Daewoo SH 9810P User Manual

INSTRUCTION MANUAL  
ENGLISH  
UK  
DVD Player + Video Cassette Recorder  
SH-3510P/SH-9810P/SH-9840P  
SH-3510P  
STANDBY/ON  
VIDEO  
AUDIO  
EJECT  
REC  
SELECT  
STOP  
REW PLAY/PAUSE FF  
OPEN/CLOSE  
AV INPUT  
SH-9810P & SH-9840P  
HELP LINE ; 0 870 100 2525  
Please read this manual carefully before connecting your DVD+VCR and operating it for the first  
time.  
Keep the manual in a safe place for future reference.  
Important Safeguards  
The lightning flash with arrowhead symbol,  
CAUTION  
RISK OF ELECTRIC SHOCK  
within an equilateral triangle, is intended to  
alert the user to the presence of uninsulated  
“dangerous voltage” within the product’s  
enclosure that may be of sufficient magnitude  
to constitute a risk of electric shock.  
DO NOT OPEN  
CAUTION: TO REDUCE THE RISK OF ELECTRIC  
SHOCK, DO NOT REMOVE COVER (OR BACK). NO  
USER-SERVICEABLE PARTS INSIDE. REFER  
SERVICING TO QUALIFIED SERVICE PERSONNEL.  
The exclamation point within an equilateral  
triangle is intended to alert the user to the  
presence of important operating and servicing  
instructions in the literature accompanying the  
appliance.  
WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS  
APPLIANCE TO RAIN OR MOISTURE.  
CAUTION : TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT,  
FULLY INSERT.  
IMPORTANT FOR LASER PRODUCTS  
• LASER : This Digital Video Disc Player employs a Laser System. To ensure proper use of this product  
please read this instruction manual carefully and retain for future reference. Should the unit  
require maintenance, contact an authorized service location - see service procedure.  
Use of control adjustments or the performance of procedures other than those specified  
may result in hazardous radiation exposure.  
To prevent direct exposure to the laser beam, do not try to open the enclosure. Visible laser  
radiation when open and interlocks defeated.  
DO NOT STARE INTO THE BEAM.  
• DANGER : Visible laser radiation when open and interlock failed or  
CLASS 1 LASER PRODUCT  
LUOKAN 1 LASERLAITE  
KLASS 1 LASERAPPARAT  
defeated. Avoid direct exposure to beam.  
• CAUTION : Do not open the top cover. There are no user  
serviceable parts inside the Unit; leave all servicing to  
qualified service personnel.  
This set complies with the EMC Directive 89/336 and with the LVD Directive 73/23.  
CAUTION: Any changes or modification in construction of this device which are not expressly approved by  
the party responsible for compliance could void the user’s authority to operate the equipment.  
• Make sure the unit is placed at least 8cm away from the other home appliances or obstacles in  
order to allow sufficient ventilation around the unit.  
• This unit should not be exposed to drips or splashes and no objects filled with liquids, such as  
vases, should be placed on this unit.  
• Switching it off does not disconnect it from the mains (stand-by). To disconnect it from the  
mains, you have to unplug it.  
• The system is not completely disconnected from the mains when the  
the position.  
/ I button is set to  
1
Important Safeguards  
This set has been designed and manufactured to assure  
personal safety. Improper use can result in electric shock  
or fire hazard. The safeguards incorporated in this unit  
will protect you if you observe the following procedures  
for installation, use and servicing. This unit is fully  
transistorised and does not contain any parts that can be  
repaired by the user.  
surfaces may cause the product and cart  
combination to overturn.  
8
VENTILATION  
Slots and openings in the case are provided for  
ventilation to ensure reliable operation of the unit  
and to protect it from overheating. These openings  
must not be blocked or covered. These openings  
must not be blocked by placing the unit on a bed,  
sofa, rug, or other similar surface. This unit should  
never be placed near or over a radiator or heat  
radiator. This unit should not be placed in a built-in  
installation such as a bookcase or rack unless proper  
ventilation is provided or the manufacturer’s  
instructions have been adhered to.  
1
2
3
READ INSTRUCTIONS  
All the safety and operating instructions should be  
read before the unit is operated.  
RETAIN INSTRUCTIONS  
The safety and operating instructions should be  
retained for future reference.  
HEED WARNINGS  
9
POWER SOURCES  
All warnings on the unit and in the operating  
instructions should be adhered to.  
This unit should be operated only from the type of  
power source indicated on the rating label. If you are  
not sure of the type of power supply to your home,  
consult your dealer or local power company. For  
units intended to operate from battery power, or  
other sources, refer to the operating instructions.  
4
5
6
FOLLOW INSTRUCTIONS  
All operating and use instructions should be  
followed.  
10 MAINS PLUG  
ATTACHMENTS  
We have fitted this unit with a standard mains plug.  
Do not use attachments unless recommended by the  
unit’s manufacturer as they may cause hazards.  
• If the mains lead gets damaged it must be replaced  
by a qualified service agent with an approved lead  
of the same type.  
WATER AND MOISTURE  
Do not use this unit near water- for example, near a  
bath tub, wash bowl, kitchen sink or laundry tub, in  
a wet basement, or near a swimming pool.  
• If the plug is cut off, remove the fuse from the plug  
and get rid of it safely, as if you put it into a supply  
socket it would be dangerous.  
• If you change the plug because the standard plug  
is damaged or unsuitable, please destroy the old  
plug as it would be dangerous if plugged into a  
live power outlet. Follow the wiring instructions  
supplied with the new plug.  
7
ACCESSORIES  
Do not place this unit on an unstable cart, stand,  
tripod, bracket, or table. The  
unit may fall, causing serious  
injury to a child or adult as  
PORTABLE CART WARNING  
(symbol provided by RETAC)  
well as serious damage to the  
unit. Use this unit only with a  
cart, stand , tripod, bracket,  
11 POWER-CORD PROTECTION  
You must make sure the mains lead cannot be  
walked on, crushed, chafed, cut, and so on.  
or table recommended by the manufacturer.  
7A  
12 LIGHTNING  
A unit and cart combination should be moved  
For added protection for this unit during a lightning  
storm, or when the unit is left unattended and  
with care. Quick stops, excessive force, and uneven  
2
Important Safeguards  
unused for long periods of time, unplug it from the  
wall outlet and disconnect the antenna or cable  
system. This will prevent damage to the unit due to  
lightning and power line surges.  
E. If the unit has been dropped or the cabinet has  
been damaged.  
18 REPLACEMENT PARTS  
When replacement parts are required, have the  
service technician verify that the replacements he  
uses have the same safety characteristics as the  
original parts. Use of replacements specified by the  
unit manufacturer.  
13 DISC TRAY  
Keep your fingers well clear of the disc tray as it is  
closing.  
14 OBJECT AND LIQUID ENTRY  
19 SAFETY CHECK  
Never push objects of any kind into this unit  
through openings as they may touch dangerous  
voltage points or “short-out” parts that could result  
in a fire or electric shock. Never spill liquid of any  
kind on the unit.  
Upon completion of any service or repairs to this  
unit, ask the service technician to perform safety  
checks recommended by the manufacturer to  
determine that the unit is in safe operating  
condition.  
15 BURDEN  
20 HEAT  
Do not place a heavy object on or step on the  
product. The object may fall, causing serious  
personal injury and serious damage to the product.  
The product should be situated away from heat  
sources such as radiators, stoves, or other products  
(including amplifiers) that produce heat.  
16 DISC  
21 NORMAL USE  
Do not use a cracked, deformed or repaired disc.  
These discs are easily broken and may cause  
personal injury and product malfunction.  
This product is only designed for household or  
similar general use. Any other use may invalidate  
the guarantee and could be dangerous.  
17 DAMAGE REQUIRING SERVICE  
MAINS FUSE IN THE UK  
Unplug this unit from the wall outlet and refer  
servicing to qualified service personnel under the  
following conditions.  
If you use a 13 amp (BS 1363 type) plug, you must have  
a 3 amp (BS1362 type) fuse fitted. For any other type of  
plug or connection, you must fit a fuse rated between 3  
and 5 amps in the mains plug or adapter, or at the fuse  
box feeding this unit.  
A. When the power-supply cord or plug is  
damaged.  
B. If liquid has been spilled, or objects have fallen  
into the unit.  
EUROPEAN SYMBOLS  
C. If the unit has been exposed to rain or water.  
D. If the unit does not operate normally by  
following the operating instructions. Adjust  
only those controls that are covered by the  
operating instructions. Improper adjustment of  
other controls may result in damage and will  
often require work by a qualified technician to  
restore the unit to its normal operation.  
This unit is double insulated and  
an earth connection is not  
required.  
This unit complies with  
European safety and electrical  
interference directives.  
3
Advantages of This Product Are .....  
• DVD, VCD, CD, CD-R(MP3), CD-RW, VHS  
• Watching DVD and recording broadcasts  
• Integrated remote control (VCR, DVD)  
• VISS function  
Repeat playback (title, chapter, and part for  
DVD/ track, disc, and part for VCD/CD)  
• Selective Play (DVD/VCD/CD)  
You can select and play the desired title / chapter  
of DVD and track of Video CD/CD in STOP mode.  
• 6 languages OSD (On Screen Display)  
function (DVD)  
• Multiplex sound playback/record  
(SH-9810P & SH-9840P only)  
• High Sound Quality of 6 head Hi-Fi  
(SH-9810P & SH-9840P only)  
You can select and display OSD in 6 languages.  
(E / F / S/ G/ I / D)  
• Simple record function  
• MP3 file playback function (CD-R disc having • Parental Lock function (DVD)  
records of MP3 files)  
This function can prevent playback of software  
• GUI (Graphical User Interface) through OSD  
(On Screen Display)  
that may be unsuitable for children.  
• Multi Audio function (DVD)  
By using the [DISPLAY] button on the remote  
control, information on the DVD/VCD/CD player  
and disc, can be displayed on the TV screen.  
• Screensaver function (DVD)  
The audio soundtrack can be heard in up to 8  
languages. In the case of SVCD or VCD, it depends  
on the disc. (The number of audio languages  
depends on the software.)  
• 3D sound (3D sound effect using 2 speakers)  
• High bit / High sampling with 27MHz / 10bit  
video encoder  
• Multi Subtitle function (DVD)  
The subtitle can be seem in up to 32 languages. In  
the case of SVCD or VCD, it depends on the disc.  
(The number of subtitle languages depends on the  
software.)  
• High bit / High sampling with 96MHz / 24bit  
Audio D/A Converter  
• Coaxial, Optical digital Audio output (PCM,  
Dolby Digital, dts)  
• Multi Angle function (DVD)  
This function allows you to choose the viewing  
angle of scenes which were shot from a number of  
different angles. (The number of angles depends  
on the software.)  
You can enjoy high-level digital audio by  
connecting with an amplifier embedded with  
Dolby Digital / dts decoder.  
• Built-in Dolby Digital decoder (DVD)  
• Analog audio 2-channels output for  
DOWNMIX (x1)  
• Screen zoom function (DVD/VCD)  
• Composite video output (x1)  
• Slow Forward / Reverse playback (DVD)  
• Fast Forward / Reverse playback  
• Search of title, chapter, and time in DVD disc,  
and search of time and track time in VCD  
Various TV aspect (DVD)  
4:3 for Pan and Scan, 4:3 for Letter Box, and 16:9 for  
Wide  
4
Read Carefully before Using  
Cautions in use of DVD-Video player are described below.  
Please read carefully before using a DVD-Video player.  
and maintenance every 1,000 hours of use by  
technical engineers.  
• For checking, contact your dealer or your nearest  
service centre.  
Installation place and handling  
• When you place this player near other devices,  
they may affect poorly together.  
Checking and Replacement of Antenna  
• The antenna is subject to change in its direction  
or damage by wind and rain. For a clear picture,  
contact and consult your nearest aerial rigger  
about checking and replacement.  
When you place DVD-Video player above or below  
a TV, it may cause flickering of pictures or failure  
(tape is not ejected).  
• When you place this player near strong magnetic  
materials, it may affect image or voice poorly or  
damage recording.  
Recording important pictures  
Be sure to record the screen and check whether  
recording is performed properly. Bad recordings  
can result if using poor quality tapes.  
Do not spill volatile liquids like insect spray over  
the player. Do not leave rubber or plastic products in  
contact with the player for a long time. They will  
cause deterioration or paint to peel-off.  
Copyright  
• Do not use your recordings without permission  
of a copyrighter except personal usage.  
Not in use  
• When the unit is not in use, be sure to remove the  
disc or tape and turn off the power.  
Tape and Disc Handling  
If you do not use the unit for a long period, remove  
batteries in remote control to prevent leakage.  
Do not use any tape and disc in conditions listed  
below. Damage of video head or cut/coiling of tape  
may cause failure.  
• If you don’t use the unit for a long time, the unit  
may not function properly in the future. Turn on  
and use the player occasionally.  
- Tape with mold  
- Tape or disc stained with juice or food particles  
- Tape having breakage connection  
- Disassembled tape  
Moving  
• Repack the unit as it was originally packed at the  
factory. Alternatively, pack this product with  
towel to prevent transit damage.  
- Disc with severe scratch  
Moisture condensation may occur on tape.  
Moisture condensation damages the tape. Only  
use the tape after the moisture condensation has  
disappeared.  
• Eject any videotape.  
Cleaning  
After use, store tape vertically in a case to  
prevent the tape from becoming loose.  
• Dust off dirt in cabinet or control panel part  
smoothly with a soft cloth.  
• For heavy dirt, soak the cloth in a weak detergent  
solution, wring it well and wipe. Use a dry cloth  
to wipe it out.  
• Follow instructions in using chemical cleaners.  
• Do not use any type of solvent such as gasoline or  
benzene, as they may cause deterioration or paint  
to peel-off.  
• Do not store in the following places.  
- High temperature and humidity  
- Subject to generation of mold  
- Subject to direct sunlight  
- In dirt or dust  
-
Near strong magnetic materials such as a speaker  
Checking  
• The video is a high precision device. To obtain a  
clear picture, we recommend regular inspection  
5
Identification of Controls  
Main body (front panel)  
SH-3510P  
!
@
#
2
4
STANDBY/ON  
VIDEO  
AUDIO  
EJECT  
REC  
SELECT  
STOP  
REW PLAY/PAUSE FF  
OPEN/CLOSE  
AV INPUT  
$
%
^ &  
*
(
)
1
3
5
SH-9810P & SH-9840P  
!
@
#
2
4
$ %  
^ &  
*
(
)
1
3
5
!
POWER (STANDBY/ON) button  
Use to power the device on/off if AC power supply  
is connected.  
1
2
STOP button  
Use to stop playing.  
REWIND button  
@
#
$
%
^
&
*
(
Place to insert videotape  
Disc tray  
Use to rewind currently being played, videotape or  
disc; or to review.  
VIDEO INPUT jack  
AUDIO INPUT jack  
EJECT button  
3
4
Playback/PAUSE button  
Playback videotape or disc.  
Press this button to pause a screen.  
FAST FORWARD button  
RECORD button  
Use to wind currently being played videotape or  
disc; or to playback rapidly.  
Programme Down/Up button  
Operation Display Window  
5
OPEN/CLOSE Tray button  
Display operation of device. For more information,  
see “Operation Display Window” in 7p.  
)
SELECT button  
Use to change DVD mode to VCR mode, and vice  
versa.  
6
Identification of Controls  
Operation Display Window  
- RECORDING MODE -  
- REPEAT MODE -  
[DVD]  
Repeat one chapter  
Timer Recording Standby  
[VCD]  
Repeat track  
[DVD]  
Repeat title  
Repeat ALL  
Timer Recording Error  
Recording in Progress  
[VCD]  
Repeat a defined period  
[DVD, VCD]  
from A  
Repeat a defined period  
Timer Recording in  
Progress  
[DVD, VCD]  
from A to B  
Recording Pause  
- DVD OPERATION -  
- VCR OPERATION -  
DVD playback  
VCR playback  
Fast playback  
Fast forward  
Fast reverse playback  
Slow playback  
Pause picture  
Rewinding  
Fast playback (CUE)  
Fast reverse playback  
(REVIEW)  
Slow playback  
Still picture  
Stop  
Child Lock  
7
Identification of Controls  
Main body (Rear Panel)  
!
@
#$  
^
*
%
&
!
POWER CORD  
^
&
*
Connection to ANTENNA Cable  
Connection to TV  
It is a jack for supplying power to the unit.  
Connect to outlet in a wall.  
EURO AV1 scart socket  
@
#
$
%
EURO AV2/DECODER scart socket  
VIDEO OUTPUT phono socket  
AUDIO OUTPUT phono socket  
DIGITAL OUTPUT (OPTICAL/COAXIAL) Jack  
To enjoy sound quality of theatre level in home,  
connect this jack with amp or unit embedded  
with digital audio decoder.  
8
Identification of Controls  
Accessories  
Instruction  
Manual  
Scart cable  
(supplied only SH-9840P)  
Remote control  
2 Batteries  
RF cable  
• To purchase accessories or not supplied additional parts, contact your nearest dealer or service centre.  
N.B.: Owner’s manual and warranty are not sold additionally.  
Instructions in using REMOTE  
• Operate remote control within 7m from the unit.  
• Do not press 2(two) buttons at the same time.  
• Excessive sun light falling on the remote receiver may cause the remote control to become inoperative.  
• Do not keep in the place with much dust and humidity.  
Remote control battery installation  
Detach the battery cover on the rear of the  
remote control, and insert two AAA  
batteries with the + and - ends aligned  
correctly.  
Two “AAA”  
batteries  
(supplied).  
9
Remote Control  
!
@
#
[DVD] OPEN/CLOSE button, [VCR] EJECT button  
VCR SELECT button  
[DVD, VCR] NUMBER button, [VCR] TRACKING -/+  
button  
$
%
^
SYSTEM button (This button is not available for this set)  
9
!
@
0
SETUP button  
[DVD, VCR] MOVE/SELECT in OSD, [VCR] Channel  
Up/Down button  
&
*
[DVD] TITLE /PBC button  
#
#
[DVD] AUDIO LANGUAGE Select, [VCR] AUDIO Select  
button (SH-9810P& SH-9840P only)  
+
(
)
1
2
[DVD] SUBTITLE Select button  
REVERSE SEARCH button  
PLAY/PAUSE button  
$
%
=
[DVD] PREVIOUS button (move into a previous chapter  
or track)  
^
&
3
4
5
6
7
8
9
0
+
=
Q
q
W
w
E
e
[VCR] Record SPEED button  
[VCR] Record button  
Q
q
W
*
[VCR] TV/VCR button  
[DVD] 3D button  
(
)
w
[VCR] CM SKIP  
E
1
2
e
[VCR] Replay button  
3
R
POWER button  
4
5
r
DVD SELECT button  
[VCR] INPUT Selection button  
CLEAR button  
T
t
6
7
Y
y
8
[DVD, VCR] OSD DISPLAY button  
OK/ENTER button  
[DVD] MENU button  
[DVD] Chapter/Title/Time SEARCH button  
[DVD] ZOOM button  
FORWARD SEARCH button  
STOP button  
Child Lock !  
Press the power [ ] button of the remote for about  
5 seconds. No buttons of front panel can be operated  
[DVD] NEXT button (Move into a next chapter or track) ,  
[VCR] Frame Advance button in pause mode  
now and Lock indicator (“  
”) will be  
displayed on window display. To release child lock,  
press any button on the remote control.  
R
r
T
t
Y
y
[DVD] REPEAT Playback button  
[DVD] REPEAT a defined period from A to B button  
[DVD] ANGLE button  
POWER ON  
[DVD] MARK button  
Player will POWER ON if any button on the  
remote control is pressed.  
[DVD, VCR] PROGRAMME button (SH-9840P only)  
[VCR] LAST CHANNEL button (Return to the previous  
TV channel which was being watched.)  
10  
Setting up your player  
Before you start, unplug all the equipment from the mains supply.  
(Option 1) - Connecting your player through RF lead  
Television  
Aerial  
The type of aerial you  
should use, depends on  
local interference and how  
far you are from the  
200-240V~,  
50/60 Hz  
transmitter. You should  
contact a local retailer if you  
have any questions about  
your aerial.  
Back view of your player  
(Option 2) - Connecting your player through a scart lead  
Television  
Aerial  
200-240V~,  
50/60 Hz  
Scart lead (supplied only  
SH-9840P )  
Back view of your player  
With this connection, if your player is receiving CH BBC1 and your TV is displaying CH3, when you press the  
[TV/VCR] button on the remote control, your TV will automatically display the CH BBC1. “VCR” will be  
shown in the display.  
In this mode, to change the viewing channels the [PR-] and [PR+] buttons on the player remote need to be used.  
To switch off this mode press [TV/VCR] on the remote control, TV remote can now be used as normal. You will  
get better pictures and sound quality if you connect your player using a scart lead.  
11  
Connecting your player through  
extra equipment (satellite system)  
Before you start, unplug all the equipment from the mains supply.  
(Option 1) - Connecting your player through RF lead  
Television  
Aerial  
200-240V~,  
50/60 Hz  
Back view of your player  
Satellite  
You can use this connection if your player has two scart sockets. This will improve sound and picture quality  
when you are recording from satellite.  
12  
Connecting your player to the Hi-Fi system  
Before you start, unplug all the equipment from the mains supply.  
Option 1  
Television  
Aerial  
Hi-Fi  
200-240V~,  
Plug a phono cable into the  
50/60 Hz  
“Audio L/R” sockets on the  
back panel and into the audio  
sockets on any audio  
amplifier, if needed. If your  
player does not have this  
connection, see page 15.  
Player  
You can also use a scart lead to improve picture and sound quality from your player.  
Option 2  
Television  
Aerial  
Hi-Fi  
200-240V~,  
50/60 Hz  
If required, plug a scart to  
phono cable into the “AV1”  
socket on the back panel and  
into the audio socket on any  
audio amplifier.  
Player  
13  
How to connect your player to another player  
Before you start, unplug all the equipment from the mains supply.  
How to connect  
First player  
200-240V~,  
50/60 Hz  
connect a scart lead  
from player to second  
VCR  
Second player  
1) Insert the tape you wish to record on into the first player and press [INPUT] until “AV1” appears on the front  
display.  
2) Insert the tape you wish to copy from into the second player. Press the [PLAY] button on the second player.  
3) Press the [RECORD] button on the first player.  
The player will start recording.  
If your player has two scart sockets, you can use the other socket “AV2” to connect other equipment.  
To use this function, see page 16.  
How to connect your player to a camcorder  
Before you start, unplug all the equipment from the mains supply.  
How to connect  
Television  
Aerial  
Camcorder  
200-240V~,  
50/60 Hz  
to  
camcorder  
Scart Plug to  
TV  
Player  
If you have connected your camcorder in this way, you can also connect a scart lead from “AV2” on the  
back panel of the player to the television. To use this function, see page 16.  
You can also connect the camcorder by using a phono cable if your player has front input sockets.  
Check the front of your player for this connection, see page 16.  
14  
Connecting Dolby Digital Amp with  
Digital Audio Out Jack  
How to connect  
REAR PANEL OF DVD-VIDEO  
CONNECTING CABLE  
(Not supplied)  
(L) AUDIO IN (R)  
Home Theatre Receiver with Dolby Digital decoding capability  
1
Select either COAXIAL or OPTICAL to connect to amp of Dolby Digital.  
** If you want to know about “Dolby Digital”, please refer to [About DVD] in 54-56p.  
Manufactured under license from Dolby Laboratories.  
"Dolby" and the double-D symbol are trademarks of Dolby Laboratories.  
“DTS” and “DTS Digital Out” are trademarks of Digital Theatre Systems, Inc.  
15  
2nd scart socket  
2nd scart socket  
If your video has the AV2 output, shown in the diagram below, you can connect other equipment as seen on  
pages 12-15.  
2nd scart  
INPUT ONLY  
INPUT+OUTPUT  
When connecting other equipment please refer to their manuals for further information. This video manual  
recommends the set up as shown on page 12. If the equipment is turned off when connected by this method, the  
video behaves as normal, but if the equipment is turned on the video will automatically switch over to AV2  
mode and displays the channel of the other equipment, channel selection can only be performed by the other  
equipment, the video PR+/PR- buttons have no effect.  
To return to normal video use the other equipment must be turned off.  
Recording from other Equipment.  
Simple recording can be performed, ensure the equipment is turned on and is displaying the correct channel.  
Timer recording, set the video to perform a timed recording ensuring AV1 is selected as the channel to be  
recorded. Some equipment may have a timer which allows it to be powered on to the correct channel, if this  
feature is not available the other equipment should be left powered on.  
Front AV  
If the video has front input sockets, it is possible to connect devices such as a  
camcorder to the video. To watch a camcorder tape the video must be in  
AVF mode. Recordings of this input are the same as described on page 14.  
16  
Initial Installation  
Switch the TV on.  
You can also start "AUTO SET" in the SETUP "PR PRESET"  
"AUTO SET".  
To tune in new stations (manual tuning) and to enter station names see page 24-25.  
Setting up the player  
You should see this picture the first time you switch on the TV  
and player.  
1
AUTO SET  
OK:CONFIRM  
SETUP:END  
OK for "AUTO SET!".  
"AUTO SET" tunes in all the stations you can receive in your  
country.  
CH 25  
2
3
4
PLEASE WAIT...  
Clock is automatically set.  
SETUP:END  
If other stations are positioned on near the current RF OUTPUT  
CH, the guide message appears automatically.  
RF OUTPUT SET  
CURRENT  
CH 52  
The player recommends the optimal RF OUTPUT CH number  
automatically.  
RECOMMENDED CH 54  
0-9:SELECT(21-69)  
OK:CONFIRM  
SETUP:END  
Press the [OK] button to confirm the recommended PR.  
IMPORTANT!  
Should you wish the stations to have the same numbers as those  
used on the TV, follow the instructions in "Sorting programme  
locations" on page 25.  
PLEASE CHANGE THE TV  
CH TO 54.  
Otherwise ...  
exit the basic installation function and enjoy your player.  
MANUAL SET  
PR01 P-O1 PR08 P-08  
PR02 P-02 PR09 P-09  
PR03 P-03 PR10 P-10  
PR04 P-04 PR11 P-11  
PR05 P-05 PR12 ----  
PR06 P-06 PR13 ----  
PR07 P-07 PR14 ----  
PR+/-:SELECT  
OK:CONFIRM  
SETUP:END  
If you don´t see this picture, because you don´t use a SCART cable,  
search this picture now (CH 52) with the station tuning functions of  
your TV set (see its user manual).  
In case of interference problems on CH 52, type in an  
other transmission channel between 21 and 69 using  
the number buttons.  
17  
Setting time and date  
Setting time and date  
Press [VCR] button on the remote control to change into VCR Mode and follow the procedure  
below.  
Call up the player’s "SETUP" menu,  
choose "VCR SETUP", then "CLOCK SET".  
CLOCK SET  
TIME - - : - -  
1
2
DATE - - / - - /- - - -  
0-9:SETUP (HOUR)  
/:CORRECT SETUP:END  
Move to the position you want to change and type in the  
new values.  
Wait a few seconds after typing a one-digit number.  
CLOCK SET  
TIME 06:05  
DATE 08/08/2004(SUN)  
Store with [OK] button and exit with [SETUP] button.  
0-9:SETUP (HOUR)  
/:CORRECT  
OK:CONFIRM  
SETUP:END  
Auto clock  
Setting Auto clock  
Auto Clock is only available for models with the VPS/PDC function (see page 26).  
Some broadcasting stations may send the time and date along with the VPS/PDC data. The video will  
automatically use this time and date during the initial setting up procedure during normal use, and every  
time you switch the video off at the mains. If you find that this time and date is incorrect you can remove  
this feature by following the steps below changing it to OFF mode, you will then have to manually set the  
time and date, see above.  
VCR SETUP  
AUTO CLOCK  
CLOCK SET  
ON  
OFF  
RF OUTPUT SET  
16:9 SET  
OSD ON/OFF  
AUTO CLOCK  
PR+/-:SELECT  
OK:CONFIRM  
PR+/-:SELECT  
OK:CONFIRM  
SETUP:END  
SETUP:END  
18  
OSD ON & OFF  
OSD (On Screen Display) ON & OFF  
This player is set to “OSD (On Screen Display) ON” mode before shipping and you can change it  
to OFF mode.  
SETUP  
Call up the player’s "SETUP" menu.  
TIMER PROGRAM  
PR PRESET  
1
VCR SETUP  
TAPE CONTROL  
PR+/-:SELECT  
OK:CONFIRM  
SETUP:END  
VCR SETUP  
Choose “VCR SETUP”.  
And press the [OK] button.  
CLOCK SET  
RF OUTPUT SET  
16:9 SET  
2
3
OSD ON/OFF  
AUTO CLOCK  
PR+/-:SELECT  
OK:CONFIRM  
SETUP:END  
Select “OSD ON/OFF”.  
If you want OSD OFF mode, select it and press [OK] button to  
confirm.  
OSD ON/OFF  
ON  
OFF  
Then OSD characters are not displayed in the normal picture.  
PR+/-:SELECT  
OK:CONFIRM  
SETUP:END  
Output Select  
To Select DVD  
Press [DVD] button.  
If DVD mode is correctly selected, DVD is displayed on the operation  
display. Then, REMOTE control works in DVD function.  
To Select VCR  
Press [VCR] button.  
If VCR mode is correctly selected, DVD on the operation display  
window goes out. Then, REMOTE button works as VCR function. Press  
the [VCR] button, then it becomes to the VCR OPERATION mode.  
To Select Operation Mode or External Input  
Press [INPUT] button.  
When you press [INPUT] button, BROADCASTING RECEPTION and EXTERNAL INPUT will be selected.  
But, this button will not function in PLAY, REC and DVD mode.  
19  
DVD Playback  
Press [ ] button to power on.  
Press [DVD] button of REMOTE to select DVD mode.  
1
2
3
Press [OPEN/CLOSE] button to open the disc tray.  
Place a disc firmly on the disc tray, ensuring the disc’s label is uppermost.  
Insert the disc and press [OPEN/CLOSE] button to close the tray.  
The disc tray will close and after initialisation, Playback or Stop function starts  
to operate.  
To play the disc, press [PLAY/PAUSE] button.  
In the case of DVD,  
4
DVD menus and titles are displayed on TV screen.  
In the case of S-VCD and VCD2.0  
the menus are displayed on the TV screen and it is converted into PBC  
(Playback Control) mode.  
In the case of CD, VCD1.1 and MP3,  
the disc plays.  
To stop it, press [ ] button.  
For pause, press [PLAY/PAUSE] button in playback mode.  
If you press this button once more, it starts playback again.  
5
6
Press [OPEN/CLOSE] button to remove the disc.  
Various Playback Methods  
If you want fast forward (cue) or reverse (review) playback, press [] or [œœ]  
button in Playback mode. You can watch fast playing (reverse ) screen.  
* This reverse playback may be unavailable for certain DVD.  
If you want slow (or reverse) playback, press [] or [œœ] button in Pause mode.  
You can watch the desired scene in the slow forward (reverse) playback.  
* In the case of Video CD, this reverse slow playback function is unavailable.  
The  
mark will appear.  
If you want a still picture, press [PAUSE] button in Playback mode. You can watch  
the desired screen in Pause status.  
20  
VCR Playback  
Press [ ] button to power on.  
1
2
3
Press [VCR] button of remote control to change to VCR mode.  
Insert the desired tape.  
If you want to playback, press [PLAY/PAUSE] button.  
When the operational status is flickering, adjust [TRACKING +/-] button.  
To stop it, press [ ] button.  
4
For pause, press [PLAY/PAUSE] button in playback mode.  
If you press this button once more, it starts playback again.  
Press [EJECT] button on the front part of the unit or [OPEN/CLOSE]  
button on remote control to eject the tape.  
5
Various Playback Methods  
If you want fast forward (or reverse) playback, press [] or [œœ] button in  
Playback mode. You can watch fast playing cue/review (rewinding) on screen.  
* NOTE: You might see no colour and a noise band when you fast forward (or  
reverse) playback the tape which is recorded in LP mode.  
If you want Still picture, press [PLAY/PAUSE] in Playback mode. You can watch  
the desired scene in pause status.  
If you want slow-motion playback, press [] button in Pause mode. You can  
watch the desired scene in the slow forward (cue) playback.  
* NOTE: VCR doesn’t have Slow Reverse Playback function.  
If you want to watch a series of screens one by one, (FRAME ADVANCE) press  
[NEXT ] button in Pause mode. Each time you press this button, the picture  
advances by one frame.  
If the product, which  
has a auto-detector,  
detects a contaminated  
head(s), it shows the  
conditions to notice the  
contamination on  
screen.  
If you press [REPLAY] button in playback mode, the player quickly rewinds 15  
seconds of the tape and plays it again.  
If you press [CM SKIP] button in playback mode, the player quickly skips 30  
seconds of the tape and then reverts to play again.  
To Adjust Display  
* In case of the notice  
on screen, please rub  
the heads with a head-  
cleaner followed by  
“How to use a head-  
cleaner”.  
This product includes an automatic Tracking feature and enables users to enjoy clear  
pictures without any additional operation. Provided that the following problems can be  
solved by manual adjustment, which improves display quality. (During automatic  
picture adjustment, “Adjusting Display” is displayed on TV screen.)  
- If the picture is poor in Playback mode,  
-
If noises occur in the upper or lower part of the picture in slow playback (cue) mode,  
- If paused picture vibrates up and down.  
Use [TRACKING +/-] buttons of remote control to adjust the display for optimum  
viewing.  
21  
Recording  
To Record With VCR  
Press [ ] button to power on.  
1
• Press [VCR] button of remote control to change to VCR mode.  
Insert a recordable tape.  
Insert a tape with recording tab.  
2
3
With [CHANNEL], [NUMBER] and [INPUT] buttons, select the desired  
broadcasting channel or external input unit to be recorded.  
Select the desired speed (SP or LP) with [SPEED] button.  
4
5
6
Press [REC] button.  
Then, it starts recording.  
If you want to pause recording, press [PAUSE] button.  
After pressing [PAUSE] button, if the pause status continues for five minutes, it  
will be released and the recordings will continue automatically.  
To exit recording, press [STOP] button.  
7
To Enjoy a TV Channel or DVD during recording  
1
2
If you want to playback DVD during recording with video, insert a DVD disc.  
Place the desired DVD disc on DVD tray, press [DVD] button to convert OUTPUT  
into DVD mode and press [PLAY] button. Then, you can watch DVD.  
If you want to watch a TV channel during DVD recording with video, press  
[VCR] button to convert OUTPUT into VCR mode and press [PR+/-] button.  
Then , you can watch a TV channel.  
22  
Recording  
To Copy From DVD To Videotape  
1
Insert the desired DVD disc.  
When the DVD disc is copyright protected, you can’t copy it. If DVD disc is not  
copy protected then insert a blank tape.  
2
3
Press [REC] button during playing of DVD.  
DVD plays and VCR starts recording.  
If you press STOP [ ] button in DVD mode, DVD and VCR will stop at the  
same time.  
If you press STOP [ ] button in VCR mode, VCR stops to record and DVD  
continues to play.  
“This product incorporates copyright protection technology that is protected by  
U.S patents and other intellectual property rights.  
Use of this copyright protection technology must be authorized by Macrovision,  
and is intended for home and other limited viewing uses only unless otherwise  
authorized by Macrovision. Reverse engineering or disassembly is prohibited.”  
One Touch timer Recording (OTR)  
If you need to make an instant recording, or you want to record the current TV programme for a pre-  
determined time , follow the procedures below.  
1
2
First, follow the steps 1 to 4 in “Recording With VCR”.  
Press [REC] button reference the “Recording Times Table” below.  
Once  
Twice  
continuous recording until you press STOP button  
recording for 30 mins from current time  
3 (times) recording for 1 hour  
Incrementing recording for 30 mins at each press.  
21  
22  
recording for 10 hours  
returning to the status of Once Press  
3
To stop Recording mode, press [STOP] button more than 5 seconds.  
23  
Tuning in New Stations  
The TV and player are switched on.  
To see the picture from your player, press the input or AV (Audio/Video) button on the TV.  
Tuning  
PR PRESET  
To complete the set-up of your video recorder when the  
AUTO SET  
auto set has not stored all of the channels or when you wish  
MANUAL SET  
PR ERASE  
PR ALIGN  
1
to store a new channel.  
Call up the video’s "SETUP" menu, choose "PR PRESET".  
PR+/-:SELECT  
OK:CONFIRM  
SETUP:END  
Select "MANUAL SET".  
MANUAL SET  
PR01 P-O1 PR08 P-08  
PR02 P-02 PR09 P-09  
PR03 P-03 PR10 P-10  
PR04 P-04 PR11 P-11  
PR05 P-05 PR12 ----  
PR06 P-06 PR13 ----  
PR07 P-07 PR14 ----  
2
3
4
PR+/-:SELECT  
OK:CONFIRM  
SETUP:END  
Choose any unused programme number "----" or "P-xx" ...  
MANUAL SET  
PR  
04  
RECEPTION  
AERIAL  
It's best to use the same programme number on both the TV  
and video.  
AUTOSEARCH CH_ _  
FINE TUNING  
DECODER  
NAME  
ON  
_ _ _ _  
PR+/-: UP/DOWN  
/: SELECT  
... and confirm by selecting “OK” button.  
OK:CONFIRM  
SETUP:END  
MANUAL SET  
Set the station you want:  
• the programme number;  
• the broadcast system you want (Aerial(CH) or  
Cable(CC)),  
• You can directly enter the real channel number with the  
PR  
03  
RECEPTION  
AERIAL  
AUTOSEARCH CH 03  
FINE TUNING  
DECODER  
ON  
NAME  
_ _ _ _  
PR+/-: UP/DOWN  
/: SELECT  
OK:CONFIRM  
SETUP:END  
[0 to 9] buttons, or search by pressing [œ/],  
• The fine tuning you can adjust,  
• When the programme is encoded (and you have a  
decoder connected to socket EURO AV2), press the [œ or  
] to select ON or OFF.  
• Change or create the station name.  
MANUAL SET  
Once you see the station you want, store it by selecting OK.  
PR  
03  
RECEPTION  
AERIAL  
AUTOSEARCH CH_ _  
FINE TUNING  
DECODER  
NAME  
5
Tune in further stations (from step 3 onwards) or exit  
tuning mode.  
ON  
_ _ _ _  
PR+/-: UP/DOWN  
0/1: CHANGE/CREATE  
OK:CONFIRM  
SETUP:END  
24  
Tuning in New Stations  
Station names  
If your player is showing no station name or is showing a station name incorrectly, you can correct  
this.  
MANUAL SET  
Call up this menu (see the previous page),  
if it isn't displayed.  
PR  
01  
RECEPTION  
AERIAL  
AUTOSEARCH CH01  
FINE TUNING  
1
Select NAME position.  
Press the [0] button to change the given name.  
Or press the [1] button to create the station name.  
DECODER  
ON  
_ _ _ _  
NAME  
PR+/-: UP/DOWN  
0/1: CHANGE/CREATE  
OK:CONFIRM  
SETUP:END  
MANUAL SET  
01  
Either select the name from the stored list or  
create the station name by entering 4 letters/digits.  
Change the letters with the [PR +/–] buttons,  
PR  
RECEPTION  
AERIAL  
AUTOSEARCH CH_ _  
FINE TUNING  
2
3
DECODER  
NAME  
ON  
O
_ _ _  
move to the next letter with the [œ/] buttons.  
PR+/-: SELECT CHARACTER  
/: SELECT POSITION  
OK:CONFIRM  
SETUP:END  
MANUAL SET  
PR01 BBC1 PR08 SKYS  
PR02 BBC2 PR09 MTVE  
Store and exit.  
PR03 ITV  
PR10 P-10  
PR04 CHA4 PR11 P-11  
PR05 SKY1 PR12 ----  
PR06 SKYN PR13 ----  
PR07 SKYM PR14 ----  
PR+/-:SELECT  
OK:CONFIRM  
SETUP:END  
Sorting programme locations  
If the location numbers used for programmes stored in your TV and player are different, you can change them on  
the player. To do this, move the stations to the right numbers, until they are arranged the way you want.  
PR ALIGN  
PR01 BBC1 PR08 SKYS  
1
2
Call up the player’s "SETUP" menu,  
choose "PR PRESET" then "PR ALIGN".  
PR02 BBC2 PR09 MTVE  
PR03 ITV  
PR10 P-10  
PR04 CHA4 PR11 P-11  
PR05 SKY1 PR12 ----  
PR06 SKYN PR13 ----  
PR07 SKYM PR14 ----  
Select the programme to swap.  
PR+/-:ALIGN  
:PR VIEW  
OK:CONFIRM  
SETUP:END  
Confirm by pressing OK button.  
Move the station to the desired location number.  
Confirm by pressing OK button.  
Clearing programme locations  
PR ERASE  
PR01 BBC1 PR08 SKYS  
PR02 BBC2 PR09 MTVE  
1
2
Call up the player’s "SETUP" menu,  
choose "PR PRESET" then "PR ERASE".  
PR03 ITV  
PR10 P-10  
PR04 CHA4 PR11 P-11  
PR05 SKY1 PR12 ----  
PR06 SKYN PR13 ----  
PR07 SKYM PR14 ----  
Select the station (location number) you want to clear.  
PR+/-:SELECT  
:PR VIEW  
OK:ERASE  
Review the picture by pressing [œ] button.  
SETUP:END  
Clear by pressing OK button.  
25  
Timer Recording  
For timer recordings, clock, date, and stations must be set correctly.  
Load a cassette with its safety tab in place and with sufficient free space for the recording.  
Timer recording using VideoPlus (SH-9840P only)  
Call up the VideoPlus menu by pressing PROGRAM on the  
remote control.  
VIDEOPLUS  
83077----  
From your TV magazine, type in the number next to the  
programme you want to record ...  
1
0-9:VIDEOPLUS NUMBER  
:CORRECT  
OK:CONFIRM  
SETUP:END  
... and confirm.  
HOW OFTEN DO YOU WANT  
TO RECORD THIS PROGRAM?  
Decide if you want to record "ONCE", "WEEKLY" or "DAILY"...  
... and confirm.  
ONCE  
WEEKLY(ONCE A WEEK)  
DAILY(MON-FRI)  
DAILY(MON-SAT)  
DAILY(MON-SUN)  
2
3
PR+/-:SELECT  
OK:CONFIRM  
SETUP:END  
If you wish to make changes:  
TIMER PROGRAM (ONCE)  
03  
PR  
Move to the position you want to change using the [  
buttons.  
/
œ ]  
START TIME  
END TIME  
21:20  
22:20  
14/08(SAT)  
SP  
START DATE  
TAPE SPEED  
VPS/PDC  
ON  
Change the setting using the [  
setting are ok, press [OK], till you see “OK: CONFIRM” in the  
bottom line.  
Confirm.  
/
] or [number] buttons. If all  
PR+/-:SELECT (AV1/AV2)  
0-9 : SETUP (PR)  
/:CORRECT  
OK:CONFIRM  
SETUP:END  
Switch your player off.  
VPS/PDC is a service provided by some stations to enable you to perform timer recordings  
precisely even if the broadcaster delays the start time of the programme slightly. The time you enter  
is the VPS/PDC time so must be correct. Not all stations offer VPS/PDC, in which case the player  
will start at the time you enter and not the actual start time of the programme.  
If you wish to start recording at a specific time without it being adjusted by the VPS/PDC system  
in the event of a delay, switch VPS/PDC off otherwise the player will not record at the preset time.  
• If you don’t have the VIDEOPLUS numbers see next page for the normal timer operation.  
• If you have made a mistake, move back to the relevant position with the [ ] button and change  
the setting.  
œ
• If there is no programme location displayed under “PR” in the change menu, the player doesn’t  
yet know the location number for the programme you want. Type it in and this will be stored  
for last recordings.  
• If you wish to record from a satellite receiver, select under “PR” the satellite programme  
location or AV (1/2) (depending on the connection with the antenna cable or the SCART-cable).  
Leave the satellite tuner turned on and switched to the programme you want.  
• Should programming overlap, you get a warning.  
• To cancel the recording press the  
button (stop) for more than 5 seconds.  
• VIDEOPLUS is a trademark applied for by Gemstar Development Corp.. The VIDEOPLUS  
system is manufactured under license from Gemstar Development Corporation.  
26  
Timer Recording  
For timer recordings, clock, date, and stations must be set correctly.  
Load a cassette with its safety tab in place and with sufficient free space for the recording.  
Normal timer recording  
HOW OFTEN DO YOU WANT  
Call up the player’s "SETUP" menu and, choose "TIMER  
PROGRAM".  
Decide if you want to record "ONCE", "WEEKLY" or  
"DAILY"...  
TO RECORD THIS PROGRAM?  
ONCE  
WEEKLY(ONCE A WEEK)  
DAILY(MON-FRI)  
DAILY(MON-SAT)  
DAILY(MON-SUN)  
1
2
PR+/-:SELECT  
OK:CONFIRM  
... and confirm.  
SETUP:END  
Type in one after the other:  
• The programme location number;  
• the time the broadcast starts,  
TIMER PROGRAM (ONCE)  
PR  
--  
START TIME  
END TIME  
START DATE  
TAPE SPEED  
VPS/PDC  
--:--  
--:--  
--/--  
SP  
• the time the broadcast ends,  
ON  
• the day of the broadcast, if it is not today.  
• Select LP if you wish to make a long play recording .  
• Switch off VPS/PDC here if you need to .  
PR+/-:SELECT(AV1/AV2)  
0-9 :SETUP(PR)  
/:CORRECT SETUP:END  
If you wish to make changes:  
TIMER PROGRAM (ONCE)  
PR  
01  
Move to the position you want to change using the  
buttons. Change the setting using the [PR+/- ] or [number]  
buttons.  
[ /  
œ ]  
START TIME  
END TIME  
START DATE  
TAPE SPEED  
VPS/PDC  
18:10  
20:30  
20/08(FRI)  
LP  
3
ON  
PR+/-:SELECT(AV1/AV2)  
If all settings are ok, press [  
CONFIRM” in the bottom line.  
Confirm.  
œ
or ], till you see “OK :  
0-9 : SETUP (PR)  
/:CORRECT  
OK:CONFIRM  
SETUP:END  
Switch your player off.  
Wait a few seconds after typing a one-digit-number.  
If you have made a mistake, move to the position you want to change using the [  
and change the setting.  
/
œ ] buttons  
If programme timings overlap, the machine will give a warning message. If you don’t adjust  
the times, the machine will record the first programme completely then continue with the  
second one.  
If there is no sufficient free space for the recording on the cassette the video switches  
automatically to “LP” for double recording capacity.  
The recorder will eject cassettes which have the safety tab removed.  
• The player will be powered on and record the program at the set time.  
• If the player is powered on after a timer recording has been set, the player cannot record in  
VCR mode but can record in DVD mode.  
27  
Timer Recording  
Timer Review – changing and erasing  
TIMER PROGRAM  
START END DATE  
Call up the player’s "SETUP" menu,  
choose "TIMER PROGRAM".  
PR  
03  
01  
--  
21:20 22:20 14/08  
18:10 20:30 20/08  
-- : -- -- : -- -- / --  
-- : -- -- : -- -- / --  
-- : -- -- : -- -- / --  
-- : -- -- : -- -- / --  
-- : -- -- : -- -- / --  
-- : -- -- : -- -- / --  
--  
--  
1
--  
--  
--  
PR+/-:SELECT  
OK:CONFIRM  
SETUP:END  
TIMER PROGRAM (ONCE)  
03  
Select the programming you wish to change or  
erase.  
If you want to erase this programming press  
button [0], confirm with OK.  
If you wish to make changes:  
PR  
START TIME  
END TIME  
21:20  
22:20  
14/08(SAT)  
SP  
START DATE  
TAPE SPEED  
VPS/PDC  
2
ON  
0 :ERASE  
/:CORRECT SETUP:END  
Move to the position you want to change using the  
[ /  
œ ] buttons.  
Change the settings using the [PR +/–] or  
[number] buttons.  
If all settings are ok, press [  
œ
or ], until you see  
"OK: CONFIRM" in the bottom line.  
Confirm changes with [OK]. Exit the menus.  
28  
More Functions  
The counter counts in real time from the point you load the cassette. This does not have to be its  
beginning! The counter does not count unrecorded parts of the tape.  
If you rewind beyond the zero position, the counter counts in negative values (e.g. – 0:01:15).  
Clock / counter display  
STOP SP  
PR01 BBC1  
STEREO ON  
Each time you press [DISPLAY] button,  
1x: Time and date+current status Time and date  
counter  
2x: Counter+current status  
3x: disappear.  
14:00 08/08  
V
E180 00:48  
If the tape is not wound (PLAY, FF, REW,...), the tape remaining time does not appear.  
If the timer recording information is contained within the received broadcast signal , press the button to  
display the VPS/PDC icon within the received broadcast signal.  
Remaining time and cassette length  
Call up the player’s "SETUP"  
menu,choose "TAPE CONTROL".  
TAPE CONTROL  
TAPE REMAIN  
TAPE REMAIN  
GO TO ZERO  
COUNTER RESET  
INDEX+  
E-180  
E-240  
E-300  
• Remaining time display is only  
possible when the cassette is  
loaded.  
INDEX-  
PR+/-:SELECT  
OK:CONFIRM  
PR+/-:SELECT  
E-240 01:27  
SETUP:END  
OK:CONFIRM  
SETUP:END  
When you want the player to show the time remaining from the current player tape position (to find out if  
there is sufficient space for a recording, for example).  
To ensure the remaining time shown is accurate, select from the list given in the menu the cassette tape  
length currently being used.  
Searching a recorded programme with index  
When you record a programme, the VCR places an index mark at the start  
of the recording.  
To search fo an index mark  
1. Call up the player’s "SETUP" menu, choose "TAPE CONTROL"  
2. Choose index + to search forward or index - to search backward.  
The VCR will locate your index mark and begin playback.  
TAPE CONTROL  
TAPE REMAIN  
GO TO ZERO  
COUNTER RESET  
INDEX+  
INDEX-  
PR+/- :SELECT  
OK:CONFIRM  
SETUP:END  
29  
More Functions  
Accessing counter zero position  
REW SP  
GO TO ZERO  
The player will wind to the position 0:00:00 and stop.  
0:02:13  
Resetting the counter to zero  
COUNTER RESET  
Reset the counter.  
0:00:00  
16 : 9 Wide Screen Format Playing back / Recording  
VCR SETUP  
Using this player you can play and record programmes having 16:9 Wide-Screen  
format.  
CLOCK SET  
RF OUTPUT SET  
16:9 SET  
OSD ON/OFF  
AUTO CLOCK  
• 16:9 Set  
PR+/-:SELECT  
OK:CONFIRM  
-Auto : This video automatically detects the programme format (16:9 or 4:3) and  
records or plays this programme in the same format.  
SETUP:END  
-ON : The video will play or record all broadcasts in 16:9 format. 4:3 broadcasts will  
be converted to 16:9 format.  
16:9 SET  
-OFF : The video will play or record all broadcasts in 4:3 format only.  
AUTO  
OFF  
ON  
If you watch a programme which is recorded in 16:9 wide screen format with  
this player, your TV must have 16:9 wide screen function and you have to  
connect the TV and player with the A/V scart cable.  
PR+/-:SELECT  
OK:CONFIRM  
SETUP:END  
AUTO REPEAT  
If you press the [PLAY] button for 5secs during stop or still mode, Auto repeat mode is engaged. This player  
then repeatedly plays the tape from beginning to end.  
To release this mode, press the [ ] button or mode operation button. (PLAY, FF, REW or STOP)  
30  
More Functions  
Child lock  
Press the [ ] button for about 5 seconds.  
No buttons on the front panel can be operated now and LOCK INDICATOR  
(“  
”) will be displayed on the window display. Keep your remote control in a  
safe place.  
To release child lock, press any button on the remote control.  
Cassettes  
Use only good quality tape cassettes with the VHS logo.  
PAL  
•Keep cassettes away from excessive moisture or dust, magnetic and electrical fields  
(loud speakers and computer monitors, for example).  
•Always wind the tape to the beginning when you have finished. Store with the full  
spool at the bottom and with the cassette in its cover.  
You can protect your precious recordings from being wiped by breaking out the safety  
tab on the back of the cassette (some cassettes have a slide). Should you wish to re-use  
the tape after removing the tab, cover the hole with adhesive tape.  
and ...  
Dimmer : Your player dims its display when switched to stand-by mode.  
Auto power off : Your player switches to stand-by after 5 minutes, if no tape is played and no tuning signal is  
received.  
31  
More Functions  
The player records the complete sound signal transmitted by the TV station.  
On the mono VCR, you will hear the normal mono sound.  
The Hi-Fi system (SH-9810P &SH-9840P only)  
In addition to the normal mono sound track of VHS video recorders, your player is equipped with a high-  
quality Hi-Fi sound system.  
This means you can enjoy  
• films with excellent stereo sound  
• films of full-length concerts in high quality stereo  
• films with impressive Surround Sound using additional Surround equipment  
• films with two dialogue modes (dual, bilingual), usually the original sound track and dubbed sound track  
• VHS cassettes with Hi-Fi stereo sound and VHS cassette with normal sound  
What you can listen to (SH-9810P &SH-9840P only)  
STOP SP  
PR10 EURO  
STEREO ON  
During Stop, the player displays what the current station is broadcasting. When  
you switch to another station or the current station changes the sound mode, your  
player displays the programme and sound mode on screen (if not, press AUDIO).  
• “STEREO” = stereo  
“BIL I / BIL II ”=bilingual  
nothing= monaural sound  
PLAY  
SP  
Hi-Fi  
L+R  
During Playback, the player displays what is recorded on  
the cassette (if not, press AUDIO).  
• “Hi-Fi” = stereo/bilingual  
nothing = monaural sound  
Choice of sound output (SH-9810P &SH-9840P only)  
During a stereo performance (playback-”Hi-Fi”/ broadcast  
- “STEREO”):  
Hi-Fi stereo ✔✔ left audio channel only right channel  
only the normal mono sound track of a Hi-Fi cassette  
PLAY  
SP  
Hi-Fi  
L+R  
HI-Fi  
LEFT  
Hi-Fi  
RIGHT  
Hi-Fi  
OFF  
• During broadcasting a bilingual performance : Main  
STOP SP  
PR10 EURO  
BIL  
language (original sound track)  
sub-language  
BIL  
I
II  
(dubbed)  
OFF.  
both main language and sub-language  
BIL  
I+II  
BIL  
OFF  
• For mono performances , there is no choice available.  
32  
Connections and Copying  
If you are using a SCART cable, select the AV input on the TV to see the picture from the player.  
If you are not using a SCART cable, select the programme number on the TV reserved for video  
input to see the picture from the player.  
To the TV via antenna cable (if you are not using a SCART cable)  
If you are not using a SCART cable, your player can transmit pictures and sound to the TV via the coax aerial  
cable. Just tune the TV to the player's transmitting channel (factory set to UHF CH 52). Tune the TV carefully to  
ensure the best pictures and sound.  
Once you have carried out the steps in "Connecting up the player" , switch  
on your TV.  
1
Press the [ENTER] button of the player’s remote control for longer than 5  
seconds to call up the player´s test signal.  
Tune the TV to the test signal using the channel pre-set functions of your  
TV as described in its manual.  
When you have found the test signal, store it under the channel number  
on your TV for player input.  
Press the [ENTER] button of the player’s remote control again for longer  
than 5 seconds to remove the test signal.  
• If the quality of the test signal transmitted to the TV is poor due to  
interference caused by a station transmitting on channel 52, you can tune  
RF OUTPUT SET  
2
the player to a different transmitting channel. Find a free channel  
between 21 and 69 on your TV.  
CH  
52  
Call up the player’s "SETUP" menu, choose "VCR SETUP" then "RF  
OUTPUT SET".  
0-9:SELECT (21-69)  
OK:CONFIRM SETUP:END  
Type in the free channel.  
Store and exit.  
If the quality of the test signal transmitted to the TV is poor, fine-tuning on the TV may help  
(refer to the TV manual).  
Without a scart cable, you will not get stereo sound from a TV capable of stereo sound.  
33  
Connections and Copying  
Switch off all components when connecting or disconnecting cables.  
Copying  
To copy to your player from another video  
machine, connect the two machines with a cable  
between their EURO AV (SCART) sockets and  
select as programme "AV 1/AV 2" or “F. AV”  
(front sockets) using the [AV], [PR+/-] or [INPUT]  
button.  
Other VCR  
Decoder for Pay-TV  
Camcorder  
Video Player  
Satellite Receiver  
Set the other video machine to playback and your  
machine to record.  
•To connect a mono audio source, use the front  
Audio In socket marked L.  
To copy to another video machine from your  
player, connect the two machines by means of  
their EURO AV (SCART) sockets.  
On the other video, select its AV input and set the  
machine to record.  
Switch your player to play back at the position you  
want copying to start.  
Audio Amp.  
devices  
TV  
(other VCR)  
Assembling  
Should you wish to assemble your own film, from camcorder footage for example, use the assembly technique  
for smooth edit points:  
The symbol is lit in VCR mode and goes out in TV  
mode.  
This symbol means the cassette is in.  
This symbol means a timer recording is setting.  
For the best results, the source cassette from which  
you are recording should already be playing back  
when you start recording.  
34  
Playing a desired scene  
To skip scenes in a disc  
To move to next chapter (or track), press [NEXT] button.  
The current chapter (or track) moves to the next chapter (or track).  
Press [œœ PREV] button.  
The current scene moves to the previous chapter (or track) or first scene of current  
chapter (or track).  
Moving directly to a desired title  
Some movie discs may contain multiple titles. If the disc has a movie title menu recorded on it, the [TITLE/PBC] or  
[MENU] button can be used to select the movie title. Details of operation may differ depending on the disc used.  
* Selecting a title may not be available on certain DVD discs.  
Press the [TITLE/PBC] or [MENU] button.  
A list of the titles on the disc is displayed.  
1
* For the case of VCD disc, menu screen will  
appear only when the disc has PBC function  
and PBC ON is activated.  
Press the [ENTER] button or [PLAY] button  
after pressing the [œ √…†] button to select  
the desired title.  
2
For the case of VCD disc, press the [Number]  
button.  
The selected title now starts playing.  
35  
Playing a desired scene  
Repeating a defined period  
Each time you press [REPEAT] button in playback mode, repeat playback starts as below.  
- DVD -  
- VCD -  
- CD/MP3 -  
Repeat one  
CHAPTER  
TRACK  
Repeat all  
Random  
OFF  
TITLE  
OFF  
ALL  
OFF  
CHAPTER : Current chapter will play repeatedly.  
TITLE : Current title will play repeatedly.  
TRACK : Current track will play repeatedly.  
ALL : Current disc will play repeatedly.  
• Repeat one : Current file will play repeatedly.  
• Repeat all : All files on the disc will play repeatedly.  
• Random : Tracks on the disc will play in random order.  
OFF : Repeat playback will be cancelled.  
* For the case of VCD disc, repeat playback starts only in PBC OFF mode.  
Repeating a defined period from A to B  
You may repeat a defined period from A to B.  
At the point where you want to start the repeat  
playback period, press [A-B] button.  
A-  
A MP3 disc may  
not be repeated  
from A to B.  
1
2
The figure shown on the right appears and the repeat  
playback start position (A) is set.  
At the point where you want to end the repeat  
playback, press [A-B] button again.  
A-B  
The repeat playback end position (B) is set and the  
repeat playback period from A-B is defined.  
To exit from repeat playback mode, press [A-B] button.  
OFF  
Repeat playback mode is cancelled and Normal Playback  
mode is resumed.  
3
36  
Playing a desired scene  
Searching DVD with a title number, a chapter number or a time  
current title  
number  
If you want to search with a title number, press  
[SEARCH] button one time.  
1
001/003  
It shows current and total title numbers. Please enter  
the new title number to be searched using the  
[NUMBER] buttons.  
total title  
number  
current chapter  
number  
If you want to search with a chapter number,  
press [SEARCH] button twice.  
2
3
It shows current and total chapter numbers.  
Please enter the new chapter number to be searched  
using the [NUMBER] buttons.  
001/023  
total chapter  
number  
If you want to search with a time, press  
[SEARCH] button three times.  
01:03:20  
current time  
Please enter the new time to be searched using the  
[NUMBER] buttons.  
After completing the enteries, please press  
[ENTER] button.  
PLAY starts from the selected position.  
37  
Playing a desired scene  
Searching VCD with a track or track time  
If you want to search with a track number, press  
[SEARCH] button once.  
current track  
number  
1
If PBC is OFF, the screen like the figure to the right  
001/013  
appears. It shows current and total track  
numbers. Please enter the new track number to  
be searched using the [NUMBER] button.  
total track  
number  
* If PBC is ON, pressing track number converts PBC to  
OFF mode automatically.  
If you want to search with a track time, press  
[SEARCH] button twice.  
01:03:20  
2
If PBC is OFF, the screen like the figure to the right  
appears.  
current time  
It shows total track time.  
Please enter the new time to be searched using the  
[NUMBER] button.  
After completing the enteries, please press  
[ENTER].  
3
PLAY starts from the selected position.  
Storing markers in memory to be viewed (listened to) again  
Storing a MARKER in the DVD memory is similar to marking your page in a book. It allows you to  
quickly return to any point on the disc.  
Storing a marker in the memory.  
1 - - - - - - - -  
Press [MARK] during play and press  
1
[PROGRAM] at the starting point of the section  
to be viewed (listened to) again.  
Recalling/ Clearing a marker  
Press [MARK] during playback. Press [œ √] to select the marker to be  
recalled/cleared.  
2
Press [ENTER] to recall a marker. Or press [CLEAR] to clear a marker.  
Play resumes from the point corresponding to the selected marker, or the  
selected marker is cleared.  
38  
Confirming the current PLAY mode on screen  
Confirming the current DVD disc mode  
While in playing, press [DISPLAY] button.  
It shows the current disc mode.  
If you want to change the mode, select the item with up/down (…†) cursor and enter  
the new settings with [number], [œ] or [] button. After completing the enteries, press  
[ENTER] button.  
To exit from Display mode, press [DISPLAY] button again.  
current title / total title  
current chapter / total chapter  
time elapsed  
subtitle selected / current subtitle / total subtitle  
audio language selected / current / total audio language  
repeat playback mode  
001/003  
001/023  
00:01:03  
ENG 01/01  
ENG 01/03  
OFF  
current angle / total angle  
01/01  
0-9  
39  
Confirming the current PLAY mode on screen  
Confirming the current VCD disc mode  
While in playing, press [DISPLAY] button.  
It shows the current disc mode.  
If you want to change the mode, select the item with up/down (…†) cursor and enter  
the new settings with [number], [œ] or [] button. After completing the enteries, press  
[ENTER] button.  
To exit from Display mode, press [DISPLAY] button again.  
001/003  
00:01:03  
OFF  
current track / total track number  
time elapsed  
repeat playback mode  
PBC mode  
ON  
0-9  
Confirming the current CD, MP3, JPG, MPG disc mode  
It shows the current disc mode.  
If you want to change the mode, select the item with up/down (…†) cursor and enter  
the new settings with [number], [œ] or [] button. After completing the enteries, press  
[ENTER] button.  
MUSIC  
000/000 0:00:00 / 0:00:00  
disc mode / current playback file name  
current track / total track number,  
time elapsed / total time, repeat playback mode  
MUSIC file select  
JPG file select  
LIST PROGRAM  
max 6  
SKY  
MPG file select  
winamp  
_ _ _ _  
_ _ _  
_ _ _ _ _  
_ _ _  
_ _ _ _ _  
\
current cursor file name  
* For more information, refer to 43-46p.  
40  
Selecting an AUDIO language,  
SUBTITLE language and 3D AUDIO  
Selecting an audio language  
The user may select an audio language and subtitle language if a disc includes Multi-language.  
Keep pressing [AUDIO] button till the user’s preferred language appears in  
A certain disc  
playback mode.  
may not support audio  
select or subtitle select.  
If DVD disc includes audio information, every time the user presses [AUDIO] button,  
English (ENG), French (FRE), Spanish (SPA) and others appear sequentially.  
ENG 01/03  
Selecting a subtitle language  
Keep pressing [SUBTITLE] button till the user’s preferred language appears in  
playback mode.  
If a DVD disc includes subtitle information, every time the user presses [SUBTITLE]  
button, English (ENG), French (FRE), Spanish (SPA), ... and OFF appear sequentially.  
ENG 01/01  
Selecting 3D Audio  
You can enjoy a virtual 3D sound effect from 2-channel sources.  
Press [3D].  
ON  
Every time you press [3D], the 3D sound toggles  
between 3D ON › 3D OFF.  
OFF  
41  
Selecting ZOOM and Multi Angle  
Using a zoom function  
The user can enlarge the current screen about 2 or 4 times.  
Keep pressing [ZOOM] button till the preferred zoom appears.  
Every time the user presses [ZOOM] button, the zoom magnification changes 2 times  
• During zoom mode,  
subtitle language  
can’t be seen.  
(X2)  
4 times (X4)  
OFF  
2 times (X2)  
... in sequence.  
A base area to be enlarged is centralised and the area can be changed with the operation  
of the [œ √…†] buttons.  
x2  
x4  
Different Angle  
If a disc includes multi angle information, the user can watch a screen in multi angles. The function is limited  
to a DVD disc supporting multi angle information.  
Keep pressing [ANGLE] button till the preferred  
01/01  
angle appears.  
Every time the user presses [ANGLE] button, the  
angle changes by degrees in consecutive order.  
42  
About MP3, CDDA, JPG and MPG discs  
Playing a disc containing MP3 or CDDA files  
This unit will play MP3 or CDDA files recorded on CD-R and CD-RW discs.  
Turn on your television and select the channel assigned to this DVD player.  
Press the DVD open [OPEN/CLOSE] button, the disc tray opens.  
1
Put a MP3 or CDDA disc on the disc tray with the label side up.  
Press the DVD open [OPEN/CLOSE] button, the disc tray closes.  
The unit will take a short while to load the disc and display the directory structure.  
The figure shown below appears.  
MUSIC  
000/000 0:00:00 / 0:00:00  
2
LIST  
PROGRAM  
max 6  
SKY  
winamp  
_ _ _ _  
_ _ _  
_ _ _ _ _  
_ _ _  
_ _ _ _ _  
\
Select the folder.  
MUSIC  
000/000 0:00:00 / 0:00:00  
Move the cursor to desired folder by  
pressing [œ √…†] button and press  
[ENTER] button to confirm.  
3
4
LIST PROGRAM  
max 6  
SKY  
winamp  
_ _ _ _  
_ _ _  
_ _ _ _ _  
_ _ _  
_ _ _ _ _  
\
Select the file to listen to (or view).  
MUSIC > MP3  
001/018 0:00:34 / 0:03:59  
Move the cursor to file which you want to  
listen to (or view) by pressing [œ √…†  
button  
LIST  
_ _  
PROGRAM  
]
mp3  
1. 01(musicfamily.i  
2. 02(musicfamily.i  
3. 03(musicfamily.i  
4. 04(musicfamily.i  
5. 05(musicfamily.i  
6. 06(musicfamily.i  
7. 07(musicfamily.i  
mp3  
mp3  
mp3  
mp3  
mp3  
mp3  
Press [PLAY] or [ENTER] to start playback.  
The selected file will play.  
\max 6\01(musicfamily.i.am) Smooth-  
Press [] to stop playback.  
* Only MP3 or CDDA file is listed.  
43  
About MP3, JPG and MPG discs  
Repeat playback mode.  
MUSIC > MP3  
001/018 0:00:34 / 0:03:59 Repeat one  
Every time you press [REPEAT], repeat  
5
6
playback mode changes as follows: Repeat  
one Repeat all Random OFF ...  
LIST  
_ _  
PROGRAM  
mp3  
mp3  
mp3  
mp3  
mp3  
mp3  
mp3  
1. 01(musicfamily.i  
2. 02(musicfamily.i  
3. 03(musicfamily.i  
4. 04(musicfamily.i  
5. 05(musicfamily.i  
6. 06(musicfamily.i  
7. 07(musicfamily.i  
Or select  
by pressing [√ †] and press  
[ENTER].  
The selected file or folder will playback  
repeatedly.  
\max 6\01(musicfamily.i.am) Smooth-  
You can programme playback.  
MUSIC > MP3  
001/018 0:00:34 / 0:03:59 REPEAT FILE  
Select the file to programme. Then press  
[PROGRAM].  
LIST  
PROGRAM  
mp3  
_ _  
mp3  
mp3  
mp3  
mp3  
mp3  
6. 06(musicfamily.i  
The selected file will go into PROGRAM  
folder.  
mp3  
mp3  
1. 01(musicfamily.i  
2. 02(musicfamily.i  
3. 03(musicfamily.i  
4. 04(musicfamily.i  
5. 05(musicfamily.i  
6. 06(musicfamily.i  
7. 07(musicfamily.i  
2. 02(musicfamily.i  
5. 05(musicfamily.i  
Press [PLAY] or [ENTER] in PROGRAM  
folder.  
mp3  
mp3  
If you want to delete all the files in the  
\max 6\02(musicfamily.i.am) Lager T  
PROGRAM folder, select  
] and press [ENTER].  
by pressing [√  
If you want to delete one file, press  
[CLEAR] button.  
The ability of this unit to read MP3 discs is dependent on the followings:  
The Bit Rate must be within 64-256 kbps.  
The maximum number of directories should not exceed 32.  
The maximum depth level of directories should not exceed 4.  
In the case that the file is recorded with a variable bit rate (VBR) in one file (Example: 54-256kbps) sound  
breakup sound breaking may occur during playback.  
File names should be named using 8 or fewer letters and/or numbers, and must incorporate the  
“MP3” file extension. EXAMPLE:  
. MP3 where each is a letter or number.  
********  
*
Use only letters and/ or numbers in file names. If you use special characters, the file and/ or folder  
names may not be displayed correctly on the on-screen display.  
Caution  
Try to avoid the use of the CD-RW(Rewritable) disc if possible because it can not be played back  
according to the recording format.  
A CD-R must be recorded with the standard format because it can not be played back according to  
any other recording format.  
A CD-R should be written using the ‘disc at once’ method.  
A disc which is made according to the ISO 9660 format can be played back.  
44  
About MP3, JPG and MPG discs  
Playing a disc containing JPG (PHOTO) files  
This unit will play JPG files recorded on CD-R and CD-RW discs.  
PICTURE > JPG  
000/000 0:00:00 / 0:00:00  
Select the desired folder.  
Move the cursor to the desired  
1
LIST  
PREVIEW  
folder by pressing […†] and  
press [ENTER] to confirm.  
DESKTOP  
PHOTO  
TEMPORAR  
TRASH  
\
PICTURE > JPG  
000/000 0:00:00 / 0:00:00  
Slideshow Delay Time set.  
Select “  
Slideshow &Delay  
LIST  
__  
2
3
PREVIEW  
Time” function. Then press  
jpg  
jpg  
jpg  
jpg  
jpg  
jpg  
jpg  
[ENTER] to adjust the slideshow  
delay time from 0FF to 10 seconds.  
1. BAK001  
2. BAK002  
3. BAK003  
4. BAK004  
5. BAK005  
6. BAK006  
7. BAK007  
* Only JPG file is listed.  
\PHOTO\320\BAK001.JPG  
Start the slideshow of file.  
✔  
If you press [PLAY] or [ENTER]  
when a JPG image is selected, a  
slideshow will begin automatically  
starting from the selected image.  
• To stop the slideshow, press  
[STOP].  
To turn left, press [  
To turn right, press [  
œ
].  
].  
12/134 œ 90°  
90°  
œœ √√  
/  
✔✔  
DISPLAY  
To skip to next screen (or file), press [].  
To skip to previous screen (or file), press [œœ ].  
Combination Play set.  
PICTURE > JPG  
000/000 0:00:00 / 0:00:00  
Select “ Combination Play”  
function.  
4
LIST  
__  
PREVIEW  
jpg  
jpg  
Then press [ENTER] or [PLAY]  
to enter into the playback of total  
files.  
1. BAK001  
2. BAK002  
3. BAK003  
4. BAK004  
5. BAK005  
6. BAK006  
7. BAK007  
jpg  
jpg  
jpg  
jpg  
jpg  
A combination play will begin.  
\PHOTO\320\BAK001.JPG  
45  
About MP3, JPG and MPG discs  
Playing a disc containing MPG (MOVIE) files  
This unit will play MPG files recorded on CD-R and CD-RW discs.  
MOVIE  
0/00 0:00:00 / 0:00:00  
Select the desired folder.  
Move the cursor to the desired  
1
LIST  
PREVIEW  
folder by pressing […†] and  
press [ENTER] to confirm.  
DESKTOP  
MOVIE  
TEMPORAR  
TRASH  
\
Select the desired MPG file.  
MOVIE  
0/00 0:00:00 / 0:00:00  
Move the cursor to the desired  
2
LIST  
__  
PREVIEW  
MPG file. Then press [ENTER] or  
[PLAY] button to playback.  
mpg  
1. BAK001  
mpg  
2. BAK002  
mpg  
3. BAK003  
mpg  
4. BAK004  
mpg  
5. BAK005  
* Only MPG file is listed.  
mpg  
6. BAK006  
mpg  
7. BAK007  
\MOVIE\320\BAK001.MPG  
Start the playback of MPG file.  
✔  
If you press [ENTER] or [PLAY]  
3
button, selected MPG file starts  
playback.  
If you press [DISPLAY] button, it  
shows the current disc mode.  
001/003  
00:01:03  
OFF  
current track / total track number  
time elapsed  
repeat playback mode  
0-9  
• To stop the playback, press [STOP].  
• To skip to next movie (or file), press [√√  
].  
• To skip to previous movie (or file), press [  
œœ].  
• To view fast forward playback, press [√√].  
• To view fast reverse playback, press [œœ].  
46  
Displaying menus on a disc  
To display menus on a disc  
If a disc includes menus, the user may display them.  
Press [MENU] button.  
In the case of a DVD disc, it shows the menus on the disc. Also they are  
different according to the discs.  
1
2
If it is a VCD2.0, select PBC ON mode by pressing [TITLE/PBC] button.  
* CD and VCD1.1 do not support the function.  
If it is a DVD disc, move the cursor to the relevant item with the arrow buttons  
œ √…†] and select one with [ENTER] button or [PLAY] button.  
[
47  
Language Setup  
A user can set OSD language, Audio, Subtitle and Disc Menu.  
While in STOP or RESUME STOP mode, press  
[SETUP] button.  
OSD  
AUDIO  
SUBTITLE  
DISC MENU  
ENGLISH  
AUTO  
OFF  
1
AUTO  
“OSD” means  
“On Screen Display”.  
Selecting an OSD language.  
OSD  
AUDIO  
SUBTITLE  
DISC MENU  
ENGLISH  
FRENCH  
SPANISH  
GERMAN  
ITALIAN  
Select an OSD language to be displayed on DVD  
menus with [ENTER].  
2
3
PORTUGUESE  
SWEDISH  
DUTCH  
Selecting Audio language.  
OSD  
AUDIO  
SUBTITLE  
DISC MENU  
FRENCH  
SPANISH  
GERMAN  
ITALIAN  
PORTUGUESE  
SWEDISH  
DUTCH  
Set your preferred audio language with  
[ENTER]. If the audio language is set and  
recorded on the DISC, it is automatically played  
back in the set language every time it is played.  
In case a disc  
does not include  
setting languages  
AUTO  
information, the  
selected language does  
not appear.  
OTHERS - - - - : Another language can be  
selected. You can input a 4-digit language code.  
Refer to the language codes on next page. Press [CLEAR] if an  
incorrect language code is entered.  
OSD  
AUDIO  
SUBTITLE  
DISC MENU  
SPANISH  
GERMAN  
ITALIAN  
PORTUGUESE  
SWEDISH  
DUTCH  
AUTO  
OTHERS - - - -  
Selecting Subtitle language.  
OSD  
FRENCH  
AUDIO  
SUBTITLE  
DISC MENU  
SPANISH  
GERMAN  
ITALIAN  
PORTUGUESE  
SWEDISH  
DUTCH  
Set your preferred subtitle with [ENTER]. If the  
subtitle language is set and recorded on the  
DISC, it is automatically played back in the set  
language every time it is played.  
4
OFF  
OTHERS - - - - : Another language can be  
selected. You can input a 4-digit language code.  
Refer to the language codes on next page. Press [CLEAR]  
if an incorrect language code is entered.  
OSD  
AUDIO  
SUBTITLE  
DISC MENU  
SPANISH  
GERMAN  
ITALIAN  
PORTUGUESE  
SWEDISH  
DUTCH  
OFF  
OTHERS - - - -  
48  
Language Setup  
Selecting Disc Menu language.  
OSD  
AUDIO  
SUBTITLE  
DISC MENU  
FRENCH  
SPANISH  
GERMAN  
ITALIAN  
PORTUGUESE  
SWEDISH  
DUTCH  
Set your preferred DISC MENU language with  
[ENTER]. If the DISC MENU language is set and  
recorded on the DISC, it is automatically played  
back in the set language every time it is played.  
5
AUTO  
OTHERS - - - - : Another language can be  
selected. You can input a 4-digit language code.  
Refer to the language codes. Press [CLEAR] if an  
incorrect language code is entered.  
OSD  
AUDIO  
SUBTITLE  
DISC MENU  
SPANISH  
GERMAN  
ITALIAN  
PORTUGUESE  
SWEDISH  
DUTCH  
AUTO  
OTHERS - - - -  
Table of language and Their Abbreviations  
Enter the appropriate code number for the initial settings “AUDIO”, “SUBTITLE”  
and/or “DISC MENU”.  
Code Language  
6565 Afar  
6566 Abkhazian  
6570 Afrikaans  
6577 Ameharic  
6582 Arabic  
6583 Assamese  
6588 Aymara  
6590 Azerbaijani  
6665 Bashkir  
6669 Byelorussian  
6671 Bulgarian  
6672 Bihari  
Code Language  
6983 Spanish  
6984 Estonian  
6985 Basque  
7065 Persian  
7073 Finnish  
7074 Fiji  
7079 Faroese  
7082 French  
7089 Frisian  
7165 Irish  
Code Language  
7473 Yiddish  
7487 Javanese  
7565 Georgian  
7575 Kazakh  
7576 Greenlandic  
7577 Cambodian  
7578 Kannada  
7579 Korean  
7583 Kashmiri  
7585 Kurdish  
Code Language  
7789 Burmese  
7865 Nauru  
7869 Nepali  
7876 Dutch  
7879 Norwegian  
7982 Oriya  
8065 Panjabi  
8076 Polish  
8083 Pashto, Pushto  
8084 Portuguese  
8185 Quechua  
Code Language  
8385 Sundanese  
8386 Swedish  
8387 Swahili  
8465 Tamil  
8469 Telugu  
8471 Tajik  
8472 Thai  
8473 Tigrinya  
8475 Turkmen  
8476 Tagalog  
8479 Tonga  
7168 Scots Gaelic 7589 Kirghiz  
7176 Galician  
7665 Latin  
8277 Rhaeto-Romance 8482 Turkish  
6678 Bengali;Bangla 7178 Guarani  
7678 Lingala  
7679 Laothian  
7684 Lithuanian  
7686 Latvian, Lettish 8368 Sindhi  
7771 Malagasy  
7773 Maori  
8279 Romanian  
8285 Russian  
8365 Sansrit  
8484 Tatar  
8487 Twi  
8575 Ukrainian  
8582 Urdu  
8590 Uzbek  
8673 Vietnamese  
8679 Volapük  
8779 Wolof  
8872 Xhosa  
8979 Yoruba  
9072 Chinese  
9085 Zulu  
6679 Tibetan  
6682 Breton  
6765 Catalan  
6779 Corsican  
6783 Czech  
6789 Welsh  
6865 Danish  
6869 German  
6890 Bhutani  
6976 Greek  
7185 Gujarati  
7265 Hausa  
7273 Hindi  
7282 Croatian  
7285 Hungarian  
7289 Armenian  
7365 Interlingua  
7378 Indonesian 7778 Mongolian  
7383 Icelandic  
7384 Italian  
8372 Serbo-Croatian  
8373 Singhalese  
8375 Slovak  
8376 Slovenian  
8377 Samoan  
8378 Shona  
8379 Somali  
8381 Albanian  
8382 Serbian  
7775 Macedonian  
7776 Malayalam  
7779 Moldavian  
7782 Marathi  
7783 Malay  
6978 English  
6979 Esperanto  
7387 Hebrew  
7465 Japanese  
7784 Maltese  
49  
Video Setup  
A user can set up a connected TV and screen size condition.  
While in STOP or RESUME STOP mode,  
TV ASPECT  
4:3 LB  
press [SETUP] button.  
1
Selecting TV Aspect.  
TV ASPECT  
4:3 LB  
Set your preferred TV ASPECT ratio with  
[ENTER] button.  
4:3 PS  
16:9 WIDE  
2
If a user selects “4:3 PS”, the user can watch  
only a centre of the original scene of “16:9”. If a  
user selects “4:3 LB”, the user can watch the  
original scene of “16:9”, but the top and bottom  
of the screen look black color.  
If a disc size is originally recorded in 4:3, the  
user cannot watch it in the wide screen format  
even though the user has set it to “16:9 Wide”.  
50  
Audio Setup  
A user may select an audio menu according to the speaker set being used.  
While in STOP or RESUME STOP mode,  
press [SETUP] button.  
DIGITAL OUT BITSTREAM  
DYNAMIC RANGE OFF  
1
Select a Digital Output.  
DIGITAL OUT BITSTREAM  
Set audio output to coaxial or optical. You  
can set the outgoing digital signal to  
DYNAMIC RANGE  
LPCM  
2
BITSTREAM or LPCM:  
BITSTREAM : The raw audio signal  
recorded on the disc goes to the digital  
audio output.  
LPCM : The decoded audio signal goes  
to the digital audio output.  
Select a Dynamic Range.  
DIGITAL OUT  
DYNAMIC RANGE  
You can set the Dynamic Range as follows:  
3
FULL  
OFF  
Off : You can hear the sound as it was  
originally recorded on the disc.  
Full : You can hear loud sounds softer  
and soft sounds louder.  
51  
Other Setup  
While in STOP or RESUME STOP mode, press  
OSD  
ON  
SCREEN SAVER ON  
[SETUP] button.  
DEFAULTS  
PARENTAL  
PASSWORD  
RESET  
8 ADULT  
1
2
3
Select character display window.  
OSD  
ON  
OFF  
SCREEN SAVER  
DEFAULTS  
PARENTAL  
PASSWORD  
Select "On" to make the OSD (On Screen Display)  
language appear on screen.  
Select screensaver.  
OSD  
SCREEN SAVER  
DEFAULTS  
PARENTAL  
PASSWORD  
ON  
OFF  
If bright scenes continue to be displayed on  
screen, the TV can be damaged. If the screen  
saver is set to “ON” and the resume stop, stop, or  
open status is maintained for about 5 minutes, the  
screensaver will function automatically causing  
the DVD logo to move continuously.  
Restoring DEFAULTS.  
OSD  
If you press [ENTER] when the cursor  
highlights RESET, an “Are you sure?”  
message will appear. Confirm with [OK].  
SCREEN SAVER  
DEFAULTS  
PAR
Are you sure?  
4
5
RESET  
PAS
This feature resets every function to its  
original Factory Defaults except the Parental  
Control settings.  
OK  
CANCEL  
Select Parental.  
OSD  
1 KIDS  
2 G  
3 PG  
4 PG-13  
5 PG-R  
6 R  
7 NC-17  
8 ADULT  
Press [] button when the cursor is  
highlighting PARENTAL.  
SCREEN SAVER  
DEFAULTS  
PARENTAL  
PASSWORD  
When “INPUT PASSWORD” appears on the  
screen, input the password.  
Change Parental Rating level.  
OSD  
1 KIDS  
2 G  
3 PG  
4 PG-13  
5 PG-R  
6 R  
7 NC-17  
8 ADULT  
Once you have entered the correct  
password, you can change the PARENTAL  
rating by pressing […†]. And confirm it  
with [ENTER].  
SCREEN SAVER  
DEFAULTS  
PARENTAL  
PASSWORD  
These 8 levels of parental control, protect  
children from watching violence, sexual  
scenes and other objectionable material.  
52  
Other Setup  
Changing a password.  
OSD  
SCREEN SAVER  
DEFAULTS  
PARENTAL  
PASSWORD  
To change your password, move the cursor  
to “PASSWORD” and press [].  
6
Enter your current password.  
INPUT PASSWORD  
- - - -  
CANCEL  
OK  
Then enter a new password and press  
[ENTER].  
OSD  
SCREEN SAVER  
DEFAULTS  
PARENTAL  
PASSWORD  
INPUT PASSWORD  
- - - -  
Confirm the new password.  
OSD  
SCREEN SAVER  
DEFAULTS  
PARENTAL  
PASSWORD  
CONFIRM PASSWORD  
- - - -  
OSD  
Now your password is changed.  
SCREEN SAVER  
DEFAULTS  
PARENTAL  
PASSWORD  
CHANGE OK  
The initial password is 3308. In case you forget the newly-entered password, you can use 3308 as a  
password.  
“Parental Lock” activates only if you set a password and the unit goes into Lock status. When the  
disc has no parental function even if the disc is for adults only, the Parental Lock doesn’t activate.  
53  
About DVD  
Playable Discs  
• DVD, Video CD(Version 1.1, 2.0), S-VCD and Audio CD  
Disc type  
DVD  
Playable  
Possible  
Possible  
Possible  
Possible  
Possible  
Possible  
Possible  
Possible  
Possible  
Impossible  
Impossible  
Possible  
Restriction  
Region number 2 or Region number All  
Version 1.0/1.1/2.0, SVCD  
PCM or dts  
Video CD  
CD  
CD-ROM  
CD-R  
MP3 File  
Video-CD/CD/CD-ROM (MP3 File)  
Video-CD/CD/CD-ROM (MP3 File)  
DVD Video  
CD-RW  
DVD-R  
DVD-RW  
DVD+RW  
DVD-ROM  
DVD-RAM  
Photo CD  
DVD Video  
DVD Video  
except KODAC CD  
REGION MANAGEMENT INFORMATION  
This unit is designed and manufactured to respond to the Region Management information that is  
recorded on a DVD disc. The region number of this player is “2”. If the region number described on the  
DVD discs does not correspond to the Region number of this player, the player will not play this disc.  
This player will play DVD discs made for “ALL” regions. Therefore, this player will play DVD discs  
marked with labels containing the region number “2” or “ALL”.  
ALL  
2
(Region 2)  
(Region ALL)  
54  
About DVD  
Terms related to DVD  
DVD  
A DVD (abbreviation of Digital Versatile Disc or Digital Video Disc) can include 135 minutes of video  
information. And for audio, it can hold up to 8 kinds of languages and 32 kinds of subtitle languages. By  
using MPEG-2 video compression and digital 3D surround sound, DVD realizes high-definition video  
and quality sound like a movie theatre.  
CDDA  
MP3  
A CDDA (abbreviation of Compact disc digital audio) is a music disc that is currently used.  
Audio compression format that enables audio files to be stored and transferred on a computer with a  
relatively small file size. It enables you to enjoy CD quality music. (Short for MPEG-1 Layer 3)  
PBC  
This is recorded on a Video CD 2.0, Video CD 3.0 and SVCD. The scenes or information to be viewed (or  
listened to) can be selected interactively with the TV monitor by looking at the menu shown on the TV  
monitor. It stands for PlayBack Control.  
CHAPTER A title in a DVD is divided into many tracks, or chapters. A chapter is an area on the DVD to  
which you can navigate using the remote control to locate special electronic markers. The DVD  
player can then locate any particular scene and skip directly to it.  
TITLE  
TRACK  
dts  
This is the information recorded on a DVD. A DVD can be divided into many titles.  
In a video CD and audio CD. A disc consists of many tracks. The user can search for these tracks.  
Digital Theatre System is a 5.1 -channel surround sound system, which is widely used in movie  
theatres around the world. It enables the bit rate to be increased to provide good sound quality.  
“DTS” and “DTS Digital Out” are trademarks of Digital Theatre Systems, Inc.  
Multi Angle Some DVD discs contain various scenes that have been simultaneously shot from a number of  
different angles.  
PCM  
Linear PCM is a signal-recording format used in a CD, while CD is recorded in 44.1kHz/16bit, a  
DVD is recorded in 48KHz/16bit up to 96KHz/24bit.  
Dolby DigitalDolby Digital enables the delivery of mono through 5.1-channel audio at data rates from 32 kbps  
to 640 kbps, thus offering flexibility and economical performance as well as uncompromised  
sound quality.  
Bitstream  
Lt/Rt  
Digital audio data that is decoded into an analogue signal for subsequent output to speakers.  
It indicates L/R of Dolby Digital 2CH Downmix output.  
Downmix  
DOWNMIX is reproducing the proper audio when audio format recorded on a disc differs from  
the output audio channel configuration. For example, with just one stereo speaker system you can  
hear full 5.1 channel audio.  
RGB  
This stands for red, green and blue. It means the video signal separated into its three primary  
colour components ready to drive the picture tube almost directly. Two signalling connections are  
needed to make the television accept the synchronisation and RGB signals. All this is in the  
SCART connector. Not all televisions have RGB inputs.  
SCART  
An acronym (Syndicat des Constructeurs d'Appareils Radiorécepteurs et Téléviseurs) for a  
connector used with many kinds of audio-visual equipment. It is also called Peritel and Euro-  
connector.  
55  
About DVD  
Handling Disc  
Keep the disc clean and in good condition. Handle with care.  
Do not put sticky paper or tape on it.  
Do not expose a disc to direct sunlight or other forms of heating.  
After using the disc, please replace it in its case.  
Cleaning Disc  
Before using the disc, please wipe it from its centre outwards, using a clean, soft cloth.  
Do not use any type of solvent such as thinner, benzol (benzene), commercial cleaning  
goods or antistatic spray.  
56  
Basic information about VCR and Videotape  
Terms related with VCR  
AFT  
Automatic fine tuning, a circuit that automatically adjusts TV reception for optimum  
reception/picture.  
CABLE  
Cable television.  
Index Search A feature of this VCR that automatically records an index mark each time recording begins. It  
helps you locate a particular segment of the tape quickly and easily.  
LP  
Long Play, an intermediate tape recording speed that combines most of the picture/audio quality  
obtainable at the standard recording speed with some of the tape economy of Extended Play (EP).  
OSD  
OTR  
On-screen display of information pertinent to the features of the VCR.  
One-touch recording, a feature that allows you to record the program you’re watching by  
pressing the REC key. Each press of the key increases the recording time by 30 minutes, up to 10  
hours.  
RF  
Radio frequency, the composite audio/video signal supplied to a TV receiver (or other video  
component) by an antenna or cable system.  
Safety tab  
SP  
The plastic tab at the back of a video tape cassette which, when removed, prevents accidental  
erasure of a recording.  
Standard play, the recording speed to use when the best picture quality is of prime importance  
(and when total recording time is not).  
Dew/ Condensation  
If a VCR is moved from a cool place to a warm and damp place or to a place facing direct cool wind from say  
an air-conditioner...the change in, temperature results in condensation occurring on the head drum of the  
VCR.  
If dew condensation occurs,  
1
2
First, turn it on for one or two hours before using it.  
Do not use it because it may cause problems to the VCR or videotape.  
How to use a head cleaner  
In the case of an old or contaminated videotape, playback picture may not be clear due to the contamination  
of the VCR heads. Please remove contaminants using a head-cleaner. (See below!)  
Insert a head-cleaner into VCR  
1
2
Press “PLAY” for 5 seconds, and then press “FF” for about 10 seconds.  
PLAY (5secs)  
FF (10secs)  
3
Eject the head-cleaner from VCR  
• Should the playback picture still be poor or not viewable repeat the headcleaning process 2 or 3 times.  
Otherwise contact your Authorised Service Agent  
57  
Trouble Shooting guide (VCR)  
Symptom  
Checks  
“Power On” does not work.  
Please check whether the power plug is inserted in to the mains  
socket .  
Please check whether a videotape is inserted in.  
Switch off and reinsert plug into mains socket.  
It does not work even in “Power On”.  
A videotape is not recognised.  
Please check whether the power plug is inserted in to the mains socket.  
Please check whether a videotape was inserted.  
Please check whether a videotape is inserted the correct way up!  
(The side of transparent window should be on the upside)  
Have you tried to re-insert a videotape just after the tape was  
ejected? Please try again after fully ejecting.  
On inserting a videotape, the tape is  
re-ejected.  
This is a safety mode to protect the videotape and is operated  
automatically. Please pull out the tape and put it in again.  
The videotape is not ejected.  
If the product has not been used for a long time, the cassette may not  
eject because the videotape has stretched. In this case, please pull out  
the power plug for about 10mins and then press “EJECT” button.  
Please check your antenna’s interconnections.  
TV channel should be tuned to the unit on a vacant programme  
number video channel.  
Please check your antenna’s signal it may be weak. If signal is weak  
contact aerial specialist.  
A picture on the video channel and a  
playback image do not appear.  
Not receiving an off-air signal but  
displays playback images.  
Press “TV/VCR” and then ensure “VCR” is displayed on the display panel.  
Is VCR turned on?  
Select TV by pressing [TV/VCR] button on remote control.  
No picture on VCR channel.  
Whilst playing a videotape, there may be some noise experienced in  
the beginning of the videotape or when resuming “PAUSE”. This  
NOT a fault  
Noise appears on screen after  
playback of recording.  
Please press “TRACKING” for improved picture. Videotape may be  
worn. Try to change it for another one.  
While in play, noise appears.  
Picture poor/noisy in play  
Please use a head-cleaner to clean VCR heads. VCR heads may be  
contaminated.  
Sound and playback image are poor.  
Sound presents but picture does not  
appear.  
Picture is irregular and stripes appear.  
"Error" message is displayed on screen.  
Since VCR Play signals are not as stable as TV signals, the playback  
image may appear unstable or distorted. To fix the problem, ensure  
you are tuned in to the ‘VCR’ programme channel no. alternatively  
connect via scart lead+select A/V or TV.  
When playing back a recording, the  
top of picture waves about.  
If the videotape signal was recorded by another/incompatible  
product or old faulty unit, horizontal noise bars may appear on the  
screen.  
Picture is not clear.  
Try to adjust the screen by [TRACKING+/-] button  
Try to use a head-cleaner.  
Try to use a head-cleaner.  
Try to adjust the screen by [TRACKING+/-] button.  
If 2 head machine then this symptom is not a fault!  
Picture on pause is unstable or slow  
motion is not clear.  
58  
Trouble Shooting guide (VCR)  
Symptom  
Checks  
Recording a TV program is  
impossible.  
For recording, you should use videotape with a tab. Ensure tab is  
NOT removed  
Ensure there is no RF clash if so change RF output.  
Please check whether the timer recording info is right.  
Are RF cables input/antenna inputs connected correctly?  
After pressing “REC”, the videotape  
is ejected automatically.  
Please check whether the clock is right.  
Does the display on your video show “  
recording)? Please check!  
(Ready for timer  
Please check whether the timer recording info is right.  
Please check that the record protect tab on the cassette is intact. (If the  
tab is missing, cover the hole with a piece of scotch tape.)  
Timer recording of Cable TV does  
not work.  
Was a cable data output code connected correctly?  
Did you turn off your player? (Please turn it on.)  
In spite of pressing “CHANNEL”, a  
channel can not be set.  
You may have not memorised channels.  
Please check your channel setting or press a number button.  
When duplicating/ copying, picture  
is poor anddistorted.  
Some tapes or discs distributed in the rental market for hire are  
copyright protected to prevent copying. These tapes cannot be  
duplicated.  
remote control does not work.  
Battery may be weak or exhausted.  
The receiver of remote control may be of an incompatible frequency to  
sender frequency.  
Buttons on remote control do not  
work.  
During index search when videotape is positioned towards the  
beginning, “VISS REW” and “REW” do not work.  
If videotape is at the end, “FF”, “VISS FF”, “PLAY” and “REC” will  
not work.  
VISS index search does not work.  
Are you playing a tape that was not recorded on this machine? (Try  
to re-record it using this recorder.)  
You may start recording it in “REC-PAUSE”. Otherwise start  
recording from stop condition.  
Cable broadcasting can not be  
selected.  
Please select “CABLE” programme number from the “CHANNEL  
SETTING”.  
59  
Trouble Shooting guide (DVD)  
Symptom  
Checks  
The recorder does not play.  
If a DVD is from overseas, it may not be played. Please check a  
DVD’s region code whether it has the relative region code 2 or All.  
Please check whether a DVD is inserted in an upright direction (Label up)  
If it is a CD-ROM for PC or DVD-ROM, it will not work.  
.
No sound comes through.  
During play mode if “SLOW” or “PAUSE” selected. (There will be  
no sound output.)  
Are all connections correct?  
Please check the operative condition of TV or amplifier.  
From SETUP, please check “AUDIO” menu.  
A disc is playing but a picture does  
not appear or a poor picture appears.  
Did you turn on your TV set?  
Are all connections correct?  
Play may be in “PAUSE” mode.  
A disc may have some contaminants or be damaged.  
A disc may be faulty.  
Sound is irregular  
Please check the connection with Dolby Digital amplifier.  
Please check the plugs are connected properly.  
Check all contacts and connections.  
REMOTE does not work.  
Please check the angle of operation of the remote control, the distance  
and any obstacles that may be interrupting the signal.  
Battery may be weak or exhausted.  
When you operate DVD, use it by pressing [DVD] button.  
Dolby Digital sound does not work  
Dolby Digital sound can be reproduced via a Dolby Digital amplifier only.  
Please check “Dolby Digital ” mark on your DVD.  
If playing it through the digital output, while pressing “STOP”,  
please check whether “Digital Output” is “Bitstream” by pressing  
“SETUP” on menu.  
Please check that the connection is correct.  
“AUDIO” or “SUBTITLE” button  
does not work.  
If a DVD does not include language information, these functions are  
not supported.  
“ANGLE” button does not work  
while a DVD is playing.  
“ANGLE” is supported only by a DVD that contains multi angle scenes.  
The “ANGLE” mark on screen will confirm that to the user this feature  
is supported.  
Please check the angle of operation of the remote control, the distance  
and any obstacles that may be interrupting the signal.  
Please check that the battery in the remote control is not exhausted.  
DVD may not contain menu information.  
“MENU” does not appear while a  
DVD is playing.  
The file name of MP3 only recognises the Alphabet (A~Z, a~z),  
numbers (0~9) and a special symbols on keyboard (~, !, @, #, $ ....)  
10 letters can be displayed at maximum.  
The file name of MP3 (CD-R) appears  
with strange letters.  
The letters above will be displayed as follows “----”.  
If the surface of the disc is marked, the file display and playback will  
not be possible.  
Any MP3 (CD-R) file isn’t displayed.  
60  
Specifications  
Supply Voltage  
200-240V~, 50/60Hz  
Power Consumption  
Weight  
HiFi :22W, Mono:20W  
4.6kg  
Dimension (W x H x D)  
Operating temperature  
Installation condition  
Laser output  
435mmx93mmx255mm (without foot), 435mmx98mmx255mm (with foot)  
+5°C~40°C  
Horizontal / Relative humidity under 80%  
5mW (continuous wave max.)  
635nm (DVD), 730nm (CD)  
Wave length  
Signal type  
PAL COLOR  
Antenna Input/output  
VIDEO input  
U/V-mixed: 75unbalanced  
1.0Vp-p (unbalanced, RCA JACK)  
-8.8dBm, RCA JACK  
AUDIO input  
VIDEO output (common use of DVD and VCR)  
VIDEO output (DVD only)  
AUDIO output (common use of DVD and VCR)  
AUDIO output (DVD only)  
VIDEO output terminal, 1.0 Vp-p unbalanced, RCA JACK, SCART JACK  
RGB output (75In load R: 0.7Vp-p, G:0.7Vp-p, B:0.7Vp-p)  
Audio output terminal (2 kinds): -5.8dBm (VCR), 2Vrms(DVD), RCA JACK  
Analogue AUDIO output : 2.0Vrms  
Digital audio output (OPTICAL, COAXIAL)  
Very high density tapes with VHS marks  
DVD, VIDEO-CD, CD (12cm), CD (8cm), MP3, CD-R, CD-RW  
SP: 23.39mm/s, LP: 11.70mm/s  
SP: 3hrs, LP: 6hrs (use of E180tape)  
24 hrs  
Playable tape  
Playable disc  
Tape speed  
Playing time  
Clock display  
Time Recording  
Power failure back-up period  
VIDEO S/N (VCR)  
8 programs a month  
1min  
Over 43dB(Standard recording)  
Over 240 lines (Standard recording)  
Over 400 lines (Playback DVD)  
Over 65dB  
Resolution  
VCR  
DVD  
AUDIO (VCR)  
AUDIO (DVD)  
90dB  
90dB  
AUDIO dynamic range  
DVD Audio output standards  
Disc type  
Output  
DVD  
VIDEO-CD  
CD  
Analogue Audio output  
Digital Audio output  
48/96KHz sampling 44.1KHz sampling 44.1KHz sampling  
48KHz sampling  
48KHz sampling  
44.1KHz sampling 44.1KHz sampling  
44.1KHz sampling 44.1KHz sampling  
Optical digital audio output  
61  
QUICK START GUIDE FOR SORTING CHANNELS ON THE DVD COMBO  
Once the ‘Auto Set’ function has been completed the On Screen Display will show a list of the  
channels which it has found, displayed in the order it found them.  
It is unlikely, that they will be in the correct oder ie. BBC1 as PR01, BBC2 as PR02, ITV as PR03,  
Channel4 as PR04 and Channel 5 as PR05.  
Therefore, it will be necessary to Sort the channels displayed, into the correct order.  
Please follow the following procedure.  
STOP  
SP  
PR01 P-01  
1
2
3
Press the [VCR] button to select the VCR mode.  
Press the [SETUP] button.  
SETUP  
TIMER PROGRAM  
PR PRESET  
Select the ‘PR PRESET’ using  
button.  
[
/
] buttons and press the [OK/ENTER]  
VCR SETUP  
TAPE CONTROL  
PR+/-:SELECT  
OK:CONFIRM  
SETUP:END  
4
5
6
Select the ‘PR ALIGN’ using  
button.  
[
/
] buttons and press the [OK/ENTER]  
PR PRESET  
AUTO SET  
MANUAL SET  
PR ERASE  
PR ALIGN  
Select the channel that needs to be moved and press the [OK/ENTER]  
button.  
PR+/-:SELECT  
OK:CONFIRM  
SETUP:END  
PR ALIGN  
PR01 P-01 PR08 P-08  
PR02 BBC2 PR09 P-09  
PR03 P-03 PR10 P-10  
PR04 P-04 PR11 P-11  
PR05 MTV PR12 ----  
PR06 BBC1 PR13 ----  
PR07 P-07 PR14 ----  
Press the [OK/ENTER] button in order to select the ‘PR’ number which  
you want to place the current selected channel using  
[
/
] buttons.  
ie. PR01 BBC1. And press the [OK/ENTER] button to confirm.  
PR+/-:ALIGN  
:PR VIEW  
OK:CONFIRM  
SETUP:END  
PR ALIGN  
PR01 BBC1 PR08 P-08  
PR02 P-01 PR09 P-09  
PR03 BBC2 PR10 P-10  
PR04 P-03 PR11 P-11  
PR05 P-04 PR12 ----  
PR06 MTV PR13 ----  
PR07 P-07 PR14 ----  
Repeat above 5-6 steps to align the other channels.  
PR+/-:ALIGN  
:PR VIEW  
OK:CONFIRM  
SETUP:END  
62  

Garland GIWOK 3 5 KW User Manual
Frymaster GSMS User Manual
Fisher PC 19R10 User Manual
Electrolux GLASKERAMIK KOCHFELD 6000K User Manual
Durabrand DBTV2500 User Manual
Dacor Cooktop DR30GFS User Manual
Cypress CY7C1520KV18 User Manual
AT T 1465 User Manual
Asus Z87M Plus Manual Z87M PLUS User Manual
AEG Cooktop HK854080XB User Manual