|
GA-K8NE
AMD Socket 754 Processor Motherboard
User's Manual
Rev. 1001
12ME-K8NE-1001
Copyright
© 2005 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved.
The trademarks mentioned in the manual are legally registered to their respective companies.
Notice
The written content provided with this product is the property of Gigabyte.
No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any
means without Gigabyte's prior written permission. Specifications and features are subject to
change without prior notice.
Product Manual Classification
In order to assist in the use of this product, Gigabyte has categorized the user manual in the
following:
„
„
„
For quick installation, please refer to the "Hardware Installation Guide" included with the
product.
For detailed product information and specifications, please carefully read the
"Product User Manual".
For detailed information related to Gigabyte's unique features, please go to "Technology
Guide" section on Gigabyte's website to read or download the information you need.
Table of Contents
GA-K8NE Motherboard Layout ..................................................................................... 6
Block Diagram ............................................................................................................... 7
Chapter 1 Hardware Installation ................................................................................... 9
1-1 Considerations Prior to Installation ................................................................. 9
1-2 Feature Summary .......................................................................................... 10
1-3 Installation of the CPU and Heatsink ............................................................ 12
1-3-1 Installation of the CPU .......................................................................................... 12
1-3-2 Installation of the Heatsink ................................................................................... 13
1-4 Installation of Memory ................................................................................... 14
1-5 Installation of Expansion Cards .................................................................... 15
1-6 I/O Back Panel Introduction .......................................................................... 16
1-7 Connectors Introduction ................................................................................ 17
Chapter 2 BIOS Setup ............................................................................................... 27
The Main Menu (For example: BIOS Ver. : D6) ....................................................... 28
2-1 Standard CMOS Features ............................................................................. 30
2-2 Advanced BIOS Features ............................................................................. 32
2-3 Integrated Peripherals ................................................................................... 34
2-4 Power Management Setup ............................................................................ 37
2-5 PnP/PCI Configurations ................................................................................ 39
2-6 PC Health Status ........................................................................................... 40
2-7 MB Intelligent Tweaker(M.I.T.) ...................................................................... 41
2-8 Load Optimized Defaults ............................................................................... 43
2-9 Set Supervisor/User Password ..................................................................... 43
2-10 Save & Exit Setup ......................................................................................... 44
2-11 Exit Without Saving ....................................................................................... 44
- 4 -
Chapter 3 Drivers Installation ..................................................................................... 45
3-1 Install Chipset Drivers ................................................................................... 45
3-2 Software Application...................................................................................... 46
3-3 Software Information ..................................................................................... 46
3-4 Hardware Information .................................................................................... 47
3-5 Contact Us ..................................................................................................... 47
Chapter 4 Appendix ................................................................................................... 49
4-1 Unique Software Utilities ............................................................................... 49
4-1-1 EasyTune 5 Introduction ....................................................................................... 49
4-1-2 Xpress Recovery Introduction .............................................................................. 50
4-1-3 Flash BIOS Method Introduction .......................................................................... 53
4-1-4 Serial ATA BIOS Setting Utility Introduction ......................................................... 62
4-1-5 2- / 4- / 6- / 8- Channel Audio Function Introduction ........................................... 68
4-1-6 Jack-Sensing and UAJ Introduction ..................................................................... 72
4-2 Troubleshooting............................................................................................. 74
- 5 -
GA-K8NE Motherboard Layout
ATX_12V
MS/KB
SPDIF_I
SPDIF_O
Socket 754
ATX
USB
IDE1
IDE2
AUDIO1
CPU_FAN
AUDIO2
Marvell
FDD
88E1111
F_AUDIO
GA-K8NE
BAT
PCIE_1
CLR_CMOS
BIOS
PCIE_2
nVIDIA®
CODEC
TM
nForce 4 - 4X
PCIE_16
CI
PCI1
CD_IN
F_PANEL
SYS_FAN
PCI2
PCI3
IT8712
COMB
- 6 -
Block Diagram
PCI-ECLK
(100MHz)
CPUCLK+/-(200MHz)
AMD K8
Socket 754
CPU
DDR 400(Note)/333/266/200MHz DIMM
DDR RAM
Hyper Transport Bus
PCI Express x 16
BIOS
RJ45
2 PCI Express x 1
Marvell
4 Serial ATA
88E1111
nVIDIA®
ATA33/66/100/133
IDE Channels
nForce4-4X
PCI-ECLK
(100MHz)
x 1
x 1
Floppy
LPC BUS
PCI Express x 1 Bus
PCI Bus
LPT Port
IT8712
COM Ports
PS/2 KB/Mouse
24MHz
33MHz
CODEC
10 USB
Ports
3PCI
PCICLK
(33MHz)
(Note) Because of CPU limitations, if you want to install DDR400 memory modules in your system, please
install either one double-sided or two single-sided DDR400 memory modules. The DDR400 speed
will drop down to DDR333 if you install two double-sided or three single-sided DDR400 memory
modules.
- 7 -
- 8 -
Chapter 1Hardware Installation
1-1 Considerations Prior to Installation
Preparing Your Computer
The motherboard contains numerous delicate electronic circuits and components which can
become damaged as a result of electrostatic discharge (ESD). Thus, prior to installation, please
follow the instructions below:
1. Please turn off the computer and unplug its power cord.
2. When handling the motherboard, avoid touching any metal leads or connectors.
3. It is best to wear an electrostatic discharge (ESD) cuff when handling electronic components
(CPU, RAM).
4. Prior to installing the electronic components, please have these items on top of an antistatic
pad or within a electrostatic shielding container.
5. Please verify that the power supply is switched off before unplugging the power supply
connector from the motherboard.
Installation Notices
1. Prior to installation, please do not remove the stickers on the motherboard. These stickers
are required for warranty validation.
2. Prior to the installation of the motherboard or any hardware, please first carefully read the
information in the provided manual.
3. Before using the product, please verify that all cables and power connectors are connected.
4. To prevent damage to the motherboard, please do not allow screws to come in contact with
the motherboard circuit or its components.
5. Please make sure there are no leftover screws or metal components placed on the motherboard
or within the computer casing.
6. Please do not place the computer system on an uneven surface.
7. Turning on the computer power during the installation process can lead to damage to system
components as well as physical harm to the user.
8. If you are uncertain about any installation steps or have a problem related to the use of the
product, please consult a certified computer technician.
Instances of Non-Warranty
1. Damage due to natural disaster, accident or human cause.
2. Damage as a result of violating the conditions recommended in the user manual.
3. Damage due to improper installation.
4. Damage due to use of uncertified components.
5. Damage due to use exceeding the permitted parameters.
6. Product determined to be an unofficial Gigabyte product.
- 9 -
Hardware Installation
1-2 Feature Summary
TM
CPU
Š
Š
Š
Š
Š
Š
Š
Š
Š
Š
Š
Socket 754 for AMD Athlon 64 processor (K8)
1600MH/z system bus
Supports core frequencies in excess of 3000+ and faster
nVIDIA® nForce4-4X Chipset
Supported on the Win 2000/XP operating systems
3 DDR DIMM memory slots (supports up to 3GB memory)
Supports DDR 400 (Note 1)/333/266/200 DIMM
1 PCI Express x 16 slot
Chipset
Memory
Slots
2 PCI Express x 1 slots
3 PCI slots
IDE Connections
2 IDE connection (UDMA 33/ATA 66/ATA 100/ATA 133), allows connection of
4 IDE devices
Š
Š
Š
Š
Š
Š
Š
Š
Š
Š
Š
Š
Š
Š
Š
Š
Š
Supported on the Win 2000/XP operating systems
1 FDD connection, allows connection of 2 FDD devices
4 Serial ATA ports from nVIDIA® nForce4-4X controller (SATAII0_1, SATAII2_3)
Supported on the Win 2000/XP operating systems
1 parallel port supporting Normal/EPP/ECP mode
1 serial port (COMA), onboard COMB connection
10 USB 2.0/1.1 ports (rear x 4, front x 6 via cable)
1 front audio connector
1 PS/2 keyboard port
1 PS/2 mouse port
Onboard Marvell 88E1111 chip (10/100/1000 Mbit)
1 RJ 45 port
Supported on the Win 2000/XP operating systems
ALC850 CODEC (UAJ)
FDD Connections
Onboard SATA
Peripherals
Onboard LAN
Onboard Audio
Supports Jack Sensing function
Supports 2 / 4 / 6 / 8 channel audio (Note 2)
Supports Line In ; Line Out (Front Speaker Out) ; MIC ; Surround Speaker Out
(Rear Speaker Out) ; Center/Subwoofer Speaker Out ;
Side Speaker Out connection
Š
Š
Š
Supports SPDIF In/Out connection
CD In
IT8712
I/O Control
(Note 1) Because of CPU limitations, if you want to install DDR400 memory modules in your system, please install either
one double-sided or two single-sided DDR400 memory modules. The DDR400 speed will drop down to DDR333 if
you install two double-sided or three single-sided DDR400 memory modules.
(Note 2) To set up an 8 channel audio configuration, you must use Audio Combo Kit (optional device).
GA-K8NE Motherboard
- 10 -
Hardware Monitor
Š
Š
Š
Š
Š
Š
Š
System voltage detection
CPU temperature detection
CPU / System fan speed detection
CPU warning temperature
CPU fan failure warning
CPU smart fan control
Onboard nForce4-4X chipset (SATAII0_1, SATAII2_3)
Onboard SATA RAID
-
supports data striping (RAID 0) or mirroring (RAID 1) function or
striping + mirroring (RAID 0+1)
-
-
-
supports data transfer rate of up to 150 MB/s
supports hot plugging function
supports a maximum of 4 SATA connections
Š
Š
Š
Š
Š
Š
Š
Supported on the Win 2000/XP operating systems
Use of licensed AWARD BIOS
Supports Q-Flash
Supports @BIOS
Supports EasyTune 5 (Note 3)
BIOS
Additional Features
Overclocking
Form Factor
Over Voltage via BIOS (CPU/ DDR/ HT-Link/ PCIE)
ATX form factor; 30.5cm x 24.4cm
(Note 3) EasyTune 5 functions may vary depending on different motherboards.
- 11 -
Hardware Installation
1-3 Installation of the CPU and Heatsink
Before installing the CPU, please comply with the following conditions:
1. Please make sure that the motherboard supports the CPU.
2. Please take note of the one indented corner of the CPU. If you install the CPU in the wrong
direction, the CPU will not insert properly. If this occurs, please change the insert direction
of the CPU.
3. Please add an even layer of heat sink paste between the CPU and heatsink.
4. Please make sure the heatsink is installed on the CPU prior to system use, otherwise
overheating and permanent damage of the CPU may occur.
5. Please set the CPU host frequency in accordance with the processor specifications. It is not
recommended that the system bus frequency be set beyond hardware specifications since it
does not meet the required standards for the peripherals. If you wish to set the frequency
beyond the proper specifications, please do so according to your hardware specifications
including the CPU, graphics card, memory, hard drive, etc.
1-3-1 Installation of the CPU
Check the processor pins to see that none are bent. Move the socket lever to the unlocked position as shown
in Figure 1.(90o to the plane of the motherboard) prior to inserting the processor. The pin 1 location is
designated on the processor by a copper triangle that matches up to a triangle on the socket as shown in
Figure 2. Align the processor to the socket and gently lower it into place. Do not force the processor into the
socket.
Fig.1
Position lever at a 90 degree angle.
Socket lever
Fig.2
A gold-colored triangle is marked one edge of the CPU. Please align this
edge with the socket edge closest to the CPU lever. Gently place the CPU
into position making sure that the CPU pins fit perfectly into their holes.
Once the CPU is positioned into it socket, place one finger down on the
middle of the CPU and gently press the metal lever back into its original
position.
Please use extra care when installing the CPU. The CPU will not fit if positioned incorrectly.
Rather than applying force, please change the positioning of the CPU.
GA-K8NE Motherboard
- 12 -
1-3-2 Installation of the Heatsink
Fig.1
Before installing the heat sink, please first add an even layer of heat sink
paste on the surface of the CPU. Install all the heat sink components (Please
refer to the heat sink manual for detailed installation instructions).
Fig.2
Please connect the heat sink power connector to the CPU_FAN connector
located on the motherboard so that the heat sink can properly function to
prevent CPU overheating.
The heat sink may adhere to the CPU as a result of hardening of the heat sink paste. To prevent
such an occurrence, it is suggested that either thermal tape rather than heat sink paste be used for
heat dissipation or using extreme care when removing the heat sink.
- 13 -
Hardware Installation
1-4 Installation of Memory
Before installing the memory modules, please comply with the following conditions:
1. Please make sure that the memory used is supported by the motherboard. It is
recommended that memory of similar capacity, specifications and brand be used.
2. Before installing or removing memory modules, please make sure that the computer power
is switched off to prevent hardware damage.
3. Memory modules have a foolproof insertion design. A memory module can be installed in
only one direction. If you are unable to insert the module, please switch the direction.
The motherboard supports DDR memory modules, whereby BIOS will automatically detect memory capacity
and specifications. Memory modules are designed so that they can be inserted only in one direction. The
memory capacity used can differ with each slot.
Notch
DDR
Fig.1
The DIMM socket has a notch, so the DIMM memory module can
only fit in one direction. Insert the DIMM memory module vertically
into the DIMM socket. Then push it down.
Fig.2
Close the plastic clip at both edges of the DIMM sockets to lock the
DIMM module.
Reverse the installation steps when you wish to remove the DIMM
module.
GA-K8NE Motherboard
- 14 -
1-5 Installation of Expansion Cards
You can install your expansion card by following the steps outlined below:
1. Read the related expansion card's instruction document before install the expansion card into the
computer.
2. Remove your computer's chassis cover, screws and slot bracket from the computer.
3. Press the expansion card firmly into expansion slot in motherboard.
4. Be sure the metal contacts on the card are indeed seated in the slot.
5. Replace the screw to secure the slot bracket of the expansion card.
6. Replace your computer's chassis cover.
7. Power on the computer, if necessary, setup BIOS utility of expansion card from BIOS.
8. Install related driver from the operating system.
Installing a PCI Express x 16 expansion card:
Please carefully pull out the small white-
drawable bar at the end of the PCI Express
x 16 slot when you try to install/uninstall the
VGA card. Please align the VGA card to the
onboard PCI Express x 16 slot and press
firmly down on the slot. Make sure your VGA
card is locked by the small white-drawable
bar.
- 15 -
Hardware Installation
1-6 I/O Back Panel Introduction
PS/2 Keyboard and PS/2 Mouse Connector
To install a PS/2 port keyboard and mouse, plug the mouse to the upper port (green) and the keyboard to the
lower port (purple).
Parallel Port
The parallel port allows connection of a printer, scanner and other peripheral devices.
SPDIF_I (SPDIF In)
Use SPDIF In feature only when your device has digital output function.
SPDIF_O (SPDIF Out)
The SPDIF output is capable of providing digital audio to external speakers or compressed AC3
•
data to an external Dolby Digital Decoder.
COM A (Serial Port)
Connects to serial-based mouse or data processing devices.
USB port
Before you connect your device(s) into USB connector(s), please make sure your device(s) such as
USB keyboard, mouse, scanner, zip, speaker...etc. have a standard USB interface. Also make sure
your OS supports USB controller. If your OS does not support USB controller, please contact OS
vendor for possible patch or driver upgrade. For more information please contact your OS or device(s)
vendors.
LAN Port
The provided Internet connection is Gigabit Ethernet, providing data transfer speeds of
10/100/1000Mbps.
Line In
Devices like CD-ROM, walkman etc. can be connected to Line In jack.
Line Out (Front Speaker Out)
Connect the stereo speakers, earphone or front surround speakers to this connector.
MIC In
Microphone can be connected to MIC In jack.
Center/Subwoofer Speaker Out
Connect the Center/Subwoofer speakers to this connector.
Rear Speaker Out
Connect the rear surround speakers to this connector.
GA-K8NE Motherboard
- 16 -
Side Speaker Out
Connect the side surround speakers to this connector.
You can use audio software to configure 2-/4-/6-/8-channel audio functioning.
1-7 Connectors Introduction
1
2
6
5
3
9
15
14
7
13
8
4
10
11
12
1) ATX_12V
9) F_AUDO
10) CD_IN
2) ATX (Power Connector)
3) CPU_FAN
11) F_USB1 / F_USB2/F_USB3
12) COMB
4) SYS_FAN
5) FDD
13) CI
6) IDE1 / IDE2
14) CLR_CMOS
15) BAT
7) SATAII0_1/SATAII2_3
8) F_PANEL
- 17 -
Hardware Installation
1/2) ATX_12V / ATX (Power Connector)
With the use of the power connector, the power supply can supply enough stable power to all the
components on the motherboard. Before connecting the power connector, please make sure that all
components and devices are properly installed. Align the power connector with its proper location on
the motherboard and connect tightly.
The ATX_12V power connector mainly supplies power to the CPU. If the ATX_12V power
connector is not connected, the system will not start.
Caution!
Please use a power supply that is able to handle the system voltage requirements. It is
recommended that a power supply that can withstand high power consumption be used (300W or
greater). If a power supply is used that does not provide the required power, the result can lead to an
unstable system or a system that is unable to start.
If you use a 24-pin ATX power supply, please remove the small cover on the power connector
on the motherboard before plugging in the power cord ; Otherwise, please do not remove it.
Pin No.
Definition
GND
3
1
1
2
3
4
GND
+12V
2
4
+12V
12
24
Pin No.
1
Definition
3.3V
2
3.3V
3
GND
4
+5V
5
GND
6
+5V
7
GND
8
Power Good
9
5V SB(stand by +5V)
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
+12V
+12V
13
1
3.3V(Only for 24pins ATX)
3.3V
-12V
GND
PS_ON(soft On/Off)
GND
GND
GND
-5V
+5V
+5V
+5V
GND
GA-K8NE Motherboard
- 18 -
3/4) CPU_FAN / SYS_FAN (Cooler Fan Power Connector)
The cooler fan power connector supplies a +12V power voltage via a 3-pin power connector and
possesses a foolproof connection design.
Most coolers are designed with color-coded power connector wires. A red power connector wire
indicates a positive connection and requires a +12V power voltage. The black connector wire is the
ground wire (GND).
Please remember to connect the power to the cooler to prevent system overheating and failure.
Caution!
Please remember to connect the power to the CPU fan to prevent CPU overheating and failure.
1
Pin No.
Definition
GND
CPU_FAN
1
2
3
+12V
Sense
1
SYS_FAN
5) FDD (FDD Connector)
The FDD connector is used to connect the FDD cable while the other end of the cable connects to the
FDD drive. The types of FDD drives supported are: 360KB, 720KB, 1.2MB, 1.44MB and 2.88MB.
Please connect the red power connector wire to the pin1 position.
34
33
2
1
- 19 -
Hardware Installation
6) IDE1 / IDE2 (IDE Connector)
An IDE device connects to the computer via an IDE connector. One IDE connector can connect to one
IDE cable, and the single IDE cable can then connect to two IDE devices (hard drive or optical drive). If
you wish to connect two IDE devices, please set the jumper on one IDE device as Master and the other
as Slave (for information on settings, please refer to the instructions located on the IDE device).
40
39
2
1
IDE2
IDE1
7) SATAII0_1 / SATAII2_3 (Serial ATA Connector)
Serial ATA can provide up to150MB/s transfer rate. Please refer to the BIOS setting for the Serial ATA
and install the proper driver in order to work properly.
Pin No.
Definition
GND
TXP
1
2
3
4
5
6
7
1
7
7
TXN
GND
RXN
1
RXP
GND
GA-K8NE Motherboard
- 20 -
8) F_PANEL (Front Panel Jumper)
Please connect the power LED, PC speaker, reset switch and power switch etc of your chassis front
panel to the F_PANEL connector according to the pin assignment below.
19
20
SPEAK-
SPEAK+
Speaker Connector
Power Switch
NC
RES+
RES-
HD-
HD+
PW-
Reset Switch
PW+
MSG-
MSG+
Message LED/
Power/
IDE Hard Disk
Active LED
2
1
Sleep LED
HD (IDE Hard Disk Active LED) (Blue)
SPEAK (Speaker Connector) (Amber)
Pin 1: LED anode(+)
Pin 2: LED cathode(-)
Pin 1: Power
Pin 2- Pin 3: NC
Pin 4: Data(-)
RES (Reset Switch) (Green)
PW (Power Switch) (Red)
Open: Normal
Close: Reset Hardware System
Open: Normal
Close: Power On/Off
Pin 1: LED anode(+)
Pin 2: LED cathode(-)
NC
MSG(Message LED/Power/Sleep LED)
(Yellow)
NC ( Purple)
- 21 -
Hardware Installation
9) F_AUDIO (Front Audio Panel Connector)
If you want to use Front Audio connector, you must remove 5-6, 9-10 Jumper.
In order to utilize the front audio header, your chassis must have front audio connector. Also please
make sure the pin assignments for the cable are the same as the pin assignments for the front audio
header. To find out if the chassis you are buying support front audio connector, please contact your
dealer. Please note, you can have the alternative of using front audio connector or of using rear audio
connector to play sound.
Pin No.
Definition
1
2
3
4
5
6
7
8
9
10
MIC
10
2
9
1
GND
MIC_BIAS
POWER
FrontAudio(R)
Rear Audio (R)/ Return R
NC
No Pin
FrontAudio (L)
Rear Audio (L)/ Return L
10) CD_IN (CD In Connector)
Connect CD-ROM or DVD-ROM audio out to the connector.
Pin No.
Definition
CD-L
1
1
2
3
4
GND
GND
CD-R
GA-K8NE Motherboard
- 22 -
11) F_ USB1 / F_USB2 / F_USB3 (Front USB Connector)
Be careful with the polarity of the front USB connector. Check the pin assignment carefully while you
connect the front USB cable, incorrect connection between the cable and connector will make the
device unable to work or even damage it. For optional front USB cable, please contact your local dealer.
Pin No.
Definition
Power
1
2
3
4
5
6
7
8
9
10
Power
10
2
9
1
USB DX-
USB Dy-
USB DX+
USB Dy+
GND
GND
No Pin
NC
12) COMB (COMB Connector)
Be careful with the polarity of the COMB connector. Check the pin assignments while you connect
the COMB cable. Please contact your nearest dealer for optional COMB cable.
Pin No.
Definition
NDCDB-
NSINB
1
2
3
4
5
6
7
8
9
10
NSOUTB
NDTRB-
GND
2
1
10
9
NDSRB-
NRTSB-
NCTSB-
NRIB-
No Pin
- 23 -
Hardware Installation
13) CI (Chassis Intrusion, Case Open)
This 2-pin connector allows your system to detect if the chassis cover is removed. You can check
the "Case Opened" status in BIOS Setup.
Pin No.
Definition
Signal
GND
1
1
2
14) CLR_CMOS (Clear CMOS)
You may clear the CMOS data to its default values by this jumper. To clear CMOS, temporarily short
1-2 pin. Default doesn't include the "Shunter" to prevent from improper use this jumper.
1
Open: Normal
1
Short: Clear CMOS
GA-K8NE Motherboard
- 24 -
15) BAT (Battery)
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended
by the manufacturer.
Dispose of used batteries according to the manufacturer's
instructions.
If you want to erase CMOS...
1. Turn OFF the computer and unplug the power cord.
2. Take out the battery gently and put it aside for about 10
minutes (Or you can use a metal object to connect the
positive and negative pins in the battery holder to make them
short for one minute).
3. Re-install the battery.
4. Plug the power cord and turn ON the computer.
- 25 -
Hardware Installation
GA-K8NE Motherboard
- 26 -
Chapter 2 BIOS Setup
BIOS (Basic Input and Output System) includes a CMOS SETUP utility which allows user to configure
required settings or to activate certain system features.
The CMOS SETUP saves the configuration in the CMOS SRAM of the motherboard.
When the power is turned off, the battery on the motherboard supplies the necessary power to the CMOS
SRAM.
When the power is turned on, pushing the <Del> button during the BIOS POST (Power-On Self Test) will
take you to the CMOS SETUP screen. You can enter the BIOS setup screen by pressing "Ctrl + F1".
When setting up BIOS for the first time, it is recommended that you save the current BIOS to a disk in the
event that BIOS needs to be reset to its original settings. If you wish to upgrade to a new BIOS, either
GIGABYTE's Q-Flash or @BIOS utility can be used.
Q-Flash allows the user to quickly and easily update or backup BIOS without entering the operating system.
@BIOS is a Windows-based utility that does not require users to boot to DOS before upgrading BIOS but
directly download and update BIOS from the Internet.
CONTROL KEYS
<
> < > < > < > Move to select item
<Enter>
<Esc>
Select Item
Main Menu - Quit and not save changes into CMOS Status Page Setup Menu
and Option Page Setup Menu - Exit current page and return to Main Menu
Increase the numeric value or make changes
Decrease the numeric value or make changes
General help, only for Status Page Setup Menu and Option Page Setup Menu
Item Help
<Page Up>
<Page Down>
<F1>
<F2>
<F5>
<F7>
Restore the previous CMOS value from CMOS, only for Option Page Setup Menu
Load the Optimized Defaults
<F8>
Q-Flash utility
<F9>
System Information
<F10>
Save all the CMOS changes, only for Main Menu
Main Menu
The on-line description of the highlighted setup function is displayed at the bottom of the screen.
Status Page Setup Menu / Option Page Setup Menu
Press <F1> to pop up a small help window that describes the appropriate keys to use and the possible
selections for the highlighted item. To exit the Help Window press <Esc>.
- 27 -
BIOS Setup
The Main Menu (For example: BIOS Ver. : D6)
Once you enter Award BIOS CMOS Setup Utility, the Main Menu (as figure below) will appear on the screen.
Use arrow keys to select among the items and press <Enter> to accept or enter the sub-menu.
CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
`
`
`
`
`
`
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Power Management Setup
PnP/PCI Configurations
PC Health Status
`
MB Intelligent Tweaker(M.I.T.)
Load Optimized Defaults
Set Supervisor Password
Set User Password
Save & Exit Setup
Exit Without Saving
ESC: Quit
KLJI: Select Item
F8: Q-Flash
F10: Save & Exit Setup
Time, Date, Hard Disk Type...
If you can't find the setting you want, please press "Ctrl+F1" to search the advanced option hidden.
„
„
„
„
„
„
„
„
Standard CMOS Features
This setup page includes all the items in standard compatible BIOS.
Advanced BIOS Features
This setup page includes all the items of Award special enhanced features.
Integrated Peripherals
This setup page includes all onboard peripherals.
Power Management Setup
This setup page includes all the items of Green function features.
PnP/PCI Configuration
This setup page includes all the configurations of PCI & PnP ISA resources.
PC Health Status
This setup page is the System auto detect Temperature, voltage, fan, speed.
MB Intelligent Tweaker(M.I.T.)
This setup page is control CPU clock and frequency ratio.
Load Optimized Defaults
Optimized Defaults indicates the value of the system parameters which the system would be in best
performance configuration.
GA-K8NE Motherboard
- 28 -
„
„
„
„
Set Supervisor Password
Change, set, or disable password. It allows you to limit access to the system and Setup, or just to Setup.
Set User Password
Change, set, or disable password. It allows you to limit access to the system.
Save & Exit Setup
Save CMOS value settings to CMOS and exit setup.
Exit Without Saving
Abandon all CMOS value changes and exit setup.
- 29 -
BIOS Setup
2-1 Standard CMOS Features
CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
Standard CMOS Features
Date (mm:dd:yy)
Time (hh:mm:ss)
Tue, Mar 15 2005
14:42:37
Item Help
Menu Level`
`
`
`
`
IDE Channel 0 Master
IDE Channel 0 Slave
IDE Channel 1 Master
IDE Channel 1 Slave
[None]
[None]
[None]
[None]
Change the day, month,
year
<Week>
Sun. to Sat.
Drive A
Drive B
[1.44M, 3.5"]
[None]
<Month>
Floppy 3 Mode Suport
[Disabled]
Jan. to Dec.
Halt On
[All, But Keyboard]
<Day>
1 to 31 (or maximum
allowed in the month)
<Year>
1999 to 2098
KLJI: Move
Enter: Select
+/-/PU/PD: Value
F10: Save
ESC: Exit
F1: General Help
F5: Previous Values
F7: Optimized Defaults
Date
The date format is <week>, <month>, <day>, <year>.
Week
Month
Day
The week, from Sun to Sat, determined by the BIOS and is display only
The month, Jan. Through Dec.
The day, from 1 to 31 (or the maximum allowed in the month)
The year, from 1999 through 2098
Year
Time
The times format in <hour> <minute> <second>. The time is calculated base on the 24-hour military-
time clock. For example, 1 p.m. is 13:00:00.
IDE Channel 0 Master/Slave; IDE Channel 1 Master/Slave
IDE HDD Auto-Detection Press "Enter" to select this option for automatic device detection.
IDE Channel 0 Master/Slave; IDE Channel 1 Master/Slave
IDE devices setup. You can use one of three methods:
• Auto
• None
Allows BIOS to automatically detect IDE devices during POST(default)
Select this if no IDE devices are used and the system will skip the automatic
detection step and allow for faster system start up.
• Manual
User can manually input the correct settings.
Access Mode Use this to set the access mode for the hard drive. The four options are:
CHS/LBA/Large/Auto(default:Auto)
Capacity
Capacity of currently installed hard disk.
GA-K8NE Motherboard
- 30 -
Hard drive information should be labeled on the outside drive casing. Enter the appropriate option
based on this information.
Cylinder
Head
Precomp
Landing Zone
Sector
Number of cylinders
Number of heads
Write precomp
Landing zone
Number of sectors
If a hard disk has not been installed, select NONE and press <Enter>.
Drive A / Drive B
The category identifies the types of floppy disk drive A or drive B that has been installed in the
computer.
None
No floppy drive installed
360K, 5.25"
1.2M, 5.25"
5.25 inch PC-type standard drive; 360K byte capacity.
5.25 inch AT-type high-density drive; 1.2M byte capacity
(3.5 inch when 3 Mode is Enabled).
720K, 3.5"
1.44M, 3.5"
2.88M, 3.5"
3.5 inch double-sided drive; 720K byte capacity
3.5 inch double-sided drive; 1.44M byte capacity. (Default value)
3.5 inch double-sided drive; 2.88M byte capacity.
Floppy 3 Mode Support (for Japan Area)
Disabled
Drive A
Drive B
Both
Normal Floppy Drive. (Default value)
Drive A is 3 mode Floppy Drive.
Drive B is 3 mode Floppy Drive.
Drive A & B are 3 mode Floppy Drives.
Halt on
The category determines whether the computer will stop if an error is detected during power up.
No Errors
The system boot will not stop for any error that may be detected and you
will be prompted.
All Errors
Whenever the BIOS detects a non-fatal error the system will be stopped.
All, But Keyboard The system boot will not stop for a keyboard error; it will stop for all other
errors. (Default value)
All, But Diskette
All, But Disk/Key
The system boot will not stop for a disk error; it will stop for all other errors.
The system boot will not stop for a keyboard or disk error; it will stop for all
other errors.
- 31 -
BIOS Setup
2-2 Advanced BIOS Features
CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
Advanced BIOS Features
`
Hard Disk Boot Priority
First Boot Device
Second Boot Device
Third Boot Device
Boot Up Floopy Seek
Password Check
[Press Enter]
[Floppy]
[Hard Disk]
[CDROM]
[Disabled]
[Setup]
Item Help
Menu Level`
Select Hard Disk Boot
Device Priority
Init Display First
[PEG]
KLJI: Move
Enter: Select
+/-/PU/PD: Value
F10: Save
ESC: Exit
F1: General Help
F5: Previous Values
F7: Optimized Defaults
Hard Disk Boot Priority
Select boot sequence for onboard(or add-on cards) SCSI, RAID, etc.
Use < > or < > to select a device, then press<+> to move it up, or <-> to move it down the list. Press
<ESC> to exit this menu.
First / Second / Third Boot Device
Floppy
LS120
Hard Disk
CDROM
ZIP
Select your boot device priority by Floppy.
Select your boot device priority by LS120.
Select your boot device priority by Hard Disk.
Select your boot device priority by CDROM.
Select your boot device priority by ZIP.
USB-FDD
USB-ZIP
Select your boot device priority by USB-FDD.
Select your boot device priority by USB-ZIP.
USB-CDROM Select your boot device priority by USB-CDROM.
USB-HDD Select your boot device priority by USB-HDD.
Legacy LAN Select your boot device priority by Legacy LAN.
Disabled Disable this function.
Boot Up Floppy Seek
During POST, BIOS will determine the floppy disk drive installed is 40 or 80 tracks. 360K type is 40
tracks 720K, 1.2M and 1.44M are all 80 tracks.
Enabled
Disabled
BIOS searches for floppy disk drive to determine it is 40 or 80 tracks. Note that BIOS
can not tell from 720K, 1.2M or 1.44M drive type as they are all 80 tracks.
BIOS will not search for the type of floppy disk drive by track number. Note that
there will not be any warning message if the drive installed is 360K. (Default value)
GA-K8NE Motherboard
- 32 -
Password Check
System
The system can not boot and can not access to Setup page will be denied if the
correct password is not entered at the prompt.
Setup
The system will boot, but access to Setup will be denied if the correct password is
not entered at the prompt. (Default value)
Init Display First
This feature allows you to select the first initiation of the monitor display from which card when you
install a PCI card and a PCI Express VGA card on the motherboard.
PEG
PCI slot
Set Init display first to PCI Express VGA card. (Default value)
Set Init display first to PCI.
- 33 -
BIOS Setup
2-3 Integrated Peripherals
CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
Integrated Peripherals
On-Chip IDE Channel0
On-Chip IDE Channel1
IDE DMA transfer access
On-Chip MAC Lan
[Enabled]
[Enabled]
[Enabled]
[Auto]
Item Help
Menu Level`
On-Chip LAN BOOT ROM
IDE/SATA RAID function
IDE Primary Master RAID
IDE Primary Slave RAID
IDE Secndry Master RAID
IDE Secndry Slave RAID
Serial-ATA 1
SATA 1 Primary RAID
SATA 1 Secondary RAID
Serial-ATA 2
SATA 2 Primary RAID
SATA 2 Secondary RAID
IDE Prefetch Mode
On-Chip USB
USB Memory Type
[Enabled]
[Enabled]
[Disabled]
[Disabled]
[Disabled]
[Disabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[V1.1+V2.0]
[SHADOW]
KLJI: Move
Enter: Select
+/-/PU/PD: Value
F10: Save
ESC: Exit
F1: General Help
F5: Previous Values
F7: Optimized Defaults
CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
Integrated Peripherals
USB Keyboard Support
USB Mouse Support
AC97 Audio
[Disabled]
[Disabled]
[Auto]
Item Help
Menu Level`
Onboard Serial Port 1
Onboard Serial Port 2
Onboard Parallel Port
Parallel Port Mode
[3F8/IRQ4]
[2F8/IRQ3]
[378/IRQ7]
[SPP]
x
ECP Mode Use DMA
3
KLJI: Move
Enter: Select
+/-/PU/PD: Value
F10: Save
ESC: Exit
F1: General Help
F5: Previous Values
F7: Optimized Defaults
On-Chip IDE Channel0
Enabled
Enable onboard 1st channel IDE port. (Default value)
Disabled
Disable onboard 1st channel IDE port.
On-Chip IDE Channel1
Enabled
Enable onboard 2nd channel IDE port. (Default value)
Disabled
Disable onboard 2nd channel IDE port.
IDE DMA transfer access
Enabled
Enable IDE DMA transfer access. (Default value)
Disabled
Disable this function.
GA-K8NE Motherboard
- 34 -
On-Chip MAC Lan
Auto
Auto-detect onboard LAN chip function. (Default value)
Disabled
Disable onboard LAN chip function.
On-Chip LAN BOOT ROM
This function decide whether to invoke the boot ROM of the onboard LAN chip.
Enabled
Disabled
Enable this function. (Default value)
Disable this function.
IDE/SATA RAID function
Enabled
Enable IDE/SATA RAID function.
Disabled
Disable this function. (Default value)
IDE Primary Master RAID
Enabled
Enable 1st master channel IDE RAID function.
Disabled
Disable this function. (Default value)
IDE Primary Slave RAID
Enabled
Enable 1st slave channel IDE RAID function.
Disabled
Disable this function. (Default value)
IDE Secndry Master RAID
Enabled
Enable 2nd master channel IDE RAID function.
Disabled
Disable this function. (Default value)
IDE Secndry Slave RAID
Enabled
Enable 2nd slave channel IDE RAID function.
Disabled
Disable this function. (Default value)
Serial-ATA 1
Enabled
Disabled
Enable Serial ATA 1 supported. (Default value)
Disable Serial ATA 1 supported.
SATA 1 Primary RAID
Enabled
Enable 1st SATA primary RAID function. (Default value)
Disabled
Disable this function.
SATA 1 Secondary RAID
Enabled
Enable 1st SATA secondary RAID function. (Default value)
Disabled
Disable this function.
Serial-ATA 2
Enabled
Disabled
Enable Serial ATA 2 supported. (Default value)
Disable Serial ATA 2 supported.
SATA 2 Primary RAID
Enabled
Enable 2nd SATA primary RAID function. (Default value)
Disabled
Disable this function.
SATA 2 Secondary RAID
Enabled
Enable 2nd SATA secondary RAID function. (Default value)
Disabled
Disable this function.
- 35 -
BIOS Setup
IDE Prefetch Mode
Enabled
Disabled
Enable IDE Prefetch mode. (Default value)
Disable IDE Prefetch mode.
On-Chip USB
Disabled
V1.1+V2.0
V1.1
Disable this function if you are not using onboard USB function.
Enable USB 1.1 and USB 2.0 controller. (Default value)
Enable only USB 1.1 controller.
USB Memory Type
SHADOW
Set USB memory type to SHADOW. (Default value)
Base Memory(640K)Set USB memory type to base memory(640K).
USB Keyboard Support
Enabled
Enable USB keyboard support.
Disabled
Disable USB keyboard support. (Default value)
USB Mouse Support
Enabled
Enable USB mouse support.
Disabled
Disable USB mouse support. (Default value)
AC97 Audio
Auto
Disabled
Enable onboard AC'97 audio function. (Default value)
Disable this function.
Onboard Serial Port 1
Auto
BIOS will automatically setup the Serial port 1 address.
3F8/IRQ4
2F8/IRQ3
3E8/IRQ4
2E8/IRQ3
Disabled
Enable onboard Serial port 1 and address is 3F8/IRQ4. (Default value)
Enable onboard Serial port 1 and address is 2F8/IRQ3.
Enable onboard Serial port 1 and address is 3E8/IRQ4.
Enable onboard Serial port 1 and address is 2E8/IRQ3.
Disable onboard Serial port 1.
Onboard Serial Port 2
Auto
BIOS will automatically set up the Serial port 2 address.
3F8/IRQ4
2F8/IRQ3
3E8/IRQ4
2E8/IRQ3
Disabled
Enable onboard Serial port 2 and address is 3F8/IRQ4.
Enable onboard Serial port 2 and address is 2F8/IRQ3. (Default value)
Enable onboard Serial port 2 and address is 3E8/IRQ4.
Enable onboard Serial port 2 and address is 2E8/IRQ3.
Disable onboard Serial port 2.
Onboard Parallel Port
Disabled
378/IRQ7
278/IRQ5
3BC/IRQ7
Disable onboard LPT port.
Enable onboard LPT port and address is 378/IRQ7. (Default value)
Enable onboard LPT port and address is 278/IRQ5.
Enable onboard LPT port and address is 3BC/IRQ7.
Parallel Port Mode
SPP
EPP
ECP
ECP+EPP
Using Parallel port as Standard Parallel Port. (Default value)
Using Parallel port as Enhanced Parallel Port.
Using Parallel port as Extended Capabilities Port.
Using Parallel port as ECP and EPP mode.
GA-K8NE Motherboard
- 36 -
ECP Mode Use DMA
3
Set ECP Mode Use DMA to 3. (Default value)
1
Set ECP Mode Use DMA to 1.
2-4 Power Management Setup
CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
Power Management Setup
ACPI Suspend Type
Soft-Off by Power button
PME Event Wake Up
Modem Ring On
USB Resume from Suspend
Power-On by Alarm
Day of Month Alarm
Time (hh:mm:ss) Alarm
Power On By Mouse
Power On By Keyboard
AC BACK Function
[S1(POS)]
[Instant-off]
[Disabled]
[Disabled]
[Disabled]
[Disabled]
Everyday
0 : 0 : 0
Item Help
Menu Level`
x
x
[Disabled]
[Disabled]
[Soft-Off]
KLJI: Move
Enter: Select
+/-/PU/PD: Value
F10: Save
ESC: Exit
F1: General Help
F5: Previous Values
F7: Optimized Defaults
ACPI Suspend Type
S1(POS)
Set ACPI suspend type to S1/POS(Power On Suspend). (Default value)
S3(STR)
Set ACPI suspend type to S3/STR(Suspend To RAM).
Soft-Off by Power button
Instant-off
Press power button then Power off instantly. (Default value)
Delay 4 Sec Press power button 4 seconds to Power off. Enter suspend if button is pressed less
than 4 seconds.
PME Event Wake Up
This feature requires an ATX power supply that provides at least 1A on the 5VSB lead.
Disabled
Enabled
Disable this function. (Default value)
Enable PME as wake up event.
Modem Ring On
An incoming call via modem can awake the system from any suspend state.
Disabled
Enabled
Disable Modem Ring on function. (Default value)
Enable Modem Ring on function.
- 37 -
BIOS Setup
USB Resume from Suspend
Disabled
Disable this function. (Default value)
Enable
Enable USB device wake up system from suspend type.
Power-On by Alarm
You can set "Resume by Alarm" item to enabled and key in Date/Time to power on system.
Disabled
Enabled
Disable this function. (Default value)
Enable alarm function to POWER ON system.
If Power-On by Alarm is Enabled.
Day of Month Alarm :
Everyday, 1~31
Time (hh: mm: ss) Alarm :
(0~23) : (0~59) : (0~59)
Power On By Mouse
Disabled
Disabled this function. (Default value)
Double Click Double click on PS/2 mouse left button to power on the system.
Power On By Keyboard
Disabled
Disabled this function. (Default value)
Any KEY
Press any key to power on the system.
Keyboard 98 If your keyboard have "POWER Key" button, you can press the key to power on the
system.
AC BACK Function
Soft-Off
When AC-power back to the system, the system will be in "Off" state. (Default value)
Full-On
When AC-power back to the system, the system always in "On" state.
GA-K8NE Motherboard
- 38 -
2-5 PnP/PCI Configurations
CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
PnP/PCI Configurations
PCI 1 IRQ Assignment
PCI 2 IRQ Assignment
PCI 3 IRQ Assignment
On-board Device IRQ Assign
[Auto]
[Auto]
[Auto]
[Auto]
Item Help
Menu Level`
KLJI: Move
Enter: Select
+/-/PU/PD: Value
F10: Save
ESC: Exit
F1: General Help
F5: Previous Values
F7: Optimized Defaults
PCI 1 IRQ Assignment
Auto
3,4,5,7,9,10,11,12,14,15
Auto assign IRQ to PCI 1. (Default value)
Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 1.
PCI 2 IRQ Assignment
Auto
3,4,5,7,9,10,11,12,14,15
Auto assign IRQ to PCI 2. (Default value)
Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 2.
PCI 3 IRQ Assignment
Auto
3,4,5,7,9,10,11,12,14,15
Auto assign IRQ to PCI 3. (Default value)
Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 3.
On-board Device IRQ Assign
Auto
3,4,5,7,9,10,11,12,14,15
Auto assign IRQ to onboard device. (Default value)
Set IRQ 3,4,5,7,9,10,11,12,14,15 to onboard device.
- 39 -
BIOS Setup
2-6 PC Health Status
CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
PC Health Status
Vcore
DDR25V
OK
OK
Item Help
Menu Level`
+3.3V
OK
+12V
OK
[Disabled]
Don't monitor
current temperature
Current CPU Temperature
Current CPU FAN Speed
Current SYSTEM FAN Speed
CPU Warning Temperature
CPU FAN Fail Warning
CPU Smart FAN Control
44oC
3183 RPM
0
RPM
[Disabled]
[Disabled]
[Enabled]
[60oC-90oC]
Alarm when current
temperature over than
the selected
temperature
KLJI: Move
Enter: Select
+/-/PU/PD: Value
F10: Save
ESC: Exit
F1: General Help
F5: Previous Values
F7: Optimized Defaults
Current Voltage(V) Vcore / DDR25V / +3.3V / +12V
Detect system's voltage status automatically.
Current CPU Temperature
Detect CPU temperature automatically.
Current CPU/SYSTEM FAN Speed (RPM)
Detect CPU/SYSTEM fan speed status automatically.
CPU Warning Temperature
60oC / 140oF
70oC / 158oF
80oC / 176oF
90oC / 194oF
Disabled
Monitor CPU temperature at 60oC / 140oF.
Monitor CPU temperature at 70oC / 158oF.
Monitor CPU temperature at 80oC / 176oF.
Monitor CPU temperature at 90oC / 194oF.
Disable this function. (Default value)
CPU FAN Fail Warning
Disabled
Disable CPU fan fail warning function. (Default value)
Enabled
Enable CPU fan fail warning function.
CPU Smart FAN Control
Disabled
Disable this function.
Enabled
When this function is enabled, CPU fan will run at different speed depending on
CPU temperature. Users can adjust the fan speed with Easy Tune based on
their requirements. (Default Value)
GA-K8NE Motherboard
- 40 -
2-7 MB Intelligent Tweaker(M.I.T.)
CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
MB Intelligent Tweaker(M.I.T.)
CPU Frequency
CPU Spread Spectrum
PCIE Clock
K8 CPU Clock Ratio
Robust Graphics Booster
CPU Voltage Control
Normal CPU Vcore
Chipset core PCI-E voltage
HT-Link voltage control
DDR voltage control
[200]
Item Help
Menu Level`
[Center Spread]
[100Mhz]
[Default]
[Auto]
[Normal]
1.500V
[Normal]
[Normal]
[Normal]
KLJI: Move
Enter: Select
+/-/PU/PD: Value
F10: Save
ESC: Exit
F1: General Help
F5: Previous Values
F7: Optimized Defaults
Incorrect using these features may cause your system broken. For power end-user use only.
CPU Frequency
200 ~ 456
Set CPU frequency from 200Mhz to 456Mhz.
CPU Spread Spectrum
Disabled
Disable CPU Spread Spectrum.
Center Spread
Set CPU Spread Spectrum to Center Spread. (Default value)
PCIE Clock
100Mhz ~ 150Mhz
Set PCI-E clock from 100Mhz to 150Mhz.
K8 CPU Clock Ratio
Default
Set K8 CPU Clock Ratio to CPU factory default. (Default value)
x4 800Mhz ~ x10 2000Mhz Set K8 CPU Clock Ratio from x4 800Mhz to x10 2000Mhz.
Robust Graphics Booster
Select the options can enhance the VGA graphics card bandwidth to get higher performance.
Auto
Fast
Set Robust Graphics Booster to Auto. (Default value)
Set Robust Graphics Booster to Fast.
Turbo
Set Robust Graphics Booster to Turbo.
CPU Voltage Control
Supports adjustable CPU Vcore from 0.800V to 1.750V. (Default value: Normal)
Normal CPU Vcore
Display your CPU Vcore voltage.
- 41 -
BIOS Setup
Chipset core PCI-E voltage
Normal
+0.1v
+0.2v
+0.3v
Set Chipset core PCI-E voltage as Chipset core PCI-E required. (Default value)
Increase Chipset core PCI-E voltage +0.1V.
Increase Chipset core PCI-E voltage +0.2V.
Increase Chipset core PCI-E voltage +0.3V.
HT-Link voltage control
Normal
+0.1v
+0.2v
+0.3v
Supply HT-Link voltage as HT-Link required. (Default value)
Increase HT-Link voltage +0.1V.
Increase HT-Link voltage +0.2V.
Increase HT-Link voltage +0.2V.
DDR voltage control
Normal
Supply DDR voltage as DDR required. (Default value)
+0.1v
+0.2v
Increase DDR voltage +0.1V.
Increase DDR voltage +0.2V.
GA-K8NE Motherboard
- 42 -
2-8 Load Optimized Defaults
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
`
`
`
`
`
`
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Power Man
PnP/PCI C
PC Health Status
`
MB Intelligent Tweaker(M.I.T.)
Load Optimized Defaults
Set Supervisor Password
Load Optimized Defaults (Y/N)? N
Exit Without Saving
ESC: Quit
KLJI: Select Item
F10: Save & Exit Setup
Load Optimized Defaults
F8: Q-Flash
Selecting this field loads the factory defaults for BIOS and Chipset Features which the system automatically
detects.
2-9 Set Supervisor/User Password
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
`
`
`
`
`
`
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
`
MB Intelligent Tweaker(M.I.T.)
Load Optimized Defaults
Set Supervisor Password
Power Man
Enter Password:
PnP/PCI C
PC Health Status
Exit Without Saving
ESC: Quit
KLJI: Select Item
F8: Q-Flash
F10: Save & Exit Setup
Change/Set/Disable Password
When you select this function, the following message will appear at the center of the screen to assist you in
creating a password.
Type the password, up to eight characters, and press <Enter>. You will be asked to confirm the password.
Type the password again and press <Enter>. You may also press <Esc> to abort the selection and not enter
a password.
To disable password, just press <Enter> when you are prompted to enter password. A message
"PASSWORD DISABLED" will appear to confirm the password being disabled. Once the password is disabled,
the system will boot and you can enter Setup freely.
The BIOS Setup program allows you to specify two separate passwords:
SUPERVISOR PASSWORD and a USER PASSWORD. When disabled, anyone may access all BIOS Setup
program function. When enabled, the Supervisor password is required for entering the BIOS Setup program
and having full configuration fields, the User password is required to access only basic items.
If you select "System" at "Password Check" in Advance BIOS Features Menu, you will be prompted for the
password every time the system is rebooted or any time you try to enter Setup Menu.
If you select "Setup" at "Password Check" in Advance BIOS Features Menu, you will be prompted only when
you try to enter Setup.
- 43 -
BIOS Setup
2-10 Save & Exit Setup
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
`
`
`
`
`
`
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Power Man
PnP/PCI C
PC Health Status
`
MB Intelligent Tweaker(M.I.T.)
Load Optimized Defaults
Set Supervisor Password
Save to CMOS and EXIT (Y/N)? Y
Exit Without Saving
ESC: Quit
KLJI: Select Item
F10: Save & Exit Setup
Save Data to CMOS
F8: Q-Flash
Type "Y" will quit the Setup Utility and save the user setup value to RTC CMOS.
Type "N" will return to Setup Utility.
2-11 Exit Without Saving
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
`
`
`
`
`
`
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Power Man
PnP/PCI C
PC Health Status
`
MB Intelligent Tweaker(M.I.T.)
Load Optimized Defaults
Set Supervisor Password
Quit Without Saving (Y/N)? N
Exit Without Saving
ESC: Quit
KLJI: Select Item
F10: Save & Exit Setup
Abandon all Data
F8: Q-Flash
Type "Y" will quit the Setup Utility without saving to RTC CMOS.
Type "N" will return to Setup Utility.
GA-K8NE Motherboard
- 44 -
Chapter 3Drivers Installation
Pictures below are shown in Windows XP.
Insert the driver CD-title that came with your motherboard into your CD-ROM drive, the driver
CD-title will auto start and show the installation guide. If not, please double click the CD-ROM
device icon in "My computer", and execute the Setup.exe.
3-1 Install Chipset Drivers
After insert the driver CD, "Xpress Install" will scan automatically the system and then list all the drivers that
recommended to install. The "Xpress Install" uses the"Click and Go" technology to install the drivers
automatically. Just select the drivers you want then click the "GO" button. The "Xpress Install" will execute
the installation for you automatically.
Some device drivers will restart your system automatically. After restarting your system the "Xpress
Install" will continue to install other drivers.
System will reboot automatically after install the drivers, afterward you can install others application.
For USB2.0 driver support under Windows XP operating system, please use Windows Service
Pack. After install Windows Service Pack, it will show a question mark "?" in "Universal Serial Bus
controller" under "Device Manager". Please remove the question mark and restart the system
(System will auto-detect the right USB2.0 driver).
- 45 -
Drivers Installation
3-2 Software Application
This page displays all the tools that Gigabyte developed and some free software, you can choose anyone
you want and press "install" to install them.
3-3 Software Information
This page lists the contents of software and drivers in this CD-title.
GA-K8NE Motherboard
- 46 -
3-4 Hardware Information
This page lists all device you have for this motherboard.
3-5 Contact Us
Please see the last page for details.
- 47 -
Drivers Installation
GA-K8NE Motherboard
- 48 -
Chapter 4 Appendix
4-1 Unique Software Utilities
4-1-1 EasyTune 5 Introduction
EasyTune 5 presents the most convenient Windows based system performance enhancement and
manageability utility. Featuring several powerful yet easy to use tools such as 1) Overclocking for enhancing
system performance, 2) C.I.A. and M.I.B. for special enhancement for CPU and Memory, 3) Smart-Fan
control for managing fan speed control of both CPU cooling fan and North-Bridge Chipset cooling fan, 4) PC
health for monitoring system status.(Note)
User Interface Overview
Button / Display
Overclocking
C.I.A./C.I.A.2 and M.I.B./M.I.B.2
Smart-Fan
PC Health
GO
"Easy Mode" & "Advance Mode"
Display screen
Function display LEDs
GIGABYTE Logo
Description
1.
2.
3.
4.
5.
6.
7.
8.
9.
Enters the Overclocking setting page
Enters the C.I.A./2 and M.I.B./2 setting page
Enters the Smart-Fan setting page
Enters the PC Health setting page
Confirmation and Execution button
Toggles between Easy and Advance Mode
Display panel of CPU frequency
Shows the current functions status
Log on to GIGABYTE website
TM
10. Help button
11. Exit or Minimize button
Display EasyTune 5 Help file
TM
Quit or Minimize EasyTune 5 software
(Note) EasyTune 5 functions may vary depending on different motherboards.
- 49 -
Appendix
4-1-2 Xpress Recovery Introduction
What is Xpress Recovery ?
Xpress Recovery is a utility used to back up and restore an OS partition.
If the hard drive is not working properly, the user can restore the drive to
its original state.
1. Supports FAT16, FAT32, and NTFS formats
2. Must be connected to the IDE1 Master
3. Allows installation of only one OS
4. Must be used with an IDE hard disk supporting HPA
5. The first partition must be set as the boot partition. When the boot partition is backed up,
please do not alter its size.
6. Xpress Recovery is recommended when using Ghost to return boot manager to NTFS
format.
How to use the Xpress Recovery
1. Boot from CD-ROM (BMP Mode)
Enter the BIOS menu, select "Advanced BIOS Feature" and set to boot from CD-ROM. Insert the
provided driver CD into your CD drive, then save and exit the BIOS menu. Once the computer has
restarted, the phrase "Boot from CD:" will appear at the bottom left-hand corner of the screen. When
"Boot from CD:" appears, press any key to enter Xpress Recovery.
Once you have completed this step, subsequent access to Xpress Recovery can also function by
pressing the F9 key during computer power on.
.
.
Verifying DMI Pool Data
Boot from CD:
Boot from CD:
Xpress Recovery V1.0 (C) Copy Right 2003. GIGABYTE Technology CO. , Ltd.
1. Execute Backup Utility
2. Execute Restore Utility
3. Remove Backup Image
4. Set Password
5. Exit and Restart
Build 2011
GA-K8NE Motherboard
- 50 -
2. Press F9 during powering on the computer. (Text Mode)
Award Modular BIOS v6.00PG, An Energy Star Ally
Copyright (C) 1984-2004, Award Software, Inc.
Intel 865PE AGPSet BIOS for 8IPE1000MT F1
Check System Health OK
.
.
.
F9 For Xpress Recovery
Press DEL to enter SETUP / Q-Flash, F9 For Xpress Recovery
08/16/2002-I845GE-6A69YG01C-00
Xpress Recovery V1.0 (C) Copy Right 2003. GIGABYTE Technology CO. , Ltd.
1. Execute Backup Utility
2. Execute Restore Utility
3. Remove Backup Image
4. Set Password
5. Exit and Restart
1. If you have already entered Xpress Recovery by booting from the CD-ROM, you can
enter Xpress Recovery in the future by pressing the F9 key.
2. System storage capacity as well as drive reading/writing speed will affect backup speed.
3. It is recommended that Xpress Recovery be immediately installed after OS and all
required driver and software installations are complete.
- 51 -
Appendix
1. Execute Backup Utility:
ꢀ Press B to Backup your System or Esc to Exit
The backup utility will automatically scan your system and back up data as a backup image in your hard
drive.
Not all systems support access to Xpress Recovery by pressing the F9 key during computer
power on. If this is the case, please use the boot from CD-ROM method to enter Xpress
Recovery.
2. Execute Restore Utility:
ꢀ This program will recover your system to factory default.
Press R to restore your system back to factory default or press Esc to exit
Restores backup image to original state.
3. Remove Backup Image:
ꢀ Remove backup image. Are you sure? (Y/N)
Remove the backup image.
4. Set Password:
ꢀ Please input a 4-16 character long password (a-z or 0-9) or press Esc to exit
You can set a password to enter Xpress Recovery to protect your hard disk data. Once this is done,
password input will be required to enter Xpress Recovery during the next as well as subsequent system
restarts. If you wish to remove the need for password entry, please select "Set Password" and under
"New Password/Confirm Password", make sure there is no entry and then press "Enter" to remove
password requirement.
5. Exit and Restart:
Exit and restart your computer.
GA-K8NE Motherboard
- 52 -
4-1-3 Flash BIOS Method Introduction
Method 1 : Q-FlashTM Utility
Q-FlashTM is a BIOS flash utility embedded in Flash ROM. With this utility,
users only have to stay in the BIOS menu when they want to update
BIOS. Q-Flash?allows users to flash BIOS without any utility in DOS or
Windows. Using Q-FlashTM indicating no more fooling around with any complicated instructions and
operating system since it is in the BIOS menu.
Please note that because updating BIOS has potential risk, please do it with caution!! We are
sorry that Gigabyte Technology Co., Ltd is not responsible for damages of system because of
incorrect manipulation of updating BIOS to avoid any claims from end-users.
Before You Begin:
Before you start updating BIOS with the Q-FlashTM utility, please follow the steps below first.
1. Download the latest BIOS for your motherboard from Gigabyte's website.
2. Extract the BIOS file downloaded and save the BIOS file (the one with model name.Fxx. For
example, 8KNXPU.Fba) to a floppy disk.
3. Reboot your PC and press Del to enter BIOS menu.
The BIOS upgrading guides below are separated into two parts.
If your motherboard has dual-BIOS, please refer to Part One.
If your motherboard has single-BIOS, please refer to Part Two.
Part One:
Updating BIOS with Q-FlashTM Utility on Dual BIOS Motherboards.
Some of Gigabyte motherboards are equipped with dual BIOS. In the BIOS menu of the motherboards
supporting Q-Flash and Dual BIOS, the Q-Flash utility and Dual BIOS utility are combined in the same
screen. This section only deals with how to use Q-Flash utility.
In the following sections, we take GA-8KNXP Ultra as the example to guide you how to flash BIOS
from an older version to the latest version. For example, from Fa3 to Fba.
Award Modular BIOS v6.00PG, An Energy Star Ally
Copyright (C) 1984-2003, Award Software, Inc.
Intel i875P AGPset BIOS for 8KNXP Ultra Fa3
Check System Health OK , VCore = 1.5250
Main Processor : Intel Pentium(R) 4 1.6GHz (133x12)
<CPUID : 0F27 Patch ID : 0027>
The BIOS file is Fa3
before updating
Memory Testing : 131072K OK
Memory Frequency 266 MHz in Single Channel
Primary Master : FUJITSU MPE3170AT ED-03-08
Primary Slave : None
Secondary Master : CREATIVEDVD-RM DVD1242E BC101
Secondary Slave : None
Press DEL to enter SETUP / Dual BIOS / Q-Flash / F9 For
Xpress Recovery
08/07/2003-i875P-6A79BG03C-00
- 53 -
Appendix
Entering the Q-FlashTM utility:
Step1: To use Q-Flash utility, you must press Del in the boot screen to enter BIOS menu.
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Select Language
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Power Management Setup
PnP/PCI Configurations
PC Health Status
Save & Exit Setup
MB Intelligent Tweaker(M.I.T.)
Exit Without Saving
ESC: Quit
F3: Change Language
F10: Save & Exit Setup
F8: Dual BIOS/Q-Flash
Time, Date, Hard Disk Type...
Step 2: Press F8 button on your keyboard and then Y button to enter the Dual BIOS/Q-Flash utility.
Exploring the Q-FlashTM / Dual BIOS utility screen
The Q-Flash / Dual BIOS utility screen consists of the following key components.
Dual BIOS Utility
Boot From......................................... Main Bios
Dual BIOS utility bar
Main ROM Type/Size.............................SST 49LF003A
Backup ROM Type/Size.........................SST 49LF003A
512K
512K
Task menu for
Dual BIOS
utility
Wide Range Protection Disable
Boot From Main Bios
Auto Recovery Enable
Halt On Error Disable
Copy Main ROM Data to Backup
Load Default Settings
Save Settings to CMOS
Q-FlashTM utility title
bar
Q-Flash Utility
Load Main BIOS from Floppy
Load Backup BIOS from Floppy
Save Main BIOS to Floppy
Save Backup BIOS to Floppy
Task menu for
Q-FlashTM utility
Enter : Run
ꢁꢂ:Move
ESC:Reset
F10:Power Off
Action bar
Task menu for Dual BIOS utility:
Contains the names of eight tasks and two item showing information about the BIOS ROM type. Blocking a
task and pressing Enter key on your keyboard to enable execution of the task.
Task menu for Q-Flash utility:
Contains the names of four tasks. Blocking a task and pressing Enter key on your keyboard to enable execu-
tion of the task.
Action bar:
Contains the names of four actions needed to operate the Q-Flash/Dual BIOS utility. Pressing the buttons
mentioned on your keyboards to perform these actions.
GA-K8NE Motherboard
- 54 -
Using the Q-FlashTM utility:
This section tells you how to update BIOS using the Q-Flash utility. As described in the "Before you begin"
section above, you must prepare a floppy disk having the BIOS file for your motherboard and insert it to your
computer. If you have already put the floppy disk into your system and have entered the Q-Flash utility,
please follow the steps below to flash BIOS.
Steps:
1. Press arrow buttons on your keyboard to move the light bar to "Load Main BIOS from Floppy" item in
the Q-Flash menu and press Enter button.
Later, you will see a box pop up showing the BIOS files you previously downloaded to the floppy disk.
If you want to save the current BIOS for backup purpose, you can begin Step 1 with "Save Main
BIOS to Floppy" item.
2. Move to the BIOS file you want to flash and press Enter.
In this example, we only download one BIOS file to the floppy disk so only one BIOS file,
8KNXPU.Fba, is listed.
Please confirm again you have the correct BIOS file for your motherboard.
Dual BIOS Utility
Boot From.........................................
Main Bios
Main ROM Type/Size.............................SST 49LF003A
Backup ROM Type/Size.........................SST 49LF003A
512K
512K
Wide Range Protection Disable
1 file(s) found
Boo
8KNXPU.Fba
512K
BIOS file in the floppy
disk.
Total size : 1.39M
Free size : 911.50K
DEL : Delete
F5 : Refresh
Save Settings to CMOS
Q-Flash Utility
Load Main BIOS from Floppy
Load Backup BIOS from Floppy
Save Main BIOS to Floppy
Save Backup BIOS to Floppy
Enter : Run
ꢁꢂ:Move
ESC:Reset
F10:Power Off
After pressing Enter, you'll then see the progress of reading the BIOS file from the floppy disk.
Dual BIOS Utility
Boot From.........................................
Main Bios
Main ROM Type/Size.............................SST 49LF003A
Backup ROM Type/Size.........................SST 49LF003A
512K
512K
Wide Range Protection Disable
Reading BIOS file from floppy ...
Don't Turn Off Power or Reset System
Do not turn off power or
reset your system at this
stage!!
>>>>>>>>>>>>>>.....................
Save Settings to CMOS
Q-Flash Utility
Load Main BIOS from Floppy
Load Backup BIOS from Floppy
Save Main BIOS to Floppy
Save Backup BIOS to Floppy
Enter : Run
ꢁꢂ:Move
ESC:Reset
F10:Power Off
After BIOS file is read, you'll see a confirmation dialog box asking you "Are you sure to update BIOS?"
- 55 - Appendix
3. Press Y button on your keyboard after you are sure to update BIOS.
Then it will begin to update BIOS. The progress of updating BIOS will be displayed.
Please do not take out the floppy disk when it begins flashing BIOS.
4. Press any keys to return to the Q-Flash menu when the BIOS updating procedure is completed.
Dual BIOS Utility
Boot From.........................................
Main Bios
Main ROM Type/Size.............................SST 49LF003A
Backup ROM Type/Size.........................SST 49LF003A
512K
512K
Wide Range Protection Disable
You can repeat Step 1 to
4 to flash the backup
BIOS, too.
!! Copy BIOS completed - Pass !!
Please press any key to continue
Save Settings to CMOS
Q-Flash Utility
Load Main BIOS from Floppy
Load Backup BIOS from Floppy
Save Main BIOS to Floppy
Save Backup BIOS to Floppy
Enter : Run
ꢁꢂ:Move
ESC:Reset
F10:Power Off
5. Press Esc and then Y button to exit the Q-Flash utility. The computer will restart automatically after
you exit Q-Flash.
Dual BIOS Utility
Boot From.........................................
Main Bios
Main ROM Type/Size.............................SST 49LF003A
Backup ROM Type/Size.........................SST 49LF003A
512K
512K
Wide Range Protection Disable
Are you sure to RESET ?
[Enter] to continure or [Esc] to abort...
Save Settings to CMOS
Q-Flash Utility
Load Main BIOS from Floppy
Load Backup BIOS from Floppy
Save Main BIOS to Floppy
Save Backup BIOS to Floppy
Enter : Run
ꢁꢂ:Move
ESC:Reset
F10:Power Off
After system reboots, you may find the BIOS version on your boot screen becomes the one you flashed.
Award Modular BIOS v6.00PG, An Energy Star Ally
Copyright (C) 1984-2003, Award Software, Inc.
Intel i875P AGPset BIOS for 8KNXP Ultra Fba
The BIOS file
Check System Health OK , VCore = 1.5250
Main Processor : Intel Pentium(R) 4 1.6GHz (133x12)
<CPUID : 0F27 Patch ID : 0027>
becomes Fab after
Memory Testing : 131072K OK
updating.
Memory Frequency 266 MHz in Single Channel
Primary Master : FUJITSU MPE3170AT ED-03-08
Primary Slave : None
Secondary Master : CREATIVEDVD-RM DVD1242E BC101
Secondary Slave : None
Press DEL to enter SETUP / Dual BIOS / Q-Flash / F9 For
Xpress Recovery
09/23/2003-i875P-6A79BG03C-00
GA-K8NE Motherboard
- 56 -
6. Press Del to enter BIOS menu after system reboots. When you are in BIOS menu, move to
Load Fail-Safe Defaults item and press Enter to load BIOS Fail-Safe Defaults. Normally the system
redetects all devices after BIOS has been upgraded. Therefore, we highly recommend reloading the
BIOS defaults after BIOS has been upgraded.
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Select Language
Load Fail-Safe Defaults
Load Optimized Defaults
Power Manag
PnP/PCI Coni
PC Health Status
Load Fail-Safe Defaults (Y/N)? Y
Save & Exit Setup
Exit Without Saving
MB Intelligent Tweaker(M.I.T.)
ESC: Quit
F3: Change Language
F10: Save & Exit Setup
F8: Dual BIOS/Q-Flash
Time, Date, Hard Disk Type...
Press Y on your keyboard to load defaults.
7. Select Save & Exit Setup item to save the settings to CMOS and exit the BIOS menu.
System will reboot after you exit the BIOS menu. The procedure is completed.
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Select Language
Load Fail-Safe Defaults
Load Optimized Defaults
Power Manag
PnP/PCI Con
PC Health Status
Save to CMOS and EXIT (Y/N)? Y
Save & Exit Setup
Exit Without Saving
MB Intelligent Tweaker(M.I.T.)
ESC: Quit
F3: Change Language
F10: Save & Exit Setup
F8: Dual BIOS/Q-Flash
Time, Date, Hard Disk Type...
Press Y on your keyboard to save and exit.
Part Two:
Updating BIOS with Q-FlashTM Utility on Single-BIOS Motherboards.
This part guides users of single-BIOS motherboards how to update BIOS using the Q-FlashTM utility.
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Top Performance
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Power Management Setup
PnP/PCI Configurations
PC Health Status
Save & Exit Setup
MB Intelligent Tweaker(M.I.T.)
Exit Without Saving
ESC: Quit
F3: Change Language
F10: Save & Exit Setup
F8: Q-Flash
Time, Date, Hard Disk Type...
- 57 -
Appendix
Exploring the Q-FlashTM utility screen
The Q-FlashBIOS utility screen consists of the following key components.
Q-FlashTM utility bar
Q-Flash Utility V1.30
Flash Type/Size.................................SST 49LF003A
256K
Keep DMI Data Enable
Task menu for
Q-FlashTM utility
Update BIOS from Floppy
Save BIOS to Floppy
Enter : Run
ꢁꢂ:Move
ESC:Reset
F10:Power Off
Action bar
Task menu for Q-Flash utility:
Contains the names of three tasks. Blocking a task and pressing Enter key on your keyboard to enable
execution of the task.
Action bar:
Contains the names of four actions needed to operate the Q-Flash utility. Pressing the buttons mentioned on
your keyboards to perform these actions.
Using the Q-FlashTM utility:
This section tells you how to update BIOS using the Q-Flash utility. As described in the "Before you begin"
section above, you must prepare a floppy disk having the BIOS file for your motherboard and insert it to your
computer. If you have already put the floppy disk into your system and have entered the Q-Flash utility,
please follow the steps below to flash BIOS.
Steps:
1. Press arrow buttons on your keyboard to move the light bar to "Update BIOS from Floppy" item in the
Q-Flash menu and press Enter button.
Later, you will see a box pop up showing the BIOS files you previously downloaded to the floppy disk.
If you want to save the current BIOS for backup purpose, you can begin Step 1 with "Save BIOS
to Floppy" item.
2. Move to the BIOS file you want to flash and press Enter.
In this example, we only download one BIOS file to the floppy disk so only one BIOS file,
8GE800.F4, is listed.
Please confirm again you have the correct BIOS file for your motherboard.
Q-Flash Utility V1.30
Flash Type/Size.................................SST 49LF003A
256K
1 file(s) found
8GE800.F4
256K
BIOS file in the floppy
disk.
Total size : 1.39M
En
Free size : 1.14M
DEL : Delete
er Off
F5 : Refresh
Q-Flash Utility V1.30
Flash Type/Size.................................SST 49LF003A
256K
Do not turn off power or
reset your system at
this stage!!
Reading BIOS file from floppy ...
>>>>>>>>>>>>>>.....................
En
er Off
Don't Turn Off Power or Reset System
After BIOS file is read, you'll see a confirmation dialog box asking you "Are you sure to update BIOS?"
Please do not take out the floppy disk when it begins flashing BIOS.
GA-K8NE Motherboard
- 58 -
3. Press Y button on your keyboard after you are sure to update BIOS.
Then it will begin to update BIOS. The progress of updating BIOS will be shown at the same time.
Q-Flash Utility V1.30
Flash Type/Size.................................SST 49LF003A
256K
Updating BIOS Now
Do not turn off power or
reset your system
at this stage!!
>>>>>>>>>>>>>>>>>>>.........................
En
er Off
Don't Turn Off Power or Reset System
4. Press any keys to return to the Q-Flash menu when the BIOS updating procedure is completed.
Q-Flash Utility V1.30
Flash Type/Size.................................SST 49LF003A
256K
!! Copy BIOS completed - Pass !!
Please press any key to continue
En
er Off
5. Press Esc and then Y button to exit the Q-Flash utility. The computer will restart automatically after
you exit Q-Flash.
Q-Flash Utility V1.30
Flash Type/Size.................................SST 49LF003A
256K
Are you sure to RESET ?
[Enter] to continure or [Esc] to abort...
En
er Off
After system reboots, you may find the BIOS version on your boot screen becomes the one you flashed.
Award Modular BIOS v6.00PG, An Energy Star Ally
Copyright (C) 1984-2003, Award Software, Inc.
Intel 845GE AGPSet BIOS for 8GE800 F4
The BIOS file
Check System Health OK
Main Processor : Intel Pentium(R) 4 1.7GHz (100x17.0)
<CPUID : 0F0A Patch ID : 0009>
Memory Testing : 122880K OK + 8192K Shared Memory
becomes F4 after
updating
Primary Master : FUJITSU MPE3170AT ED-03-08
Primary Slave : None
Secondary Master : CREATIVEDVD-RM DVD1242E BC101
Secondary Slave : None
Press DEL to enter SETUP / Q-Flash
03/18/2003-I845GE-6A69YG01C-00
6. Press Del to enter BIOS menu after system reboots and "Load BIOS Fail-Safe Defaults". See how
to Load BIOS Fail-Safe Defaults, please kindly refer to Step 6 to 7 in Part One.
Congratulation!! You have updated BIOS successfully!!
- 59 -
Appendix
Method 2 : @BIOSTM Utility
If you do not have a DOS startup disk, we recommend that you use the
new @BIOS utility. @BIOS allows users to update their BIOS under
Windows. Just select the desired @BIOS server to download the latest
version of BIOS.
Fig 1. Installing the @BIOS utility
Fig 2. Installation Complete and Run @BIOS
Click Sart/ Programs/ GIGABYTE/@BIOS
Select @BIOS item
Fig 3. The @BIOS Utility
Fig 4. Select the desired @BIOS server
Click "ꢀ"
Click "Update New BIOS"
1. Methods and steps:
I. Update BIOS through Internet
a. Click "Internet Update" icon
b. Click "Update New BIOS" icon
c. Select @BIOSTM sever
d. Select the exact model name on your motherboard
e. System will automatically download and update the BIOS.
II. Update BIOS NOT through Internet:
a. Do not click "Internet Update" icon
b. Click "Update New BIOS"
c. Please select "All Files" in dialog box while opening the old file.
d. Please search for BIOS unzip file, downloading from internet or any other methods (such as:
K8NE.D6).
e. Complete update process following the instruction.
GA-K8NE Motherboard
- 60 -
III. Save BIOS
In the very beginning, there is "Save Current BIOS" icon shown in dialog box. It means to save the
current BIOS version.
IV. Check out supported motherboard and Flash ROM:
In the very beginning, there is "About this program" icon shown in dialog box. It can help you check out
which kind of motherboard and which brand of Flash ROM are supported.
2. Note:
I. In method I, if it shows two or more motherboard's model names to be selected, please make
sure your motherboard's model name again. Selecting wrong model name will cause the
system unbooted.
II. In method II, be sure that motherboard's model name in BIOS unzip file are the same as your
motherboard's. Otherwise, your system won't boot.
III. In method I, if the BIOS file you need cannot be found in @BIOSTM server, please go onto
Gigabyte's web site for downloading and updating it according to method II.
IV. Please note that any interruption during updating will cause system unbooted
- 61 -
Appendix
4-1-4 Serial ATA BIOS Setting Utility Introduction
RAID Levels
RAID (Redundant Array of Independent Disks) is a method of combining two hard disk drives into one logical
unit. The advantage of an Array is to provide better performance or data fault tolerance. Fault tolerance is
achieved through data redundant operation, where if one drives fails, a mirrored copy of the data can be
found on another drive. This can prevent data loss if the operating system fails or hangs. The individual disk
drives in an array are called members. The configuration information of each member is recorded in the
reserved sector that identifies the drive as a member. All disk members in a formed disk array are recognized
as a single physical drive to the operating system.
Hard disk drives can be combined together through a few different methods. The different methods are
referred to as different RAID levels. Different RAID levels represent different performance levels, security
levels and implementation costs. The RAID levels which the nVIDIA® nForce4 chipset supports are RAID 0,
RAID 1, RAID 0+RAID 1 and JBOD.
RAID 0 (Striping)
RAID 0 reads and writes sectors of data interleaved between multiple drives. If any disk member fails, it
affects the entire array. The disk array data capacity is equal to the number of drive members times the
capacity of the smallest member. The striping block size can be set from 4KB to 64KB. RAID 0 does not
support fault tolerance.
RAID 1 (Mirroring)
RAID 1 writes duplicate data onto a pair of drives and reads both sets of data in parallel. If one of the
mirrored drives suffers a mechanical failure or does not respond, the remaining drive will continue to function.
Due to redundancy, the drive capacity of the array is the capacity of the smallest drive. Under a RAID 1
setup, an extra drive called the spare drive can be attached. Such a drive will be activated to replace a failed
drive that is part of a mirrored array. Due to the fault tolerance, if any RAID 1 drive fails, data access will not
be affected as long as there are other working drives in the array.
RAID 0+1 (Striping + Mirroring)
RAID 0+1 combines the performance of data striping (RAID 0) and the fault tolerance of disk mirroring (RAID
1). Data is striped across multiple drives and duplicated on another set of drives.
JBOD (Spanning)
A spanning disk array is equal to the sum of the all drives when the drives used are having different capacities.
Spanning stores data onto a drive until it is full, then proceeds to store files onto the next drive in the array.
When any disk member fails, the failure affects the entire array. JBOD is not really a RAID and does not
support fault tolerance.
GA-K8NE Motherboard
- 62 -
Please follow the steps below to construct a complete RAID array:
1) Have ready your hard drives for RAID construction.
Note: To achieve best performance, it is recommended that the hard drives used are of similar make
and storage capacity.
2) Please attach the hard drive connectors to their appropriate location on the motherboard ie. IDE, SCSI,
or SATA.
3) Enter the motherboard BIOS and locate RAID setup (Please refer to the section on Integrated Peripherals).
4) Enter RAID setup in the BIOS and select the RAID type (For instance, enter F10 to select NVIDIA RAID;
Ctrl + S to select Silicon Image).
5) Complete driver installation.
6) Complete RAID utility installation.
More information on steps 4 and 5 is provided. (For more detailed setup information, please visit our website
Configuring the NVIDIA RAID BIOS
The NVRAID BIOS setup lets you choose the RAID array type and which hard drives you want to make part
of the array.
Entering the RAID BIOS Setup
1. After rebooting your computer, wait until you see the RAID software prompting you to press F10. The
RAID prompt appears as part of the system POST and boot process prior to loading the OS. You have a few
seconds to press F10 before the window disappears.
NVIDIA RAID IDE ROM BIOS 4.81
Copyright (C) 2004 NVIDIA Corp.
Detecting array ...
Press F10 to enter RAID setup utility ...
Press F10.
The NVIDIA RAID Utility - Define a New Array window appears (as Figure below).
NVIDIA RAID Utility Jan 12 2005
- Define a New Array -
RAID Mode: Mirroring
Free Disks
Striping Block: Optimal
Array Disks
Loc
Disk Model Name
Loc
Disk Model Name
1.0.M
1.1.M
Maxtor 6Y080M0
Maxtor 6Y080M0
[ꢃ] Add
[ꢄ] Del
[ESC] Quit
[F6] Back
[F7] Finish
[TAB] Navigate
[ꢁꢂ] Select
[ENTER] Popup
- 63 -
Appendix
Using the "Define a New Array" Window
If necessary, press the tab key to move from field to field until the appropriate field is highlighted.
Selecting the RAID Mode
By default, this is set to Mirroring. To change to a different RAID mode, press the down arrow key until the
mode that you want appears in the RAID Mode box - either Mirroring, Striping, Spanning, or Stripe Mirroring.
Selecting the Striping Block Size
Striping block size is given in kilobytes, and affects how data is arranged on the disk. It is recommended to
leave this value at the default Optimal, which is 64KB, but the values can be between 4 KB and 128 KB.
Assigning the Disks
The disks that you enabled from the RAID Config BIOS setup page appear in the Free Disks block. These
are the drives that are available for use as RAID array disks. To designate a free disk to be used as a RAID
array disk,
1. Tab to the Free Disks section. The first disk in the list is selected.
2. Move it from the Free Disks block to the Array Disks block by pressing the rightarrow key (ꢃ). The first disk
in the list is moved, and the next disk in the list is selected and ready to be moved.
3. Continue pressing the right-arrow key (ꢃ) until all the disks that you want to use as RAID array disks
appear in the Array Disks block.
NVIDIA RAID Utility Jan 12 2005
- Define a New Array -
RAID Mode: Mirroring
Free Disks
Striping Block: Optimal
Array Disks
Loc
Disk Model Name
Loc
Disk Model Name
1.0.M
1.1.M
Maxtor 6Y080M0
Maxtor 6Y080M0
[ꢃ] Add
[ꢄ] Del
[ESC] Quit
[F6] Back
[F7] Finish
[TAB] Navigate
[ꢁꢂ] Select
[ENTER] Popup
GA-K8NE Motherboard
- 64 -
Completing the RAID BIOS Setup
After assigning your RAID array disks, press F7. The Clear disk data prompt appears.
NVIDIA RAID Utility Jan 12 2005
- Define a New Array -
RAID Mode: Mirroring
Free Disks
Striping Block: Optimal
Clear disk data?
Disk Model Name
Loc
Disk Model Name
Maxtor 6Y080M0
Maxtor 6Y080M0
[Y] YES [N] NO
[ꢄ] Del
[ESC] Quit
[F6] Back
[F7] Finish
[TAB] Navigate
[ꢁꢂ] Select
[ENTER] Popup
Press Y if you want to wipe out all the data from the RAID array, otherwise press N. You must choose Yes if
the drives were previously used as RAID drives. The Array List window appears, where you can review the
RAID arrays that you have set up.
You can select a disk array as boot device if you want to boot operating system from an array. Use the arrow
keys to select the array, then press B to specify the array as bootable.
NVIDIA RAID Utility Jan 12 2005
- Array List -
Boot
Yes
Id
2
Status
Vendor
Array Model Name
MIRROR 76.33G
Healthy
NVIDIA
[Ctrl-X] Exit
[ꢁꢂ] Select
[B] Set Boot
[N] New Array
[ENTER] Detail
- 65 -
Appendix
Press Enter to view and verify details. The Array Detail screen appears.
The Array Detail screen shows various information about the array that you selected, such as Striping Block
used, RAID Mode, Striping Width, Disk Model Name, and disk capacity.
Array 2 : NVIDIA MIRROR 76.33G
- Array Detail -
RAID Mode: Mirroring
Striping Width : 1
Striping Block: 64K
Adapt
Channel
M/S
Index
Disk Model Name
Capacity
1
1
1
0
Master
Master
0
1
Maxtor 6Y080M0
Maxtor 6Y080M0
76.33GB
76.33GB
[R] Rebuild
[D] Delete
[C] Clear Disk
[ENTER] Return
If you want to mark this disk as empty and wipe out all its contents, press C.
At the prompt, press Y to wipe out all the data, otherwise press N.
Press Enter again to go back to the previous screen and then press Ctrl + X to exit the RAID setup.
Now that the RAID setup has been configured from the RAID BIOS, the next step is to configure and load
drivers under Windows.
GA-K8NE Motherboard
- 66 -
Installing the RAID drivers
To install operating system onto a serial ATA hard disk successfully, you need to install the SATA controller
driver during OS installation. Without the driver, the hard disk may not be recognized during the Windows
setup process. First of all, copy the driver for the SATA controller from the motherboard driver CD-ROM to a
floppy disk. See the instructions below about how to copy the driver in MS-DOS mode(Note1). Prepare a startup
disk that has CD-ROM support and a blank formatted floppy disk.
Step 1: Insert the prepared startup disk and motherboard driver CD-ROM in your system. Boot from the
startup disk. Once at the A:\> prompt, change to the CD-ROM drive (example: D:\>). At the D:\> prompt, type
the following two commands. Press ENTER after each command (Fig.1):
cd bootdrv
menu
Step 2: When the controller menu (Fig.2) appears, remove the startup disk and insert the blank formatted
disk. Select the controller driver by pressing the corresponding letter from the menu. Your system will then
automatically zip and transfer this driver file to the floppy disk. Press 0 to exit when finished.
Fig.1
Fig. 2
Step 3: After completing the steps, boot from the Windows installation disk to install the RAID drivers.
Press F6 as soon as you see the "Press F6 if you need to install a third party SCSI or RAID driver" message,
then supply serial ATA controller driver by this floppy disk. Follow the on-screen instructions to complete the
installation.
(Each time you add a new hard drive to a RAID array, the RAID driver will have to be installed under
Windows once for that hard drive. After that, the driver will not have to be installed.)
(Note 1): For users without a startup disk.
Use an alternative system and insert the GIGABYTE motherboard drive CD-ROM. From the CD-
ROM drive (example: D:\) double click the MENU.exe file in the BootDrv folder. A command prompt
window will open similar to that in Fig. 2.
- 67 -
Appendix
4-1-5 2- / 4- / 6- / 8-ChannelAudio Function Introduction
This motherboard provide 6 audio connector. You are able to use 2-/
4-/6-/8-channnels audio feature by audio software selection.
Introduction of audio connectors:
You may connect CD-ROM/DVD-ROM, walkman or
others audio input to Line In.
The front channels or earphone can be connected to
Line Out (Front Speaker Out).
Connect microphone to Mic In.
Connect the rear channels to Rear Speaker Out.
Connect the Center/Subwoofer channels to Center/
Subwoofer Speaker Out.
Line In
Rear Speaker Out
Line Out
(Front Speaker Out)
Center/Subwoofer
Speaker Out
Side Speaker
Out
Mic In
Connect the side channels to Side Speaker Out.
Following pictures are in Windows XP.
Stereo Speakers Connection and Settings:
We recommend that you use the speaker with amplifier to acquire the best sound effect if the stereo output
is applied.
STEP 1:
Connect the stereo speakers or earphone to "Line
Out".
Line Out
STEP 2 :
Following installation of the audio driver, you find a
Sound Effect
icon on the lower right hand taskbar.
Click the icon to select the function.
To set up an 8 channel audio configuration, you must use Audio Combo Kit (optional device).
GA-K8NE Motherboard
- 68 -
STEP 3:
Click "Speaker Configuration" then click on the
left selection bar and select "2CH Speaker" to
complete 2 channel audio configuration.
4 Channel Audio Setup
STEP 1 :
Connect the front channels to "Front Speaker Out",
the rear channels to "Rear Speaker Out".
Front Speaker Out
Rear Speaker Out
STEP 2 :
Following installation of the audio driver, you find a
Sound Effect
icon on the lower right hand taskbar.
Click the icon to select the function.
STEP 3:
Click "Speaker Configuration" then click on the
left selection bar and select "4CH Speaker" to
complete 4 channel audio configuration.
- 69 -
Appendix
6 Channel Audio Setup
STEP 1 :
Connect the front channels to "Front Speaker Out",
the rear channels to "Rear Speaker Out", and the
Center/Subwoofer channels to "Center/Subwoofer
Speaker Out".
Front Speaker Out
Rear Speaker Out
Center/Subwoofer
Speaker Out
STEP 2 :
Following installation of the audio driver, you find a
Sound Effect
icon on the lower right hand taskbar.
Click the icon to select the function.
STEP 3:
Click "Speaker Configuration" then click on the
left selection bar and select "6CH Speaker" to
complete 6 channel audio configuration.
GA-K8NE Motherboard
- 70 -
8 Channel Audio Setup
STEP 1 :
Connect the front channels to "Front Speaker Out",
the rear channels to "Rear Speaker Out", the Center/
Subwoofer channels to "Center/Subwoofer Speaker
Out", and the side channels to "Side Speaker Out".
Front Speaker Out
Rear Speaker Out
Center/Subwoofer
Speaker Out
Side Speaker Out
STEP 2 :
Following installation of the audio driver, you find a
Sound Effect
icon on the lower right hand taskbar.
Click the icon to select the function.
STEP 3:
Click "Speaker Configuration" then click on the
left selection bar and select "6CH Speaker" to
complete 6 channel audio configuration.
Sound Effect Configuration:
At the sound effect menu, users can adjust sound
option settings as desired.
- 71 -
Appendix
4-1-6 Jack-Sensing and UAJ Introduction
Jack-Sensing provides audio connectors error-detection function.
Install Microsoft DirectX8.1 or later version before to enable Jack-Sensing support for
Windows 98/98SE/2000/ME.
Jack-Sensing includes 2 parts: AUTO and MANUAL. Following is an example for 2 channels (Windows XP):
Introduction of audio connectors
You may connect CDROM, Walkman or others audio
input devices to Line In jack, speakers, earphone or
others output devices to Line Out jack, and micro-
phone to MIC In jack.
Auto-detecting:
Please connect the devices to the right jacks as
above. A window will appear as right
picture if you setup the devices properly.
Please note that 3D audio function will only
appear when 3D audio inputs.
GA-K8NE Motherboard
- 72 -
If you set wrong with the connectors, the warning
message will come out as right picture.
Manual setting:
If the device picture shows different from what you
set, please press "Manual Selection" to set.
UAJ Introduction
UAJ (Universal Audio Jack) has a very smart feature: It will switch signal automatically when user plugs his
audio device to the wrong jack (Line-in/ Line-out). That means users do not need to worry the audio device
should be plug in Line-in or Line-out jack, the device will work perfectly after UAJ is activated.
Enable UAJ function:
You can click "UAJ Automatic" button to enable UAJ
function.
- 73 -
Appendix
4-2 Troubleshooting
Below is a collection of general asked questions. To check general asked questions based on a specific
Question 1: I cannot see some options that were included in previous BIOS after updating BIOS. Why?
Answer: Some advanced options are hidden in new BIOS version. Please press Ctrl and F1 keys after
entering BIOS menu and you will be able to see these options.
Questions 2: Why is the light of my keyboard/optical mouse still on after computer shuts down?
Answer: In some boards, a small amount of electricity is kept on standby after computer shuts down and
that's why the light is still on.
Question 3: How do I clear CMOS?
Answer: If your board has a Clear CMOS jumper, please refer to the Clear CMOS steps in the manual. If your
board doesn't have such jumper, you can take off the on-board battery to leak voltage to clear CMOS.
Please refer to the steps below:
Steps:
1. Turn off power.
2. Disconnect the power cord from MB.
3. Take out the battery gently and put it aside for about 10 minutes (Or you can use a metal object to
connect the positive and negative pins in the battery holder to makethem short for one minute).
4. Re-insert the battery to the battery holder.
5. Connect power cord to MB again and turn on power.
6. Press Del to enter BIOS and load Fail-Safe Defaults(or load Optimized Defaults).
7. Save changes and reboot the system.
Question 4: Why do I still get a weak sound after turning up the speaker to the maximum volume?
Answer: Please make sure the speaker you are using is equipped with an internal amplifier. If not, please
change another speaker with power/amplifier and try again later.
Question 5: Sometimes I hear different continuous beeps from computer after system boots up. What do
these beeps usually stand for?
Answer: The beep codes below may help you identify the possible computer problems. However, they are
only for reference purposes. The situations might differ from case to case.
ꢃ
AWARD BIOS Beep Codes
1 short: System boots successfully
2 short: CMOS setting error
1 long 1 short: DRAM or M/B error
1 long 2 short: Monitor or display card error
1 long 3 short: Keyboard error
1 long 9 short: BIOS ROM error
Continuous long beeps: DRAM error
Continuous short beeps: Power error
ꢃAMI BIOS Beep Codes
Computer gives 1 short beep when system boots successfully.
*Except for beep code 8, these codes are always fatal.
1 beep Refresh failure
*
2 beeps Parity error
3 beeps Base 64K memory failure
4 beeps Timer not operational
5 beeps Processor error
6 beeps 8042 - gate A20 failure
7 beeps Processor exception interrupt error
8 beeps Display memory read/write failure
9 beeps ROM checksum error
10 beeps CMOS shutdown register read/write error
11 beeps Cache memory bad
GA-K8NE Motherboard
- 74 -
- 75 -
Appendix
GA-K8NE Motherboard
- 76 -
- 77 -
Appendix
GA-K8NE Motherboard
- 78 -
Contact Us
ꢁ
Taiwan (Headquarters)
ꢁ
Japan
GIGA-BYTE TECHNOLOGY CO., LTD.
Address: No.6, Bau Chiang Road, Hsin-Tien, Taipei 231,
Taiwan
NIPPON GIGA-BYTE CORPORATION
ꢁ
Singapore
TEL: +886-2-8912-4888
GIGA-BYTE SINGAPORE PTE. LTD.
Tech. Support :
FAX: +886-2-8912-4003
Tech. Support :
Non-Tech. Support(Sales/Marketing) :
Non-Tech. Support(Sales/Marketing) :
ꢁ
U.K.
G.B.T. TECH. CO., LTD.
ꢁ
U.S.A.
TEL: +44-1908-362700
G.B.T. INC.
FAX: +44-1908-362709
TEL: +1-626-854-9338
Tech. Support :
FAX: +1-626-854-9339
Non-Tech. Support(Sales/Marketing) :
Tech. Support :
Non-Tech. Support(Sales/Marketing) :
ꢁ
The Netherlands
GIGA-BYTE TECHNOLOGY B.V.
TEL: +31-40-290-2088
ꢁ
Germany
G.B.T. TECHNOLOGY TRADING GMBH
TEL: +49-40-2533040 (Sales)
NLTech.Support: 0900-GIGABYTE (0900-44422983)
BE Tech.Support: 0900-84034
+49-1803-428468 (Tech.)
FAX: +31-40-290-2089
FAX: +49-40-25492343 (Sales)
+49-1803-428329 (Tech.)
Tech. Support :
Non-Tech. Support(Sales/Marketing) :
Tech. Support :
Non-Tech. Support(Sales/Marketing) :
- 79 -
Appendix
ꢁ
China
ꢁ
Russia
NINGBO G.B.T. TECH. TRADING CO., LTD.
Tech. Support :
Moscow Representative Office Of GIGA-BYTE Technology
Co., Ltd.
Non-Tech. Support(Sales/Marketing) :
Shanghai
Tech. Support :
Non-Tech. Support(Sales/Marketing) :
TEL: +86-021-63410999
FAX: +86-021-63410100
Beijing
ꢁ
Poland
Office of GIGA-BYTE TECHNOLOGY Co., Ltd. in POLAND
Tech. Support :
TEL: +86-10-62102838
FAX: +86-10-62102848
Wuhan
Non-Tech. Support(Sales/Marketing) :
TEL: +86-27-87851061
FAX: +86-27-87851330
GuangZhou
ꢁ
Serbia & Montenegro
Representative Office Of GIGA-BYTE Technology Co., Ltd. in
SERBIA & MONTENEGRO
TEL: +86-20-87586074
FAX: +86-20-85517843
Chengdu
Tech. Support :
Non-Tech. Support(Sales/Marketing) :
TEL: +86-28-85236930
FAX: +86-28-85256822
Xian
TEL: +86-29-85531943
FAX: +86-29-85539821
Shenyang
ꢁ
Czech Republic
Representative Office Of GIGA-BYTE Technology Co., Ltd. in
CZECH REPUBLIC
TEL: +86-24-23960918
FAX: +86-24-23960918-809
Tech. Support :
Non-Tech. Support(Sales/Marketing) :
ꢁ
Australia
GIGABYTE TECHNOLOGY PTY. LTD.
Tech. Support :
Non-Tech. Support(Sales/Marketing) :
ꢁ
Romania
Representative Office Of GIGA-BYTE Technology Co., Ltd. in
Romania
Tech. Support :
ꢁ
France
Non-Tech. Support(Sales/Marketing) :
GIGABYTE TECHNOLOGY FRANCE S.A.R.L.
Tech. Support :
Non-Tech. Support(Sales/Marketing) :
GA-K8NE Motherboard
- 80 -
|
Glem Gas_Emilia C64ECT User Manual
Fagor America SHA 730 X User Manual
Electrolux 922042 User Manual
Diamond Multimedia ATI Radeon HD 4850 User Manual
Daewoo GB14H3 User Manual
Cypress CY7C1422BV18 User Manual
Clarity D613C User Manual
Asus SABERTOOTH X79 P9X79EWS User Manual
Asus JUMPERFREE PC133 User Manual
AG Neovo Neovo TS 17R User Manual