SilkWorm 4016
Hardware Reference Manual
Supporting Fabric OS v5.0.4
Publication Number: 53-1000175-01
Publication Date: 1/30/2006
Document History
The following table lists all versions of the SilkWorm 4016 Hardware Reference Manual.
Document Title
Publication
Number
Summary of
Changes
Publication
Date
SilkWorm 4016 Hardware Reference Manual
53-1000175-01
New document.
January 2006
Contents
Optional Brocade Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii
Other Industry Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii
SilkWorm 4016 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Switch Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Additional Port Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Port Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Nonport Side. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Labeling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
SFPs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
ISL Trunking Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
Brocade Optional Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
iii
Unpacking the SilkWorm 4016. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Items Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Configuring the SilkWorm 4016. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Creating a Serial Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Connecting to the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Activating Ports on Demand (POD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
Interoperability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Port Negotiation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Operating System Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Accessing the SilkWorm 4016 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Interpreting POST Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Interpreting LED Activity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Weight and Physical Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Facility Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Architectural Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
Supported HBAs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
iv
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
Regulatory Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3
FCC Warning (US only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3
VCCI Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4
BSMI Statement (Chinese) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4
CE Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-5
Canadian Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-5
Laser Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-5
RTC Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-5
Electrical Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-6
Regulatory Certifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-6
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
v
vi
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
About This Document
This document is a hardware reference manual, written for SAN administrators who are using any blade
server that supports the Brocade SilkWorm 4016. It provides the information needed to understand the
installation, configuration, and maintenance of the Brocade SilkWorm 4016 switch module. This
document is specific to Brocade Fabric OS version 5.0.4 and the specified switch.
“About This Document” contains the following sections:
•
•
•
•
•
•
•
How This Document Is Organized
This document is organized to help you find the particular information that you want as quickly and
easily as possible. It provides specific information about the SilkWorm 4016.
As a hardware reference, this document begins with a brief overview of the SilkWorm 4016 before
proceeding to details of the switch.
The document contains the following components:
•
•
•
•
•
Chapter 1, “Introducing the SilkWorm 4016,” provides the basic concepts and a description of the
switch.
Chapter 2, “Installing the Brocade SilkWorm 4016,” explains the process used to insert the switch
into a PowerEdge 1855.
Chapter 3, “Configuring the Brocade SilkWorm 4016” describes how to connect to the switch and
change the IP address.
Chapter 4, “Operating the Brocade SilkWorm 4016,” provides more detail about configuring and
replacing a SilkWorm 4016.
Appendix A, “Brocade SilkWorm 4016 Specifications,” is a product specification reference.
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
v
Supported Hardware and Software
This document has been created to include information specific to the SilkWorm 4016 switch module
running Brocade Fabric OS version 5.0.4. This switch was designed specifically to work with a blade
server chassis.
This document does not support all 5.x Fabric OS versions: it is specific to the Fabric OS v5.0.4. To
obtain information about a different Fabric OS version, refer to the documentation specific to your
Fabric OS.
What’s New in This Document
This is a new document. For further information, see the Brocade Fabric OS v5.0.4 release notes.
Document Conventions
This section describes text formatting conventions and important notices formats.
Text Formatting
The narrative-text formatting conventions that are used in this document are as follows:
bold text
italic text
codetext
Identifies command names
Identifies GUI elements
Identifies keywords and operands
Identifies text to enter at the GUI or CLI
Provides emphasis
Identifies variables
Identifies paths and Internet addresses
Identifies document titles
Identifies CLI output
Identifies syntax examples
For readability, command names in the narrative portions of this guide are presented in mixed letter
case: for example, switchShow. In actual examples, command letter case is often all lowercase.
Otherwise, this manual specifically notes those cases in which a command is case sensitive.
Notes, Cautions, and Warnings
The following notices appear in this document.
Note
A note provides a tip, emphasizes important information, or provides a reference to related information.
vi
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
Caution
A caution alerts you to potential damage to hardware, firmware, software, or data.
Warning
A warning alerts you to potential danger to personnel.
For definitions of SAN-specific terms, visit the Storage Networking Industry Association online
Additional Information
This section lists additional Brocade and industry-specific documentation that you might find helpful.
Brocade Resources
The following related documentation is provided on the Brocade Documentation CD-ROM and on the
Brocade Web site, through Brocade Connect.
Note
password.
Fabric OS
•
•
•
•
Fabric OS Administrator’s Guide
Fabric OS Command Reference Manual
Fabric OS MIB Reference Manual
Fabric OS System Error Message Reference Manual
Fabric OS Optional Features
•
•
•
Web Tools Administrator’s Guide
Fabric Watch Administrator’s Guide
Secure Fabric OS Administrator’s Guide
SilkWorm 4016
•
•
•
SilkWorm 4016 Hardware Reference Manual (this document)
SilkWorm 4016 QuickStart Guide
Brocade Fabric OS v5.0.4 release notes
For practical discussions about SAN design, implementation, and maintenance, you can obtain Building
SANs with Brocade Fabric Switches through:
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
vii
For additional Brocade documentation, visit the Brocade SAN Info Center and click the Resource
Library location:
Release notes are available on the Brocade Connect Web site and are also bundled with the Fabric OS
firmware.
Optional Brocade Features
Optional Brocade features include:
Advanced Performance Monitoring
Enables more effective end-to-end SAN performance analysis to enhance
performance tuning, increase productivity, optimize resource utilization, and
reduce costs.
Extended Fabrics
Fabric Watch
Supports the reliable, high-speed connectivity of SilkWorm switches over dark
fiber or Dense Wave Division Multiplexing (DWDM) equipment at distances up
to 500 kilometers to enhance business continuance operations.
Continuously monitors SAN fabrics for potential faults based on thresholds set
for a variety of SAN fabric elements and events—automatically alerting
administrators to potential problems before they become costly failures.
ISL Trunking
Optimizes the performance and availability of SAN fabrics while simplifying
ISL management. Two 4 Gbit/sec SilkWorm switches can automatically group up
to eight ISLs into a single logical “trunk” with a total throughput of up to
32 Gbit/sec.
Advanced Zoning
Secure Fabric OS
Automatically groups SAN fabric-connected devices into logical zones that
restrict access to “member” devices in the zone. Advanced Zoning uses hardware
enforcement at both the port and WWN level to provide more robust data
protection.
Provides a comprehensive security solution to help protect mission-critical data.
Key features include centralized policy-based security management,
management data encryption, and authentication to create a fabric-wide trusted
environment with control over all levels of fabric access and communication.
Other Industry Resources
For additional resource information, visit the Technical Committee T11 Web site. This Web site
provides interface standards for high-performance and mass storage applications for Fibre Channel,
storage management, as well as other applications:
For information about the Fibre Channel industry, visit the Fibre Channel Industry Association Web
site:
viii
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
Getting Technical Help
Contact your switch support supplier for hardware, firmware, and software support, including product
repairs and part ordering. To expedite your call, have the following information available:
1. General Information
•
•
•
•
•
•
•
•
•
Technical Support contract number, if applicable
Switch model
Switch operating system version
Error numbers and messages received
supportSave command output
Detailed description of the problem and specific questions
Description of any troubleshooting steps already performed and results
Serial console and telnet session logs
syslog message logs
2. Switch Serial Number
The switch serial number and corresponding bar code are provided on the serial number label, as
shown here:
:
*FT00X0054E9
FT00X0054E9
The serial number label is located as follows:
•
•
•
•
•
SilkWorm 3014 switches: Top of chassis, under the insertion arm.
SilkWorm 3016, 4012, and 4016 switches: Side of switch module.
SilkWorm 200E, 3200, and 3800 switches: nonport side of chassis.
SilkWorm 3250, 3850, 3900, 4100, 4900, and 7500 switches: Bottom of chassis.
SilkWorm 24000, and 48000 directors: Inside the front of the chassis, on the wall to the left of
the ports.
•
SilkWorm Multiprotocol Router Model AP7420: On the bottom of the chassis and on the back
of the chassis.
3. World Wide Name (WWN)
•
SilkWorm 200E, 3014, 3016, 3250, 3800, 3850, 3900, 4012, 4016, 4100, 4900, 7500 switches
and SilkWorm 24000, and 48000 directors: Provide the license ID. Use the licenseIdShow
command to display the license ID.
•
•
SilkWorm Multiprotocol Router Model AP7420: Provide the switch WWN. Use the
switchShow command to display the switch WWN.
All other SilkWorm switches: Provide the switch WWN. Use the wwn command to display the
switch WWN.
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
ix
Document Feedback
Because quality is our first concern at Brocade, we have made every effort to ensure the accuracy and
completeness of this document. However, if you find an error or an omission, or you think that a topic
needs further development, we want to hear from you. Forward your feedback to:
Provide the title and version number and as much detail as possible about your comment, including the
topic heading and page number and your suggestions for improvement.
x
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
Chapter
Introducing the SilkWorm 4016
1
The SilkWorm 4016 is a 12-port Fibre Channel switch module (upgradable to 16 ports) that supports
link speeds up to 4Gbit/sec. It includes the Brocade Fabric Operating System (Fabric OS) and is
compatible with the entire SilkWorm product family.
This chapter provides the following information:
•
•
•
•
SilkWorm 4016 Features
The SilkWorm 4016 provides the following features:
•
Up to six external autosensing (1, 2, and 4 Gbit/sec) Fibre Channel ports:
-
Universal and self-configuring ports capable of becoming:
F_Port (fabric enabled)
FL_Port (fabric loop enabled)
E_Port (expansion port)
-
Brocade ISL Trunking of external ports with trunking license
•
•
•
Up to ten copper backplane F_ports capable of automatic negotiation to the highest common speed
of all devices connected to port, up to 4 Gbit/sec
Frame filtering that augments the hardware zoning capabilities of the Brocade ASIC, which
implements hardware zoning at the port level of the switch
Brocade ASIC expanded capabilities, including World Wide Name (WWN) and device-level
zoning
•
•
•
•
•
Hardware zoning, implemented by means of a firmware-accessible table per output port
Extensive diagnostics and monitoring capabilities
Unicast and broadcast data traffic support
Up to six SWL small form-factor pluggable (SFP) optical transceivers
One console port through the backplane connectors to the ; refer to the documentation for
connection details
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
1-1
1
SilkWorm 4016 Features
•
•
One 10/100 Mbit/sec autosensing Ethernet port with an RJ-45 connector with manual override for
speed, and full/half duplex operation
The following light-emitting diodes (LEDs) for each external port:
-
-
One green/amber LED to indicate status for each port
One green/amber LED to indicate link speed for each port
•
The following system light-emitting diodes (LEDs):
-
-
-
One green power LED to indicate module power-on
One green/amber LED to indicate module status
One green LED to indicate status
Each SilkWorm 4016 switch contains:
•
•
•
One PowerPC 405GP processor with a clock speed of 200 MHz
One real-time clock with 10-year battery
Five digital thermometers
1-2
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
1
Switch Characteristics
Switch Characteristics
This chapter describe the physical characteristics of the SilkWorm 4016.
Weight and Physical Dimensions
Table 1-1 lists the weight and physical dimensions of the SilkWorm 4016.
Table 1-1
Switch Specifications
SilkWorm 4016
1.27 in (32.2 mm)
Height
Width
Depth
Weight
5.13 in (130 mm)
10 in (254 mm)
2.32 lb — without media
Memory
Table 1-2
Memory Specifications
Memory Type
PowerPC 440GP processor
SDRAM
Value
200 MHz
256 Mbytes - for system memory at 64 bits
wide with 8 ECC bits
Boot flash
4 MB
Compact flash
SEEPROM
256 MB
256 Kbit
Additional Port Activation
Table 1-3 shows the base (included) ports as well as the additional 4 ports that can be activated by
installing an optional 4-port Ports-on-Demand (POD) license. For details about activating POD
licensing, see “Activating Ports on Demand (POD)” on page 3-6
Table 1-3
Ports available
Port Licensing External Ports
Internal Ports
0 through 7
8, 9
Base
POD
10 through 13
14, 15
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
1-3
1
Switch Characteristics
Port Side
Externally accessible ports and LEDs are on the port side of the switch. The port side faces out when the
switch is inserted into a . Figure 1-1 details the switch’s port side. For a complete description of the
The insertion arm is located just above the port side of the SilkWorm 4016 and ends with a plastic
handle, accessible at the front of the port side of the switch. This arm is used to remove and insert the
3
4
2
10
11
12
13
14
15
!
1
5
Figure 1-1 Port Side of the SilkWorm 4016
1
2
3
4
5
Ethernet port
Power and status LEDs
Top of SilkWorm 4016
Insertion arm latch
Autosensing ports
The nonport (switch status) LEDs, shown as item 2 of Figure 1-1, display switch-level information as
1
10
2
!
3
Figure 1-2 Nonport LEDs
1
2
3
Module controller status
Switch status
Power and module status
1-4
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
1
Switch Characteristics
Nonport Side
The nonport side of the SilkWorm 4016 (shown in Figure 1-3) is seated into the . You do not need to do
anything special to line up the SilkWorm 4016: it will seat correctly when the insertion arm is closed.
When the switch is inserted the backplane connectors activate a connection port, allowing the access
and control of the SilkWorm 4016 via the .
1
: 2 9
0
7
9
3 4 :
:
2
E
0
1
7
0 5 :
0 :
4
3
0
:
0
0
:
1 E
5
0
1
0
B
W N
W
3 3
0 0
1
C
R e v .
1
0 0
0
0
M A
0
-
8
1
7
R Q 0 4
1
0
- 0 0
0
8
2
Figure 1-3 Nonport Side, Viewed from Top
1
2
Top of switch
Connection ports
Labeling
Figures 1-4 and 1-5 show the labels appearing on the SilkWorm 4016. A second serial label is located
beneath the insertion arm on the chassis, visible only when the arm is extended.
To extend the insertion arm, gently squeeze the plastic tab (top-to-bottom) and pull outward.
84-0000123-01 Rev X
XXX 10:00:00:05:1E:34:70:29
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
1-5
1
Switch Characteristics
Figure 1-4 Insertion Arm Label
1
2
5
4
3
Figure 1-5 Detail, Labeling
1
2
3
4
5
Supplier serial label (under insertion arm)
Compliance label
Service tag
PPID label
Service tag and PPID label
SFPs
The SilkWorm 4016 was designed to work with small form-factor pluggable (SFP) optical modules and
ships with up to six SWL SFPs. SFPs provide optical connections to external devices for both SWL and
LWL connections. SFPs are replaced using a new pluggable unit rather than having to replace the
switch. Refer to the manufacturer’s instructions when installing SFPs.
“Removing and Replacing the SilkWorm 4016” on page 4-5 provides details about removing SFPs from
the SilkWorm 4016.
For a complete list of SFPs and other interoperable hardware, visit the Brocade Connect Web site at:
and follow the links to the latest compatibility matrix. From the main page, select Technical Resource
Center, then Documentation Library. Finally, choose Compatibility and Scalability Information.
1-6
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
1
ISL Trunking Groups
ISL Trunking Groups
Brocade ISL Trunking is optional software that allows you to create trunking groups of ISLs between
adjacent switches.
If your SilkWorm 4016 switch has a Brocade ISL Trunking license, the external ports can be used as a
trunking group. Ports that can be used within the same trunking group are color-coded on the switch’s
port side for easy identification.
possibilities for the SilkWorm 4016. These groups correspond with external port groups.
,
Table 1-4
ISL Trunking Group Options
# Active Ports
External Port #
Trunking groups
External: 4
Internal: 8
10, 11, 12, 13
10+11, 10+12, 10+13, 10+11+12, 10+11+13,
10+12+13, 11+12+13, 10+11+12+13
(any 2, 3, or 4 ports can be trunked together)
External: 6
Internal: 10
10, 11, 12, 13, 14, 15 10+11, 10+12, 10+13, 10+11+12, 10+11+13,
10+12+13, 11+12+13, 10+11+12+13, 14+15
(any 2, 3, or 4 ports from the 10 to 13 group of ports
and one two port trunk with 14+15 2-port trunk)
.
Note
Only the external ports are available for trunking.
The external ports can be used to form 2-port trunks, 3-port trunks, or a 4-port trunk. Trunking groups
are color-coded on the port side of the chassis for easy identification.
For details about Brocade ISL Trunking, see the Brocade Fabric OS Administrator’s Guide.
Brocade Optional Features
The SilkWorm 4016 supports the following optional Brocade software, which is activated with the
purchase of the corresponding license key:
•
•
•
•
Brocade Advanced Web Tools1
Brocade Advanced Zoning1
Brocade ISL Trunking
•
•
•
•
Brocade Fabric Watch
Brocade Secure Fabric OS
Port on Demand (POD) licensing
Brocade Advanced Performance
Monitoring
Support for Brocade Fabric Access API and API
Scripting Toolkit
1. included with the SilkWorm 4016
For detailed information on any of these features, refer to the Fabric OS Administrator’s Guide.
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
1-7
1
Brocade Optional Features
1-8
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
Chapter
Installing the Brocade SilkWorm 4016
2
This chapter provides the following information:
•
•
•
Unpacking the SilkWorm 4016
To remove the SilkWorm 4016 from its shipping package:
1. Open the shipping box and inspect the contents, making sure that nothing is missing or damaged.
Do not insert a damaged switch into the PowerEdge chassis. If the SilkWorm 4016 appears to be
damaged, contact your sales representative before proceeding.
2. Remove the cardboard accessory tray that sits on top of the SilkWorm 4016.
This tray contains the documentation, regulatory statements, product information guide, and
Documentation CD.
3. Remove the switch from the box.
The protective foam ends will slide out with the switch.
4. Remove the foam ends from the switch.
5. Be sure that you have taken the necessary precautions for electrostatic sensitivity; then, break the
seal warning.
6. Slide the SilkWorm 4016 out of the antistatic sleeve and inspect it carefully for any obvious defects
or shipping damage.
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
2-1
2
Preparing the Blade Server for the SilkWorm 4016
Preparing the Blade Server for the SilkWorm 4016
Before you insert the SilkWorm 4016 into the blade server chassis, make sure that the following
conditions are met:
•
•
The blade server chassis is powered up.
The I/O bay into which the SilkWorm 4016 will be inserted is empty and ready to receive the
switch. The SilkWorm 4016 should only be inserted into the specific chassis I/O bay indicated.
•
•
All power requirements specific to the blade server chassis are met. Refer to the manufacturer’s
documentation for details.
If you are replacing an existing switch, the new one should be inserted within one minute of
removal.
Inserting a SilkWorm 4016 into the Chassis
To insert the SilkWorm 4016 into a blade server chassis:
2. Verify that the chassis I/O bay into which the SilkWorm 4016 is being inserted is empty. Do not
insert the SilkWorm 4016 into any other chassis I/O bay.
3. Gripping the top and bottom of the release latch, gently squeeze the latch to free the insertion arm.
The SilkWorm 4016 is designed to work only in the designated chassis I/O bay of the blade server.
A
C
R
10
11
B
A
Top of latch
B
C
Bottom of latch
Insertion arm
2-2
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
2
Inserting a SilkWorm 4016 into the Chassis
4. Swing the insertion arm out to open the arm completely.
This positions the insertion arm, allowing the SilkWorm 4016 to seat properly in the blade server
chassis.
84-0000123-01 Rev
X
XXX 10:00:00:05:1E:34:70:29
5. With the port side facing you and the insertion arm extended, slide the SilkWorm 4016 into the
open chassis I/O bay. The following illustration shows the SilkWorm 4016 being inserted with a
horizontal orientation. Your blade server chassis may reuqire a vertical orientation.
NTE
1
3
1
2
1
NTE
1
1
3
3
1
2
1
PSU
1
1
1
0
1
!
s
e
t
u
in
m
2
in
h
it
w
ced
la
p
e
r
e
b
st
u
m
ule
d
o
m
N
A
F
NTE
2
PUS
I
N
1
!
s
e
4
t
inu
m
2
n
hi
it
w
ced
la
PUS
p
e
r
e
b
st
u
4
le
u
m
d
o
m
N
FA
OIO
I
PUS
2
3
1
2
!
6. Push the insertion arm gently toward the chassis until the arm is flush with the edge of the
SilkWorm 4016 chassis.
At this point the SilkWorm 4016 is firmly seated in the chassis I/O bay.
Warning
Do not force the arm closed. Doing so could cause damage. If the arm does not close easily, gently
remove the SilkWorm 4016 and reinsert it into the chassis I/O bay.
Closing the insertion arm locks the SilkWorm 4016 into the chassis I/O bay. Locking the
SilkWorm 4016 into the bay activates the switch and switch LEDs.
7. Install the SFP modules into the external ports.
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
2-3
2
Inserting a SilkWorm 4016 into the Chassis
Refer to the SFP manufacturer’s documentation for details about SFP modules.
After it is activated, the switch runs self-diagnostic tests such as POST. For more information, see
“Interpreting POST Results” on page 4-3. After the diagnostics are complete, cable the SilkWorm 4016
as directed by the blade server chassis manufacturer’s documentation. The blade server creates a
connection to the switch for configuration.
address for the switch module.
2-4
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
Chapter
Configuring the Brocade SilkWorm 4016
3
The SilkWorm 4016 must be configured correctly before it can operate within a network and fabric.
This chapter provides the following information to ensure successful configuration:
•
•
•
Items Required
The following items are required for configuring and connecting the SilkWorm 4016 for use in a
network and fabric:
•
•
•
•
•
•
The SilkWorm 4016, installed in a blade server chassis
A workstation computer that has a terminal emulator (such as HyperTerminal)
An unused IP address and corresponding subnet mask and gateway address
The serial cable to connect to the blade server chassis
SFP transceivers and compatible fibre cables, as required
Access to an FTP server for backing up the switch configuration
Configuring the SilkWorm 4016
To configure the SilkWorm 4016, perform the tasks in the order shown:
Caution
Do not connect the switch to the internal network until the IP address is correctly set.
1. Install the SilkWorm 4016 in a blade server chassis as described in “Inserting a SilkWorm 4016 into
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
3-1
3
Configuring the SilkWorm 4016
Creating a Serial Connection
To create a serial connection to the SilkWorm 4016 you need to connect to the serial port of the blade
server chassis’ management module.
Note
All versions of the Microsoft Windows operating system include Hilgraeve's HyperTerminal terminal
emulation software. However, the included version does not provide many functions required during
console redirection. Either upgrade to HyperTerminal Private Edition 6.3, or select new terminal
emulation software.
The examples in this section assume that you have upgraded to Hilgraeve's HyperTerminal Private
Edition 6.3. (Only Hilgraeve's HyperTerminal Private Edition 6.3 using Windows Server 2003 is
supported.) If you are using other terminal emulation software, see the documentation for that software.
When using HyperTerminal with the Microsoft Windows 2000 operating system, ensure that you have
Windows 2000 Service Pack 2 or later installed. The arrow keys function properly in HyperTerminal’s
VT100 emulation with Windows 2000 Service Pack 2.
1. Connect the null modem cable to the serial port on the management module and to the client
system.
2. Click the Start button, point to Programs > Accessories > Communications, and then click
HyperTerminal.
3. Enter a name for the new connection, select an icon, and then click OK.
4. From the Connect to drop-down menu, select an available COM port, and then click OK.
After you select an available COM port, the COM port properties window appears.
5. Configure the port with the following settings:
Bits per second 115200
Data bits
Parity
8
None
Stop bits
Flow control
Properties
1
None
VT100 for Emulation mode
Terminal keys1 Function, Arrow, and Ctrl
1. Ensure that the setting is not set to Windows keys
6. Click OK.
The management application displays a login screen on the console monitor.
7. Log into the management module using your administrative user name and password.
For details about setting up the terminal emulation with the correct connection and login information,
refer to the blade server chassis documentation.
3-2
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
3
Configuring the SilkWorm 4016
Connecting to the Switch
To log in to the switch through the serial connection:
1. Verify that the switch has completed POST. When POST is complete, the port status and switch
power and status LEDs return to a standard healthy state.
3. At the command prompt, type connect switch-x where x is the bay into which the SilkWorm 4016
is installed.
4. At the login prompt, log in to the SilkWorm 4016 switch. By default, the user name is “admin” and
the password is “password”.
Setting the Switch IP Address
By default, the IP address for the SilkWorm 4016 is configured as 10.77.77.77.
To replace the default IP address and related information:
1. Log in using the terminal emulator and enter the ipAddrSet command. Follow the on-screen
instructions and supply the correct information, as shown in the following example.
switch:admin> ipaddrset
Ethernet IP Address [10.77.77.77]:10.32.53.47
Ethernet Subnetmask [255.0.0.0]:255.255.240.0
Fibre Channel IP Address [0.0.0.0]:
Fibre Channel Subnetmask [0.0.0.0]:
Gateway IP Address [0.0.0.0]:10.32.48.1
Set IP address now?[y = set now, n = next reboot]:y
IP address being changed...
Committing configuration...Done.
switch:admin>
2. Optionally, verify that the address was correctly set by typing the ipAddrShow command at the
prompt.
Creating an Ethernet Connection
To create an Ethernet connection to the SilkWorm 4016:
1. Remove the dust plug from the Ethernet port.
2. Connect an Ethernet cable to the switch Ethernet port and to the workstation or to an Ethernet
network containing the workstation.
Note
At this point the switch can be accessed remotely. Ensure that the switch is not being modified from any
other connection until configuration is complete.
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
3-3
3
Configuring the SilkWorm 4016
Completing the Switch Configuration
To complete the switch configuration:
1. Log on to the switch by telnet, using the admin account.
2. Modify the domain ID if required.
The default domain ID is 1. If the switch is not powered on until after it is connected to the fabric
and the default domain ID is already in use, the domain ID for the new switch is automatically reset
to a unique value. If the switch is connected to the fabric after is has been powered on and the
default domain ID is already in use, the fabric segments.
To find the domain IDs that are currently in use, run the fabricShow command on another switch in
the fabric. Identify an unused domain ID:
a. On the SilkWorm 4016 that is being configured, disable the switch using the switchDisable
command.
b. Enter the configure command.
The command prompts display sequentially; enter a new value or press Enter to accept each
default value. The SilkWorm 4016 now has a unique domain ID and can join the fabric.
c. Reenable the switch by entering the switchEnable command.
Note
It could take a short time (typically a few seconds but sometimes a little longer) for the
newly added switch to appear in the fabric display with its newly assigned domain ID.
3. Install the SFP transceivers in the external Fibre Channel ports as required.
a. Remove the dust plugs from the ports to be used.
b. If necessary, remove the end caps from the SFP.
c. Position a transceiver so that it is oriented correctly and insert it into a port until it is firmly
seated and the latching mechanism clicks.
For instructions specific to the type of transceiver, refer to the transceiver manufacturer’s
documentation.
d. Repeat substeps a, b, and c for the remaining ports, as required.
3-4
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
3
Configuring the SilkWorm 4016
4. Connect the cables to the transceivers.
The transceivers are keyed to ensure correct orientation. If a transceiver does not install easily,
ensure that it is correctly oriented and that the end caps have been removed. The cables used in
trunking groups must meet specific requirements. For a list of these requirements, see the Fabric
OS Administrator’s Guide.
Caution
A 50-micron cable should not be bent to a radius less than 2 inches under full tensile load
and 1.2 inches with no tensile load.
Tie wraps are not recommended for optical cables because they are easily overtightened.
a. Orient a cable connector so that the key (the ridge on one side of connector) aligns with the slot
in the transceiver.
b. Insert the cable into the transceiver until the latching mechanism clicks. For instructions
specific to cable type, refer to the cable manufacturer’s documentation.
c. Repeat for the remaining transceivers as required.
5. Check the LEDs to verify that all components are functional.
6. Verify the correct operation of the SilkWorm 4016 by typing the switchShow command from the
workstation.
This command provides information about switch and port status.
7. Verify the correct operation of the SilkWorm 4016 in the fabric by typing the fabricShow
command from the workstation.
This command provides general information about the fabric.
8. Back up the switch configuration to an FTP server by typing the configUpload command and
following the prompts.
This command uploads the switch configuration to the server, making it available for downloading
to a replacement switch if necessary. Brocade recommends backing up the configuration on a
regular basis to ensure that a complete configuration is available for downloading to a replacement
switch.
For specific instructions about how to back up the configuration, see the Fabric OS Administrator’s
Guide. The switchShow, fabricShow, and configUpload commands are described in detail in the
Fabric OS Command Reference Manual.
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
3-5
3
Activating Ports on Demand (POD)
Activating Ports on Demand (POD)
The SilkWorm 4016 is shipped with 12 licensed ports. As your needs increase, you can activate up to
four additional ports by purchasing and installing the Brocade Ports on Demand (POD) optional
Table 3-1
Ports available
Port Licensing
Base
External Ports
10 through 13
14, 15
Internal Ports
0 through 7
8, 9
POD
Adding licenses is performed using either Brocade Web Tools or a telnet connection: you do not use the
blade server chassis’ management software.
Ports on Demand is ready to be unlocked in the switch module firmware. Its license might be supplied
with switch module software, or you can purchase the license separately from your switch module
vendor, who will provide you with a key to unlock it.
Once you have installed the license keys, you must enable the ports. You can do so without disrupting
switch operation, or alternatively, you can disable and reenable the switch to activate all ports.
If you remove a Ports on Demand License, the ports that were enabled by that license are disabled.
Activating Ports with a POD License
There are two methods for activating ports with a POD license:
1. For switch modules connected to existing storage networks:
•
•
Add the POD license using Web Tools or CLI.
Enable each newly licensed ports using Web Tools or CLI.
This method is non-disruptive to existing servers and storage connecting to switch module.
2. For new switch module installs, perform the following before connecting to an existing SAN.
Caution
Do not use this method if the switch module is operating in an existing SAN because
traffic will be disrupted.
•
•
Disable the switch module and then add the POD license using Web Tools or the CLI.
If Secure Fabric OS (Secure FOS) is enabled you cannot use telnet or SSH to disable the
module. For details about using Web Tools, refer to the Web Tools Administrator’s Guide. For
details about the CLI, see the Fabric OS Command Reference Manual.
Enable the switch using Web Tools or CLI. When the switch is enabled, the newly-added POD
ports are also enabled.
3-6
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
3
Connecting to the Switch Using Web Tools
Removing POD-licensed Ports
You can return the switch module to the default number of ports by removing the POD license. The
license can be removed regardless of whether the switch is active or disabled.
Use Web Tools or the CLI to remove the POD license. Ports should be disabled before removing a POD
license.
For details about using Web Tools, see the Web Tools Administrator’s Guide. For details about the CLI
and CLI commands, see the Fabric OS Command Reference Manual.
•
•
If the switch module is disabled, the removed ports are not automatically enabled when the switch
module is enabled.
If the switch module is enabled when a license is removed, operations continue until the switch
module receives either a switchDisable/Enable command, the switch module is power cycled, or
you perform a manual portDisable of each unlicensed port.
In the following example, ports that were enabled under a POD license (ports 17, 18, and 19) are
disabled and the POD license is removed.
Example, using the CLI
switch:admin > portdisable 17
switch:admin > portdisable 18
switch:admin > portdisable 19
switch:admin > licenseremove "RRySeyRcySSS3TfS"
Connecting to the Switch Using Web Tools
To connect to the switch using Brocade’s Web Tools:
1. On the management console, open a Web browser such as Internet Explorer.
The Web browser must be connected to the same network as the switch.
2. Enter the IP address of the switch in the address field and press Enter.
For more information about using Web Tools, see the Web Tools Administrator’s Guide.
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
3-7
3
Connecting to the Switch Using Web Tools
3-8
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
Chapter
Operating the Brocade SilkWorm 4016
4
This chapter describes the operation and interoperability of the SilkWorm 4016. Included in this chapter
are:
•
•
•
•
•
Interoperability
The SilkWorm 4016 supports interoperability for:
•
•
•
•
•
link initialization
•
•
•
•
•
soft WWN zoning
principal switch selection
routing (FSPF)
SNMP facilities
translative mode (private target support on fabrics)
trunking (between two Brocade switches)
Advanced Performance Monitoring
Simple Name Service
state change notification
Table 4-1
Switch
Compatible Switches
Minimum Version
4.2.1
Switch
Minimum Version
SilkWorm 3014
SilkWorm 3200
SilkWorm 3250
SilkWorm 3800
SilkWorm 3850
SilkWorm 3900
SilkWorm 4100
SilkWorm 12000
SilkWorm 24000
SilkWorm 48000
SilkWorm 200E
4.4.0
4.2.0
4.2.0
5.0.1a
5.0.1a
3.1.2
4.2.0
3.1.2
4.2.0
4.2.0
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
4-1
4
Accessing the SilkWorm 4016
Port Negotiation
The SilkWorm 4016 has been designed to be highly interoperable. It supports 1 Gbit/sec, 2 Gbit/sec,
and 4 Gbit/sec transmit and receive rates with autonegotiation. The actual data signaling rate used on a
port is automatically sensed and set to the rate supported by device or devices attached to the port.
If the SilkWorm 4016 is connected to a device but is unable to negotiate the signaling rate, the operator
can manually set the speed of each port through the management interfaces.
The SilkWorm 4016 is compliant with current Fibre Channel standards, including most current-
generation switch N_Ports, NL_Ports, and E_Ports as well as host adapters, Redundant Array of
Independent Disks (RAID) storage devices, hubs, Fibre-SCSI bridge devices, and older Brocade
SilkWorm switch families.
Operating System Support
Brocade Fabric OS has no specific host OS dependencies. The Fabric OS in the switches allows for any
Fibre Channel-compliant device to attach to the switches as long as it conforms to the standards for
device login, name service, and related Fibre Channel features. The operating systems listed in Table 4-
2 are for the host machine running Brocade management applications outside the Fabric OS, such as
Fabric Manager.
Table 4-2
Supported Operating Systems
Operating System
AIX
Version
4.3.3
Windows NT
Windows 2000
Solaris
4.0
Initial Release
2.5, 2.5.1, 2.6, 2.7, 2.8
10.0, 11.0
HP UX
Linux
Red Hat versions 6.2 and 7.0
Accessing the SilkWorm 4016
The SilkWorm 4016 is managed as a single element. It has a single IP address and appears as a separate
entity to the telnet protocol and the Simple Network Management Protocol (SNMP).
When SNMP devices send SNMP messages to a management console running SAN management
software, the information is stored in a Management Information Base (MIB). The SilkWorm 4016
Fabric OS 4.4.1 supports the FibreAlliance Fibre Channel Management (FCMGMT) MIBs, allowing
the provision of needed information to a SAN administrator.
In addition, the Brocade Fabric Access Layer (API) and the Storage Management Initiative (SMI)
provide facilities for the discovery and management of physical and logical elements in a SAN. Using
the Fabric Access interface to the Fabric OS, a client application can retrieve information and modify
the configuration of Brocade switches in the fabric.
4-2
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
4
Interpreting POST Results
Secure telnet access is available using Secure Shell (SSH), a network security protocol for secure
remote login and other secure network services over an insecure network.
Brocade Web Tools management is available via a secure browser using Secure Sockets Layer (SSL).
The SSL security protocol provides data encryption, server authentication, message integrity, and
optional client authentication for a TCP/IP connection. Because SSL is built into all major browsers and
Web servers, installing a digital certificate enables the SSL capabilities.
Interpreting POST Results
The power-on self test (POST) system check is performed each time the switch is powered on, rebooted,
or reset.
Example POSTOutput
POST1: Started running Tue Nov 9 20:27:57 GMT 2004
POST1: Test #1 - Running turboramtest
POST1: Test #2 - Running centralmemorytest
POST1: Test #3 - Running cmitest
POST2: Running diagshow
POST1: Script PASSED with exit status of 0 Tue Nov 9 20:28:10 GMT 2004 took (0:
0:13)
POST2: Started running Tue Nov 9 20:28:12 GMT 2004
POST2: Test #1 - Running camtest
POST2: Test #2 - Running txdpath
POST2: Test #3 - Running spinsilk (SERDES)
POST2: Running diagshow
POST2: Script PASSED with exit status of 0 Tue Nov 9 20:29:11 GMT 2004 took (0:
0:59)
Initializing Ports ....
Port Initialization Completed
Enabling switch...
During POST, the LEDs are activated in various indicator patterns.
To determine POST completion status:
•
Verify that the LEDs on the switch indicate a healthy SilkWorm 4016. LED patterns are described
If one or more LEDs do not display a healthy state, verify that the LEDs are not set to beacon. Use
the switchShow command or Web Tools to verify the LED state. For information about how to turn
beaconing on and off, see the Fabric OS Administrator’s Guide or the Web Tools Administrator’s
Guide.
•
•
Use the blade server chassis’ management module to verify that the switch is working correctly.
Refer to the blade server chassis documentation for details.
Review the system log for errors.
Any errors detected during POST are written to the system log. Access this log through the
errShow command. For information about this command, see the Fabric OS Command Reference
Manual. For information about error messages, see the Fabric OS System Error Message Reference
Manual.
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
4-3
4
Interpreting LED Activity
Interpreting LED Activity
the two LEDs adjacent to each SFP, with one LED to indicate port speed and one LED to indicate
activity.
6
7
1
2
10
11
12
13
14
15
3
!
5
4
Figure 4-1 LED Locations
Location
Indicator Color
Operation
1
bladeserver green/amber
chassis
Controlled by the blade server. Refer to the blade
serverdocumentation for details.
2
status
green/amber
•
Off: Switch is off or both power supplies from the
PowerEdge 1855) or onboard DCC have failed
•
•
Green: No errors and all ports are ready for use
Amber: Boot-up state, port(s) offline, or in reset
state
•
Blinking (2 Hz green/amber): One or more
environmental ranges are exceeded, or error log
contains diagnostic error messages
Note: The LED might blink during testing.
3
power
green
•
•
Off: Switch is off or both power supplies (on the
PowerEdge 1855) or onboard DCC have failed
Green: Normal operation and power supply is
functioning properly. Power is supplied by the
blade server chassis
4-4
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
4
Removing and Replacing the SilkWorm 4016
Location
Indicator Color
Operation (Continued)
4
Ethernet
speed
green
•
•
Off: 10 Mbit/sec
On: 100 Mbit/sec
5
6
Ethernet
link
amber
•
•
•
Off: No link
On: Link OK
Blink: Rx or Tx traffic
FC port x
status
green/amber
LED meanings are not valid during boot, diagnostics,
or POST.
•
•
•
•
Off: No signal carrier
Amber: Signal present but not online
Slow blink amber: Disable, ~2 second interval
Fast blink amber: Error or fault with port, ~1/2
second interval
•
•
•
Green: Online; flickers with activity
Slow blink green: Online but segmented
Fast blink green: Internal loopback
7
FC port x
speed
green/amber
•
•
•
Amber on: 4 Gbit/sec FC
Green on: 2 Gbit/sec FC
Both off: 1 Gbit/sec FC
Removing and Replacing the SilkWorm 4016
To remove a failed or replaced SilkWorm 4016:
1. Back up the switch configuration to an FTP server by typing the configUpload command and
following the prompts.
This command uploads the switch configuration to the server, making it available for downloading
to a replacement switch if necessary. Brocade recommends backing up the configuration on a
regular basis to ensure that a complete configuration is available for downloading to a replacement
switch.
2. Stop all SAN activity requiring the ports used by the SilkWorm 4016.
For details about port management, refer to your blade server documentation. Verify that there is no
activity by viewing the SilkWorm 4016 LEDs. For details about LED activity on the SilkWorm
3. Remove all cables from the SFP modules.
4. Remove the SFP modules according to the manufacturer’s instructions.
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
4-5
4
Removing and Replacing the SilkWorm 4016
The following figure details the generic process for removing an SFP from a port.
Cable
Release
Bale
SFP
1
3
SFP
4
2
5. Squeeze the release lever latch to release the SilkWorm 4016.
Squeeze
R
10
Squeeze
11
4-6
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
4
Removing and Replacing the SilkWorm 4016
6. Gently pull the handle of the SilkWorm 4016 insertion arm out and toward you to release the
switch.
.
84-0000123-01 Rev.X
||||| |||| |||||||| |||||||| |||||||| ||||
RP040000111
7. Slide the switch out of the chassis I/O bay. In the following illustration the SilkWorm 4016 is
inserted in a horizontal oprientation. Other blade server chassis may require a vertical orientation.
NTE
1
3
1
2
1
NTE
1
1
3
3
1
2
1
PSU
1
1
1
0
1
!
s
e
t
u
n
i
m
2
n
hi
t
i
w
d
ce
a
l
p
e
r
e
b
st
u
e
m
l
u
d
o
m
N
A
F
NTE
2
PUS
NTE
1
!
s
e
4
t
nu
i
m
2
hin
t
i
w
ced
la
PUS
p
re
e
b
st
u
4
e
m
l
u
od
m
N
FA
I
I
PUS
2
3
1
12
!
8. Within one minute, install a replacement switch or a filler module into the empty slot.
The replacement procedure is described in detail in “Inserting a SilkWorm 4016 into the Chassis”
Note
If you are not replacing the switch, use a filler module to fill the empty slot to ensure
proper air flow. Do not leave the slot empty for longer than one minute.
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
4-7
4
Removing and Replacing the SilkWorm 4016
4-8
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
Appendix
Brocade SilkWorm 4016 Specifications
A
This appendix provides product specifications as a handy reference. Information provided here includes:
•
•
•
•
•
•
Weight and Physical Dimensions
Table A-1 lists the weight and physical dimensions of the SilkWorm 4016.
Table A-1 Switch Specifications
SilkWorm 4016
1.27 in (32.2 mm)
Height
Width
Depth
Weight
5.13 in (130 mm)
10 in (254 mm)
2.32 lb — without media
Facility Requirements
The information in Table A-2 shows the operating and non-operating limitations of the SilkWorm 4016.
Table A-2
Condition
Temperature
Humidity
Environmental Requirements
Operating
Non-operating
0°C to 40°C (32°F to 104°F)"
-20°C to 70°C (-4°F to 158°F)"
10% to 90%, non-condensing at 5% to 95%, non-condensing at
29°C" 38°C"
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
A-1
A
Architectural Specification
Table A-2
Altitude
Shock
Environmental Requirements (Continued)
Up to 3,048 m (10,000 ft)
Up to 10.668 km (35,000ft)
20G for 6ms
50G with a velocity change of
4216 mm/sec squared
Vibration
Air flow
0.4G at 5 Hz to 500 Hz for 60
minutes
0.5G at 2 Hz to 200 Hz for 15
minutes; 1.04 GRMS Random for
15 minutes
Normal: 100-300 LFM
None required
Architectural Specification
Table A-3 Architecture
Scalability
Full fabric architecture with maximum of 239 switches
Certified maximum
Performance
32 switches, 7 hops
1.063 Gbit/sec line speed, full duplex
2.125 Gbit/sec line speed, full duplex
Fabric latency
<2.1 µsec with no contention
2112-byte payload
Maximum frame size
Class of service
Class 2
Class 3
Class F (interswitch frames)
Port types
FL_Port
F_Port
E_Port
Fabric services
Simple Name Server, Registered State Change Notification
Supported HBAs
A complete list of interoperable hardware, visit the Brocade Connect Web site at:
and follow the links to the latest compatibility matrix. From the main page, select Technical Resource
Center, then Documentation Library. Finally, choose Compatibility and Scalability Information.
For more information and a list of supported HBAs, refer to your Dell PowerEdge documentation.
A-2
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
A
Fibre Channel Standards Compliance
Fibre Channel Standards Compliance
The SilkWorm 4016 switch meets or exceeds the Fibre Channel standards compliance, performance, and
feature capabilities as defined in the Brocade standards compliance list. This information is available at:
Regulatory Compliance
This section describes the regulatory compliance requirements for the SilkWorm 4016. It contains:
•
•
•
•
•
•
•
•
•
•
FCC Warning (US only)
This equipment has been tested and complies with the limits for a Class A computing device pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in
accordance with the instruction manual, might cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference, in which case the
user will be required to correct the interference at the user’s own expense.
MIC Statement (Republic of Korea)
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
A-3
A
Regulatory Compliance
VCCI Statement
This is a Class A product based on the standard of the Voluntary Control Council for Interference by
Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio
disturbance might arise. When such trouble occurs, the user might be required to take corrective actions.
BSMI Statement (Chinese)
A-4
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
A
Regulatory Compliance
CE Statement
Caution
This is a Class A product. In a domestic environment, this product might cause radio interference, and
the user might be required to take corrective measures.
The standards compliance label on the SilkWorm 4016 contains the CE mark which indicates that this
system conforms to the provisions of the following European Council directives, laws, and standards:
•
Electromagnetic Compatibility (EMC) Directive 89/336/EEC and the Complementary Directives
92/31/EEC and 93/68/EEC
•
•
Low Voltage Directive (LVD) 73/23/EEC and the Complementary Directive 93/68/EEC
EN50082-2/EN55024:1998 (European Immunity Requirements)
-
-
EN61000-3-2/JEIDA (European and Japanese Harmonics Spec)
EN61000-3-3
Canadian Requirements
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations, ICES-003 Class A.
Laser Compliance
This equipment contains Class 1 laser products and complies with FDA Radiation Performance
Standards, 21 CFR Subchapter I and the international laser safety standard IEC 825-2.
Caution
Use only optical transceivers that are qualified by Brocade Communications Systems, Inc. and comply
with the FDA Class 1 radiation performance requirements defined in 21 CFR Subchapter I, and with
IEC 825-2. Optical products that do not comply with these standards might emit light that is hazardous
to the eyes.
RTC Battery
Caution
Do not attempt to replace the real-time clock (RTC) battery. There is danger of explosion if the battery is
incorrectly replaced or disposed of. Contact your switch supplier if the real-time clock begins to lose
time.
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
A-5
A
Regulatory Compliance
Electrical Safety
Caution
This switch might have more than one power cord.To reduce the risk of electric shock, disconnect both
power cords before servicing.
Caution
Connect the power cord only to a grounded outlet.
Caution
This product is designed for an IT power system with phase-to-phase voltage of 230V. After operation of
the protective device, the equipment is still under voltage if it is connected to an IT power system.
Regulatory Certifications
Table 4-3 lists the safety and EMC (electromagnetic compatibility) specifications for which the
SilkWorm 4016 is certified.
Table 4-3
Country
Canada
EMC Certifications
Safety Specification
EMC Specification
CSA 22.2 No. 60950 Third Ed.
CSA 108.8 Class A
United States
UL 60950 Third Ed., Info. Tech. Equip.
EN55022 Class A
FCC Part 15, Subpart B (CFR title 47), Class A
A-6
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
A
Regulatory Compliance
Table 4-3
Country
Japan
EMC Certifications (Continued)
Safety Specification
EMC Specification
IEC 60950+A1+A2+A3+A4+A11
EN55022 Class A
EN 61000-3-2 Harmonics (JEIDA Limits)
EN55022 Class A
International
IEC 60950+A1+A2+A3+A4+A11
European Union
EN 60950:92
EN 55022:1998 Class A
+A1:93+A2:93+A3:95+A4:96+A11:97
(Austria, Belgium, Cyprus,
Czech Republic, Denmark,
Estonia, Finland, France,
Germany, Greece, Hungary,
Ireland, Italy, Latvia,
Lithuania, Luxembourg,
Malta, Poland, Portugal,
Slovakia, Slovenia, Spain,
Sweden, The Netherlands,
United Kingdom)
EN 55024 (Immunity)
73/23/EEC
EN 61000-4-2 Electrostatic Discharge
EN 61000-4-3 Radiated Fields
EN 61000-4-4 Electrical Fast Transients
EN 61000-4-5 Surge Voltage
EN 61000-4-6 Conducted Emissions
EN 61000-4-8 Magnetic Fields
EN60825-1:1994/A11, -2
TUV (Germany only)
IEC 60950+A1+A2+A3+A4+A11
(NEMKO CB Report) (Norway only)
and Republic of Korea
EN 61000-4-11 Voltage Dips and Interruptions
EN 61000-3-2 Limits for Harmonic Current
Emissions
EN 61000-3-3 Flicker
Australia and New Zealand
EN 55022: 1998 Class A
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
A-7
A
Regulatory Compliance
A-8
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
Index
A
D
accessing 4-2
activating ports 3-6
air flow A-1
digital thermometer 1-2
dimensions of 1-3
DTE port 1-1
B
E
E_Ports 1-1
beacon 4-3
boot flash 1-3
Brocade applications supported 1-7
Brocade ISL Trunking 1-7
BSMI statement (Chinese) A-4
electrical safety A-6
errShow command 4-3
Extended Fabrics 1-7
external port groups 1-7
F
C
F_Ports 1-1
Canadian requirements A-5
CE statement A-5
commands
Fabric Watch 1-7
fabricShow command 3-5
facility requirements A-1
FCC warning (US only) A-3
features 1-1, 1-7
Fibre Channel Standards Compliance A-3
filler module 4-7
configUpload 3-5
connect 3-3
errShow 4-3
fabricShow 3-5
ipAddrSet 3-3
ipAddrShow 3-3
portDisable 3-7
switchDisable 3-7
switchEnable 3-7
switchShow 3-5, 4-3
compact flash 1-3
compatibility matrix 1-6
configUpload command 3-5
connect command 3-3
console port 1-1
FL_Ports 1-1
flash 1-3
H
humidity A-1
I
inserting 2-2
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
Index-1
insertion arm 1-5, 2-2
insertion arm latch 2-2
installation 2-2
N
nonport side 1-5
interfaces 1-1
Internet Explorer 3-7
interoperability 4-1
interpreting
O
operating requirements A-1
Operating System support 4-2
optional features 1-7
LED activity 4-4
POST results 4-3
ipAddrSet command 3-3
ipAddrShow command 3-3
ISL 1-7
trunking 1-1, 1-7
trunking groups 1-7
ISL trunking 1-7
P
Performance Monitor 1-7
POD,port licensing 3-6
port groups 1-7
ISL trunking groups 1-7
K
port negotiation 4-2
kernel 1-3
port side 1-4
kernel flash 1-3
Port Side of the SilkWorm 3014 1-4
port speed 1-1
portDisable command 3-7
ports
L
base 1-3, 3-6
Ports on Demand 3-6
POST 1-1, 2-4, 4-3
POST results 4-3
PPC405GP 1-2
preparing the PowerEdge 1855 2-2
processor 1-2, 1-3
protective foam 2-1
prots
labeling 1-5
laser compliance A-5
latch 2-2
LED activity
interpreting 4-4
license
removing 3-7
license key 3-6
activating 3-6
R
M
real-time clock 1-2
Management tool 4-3
memory 1-3
MIC statement (Republic of Korea) A-3
regulatory certifications A-6
regulatory compliance A-3
release lever 2-2
remote switch 1-7
Index-2
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
removing and replacing 4-5
removing POD license 3-7
replacement 2-2, 4-2
RJ-45 connector 1-1
V
VCCI statement A-4
vibration A-1
RTC battery A-5
W
S
Web browser 3-7
Web Tools 3-7
SDRAM 1-3
weight 1-3, A-1
Weight and Physical Dimensions 1-3
SEEPROM 1-2, 1-3
SFPs 1-6
shipping package 2-1
shock A-1
SilkWorm 3014 Features 1-1
SilkWorm 3014 Memory 1-3
slots 2-2
Z
zoning 1-1, 1-7, 4-2
specifications A-1
status 1-2, 4-4
Supported (Optional) Features 1-7
supported HBAs A-2
switch
characteristics 1-3
physical dimensions 1-3
weight 1-3
switchDisable command 3-7
switchEnable command 3-7
SWL 1-1, 1-6
T
temperature A-1
temperature sensor 1-2
trunking 1-7
U
unpacking the SilkWorm 3014 2-1
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
Index-3
Index-4
SilkWorm 4016 Hardware Reference Manual
Publication Number: 53-1000175-01
|