Asus Computer Hardware P8H61 M LX2 User Manual

P8H61-M LX2  
P8H61-M LX2/CSM  
Contents  
iii  
Contents  
iv  
Notices  
Federal Communications Commission Statement  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two  
conditions:  
This device may not cause harmful interference, and  
This device must accept any interference received including interference that may cause  
undesired operation.  
This equipment has been tested and found to comply with the limits for a Class B digital  
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide  
reasonable protection against harmful interference in a residential installation. This  
equipment generates, uses and can radiate radio frequency energy and, if not installed  
and used in accordance with manufacturer’s instructions, may cause harmful interference  
to radio communications. However, there is no guarantee that interference will not occur  
in a particular installation. If this equipment does cause harmful interference to radio or  
television reception, which can be determined by turning the equipment off and on, the user  
is encouraged to try to correct the interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment to an outlet on a circuit different from that to which the receiver is  
connected.  
Consult the dealer or an experienced radio/TV technician for help.  
The use of shielded cables for connection of the monitor to the graphics card is required  
to assure compliance with FCC regulations. Changes or modifications to this unit not  
expressly approved by the party responsible for compliance could void the user’s authority  
to operate this equipment.  
Canadian Department of Communications Statement  
This digital apparatus does not exceed the Class B limits for radio noise emissions from  
digital apparatus set out in the Radio Interference Regulations of the Canadian Department  
of Communications.  
This class B digital apparatus complies with Canadian ICES-003.  
ASUS Recycling/Takeback Services  
ASUS recycling and takeback programs come from our commitment to the highest standards  
for protecting our environment. We believe in providing solutions for you to be able to  
responsibly recycle our products, batteries, other components as well as the packaging  
materials. Please go to http://csr.asus.com/english/Takeback.htm for the detailed recycling  
information in different regions.  
vi  
 
REACH  
Complying with the REACH (Registration, Evaluation, Authorisation, and Restriction of  
Chemicals) regulatory framework, we published the chemical substances in our products at  
DO NOT throw the motherboard in municipal waste. This product has been designed to  
enable proper reuse of parts and recycling. This symbol of the crossed out wheeled bin  
indicates that the product (electrical and electronic equipment) should not be placed in  
municipal waste. Check local regulations for disposal of electronic products.  
DO NOT throw the mercury-containing button cell battery in municipal waste. This symbol  
of the crossed out wheeled bin indicates that the battery should not be placed in municipal  
waste.  
Safety information  
Electrical safety  
To prevent electric shock hazard, disconnect the power cable from the electric outlet  
before relocating the system.  
When adding or removing devices to or from the system, ensure that the power cables  
for the devices are unplugged before the signal cables are connected. If possible,  
disconnect all power cables from the existing system before you add a device.  
Before connecting or removing signal cables from the motherboard, ensure that all  
power cables are unplugged.  
Seek professional assistance before using an adapter or extension cord. These devices  
could interrupt the grounding circuit.  
Ensure that your power supply is set to the correct voltage in your area. If you are not  
sure about the voltage of the electrical outlet you are using, contact your local power  
company.  
If the power supply is broken, do not try to fix it by yourself. Contact a qualified service  
technician or your retailer.  
Operation safety  
Before installing the motherboard and adding devices on it, carefully read all the manuals  
that came with the package.  
Before using the product, ensure that all cables are correctly connected and the power  
cables are not damaged. If you detect any damage, contact your dealer immediately.  
To avoid short circuits, keep paper clips, screws, and staples away from connectors,  
slots, sockets and circuitry.  
Avoid dust, humidity, and temperature extremes. Do not place the product in any area  
where it may become wet.  
Place the product on a stable surface.  
If you encounter technical problems with the product, contact a qualified service  
technician or your retailer.  
vii  
 
About this guide  
This user guide contains the information you need when installing and configuring the  
motherboard.  
How this guide is organized  
This guide contains the following parts:  
Chapter 1: Product introduction  
This chapter describes the features of the motherboard and the new technology it  
supports.  
Chapter 2: BIOS information  
This chapter tells how to change system settings through the BIOS Setup menus.  
Detailed descriptions of the BIOS parameters are also provided.  
Conventions used in this guide  
To ensure that you perform certain tasks properly, take note of the following symbols used  
throughout this manual.  
DANGER/WARNING: Information to prevent injury to yourself when trying to  
complete a task.  
CAUTION: Information to prevent damage to the components when trying to  
complete a task.  
IMPORTANT: Instructions that you MUST follow to complete a task.  
NOTE: Tips and additional information to help you complete a task.  
Where to find more information  
Refer to the following sources for additional information and for product and software  
updates.  
1.  
ASUS websites  
The ASUS website provides updated information on ASUS hardware and software  
products. Refer to the ASUS contact information.  
2.  
Optional documentation  
Your product package may include optional documentation, such as warranty flyers,  
that may have been added by your dealer. These documents are not part of the  
standard package.  
Typography  
Bold text  
Italics  
Indicates a menu or an item to select.  
Used to emphasize a word or a phrase.  
<Key>  
Keys enclosed in the less-than and greater-than sign means  
that you must press the enclosed key.  
Example: <Enter> means that you must press the Enter or  
Return key.  
<Key1>+<Key2>+<Key3>  
If you must press two or more keys simultaneously, the key  
names are linked with a plus sign (+).  
Example: <Ctrl>+<Alt>+<D>  
viii  
 
P8H61-M LX2 Series specifications summary  
CPU  
LGA1155 socket for Intel® Second Generation processors  
Supports 32nm CPU  
Supports Enhanced Intel® SpeedStep Technology (EIST)  
* Refer to www.asus.com for Intel® CPU support list.  
Chipset  
Memory  
Intel® H61 Express Chipset  
2 x DIMM, max. 8GB, DDR3 1333 / 1066 MHz, non-ECC,  
un-buffered memory  
Dual-channel memory architecture  
Vendors List).  
** When you install a total memory of 4GB capacity or more,  
Windows® 32-bit operating system may only recognize less  
than 3GB. We recommend a maximum of 3GB system memory  
if you are using a Windows® 32-bit operating system.  
Graphics  
Dual independent displays support: DVI-D and D-Sub  
Supports DVI with max. resolution up to 1920x1200 @60Hz  
Supports D-Sub with max. resolution up to 2048x1536 @75Hz  
Expansion slots  
Storage  
1 x PCI Express 2.0 x16 slot  
2 x PCI Express 2.0 x1 slots  
1 x PCI slot  
Intel® H61 Express Chipset:  
-
4 x Serial ATA 3.0 Gb/s connectors  
Realtek® 8111E PCIe Gigabit LAN controller  
LAN  
Audio  
VIA® VT1708S 8-channel* High Definition Audio CODEC  
-
Supports Multi-Streaming  
*
Use a chassis with HD audio module in the front panel to  
support an 8-channel audio output.  
USB  
Intel® H61 Express Chipset:  
-
10 x USB 2.0/1.1 ports (4 ports at the mid-board, 6 ports at  
the back panel)  
ASUS unique  
features  
GPU Boost  
ASUS Anti-Surge Protection  
ASUS EFI BIOS  
ASUS CrashFree BIOS 3  
ASUS EZ Flash 2  
ASUS MyLogo 2™  
(continued on the next page)  
ix  
 
P8H61-M LX2 Series specifications summary  
Rear panel ports  
1 x PS/2 keyboard / mouse combo port  
1 x DVI-D port  
1 x D-Sub port  
1 x LAN (RJ-45) port  
6 x USB 2.0/1.1 ports  
3 x Audio jacks  
Internal connectors/  
switches/ buttons  
2 x USB 2.0/1.1 connectors support additional 4 USB 2.0/1.1  
ports  
4 x SATA 3.0 Gb/s connectors  
1 x CPU fan connector  
1 x Chassis fan connector  
1 x Front panel audio connector  
1 x S/PDIF Out connector  
1 x COM connector  
1 x System panel connector  
1 x Speaker connector  
1 x 24-pin ATX power connector  
1 x 4-pin ATX 12V power connector  
1 x TPM connector (P8H61-M LX2/CSM only)  
BIOS features  
32 Mb Flash ROM, EFI BIOS, PnP, DMI v2.0, WfM 2.0,  
ACPI v2.0a, SM BIOS v2.6, Multi-language BIOS  
Manageability  
Accessories  
WOL, PXE, PME Wake Up, WOR by Ring  
2 x Serial ATA 3.0Gb/s cables  
1 x I/O shield  
1 x User Manual  
1 x Support DVD  
Support DVD  
Form factor  
Drivers  
ASUS utilities  
ASUS Update  
Anti-virus software (OEM version)  
MicroATX form factor: 9.6 in x 7.8 in (24.4 cm x 19.8 cm)  
* Specifications are subject to change without notice.  
x
Chapter 1  
Product introduction  
Thank you for buying an ASUS® P8H61-M LX2 Series motherboard!  
Before you start installing the motherboard, and hardware devices on it, check the items in  
your motherboard package. Refer to page x for the list of accessories.  
If any of the items is damaged or missing, contact your retailer.  
ASUS P8H61-M LX2 Series motherboards include P8H61-M LX2 and P8H61-M  
LX2/CSM two models. The layout varies with models. The layout illustrations in this user  
manual are for P8H61-M LX2/CSM only.  
1.1  
Before you proceed  
Take note of the following precautions before you install motherboard components or change  
any motherboard settings.  
Unplug the power cord from the wall socket before touching any component.  
Before handling components, use a grounded wrist strap or touch a safely grounded  
object or a metal object, such as the power supply case, to avoid damaging them due to  
static electricity.  
Hold components by the edges to avoid touching the ICs on them.  
Whenever you uninstall any component, place it on a grounded antistatic pad or in the  
bag that came with the component.  
Before you install or remove any component, ensure that the ATX power supply is  
switched off or the power cord is detached from the power supply. Failure to do so may  
cause severe damage to the motherboard, peripherals, or components.  
Standby Power LED  
The motherboard comes with a standby power LED that lights up to indicate that the system  
is ON, in sleep mode, or in soft-off mode. This is a reminder that you should shut down  
the system and unplug the power cable before removing or plugging in any motherboard  
component. The illustration below shows the location of the onboard LED.  
SB_PWR  
8 0ꢀꢁꢂ5ꢃ4@ꢄꢅ+;5  
ON  
OFF  
Standby Power Powered Off  
8 0ꢀꢁꢂ5ꢃ4@ꢄꢅ+;5ꢃ7VJWIZLꢃ4-,  
Chapter 1: Product introduction  
1-1  
 
1.2  
Motherboard overview  
Before you install the motherboard, study the configuration of your chassis to ensure that the  
motherboard fits into it.  
Ensure that you unplug the power cord before installing or removing the motherboard.  
Failure to do so can cause you physical injury and damage motherboard components.  
1.2.1  
Placement direction  
When installing the motherboard, ensure that you place it into the chassis in the correct  
orientation. The edge with external ports goes to the rear part of the chassis as indicated in  
the image below.  
1.2.2  
Screw holes  
Place six screws into the holes indicated by circles to secure the motherboard to the chassis.  
Do not overtighten the screws! Doing so can damage the motherboard.  
Place this side towards  
the rear of the chassis  
P8H61-M LX2/CSM  
1-2  
ASUS P8H61-M LX2 Series  
 
1.2.3  
Motherboard layout  
1
2
3
1
4
19.8cm(7.8in)  
CPU_FAN  
KB_USB56  
EPU  
5
TPM  
ATX12V  
ASM  
1442  
2
6
USB34  
LAN1_USB12  
AUDIO  
Lithium Cell  
CMOS Power  
CHA_FAN  
SATA3G_1  
SATA3G_2  
PCIEX16_1  
RTL  
8111E  
P8H61-M LX2/CSM  
4Mb  
BIOS  
PCIEX1_1  
PCIEX1_2  
Intel®  
H61  
asmedia  
ASM1083  
Super  
I/O  
SATA3G_3  
6
7
SB_PWR  
SATA3G_4  
PCI1  
VIA  
VT1708S  
SPEAKER  
F_PANEL  
CLRTC  
SPDIF_OUT  
COM1  
USB78  
USB910  
AAFP  
14  
13 12  
11  
10  
9
8
1.2.4  
Layout contents  
Connectors/Jumpers/Slots/LED  
Page  
Connectors/Jumpers/Slots/LED  
Page  
1.  
2.  
3.  
CPU and chassis fan connectors  
(4-pin CPU_FAN, 3-pin CHA_FAN)  
1-19 8.  
System panel connector (10-1 pin PANEL)  
1-21  
ATX power connectors (24-pin EATXPWR,  
4-pin ATX12V)  
1-18 9.  
Clear RTC RAM (3-pin CLRTC)  
1-15  
1-1  
Intel® LGA1155 CPU socket  
1-4  
1-9  
10. Standby power LED (SB_PWR)  
4.  
5.  
DDR3 DIMM slots  
11. USB connectors (10-1 pin USB78, USB910)  
1-19  
1-18  
TPM connector (20-1 pin TPM) (P8H61-M  
LX2/CSM only)  
1-22 12. Serial port connector (10-1 pin COM1)  
6.  
7.  
Intel® H61 Serial ATA 3.0Gb/s connectors  
(7-pin SATA3G_1/2/3/4)  
1-20 13. Digital audio connector (4-1 pin SPDIF_OUT) 1-20  
1-21 14 Front panel audio connector (10-1 pin AAFP) 1-17  
Speaker connector (4-pin SPEAKER)  
Chapter 1: Product introduction  
1-3  
 
1.3  
Central Processing Unit (CPU)  
The motherboard comes with a surface mount LGA1155 socket designed for the Intel®  
Second Generation processors.  
Refer to www.asus.com for Intel® CPU support list.  
Unplug all power cables before installing the CPU.  
Upon purchase of the motherboard, ensure that the PnP cap is on the socket and the  
socket contacts are not bent. Contact your retailer immediately if the PnP cap is missing,  
or if you see any damage to the PnP cap/socket contacts/motherboard components.  
ASUS will shoulder the cost of repair only if the damage is shipment/transit-related.  
Keep the cap after installing the motherboard. ASUS will process Return Merchandise  
Authorization (RMA) requests only if the motherboard comes with the cap on the  
LGA1155 socket.  
The product warranty does not cover damage to the socket contacts resulting from  
incorrect CPU installation/removal, or misplacement/loss/incorrect removal of the PnP  
cap.  
1.3.1  
Installing the CPU  
To install a CPU:  
1. Locate the CPU socket on the motherboard.  
8 0ꢀꢁꢂ5ꢃ4@ꢄꢅ+;5  
8 0ꢀꢁꢂ5ꢃ4@ꢄꢅ+;5ꢃ+8=ꢃ[WKSM\ꢃ4/)ꢁ  
2.  
Press the load lever with your thumb (A),  
and then move it to the right (B) until it is  
released from the retention tab.  
Load lever  
A
To prevent damage to the socket pins,  
do not remove the PnP cap unless  
you are installing a CPU.  
B
Retention tab  
1-4  
ASUS P8H61-M LX2 Series  
 
3.  
4.  
5.  
Lift the load lever in the direction of the  
arrow until the load plate is completely  
lifted.  
Load plate  
Remove the PnP cap from the CPU  
socket by lifting the tab only.  
PnP cap  
Position the CPU over the socket,  
ensuring that the gold triangle is on the  
bottom-left corner of the socket, and  
then fit the socket alignment keys into  
the CPU notches.  
CPU notches  
The CPU fits in only one correct  
orientation. DO NOT force the CPU  
into the socket to prevent bending  
the connectors on the socket and  
damaging the CPU!  
Gold  
triangle  
mark  
Alignment keys  
Chapter 1: Product introduction  
1-5  
6.  
Apply some Thermal Interface Material  
to the exposed area of the CPU that the  
heatsink will be in contact with, ensuring  
that it is spread in an even thin layer.  
Some heatsinks come with pre-  
applied thermal paste. If so, skip this  
step.  
The Thermal Interface Material is  
toxic and inedible. DO NOT eat it. If  
it gets into your eyes or touches your  
skin, wash it off immediately, and seek  
professional medical help.  
7.  
Close the load plate (A), and then push  
down the load lever (B), ensuring that  
the front edge of the load plate slides  
under the retention knob (C).  
B
A
C
8.  
Insert the load lever under the retention  
tab.  
1-6  
ASUS P8H61-M LX2 Series  
1.3.2  
Installing the CPU heatsink and fan  
The Intel® LGA1155 processor requires a specially designed heatsink and fan assembly to  
ensure optimum thermal condition and performance.  
When you buy a boxed Intel® processor, the package includes the CPU fan and  
heatsink assembly. If you buy a CPU separately, ensure that you use only Intel®-certified  
multi-directional heatsink and fan.  
Your Intel® LGA1155 heatsink and fan assembly comes in a push-pin design and  
requires no tool to install.  
Use an LGA1155-compatible CPU heatsink and fan assembly only. The LGA1155 socket  
is incompatible with the LGA775 and LGA1366 sockets in size and dimension.  
If you purchased a separate CPU heatsink and fan assembly, ensure that you have  
properly applied Thermal Interface Material to the CPU heatsink or CPU before you install  
the heatsink and fan assembly.  
Ensure that you have installed the motherboard to the chassis before you install the CPU  
fan and heatsink assembly.  
To install the CPU heatsink and fan:  
A
1.  
Place the heatsink on top of the installed  
CPU, ensuring that the four fasteners match  
the holes on the motherboard.  
B
B
A
Orient the heatsink and fan assembly  
such that the CPU fan cable is closest to  
the CPU fan connector.  
2.  
Push down two fasteners at a time in a  
diagonal sequence to secure the heatsink  
and fan assembly in place.  
1
1
A
B
B
A
The type of CPU heatsink and fan assembly may differ, but the installation steps and  
functions should remain the same. The illustration above is for reference only.  
Chapter 1: Product introduction  
1-7  
 
3.  
Connect the CPU fan cable to the connector on the motherboard labeled CPU_FAN.  
CPU_FAN  
8 0ꢀꢁꢂ5ꢃ4@ꢄꢅ+;5  
8 0ꢀꢁꢂ5ꢃ4@ꢄꢅ+;5ꢃ+8=ꢃNIVꢃKWVVMK\WZ  
Do not forget to connect the CPU fan connector! Hardware monitoring errors can occur if  
you fail to plug this connector.  
1.3.3  
Uninstalling the CPU heatsink and fan  
To uninstall the CPU heatsink and fan:  
1.  
2.  
3.  
Disconnect the CPU fan cable from the connector on the motherboard.  
Rotate each fastener counterclockwise.  
Pull up two fasteners at a time in a diagonal sequence to disengage the heatsink and  
fan assembly from the motherboard.  
A
A
B
B
A
B
B
A
1-8  
ASUS P8H61-M LX2 Series  
 
4.  
5.  
Carefully remove the heatsink and fan  
assembly from the motherboard.  
Rotate each fastener clockwise to ensure  
correct orientation when reinstalling.  
1.4  
System memory  
1.4.1  
Overview  
The motherboard comes with two Double Data Rate 3 (DDR3) Dual Inline Memory Modules  
(DIMM) sockets.  
A DDR3 module has the same physical dimensions as a DDR2 DIMM but is notched  
differently to prevent installation on a DDR2 DIMM socket. DDR3 modules are developed for  
better performance with less power consumption.  
The figure illustrates the location of the DDR3 DIMM sockets:  
Channel  
Sockets  
Channel A  
Channel B  
DIMM_A1  
DIMM_B1  
8 0ꢀꢁꢂ5ꢃ4@ꢄꢅ+;5  
8 0ꢀꢁꢂ5ꢃ4@ꢄꢅ+;5ꢃꢄꢆꢇꢂXQVꢃ,,:ꢈꢃ,155ꢃ  
Chapter 1: Product introduction  
1-9  
 
1.4.2  
Memory configurations  
You may install 512MB, 1GB, 2GB, and 4GB unbuffered non-ECC DDR3 DIMMs into the  
DIMM sockets.  
You may install varying memory sizes in Channel A and Channel B. The system maps  
the total size of the lower-sized channel for the dual-channel configuration. Any excess  
memory from the higher-sized channel is then mapped for single-channel operation.  
According to Intel CPU specification, DIMM voltage below 1.65V is recommended to  
protect the CPU.  
Always install DIMMs with the same CAS latency. For optimum compatibility, we  
recommend that you obtain memory modules from the same vendor.  
Due to the memory address limitation on 32-bit Windows® OS, when you install 4GB  
or more memory on the motherboard, the actual usable memory for the OS can be  
about 3GB or less. For effective use of memory, we recommend that you do any of the  
following:  
- Use a maximum of 3GB system memory if you are using a 32-bit Windows® OS.  
- Install a 64-bit Windows® OS when you want to install 4GB or more on the  
motherboard.  
This motherboard does not support DIMMs made up of 512Mb (64MB) chips or less.  
The default memory operation frequency is dependent on its Serial Presence Detect  
(SPD), which is the standard way of accessing information from a memory module.  
Under the default state, some memory modules for overclocking may operate at a  
lower frequency than the vendor-marked value. To operate at the vendor-marked or at a  
higher frequency, refer to section 2.4 Ai Tweaker menu for manual memory frequency  
adjustment.  
For system stability, use a more efficient memory cooling system to support a full  
memory load (2 DIMMs) or overclocking condition.  
P8H61-M LX2 Series Motherboard Qualified Vendors Lists (QVL)  
DDR3-1066 MHz capability  
DIMM socket support  
(Optional)  
SS/  
DS  
Chip  
Brand  
Vendors  
Part No.  
Size  
Chip NO.  
Timing  
Voltage  
1 DIMM  
2 DIMMs  
Crucial  
Crucial  
CT12864BA1067.8FF  
CT25664BA1067.16FF  
1GB  
2GB  
SS  
DS  
Micron  
Micron  
9GF22D9KPT  
9HF22D9KPT  
7
7
-
-
1.35V(low  
voltage)  
ELPIDA  
ELPIDA  
ELPIDA  
EBJ10UE8EDF0-AE-F  
EBJ11UD8BAFA-AE-E  
EBJ21UE8EDF0-AE-F  
1GB  
1GB  
2GB  
SS  
DS  
DS  
ELPIDA J1108EDSE-DJ-F  
Elpida J5308BASE-AC-E  
ELPIDA J1108EDSE-DJ-F  
KTC D1288JPNDPLD9U  
ELPIDA J1108BDSE-DJ-F  
-
-
-
-
1.35V(low  
voltage)  
KINGSTON KVR1066D3N7/1G  
KINGSTON KVR1066D3N7/2G  
KINGSTON KVR1066D3N7/4G  
1GB  
2GB  
4GB  
SS  
DS  
DS  
SS  
DS  
7
7
7
7
7
1.5V  
1.5V  
1.5V  
-
Hynix  
Micron  
Micron  
Micron  
Elixir  
-
H5TQ2G83AFR  
9GF22D9KPT  
9HF22D9KPT  
9BF27D9KPV  
N2CB1G80CN-BE  
-
Micron  
Micron  
OCZ  
MT8JTF12864AZ-1G1F1 1GB  
MT16JTF25664AZ-1G1F1 2GB  
-
OCZ3G1066LV4GK  
4GB(2 x 2GB) DS  
7-7-7-20 1.65V  
Elixir  
M2Y2G64CB8HC5N-BE  
M2Y2G64CBHA9N-BE  
M2Y2G64CBHC9N-BE  
2GB DIMM PC3-8500  
2GB  
2GB  
2GB  
2GB  
DS  
DS  
DS  
DS  
-
-
-
-
-
Elixir  
7-7-7-20  
Elixir  
Elixir  
Hynix  
-
-
-
Kingtiger  
H5TQ1G83AFP G7C  
1-10  
ASUS P8H61-M LX2 Series  
 
DDR3-1333 MHz capability  
DIMM socket  
support  
(Optional)  
SS/ Chip  
DS Brand  
Vendors  
Part No.  
Size  
Chip NO.  
Timing Voltage  
1 DIMM 2 DIMMs  
A-Data  
AD31333001GOU  
AD31333G001GOU  
AD31333002GOU  
AD31333G002GMU  
78.A1GC6.9L1  
1GB  
SS A-Data  
AD30908C8D-151C E0906  
-
-
A-Data  
3GB(3 x 1GB) SS  
-
-
8-8-8-24 1.65-1.85V  
A-Data  
2GB  
2GB  
2GB  
2GB  
1GB  
1GB  
DS A-Data  
DS  
AD30908C8D-151C E0903  
-
-
A-Data  
-
-
8-8-8-24 1.65-1.85V  
Apacer  
DS APACER  
DS Apacer  
AM5D5808DEWSBG  
-
-
-
Apacer  
78.A1GC6.9L1  
AM5D5808FEQSBG  
9
CORSAIR  
CORSAIR  
CORSAIR  
CORSAIR  
CORSAIR  
CORSAIR  
CORSAIR  
Crucial  
CM3X1024-1333C9DHX  
CM3X1024-1333C9  
TR3X3G1333C9 G  
TR3X3G1333C9 G  
CM3X1024-1333C9DHX  
SS  
SS  
-
-
-
-
-
9-9-9-24 1.60V  
9-9-9-24 1.60V  
9-9-9-24 1.50V  
9-9-9-24 1.50V  
-
3GB(3 x 1GB) SS  
3GB(3 x 1GB) SS  
-
-
1GB  
DS Corsair  
-
-
-
CMD24GX3M6A1333C9(XMP) 24GB(6x4GB) DS  
-
-
-
9-9-9-24 1.60V  
9-9-9-24 1.50V  
CMX8GX3M4A1333C9  
CT12864BA1339.8FF  
CT25664BA1339.16FF  
8GB(4 x 2GB) DS  
-
1GB  
2GB  
SS Micron  
DS Micron  
9FF22D9KPT  
9
9
-
-
Crucial  
9KF27D9KPT  
-
Crucial  
BL25664BN1337.16FF (XMP) 6GB(3 x 2GB) DS  
-
7-7-7-24 1.65V  
1.35V(low  
voltage)  
ELPIDA  
ELPIDA  
EBJ10UE8EDF0-DJ-F  
EBJ21UE8EDF0-DJ-F  
1GB  
2GB  
SS ELPIDA  
J1108EDSE-DJ-F  
J1108EDSE-DJ-F  
-
1.35V(low  
voltage)  
DS ELPIDA  
SS G.SKILL  
-
-
G.SKILL  
G.SKILL  
G.SKILL  
G.SKILL  
F3-10600CL8D-2GBHK(XMP) 1GB  
-
-
-
-
-
F3-10666CL7T-3GBPK(XMP) 3GB(3 x 1GB) SS  
F3-10666CL9T-3GBNQ 3GB(3 x 1GB) SS  
-
-
-
7-7-7-18 1.5~1.6V  
9-9-9-24 1.5~1.6V  
8-8-8-21 1.5-1.6V  
F3-10600CL8D-4GBHK(XMP) 4GB(2 x 2GB) DS  
F3-10666CL8D-  
4GB(2 x 2GB) DS