INSTALLATION and SERVICE INSTRUCTIONS
USE and CARE INSTRUCTIONS
DE 6 0 GW
DUAL FUEL COOKER
distributed by
DèLo n g h i
Pty Ltd
USING THE OVEN FOR THE FIRST TIME
You are advised to carry out the following operations:
■ Furnish the interior of the oven.
■ Switch the empty oven ON at maximum temperature for about two hours
to eliminate traces of grease and smell from the components.
■ Disconnect the appliance from the electric power supply and clean the
interior of the oven with a cloth soaked in water and neutral detergent
and dry thoroughly.
IMPORTANT PRECAUTIONS AND RECOMMENDATIONS FOR
USE OF ELECTRICAL APPLIANCES
Use of any electrical appliance implies the necessity to follow a series of fundamental
rules. In particular:
■ Never touch the appliance with wet hands or feet;
■ Do not operate the appliance barefooted;
■ The appliance is not intended for use by young children or infirm persons
without supervision;
■ Young children should be supervised to ensure they do not play with the
appliance.
The manufacturer cannot be held responsible for any damages caused by improper,
incorrect or illogical use of the appliance.
This cooker has been designed and constructed in accordance with the following
codes and specifications:
AGA101 (AS 4551) Approval Requirements for Domestic Gas cooking appliances
AS/NZS 60335-1
AS/NZS 60335-2-6 Particular Requirements for Domestic electrical cooking appliances
AS/NSZ 1044 Electromagnetic Compatibility Requirements.
General Requirements for Domestic electrical appliances
3
IMPORTANT PRECAUTIONS AND RECOMMENDATIONS
After having unpacked the appliance, check to ensure that it is not damaged.
In case of doubt, do not use it and consult your supplier or a professionally qualified technician.
Packing elements (i.e. plastic bags, polystyrene foam, nails, packing straps, etc.) should not be left
around within easy reach of children, as these may cause serious injuries.
■ Do not attempt to modify the technical characteristics of the appliance as this may become dan-
gerous to use.
■ Do not carry out cleaning or maintenance operations on the appliance without having previ-
ously disconnected it from the electric power supply.
■ After use, ensure that the knobs are in the off position.
■
The appliance is not intended for use by young children or infirm persons unless they have been
adequately supervised by a responsible person to ensure that they can use the appliance safely.
■ During and after use of the appliance, certain parts will become very hot. Do not touch hot
parts. Care should be taken to avoid touching heating elements inside the oven.
■ Keep children away from the appliance when it is in use.
■ Young children should be supervised to ensure that they do not play with the appliance.
■ Some appliances are supplied with a protective film on steel and aluminium parts. This film must
be removed before using the appliance.
■ Make sure that electrical cables connecting other appliances in the proximity of the cooker can-
not come into contact with the hob or become entrapped in the oven door.
■ Do not line the oven walls with aluminium foil. Do not place baking trays or the drip tray on the
base of the oven chamber.
■ WARNING When correctly installed, your product meets all safety requirements laid down for
this type of product category. However special care should be taken around the rear or the
underneath of the appliance as these areas are not designed or intended to be touched and
may contain sharp or rough edges, that may cause injury.
■ Fire risk! Do not store flammable material in the oven and in the drawer.
■ Always use oven gloves when removing the shelves and food trays from the oven whilst hot.
■ Do not hang towels, dishcloths or other items on the appliance or its handle – as this could be a
fire hazard.
■ Clean the oven regularly and do not allow fat or oils to build up in the oven base or tray.
Remove spillages as soon as they occur.
■ Do not stand on the open oven door.
■ Always stand back from the appliance when opening the oven door to allow steam and hot air
to escape before removing the food.
■ This appliance is for domestic use only.
■ Safe food handling: leave food in the oven for as short a time as possible before and after cook-
ing. This is to avoid contamination by organisms which may cause food poisoning. Take particu-
lar care during warmer weather.
■ The manufacturer declines all liability for injury to persons or damage to property caused by
incorrect or improper use of the appliance.
■ WARNING: Taking care NOT to lift the oven by the door handle.
■ IMPORTANT NOTE: This appliance shall not be used as a space heater, espe-
cially if installed in marine craft or caravans.
4
INSTALLATION
CAUTION:
■ This appliance must be installed in accordance w ith these installation instruc-
tions.
■ This appliance shall only be serviced by authorized personnel.
■ This appliance is to be installed only by an authorised person.
■ Incorrect installation, for w hich the manufacturer accepts no responsibility,
may cause personal injury of damage.
■ Alw ays disconnect the cooker from mains pow er supply before carrying out
any maintenance operations or repairs.
■ In the room w here the cooker is installed, there must be enough air to allow
the gas to burn correctly, according to the current local regulations.
ELECTRICAL REQUIREMENTS
■ The appliance must be connected to the mains checking that the voltage corresponds
to the value given in the rating plate and that the electrical cable sections can with-
stand the load specified on the plate.
■ The plug must be connected to an earthed socket in compliance with safety standards.
■ If the appliance is supplied without a plug, fit a standard plug which is suitable for the
power consumed by the appliance.
■ The appliance must be connected directly to the mains placing a two pole switch with
minimum opening between the contacts of 3 mm between the appliance and the
mains.
■ The power supply cable must not touch the hot parts and must be positioned so that it
does not exceed 50°C above ambient.
■ Once the appliance has been installed, the switch or socket must always be accessible.
■ If the supply cord is damaged it must be replaced by the manufacturer or it’s
Service Agent or a similarly qualified person in order to avoid a hazard.
WARNING: Th is co o ke r m u st b e co n n e ct e d t o e le ct rica l su p p ly u sin g
V1 0 5 in su la t ed ca b le.
N.B. The connection of the appliance to earth is mandatory.
If the installation requires alterations to the domestic electrical system call a qualified
electrician. He should also check that the socket cable section is suitable for the power
drawn by the appliance.
Appliance power rating:
220-240 V~ 50 Hz 2400 W (10.4 A)
Replacing the pow er cord must be done by a qualified electrician in accor-
dance w ith the instructions supplied by the manufacturer and in compliance
w ith established electrical regulations.
5
CLEARANCES
Installation clearances and protection of combustible surfaces shall comply with the
current local regulations eg. AG 601 (AS 5601) Gas Installations code.
Installation shall comply with the dimension in Fig. 1 bearing in mind that.
Overhead Clearances
In no case shall the clearances between the highest part of the cooker be less than
600 mm or for an overhead exhaust fan 750 mm. AII other downward facing com-
bustible surfaces less than 600 mm above the cooker surface shall be protected for the
full width of the cooking surface in accordance with the standards noted above. In no
case shall the clearance be less than 450 mm.
Rear and Side Clearances
Where the dimensions from the periphery of the nearest burner to any vertical com-
bustible surface is less than 200 mm the surface shall be protected in accordance with
the standards to a height of not less than 150 mm above the cooking surface for the
full width or depth of the cooking surface
Where the dimensions from the periphery of the nearest burner to any horizontal com-
bustible surface is less than 200 mm, the horizontal surface shall be greater than
10 mm below the surface of the hob, or the horizontal surface requirement above.
Protection of combustible surfaces.
The standards above specify that where required protection shall ensure that the sur-
face temperature of the combustible surface does not exceed 65 °C above room tem-
perature.
If the cooker is located on a pedestal it is necessary to provide safety mea-
sures to prevent falling out.
Figure 1
105 mm
500 mm
6
LEVELLING THE COOKER
The cooker is equipped with 4 levelling feet and may be levelled by screwing or
unscrewing the feet with a spanner (fig. 4).
It is important to observe the prescriptions of figures 2a, 2b.
Figure 2a
Figure 3
0
+ 8 mm
Figure 2b
Supplied with the cooker
in a separate kit
Figure 4
+ 8 mm
+ 15 mm
A
U
T
O
7
Dotted line showing the position of
the cooker when installed
ANTI-TILT BRACKET
Important!
To restrain th e applian ce an d pre-
ve n t it tip p in g a ccid e n ta lly, fit a
bracket to its rear to fix it securely
to the w all. Make sure you also fit
the supplied lock pin to the anti-tilt
bracket.
=
=
To fit the anti-tilt bracket:
7
5
1. After you have located where the
cooker is to be positioned, mark on
0
the wall the place where the two +15
screws of the anti-tilt bracket have to
be fitted. Please follow the indica-
tions given in Fig.5a.
min 95 - max 110
(depending on feet
height adjustment)
2. Drill two 8 mm diameter holes in the
wall and insert the plastic plugs sup-
plied.
Figure 5a Fitting the anti-tilt bracket
Important!
Before drilling the holes, check that you w ill
not damage any pipes or electrical w ires.
1
3. Loosely attach the anti-tilt bracket with the two
screws supplied.
4. Move the cooker to the wall and adjust the
h eig h t of th e an ti-tilt bracket so th at it can
eng ag e in the slot on the cooker’s back, as
shown in Fig. 5a.
5. Tighten the screws attaching the anti-tilt bracket.
6. Push the cooker against the wall so that the anti-
tilt bracket is fully inserted in the slot on the cook-
er’s back.
7. Access the bracket and fit the lock pin:
• Remove the drawer (Fig. 5b).
4
• Fit the lock pin through the bracket, as shown
(Fig. 5c).
• Refit the drawer.
Figure 5b Removing the drawer
Anti-tilt bracket
attached on the
rear wall
1
2
Cooker’s
back
Lock pin
correctly
fitted
Lock pin
Slot on the
cooker’s back
Figure 5c Fitting the lock pin through
the bracket
8
GAS SUPPLY:
■ The connection must be performed by an authorised person according to the rel-
evant standards.
■ Before connecting the appliance to the gas main, mount the brass conical adap-
tor onto the gas inlet pipe, upon which the gasket has been placed (figs. 6-7).
Conical adaptor and gasket are supplied with the appliance (packed with conver-
sion kit for use with Natural gas or ULPG).
■ This appliance is suitable for use with Natural Gas or ULPG. (Check the “gas type”
sticker attached to the appliance).
■ For Natural Gas models the gas supply is connected to the pressure regulator
which is supplied with the appliance (fig. 7). Adjust the regulator to obtain a test
point pressure of 1 kPa with the two semi-rapid (SR) burners operating at maxi-
mum.
■ For ULPG models the gas supply is connected to the test point adaptor which is
supplied with the appliance (fig. 6) and ensure that the supply pressure is regulat-
ed to 2.75 kPa.
■ The connection must be made at the rear of appliance (left or right); the pipe
does not cross the cooker.
■ The inlet not used must be closed off with the cap and sealing gasket supplied.
■ IMPORTANT: Use two spanners to tighten or loosen the connecting pipe (fig. 8).
9
1. After connecting the gas supply, check the piping and connections for leaks using
a soap and water solution. The presence of bubbles indicates a leak, tighten or
replace connections as appropriate.
Warning: Do not use any naked flame to check for leaks.
2. Adjust the test point pressure or supply pressure to the value which is appropriate
for the gas type.
3. The operation of the appliance must be tested when installation is completed.
4. Turn on the appliance gas controls and light each burner individually and in com-
bination. Check for a well defined blue flame without any yellow tipping. If any
abnormality is evident then check that the burner cap is located properly and the
injector nipple is aligned correctly.
5. Check the minimum burner setting by quickly rotating the gas control knob from
the maximum to the minimum position, the flame must not go out. If adjustment is
required carry out the “minimum burner setting adjustment" procedure described
6. If satisfacfory performance cannot be obtained, the installer shall check the installa-
tion and notify the local gas supply authority for a gas supply problem, or if it is an
appliance problem, our Customer Service Centre should be called to obtain the
nearest authorized Delonghi Service Agent.
WARNING, This appliance IS NOT SUITABLE for installation with a hose
assembly.
Figure 9
Figure 8
Plug
10
CONVERSION PROCEDURE (to convert to Natural gas or to ULPG)
REPLACING THE INJECTORS
This appliance is suitable for use with Natural gas or ULPG (check the “gas type” sticker
attached to the appliance). A label stating the type of gas used after replacing the
injectors must be attached at the rear of the appliance, in proximity of the gas inlet
connection. The nominal gas consumption and injector size details are provided in
table at page 13.
To replace the injectors proceed as follows:
■ Remove pan supports and burners from the cooktop.
■ Using a spanner, remove the injector J (figs. 10a, 10b) and replace it with one
according to the gas type (see following tables - page 13).
■ Affix to the rear of the appliance, in proximity of the gas inlet connections, the
warning label (supplied with the conversion kit) stating that the cooker has
been converted for use with ULPG / Natural gas.
IMPORTANT
■ If the cooker is suitable for use with Natural gas and must be converted for use
with ULPG, before connecting to gas main remove the appliance gas regulator
and replace with test point adaptor (see figs. 6-7)
■ If the cooker is suitable for use with ULPG and must be converted for use with
Natural gas, before connecting to the gas main remove the appliance test point
adaptor and replace with gas regulator (see figs. 6-7).
NOTE:
Gas regulator and test point adaptor are supplied with the appliance (packed with
conversion kit)
Th e b u rn ers a re d esig n ed so t h a t reg u la t io n o f p rim a ry a ir is n o t req u ired .
Figure 10a
Figure 10b
J
J
11
MINIMUM BURNER SETTING ADJUSTMENT
Check whether the flame spreads to all burner ports when the burner is lit with the gas
tap set to the minimum position. If some ports do not light, increase the minimum gas
rate setting.
Check whether the burner remains lit even when the gas tap is turned quickly from
the maximum to the minimum position. If the burner does not remain lit, increase the
minimum gas rate setting.
The procedure for adjusting the minimum gas rate setting is described below.
■ Turn on the burner
■ Turn the tap to the MINIMUM position
■ Take off the knob
■ With a small flat screwdriver turn the screw “F” (fig. 11) to the correct regulation.
Normally for ULPG, the regulation screw is tightened up.
Figure 11
F
12
TABLE FOR THE CHOICE OF THE INJECTORS
Natural gas
ULPG
2.75
Test Point Pressure [kPa]
BURNER
1.0
Injector
Orifice Dia.
Gas
Consumption
Injector
Orifice Dia.
Gas
Consumption
[mm]
0.85
1.12
1.65
[MJ/h]
3.60
6.30
13.30
[mm]
0.53
0.70
0.95
[MJ/h]
3.60
Auxiliary (A)
Semi-rapid (SR)
Triple ring (TC)
6.30
11.90
LUBRICATION OF THE GAS TAPS
If the gas tap becomes stiff, it is necessary to dismantle it carefully and clean it with
petroleum spirit. Specialist high temperature resistant grease should be used to
lubricate the tap before replacing.
The operations must be carried out by an authorised person/service agent.
Figure 12
13
USE a n d CARE
CAUTION:
■ This appliance must be used only for the task it has explicitly been designed for,
that is for domestic cooking of foodstuffs. Any other form of usage is to be consid-
ered as inappropriate and therefore dangerous.
■ Do NOT place combustible materials or products on this appliance at any time.
USING THE OVEN FOR THE FIRST TIME
Operate as follow s:
■ Assemble the wire racks on the oven walls using the 2 screws (fig. 13) interposing
the catalytic panels A with the arrow up (fig. 13).
■ Slide in the grease filter on the back of the oven as in Fig. 16.
■ Slide in, on the guides, the shelf and the tray (fig. 14). The rack must be fitted so
that the safety catch, which stops it sliding out, faces the inside of the oven.
Figure 13
A
A
14
■ To eliminate traces of g rease in
manufacture it is necessary to pre-
heat the oven at the maximum tem-
perature:
Figure 14
•
For 60 minutes in the
tion, for 30 minutes in the
posi-
position and for another 15 min-
utes in the
position.
■ Unscrew the fixing screws and slide
off the wire racks and the catalytic
liners to the oven wall as in fig. 13.
The grill is secured to the rear wall
of the oven on a hinge system that
allows it to be lowered to allow
proper access when cleaning the
oven ceiling (fig. 15).
■ Clean the inside of the oven with a
cloth soaked in water and neutral
detergent and dry thoroughly.
Figure 15
Figure 16
GREASE FILTER
■ A special screen is provided at the
back of the oven to catch grease
particles, mainly w hen meat is
being roasted fig. 16).
■ Clean the filter after any cooking!
The grease filter can be removed
fo r cle a n in g a n d sh o u ld b e
w ashed reg ularly in hot soapy
water (fig. 16).
■ Alw ays d ry th e filte r p ro p e rly
before fitting it back into the oven.
CAUTION: When baking pastry etc. this
filter should be removed.
15
TELESCOPIC SLIDING SHELF SUPPORTS
The telescopic sliding shelf supports make it safer and easier to insert and remove the
oven shelves and trays. They stop when they are pulled out to the maximum position.
Important! When fitting the sliding shelf supports, make sure that you fit:
■ The slides to the top wire of a rack. They do not fit on the lower wire.
■ The slides so that they run out towards the oven door.
■ Both sides of each pair of shelf slides.
■ Both sides on the same level.
■ Note:
you must not fit the sliding shelf supports to the top shelf position (fig 17).
To fix the sliding shelf support onto the side racks:
■ Screw the side rack onto the oven wall interposing the catalytic panels (Fig. 13).
■ Fit the sliding shelf support onto the top wire of a rack and press (Fig. 17). You will
hear a click as the safety locks clip over the wire.
Figure 17
Left
Right
16
To remove the telescopic sliding shelf supports:
– Remove the side racks and the catalytic liners by unscrewing the fixing screws
(Fig. 18).
– Lay down the telescopic sliding shelf support and side racks, with the telescopic slid-
ing shelf support underneath.
– Find the safety locks. These are the tabs that clip over the wire of the side rack (arrow
1 in Fig. 19).
– Pull the safety locks away from the wire to release the wire (arrow 2 in Fig. 19).
Cleaning the sliding shelf supports
– Wipe the supports with a damp cloth and a mild detergent only.
– Do not wash them in the dishwasher, immerse them in soapy water, or use oven
cleaner on them.
Figure 19
Figure 18
1
2
1
17
CONTROL PANEL
Figure 20
8
P
A
U
T
O
7
6
5
4
3
2
1
CONTROL PANEL - Controls description
1. Front right burner control knob
2. Rear right burner control knob
3. Rear left burner control knob
4. Front left burner control knob
5. Multifunction oven switch knob
6. Multifunction oven thermostat knob
7. Electronic programmer
Pilot lamp:
8. Oven thermostat indicator light
Plea se n o t e: This appliance incorporates a safety cooling fan which you will hear
operating whenever the oven or grill are in use. This fan is to reduce the external
temperature of the appliance and cool the internal components.
18
GAS HOB
Figure 21
3
2
1
4
GAS BURNERS
Natural Gas
MJ/h
ULPG
MJ/h
1. Auxiliary burner (A)
3.6
6.3
6.3
3.6
6.3
6.3
2. Semi-rapid burner (SR)
3. Semi-rapid burner (SR)
4. Triple ring burner (TC)
13.3
11.9
19
LIGHTING GAS BURNERS
FITTED WITH SAFETY VALVE DEVICE AND ELECTRONIC IGNITION
Figure 22
■ Check that the electricity is
switched on to allow spark igni-
tion.
■ Make sure that all controls are
turned to zero.
■ The gas flow to the burner is
controlled by taps with safety
cutout device. If the burner
flame should go out, the safety
cut-off valve will automatically
stop the gas flow. The switch for
the electric ignition is incorporat-
ed in the knobs.
■ You control the flow by turning the knob
indicator to line up with the following symbols:
– Symbol
: tap closed (burner off)
– Symbol
– Symbol
: High (maximum)
: Low (minimum)
■ To ignite automatically, push the required knob down and turn it to maximum,
keeping the knob down until the burner lights. When the flame is lit, wait for
about ten second with the knob down (safety cut-off activation delay).
■ You can control the temperature by the knob to “High” (maximum) from “Low”
(minimum).
■ To switch off, turn the knob clockwise until you hear the safety click.
■ Note that, if you are using a burner at the minimum setting, you turn the knob
clockwise past the maximum setting before reaching the off position.
■ Whenever the lighting of the burners is difficult due to peculiar conditions of
the gas features or supply, it is advised to repeat the ignition with the knob on
“minimum” position.
■ If when lighting any of the burners an abnormal flame appears, switch the
burner off and relight using the minimum setting.
■ If the flame is still not correct, turn the burner off and call our Customer Service
center for your nearest Authorized Delonghi Service Agent.
■ In the case of a mains failure light the burner with a match or lighted taper.
20
CHOICE OF BURNER
The burner must be chosen according to the diameter of the pans and energy
required.
For optimum efficiency uso a wok or pan no smaller than 230 mm diameter.
Figure 23
d o n o t u se p a n s w it h co n ca ve o r co n vex b a ses
Burners
Auxiliary
Semi-rapid
Triple ring
Wok
Pan diameter
12 - 14 cm
*
16 - 24 cm
26 - 28 cm
max 36 cm
( ) with grill for small cookware: minimum diameter 6 cm.
*
Saucepans with handles which are excessively heavy, in relationship to the weight
of the pan, are safer as they are less likely to tip.
Pans which are positioned centrally on burners are more stable than those which
are offset.
It is far safer to position the pan handles in such a way that they cannot be
accidentally knocked.
When deep fat frying fill the pan only one third full of oil.
DO NOT cover the pan with a lid and DO NOT leave the pan unattended.
In the unfortunate event of a fire, leave the pan where it is and turn off all
controls.
Place a damp cloth or correct fitting lid over the pan to smother the flames.
DO NOT use water on the fire.
Leave the pan to cool for at least 30 minutes.
21
CORRECT USE OF TRIPLE-RING BURNER
■ The flat-bottomed pans are to be placed directly onto the pan-support.
■ To use the WOK, you must place the wok stand in the CORRECT position as
shown in Fig. 24a-24b.
IMPORTANT:
The special grille for wok pans (fig. 24b) MUST BE PLACED ONLY over the pan-rest for
the triple-ring burner.
Figure 24a
Figure 24b
WRONG
CORRECT
Figure 25
GRATE FOR SMALL PANS
(fig. 25)
This grate is to be placed on top of the
(smaller) auxiliary burner when using
small diameter pans, in order to prevent
them from tipping over.
22
MULTIFUNCTION OVEN
GENERAL FEATURES
With the Multi-Function oven it is possible to cook a variety of food using the 6 different
cooking functions.
These 6 cooking functions are obtained using a combination of the 4 different heating
elements plus a defrost function using the fan only.
OPERATING PRINCIPLES
Heating and cooking in the MULTI-FUNCTION oven are obtained in the following
ways:
a. by normal convection
The heat is produced by the upper and lower heating elements.
b. by forced convection
The fan draws in air contained within the oven housing at the rear of the oven and
forces it over the circular heating element. The hot air envelops the food in the oven
givin faster and more even cooking before it is drawn back into the housing to
repeat the cycle. It is possible to cook several dishes simultaneously due to the even
distribution of heat within the oven.
c. by forced semi-convection
The heat produced by the top and bottom heating elements is distributed through-
out the oven by the fan.
d. by radiant heat
The food is grilled by the infra red grill element.
e. by radiant heat and ventilation
The food is grilled by the grill element is distributed throughout the oven
f. by ventilation
The food is defrosted by using the fan only function without heat.
WARNING:
The door is hot, use the handle.
During use the appliance becomes hot. Care should be taken to avoid touching
heating elements inside the oven.
23
Figure 26
THERMOSTAT KNOB
This only sets the cooking temperature and does not switch the oven on.
Rotate clockwise until the required temperature is reached (from 50 °C to 250 °C).
FUNCTION SELECTOR KNOB
Rotate the knob clockwise to set the oven for one of the following functions.
OVEN LIGHT
By setting the knob to this position, only the oven light comes on.
It remains on in all the cooking modes.
TRADITIONAL CONVECTION COOKING
The upper and lower heating elements come on. The heat being dispersed by natural
convection. The temperature range must be set between 50 °C and 250 °C using the
thermostat.
The oven must be preheated before cooking.
Ideal for:
Food that requires the same degree of cooking both inside and out, for example
roasts, spare pork ribs, meringues etc.
24
GRILLING
The infrared grill element at the top of the oven comes on. The heat is dispersed by
radiation. Use with the o ve n d o o r clo se d and the thermostat knob to position
between 50 °C and 200 °C max.
For cooking hints, see the chapter “USE OF THE GRILL”.
Ideal for:
Intense grilling, browning, cooking au gratin and toasting etc.
It is recommended that you do not grill for longer than 30 minutes at any
one time.
Attention: the oven door becomes very hot during operation.
Keep children aw ay.
DEFROST
Only the oven fan comes on. Use with the thermostat knob set to “ ” - other temper-
ature have no effect. The food is thawed by ventilation without heating.
Ideal for:
Quick thawing of frozen foods; one kg requires approximately 1 hour.
Thawing times vary according to the quantity and type of food to be thawed.
FAN FORCED
The circular element and fan come on. The heat is dispersed by forced convection and
the temperature can be varied to between 50 °C and 250 °C via the thermostat knob.
The oven does not require preheating.
Ideal for:
Food which has to be well-cooked outside and soft or rosy inside, for example
lasagne, lamb, roast beef, whole fish etc.
25
FAN GRILL
Both the grill and the fan come on. Most of the cooking is done by grilling and then
the hot air circulated around the oven. The oven door should be kept closed.
The temperature can be set between 50 °C and 200 °C max.
The oven should be preheated for 5 minutes before cooking. For further cooking hints
see “GRILLING AND COOKING AU GRATIN”.
Ideal for:
Quick sealing in of food juices for example such as hamburger, chicken pieces, chops.
It is recommended that you do not grill for longer than 30 minutes at any
one time.
Attention: the oven door becomes very hot during operation.
Keep children aw ay.
MAINTAINING TEMPERATURE AFTER COOKING OR
SLOWLY HEATING FOODS
The upper element, the circular element and the fan come on.
The heat is circulated by forced convection with greater intensity in the upper part.
The temperature can be set to between 50 °C and 140 °C via the thermostat knob.
Ideal for:
Keeping food warm after any type of cooking. Slow heating of cooked food.
MULTI-FUNCTION
The upper and lower heating elements come on and the fan come on - the heat from
the element being circulated by the fan.
The temperature range can be set to between 50 °C and 250 °C using the thermostat.
Ideal for:
Large bulky quantities of food that require even cooking throughout for example large
roasts, turkey, roast turkey, cakes etc.
26
COOKING ADVICE
Remember to keep children away from the appliance when you use the grill or oven, since
these parts become very hot.
STERILIZATION
Sterilization of foods to be preserved, in full and hermetically sealed jars, is done in the
following way:
a. Set the switch to position
.
b. Set the thermostat knob to position 185 °C and preheat the oven.
c. Fill the dripping pan with hot water.
d. Set the jars onto the dripping pan making sure they do not touch each other and
the door and set the thermostat knob to position 135 °C.
When sterilization has begun, that is, when the contents of the jars start to bubble,
turn off the oven and let cool.
Check your recycle book for full instructions.
WARMING BREAD
Set the switch to position
and the thermostat knob to position 150 °C.
Bread becomes fragrant again if wet with a few drops of water and put into the oven
for about 10 minutes at the highest temperature.
SIMULTANEOUS COOKING OF DIFFERENT FOODS
The oven set on position
can cook several different foods together. Foods as
diverse as fish and cakes can be cooked together without the cross transference of
flavours. This is because the fats and cooking smell that would normally be
deposited on the different foods are oxidised and are not absorbed by the foods.
The cooking temperature of the foods, however must be within 20 - 25 °C of
each other. The food with the longest cooking time will be put into the oven first
and the other foods are added as necessary according to their cooking times.
ROASTING
To obtain classical roasting, it is necessary to remember:
■ that it is advisable to maintain a temperature between 180 °C and 200 °C.
■ that the cooking time depends on the quantity and the type of foods.
27
GRILLING AND COOKING AU GRATIN
As the hot air completely covers the food to be cooked, grilling may be done with
the food on the rack in the oven. The knob should be switched to position
The thermostat should be set to 50 °C and 200 °C max and the oven pre-
heated.
.
The food should be placed on a rack in the oven for the required cooking time.
Adding a few dabs of butter before the end of the cooking time gives the golden “au
gratin” effect.
It is recommended that you do not grill for longer than 30 minutes at any
one time.
USE OF THE GRILL
Preheat the oven for about 5 minutes with the door closed.
Introduce the food to be cooked, positioning the rack as close to the grill as possible.
The dripping pan should be placed under the rack to catch the cooking juices and
fats.
Do not grill for longer than 30 minutes at any one time.
W ARNING: Acce ssib le p a rts m a y b e co m e h o t w h e n th e g rill is u se d .
Children should be kept aw ay.
28
RECOMMENDED COOKING TEMPERATURE
Food
°C
°F
Gas
Shelf
Cooking
Mark
Position*
Time (approx)
CAKES
Victoria sandwich
Small cakes/buns
Maidera cake
Fruit cake
190
190
180
170
150
225
375
375
350
325
300
425
5
5
2 or 3
1 and 2
2 or 3
3
20-25 mins
15-20 mins
20 mins
13/4 hours
21/2 hours
8-10 mins
4
3
Rich fruit cake
Scones
2
3 or 4
2
8-9
PASTRY
Puff
225
200
425
400
8-9
6
2
10-20 mins
20-30 mins
30-35 mins
40-45 mins
Short crust
Plate tarts
Quiches and flans
2
200-210
200-210
400-410
400-410
6
1 or 2
1 or 2
6
YEAST
Bread loaf
Bread rolls
Pizza dough
225
220
230
425
425
450
7-8
7
2
1 or 2
2
35-55 mins
15-20 mins
20 mins
8
ROAST MEAT
Beef – Medium
Lamb
190
190
375
375
5
5
2 or 3
2 or 3
2 or 3
2 or 3
2 or 3
2 or 3
2 or 3
20 mins/lb + 20 mins
25-30 mins/b + 25 mins
30 mins/lb + 30 mins
30 mins/b + 30 mins
30 mins/b + 30 mins
18-20 mins/b + 20 mins
11/2 2 hours
Pork
190-200
190
375-400
375
5-7
5
Veal
Chicken
190
375
5
Turkey up to 10lb
Stews/casseroles
180
350
4
150-170
300-325
2-3
N.B. For fan ovens reduce the temperature
by 10-20°C. For any dish taking one hour or
over to cook, reduce the cooking time by 10
minutes per hour.
Shelf positions have been counted from
*
the top of the oven to the base.
A fan oven creates more even temperature
throughout, therefore the shelf positions are
not as critical.
29
ELECTRONIC PROGRAMMER
The electronic programmer is a device which groups together the following functions:
■ 24 hours clock with illuminated display
■ Timer (up to 23 hours and 59 minutes)
■ Program for automatic oven cooking (main oven only)
■ Program for semi-automatic oven cooking (main oven only)
Description of the buttons:
Automatic cooking taking place
Timer
Timer in operation
Cooking time
and AUTO - flashing - Programme
error.
End of cooking time
(The time of day lies between the
calculated cooking start and end
time).
Manual position and cancella-
tion of the inserted cooking
programme
N o t e : Se le ct a fu n ctio n b y th e
respective button and, in 5 seconds, set
Advancement of the numbers
of all programs
the required time w ith the
buttons (“one-hand” operation).
/
Turning back of the numbers
of all programs and changing
the frequency of the audible
signal.
A p o w e r cu t ze ro e s th e clo ck a n d
cancels the set programmes.
Description of the lighted symbols:
AUTO - flashing - Programmer in auto-
matic position but n ot pro-
grammed
AUTO - always lighted - Programmer in
automatic position with pro-
gramme inserted.
Figure 28
Figure 27
A
U
T
O
30
ELECTRONIC CLOCK (fig. 28)
ELECTRONIC TIMER
The programmer is equipped with an
electronic clock with lighted numbers
which indicate hours and minutes.
Upon immediate connection of the
oven or after a blackout, three zeroes
will flash on the programmer panel.
To set the hour it is necessary to push
The timer programme consists only of a
b u zze r w h ich ma y b e se t fo r a
maximum period of 23 hours and 59
minutes.
If the AUTO is flashing push the
button.
To set the time, push the
a n d th e o r
button
u n til yo u
the
or
button and then the
button until you have set the
obtain the desired time (fig. 30).
Having finished the setting, the normal
time will appear on the panel and the
symbol will appear.
exact hour (fig. 28).
Alternatively, simultaneously push the
two buttons and at the
same time push the
button.
or
The countdown will start immediately
and may be seen at any moment on
the panel by simply pressing the button
.
No te : Setting the clock deletes any
programme.
At the end of the time, the
symbol
NORMAL COOKING
WITHOUT THE USE OF THE
PROGRAMMER
To manually use the oven, that is, without
the aid of the programmer, it is necessary
to cancel the flashing AUTO by pushing
will be switched off and an intermittent
buzzer will go off; this can be stopped
by pressing any one of the buttons.
the button
off and the symbol
29).
(AUTO will be switched
will go on - Fig.
ALTERING THE AUDIBLE
SIGNAL
Attention: If the AUTO is not flashing
(which means a cooking programme has
already been inserted), by pushing the
By pressing the
button you can
choose from three variations.
button
you have cancelled the
programme and switched to manual.
Figure 29
Figure 30
31
3.Set the temperature and the cooking
programme by using the switch and
thermostat knobs of the oven (see
specific chapters).
Now the oven is prog rammed and
everything will work automatically, that
is the oven will turn on at the right
moment to end the cooking at the
established time.
AUTOMATIC OVEN
COOKING
To cook food automatically in the oven,
it is necessary to:
1.Set the length of the cooking time
2.Set the end of the cooking time
3.Set the temperature and the oven
cooking programme.
Du rin g co o kin g , th e
remains on.
symb o l
Th e se o p e ra tio n s a re d o n e in th e
following way:
1.Set the length of the cooking time by
By pushing the
button you can
see the time that remains until the end
of cooking.
pushing the
button to
button and the
advance, or
Th e co o kin g p ro g ra mme ma y b e
cancelled in any moment by pushing
.
At the end of the cooking time the
oven will turn off automatically, the
symbol will turn off, AUTO will flash
and a buzzer will sound, which can be
turned off by pushing any of the but-
tons.
to go back if you have passed the
desired time (fig. 31). The AUTO and
the
2.Set the end of the cooking time by
p re ssin g th e b u tto n (th e
symbol will be on.
cooking time already added to the
clock time w ill ap p ear), an d th e
button (fig. 32); if you pass the
desired time you may get back by
pushing the
button.
Turn the switch and thermostat knobs
to zero and put the programmer onto
“ma n u a l” b y p re ssin g th e
button.
After this setting, the
symbol will
go off. If after this setting, the AUTO
flashes on the panel and a buzzer
goes off, it means there was an error
in the programming.
In th is ca se , mo d ify th e e n d o f
cooking time or the cooking time
itse lf b y fo llo w in g th e a b o ve
instructions again.
At t e n t io n : A power cut makes the
clock go to zero and cancels the set
programmes.
After a power cut three zeroes will flash
on the panel.
Figure 32
Figure 31
32
At the end of cooking, the oven and
the symbol will turn off, the AUTO
will flash and a buzzer will sound; that
can be stopped by pushing any of the
buttons.
Turn the switch and thermostat knobs
to zero and put the programmer onto
SEMI-AUTOMATIC
COOKING
This is used to automatically switch off
the oven after the desired cooking time
has elapsed.
There are two ways to set your oven:
1. Set the length of the cooking time by
“manual” by pressing the
button.
pushing the
button and the
button to advance, or
to go backwards if you have passed
the desired time (Fig. 33).
or
2. Set the end of the cooking time by
pushing the
button and the
button to advance, or
to go backwards if you have passed
the desired time (Fig. 34).
Figure 33
AUTO and the
symbol will be
on.
Then set the temperature and the
cooking programme using the oven
switch and thermostat knobs (see
specific chapters).
The oven is switched on and it will
be switched off automatically at the
end of the desired time.
Du rin g co o kin g , th e
re main s o n an d b y p re ssin g th e
button you can see the time
symb o l
th a t re ma in s till th e e n d o f th e
cooking.
Th e cookin g p rog ramme can be
cancelled at any moment by pushing
Figure 34
the
button.
33
Clea n in g a n d Ma in t en a n ce
Maintenance
Period
Description
Daily
• Clean gas cooktop as per instructions below
• Remove burner caps, burner rings & base and clean using
non abrasive detergent & rinse in cold water & dry thoroughly
before replacing back on hob
Monthly
• Clean ignitor tip & thermocouple using damp soapy cloth and
dry thoroughly
• Contact your local authorized gas Service Agent to perform
a thorough check on all gas components on the gas cooker
3 - 4 Yearly
GENERAL ADVICE
■ Before you beg in clean in g , you mu st en su re th at th e applian ce is
sw itched off.
■ It is advisable to clean when the appliance is cold and especially when cleaning
the enamelled parts.
■ Avoid leaving alkaline or acidic substances (lemon juice, vinegar, etc.) on the
surfaces.
■ Avoid using cleaning products with a chlorine or acidic base.
■ Do n ot use a steam clean er because th e moisture can g et in to th e
appliance thus make it unsafe.
WARNING
When correctly installed, your product meets all safety requirements laid down for this
type of product category. However special care should be taken around the rear or
the underneath of the appliance as these areas are not designed or intended to be
touched and may contain sharp or rough edges, that may cause injury.
ENAMELLED PARTS
All the enamelled parts must be cleaned with a sponge and soapy water only or other
non-abrasive products.
Dry preferably with a microfibre or soft cloth.
STAINLESS STEEL SURFACES
The stainless steel front panels on this cooker (facia, oven door, drawer) are protected
by a finger-print proof lacquer. To avoid damaging this lacquer, do not clean the stain-
less steel with abrasive cleaners or abrasive cloths or scouring pads.
ONLY SOAP/WARM WATER MUST BE USED TO CLEAN THE STAINLESS STEEL
SURFACES.
34
INSIDE OF OVEN
■ The oven should always be cleaned after use when it has cooled down.
The cavity should be cleaned using a mild detergent solution and warm water.
Suitable proprietary chemical cleaners may be used after first consulting with the
manufacturers recommendations and testing a small sample of the oven cavity.
Abrasive cleaning agents or scouring pads/cloths should not be used on the cavi-
ty surface.
■ NOTE: The manufacturers of this appliance will accept no responsibility for dam-
age caused by chemical or abrasive cleaning.
■ Do not store flammable material in the oven.
ADVICE FOR USE AND MAINTENANCE OF CATALYTIC
PANELS
The catalytic panels are covered with special microporous enamel which absorbs and
does away with oil and fat splashes during normal baking over 200°C.
If, after cooking very fatty foods, the panels remain dirty, operate the oven “idling” on
max temperature for about 30 minutes. These panels do not require to be cleaned,
however it is advised to periodically remove them from the oven (at least the side pan-
els) and to wash them with tepid soapy water and then wipe off with a soft cloth.
DO NOT CLEAN OR WASH THEM WITH ABRASIVE PRODUCTS OR WITH
PRODUCTS CONTAINING ACIDS OR ALKALIS.
The side panels are reversible and when the catalytic microporous enamel degrades,
they can be turned to the other side.
GAS TAPS
If the gas taps are not working properly, call our Customer Service Centre to obtain the
nearest Authorized Delonghi Service Agent.
GRILL HEATING ELEMENT
■ The heating element is self-cleaning and does not require maintenance. The grill
is secured to the rear wall of the oven on a hinge system that allows it to be
lowered to allow proper access when cleaning the oven ceiling.
35
GREASE FILTER
Clean the filter after any cooking!
The grease filter can be removed for cleaning and should be washed regularly in hot
soapy water (fig. 16 at page 15).
Always dry the filter properly before fitting it back into the oven.
REPLACING THE OVEN LIGHT
Before any maintenance is started involving electrical parts of the appliance,
it must be disconnected from the pow er supply.
• Let the oven cavity and the heating elements cool down;
• Switch off the electrical supply;
• Unscrew the protective cover B (fig. 35);
• Unscrew and replace the bulb A with a new one suitable for high temperatures
(300 °C) having the following specifications: 230-240 V~ 50 Hz, E14 and same power
(check watt power as stamped in the bulb itself) of the replaced bulb.
• Refit the protective cover.
NOTE: Oven bulb replacement is not covered by your guarantee.
Figure 35
B
A
36
Figure 36
BURNERS
They can be removed and washed only with soapy
water. Detergents can be used but must not be
abrasive or corrosive.
Do not use abrasive sponges or pads.
Do not put in dishwasher.
C
After each cleaning, make sure that the
burner-caps, as well as the burners, have
been well wiped off and CORRECTLY
POSITIONED.
It is essential to check that the burner flame
distributor F and the cap C has been correctly
positioned (see fig. 36) - failure to do so can
cause serious problems.
Check that the electrode S (fig. 36) is always
clean to ensure trouble-free sparking.
Check that the probe T (fig. 36) next to each
b u rn e r is a lw a ys cle a n to e n su re co rre ct
operation of the safety valves. Both the probe
and ignition plug must be very carefully cleaned.
F
S
T
Note:
Th e e le ct ro d e S m u st b e ve ry ca re fu lly
clean ed. To avoid damag e to th e electric
ignition do not use it w hen the burners are
not in place.
TRIPLE RING BURNER
The triple ring burner must be correctly positioned (see fig. 37); the burner rib must be
located in position as shown by the arrow.
The burner correctly positioned must not rotate (fig. 38).
Then position the cap A and the ring B (fig. 38).
Figure 37
Figure 38
A
B
37
STORAGE DRAWER
■ The drawer comes out like a normal drawer. A safety catch stops it from sliding
out.
■ The handle is concealed at bottom of front panel.
■ To remove the drawer proceed as per figure 41.
■ To replace the drawer repeat the steps in reverse order.
Figure 39
Figure 41
Note: Do not store
flammable material
in the drawer.
1
Figure 40
4
Handle
Removing the draw er
38
REMOVING THE OVEN
DOOR
Figure 42a
The oven door can easily be removed
as follows:
– Open the door to the full extent (fig.
42a).
– Open the lever A completely on the
left and right hinges (fig. 42b).
– Hold the door as shown in fig. 42.
Figure 42b
– Gently close the door until left and
right hinge levers A are hooked to
part B of the door (fig. 42c)
A
A
– Withdraw the hinge hooks from their
location following arrow C (fig. 42d).
B
– Rest the door on a soft surface.
– To replace the door, repeat the above
steps in reverse order.
Figure 42c
Figure 42d
Figure 42
C
C
39
Figure 43
REMOVING THE INNER
PANE OF GLASS
To clean the inner pane of the oven
door on both sides operate as follows:
– Open the door to the full extent (fig.
43).
– Open the lever A completely on the
left and right hinges (fig. 44).
– Gently close the door (fig. 45) until left
and right hinge levers A are hooked to
part B of the door (fig. 44).
Figure 44
A
– Remove the seal G by unhooking the
no. 3 fixing hooks (fig. 46).
– Gently pull out the inner pane of
glass (Fig. 47).
B
– Clean the glass with an appropriate
cleaner. Dry thoroughly, and place
on a soft surface.
– Now you can also clean the inside of
the outer glass.
Figure 45
Figure 46
Figure 47
G
40
REASSEMBLING THE INNER PANE
Figure 48
To reassemble the inner pane of the
oven door operate as follows:
– Make sure the door is locked open
(see Fig. 45).
D
– Check the correct positioning of the
no. 4 (four) silicon rubbers D (fig. 48).
– Check that you are holding the pane
the correct way. You should be able to
read the wording on it as it faces you.
Figure 49
E
– Insert the inner pane in the left E and
right F side guides (fig. 49) and gen-
tly let it slide up to the retainers H (fig.
50).
F
– Reassemble the seal G in the correct
way (fig. 51) by hooking the no. 3 fix-
ing hooks in the proper holes (fig. 52).
– Open completely the oven door and
close the lever A on the left and right
hinges (fig. 54).
Figure 50
Figure 53
The oven door
has a sealed
gasket in the
top part.
H
Figure 51
It is normal the opened gap between the
top edge of the inner glass and the sealed
g asket. This allow s the cooling air
circulation
Figure 52
Figure 54
G
A
41
Service a n d Ma in t en a n ce
If the ignition spark fails to ignite or does not light the gas, check the following
items before calling our Customer Service Centre to obtain the nearest Authorised
Service Agent:
■ Burner is reassembled and located correctly.
■ Spark electrode and white ceramic are clean and dry.
■ 240 VAC power supply is connected.
Contact the local gas utility or our Customer Service Centre to obtain the nearest
Authorized Service Agent.
■ You can smell gas when all burners are turned on.
■ The burners do not remain alight at the minimum marked setting.
■ The burner flame is yellow or emits an unusual odour.
Note that a bi-annual inspection of the appliance by an authorized service agent
or your locate gas utility will ensure many years of trouble free operation of your
appliance.
42
WIRING DIAGRAM
S1
PR
TM
TMS
F1
1
1a
1a
2a
3a
1
N/7
2
3
4
5
L/8
4a
5a
6a
6
7
7a
8a
8
9a
9
10a
11a
10
11
LF
CF
PA
A
TL
C
CIR
G
S
V
1131797
T
L
N
M
ELECTRIC DIAGRAM KEY
F1
TM
TMS
LF
CF
PR
C
Oven switch
Oven thermostat
Oven thermostat (security)
Oven lamp
Cooling fan
Oven programmer
Top element
G
Grill element
V
Fan
S
Bottom element
Circular element
Ignition switches group
Ignition coil
CIR
PA
A
TL
S1
M
Thermal overload
Thermostat pilot lamp
Terminal block
Earth connection
T
Descriptions and illustrations in this booklet are given as simply indicative. The manufacturer reserves
the right, considering the characteristics of the models described here, at any time and without
notice, to make eventual necessary modifications for their construction or for commercial needs.
43
cod. 1103194 ß2
|