VW202/VW222 Series
LCD Monitor
User Guide
Contents
Notices......................................................................................................... iv
Safety information ...................................................................................... vi
Care & Cleaning ........................................................................................ vii
Chapter 1:
Product introduction
1.1
1.2
1.3
Welcome! .................................................................................... 1-1
Package contents......................................................................... 1-1
Monitor introduction.................................................................... 1-2
1.3.1
1.3.2
Front view ....................................................................... 1-2
Back view........................................................................ 1-3
Chapter 2:
Setup
2.1
2.2
2.3
2.4
2.5
Assembling the monitor base..................................................... 2-1
Adjusting the monitor.................................................................. 2-1
Detaching the arm/base (for VESA wall mount)........................ 2-2
Connecting the cables................................................................. 2-3
Turning on the monitor................................................................ 2-3
Chapter 3:
General instruction
3.1
OSD (On-Screen Display) menu ................................................ 3-1
3.1.1
3.1.2
How to reconfigure.......................................................... 3-1
OSD Function Introduction.............................................. 3-1
3.2
3.3
3.4
Specifications summary.............................................................. 3-4
Troubleshooting (FAQ) .............................................................. 3-11
Supported operating modes ..................................................... 3-12
iii
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
•
•
This device may not cause harmful interference, and
This device must accept any interference received including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with manufacturer’s
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the graphics card is
required to assure compliance with FCC regulations. Changes or modifications
to this unit not expressly approved by the party responsible for compliance
could void the user’s authority to operate this equipment.
As an Energy Star® Partner, our company has determined that this product meets
the Energy Star® guidelines for energy efficiency.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions
from digital apparatus set out in the Radio Interference Regulations of the
Canadian Department of Communications.
This class B digital apparatus complies with Canadian ICES-003.
iv
TCO Development
Congratulations!
The display you have just purchased carries the
TCO’03 Displays label. This means that your
display is designed, manufactured and tested
according to some of the strictest quality and
environmental requirements in the world. This
makes for a high performance product, designed
with the user in focus that also minimizes the
impact on our natural environment.
Some of the features of the TCO’03 Display requirements:
Ergonomics
•
Good visual ergonomics and image quality in order to improve the working
environment for the user and to reduce sight and strain problems. Important
parameters are luminance, contrast, resolution, reflectance, colour rendition
and image stability.
Energy
•
Energy-saving mode after a certain time – beneficial both for the user and the
environment
•
Electrical safety
Emissions
•
•
Electromagnetic fields
Noise emissions
Ecology
•
The product must be prepared for recycling and the manufacturer must have a
certified environmental management system such as EMAS or ISO 14 001
•
Restrictions on
- chlorinated and brominated flame retardants and polymers
- heavy metals such as cadmium, mercury and lead.
The requirements included in this label have been developed by TCO
Development in cooperation with scientists, experts, users as well as
manufacturers all over the world. Since the end of the 1980s TCO has been
involved in influencing the development of IT equipment in a more user-friendly
direction. Our labelling system started with displays in 1992 and is now requested
by users and IT-manufacturers all over the world.
v
Safety information
•
Before setting up the monitor, carefully read all the documentation that came
with the package.
•
•
To prevent fire or shock hazard, never expose the monitor to rain or moisture.
Never try to open the monitor cabinet. The dangerous high voltages inside the
monitor may result in serious physical injury.
•
•
If the power supply is broken, do not try to fix it by yourself. Contact a qualified
service technician or your retailer.
Before using the product, make sure all cables are correctly connected and the
power cables are not damaged. If you detect any damage, contact your dealer
immediately.
•
•
Slots and openings on the back or top of the cabinet are provided for
ventilation. Do not block these slots. Never place this product near or over a
radiator or heat source unless proper ventilation is provided.
The monitor should be operated only from the type of power source indicated
on the label. If you are not sure of the type of power supply to your home,
consult your dealer or local power company.
•
•
•
•
•
•
Use the appropriate power plug which complies with your local power
standard.
Do not overload power strips and extention cords. Overloading can result in
fire or electric shock.
Avoid dust, humidity, and temperature extremes. Do not place the monitor in
any area where it may become wet. Place the monitor on a stable surface.
Unplug the unit during a lightning storm or if it will not be used for a long period
of time. This will protect the monitor from damage due to power surges.
Never push objects or spill liquid of any kind into the slots on the monitor
cabinet.
To ensure satisfactory operation, use the monitor only with UL listed
computers which have appropriate configured receptacles marked between
100-240V AC.
•
If you encounter technical problems with the monitor, contact a qualified
service technician or your retailer.
This symbol of the crossed out wheeled bin indicates that the product (electrical
and electronic equipment) should not be placed in municipal waste.
Please check local regulations for disposal of electronic products.
vi
Care & Cleaning
•
Before you lift or reposition your monitor, it is better to disconnect the cables
and power cord. Follow the correct lifting techniques when positioning the
monitor. When lifting or carrying the monitor, grasp the edges of the monitor.
Do not lift the display by the stand or the cord.
•
•
Cleaning. Turn your monitor off and unplug the power cord. Clean the monitor
surface with a lint-free, non-abrasive cloth. Stubborn stains may be removed
with a cloth dampened with mild cleaner.
Avoid using a cleaner containing alcohol or acetone. Use a cleaner intended
for use with the LCD. Never spray cleaner directly on the screen, as it may drip
inside the monitor and cause an electric shock.
The following symptoms are normal with the monitor:
•
The screen may flicker during the initial use due to the nature of the fluorescent
light. Turn off the Power Switch and turn it on again to make sure that the
flicker disappears.
•
•
You may find slightly uneven brightness on the screen depending on the
desktop pattern you use.
When the same image is displayed for hours, an afterimage of the previous
screen may remain after switching the image. The screen will recover slowly or
you can turn off the Power Switch for hours.
•
When the screen becomes black or flashes, or cannot work anymore, contact
your dealer or service center to fix it. Do not repair the screen by yourself!
Conventions used in this guide
WARNING: Information to prevent injury to yourself when trying to
complete a task.
CAUTION: Information to prevent damage to the components when trying
to complete a task.
IMPORTANT: Information that you MUST follow to complete a task.
NOTE: Tips and additional information to aid in completing a task.
vii
Where to find more information
Refer to the following sources for additional information and for product and
software updates.
1.
2.
ASUS websites
The ASUS websites worldwide provide updated information on ASUS
Optional documentation
Your product package may include optional documentation that may have
been added by your dealer. These documents are not part of the standard
package.
viii
1.1
Welcome!
Thank you for purchasing the ASUS® VW202/VW222 Series LCD monitor!
The latest widescreen LCD monitor from ASUS provides a crisper, broader, and
brighter display, plus a host of features that enhance your viewing experience.
With these features, you can enjoy the convenience and delightful visual
experience that the VW202/VW222 Series brings you!
1.2
Package contents
Check your VW202/VW222 Series LCD monitor package for the following items:
LCD monitor
Quick start guide
1 x Power cord
1 x VGA cable
1 x DVI cable
1 x Audio cable
If any of the above items is damaged or missing, contact your retailer
immediately.
ASUS VW202/VW222 Series LCD Monitor
1-1
1.3
Monitor introduction
1.3.1
Front view
Base
4
5
1
2
3
1.
Button:
•
Use this hotkey to switch from five video preset modes (Game
Mode, Night View Mode, Scenery Mode, Standard Mode, Theater Mode)
with SPLENDID™ Video Enhancement Technology.
•
•
Exit the OSD menu or go back to the previous menu as the OSD menu
is active.
Automatically adjust the image to its optimized position, clock, and phase
by pressing this button for 2-4 seconds (for VGA mode only).
2.
Button:
•
Press this button to decrease the value of the function selected or move
left/up to the previous function.
•
This is also a hotkey for Volume adjustment.
3.
4.
MENU Button:
•
Press this button to enter/select the icon (function) highlighted while the
OSD is activated.
Button:
•
•
Press this button to increase the value of the function selected or move
right/down to the next fuction.
This is also a hotkey for Brightness adjustment.
1-2
Chapter 1: Product introduction
5.
Power button/power indicator
•
•
Press this button to turn the monitor on/off
The color definition of the power indicator is as the below table.
Status
Blue
Description
ON
Amber
OFF
Standby mode
OFF
1.3.2
Back view
Stereo
speaker
Stereo
speaker
Screw holes for
VESA Wall Mount
Rear connectors
1
2
3
4
Rear connectors
1.
2.
3.
4.
Audio-in port. This port connects PC audio source by the bundled audio
cable.
AC-IN port. This port connects the power connector from the bundled power
cord.
DVI port. This 24-pin port is for PC (Personal Computer) DVI-D digital signal
connection.
VGA port. This 15-pin port is for PC VGA connection.
The VESA wall mount kit (100 mm x 100 mm) is purchased separately.
ASUS VW202/VW222 Series LCD Monitor
1-3
1-4
Chapter 1: Product introduction
2.1
Assembling the monitor base
To assemble the monitor base:
ꢀ.
2.
Have the front of the monitor face down on a table.
Connect the base with the arm according to the below drawing. A click shows
that the base has been connected successfully.
We recommend that you cover the table surface with soft cloth to prevent
damage to the monitor.
2.2
Adjusting the monitor
•
For optimal viewing, we recommend that you look at the full face of the
monitor, then adjust the monitor to the angle that is most comfortable for you.
•
•
Hold the stand to prevent the monitor from falling when you change its angle.
You can adjust the monitor’s angle from -3º to 20º.
-3º~20º
It is normal that the monitor slightly shakes while you adjust the the viewing
angle.
ASUS VW202/VW222 Series LCD Monitor
2-ꢀ
2.3
Detaching the arm/base
(for VESA wall mount)
The detachable arm/base of the VW202/VW222 Series LCD monitor is specially
designed for VESA wall mount.
To detach the arm/base:
ꢀ.
2.
3.
Have the front of the monitor face down on a table.
Remove the rubbers in the four screw holes (Figure ꢀ).
Use a screwdriver to remove the two screws on the arm (Figure ꢀ), then slide
out the arm/base to detach it from the monitor (Figure 2).
Rubbers in the
screw holes
Two screws
Arm/base
Figure 1
Figure 2
We recommend that you cover the table surface with soft cloth to prevent
damage to the monitor.
2-2
Chapter 2: Setup
2.4
Connecting the cables
ꢀ.
Connect the cables as the following instructions:
•
•
•
To connect the audio cable: connect one end of the audio cable to the
monitor’s Audio-in port, the other end to the computer's audio-out port.
To connect the power cord: connect one end of the power cord securely to
the monitor’s AC input port, the other end to a power outlet.
To connect the VGA/DVI cable:
a. Plug the VGA/DVI connector to the LCD monitor’s VGA/DVI port.
b. Connect the other end of the VGA/ DVI cable to your computer’s VGA/
DVI port.
c. Tighten the two screws to secure the VGA/DVI connector.
When both the VGA and the DVI cables are connected, you can choose either
VGA mode or DVI mode from the Input Select item of the OSD functions.
2.
Gather all the cables with the cable hook.
Cable hook
2.5
Turning on the monitor
Gently press the power button
button. The power indicator
. See page ꢀ-2 for the location of the power
lights up in blue to show that the monitor is ON.
ASUS VW202/VW222 Series LCD Monitor
2-3
2-ꢁ
Chapter 2: Setup
3.1
OSD (On-Screen Display) menu
3.1.1
How to reconfigure
ꢀ.
Press the MENU button to activate
the OSD menu.
2.
Press
the desired function by pressing the MENU button. If the function selected
has a sub-menu, press and again to navigate through the sub-menu
and
to navigate through the functions. Highlight and activate
functions. Highlight and activate the desired sub-menu function by pressing
the MENU button.
3.
ꢁ.
Press
and
to change the settings of the selected function.
To exit the OSD menu, press the
adjust any other function.
button. Repeat step 2 and step 3 to
3.1.2
OSD Function Introduction
1.
Spendid
This function contains five
sub-functions you can select
for your preference. Each mode has the
Reset selection, allowing you to maintain
your setting or return to the preset mode.
•
•
•
•
•
Scenery Mode: best choice for scenery photo display with SPLENDID™
Video Enhancement.
Standard Mode: best choice for document editing with SPLENDID™
Video Enhancement.
Theater Mode: best choice for movie with SPLENDID™ Video
Enhancement.
Game Mode: best choice for game playing with SPLENDID™ Video
Enhancement.
Night View Mode: best choice for dark-scene game or movie with
SPLENDID™ Video Enhancement.
•
In the Standard Mode, the Satuation and Sharpness functions are not
user-configurable.
•
In the other modes, the sRGB function is not user-configurable.
ASUS VW202/VW222 Series LCD Monitor
3-ꢀ
2.
Image
You can adjust brightness, contrast,
sharpness, saturation,position (VGA
only), ASCR, and focus (VGA only) from
this main function.
•
Brightness: the adjusting range is from 0 to ꢀ00.
is a hotkey to
activate this function.
•
•
•
•
•
Contrast: the adjusting range is from 0 to ꢀ00.
ASCR: turns on/off the ASCR(ASUS Smart Contrast Ratio) function.
Sharpness: the adjusting range is from 0 to ꢀ00.
Saturation: the adjusting range is from 0 to ꢀ00.
Position: adjusts the horizontal postition (H-Position) and the vertical
position (V-Position) of the image. The adjusting range is from 0 to ꢀ00.
•
Focus: reduces Horizonal-line noise and Vertical-line noise of the image
by adjusting (Phase) and (Clock) separately. The adjusting range is from
0 to ꢀ00.
•
•
Phase adjusts the phase of the pixel clock signal. With a wrong phase
adjustment, the screen shows horizontal disturbances.
Clock (pixel frequency) controls the number of pixels scanned by one
horizontal sweep. If the frequency is not correct, the screen shows vertical
stripes and the image is not proportional.
3.
Color
Select the image color you like
from this function.
•
•
Color Temp.: contains five color modes including Cool, Normal,
Warm, sRGB, and User mode.
Skin Tone: contains three color modes including Reddish, Natural,
and Yellowish.
In the User mode, colors of R (Red), G (Green), and B (Bluee) are user-
configurable; the adjusting range is from 0-ꢀ00.
3-2
Chapter 3: General Instruction
4.
Input Select
In this function, you can select
either VGA or DVI input source.
(Only for some models)
5.
System Setup
Allow you to adjust the system.
•
•
Volume: the adjusting range is from 0 to ꢀ00.
this function.
is a hotkey to activate
OSD Setup:
* Adjusts the horizontal postition (H-Position)/ the vertical position
(V-Position) of the OSD from 0 to ꢀ00.
* Adjusts the OSD timeout from ꢀ0 to ꢀ20.
*
Enables or disables the DDC/CI function.
•
Language: there are ten languages for your selection, including English,
German, Italian, French, Dutch, Spanish, Russian, Traditional Chinese,
Simplified Chinese, and Japanese.
•
•
•
Aspect Control: adjusts the aspect ratio to “Full” or “ꢁ:3”.
Information: shows the monitor information.
Reset: “Yes” allows you to restore the default setting.
ASUS VW202/VW222 Series LCD Monitor
3-3
3.2
Specifications summary (VW202U)
Panel Type
Panel size
TFT LCD
20" (16:10) wide screen
Max. Resolution
Pixel pitch
WSXGA+ 1680 x 1050
0.258mm
Brightness (Typ.)
Brightness (Max.)
Contrast Ratio (Typ.)
Contrast Ratio (Max.)
Viewing angle(H/V) CR>10
Display colors
250cd/m2
300cd/m2
800:1
2000:1 (with ASCR ON)
160˚/160˚
16.7M
Response time
2ms (Gray to Gray)
Yes
SPLENDID™ Video
Enhancement
SPLENDID™ selection
Auto adjustment
5 video preset modes (by hotkey)
Yes (by hotkey)
Color temperature selection 5 color temperatures
Skin-Tone selection
Digital input
3 skin-tones
DVI-D with HDCP
Analog input
Audio-in port
Colors
D-Sub
3.5 mm Mini-jack
Black
Speaker (Built-in)
Power LED
1W x 2 Stereo, RMS
Blue (On)/ Amber (Standby)
VESA wall mount
Tilt
100 x 100mm
+20˚~-3˚
Kensington lock
Voltage rating
Power consumption
Yes
AC: 100~240V
Power On : < ꢀ9W, Standby: < 2W, Power Off: <1W
Dimension (W x H x D)
ꢀ73 mm x 392 mm x 210 mm (machine)
570 mm x ꢀ55 mm x 150 mm (package)
ꢀ.ꢀ kg (Net) ; 6.5 kg (Gross)
Weight (Esti.)
Temperature (Operating)
0ºC~40ºC
Temperature
-20˚C~+60˚C
(Non-operating)
Humidity (Operating)
Humidity (Non-operating)
Multi-languages
10%~90%
5%~90%
10 languages (English, German, Italian, French, Dutch,
Spanish, Russian, Traditional Chinese, Simplified
Chinese, Japanese)
Accessories
VGA cable, DVI cable, audio cable, power cord, quick
start guide, warranty card
Energy Star®, CB, CE, Gost-R, CCC, CSA, FCC, C-Tick,
Regulation approvals
BSMI, VCCI, TCO03, RoHS, WEEE, PSB
*Specifications are subject to change without notice.
3-ꢀ
Chapter 3: General Instruction
Specifications summary (VW202T)
Panel Type
TFT LCD
Panel size
20" (16:10) wide screen
WSXGA+ 1680 x 1050
0.258mm
Max. Resolution
Pixel pitch
Brightness (Typ.)
Brightness (Max.)
Contrast Ratio (Typ.)
Contrast Ratio (Max.)
Viewing angle(H/V) CR>10
Display colors
250cd/m2
300cd/m2
800:1
2000:1 (with ASCR ON)
160˚/160˚
16.7M
Response time
5ms
SPLENDID™ Video
Enhancement
Yes
SPLENDID™ selection
Auto adjustment
5 video preset modes (by hotkey)
Yes (by hotkey)
Color temperature selection 5 color temperatures
Skin-Tone selection
Digital input
3 skin-tones
DVI-D with HDCP
Analog input
Audio-in port
Colors
D-Sub
3.5 mm Mini-jack
Black
Speaker (Built-in)
Power LED
1W x 2 Stereo, RMS
Blue (On)/ Amber (Standby)
VESA wall mount
Tilt
100 x 100mm
+20˚~-3˚
Kensington lock
Voltage rating
Power consumption
Yes
AC: 100~240V
Power On : < ꢀ9W, Standby: < 2W, Power Off: <1W
Dimension (W x H x D)
ꢀ73 mm x 392 mm x 210 mm (machine)
570 mm x ꢀ55 mm x 150 mm (package)
ꢀ.ꢀ kg (Net) ; 6.5 kg (Gross)
Weight (Esti.)
Temperature (Operating)
0˚C~40˚C
Temperature
-20˚C~+60˚C
(Non-operating)
Humidity (Operating)
Humidity (Non-operating)
Multi-languages
10%~90%
5%~90%
10 languages (English, German, Italian, French, Dutch,
Spanish, Russian, Traditional Chinese, Simplified
Chinese, Japanese)
Accessories
VGA cable, DVI cable, audio cable, power cord, quick
start guide, warranty card
Energy Star®, CB, CE, Gost-R, CCC, CSA, FCC, C-Tick,
Regulation approvals
BSMI, VCCI, TCO03, RoHS, WEEE, PSB
*Specifications are subject to change without notice.
ASUS VW202/VW222 Series LCD Monitor
3-5
Specifications summary (VW202S)
Panel Type
TFT LCD
Panel size
20" (16:10) wide screen
WSXGA+ 1680 x 1050
0.258mm
Max. Resolution
Pixel pitch
Brightness (Typ.)
Brightness (Max.)
Contrast Ratio (Typ.)
Contrast Ratio (Max.)
Viewing angle(H/V) CR>10
Display colors
250cd/m2
300cd/m2
800:1
2000:1 (with ASCR ON)
160˚/160˚
16.7M
Response time
5ms
SPLENDID™ Video
Enhancement
Yes
SPLENDID™ selection
Auto adjustment
5 video preset modes (by hotkey)
Yes (by hotkey)
Color temperature selection 5 color temperatures
Skin-Tone selection
Analog input
Audio-in port
Colors
3 skin-tones
D-Sub
3.5 mm Mini-jack
Black
Speaker (Built-in)
Power LED
1W x 2 Stereo, RMS
Blue (On)/ Amber (Standby)
VESA wall mount
Tilt
100 x 100mm
+20˚~-3˚
Kensington lock
Voltage rating
Power consumption
Yes
AC: 100~240V
Power On : < ꢀ9W, Standby: < 2W, Power Off: <1W
Dimension (W x H x D)
ꢀ73 mm x 392 mm x 210 mm (machine)
570 mm x ꢀ55 mm x 150 mm (package)
ꢀ.ꢀ kg (Net) ; 6.5 kg (Gross)
Weight (Esti.)
Temperature (Operating)
0˚C~40˚C
Temperature
-20˚C~+60˚C
(Non-operating)
Humidity (Operating)
Humidity (Non-operating)
Multi-languages
10%~90%
5%~90%
10 languages (English, German, Italian, French, Dutch,
Spanish, Russian, Traditional Chinese, Simplified
Chinese, Japanese)
Accessories
VGA cable, audio cable, power cord, quick start guide,
warranty card
Energy Star®, CB, CE, Gost-R, CCC, CSA, FCC, C-Tick,
Regulation approvals
BSMI, VCCI, TCO03, RoHS, WEEE, PSB
*Specifications are subject to change without notice.
3-6
Chapter 3: General Instruction
Specifications summary (VW202D)
Panel Type
TFT LCD
Panel size
20" (16:10) wide screen
WSXGA+ 1680 x 1050
0.258mm
Max. Resolution
Pixel pitch
Brightness (Typ.)
Brightness (Max.)
Contrast Ratio (Typ.)
Contrast Ratio (Max.)
Viewing angle(H/V) CR>10
Display colors
250cd/m2
300cd/m2
800:1
2000:1 (with ASCR ON)
160˚/160˚
16.7M
Response time
5ms
SPLENDID™ Video
Enhancement
Yes
SPLENDID™ selection
Auto adjustment
5 video preset modes (by hotkey)
Yes (by hotkey)
Color temperature selection 5 color temperatures
Skin-Tone selection
Analog input
Colors
3 skin-tones
D-Sub
Black
Power LED
Blue (On)/ Amber (Standby)
VESA wall mount
Tilt
100 x 100mm
+20˚~-3˚
Kensington lock
Voltage rating
Power consumption
Yes
AC: 100~240V
Power On : < ꢀ9W, Standby: < 2W, Power Off: <1W
Dimension (W x H x D)
ꢀ73 mm x 392 mm x 210 mm (machine)
570 mm x ꢀ55 mm x 150 mm (package)
ꢀ.ꢀ kg (Net) ; 6.5 kg (Gross)
Weight (Esti.)
Temperature (Operating)
0˚C~40˚C
Temperature
-20˚C~+60˚C
(Non-operating)
Humidity (Operating)
Humidity (Non-operating)
Multi-languages
10%~90%
5%~90%
10 languages (English, German, Italian, French, Dutch,
Spanish, Russian, Traditional Chinese, Simplified
Chinese, Japanese)
Accessories
VGA cable, power cord, quick start guide, warranty card
Regulation approvals
Energy Star®, CB, CE, Gost-R, CCC, CSA, FCC, C-Tick,
BSMI, VCCI, TCO03, RoHS, WEEE, PSB
*Specifications are subject to change without notice.
ASUS VW202/VW222 Series LCD Monitor
3-7
Specifications summary (VW222U)
Panel Type
TFT LCD
Panel size
22" (16:10) wide screen
WSXGA+ 1680 x 1050
0.282mm
Max. Resolution
Pixel pitch
Brightness (Typ.)
Brightness (Max.)
Contrast Ratio (Typ.)
Contrast Ratio (Max.)
Viewing angle(H/V) CR>10
Display colors
250cd/m2
300cd/m2
800:1
2000:1 (with ASCR ON)
170˚/160˚
16.7M
Response time
2ms (Gray to Gray)
Yes
SPLENDID™ Video
Enhancement
SPLENDID™ selection
Auto adjustment
5 video preset modes (by hotkey)
Yes (by hotkey)
Color temperature selection 5 color temperatures
Skin-Tone selection
Digital input
3 skin-tones
DVI-D with HDCP
Analog input
Audio-in port
Colors
D-Sub
3.5 mm Mini-jack
Black
Speaker (Built-in)
Power LED
1W x 2 Stereo, RMS
Blue (On)/ Amber (Standby)
VESA wall mount
Tilt
100 x 100mm
+20˚~-3˚
Kensington lock
Voltage rating
Power consumption
Yes
AC: 100~240V
Power On : < 55W, Standby: < 2W, Power Off: <1W
Temperature (Operating)
0˚C~40˚C
Temperature
-20˚C~+60˚C
(Non-operating)
Dimension (W x H x D)
513 mm x ꢀ05 mm x 210 mm (machine)
588 mm x ꢀ95 mm x 150 mm (package)
ꢀ.8 kg (Net) ; 7.0 kg (Gross)
Weight (Esti.)
Multi-languages
10 languages (English, German, Italian, French, Dutch,
Spanish, Russian, Traditional Chinese, Simplified
Chinese, Japanese)
Accessories
VGA cable, DVI cable, audio cable, power cord, quick
start guide, warranty card
Energy Star®, CB, CE, Gost-R, CCC, CSA, FCC, C-Tick,
Regulation approvals
BSMI, VCCI, TCO03, RoHS, WEEE, PSB
*Specifications are subject to change without notice.
3-8
Chapter 3: General Instruction
Specifications summary (VW222T)
Panel Type
TFT LCD
Panel size
22" (16:10) wide screen
WSXGA+ 1680 x 1050
0.282mm
Max. Resolution
Pixel pitch
Brightness (Typ.)
Brightness (Max.)
Contrast Ratio (Typ.)
Contrast Ratio (Max.)
Viewing angle(H/V) CR>10
Display colors
250cd/m2
300cd/m2
800:1
2000:1 (with ASCR ON)
170˚/160˚
16.7M
Response time
5ms
SPLENDID™ Video
Enhancement
Yes
SPLENDID™ selection
Auto adjustment
5 video preset modes (by hotkey)
Yes (by hotkey)
Color temperature selection 5 color temperatures
Skin-Tone selection
Digital input
3 skin-tones
DVI-D with HDCP
Analog input
Audio-in port
Colors
D-Sub
3.5 mm Mini-jack
Black
Speaker (Built-in)
Power LED
1W x 2 Stereo, RMS
Blue (On)/ Amber (Standby)
VESA wall mount
Tilt
100 x 100mm
+20˚~-3˚
Kensington lock
Voltage rating
Power consumption
Yes
AC: 100~240V
Power On : < 55W, Standby: < 2W, Power Off: <1W
Temperature (Operating)
0˚C~40˚C
Temperature
-20˚C~+60˚C
(Non-operating)
Dimension (W x H x D)
513 mm x ꢀ05 mm x 210 mm (machine)
588 mm x ꢀ95 mm x 150 mm (package)
ꢀ.8 kg (Net) ; 7.0 kg (Gross)
Weight (Esti.)
Multi-languages
10 languages (English, German, Italian, French, Dutch,
Spanish, Russian, Traditional Chinese, Simplified
Chinese, Japanese)
Accessories
VGA cable, DVI cable, power cord, quick start guide,
warranty card
Energy Star®, CB, CE, Gost-R, CCC, CSA, FCC, C-Tick,
Regulation approvals
BSMI, VCCI, TCO03, RoHS, WEEE, PSB
*Specifications are subject to change without notice.
ASUS VW202/VW222 Series LCD Monitor
3-9
Specifications summary (VW222S)
Panel Type
TFT LCD
Panel size
22" (16:10) wide screen
WSXGA+ 1680 x 1050
0.282mm
Max. Resolution
Pixel pitch
Brightness (Typ.)
Brightness (Max.)
Contrast Ratio (Typ.)
Contrast Ratio (Max.)
Viewing angle(H/V) CR>10
Display colors
250cd/m2
300cd/m2
800:1
2000:1 (with ASCR ON)
170˚/160˚
16.7M
Response time
2ms (Gray to Gray)
Yes
SPLENDID™ Video
Enhancement
SPLENDID™ selection
Auto adjustment
5 video preset modes (by hotkey)
Yes (by hotkey)
Color temperature selection 5 color temperatures
Skin-Tone selection
Analog input
Audio-in port
Colors
3 skin-tones
D-Sub
3.5 mm Mini-jack
Black
Speaker (Built-in)
Power LED
1W x 2 Stereo, RMS
Blue (On)/ Amber (Standby)
VESA wall mount
Tilt
100 x 100mm
+20˚~-3˚
Kensington lock
Voltage rating
Power consumption
Yes
AC: 100~240V
Power On : < 55W, Standby: < 2W, Power Off: <1W
Temperature (Operating)
0˚C~40˚C
Temperature
-20˚C~+60˚C
(Non-operating)
Dimension (W x H x D)
513 mm x ꢀ05 mm x 210 mm (machine)
588 mm x ꢀ95 mm x 150 mm (package)
ꢀ.8 kg (Net) ; 7.0 kg (Gross)
Weight (Esti.)
Multi-languages
10 languages (English, German, Italian, French, Dutch,
Spanish, Russian, Traditional Chinese, Simplified
Chinese, Japanese)
Accessories
VGA cable, audio cable, power cord, quick start guide,
warranty card
Energy Star®, CB, CE, Gost-R, CCC, CSA, FCC, C-Tick,
Regulation approvals
BSMI, VCCI, TCO03, RoHS, WEEE, PSB
*Specifications are subject to change without notice.
3-10
Chapter 3: General Instruction
Specifications summary (VW222D)
Panel Type
TFT LCD
Panel size
22" (16:10) wide screen
WSXGA+ 1680 x 1050
0.282mm
Max. Resolution
Pixel pitch
Brightness (Typ.)
Brightness (Max.)
Contrast Ratio (Typ.)
Contrast Ratio (Max.)
Viewing angle(H/V) CR>10
Display colors
250cd/m2
300cd/m2
800:1
2000:1 (with ASCR ON)
170˚/160˚
16.7M
Response time
5ms
SPLENDID™ Video
Enhancement
Yes
SPLENDID™ selection
Auto adjustment
5 video preset modes (by hotkey)
Yes (by hotkey)
Color temperature selection 5 color temperatures
Skin-Tone selection
Analog input
Colors
3 skin-tones
D-Sub
Black
Power LED
Blue (On)/ Amber (Standby)
VESA wall mount
Tilt
100 x 100mm
+20˚~-3˚
Kensington lock
Voltage rating
Power consumption
Yes
AC: 100~240V
Power On : < 55W, Standby: < 2W, Power Off: <1W
Temperature (Operating)
0˚C~40˚C
Temperature
-20˚C~+60˚C
(Non-operating)
Dimension (W x H x D)
513 mm x ꢀ05 mm x 210 mm (machine)
588 mm x ꢀ95 mm x 150 mm (package)
ꢀ.8 kg (Net) ; 7.0 kg (Gross)
Weight (Esti.)
Multi-languages
10 languages (English, German, Italian, French, Dutch,
Spanish, Russian, Traditional Chinese, Simplified
Chinese, Japanese)
Accessories
VGA cable, power cord, quick start guide, warranty card
Regulation approvals
Energy Star®, CB, CE, Gost-R, CCC, CSA, FCC, C-Tick,
BSMI, VCCI, TCO03, RoHS, WEEE, PSB
*Specifications are subject to change without notice.
ASUS VW202/VW222 Series LCD Monitor
3-11
3.3
Troubleshooting (FAQ)
Problem
Possible Solution
Power LED is not ON
• Press the
button to check if the monitor
is in the ON mode.
• Check if the power cord is properly
connected to the monitor and the power
outlet.
The power LED lights amber and there is no • Check if the monitor and the computer are
screen image
in the ON mode.
• Make sure the signal cable is properly
connected the monitor and the computer.
• Inspect the signal cable and make sure
none of the pins are bent.
• Connect the computer with another
available monitor to check if the computer
is properly working.
Screen image is too light or dark
• Adjust the Contrast and Brightness settings
via OSD.
Screen image is not centered or sized
properly
• Press the
button for two seconds to
automatically adjust the image.
• Adjust the H-Position or V-Position settings
via OSD.
Screen image bounces or a wave pattern is • Make sure the signal cable is properly
present in the image
connected to the monitor and the computer.
• Move electrical devices that may cause
electrical interference.
Screen image has color defects (white does • Inspect the signal cable and make sure that
not look white)
none of the pins are bent.
• Perform Reset via OSD.
• Adjust the R/G/B color settings or select the
Color Temperature via OSD.
Screen image is blurry or fuzzy
• Press the
button for two seconds to
automatically adjust the image (for VGA
mode only).
• Adjust the Phase and Clock settings via
OSD.
No sound or sound is low
• Ensure that the audio cable is properly
connected to the monitor and the computer
• Adjust the volume settings of both your
monitor and computer.
• Ensure that the computer sound card driver
is properly installed and activated.
3-12
Chapter 3: General Instruction
3.4
Supported operating modes
Standard
Resolution
Frequency
720 x ꢀ00
Horizontal
Frequency
31.ꢀ7KHz
Vertical
Frequency
70Hz
Pixel
28.32MHz
DOS
6ꢀ0 x ꢀ80
6ꢀ0 x ꢀ80
6ꢀ0 x ꢀ80
800 x 600
800 x 600
800 x 600
800 x 600
102ꢀ x 768
102ꢀ x 768
102ꢀ x 768
1280 x 960
1280 x 102ꢀ
1280 x 102ꢀ
1152 x 86ꢀ
1ꢀꢀ0 x 900
1600 x 1200
31.ꢀ7KHz
37.90KHz
37.50KHz
35.16KHz
37.90KHz
ꢀ8.10KHz
ꢀ6.90KHz
ꢀ8.ꢀ0KHz
56.50KHz
60.02KHz
60.00KHz
6ꢀ.00KHz
80.00KHz
67.50KHz
55.9ꢀKHz
75.00KHz
60Hz
72Hz
75Hz
56Hz
60Hz
72Hz
75Hz
60Hz
70Hz
75Hz
60Hz
60Hz
75Hz
75Hz
60Hz
60Hz
25.18MHz
31.50MHz
31.50MHz
36.00MHz
ꢀ0.00MHz
50.00MHz
ꢀ9.50MHz
65.00MHz
75.00MHz
78.75MHz
108.00MHz
108.00MHz
135.00MHz
108.00MHz
106.5MHz
162.00MHz
VGA
SVGA
XGA
SXGA
VESA
UXGA
1680 x 1050
65.29KHz
60Hz
1ꢀ6.25MHz
VESA (Primary)
* Modes not listed in the table may not be supported. For optimal resolution, we recommend that
you choose a mode listed in the table above.
ASUS VW202/VW222 Series LCD Monitor
3-13
3-1ꢀ
Chapter 3: General Instruction
|