A8R32-MVP
Deluxe
Contents
Notices............................................................................................... vii
Safety information ............................................................................ viii
About this guide ................................................................................. ix
A8R32-MVP Deluxe specifications summary ...................................... xi
Chapter 1:
Product introduction
1.1
1.2
1.3
Welcome!.............................................................................. 1-1
Package contents ................................................................. 1-1
Special features.................................................................... 1-2
1.3.1
1.3.2
Product highlights................................................... 1-2
Innovative ASUS features ....................................... 1-4
Chapter 2:
Hardware information
2.1
Before you proceed .............................................................. 2-1
2.2
Motherboard overview.......................................................... 2-2
2.2.1
2.2.2
2.2.3
2.2.4
Placement direction ................................................ 2-2
Screw holes ............................................................ 2-2
Motherboard layout ................................................ 2-3
Layout Contents..................................................... 2-4
2.3
2.4
Central Processing Unit (CPU) .............................................. 2-7
2.3.1
2.3.2
Installing the CPU.................................................... 2-7
Installing the heatsink and fan................................ 2-8
System memory .................................................................2-11
2.4.1
2.4.2
2.4.3
2.4.4
Overview...............................................................2-11
Memory Configurations.........................................2-12
Installing a DDR DIMM ...........................................2-14
Removing a DDR DIMM ..........................................2-14
2.5
Expansion slots...................................................................2-15
2.5.1
2.5.2
2.5.3
2.5.4
2.5.5
2.5.6
Installing an expansion card..................................2-15
Configuring an expansion card..............................2-15
Interrupt assignments ..........................................2-16
PCI slots................................................................2-17
PCI Express x1 slot ...............................................2-17
Two PCI Express x16 slots ...................................2-17
iii
Contents
2.6
2.7
Jumper ...............................................................................2-19
Connectors .........................................................................2-20
2.7.1
2.7.2
Rear panel connectors ..........................................2-20
Internal connectors...............................................2-22
Chapter 3:
Powering up
3.1
Starting up for the first time................................................ 3-1
3.2
Powering off the computer .................................................. 3-2
3.2.1
3.2.2
Using the OS shut down function ........................... 3-2
Using the dual function power switch .................... 3-2
Chapter 4:
BIOS setup
4.1
Managing and updating your BIOS ........................................ 4-1
4.1.1
4.1.2
4.1.3
4.1.4
4.1.5
ASUS Update utility ................................................ 4-1
Creating a bootable floppy disk.............................. 4-4
ASUS EZ Flash utility .............................................. 4-5
AFUDOS utility ........................................................ 4-6
ASUS CrashFree BIOS 2 utility ................................ 4-9
4.2
BIOS setup program ...........................................................4-11
4.2.1
4.2.2
4.2.3
4.2.4
4.2.5
4.2.6
4.2.7
4.2.8
4.2.9
BIOS menu screen.................................................4-12
Menu bar...............................................................4-12
Navigation keys ....................................................4-12
Menu items ...........................................................4-13
Sub-menu items ...................................................4-13
Configuration fields ..............................................4-13
Pop-up window .....................................................4-13
Scroll bar ..............................................................4-13
General help ..........................................................4-13
4.3
Main menu ..........................................................................4-14
4.3.1
4.3.2
4.3.3
4.3.4
4.3.5
System Time.........................................................4-14
System Date .........................................................4-14
Legacy Diskette A ................................................4-14
Language ..............................................................4-14
Primary, Secondary, Third,
and Fourth IDE Master/Slave ................................4-15
4.3.6
4.3.7
Storage Configuration ..........................................4-16
System Information ..............................................4-17
i v
Contents
4.4
Advanced menu..................................................................4-18
4.4.1
4.4.2
4.4.3
4.4.4
4.4.5
4.4.6
4.4.7
JumperFree Configuration ....................................4-18
CPU Configuration.................................................4-22
Chipset Configuration ...........................................4-27
Onboard Devices Configuration ............................4-30
PCI PnP .................................................................4-32
LAN Cable Status .................................................4-33
USB Configuration.................................................4-33
4.5
Power menu........................................................................4-35
4.5.1
4.5.2
4.5.3
4.5.4
4.5.5
4.5.6
Suspend Mode ......................................................4-35
Repost Video on S3 Resume ................................4-35
ACPI 2.0 Support..................................................4-35
ACPI APIC Support ................................................4-35
APM Configuration ................................................4-36
Hardware Monitor .................................................4-38
4.6
4.7
Boot menu ..........................................................................4-40
4.6.1
4.6.2
4.6.3
Boot Device Priority..............................................4-41
Boot Settings Configuration .................................4-42
Security ................................................................4-43
Exit menu ...........................................................................4-45
Chapter 5:
Software support
5.1
Installing an operating system ............................................. 5-1
5.2
Support CD information........................................................ 5-1
5.2.1
5.2.2
5.2.3
5.2.4
5.2.5
5.2.6
5.2.7
Running the support CD ......................................... 5-1
Drivers menu .......................................................... 5-2
Utilities menu.......................................................... 5-4
Make Disk menu...................................................... 5-6
Manuals menu ......................................................... 5-7
ASUS Contact information...................................... 5-8
Other information ................................................... 5-8
v
Contents
5.3
Software information .........................................................5-10
5.3.1
5.3.2
5.3.3
5.3.4
5.3.5
ASUS MyLogo2™ ..................................................5-10
AI Net 2 ................................................................5-12
ASUS PC Probe II...................................................5-13
Cool ‘n’ Quiet™ Technology ..................................5-19
Audio configuration ..............................................5-21
5.4
5.5
RAID configurations ............................................................5-26
5.4.1
5.4.2
5.4.3
Installing hard disks ..............................................5-27
ULI® RAID configurations ......................................5-27
Silicon Image® RAID configurations.......................5-35
Creating a RAID driver disk .................................................5-42
Chapter 6:
ATI CrossFire™ technology support
6.1
6.2
6.3
Overview............................................................................... 6-1
Hardware installation ............................................................ 6-2
Software information ........................................................... 6-5
6.3.1
6.3.2
Installing the device drivers.................................... 6-5
Using the Catalyst™ Control Center ....................... 6-7
v i
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
•
•
This device may not cause harmful interference, and
This device must accept any interference received including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with
manufacturer’s instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the graphics
card is required to assure compliance with FCC regulations. Changes or
modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate
this equipment.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus set out in the Radio Interference
Regulations of the Canadian Department of Communications.
This class B digital apparatus complies with Canadian
ICES-003.
vii
Safety information
Electrical safety
•
•
To prevent electrical shock hazard, disconnect the power cable from
the electrical outlet before relocating the system.
When adding or removing devices to or from the system, ensure that
the power cables for the devices are unplugged before the signal cables
are connected. If possible, disconnect all power cables from the existing
system before you add a device.
•
•
•
Before connecting or removing signal cables from the motherboard,
ensure that all power cables are unplugged.
Seek professional assistance before using an adapter or extension cord.
These devices could interrupt the grounding circuit.
Make sure that your power supply is set to the correct voltage in your
area. If you are not sure about the voltage of the electrical outlet you
are using, contact your local power company.
•
If the power supply is broken, do not try to fix it by yourself. Contact a
qualified service technician or your retailer.
Operation safety
•
Before installing the motherboard and adding devices on it, carefully read
all the manuals that came with the package.
•
Before using the product, make sure all cables are correctly connected
and the power cables are not damaged. If you detect any damage,
contact your dealer immediately.
•
•
To avoid short circuits, keep paper clips, screws, and staples away from
connectors, slots, sockets and circuitry.
Avoid dust, humidity, and temperature extremes. Do not place the
product in any area where it may become wet.
•
•
Place the product on a stable surface.
If you encounter technical problems with the product, contact a qualified
service technician or your retailer.
The symbol of the crossed out wheeled bin indicates that the product
(electrical and electronic equipment) should not be placed in municipal
waste. Please check local regulations for disposal of electronic products.
viii
About this guide
This user guide contains the information you need when installing and
configuring the motherboard.
How this guide is organized
This guide contains the following parts:
•
Chapter 1: Product introduction
This chapter describes the features of the motherboard and the new
technology it supports.
•
Chapter 2: Hardware information
This chapter lists the hardware setup procedures that you have to
perform when installing system components. It includes description of
the switches, jumpers, and connectors on the motherboard.
•
•
Chapter 3: Powering up
This chapter describes the power up sequence, the vocal POST
messages, and ways of shutting down the system.
Chapter 4: BIOS setup
This chapter tells how to change system settings through the BIOS
Setup menus. Detailed descriptions of the BIOS parameters are also
provided.
•
•
Chapter 5: Software support
This chapter describes the contents of the support CD that comes
with the motherboard package.
Chapter 6: ATI CrossFire™ technology support
This chapter tells how to install ATI CrossFire™ graphics cards.
Where to find more information
Refer to the following sources for additional information and for product
and software updates.
1 . ASUS websites
The ASUS website provides updated information on ASUS hardware
and software products. Refer to the ASUS contact information.
2 . Optional documentation
Your product package may include optional documentation, such as
warranty flyers, that may have been added by your dealer. These
documents are not part of the standard package.
i x
Conventions used in this guide
To make sure that you perform certain tasks properly, take note of the
following symbols used throughout this manual.
DANGER/WARNING: Information to prevent injury to yourself
when trying to complete a task.
CAUTION: Information to prevent damage to the components
when trying to complete a task.
IMPORTANT: Instructions that you MUST follow to complete a
task.
NOTE: Tips and additional information to help you complete a
task.
Typography
Bold text
Italics
Indicates a menu or an item to select.
Used to emphasize a word or a phrase.
<Key>
Keys enclosed in the less-than and greater-than sign means
that you must press the enclosed key.
Example: <Enter> means that you must press the Enter or
Return key.
<Key1+Key2+Key3>
If you must press two or more keys simultaneously, the
key names are linked with a plus sign (+).
Example: <Ctrl+Alt+D>
Command
Means that you must type the command exactly as shown,
then supply the required item or value enclosed in
brackets.
Example: At the DOS prompt, type the command line:
afudos /i[filename]
afudos /iA8R32-MVP.ROM
x
A8R32-MVP Deluxe specifications summary
CPU
Socket 939 for AMD Athlon™ 64FX/Athlon™ 64 X2/
Athlon™ 64/Opteron processor
AMD64 architecture enables simultaneous 32- and
64-bit computing
Supports AMD Cool ‘n’ Quiet™ Technology
Supports AMD HyperTransport™ Technology
Chipset
ATI CrossFire™ Xpress 3200/ULi M1575
2000/1600 MT/s
System bus
Memory
Dual-channel memory architecture
4 x 184-pin DIMM sockets support up to 4 GB
unbufferred ECC/non-ECC 400/333/266 MHz DDR
memory modules
Expansion slots
2 x PCI Express™ x16 slots with CrossFire support at full
x16, x16 mode
1 x PCI Express™ x1 slot
3 x PCI slots
CrossFire™
Storage
Supports ATI CrossFire™ graphics cards (both at x16
mode)
ULi M1575 Southbridge supports:
- 2 x IDE connectors for up to four Ultra DMA
133/100/66/33 hard disks
- 4 x Serial ATA I/II 3.0 Gb/s hard disks with RAID 0,
RAID 1, RAID 0+1, RAID 5, and JBOD configuration
Silicon Image® 3132 SATA controller supports:
- 1 x Internal Serial ATA 3 Gb/s hard disk
- 1 x External Serial ATA hard disk (SATA On-the-Go)
- RAID 0 and RAID 1 configuration
High Definition
Audio
Realtek® ALC882 8-channel High Definition Audio (HD
Audio) CODEC
Supports Multi-streaming and Universal Audio Jack
Coaxial / Optical S/PDIF Out ports on the rear panel
LAN
Marvell® 88E8001 Gigabit LAN controller, featuring
AI NET2
Marvell® 88E8053 PCIe Gigabit LAN Controller, featuring AI
NET2
IEEE 1394a
T1 1394a controller supports:
- 2 x IEEE 1394a connectors at mid-board
USB
Supports up to 8 USB 2.0/1.1 ports
BIOS features
8 Mb Flash ROM, AMI BIOS, PnP, DMI2.0, SM BIOS 2.3,
WfM2.0
(continued on the next page)
x i
A8R32-MVP Deluxe specifications summary
ASUS AI Life
features
Stack Cool 2
ASUS SATA On-the-Go (External Serial ATA port on the
rear panel)
Other ASUS
ASUS MyLogo2™
special features
ASUS Multi-language BIOS
ASUS CrashFree BIOS 2
ASUS AI NET 2
ASUS Q-Fan2 Technology
ASUS EZ Flash
Overclocking
Intelligent overclocking tools:
- AI NOS™ (Non-delay Overclocking System)
- AI Overclocking (intelligent CPU frequency tuner)
- ASUS PEG Link (automatic performance tuning for
single/dual graphics cards)
Precision Tweaker supports:
- DIMM voltage: 12-step DRAM voltage control
- Core voltage: Adjustable CPU voltage at 0.025 V
increment
- Northbridge voltage: Adjustable voltage at 0.1 V
increment for core power, HT bus, and PCI Express
bus
Stepless Frequency Selection(SFS) allows:
- FSB tuning from 200 MHz to 400 MHz at 1 MHz increment
- PCI Express frequency tuning from 100 MHz to
150 MHz at 1 MHz increment
Overclocking protection:
- ASUS C.P.R. (CPU Parameter Recall)
Rear panel
1 x PS/2 mouse port
1 x PS/2 keyboard port
1 x Parallel port
2 x LAN (RJ-45) ports
4 x USB 2.0/1.1 ports
1 x Coaxial S/PDIF Out port
1 x Optical S/PDIF Out port
1 x External Serial ATA port
8-Channel audio ports
Manageabiity
WfM 2.0, DMI 2.0, WOL by PME, WOR by PME, chassis
intrusion, PXE, and RPL
Internal
1 x Floppy disk drive connector
2 x IDE connectors
connectors
1 x CPU fan connector
2 x Chassis fan connector
1 x Power fan connector
2 x IEEE 1394a connectors
5 x Serial ATA connectors
(continued on the next page)
xii
A8R32-MVP Deluxe specifications summary
Internal
2 x USB 2.0 connectors for four additional USB 2.0
ports
connectors
1 x 24-pin EATX power connector
1 x 4-pin ATX 12 V power connector
1 x GAME/MIDI connector
1 x CD-in connector
1 x COM connector
1 x Chassis intrusion connector
1 x Front panel High Definition Audio connector
1 x System panel connector
Support CD
contents
Drivers
ASUS PC Probe II
ASUS Update
Anti-virus software (OEM version)
Form factor
ATX form factor: 12 in x 9.6 in (30.5 cm x 24.4 cm)
*Specifications are subject to change without notice.
xiii
xiv
This chapter describes the
motherboard features and the new
technologies it supports
Product
1
information
Chapter summary
1
1.1
1.2
1.3
Welcome!.............................................................................. 1-1
Package contents ................................................................. 1-1
Special features.................................................................... 1-2
ASUS A8R32-MVP DELUXE
1.1 Welcome!
Thank you for buying an ASUS® A8R32-MVP Deluxe
motherboard!
The motherboard delivers a host of new features and latest technologies,
making it another standout in the long line of ASUS quality motherboards!
Before you start installing the motherboard, and hardware devices on it,
check the items in your package with the list below.
1.2 Package contents
Check your motherboard package for the following items.
Motherboard
Cables
ASUS A8R32-MVP Deluxe motherboard
1 x Floppy disk drive signal cable
1 x IDE cable
1 x Ultra DMA cable 133/100/66 cable
5 x Serial ATA cables
1 x 1-port Serial ATA power cable
2 x 2-port Serial ATA power cables
1 x 2-port IEEE 1394a cable
Accessories
1 x COM port module
I/O shield
1 x 2-port USB 2.0/Game module
Application CDs ASUS motherboard support CD
Documentation User guide
If any of the above items is damaged or missing, contact your retailer.
ASUS A8R32-MVP DELUXE
1-1
1.3 Special features
1.3.1 Product highlights
Latest processor technology
The motherboard comes with a 939-pin surface mount, Zero Insertion
Force (ZIF) socket that supports AMD Athlon™ 64/Athlon™ 64 FX/Athlon™
64 X2 processors. With an integrated low-latency high-bandwidth memory
controller and a highly-scalable HyperTransport™ technology-based system
bus, the motherboard provides a powerful platform for your diverse
computing needs, increased office productivity, and enhanced digital media
experience. See page 2-6.
ATI CrossFire™ Xpress 3200
The motherboard features ATI CrossFire™ Xpress 3200 support, delivering
improved overclocking and optimal PCI Express device performance. The
combined multi-GPU power boosts image quality and rendering speed for
the highest quality images. With its optimized peer-to-peer and general link
performance GPU sharing, you are a step ahead in graphics and gaming
effects. The chipset allows higher antialiasing, anisotropic filtering, sharing,
and texture settings. The ATI CrossFire™ Xpress 3200 also comes with the
ATI Catalyst™ Control Center that allows you to get real-time 3D-rendered
previews of adjustments to your display configurations and advanced 3D
settings.
PCI Express™ interface
The motherboard fully supports PCI Express, the latest I/O interconnect
technology that speeds up the PCI bus. PCI Express features point-to-point
serial interconnections between devices and allows higher clockspeeds by
carrying data in packets. This high speed interface is software compatible
with existing PCI specifications. See page 2-17 for details.
Serial ATA 3Gb/s technology
The motherboard supports the Serial ATA II 3 Gb/s technology through the
Serial ATA interfaces and the ULI M1575 Southbridge. The Serial ATA II 3
Gb/s specification provides twice the bandwidth of the current Serial ATA
products with a host of new features, including Native Command Queueing
(NCQ), and Power Management (PM) Implementation Algorithm. Serial ATA
allows for thinner, more flexible cables with lower pin count, reduced voltage
requirement. See page 2-23 for details.
1-2
Chapter 1: Product introduction
8-channel high definition audio
Onboard is the Realtek® ALC882 High Definition Audio 8-channel audio
CODEC. This CODEC is fully-compliant with Intel® High Definition Audio
standard (192 KHz, 24-bit audio). With the CODEC, 8-channel audio ports,
and S/PDIF interfaces, you can connect your computer to home theater
decoders to produce crystal-clear digital audio.
The Realtek® ALC882 CODEC comes with a software application that
features jack detection to monitor the plugging status of each jack,
impedance sensing to determine audio device classes, and pre-defined
equalization for various audio devices. See page 2-20 for details.
Dual RAID solution
Onboard RAID controllers provide the motherboard with dual-RAID
functionality that allows you to select the best RAID solution using Serial
ATA devices.
The ULi M1575 Southbridge allows RAID 0, RAID 1, RAID 0+1, and JBOD
configuration for four SATA 3Gb/s. See page 2-23 for details.
The Silicon Image® 3132 controller supports two additional Serial ATA
3Gb/s connectors and allows RAID 0 and RAID 1 configurations through the
internal and external Serial ATA ports. See page 2-25 for details.
Dual Gigabit LAN solution
The motherboard comes with dual Gigabit LAN controllers to provide the total
solution for your networking needs. These network controllers use both PCI
Express and PCI segments to provide faster data bandwidth for your wired or
wireless Internet, LAN, and file sharing requirements. See page 2-21 for
details.
IEEE 1394a support
The IEEE 1394a interface provides high-speed and flexible PC connectivity
to a wide range of peripherals and devices compliant to IEEE 1394a
standards. The IEEE 1394a interface allows up to 400 Mbps transfer rates
through simple, low-cost, high-bandwidth asynchronous (real-time) data
interfacing between computers, peripherals, and consumer electronic
devices such as camcorders, VCRs, printers,TVs, and digital cameras. See
page 2-29 for details.
ASUS A8R32-MVP DELUXE
1-3
USB 2.0 technology
The motherboard implements the Universal Serial Bus (USB) 2.0
specification, dramatically increasing the connection speed from the
12 Mbps bandwidth on USB 1.1 to a fast 480 Mbps on USB 2.0. USB 2.0 is
backward compatible with USB 1.1. See pages 2-21 and 2-27 for details.
1-4
Chapter 1: Product introduction
1.3.2 Innovative ASUS features
Fanless Design
The ASUS fanless design allows multi-directional heat flow from major
thermal sources in the motherboard to lower overall system temperature,
resulting in quieter operation and longer system life.
Stack Cool 2
The motherboard comes with the ASUS Stack Cool 2, an innovative fan-less
and zero-noise thermal solution that provides supplementary cooling to the
motherboard. Stack Cool 2 is a special layer underneath the motherboard
that improves heat dissipation.
SATA-On-the-Go
Leveraging the Serial ATA II feature is the SATA-On-the-Go. This external
port on the rear panel I/O provides smart setup, hot-plug and support for
up to 16 devices with port-multiplier functions. See pages 2-21 for details.
AI NET2
The AI NET2 is a BIOS-based diagnostic tool that detects and reports
Ethernet cable faults and shorts. With this utility, you can easily monitor
the condition of the Ethernet cable(s) connected to the LAN (RJ-45)
port(s). During the bootup process, AI NET2 immediately diagnoses the
LAN cable(s) and reports shorts and faults up to 100 meters at 1 meter
accuracy. See page 5-12 for details.
Precision Tweaker
This feature allows you to fine tune the CPU/memory/Northbridge voltage
and gradually increase the memory Front Side Bus (FSB) and PCI Express
frequency at 1MHz increment to achieve maximum system performance.
See pages 4-19 and 4-20 for details.
AI NOS™ (Non-Delay Overclocking System)
ASUS Non-delay Overclocking System™ (NOS) is a technology that
auto-detects the CPU loading and dynamically overclocks the CPU speed
only when needed. See page 4-19 for details.
ASUS A8R32-MVP DELUXE
1-5
PEG Link Mode for two graphics cards
This feature enhances your PCI Express graphics card performance, allowing
the motherboard to automatically adjust the PCI Express graphics link mode
to the correct frequency based on the system configuration. Four
additional settings are available for overclocking the PEG Link Mode. See
page 4-20 for details.
ASUS Q-Fan 2 technology
The ASUS Q-Fan 2 technology smartly adjusts the CPU and chassis fans
speed according to the system loading to ensure quiet, cool, and efficient
operation. See page 4-39 for details.
ASUS CrashFree BIOS 2
This feature allows you to restore the original BIOS data from the support CD
when the BIOS codes and data are corrupted. This protection eliminates the
need to buy a replacement ROM chip. See page 4-9 for details.
ASUS Multi-language BIOS
The multi-language BIOS allows you to select the language of your choice
from the available options. The localized BIOS menus allow easier and faster
configuration. See page 4-14 for details.
ASUS MyLogo2™
This new feature present in the motherboard allows you to personalize and
add style to your system with customizable boot logos. See page 4-42 for
details.
C.P.R. (CPU Parameter Recall)
The C.P.R. feature of the motherboard BIOS allows automatic re-setting to
the BIOS default settings in case the system hangs due to overclocking.
When the system hangs due to overclocking, C.P.R. eliminates the need to
open the system chassis and clear the RTC data. Simply shut down and
reboot the system, and the BIOS automatically restores the CPU default
setting for each parameter. See page 2-19 for details.
ASUS EZ Flash BIOS
With the ASUS EZ Flash, you can easily update the system BIOS even
before loading the operating system. No need to use a DOS-based utility or
boot from a floppy disk. See page 4-5 for details.
1-6
Chapter 1: Product introduction
This chapter lists the hardware setup
procedures that you have to perform
when installing system components.
It includes description of the jumpers
and connectors on the motherboard.
Hardware
2
information
Chapter summary
2
2.1
2.2
2.3
2.4
2.5
2.6
2.7
Before you proceed .............................................................. 2-1
Motherboard overview.......................................................... 2-2
Central Processing Unit (CPU) .............................................. 2-6
System memory .................................................................2-11
Expansion slots...................................................................2-15
Jumper ...............................................................................2-19
Connectors .........................................................................2-20
ASUS A8R32-MVP DELUXE
2.1 Before you proceed
Take note of the following precautions before you install motherboard
components or change any motherboard settings.
•
Unplug the power cord from the wall socket before touching any
component.
•
Use a grounded wrist strap or touch a safely grounded object or a
metal object, such as the power supply case, before handling
components to avoid damaging them due to static electricity
•
•
Hold components by the edges to avoid touching the ICs on them.
Whenever you uninstall any component, place it on a grounded
antistatic pad or in the bag that came with the component.
•
Before you install or remove any component, ensure
that the ATX power supply is switched off or the
power cord is detached from the power supply. Failure
to do so may cause severe damage to the motherboard, peripherals,
and/or components.
Onboard LED
The motherboard comes with a standby power LED that lights up to
indicate that the system is ON, in sleep mode, or in soft-off mode.
This is a reminder that you should shut down the system and unplug
the power cable before removing or plugging in any motherboard
component. The illustration below shows the location of the onboard
LED.
SB_PWR
®
A8R32-MVP DELUXE
ON
OFF
Standby
Power
Powered
Off
A8R32-MVP DELUXE Onboard LED
Make sure to connect the EZPlug when using two PCI Express graphics
cards and a 20-pin ATX power supply unit, or if the graphics cards do
not have auxiliary power plugs. See page 2-26 for the location of the
EZPlug connector.
ASUS A8R32-MVP DELUXE
2-1
2.2 Motherboard overview
Before you install the motherboard, study the configuration of your chassis
to ensure that the motherboard fits into it. Refer to the chassis
documentation before installing the motherboard.
Make sure to unplug the power cord before installing or removing the
motherboard. Failure to do so can cause you physical injury and damage
motherboard components.
2.2.1 Placement direction
When installing the motherboard, make sure that you place it into the
chassis in the correct orientation. The edge with external ports goes to the
rear part of the chassis as indicated in the image below.
2.2.2 Screw holes
Place nine (9) screws into the holes indicated by circles to secure the
motherboard to the chassis.
Do not overtighten the screws! Doing so can damage the motherboard.
Place this side towards
the rear of the chassis
®
A8R32-MVP DELUXE
2-2
Chapter 2: Hardware information
2.2.3 Motherboard layout
24.5cm (9.6in)
PS/2KBMS
T: Mouse
B: Keyboard
PWR_FAN
CPU_FAN
ATX12V
SPDIF_O
SPDIF_O2
AUDIO
LAN1_USB12
LAN2_USB34
ATI™
CrossFire™
Xpress 3200
SATA_RAID2
CHA_FAN1
USB78_WFG
Marvell
88E8053
AAFP
PCIEX16_1
CD
CHA_FAN2
SATA4
PCIEX1_1
®
ACL882
SATA3
SATA1
ULI
M1575
PCI1
SATA2
Marvell
88E8001
PCIEX16_2
A8R32-MVP DELUXE
8Mb
BIOS
PCI2
CR2032 3V
Lithium Cell
CMOS Power
TSB43AB22A
CLRTC
SB_PWR
COM1
PCI3
CHASSIS
PANEL
USB56
IE1394_1
IE1394_2
GAME
ASUS A8R32-MVP DELUXE
2-3
2.2.4 Layout Contents
Slots
Page
1. DDR DIMM slots
2. PCI slots
3. PCI Express x1 slot
4. PCI Express x16 slots
2-11
2-17
2-17
2-17
Jumper
Page
2-19
1. Clear RTC RAM (3-pin CLRTC)
Rear panel connectors
Page
1. PS/2 mouse port
2. Parallel port
3. Side Speaker Out port
4. Center/Subwoofer port
5. Line In port
6. Line Out port
7. LAN 1 (RJ-45)
8. LAN 2 (RJ-45)
9. USB 2.0 ports 3 and 4
10. USB 2.0 ports 1 and 2
11. Microphone port
12. Rear Speaker Out port
13. External SATA port
14. Optical S/PDIF Out port
15. Coaxial S/PDIF Out port
16. PS/2 keyboard port
2-20
2-20
2-20
2-20
2-20
2-20
2-21
2-21
2-21
2-21
2-21
2-21
2-21
2-21
2-21
2-21
2-4
Chapter 2: Hardware information
Internal connectors
P
a
g
e
1. Floppy disk drive connector (34-1 pin FLOPPY)
2. IDE connectors (40-1 pin PRI_IDE, 40-1 pin SEC_IDE)
2-22
2-22
3. Serial ATA connectors (7-pin SATA1 [red], SATA2 [red],
SATA3 [black], SATA4 [black])
2-23
2-25
2-26
4. Silicon Image Serial ATA RAID connector (7-pin SATA_RAID 2)
5. CPU, Chassis, and Power fan connectors
(3-pin CPU_FAN, 3-pin CHA_FAN1, 3-pin CHA_FAN2, 3-pin PWR_FAN )
6. USB connectors (10-1 USB56, USB78_WFG)
7. Power connectors (24-pin EATXPWR, 4-pin ATX12V)
8. GAME/MIDI port connector (16-1 pin GAME)
9. Serial port connector (10-1 pin COM1)
10. IEEE 1394a connectors (10-1 pin IE1394_1; 10-1 pin IE1394_2)
11. Chassis intrusion connector (4-1 pin CHASSIS)
12. Front panel audio connector (10-1 pin AAFP)
13. Audio connector (4-pin CD [black])
14. System panel connectors (20-1 pin PANEL)
- System Power LED (Green 3-pin PLED)
- Hard Disk activity (Red 2-pin IDE_LED)
- System warning speaker (Orange 4-pin SPEAKER)
- Power/Soft-off button(Yellow 2-pin PWRSW)
- Reset switch (Blue 2-pin RESET)
2-27
2-27
2-28
2-29
2-29
2-30
2-31
2-31
2-32
ASUS A8R32-MVP DELUXE
2-5
2.3 Central Processing Unit (CPU)
The motherboard comes with a surface mount 939-pin Zero Insertion Force
(ZIF) socket designed for the AMD Athlon™ 64FX/AMD Athlon™ 64 /
Athlon™ 64 X2/Opteron processor.
The 128-bit-wide data paths of these processors can run applications
faster than processors with only 32-bit or 64-bit wide data paths.
Take note of the marked corner (with gold
triangle) on the CPU. This mark should match
a specific corner on the socket to ensure
correct installation.
Gold
triangle
2.3.1 Installing the CPU
To install a CPU.
1. Locate the 939-pin ZIF socket on the motherboard.
®
A8R32-MVP DELUXE
A8R32-MVP DELUXE CPU Socket 939
2. Unlock the socket by pressing
the lever sideways, then lift it up
to a 90°-100° angle.
Socket lever
Make sure that the socket lever is lifted up to 90°-100° angle, otherwise
the CPU does not fit in completely.
2-6
Chapter 2: Hardware information
3. Position the CPU above the
socket such that the CPU corner
with the gold triangle matches
the socket corner with a small
triangle.
4. Carefully insert the CPU into the
socket until it fits in place.
Small triangle
Gold triangle
The CPU fits only in one correct orientation. DO NOT force the CPU into
the socket to prevent bending the pins and damaging the CPU!
5. When the CPU is in place, push
down the socket lever to secure
the CPU. The lever clicks on the
side tab to indicate that it is
locked.
6. Install a CPU heatsink and fan
following the instructions that
came with the heatsink package.
ASUS A8R32-MVP DELUXE
2-7
2.3.2 Installing the heatsink and fan
The AMD Athlon™ 64FX/Athlon™ 64/Athlon™ 64 X2 processor requires a
specially designed heatsink and fan assembly to ensure optimum thermal
condition and performance.
Make sure that you use only AMD-certified heatsink and fan assembly.
To install the CPU heatsink and fan:
1. Place the heatsink on top of the installed CPU, making sure that the
heatsink fits properly on the retention module base.
•
•
•
The retention module base is already installed on the motherboard
upon purchase.
You do not have to remove the retention module base when
installing the CPU or installing other motherboard components.
If you purchased a separate CPU heatsink and fan assembly, make
sure that a Thermal Interface Material is properly applied to the CPU
heatsink or CPU before you install the heatsink and fan assembly.
CPU fan
CPU heatsink
Retention module base
Retention bracket
Retention bracket lock
Your boxed CPU heatsink and fan assembly should come with installation
instructions for the CPU, heatsink, and the retention mechanism. If the
instructions in this section do not match the CPU documentation, follow
the latter.
2-8
Chapter 2: Hardware information
2. Attach one end of the retention
bracket to the retention module
base.
3. Align the other end of the
retention bracket (near the
retention bracket lock) to the
retention module base. A clicking
sound denotes that the retention
bracket is in place.
Make sure that the fan and
heatsink assembly perfectly fits
the retention mechanism module
base, otherwise you cannot snap
the retention bracket in place.
4. Push down the retention bracket
lock on the retention mechanism
to secure the heatsink and fan to
the module base.
ASUS A8R32-MVP DELUXE
2-9
5. When the fan and heatsink assembly is in place, connect the CPU fan
cable to the connector on the motherboard labeled CPU_FAN.
CPU_FAN
®
A8R32-MVP DELUXE
A8R32-MVP DELUXE CPU fan connector
Do not forget to connect the CPU fan connector! Hardware monitoring
errors can occur if you fail to plug this connector.
2-10
Chapter 2: Hardware information
2.4 System memory
2.4.1 Overview
The motherboard comes with four 184-pin Double Data Rate (DDR) Dual
Inline Memory Modules (DIMM) sockets.
The following figure illustrates the location of the sockets:
®
A8R32-MVP DELUXE
A8R32-MVP DELUXE 184-pin DDR DIMM sockets
Channel
Sockets
Channel A
Channel B
DIMM_A1 and DIMM_A2
DIMM_B1 and DIMM_B2
In dual-channel configurations, installing identical (the same type and
size) DDR DIMM pairs for each channel provides optimum performance.
ASUS A8R32-MVP DELUXE
2-11
2.4.2 Memory Configurations
You may install 256 MB, 512 MB, and 1 GB unbuffered ECC/non-ECC DDR
DIMMs into the DIMM sockets using the memory configurations in this
section.
•
If you installed four 1 GB memory modules, the system may detect
less than 3 GB of total memory because of address space allocation
for other critical functions. This limitation applies to Windows® XP
32-bit version operating system since it does not support Physical
Address Extension (PAE).
•
•
•
When using only one DDR DIMM module, install it into slot DIMM_B1
only.
For single-channel memory configuration, start installing the DDR
DIMMs from slot DIMM_B1 or DMM_B2.
For dual-channel memory configuration, install the DIMMs in slots
DIMM_B1 and DIMM_A1 (blue slots); install another pair of DIMMs in
slots DIMM_B2 and DIMM_A2 (black slots).
•
•
Always install DIMMs with the same CAS latency. For optimum
results, we recommend that you obtain memory modules from the
same vendor. Refer to the Qualified Vendors List on the next page
for details.
When you install four double-sided 400 MHz DDR DIMMs, the
frequency of each module downgrades to 333 MHz.
Recommended memory configurations
Sockets
Mode
DIMM_A1
DIMM_A2
DIMM_B1 DIMM_B2
Single-channel
Dual-channel*
(1)
(1)
(2)
–
–
–
Populated
Populated
Populated
–
–
Populated
Populated
Populated
Populated
* Use only identical DDR DIMM pairs.
* For dual-channel configuration (2), you may:
• install identical DIMMs in all four sockets
O R
• install identical DIMM pair in DIMM_A1 and DIMM_B1 (blue sockets)
2-12
Chapter 2: Hardware information
DDR (400 MHz) Qualified Vendors List
D I M M s u p p o r t
A B C
S i z e
Vendor
Chip No.
B r a n d Side/s* Part No.
256 MB KINGSTON
512 MB KINGSTON
512 MB KINGSTON
256 MB KINGSTON
256 MB KINGSTON
512 MB KINGSTON
512 MB SAMSUNG
512 MB SAMSUNG
256 MB Infineon
512 MB Infineon
256 MB CORSAIR
V58C2256804SAT5(ECC)
V58C2256804SAT5(ECC)
Heat-Sink Package
D3208DL3T-5A
A2S56D30BTP
HY5DU12822BT-D43
K4H560838E-TCCC(ECC) SAMSUNG DS
K4H560838F-TCCC
HYB25D256800CE-5C
HYB25D512800CE-5C
W942508BH-5
–
–
–
–
–
–
SS
DS
DS
SS
SS
SS
KVR400X72C3A/256
KVR400X72C3A/512
KHX3200A/512
• • •
• • •
• • •
• • •
• • •
• • •
• • •
• • •
• • •
• • •
• • •
• • •
• • •
• • •
• • •
• • •
• • •
• • •
• • •
KVR400X64C3A/256
KVR400X64C3A/256
KVR400X64C3A/512
M381L6423ETM-CCC
M368L6423FTN-CCC
HYS64D32300HU-5-C
HYS64D64300HU-5-C
CMX256A-3200C2PT
VS512MB400
SAMSUNG DS
Infineon
Infineon
SS
SS
SS
DS
DS
–
–
–
512MB
CORSAIR
VS32M8-5
512 MB Hynix
HY5DU56822DT-D43
K4H560838F-TCCC
K4H560838F-TCCC
HY5DU56822CT-D43
HY5DU56822CT-D43
ADD8608A8A-5B
KDL388P4LA-50
HYMD264646D8J-D43
TS64MLD64V4F3
512 M
Transcend
SAMSUNG DS
SAMSUNG DS
Hynix
512 MB A DATA
256 MB A DATA
512 MB A DATA
256 MB A DATA
512 MB KINGMAX
MDOSS6F3H41Y0N1E0Z
MDOHY6F3G31Y0N1E0Z
MDOHY6F3H41Y0N1E0Z
MDOAD5F3G31Y0N1E02
MPXC22D-38KT3R
SS
DS
SS
DS
Hynix
–
–
Legend:
A - supports one module inserted in DIMM_B1 slot in a Single-channel memory
configuration.
B - Supports one pair of modules inserted into either the blue slots or the black
slots as one pair of Dual-channel memory configuration.
C - Supports 4 modules inserted into both the blue and black slots as two pairs of
Dual-channel memory configuration
S S - Single-sided
D S - Double-sided
Visit the ASUS website (www.asus.com) for the latest Qualified Vendors
List.
ASUS A8R32-MVP DELUXE
2-13
2.4.3 Installing a DDR DIMM
Make sure to unplug the power supply before adding or removing DIMMs
or other system components. Failure to do so may cause severe damage
to both the motherboard and the components.
2
1. Unlock a DIMM socket by
DDR DIMM notch
pressing the retaining clips
outward.
1
2. Align a DIMM on the socket such
that the notch on the DIMM
matches the break on the
socket.
1
Unlocked retaining clip
A DDR DIMM is keyed with a notch so that it fits in only one direction.
DO NOT force a DIMM into a socket to avoid damaging the DIMM.
3. Firmly insert the DIMM into the
socket until the retaining clips
snap back in place and the DIMM
is properly seated.
Locked Retaining Clip
2.4.4 Removing a DDR DIMM
To remove a DIMM:
2
1. Simultaneously press the
retaining clips outward to unlock
the DIMM.
1
1
DDR DIMM notch
Support the DIMM lightly with your fingers when pressing the retaining
clips. The DIMM might get damaged when it flips out with extra force.
2. Remove the DIMM from the socket.
2-14
Chapter 2: Hardware information
2.5 Expansion slots
In the future, you may need to install expansion cards. The following
sub-sections describe the slots and the expansion cards that they support.
Make sure to unplug the power cord before adding or removing
expansion cards. Failure to do so may cause you physical injury and
damage motherboard components.
2.5.1 Installing an expansion card
To install an expansion card:
1. Before installing the expansion card, read the documentation that
came with it and make the necessary hardware settings for the card.
2. Remove the system unit cover (if your motherboard is already
installed in a chassis).
3. Remove the bracket opposite the slot that you intend to use. Keep
the screw for later use.
4. Align the card connector with the slot and press firmly until the card is
completely seated on the slot.
5. Secure the card to the chassis with the screw you removed earlier.
6. Replace the system cover.
2.5.2 Configuring an expansion card
After installing the expansion card, configure it by adjusting the software
settings.
1. Turn on the system and change the necessary BIOS settings, if any.
See Chapter 4 for information on BIOS setup.
2. Assign an IRQ to the card. Refer to the tables on the next page.
3. Install the software drivers for the expansion card.
ASUS A8R32-MVP DELUXE
2-15
2.5.3 Interrupt assignments
Standard interrupt assignments
I R Q
Priority
Standard Function
0
1
2
System Timer
1
Keyboard Controller
2
—
11
12
13
14
15
3
Re-direct to IRQ #9
Reserved
3
4
Communications Port (COM1)*
IRQ holder for PCI steering*
Floppy Disk Controller
5
6
7
Printer Port (LPT1)*
8
System CMOS/Real Time Clock
IRQ holder for PCI steering*
IRQ holder for PCI steering*
IRQ holder for PCI steering*
PS/2 Compatible Mouse Port*
Numeric Data Processor
Primary IDE/SATA Channel
Secondary IDE/SATA Channel
9
4
10
11
12
13
14
15
5
6
7
8
9
10
* These IRQs are usually available for ISA or PCI devices.
IRQ assignments for this motherboard
A
B
C
D
E
F
G
H
PCI slot 1
—
—
—
—
—
—
shared shared shared shared
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
PCI slot 2
—
—
—
—
—
shared shared shared shared
PCI slot 3
IEEE 1394
PCI Express LAN (88E8053)
PCI LAN (88E8001)
PCI-E x1
PCI-E x16_1
PCI-E x16_2
Onboard USB controller 1
Onboard USB controller 2
Onboard USB controller 3
Onboard USB 2.0 controller
HD audio
—
—
shared
—
shared shared shared shared
—
—
—
shared
—
—
—
—
—
—
shared
—
—
shared shared shared shared
shared shared shared shared
shared shared shared shared
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
shared
—
—
shared
—
—
—
shared
shared
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
shared
—
Serial ATA
Silicon Image SATA controller
—
—
shared
—
—
shared
—
—
—
—
When using PCI cards on shared slots, ensure that the drivers support
“Share IRQ” or that the cards do not need IRQ assignment; otherwise,
conflicts will arise between the two PCI groups, making the system
unstable and the card inoperable.
2-16
Chapter 2: Hardware information
2.5.4 PCI slots
The PCI slots support cards such as a
LAN card, SCSI card, USB card, and
other cards that comply with PCI
specifications. The figure shows a
LAN card installed on a PCI slot.
2.5.5 PCI Express x1 slot
This motherboard supports PCI
Express x1 network cards, SCSI cards
and other cards that comply with the
PCI Express specifications. The
following figure shows a network card
installed on the PCI Express x1 slot.
2.5.6 Two PCI Express x16 slots
This motherboard supports two ATI
CrossFire™ PCI Express x16 graphics
cards that comply with the PCI
Express specifications. The figure
shows two graphics cards installed on
the PCI Express x16 slots.
See Chapter 6 for details on the
CrossFire™ technology feature.
ASUS A8R32-MVP DELUXE
2-17
•
•
•
•
We recommend that you install a VGA card on the primary (blue) PCI
Express slot and install any other PCI Express device on the
secondary (black) PCI Express slot.
In CrossFire™ mode, install the ATI CrossFire™ Edition
(Master) graphics card on the primary (blue) PCI
Express slot; otherwise, the system will not boot.
If you do not configure the PCI Express device (s) according to the
table below, the system may have a failed or delayed power-on self
test (POST).
Refer to the table below for possible PCI Express Card
configurations.
PCI Express x16 slot configurations
PCIEX16_1 (blue) slot
PCIEX16_2 (black) slot
Card Type
Speed
Card Type
Speed
Single
graphics
card
PCIe x16 graphics card
x16
x16
PCIe x16 graphics card
PCIe devices (non-VGA)
x16
x16
Dual
graphics
cards in
CrossFire™
mode*
ATI CrossFire Edition
graphics card
x16
ATI CrossFire-ready
graphics card
Dual
graphics
cards (Dual
display)
Graphics card
x16
Graphics card
x16
*
In CrossFire™ mode, install two ATI graphics cards from the same
GPU family.
2-18
Chapter 2: Hardware information
2.6 Jumper
Clear RTC RAM (CLRTC)
This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS.
You can clear the CMOS memory of date, time, and system setup
parameters by erasing the CMOS RTC RAM data. The onboard button cell
battery powers the RAM data in CMOS, which include system setup
information such as system passwords.
To erase the RTC RAM:
1. Turn OFF the computer and unplug the power cord.
2. Remove the onboard battery.
3. Move the jumper cap from pins 1-2 (default) to pins 2-3. Keep the
cap on pins 2-3 for about 5~10 seconds, then move the cap back to
pins 1-2.
4. Reinstall the battery.
5. Plug the power cord and turn ON the computer.
6. Hold down the <Del> key during the boot process and enter BIOS
setup to re-enter data.
Except when clearing the RTC RAM, never remove the cap on CLRTC
jumper default position. Removing the cap will cause system boot failure!
CLRTC
®
1 2
2 3
A8R32-MVP DELUXE
Normal
Clear CMOS
(Default)
A8R32-MVP DELUXE Clear RTC RAM
You do not need to clear the RTC when the system hangs due to
overclocking. For system failure due to overclocking, use the C.P.R. (CPU
Parameter Recall) feature. Shut down and reboot the system so the BIOS
can automatically reset parameter settings to default values.
ASUS A8R32-MVP DELUXE
2-19
2.7 Connectors
2.7.1 Rear panel connectors
1
2
3 4 5 6
7
8
16
15
14
13
12 11
10
9
1 . PS/2 mouse port (green). This port is for a PS/2 mouse.
2 . Parallel port. This 25-pin port connects a parallel printer, a scanner,
or other devices.
3 . Side Speaker Out port (black). This port connects the side
speakers in an 8-channel audio configuration.
4 . Center/Subwoofer port (orange). This port connects the
center/subwoofer speakers.
5 . Line In port (light blue). This port connects a tape, CD, DVD
player, or other audio sources.
6 . Line Out port (lime). This port connects a headphone or a
speaker. In 4-channel, 6-channel, and 8-channel configuration, the
function of this port becomes Front Speaker Out.
Refer to the audio configuration table below for the function of the
audio ports in 2, 4, or 6, or 8-channel configuration.
Audio 2, 4, 6, or 8-channel configuration
Port
Headset
2-channel
4-channel
6-channel
8-channel
Light Blue
Lime
Pink
Line In
Line Out
Mic In
Line In
Front Speaker Out
Line In
Front Speaker Out
Mic In
Line In
Front Speaker Out
Mic In
Mic In
Gray
Black
Orange
•
•
•
Rear Speaker Out
Rear Speaker Out
•
Center/Subwoofer
Rear Speaker Out
Side Speaker Out
Center/Subwoofer
•
•
2-20
Chapter 2: Hardware information
7 . LAN 1 (RJ-45) port. Supported by Marvell® Gigabit LAN controller,
this port allows Gigabit connection to a Local Area Network (LAN)
through a network hub. Refer to the table below for the LAN port LED
indications.
8 . LAN 2 (RJ-45) port. Supported by the Marvell® Gigabit LAN
controller, this port allows Gigabit connection to a Local Area Network
(LAN) through a network hub.
32-bit OS LAN port LED indications
ACTIVITY/ SPEED
LINK LED
LED
Activity/Link
OFF
Speed LED
OFF
Description
Soft-off Mode
YELLOW*
YELLOW*
YELLOW*
OFF
During Power ON/OFF
100 Mbps connection
1 Gbps connection
ORANGE
GREEN
LAN port
* Blinking
9 . USB 2.0 ports 3 and 4. These two 4-pin Universal Serial Bus
(USB) ports are available for connecting USB 2.0 devices.
10. USB 2.0 ports 1 and 2. These two 4-pin Universal Serial Bus
(USB) ports are available for connecting USB 2.0 devices.
11. Microphone port (pink). This port connects a microphone.
12. Rear Speaker Out port (gray). This port connects the rear
speakers on a 4-channel, 6-channel, or 8-channel audio configuration.
13. External SATA port. This port connects to an external SATA box
or a Serial ATA port multiplier.
The external SATA port
supports external Serial ATA
1.5 and 3 Gb/s devices. Longer
cables support higher power
requirements to deliver signal
up to two meters away, and
enables improved hot-swap
function.
Do not insert a different
connector to this port.
14. Optical S/PDIF Out port. This port connects an external audio
output device via an optical S/PDIF cable.
15. Coaxial S/PDIF Out port. This port connects an external audio
output device via a coaxial S/PDIF cable.
16. PS/2 keyboard port (purple). This port is for a PS/2 keyboard.
ASUS A8R32-MVP DELUXE
2-21
2.7.2 Internal connectors
1 . Floppy disk drive connector (34-1 pin FLOPPY)
This connector is for the provided floppy disk drive (FDD) signal cable.
Insert one end of the cable to this connector, then connect the other
end to the signal connector at the back of the floppy disk drive.
Pin 5 on the connector is removed to prevent incorrect cable connection
when using an FDD cable with a covered Pin 5.
PIN 1
FLOPPY
NOTE: Orient the red markings on
the floppy ribbon cable to PIN 1.
®
A8R32-MVP DELUXE
A8R32-MVP DELUXE Floppy disk drive connector
2 . IDE connectors (40-1 pin PRI_IDE, 40-1 pin SEC_IDE)
These connectors are for Ultra DMA 133/100/66 signal cables. The
Ultra DMA 133/100/66 signal cable has three connectors: a blue
connector for the primary IDE connector on the motherboard, a black
connector for an Ultra DMA 133/100/66 IDE slave device (optical
drive/hard disk drive), and a gray connector for an Ultra DMA 133/
100/66 IDE master device (hard disk drive). If you install two hard disk
drives, you must configure the second drive as a slave device by setting
its jumper accordingly. Refer to the hard disk documentation for the
jumper settings.
•
Pin 20 on the IDE connector is removed to match the covered hole
on the Ultra DMA cable connector. This prevents incorrect insertion
when you connect the IDE cable.
•
Use the 80-conductor IDE cable for Ultra DMA 133/100/66 IDE
devices.
2-22
Chapter 2: Hardware information
NOTE: Orient the red markings
(usually zigzag) on the IDE
ribbon cable to PIN 1.
®
A8R32-MVP DELUXE
PIN 1
PIN 1
A8R32-MVP DELUXE IDE connectors
3 . Serial ATA connectors
(7-pin SATA1 [red], SATA2 [red], SATA3 [black],
SATA4 [black])
These connectors are for the Serial ATA signal cables for Serial ATA
hard disk drives.
If you installed Serial ATA hard disk drives, you can can create a
RAID 0, RAID 1, RAID 0+1, RAID 5, and JBOD configuration. Refer to
Chapter 5 for information on creating a RAID configuration.
Enable the Serial ATA Controller and Onboard SATA Boot ROM
items in the BIOS if you want to use the Serial ATA RAID feature. See
section “4.3.6 Storage Configuration” for details.
SATA3
SATA1
SATA4
SATA2
®
A8R32-MVP DELUXE
A8R32-MVP DELUXE SATA connectors
ASUS A8R32-MVP DELUXE
2-23
•
•
•
Plug your Serial ATA boot disk on the master port (SATA1/2 to
support S3 function).
Install the Windows® 2000 Service Pack 4 or the Windows® XP
Service Pack1 or later when using Serial ATA.
In RAID mode, the system cannot boot from a SATA CD-ROM which
is connected with the ULi M1575 controller.
Serial ATA hard disk drive connection
Connector
Color
Red
Black
Setting
Master
Slave
U s e
SATA1/SATA2
SATA3/SATA4
Boot disk
Data Disk
2-24
Chapter 2: Hardware information
4 . Silicon Image Serial ATA RAID connector
(7-pin SATA_RAID2)
This connector is for a Serial ATA signal cable. It supports a Serial ATA
hard disk drive that you can combine with an external Serial ATA
3 Gb/s device to configure a RAID 0 or RAID 1 set through the
onboard Silicon Image SATA RAID controller.
If you intend to create a RAID configuration using this connector, set the
Silicon 3132 Controller item in the BIOS to [RAID Mode]. See
section “4.4.4 Onboard Devices Configuration” for details.
SATA_RAID2
®
GND
RSATA_RXN1
RSATA_RXP1
GND
A8R32-MVP DELUXE
RSATA_TXN1
RSATA_TXP1
GND
A8R32-MVP DELUXE SATA RAID connector
•
Before creating a RAID set using Serial ATA hard disks, make sure
that you have connected the Serial ATA signal cable and installed
Serial ATA hard disk drives; otherwise, you cannot enter the Silicon
Image RAID utility and SATA BIOS setup during POST.
•
•
Use this connector and an external Serial ATA box connected to the
external SATA port, if you want to configure a RAID 0 or RAID 1 set.
The Serial ATA port multiplier and external Serial ATA box are
purchased separately.
DO NOT unplug the external Serial ATA box when a RAID 0 or RAID 1 is
configured.
ASUS A8R32-MVP DELUXE
2-25
5 . CPU, Chassis, and Power fan connectors
(3-pin CPU_FAN, 3-pin CHA_FAN1, 3-pin CHA_FAN2,
3-pin PWR_FAN)
The fan connectors support cooling fans of 350 mA ~ 2000 mA (24 W
max.) or a total of 1 A ~ 3.48 A (41.76 W max.) at +12 V. Connect
the fan cables to the fan connectors on the motherboard, making sure
that the black wire of each cable matches the ground pin of the
connector.
Do not forget to connect the fan cables to the fan connectors.
Insufficient air flow inside the system may damage the motherboard
components. These are not jumpers! DO NOT place jumper caps on the
fan connectors.
CPU_FAN
PWR_FAN
CPU_FAN
PWR_FAN
GND
+12V
Rotation
CHA_FAN1
CHA_FAN2
CHA_FAN1 CHA_FAN2
®
GND
GND
+12V
+12V
A8R32-MVP DELUXE
Rotation
Rotation
A8R32-MVP DELUXE Fan connectors
Only the CPU_FAN and CHA_FAN1 connectors support the
ASUS Q-Fan 2 feature.
For some chassis models with short 3-pin chassis fan cable, connect the
cable to the PWR_FAN connector.
2-26
Chapter 2: Hardware information
6 . USB connectors (10-1 pin USB56, USB78_WFG)
These connectors are for USB 2.0 ports. Connect the USB/GAME
module cable to any of these connectors, then install the module to a
slot opening at the back of the system chassis. These USB connectors
comply with USB 2.0 specification that supports up to 480 Mbps
connection speed.
®
USB78_WFG
USB56
1
1
A8R32-MVP DELUXE
A8R32-MVP DELUXE USB 2.0 connectors
Never connect a 1394 cable to the USB connectors. Doing so will
damage the motherboard!
7 . Power connectors (24-pin EATXPWR, 4-pin ATX12V)
These connectors are for an ATX power supply. The plugs from the
power supply are designed to fit these connectors in only one
orientation. Find the proper orientation and push down firmly until the
connectors completely fit.
EATXPWR
ATX12V
+3 Volts
-12 Volts
Ground
PSON#
Ground
Ground
Ground
-5 Volts
+5 Volts
+5 Volts
+5 Volts
Ground
+3 Volts
+3 Volts
Ground
+5 Volts
Ground
GND
+12V DC
GND
+12V DC
+5 Volts
Ground
®
Power OK
+5V Standby
+12 Volts
+12 Volts
+3 Volts
A8R32-MVP DELUXE
A8R32-MVP DELUXE ATX power connectors
ASUS A8R32-MVP DELUXE
2-27
•
For a fully-configured system, we recommend that you use a power
supply unit (PSU) that complies with ATX 12 V Specification 2.0 (or
later version) and provides a minimum power of 400 W.
•
•
Do not forget to connect the 4-pin ATX +12 V power plug;
otherwise, the system will not boot up.
The ATX 12 V Specification 2.0 compliant (400 W) PSU has been
tested to support the below configuration:
CPU:
AMD FX-57
Memory:
Graphics card:
Hard disk:
ATAPI:
512 MB DDR (x4)
PCI Express x16 ATI X850
SATA HD (x2)
CD-ROM (x1)
•
Use of a PSU with a higher power output is recommended when
configuring a system with more power-consuming devices. The
system may become unstable or may not boot up if the power is
inadequate.
•
If you want to use the ATI CrossFire™ Graphics solution, use a PSU
with 500 ~ 600 W power to ensure system stability.
8 . GAME/MIDI port connector (16-1 pin GAME)
This connector is for a GAME/MIDI port. Connect the USB/GAME
module cable to this connector, then install the module to a slot
opening at the back of the system chassis. The GAME/MIDI port
connects a joystick or game pad for playing games, and MIDI devices
for playing or editing audio files.
®
GAME
A8R32-MVP DELUXE
A8R32-MVP DELUXE Game connector
2-28
Chapter 2: Hardware information
9 . Serial port connector (10-1 pin COM1)
This connector is for a serial (COM) port. Connect the serial port
module cable to this connector, then install the module to a slot
opening at the back of the system chassis.
COM1
PIN 1
®
A8R32-MVP DELUXE
A8R32-MVP DELUXE COM port connector
10. IEEE 1394a connector (10-1 pin IE1394_1; 10-1 pin
IE1394_2)
These connectors are for IEEE 1394a ports. Connect the IEEE 1394a
module cable to this connector, then install the module to a slot
opening at the back of the system chassis.
®
IE1394_1
IE1394_2
A8R32-MVP DELUXE
1
1
A8R32-MVP DELUXE IEEE 1394 connectors
NEVER connect a USB cable to the IEEE 1394a connector. Doing so
will damage the motherboard!
ASUS A8R32-MVP DELUXE
2-29
11. Chassis intrusion connector (4-1 pin CHASSIS)
This connector is for a chassis-mounted intrusion detection sensor or
switch. Connect one end of the chassis intrusion sensor or switch
cable to this connector. The chassis intrusion sensor or switch sends a
high-level signal to this connector when a chassis component is
removed or replaced. The signal is then generated as a chassis
intrusion event.
By default, the pins labeled “Chassis Signal” and “Ground” are shorted
with a jumper cap. Remove the jumper caps only when you intend to
use the chassis intrusion detection feature.
®
A8R32-MVP DELUXE
CHASSIS
(Default)
A8R32-MVP DELUXE Chassis intrusion connector
2-30
Chapter 2: Hardware information
12. Front panel audio connector (10-1 pin AAFP)
This connector is for a chassis-mounted front panel audio I/O module
that supports either HD Audio or legacy AC ‘97 audio standard.
Connect one end of the front panel audio I/O module cable to this
connector.
AAFP
Azalia
compliant definition
Legacy AC’97
compliant definition
®
A8R32-MVP DELUXE
A8R32-MVP DELUXE Analog front panel connector
•
•
We recommend that you connect a high-definition front panel audio
module to this connector to avail of the motherboard’s
high-definition audio capability.
Make sure the HD Audio item in the BIOS is set to [Enabled] to avail
of the motherboard’s high-definition audio capability. See sectoin
“4.4.4 Onboard Devices Configuration” for details.
13. Audio connector (4-pin CD [black])
These connector allows you to receive stereo audio input from sound
sources such as a CD-ROM, TV-tuner, or MPEG card.
CD
(Black)
®
A8R32-MVP DELUXE
A8R32-MVP DELUXE Internal audio connector
ASUS A8R32-MVP DELUXE
2-31
14. System panel connector (20-1 pin PANEL)
This connector supports several chassis-mounted functions.
PLED
SPEAKER
PANEL
®
IDE_LED
RESET
A8R32-MVP DELUXE
PWRSW
*
Requires an ATX power supply.
A8R32-MVP DELUXE System panel connector
The sytem panel connector is color-coded for easy connection. Refer to
the connector description below for details.
•
•
System power LED (Green 3-pin PLED)
This 3-pin connector is for the system power LED. Connect the
chassis power LED cable to this connector. The system power LED
lights up when you turn on the system power, and blinks when the
system is in sleep mode.
Hard disk drive activity (Red 2-pin IDE_LED)
This 2-pin connector is for the HDD Activity LED. Connect the HDD
Activity LED cable to this connector. The IDE LED lights up or flashes
when data is read from or written to the HDD.
•
•
System warning speaker (Orange 4-pin SPEAKER)
This 4-pin connector is for the chassis-mounted system warning
speaker. The speaker allows you to hear system beeps and warnings.
Power/Soft-off button (Yellow 2-pin PWRSW)
This connector is for the system power button. Pressing the power
button turns the system ON or puts the system in SLEEP or SOFT-OFF
mode depending on the BIOS settings. Pressing the power switch for
more than four seconds while the system is ON turns the system OFF.
•
Reset button (Blue 2-pin RESET)
This 2-pin connector is for the chassis-mounted reset button for
system reboot without turning off the system power.
2-32
Chapter 2: Hardware information
This chapter describes the power up
sequence, the vocal POST messages,
and ways of shutting down the
system.
Powering up
3
Chapter summary
3
3.1
3.2
Starting up for the first time................................................ 3-1
Powering off the computer .................................................. 3-2
ASUS A8R32-MVP DELUXE
3.1 Starting up for the first time
1. After making all the connections, replace the system case cover.
2. Be sure that all switches are off.
3. Connect the power cord to the power connector at the back of the
system chassis.
4. Connect the power cord to a power outlet that is equipped with a
surge protector.
5. Turn on the devices in the following order:
a. Monitor
b.External SCSI devices (starting with the last device on the chain)
c. System power
6. After applying power, the system power LED on the system front
panel case lights up. For systems with ATX power supplies, the system
LED lights up when you press the ATX power button. If your monitor
complies with “green” standards or if it has a “power standby”
feature, the monitor LED may light up or switch between orange and
green after the system LED turns on.
The system then runs the power-on self tests or POST. While the
tests are running, the BIOS beeps (see BIOS beep codes table below)
or additional messages appear on the screen. If you do not see
anything within 30 seconds from the time you turned on the power,
the system may have failed a power-on test. Check the jumper
settings and connections or call your retailer for assistance.
AMI BIOS beep codes
Beep Description
One beep
Error
Keyboard controller error
Refresh Time error
No master drive detected
Two continuous beeps followed by
two short beeps
Floppy controller failure
Two continuous beeps followed by
Hardware component failure
four short beeps
7. At power on, hold down the <Delete> key to enter the BIOS Setup.
Follow the instructions in Chapter 4.
ASUS A8R32-MVP DELUXE
3-1
3.2 Powering off the computer
3.2.1 Using the OS shut down function
If you are using Windows® 2000:
1. Click the Start button then click Shut Down...
2. Make sure that the Shut Down option button is selected, then click
the OK button to shut down the computer.
3. The power supply should turn off after Windows® shuts down.
If you are using Windows® XP:
1. Click the Start button then select Turn Off Computer.
2. Click the Turn Off button to shut down the computer.
3. The power supply should turn off after Windows® shuts down.
3.2.2 Using the dual function power switch
While the system is ON, pressing the power switch for less than four
seconds puts the system to sleep mode or to soft-off mode, depending on
the BIOS setting. Pressing the power switch for more than four seconds
lets the system enter the soft-off mode regardless of the BIOS setting.
Refer to section “4.5 Power Menu” in Chapter 4 for details.
3-2
Chapter 3: Powering up
This chapter tells how to change
the system settings through the BIOS
Setup menus. Detailed descriptions
of the BIOS parameters are also
provided.
BIOS setup
4
Chapter summary
4
4.1
4.2
4.3
4.4
4.5
4.6
4.7
Managing and updating your BIOS ........................................ 4-1
BIOS setup program ...........................................................4-11
Main menu ..........................................................................4-14
Advanced menu..................................................................4-18
Power menu........................................................................4-35
Boot menu ..........................................................................4-40
Exit menu ...........................................................................4-45
ASUS A8R32-MVP DELUXE
4.1 Managing and updating your BIOS
The following utilities allow you to manage and update the motherboard
Basic Input/Output System (BIOS) setup.
1. ASUS Update (Updates the BIOS in Windows® environment.)
2. ASUS EZ Flash (Updates the BIOS using a floppy disk during POST.)
3. ASUS AFUDOS (Updates the BIOS in DOS mode using a bootable
floppy disk.)
4. ASUS CrashFree BIOS 2 (Updates the BIOS using a bootable
floppy disk or the motherboard support CD when the BIOS file fails or
gets corrupted.)
Refer to the corresponding sections for details on these utilities.
Save a copy of the original motherboard BIOS file to a bootable floppy
disk in case you need to restore the BIOS in the future. Copy the original
motherboard BIOS using the ASUS Update or AFUDOS utilities.
4.1.1 ASUS Update utility
The ASUS Update is a utility that allows you to manage, save, and update
the motherboard BIOS in Windows® environment. The ASUS Update utility
allows you to:
• Save the current BIOS file
• Download the latest BIOS file from the Internet
• Update the BIOS from an updated BIOS file
• Update the BIOS directly from the Internet, and
• View the BIOS version information.
This utility is available in the support CD that comes with the motherboard
package.
ASUS Update requires an Internet connection either through a network
or an Internet Service Provider (ISP).
Installing ASUS Update
To install ASUS Update:
1. Place the support CD in the optical drive. The Drivers menu appears.
2. Click the Utilities tab, then click Install ASUS Update
VX.XX.XX. See page 5-4 for the Utilities screen menu.
3. The ASUS Update utility is copied to your system.
ASUS A8R32-MVP DELUXE
4-1
Quit all Windows® applications before you update the BIOS using this
utility.
Updating the BIOS through the Internet
To update the BIOS through the Internet:
1. Launch the ASUS Update utility from the Windows® desktop by
clicking Start > Programs > ASUS > ASUSUpdate >
ASUSUpdate. The ASUS Update main window appears.
2. Select Update BIOS from
the Internet option from the
drop-down menu, then click
Next.
3. Select the ASUS FTP site
nearest you to avoid network
traffic, or click Auto Select.
Click Next.
4-2
Chapter 4: BIOS setup
4. From the FTP site, select the
BIOS version that you wish to
download. Click Next.
5. Follow the screen instructions to
complete the update process.
The ASUS Update utility is
capable of updating itself
through the Internet. Always
update the utility to avail all
its features.
Updating the BIOS through a BIOS file
To update the BIOS through a BIOS file:
1. Launch the ASUS Update utility from the Windows® desktop by
clicking Start > Programs > ASUS > ASUSUpdate >
ASUSUpdate. The ASUS Update main window appears.
2. Select Update BIOS from a
file option from the drop-down
menu, then click Next.
3. Locate the BIOS file from the
Open window, then click Save.
4. Follow the screen instructions to
complete the update process.
ASUS A8R32-MVP DELUXE
4-3
4.1.2 Creating a bootable floppy disk
1. Do either one of the following to create a bootable floppy disk.
DOS environment
a. Insert a 1.44MB floppy disk into the drive.
b. At the DOS prompt, type format A:/S then press <Enter>.
Windows® XP environment
a. Insert a 1.44 MB floppy disk to the floppy disk drive.
b. Click Start from the Windows® desktop, then select M y
Computer.
c. Select the 3 1/2 Floppy Drive icon.
d. Click File from the menu, then select Format. A Format 3 1/2
Floppy Disk window appears.
e. Select Create an MS-DOS startup disk from the format
options field, then click Start.
Windows® 2000 environment
To create a set of boot disks for Windows® 2000:
a. Insert a formatted, high density 1.44 MB floppy disk into the drive.
b. Insert the Windows® 2000 CD to the optical drive.
c. Click Start, then select Run.
d. From the Open field, type
D:\bootdisk\makeboot a:
assuming that D: is your optical drive.
e. Press <Enter>, then follow screen instructions to continue.
2. Copy the original or the latest motherboard BIOS file to the bootable
floppy disk.
4-4
Chapter 4: BIOS setup
4.1.3 ASUS EZ Flash utility
The ASUS EZ Flash feature allows you to update the BIOS without having to
go through the long process of booting from a floppy disk and using a
DOS-based utility. The EZ Flash utility is built-in the BIOS chip so it is
accessible by pressing <Alt> + <F2> during the Power-On Self Tests
(POST).
To update the BIOS using EZ Flash:
1. Visit the ASUS website (www.asus.com) to download the latest BIOS
file for the motherboard and rename the same to A8R32-MVP.ROM.
2. Save the BIOS file to a floppy disk, then restart the system.
3. Press <Alt> + <F2> during POST to display the following.
EZFlash starting BIOS update
Checking for floppy...
4. Insert the floppy disk that contains the BIOS file to the floppy disk
drive. When the correct BIOS file is found, EZ Flash performs the BIOS
update process and automatically reboots the system when done.
EZFlash starting BIOS update
Checking for floppy...
Floppy found!
Reading file “A8R32-MVP.ROM”. Completed.
Start erasing.......|
Start programming...|
Flashed successfully. Rebooting.
•
•
Do not shut down or reset the system while updating the BIOS to
prevent system boot failure!
A “Floppy not found!” error message appears if there is no floppy
disk in the drive. A “A8R32-MVP.ROM not found!” error message
appears if the correct BIOS file is not found in the floppy disk. Make
sure that you rename the BIOS file to A8R32-MVP.ROM.
ASUS A8R32-MVP DELUXE
4-5
4.1.4 AFUDOS utility
The AFUDOS utility allows you to update the BIOS file in DOS environment
using a bootable floppy disk with the updated BIOS file. This utility also
allows you to copy the current BIOS file that you can use as backup when
the BIOS fails or gets corrupted during the updating process.
Copying the current BIOS
To copy the current BIOS file using the AFUDOS utility:
•
•
Make sure that the floppy disk is not write-protected and has at
least 600 KB free space to save the file.
The succeeding BIOS screens are for reference only. The actual BIOS
screen displays may not be exactly the same as shown.
1. Copy the AFUDOS utility (afudos.exe) from the motherboard support
CD to the bootable floppy disk you created earlier.
2. Boot the system in DOS mode, then at the prompt type:
afudos /o[filename]
where the [filename] is any user-assigned filename not more than
eight alphanumeric characters for the main filename and three
alphanumeric characters for the extension name.
A:\>afudos /oOLDBIOS1.ROM
Main filename
Extension name
3. Press <Enter>. The utility copies the current BIOS file to the floppy
disk.
A:\>afudos /oOLDBIOS1.ROM
AMI Firmware Update Utility - Version 1.10
Copyright (C) 2002 American Megatrends, Inc. All rights reserved.
Reading flash ..... done
A:\>
The utility returns to the DOS prompt after copying the current BIOS
file.
4-6
Chapter 4: BIOS setup
Updating the BIOS file
To update the BIOS file using the AFUDOS utility:
1. Visit the ASUS website (www.asus.com) and download the latest BIOS
file for the motherboard. Save the BIOS file to a bootable floppy disk.
Write the BIOS filename on a piece of paper. You need to type the exact
BIOS filename at the DOS prompt.
2. Copy the AFUDOS utility (afudos.exe) from the motherboard support
CD to the bootable floppy disk you created earlier.
3. Boot the system in DOS mode, then at the prompt type:
afudos /i[filename]
where [filename] is the latest or the original BIOS file on the bootable
floppy disk.
A:\>afudos /iA8R32-MVP.ROM
4. The utility verifies the file and starts updating the BIOS.
A:\>afudos /iA8R32-MVP.ROM
AMI Firmware Update Utility - Version 1.19(ASUS V2.07(03.11.24BB))
Copyright (C) 2003 American Megatrends, Inc. All rights reserved.
WARNING!! Do not turn off power during flash BIOS
Reading file ..... done
Reading flash .... done
Advance Check........
Erasing flash .... done
Writing flash .... 0x0008CC00 (9%)
Do not shut down or reset the system while updating the BIOS to
prevent system boot failure!
ASUS A8R32-MVP DELUXE
4-7
5. The utility returns to the DOS prompt after the BIOS update process is
completed. Reboot the system from the hard disk drive.
A:\>afudos /iA8R32-MVP.ROM
AMI Firmware Update Utility - Version 1.19(ASUS V2.07(03.11.24BB))
Copyright (C) 2003 American Megatrends, Inc. All rights reserved.
WARNING!! Do not turn off power during flash BIOS
Reading file ..... done
Reading flash .... done
Search bootblock version
Advance Check.........
Erasing flash ..... done
Writing flash ..... done
Verifying flash ... done
Please restart your computer
A:\>
4-8
Chapter 4: BIOS setup
4.1.5 ASUS CrashFree BIOS 2 utility
The ASUS CrashFree BIOS 2 is an auto recovery tool that allows you to
restore the BIOS file when it fails or gets corrupted during the updating
process. You can update a corrupted BIOS file using the motherboard
support CD or the floppy disk that contains the updated BIOS file.
•
•
Prepare the motherboard support CD or the floppy disk containing
the updated motherboard BIOS before using this utility.
Make sure that you rename the original or updated BIOS file in the
floppy disk to A8R32-MVP.ROM.
Recovering the BIOS from a floppy disk
To recover the BIOS from a floppy disk:
1. Turn on the system.
2. Insert the floppy disk with the original or updated BIOS file to the
floppy disk drive.
3. The utility displays the following message and automatically checks
the floppy disk for the original or updated BIOS file.
Bad BIOS checksum. Starting BIOS recovery...
Checking for floppy...
When found, the utility reads the BIOS file and starts flashing the
corrupted BIOS file.
Bad BIOS checksum. Starting BIOS recovery...
Checking for floppy...
Floppy found!
Reading file “A8R32-MVP.ROM”. Completed.
Start flashing...
DO NOT shut down or reset the system while updating the BIOS! Doing
so can cause system boot failure!
4. Restart the system after the utility completes the updating process.
ASUS A8R32-MVP DELUXE
4-9
Recovering the BIOS from the support CD
To recover the BIOS from the support CD:
1. Remove any floppy disk from the floppy disk drive, then turn on the
system.
2. Insert the support CD to the optical drive.
3. The utility displays the following message and automatically checks
the floppy disk for the original or updated BIOS file.
Bad BIOS checksum. Starting BIOS recovery...
Checking for floppy...
When no floppy disk is found, the utility automatically checks the
optical drive for the original or updated BIOS file. The utility then
updates the corrupted BIOS file.
Bad BIOS checksum. Starting BIOS recovery...
Checking for floppy...
Floppy not found!
Checking for CD-ROM...
CD-ROM found!
Reading file “A8R32-MVP.ROM”. Completed.
Start flashing...
DO NOT shut down or reset the system while updating the BIOS! Doing
so can cause system boot failure!
4. Restart the system after the utility completes the updating process.
The recovered BIOS may not be the latest BIOS version for this
motherboard. Visit the ASUS website (www.asus.com) to download the
latest BIOS file.
4-10
Chapter 4: BIOS setup
4.2 BIOS setup program
This motherboard supports a programmable firmware chip that you can
update using the provided utility described in section “4.1 Managing and
updating your BIOS.”
Use the BIOS Setup program when you are installing a motherboard,
reconfiguring your system, or prompted to “Run Setup.” This section
explains how to configure your system using this utility.
Even if you are not prompted to use the Setup program, you can change
the configuration of your computer in the future. For example, you can
enable the security password feature or change the power management
settings. This requires you to reconfigure your system using the BIOS
Setup program so that the computer can recognize these changes and
record them in the CMOS RAM or the firmware hub.
The firmware hub on the motherboard stores the Setup utility. When you
start up the computer, the system provides you with the opportunity to
run this program. Press <Del> during the Power-On-Self-Test (POST) to
enter the Setup utility; otherwise, POST continues with its test routines.
If you wish to enter Setup after POST, restart the system by pressing
<Ctrl+Alt+Delete>, or by pressing the reset button on the system chassis.
You can also restart by turning the system off and then back on. Do this
last option only if the first two failed.
The Setup program is designed to make it as easy to use as possible. Being
a menu-driven program, it lets you scroll through the various sub-menus
and make your selections from the available options using the navigation
keys.
•
The default BIOS settings for this motherboard apply for most
conditions to ensure optimum performance. If the system becomes
unstable after changing any BIOS settings, load the default settings
to ensure system compatibility and stability. Select the Load
Default Settings item under the Exit Menu. See section “4.7 Exit
Menu.”
•
•
The BIOS setup screens shown in this section are for reference
purposes only, and may not exactly match what you see on your
screen.
Visit the ASUS website (www.asus.com) to download the latest BIOS
file for this motherboard.
ASUS A8R32-MVP DELUXE
4-11
4.2.1 BIOS menu screen
Menu items
Menu bar
Configuration fields
General help
BIOS SETUP UTILITY
Main
Advanced
Power
Boot
Exit
Use [ENTER], [TAB] or
[SHIFT-TAB] to select
a field.
System Time
System Date
Legacy Diskette A
Language
[10:55:25]
[Thu 12/15/2005]
[1.44M, 3.5 in]
[English]
Use [+] or [-] to
configure the System
Time.
Primary IDE Master
Primary IDE Slave
Secondary IDE Master
Secondary IDE Slave
Third IDE Master
Third IDE Slave
[ST320410A]
[ASUS CD-S520/A]
[Not Detected]
[Not Detected]
[Not Detected]
[Not Detected]
[Not Detected]
[Not Detected]
Select Screen
Select Item
Fourt IDE Master
Fourth IDE Slave
Storage Configuration
+-
Tab
F1
Change Field
Select Field
General Help
Save and Exit
Exit
F10
ESC
System Information
v02.58 (C)Copyright 1985-2005, American Megatrends, Inc.
Sub-menu items Navigation keys
4.2.2 Menu bar
The menu bar on top of the screen has the following main items:
Main For changing the basic system configuration
Advanced For changing the advanced system settings
Power
For changing the advanced power management (APM)
configuration
Boot
Exit
For changing the system boot configuration
For selecting the exit options and loading default
settings
To select an item on the menu bar, press the right or left arrow key on the
keyboard until the desired item is highlighted.
4.2.3 Navigation keys
At the bottom right corner of a menu screen are the navigation keys for
that particular menu. Use the navigation keys to select items in the menu
and change the settings.
Some of the navigation keys differ from one screen to another.
4-12
Chapter 4: BIOS setup
4.2.4 Menu items
BIOS SETUP UTILITY
Main
Advanced Power
Boot
Exit
Use [ENTER], [TAB],
or [SHIFT-TAB] to
select a field.
System Time
System Date
Legacy Diskette A
Language
[10:55:25]
The highlighted item on the menu
bar displays the specific items for
that menu. For example, selecting
Main shows the Main menu items.
[Wed 10/25/2005]
[1.44M, 3.5 in.]
[English]
Primary IDE Master [ST320410A]
Use [+] or [-] to
configure system
time.
Primary IDE Slave
[ASUS CD-S520/A]
Secondary IDE Master[Not Detected]
Secondary IDE Slave [Not Detected]
Third IDE Master
Third IDE Slave
Fourth IDE Master
Fourth IDE Slave
[Not Detected]
[Not Detected]
[Not Detected]
[Not Detected]
Select Screen
Select Item
Change Field
Select Field
General Help
Save and Exit
Exit
+-
Storage Configuration
System Information
Tab
F1
F10
ESC
The other items (Advanced,
Power, Boot, and Exit) on the
menu bar have their respective
menu items.
v02.5 (C)Copyright 1985-2005,American Megatrends, Inc.
Main menu items
4.2.5 Sub-menu items
A solid triangle before each item on any menu screen means that the iteam
has a sub-menu. To display the sub-menu, select the item and press
<Enter>.
4.2.6 Configuration fields
These fields show the values for the menu items. If an item is user-
configurable, you can change the value of the field opposite the item. You
cannot select an item that is not user-configurable.
A configurable field is enclosed in brackets, and is highlighted when
selected. To change the value of a field, select it then press <Enter> to
display a list of options. Refer to “4.2.7 Pop-up window.”
4.2.7 Pop-up window
Select a menu item then press <Enter> to display a pop-up window with
the configuration options for that item.
4.2.8 Scroll bar
Advanced PCI/PnP Settings
WARNING: Setting wrong values in
below sections may cause system to
A scroll bar appears on the right
malfunction.
Plug And Play O/S
PCI Latency Timer
Allocate IRQ to PCI VGA
Palette Snooping
[No]
side of a menu screen when there
are items that do not fit on the
screen. Press the
[64]
[Yes]
[Disabled]
[
PCI IDE BusMaster
Up/Down arrow keys or <Page
Up> /<Page Down> keys to
display the other items on the
screen.
Pop-up window
Scroll bar
4.2.9 General help
At the top right corner of the menu screen is a brief description of the
selected item.
ASUS A8R32-MVP DELUXE
4-13
4.3 Main menu
When you enter the BIOS Setup program, the Main menu screen appears,
giving you an overview of the basic system information.
Refer to section “4.2.1 BIOS menu screen” for information on the menu
screen items and how to navigate through them.
BIOS SETUP UTILITY
Main
Advanced
Power
Boot
Exit
Use [ENTER], [TAB] or
[SHIFT-TAB] to select
a field.
System Time
System Date
Legacy Diskette A
Language
[10:55:25]
[Mon 10/25/2005]
[1.44M, 3.5 in]
[English]
Use [+] or [-] to
configure the System
Time.
Primary IDE Master
Primary IDE Slave
Secondary IDE Master
Secondary IDE Slave
Third IDE Master
[ST320410A]
[ASUS CD-S520/A]
[Not Detected]
[Not Detected]
[Not Detected]
[Not Detected]
[Not Detected]
[Not Detected]
Third IDE Slave
Select Screen
Select Item
Fourth IDE Master
Fourth IDE Slave
Storage Configuration
+-
Tab
F1
Change Field
Select Field
General Help
Save and Exit
Exit
System Information
F10
ESC
v02.58 (C)Copyright 1985-2005, American Megatrends, Inc.
4.3.1 System Time [xx:xx:xx]
Allows you to set the system time.
4.3.2 System Date [Day xx/xx/xxxx]
Allows you to set the system date.
4.3.3 Legacy Diskette A [1.44M, 3.5 in.]
Sets the type of floppy drive installed. Configuration options: [Disabled]
[360K, 5.25 in.] [1.2M , 5.25 in.] [720K , 3.5 in.] [1.44M, 3.5 in.]
[2.88M, 3.5 in.]
4.3.4 Language [English]
Allows you to choose the BIOS language version from the options.
Configuration options: [Chinese (BIG5)] [Chinese (GB)] [Japanese]
[Français] [German] [English]
4-14
Chapter 4: BIOS setup
4.3.5 Primary, Secondary, Third, and Fourth
IDE Master/Slave
The BIOS automatically detects the connected IDE devices. There is a
separate sub-menu for each IDE device. Select a device item, then press
<Enter> to display the IDE device information.
BIOS SETUP UTILITY
Main
Primary IDE Master
Select the type of
device connected to
the system.
Device
: Hard Disk
Vendor
: ST320413A
: 20.0GB
Size
LBA Mode
Block Mode
PIO Mode
Async DMA
Ultra DMA
: Supported
: 16 Sectors
: 4
: MultiWord DMA-2
: Ultra DMA-6
SMART Monitoring: Supported
Type
[Auto]
[Auto]
LBA/Large Mode
Select Screen
Block(Multi-sector Transfer) M [Auto]
Select Item
PIO Mode
DMA Mode
[Auto]
+- Change Option
[Auto]
F1
General Help
Save and Exit
Exit
SMART Monitoring
32Bit Data Transfer
[Auto]
F10
ESC
[Disabled]
v02.58 (C)Copyright 1985-2005, American Megatrends, Inc.
The BIOS automatically detects the values opposite the dimmed items
(Device, Vendor, Size, LBA Mode, Block Mode, PIO Mode, Async DMA, Ultra
DMA, and SMART monitoring). These values are not user-configurable.
These items show N/A if no IDE device is installed in the system.
Type [Auto]
Selects the type of IDE drive. Setting to [Auto] allows automatic selection
of the appropriate IDE device type. Select [CDROM] if you are specifically
configuring a CD-ROM drive. Select [ARMD] (ATAPI Removable Media
Device) if your device is either a ZIP, LS-120, or MO drive.
Configuration options: [Not Installed] [Auto] [CDROM] [ARMD]
LBA/Large Mode [Auto]
Enables or disables the LBA mode. Setting to [Auto] enables the LBA mode
if the device supports this mode, and if the device was not previously
formatted with LBA mode disabled. Configuration options: [Disabled]
[Auto]
Block (Multi-sector Transfer) M [Auto]
Enables or disables data multi-sectors transfers. When set to [Auto], the
data transfer from and to the device occurs multiple sectors at a time if
the device supports multi-sector transfer feature. When set to [Disabled],
the data transfer from and to the device occurs one sector at a time.
Configuration options: [Disabled] [Auto]
ASUS A8R32-MVP DELUXE
4-15
PIO Mode [Auto]
Selects the PIO mode.
Configuration options: [Auto] [0] [1] [2] [3] [4]
DMA Mode [Auto]
Selects the DMA mode. Configuration options: [Auto] [SWDMA0]
[SWDMA1] [SWDMA2] [MWDMA0] [MWDMA1] [MWDMA2] [UDMA0]
[UDMA1] [UDMA2] [UDMA3] [UDMA4] [UDMA5] [UDMA6]
SMART Monitoring [Auto]
Sets the Smart Monitoring, Analysis, and Reporting Technology.
Configuration options: [Auto] [Disabled] [Enabled]
32Bit Data Transfer [Disabled]
Enables or disables 32-bit data transfer.
Configuration options: [Disabled] [Enabled]
4.3.6 Storage Configuration
BIOS SETUP UTILITY
Main
Storage Configuration
Options
Disabled
Serial ATA Controller
RAID Mode Selection
SATA Mode Selection
[Enabled]
Enabled
[SATA mode]
[Emulated PATA Mode]
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
+-
F1
F10
ESC
v02.58 (C)Copyright 1985-2004, American Megatrends, Inc.
Serial ATA Controller [Enabled]
Allows you to enable or disable the Serial ATA controller.
Configuration options: [Disabled] [Enabled]
4-16
Chapter 4: BIOS setup
The succeeding items appear only if the Serial ATA Controller item
is set to [Enabled].
RAID Mode Selection [SATA mode]
Allows you to select the RAID mode.
Configuration options: [SATA mode] [RAID mode]
SATA Mode Selection [Emulated PATA Mode]
Allows you to select the Serial ATA mode.
Configuration options: [Emulated PATA Mode] [AHCI Mode]
4.3.7 System Information
This menu gives you an overview of the general system specifications. The
BIOS automatically detects the items in this menu.
BIOS SETUP UTILITY
Main
AMIBIOS
Version
: 0111
Build Date : 12/28/05
Processor
Type
: AMD Athlon(tm) 64 Processor 3200+
: 2000 MHz
: 1
Speed
Count
System Memory
Size
: 512 MB
Select Screen
Select Item
General Help
Save and Exit
Exit
F1
F10
ESC
v02.58 (C)Copyright 1985-2004, American Megatrends, Inc.
AMI BIOS
Displays the auto-detected BIOS information.
Processor
Displays the auto-detected CPU specification.
System Memory
Displays the auto-detected system memory.
ASUS A8R32-MVP DELUXE
4-17
4.4 Advanced menu
The Advanced menu items allow you to change the settings for the CPU
and other system devices.
Take caution when changing the settings of the Advanced menu items.
Incorrect field values can cause the system to malfunction.
BIOS SETUP UTILITY
Main
Advanced
Power
Boot
Exit
Jumperfree Configuration
CPU Configuration
Chipset
Onboard Devices Configuration
PCIPnP
LAN Cable Status
USB Configuration
Select Screen
Select Item
Change option
General Help
Save and Exit
Exit
+-
F1
F10
ESC
v02.58 (C)Copyright 1985-2005, American Megatrends, Inc.
4.4.1 JumperFree Configuration
BIOS SETUP UTILITY
Advanced
Configure System Frequency/Voltage
AI Overclocking
[Auto]
FID/VID Change
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
DDR Voltage
VCORE Over-voltage
Northbridge Over-voltage
Southbridge Over-voltage
PEG Link Mode
PEG Buffer Length
[Disabled]
[Auto]
Select Screen
Select Item
Change option
General Help
Save and Exit
Exit
BankA DDR Clock Skew
BankB DDR Clock Skew
[Auto]
[Auto]
+-
F1
F10
ESC
v02.58 (C)Copyright 1985-2005, American Megatrends, Inc.
4-18
Chapter 4: BIOS setup
AI Overclocking [Auto]
Allows you to select the overclocking options to achieve the desired CPU
internal frequency. Select either one of the preset overclocking
configiuration options.
Setting
Description
Manual
Auto
Standard
Overclock Profile
allows you to individually set overclocking parameters.
loads the optimal settings for the system.
loads the standard settings for the system.
loads overclocking profiles with optimal
parameters for stability when overclocking.
AI N.O.S.
the ASUS AI Non-delay Overclocking System feature
intelligently determines the system load and
automatically boost the performance for the most
demanding tasks.
FID/VID Change [Auto]
When set to [Auto], FID/VID will be set at the rated frequency/voltage.
When set to [Manual], FID/VID will be set based on the user selection.
The following items appear only when the FID/VID Change item is
set to [Manual].
Processor Frequency Multiplier [x4]
Allows you to set the processor frequency multiplier.
Configuration options: [x4] [x4.5] [x5]... [x25.5]
Processor Voltage [1.450 V]
Allows you to set the processor voltage.
Configuration options: [1.450 V] [1.425 V] [1.400 V]... [0.800 V]
DDR Voltage [Auto]
Allows you to set the DDR memory voltage.
Configuration options: [Auto] [2.60 V] [2.65 V]...[3.20 V]
Setting a very high voltage may damage the component permanently.
Setting a very low voltage may cause the system to become unstable.
VCORE Over-voltage [Auto]
Allows you to enable or disable VCORE over-voltage.
Configuration options: [Auto] [Disabled] [Enable] [+100mV] [+200mV]
ASUS A8R32-MVP DELUXE
4-19
Northbridge Over-voltage [Auto]
Configuration options: [Auto] [Disabled] [Enabled]
Southbridge Over-voltage [Auto]
Configuration options: [Auto] [Disabled] [Enabled]
PEG Link Mode [Disabled]
Sets the PCI Express graphics (PEG) link mode. Setting this item to [Auto]
allows the motherboard to automatically adjust the PCI Express graphics
link mode to the correct frequency based on the system configuration.
Three additional settings are available for overclocking the PEG Link Mode.
Configuration options: [Auto] [Disabled] [Normal] [Fast] [Faster]
PEG Buffer Length [Auto]
Allows you to set the PEG buffer length.
Configuration options: [Auto] [Short] [Long] [Longer] [Longest]
BankA DDR Clock Skew [Auto]
Configuration options: [Auto] [Normal] [Advance 150ps] [Advance 300ps]
...[Advance 900] [Delay 150ps] [Delay 300ps]...[Delay 900]
BankB DDR Clock Skew [Auto]
Configuration options: [Auto] [Normal] [Advance 150ps] [Advance 300ps]
...[Advance 900] [Delay 150ps] [Delay 300ps]...[Delay 900]
The following items appear only when you set the AI Overclocking
item to [Manual].
CPU Frequency [XXX]
Allows you to adjust the CPU frequency. The value of this item is
auto-detected by the BIOS. Use the <+> and <-> keys to adjust the CPU
FSB frequency. You can also type the desired CPU frequency using the
numeric keypad. The values range from 200 to 400.
PCIE Frequency [XXX]
Allows you to adjust the PCIE frequency. The value of this item is
auto-detected by the BIOS. Use the <+> and <-> keys to adjust the PCIE
FSB frequency. You can also type the desired PCIE frequency using the
numeric keypad. The values range from 100 to 150.
The following item appears only when you set the AI Overclocking
item to [Ovrerclock Profile].
4-20
Chapter 4: BIOS setup
Overclock Options [Overclock 5%]
Allows you to overclock the CPU speed through the available preset values.
Configuration options: [Overclock 3%] [Overclock 5%] [Overclock 10%]
[Overclock 15%] [Overclock 20%] [Overclock 30%]
The following item appears only when you set the AI Overclocking
item to [AI N.O.S.].
Turbo N.O.S. [Overclock 3%]
Configuration options: [Overclock 3%] [Overclock 5%] [Overclock 7%]
[Overclock 10%] [Overclock 15%] [Overclock 20%]
ASUS A8R32-MVP DELUXE
4-21
4.4.2 CPU Configuration
The items in this menu show the CPU-related information that the BIOS
automatically detects.
BIOS SETUP UTILITY
Advanced
CPU Configuration
This option should
remain disabled for
the normal operation.
The driver developer
may enable it for
testing purpose.
Module Version: 14.08
Physical Count: 1
Logical Count: 1
AMD Athlon(tm) 64 Processor 3200+
Revision: D0
Cache L1: 128KB
Cache L2: 512KB
Speed: 2000 MHz
Current FSB Multiplier: 10x
Maximum FSB Multiplier: 10x
Able to Change Freq: Yes
uCode Patch Level: 0x4D
Select Screen
Select Item
GART Error Reporting
MTRR Mapping
[Disabled]
+-
F1
Change Option
General Help
Save and Exit
Exit
[Continuous]
[Disabled]
[Auto]
Cool `n’ Quiet
HT Link Speed
F10
ESC
Memory Configuration
v02.58 (C)Copyright 1985-2005, American Megatrends, Inc.
GART Error Reporting [Disabled]
Allows you to enable or disable GART error checking for testing purposes.
Configuration options: [Disabled] [Enabled]
MTRR Mapping [Continuous]
Determines the method used for programming processor MTRRs when using
more than 4 GB of system memory. Setting to [Discrete] leaves the PCI
hole below the 4 GB boundary undescribed. [Continuous] explicitly
describes the PCI hole as non-cacheable. Configuration options:
[Continuous] [Discrete]
Cool ‘n’ Quiet [Disabled]
Enables or disables the Cool ‘n’ Quiet™ technology feature.
Configuration options: [Enabled] [Disabled]
HT Link Speed [Auto]
Allows you to set the speed at which the HyperTransport link will run if the
speed is lower than or equal to the system clock and if the board is
capable. Configuration options: [Auto] [200 MHz] [400 MHz] [600 MHz]
[800 MHz] [1 GHz]
4-22
Chapter 4: BIOS setup
Memory Configuration
BIOS SETUP UTILITY
Advanced
Memory Configuration
Memory Timing Configuration
ECC Configuration
Memory CLK
CAS Latency (Tcl)
: 166 MHz
: 2.5
RAS/CAS Delay (Trcd)
Min Active RAS (Tras)
Row Precharge Time (Trp)
RAS/RAS Delay (Trrd)
Row Cycle (Trc)
: 3 CLK
: 7 CLK
: 3 CLK
: 2 CLK
: 10 CLK
: 12 CLK
: 4 CLK
: 6.0 ns
: 7 ns
Row Refresh Cycle (Trfc)
Read Write Delay (Trwt)
Read Preamble
Select Screen
Select Item
+- Change Option
Asynchronous Latency
F1
General Help
F10 Save and Exit
ESC Exit
v02.58 (C)Copyright 1985-2005, American Megatrends, Inc.
Memory Timing Configuration
BIOS SETUP UTILITY
Advanced
Memory Configuration
MEMCLK can be set by
the code using AUTO,
or if you use LIMIT,
you can set one of
the standard values.
Memclock Mode
[Auto]
MCT Timing Mode
MCT Extra Timing Mode
User Config Mode
Bank Interleaving
Burst Length
[Auto]
[Auto]
[Auto]
[Auto]
[4 Beats]
[Disabled]
SoftWare Memory Hole
Select Screen
Select Item
+- Change Option
F1
General Help
F10 Save and Exit
ESC Exit
v02.58 (C)Copyright 1985-2005, American Megatrends, Inc.
Memclock Mode [Auto]
[Auto] allows the BIOS to set the memclock mode automatically.
[Limit] allows you to select from any of the standard values.
Configuration options: [Auto] [Limit]
The following item appears when the Memclock Mode item is set to
[Limit].
Memclock Value [200 MHz]
Allows you to set the memclock value.
Configuration options: [100 MHz] [133 MHz] [166 MHz] [183 MHz] [200 MHz] [216
MHz] [233 MHz] [250 MHz]
ASUS A8R32-MVP DELUXE
4-23
MCT Timing Mode [Auto]
[Auto] allows the BIOS to set the MCT timing mode automatically.
[Manual] allows you to set the values by yourself.
Configuration options: [Auto] [Manual]
The following items appear when the MCT Timing Mode item is set
to [Manual].
CAS Latency (CL) [Auto]
Configuration options: [Auto] [2.0] [3.0] [2.5]
TRAS [Auto]
Configuration options: [Auto] [5 CLK] [6 CLK]... [15 CLK]
TRP [Auto]
Configuration options: [Auto] [2 CLK] [3 CLK]... [6 CLK]
TRCD [Auto]
Configuration options: [Auto] [2 CLK] [3 CLK]... [6 CLK]
TRRD [Auto]
Configuration options: [Auto] [2T] [3T] [4T]
TRC [Auto]
Configuration options: [Auto] [7T] [8T] [9T]... [22T]
TRFC [Auto]
Configuration options: [Auto] [9T] [10T] [11T]... [24T]
TRWT [Auto]
Configuration options: [Auto] [1 CLK] [2 CLK]... [6 CLK]
MCT Extra Timing Mode [Auto]
Allows you to manually configure the MCT Timing Mode parameters. .
Configuration options: [Auto] [Manual]
The following items appear when the MCT Extra Timing Mode item
is set to [Manual].
TREF [7.8us]
Configuration options: [15.6us] [7.8us] [3.9us]
DDR Input Strobe Skew [Disabled]
Configuration options: [Disabled] [Slower] [Faster]
DDR Data Driving Strength
Configuration options: [Disabled] [15% Reduced] [30% Reduced]
[45% Reduced]
Burst20pt [Disabled]
Configuration options: [Disabled] [Enabled]
4-24
Chapter 4: BIOS setup
User Config Mode [Auto]
Configuration options: [Auto] [Manual]
The following items appear when the User Config Mode item is set
to [Manual].
Read Preamble [5.5ns]
Configuration options: [2.0ns] [2.5ns] [3.0ns]... [9.5ns]
Asyc Latency [7.0ns]
Configuration options: [4.0ns] [5.0ns] [6.0ns]... [11.0ns]
CMD-ADDR Timing Mode [1T]
Configuration options: [1T] [2T]
Bank Interleaving [Auto]
Sets whether to allow memory accesses to be spread out over BANKS
on the same node or across nodes, decreasing access contention.
Configuration options: [Disabled] [Auto]
Burst length [4 Beats]
Sets the burst length.
Configuration options: [8 Beats] [4 Beats] [2 Beats]
Software Memory Hole [Disabled]
Enables or disables the software memory remapping around the
memory hole. Only REV E0 processors and above support this feature.
Configuration options: [Disabled] [Enabled]
ASUS A8R32-MVP DELUXE
4-25
ECC Configuration
BIOS SETUP UTILITY
Advanced
ECC Configuration
DRAM ECC allows
hardware to report and
correct memory errors
automatically,
maintaining system
integrity.
DRAM ECC Enable
[Enabled]
[Disabled]
[Disabled]
[Disabled]
[Disabled]
[Disabled]
[Disabled]
MCA DRAM ECC Logging
ECC Chip Kill
DRAM SCRUB REDIRECT
DRAM BG Scrub
L2 Cache BG Scrub
Data Cache BG Scrub
Select Screen
Select Item
+- Change Option
F1
General Help
F10 Save and Exit
ESC Exit
v02.58 (C)Copyright 1985-2005, American Megatrends, Inc.
DRAM ECC Enable [Enabled]
Allows you to enable or disable DRAM ECC, which allows the hardware
to report and correct memory errors automatically to maintain system
integrity. Configuration options: [Disabled] [Enabled]
MCA DRAM ECC Logging [Disabled]
Allows you to enable or disable MCA DRAM ECC logging/reporting.
Configuration options: [Disabled] [Enabled]
ECC Chip Kill [Disabled]
Allows you to enable or disable ECC chip kill.
Configuration options: [Disabled] [Enabled]
DRAM SCRUB REDIRECT [Disabled]
Allows you to enable or disable DRAM scrub redirect, which allows the system to
correct DRAM ECC errors immediately when they occur, even if background scrubbing is
on. Configuration options: [Disabled] [Enabled]
DRAM BG Scrub [Disabled]
Allows DRAM scrubbing to correct memory errors so later reads are correct. Doing this
while memory is not being used improves performance. Configuration options:
[Disabled] [40ns] [80ns] [160ns] [320ns] [640ns] [1.28us] [2.56us] [5.12us]
[10.2us] [20.5 us] [41.0us] [81.9us] [163.8us] [327.7us] [655.4us] [1.31ms]
[2.62ms] [5.24ms] [10.49ms] [20.97ms] [42.00ms] [84.00ms]
L2 Cache BG Scrub [Disabled]
Allows the L2 Data Cache RAM to be corrected while idle.
Configuration options: [Disabled] [40ns] [80ns] [160ns] [320ns]
[640ns] [1.28us] [2.56us] [5.12us] [10.2us] [20.5 us] [41.0us]
[81.9us] [163.8us] [327.7us] [655.4us] [1.31ms] [2.62ms]
[5.24ms] [10.49ms] [20.97ms] [42.00ms] [84.00ms]
4-26
Chapter 4: BIOS setup
Data Cache BG Scrub [Disabled]
Allows the L1 Data Cache RAM to be corrected while idle.
Configuration options: [Disabled] [40ns] [80ns] [160ns] [320ns]
[640ns] [1.28us] [2.56us] [5.12us] [10.2us] [20.5 us] [41.0us]
[81.9us] [163.8us] [327.7us] [655.4us] [1.31ms] [2.62ms]
[5.24ms] [10.49ms] [20.97ms] [42.00ms] [84.00ms]
4.4.3 Chipset Configuration
The Chipset menu allows you to change the advanced chipset settings.
Select an item then press <Enter> to display the sub-menu.
BIOS SETUP UTILITY
Advanced
Radeon Xpress Configuration
ATI Northbridge
ATI Northbridge Rev.
:RD580
:A11
Hyper Transport Configuration
PCI Express Configuration
Select Screen
Select Item
Enter Go to Sub Screen
F1
General Help
F10 Save and Exit
ESC Exit
v02.58 (C)Copyright 1985-2005, American Megatrends, Inc.
BIOS SETUP UTILITY
Advanced
Hyper Transport Configuration
HT Link Speed
CPU:RD580-NB HT Link Width
[Auto]
[Auto]
RD580 HT Link Three State
RD580 HT Drive Strength
HT Receiver Comp. Ctrl
[Disabled]
[Auto]
[Auto]
RD580 HT PLL Control
[Auto]
Select Screen
Select Item
Enter Go to Sub Screen
F1
General Help
F10 Save and Exit
ESC Exit
v02.58 (C)Copyright 1985-2005, American Megatrends, Inc.
ASUS A8R32-MVP DELUXE
4-27
Hyper Transport Configuration
Allows you to configure the HT links.
HT Link Speed [Auto]
The HyperTransport link will run at this speed if it is slower than or
equal to the system clock and the board is capable.
Configuration options: [Auto] [200 MHz] [400 MHz] [600 MHz]
[800 MHz] [1 GHz]
CPU:RD580-NB HT Link Width [Auto]
The HyperTransport link will run at this width.
Configuration options: [Auto] [8 Bit] [16 Bit]
RD580 HT Link Three State [Disabled]
Configuration options: [Disabled] [Enabled]
RD580 HT Drive Strength [Auto]
Configuration options: [Auto] [Manual]
The following items appear when the RD580 HT Drive Strength
item is set to [Manual].
HT Drive Strength Value [Level 0]
Configuration options: [Level 0] [Level 1] [Level 2]... [Level 31]
HT Receiver Comp. Ctrl [Auto]
Configuration options: [Auto] [Manual]
HT Receiver Comp. Value [Level 0]
Configuration options: [Level 0] [Level 1] [Level 2]... [Level 31]
This item appears when the HT Receiver Comp. Ctrl item is set to
[Manual].
RD580 HT PLL Control [Auto]
Configuration options: [Auto] [Low Speed] [High Speed]
4-28
Chapter 4: BIOS setup
Advanced
PCI Express Configuration
Options
x1
PCIE GFX1 Link Width
PCIE GFX2 Link Width
[x16]
[x16]
x2
x4
P2P Writes Between GFX Ports [Disabled]
x8
10% Extra Current for GPP
10% Extra Current for SB
10% Extra Current for GFX1
10% Extra Current for GFX2
[Enabled]
[Enabled]
[Enabled]
[Enabled]
x16
Select Screen
Select Item
Change Option
General Help
+-
F1
F10 Save and Exit
ESC Exit
v02.58 (C)Copyright 1985-2005, American Megatrends, Inc.
PCI Express Configuration
PCIE GFX1 Link Width [x16]
The PCIE GFX1 link will run at this width.
Configuration options: [x1] [x2] [x4] [x8] [x16]
PCIE GFX2 Link Width [x16]
The PCIE GFX2 link will run at this width.
Configuration options: [x1] [x2] [x4] [x8] [x16]
P2P Writes Between GFX Ports [Disabled]
Configuration options: [Disabled] [Enabled]
10% Extra Current for GPP [Enabled]
Configuration options: [Disabled] [Enabled]
10% Extra Current for SB [Enabled]
Configuration options: [Disabled] [Enabled]
10% Extra Current for GFX1 [Enabled]
Configuration options: [Disabled] [Enabled]
10% Extra Current for GFX2 [Enabled]
Configuration options: [Disabled] [Enabled]
ASUS A8R32-MVP DELUXE
4-29
4.4.4 Onboard Devices Configuration
BIOS SETUP UTILITY
Advanced
Onboard Devices
HD Audio
[Enabled]
[Enabled]
[Disabled]
[Enabled]
[Disabled]
[Enabled]
[SATA mode]
Onboard LAN
Onboard LAN Boot ROM
Onboard Lan2
Onboard LAN Boot ROM2
Onboard IEEE1394
Silicon Image Mode
Configure ITE8712 Super IO Chipset
Serial Port1 Address
Parallel Port Address
Parallel Port Mode
EPP Version
[3F8/IRQ4]
[378]
Select Screen
[EPP+ECP]
[1.9]
[DMA3]
[IRQ7]
Select Item
+- Change Option
ECP Mode DMA Channel
Parallel Port IRQ
F1
General Help
Save and Exit
Exit
F10
ESC
Onboard Game Port
Onboard MIDI Port
MIDI IRQ Select
[Enabled]
[330]
[IRQ5]
v02.58 (C)Copyright 1985-2005, American Megatrends, Inc.
HD Audio [Enabled]
Allows you to enable or disable the HD Audio feature.
Configuration options: [Disabled] [Enabled]
Onboard LAN [Enabled]
Allows you to enable or disable the onchip MAC LAN.
Configuration options: [Disabled] [Enabled]
Onboard LAN Boot ROM [Disabled]
This item allows you to enable or disable the MAC boot ROM. This item
appears only when the Onboard LAN item is set to [Enabled].
Configuration options: [Disabled] [Enabled]
Onboard LAN2 [Enabled]
Allows you to enable or disable the onchip MAC LAN2.
Configuration options: [Disabled] [Enabled]
Onboard LAN Boot ROM2 [Disabled]
This item allows you to enable or disable the MAC boot ROM2. This
item appears only when the Onboard LAN2 item is set to
[Enabled]. Configuration options: [Disabled] [Enabled]
Onboard IEEE1394 [Enabled]
Allows you to enable or disable the onboard IEEE 1394a controller.
Configuration options: [Disabled] [Enabled]
4-30
Chapter 4: BIOS setup
Silicon Image Mode [SATA mode]
Allows you to select the Silicon Image SATA controller mode.
Configuration options: [SATA mode] [RAID mode] [Disabled]
Serial Port1 Address [3F8/IRQ4]
Allows you to select the Serial Port1 base address.
Configuration options: [Disabled] [3F8/IRQ4] [2F8/IRQ3] [3E8/IRQ4]
[2E8/IRQ3]
Parallel Port Address [378]
Allows you to select the Parallel Port base addresses.
Configuration options: [Disabled] [378] [278]
Parallel Port Mode [EPP+ECP]
Allows you to select the Parallel Port mode.
Configuration options: [Normal] [EPP] [ECP] [EPP+ECP]
EPP Version [1.9]
Appears only when the Parallel Port Mode is set to [EPP] or
[EPP+ECP]. Allows you to select the parallel port EPP version.
Configuration options: [1.9] [1.7]
ECP Mode DMA Channel [DMA3]
Appears only when the Parallel Port Mode is set to [EPP+ECP]or
[ECP]. This item allows you to set the Parallel Port ECP DMA.
Configuration options: [DMA0] [DMA1] [DMA3]
Parallel Port IRQ [IRQ7]
Allows you to select the parallel port IRQ.
Configuration options: [IRQ5] [IRQ7]
Onboard Game Port [Enabled]
Allows you to enable or disable the onboard game port.
Configuration options: [Disabled] [Enabled]
Onboard MIDI Port [330]
Allows you to select the MIDI Port address or to disable the port.
Configuration options: [Disabled] [300] [330]
MIDI IRQ Select [IRQ5]
This item allows the BIOS to select the MIDI port IRQs.
Configuration options: [IRQ5] [IRQ7] [IRQ10] [IRQ11]
ASUS A8R32-MVP DELUXE
4-31
4.4.5 PCI PnP
The PCI PnP menu items allow you to change the advanced settings for
PCI/PnP devices. The menu includes setting IRQ and DMA channel resources
for either PCI/PnP or legacy ISA devices, and setting the memory size block
for legacy ISA devices.
Take caution when changing the settings of the PCI PnP menu items.
Incorrect field values can cause the system to malfunction.
BIOS SETUP UTILITY
Advanced
Advanced PCI/PnP Settings
NO: lets the BIOS
configue all the
devices in the system.
YES: lets the
operating system
configure Plug and
Play (PnP) devices not
required for boot if
your system has a Plug
and Play operating
system.
WARNING: Setting wrong values in below sections
may cause system to malfunction.
Plug And Play O/S
[No]
[64]
[Yes]
PCI Latency Timer
Allocate IRQ to PCI VGA
IRQ-3 assigned to
IRQ-4 assigned to
IRQ-5 assigned to
IRQ-7 assigned to
IRQ-9 assigned to
IRQ-10 assigned to
IRQ-11 assigned to
IRQ-14 assigned to
IRQ-15 assigned to
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
Select Screen
Select Item
+- Change Option
F1
F10
ESC
General Help
Save and Exit
Exit
v02.58 (C)Copyright 1985-2005, American Megatrends, Inc.
Plug And Play O/S [No]
When set to [No], BIOS configures all the devices in the system. When set
to [Yes] and if you install a Plug and Play operating system, the operating
system configures the Plug and Play devices not required for boot.
Configuration options: [No] [Yes]
PCI Latency Timer [64]
Allows you to select the value in units of PCI clocks for the PCI device
latency timer register. Configuration options: [32] [64] [96] [128] [160]
[192] [224] [248]
Allocate IRQ to PCI VGA [Yes]
When set to [Yes], BIOS assigns an IRQ to PCI VGA card if the card
requests for an IRQ. When set to [No], BIOS does not assign an IRQ to the
PCI VGA card even if requested. Configuration options: [No] [Yes]
IRQ-xx assigned to [PCI Device]
When set to [PCI Device], the specific IRQ is free for use of PCI/PnP
devices. When set to [Reserved], the IRQ is reserved for legacy ISA
devices. Configuration options: [PCI Device] [Reserved]
4-32
Chapter 4: BIOS setup
4.4.6 LAN Cable Status
This menu displays the status of the Local Area Network (LAN) cable
connected to the LAN (RJ-45) port.
BIOS SETUP UTILITY
Advanced
Check LAN cable
during POST.
POST Check LAN Cable
[Disabled]
LAN Cable Status
Pair
Status
Length
1-2
3-6
4-5
7-8
Open
Open
Open
Open
0.0M
0.0M
0.0M
0.0M
Select Screen
Select Item
+- Change Option
F1
General Help
F10 Save and Exit
ESC Exit
v02.58 (C)Copyright 1985-2005, American Megatrends, Inc.
POST Check LAN Cable [Disabled]
Allows you to enable or disable LAN cable check during POST. When
enabled, the menu reports the cable faults or shorts, and displays the point
(length) where the fault or short is detected. Configuration options:
[Disabled] [Enabled]
4.4.7 USB Configuration
The items in this menu allows you to change the USB-related features.
Select an item then press <Enter> to display the configuration options.
BIOS SETUP UTILITY
Advanced
USB Configuration
Module Version - 2.24.0-10.4
USB Devices Enabled:
None
USB Controller
[USB1.1+2.0]
[Auto]
[HiSpeed]
[Enabled]
Legacy USB Support
USB 2.0 Controller Mode
BIOS EHCI Hand-off
Select Screen
Select Item
+- Change Option
F1
General Help
F10 Save and Exit
ESC Exit
v02.53 (C)Copyright 1985-2005, American Megatrends, Inc.
The Module Version and USB Devices Enabled items show the
auto-detected values. If no USB device is detected, the item shows
None.
ASUS A8R32-MVP DELUXE
4-33
USB Controller [USB1.1+2.0]
Allows you to disable the USB controllers, or choose which controller to
enable. Configuration options: [Disabled ] [USB1.1 Only] [USB1.1+2.0]
Legacy USB Support [Auto]
Allows you to enable or disable support for legacy USB devices. Setting to
[Auto] allows the system to detect the presence of USB devices at
startup. If detected, the USB controller legacy mode is enabled. If no USB
device is detected, the legacy USB support is disabled.
Configuration options: [Disabled] [Enabled] [Auto]
USB 2.0 Controller Mode [HiSpeed]
Allows you to set the USB 2.0 controller mode to HiSpeed (480 Mbps) or
FullSpeed (12 Mbps). Configuration options: [FullSpeed] [HiSpeed]
BIOS EHCI Hand-off [Enabled]
Allows you to enable support for operating systems without an EHCI
hand-off feature. Configuration options: [Disabled] [Enabled]
4-34
Chapter 4: BIOS setup
4.5 Power menu
The Power menu items allow you to change the settings for the ACPI and
Advanced Power Management (APM) features. Select an item then press
<Enter> to display the configuration options.
BIOS SETUP UTILITY
Main
Advanced
Power
Boot
Exit
Suspend Mode
[Auto]
Repost Video on S3 Resume
ACPI 2.0 Support
[No]
[No]
[Enabled]
ACPI APIC Support
APM Configuration
Hardware Monitor
Select Screen
Select Item
+- Change Field
F1
General Help
F10 Save and Exit
ESC Exit
v02.58 (C)Copyright 1985-2005, American Megatrends, Inc.
4.5.1 Suspend Mode [Auto]
Allows you to select the Advanced Configuration and Power Interface (ACPI)
state to be used for system suspend. Setting this item to [Auto] allows the
OS to select the ACPI state. Configuration options: [S1 (POS) Only]
[S3 Only] [Auto]
4.5.2 Repost Video on S3 Resume [No]
Determines whether to invoke VGA BIOS POST on S3/STR resume.
Configuration options: [No] [Yes]
4.5.3 ACPI 2.0 Support [No]
Allows you to add more tables for Advanced Configuration and Power
Interface (ACPI) 2.0 specifications. Configuration options: [No] [Yes]
4.5.4 ACPI APIC Support [Enabled]
Allows you to enable or disable the Advanced Configuration and Power
Interface (ACPI) support in the Advanced Programmable Interrupt
Controller (APIC). When set to Enabled, the ACPI APIC table pointer is
included in the RSDT pointer list. Configuration options: [Disabled]
[Enabled]
ASUS A8R32-MVP DELUXE
4-35
4.5.5 APM Configuration
BIOS SETUP UTILITY
Power
Power Button Mode
[On/Off]
Restore on AC Power Loss
Power On By PS/2 Keyboard
Power On By PS/2 Mouse
Power On By RTC Alarm
[Power Off]
[Disabled]
[Disabled]
[Disabled]
[Disabled]
[Disabled]
Power On By External Modems
Power On By PCI/PCI-Ex Devices
Select Screen
Select Item
+- Change Option
F1
F10
ESC
General Help
Save and Exit
Exit
v02.58 (C)Copyright 1985-2005, American Megatrends, Inc.
Power Button Mode [On/Off]
Allows the system to go into On/Off mode or suspend mode when the
power button is pressed. Configuration options: [On/Off] [Suspend]
Restore on AC Power Loss [Power Off]
When set to Power Off, the system goes into off state after an AC power
loss. When set to Power On, the system goes on after an AC power loss.
When set to Last State, the system goes into either off or on state,
whatever the system state was before the AC power loss.
Configuration options: [Power Off] [Power On] [Last State]
Power On By PS/2 Keyboard [Disabled]
Allows you to use specific keys on the keyboard to turn on the system.
This feature requires an ATX power supply that provides at least 1A on the
+5VSB lead. Configuration options: [Disabled] [Enabled]
Power On By PS/2 Mouse [Disabled]
When set to [Enabled], this parameter allows you to use the PS/2 mouse
to turn on the system. This feature requires an ATX power supply that
provides at least 1A on the +5VSB lead. Configuration options: [Disabled]
[Enabled]
Power On By RTC Alarm [Disabled]
Allows you to enable or disable RTC to generate a wake event.
Configuration options: [Disabled] [Enabled]
4-36
Chapter 4: BIOS setup
The succeeding items appear when the Power On By RTC Alarm
item is set to Enabled.
RTC Alarm Date (Days) [Every Day]
To set the alarm date, highlight this item and press the <+> or <-> key to
make the selection.
RTC Alarm Hour (Hours) [0]
To set the alarm hour, highlight this item and press the <+> or <-> key to
make the selection.
RTC Alarm Minute (Minutes) [0]
To set the alarm minute, highlight this item and press the <+> or <-> key
to make the selection.
RTC Alarm Second (Seconds) [0]
To set the alarm second, highlight this item and press the <+> or <-> key
to make the selection.
Power On By External Modems [Disabled]
Allows either settings of [Enabled] or [Disabled] for powering up the
computer when the external modem receives a call while the computer is in
Soft-off mode. Configuration options: [Disabled] [Enabled]
The computer cannot receive or transmit data until the computer and
applications are fully running. Thus, connection cannot be made on the
first try. Turning an external modem off and then back on while the
computer is off causes an initialization string that turns the system
power on.
Power On By PCI/PCI-Ex Devices [Disabled]
When set to [Enabled], this parameter allows you to turn on the system
through a PCI LAN or modem card. This feature requires an ATX power
supply that provides at least 1A on the +5VSB lead.
Configuration options: [Disabled] [Enabled]
ASUS A8R32-MVP DELUXE
4-37
4.5.6 Hardware Monitor
BIOS SETUP UTILITY
Power
Hardware Monitor
CPU Temperature
CPU Temperature
MB Temperature
[32.5ºC/90.5ºF]
[36.0ºC/96.5ºF]
CPU Fan Speed
Chassis Fan Speed
Power Fan Speed
[3813 RPM]
[N/A]
[N/A]
VCORE Voltage
3.3V Voltage
5V Voltage
[ 1.320V]
[ 3.345V]
[ 5.094V]
[11.880V]
Select Screen
12V Voltage
Select Item
+- Change Option
CPU QFan Control
[Disabled]
[Disabled]
F1
General Help
Save and Exit
Exit
F10
ESC
Chassis QFan Control
v02.53 (C)Copyright 1985-2004, American Megatrends, Inc.
CPU Temperature [xxxºC/xxxºF]
MB Temperature [xxxºC/xxxºF]
The onboard hardware monitor automatically detects and displays the
motherboard and CPU temperatures. Select [Ignored] if you do not wish to
display the detected temperatures.
CPU Fan Speed [xxxxRPM] or [Ignored]
The onboard hardware monitor automatically detects and displays the CPU
fan speed in rotations per minute (RPM). If the fan is not connected to the
motherboard, the field shows N/A. Select [Ignore] from the item options to
disable CPU fan speed monitoring.
Chassis Fan Speed N/A] or [Ignored]
The onboard hardware monitor automatically detects and displays the
chassis fan speed in rotations per minute (RPM). If the fan is not connected
to the chassis, the specific field shows N/A. Select [Ignore] from the item
options to disable chassis fan speed monitoring.
Power Fan Speed [N/A] or [Ignored]
The onboard hardware monitor automatically detects and displays the
power fan speed in rotations per minute (RPM). If the fan is not connected
to the power fan connector, the specific field shows N/A.
VCORE Voltage, 3.3V Voltage, 5V Voltage, 12V Voltage
The onboard hardware monitor automatically detects the voltage output
through the onboard voltage regulators.
4-38
Chapter 4: BIOS setup
|