PPC-L106T
AMD LX800 processor-based
Panel PC with 10.4" TFT LCD flat
panel display
User Manual
FCC Class B
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interfer-
ence when the equipment is operated in a residential environment. This
equipment generates, uses and can radiate radio frequency energy. If not
installed and used in accordance with this user manual, it may cause
harmful interference to radio communications. Note that even when this
equipment is installed and used in accordance with this user manual, there
is still no guarantee that interference will not occur. If this equipment is
believed to be causing harmful interference to radio or television recep-
tion, this can be determined by turning the equipment on and off. If inter-
ference is occurring, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and the receiver
• Connect the equipment to a power outlet on a circuit different from that
to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
Warning! Any changes or modifications made to the
equipment which are not expressly approved by
the relevant standards authority could void your
authority to operate the equipment.
iii
Packing List
Before you begin installing your card, please make sure that the following
materials have been shipped:
• PPC-L106T series panel PC
• Accessories for PPC-L106T
- Keyboard extension cable (5-pin DIN female to 6-pin PS/2 male)
- HDD flat cable (44-pin) (8 cm)
- Power cord (1.8 m) - USA type
- HDD bracket
- Driver/Utility CD-ROM disk
- Screws
- Warranty card
If any of these items are missing or damaged, contact your distributor or
sales representative immediately.
Additional Information and Assistance
Step 1. Visit the our web site where you can find the latest
information about the product.
Step 2. Contact your distributor, sales representative, or customer
service center for technical support if you need additional
assistance. Please have the following information ready before
you call:
• Product name and serial number
• Description of your peripheral attachments
• Description of your software (operating system, version, application
software, etc.)
• A complete description of the problem
• The exact wording of any error messages
PPC-L106T User Manual
iv
Safety Instructions
1. Please read these safety instructions carefully.
2. Please keep this User Manual for later reference.
3. Please disconnect this equipment from any AC outlet before cleaning. Do not
use liquid or spray detergents for cleaning. Use a damp cloth.
4. For pluggable equipment, the socket-outlet must be installed near the equip-
ment and must be easily accessible.
5. Please keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or let-
ting it fall could cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment
from overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not place anything
over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power
source to avoid damage by transient overvoltage.
12. Never pour any liquid into an opening. This could cause fire or electrical
shock.
13. Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
14. If one of the following situations arises, get the equipment checked by service
personnel:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment does not work well, or you cannot get it to work according
to the user manual.
e. The equipment has been dropped and damaged.
f. The equipment has obvious signs of breakage.
15. DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED ENVI-
RONMENT WHERE THE STORAGE TEMPERATURE MAY GO
BELOW -20° C (-4° F) OR ABOVE 60° C (140° F). IT MAY DAMAGE
THE EQUIPMENT.
The sound pressure level at the operator's position according to IEC 704-
1:1982 is equal to or less than 70 dB(A).
DISCLAIMER: This set of instructions is supplied according to IEC 704-
1. We disclaim all responsibility for the accuracy of any state-
ments contained herein.
v
Wichtige Sicherheishinweise
1. Bitte lesen sie Sich diese Hinweise sorgfältig durch.
2. Heben Sie diese Anleitung für den späteren Gebrauch auf.
3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie
Keine Flüssig-oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch
zur Reinigung.
4. Die NetzanschluBsteckdose soll nahe dem Gerät angebracht und leicht
zugänglich sein.
5. Das Gerät ist vor Feuchtigkeit zu schützen.
6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen
oder Fallen könnte Verletzungen hervorrufen.
7. Die Belüftungsöffnungen dienen zur Luftzirkulation die das Gerät vor überhit-
zung schützt. Sorgen Sie dafür, daB diese Öffnungen nicht abgedeckt werden.
8. Beachten Sie beim. AnschluB an das Stromnetz die AnschluBwerte.
9. Verlegen Sie die NetzanschluBleitung so, daB niemand darüber fallen kann.
Es sollte auch nichts auf der Leitung abgestellt werden.
10. Alle Hinweise und Warnungen die sich am Geräten befinden sind zu
beachten.
11. Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten Sie es vom
Stromnetz trennen. Somit wird im Falle einer Überspannung eine Beschädi-
gung vermieden.
12. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüssigkeiten
in das Gerät gelangen. Dies könnte einen Brand bzw. elektrischen Schlag aus-
lösen.
13. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen
Sicherheit nur von authorisiertem Servicepersonal geöffnet werden.
14. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu trennen
und von einer qualifizierten Servicestelle zu überprüfen:
a - Netzkabel oder Netzstecker sind beschädigt.
b - Flüssigkeit ist in das Gerät eingedrungen.
c - Das Gerät war Feuchtigkeit ausgesetzt.
d - Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktioniert
oder Sie mit Hilfe dieser Anleitung keine Verbesserung erzielen.
e - Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.
f - Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.
15. VOSICHT: Explisionsgefahr bei unsachgemaben Austausch der Batte-
rie.Ersatz nur durch densellben order einem vom Hersteller empfohlene-
mahnlichen Typ. Entsorgung gebrauchter Batterien navh Angaben des
Herstellers.
Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000
beträgt 70dB(A) oder weiger.
DISCLAIMER: This set of instructions is supplied according to IEC704-
1. We disclaim all responsibility for the accuracy of any state-
ments contained herein.
PPC-L106T User Manual
vi
PPC-L106T User Manual
viii
1
General Information
This chapter gives background
information on the PPC-L106T.
Sections include:
•
•
•
•
•
•
•
Introduction
Specifications
LCD Specifications
Dimensions
I/O Arrangement
Cutout (Suggestion)
Mounting
Chapter 1 General Information 1
Chapter 1 General Information
1.1 Introduction
The PPC-L106T is a 10.4" LCD Panel PC with an AMD LX800 CPU that
is designed to serve as a human machine interface (HMI). It is a PC-based
system with 10.4" color TFT LCD display, on-board PCI Ethernet, multi-
COM port interfaces, and a 16-bit audio controller. This simple, com-
plete, compact and highly integrated multimedia system lets you easily
build a panel PC into your applications. By incorporating the PPC-L106T
into your project, your product development time will be shortened.
The PPC-L106T is a compact, network-compatible PC with extensive
features to control a dedicated system in a wide variety of applications.
Common industrial applications include factory automation systems, pre-
cision machinery, and production process control. It is also suitable for
many nonindustrial applications, including terminal information systems,
entertainment management systems, and car park automation systems.
Our panel PC is a reliable, cost-effective solution to your application's
processing requirements.
1.2 Specifications
General
•
Dimensions (W x H x D): 342 x 265 x 92.4 mm
(13.5"x10.4"x3.6")
•
•
Weight: 3.2 kg (7.1 lbs)
Power supply:
AC model: 65 watts
Input voltage: 100 ~ 240Vac, 2A, 50 ~ 60 Hz
Output voltage: +5 V @ 3.5 A, +12 V @ 4 A
•
•
•
Safety: UL/CB/CCC/BSMI approved
Disk drive housing: Space for one internal 2.5" HDD
Front panel protection: IP 65/NEMA 4 compliant
Standard PC functions
•
•
•
CPU: AMD LX800 (500 MHz) processor on board
BIOS: AWARD 4M bit Flash BIOS, supports Plug & Play, APM v1.2
Chipset: AMD CS 5536
2 PPC-L106T User Manual
•
•
2nd level cache: 128 KB on CPU
RAM: One 200-pin SODIMM sockets accept 256 ~ 1024 MB
DDR
•
PCI Bus Master IDE interface: Supports two connectors (one
internal, one external). Each connector supports two IDE
devices on two channels (PIO modes 3/4). BIOS supports IDE
(PIO mode 0~4, DMA mode 0~2, and Ultra DMA33 simulta-
neously). Default: CF Slot set as Master
•
•
Parallel port: One parallel port, supports SPP/EPP/ECP parallel
mode.
Serial ports: Four serial ports with three RS-232 ports (COM1, 3,
and 4), one RS-232/422/485 port (COM2). All ports with
16C550 compatible UARTs. Default COM4 reserved for Touch
•
•
USB: Supports four USB 2.0 (2 x internal, 2 x external)
PCI/ISA bus expansion slot: Accepts either one ISA or one PCI
bus card.
•
•
Watchdog timer: 256-level interval from 1 to 255 seconds.
Jumperless selection and software enabled/disabled.
Battery: 3 V @ 195 mA lithium battery for CMOS backup
Solid State Disk (SSD)
One 50-pin socket: for one CompactFlash™ Type II storage card,
shared with one IDE channel.
PCI SVGA/flat panel interface
•
•
•
•
•
Chipset: AMD CS 5536
Display memory: 1.5~4 MB share memory
Display type: Simultaneously supports CRT and flat panel displays
Display resolution: Supports non-interlaced CRT and LCD dis-
plays up to 800 x 600 @ 256 K colors with 1.5~4 MB shared
memory
Audio function:
Audio Chipset: ALC203, fully compliant AC 97 analog I/O com-
•
ponent, 16-bit stereo full-duplex codec, audio interface for
microphone-in, line-in and speaker out
PCI bus Ethernet interface
Chapter 1 General Information 3
•
Ethernet Chipset: Realtek RTL8100C PCI local bus Ethernet con-
troller fully compliant with IEEE 802.3u 10/100 Base-T speci-
fications.
Touchscreen (optional)*
Type
Analog Resistive
Infrared
Continuous
4096 x 4096
Resolution
Light Transmission
Controller
80%
91%
RS-232 interface
(uses COM4)
Optional USB
interface
<5 V @ 200 mA
5 V @ 100 mA
Power Consumption
Software Driver
Supports Windows CE Supports Windows CE
/XP
/XP
35 million
100,000 hrs
Durability (touches
in a lifetime)
*Note: The PPC-L106T with the optionally installed touchscreen will
share COM4.
Environment
•
•
•
•
•
Temperature: 45° C (32 ~ 125° F)
Relative humidity: 10 ~ 95% @ 40° C, non-condensing
Shock: 10G peak acceleration (11 msec duration)
Power MTBF: 50,000 hrs
Certification: CE, FCC Class B, BSMI, CCC
4 PPC-L106T User Manual
1.3 LCD Specifications
Default
Optional
10.4" SVGA TFT
10.4" SVGA TFT
Display type (LCD)
Max. resolution
Colors
800 x 600
262 K colors
120 / 100
0.264 X 0.264
230
800 x 600
262 K colors
140 / 100
0.264 X 0.264
400
View angle
Dot size (mm)
Luminance (cd/mð)
Temperature (°C)
VR controls
0 ~ 50
0 ~ 50
Yes*
Yes*
Yes
Yes
Simultaneous mode
Lamp Life (hrs)
20,000 hours
50,000 hours
* The VR control is defined by hot key in DOS or BIOS mode as follows:
Ctrl-Alt-F3, Ctrl-Alt-F4
Chapter 1 General Information 5
1.4 Dimensions
Figure 1.1: PPC-L106T panel PC dimensions
6 PPC-L106T User Manual
1.5 I/O Arrangement
Figure 1.2: PPC-L106T back panel I/O arrangement and cable connec-
tions
A. Power switch
B. Parallel port
F. COM ports
G. COM ports
H. VGA port
C. PS/2 mouse connector
D. Mic-in/Line-out
E. AC inlet
I. USB ports V2.0
J. Ethernet
* Three RS-232 (COM1, 3, 4) and one RS-232/422/485 (COM2)
Chapter 1 General Information 7
1.6 Cutout (Suggestion)
The PPC-L106T will stand on a shelf or a table, or you can mount it into
a panel. Cutout panel dimensions are as follows
Figure 1.3: PPC-L106T panel mounting cutout
dimensions
8 PPC-L106T User Manual
1.7 Mounting
1.7.1 Panel mounting
If you decide to use a cutout within a panel to mount your PPC-L106T,
we have included two panel-mount brackets. The brackets have two
screws that fit in the keyhole slots on the panel PC.
Slide the PPC-L106T backwards into the panel opening. Attach the two
mounting brackets by sliding the two screw heads into the keyhole slots
on the rear cover. Secure the PPC-L106T against the back of the panel
opening.
Figure 1.4: PPC-L106T rear panel mounting brackets
Chapter 1 General Information 9
1.7.2 Desktop stand (optional)
An optional stand is available for mounting the PPC as a desktop PC. The
PPC-L106T slides into the stand and is held in place by the screws pro-
vided. The compactness of the desktop-mounted PPC-L106T saves desk
space.
Figure 1.5: PPC-L106T desktop stand
10 PPC-L106T User Manual
1.7.3 Wall-mounting (optional)
An optional wall-mounting attachment is also available for mounting the
PPC at approximately 45° to a flat surface. Installation instructions fol-
low:
1.
2.
3.
The wall-mounting attachment is comprised of three parts: one
back bracket, one support bracket, and one mounting bracket.
First attach the back bracket to the rear cover of the PPC-L106T,
securing it in place with four of the philips-head screws provided.
Using a flat-head screwdriver, attach the support bracket to the
back bracket using four of the flat-head screws provided, two on
either side of the support bracket. The sides of the support bracket
should overlap the sides of the back bracket, and the screws should
secure one bracket to the other through the existing holes drilled
into each bracket.
4.
Mount the mounting bracket on the wall or other flat surface. The
support bracket slides vertically from the top into the mounting
bracket. It can then can be secured to the mounting bracket by
screwing one of the philips-head screws provided through the cor-
responding holes at the tops of the mounting bracket and the sup-
port bracket.
Figure 1.6: PPC-L106T wall mounting configuration
Chapter 1 General Information 11
2
System Setup
Sections include:
•
•
•
•
•
•
•
•
•
•
General
Removing Rear Panel
Installing Options
Installing I/O Equipment
Installing Software to the HDD
Exploded Diagram
PCM-9679 and I/O Adapter
Replacement
Power Supply and Cooling Fan
Replacement
Chapter 2 System Setup 13
Chapter 2 System Setup
2.1 General
The PPC-L106T consists of a PC-based industrial computer that is
housed in a protective cover. Your HDD, DDR RAM and power supply
and are all readily accessible by removing the rear panel. Any mainte-
nance or hardware upgrades can be carried out easily after removing the
rear panel.
Warning! Do not remove the rear cover until you have
verified that no power is flowing within the PPC-
L106T. Power must be switched off, and the
power cord must be disconnected. Every time
you service the PPC-L106T, you should be
aware of this.
2.2 Preparing For First Time Use
Before you set up the PPC-L106T system, you should have at least the
following items ready:
•
•
•
Power cord (in the accessory box)
PS/2 keyboard
PS/2 mouse (for system software installation, i.e. MS Windows,
NT, etc.)
14 PPC-L106T User Manual
2.3 Installing Options
2.3.1 Removing Rear Panel
Unscrew the eleven screws that secure the rear cover, then remove the
cover.
Figure 2.1: Removing the rear panel
Chapter 2 System Setup 15
2.3.2 Installing a primary 2.5" HDD (internal)
You can attach one enhanced Integrated Device Electronics (IDE) hard
disk drive to the PPC-L106T's internal controller which uses a PCI local-
bus interface. The advanced IDE controller supports faster data transfer
rates and allows the IDE hard drive to exceed 528 MB. The following are
instructions for installation:
1.
2.
Detach the rear panel and remove.
Place the HDD in the appropriate location inside the PPC-L106T,
and tighten the screws.
3.
Connect the cable included in this package (1x44-pin to 1x44-pin)
from the HDD to the PC board (CN9). Make sure that the red/blue
wire corresponds to pin 1 on the connector, which is labeled on the
board. Plug the other end of the cable into the enhanced IDE hard
drive, with pin 1 on the cable corresponding to pin 1 on the hard
drive.
Warnings! (1) Plug the other end of the cable into the
HDD, with pin 1 on the cable corresponding to
pin 1 on the hard drive. Improper connection
will damage the HDD.
(2) Be careful not to damage the CPU board
with your tools!
Figure 2.2: Installing a primary 2.5" HDD (internal)
16 PPC-L106T User Manual
2.4 Installing I/O Equipment
2.4.1 PS/2 keyboard and PS/2 mouse
The PPC-L106T provides a PS/2 keyboard connector that supports a PS/2
style keyboard and a 5-pin DIN keyboard extension cable. In most cases,
especially in embedded applications, a keyboard is not used. The standard
PC/AT BIOS will report an error or failure during power-on self-test
(POST) after a reset if the keyboard is not present. The BIOS standard
setup menu allows you to select* "All, But Keyboard" under the "Halt
On" selection. This allows no-keyboard operation in embedded system
applications without the system halting under POST. Note that the mouse
port on the PPC-L106T is a PS/2 mouse port.
Note:
“All but keyboard” is the default setting.
2.4.2 Mic-in, line-out
The PPC is equipped with a high quality audio interface, which provides
16-bit CD quality recording and playback as well as OPL3 compatible
FM music. It is supported by all major operating systems and is com-
pletely compatible with Sound Blaster Pro.
The audio interface includes two jacks: microphone-in and line-out (See
Fig. 1-2).
2.4.3 External VGA
The PPC-L106T can be connected to an external CRT monitor. To con-
nect an external CRT monitor, connect the monitor's VGA cable to the
PPC-102's VGA port and connect the monitor's power cable to an AC
outlet. The PPC-L106T's external CRT display (VGA) connector is a
standard 15-pin D-SUB connector commonly used for VGA.
2.4.4 Four serial COM ports
Many available peripherals, such as a serial mouse or an optional touch-
screen, require connection to a serial port. When an optional touchscreen
is ordered with a PPC-L106T, it shares COM4, and COM4 is not avail-
able as a serial port.
Chapter 2 System Setup 17
2.4.5 Ethernet
The PPC-L106T is equipped with a high performance 32-bit Ethernet
chipset which is fully compliant with the IEEE 802.3 100 Mbps CSMA/
CD standards. It is supported by major network operating systems. It is
also both 100Base-T and 10Base-T compatible. The medium type can be
configured via the RSET8139.EXE program included on the utility disk.
The Ethernet port provides a standard RJ-45 jack. The network boot fea-
ture can be utilized by incorporating the boot ROM image files for the
appropriate network operating system. The boot ROM BIOS files are
combined with system BIOS, which can be enabled/disabled in the BIOS
setup.
2.4.6 USB ports
The external USB device may be connected to the system though the 4-
pin USB ports located on the rear side of the system unit.
The USB ports support hot plug-in connection. You should install the
device driver before you use the device.
2.5 Installing Software to the HDD
Installing software requires an installed HDD. Software can be loaded in
the PPC-L106T using any of four methods:
2.5.1 Method 1: Use the Ethernet
You can use the Ethernet port to download software to the HDD.
2.5.2 Method 2: Use a USB Disk or USB CD-ROM
You can use a USB disk or USB CD-ROM to download the software to
your HDD.
2.5.3 Method 3: Use the COM or parallel port
Connect another PC to the PPC-L106T with an appropriate cable and
transmit the software to the PPC-L106T.
18 PPC-L106T User Manual
2.6 Exploded Diagram
Figure 2-3 shows all the components and parts that make up the PPC-
L106T. Use it as a guide when assembling and disasesembling your sys-
tem.
Figure 2.3: PPC-L106T exploded diagram
Chapter 2 System Setup 19
2.7 PCM-9679 and I/O Adapter Replacement
To replace or service the PCM-9679 (all-in-one CPU board) and I/O
adapter, complete the following steps:
1.
2.
3.
Turn off the power to the PPC-L106T
Remove the rear protective cover (see Figure 2-1)
Install the PCM-9679 in the panel and screw in the eight screws
(see Figure 2-4)
4.
5.
When the PCM-9679 is mounted in the panel, plug and press the
adapter into the socket (see Figure 2-4))
Some screws on the left connect the I/O adapter to the PC, and also
connect the adapter to the PCM-9679. Screw the screws into the
panel..
Note:
You may change the jumper settings for RS-
232/422/485 before installing the PCM-9679
and I/O adapter
20 PPC-L106T User Manual
Figure 2.4: Installing/removing the PCM-9679 & I/O adapter
Chapter 2 System Setup 21
3
The Engine of the
PPC-L106T (PCM-9679)
Sections include:
•
•
•
•
•
•
Introduction
Features
Jumpers and Connectors
CMOS clear
Watchdog timer configuration
COM2 RS-232/422/485setting
Chapter 3 System Setup 23
Chapter 3 The Engine of the PPC-L106T
(PCM-9679)
3.1 Introduction
The PCM-9679 is a highly reliable single board computer based on the
AMD LX800 CPU. It offers built-in functionality comparable to a com-
plete industrial PC system, including a VGA/LCD controller, network
communications, CompactFlash disk in a small 8" x 5.75" form factor.
For maximum performance, the PPC-L106T also supports a DDR
SODIMM socket that can accept up to 1024 MB memory. On-board fea-
tures include an Ethernet interface, audio interface, socket for Compact-
Flash card, Enhanced IDE interface that supports the Ultra DMA
protocol, one parallel port, four serial ports (RS-232 and RS-232/422/
485) with DB-9 connectors, and a mini-DIN PS/2 keyboard/mouse inter-
face. An SVGA/LCD display controller (for LCD and CRT displays)
allows LCD screen resolutions up to 800 x 600 @ 256 K colors.
The PCM-9679 complies with the "Green Function" standard and sup-
ports three types of power saving features: Normal, Doze and Sleep
modes.
The display type configuration is done through software. A single Flash
chip holds the system BIOS and the VGA BIOS. This minimizes the
number of chips and eases configuration. You can change the display
BIOS simply by programming the Flash chip.
Flash memory also offers faster data access and longer MTBF than
mechanical disk drives and is an ideal solution for critical commercial or
industrial applications. The watchdog timer ensures the system will be
reset if it stops due to a program bug or EMI problem.
24 PPC-L106T User Manual
3.2 Features
• Ultra-compact size single board computer as small as a 3 1/2" hard
disk drive (145 mm x 102 mm)
• On-board AMD LX800 CPU
• Up to 1024 MB system memory via an SODIMM (DDR)
• On-board VGA/LCD controller
• On-board 10/100Base-T Ethernet interface (dual LAN Optional)
• Supports on-board CompactFlash™ socket
• Built-in Enhanced IDE (AT bus) hard disk drive interface
• Four serial ports: three RS-232, one RS-232/422/485 or infared select-
able
• Supports One Mini PCI socket
• Supports 4 USB 2.0 (2 external, 2 internal)
• Supports 8 bit GPIO
Chapter 3 System Setup 25
3.3 Jumpers and Connectors
3.3.1 Setting jumpers
You can configure your panel PC to match the needs of your application
by setting jumpers. A jumper is the simplest kind of electrical switch. It
consists of two metal pins and a small metal clip (often protected by a
plastic cover) that slides over the pins to connect them. To “close” a
jumper, you connect the pins with the clip. To “open” a jumper you
remove the clip. Sometimes a jumper will have three pins, labeled 1, 2,
and 3. In this case, you would connect either pins 1 and 2 or pins 2 and 3.
The jumper settings are schematically depicted in this manual as follows:
open
closed
closed 2-3
A pair of needle-nose pliers may be helpful when working with jumpers.
open
closed
closed 2-3
If you have any doubts about the best hardware configuration for your
application, contact your local distributor or sales representative before
you make any changes.
26 PPC-L106T User Manual
3.3.2 Jumpers
The table below lists the function of each of the board’s jumpers.
Table 3.1: Jumpers and their functions
S1
Reset Button
J2
SMBUS Power Setting
CMOS Clear
J3
J4
AT/ATX Setting
J6
COM2 RS232/422/485 Setting
COM3/4 Pin9 output type setting
Battery Connector
J7
BT1
SLOT1
PCI/ISA bus expansion connector
3.3.3 Connectors
The table below lists the function of each of the board's connectors.
Table 3.2: Panel PC connectors
Label
J1
Function
Inverter power connector
Flat panel display connector
Primary IDE hard drive connector
Keyboard connector
J2
J3
J4
J5
Internal touchscreen connector
SODIMM socket
CN1
CN2
CN3
CN4
CN5
CN6
CN7
CN8
CN10
CN20
PS1
JS2
CompactFlash Disk secondary IDE connector
CD IN
I/O board connector
I/O board connector
Power FAN power connector
External KBT2
CPU FAN power connector
Power Switch
Speaker and Microphone connector (Reserved)
Power test connector (Reserved)
Brightness VR (Reserved)
Chapter 3 System Setup 27
TOUCH-(COM4)
SMBUS
CN3
H1
H3
H2
J2
J2
SMB_PWRSEL
INVERTER
U12
1
2
3
4
5
6
7
8
9
1011121314151617
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
U
GPIO
CN7
CN6
CN9 IDE
H4
INTERNAL USB
J3
J4
J3
Clear CMOS
CN11
CN13
IAS-5V/
PWR_LED
H5
-12VINPUT
Reset Button
BT1
H6
CN12
J4
AT/ATX Sel
CN14 MIO-(USB+COM3)
SLOT1
S1
SLOT1
CN16
INTERNAL
AUDIO OUT
CN17
J7
INTERNAL LAN
J6
CN19
CN18
INTERNAL
SPAKER
H9
H8
BT1
J6
J7
Figure 3.1: Jumpers on the PPC-L106T motherboard
CN3
CN2
CN1 CN5
TOUCH-(COM4)
SMBUS
CN3
H1
H3
H2
J2
SMB_PWRSEL
INVERTER
CN4
U12
1
2
3
4
5
6
7
8
9
1011121314151617
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
U
GPIO
CN7
CN6
CN7
CN8
CN6
CN9 IDE
H4
CN9
INTERNAL USB
J3
Clear CMOS
CN11
CN11
CN13
CN12
CN13
IAS-5V/
PWR_LED
H5
-12VINPUT
Reset Button
BT1
H6
CN12
J4
AT/ATX Sel
CN14 MIO-(USB+COM3)
SLOT1
CN16
INTERNAL
AUDIO OUT
CN17
J7
INTERNAL LAN
J6
CN17
CN19
CN18
INTERNAL
SPAKER
H9
H8
CN19
CN18
CN21
CN20
Figure 3.2: Connectors on the PPC-L106T motherboard
28 PPC-L106T User Manual
3.4 CMOS Clear for External RTC (J3)
Warning! To avoid damaging the computer, always turn off
the power supply before setting “Clear CMOS”.
Set the jumper back to “Normal operation” before
turning on the power supply.
This jumper is used to erase CMOS data and reset system BIOS informa-
tion.
The procedure for clearing CMOS is:
1.
2.
3.
4.
Turn off system.
Short pin 2 and pin 3.
Return jumper to pins 1 and 2.
Turn on the system. The BIOS is now reset to its default setting.
Table 3.3: CMOS clear (J3)
*Normal operation
Clear CMOS
* default setting
3.5 COM Port Interface (J6, J7)
The panel PC provides four serial ports (COM1, 3, 4: RS-232; COM2:
RS-232/422/485) in one COM port connector.
3.5.1 COM2 RS-232/422/485 setting (J6)
COM2 can be configured to operate in RS-232, RS-422, or RS-485 mode.
This is done via J6.
Chapter 3 System Setup 29
Table 3.4: COM2 RS-232/422/485 setting (J6)
*RS-232
RS-422
RS-485
* default setting
The IRQ and the address ranges for COM1, 2, 3, and 4 are fixed. How-
ever, if you wish to disable the port or change these parameters later you
can do this in the system BIOS setup. The table overleaf shows the
default settings for the panel PC’s serial ports.
COM1 and COM2 are one set. You can exchange the address range and
interrupt IRQ of COM1 for the address range and interrupt IRQ of
COM2. After exchanging, COM1's address range is 3F8 ~ 3FF and its
request IRQ is IRQ4: and COM2's address range is 2F8 ~ 2FF and its
interrupt IRQ is IRQ3.
COM3 and COM4 are another set. Their address and IRQ is the same as
the COM1/COM2 set
30 PPC-L106T User Manual
Table 3.5: Serial port default settings
Port
Address Range
Interrupt
COM1
COM2
COM3
COM4
3F8 ~ 3FF
2F8 ~ 2FF
3E8 ~ 3EF
2E8 ~ 2EF
IRQ4
IRQ3
IRQ10
IRQ5
3.5.2 COM3/COM4 pin 9 output setting (J7)
Table 3.6: COM3/4 pin 9 settings (J7)
*Normal operation +5 V output
+12 V output
*default setting
Chapter 3 System Setup 31
A
I/O Pin Assignments
Sections include:
Appendix A I/O Pin Assignments 41
Chapter A I/O Pin Assignments
A.1 Keyboard connector (CN5-1)
Table A.1: Keyboard connector
Pin
1
Signal
KB_DT
N/A
2
3
GND
+5 V
4
5
KB_CK
N/A
6
A.2 Mouse connector (CN5-2)
Table A.2: Mouse connector
Pin
1
Signal
MS_DT
N/A
2
3
GND
4
+5 V
5
MS_CK
N/A
6
42 PPC-L106T User Manual
A.3 VGA connector (CN6)
Table A.3: VGA connector
Pin
1
Signal
RED
6
2
GREEN
BLUE
N/A
1
2
3
4
5
11
12
13
14
15
3
4
5
GND
GND
GND
GND
N/A
6
7
10
8
9
10
11
12
13
14
15
GND
N/A
N/A
HSYNC
VSYNC
N/A
A.4 COM1 RS-232 serial port (CN1-2)
Table A.4: COM1 RS-232 serial port
Pin
1
Signal
DCD
RxD
TxD
DTR
GND
DSR
RTS
CTS
RI
1
2
3
4
5
6
2
7
8
9
3
4
5
6
7
8
9
Appendix A I/O Pin Assignments 43
A.5 COM3 RS-232 serial port connector (CN2-1)
Table A.5: COM3 RS-232 serial port
Pin
1
Signal
DCD
RxD
TxD
DTR
GND
DSR
RTS
CTS
RI
1
2
3
4
5
6
7
8
9
2
3
4
5
6
7
8
9
A.6 COM4 RS-232 serial port connector (CN2-2)
Table A.6: COM4 RS-232 serial port
Pin
1
Signal
DCD
RxD
TxD
DTR
GND
DSR
RTS
CTS
RI
2
3
4
5
6
7
8
9
44 PPC-L106T User Manual
A.7 COM2 Connector
Table A.7: COM2
Pin
1
RS-232
DCD
RX
RS-422
TX-
TX+
RX+
RX-
GND
---
RS-485
DATA-
DATA+
---
2
3
TX
4
DTR
GND
DSR
RTS
CTS
RI
---
5
---
6
---
7
---
---
8
---
---
9
---
---
Appendix A I/O Pin Assignments 45
A.8 Parallel port connector (CN1-1)
Table A.8: Parallel port connector
Pin
1
Signal
STROBE*
D0
1
2
14
2
15
16
17
18
19
20
21
22
23
24
25
3
D1
3
4
4
D2
5
5
D3
6
7
6
D4
8
7
D5
9
10
11
12
13
8
D6
9
D7
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
ACK*
BUSY
PE
SLCT
AUTOFD*
ERR*
INIT*
SLCTINI*
GND
GND
GND
GND
GND
GND
GND
GND
* active low
46 PPC-L106T User Manual
A.9 GPIO Connector (Default: No Load)
Table A.9: CN7 GPIO
Pin
1
Signal
+V5
Pin
2
Signal
GPIO4
GPIO5
GPIO6
GPIO7
GND
3
GPIO0
GPIO1
GPIO2
GPIO3
4
5
6
7
8
9
10
A.10 USB 3 / USB 4 Connector (Internal)
Table A.10: CN12 Internal USB 3 / USB 4
Pin
1
Signal
Pin
2
Signal
+V5_USB1
USB2_Z_P+
USB2_Z_P-
GND
+V5_USB1
USB3_Z_P+
USB3_Z_P-
GND
3
4
5
6
7
8
9
GND
Appendix A I/O Pin Assignments 47
A.11 SMBUS Connector (Default :No Load)
1
2
3
4
Table A.11: CN5 SMBUS Input
Pin
1
Signal
+V_SMB
GND
2
3
SMB_A_CLK
SMB_A_DAT
4
48 PPC-L106T User Manual
|
