D704HS™
D702HS™
User Guide
Expandable Handset for Clarity®
Cordless Phones
D702HS is compatible with:
•
•
•
D702
D712
D722
D704HS is compatible with:
•
•
•
D704
D714
D724
Clarity, a Division of Plantronics, Inc.
4289 Bonny Oaks Drive,
Chattanooga,TN 37406
Tel: 800-426-3738 Fax: 800-325-8871
E-mail: [email protected]
©2011 Clarity, a Division of Plantronics, Inc.All rights reserved.
Clarity, D702HS, D704HS are trademarks or registered trademarks
of Plantronics, Inc.
Rev.A (04-08)
PRINTED IN CHINA
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
13. To reduce the risk of electrical shock, do not take this phone apart. Opening
or removing covers may expose you to dangerous voltages or other
risks. Incorrect reassembly can cause electric shock when the appliance is
subsequently used.
you experience hearing discomfort, you should have your hearing checked
by a doctor.To protect your hearing, you should:
•
Set the volume control in a low position and gradually increase
the volume as needed. Before pressing the BOOST button, reduce
the volume to the lowest level. Use the phone on the lowest volume
setting as possible.
14. Unplug this product from the wall outlet and refer servicing to the
manufacturer under the following conditions: when the power supply
cord or plug is frayed or damaged; if liquid has been spilled into the
product; if the telephone has been exposed to rain or water; if the
telephone has been dropped or the case has been damaged; if the
telephone exhibits a distinct change in performance; if the telephone does
not operate normally by following the operating instructions.Adjust only
those controls that are covered by the operating instructions. Improper
adjustment may require extensive work by a qualified technician to restore
the telephone to normal operation; if the telephone does not operate
normally by following the operating instructions.
•
Limit the amount of time you use the telephone at high volume
evels.
21. If you experience a skin irritation after using this product, discontinue use
and contact Clarity.
BATTERY SAFETY INSTRUCTIONS
15. This product should be operated only from the type of power source
indicated on the marking label. If you are not sure of the type of power
supply to your home, consult your local power company.
16. Do not attempt to open the AC adapter.There are potentially dangerous
voltages inside, and there are no serviceable parts.
17. Discontinue use of product and contact Clarity if the product overheats,
has a damaged cord or plug, if the product has been dropped or damaged
or if the product has come into contact with liquids.
18. Use only the AC adapter provided with this product or a replacement AC
adapter provided by Clarity.
19. This phone amplifies sound to loud volumes.To prevent hearing damage, all
users of the phone should be informed of the high volume capability of
the phone and children should only use the phone when supervised by an
adult.
20. Exposure to high volume sound levels or excessive sound pressure may
cause temporary or permanent damage to your hearing.Although there
is no single volume setting that is appropriate for everyone, you should
always use your telephone with the volume set at moderate levels and
avoid prolonged exposure to high volume sound levels.The louder the
volume, the less time is required before your hearing could be affected. If
Dispose of used batteries according to the instructions.
1. Do not dispose of the battery in a fire as it may explode. Check with local
codes for possible special disposal instructions.
2. Do not open or mutilate the battery. Released electrolyte is corrosive and
may cause damage to the eyes and skin. It may be toxic if swallowed.
3. Exercise care in handling batteries in order not to short the battery
with conducting materials such as rings, bracelets and keys.The battery or
conduction material may overheat and cause burns.
4. Remove batteries when they are discharged and when the equipment will not
be used for an extended period of time. Dispose of batteries according to local
environmental laws.
5. Do not disassemble, heat, crush, deform or puncture batteries.
6. Do not attempt to charge non-rechargeable batteries.
7. Keep batteries out of the reach of children.
2
3
PACKAGING CONTENTS/LOCATION
INSTALLING YOUR HANDSET
Connecting the charger base station
1) Locate the charger base; note that the power adapter is
permanently connected to your charger base.
2) Plug the end of power supply into the wall socket, as shown.
The package contains the following items:
• 1 Handset
• 1 Charger base with attached power adapter
• 1 Belt clip
• 2 Rechargeable batteries
• 1 User guide
Your package includes all the items as shown here. If there is anything missing,
please contact our Customer Care Department immediately.
NOTE: PLEASE RETAIN A COPY OF PROOF OF PURCHASE FORYOUR
RECORDS.
Location
For maximum coverage and reduce the interference, here are some guidelines
you should consider when you place the base unit:
- place it at a convenient, high,and central location with no obstructions
between the handset and base unit in an indoor environment.
- place it away from electronic appliances such as televisions, microwave ovens,
radios, personal computers, wireless devices or other cordless phones.
- avoid facing radio frequency transmitters, such as external antennas of mobile
phone cell stations.
- avoid plugging it into the same circuit as other major household electrical
appliances because of the potential for interference.Try moving the appliance
or the base unit to another power outlet.
If the reception for a base unit location is not satisfactory, move it to another
location for better reception.
Depending on the surrounding conditions as well as spatial and structural
factors, the range may be reduced.The range indoors is normally less than
outdoors.
LineCord
4
5
HOW TO REGISTER YOUR HANDSET
INSTALLING/CHARGING BATTERIES
1) Slide out the battery compartment cover.
2) Place the two batteries as indicated. Follow the polarity.
3) Slide the battery compartment cover back.
4) Put the handset on the base and charge for 16 hours first
time. A beep indicates that the handset is properly placed on
the base or charger.
Your telephone (sold separately) can support up to five cordless
handsets.The additional handset(s) needs to register with the
telephone base before use.You must register each additional handset
separately.
The handsets provided within your main unit (sold separately) are
already registered as HANDSET 1 and so forth.Additional handsets
are assigned numbers in the order they are registered (HANDSET 2
to HANDSET 5).
Use only NiMH rechargeable batteries.
NOTE: Please refer to the Battery Safety Instructions on page 6 for
proper use and disposal of the batteries.
When first purchased, all expansion handsets alternately display
•
Press FIND on base 4 sec
and
•
Then press # on handset.
The new handset should be charged without interruption for at least
30 minutes before registering to the telephone base.
How to add (register) your handset to the main unit
(sold separately)
NOTE: You must be in close proximity of your main unit's base in
order to register the handset; please move to where you can access
the FIND button on your main base (sold separately).
1. In idle mode, press <MENU/SELECT>, then <UP/DOWN> to
select Registration.
2. Press <MENU/SELECT> and screen will alternately show
•
Press FIND on base 4 sec
and
6
7
HOW TO DEREGISTER YOUR HANDSET(S)
HOW TO REGISTER YOUR HANDSET
•
Then press # on handset
Deregister all handsets
3. Press and hold FIND on the telephone base for about four
seconds.
You can deregister handsets.You may need to deregister your handsets
if:
4. Press # (pound key) on the handset.The screen shows
Registering...Please wait.
You have five registered handsets and need to replace a handset.
-OR-
You wish to change the designated handset number of your
registered handsets.
When the handset is registered successfully, HANDSET
registered and then HANDSET X appears on the screen, with X
being the handset number (1-5).
You must first deregister ALL the handsets, and then register each
handset you wish to use again, one at a time.
If the registration is not successful, the handset screen shows
Registration failed. Please start again from step 1 above.
Note: You cannot register a handset if any other system handset is in
use.To register an expansion handset, follow from the step 3 as above.
If the base of your main unit is represented by either of the drawings
below, follow the directions below the drawings:
1. Press and hold FIND on the telephone base for about 24
seconds; release FIND.
2. Immediately press FIND again.
3. When complete, the handset screen alternately shows
• Press FIND on base 4 sec
and
8
9
HOW TO DEREGISTER YOUR HANDSET(S)
HOW TO DEREGISTER YOUR HANDSET(S)
• Then press # on handset.
4. To register the handset(s) to the telephone base again, follow
the registration instructions in section Register a handset.
Note:
•
If the deregistration process is not successful, you might need to
reset the system and try again.To reset, unplug the power from
the telephone base and plug it back in.
NOTE: There are no visual or audible alerts to indicate
the base is under deregistration mode.
•
You cannot deregister the handset(s) if any system handset is in
use.
If the base of your main unit is represented by the drawing below,
follow the directions below the drawing:
Note:
If your handset is registered to a base, you can re-register it to
•
a different base without deregistering it from the original base.
Just follow the directions in the section How to add (register) your
handset to the main unit (sold separately).
1. Press and hold FIND on the telephone base for about 10
seconds, until the SPEAKER light starts flashing; release FIND.
2. Immediately press FIND again; you will hear two quick beep
tones.
3. When complete, the handset screen alternately shows
• Press FIND on base 4 sec
and
• Then press # on handset.
4. To register the handset(s) to the telephone base again, follow
the registration instructions in section Register a handset.
10
11
FOR ADDITIONAL INFORMATION...
TECHNICAL INFORMATION
...Please refer to the user guide included with the main unit (sold
separately). Once registered, your additional handset will perform the
same functions as your existing main handset.
• D702HS™ - 30dB
• D704HS™ - 40dB
To identify the model number of your additional handset:
•
Turn the charger base of your unit upside down; locate the
colored round label on your base.
Dimensions
• Handset Size: 7” x2 1/4” x 1 1/2” (H xW x D)
• Base Size: 2” x 3 3/4” x 3 1/2” (H xW x D)
• Orange label: D704HS™, up to 40dB of gain
• Compatible with:
• D704;
• D714;
• D724.
Weight
• HandsetWeight: 6.125 oz. (with batteries)
• BaseWeight: 2.75 oz.
• Green label: D702HS™, up to 30dB of gain.
• Compatible with:
• D702;
• D712;
• D722.
Power Requirements:
• AC Adapter (attached to base):
Input: 100V - 240V, 200mA
Thank you...
Output: 6VDC, 300 mA
• Battery: 2 X AAA, 600mAh Ni-MH
Use only NiMH rechargeable batteries.
NOTE: DO NOT MIX BATTERIES; REPLACE BOTH
BATTERIESWHEN NEEDED.
new system.
If you have any questions regarding the operation of this telephone, please contact
one of our Customer Service Representatives for prompt and useful information.
Phone: 800-426-3738
Fax: 800-325-8871
Email: [email protected]
12
13
|