P8H61 R2.0 Series
• P8H61 R2.0
• P8H61 PLUS R2.0
• P8H61/USB3 R2.0
Contents
iii
Contents
iv
Contents
v
Safety information
Electrical safety
•
To prevent electric shock hazard, disconnect the power cable from the electric outlet
before relocating the system.
•
When adding or removing devices to or from the system, ensure that the power cables
for the devices are unplugged before the signal cables are connected. If possible,
disconnect all power cables from the existing system before you add a device.
•
•
•
Before connecting or removing signal cables from the motherboard, ensure that all
power cables are unplugged.
Seek professional assistance before using an adapter or extension cord. These devices
could interrupt the grounding circuit.
Ensure that your power supply is set to the correct voltage in your area. If you are not
sure about the voltage of the electrical outlet you are using, contact your local power
company.
•
If the power supply is broken, do not try to fix it by yourself. Contact a qualified service
technician or your retailer.
Operation safety
•
•
•
•
Before installing the motherboard and adding devices on it, carefully read all the manuals
that came with the package.
Before using the product, ensure that all cables are correctly connected and the power
cables are not damaged. If you detect any damage, contact your dealer immediately.
To avoid short circuits, keep paper clips, screws, and staples away from connectors,
slots, sockets and circuitry.
Avoid dust, humidity, and temperature extremes. Do not place the product in any area
where it may become wet.
•
•
Place the product on a stable surface.
If you encounter technical problems with the product, contact a qualified service
technician or your retailer.
About this guide
This user guide contains the information you need when installing and configuring the
motherboard.
How this guide is organized
This guide contains the following parts:
•
Chapter 1: Product introduction
This chapter describes the features of the motherboard and the new technology it
supports.
•
Chapter 2: BIOS information
This chapter tells how to change system settings through the BIOS Setup menus.
Detailed descriptions of the BIOS parameters are also provided.
vi
Conventions used in this guide
To ensure that you perform certain tasks properly, take note of the following symbols used
throughout this manual.
DANGER/WARNING: Information to prevent injury to yourself when trying to
complete a task.
CAUTION: Information to prevent damage to the components when trying to
complete a task.
IMPORTANT: Instructions that you MUST follow to complete a task.
NOTE: Tips and additional information to help you complete a task.
Where to find more information
Refer to the following sources for additional information and for product and software
updates.
1.
ASUS websites
The ASUS website provides updated information on ASUS hardware and software
products. Refer to the ASUS contact information.
2.
Optional documentation
Your product package may include optional documentation, such as warranty flyers,
that may have been added by your dealer. These documents are not part of the
standard package.
Typography
Bold text
Italics
Indicates a menu or an item to select.
Used to emphasize a word or a phrase.
<Key>
Keys enclosed in the less-than and greater-than sign means
that you must press the enclosed key.
Example: <Enter> means that you must press the Enter or
Return key.
<Key1>+<Key2>+<Key3>
If you must press two or more keys simultaneously, the key
names are linked with a plus sign (+).
Example: <Ctrl>+<Alt>+<D>
vii
P8H61 R2.0 Series specifications summary
CPU
LGA1155 socket for Intel® 3rd/2nd Generation Core™ i7 / i5 / i3 /
Pentium® / Celeron® processors
Supports 22/32nm CPU
Supports Intel® Turbo Boost technology 2.0
* The Intel® Turbo Boost technology 2.0 support depends on the
CPU types.
Chipset
Memory
Intel® H61 Express Chipset
2 x DIMMs, max. 16GB, DDR3 2200(O.C.)/2133(O.C.)/2000(O.C.)/
1866(O.C.)/1600/1333/1066 MHz, non-ECC, un-buffered memory
Dual-channel memory architecture
Supports Intel® Extreme Memory Profile (XMP)
*
DDR3 1600 MHz and higher memory frequency is supported by
Intel® 3rd generation processors.
** Due to the CPU behavior, DDR3 2133/1866 MHz memory module
will run at DDR3 2000/1800 MHz frequency.
Vendors List).
****When you install a total memory of 4GB capacity or more,
Windows® 32-bit operating system may only recognize less than
3GB. We recommend a maximum of 3GB system memory if you
are using a Windows® 32-bit operating system.
Expansion slots
1 x PCI Express 3.0*/2.0 x16 slot [blue] (at x16 mode)
2 x PCI Express 2.0 x1 slots
3 x PCI slots
* PCIe 3.0 speed is supported by Intel® 3rd generation Core™
processors.
Intel® H61 Express Chipset:
Storage
4 x Serial ATA 3.0 Gb/s connectors
Realtek® 8111F Gigabit LAN controller
LAN
Audio
Realtek® ALC887 8-channel* High Definition Audio CODEC
*
Use a chassis with HD audio module in the front panel to support
an 8-channel audio output.
USB
P8H61 R2.0 and P8H61 PLUS R2.0:
Intel® H61 Express Chipset:
-
10 x USB 2.0/1.1 ports (6 ports at the mid-board, 4 ports at
the back panel)
P8H61/USB3 R2.0:
ASMedia® ASM1042 controller - supports ASUS USB 3.0 Boost
UASP Mode
-
2 x USB 3.0/2.0 ports (at the back panel, blue)
Intel® H61 Express Chipset:
-
8 x USB 2.0/1.1 ports (6 ports at the mid-board, 2 ports at the
back panel)
(continued on the next page)
viii
P8H61 R2.0 Series specifications summary
Special features
100% All High-quality Conductive Polymer Capacitors
(P8H61/USB3 R2.0 and P8H61 PLUS R2.0 only)
ASUS unique features ASUS DIGI+ VRM:
-
-
Digital Power Control: Digital Power Design for the CPU
ASUS 3+1 Phase Power Design
ASUS Exclusive Features:
-
Network iControl* featuring instant network bandwidth
domination for top network program in use
USB 3.0 Boost featuring the latest USB 3.0 UASP standard
(P8H61/USB3 R2.0 only)
-
-
-
-
-
-
-
-
-
-
Disk Unlocker featuring 3TB+ HDD support
ASUS Anti-Surge Protection
ASUS EPU
ASUS TurboV
ASUS AI Charger+ (P8H61/USB3 R2.0 only)
ASUS AI Charger
ASUS AI Suite II
ASUS Low EMI
ASUS ESD
ASUS Quiet Thermal Solution:
-
-
ASUS Fan Xpert
ASUS Fanless Design: Stylish Heatsink solution
ASUS EZ DIY:
-
-
-
-
*
ASUS UEFI BIOS featuring friendly graphics user interface
ASUS CrashFree BIOS 3
ASUS EZ Flash 2
ASUS MyLogo 2™
The Network iControl feature does not support Windows®
XP/Vista operating systems.
ASUS exclusive
Precision Tweaker:
overclocking features
-
-
-
-
vCore: Adjustable CPU voltage at 0.005V increment
vCCSA: 190-step system agent voltage control
vDRAM Bus: 190-step Memory voltage control
vPCH: 190-step Chipset voltage control
SFS (Stepless Frequency Selection):
-
BCLK/PCIE frequency tuning from 80MHz up to 300MHz at
1MHz increment
Overclocking protection:
-
ASUS C.P.R. (CPU Parameter Recall)
(continued on the next page)
ix
P8H61 R2.0 Series specifications summary
Rear panel ports
1 x PS/2 Mouse port (green)
1 x PS/2 Keyboard port (purple)
1 x COM port
1 x LPT port
1 x LAN (RJ-45) port
3 x Audio jacks
P8H61 R2.0 and P8H61 PLUS R2.0:
-
4 x USB 2.0/1.1 ports
P8H61/USB3 R2.0:
-
-
2 x USB 3.0/2.0 ports
2 x USB 2.0/1.1 ports
Internal connectors/
switches/ buttons
3 x USB 2.0/1.1 connectors support additional 6 USB 2.0/1.1
ports
4 x SATA 3.0 Gb/s connectors
1 x CPU fan connector
1 x Chassis fan connector
1 x Front panel audio connector
1 x S/PDIF Out connector
1 x System panel connector
1 x 24-pin EATX power connector
1 x 4-pin ATX 12V power connector
BIOS features
64 Mb Flash ROM, UEFI BIOS, PnP, DMI v2.0, WfM 2.0, ACPI
v2.0a, SM BIOS v2.6, Multi-language BIOS, ASUS EZ Flash
2, ASUS CrashFree BIOS 3, F12 PrintScreen function, F3
Shortcut function, and ASUS DRAM SPD (Serial Presence
Detect) memory information
Manageability
Accessories
WfM 2.0, DMI 2.0, WOR by PME, PXE
2 x Serial ATA 3.0Gb/s cables
1 x I/O shield
1 x User Manual
1 x Support DVD
Support DVD
Drivers
ASUS utilities
ASUS Update
Anti-virus software (OEM version)
Form factor
ATX form factor: 12 in x 7.8 in (30.5 cm x 19.8 cm)
* Specifications are subject to change without notice.
x
Chapter 1
Product introduction
1.1
Welcome!
Thank you for buying an ASUS® P8H61 R2.0 Series motherboard!
The motherboard delivers a host of new features and latest technologies, making it another
standout in the long line of ASUS quality motherboards!
Before you start installing the motherboard, and hardware devices on it, check the items in
your package with the list below.
1.2
Package contents
Check your motherboard package for the following items.
Motherboard
Cables
ASUS P8H61 R2.0 Series motherboard
2 x Serial ATA 3.0Gb/s cables
1 x I/O shield
Accessories
Application DVD
Documentation
ASUS motherboard support DVD
User Manual
•
•
P8H61 R2.0 Series motherboards include P8H61 R2.0, P8H61 PLUS R2.0, and
P8H61/USB3 R2.0 three models. The package contents vary from models. The layout
illustrations in this user guide are for P8H61/USB3 R2.0 only.
If any of the items is damaged or missing, contact your retailer.
1.3
Special features
1.3.1
Product highlights
LGA1155 socket for Intel® 3rd/2nd Generation Core™ i7 /
Core™ i5 / Core™ i3 / Pentium® / Celeron® Processors
This motherboard supports the Intel® 3rd/2nd generation Core™ i7/i5/
i3/Pentium®/Celeron® processors in the LGA1155 package, with iGPU,
memory, and PCI Express controllers integrated to support onboard
graphics out with dedicated chipsets, 2-channel (2 DIMMs) DDR3
memory, and 16 PCI Express 3.0/2.0 lanes. This provides great graphics
performance. Intel® 3rd/2nd generation Core™ i7/i5/i3/Pentium®/Celeron®
processors are among the most powerful and energy efficient CPUs in
the world.
Chapter 1: Product introduction
1-1
Intel® H61 Express Chipset
The Intel® H61 Express Chipset is the latest single-chipset design to
support the new 1155 socket Intel® 3rd/2nd Generation Core™ i7 /
Core™ i5 / Core™ i3 / Pentium® / Celeron® processors. It provides
improved performance by utilizing serial point-to-point links, which allows
increased bandwidth and stability.
Dual-Channel DDR3 2200(O.C.) / 2133(O.C.) / 2000(O.C.) /
1866(O.C.) / 1600 / 1333 / 1066MHz support
The motherboard supports DDR3 memory that features data transfer
rates of 2200(O.C.) / 2133(O.C.) / 2000(O.C.) / 1866(O.C.) / 1600 / 1333/
1066 MHz to meet the higher bandwidth requirements of the latest 3D
graphics, multimedia, and Internet applications. The dual-channel DDR3
architecture enlarges the bandwidth of your system memory to boost
system performance.
•
DDR3 1600 MHz and higher memory frequency is supported by Intel® 3rd generation
processors.
•
Due to the CPU behavior, DDR3 2133/1866 memory module will run at DDR3
2000/1800 MHz frequency.
PCI Express® 3.0
PCI Express® 3.0 (PCIe 3.0) is the latest PCI Express bus standard with
improved encoding schemes that provide twice the performance of the
current PCIe 2.0. The total bandwidth for a x16 link reaches a maximum
of 32Gb/s, double the 16 Gb/s of PCIe 2.0 (in x16 mode). As such, PCIe
3.0 provides users an unprecendented data speeds, combined with the
convenience and seamless transition offerred by complete backward
compatibility with PCIe 1.0 and PCIe 2.0 devices. PCIe 3.0 will become
a must-have feature for users who wish to improve and optimize graphic
performance, as well as have the latest technology available to them.
* PCI 3.0 speed is supported by Intel® 3rd generation Core™ processors.
8-channel high definition audio
The onboard 8-channel HD audio (High Definition Audio, previously
codenamed Azalia) CODEC enables high-quality 192KHz/24-bit audio
output and jack-detect feature that automatically detects and identifies
what types of peripherals are plugged into the audio I/O jacks and notifies
users of inappropriate connection, which means there will be no more
confusion of Line-in, Line-out, and Mic jacks.
Gigabit LAN solution
The onboard LAN controller is a highly integrated Gb LAN controller. It is
enhanced with an ACPI management function to provide efficient power
management for advanced operating systems.
1-2
ASUS P8H61 R2.0 Series
100% All High-quality Conductive Polymer Capacitors
(P8H61/USB3 R2.0 and P8H61 PLUS R2.0 only)
This motherboard uses all high-quality conductive polymer capacitors for
durability, improved lifespan, and enhanced thermal capacity.
1.3.2
ASUS DIGI+ VRM
Digital Power Control: Digital Power Design for the CPU
All-new digital CPU power controls work perfectly together to match
digital power signal (SVID) requests from the CPU, with ultra-fast sensing
and response efficiently delivering precision power. Accurate delivery
reduces waste, and provides more stable CPU Vcore voltages. Users can
adjust the CPU voltage for various overclocking scenarios, with accurate
input through UEFI BIOS tuning or the exclusive ASUS interface. This
proprietary design increases overclocking headroom to push performance
to its full potential.
EPU
Tap into the world’s first real-time PC power saving chip through the AI
Suite II utility. Get total system-wide energy optimization by automatically
detecting current PC loadings and intelligently moderating power
consumption. This also reduces fan noise and extends component
longevity.
1.3.3
Innovative ASUS features
ASUS UEFI BIOS
Flexible and Easy BIOS Interface
ASUS UEFI BIOS offers the first mouse-controlled graphical BIOS
designed with selectable modes, providing a user-friendly interface
that goes beyond the traditional keyboard-only controls. It also natively
supports fully-utilized hard drives larger than 2.2TB in 64-bit operating
systems.
ASUS exclusive interface
EZ Mode displays frequently-accessed info. Users can choose system
performance settings, and drag and drop boot priorities. Advanced Mode
for performance enthusiasts includes detailed DRAM settings via a
dedicated memory info page for complete insight.
New upgrade! Quick and easy information for enhanced system
control
- F12 BIOS snapshot hotkey for sharing UEFI information and
troubleshooting
- New F3 Shortcut for most accessed information
- ASUS DRAM SPD (Serial Presence Detect) information for accessing
memory information, detecting faulty DIMMs, and helping with difficult
POST situations.
Chapter 1: Product introduction
1-3
ASUS TurboV
Feel the adrenaline rush of real-time OC-now a reality with the ASUS
TurboV. This easy OC tool allows you to overclock without exiting or
rebooting the OS; and its user-friendly interface makes overclock with just
a few clicks away. Moreover, the ASUS OC profiles in TurboV provides
the best O.C. settings in different scenarios.
USB 3.0 Boost (P8H61/USB3 R2.0 only)
New ASUS USB 3.0 Boost technology supports UASP (USB Attached
SCSI Protocol), the latest USB 3.0 standard. With USB 3.0 Boost
technology, a USB device’s transmission speed is significantly increased
up to 170%, adding to an already impressive fast USB 3.0 transfer speed.
ASUS software automatically accelerates data speeds for compatible
USB 3.0 peripherals without the need for any user interaction.
Network iControl
With a one-click on/off button, the software currently in use is set as
top priority over all other network programs, dominating the network
bandwidth with ease. Moreover, you can prioritize your favorite software
easily by configuring profiles through the intutive user interface. Within
the profile, programs can be pre-scheduled to run in a specific time period
to avoid network clogging and long-waits on downloads. Auto PPPoE
network connection gives a one-step setup and an intuitive network
bandwidth control center.
The Network iControl feature does not support Windows® XP/Vista operating systems.
ASUS Anti-Surge Protection
This special design prevents expensive devices and the motherboard
from damage caused by power surges from switching power supply
(PSU).
AI Suite II
With its fast user-friendly interface, ASUS AI Suite II consolidates all the
exclusive ASUS features into one simple to use software package. It
allows you to supervise overclocking, energy management, fan speed
control, and voltage and sensor readings. This all-in-one software offers
diverse and ease to use functions, with no need to switch back and forth
between different utilities.
Fan Xpert
ASUS Fan Xpert intelligently allows you to adjust the CPU and chassis
fan speeds according to different ambient temperatures caused by
different climate conditions in different geographic regions and your PC’s
loading. The built-in variety of useful profiles offer flexible controls of fan
speed to achieve a quiet and cool environment.
1-4
ASUS P8H61 R2.0 Series
Ai Charger
Ai Charger is ASUS fast-charging software that supports iPod, iPhone,
and iPad.
•
•
Check your USB mobile device if it fully supports the BC 1.1 function.
The actual charging speed may vary with your USB device’s conditions.
Ai Charger+ (P8H61/USB3 R2.0 only)
ASUS Ai Charger+, the latest Ai Charger* version, brings you to a new
level of USB 3.0 fast charging experience. With its easy and user-friendly
interface, you can not only easily charge iPod, iPhone and iPad, but also
BC 1.1** standard mobile devices three times*** as fast as before.
*
Ai Charger is ASUS unique fast-charging software which supports iPod, iPhone and
iPad.
** Check your USB mobile device manufacturer if it fully supports the BC 1.1 function.
***The actual charging speed may vary with your USB device’s conditions.
Low EMI
A special low-radiation design shields you from harmful electromagnetic
exposure by eliminating 50% of radiation.
1. Radiation Deduction Design minimizes harmful electromagnetic
radiation output with exclusive circuit design to cancel electrical
charge.
2. The Radiation Moat Design effectively blocks radiation to prevent
discharge spread.
ESD
Protect your computer with ESD Guards. Electrostatic discharge
(ESD) conditions can happen while plugging or unplugging any USB
peripherals-causing damage to the computer. ASUS ESD Guards clamp
the ESD voltage and shunt the majority of the ESD current away for a
more reliable computing environment.
ASUS CrashFree BIOS 3
ASUS CrashFree BIOS 3 is an auto-recovery tool that allows you to
restore a corrupted BIOS file using the bundled support DVD or USB
flash disk that contains the latest BIOS file.
ASUS EZ Flash 2
ASUS EZ Flash 2 is a utility that allows you to update the BIOS without
using an OS-based utility.
Chapter 1: Product introduction
1-5
C.P.R. (CPU Parameter Recall)
The BIOS C.P.R. feature automatically restores the CPU default settings
when the system hangs due to overclocking failure. C.P.R. eliminates the
need to open the system chassis and clear the RTC data. Simply shut
down and reboot the system, and the BIOS automatically restores the
CPU parameters to their default settings.
ErP ready
The motherboard is European Union´s Energy-related Products (ErP)
ready, and ErP requires products to meet certain energy efficiency
requirements in regards to energy consumptions. This is in line with
ASUS vision of creating environment-friendly and energy-efficient
products through product design and innovation to reduce carbon
footprint of the product and thus mitigate environmental impacts.
1.4
Before you proceed
Take note of the following precautions before you install motherboard components or change
any motherboard settings.
•
•
Unplug the power cord from the wall socket before touching any component.
Before handling components, use a grounded wrist strap or touch a safely grounded
object or a metal object, such as the power supply case, to avoid damaging them due to
static electricity.
•
•
Hold components by the edges to avoid touching the ICs on them.
Whenever you uninstall any component, place it on a grounded antistatic pad or in the
bag that came with the component.
•
Before you install or remove any component, ensure that the ATX power supply is
switched off or the power cord is detached from the power supply. Failure to do so may
cause severe damage to the motherboard, peripherals, or components.
Standby Power LED
The motherboard comes with a standby power LED that lights up to indicate that the system
is ON, in sleep mode, or in soft-off mode. This is a reminder that you should shut down
the system and unplug the power cable before removing or plugging in any motherboard
component. The illustration below shows the location of the onboard LED.
P8H61/USB3 R2.0
SB_PWR
ON
OFF
Standby Power Powered Off
P8H61/USB3 R2.0 Onboard LED
1-6
ASUS P8H61 R2.0 Series
1.5
Motherboard overview
Before you install the motherboard, study the configuration of your chassis to ensure that the
motherboard fits into it.
Ensure that you unplug the power cord before installing or removing the motherboard.
Failure to do so can cause you physical injury and damage motherboard components.
1.5.1
Placement direction
When installing the motherboard, ensure that you place it into the chassis in the correct
orientation. The edge with external ports goes to the rear part of the chassis as indicated in
the image below.
1.5.2
Screw holes
Place six screws into the holes indicated by circles to secure the motherboard to the chassis.
Do not overtighten the screws! Doing so can damage the motherboard.
Place this side towards
the rear of the chassis
P8H61/USB3 R2.0
Chapter 1: Product introduction
1-7
1.5.3
Motherboard layout
1
2
3
2
4
19.8cm(7.8in)
KBMS
CPU_FAN
DIGI+
VRM
ATX12V
USB3_12
LAN_USB12
1
CHA_FAN
Lithium Cell
CMOS Power
AUDIO
ASM
1042
P8H61/USB3 R2.0
RTL
8111F
PCIEX16
PCIEX1_1
PCIEX1_2
ASM
1083
Intel®
H61
Super
I/O
PCI1
5
6
64Mb
BIOS
PCI2
CLRTC
ALC
887
PCI3
SATA3G_4 SATA3G_3
SATA3G_2 SATA3G_1
SPDIF_OUT
SB_PWR
USB56
USB78
USB910
PANEL
AAFP
11
10
9
8
7
1-8
ASUS P8H61 R2.0 Series
1
2
3
2
4
19.8cm(7.8in)
KBMS
CPU_FAN
DIGI+
VRM
ATX12V
USB34
LAN_USB12
1
CHA_FAN
Lithium Cell
CMOS Power
AUDIO
P8H61 PLUS R2.0
RTL
8111F
PCIEX16
PCIEX1_1
ASM
1083
Intel®
H61
PCIEX1_2
Super
I/O
PCI1
5
6
64Mb
BIOS
PCI2
CLRTC
ALC
887
PCI3
SATA3G_4 SATA3G_3
SATA3G_2 SATA3G_1
SPDIF_OUT
AAFP
SB_PWR
USB56
USB78
USB910
PANEL
11
10
9
8
7
Chapter 1: Product introduction
1-9
1
2
3
2
4
19.8cm(7.8in)
KBMS
CPU_FAN
DIGI+
VRM
ATX12V
USB34
LAN_USB12
1
CHA_FAN
Lithium Cell
CMOS Power
AUDIO
P8H61 R2.0
RTL
8111F
PCIEX16
PCIEX1_1
ASM
1083
Intel®
H61
PCIEX1_2
Super
I/O
PCI1
5
6
64Mb
BIOS
PCI2
CLRTC
ALC
887
PCI3
SATA3G_4 SATA3G_3
SATA3G_2 SATA3G_1
SPDIF_OUT
AAFP
SB_PWR
USB56
USB78
USB910
PANEL
11
10
9
8
7
1.5.4
Layout contents
Connectors/Jumpers/Slots/LED
Page
Connectors/Jumpers/Slots/LED
Page
1.
2.
3.
ATX power connectors (24-pin EATXPWR,
4-pin ATX12V)
1-28 7.
System panel connector (20-8 pin PANEL)
1-32
CPU and chassis fan connectors
(4-pin CPU_FAN, 3-pin CHA_FAN)
1-29 8.
USB 2.0 connectors (10-1 pin USB56,
USB78, USB910)
1-31
Intel® LGA1155 CPU socket
1-11
9.
Digital audio connector (4-1 pin SPDIF_OUT) 1-29
4.
5.
6.
DDR3 DIMM slots
1-16 10. Front panel audio connector (10-1 pin AAFP) 1-27
Clear RTC RAM (3-pin CLRTC)
1-25 11. Standby power LED (SB_PWR)
1-30
1-6
Intel® H61 Serial ATA 3.0Gb/s connectors
(7-pin SATA3G_1/2/3/4)
1-10
ASUS P8H61 R2.0 Series
1.6
Central Processing Unit (CPU)
The motherboard comes with a surface mount LGA1155 socket designed for the Intel® 3rd /
2nd Generation Core™ i7 / i5 / i3 / Pentium® / Celeron® processors.
Unplug all power cables before installing the CPU.
•
Upon purchase of the motherboard, ensure that the PnP cap is on the socket and the
socket contacts are not bent. Contact your retailer immediately if the PnP cap is missing,
or if you see any damage to the PnP cap/socket contacts/motherboard components.
ASUS will shoulder the cost of repair only if the damage is shipment/transit-related.
•
•
Keep the cap after installing the motherboard. ASUS will process Return Merchandise
Authorization (RMA) requests only if the motherboard comes with the cap on the
LGA1155 socket.
The product warranty does not cover damage to the socket contacts resulting from
incorrect CPU installation/removal, or misplacement/loss/incorrect removal of the PnP
cap.
1.6.1
Installing the CPU
To install a CPU:
1. Locate the CPU socket on the motherboard.
P8H61/USB3 R2.0
P8H61/USB3 R2.0 CPU socket LGA1155
2.
Press the load lever with your thumb (A),
and then move it to the right (B) until it is
released from the retention tab.
Load lever
A
To prevent damage to the socket pins,
do not remove the PnP cap unless
you are installing a CPU.
B
Retention tab
Chapter 1: Product introduction
1-11
3.
4.
5.
Lift the load lever in the direction of the
arrow until the load plate is completely
lifted.
Load plate
Remove the PnP cap from the CPU
socket by lifting the tab only.
PnP cap
Position the CPU over the socket,
ensuring that the gold triangle is on the
bottom-left corner of the socket, and
then fit the socket alignment keys into
the CPU notches.
CPU notches
The CPU fits in only one correct
orientation. DO NOT force the CPU
into the socket to prevent bending
the connectors on the socket and
damaging the CPU!
Gold
triangle
mark
Alignment keys
1-12
ASUS P8H61 R2.0 Series
6.
Apply some Thermal Interface Material
to the exposed area of the CPU that the
heatsink will be in contact with, ensuring
that it is spread in an even thin layer.
Some heatsinks come with pre-
applied thermal paste. If so, skip this
step.
The Thermal Interface Material is
toxic and inedible. DO NOT eat it. If
it gets into your eyes or touches your
skin, wash it off immediately, and seek
professional medical help.
7.
Close the load plate (A), and then push
down the load lever (B), ensuring that
the front edge of the load plate slides
under the retention knob (C).
B
A
C
8.
Insert the load lever under the retention
tab.
Chapter 1: Product introduction
1-13
1.6.2
Installing the CPU heatsink and fan
The Intel® LGA1155 processor requires a specially designed heatsink and fan assembly to
ensure optimum thermal condition and performance.
•
When you buy a boxed Intel® processor, the package includes the CPU fan and
heatsink assembly. If you buy a CPU separately, ensure that you use only Intel®-certified
multi-directional heatsink and fan.
•
•
Your Intel® LGA1155 heatsink and fan assembly comes in a push-pin design and
requires no tool to install.
Use an LGA1155-compatible CPU heatsink and fan assembly only. The LGA1155 socket
is incompatible with the LGA775 and LGA1366 sockets in size and dimension.
If you purchased a separate CPU heatsink and fan assembly, ensure that you have
properly applied Thermal Interface Material to the CPU heatsink or CPU before you install
the heatsink and fan assembly.
Ensure that you have installed the motherboard to the chassis before you install the CPU
fan and heatsink assembly.
To install the CPU heatsink and fan:
A
1.
Place the heatsink on top of the installed
CPU, ensuring that the four fasteners match
the holes on the motherboard.
B
B
A
Orient the heatsink and fan assembly
such that the CPU fan cable is closest to
the CPU fan connector.
2.
Push down two fasteners at a time in a
diagonal sequence to secure the heatsink
and fan assembly in place.
1
1
A
B
B
A
The type of CPU heatsink and fan assembly may differ, but the installation steps and
functions should remain the same. The illustration above is for reference only.
1-14
ASUS P8H61 R2.0 Series
3.
Connect the CPU fan cable to the connector on the motherboard labeled CPU_FAN.
CPU_FAN
P8H61/USB3 R2.0
P8H61/USB3 R2.0 CPU fan connector
Do not forget to connect the CPU fan connector! Hardware monitoring errors can occur if
you fail to plug this connector.
1.6.3
Uninstalling the CPU heatsink and fan
To uninstall the CPU heatsink and fan:
1.
2.
3.
Disconnect the CPU fan cable from the connector on the motherboard.
Rotate each fastener counterclockwise.
Pull up two fasteners at a time in a diagonal sequence to disengage the heatsink and
fan assembly from the motherboard.
A
A
B
B
A
B
B
A
Chapter 1: Product introduction
1-15
4.
5.
Carefully remove the heatsink and fan
assembly from the motherboard.
Rotate each fastener clockwise to ensure
correct orientation when reinstalling.
1.7
System memory
1.7.1
Overview
The motherboard comes with two Double Data Rate 3 (DDR3) Dual Inline Memory Modules
(DIMM) sockets. A DDR3 module has the same physical dimensions as a DDR2 DIMM but
is notched differently to prevent installation on a DDR2 DIMM socket. DDR3 modules are
developed for better performance with less power consumption.
The figure illustrates the location of the DDR3 DIMM sockets:
Channel
Sockets
Channel A
Channel B
DIMM_A1
DIMM_B1
P8H61/USB3 R2.0
P8H61/USB3 R2.0 240-pin DDR3 DIMM sockets
1-16
ASUS P8H61 R2.0 Series
1.7.2
Memory configurations
You may install 1GB, 2GB, 4GB, and 8GB unbuffered non-ECC DDR3 DIMMs into the DIMM
sockets.
•
You may install varying memory sizes in Channel A and Channel B. The system maps
the total size of the lower-sized channel for the dual-channel configuration. Any excess
memory from the higher-sized channel is then mapped for single-channel operation.
•
•
•
According to Intel CPU specification, DIMM voltage below 1.65V is recommended to
protect the CPU.
Always install DIMMs with the same CAS latency. For optimum compatibility, we
recommend that you obtain memory modules from the same vendor.
Due to the memory address limitation on 32-bit Windows® OS, when you install 4GB
or more memory on the motherboard, the actual usable memory for the OS can be
about 3GB or less. For effective use of memory, we recommend that you do any of the
following:
- Use a maximum of 3GB system memory if you are using a 32-bit Windows® OS.
- Install a 64-bit Windows® OS when you want to install 4GB or more on the
motherboard.
•
•
This motherboard does not support DIMMs made up of 512Mb (64MB) chips or less..
The default memory operation frequency is dependent on its Serial Presence Detect
(SPD), which is the standard way of accessing information from a memory module.
Under the default state, some memory modules for overclocking may operate at a
lower frequency than the vendor-marked value. To operate at the vendor-marked or at a
higher frequency, refer to section 2.4 Ai Tweaker menu for manual memory frequency
adjustment.
•
For system stability, use a more efficient memory cooling system to support a full
memory load (2 DIMMs) or overclocking condition.
P8H61 R2.0 Series Motherboard Qualified Vendors Lists (QVL)
DDR3-2400 MHz capability
DIMM socket
support (Optional)
SS/ Chip
Vendors
Part No.
Size
Chip NO. Timing
Voltage
DS
Brand
1 DIMM 2 DIMMs
CORSAIR
G.SKILL
G.SKILL
GEIL
CMGTX8(XMP)
8GB(2GB x 4)
SS
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
10-12-10-27 1.65V
11-11-11-31 1.65V
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
F3-19200CL11Q-16GBZHD(XMP1.3) 16GB(4GB x 4) DS
F3-19200CL9D-4GBPIS(XMP)
GET34GB2400C9DC(XMP)
4GB(2x 2GB)
2GB
DS
DS
SS
SS
SS
DS
9-11-9-28
9-11-9-27
1.65V
1.65V
KINGMAX
Transcend
Transcend
Transcend
FLLE88F-C8KKAA HAIS(XMP)
TX2400KLU-4GK(427652)(XMP)
TX2400KLU-4GK (381850)(XMP)
TX2400KLU-4GK(374243)(XMP)
2GB
10-11-10-30 1.8V
4GB(2 x 2GB)
4GB(2x 2GB)
4GB(2x 2GB)
-
1.65V
1.65V
1.65V
9
9
PATRIOT
PVV34G2400C9K(XMP)
4GB(2x 2GB)
DS
-
-
9-11-9-27
1.65V
•
•
•
DDR3 1600 MHz and higher memory frequency is supported by Intel® 3rd generation
processors.
•
Due to the CPU behavior, DDR3 2133/1866 memory module will run at DDR3
2000/1800 MHz frequency.
Chapter 1: Product introduction
1-17
DDR3-2250 MHz capability
DIMM socket support
(Optional)
Vendors
Part No.
Size
SS/DS Chip Brand Chip NO. Timing Voltage
1 DIMM
2 DIMMs
KINGSTON KHX2250C9D3T1K2/4GX(XMP) 4GB(2 x 2GB) DS
-
-
-
1.65V
•
•
DDR3-2200 MHz capability
DIMM socket support
(Optional)
Vendors
Part No.
Size
SS/DS Chip Brand Chip NO. Timing
Voltage
1 DIMM
2 DIMMs
GEIL
GEIL
GET34GB2200C9DC(XMP)
2GB
DS
DS
-
-
-
-
9-10-9-28 1.65V
•
•
•
•
GET38GB2200C9ADC(XMP) 4GB
9-11-9-28
-
1.65V
KINGMAX
FLKE85F-B8KJA FEIH(XMP) 4GB(2 x 2GB) DS
-
-
1.5V-1.7V
•
•
DDR3-2133 MHz capability
DIMM socket
support (Optional)
SS/ Chip
Vendors
Part No.
Size
Chip NO. Timing
Voltage
DS
Brand
1 DIMM 2 DIMMs
A-DATA
CORSAIR
CORSAIR
CORSAIR
CORSAIR
G.SKILL
GEIL
AX3U2133GC2G9B-DG2(XMP)
2GB
SS
DS
DS
DS
DS
DS
DS
DS
DS
DS
DS
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
9-11-9-27 1.55~1.75V
9-11-10-27 1.50V
9-10-9-24 1.65V
9-10-9-27 1.50V
9-11-9-27 1.50V
9-11-10-28 1.65V
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
CMT16GX3M4X2133C9(XMP 1.3) 16GB(4GB x 4)
CMT4GX3M2A2133C9(XMP)
CMT4GX3M2B2133C9(XMP)
CMT8GX3M2B2133C9(XMP)
4GB(2 x 2GB)
4GB(2 x 2GB)
8GB(4GB x 2)
F3-17000CL9Q-16GBZH(XMP1.3) 16GB(4GB x 4)
GE34GB2133C9DC(XMP)
GU34GB2133C9DC(XMP)
2GB
9-9-9-28
9-9-9-28
-
1.65V
1.65V
1.65V
GEIL
4GB(2 x 2GB)
4GB(2 x 2GB)
KINGSTON KHX2133C9AD3T1K2/4GX(XMP)
KINGSTON KHX2133C9AD3X2K2/4GX(XMP) 4GB(2 x 2GB)
KINGSTON KHX2133C9AD3T1K4/8GX(XMP) 8GB(4 x 2GB)
9-11-9-27 1.65V
9-11-9-27 1.65V
KINGSTON KHX2133C9AD3T1FK4/8GX(XMP) 8GB(4x 2GB)
DS
-
-
-
1.65V
•
•
DDR3-2000 MHz capability
DIMM socket
support (Optional)
SS/ Chip
DS Brand
Vendors
Part No.
Size
Chip NO.
Timing
Voltage
1.65V
1 DIMM 2 DIMMs
Apacer
78.AAGD5.9KD(XMP)
6GB(3 x 2GB) DS
4GB(2 x 2GB) DS
6GB(3 x 2GB) DS
4GB(2 x 2GB) DS
4GB(2 x 2GB) DS
6GB(3 x 2GB) DS
4GB(2 x 2GB) DS
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
9-9-9-27
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
CORSAIR CMZ4GX3M2A2000C10(XMP)
CORSAIR CMT6GX3M3A2000C8(XMP)
10-10-10-27 1.50V
8-9-8-24
1.65V
1.65V
1.65V
1.65V
1.65V
1.65V
1.65V
1.65V
1.65V
1.65V
1.6V
•
•
•
•
•
•
•
•
•
•
•
•
G.SKILL
G.SKILL
G.SKILL
GEIL
F3-16000CL9D-4GBFLS(XMP)
F3-16000CL9D-4GBTD(XMP)
F3-16000CL6T-6GBPIS(XMP)
GUP34GB2000C9DC(XMP)
9-9-9-24
9-9-9-27
6-9-6-24
9-9-9-28
KINGSTON KHX2000C9AD3T1K2/4GX(XMP) 4GB(2 x 2GB) DS
KINGSTON KHX2000C9AD3W1K2/4GX(XMP) 4GB(2 x 2GB) DS
KINGSTON KHX2000C9AD3T1K2/4GX(XMP) 4GB(2 x 2GB) DS
KINGSTON KHX2000C9AD3W1K3/6GX(XMP) 6GB(3 x 2GB) DS
KINGSTON KHX2000C9AD3T1K3/6GX(XMP) 6GB(3 x 2GB) DS
-
-
9
-
-
-
-
Transcend TX2000KLN-8GK(XMP)
Asint SLA302G08-ML2HB(XMP)
8GB(2 x 4GB) DS
4GB
DS HYNIX H5TQ2G83BFR H9C
-
DDR3-1866 MHz capability
DIMM socket
support (Optional)
SS/ Chip
DS Brand
Vendors
Part No.
Size
Chip NO. Timing
Voltage
1 DIMM 2 DIMMs
CORSAIR
CORSAIR
CORSAIR
G.SKILL
G.SKILL
G.SKILL
G.SKILL
CMT4GX3M2A1866C9(XMP)
CMT6GX3MA1866C9(XMP)
CMZ8GX3M2A1866C9(XMP)
F3-14900CL9Q-16GBZL(XMP1.3)
4GB(2 x 2GB)
6GB(3 x 2GB)
8GB(2 x 4GB)
DS
DS
DS
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
9-9-9-24
1.65V
1.65V
1.50V
1.5V
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
9-9-9-24
9-10-9-27
9-10-9-28
16GB(4GB x 4) DS
F3-14900CL10Q2-64GBZLD(XMP1.3) 64GB(8GB x 8) DS
10-11-10-30 1.5V
F3-14900CL9D-8GBXL(XMP)
F3-14900CL9Q-8GBXL(XMP)
8GB(2 x 4GB)
8GB(2GB x 4)
3GB(3 x 1GB)
DS
DS
SS
9-10-9-28
1.5V
9-9-9-24
1.6V
KINGSTON KHX1866C9D3T1K3/3GX(XMP)
KINGSTON KHX1866C9D3K4/16GX(XMP)
-
-
1.65V
1.65V
16GB(4GB x 4) DS
6GB(3 x 2GB) DS
KINGSTON KHX1866C9D3T1K3/6GX(XMP)
-
-
-
1.65V
•
•
1-18
ASUS P8H61 R2.0 Series
DDR3-1600 MHz capability
DIMM socket
support (Optional)
SS/ Chip
DS Brand
Vendors
Part No.
Size
Chip NO.
Timing Voltage
1 DIMM 2 DIMMs
3CCD-1509A
EL1126T
A-DATA
A-DATA
A-DATA
AM2U16BC2P1
2GB
SS A-DATA
-
-
•
•
•
•
AD31600E001GM(O)U3K
AM2U16BC4P2
3GB(3 x 1GB) SS
-
-
8-8-8-24 1.65V-1.85V
3CCD-1509A
EL1126T
4GB DS A-DATA
-
-
•
A-DATA
AX3U1600GC4G9-2G(XMP)
AX3U1600XC4G79-2X(XMP)
TR3X3G1600C8D(XMP)
8GB(2 x 4GB) DS
8GB(2 x 4GB) DS
3GB(3 x 1GB) SS
12GB(6x2GB) DS
4GB(2 x 2GB) DS
4GB(2 x 2GB) DS
4GB(2 x 2GB) DS
4GB(2 x 2GB) DS
4GB(2 x 2GB) DS
6GB(3 x 2GB) DS
6GB(3 x 2GB) DS
6GB(3 x 2GB) DS
8GB(2 x 4GB) DS
8GB(2 x 4GB) DS
8GB(4 x 2GB) DS
6GB(3 x 2GB) DS
2GB(2 x 1GB) SS
4GB(2 x 2GB) SS
4GB(2 x 2GB) DS
4GB(2 x 2GB) DS
4GB(2 x 2GB) DS
4GB(2 x 2GB) DS
6GB(3 x 2GB) DS
8GB(2 x 4GB) DS
8GB(2 x 4GB) DS
8GB(2 x 4GB) DS
16GB(4 x 4GB) DS
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
9-9-9-24 1.55V-1.75V
7-9-7-21 1.55V-1.75V
8-8-8-24 1.65V
8-8-8-24 1.65V
8-8-8-24 1.65V
9-9-9-24 1.65V
7-8-7-20 1.65V
9-9-9-24 1.65V
9-9-9-24 1.65V
8-8-8-24 1.65V
8-8-8-24 1.65V
9-9-9-24 1.65V
9-9-9-24 1.65V
7-8-7-20 1.50V
9-9-9-24 1.65V
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
A-DATA
CORSAIR
CORSAIR
CORSAIR
CORSAIR
CORSAIR
CORSAIR
CORSAIR
CORSAIR
CORSAIR
CORSAIR
CORSAIR
CORSAIR
CORSAIR
Crucial
CMD12GX3M6A1600C8(XMP)
CMP4GX3M2A1600C8(XMP)
CMP4GX3M2A1600C9(XMP)
CMP4GX3M2C1600C7(XMP)
CMX4GX3M2A1600C9(XMP)
CMX4GX3M2A1600C9(XMP)
TR3X6G1600C8 G(XMP)
•
•
•
•
•
•
•
•
•
•
TR3X6G1600C8D G(XMP)
TR3X6G1600C9 G(XMP)
CMP8GX3M2A1600C9(XMP)
CMZ8GX3M2A1600C7R(XMP)
CMX8GX3M4A1600C9(XMP)
BL25664BN1608.16FF(XMP)
F3-12800CL9D-2GBNQ(XMP)
F3-12800CL7D-4GBRH(XMP)
F3-12800CL7D-4GBRM(XMP)
F3-12800CL8D-4GBRM(XMP)
F3-12800CL9D-4GBECO(XMP)
F3-12800CL9D-4GBRL(XMP)
F3-12800CL9T-6GBNQ(XMP)
F3-12800CL7D-8GBRH(XMP)
F3-12800CL8D-8GBECO(XMP)
F3-12800CL9D-8GBRL(XMP)
GET316GB1600C9QC(XMP)
•
•
•
•
•
•
-
-
G.SKILL
G.SKILL
G.SKILL
G.SKILL
G.SKILL
G.SKILL
G.SKILL
G.SKILL
G.SKILL
G.SKILL
GEIL
9-9-9-24 1.5V
7-7-7-24 1.6V
7-8-7-24 1.6V
8-8-8-24 1.60V
9-9-9-24 XMP 1.35V
9-9-9-24 1.5V
•
•
•
•
•
•
9-9-9-24 1.5V~1.6V
7-8-7-24 1.6V
8-8-8-24 XMP 1.35V
9-9-9-24 1.5V
9-9-9-28 1.6V
H5TQ2G83CFR
PBC
HYNIX
HMT351U6CFR8C-PB
4GB
DS HYNIX
-
-
•
•
KINGMAX
KINGMAX
KINGMAX
FLGD45F-B8MF7 MAEH(XMP)
FLGE85F-B8KJ9A FEIS(XMP)
FLGE85F-B8MF7 MEEH(XMP)
1GB
2GB
2GB
SS
DS
DS
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
7
-
-
•
•
•
•
•
•
•
•
-
•
7
-
-
KINGSTON KHX1600C9D3P1K2/4G
4GB(2 x 2GB) SS
12GB(3x4GB) DS
1.5V
•
•
KINGSTON KHX1600C9D3K3/12GX(XMP)
9-9-9-27 1.65V
9-9-9-27 1.65V
KINGSTON KHX1600C9D3T1BK3/12GX(XMP) 12GB(3x4GB) DS
KINGSTON KHX1600C9D3K4/16GX(XMP)
KINGSTON KHX1600C9AD3/2G
16GB(4GB x 4) DS
-
-
1.65V
1.65V
•
•
2GB
DS
11-11-
11-28
KINGSTON KVR1600D3N11/2G-ES
2GB
DS KTC
D1288JPNDPLD9U
1.35V-1.5V
•
KINGSTON KHX1600C7D3K2/4GX(XMP)
KINGSTON KHX1600C8D3K2/4GX(XMP)
KINGSTON KHX1600C8D3T1K2/4GX(XMP)
KINGSTON KHX1600C9D3K2/4GX(XMP)
KINGSTON KHX1600C9D3LK2/4GX(XMP)
KINGSTON KHX1600C9D3X2K2/4GX(XMP)
KINGSTON KHX1600C9D3T1K3/6GX(XMP)
KINGSTON KHX1600C9D3K3/6GX(XMP)
4GB(2 x 2GB) DS
4GB(2 x 2GB) DS
4GB(2 x 2GB) DS
4GB(2 x 2GB) DS
4GB(2 x 2GB) DS
4GB(2 x 2GB) DS
6GB(3 x 2GB) DS
6GB(3 x 2GB) DS
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
1.65V
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
8
8
9
9
1.65V
1.65V
1.65V
XMP 1.35V
9-9-9-27 1.65V
-
1.65V
1.65V
9
KINGSTON KHX1600C9D3T1BK3/6GX(XMP) 6GB(3 x 2GB) DS
9-9-9-27 1.65V
9-9-9-27 1.65V
KINGSTON KHX1600C9D3K2/8GX(XMP)
KINGSTON KHX1600C9D3P1K2/8G
Super Talent WA160UX6G9
8GB(2 x 4GB) DS
8GB(2 x 4GB) DS
6GB(3 x 2GB) DS
-
1.5V
9
-
-
-
Transcend
Asint
JM1600KLN-8GK
8GB(4GB x 2) DS Transcend TK483PCW3
SLZ3128M8-EGJ1D(XMP)
SLA302G08-EGG1C(XMP)
SLA302G08-EGJ1C(XMP)
M2P2G64CB8HC9N-DG(XMP)
998659(XMP)
2GB
4GB
4GB
2GB
DS Asint
DS Asint
DS Asint
3128M8-GJ1D
9-9-9-24 1.6V
Asint
302G08-GG1C
-
-
-
-
-
Asint
302G08-GJ1C
-
Elixir
DS
-
-
-
-
-
-
-
-
-
Mushkin
Mushkin
PATRIOT
6GB(3 x 2GB) DS
6GB(3 x 2GB) DS
4GB(2 x 2GB) DS
9-9-9-24
998659(XMP)
9-9-9-24 1.5~1.6V
7-7-7-20 1.7V
PGS34G1600LLKA
H5TQ2G83BFR
PBC
SanMax
SMD-4G68HP-16KZ
4GB
DS HYNIX
-
-
•
•
Chapter 1: Product introduction
1-19
DDR3-1333 MHz capability
DIMM socket
support (Optional)
SS/ Chip
DS Brand
Vendors
Part No.
Size
Chip NO.
Timing Voltage
1 DIMM 2 DIMMs
AD30908C8D-151C
E0906
A-Data
A-Data
A-Data
AD31333001GOU
AD31333G001GOU
AD31333002GOU
1GB
SS A-Data
-
-
•
•
•
•
•
•
3GB(3 x 1GB) SS
-
-
8-8-8-24 1.65-1.85V
AD30908C8D-151C
E0903
2GB
DS A-Data
-
-
A-Data
AD31333G002GMU
78.A1GC6.9L1
2GB
2GB
2GB
1GB
1GB
DS
-
-
8-8-8-24 1.65-1.85V
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Apacer
DS APACER AM5D5808DEWSBG
-
-
-
Apacer
78.A1GC6.9L1
DS Apacer
AM5D5808FEQSBG
9
CORSAIR
CORSAIR
CORSAIR
CORSAIR
CORSAIR
CORSAIR
CORSAIR
Crucial
CM3X1024-1333C9DHX
CM3X1024-1333C9
TR3X3G1333C9 G
TR3X3G1333C9 G
CM3X1024-1333C9DHX
SS
SS
-
-
-
-
-
9-9-9-24 1.60V
9-9-9-24 1.60V
9-9-9-24 1.50V
9-9-9-24 1.50V
-
3GB(3 x 1GB) SS
3GB(3 x 1GB) SS
-
-
1GB
DS Corsair
-
-
-
CMD24GX3M6A1333C9(XMP) 24GB(6x4GB) DS
-
-
-
9-9-9-24 1.60V
9-9-9-24 1.50V
CMX8GX3M4A1333C9
CT12864BA1339.8FF
8GB(4 x 2GB) DS
-
1GB
2GB
SS Micron
DS Micron
9FF22D9KPT
9
9
-
-
Crucial
CT25664BA1339.16FF
BL25664BN1337.16FF (XMP)
9KF27D9KPT
-
Crucial
6GB(3 x 2GB) DS
-
7-7-7-24 1.65V
1.35V(low
voltage)
ELPIDA
ELPIDA
EBJ10UE8EDF0-DJ-F
EBJ21UE8EDF0-DJ-F
1GB
SS ELPIDA
J1108EDSE-DJ-F
J1108EDSE-DJ-F
-
•
•
•
•
1.35V(low
voltage)
2GB
1GB
DS ELPIDA
SS G.SKILL
-
-
G.SKILL
G.SKILL
G.SKILL
G.SKILL
G.SKILL
G.SKILL
G.SKILL
G.SKILL
GEIL
F3-10600CL8D-2GBHK(XMP)
F3-10666CL7T-3GBPK(XMP)
F3-10666CL9T-3GBNQ
-
-
-
-
-
-
-
-
-
-
-
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
3GB(3 x 1GB) SS
3GB(3 x 1GB) SS
4GB(2 x 2GB) DS
-
-
-
-
-
-
-
-
-
7-7-7-18 1.5~1.6V
9-9-9-24 1.5~1.6V
8-8-8-21 1.5-1.6V
8-8-8-24 XMP 1.35V
7-7-7-18 1.5~1.6V
7-7-7-21 1.5V
F3-10600CL8D-4GBHK(XMP)
F3-10666CL8D-4GBECO(XMP) 4GB(2 x 2GB) DS
F3-10666CL7T-6GBPK(XMP)
F3-10666CL7D-8GBRH(XMP)
F3-10666CL9D-8GBRL
GET316GB1333C9QC
6GB(3 x 2GB) DS
8GB(2 x 4GB) DS
8GB(2 x 4GB) DS
16GB(4x 4GB) DS
2GB(2 x 1GB) DS
9-9-9-24 1.5V
9-9-9-24 1.5V
GEIL
GV32GB1333C9DC
9-9-9-24 1.5V
•
•
•
•
•
•
1.3V(low
9-9-9-24
GEIL
GG34GB1333C9DC
GV34GB1333C9DC
HMT112U6TFR8A-H9
HMT325U6BFR8C-H9
HMT125U6TFR8A-H9
4GB(2 x 2GB) DS GEIL
4GB(2 x 2GB) DS
GL1L128M88BA12N
-
•
•
•
•
•
voltage)
GEIL
-
9-9-9-24 1.5V
1.35V(low
voltage)
Hynix
HYNIX
Hynix
1GB
2GB
2GB
SS HYNIX
SS HYNIX
DS HYNIX
DS HYNIX
H5TC1G83TFRH9A
H5TQ2G83BFRH9C
H5TC1G83TFRH9A
H5TQ2G83BFRH9C
-
-
-
-
1.35V(low
voltage)
HYNIX
HMT351U6BFR8C-H9
FLFD45F-B8KL9 NAES
FLFE85F-C8KF9 CAES
FLFE85F-C8KM9 NAES
FLFE85F-B8KL9 NEES
FLFF65F-C8KM9 NEES
KVR1333D3N9/1G
4GB
1GB
2GB
2GB
2GB
4GB
1GB
2GB
-
-
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
KINGMAX
KINGMAX
KINGMAX
KINGMAX
KINGMAX
Kingston
Kingston
Kingston
Kingston
Kingston
Kingston
Kingston
Kingston
Kingston
Micron
SS KINGMAX KKB8FNWBFGNX-27A
SS KINGMAX KFC8FMFXF-DXX-15A
SS KINGMAX KFC8FNMXF-BXX-15A
DS KINGMAX KKB8FNWBFGNX-26A
DS KINGMAX KFC8FNMXF-BXX-15A
-
-
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
-
-
-
-
-
-
-
-
SS ELPIDA
SS HYNIX
DS ELPIDA
DS KTC
J1108BDBG-DJ-F
H5TQ2G83AFRH9C
J1108BDBG-DJ-F
D1288JPNDPLD9U
J1108BDSE-DJ-F
-
9
9
9
9
9
7
9
9
-
1.5V
KVR1333D3N9/2G
-
KVR1333D3N9/2G(low profile) 2GB
1.5V
KVR1333D3N9/2G
2GB
2GB
1.5V
KVR1333D3N9/2G
DS ELPIDA
1.5V
KHX1333C7D3K2/4GX(XMP)
4GB(2 x 2GB) DS
-
-
1.65V
KHX1333C9D3UK2/4GX(XMP) 4GB(2 x 2GB) DS
-
XMP 1.25V
KVR1333D3N9/4G(low profile) 4GB
DS HYNIX
DS Hynix
H5TQ2G83AFRH9C
H5TQ2G83AFR
1.5V
KVR1333D3N9/4G
4GB
1GB
1GB
2GB
2GB
4GB
-
-
-
-
-
-
MT4JTF12864AZ-1G4D1
MT8JTF12864AZ-1G4F1
MT8JTF25664AZ-1G4D1
MT16JTF25664AZ-1G4F1
MT16JTF51264AZ-1G4D1
OCZ3G1333LV3GK
SS MICRON D9LGQ
-
Micron
SS Micron
9FF22D9KPT
9
-
Micron
SS MICRON D9LGK
Micron
DS Micron
9KF27D9KPT
9
-
•
•
•
•
•
•
•
•
•
Micron
DS MICRON D9LGK
OCZ
3GB(3 x 1GB) DS
4GB(2 x 2GB) DS
4GB(2 x 2GB) DS
4GB(2 x 2GB) DS
4GB(2 x 2GB) DS
4GB(2 x 2GB) DS
6GB(3 x 2GB) DS
-
-
-
-
-
-
-
-
-
-
-
-
-
-
9-9-9-20 1.65V
9-9-9-20 1.7V
9-9-9-20 1.7V
9-9-9-20 1.65V
7-7-7-20 1.65V
7-7-7-20 1.75V
9-9-9-20 1.65V
OCZ
OCZ3F13334GK
OCZ
OCZ3G13334GK
OCZ
OCZ3G1333LV4GK
OCZ
OCZ3P1333LV4GK
OCZ
OCZ3X13334GK(XMP)
OCZ3G1333LV6GK
OCZ
OCZ
OCZ3P1333LV6GK
6GB(3 x 2GB) DS
-
-
7-7-7-20 1.65V
•
•
(continued on the next page)
1-20
ASUS P8H61 R2.0 Series
DDR3-1333 MHz capability
DIMM socket support
(Optional)
SS/ Chip
DS Brand
Vendors
Part No.
Size
Chip NO.
Timing Voltage
1 DIMM
2 DIMMs
OCZ
OCZ
OCZ
PSC
PSC
PSC
PSC
OCZ3X1333LV6GK(XMP) 6GB(3 x 2GB) DS
OCZ3G1333LV8GK 8GB(2x 4GB) DS
OCZ3RPR1333C9LV8GK 8GB(2x 4GB) DS
-
-
-
-
8-8-8-20 1.60V
9-9-9-20 1.65V
9-9-9-20 1.65V
8-8-8-24 1.5V
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
-
-
AL7F8G73D-DG1
AL7F8G73F-DJ2
AL8F8G73D-DG1
AL8F8G73F-DJ2
1GB
1GB
2GB
2GB
1GB
2GB
4GB
1GB
2GB
4GB
SS PSC
SS PSC
DS PSC
DS PSC
A3P1GF3DGF
A3P1GF3FGF
A3P1GF3DGF
A3P1GF3FGF
-
-
8-8-8-24 1.5V
-
-
-
-
-
-
-
-
SAMSUNG M378B2873FHS-CH9
SAMSUNG M378B5673FH0-CH9
SAMSUNG M378B5273CH0-CH9
Super Talent W1333UA1GH
SS Samsung K4B1G0846F
DS Samsung K4B1G0846F
DS Samsung K4B2G0846C
-
-
-
SS HYNIX
H5TQ1G83TFR
9
9
-
Super Talent W1333UB2GS
DS Samsung K4B1G0846F
DS Samsung K4B2G0846C
Super Talent W1333UB4GS
Super Talent W1333UX6GM
6GB(3x 2GB) DS Micron
0BF27D9KPT
9-9-9-24 1.5V
Elixir
Elixir
Elixir
Elixir
M2F2G64CB88B7N-CG
M2Y2G64CB8HA9N-CG
M2Y2G64CB8HC9N-CG
M2F4G64CB8HB5N-CG
2GB
2GB
2GB
4GB
2GB
DS Elixir
DS
N2CB2G808N-CG
-
-
-
-
-
-
-
-
7-7-7-20
DS Elixir
DS Elixir
-
-
-
-
N2CB2G808N-CG
KINGSHARE KSRPCD313332G
DS PATRIOT PM128M8D385-15
SEC 904 HCH9
DS Samsung
Kingtiger
2GB DIMM PC3-10666
2GB
-
-
•
•
K4B1G0846D
Kingtiger
PATRIOT
PATRIOT
PATRIOT
RAMAXEL
KTG2G1333PG3
PSD31G13332H
PSD31G13332
PSD32G13332H
2GB
1GB
1GB
2GB
DS
DS
-
-
-
-
-
-
-
-
-
•
•
•
•
•
•
•
•
•
•
-
9
-
DS Patriot
DS
PM64M8D38U-15
-
-
-
RMR1870ED48E8F-1333 2GB
DS ELPIDA
J1108BDBG-DJ-F
-
SILICON
POWER
SP001GBLTU133S01
SP001GBLTU133S02
SP002GBLTU133S02
1GB
1GB
2GB
SS NANYA
NT5CB128M8AN-CG
N2CB1680AN-C6
N2CB1680AN-C6
9
9
9
-
-
-
•
•
•
•
•
•
SILICON
POWER
SS elixir
DS elixir
SILICON
POWER
TAKEMS
TAKEMS
TAKEMS
TAKEMS
TAKEMS
UMAX
TMS1GB364D081-107EY 1GB
TMS1GB364D081-138EY 1GB
TMS2GB364D081-107EY 2GB
TMS2GB364D081-138EY 2GB
TMS2GB364D082-138EW 2GB
SS
SS
DS
DS
DS
-
-
-
-
-
-
7-7-7-20 1.5V
8-8-8-24 1.5V
7-7-7-20 1.5V
8-8-8-24 1.5V
8-8-8-24 1.5V
•
•
•
•
•
•
•
•
•
•
•
•
-
-
-
-
E41302GP0-73BDB
3WVS31333-2G-CNR
2GB
2GB
DS UMAX
DS AMPO
U2S24D30TP-13
-
-
-
-
WINTEC
AM3420803-13H
•
•
Chapter 1: Product introduction
1-21
DDR3-1066 MHz capability
DIMM socket
support (Optional)
SS/
DS
Vendors
Part No.
Size
Chip Brand Chip NO.
Timing Voltage
1 DIMM 2 DIMMs
Crucial
Crucial
CT12864BA1067.8FF
CT25664BA1067.16FF
1GB
2GB
SS Micron
DS Micron
9GF22D9KPT
9HF22D9KPT
7
7
-
-
•
•
•
•
1.35V(low
voltage)
ELPIDA
ELPIDA
ELPIDA
EBJ10UE8EDF0-AE-F
EBJ11UD8BAFA-AE-E
EBJ21UE8EDF0-AE-F
1GB
1GB
2GB
SS ELPIDA
DS Elpida
DS ELPIDA
J1108EDSE-DJ-F
J5308BASE-AC-E
J1108EDSE-DJ-F
-
-
-
•
•
•
•
•
•
-
1.35V(low
voltage)
KINGSTON KVR1066D3N7/1G
KINGSTON KVR1066D3N7/2G
KINGSTON KVR1066D3N7/4G
1GB
2GB
4GB
SS KTC
D1288JPNDPLD9U
J1108BDSE-DJ-F
H5TQ2G83AFR
9GF22D9KPT
9HF22D9KPT
9BF27D9KPV
N2CB1G80CN-BE
-
7
7
7
7
7
1.5V
1.5V
1.5V
-
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
DS ELPIDA
DS Hynix
SS Micron
DS Micron
Micron
Micron
OCZ
MT8JTF12864AZ-1G1F1 1GB
MT16JTF25664AZ-1G1F1 2GB
-
OCZ3G1066LV4GK
4GB(2 x 2GB) DS Micron
7-7-7-20 1.65V
Elixir
M2Y2G64CB8HC5N-BE
M2Y2G64CBHA9N-BE
M2Y2G64CBHC9N-BE
2GB DIMM PC3-8500
2GB
2GB
2GB
2GB
DS Elixir
DS
-
-
-
-
-
Elixir
-
7-7-7-20
Elixir
DS Elixir
DS Hynix
-
-
-
Kingtiger
H5TQ1G83AFP G7C
SS: Single-sided / DS: Double-sided
DIMM support:
•
1 DIMM: Supports one module inserted into either slot as single-channel memory
configuration.
•
2 DIMMs: Supports one pair of modules inserted into both the blue slots as one pair of
dual-channel memory configuration.
1-22
ASUS P8H61 R2.0 Series
1.7.3
Installing a DIMM
Unplug the power supply before adding or removing DIMMs or other system components.
Failure to do so can cause severe damage to both the motherboard and the components.
2
1.
2.
Press the retaining clips outward to
unlock a DIMM socket.
DIMM notch
Align a DIMM on the socket such that
the notch on the DIMM matches the
DIMM slot key on the socket.
1
1
DIMM slot key
Unlocked retaining clip
A DIMM is keyed with a notch so that it fits in only one direction. DO NOT force a DIMM into
a socket in the wrong direction to avoid damaging the DIMM.
3.
Firmly insert the DIMM into the socket
until the retaining clips snap back in place
and the DIMM is properly seated.
3
Locked Retaining Clip
1.7.4
Removing a DIMM
To remove a DIMM:
1. Simultaneously press the retaining clips
outward to unlock the DIMM.
2
Support the DIMM lightly with your
fingers when pressing the retaining
clips. The DIMM might get damaged
when it flips out with extra force.
1
1
DIMM notch
2.
Remove the DIMM from the socket.
Chapter 1: Product introduction
1-23
1.8
Expansion slots
In the future, you may need to install expansion cards. The following sub-sections describe
the slots and the expansion cards that they support.
Unplug the power cord before adding or removing expansion cards. Failure to do so may
cause you physical injury and damage motherboard components.
1.8.1
Installing an expansion card
To install an expansion card:
1.
Before installing the expansion card, read the documentation that came with it and
make the necessary hardware settings for the card.
2.
3.
Remove the system unit cover (if your motherboard is already installed in a chassis).
Remove the bracket opposite the slot that you intend to use. Keep the screw for later
use.
4.
Align the card connector with the slot and press firmly until the card is completely
seated on the slot.
5.
6.
Secure the card to the chassis with the screw you removed earlier.
Replace the system cover.
1.8.2
Configuring an expansion card
After installing the expansion card, configure it by adjusting the software settings.
1.
Turn on the system and change the necessary BIOS settings, if any. See Chapter 2 for
information on BIOS setup.
2.
3.
Assign an IRQ to the card.
Install the software drivers for the expansion card.
When using PCI cards on shared slots, ensure that the drivers support “Share IRQ” or that
the cards do not need IRQ assignments. Otherwise, conflicts will arise between the two PCI
groups, making the system unstable and the card inoperable.
1.8.3
PCI slots
The PCI slots support cards such as a LAN card, SCSI card, USB card, and other cards that
comply with PCI specifications.
1.8.4
PCI Express x1 slots
This motherboard supports PCI Express x1 network cards, SCSI cards, and other cards that
comply with the PCI Express specifications.
1.8.5
PCI Express 3.0/2.0 x16 slot
This motherboard has a PCI Express 3.0/2.0 x16 slot that supports PCI Express 3.0/2.0 x16
graphic cards complying with the PCI Express specifications.
1-24
ASUS P8H61 R2.0 Series
1.9
Jumpers
Clear RTC RAM (3-pin CLRTC)
This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can
clear the CMOS memory of date, time, and system setup parameters by erasing
the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in
CMOS, which include system setup information such as system passwords.
P8H61/USB3 R2.0
CLRTC
1
2
2
3
Normal
Clear RTC
(Default)
P8H61/USB3 R2.0 Clear RTC RAM
To erase the RTC RAM:
1. Turn OFF the computer and unplug the power cord.
2. Move the jumper cap from pins 1-2 (default) to pins 2-3. Keep the cap on pins 2-3
for about 5-10 seconds, then move the cap back to pins 1-2.
3. Plug the power cord and turn ON the computer.
4. Hold down the <Del> key during the boot process and enter BIOS setup to re-enter
data.
Except when clearing the RTC RAM, never remove the cap on CLRTC jumper default
position. Removing the cap will cause system boot failure!
•
•
If the steps above do not help, remove the onboard battery and move the jumper again
to clear the CMOS RTC RAM data. After clearing the CMOS, reinstall the battery.
You do not need to clear the RTC when the system hangs due to overclocking. For
system failure due to overclocking, use the CPU Parameter Recall (C.P.R.) feature. Shut
down and reboot the system, then the BIOS automatically resets parameter settings to
default values.
Chapter 1: Product introduction
1-25
1.10
Connectors
1.10.1
Rear panel connectors
1
2
3
4 5
10
9
8
7
6
1.
2.
3.
PS/2 Mouse port (green). This port is for a PS/2 mouse.
Parallel port. This 25-pin port connects a parallel printer, a scanner, or other devices.
LAN (RJ-45) port. This port allows Gigabit connection to a Local Area Network (LAN)
through a network hub. Refer to the table below for the LAN port LED indications.
LAN port LED indications
Speed
LED
Activity Link
LED
Activity/Link LED
Speed LED
Status
Status
Description
Description
OFF
No link
OFF
10Mbps connection
100Mbps connection
1Gbps connection
ORANGE
BLINKING
Linked
ORANGE
GREEN
Data activity
LAN port
4.
5.
6.
Line In port (light blue). This port connects to the tape, CD, DVD player, or other
audio sources.
Line Out port (lime). This port connects to a headphone or a speaker. In the 4, 6, and
8-channel configurations, the function of this port becomes Front Speaker Out.
Microphone port (pink). This port connects to a microphone.
Refer to the audio configuration table below for the function of the audio ports in 2, 4, 6, or
8-channel configuration.
Audio 2, 4, 6, or 8-channel configuration
Port
Headset 2-channel
4-channel
6-channel
8-channel
Light Blue (Rear panel)
Lime (Rear panel)
Pink (Rear panel)
Lime (Front panel)
Line In
Line Out
Mic In
–
Rear Speaker Out
Rear Speaker Out
Rear Speaker Out
Front Speaker Out
Bass/Center
Front Speaker Out Front Speaker Out
Mic In
–
Bass/Center
–
Side Speaker Out
To configure an 8-channel audio output:
Use a chassis with HD audio module in the front panel to support 8-channel audio output.
1-26
ASUS P8H61 R2.0 Series
7.
8.
USB 2.0 ports 1 and 2. These two 4-pin Universal Serial Bus (USB) ports are for USB
2.0/1.1 devices.
USB 2.0 ports 3 and 4 (P8H61 R2.0 and P8H61 PLUS R2.0 only). These two 4-pin
Universal Serial Bus (USB) ports are for USB 2.0/1.1 devices.
USB 3.0 ports 1 and 2 (P8H61/USB3 R2.0 only). These two 9-pin Universal Serial
Bus (USB) ports are available for connecting USB 3.0/2.0 devices.
•
•
DO NOT connect a keyboard / mouse to any USB 3.0 port when installing Windows®
operating system.
Due to USB 3.0 controller limitation, USB 3.0 devices can only be used under Windows®
OS environment and after the USB 3.0 driver installation.
•
•
USB 3.0 devices can only be used as data storage only.
We strongly recommend that you connect USB 3.0 devices to USB 3.0 ports for faster
and better performance for your USB 3.0 devices.
9.
Serial port. This 9-pin COM1 port is for pointing devices or other serial devices.
10. PS/2 Keyboard port (purple). This port is for a PS/2 keyboard.
1.10.2
Internal connectors
1.
Front panel audio connector (10-1 pin AAFP)
This connector is for a chassis-mounted front panel audio I/O module that supports
either HD Audio or legacy AC`97 audio standard. Connect one end of the front panel
audio I/O module cable to this connector.
AAFP
PIN 1
P8H61/USB3 R2.0
HD-audio-compliant
pin definition
Legacy AC’97
compliant definition
P8H61/USB3 R2.0 Front panel audio connector
•
We recommend that you connect a high-definition front panel audio module to this
connector to avail of the motherboard’s high-definition audio capability.
•
If you want to connect a high-definition front panel audio module to this connector, set
the Front Panel Type item in the BIOS setup to [HD]. If you want to connect an AC'97
front panel audio module to this connector, set the item to [AC97]. By default, this
connector is set to [HD]. See section 2.5.6 Onboard Devices Configuration for details.
Chapter 1: Product introduction
1-27
2.
ATX power connectors (24-pin EATXPWR, 4-pin ATX12V)
These connectors are for ATX power supply plugs. The power supply plugs are
designed to fit these connectors in only one orientation. Find the proper orientation and
push down firmly until the connectors completely fit.
ATX12V
EATXPWR
+3 Volts
GND
+12 Volts
+12 Volts
+5V Standby
Power OK
GND
+5 Volts
+5 Volts
+5 Volts
-5 Volts
GND
P8H61/USB3 R2.0
PIN 1
+5 Volts
GND
GND
GND
+5 Volts
GND
PSON#
GND
+3 Volts
+3 Volts
-12 Volts
+3 Volts
PIN 1
P8H61/USB3 R2.0 ATX power connectors
•
For a fully configured system, we recommend that you use a power supply unit (PSU)
that complies with ATX 12 V Specification 2.0 (or later version) and provides a minimum
power of 350 W.
•
DO NOT forget to connect the 4-pin ATX +12V power plug. Otherwise, the system will
not boot up.
•
We recommend that you use a PSU with higher power output when configuring a
system with more power-consuming devices. The system may become unstable or may
not boot up if the power is inadequate.
•
If you are uncertain about the minimum power supply requirement for your system,
com/PowerSupplyCalculator/PSCalculator.aspx?SLanguage=en-us for details.
1-28
ASUS P8H61 R2.0 Series
3.
CPU and chassis fan connectors (4-pin CPU_FAN, 3-pin CHA_FAN)
Connect the fan cables to the fan connectors on the motherboard, ensuring that the
black wire of each cable matches the ground pin of the connector.
CPU_FAN
CHA_FAN
P8H61/USB3 R2.0
P8H61/USB3 R2.0 fan connectors
Do not forget to connect the fan cables to the fan connectors. Insufficient air flow inside the
system may damage the motherboard components. These are not jumpers! Do not place
jumper caps on the fan connectors!
•
•
The CPU_FAN connector supports a CPU fan of maximum 1A (12 W) fan power.
Only the 4-pin CPU fan supports the ASUS Fan Xpert feature.
4.
Digital audio connector (4-1 pin SPDIF_OUT)
This connector is for an additional Sony/Philips Digital Interface (S/PDIF) port. Connect
the S/PDIF Out module cable to this connector, then install the module to a slot
opening at the back of the system chassis.
P8H61/USB3 R2.0
SPDIF_OUT
P8H61/USB3 R2.0 Digital audio connector
The S/PDIF module is purchased separately.
Chapter 1: Product introduction
1-29
5.
Intel® H61 Serial ATA 3.0Gb/s connectors (7-pin SATA3G_1~4)
These connectors connect to Serial ATA 3.0 Gb/s hard disk drives and optical drives via
Serial ATA 3.0 Gb/s signal cables.
SATA3G_4
SATA3G_2
SATA3G_3
SATA3G_1
P8H61/USB3 R2.0
P8H61/USB3 R2.0 Intel® SATA 3.0Gb/s connectors
•
•
•
•
•
You must install Windows® XP Service Pack 3 or later version before using Serial ATA
hard disk drives.
Due to H61 Chipset limitation, AHCI Mode only works on Windows® Vista / Windows® 7.
Please use IDE Mode on Windows® XP.
[IDE] is the default SATA type. Under Windows® XP, there is no need to change the
SATA type.
To configure the SATA type in BIOS, click Advanced Mode > Advanced tab > SATA
Configuration > SATA Mode Selection.
When using hot-plug and NCQ on Windows® Vista / Windows® 7, set the SATA Mode
Selection item in the BIOS to [AHCI]. See section 2.5.3 SATA Configuration for details.
1-30
ASUS P8H61 R2.0 Series
6.
USB 2.0 connectors (10-1 pin USB56, USB78, USB910)
These connectors are for USB 2.0 ports. Connect the USB module cable to any of
these connectors, then install the module to a slot opening at the back of the system
chassis. These USB connectors comply with USB 2.0 specification that supports up to
480 Mbps connection speed.
USB56
USB78
USB910
P8H61/USB3 R2.0
PIN 1
PIN 1
PIN 1
P8H61/USB3 R2.0 USB2.0 connectors
Never connect a 1394 cable to the USB connectors. Doing so will damage the motherboard!
The USB module cable is purchased separately.
Chapter 1: Product introduction
1-31
7.
System panel connector (20-8 pin F_PANEL)
This connector supports several chassis-mounted functions.
PLED
SPEAKER
PANEL
PIN 1
P8H61/USB3 R2.0
IDE_LED
PWRSW RESET
* Requires an ATX power supply
P8H61/USB3 R2.0 System panel connector
•
System power LED (2-pin PLED)
This 2-pin connector is for the system power LED. Connect the chassis power LED
cable to this connector. The system power LED lights up when you turn on the system
power, and blinks when the system is in sleep mode.
•
•
Hard disk drive activity LED (2-pin IDE_LED)
This 2-pin connector is for the HDD Activity LED. Connect the HDD Activity LED cable
to this connector. The IDE LED lights up or flashes when data is read from or written to
the HDD.
System warning speaker (4-pin SPEAKER)
This 4-pin connector is for the chassis-mounted system warning speaker. The speaker
allows you to hear system beeps and warnings.
•
•
ATX power button/soft-off button (2-pin PWRSW)
This 2-pin connector is for the system power button.
Reset button (2-pin RESET)
This 2-pin connector is for the chassis-mounted reset button for system reboot without
turning off the system power.
1-32
ASUS P8H61 R2.0 Series
1.11
Software support
1.11.1
Installing an operating system
This motherboard supports Windows® XP / Vista / 7 Operating Systems (OS). Always install
the latest OS version and corresponding updates to maximize the features of your hardware.
•
•
Motherboard settings and hardware options vary. Refer to your OS documentation for
detailed information.
Ensure that you install Windows® XP Service Pack 3 or later versions / Windows® Vista
Service Pack 1 or later versions before installing the drivers for better compatibility and
system stability.
1.11.2
Support DVD information
The Support DVD that comes with the motherboard package contains the drivers, software
applications, and utilities that you can install to avail all motherboard features.
The contents of the Support DVD are subject to change at any time without notice. Visit the
To run the Support DVD
Place the Support DVD to the optical drive. If Autorun is enabled in your computer, the DVD
automatically displays the Specials screen. Click Drivers, Utilities, Manual, Contact, and
Specials tabs to display their respective menus.
The following screen is for reference only.
Click an icon to
display Support DVD/
motherboard information
Click an item to install
If Autorun is NOT enabled in your computer, browse the contents of the Support DVD to
locate the file ASSETUP.EXE from the BIN folder. Double-click the ASSETUP.EXE to run
the DVD.
Chapter 1: Product introduction
1-33
1-34
ASUS P8H61 R2.0 Series
Chapter 2
BIOS information
2.1
Managing and updating your BIOS
Save a copy of the original motherboard BIOS file to a USB flash disk in case you need to
restore the BIOS in the future. Copy the original motherboard BIOS using the ASUS Update
utility.
2.1.1
ASUS Update utility
The ASUS Update is a utility that allows you to manage, save, and update the motherboard
BIOS in Windows® environment.
•
•
ASUS Update requires an Internet connection either through a network or an Internet
Service Provider (ISP).
This utility is available in the support DVD that comes with the motherboard package.
Installing ASUS Update
To install ASUS Update:
1.
2.
3.
Place the support DVD in the optical drive. The Specials menu appears.
Click the Utilities tab, then click AI Suite II.
Follow the onscreen instructions to complete the installation.
Quit all Windows® applications before you update the BIOS using this utility.
Updating the BIOS
To update the BIOS:
1.
From the Windows® desktop, click Start > Programs > ASUS > AI Suite II > AI Suite II X.XX.XX to
launch the AI Suite II utility. The AI Suite II Quick Bar appears.
2.
Click Update button from the Quick Bar, and then click ASUS Update from the popup menu. The
ASUS Update main screen appears. From the list, select either of the following methods:
Updating from the Internet
a.
b.
c.
Select Update BIOS from the Internet, then click Next.
Select the ASUS FTP site nearest you to avoid network traffic, then click Next.
From the FTP site, select the BIOS version that you wish to download then click Next.
Chapter 2: BIOS information
2-1
The ASUS Update utility is capable of updating itself through the Internet. Always update
the utility to avail all its features.
Updating from a BIOS file
a.
Select Update BIOS from file, then click Next.
b.
Locate the BIOS file from the Open window, then click Open.
3.
Follow the onscreen instructions to complete the updating process.
2.1.2
ASUS EZ Flash 2
The ASUS EZ Flash 2 feature allows you to update the BIOS without using an OS-based
utility.
Before you start using this utility, download the latest BIOS file from the ASUS website at
To update the BIOS using EZ Flash 2:
1.
Insert the USB flash disk that contains the latest BIOS file to the USB port.
2.
Enter the Advanced Mode of the BIOS setup program. Go to the Tool menu to select ASUS EZ
Flash 2 Utility and press <Enter> to enable it.
Exit
ASUS EZ Flash 2 Utility V01.04
Flash Info
MODEL: P8H61/USB3 R2.0
VER: 0206
DATE: 02/10/2012
File Path: fs0:\
Drive Info
fs0:\
Folder Info
02/10/2012 10:23p
8388608
H61U3R2.CAP
File Info
MODEL:
VER:
DATE
Help Info
[Enter] Select or Load
[Tab] Switch
[Up/Down/PageUp/PageDown/Home/End] Move
[Esc] Exit
2-2
ASUS P8H61 R2.0 Series
3.
Press <Tab> to switch to the Drive field.
4.
Press the Up/Down arrow keys to find the USB flash disk that contains the latest BIOS, and then
press <Enter>.
5.
Press <Tab> to switch to the Folder Info field.
6.
Press the Up/Down arrow keys to find the BIOS file, and then press <Enter> to perform the BIOS
update process. Reboot the system when the update process is done.
•
This function supports USB flash disks with FAT 32/16 format and single partition only.
•
DO NOT shut down or reset the system while updating the BIOS to prevent system boot
failure!
2.1.3
ASUS CrashFree BIOS 3 utility
The ASUS CrashFree BIOS 3 is an auto recovery tool that allows you to restore the BIOS file
when it fails or gets corrupted during the updating process. You can restore a corrupted BIOS
file using the motherboard support DVD or a USB flash drive that contains the updated BIOS
file.
•
•
Before using this utility, rename the BIOS file in the removable device into
P8H61R2.CAP (for P8H61 R2.0), P8H61PR2.CAP (for P8H61 PLUS R2.0), or
H61U3R2.CAP (for P8H61/USB3 R2.0).
The BIOS file in the support DVD may not be the latest version. Download the latest
BIOS file from the ASUS website at www.asus.com.
Recovering the BIOS
To recover the BIOS:
1.
Turn on the system.
2.
Insert the support DVD to the optical drive or the USB flash drive that contains the BIOS file to the
USB port.
3.
The utility automatically checks the devices for the BIOS file. When found, the utility reads the BIOS
file and enters ASUS EZ Flash 2 utility automatically.
4.
The system requires you to enter BIOS Setup to recover BIOS setting. To ensure system
compatibility and stability, we recommend that you press <F5> to load default BIOS values.
DO NOT shut down or reset the system while updating the BIOS! Doing so can cause
system boot failure!
Chapter 2: BIOS information
2-3
2.1.4
ASUS BIOS Updater
The ASUS BIOS Updater allows you to update BIOS in DOS environment. This utility also
allows you to copy the current BIOS file that you can use as a backup when the BIOS fails or
gets corrupted during the updating process.
The succeeding utility screens are for reference only. The actual utility screen displays may
not be same as shown.
Before updating BIOS
1.
Prepare the motherboard support DVD and a USB flash drive in FAT32/16 format and single
partition.
2.
Download the latest BIOS file and BIOS Updater from the ASUS website at
http://support.asus.com and save them on the USB flash drive.
NTFS is not supported under DOS environment. Do not save the BIOS file and BIOS
Updater to a hard disk drive or USB flash drive in NTFS format.
3.
Turn off the computer and disconnect all SATA hard disk drives (optional).
Booting the system in DOS environment
1.
Insert the USB flash drive with the latest BIOS file and BIOS Updater to the USB port.
2.
Boot your computer. When the ASUS Logo appears, press <F8> to show the BIOS Boot Device
Select Menu. Insert the support DVD into the optical drive and select the optical drive as the boot
device.
Please select boot device:
SATA: XXXXXXXXXXXXXXXX
USB XXXXXXXXXXXXXXXXX
UEFI: XXXXXXXXXXXXXXXX
Enter Setup
↑ and ↓ to move selection
ENTER to select boot device
ESC to boot using defaults
3.
4.
When the Make Disk menu appears, select the FreeDOS command prompt item by pressing the
item number.
At the FreeDOS prompt, type d:and press <Enter> to switch the disk from
Drive C (optical drive) to Drive D (USB flash drive).
Welcome to FreeDOS (http://www.freedos.org)!
C:\>d:
D:\>
2-4
ASUS P8H61 R2.0 Series
Updating the BIOS file
To update the BIOS file using BIOS Updater
1.
At the FreeDOS prompt, type bupdater /pc /gand press <Enter>.
D:\>bupdater /pc /g
2.
The BIOS Updater screen appears as below.
ASUSTek BIOS Updater for DOS V1.30
Current ROM
BOARD: P8H61/USB3 R2.0
VER: 0206
Update ROM
BOARD: Unknown
VER: Unknown
DATE: 02/10/2012
DATE: Unknown
PATH: A:\
A:
H61U3R2.CAP
8388608 2012-02-10 17:30:48
Note
[Enter] Select or Load
[Up/Down/Home/End] Move
[Tab] Switch
[Esc] Exit
[V] Drive Info
3.
Press <Tab> to switch between screen fields and use the <Up/Down/Home/End> keys to select
the BIOS file and press <Enter>. BIOS Updater checks the selected BIOS file and prompts you to
confirm BIOS update.
Are you sure to update BIOS?
Yes
No
4.
Select Yes and press <Enter>. When BIOS update is done, press <ESC> to exit BIOS Updater.
Restart your computer.
DO NOT shut down or reset the system while updating the BIOS to prevent system boot
failure!
•
•
For BIOS Updater version 1.04 or later, the utility automatically exits to the DOS prompt
after updating BIOS.
Ensure to load the BIOS default settings to ensure system compatibility and stability.
Select the Load Optimized Defaults item under the Exit menu. Refer to section 2.9
Exit menu for details.
•
Ensure to connect all SATA hard disk drives after updating the BIOS file if you have
disconnected them.
Chapter 2: BIOS information
2-5
2.2
BIOS setup program
Use the BIOS Setup program to update the BIOS or configure its parameters. The BIOS
screens include navigation keys and brief online help to guide you in using the BIOS Setup
program.
Entering BIOS Setup at startup
To enter BIOS Setup at startup:
•
Press <Delete> during the Power-On Self Test (POST). If you do not press <Delete>,
POST continues with its routines.
Entering BIOS Setup after POST
To enter BIOS Setup after POST:
•
•
•
Press <Ctrl>+<Alt>+<Del> simultaneously.
Press the reset button on the system chassis.
Press the power button to turn the system off then back on. Do this option only if you
failed to enter BIOS Setup using the first two options.
Using the power button, reset button, or the <Ctrl>+<Alt>+<Del> keys to force reset from
a running operating system can cause damage to your data or system. We recommend to
always shut down the system properly from the operating system.
•
•
•
•
The BIOS setup screens shown in this section are for reference purposes only, and may
not exactly match what you see on your screen.
motherboard.
Ensure that a USB mouse is connected to your motherboard if you want to use the
mouse to control the BIOS setup program.
If the system becomes unstable after changing any BIOS setting, load the default
settings to ensure system compatibility and stability. Select the Load Optimized
Defaults item under the Exit menu. See section 2.9 Exit Menu for details.
•
If the system fails to boot after changing any BIOS setting, try to clear the CMOS and
reset the motherboard to the default value. See section 1.9 Jumpers for information on
how to erase the RTC RAM.
BIOS menu screen
The BIOS setup program can be used under two modes: EZ Mode and Advanced Mode.
You can change modes from the Exit menu or from the Exit/Advanced Mode button in the
EZ Mode/Advanced Mode screen.
2-6
ASUS P8H61 R2.0 Series
EZ Mode
By default, the EZ Mode screen appears when you enter the BIOS setup program. The EZ
Mode provides you an overview of the basic system information, and allows you to select
the display language, system performance mode and boot device priority. To access the
Advanced Mode, click Exit/Advanced Mode or press Esc, then select Advanced Mode or
press F7 hot key for the advanced BIOS settings.
The default screen for entering the BIOS setup program can be changed. Refer to the
Setup Mode item in section 2.7 Boot menu for details.
Selects the display language of
the BIOS setup program
Displays the CPU/motherboard temperature,
Exits the BIOS setup program without saving
CPU/5V/3.3V/12V voltage output,
CPU/chassis fan speed
the changes, saves the changes and resets
the system, or enters the Advanced Mode
Exit/Advanced Mode
UEFI BIOS Utility - EZ Mode
P8H61/USB3 R2.0
BIOS Version : 0206
English
Build Date : 02/10/2012
CPU Type : Intel(R) Core(TM) i5-2500 CPU 0 @ 3.30GHz Speed : 3300 MHz
Total Memory : 1024 MB (DDR3 1333MHz)
Friday [10/08/2010]
Temperature
Voltage
CPU
Fan Speed
CPU_FAN 3325RPM CHA_FAN
CPU
MB
+113.0ºF/+45.0ºC
+75.2ºF/+40.0ºC
1.248V
3.344V
5V
5.160V
N/A
3.3V
12V
12.248V
System Performance
Quiet
Performance
Boot Priority
Energy Saving
Normal
Use the mouse to drag or keyboard to navigate to decide the boot priority.
Shortcut (F3) Advanced Mode(F7)
Boot Menu(F8)
Default(F5)
Power Saving mode
Loads optimized default
ASUS Optimal mode
Selects the Advanced
mode functions
Normal mode
Selects the boot device priority
Selects the boot
device priority
Displays the system properties of the
selected mode on the right hand side
Displays the Advanced mode menus
•
•
The boot device options vary depending on the devices you installed to the system.
The Boot Menu(F8) button is available only when the boot device is installed to the
system.
Chapter 2: BIOS information
2-7
Advanced Mode
The Advanced Mode provides advanced options for experienced end-users to configure
the BIOS settings. The figure below shows an example of the Advanced Mode. Refer to the
following sections for the detailed configurations.
To access the EZ Mode, click Exit, then select ASUS EZ Mode.
Back button
UEFI BIOS Utility - Advanced Mode
Menu items
Menu bar
Configuration fields
General help
Exit
Main
Back
Ai Tweaker
Advanced
Monitor
Boot
Tool
Advanced\ Onboard Devices Configuration
>
Enabled/Disabled Realtek Controller.
HD Audio Controller
Front Panel Type
SPDIF Out Type
Enabled
HD
SPDIF
Realtek LAN Controller
Realtek PXE OPROM
Enabled
Disabled
Realtek LAN Controller
Disabled
Enabled
Asmedia USB 3.0 Controller
Enabled
Disabled
Asmedia USB 3.0 Battery Charging Support
→←: Select Screen
↑↓: Select Item
Enter: Select
>
>
Serial Port Configuration
Parallel Port Configuration
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Shortcut
F5: Optimized Defaults
F10: Save ESC: Exit
F12: Print Screen
Version 2.10.1208. Copyright (C) 2012 American Megatrends, Inc.
Submenu item
Pop-up window
Scroll bar
Navigation keys
Menu bar
The menu bar on top of the screen has the following main items:
Main
For changing the basic system configuration
For changing the overclocking settings
For changing the advanced system settings
Ai Tweaker
Advanced
Monitor
Boot
For displaying the system temperature, power status, and changing the fan settings
For changing the system boot configuration
Tool
For configuring options for special functions
Exit
For selecting the exit options and loading default settings
2-8
ASUS P8H61 R2.0 Series
Menu items
The highlighted item on the menu bar displays the specific items for that menu. For example,
selecting Main shows the Main menu items.
The other items (Ai Tweaker, Advanced, Monitor, Boot, Tool, and Exit) on the menu bar have
their respective menu items.
Back button
This button appears when entering a submenu. Press <Esc> or use the USB mouse to click
this button to return to the previous menu screen.
Submenu items
A greater than sign (>) before each item on any menu screen means that the item has a
submenu. To display the submenu, select the item and press <Enter>.
Pop-up window
Select a menu item and press <Enter> to display a pop-up window with the configuration
options for that item.
Scroll bar
A scroll bar appears on the right side of a menu screen when there are items that do not fit on
the screen. Press the Up/Down arrow keys or <Page Up> / <Page Down> keys to display the
other items on the screen.
Navigation keys
At the bottom right corner of the menu screen are the navigation keys for the BIOS setup
program. Use the navigation keys to select items in the menu and change the settings.
General help
At the top right corner of the menu screen is a brief description of the selected item.
Configuration fields
These fields show the values for the menu items. If an item is user-configurable, you can
change the value of the field opposite the item. You cannot select an item that is not
user-configurable.
A configurable field is highlighted when selected. To change the value of a field, select it and
press <Enter> to display a list of options.
Chapter 2: BIOS information
2-9
2.3
Main menu
The Main menu screen appears when you enter the Advanced Mode of the BIOS Setup
program. The Main menu provides you an overview of the basic system information, and
allows you to set the system date, time, language, and security settings.
Exit
UEFI BIOS Utility - Advanced Mode
Main
Ai Tweaker
Advanced
Monitor
Boot
Tool
BIOS Information
BIOS Version
Choose the system default language
0206 x64
02/10/2012
8.0.0.1351
B3
Build Date
ME Version
South Bridge Stepping
CPU Information
Intel(R) Core(TM) i5-2500 CPU @ 3.30GHz
Speed
3300 MHz
Memory Information
Total Memory
1024 MB (DDR3)
Memory Frequency
1333 MHz
System Language
English
System Date
System Time
Access Level
[Monday 12/27/2010]
[16:46:15]
Administrator
>
Security
2.3.1
System Language [English]
Allows you to choose the BIOS language version from the options. Configuration options:
[English]
[Español] [Русский]
2.3.2
System Date [Day xx/xx/xxxx]
Allows you to set the system date.
2.3.3
System Time [xx:xx:xx]
Allows you to set the system time.
2.3.4
Security
The Security menu items allow you to change the system security settings.
•
•
If you have forgotten your BIOS password, erase the CMOS Real Time Clock (RTC)
RAM to clear the BIOS password. See section 1.9 Jumpers for information on how to
erase the RTC RAM.
The Administrator or User Password items on top of the screen show the default Not
Installed. After you set a password, these items show Installed.
2-10
ASUS P8H61 R2.0 Series
Administrator Password
If you have set an administrator password, we recommend that you enter the administrator
password for accessing the system. Otherwise, you might be able to see or change only
selected fields in the BIOS setup program.
To set an administrator password:
1.
2.
3.
Select the Administrator Password item and press <Enter>.
From the Create New Password box, key in a password, then press <Enter>.
Confirm the password when prompted.
To change an administrator password:
1.
2.
3.
4.
Select the Administrator Password item and press <Enter>.
From the Enter Current Password box, key in the current password, then press <Enter>.
From the Create New Password box, key in a new password, then press <Enter>.
Confirm the password when prompted.
To clear the administrator password, follow the same steps as in changing an administrator
password, but press <Enter> when prompted to create/confirm the password. After you clear
the password, the Administrator Password item on top of the screen shows Not Installed.
User Password
If you have set a user password, you must enter the user password for accessing the system.
The User Password item on top of the screen shows the default Not Installed. After you set
a password, this item shows Installed.
To set a user password:
1.
2.
3.
Select the User Password item and press <Enter>.
From the Create New Password box, key in a password, then press <Enter>.
Confirm the password when prompted.
To change a user password:
1.
2.
3.
4.
Select the User Password item and press <Enter>.
From the Enter Current Password box, key in the current password, then press <Enter>.
From the Create New Password box, key in a new password, then press <Enter>.
Confirm the password when prompted.
To clear the user password, follow the same steps as in changing a user password, but press
<Enter> when prompted to create/confirm the password. After you clear the password, the
User Password item on top of the screen shows Not Installed.
Chapter 2: BIOS information
2-11
2.4
Ai Tweaker menu
The Ai Tweaker menu items allow you to configure overclocking-related items.
Be cautious when changing the settings of the Ai Tweaker menu items. Incorrect field
values can cause the system to malfunction.
The configuration options for this section vary depending on the CPU and DIMM model you
installed on the motherboard.
Exit
UEFI BIOS Utility - Advanced Mode
Main
Ai Tweaker
Advanced
Monitor
Boot
Tool
[X.M.P.] When XMP is enabled BLCK
frequency, CPU ratio and memory
parameters will be auto optimized.
Target DRAM Speed : 1333MHz
Ai Overclock Tuner
Auto
Memory Frequency
Auto
EPU Power Saving Mode
Disabled
>
>
>
>
OC Tuner
DRAM Timing Control
CPU Power Management
DIGI+ VRM
→←: Select Screen
↑↓: Select Item
Enter: Select
CPU Voltage
0.904V
Offset Mode
+
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Shortcut
CPU Offset Mode Sign
CPU Offset Voltage
DRAM Voltage
Auto
Auto
F5: Optimized Defaults
F10: Save ESC: Exit
F12: Print Screen
1.500V
Version 2.10.1208. Copyright (C) 2012 American Megatrends, Inc.
Scroll down to display the following items:
→←: Select Screen
↑↓: Select Item
Enter: Select
VCCSA Voltage
PCH Voltage
0.925V
1.050V
Auto
Auto
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Shortcut
CPU PLL Voltage
CPU Spread Spectrum
Auto
Auto
F5: Optimized Defaults
F10: Save ESC: Exit
F12: Print Screen
Version 2.10.1208. Copyright (C) 2012 American Megatrends, Inc.
2-12
ASUS P8H61 R2.0 Series
2.4.1
Ai Overclock Tuner [Auto]
Allows you to select the CPU overclocking options to achieve the desired CPU internal
frequency. Select any of these preset overclocking configuration options:
[Auto]
Loads the optimal settings for the system.
[Manual]
[X.M.P.]
Allows you to individually set overclocking parameters.
If you install memory modules supporting the eXtreme Memory Profile
(X.M.P.) Technology, choose this item to set the profiles supported by your
memory modules for optimizing the system performance.
The item X.M.P. appears only when you install a DIMM with X.M.P. support.
X.M.P. DDR3-xxxx x-x-x-x-xxV [Profile #1]
This item appears only when you set the Ai Overclocking Tuner item to [X.M.P.] and allows
you to select the X.M.P. mode supported by your memory module. Configuration options:
[Profile #1] [ Profile #2]
The configuration options vary with the DIMM you installed on the system.
BCLK/PCIE Frequency [XXX]
Appears when you set the Ai Overclock Tuner item to [Manual] or [X.M.P.] and allows you
to adjust the CPU and VGA frequency to enhance the system performance. Use the <+> and
<-> keys to adjust the value. You can also key in the desired value using the numeric keypad.
The values range from 80MHz to 300MHz.
2.4.2
Memory Frequency [Auto]
Allows you to set the memory operating frequency.
Configuration options (Ivy Bridge CPU): [Auto] [DDR3-800MHz] [DDR3-1066MHz] [DDR3-
1333MHz] [DDR3-1400MHz] [DDR3-1600MHz] [DDR3-1800MHz] [DDR3-1866MHz]
[DDR3-2000MHz] [DDR3-2133MHz] [DDR3-2200MHz] [DDR3-2400MHz] [DDR3-2600MHz]
[DDR3-2666MHz] [DDR3-2800MHz]
Configuration options (Sandy Bridge CPU): [Auto] [DDR3-800MHz] [DDR3-1066MHz] [DDR3-
1600MHz] [DDR3-1866MHz] [DDR3-2133MHz] [DDR3-2400MHz]
Selecting a very high memory frequency may cause the system to become unstable! If this
happens, revert to the default setting.
2.4.3
EPU Power Saving Mode [Disabled]
Allows you to enable or disable the EPU power saving function.
Configuration options: [Disabled] [Enabled]
EPU Setting [Auto]
This item appears only when you set the EPU Power Saving Mode item to [Enabled] and
allows you to select the EPU power saving mode. Configuration options: [Auto] [Light Power
Saving Mode] [Medium Power Saving Mode] [Max Power Saving Mode]
Chapter 2: BIOS information
2-13
2.4.4
OC Tuner
OC Tuner automatically overclocks the frequency and voltage of CPU and DRAM for
enhancing the system performance. Press <Enter> and select OK to start automatic
overclocking.
2.4.5
DRAM Timing Control
The sub-items in this menu allow you to set the DRAM timing control features. Use the <+>
and <-> keys to adjust the value. To restore the default setting, type [auto] using the keyboard
and press <Enter>.
Changing the values in this menu may cause the system to become unstable! If this
happens, revert to the default settings.
2.4.6
CPU Power Management
The sub-items in this menu allow you to set the CPU ratio and features.
CPU Ratio [Auto]
Allows you to manually adjust the maximum non-turbo CPU ratio. Use <+> and <-> keys or
the numeric keypad to adjust the value. The valid value ranges vary according to your CPU
model.
Enhanced Intel SpeedStep Technology [Enabled]
Allows you to enable or disable the Enhanced Intel® SpeedStep Technology (EIST).
[Disabled]
[Enabled]
Disables this function.
The operating system dynamically adjusts the processor voltage and
core frequency which may result in decreased average consumption and
decreased average heat production.
Turbo Mode [Enabled]
[Enabled]
Allows processor cores to run faster than marked frequency in specific
conditions.
[Disabled]
Disables this function.
The following three items appear only when you set the Turbo Mode item to [Enabled].
Long Duration Power Limit [Auto]
Allows you to limit the turbo ratio’s long duration power.
Use the <+> and <-> keys to adjust the value.
Long Duration Maintained [Auto]
Allows you to maintain the turbo ratio’s long duration power.
Use the <+> and <-> keys to adjust the value.
Short Duration Power Limit [Auto]
Allows you to limit the turbo ratio’s long duration power.
Use the <+> and <-> keys to adjust the value.
2-14
ASUS P8H61 R2.0 Series
Primary Plane Current Limit [Auto]
Maximum instantaneous current allowed at any given time for CPU cores
Use <+> and <-> key to adjust the value at 0.125A increment. .
Secondary Plane Current Limit [Auto]
Maximum instantaneous current allowed at any given time for Internal Graphics cores.
Use <+> and <-> key to adjust the value at 0.125A increment.
2.4.7
DIGI+ VRM
CPU Load-Line Calibration [Auto]
Load-line is defined by Intel VRM specifications, and affects CPU voltage. The CPU working
voltage will decrease proportionally to CPU loading. Higher value gets a higher voltage, and
a better overclocking performance, but increases the CPU and VRM thermal conditions.
This item allows you to adjust the voltage range from the following percentages to boost the
system performance: 0% (Regular), 25% (Medium), 50% (High), 75% (Ultra High) and 100%
(Extreme). Configuration options: [Auto] [Regular] [Medium] [High] [Ultra High] [Extreme]
The actual performance boost may vary depending on your CPU specification.
CPU Fixed Frequency [xxx]
Allows you to set a fixed CPU frequency. Use the <+> and <-> keys to adjust the value. The
values range from 200k Hz to 350k Hz with a 50k Hz interval.
CPU Power Phase Control [Standard]
Allows you to control the power phase based on the CPU’s demands. Configuration options:
[Standard] [Optimized] [Extreme] [Manual Adjustment]
DO NOT remove the thermal module when switching to Extreme and Manual Mode. The
thermal conditions should be monitored.
Manual Adjustment [Medium]
This item appears only when you set the previous item to [Manual Adjustment]. Select [Ultra
Fast] for a faster response. The reaction time will be longer when [Regular] is selected.
Configuration options: [Ultra Fast] [Fast] [Medium] [Regular]
CPU Power Duty Control [T.Probe]
DIGI + VRM Duty control adjusts the current and thermal conditions of every component’s
phase.
[T. Probe]
[Extreme]
Select to maintain the VRM thermal balance.
Select to maintain the current VRM balance.
CPU Current Capability [100%]
Allows you to configure the total power range, and extends the overclocking frequency range
simultaneously. Configuration options: [100%] [110%] [120%]
Choose a higher value when overclocking, or under a high CPU loading for extra power
support.
Chapter 2: BIOS information
2-15
Some of the following items are adjusted by typing the desired values using the numeric
keypad and press the <Enter> key. You can also use the <+> and <-> keys to adjust the
value. To restore the default setting, type [auto] using the keyboard and press the <Enter>
key.
2.4.8
CPU Voltage [Offset Mode]
[Offset Mode]
To offset the voltage by a positive or negative value.
[Manual Mode] Allows you to set a fixed CPU voltage.
Offset Mode Sign [+]
This item appears only when you set the CPU Voltage item to [Offset Mode].
[+]
[–]
To offset the voltage by a positive value.
To offset the voltage by a negative value.
CPU Offset Voltage [Auto]
Allows you to set the CPU Offset voltage. The values range from 0.005V to 0.635V with a 0.005V
interval.
CPU Manual Voltage [Auto]
This item appears only when you set the CPU Voltage item to [Manual Mode] and allows you
to set a fixed CPU voltage. The values range from 0.800V to 1.990V with a 0.005V interval.
Refer to the CPU documentation before setting the CPU voltage. Setting a high voltage
may damage the CPU permanently, and setting a low voltage may make the system
unstable.
2.4.9
DRAM Voltage [Auto]
Allows you to set the DRAM voltage. The values range from 1.185V to 2.135V with a 0.005V
interval.
According to Intel CPU specification, DIMMs with voltage requirement over 1.65V may
damage the CPU permanently. We recommend you install the DIMMs with the voltage
requirement below 1.65V.
2.4.10
VCCSA Voltage [Auto]
Allows you to set the VCCSA voltage. The values range from 0.610V to 1.560V with a 0.005V
interval.
2.4.11
PCH Voltage [Auto]
Allows you to set the Platform Controller Hub voltage. The values range from 0.7350V to
1.6850V with a 0.005V interval.
2.4.12
CPU PLL Voltage [Auto]
Allows you to set the CPU and PCH PLL voltage. Configuration options: [Auto] [+0.10V]
•
•
The values of the CPU Offset Voltage, CPU Manual Voltage, DRAM Voltage, VCCSA
Voltage, and PCH Voltage items are labeled in different color, indicating the risk levels
of high voltage settings.
The system may need better cooling system to work stably under high voltage settings.
2-16
ASUS P8H61 R2.0 Series
2.4.13
[Auto]
CPU Spread Spectrum [Auto]
Automatic configuration.
[Disabled]
[Enabled]
Enhances the BCLK overclocking ability.
Sets to [Enabled] for EMI control.
2.5
Advanced menu
The Advanced menu items allow you to change the settings for the CPU and other system
devices.
Be cautious when changing the settings of the Advanced menu items. Incorrect field values
can cause the system to malfunction.
Exit
UEFI BIOS Utility - Advanced Mode
Main
Ai Tweaker
Advanced
Monitor
Boot
Tool
CPU configuration parameters
>
>
>
>
>
>
>
>
CPU Configuration
PCH Configuration
SATA Configuration
System Agent Configuration
USB Configuration
Onboard Devices Configuration
APM
Network Stack
2.5.1
CPU Configuration
The items in this menu show the CPU-related information that the BIOS automatically
detects.
The items shown in submenu may be different due to the CPU you installed.
Intel Adaptive Thermal Monitor [Enabled]
[Enabled]
[Disabled]
Enables the overheated CPU to throttle its clock speed to cool down.
Disables the CPU thermal monitor function.
Hyper-threading [Enabled]
The Intel Hyper-Threading Technology allows a hyper-threading processor to appear as two
logical processors to the operating system, allowing the operating system to schedule two
threads or processes simultaneously.
[Enabled]
[Disabled]
Two threads per activated core are enabled.
Only one thread per activated core is enabled.
Chapter 2: BIOS information
2-17
Active Processor Cores [All]
Allows you to choose the number of CPU cores to activate in each processor package.
Configuration options: [All] [1] [2] [3]
Limit CPUID Maximum [Disabled]
[Enabled]
Allows legacy operating systems to boot even without support for CPUs
with extended CPUID functions.
[Disabled]
Disables this function.
Execute Disable Bit [Enabled]
[Enabled]
Enables the No-Execution Page Protection Technology.
Forces the XD feature flag to always return to zero (0).
[Disabled]
Intel® Virtualization Technology [Disabled]
[Enabled]
[Disabled]
Allows a hardware platform to run multiple operating systems separately
and simultaneously, enabling one system to virtually function as several
systems.
Disables this function.
Hardware Prefetcher [Enabled]
[Enabled]
[Disabled]
Allows a hardware platform to run multiple operating systems separately
and simultaneously, enabling one system to virtually function as several
systems.
Disables this function.
Adjacent Cache Line Prefetch [Enabled]
[Enabled]
[Disabled]
Allows a hardware platform to perform adjacent cache line prefetching.
Disables this function.
CPU Power Management Configuration
CPU Ratio [Auto]
Allows you to set the ratio between the CPU Core Clock and the BCLK Frequency. Use <+> and
<-> keys to adjust the ratio. The valid value ranges vary according to your CPU model.
Enhanced Intel SpeedStep Technology [Enabled]
Allows you to enable or disable the Enhanced Intel® SpeedStep Technology (EIST).
[Disabled]
[Enabled]
The CPU runs at its default speed.
The operating system controls the CPU speed.
Turbo Mode [Enabled]
Allows you to enable or disable the Intel® Turbo Mode Technology.
[Enabled]
Allows processor cores to run faster than marked frequency in specific condition.
[Disabled]
Disables this function.
CPU C1E [Auto]
Enables or disables the C1E support function. This item should be enabled in order to enable the
Enhanced Halt State. Configuration options: [Auto] [Enabled] [Disabled]
CPU C3 Report [Auto]
Allows you to disable or enable the CPU C3 report to OS. Configuration options: [Auto] [Enabled]
[Disabled]
2-18
ASUS P8H61 R2.0 Series
CPU C6 Report [Auto]
Allows you to disable or enable the CPU C6 report to OS. Configuration options: [Auto] [Enabled]
[Disabled]
2.5.2
PCH Configuration
High Precision Timer [Enabled]
Allows you to enable or disable the High Precision Event Timer.
Configuration options: [Enabled] [Disabled]
2.5.3
SATA Configuration
While entering Setup, the BIOS automatically detects the presence of SATA devices. The
SATA Port items show Empty if no SATA device is installed to the corresponding SATA port.
SATA Mode Selection [IDE]
Allows you to set the SATA configuration.
[Disabled]
[IDE]
Disables the SATA function.
Set to [IDE] when you want to use the Serial ATA hard disk drives as
Parallel ATA physical storage devices.
[AHCI]
Set to [AHCI] when you want the SATA hard disk drives to use the AHCI
(Advanced Host Controller Interface). The AHCI allows the onboard storage
driver to enable advanced Serial ATA features that increases storage
performance on random workloads by allowing the drive to internally
optimize the order of commands.
•
•
Due to H61 Chipset limitation, AHCI Mode only works on Windows® Vista / Windows® 7.
Please use IDE Mode on Windows® XP.
[IDE] is the default SATA type. Under Windows® XP, there is no need to change the
SATA type.
S.M.A.R.T. Status Check [Enabled]
S.M.A.R.T. (Self-Monitoring, Analysis and Reporting Technology) is a monitor system. When
read/write of your hard disk errors occur, this feature allows the hard disk to report warning
messages during the POST. Configuration options: [Enabled] [Disabled]
Hot Plug [Disabled]
This item only appears when you set the SATA Mode Selection item to [AHCI] and allows you
to enable or disable the hot-plug support for each SATA port. Configuration options: [Enabled]
[Disabled]
2.5.4
System Agent Configuration
Memory Remap Feature [Enabled]
[Enabled]
[Disabled]
Allow you to enable remapping the memory above 4GB.
Disables this function.
Graphics Configuration
Primary Display [Auto]
Allows you to decide which graphics controller to use as the primary boot device. Configuration
options: [Auto] [PEG] [PCI]
Chapter 2: BIOS information
2-19
2.5.5
USB Configuration
The items in this menu allow you to change the USB-related features.
The USB Devices item shows the auto-detected values. If no USB device is detected, the
item shows None.
Legacy USB Support [Enabled]
[Enabled]
[Disabled]
[Auto]
Enables the support for USB devices on legacy operating systems (OS).
The USB devices can be used only for the BIOS setup program.
Allows the system to detect the presence of USB devices at startup. If
detected, the USB controller legacy mode is enabled. If no USB device is
detected, the legacy USB support is disabled.
Legacy USB3.0 Support [Enabled] (P8H61/USB3 R2.0 only)
[Enabled]
Enables the support for USB 3.0 devices on legacy operating systems
(OS).
[Disabled]
Disables the function.
EHCI Hand-off [Disabled]
[Enabled]
Enables the support for operating systems without an EHCI hand-off
feature.
[Disabled]
Disables the function.
2.5.6
Onboard Devices Configuration
HD Audio Controller [Enabled]
[Enabled]
Enables the High Definition Audio Controller.
[Disabled]
Disables the controller.
The following two items appear only when you set the HD Audio Controller item to
[Enabled].
Front Panel Type [HD]
Allows you to set the front panel audio connector (AAFP) mode to legacy AC’97 or high-
definition audio depending on the audio standard that the front panel audio module supports.
[HD]
Sets the front panel audio connector (AAFP) mode to high definition audio.
[AC97]
Sets the front panel audio connector (AAFP) mode to legacy AC’97
SPDIF Out Type [SPDIF]
[SPDIF]
[HDMI]
Sets to [SPDIF] for SPDIF audio output.
Sets to [HDMI] for HDMI audio output.
Realtek LAN Controller [Enabled]
[Enabled]
[Disabled]
Enables the Realtek LAN controller.
Disables the controller.
2-20
ASUS P8H61 R2.0 Series
Realtek PXE OPROM [Disabled]
This item appears only when you set the previous item to [Enabled] and allows you to
enable or disable the PXE OptionRom of the Realtek LAN controller. Configuration options:
[Enabled] [Disabled]
Asmedia USB 3.0 Controller [Enabled] (P8H61/USB3 R2.0 only)
[Enabled] Enables the onboard USB 3.0 controller.
[Disabled] Disables the controller.
Asmedia USB 3.0 Battery Charging Support [Disabled] (P8H61/USB3 R2.0
only)
This item appears only when the Asmedia USB 3.0 Controller item is set to [Enabled].
[Enabled]
[Disabled]
Enables the Asmedia USB 3.0 battery charging function.
Disables this function
Serial Port Configuration
The sub-items in this menu allow you to set the serial port configuration.
Serial Port [Enabled]
Allows you to enable or disable the serial port (COM).
Configuration options: [Enabled] [Disabled]
Change Settings [IO=3F8h; IRQ=4]
Allows you to select the Serial Port base address. Configuration options: [IO=3F8h; IRQ=4]
[IO=2F8h; IRQ=3] [IO=3E8h; IRQ=4] [IO=2E8h; IRQ=3]
Parallel Port Configuration
The sub-items in this menu allow you to set the parallel port configuration.
Parallel Port [Enabled]
Allows you to enable or disable the parallel port (LPT).
Configuration options: [Enabled] [Disabled]
Change Settings [Auto]
Allows you to select an optimal setting for Super I/O devices. Configuration options: [Auto]
[IO=378h; IRQ=5;] [IO=378h; IRQ=5,6,7,9,10,11,12;] [IO=278h; IRQ=5,6,7,9,10,11,12;] [IO=3BCh;
IRQ=5,6,7,9,10,11,12;]
Device Mode [STD Printer Mode]
Allows you to change the printer port mode. Configuration options: [STD Printer Mode] [SPP Mode]
[EPP-1.9 and SPP Mode] [EPP-1.7 and SPP Mode] [ECP Mode] [ECP and EPP 1.9 Mode] [ECP
and EPP 1.7 Mode]
2.5.7
APM
Restore AC Power Loss [Power Off]
[Power On]
[Power Off]
[Last State]
The system goes into on state after an AC power loss.
The system goes into off state after an AC power loss.
The system goes into either off or on state, whatever the system state was
before the AC power loss.
Chapter 2: BIOS information
2-21
Power On By PS/2 Keyboard [Disabled]
[Disabled]
[Space Bar]
[Ctrl-Esc]
Disables the Power On by a PS/2 keyboard.
Sets the Space Bar on the PS/2 keyboard to turn on the system.
Sets the Ctrl+Esc key on the PS/2 keyboard to turn on the system.
[Power Key]
Sets Power key on the PS/2 keyboard to turn on the system. This feature
requires an ATX power supply that provides at least 1A on the +5VSB lead.
Power On By PS/2 Mouse [Disabled]
[Disabled]
[Enabled]
Disables the Power On by a PS/2 mouse.
Enables the Power On by a PS/2 mouse. This feature requires an ATX
power supply that provides at least 1A on the +5VSB lead.
Power On By PCI [Disabled]
[Disabled]
[Enabled]
Disables the PCI devices to generate a wake event.
Enables the PCI devices to generate a wake event.
Power On By PCIE [Disabled]
[Disabled]
[Enabled]
Disables the PCIE devices to generate a wake event.
Enables the PCIE devices to generate a wake event.
Power On By Ring [Disabled]
[Disabled]
[Enabled]
Disables Ring to generate a wake event.
Enables Ring to generate a wake event.
Power On By RTC [Disabled]
[Disabled]
[Enabled]
Disables RTC to generate a wake event.
When set to [Enabled], the items RTC Alarm Date (Days) and Hour/
Minute/Second will become user-configurable with set values.
2.5.8
Network Stack
Network Stack [Disable Link]
This item allows user to disable or enable the UEFI network stack. Configuration options:
[Disable Link] [Enabled]
Ipv4 PXE Support [Enabled]
This item appears only when you set the Network Stack item to [Enabled]. When this item is
disabled, the IPV4 PXE boot option will not be created. Configuration options: [Disable Link]
[Enabled]
Ipv6 PXE Support [Enabled]
This item appears only when you set the Network Stack item to [Enabled]. When this item is
disabled, the IPV6 PXE boot option will not be created. Configuration options: [Disable Link]
[Enabled]
2-22
ASUS P8H61 R2.0 Series
2.6
Monitor menu
The Monitor menu displays the system temperature/power status, and allows you to change
the fan settings.
Exit
UEFI BIOS Utility - Advanced Mode
Main
Ai Tweaker
Advanced
Monitor
Boot
Tool
CPU Temperature
MB Temperature
CPU Fan Speed
+45ºC / +113ºF
+34ºC / +93ºF
3325 RPM
N/A
Chassis Fan Speed
CPU Q-Fan Control
Enabled
CPU Fan Speed Low Limit
CPU Fan Profile
200 RPM
Standard
Enabled
Chassis Q-Fan Control
Chassis Fan Speed Low Limit
Chassis Fan Profile
CPU Voltage
200 RPM
Standard
+1.184 V
+3.312 V
+5.080 V
+12.192 V
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Shortcut
3.3V Voltage
F5: Optimized Defaults
F10: Save ESC: Exit
F12: Print Screen
5V Voltage
12V Voltage
Version 2.10.1208. Copyright (C) 2012 American Megatrends, Inc.
Scroll down to display the following items:
Anti Surge Support
Enabled
Version 2.10.1208. Copyright (C) 2012 American Megatrends, Inc.
Chapter 2: BIOS information
2-23
2.6.1
CPU Temperature / MB Temperature [xxx�C/xxx�F]
The onboard hardware monitor automatically detects and displays the CPU and motherboard
temperatures. Select Ignore if you do not wish to display the detected temperatures.
2.6.2
CPU / Chassis Fan Speed [xxxx RPM] or [Ignore] / [N/A]
The onboard hardware monitor automatically detects and displays the CPU and chassis fan
speeds in rotations per minute (RPM). If the fan is not connected to the motherboard, the field
shows N/A. Select Ignore if you do not wish to display the detected speed.
2.6.3
CPU Voltage, 3.3V Voltage, 5V Voltage, 12V Voltage
The onboard hardware monitor automatically detects the voltage output through the onboard
voltage regulators. Select Ignore if you do not want to detect this item.
2.6.4
CPU Q-Fan Control [Enabled]
Disables the CPU Q-Fan control feature.
Enables the CPU Q-Fan control feature.
[Disabled]
[Enabled]
CPU Fan Speed Low Limit [200 RPM]
This item appears only when you enable the CPU Q-Fan Control feature and allows you to
disable or set the CPU fan warning speed.
Configuration options: [Ignore] [200 RPM] [300 RPM] [400 RPM] [500 RPM] [600 RPM]
CPU Fan Profile [Standard]
This item appears only when you enable the CPU Q-Fan Control feature and allows you to set the
appropriate performance level of the CPU fan.
[Standard]
Sets to [Standard] to make the CPU fan automatically adjust depending on the CPU
temperature.
[Silent]
[Turbo]
[Manual]
Sets to [Silent] to minimize the fan speed for quiet CPU fan operation.
Sets to [Turbo] to achieve maximum CPU fan speed.
Sets to [Manual] to assign detailed fan speed control parameters.
The following four items appear only when you set CPU Fan Profile to [Manual].
CPU Upper Temperature [70]
Use the <+> and <-> keys to adjust the upper limit of the CPU temperature. The values range
from 20ºC to 75ºC.
CPU Fan Max. Duty Cycle(%) [100]
Use the <+> and <-> keys to adjust the maximum CPU fan duty cycle. The values range from
20% to 100%. When the CPU temperature reaches the upper limit, the CPU fan will operate at
the maximum duty cycle.
CPU Lower Temperature [20]
Use the <+> and <-> keys to adjust the lower limit of the CPU temperature. The values range
from 20ºC to 75ºC.
CPU Fan Min. Duty Cycle(%) [20]
Use the <+> and <-> keys to adjust the minimum CPU fan duty cycle. The values range from 0%
to 100%. When the CPU temperature is under 40ºC, the CPU fan will operate at the minimum
duty cycle.
2-24
ASUS P8H61 R2.0 Series
2.6.5
Chassis Q-Fan Control [Enabled]
Disables the Chassis Q-Fan control feature.
Enables the Chassis Q-Fan control feature.
[Disabled]
[Enabled]
Chassis Fan Speed Low Limit [200 RPM]
This item appears only when you enable the Chassis Q-Fan Control feature and allows you
to disable or set the chassis fan warning speed.
Configuration options: [Ignore] [200 RPM] [300 RPM] [400 RPM] [500 RPM] [600 RPM]
Chassis Fan Profile [Standard]
This item appears only when you enable the Chassis Q-Fan Control feature and allows you to set
the appropriate performance level of the chassis fan.
[Standard]
Sets to [Standard] to make the chassis fan automatically adjust depending on the
chassis temperature.
[Silent]
[Turbo]
[Manual]
Sets to [Silent] to minimize the fan speed for quiet chassis fan operation.
Sets to [Turbo] to achieve maximum chassis fan speed.
Sets to [Manual] to assign detailed fan speed control parameters.
The following four items appear only when you set Chassis Fan Profile to [Manual].
Chassis Upper Temperature [70]
Use the <+> and <-> keys to adjust the upper limit of the CPU temperature. The values range
from 40ºC to 90ºC.
Chassis Fan Max. Duty Cycle(%) [100]
Use the <+> and <-> keys to adjust the maximum chassis fan duty cycle. The values range
from 60% to 100%. When the chassis temperature reaches the upper limit, the chassis fan will
operate at the maximum duty cycle.
Chassis Lower Temperature [40]
Displays the lower limit of the chassis temperature.
CPU Fan Min. Duty Cycle(%) [60]
Use the <+> and <-> keys to adjust the minimum chassis fan duty cycle. The values range from
60% to 100%. When the chassis temperature is under 40ºC, the chassis fan will operate at the
minimum duty cycle.
2.6.6
Anti Surge Support [Enabled]
This item allows you to enable or disable the Anti Surge function.
Configuration options: [Disabled] [Enabled]
Chapter 2: BIOS information
2-25
2.7
Boot menu
The Boot menu items allow you to change the system boot options.
Exit
UEFI BIOS Utility - Advanced Mode
Main
Ai Tweaker
Advanced
Monitor
Boot
Tool
Select the keyboard NumLock state
Bootup NumLock State
Full Screen Logo
On
Enabled
Enabled
Wait For ‘F1’ If Error
Option ROM Messages
Setup Mode
Force BIOS
EZ Mode
UEFI/Legacy Boot
PCI ROM Priority
Enabled both...
Legacy ROM
Boot Option Priorities
Boot Option #1
SATA: xxxxxxx
SATA: xxxxxxx
→←: Select Screen
↑↓: Select Item
Enter: Select
Boot Option #2
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Shortcut
Boot Override
>
>
>
SATA: xxxxxxxxxxxx
F5: Optimized Defaults
F10: Save ESC: Exit
F12: Print Screen
Hard Drive BBS Priorities
CD/DVD ROM Drive BBS Priorities
Version 2.10.1208. Copyright (C) 2012 American Megatrends, Inc.
2.7.1
[On]
Bootup NumLock State [On]
Sets the power-on state of the NumLock to [On].
Sets the power-on state of the NumLock to [Off].
[Off]
2.7.2
Full Screen Logo [Enabled]
[Enabled]
[Disabled]
Enables the full screen logo display feature.
Disables the full screen logo display feature.
Set this item to [Enabled] to use the ASUS MyLogo 2™ feature.
Post Report [5 sec]
This item appears only when the Full Screen Logo item is set to [Disabled] and allows you to
set the waiting time for the system to display the post report. Configuration options: [1 sec] [2
sec] [3 sec] [4 sec] [5 sec] [6 sec] [7 sec] [8 sec] [9 sec] [10 sec] [Until Press ESC]
2.7.3
Wait for ‘F1’ If Error [Enabled]
When this item is set to [Enabled], the system waits for the F1 key to be pressed when error
occurs. Configuration options: [Disabled] [Enabled]
2-26
ASUS P8H61 R2.0 Series
2.7.4
Option ROM Messages [Force BIOS]
[Force BIOS]
The third-party ROM messages will be forced to display during the boot
sequence.
[Keep Current] The third-party ROM messages will be displayed only if the third-party
manufacturer had set the add-on device to do so.
2.7.5
Setup Mode [EZ Mode]
[Advanced Mode] Sets Advanced Mode as the default screen for entering the BIOS setup
program.
[EZ Mode]
Sets EZ Mode as the default screen for entering the BIOS setup program.
2.7.6
UEFI/Legacy Boot [Enabled both UEFI and Legacy]
[Enable both UEFI and Legacy] Enables both UEFI and Legacy boot.
[Disable UEFI]
Enables the Legacy boot, and disables the UEFI boot.
Enables the UEFI boot, and disables the Legacy boot.
[Disable Legacy]
2.7.7
PCI ROM Priority [Legacy ROM]
[Legacy ROM]
Launch Legacy ROM
[EFI Compatibe ROM] Launch UEFI Compatible ROM
2.7.8
Boot Option Priorities
These items specify the boot device priority sequence from the available devices. The
number of device items that appears on the screen depends on the number of devices
installed in the system.
•
•
To select the boot device during system startup, press <F8> when ASUS Logo appears.
To access Windows OS in Safe Mode, press <F8> after POST.
2.7.9
Boot Override
These items displays the available devices. The number of device items that appears on
the screen depends on the number of devices installed in the system. Click an item to start
booting from the selected device.
Chapter 2: BIOS information
2-27
2.8
Tools menu
The Tools menu items allow you to configure options for special functions. Select an item
then press <Enter> to display the submenu.
Exit
UEFI BIOS Utility - Advanced Mode
Main
Ai Tweaker
Advanced
Monitor
Boot
Tool
Be used to update BIOS
>
>
>
ASUS EZ Flash 2 Utility
ASUS SPD Information
ASUS O.C. Profile
2.8.1
ASUS EZ Flash 2 Utility
Allows you to run ASUS EZ Flash 2. Press [Enter] to launch the ASUS EZ Flash 2 screen.
For more details, see section 2.1.2 ASUS EZ Flash 2.
2.8.2
ASUS SPD Information
DIMM Slot # [Slot 1]
Displays the Serial Presence Detect (SPD) information of the DIMM module installed on the
selected slot. Configuration options: [Slot 1] [Slot 2]
2.8.3
ASUS O.C. Profile
This item allows you to store or load multiple BIOS settings.
The Setup Profile Status items show Not Installed if no profile is created.
Label
Allows you to input the label of the setup profile.
Save to Profile
Allows you to save the current BIOS settings to the BIOS Flash, and create a profile. Key in a
profile number from one to eight, press <Enter>, and then select Yes.
Load from Profile
Allows you to load the previous BIOS settings saved in the BIOS Flash. Key in the profile
number that saved your CMOS settings, press <Enter>, and then select Yes.
•
DO NOT shut down or reset the system while updating the BIOS to prevent the system
boot failure!
•
We recommend that you update the BIOS file only coming from the same memory/CPU
configuration and BIOS version.
2-28
ASUS P8H61 R2.0 Series
2.9
Exit menu
The Exit menu items allow you to load the optimal default values for the BIOS items, and
save or discard your changes to the BIOS items. You can access the EZ Mode from the Exit
menu.
Exit
Load Optimized Defaults
Save Changes & Reset
Discard Changes & Exit
ASUS EZ Mode
Launch EFI Shell from filesystem device
Load Optimized Defaults
This option allows you to load the default values for each of the parameters on the Setup
menus. When you select this option or if you press <F5>, a confirmation window appears.
Select Yes to load the default values.
Save Changes & Reset
Once you are finished making your selections, choose this option from the Exit menu to
ensure the values you selected are saved. When you select this option or if you press <F10>,
a confirmation window appears. Select Yes to save changes and exit.
Discard Changes & Exit
This option allows you to exit the Setup program without saving your changes. When you
select this option or if you press <Esc>, a confirmation window appears. Select Yes to
discard changes and exit.
ASUS EZ Mode
This option allows you to enter the EZ Mode screen.
Launch EFI Shell from filesystem device
This option allows you to attempt to launch the EFI Shell application (shellx64.efi) from one of
the available devices that have a filesystem.
Chapter 2: BIOS information
2-29
2-30
ASUS P8H61 R2.0 Series
Appendices
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
•
•
This device may not cause harmful interference.
This device must accept any interference received including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with manufacturer’s instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.
•
Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the graphics card is required
to assure compliance with FCC regulations. Changes or modifications to this unit not
expressly approved by the party responsible for compliance could void the user’s authority
to operate this equipment.
IC: Canadian Compliance Statement
Complies with the Canadian ICES-003 Class B specifications. This device complies with RSS
210 of Industry Canada. This Class B device meets all the requirements of the Canadian
interference-causing equipment regulations.
This device complies with Industry Canada license exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may cause undesired
operation of the device.
Cut appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada.
Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le
matériel brouilleur du Canada.
Cet appareil est conforme aux normes CNR exemptes de licence d’Industrie Canada. Le
fonctionnement est soumis aux deux conditions suivantes :
(1) cet appareil ne doit pas provoquer d’interférences et
(2) cet appareil doit accepter toute interférence, y compris celles susceptibles de provoquer
un fonctionnement non souhaité de l’appareil.
Appendices
A-1
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions from
digital apparatus set out in the Radio Interference Regulations of the Canadian Department
of Communications.
This class B digital apparatus complies with Canadian ICES-003.
VCCI: Japan Compliance Statement
VCCI Class B Statement
KC: Korea Warning Statement
REACH
Complying with the REACH (Registration, Evaluation, Authorisation, and Restriction of
Chemicals) regulatory framework, we published the chemical substances in our products at
DO NOT throw the motherboard in municipal waste. This product has been designed to
enable proper reuse of parts and recycling. This symbol of the crossed out wheeled bin
indicates that the product (electrical and electronic equipment) should not be placed in
municipal waste. Check local regulations for disposal of electronic products.
DO NOT throw the mercury-containing button cell battery in municipal waste. This symbol
of the crossed out wheeled bin indicates that the battery should not be placed in municipal
waste.
ASUS Recycling/Takeback Services
ASUS recycling and takeback programs come from our commitment to the highest standards for
protecting our environment. We believe in providing solutions for you to be able to responsibly
recycle our products, batteries, other components as well as the packaging materials. Please
regions.
A-2
ASUS P8H61 R2.0 Series
ASUS contact information
ASUSTeK COMPUTER INC.
Address
Telephone
Fax
E-mail
Web site
15 Li-Te Road, Peitou, Taipei, Taiwan 11259
+886-2-2894-3447
+886-2-2890-7798
Technical Support
Telephone
Online support
+86-21-38429911
support.asus.com
ASUS COMPUTER INTERNATIONAL (America)
Address
Telephone
Fax
800 Corporate Way, Fremont, CA 94539, USA
+1-510-739-3777
+1-510-608-4555
usa.asus.com
Web site
Technical Support
Telephone
Support fax
+1-812-282-2787
+1-812-284-0883
support.asus.com
Online support
ASUS COMPUTER GmbH (Germany and Austria)
Address
Harkort Str. 21-23, D-40880 Ratingen, Germany
Fax
Web site
Online contact
+49-2102-959911
Technical Support
Telephone
Support Fax
+49-1805-010923*
+49-2102-9599-11
support.asus.com
Online support
* EUR 0.14/minute from a German fixed landline; EUR 0.42/minute from a mobile phone.
|