6100_book_1ATT 11/25/00 12:37 PM Page ii
USER’S MANUAL
Part 2
900 MHz Cordless
Telephone 6100
DRAFT
11/25/00
Please also read
Part 1 — Important
Product Information
AT&T and the globe symbol are registered trademarks of AT&T Corp. licensed to Advanced AmericanTelephones.
6100_book_1ATT 11/25/00 12:37 PM Page 1
CONTENTS
INSTALLATION . . . . . . . . . . . . . . . . . . . . 3
Before You Install . . . . . . . . . . . 3
Table/Desk Installation . . . . . . 4
Wall Installation . . . . . . . . . . . . 6
TELEPHONE MEMORY . . . . . . . . 12
Store Memory Numbers . . . . . 12
Change/Replace a Stored
Memory Number . . . . . . . . 12
Dial Memory Numbers . . . . . 12
Store a Pause in a
Memory Number . . . . . . . . 12
Directory Label . . . . . . . . . . . 12
TELEPHONE OPERATION . . . . . 8
Make or Answer a Regular
Phone Call . . . . . . . . . . . . . . 8
Access Internet Calling . . . . . . 8
Redial . . . . . . . . . . . . . . . . . . . 8
Change Channel . . . . . . . . . . . 8
Handset Volume . . . . . . . . . . . . 8
Flash/Call Waiting . . . . . . . . . . 8
Page/Handset Locator . . . . . . . 9
Making Internet Calls . . . . . . . 10
Handset Ringer Style . . . . . . . 10
Ringer Off/Battery Save . . . . . 10
Headset Jack . . . . . . . . . . . . . 11
Operating Range . . . . . . . . . . 11
BATTERIES . . . . . . . . . . . . . . . . . . . . . . . . 13
Charging the Handset
Battery Pack . . . . . . . . . . . . 13
Replacing the Handset
Battery Pack . . . . . . . . . . . . 14
IN CASE OF DIFFICULTY . . . . . . 15
1
6100_book_1ATT 11/25/00 12:37 PM Page 3
INSTALLATION
Before You Install
1
Choose a location for the base near an electrical outlet and
a telephone jack.
This phone requires a modular telephone jack and a standard
electrical outlet (110v AC) not controlled by a wall switch.
2
Install the handset battery.
b) Align two holes in
a) Remove battery
compartment
cover by pressing
on the
plug with socket
pins, and snap the
plug into place.
indentation
and sliding
downward.
c) Place battery pack in compartment
with the wires in the lower left
corner, along the bottom of the
battery pack.
d) Replace cover by sliding
it up into place.
3
Attach the belt clip to the cordless handset (optional).
To attach
To remove
3
6100_book_1ATT 11/25/00 12:37 PM Page 4
INSTALLATION
Table/Desk Installation
Standard
electrical outlet
Modular
telephone
jack
1 Connect the
telephone line
cord.
3 Connect microphone
and speaker cords.
2 Connect the power cord.
4
6100_book_1ATT 11/25/00 12:37 PM Page 5
INSTALLATION
Standard
electrical outlet
Modular
telephone
jack
1 Connect the
telephone line
cord.
3 Connect microphone
and speaker cords.
2 Connect the power cord.
4
5
Charge the handset battery.
Place the handset in the base. Charge the battery for at least 24 hours
the first time. After the first charge, the battery is typically fully
charged overnight.
Check for dial tone.
After the batteries are charged, pick up the handset and press P;
you should hear a dial tone.
5
6100_book_1ATT 11/25/00 12:37 PM Page 6
HINESATDALILNAETILOENFT
Wall Installation
1
Position the wall mount adapter on the base.
Align tabs on wall
mount adapter with
holes on bottom of
base. Snap wall
mount adapter firmly
into place.
2
3
Connect the telephone line cord.
Connect the power cord.
6
6100_book_1ATT 11/25/00 12:37 PM Page 7
INSTALLATION
4
Mount the base on the wall.
a) Align holes
on base with
mounting
studs on
wall jack.
b) Place power
cord as shown,
so it hangs
straight down
between base
and wall.
c) Connect cords
to computer.
d) Pull base down
on mounting
For more detailed
computer hookup up
see pages 4 and 5.
studs until it
locks into place.
5
Follow Steps 4–5 in Table/Desk Installation.
7
6100_book_1ATT 11/25/00 12:37 PM Page 8
TELEPHONE OPERATION
Handset Volume
Adjust volume of
what you hear
through the handset.
Flash/
Call Waiting
Access special
telephone
company
subscriber
services.
Make or Answer
a Regular
Access
Internet
Calling
Phone Call
Lift handset
from base
— OR —
Press P and
wait for light to
go on steadily.
Redial
Follow the
instructions
Red:
Regular phone call
in progress.
under“Make or
Answer a
Regular Phone
Call,”then press
R to call the
last number
Green:
Internet phone call
in progress.
Red and Green
or yellow):
Regular call and
clearer channel
internet call in progress
while on a call.
Change Channel
dialed (up to
24 digits).
Switch to a
8
6100_book_1ATT 11/25/00 12:37 PM Page 9
TELEPHONE OPERATION
On steadily
when handset
is in base
Page/
Handset Locator
Press once to page
the handset for up
to one minute
— OR —
Press twice
to cancel.
9
6100_book_1ATT 11/25/00 12:37 PM Page 10
HTEELAEDPLHINOENELEOFPTERATION
Making Internet Calls
•
Follow your internet calling provider’s directions to establish a call.
Then press
If you receive a regular call while you’re on an internet call, press
p to take the call. Press to return to your internet call.
to connect the call to your handset.
Handset Ringer Style
You can select from four different handset ringer styles.
1
2
3
Make sure the handset is off.
Press g, #.
Press 1, 2, 3 or 4 to select your ringer style. You will hear a
sample of the ringer style.
4
Press g.
Ringer Off/Battery Save
1
2
3
4
5
Make sure the handset is off.
Press g, #.
Press 5.
Press g.
To turn the ringer on again, see Handset Ringer Style.
10
6100_book_1ATT 11/25/00 12:37 PM Page 11
TELEPHONE OPERATION
Headset Jack
You can use this telephone
hands-free when you install a
2.5 mm headset (SKU 24099),
purchased separately.
Plug the headset into the jack
located on the right side of
the handset (under the small
rubber flap). Do not force
the connection, but make sure
the plug fits securely.
Operating Range
This cordless telephone operates within the maximum power allowed by
the Federal Communications Commission (FCC). Even so, this handset and
base can communicate over only a certain distance — which can vary with
the locations of the base and handset, the weather, and the construction of
your home or office. For best performance, keep the base antenna fully
upright.
If you receive a call while you are out of range, the handset might not
ring — or if it does ring, the call might not connect when you press P.
Move closer to the base, then press P to answer the call.
If you move out of range during a phone conversation, you might
hear noise or interference. To improve reception, move closer to the base.
If you move out of range without pressing O, your phone will be
left“off the hook.” To hang up properly, walk back into range, periodically
pressing O.
11
6100_book_1ATT 11/25/00 12:37 PM Page 12
HTEELAEDPLHINOENELEMFTEMORY
This cordless phone can store 10 telephone numbers, each up to 16 digits
long. You can dial numbers stored in memory just by pressing g and
a number button.
Store Memory
Numbers
1 Make sure the
handset is off.
2 Press g.
The PHONE light
blinks.
3 Press the number
button (0–9) where
you want to store
the telephone
number.
4 Dial the telephone
number (up to 16
digits)
— OR —
Press R to
store the last
number dialed.
Store a Pause
in a Memory
Number
Press to store a
two-second
pause in the
dialing sequence.
Each press adds
another two-
second pause
and counts as
one digit.
5 Press g.
Change/Replace
a Stored Memory
Number
Store a new number
in its place.
Directory Label
Use the self-
adhesive directory
label to keep a
record of the
Dial Memory
Numbers
1 Press P.
numbers (or
2 Press and release
g, then press
the number button
(0–9) where the
memory number is
stored.
names) stored in
memory. It’s best
to write on the
label before
applying it to the
phone.
12
6100_book_1ATT 11/25/00 12:37 PM Page 13
BATTERIES
Charging the Handset Battery Pack
This battery should remain charged up to six days with the ringer turned
on and up to 12 days with the ringer off. A fully charged battery provides
an average talk time of about six hours.
The battery pack needs charging when:
•
•
•
A new battery is installed in the handset.
The phone beeps twice when you press P.
The phone light flashes slowly.
Place the handset in the base so the CHARGING light turns on. The battery
pack is typically fully charged in eight hours.
You can keep the battery fully charged by returning the handset to the
base after each use.
If you repeatedly get a low battery indicator, even after eight hours
of charging, the battery should be replaced.
13
6100_book_1ATT 11/25/00 12:37 PM Page 14
HBAETATDELRINIEESLEFT
Replacing the Handset Battery Pack
1
Remove the battery compartment cover on the handset by
pressing on the indentation and sliding the cover downward.
2
3
Lift out the old battery pack and disconnect.
Align the two holes in the new battery pack’s plug with the
socket pins, and snap the plug into place. Place the battery pack in the
compartment with the wires in the lower left corner, along the bottom
of the battery pack.
4
5
Replace the cover by sliding it up into place.
The new battery pack must be charged before using the phone.
Place the handset in the base and allow it to charge for at least
24 hours the first charge. The telephone might operate before that,
but for best performance, let the battery pack charge fully.
14
6100_book_1ATT 11/25/00 12:37 PM Page 15
IN CASE OF DIFFICULTY
If you have difficulty operating this phone, try the suggestions below.
1 800 222–3111. Please retain your receipt as your proof of purchase.
If the phone doesn’t work at all, check these items first:
•
Make sure the AC adapter is plugged into an outlet not controlled
by a wall switch.
•
Make sure the telephone line cord is plugged firmly into the base
unit and the modular jack.
•
•
Make sure the base antenna is fully upright.
If the handset does not beep when you press P, the battery
might need charging.
•
Make sure the battery pack is installed correctly.
If the above suggestions don’t solve the problem, try re-initializing
the handset and base:
1
2
3
4
5
6
Disconnect the power to the base.
Remove the handset battery pack.
Wait a few minutes.
Connect the power to the base.
Insert the handset battery pack.
Put the handset in the base to re-initialize.
If you hear a two-beep signal when you try to use the handset:
•
You might be out of range. Move closer to the base and try again.
•
If moving closer to the base doesn’t help, try following the directions
above for re-initializing the handset and base.
If the phone does not ring when you receive a call:
•
Make sure the handset ringer is on.
•
Make sure the telephone line cord is connected firmly to the base
and the telephone jack.
•
Make sure the AC adapter is plugged firmly into an outlet not
controlled by a wall switch.
•
•
You might be too far from the base; move closer.
You might have too many extension phones on your telephone line
to allow all of them to ring. Try unplugging some of them.
15
6100_book_1ATT 11/25/00 12:37 PM Page 16
HINEACDASLEINOEFLDEIFFTFICULTY
If you hear noise or interference when using the phone:
•
•
•
Make sure the base antenna is fully upright.
You may be out of range. Move closer to the base.
Press and release C to change to another of the 30 channels
available. If noise is exceptionally loud, move closer to the base before
changing channels.
•
•
•
Household appliances plugged into the same circuit as the base can
sometimes cause interference. Try moving the appliance or the base to
another outlet.
The layout of your home or office might be limiting the operating
range. Try moving the base to another location, preferably on an
upper floor.
If the buttons don’t work, try placing the handset in the base for at
least 15 seconds.
If you hear other calls while using your phone:
•
Press C to change to another channel.
•
Disconnect the base from the modular jack and plug in a corded
telephone. If you still hear other calls, the problem is probably in your
wiring or local service. Call your local telephone service company.
If you lose a call after changing channels:
You were probably almost out of range. Move closer to the base before
changing channels. Before placing another call, set the handset in the base
for at least 15 seconds.
16
|