USER MANUAL
High Definition Multimedia
Pure Flat Monitor
DM-5952KF / DM-6952KF
A73110002790
12. Never push objects of any kind into this product through cabinet slots as
they may touch dangerous voltage points or short out parts that could
result in a frisk of fire or electric shock. Never spill liquid of any kind on
the product.
2. SAFETY INSTRUCTIONS
1. Read all of these instructions.
13. Do not attempt to service this product yourself, as opening or removing
covers may expose you to dangerous voltage points or other risks. Refer
all servicing to qualified service personnel.
2. Save these instructions for later use.
3. Follow all warnings and instructions marked on the product.
14. Unplug this product from the wall outlet and refer servicing to qualified
service personnel under the following conditions:
4. Unplug this product from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth for cleaning.
5. Do not use this product near water.
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the product.
6. Do not place this product on an unsuitable cart, stand or table; the product
may fall causing damage or injury.
c. If the product has been exposed to rain or water.
7. Slots and openings in the cabinet and the back or bottom are provided for
ventilation. To ensure reliable operation of the product and to protect it
from overheating, these openings must not be blocked or covered.
Placing the product on a bed, sofa, rug, or other similar surface should
never block the openings. This product should never be placed near or
over a radiator or heat register. This product should not be placed in a
built-in installation unless proper ventilation is provided.
d. If the product does not operate normally when the operating
instructions are followed. Adjust only those controls that are covered
by the operating instructions since improper adjustment of other
controls may result in damage and will often require extensive work by
a qualified technician to restore the product to normal operation.
e. If the product has been dropped or the cabinet has been damaged.
8. This product should be operated from the type of power source indicated
on the marking label. If you are not sure what type of power available,
consult your dealer or local Power Company.
f. If the product exhibits a distinct change in performance, indicating a
need for service.
9. This equipment is to be electrically grounded. This product is equipped
with a three-wire plug with a third (grounding) pin. This plug will only fit
into a grounded AC outlet. This is a safety feature. If you are unable to
insert the plug into the outlet, contact a licensed electrician to replace the
outlet with a properly grounded outlet. Do not defeat the purpose of the
grounding plug!
10. Do not allow anything to rest on the power cord. Do not locate this
product where persons will walk on the cord.
11. If an extension cord is used with this product, make sure that the total of
the ampere ratings on the products plugged into the extension cord does
not exceed the extension cord ampere rating. Make sure that the total of
all products plugged into the wall outlet does not exceed 15 amperes.
2
3
USING WITH A LAPTOP
3. README FIRST
If you are using Notebook;Press Fn. + F5 (or Fn. + F3) to output the display
These easy start-up tips will guide you in making the connections to get you
up and running.
to CRT only (CRT output combination key might be different on every
notebook), or press combination key again to show on both CRT and LCD
display.
USING WITH A DESKTOP PC OR LAPTOP
1. Prior to connecting the monitor, if you have a desktop monitor connected to
your PC, please insure that the video card refresh rate is set within the
USING WITH A MAC
1. Plug the AC power cord from the power source (outlet) to the AC input of
Monitors frequency range by going to:
our monitor.
2. Connect the MAC adapter to the MAC monitor output (if required the MAC
model). Refer to the adapter user’s manual for the proper dipswitch settings.
The optimum setting for the monitor is a resolution setting of 800ɰ600 and
Start…Settings…Control
Panel…Display…Settings…Advanced…Adapter.
Set the Adapter refresh rate to 60Hz or “Adapter Default”. This applies to
a refresh rate of 60Hz. Make sure the display settings of the MAC is set to
800ɰ600 at 60Hz as well.
the three supported resolutions of 640×480, 800×600 and 1024×768.
Otherwise, the monitor will not display and the unit will go into
standby mode (Yellow-orange LED).
Note:You need a MAC adapter when using the monitor with older MAC
Computers. The MAC adapter converts the output to VGA HD-15 pin
out. This adapter is available at an additional cost.
2. Plug the AC power cord from the power source (outlet) to the AC input of
the monitor.
3. Connect the VGA cable provided from your computer’s VGA output to the
input on the monitor.
3. Connect the VGA cable from the monitor to the MAC adapter.
VGA 1 VGA 1 input port located in the rear of the monitor.
VGA 2 VGA 2 input port located in the front of the monitor.
Note:Be sure the PC is powered on before the monitor.
Press the VGA1∕VGA2 select button, located next to the front VGA
connector and on the Remote Control until the computer image is
displayed.
SIMULTANEOUS VIEWING OF THE MONITOR AND STANDARD PC
MONITORS
Connect the VGA cable from the PC’s VGA output to the VGA input. Then
plug the desktop monitor’s VGA cable to the monitor VGA output.
4
5
5. WITH【CT-1871】VISION CONVERTER
4. WITHOUT VISION CONVERTER
Note:Only for Rev.K-1 or higher.
FIGURE 1:DM-XX52KF W/O VISION CONVERTER CONNECTION
FIGURE 2:DM-XX52KF CONNECT WITH CT-1871 VISION CONVERTER
6
7
7. INSTALLATION
6. WITH【CT-1890∕CT-1892】VISION CONVERTER
Precautions
Note:Only for Rev.K-1 or higher.
Monitor shall be placed at least 6 inches away from the obstructer.
a. Monitor will work well when connect with computer and any high
definition receiver. With a high definition resolution, Monitor is designed
without video converter with it. To work as a TV or using with VCR and
DVD, you must to connect with a video converter.
b. The following descriptions are based on Monitor connected with video
converter ready. 【See Figure 2 ~ 3】
Television
1. Install cable from antenna or cable TV to the “F” connector labeled “ANT
IN”.
2. Press the Power ON, and the Red LED Indicator should be lit on the
monitor, and the monitor is on STAND BY mode.
3. Press the POWER button on the Remote-controller; the Red indicator
should turn into green.
4. Press TV∕PC∕AV button or press TV button on Remote-Controller
until the monitor displays MAIN NTSC TV.
5. To switch to TV∕CATV mode, select TV if you are using an antenna, or
select CATV if you have a cable service.
6. Press AUTO button with your remote control, and Monitor will now
preset all active channels into memory.
7. Selecting a channel.
a. Press CH▲∕▼to select channels on Remote control or on the front
panel
.
FIGURE 3:DM-XX52KF CONNECT WITH CT-1890/CT-1892 VISION CONVERTER
b. Press the numeric key to select a desired channel.
8. Press VOL +∕VOL - to adjust the volume on remote control or the front
panel.
Video Recorder (VCR)
1. To connect the signal by F Connector, following the instruction to setup
your Television.
2. If using the Video (Composite) from the VCR, connect the Video input
with Left, and Right Speaker.
3. Start the VCR.
4. Using the Remote control press TV∕PC∕AV button until or press
VIDEO button until VIDEO appears on the screen.
5. If using the S-Video output of the VCR. Connect an S cable from the
VCR to Monitor.
8
9
High Definition Receiver
6. Connect the Left and the Right audio channel to monitor.
7. Start the VCR.
1. If your HD receiver has a VGA connector, it can be used to input monitor.
2. Connect a Receiver to the monitor using the VGA1 located on the rear
panel or VGA2 located on the front panel.
8. Press the TV∕PC∕AV button or press S-VHS button by remote control
until S-VHS appears on the screen.
3. Connect the Audio to appropriate audio connectors next to the VGA
connector.
DVD player
4. Using the Remote control, press the TV∕PC∕AV button or press VGA1
∕VGA2 button until VGA1∕VGA2 appears on the screen.
5. Press MENU, then press the right arrow key on the picture to adjust the
geometry controls for a good picture.
6. If using the component output of the DVD, connect an component video
cable from the DVD with monitor.
7. Connect the left with the right audio channel.
8. Start the DVD player.
9. Using the Remote Control, press the TV ∕ PC ∕ AV button or the
Component button until Y,Cb,Cr∕Y,Pb,Pr appears on the screen.
1. Connect the Video input with Left and Right speaker on DVD.
2. Start the DVD player.
3. Press the TV∕PC∕AV button or press VIDEO button by Remote
control until VIDEO appears on the screen.
4. If using the S-Video output of the DVD, connect an S cable from the
DVD with monitor.
5. Connect the Left with the Right audio channel.
6. Start the DVD player.
7. Press TV∕PC∕AV button or S-VHS button until appears on the screen.
8. If using the component output of the DVD, connect a component video
cable from the DVD with monitor.
9. Connect the left with the right audio channel.
10. Start the DVD player.
11. Using the Remote Control, press the TV ∕ PC ∕ AV button or the
Component button until Y, Cb, Cr∕Y, Pb, Pr appears on the screen.
Computer
1. Connect the computer with the monitor by using VGA1 that located on
the rear panel, or VGA2 that located on the front panel.
2. Connect the Audio to the appropriate audio connector next to the VGA
connector.
3. Press the TV∕PC∕AV button or press VGA1∕VGA2 button until
VGA1 ∕VGA2 appears on the screen.
4. If monitor has no display, check your video card on the appendix B.
5. If there is no display on the screen, verify if the proper input VGA1∕
VGA2 has been manually selected.
10
11
8. USING THE MONITOR
POWER
(Toggle) Starts or stops the monitor function.
DEGAUSS
(PC⁄TV⁄AV)
This is a dual function key:
This section describes how to use and make adjustments to the monitor. It
also provides a reference to the control panel and the remote control.
a. Switch the input source through TV∕PC∕VIDEO∕S-
Video ∕COMPONENT∕TV while connect with a vision
converter.
Using the Control Panel
b. Press this key to execute degaussing while in normal
status. Each degauss is lasting for 4 seconds, and
waiting for 5 minutes to re-do degauss.
Using control panel to control the monitor instead of the remote control.
However, some other functions are not set on control panel. There are 7 panel
keys, and following lists the function buttons on the control panel:
MENU
(Toggle) Enables/Disables the on-screen display menu, or
return to the upper level menu in the menu mode.
SEL+∕CH+
This is a dual function key:
a. Press SEL
+∕
-
to serve as menu item selection.
SEL-∕CH-
b. Press CH+∕- to adjust the channel.
DM-XX52KF VGA2 IN & PANEL KEYS
Note:
Indicators
When you are adjusting a function under the magnitude bar, you may also
adjust other items in the same group by pressing the up∕down keys. Don’t
go back to the previous menu by way of the MENU key.
a. Power LED shows power on∕off, and power saving status.
b. Stereo LED is lit when the TV programs being received.
c. SAP LED is lit when the program is broadcast in Sub-audio.(2nd audio
program)
VOL+∕-
This is a dual function key:
a. Press VOL+ ∕-to control volume in any mode, except
Power LED
Green
Stereo LED
Stereo On (Red)
Mono Off
SAP LED
in menu function.(optional)
Normal on
Stand by
Main Audio Off
b. Press VOL+ ∕-to control the selection function while
Amber
Red
Sub Audio On (Yellow)
in menu mode.
Suspend∕Active off
Power off
Select TV or CATV pair as inputs. While in the TV/CATV
mode; the VGA 1∕VGA 2 key serves as TV∕CATV key.
TV∕CATV
Red
(VGA 1∕VGA2)
TABLE 1:INDICATOR OPERATION DESCRIPTION
Note
:
Auto-switch function : On VGA mode, upon POWER-ON, and at
POWER-ON only, the monitor will automatically switch to the other port
when NO signal appears after 8 seconds. On other words, VGA1 will
switch to VGA2, and vice versa. But if ports have NO input, this monitor
will switch back to the original default port.
12
13
|