Asus Computer Hardware P5G41T M LX PLUS User Manual

P5G41T-M LX V2  
P5G41T-M LX PLUS  
Contents  
iii  
Contents  
iv  
Notices  
Federal Communications Commission Statement  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two  
conditions:  
This device may not cause harmful interference, and  
This device must accept any interference received including interference that may cause  
undesired operation.  
This equipment has been tested and found to comply with the limits for a Class B digital  
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide  
reasonable protection against harmful interference in a residential installation. This  
equipment generates, uses and can radiate radio frequency energy and, if not installed  
and used in accordance with manufacturer’s instructions, may cause harmful interference  
to radio communications. However, there is no guarantee that interference will not occur  
in a particular installation. If this equipment does cause harmful interference to radio or  
television reception, which can be determined by turning the equipment off and on, the user  
is encouraged to try to correct the interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment to an outlet on a circuit different from that to which the receiver is  
connected.  
Consult the dealer or an experienced radio/TV technician for help.  
The use of shielded cables for connection of the monitor to the graphics card is required  
to assure compliance with FCC regulations. Changes or modifications to this unit not  
expressly approved by the party responsible for compliance could void the user’s authority  
to operate this equipment.  
Canadian Department of Communications Statement  
This digital apparatus does not exceed the Class B limits for radio noise emissions from  
digital apparatus set out in the Radio Interference Regulations of the Canadian Department  
of Communications.  
This class B digital apparatus complies with Canadian ICES-003.  
REACH  
Complying with the REACH (Registration, Evaluation, Authorisation, and Restriction of  
Chemicals) regulatory framework, we published the chemical substances in our products at  
DO NOT throw the motherboard in municipal waste. This product has been designed to  
enable proper reuse of parts and recycling. This symbol of the crossed out wheeled bin  
indicates that the product (electrical and electronic equipment) should not be placed in  
municipal waste. Check local regulations for disposal of electronic products.  
DO NOT throw the mercury-containing button cell battery in municipal waste. This symbol  
of the crossed out wheeled bin indicates that the battery should not be placed in municipal  
waste.  
vi  
 
Safety information  
Electrical safety  
To prevent electric shock hazard, disconnect the power cable from the electric outlet  
before relocating the system.  
When adding or removing devices to or from the system, ensure that the power cables  
for the devices are unplugged before the signal cables are connected. If possible,  
disconnect all power cables from the existing system before you add a device.  
Before connecting or removing signal cables from the motherboard, ensure that all  
power cables are unplugged.  
Seek professional assistance before using an adapter or extension cord. These devices  
could interrupt the grounding circuit.  
Ensure that your power supply is set to the correct voltage in your area. If you are not  
sure about the voltage of the electrical outlet you are using, contact your local power  
company.  
If the power supply is broken, do not try to fix it by yourself. Contact a qualified service  
technician or your retailer.  
Operation safety  
Before installing the motherboard and adding devices on it, carefully read all the manuals  
that came with the package.  
Before using the product, ensure that all cables are correctly connected and the power  
cables are not damaged. If you detect any damage, contact your dealer immediately.  
To avoid short circuits, keep paper clips, screws, and staples away from connectors,  
slots, sockets and circuitry.  
Avoid dust, humidity, and temperature extremes. Do not place the product in any area  
where it may become wet.  
Place the product on a stable surface.  
If you encounter technical problems with the product, contact a qualified service  
technician or your retailer.  
About this guide  
This user guide contains the information you need when installing and configuring the  
motherboard.  
How this guide is organized  
This guide contains the following parts:  
Chapter 1: Product introduction  
This chapter describes the features of the motherboard and the new technology it  
supports.  
Chapter 2: BIOS information  
This chapter tells how to change system settings through the BIOS Setup menus.  
Detailed descriptions of the BIOS parameters are also provided.  
vii  
 
Conventions used in this guide  
To ensure that you perform certain tasks properly, take note of the following symbols used  
throughout this manual.  
DANGER/WARNING: Information to prevent injury to yourself when trying to  
complete a task.  
CAUTION: Information to prevent damage to the components when trying to  
complete a task.  
IMPORTANT: Instructions that you MUST follow to complete a task.  
NOTE: Tips and additional information to help you complete a task.  
Where to find more information  
Refer to the following sources for additional information and for product and software  
updates.  
1.  
ASUS websites  
The ASUS website provides updated information on ASUS hardware and software  
products. Refer to the ASUS contact information.  
2.  
Optional documentation  
Your product package may include optional documentation, such as warranty flyers,  
that may have been added by your dealer. These documents are not part of the  
standard package.  
Typography  
Bold text  
Italics  
Indicates a menu or an item to select.  
Used to emphasize a word or a phrase.  
<Key>  
Keys enclosed in the less-than and greater-than sign means  
that you must press the enclosed key.  
Example: <Enter> means that you must press the Enter or  
Return key.  
<Key1>+<Key2>+<Key3>  
If you must press two or more keys simultaneously, the key  
names are linked with a plus sign (+).  
Example: <Ctrl>+<Alt>+<D>  
viii  
P5G41T-M LX Series specifications summary  
CPU  
LGA775 socket for Intel® Core™2 Quad / Core™2 Extreme  
/ Core™2 Duo / Pentium® dual-core / Celeron® dual-core /  
Celeron® processors  
Compatible with Intel® 05B/05A/06 processors  
Supports Intel® 45nm multi-core CPU  
* Refer to www.asus.com for Intel® CPU support list.  
Chipset  
Northbridge: Intel® G41  
Southbridge: Intel® ICH7  
Front Side Bus  
Memory  
1333/1066/800 MHz  
Dual channel memory architecture  
-
2 x 240-pin DIMM sockets support unbuffered non-ECC  
1333(O.C.)/1066 MHz DDR3 memory modules  
Supports up to 8GB system memory  
-
* Refer to www.asus.com for the latest Memory QVL (Qualified  
Vendors Lists).  
** When you install a total memory of 4GB or more, Windows®  
32-bit operating system may only recognize less than 3GB.  
We recommend a maximum of 3GB system memory if you  
are using a Windows® 32-bit operating system.  
Graphics  
Integrated Intel® GMA X4500 GPU  
Supports RGB with max. resolution of 2048 x 1536 (@ 75Hz)  
Supports Microsoft® DirectX® 10  
Expansion slots  
Storage  
1 x PCI Express x16 slot  
1 x PCI Express x1 slot  
2 x PCI slots  
1 x Ultra DMA 100/66/33 connector  
4 x Serial ATA 3Gb/s ports  
LAN  
PCIe Gigabit LAN  
Audio  
Realtek® ALC887 8-channel* High Definition Audio CODEC  
* Use a chassis with HD audio module in the front panel to  
support an 8-channel audio output.  
USB  
Supports up to 8 USB 2.0/1.1 ports (4 ports at mid-board,  
4 ports at the back panel)  
ASUS unique features  
ASUS CrashFree BIOS 3  
ASUS AI NET 2  
ASUS Q-Fan  
ASUS EZ Flash 2  
ASUS MyLogo 2  
ASUS Anti-Surge Protection  
ASUS Turbo Key  
ASUS EPU-L  
(continued on the next page)  
ix  
 
P5G41T-M LX Series specifications summary  
Other features  
100% All High-quality Conductive Polymer Capacitors  
(P5G41T-M LX PLUS only)  
Back panel I/O ports  
1 x PS/2 keyboard port (purple)  
1 x PS/2 mouse port (green)  
1 x LPT port  
1 x COM port  
1 x VGA port  
1 x LAN (RJ-45) port  
4 x USB 2.0/1.1 ports  
3 x Audio jacks  
Internal connectors  
2 x USB 2.0/1.1 connectors support additional 4 USB 2.0/1.1  
ports  
1 x IDE connector  
4 x Serial ATA connectors  
1 x Front panel audio connector  
1 x System panel connector  
1 x S/PDIF Out connector  
1 x Internal speaker connector  
1 x CPU fan connector  
1 x Chassis fan connector  
1 x 24-pin EATX power connector  
1 x 4-pin ATX 12V power connector  
BIOS  
8Mb Flash ROM, AMI BIOS, PnP, DMI 2.0, WfM 2.0, ACPI 2.0a,  
SM BIOS 2.5  
Accessories  
1 x Ultra DMA 100/66/33 cable  
2 x Serial ATA cables  
1 x I/O shield  
1 x User Manual  
Support DVD  
Drivers  
ASUS utilities  
ASUS Update  
Anti-Virus software (OEM version)  
Form factor  
MicroATX form factor: 9.6 in x 7.9 in (24.4 cm x 20.1 cm)  
* Specifications are subject to change without notice.  
x
Chapter 1  
Product introduction  
1.1  
Welcome!  
Thank you for buying an ASUS® P5G41T-M LX Series motherboard!  
The motherboard delivers a host of new features and latest technologies, making it another  
standout in the long line of ASUS quality motherboards!  
Before you start installing the motherboard, and hardware devices on it, check the items in  
your package with the list below.  
1.2  
Package contents  
Check your motherboard package for the following items.  
Motherboard  
ASUS P5G41T-M LX Series motherboard  
Cables  
2 x Serial ATA cables  
1 x Ultra DMA 100/66/33 cable  
Accessories  
1 x I/O shield  
Application DVD  
Documentation  
ASUS motherboard support DVD  
User Manual  
P5G41T-M LX Series motherboards include P5G41T-M LX V2 and P5G41T-M LX PLUS  
two models. The package contents vary from models.  
If any of the items is damaged or missing, contact your retailer.  
1.3  
Special features  
1.3.1  
Product highlights  
Intel® Core™2 Extreme / Core™2 Quad / Core™2 Duo CPU  
support  
This motherboard supports Intel® LGA775 Core™ 2 Extreme / Core™  
2 Quad/ Core™ 2 Duo processors, which are excellent for multitasking,  
multimedia, and enthusiastic gamers with 1333/1066/800 MHz FSB.  
This motherboard also supports Intel® CPUs in the 45nm manufacturing  
process.  
ASUS P5G41T-M LX Series  
1-1  
 
Intel® G41 Chipset  
The Intel® G41 Express Chipset is designed to support dual-channel  
DDR3 1333 (overclocking)/1066 architecture, 1333/1066/800 Front  
Side Bus (FSB), PCIe 1.1, and mutli-core CPUs. It especially includes  
Intel® Fast memory bandwidth and reduces the latency of the memory  
accesses.  
Dual channel DDR3 1333 (O.C.)/1066 support  
This motherboard supports DDR3 memory that features data transfer  
rates of 1333 (O.C.)/1066 MHz providing great performance for 3D  
graphics and other memory-demanding applications.  
Serial ATA 3Gb/s technology  
This motherboard supports hard drives based on the Serial ATA (SATA)  
3Gb/s storage specifications, delivering enhanced scalability and  
doubling the bus bandwidth for high-speed data saving and retrieval.  
Gigabit LAN solution  
The onboard LAN controller is a highly integrated Gb LAN controller. It is  
enhanced with an ACPI management function to provide efficient power  
management for advanced operating systems.  
8-channel high definition audio  
Enjoy high-end sound quality on your PC! The onboard 8-channel High  
Definition Audio CODEC enables high-quality 192KHz/24-bit audio  
output, jack-sensing feature, and multi-streaming technology that  
simultaneously sends different audio streams to different destinations.  
You can now talk to your partners on the headphone while playing multi-  
channel network games.  
100% All High-quality Conductive Polymer Capacitors  
(P5G41T-M LX PLUS only)  
This motherboard uses all high-quality conductive polymer capacitors for  
durability, improved lifespan, and enhanced thermal capacity.  
1.3.2  
Innovative ASUS features  
ASUS EPU  
ASUS EPU is a unique power saving technology that detects the current  
system loadings and adjusts the power consumption in real time.  
Turbo Key  
ASUS Turbo Key allows you to turn the PC power button into  
an overclocking button. After you easy setup, Turbo Key boosts  
performances without interrupting ongoing work or games, simply through  
pressing the button.  
1-2  
Chapter 1: Product introduction  
 
ASUS Q-Fan  
ASUS Q-Fan technology intelligently adjusts the CPU fan speed  
according to system loading to ensure a quiet, cool, and efficient  
operation.  
ASUS Anti-Surge Protection  
This special design prevents expensive devices and the motherboard  
from damage caused by power surges from switching power supply  
(PSU).  
ASUS MyLogo2™  
This feature allows you to convert your favorite photo into a 256-color  
boot logo for a more colorful and vivid image on your screen.  
ASUS CrashFree BIOS 3  
ASUS CrashFree BIOS 3 is an auto-recovery tool that allows you to  
restore a corrupted BIOS file using the bundled support DVD or USB  
flash disk that contains the latest BIOS file.  
ASUS EZ Flash 2  
ASUS EZ Flash 2 is a utility that allows you to update the BIOS without  
using an OS-based utility.  
ASUS AI NET2  
ASUS AI NET2 remotely detects the cable connection immediately after  
turning on the system, and any faulty cable connections are reported  
back up to 100 meters at 1 meter accuracy.  
C.P.R. (CPU Parameter Recall)  
The BIOS C.P.R. feature automatically restores the CPU default settings  
when the system hangs due to overclocking failure. C.P.R. eliminates the  
need to open the system chassis and clear the RTC data. Simply shut  
down and reboot the system, and the BIOS automatically restores the  
CPU parameters to their default settings.  
ErP ready  
The motherboard is European Union´s Energy-related Products (ErP)  
ready, and ErP requires products to meet certain energy efficiency  
requirements in regards to energy consumptions. This is in line with  
ASUS vision of creating environment-friendly and energy-efficient  
products through product design and innovation to reduce carbon  
footprint of the product and thus mitigate environmental impacts.  
ASUS P5G41T-M LX Series  
1-3  
1.4  
Before you proceed  
Take note of the following precautions before you install motherboard components or change  
any motherboard settings.  
Unplug the power cord from the wall socket before touching any component.  
Before handling components, use a grounded wrist strap or touch a safely grounded  
object or a metal object, such as the power supply case, to avoid damaging them due to  
static electricity.  
Hold components by the edges to avoid touching the ICs on them.  
Whenever you uninstall any component, place it on a grounded antistatic pad or in the  
bag that came with the component.  
Before you install or remove any component, ensure that the ATX power supply is  
switched off or the power cord is detached from the power supply. Failure to do so may  
cause severe damage to the motherboard, peripherals, or components.  
Onboard LED  
The motherboard comes with a standby power LED that lights up to indicate that the system  
is ON, in sleep mode, or in soft-off mode. This is a reminder that you must shut down  
the system and unplug the power cable before removing or plugging in any motherboard  
component. The illustration below shows the location of the onboard LED.  
P5G41T-M LX PLUS Onboard LED  
1-4  
Chapter 1: Product introduction  
 
1.5  
Motherboard overview  
Before you install the motherboard, study the configuration of your chassis to ensure that the  
motherboard fits into it.  
Ensure that you unplug the power cord before installing or removing the motherboard.  
Failure to do so can cause you physical injury and damage motherboard components.  
1.5.1  
Placement direction  
When installing the motherboard, ensure that you place it into the chassis in the correct  
orientation. The edge with external ports goes to the rear part of the chassis as indicated in  
the image below.  
1.5.2  
Screw holes  
Place six screws into the holes indicated by circles to secure the motherboard to the chassis.  
Do not overtighten the screws! Doing so can damage the motherboard.  
Place this side towards  
the rear of the chassis  
ASUS P5G41T-M LX Series  
1-5  
 
1.5.3  
Motherboard layout  
ASUS P5G41T-M LX Series motherboards include P5G41T-M LX V2 and P5G41T-M LX  
PLUS two models. The layout varies with models. The layout illustrations in this user guide  
are for P5G41T-M LX PLUS only.  
20.1cm(7.9in)  
RTL  
8111E  
ICS  
9LRS954A4  
9
15  
14  
13  
12  
11  
10  
1.5.4  
Layout contents  
Connectors/Jumpers/Slots/LED  
Page  
Connectors/Jumpers/Slots/LED  
Page  
1-18  
1-24  
1. Keyboard power (3-pin KBPWR)  
1-19 9.  
Clear RTC RAM (3-pin CLRTC)  
2. ATX power connectors (24-pin EATXPWR,  
4-pin ATX12V)  
1-23 10. Serial ATA connectors (7-pin SATA1-4)  
3. USB device wake-up (3-pin USBPW1-4, 3-pin  
USBPW5-8)  
1-19 11. USB connectors (10-1 pin USB56, USB78)  
1-24  
4. CPU and chassis fan connectors  
(4-pin CPU_FAN, 3-pin CHA_FAN)  
1-25 12. System panel connector (10-1 pin F_PANEL) 1-26  
5. Intel LGA775 CPU socket  
6. DDR3 DIMM slots  
1-7  
13. Speaker connector (4-pin SPEAKER)  
1-26  
1-12 14. Front panel audio connector (10-1 pin AAFP) 1-21  
7. IDE connector (40-1 pin PRI_IDE)  
8. Onboard LED (SB_PWR)  
1-22 15. Digital audio connector (4-1 pin SPDIF_OUT) 1-25  
1-4  
1-6  
Chapter 1: Product introduction  
 
1.6  
Central Processing Unit (CPU)  
The motherboard comes with a surface mount LGA775 socket designed for the Intel®  
Core™2 Extreme / Core™2 Quad / Core™2 Duo / Pentium® dual-core / Celeron® dual-core /  
Celeron® processors  
Unplug all power cables before installing the CPU.  
Connect the CPU fan cable to the CPU_FAN connector and chassis fan cable to the  
CHA_FAN connector to ensure system stability.  
Upon purchase of the motherboard, ensure that the PnP cap is on the socket and the  
socket contacts are not bent. Contact your retailer immediately if the PnP cap is missing,  
or if you see any damage to the PnP cap/socket contacts/motherboard components.  
ASUS will shoulder the cost of repair only if the damage is shipment/transit-related.  
Keep the cap after installing the motherboard. ASUS will process Return Merchandise  
Authorization (RMA) requests only if the motherboard comes with the cap on the  
LGA775 socket.  
The product warranty does not cover damage to the socket contacts resulting from  
incorrect CPU installation/removal, or misplacement/loss/incorrect removal of the PnP  
cap.  
The motherboard supports Intel® LGA775 processors with the Intel® Enhanced Intel  
SpeedStep® Technology (EIST) and Hyper-Threading Technology.  
1.6.1  
Installing the CPU  
To install a CPU:  
1. Locate the CPU socket on the motherboard.  
P5G41T-M LX PLUS CPU socket 775  
Before installing the CPU, ensure that the cam box is facing towards you and the load lever  
is on your left.  
ASUS P5G41T-M LX Series  
1-7  
 
2.  
Press the load lever with your thumb  
(A), then move it to the left (B) until it is  
released from the retention tab.  
Retention tab  
A
To prevent damage to the socket  
pins, do not remove the PnP cap  
unless you are installing a CPU.  
B
Load lever  
3.  
4.  
Lift the load lever in the direction of the  
arrow to a 135º angle.  
PnP cap  
Load plate  
4B  
Lift the load plate with your thumb and  
forefinger to a 100º angle (4A), then  
push the PnP cap from the load plate  
window to remove (4B).  
4A  
3
5.  
Position the CPU over the socket,  
ensuring that the gold triangle is on the  
bottom-left corner of the socket then fit  
the socket alignment key into the CPU  
notch.  
CPU notch  
Gold  
triangle  
mark  
Alignment key  
1-8  
Chapter 1: Product introduction  
6.  
Apply some Thermal Interface Material  
to the exposed area of the CPU that the  
heatsink will be in contact with, ensuring  
that it is spread in an even thin layer.  
Some heatsinks come with  
pre-applied thermal paste. If so, skip  
this step.  
DO NOT eat the Thermal Interface Material. If it gets into your eyes or touches your skin,  
ensure that you wash it off immediately, and seek professional medical help.  
To prevent contaminating the paste, DO NOT spread the paste with your finger directly.  
7.  
Close the load plate (A), then push  
A
the load lever (B) until it snaps into the  
retention tab.  
B
ASUS P5G41T-M LX Series  
1-9  
1.6.2  
Installing the CPU heatsink and fan  
The Intel® LGA775 processor requires a specially designed heatsink and fan assembly to  
ensure optimum thermal condition and performance.  
When you buy a boxed Intel® processor, the package includes the CPU fan and  
heatsink assembly. If you buy a CPU separately, ensure that you use only Intel®-certified  
multi-directional heatsink and fan.  
Your Intel® LGA775 heatsink and fan assembly comes in a push-pin design and requires  
no tool to install.  
If you purchased a separate CPU heatsink and fan assembly, ensure that you have  
properly applied Thermal Interface Material to the CPU heatsink or CPU before you  
install the heatsink and fan assembly.  
Ensure that you have installed the motherboard to the chassis before you install the CPU  
fan and heatsink assembly.  
To install the CPU heatsink and fan:  
A
1.  
Place the heatsink on top of the installed  
CPU, ensuring that the four fasteners match  
the holes on the motherboard.  
B
B
A
Orient the heatsink and fan assembly  
such that the CPU fan cable is closest to  
the CPU fan connector.  
2.  
Push down two fasteners at a time in a  
diagonal sequence to secure the heatsink  
and fan assembly in place.  
1
1
A
B
B
A
The type of CPU heatsink and fan assembly may differ, but the installation steps and  
functions should remain the same. The illustration above is for reference only.  
1-10  
Chapter 1: Product introduction  
 
3.  
Connect the CPU fan cable to the connector on the motherboard labeled CPU_FAN.  
P5G41T-M LX PLUS CPU fan connector  
Do not forget to connect the CPU fan connector! Hardware monitoring errors can occur if  
you fail to plug this connector.  
1.6.3  
Uninstalling the CPU heatsink and fan  
To uninstall the CPU heatsink and fan:  
1.  
2.  
3.  
Disconnect the CPU fan cable from the connector on the motherboard.  
Rotate each fastener counterclockwise.  
Pull up two fasteners at a time in a diagonal sequence to disengage the heatsink and  
fan assembly from the motherboard.  
A
A
B
B
A
B
B
A
ASUS P5G41T-M LX Series  
1-11  
 
4.  
5.  
Carefully remove the heatsink and fan  
assembly from the motherboard.  
Rotate each fastener clockwise to ensure  
correct orientation when reinstalling.  
1.7  
System memory  
1.7.1  
Overview  
The motherboard comes with two Double Data Rate 3 (DDR3) Dual Inline Memory Modules  
(DIMM) sockets. The figure illustrates the location of the DDR3 DIMM sockets:  
Channel  
Sockets  
DIMM_A1  
DIMM_B1  
Channel A  
Channel B  
P5G41T-M LX PLUS 240-pin DDR3 DIMM sockets  
1-12  
Chapter 1: Product introduction  
 
1.7.2  
Memory configurations  
You may install 512MB, 1GB, 2GB, and 4GB unbuffered non-ECC DDR3 DIMMs into the  
DIMM sockets.  
You may install varying memory sizes in Channel A and Channel B. The system maps  
the total size of the lower-sized channel for the dual-channel configuration. Any excess  
memory from the higher-sized channel is then mapped for single-channel operation.  
Always install DIMMs with the same CAS latency. For optimum compatibility, it is  
recommended that you obtain memory modules from the same vendor.  
Due to the memory address limitation on 32-bit Windows® OS, when you install 4GB  
or more memory on the motherboard, the actual usable memory for the OS can be  
about 3GB or less. For effective use of memory, we recommend that you do any of the  
following:  
-
-
Use a maximum of 3GB system memory if you are using a 32-bit Windows® OS.  
Install a 64-bit Windows® OS when you want to install 4GB or more memory on  
the motherboard.  
This motherboard does not support DIMMs made up of 256 megabits (Mb) chips or less.  
The default memory operation frequency is dependent on its Serial Presence Detect  
(SPD), which is the standard way of accessing information from a memory module.  
Under the default state, some memory modules for overclocking may operate at a lower  
frequency than the vendor-marked value.  
For system stability, use a more efficient cooling system to support a full memory load (2  
DIMMs) or overclocking conditions.  
P5G41T-M LX Series Motherboard Qualified Vendors Lists (QVL)  
DDR3-1066 MHz capability  
DIMM socket  
support (Optional)  
SS/ Chip  
DS Brand  
Vendor  
Part No.  
Size  
Chip NO.  
Timing  
Voltage  
A*  
B*  
Crucial  
Crucial  
CT12864BA1067.8FF  
CT25664BA1067.16FF  
1024MB SS Micron  
2048MB DS Micron  
9GF22D9KPT  
9HF22D9KPT  
7
7
-
-
1.35V(low  
voltage)  
ELPIDA  
EBJ10UE8EDF0-AE-F  
1024MB SS ELPIDA  
J1108EDSE-DJ-F  
-
Elpida  
Elpida  
Elpida  
EBJ51UD8BAFA-AC-E  
EBJ51UD8BAFA-AE-E  
EBJ11UD8BAFA-AE-E  
512MB  
512MB  
SS Elpida  
SS Elpida  
J5308BASE-AC-E  
J5308BASE-AC-E  
J5308BASE-AC-E  
-
-
-
-
-
-
1024MB DS Elpida  
2048MB DS ELPIDA  
1.35V(low  
voltage)  
ELPIDA  
EBJ21UE8EDF0-AE-F  
J1108EDSE-DJ-F  
-
Kingston  
Kingston  
Micron  
KVR1066D3N7/1G  
KVR1066D3N7/2G  
1024MB SS Kingston  
2048MB DS Kingston  
D1288JEKAPGA7U  
D1288JEKAPGA7U  
9GF22D9KPT  
7
1.5V  
7
1.5V  
MT8JTF12864AZ-1G1F1 1024MB SS Micron  
MT16JTF25664AZ-1G1F1 2048MB DS Micron  
7
-
-
-
-
-
-
Micron  
9HF22D9KPT  
7
SAMSUNG M378B2873EH1-CF8  
SAMSUNG M378B5273BH1-CF8  
1024MB SS Samsung  
SEC 901 HCF8 K4B1G0846E  
-
4096MB DS SAMSUNG 846 K4B2G0846B-HCF8  
-
Elixir  
M2Y2G64CBHA9N-BE  
2GB DIMM PC3-8500  
2048MB DS  
-
-
7-7-7-20  
-
Kingtiger  
2048MB DS Hynix  
H5TQ1G83AFP G7C  
ASUS P5G41T-M LX Series  
1-13  
 
DDR3-1333 MHz (O.C.) capability  
DIMM socket  
support (Optional)  
SS/ Chip  
DS Brand  
Vendor  
Part No.  
Size  
Chip NO.  
Timing Voltage  
A*  
B*  
A-Data  
A-Data  
A-Data  
A-Data  
Corsair  
Corsair  
Corsair  
Corsair  
Corsair  
Corsair  
Corsair  
Corsair  
Crucial  
Crucial  
Crucial  
Crucial  
Crucial  
AD31333001GOU  
1024MB  
SS A-Data  
AD30908C8D-151C E0906  
-
-
AD31333G001GOU  
AD31333002GOU  
3072MB(Kit of 3) SS  
-
-
8-8-8-24 1.65-1.85V  
2048MB  
2048MB  
1024MB  
1024MB  
DS A-Data  
AD30908C8D-151C E0903  
-
-
AD31333G002GMU  
CM3X1024-1333C9DHX  
CM3X1024-1333C9  
TR3X3G1333C9 G  
DS  
SS  
SS  
-
-
-
-
-
-
-
8-8-8-24 1.65-1.85V  
9-9-9-24 1.60V  
-
-
-
-
3072MB(Kit of 3) SS  
3072MB(Kit of 3) SS  
3072MB(Kit of 3) SS  
-
9-9-9-24 1.50V  
9-9-9-24 1.50V  
TR3X3G1333C9 G  
-
TR3X3G1333C9  
-
9
-
1.5V  
CM3X1024-1333C9DHX  
CM3X2048-1333C9DHX  
TW3X4G1333C9 G  
CT12864BA1339.8FF  
BL12864TA1336.8SFB1  
CT25664BA1339.16FF  
1024MB  
2048MB  
DS Corsair  
-
-
-
DS  
-
-
-
-
4096MB(Kit of 2) DS  
1024MB  
2048MB(Kit of 2) SS  
2048MB DS Micron  
-
9-9-9-24 1.50V  
SS Micron  
9FF22D9KPT  
9
-
-
-
6-6-6-20 1.8V  
9KF27D9KPT  
9
-
BL25664ABA1336.16SFB1 4096MB(Kit of 2) DS  
BL25664BA1336.16SFB1 4096MB(Kit of 2) DS  
-
-
-
-
6-6-6-20 1.8V  
6-6-6-20 1.8V  
BL25664BN1337.16FF  
6144MB(Kit of 3) DS  
(XMP)  
Crucial  
ELPIDA  
ELPIDA  
-
-
7-7-7-24 1.65V  
1.35V(low  
EBJ10UE8EDF0-DJ-F  
EBJ21UE8EDF0-DJ-F  
1024MB  
2048MB  
SS ELPIDA  
DS ELPIDA  
J1108EDSE-DJ-F  
J1108EDSE-DJ-F  
-
-
voltage)  
1.35V(low  
voltage)  
G.SKILL  
G.SKILL  
G.SKILL  
G.SKILL  
G.SKILL  
G.SKILL  
G.SkiLL  
G.SKILL  
G.SKILL  
GEIL  
F3-10600CL8D-2GBHK  
F3-10600CL9D-2GBPK  
F3-10666CL7T-3GBPK  
F3-10666CL9T-3GBNQ  
F3-10600CL7D-2GBPI  
F3-10600CL9D-2GBNQ  
F3-10666CL8D-4GBHK  
F3-10666CL7T-6GBPK  
F3-10666CL9T-6GBNQ  
DDR3-1333 CL9-9-9-24  
GV34GB1333C7DC  
1024MB  
1024MB  
SS G.SKILL  
SS G.SKILL  
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
3072MB(Kit of 3) SS  
3072MB(Kit of 3) SS  
-
-
7-7-7-18 1.5~1.6V  
9-9-9-24 1.5~1.6V  
1024MB  
1024MB  
DS G.SKILL  
DS G.SKILL  
-
-
-
-
4096MB(Kit of 2) DS  
6144MB(Kit of 3) DS  
6144MB(Kit of 3) DS  
-
-
-
-
-
8-8-8-21 1.5-1.6V  
7-7-7-18 1.5~1.6V  
9-9-9-24 1.5V~1.6V  
1024MB  
2048MB  
SS  
DS  
9
-
GEIL  
7-7-7-24 1.5V  
1.3V(low  
voltage)  
GEIL  
GG34GB1333C9DC  
4096MB(Kit of 2) DS GEIL  
6144MB(Kit of 3) DS  
GL1L128M88BA12N  
9-9-9-24  
GEIL  
DDR3-1333 CL9-9-9-24  
FLFD45F-B8MF9  
-
-
9
-
1.5V  
Kingmax  
Kingmax  
Kingmax  
Kingmax  
Kingston  
Micron  
Micron  
OCZ  
1024MB  
1024MB  
2048MB  
2048MB  
2048MB  
1024MB  
SS Micron  
SS Micron  
DS Micron  
DS Micron  
DS Qimonda  
SS Micron  
DS Micron  
8HD22D9JNM  
-
FLFD45F-B8MH9 MAES  
FLFE85F-B8MF9  
9CF22D9KPT  
-
-
8HD22D9JNM  
-
-
FLFE85F-B8MH9 MEES  
KVR1333D3N9/2G  
9GF27D9KPT  
-
-
IDSH1G-03A1F1C-13H  
-
1.5V  
MT8JTF12864AZ-1G4F1  
9FF22D9KPT  
9
9
-
-
MT18JTF25664AZ-1G4F1 2048MB  
OCZ3P13332GK  
9KF27D9KPT  
2048MB(Kit of 2) SS  
-
-
-
-
-
-
-
-
-
-
-
7-7-7-20 1.8V  
OCZ  
OCZ3X1333LV3GK(XMP) 3072MB(Kit of 3) SS  
-
-
-
1.6V  
1.7V  
OCZ  
OCZ3G13334GK  
4096MB(Kit of 2) DS  
4096MB(Kit of 2) DS  
4096MB(Kit of 2) DS  
4096MB(Kit of 2) DS  
4096MB(Kit of 2) DS  
6144MB(Kit of 3) DS  
6144MB(Kit of 3) DS  
-
OCZ  
OCZ3P13334GK  
-
7-7-7-20 1.8V  
7-7-7-20 1.65V  
6-5-5-20 1.85V  
7-7-7-20 1.75V  
9-9-9-20 1.65V  
7-7-7-20 1.65V  
8-8-8-20 1.60V  
OCZ  
OCZ3P1333LV4GK  
OCZ3RPX1333EB4GK  
OCZ3X13334GK(XMP)  
OCZ3G1333LV6GK  
OCZ3P1333LV6GK  
-
OCZ  
-
OCZ  
-
OCZ  
-
OCZ  
-
OCZ  
OCZ3X1333LV6GK(XMP) 6144MB(Kit of 3) DS  
AL7F8G73D-DG1 1024MB  
-
PSC  
SS PSC  
A3P1GF3DGF928M9B05  
-
-
(continued on the next page)  
1-14  
Chapter 1: Product introduction