Freestyle 1050
Combined Cordless Telephone & Digital Answering Machine
User Guide
This equipment is not designed for making emergency telephone calls when the power
fails. Alternative arrangements should be made for access to emergency services.
Please open this page for an ‘at a glance’
guide to your Freestyle 1050.
At a glance
Aerial
Does not extend.
See page 5
Talk
Press to get a dialling tone and to
end a call.
In Use / Battery Low
See page 8
Comes on when the handset is in
use or, if the handset is on
standby, to indicate the battery
needs recharging.
Channel
Enables you to change the
channel if there is interference
on your call.
See page 9
Secrecy / Screen
For Secrecy: when pressed
during a call, the caller cannot
hear you.
P
Inserts a pause when dialling
a number.
For Screen: allows you to hear a
caller leaving a message through
your handset. You can then
choose to take the call or not.
Also operates the answer
machine functions.
See page 11
Recall
For use with some
BT Select Services and when
connected to a switchboard.
See page 11
See page 9, 18
Keypad
Quickdial memory
Allows you to store and dial up to
10 numbers in the memory.
See page 9
Redial
Redials the last number called.
See page 8
Battery charging contacts
Place handset face down on the
base to charge the batteries.
1
Base unit aerial
1471
Extend fully for best reception.
See page 7
To set the 1471 call return
feature on or off.
See page 18
OGM
Used when recording and
playing back your own outgoing
message.
Volume
Adjusts the loudspeaker volume.
See page 14
See page 13
Quickdial reference label
VIP
F1050
Automatically alerts you to your
most important callers.
See page 19
Lists the names of up to 10 numbers
stored in the quickdial memory.
See page 10
OGM
Delete
Page
Deletes recorded messages and
memos.
See page 13, 16
Volume
Lets you page the handset.
(Useful in finding a misplaced
handset.)
See page 11
8
LEDs
r
CHARGING – comes on when
the handset battery is being
charged.
Skip
Skip
Skip
Switches message alert On/Off.
Lets you skip forward and
backwards through your messages.
Sets Answer delay.
Answer
on/off
Play
Memo
IN USE – comes on when the
line is in use.
mic
See page 14, 16, 17
BATT LOW – comes on when the
answering machine back-up
battery needs replacing.
Answer On/Off/Stop
Switches the answering machine
on and off, and stops playback of
messages when in Answer
Machine mode.
Play/Memo/Pause
Microphone
Used when playing back
or pausing messages and
when recording memos.
See pages 15, 20
For recording your OGM and
memo messages.
See page 13
Battery charging contacts
In this guide
At a glance
Introduction
Setting up
1
4
5
Using your Freestyle 1050
telephone
8
8
Making and receiving calls
Using the memory to store
and dial numbers
9
Using your Freestyle 1050
answering machine
Outgoing messages
Message display
12
12
12
14
17
Incoming messages
Answer delay
Call screening
17
Using the 1471 feature
Using the VIP feature
Memos
18
19
20
Operating your answering machine
from the cordless handset
21
Remote access
Help
23
27
30
32
34
36
Technical information
Maintenance
Wall mounting
Index
3
Introduction
Your Freestyle 1050 is designed for ease of use and made to the high
standards set by BT
Thank you for making the right choice. You can
expect your Freestyle 1050 to provide many years
of quality service. Please read the instructions
carefully before use and keep this user guide for
future reference.
If your Freestyle 1050 is connected to a PBX
(switchboard), you may have to dial an access
number before 999 to contact the emergency
services.
For your records
Unpacking your Freestyle 1050
Check that your Freestyle 1050 is complete.
When you unpack you should have:
Date of purchase:
Place of purchase:
• Freestyle 1050 handset including
rechargeable battery
Serial number:
(on the underside of the base unit)
Purchase price:
F1050
OGM
•Freestyle 1050 telephone
answering machine
V
olume
For warranty purposes, proof of purchase is
required, so please keep your receipt.
8
r
Skip
Skip
Answer
on/off
Play
Memo
mic
• Mains power lead with
Emergency calls
attached 13 amp adaptor plug
The emergency services can be contacted in the
UK by dialling 999 or 112.
•Wall-mounting bracket,
two screws and wall
plugs for wall mounting
As the Freestyle 1050 is a mains-powered
cordless telephone, in certain situations you may
not be able to make an emergency call:
• If there is severe radio interference.
• If the handset batteries fail.
Customer Helpline
If you have problems with your phone, call the
• If there is a power cut.
Freestyle 1050 Helpline Service on 0845 758 5589
4
Setting up
Follow these steps to get your Freestyle 1050 ready for use
Insert a new PP3 9V alkaline
back-up battery in the base unit
1
3
Handset aerial
✖
The back-up battery is available separately and
ensures your Freestyle 1050 retains messages,
settings and stored phone numbers if there is a
mains power failure. If no battery is installed,
the BATT LOW light comes on when the mains
power is switched on.
Your Freestyle 1050 uses a compact aerial which
does not pull out.
2
Check your telephone socket
In the event of a power failure the back-up
battery will last for up to 6 hours.
If you do not have a modern-style telephone
socket, call Freefone 0800 800 150 and ask for
a BT engineer to come and fit the correct socket.
This is a chargeable service.
5
Plug the mains adaptor cord into
the back of the base unit
Mains power adaptor
The Freestyle 1050 must only be used with the
4
adaptor supplied.
To prevent the cable being pulled out by
accident, route it through the channel on the
underside of the base.
Using any other adaptor will invalidate the approval
given to this apparatus.
Charge the handset battery for at
least 12 hours
6
12V A
PHONE LINE
When you first use your Freestyle 1050, the
rechargeable batteries in the handset need
charging for 12 hours.
Place the handset on the base unit face down,
ensuring the contacts are touching.
The CHARGING light on the base unit comes ON.
After the handset has been charged for 12 hours,
your phone is ready for use.
Electrical storm warning
During periods of electrical storm, you are
advised to disconnect your apparatus because
damage may occur.
As a rule, placing the handset on the base unit
overnight will keep the batteries fully charged
for all normal use.
If a fault occurs during the 12-month warranty
period and it is due to accidental or wilful damage
(including lightning and electrical damage),
BT will not replace or repair free of charge.
The CHARGING light remains on until the
handset is removed from the base unit.
When fully charged and in good condition,
the handset battery will provide up to 6 hours
continuous talk time or 72 hours standby.
Plug the 3 pin adaptor into the
5
mains power socket and switch on
If the handset battery is running low, the
BATTERY LOW light will f lash every 10 -15 seconds.
Your Freestyle 1050 begins the set up procedure.
If you are making a call and the handset
battery is running low, the phone will beep every
10 -15 seconds.
–
–
– the message counter flashes ‘ ’.
–
– the message counter then flashes 0.
– the pre-set outgoing message is ready to use.
Place the handset on the base unit to recharge.
6
To plan the location of the
base unit
Battery Care
9
Batteries cannot be overcharged. However, leaving
the handset on the base unit all the time can
deteriorate rechargeable batteries. To get the longest
possible life from your batteries, take the handset off
the base for a few hours each day.
Your Freestyle 1050 works by sending and
receiving radio signals between the base unit
and the handset.
The strength of the signal depends on where
you site the base unit and how the aerial is
deployed.
Plug your Freestyle 1050 into the
phone socket
7
The higher the base unit is located, the better.
An upstairs room is ideal. The following points
should be considered:
• It should be within easy reach of a mains
socket and a telephone socket. A new-style
telephone socket is needed for this product.
If you do not have one, call us on Freefone
0800 800 150.
• Try to avoid locations near metallic obstructions
or electrical appliances, such as TV sets,
fridges, computers, fluorescent lights, radiators,
metal pipes and metal window frames.
• The Freestyle 1050 can be wall mounted by
using the bracket and screws supplied; see
page 34.
Fully extend the telescopic aerial
on the base unit
8
Your Freestyle 1050 is now ready for use
For the best reception
Try to avoid putting the telescopic aerial near other
electrical appliances, fluorescent lights and large
metallic objects such as cookers, radiators and garage
doors as these may cause interference and reduce the
quality of your calls.
7
Using your Freestyle1050
telephone
Making and receiving calls
To receive a call
The handset range is up to 200 metres from the
base unit in ideal conditions. If you start to go
out of range while using the phone, you will
hear warning beeps. If you do not come back in
range, your call will be cut off.
When the phone rings:
If your handset is on the base unit,
simply pick it up to answer the call.
Or
If your handset is off the base, press the
TALK button to answer the call.
To make a call
Press buttons in order shown
To redial the last number
Lift the handset off the base
Press the TALK button. The handset
IN USE light comes on. The base unit
light flashes. Listen for dial tone.
You can redial a number of up to 32
digits long.
Press the TALK button. You hear the
dialling tone.
Dial the number.
Press the REDIAL button. The last
number you called is redialled.
To end a call
Press the TALK button.
Or
Replace the handset on the base.
8
Using the memory to store
and dial numbers
To ensure the best sound quality
Your Freestyle 1050 automatically
scans available radio channels between
the handset and base for the best quality
signal. However, if you hear noise or
interference during your call:
Your Freestyle 1050 handset can store up to ten
separate phone numbers, each up to 16 digits
long. You can then dial each number by pressing
just two buttons.
To store a number in the memory
Press the CHANNEL button.
Your Freestyle 1050 will select a new
channel for you.
Press buttons in order shown
Press the QUICKDIAL button. You hear
a beep and the IN USE light begins to
flash.
If you go out of range
Your Freestyle 1050 has a range of 200
metres under ideal conditions.
Press one of the 0-9 buttons to set the
location code under which your phone
number will be stored.
However, if you go out of range during
a call, you will hear a series of beeps,
Move closer to the base to re-establish
the signal.
DIAL Dial the number you want to store.
Press the QUICKDIAL button. You hear
a confirmation beep. The number is
stored.
Using the Secrecy button
Repeat these steps for any other
numbers you want to store, using a
different 0-9 location code for each one.
You can prevent your caller from
hearing you while you talk to someone
else close by.
Storing a number in the memory
automatically overwrites any
previous number stored under the
same location code.
Press the SECRECY button. A beep is
heard and the IN USE light flashes.
Your caller cannot hear you until you
press the SECRECY button again.
Stored numbers can include those for
switchboard and network services
that use the and buttons as well as
✱
#
the PAUSE and RECALL functions.
9
To store a number of more than
16 digits
To dial a stored number
Press the TALK button.
Press the QUICKDIAL button.
Press the QUICKDIAL button
Press one of the 0-9 buttons to set the
location code under which your phone
number will be stored.
Press the 0-9 location code under
which the number you want is stored.
The number is dialled automatically.
DIAL Dial the first 16 digits.
Press the QUICKDIAL button. You hear
a confirmation beep. The number is
stored.
Did you know?
You can mix manual and memory dialling as
required. For example, you can dial the area code
0181 380 from the memory and then complete the
number manually.
Press the QUICKDIAL button again.
Press a different 0-9 button to select a
second location code under which to
store the remaining digits.
NOTE
Keep a note of your stored numbers on the Quickdial
DIAL Dial the remaining digits.
reference label on the base unit.
Press the QUICKDIAL button. You hear
a confirmation beep. The rest of the
number is stored.
To dial a stored number of more
than 16 digits
Press the TALK button.
Press the QUICKDIAL button, then the
first 0-9 location code number. The
number begins dialling automatically.
When the first part of the number has
been dialled, press the QUICKDIAL
button again, then the second 0-9
location code number. The rest of the
number is dialled.
10
To page the handset
If you misplace the handset, you can
use PAGE to find it again.
Press the PAGE button on the base.
The handset will beep. The IN USE light
on the base flashes.
Stop the handset beeping either by
pressing the PAGE button again
or
the TALK button on the handset.
To insert a pause
With some switchboards, after dialling
the access code you may have to wait
for a moment while the switchboard
picks up an outside line. If so, press
the PAUSE button to insert a 2.5 second
pause before keying in the telephone
number.
To use the recall button
This button signals Timed Break
Recall only. If you are connected to a
PBX (Private Branch Exchange),
contact your PBX supplier for further
information.
11
Using the Freestyle1050
answering machine
Outgoing messages
Message display
Your Freestyle 1050 can digitally record up to
14 minutes of messages, with each incoming
message lasting a maximum of 2 minutes.
Display
Definition
(Blank)
Power off.
—
—
—
The outgoing message is the message a caller
hears when your Freestyle 1050 answers a call.
Power up or reset.
Power on – answer off mode.
Answer-on mode, 0-30 messages.
Message paused.
—
The Freestyle 1050 has a pre-recorded outgoing
message which announces. ..
0-30
P (flashing)
“Hello, your call cannot be taken at the moment,
so please leave your message after the tone.”
Message recording (memo, outgoing
message or incoming message).
r (flashing)
You can record your own outgoing message to
replace the pre-recorded message.
A (flashing)
Remote access in progress.
Memory full.
F (flashing)
If you record your own message, the pre-recorded
message is automatically removed and stored in
the memory, in case you wish to reinstate it; see
how to delete your outgoing message on page 13.
t or 2 to 9 Setting or reading answer delay.
d (flashing)
E (flashing)
8-0
1471 function in progress.
Error.
Any outgoing message you record can be up to
2 minutes long, but you should keep it short to
allow more time for recording of incoming calls.
Counting down.
NOTE
To record your own outgoing message, speak clearly,
15 to 20cm from the built-in microphone.
12
To record your outgoing message
To delete your outgoing message
You can delete your outgoing message
and return to your Freestyle 1050’s
pre-recorded outgoing message.
Press buttons in order shown
OGM
Press and hold down the OGM button.
Your Freestyle 1050 will beep and r
flashes on the message counter.
OGM
Press the OGM button.
OGM
OGM
“Your message”
Keep holding down the OGM button and
say your message into the microphone.
Your outgoing message is played back
to you.
When you have finished speaking,
release the OGM button.
While the message is playing, press
the DELETE button.
Your Freestyle 1050 will beep, play
back your message, then beep to
confirm the recording. It will then
return to ‘Answer On’ mode.
Your Freestyle 1050 will beep and play
its pre-recorded outgoing message.
“Hello, your call cannot be taken at the
moment, so please leave your message
after the tone.”
To re-record your outgoing message,
repeat this procedure.
Your own message has now been
replaced by the Freestyle 1050’s original
pre-recorded message.
To check your outgoing message
OGM
Press the OGM button.
To switch the answering machine
on/off
Your Freestyle 1050 will beep, play back
your message, then beep to confirm
the recording. It will then return to
‘Answer On’ mode.
Answer
Press the ANSWER ON/OFF button.
Your Freestyle 1050 will announce
“Answer off”.
on/off
“Beep. Your message. Beep”
Display shows a single dash.
Answer
on/off
Press the ANSWER ON/OFF button
again. The machine will announce
“Answer On”.
13
Incoming messages
To adjust the loudspeaker volume
Your Freestyle 1050 will automatically record an
incoming message when it is connected to your
phone socket and is set to ‘Answer On’.
Press buttons in order shown
Your Freestyle 1050 has a volume
range of 0-8 (0 = Off, 8 = Loud).
The pre-set level is 3.
While a message is being recorded, the display
flashes r. It will stop recording if the caller stops
speaking for longer than 6 seconds.
Volume
Press VOL + to increase the volume.
Volume
Two minutes is the maximum time allowed for
each incoming message. If the maximum
message length is reached – or if the memory
becomes full – your Freestyle 1050 will give
4 beeps and hang up.
Press VOL – to decrease the volume.
As you press, a beep sounds at the
level you are selecting. When the
volume is at its highest or lowest, you
will hear two beeps.
NOTE
If a call comes in while you are playing back a
message or memo, the playback continues until
completed, or you take the call.
Message alert
When new messages have been received, your
Freestyle 1050 will beep every 10 seconds. The
volume of the beep is at the volume you have set
for the loudspeaker.
To switch the message alert on or off
When the answering machine is in its
idle state:
Skip
Press and hold the SKIP < button.
The machine announces, “Message alert
off/on” as appropriate.
Skip
Press the SKIP < button again to change
the setting.
14
Using the 1471 feature with your
answering machine
To play back a message
Press the PLAY/MEMO button. Your
Freestyle 1050 announces “You have X
messages”.
Play
When using your answering machine, if
the 1471 feature is switched on, your
Freestyle 1050 will automatically record
the time of each call and the caller’s
number (if available).
Memo
The message will then be played back
followed by the 1471 details(if the
service is switched on) e.g. “Telephone
number XXX called today at 2.13pm”
When the message is played back, you
will then hear these details at the end
of their message.
If you have two or more messages, they
are played back in the order in which
they were received.
If the caller hangs up before recording
their message, your Freestyle 1050
will still record the caller’s number and
time of their call after announcing “you
have no message”. The message counter
will also move up by one. Memos do
not have the time of recording
When all your messages have been
played back, your Freestyle 1050
announces “End of messages”.
The display counts down from 8 to 0.
automatically added.
Press the
STOP/ANSWER ON/OFF button at
any time during playback to stop messages playing.
To pause a message
While listening to the message, press
the PLAY/MEMO. Your Freestyle 1050
will beep every 10 seconds during pause.
Play
Memo
Display shows P.
Play
Press the PLAY/MEMO button again to
Memo
resume playback.
If playback is not resumed within 60 seconds, the
machine automatically resets to ‘Answer On’ mode
15
To skip forward or backward
through messages
NOTE
To cancel deletions and retain your messages,
press the
STOP/ANSWER ON/OFF button during
Press buttons in order shown
the 8 to 0 countdown at the end of your messages.
When playing back messages, you can
skip forward to the next message or
backward to the start of the current or
previous message.
To delete all messages
While the message is being played back.
Following playback of messages, your
Freestyle 1050 will count down from
8 to 0.
Skip
Press the SKIP > button to start playing
the next message. If you press the skip
button while playback is paused, play
will continue with the next message.
You will see the counter change with
each press.
During this time you can delete all
stored messages.
Press the DELETE button while the
display is counting down from 8 to 0.
If you skip beyond the last message,
your Freestyle announces
“End of messages”.
Your Freestyle 1050 will announce...
“All messages deleted”.
Skip
Press the SKIP < button once to replay
the current message.
It will then continue its countdown to
0, and return to ‘Answer On’ mode.
Skip
Press the SKIP < button twice to go to
the start of the previous message.
NOTE
If you accidentally delete all messages you can still
To delete individual messages
save them by pressing the
STOP/ANSWER ON/OFF
button before countdown reaches 0.
Play
Press the PLAY/MEMO button to play
Memo
your messages.
When the message you wish to delete
is playing, press the DELETE button.
Your Freestyle 1050 announces
“Message deleted”.
Skip through your messages to make
any further deletions.
16
Answer delay
To check the answer delay setting
Answer delay sets the number of times your
Freestyle 1050 will ring before answering a call.
Skip
Press the SKIP > button.
Your Freestyle 1050 will announce the
current setting. “Answer delay, 4 rings”.
NOTE
If you set your 1050 Answer Delay to Time Saver
this means that when you call in from another phone
(remote access), if any messages have been recorded
your Freestyle 1050 will answer after only 2 rings.
If there are no messages, it will answer after 6 rings,
thereby allowing you the option of hanging up before
your Freestyle 1050 answers. In using Time Saver,
you can avoid the cost of a call.
Call screening
You can let your Freestyle 1050 answer an
incoming call, allowing you to identify the caller
and decide whether to take the call. (The VIP
feature must be set to OFF).
To use call screening
To set the answer delay
Skip
Make sure that the volume is set to an
audible level. (See page 14).
Press and hold the SKIP > button.
The current setting is displayed on the
message counter and is set to 6 rings
Allow the incoming call to be answered
by your Freestyle 1050 as normal.
You will hear the caller begin to leave
a message.
Skip
Keep holding the SKIP > button.
Your Freestyle 1050 will announce the
answer delay options...
“Time Saver, 2, 3, 4, 5, 6, 7, 8, 9.”
At the base unit
When you hear the setting you want,
Skip
release the SKIP > button. Your
If the handset is resting on the base unit
and you decide to take the call, lift the
handset and speak to the caller.
Freestyle 1050 will then announce the
new answer delay setting and return to
‘Answer On’ mode.“Answer delay, 4 rings”.
Recording will stop automatically.
PLEASE NOTE
If you set the answer delay to a specific number of
rings, it will actually ring one less than the number
you set. So, if you set it to ring 5 times, it will
actually ring 4 times. This is because your
Freestyle requires one ring to activate the radio link
between the base station and the handset ringer.
NOTE
If, when you lift the telephone handset your
Freestyle 1050 does not stop recording, either
replace the handset and lift again, or press the
TALK button to speak to your caller.
17
To screen a call vial the handset
To switch the 1471 feature on and off
When your Freestyle 1050 starts to
record an incoming message, the
handset gives 3 beeps and the IN USE
light flashes.
Press buttons in order shown
When you first switch on your
Freestyle 1050, Call Return is
automatically set to ‘on’.
Press the SECRECY/SCREEN button.
You can hear the caller on the handset.
The 1471 feature can be switched on
and off.
Or
Press the 1471 button to switch it off.
The freestyle 1050 announces
“1471 off”.
To interrupt recording and talk to your
caller, press the TALK button.
Press the 1471 button again to switch
it back on. The Freestyle 1050
announces “1471 on”.
Using the 1471 feature
After each incoming message your Freestyle 1050
is set to dial the free 1471 service and record
the announcement that gives you the telephone
number of your caller whether they leave a
message or not. On playing back messages you
will be given the caller’s number and time of
the call.
NOTE
The free 1471 service announces the day and time
that the call was left. Your Freestyle 1050 will
automatically record this announcement
immediately after receiving a call. Consequently,
the day of the call will be recorded as ‘today’.
Therefore, it is recommended that you check your
messages on a daily basis. The free 1471
NOTE
This service will not work with switchboards and
announcement also asks if you wish to return the
call. In fact, you are not able to do this.
may not work with some Cable Networks.
Please ask your Telecommunication supplier for
further details.
18
To allow VIP callers to signal their
call
Using the VIP feature
Your Freestyle 1050 has a VIP feature which
sets your answering machine to answer calls
silently but allows designated callers to alert you
with a beep that they are trying to contact you.
The VIP feature will only operate with the
answering machine in ‘Answer On’ mode.
Press buttons in order shown
Give your special callers the VIP code.
Your pre-set code is 30. Tell them to
key in the code when they hear your
outgoing message. The VIP alert beeps
last for 30 seconds.
While the VIP feature is switched on, you will
not be disturbed by any other callers and your
answering machine will take messages silently.
If a caller wishes to cancel the alert,
they press the button on their phone.
#
Your Freestyle 1050 will give a long
beep at the end of the outgoing
message and the caller can leave their
message after the beep.
To switch the VIP feature on and off
VIP is pre-set to off.
Press and release the VIP button to turn
it on.
To change the VIP code
By pressing the VIP button, the
Freestyle 1050 announces “VIP on, thirty”.
Press and hold down the VIP button.
The machine announces the current
VIP code e.g. “Thirty”. Continue to hold
down the VIP button and press the
SKIP > button to move forward through
the numbers or press SKIP < to move
Press VIP button again to switch off.
Skip
Skip
To check VIP code and setting
backward.
When the number you want is
announced, release the SKIP and VIP
buttons. The machine announces e.g.
“VIP on/off Twenty five set”.
Press the VIP button.
Your Freestyle 1050 will announce if the
setting is on or off and the code number.
NOTE
The code numbers available run from 00 to 39.
They are announced by your Freestyle 1050.
19
Memos
To cancel any procedure
A personal memo can be recorded on your
Freestyle 1050 and left as a message for another
user. Memos can be of any length, up to the
maximum recording capacity (14 minutes), but
you should keep them short to allow time for
recording incoming messages.
Answer
on/off
Pressing the STOP/ANSWER ON/OFF
button will cancel any procedure currently
in progress and your Freestyle 1050
will return to ‘Answer On’ mode.
When the memory is full
To record a memo
When 14 minutes recording time have
been used up. Or, a maximum of 30
messages have been recorded, your
Freestyle 1050 will not record any more
messages.
Play
Press and hold the PLAY/MEMO button.
Memo
Your Freestyle 1050 will beep and the
display shows r. Speak clearly into the
built-in microphone.
Play
When you have completed your memo,
release the PLAY/MEMO button. Your
Freestyle 1050 will beep again.
Memo
Your memo is now stored and can be
played back later. Memos are stored in
the same way as incoming messages.
NOTE
To play back, delete or skip forward or backward
through memos, follow the instructions for playing
back messages (page 16).
NOTE
If the answer machine is set to ‘off’, recording a
valid memo will switch the answer machine on.
20
Operating your answering
machine from the cordless
handset
To start playback of messages
Press the SECRECY/SCREEN button
on the handset. Your answering machine
will announce either “You have no
messages” and you have 8 seconds to
give it an instruction, or “You have X
messages” and begins playback.
You can use your Freestyle 1050 cordless
handset to listen to your messages, delete, skip
forward or backward and record a memo or new
outgoing message. You can also use it to screen
an incoming call.
Use the handset buttons to operate the
machine as follows:
to stop playback
to pause and resume playback
repeat message (or press twice to play
the previous message)
delete the message that is playing
to skip forward to the next message
(or press twice to skip forward two
messages).
To replay all messages
At the end of your messages, you will
hear “End of messages”.
Within 8 seconds press 2 on your
telephone keypad. All messages are
replayed.
21
To go back to the pre-set outgoing
message
To change your outgoing message
Press the 7 button twice within 8 seconds
Press buttons in order shown
of hearing either “End of messages”
Press the 9 button while your
Freestyle 1050 is waiting for an
instruction.
or
“You have no messages”.
Your outgoing message is played.
Your Freestyle 1050 gives a long beep
after the second press of the 7 button to
tell you it is starting to record.
While the message is playing, press the
5 button. Callers will now hear your
Freestyle 1050 pre-recorded message
“Hello, your call cannot be taken at the
moment, so please leave your message
after the tone.”
When you have finished recording your
new message, press and hold the 0
button for 1 second.
Your Freestyle 1050 will beep and play
your new outgoing message to confirm
recording.
To screen a call via the handset
When your Freestyle 1050 starts to
record an incoming message, the
handset gives 3 beeps and the IN USE
light flashes.
To check your outgoing message
Press the 9 button while your
Freestyle 1050 is waiting for an
instruction.
Press the SECRECY/SCREEN button.
You can hear the caller on the handset.
Your outgoing message is played.
Or
At the end you have 8 seconds in which
to give your machine another instruction.
To interrupt recording and talk to your
caller, press the TALK button.
22
Remote access
Control your answering
To check for messages
machine from another phone
TM
using a TouchTone keypad
Press buttons in order shown
You can turn your Freestyle 1050 answering
machine on and off and listen to your messages
from any TouchToneTM telephone. To protect
your privacy, messages can only be accessed by
entering a 2-digit security code.
Dial your phone number and wait.
When you hear your outgoing message,
press the button on your phone.
✱
You will hear a ‘Beep’.
The code is pre-set and cannot be changed.
The code can be found on the underside of the
base unit.
CODE Key in the first digit of your security
code. You will hear the number you
keyed in and a ‘Beep’.
CODE Key in the second digit of your security
code. You will hear the number you
keyed in then a long ‘Beep’.
Once you have entered your security
code.
If you have no messages you will hear
“You have no messages.”
You now have 8 seconds to enter any
other instructions before your
Freestyle 1050 hangs up.
If you have messages you will hear
“You have X messages.”
Your Freestyle 1050 will then play your
messages.
23
NOTE
To move forward to the next message
If you hear 4 short ‘beeps’, it means that you have
entered the wrong security code and you are invited to
try again.
While a message is playing, press 6 on
your telephone keypad. Your Freestyle
1050 will play the next message.
If you take longer than 8 seconds to enter a or
✱
number, your Freestyle 1050 will hang up.
You can move forward 2 messages by
pressing the 6 button twice and so on.
Controlling your message
To delete the message you are
listening to
You can now play back, delete or skip
backward and forward through your
messages using the telephone keypad,
as follows:
During playback, press the 5 button on
your telephone keypad. Your Freestyle
1050 will announce “Message deleted”.
To replay the message you are
listening to:
To delete all messages
While the message is playing, press 4
on your telephone keypad. The message
will replay from the beginning.
You can delete all messages immediately
after listening to them.
Press the 5 button within 8 seconds of
hearing “End of messages.”
To replay all messages
All messages will be deleted.
Your Freestyle 1050 will announce
“All messages deleted.”
At the end of your messages, you will
hear “End of messages”.
Within 8 seconds press 2 on your
telephone keypad. All messages are
replayed.
NOTE
If you accidentally delete a message or messages,
simply hang up within 8 seconds of hearing the
message “All messages deleted.”
All messages marked for deletion will be restored.
24
NOTE
To pause a message
If the memory is full, you will have to delete some
messages before your Freestyle 1050 will switch to
‘Answer On’ mode.
Press buttons in order shown
After you hear the ‘Memory Full’ announcement, you
have 8 seconds to enter 2 (to listen to your messages),
or 5 to delete all messages).
While the message is playing, press the
2 button.
Press 2 again to resume playback.
If you pause for longer than 60 seconds,
the line will be disconnected.
To turnyourFreestyle1050off
Dial your number and enter your
security code.
To cancel message playback or pause
Press the 8 button within 8 seconds of
hearing either “End of messages”
While listening or pausing, press the
0 button. Your Freestyle 1050 gives 2
beeps and you have 8 seconds to give it
another instruction.
or
“You have no messages”.
Your Freestyle 1050 will announce
“Answer off”.
To turn your Freestyle 1050 on
If you press the 8 button again within
8 seconds, you will turn your
Freestyle 1050 on again and hear the
announcement “Answer On”.
If you have gone out without switching
on your Freestyle 1050, you can turn it
on from another phone.
Ring your answering machine as
normal.
Let your telephone ring 20 times.
Your Freestyle 1050 will then answer.
Hang up the phone. Your Freestyle 1050
is switched on and will answer calls.
25
To go back to the pre-set outgoing
message
To changeyouroutgoingmessage
Press the 7 button twice within 8 seconds
of hearing either “End of messages”.
Press the 9 button while your
Freestyle 1050 is waiting for an
instruction.
or
“You have no messages”.
Your outgoing message is played.
Your Freestyle 1050 gives a long beep
after the second press of the 7 button to
tell you it is starting to record.
While the message is playing, press the
5 button. Callers will now hear your
Freestyle 1050 pre-recorded message
“Hello, your call cannot be taken at the
moment, so please leave your message
after the tone.”
Now record your new OGM.
When you have finished recording
your new message, press and hold the
0 button for at least 1 second.
Your Freestyle 1050 will beep and play
your new outgoing message to confirm
recording.
To checkyouroutgoingmessage
Press the 9 button while your
Freestyle 1050 is waiting for an
instruction.
Your outgoing message is played. At the
end you have 8 seconds in which to
give your machine another instruction.
26
Help
If you have any problems using your Freestyle 1050, this section will
give you the most common, easy-to-follow solutions.
Telephone problems
Possible cause
Solution
• No dialling tone.
Telephone not connected to telephone
line.
Plug the telephone into the
telephone line.
• Telephone will not dial out.
• Telephone cannot receive calls.
Mains disconnected.
Make sure the mains supply is
connected.
Power cut.
Wait until the power is restored.
Handset battery pack is discharged.
Place the handset on the base unit
and recharge it for 12 hours, ensuring
the charging light is on.
• You have dialling tone but the
telephone will not dial out.
You may be trying to use tone
dialling on a pulse dialling exchange.
Check with your network provider.
Your Freestyle 1050 only provides
tone dialling.
You are connected to a PBX and are
not dialling the access code.
Use the PBX access code.
• Handset does not ring.
• No lights on handset.
Handset battery pack is discharged.
Place the handset on the base unit and
recharge it for 12 hours.
• Handset does not ring, but lights
show on base.
Check the REN (see page 31). If you
connect too many telephones or
devices to your line, they may not all
operate correctly.
If the REN exceeds 4, disconnect one
or more telephones or devices.
If your telephone is connected to an
extension socket, it may have been
connected incorrectly.
Check with your telephone engineer
that the extension socket has been
installed correctly.
Check handset battery is not flat.
Recharge handset battery.
27
Telephone problems
Possible cause
Solution
• Callers are faint.
• Interference.
The base unit telescopic aerial is not
extended as high as possible.
Extend the base unit telescopic aerial
as far as possible.
• Buzzing.
You are moving out of range.
Radio channel interference.
Move closer to the base unit.
• Whooshing.
Press the CHANNEL button on the
handset, to select a clearer channel.
• Echoing.
Radio channel interference.
Press the CHANNEL button on the
handset, to select a clearer channel.
• Tinniness.
The base unit or the handset are too
close to electrical equipment or metal
obstructions.
Relocate the base unit or move
around with the handset until
reception improves.
• No Quickdial store.
You may be trying to store the
number with the talk light on.
Ensure that the TALK light is off
before storing the number.
• BATTERY LOW light on the
handset is flashing.
The handset battery needs recharging.
Replace the handset on the base unit,
ensuring that the base unit is plugged
in and that the CHARGING light is on.
• No CHARGING light on the
base unit.
Dirty contacts on base unit or
handset.
Clean the contacts with a dry cloth.
Heavy soiling can be removed with a
pencil eraser.
28
Answering Machine problems
Possible cause
Solution
• General problems.
None of the answering machine
functions will operate while the
telephone is in use.
Ensure that the telephone is not in use
before operating the answering
machine.
• Will not record incoming
messages.
The answering machine is switched
off.
Switch the answering machine on
manually or by remote control.
The answering machine is full.
Delete some or all of your messages
manually or by remote control, to
make room for new messages.
• Distorted outgoing message.
• Faint outgoing message.
• Noisy outgoing message.
The answering machine has a very
sensitive microphone. This picks up
any background noise. If you record
your outgoing message too quietly or
from too far away the sensitivity of the
microphone increases to compensate
and will pick up more background
noise.
Record your outgoing message at a
reasonable volume 20cm away from
the microphone in a quiet
environment.
• No call screening from the
base unit.
The volume is set too low.
Increase the volume to a suitable level
using the volume control.
• Cannot hear messages when
played.
VIP setting is ON.
Switch VIP OFF.
The volume is set too low.
Increase the volume to a suitable level
using the volume control.
• Back-up battery fails frequently.
Frequent power failures will drain the
back-up battery.
Leave the base unit plugged in, or
remove the back-up battery before
unplugging.
Unplugging the base unit from the
power supply drains the back-up
battery.
Switching the mains supply off will
drain the back-up battery.
Remove the back-up battery before
switching the mains supply off.
29
Technical information
Approval for use
Your Freestyle 1050 is tested and approved for
connection to public networks, provided it is
used in accordance with the guidelines in this
user guide.
WARNING
The apparatus is only designed to be operated in
a normal office or domestic environment where
the relative humidity does not exceed 60%. It should
not be used in bathrooms or near water.
You may connect it:
• To direct exchange lines.
• To extensions with new plug and socket
arrangements provided with these direct
exchange lines.
How many phones can you have?
All items of telephone equipment have a Ringer
Equivalence Number (REN), which is used to
calculate the number of items which may be
connected to any one telephone line. Your
Freestyle 1050 has a REN of 1. A total REN of 4
is allowed. If the total REN of 4 is exceeded, the
telephones may not ring. With different telephone
types there is no guarantee of ringing, even when
the REN is less than 4.
• To compatible switchboards.
You may NOT connect it:
• To shared service (party) lines.
• As an extension to a payphone.
This phone is designed for UK use only. Using it
abroad may violate local radio laws.
Connecting to a switchboard
The base unit is intended for use when powered
from the 12V AC mains adaptor supplied, which
conforms to EN60950. Any other usage will
invalidate the approval given to this apparatus if,
as a result, it ceases to comply with EN60950.
Your Freestyle 1050 may be connected to
compatible switchboards. If in doubt, your
switchboard supplier or maintainer should be
able to offer help. Advice on connection to BT
switching systems can be obtained by dialling
BT on 152.
Environment
Your Freestyle 1050 should be kept free of dust,
moisture, high temperature and vibration, and
should not be exposed to direct sunlight. Do not
stand it on carpets or other surfaces which
generate fibres, or place it in locations which
prevent the free flow of air over its surfaces.
If you do not have a compatible switchboard, it
cannot be guaranteed that your Freestyle 1050
will operate correctly under all possible conditions
of connection.
30
Call security
Transmission frequencies of
available channels:
Your Freestyle 1050 has its own digital security
code that prevents other cordless phone owners
from using your phone line. This ensures that
you are charged only for calls using your phone.
However, all approved cordless phones use
radio signals to communicate between the base
unit and cordless handset units. It is therefore
possible that your conversations could be
overheard by other people, on their cordless
phones, or on radios that use the same radio
frequencies.
Channels
Base Unit Tx
Freq./MHz
Handset Tx
Freq./MHz
1
2
3
4
5
6
7
8
31.0375
31.0625
31.0875
31.1125
31.1375
31.1625
31.1875
31.2125
39.9375
39.9625
39.9875
40.0125
40.0375
40.0625
40.0875
40.1125
As this problem applies equally to all similar
cordless phones currently available in the UK,
call privacy cannot be guaranteed. However, the
security coding prevents unauthorised use of
your line.
Safety advice
Don’t use your Freestyle 1050 in the open air
during thunderstorms. Unplug it from the
telephone line and the mains socket when there
are storms in your area.
In the unlikely event of your Freestyle 1050
picking up conversations from other cordless
phones being used nearby, try changing
channels using the CHANNEL button on the
handset.
Don’t use your Freestyle 1050 outdoors in the
rain, or handle it with wet hands.
Don’t install the base unit near a sink, bath or
shower. Electrical appliances can cause serious
injury if used when you are wet or standing in
water.
Transmission frequencies
This cordless telephone has been designed to
operate on radio frequencies which have been
assigned to the exclusive use of cordless
telephones. As the use of cordless telephones
becomes more widespread, the quality of
service obtained from this apparatus may
lessen.
Don’t install the base unit where the various
leads can be tripped over or walked on. This
may cause injury, or damage to the leads and
your Freestyle 1050.
In the event of a power failure
In the event of a mains power failure you will
not be able to make or receive calls from your
Freestyle 1050. Alternative arrangements should
be made for access to emergency services.
31
Maintenance
• Firmly hold the handset in both hands with
the back towards you and the bottom end
away from you.
Installing a handset battery pack and recharging
Replacing the handset on the base unit to
recharge overnight should keep the Freestyle
1050 operative for normal use. In time, the
handset battery pack will no longer hold a
sufficient charge and should be replaced.
• Push the depression in the battery compartment
cover, inward and away from you with both
thumbs, to remove it.
• Undo the plastic belt securing the battery pack.
• Remove the old battery pack by unplugging
the small white plug that connects it to the
handset.
To change the handset battery pack
The handset battery compartment is located at
the back of the handset at the lower end.
• Insert the small white plug of the new battery
pack. (If you look at the shape of the plug and
socket, you will see that it can only be inserted
one way).
• Place the battery pack in the recess, secure it
with the plastic belt and refit the compartment
cover.
• Replace the handset on the base unit and
charge for a full 12 hours.
• The battery pack must be recycled or disposed
of properly.
• Do not burn or puncture as it could release
toxic material which may cause injury.
Spare parts for your Freestyle 1050 are available
from your BT shop or supplier.
32
Care of rechargeable battery pack
Guarantee
If you own your Freestyle 1050 under BT’s
• When you first install the Freestyle 1050, or
replace the battery pack, the handset must be
fully charged for 12 hours before use.
• To maintain optimum charge and battery
condition, the handset should be allowed to
fully discharge about every four months.
• Dispose of Ni-Cad battery packs safely.
Do not puncture or burn them. They contain
toxic materials which could cause injury.
guarantee
BT guarantees the product for one year provided
that:
The goods have only been used for their intended
purpose and have not been subjected to misuse,
or been wilfully or accidentally damaged.
The goods have not been tampered with or
repaired by anyone other than BT, its staff or
agents. If a fault does occur in this product, and
you bought the unit yourself, provided that you
return it to the place of purchase and produce
your receipt, it will either be repaired or replaced
free of charge. The terms and conditions of this
guarantee do not affect your statutory rights.
General cleaning
Clean the cabinet of the handset and the base
with a soft cloth slightly dampened with a mild
solution of water and detergent. Charging
contacts should be cleaned with a dry cloth or
for heavy soiling a pencil eraser can be used.
• Do not clean with a wet cloth.
• Do not clean with abrasive materials or
solvents as these may damage the unit.
• Do not spray aerosol cleaners onto the base
or handset.
If you own your Freestyle 1050 outside the
guarantee period
If your Freestyle 1050 needs repair after the
guarantee period has ended, it must be repaired
so as to remain compliant with the approval
requirements for connection to the telephone
network. We recommend that you call BT on
Freefone 0800 800 150 or visit your nearest
BT shop and you will be informed of our
recommended repair agents.
Extended periods of non-use
It is recommended that you:
• Disconnect the base unit from both mains
supply and telephone line.
• Remove the back-up battery from the base
unit and battery pack from the handset.
• When reconnecting, check that the charging
light on the base unit is on. Recharge the
handset battery for 12 hours.
33
Wall Mounting
1
Your Freestyle 1050 can be wall-mounted by
using the bracket provided.
Drill 2 holes for the screws and insert the
wall-plugs provided (if required).
WALL PLUG
SCREW
You can use the bracket as a template to mark
where the screws should go into the wall.
WALL
102 mm
Please refer to page 35, wall mounting template.
Before you wall-mount your Freestyle 1050,
check that:
2
3
Drive the screws into the wall, leaving about
4mm free on which to mount the bracket and
base unit.
• the wall can support the weight of the base
unit and handset;
• the position you choose leaves enough
space so that the base unit (which is larger
than the bracket) is clear of any obstruction
on the wall, such as a shelf or cupboard.
Room should be left so that the handset can
be placed on charge without touching any
obstructions;
Make sure that the power supply and
the telephone cables are connected
to the base unit, then fit the cables into
the channels on the bottom of the
base unit.
4
5
Clip the bracket onto the base unit as shown
on the next page.
• the position leaves enough space for the
aerial to be extended when wall-mounted.
Attach the bracket and base unit
by hooking them over the screws
protruding from the wall.
For the best operating conditions, try to place
the base unit away from large metal objects and
other electrical appliances.
34
Wall Mounting template
102 mm
2
SQUEEZE
INWARD
1
35
Index
Adaptor
Aerial
6
Ending a call
Guarantee
Help
Helpline
8
33
27
4
base unit
handset
7
5
Incoming messages
Location
Maintenance
Making a call
Memory numbers
dialling
storing
Memory full
Memos
14
7
Answer delay
17
17
17
13
checking
setting
32
8
Answering machine on/off
Answering machine -
operating from the handset
Battery
care of handset battery
changing handset battery
charging handset battery
installation of base unit battery
recommended base unit battery
Calls
10
9, 10
20
21
7, 33
20
32
6
playback
recording
15
20
5
Message alert on/off
Message display
Messages – incoming
delete all messages
delete individual messages
pause
14
5
12
14
ending
making
receiving
8
8
16
16
8
15
Call screening
17
17
18, 22
20
9
playback
15, 21
21
at the base
at the handset
Cancel any procedure
Channel
Charging handset battery
Cleaning
Dialling a memory number
Display - answer machine
Display messages
Emergency calls
replay all messages
skip backwards/forwards
Messages – outgoing
change your message
check your message
deleting
pre-set message
recording
On/off – answering machine
16
12
22
6
13, 22
13
33
10
12
12
4
22
13
13
36
Outgoing messages
Paging
Pause
Power adaptor/cord
Power failure
Power socket
12
11
11
6
on/off
signalling the code
Volume
loudspeaker
Wall-mounting
19
19
14
34
31
6
Wall mounting template
1471 feature
35
Quickdial reference label
Range
10
9
15, 18
Recall
11
8
Redialling last number
REN (Ringer Equivalence Number)
Receiving a call
30
8
Remote access
23
25
26
23
26
24
24
25
26
24
24
25
21
31
9
cancel playback/pause
change your outgoing message
check for messages
check your outgoing message
delete all messages
delete individual messages
pause a message
pre-set message
replay all messages
skip forward
switching on/off remotely
Remote access from the handset
Safety advice
Secrecy
Security
Sound quality
31
9
Stop any procedure
Storing a memory number
Switchboards
Technical information
Telephone socket
Transmission frequencies
VIP feature
20
9, 10
30
30
5, 7
31
19
19
19
checking
changing
37
Offices in Europe, North America,
Japan and Asia Pacific.
The telecommunications services described in this publication
are subject to availability and may be modified from time to time.
Services and equipment are provided subject to British
Telecommunications plc’s respective standard conditions of contract.
Nothing in this publication forms any part of any contract.
CE compliant to 89/336/EEC
(EMC Directive) & 73/23/EEC
(Low Voltage Directive)
© British Telecommunications plc 1999.
Registered Office: 81 Newgate Street, London EC1A 7AJ.
Registered in England No. 1800000.
APPROVED for connection to
telecommunication systems specified
in the instructions for use subject to
the conditions set out in them
Designed by: The Art & Design Partnership Limited.
Printed in China by: Team Concepts
Freestyle 1050 Issue 1 (5/99) 5.
Printed on paper which meets international environmental standards
|