manufacturer of your computer or consider
purchasing a graphics adapter that will support the video resolution of 1440x900 (E1910) or 1680x1050 (E2210).
Operating the Monitor
Dell™ E1910/E2210 Flat Panel Monitor User's Guide
Power On the Monitor
Press the
button to turn on the monitor
Using the Front Panel Controls
Use the keys on the front of the monitor to adjust the image settings.
Front panel Key
A
Description
Use this button to directly access the Shortcut Key 1 (Default: Preset Modes) menu or to increase the
Preset modes
Brightness / Contrast
Menu
B
Use this button to directly access the Shortcut Key 2 (Default: Brightness/Contrast) menu or to decrease
the value of the selected menu option.
C
Use the Menu key to open the on-screen display(OSD).
D
Use the Exit key to exit on-screen display(OSD) from menu and sub-menus.
Exit
Front panel Key
Use the keys on the front of the monitor to adjust the image settings.
Front panel Key
A
Description
Use the Up key to adjust (increase ranges) items in the OSD menu.
Up
B
Use the Down key to adjust (decrease ranges) items in the OSD menu.
Down
C
Use the OK key to confirm your selection.
OK
D
Use the Back key to go back to the previous menu.
Back
Using the On-Screen Display (OSD) Menu
Accessing the Menu System
NOTE: If you change the settings and then either proceed to another menu or exit the OSD menu, the monitor automatically saves those changes. The
changes are also saved if you change the settings and then wait for the OSD menu to disappear.
1. Press the
button to open the OSD menu and display the main menu.
Main Menu
NOTE: Auto Adjust is only available when you are using the analog (VGA) connector.
2.
3.
4.
5.
6.
Press the
and
buttons to toggle between options in the Menu. As you move from one icon to another, the option name is highlighted.
button again.
buttons to select the desired parameter.
To select the highlighted item on the menu press the
Press the
Press the
Select the
and
button to enter the slide bar and then use the
or
buttons, according to the indicators on the menu, to make your changes.
to accept and return to previous menu.
to return to previous menu without accepting current settings or
The table below provides a list of all the OSD menu options and their functions.
Icon
Menu and
Submenus
Description
Brightness/Contrast Use the Brightness and Contrast menu to adjust the Brightness/Contrast.
Back
Press
to go back to the main menu.
Brightness
Allows you to adjust the brightness or luminance of the backlight.
Press the key to increase brightness and press the key to decrease brightness (min 0 ~ max 100).
Contrast
Allows you to adjust the contrast or the degree of difference between darkness and lightness on the monitor screen. Adjust
contrast only if you need further adjustment.
Press the
key to increase contrast and press the
key to decrease contrast (min 0 ~ max 100).
Auto Adjust
Use this key to activate automatic setup and adjust menu. The following dialog appears on a black screen as the monitor sel
Auto Adjustment allows the monitor to self-adjust to the incoming video signal. After using Auto Adjustment, you can further
Pixel Clock (Coarse) and Phase (Fine) controls under Display Settings.
NOTE: In most cases, Auto Adjust produces the best image for your configuration.
NOTE: AUTO ADJUST option is only available when you are using the analog (VGA) connector.
Input Source
Use the Input Source menu to select between different video signals that may be connected to your monitor.
VGA
Select VGA input when you are using the analog (VGA) connector. Push
to select the VGA input source.
to select the DVI input source.
DVI-D
Select DVI-D input when you are using the Digital (DVI) connector. Push
Select Auto Select to scan for available input signals.
Scan for Sources
Color Settings
Use the Color Settings menu to adjust the monitor's color settings.
Back
Press
to go back to the main menu.
Input Color Format
Mode Selection
Allows you to set the video input mode to:
l
l
RGB: Select this option if your monitor is connected to a computer or DVD player using the VGA and DVI cable or the H
YPbPr: Select this option if your DVD player supports only YPbPr output.
Allows you to set the display mode to:
l
l
Graphics: Select this mode if your monitor is connected to your computer.
Video: Select this mode if your monitor is connected to a DVD player.
NOTE: Depending upon the Display Mode you select the Preset Modes available for your monitor change.
Preset Mode
Allows you to choose from a list of preset color modes.
In the Graphics mode, you can set the color to the following preset values:
l
l
l
l
l
Standard: Loads the monitor's default color settings. This is the default preset mode.
Multimedia: Loads color settings ideal for multimedia applications.
Game: Loads color settings ideal for most gaming applications.
Warm: Increases the color temperature. The screen appears warmer with a red/yellow tint.
Cool: Decreases the color temperature. The screen appears cooler with a blue tint.
l
Custom (RGB): Allows you to manually adjust the color settings. Press the
and
keys to adjust the Red, Green
your own preset color mode.
In the Video mode, you can set the color to the following preset values:
l
l
l
l
Movie: Loads color settings ideal for movies. This is the default preset mode.
Game: Loads color settings ideal for most gaming applications.
Sports: Loads color settings ideal for sports.
Nature: Loads color settings ideal for nature.
Hue
Allows you to adjust the skin tone of the image. Use
or
to adjust the hue from '0' to '100'.
NOTE: Hue adjustment is available only in the Video mode.
Saturation
Allows you to adjust the color saturation of the image. Use
or
to adjust the saturation from '0' to '100'.
NOTE: Saturation adjustment is available only in the Video mode.
Reset Color Settings Resets your monitor's color settings to the factory defaults.
Use the Displays Settings menu to adjust the monitor's display settings.
Displays Settings
Back
Press
to go back to the main menu.
Horizontal Position
Use the
or
buttons to adjust image left and right. Minimum is '0' (-). Maximum is '100' (+).
NOTE: When using a DVI source, the Horizontal Position setting is not available.
Use the or buttons to adjust image up and down. Minimum is '0' (-). Maximum is '100' (+)
NOTE: When using a DVI source, the Vertical Position setting is not available.
This feature can make the image look sharper or softer. Use or to adjust the sharpness from '0' to '100'
Vertical Position
Sharpness
Pixel Clock
Phase
The Phase and Pixel Clock adjustments allow you to adjust your monitor to your preference. Use
or
buttons to adjust
If satisfactory results are not obtained using the Phase adjustment, use the Pixel Clock (coarse) adjustment and then use Ph
NOTE: Pixel Clock and Phase Adjustments are only available for "VGA" input.
Reset Display
Settings
Select this option to restore default display settings.
Select this option to adjust the settings of the OSD, such as, the languages of the OSD, the amount of time the menu remain
Other Settings
Back
Press
to go back to the main menu.
Language
Allows you to set the OSD display to one of eight languages: English, Spanish, French, German, Japanese, Brazilian Portugue
Menu Transparency Allows you to adjust the OSD background from opaque to transparent.
Menu Timer
Menu Lock
Allows you to set the time for which the OSD remains active after you press a key on the monitor.
Use the and keys to adjust the slider in 1 second increments, from 5 to 60 seconds.
Controls user access to adjustments. When Lock is selected, no user adjustments are allowed. All keys are locked except
NOTE: When the OSD is locked, pressing the menu key takes you directly to the OSD settings menu, with 'OSD Lock' pre
hold
key for 15 seconds to unlock and allow user access to all applicable settings.
DDC/CI
DDC/CI (Display Data Channel/Command Interface) allows a software on your computer to adjust the monitor display setting
balance etc.
Enable (Default): Optimizes the performance of your monitor and provides a better customer experience.
Disable: Disables the DDC/CI option and the following message appears on the screen.
NOTE: For best user experience and optimum performance of your monitor, keep this feature enabled.
This feature will help reduce minor cases of image retention. If an image appears to be stuck on the monitor, select LCD Con
image retention. Using the LCD Conditioning feature may take some time. LCD Conditioning feature cannot remove severe ca
in.
LCD Conditioning
NOTE: Use LCD Conditioning only when you experience a problem with image retention.
The below warning message appears once user selects “Enable" LCD Conditioning.
Factory Reset
Personalize
Resets all OSD settings to the factory preset values.
User can select from "Preset Modes", "Brightness/Contrast", "Auto Adjust", "Input Source" and set as shortcut key 1 and 2.
Back
Press
to go back to the main menu.
OSD Warning Messages
When the monitor does not support a particular resolution mode you will see the following message:
This means that the monitor cannot synchronize with the signal that it is receiving from the computer. See Monitor Specifications for the
Horizontal and Vertical frequency ranges addressable by this monitor. Recommended mode is 1440x900 (E1910)/1680x1050 (E2210).
You will see the following message before the DDC/CI function is disabled.
When the monitor enters the Power Save mode, the following message appears:
Activate the computer and wake up the monitor to gain access to the OSD
If you press any button other than the power button, the following messages will appear depending on the selected input:
If VGA or DVI cable is not connected, a floating dialog box as shown below appears.
or
Setting the Maximum Resolution
To set the Maximum resolution for the monitor:
1. Right-click on the desktop and select Properties.
2. Select the Settings tab.
3. Set the screen resolution to 1440x900 (E1910) or 1680x1050 (E2210).
4. Click OK.
If you do not see 1440x900 (E1910) or 1680x1050 (E2210) as an option, you may need to update your graphics driver. Depending on your computer,
complete one of the following procedures:
l
l
If you have a Dell desktop or portable computer:
Go to support.dell.com, enter your service tag, and download the latest driver for your graphics card.
If you are using a non-Dell computer (portable or desktop):
¡
¡
Go to the support site for your computer and download the latest graphic drivers.
Go to your graphics card website and download the latest graphic drivers.
¡
Using the Dell Soundbar (Optional)
The Dell Soundbar is a stereo two channel system, mountable on Dell Flat Panel Displays. The Soundbar has a rotary volume and on/off control to adjust the
overall system level, a LED for power indication, and two audio headset jacks.
1.
2.
3.
Power/volume control
Power indicator
Headphone connectors
Using the Tilt
Tilt
With the built-in pedestal, you can tilt the monitor for the most comfortable viewing angle.
NOTE: The stand is detached when the monitor is shipped from the factory.
Setting Up Your Monitor
Dell™ E1910/E2210 Flat Panel Monitor
Setting the display resolution to 1440x900 (E1910 Maximum) or 1680x1050 (E2210
Maximum)
For optimal display performance, while using the Microsoft Windows® operating systems, set the display resolution to 1440x900 (E1910) or 1680x1050
(E2210) pixels by performing the following steps:
1. Right-click on the desktop and click Properties.
2. Select the Settings tab.
3. Move the slider-bar to the right by pressing and holding the left mouse button and adjust the screen resolution to 1440x900 (E1910) or 1680x1050
(E2210).
4. Click OK.
If you do not see 1440x900 (E1910) or 1680x1050 (E2210) as an option, you may need to update your graphics driver. Please choose the scenario below
that best describes the computer system you are using, and follow the provided directions:
Dell™ E1910/E2210 Flat Panel Monitor
Information in this document is subject to change without notice.
© 2009 Dell Inc. All rights reserve
Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Inc; Microsoft and Windows are either trademarks or registered trademarks of Microsoft Corporation in
the United States and/or other countries; Adobe is a trademark of Adobe Systems Incorporated, which may be registered in certain jurisdictions. ENERGY STAR is a registered
trademark of the U.S. Environmental Protection Agency. As an ENERGY STAR partner, Dell Inc. has determined that this product meets the ENERGY STAR guidelines for energy
efficiency.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any
proprietary interest in trademarks and trade names other than its own.
Model E1910c/E1910f/E2210c/E2210f
July 2009 Rev. A00
Setting Up the Monitor
Dell™ E1910/E2210 Flat Panel Monitor User's Guide
Attaching the Stand
NOTE: The stand is detached when the monitor is shipped from the factory.
To attach the monitor stand:
1. Remove the cover and place the monitor on it.
2. Fit the two tabs on the upper part of the stand to the groove on the back of the monitor.
3. Press the stand till it snaps into its place.
Connecting Your Monitor
To connect your monitor to the computer:
1. Turn off your computer and disconnect the power cable.
Connect the blue (VGA) cable from your monitor to your computer.
NOTE: If your computer supports a white DVI connector, connect the white DVI cable (that ships with your monitor) to
the monitor and the DVI connector on your computer.
NOTE: Do not connect both the blue VGA and the white DVI cables to the computer as all monitors ship with the VGA cable
attached to the monitor.
2. Connect either the white (digital DVI-D) or the blue (analog VGA) display connector cable to the corresponding video port on the back of your
computer. Do not use both cables on the same computer. Use both the cables only when they are connected to two different computers with
appropriate video systems.
Connecting the white DVI cable
Connecting the blue VGA cable
NOTE: The Graphics are used for the purpose of illustration only. Appearance of the computer may vary.
Organizing Your Cables
After attaching all necessary cables to your monitor and computer, (See Connecting Your Monitor for cable attachment,) use the cable management slot
to organize all cables as shown above.
Attaching the Soundbar(optional)
CAUTION: Do not use with any device other than Dell Soundbar.
To attach the Soundbar:
1. Working from the back of the monitor, attach Soundbar by aligning the two slots with the two tabs along the bottom of the monitor.
2. Slide the Soundbar to the left until it snaps into place.
3. Connect the Soundbar with the power brick.
4. Plug the power cable of the brick to a nearby power outlet.
5. Insert the lime-green mini stereo plug from the rear of the Soundbar into the computer's audio output jack.
Removing the Stand
NOTE: To prevent scratches on the LCD screen while removing the stand, ensure that the monitor is placed on a clean surface.
To remove the stand:
1. Rotate the stand to allow access to the stand release button.
2. Press and hold the stand release button.
3. Lift the stand up and away from the monitor.
Wall Mounting (Optional)
(Screw dimension: M4 x 10mm).
Refer to the instructions that come with the base mounting kit. To convert your LCD display from a desk-mounted to a wall-mounted display, do the following:
1. Verify that the power button is turned Off, then disconnect the power cord.
2. Lay the LCD display face down on a soft cloth.
3. Remove the stand assembly from the back of the LCD display by pressing quick release button.
4. Attach the mounting bracket from the VESA compatible wall mounting kit (100 mm x 100 mm distance).
5. Attach the LCD display to the wall, following the instructions in the wall-mounting kit.
NOTE: For use only with UL Listed Wall Mount Bracket with minimum weight/load: 4.44kg.
Troubleshooting
Dell™ E1910/E2210 Flat Panel Monitor
Self-Test
Your monitor provides a self-test feature that allows you to check whether your monitor is functioning properly. If your monitor and computer are properly
connected but the monitor screen remains dark, run the monitor self-test by performing the following steps:
1. Turn off both your computer and the monitor.
2. Unplug the video cable from the back of the computer. To ensure proper Self-Test operation, remove both Digital (white connector) and the Analog (blue
connector) cables from the back of computer.
3. Turn on the monitor.
The floating dialog box should appear on-screen (against a black background) if the monitor cannot sense a video signal and is working correctly.
While in self-test mode, the power LED remains green. Also, depending upon the selected input, one of the dialogs shown below will continuously
scroll through the screen.
or
4. This box also appears during normal system operation, if the video cable becomes disconnected or damaged.
5. Turn off your monitor and reconnect the video cable; then turn on both your computer and the monitor.
If your monitor screen remains blank after you use the previous procedure, check your video controller and computer, because your monitor is functioning
properly.
Built-in Diagnostics
Your monitor has a built-in diagnostic tool that helps you determine if the screen abnormality you are experiencing is an inherent problem with your monitor, or
with your computer and video card.
NOTE: You can run the built-in diagnostics only when the video cable is unplugged and the monitor is in self-test mode.
To run the built-in diagnostics:
1. Ensure that the screen is clean (no dust particles on the surface of the screen).
2. Unplug the video cable from the back of the computer or monitor. The monitor then goes into the self-test mode.
3. Press and hold the 1st and 4th buttons on the front panel, simultaneously for 2 seconds. A gray screen appears.
4. Carefully inspect the screen for abnormalities.
5. Press the 4th button on the front panel again. The color of the screen changes to red.
6. Inspect the display for any abnormalities.
7. Repeat steps 5 and 6 to inspect the display in green, blue, and white colored screens.
The test is complete when the white screen appears. To exit, press the 4th button again.
If you do not detect any screen abnormalities upon using the built-in diagnostic tool, the monitor is functioning properly. Check the video card and computer.
Common Problems
The following table contains general information about common monitor problems you might encounter and the possible solutions.
Common Symptoms
No Video/Power LED off
What You Experience
No picture
Possible Solutions
l
Ensure that the video cable connecting the monitor and the computer is properly
connected and secure.
l
l
Verify that the power outlet is functioning properly using any other electrical equipment.
Ensure that the power button is depressed fully.
No Video/Power LED on
Poor Focus
No picture or no brightness
l
l
l
l
Increase brightness & contrast controls via OSD.
Perform monitor self-test feature check.
Check for bent or broken pins in the video cable connector.
Run the built-in diagnostics.
Picture is fuzzy, blurry, or
ghosting
l
l
l
l
l
Perform Auto Adjust via OSD.
Adjust the Phase and Pixel Clock controls via OSD.
Eliminate video extension cables.
Reset the monitor to Factory Settings.
Change the video resolution to the correct aspect ratio (16:10).
Shaky/Jittery Video
Wavy picture or fine movement
l
l
l
l
l
Perform Auto Adjust via OSD.
Adjust the Phase and Pixel Clock controls via OSD.
Reset the monitor to Factory Settings.
Check environmental factors.
Relocate the monitor and test in another room.
Missing Pixels
LCD screen has spots
l
l
l
Cycle power on-off.
Pixel that is permanently off is a natural defect that can occur in LCD technology.
Run the built-in diagnostics.
Stuck-on Pixels
LCD screen has bright spots
Picture too dim or too bright
Screen not centered correctly
l
l
l
Cycle power on-off.
Pixel that is permanently off is a natural defect that can occur in LCD technology.
Run the built-in diagnostics.
Brightness Problems
Geometric Distortion
l
l
l
Reset the monitor to Factory Settings.
Auto Adjust via OSD.
Adjust brightness & contrast controls via OSD.
l
l
l
Reset the monitor to Factory Settings.
Auto Adjust via OSD.
Adjust brightness & contrast controls via OSD.
NOTE: When using '2: DVI-D', the positioning adjustments are not available.
Horizontal/Vertical Lines
Screen has one or more lines
l
l
l
l
Reset the monitor to Factory Settings.
Perform Auto Adjust via OSD.
Adjust Phase and Pixel Clock controls via OSD.
Perform monitor self-test feature check and determine if these lines are also in self-test
mode.
l
l
Check for bent or broken pins in the video cable connector.
Run the built-in diagnostics.
NOTE: When using '2: DVI-D', the Pixel Clock and Phase adjustments are not available.
Synchronization Problems
Screen is scrambled or appears
torn
l
l
l
l
Reset the monitor to Factory Settings.
Perform Auto Adjust via OSD.
Adjust Phase and Pixel Clock controls via OSD.
Perform monitor self-test feature check to determine if the scrambled screen appears in
self-test mode.
l
l
Check for bent or broken pins in the video cable connector.
Restart the computer in the safe mode.
Safety Related Issues
Intermittent Problems
Visible signs of smoke or
sparks
l
l
Do not perform any troubleshooting steps.
Contact Dell immediately.
Monitor malfunctions on & off
l
Ensure that the video cable connecting the monitor to the computer is connected
properly and is secure.
l
l
Reset the monitor to Factory Settings.
Perform monitor self-test feature check to determine if the intermittent problem occurs in
self-test mode.
Missing Color
Wrong Color
Picture missing color
Picture color not good
l
l
Perform monitor self-test feature check.
Ensure that the video cable connecting the monitor to the computer is connected
properly and is secure.
l
Check for bent or broken pins in the video cable connector.
l
l
Change the Color Setting Mode in the Color Settings OSD to Graphics or Video
depending on the application.
Try different Color Preset Settings in Color Settings OSD. Adjust R/G/B value in Color
Settings OSD if the Color Management is turned off.
l
l
Change the Input Color Format to PC RGB or YPbPr in the Advance Setting OSD.
Run the built-in diagnostics.
Image retention from a static Faint shadow from the static
image left on the monitor for a image displayed appears on
l
l
Use the Power Management feature to turn off the monitor at all times when not in use
Alternatively, use a dynamically changing screensaver.
long period of time
the screen
Product Specific Problems
Specific Symptoms
What You Experience
Possible Solutions
Screen image is too small
Image is centered on screen,
but does not fill entire viewing
area
l
l
Reset the monitor to Factory Settings.
Cannot adjust the monitor withOSD does not appear on the
the buttons on the front panel screen
Turn off the monitor, unplug the power cord, plug back, and then turn on the monitor.
The picture does not fill the
entire screen.
The picture cannot fill the
height or width of the screen
l
l
Due to different video formats (aspect ratio) of DVDs, the monitor may display in full
screen.
Run the built-in diagnostics.
NOTE: When choosing DVI-D mode, the Auto Adjust function is not available.
Dell™ Soundbar Problems
Common Symptoms
What You Experience
Possible Solutions
No sound for system where
the Soundbar draws power
from an AC adapter
No power to Soundbar - the
power indicator is off
l
l
Turn the Power/Volume knob on the Soundbar clockwise to the middle position; check if
the power indicator (green LED) on the front of the Soundbar is illuminated.
Confirm that the power cable from the Soundbar is plugged into the adapter.
No Sound
Soundbar has power - power
indicator is on
l
l
Plug the audio line-in cable into the computer's audio out jack.
Set all volume controls to their maximum and ensure that the mute option is not
enabled.
l
l
l
l
Play some audio content on the computer (example, audio CD, or MP3).
Turn the Power/Volume knob on the Soundbar clockwise to a higher volume setting.
Clean and reseat the audio line-in plug.
Test the Soundbar using another audio source (For example: portable CD player, MP3
player).
Distorted Sound
Computer's sound card is used
as the audio source
l
l
l
l
l
Clear any obstructions between the Soundbar and the user.
Confirm that the audio line-in plug is completely inserted into the jack of the sound card.
Set all Windows volume controls to their midpoints.
Decrease the volume of the audio application.
Turn the Power/Volume knob on the Soundbar counter-clockwise to a lower volume
setting.
l
l
l
Clean and reseat the audio line-in plug.
Troubleshoot the computer's sound card.
Test the Soundbar using another audio source (For example: portable CD player, MP3
player).
l
Avoid using an audio cable extension or audio jack converter.
Distorted Sound
Other audio source is used
l
l
Clear any obstructions between the Soundbar and the user.
Confirm that the audio line-in plug is completely inserted into the jack of the audio
source.
l
l
Decrease the volume of the audio source.
Turn the Power/Volume knob on the Soundbar counter-clockwise to a lower volume
setting.
l
Clean and reseat the audio line-in plug.
Unbalanced Sound Output
Sound from only one side of
Soundbar
l
l
Clear any obstructions between the Soundbar and the user.
Confirm that the audio line-in plug is completely inserted into the jack of the sound card
or audio source.
l
l
l
l
Set all Windows audio balance controls (L-R) to their midpoints.
Clean and reseat the audio line-in plug.
Troubleshoot the computer's sound card.
Test the Soundbar using another audio source (For example: portable CD player, MP3
player).
Low Volume
Volume is too low
l
l
Clear any obstructions between the Soundbar and the user.
Turn the Power/Volume knob on the Soundbar clockwise to the maximum volume
setting.
l
l
l
Set all Windows volume controls to their maximum.
Increase the volume of the audio application.
Test the Soundbar using another audio source (For example: portable CD player, MP3
player)
|