NetLink e340/i640 Wireless Telephone
Mitel Networks 3300 ICP with
Mitel Networks 5220 IP Phone emulation
Setup and Administration
Part Number: 72-1084-02
Issue B
SpectraLink Corporation
Setup and Administration—NetLink e340/i640 Wireless Telephone
Mitel Networks 3300 ICP and 5220 IP Phone emulation
Table of Contents
1. ABOUT THIS DOCUMENT
1.1 Contacting SpectraLink
1.2 Icons and Conventions
4
4
4
2. SPECTRALINK E340/I640 WIRELESS TELEPHONE OVERVIEW
2.1 Quick Start Guide
5
6
7
8
2.2 System Diagram
2.3 System Components
3. THE NETLINK E340/I640 WIRELESS TELEPHONE
3.1 Specifications
10
10
11
3.2 The Display
4. NETLINK E340/I640 WIRELESS TELEPHONE CONFIGURATION
4.1 The Admin Menu
12
12
20
4.2 User-defined Preferences
5. LICENSE MANAGEMENT
5.1 Requirements
22
22
22
5.2 Configuration Process
6. MITEL NETWORKS VOIP INTEGRATION FACTORS
24
7. FEATURE PROGRAMMING
7.1 Feature Assignment
7.2 Feature Access
26
27
28
8. TESTING A WIRELESS TELEPHONE
30
9. CERTIFYING THE NETLINK E340/I640 WIRELESS TELEPHONES
9.1 Site Certification
31
31
31
33
9.2 Site Survey Mode
9.3 Solving Coverage Issues
10. SOFTWARE MAINTENANCE
34
10.1 Upgrading Wireless Telephones
34
11. TROUBLESHOOTING WIRELESS TELEPHONE PROBLEMS
11.1 Access Point Problems
36
36
36
37
11.2 Configuration Problems
11.3 Wireless Telephone Status Messages
PN: 72-1084-02-B.doc
Page 3
SpectraLink Corporation
Setup and Administration—NetLink e340/i640 Wireless Telephone
Mitel Networks 3300 ICP and 5220 IP Phone emulation
1. About This Document
This document explains how to configure and maintain the SpectraLink e340/i640
Wireless Telephone within the Mitel Networks 3300 Integrated Communications
Platform (ICP).
1.1 Contacting SpectraLink
SpectraLink wants you to have a successful installation. If you have questions please
contact our Customer Support Hotline at (800) 775-5330. The Hotline is open Monday
through Friday, 6:00 AM to 6:00 PM Mountain Time.
1.2 Icons and Conventions
This manual uses the following icons and conventions.
Caution! Follow these instructions carefully to avoid danger.
Note these instructions carefully.
ꢀ
This typeface indicates a key, label, or button on SpectraLink hardware.
NORM
PN: 72-1084-02-B.doc
Page 4
SpectraLink Corporation
Setup and Administration—NetLink e340/i640 Wireless Telephone
Mitel Networks 3300 ICP and 5220 IP Phone emulation
2. SpectraLink e340/i640 Wireless
Telephone Overview
The SpectraLink e340/i640 Wireless Telephone is a mobile handset for workplace IP
telephone systems. The Wireless Telephone operates over an 802.11b wireless Ethernet
LAN providing users a wireless voice over IP (VoIP) extension. By seamlessly
integrating with the Nortel IP telephony system, Wireless Telephone users are provided
with high-quality mobile voice communications throughout the workplace. The Wireless
Telephone gives users the freedom to roam throughout the workplace while providing all
the features and functionality of an IP desk phone.
The NetLink e340/i640 Wireless Telephone provides a wireless extension to the Mitel
Networks 3300 ICP VoIP solutions. The Wireless Telephone supports the MiNET
protocol, a proprietary protocol developed by Mitel Networks for communication
between a Mitel Networks IP phone and a Mitel Networks PBX.
The Wireless Telephones reside on the wireless LAN with other wireless devices using
Direct Sequence Spread Spectrum (DSSS) radio technology. The handset radio transmits
and receives packets at up to 11Mb/s. The SpectraLink e340/i640 Wireless Telephone
supports Wired Equivalent Privacy (WEP) as defined by the 802.11b specification.
SpectraLink offers the product with both 40-bit and 128-bit encryption. WEP increases
the security of the wireless LAN to a level similar to a wired Ethernet LAN.
IP multicast addresses are used by the SpectraLink i640 Wireless
Telephone system. This requires that multicasting be enabled on the
subnet used for the NetLink Wireless Telephones, SVP Server, and
Telephony Gateways.
ꢀ
Routers are typically configured with filters to prevent multicast traffic
from flowing outside of specific domains. The wireless LAN can be
placed on a separate VLAN or subnet to reduce the effects of broadcast
and multicast traffic from devices in other network segments.
PN: 72-1084-02-B.doc
Page 5
SpectraLink Corporation
Setup and Administration—NetLink e340/i640 Wireless Telephone
Mitel Networks 3300 ICP and 5220 IP Phone emulation
2.1 Quick Start Guide
1. A wireless LAN must be properly configured and operational through the use of
802.11b wireless access points (APs) listed on the NetLink Wireless Telephone
Access Point Compatibility matrix.
2. A TFTP Server must be available on the network in order to load the appropriate
software into the Wireless Telephones. See the License Management section for
detailed instructions for loading software on Wireless Telephones.
3. The supported Mitel Networks VoIP solution must be connected to your network
and completely operational.
4. The NetLink SVP Server, which facilitates the QoS on the wireless LAN for the
Wireless Telephones, must be on the same subnet as the Wireless Telephones and
have the proper versions of software.
NetLink SVP Server software.
Ensure you have the following versions:
173 svp100.toc
174
zvmlinux
175 flashfs
5. Configure your Wireless Telephone to ensure that it is associated with the
Wireless LAN, has the appropriate software, and has the correct IP Address for
the supported Mitel Networks IP telephony system. See the License Management
section for detailed instructions for loading software onto Wireless Telephones.
PN: 72-1084-02-B.doc
Page 6
SpectraLink Corporation
Setup and Administration—NetLink e340/i640 Wireless Telephone
Mitel Networks 3300 ICP and 5220 IP Phone emulation
2.2 System Diagram
The following diagram shows the SpectraLink components residing on a network with
the Mitel Networks IP telephony system, access points (APs), and wireless LAN Ethernet
Switched Hub:
Access Point
TFTP Server
SVP Server
Ethernet switch
Wireless
Telephones
Access Point
Mitel IP system
optional
Wireless
POS
PSTN
or
PBX
Mitel IP
Phones
Wireless
Telephones
Ethernet cable
Phone cable
Device supplied by
SpectraLink
(Mitel Networks IP telephony server architecture example)
PN: 72-1084-02-B.doc
Page 7
SpectraLink Corporation
Setup and Administration—NetLink e340/i640 Wireless Telephone
Mitel Networks 3300 ICP and 5220 IP Phone emulation
2.3 System Components
•
NetLink e340 Wireless Telephone – The NetLink e340 Wireless Telephone is a
lightweight, durable handset specifically designed for mobile workplace use within a
facility using the supported Mitel Networks IP telephony system and 802.11b APs in
a wireless LAN.
•
NetLink i640 Wireless Telephone – The NetLink i640 Wireless Telephone offers a
durable design with push-to-talk functionality.
Wireless Telephone functionality is provided by emulating the Mitel Networks 5220
Internet Telephone. Among other features, the Wireless Telephone can receive calls
directly, receive transferred calls, transfer calls to other extensions, and make outside
and long distance calls (subject to the restrictions applied in your facility.) The
Wireless Telephones are to be used on-premises; they are not cellular or satellite
phones.
NetLink e340/i640 Wireless Telephones use Direct Sequence Spread Spectrum radio
technology (DSSS) to transmit audio packets over wireless LAN APs that support
SpectraLink Voice Priority (SVP).
•
NetLink SVP Server – SpectraLink Voice Priority (SVP) is the SpectraLink quality
of service (QoS) mechanism that is implemented in the Wireless Telephone and AP
to enhance voice quality over the wireless network. SVP gives preference to voice
packets over data packets on the wireless medium, increasing the probability that all
voice packets are transmitted efficiently and with minimum or no delay. SVP is fully
compatible with the IEEE 802.11b standards.
The NetLink SVP Server is an Ethernet LAN appliance that works with the AP to
provide QoS on the wireless LAN. All MiNET packets to and from the SpectraLink
e340/i640 Wireless Telephones pass through the NetLink SVP Server and are
encapsulated for prioritization as they are routed to and from the supported Mitel
Networks VoIP solution or other Wireless Telephone.
SVP is required for QoS because the current IEEE 802.11b wireless LAN standard
provides no mechanism for differentiating audio packets from data packets. This
standard is undergoing revision to version 802.11e to provide all the functionality of
SVP in an industry standard, thus ensuring high-quality voice in a mixed client
environment. Once 802.11e is ratified, SpectraLink and its 802.11b technology
partners will adopt the new specification.
•
•
Mitel Networks IP System - Mitel Networks 3300 ICP VoIP solution.
Access Points – supplied by third party vendors, access points provide the
connection between the wired Ethernet LAN and the wireless (802.11b) LAN. Access
points must be positioned in all areas where Wireless Telephones will be used. The
number and placement of access points will affect the coverage area and capacity of
the wireless system. Typically, the requirements for use of SpectraLink e340/i640
Wireless Telephones are similar to that of wireless data devices.
PN: 72-1084-02-B.doc
Page 8
SpectraLink Corporation
Setup and Administration—NetLink e340/i640 Wireless Telephone
Mitel Networks 3300 ICP and 5220 IP Phone emulation
Access points must utilize SpectraLink Voice Priority (SVP). Contact SpectraLink, or
a certified SpectraLink distributor, for information about APs that support SVP.
•
Ethernet Switch – interconnects multiple network devices, including the NetLink
SVP Server, the supported Mitel Networks IP telephony system, Mitel Networks IP
Phones and the access points. Ethernet switches provide the highest performance
networks, which can handle combined voice and data traffic, and are required when
using the NetLink e340/i640 Wireless Telephones.
Although a single Ethernet switch network is recommended, the Wireless Telephones
and the NetLink SVP Server can operate in larger, more complex networks, including
networks with multiple Ethernet switches, routers, VLANs, and/or multiple subnets,
as long as the SVP Server and access points are on the same subnet. However, in such
networks, it is possible for the quality of service (QoS) features of the NetLink SVP
Server to be compromised, and voice quality may suffer. Any network that consists of
more than a single Ethernet switch should be thoroughly tested to ensure any quality
issues are detected.
Note that the SpectraLink e340/i640 Wireless Telephones cannot “roam” from one
subnet to another. If routers and multiple subnets are in use, the Wireless Telephones
must only use access points attached to a single subnet, or be powered off and back
on to switch to a different subnet.
•
•
Mitel Networks IP Phone – The wired LAN desksets provided by Mitel Networks
for use with the supported Mitel Networks IP telephony system.
TFTP Server – Required in the system to distribute software to the Wireless
Telephones. May be on a different subnet than the supported Mitel Networks IP
telephony device(s) and APs.
PN: 72-1084-02-B.doc
Page 9
SpectraLink Corporation
Setup and Administration—NetLink e340/i640 Wireless Telephone
Mitel Networks 3300 ICP and 5220 IP Phone emulation
3. The NetLink e340/i640 Wireless
Telephone
NetLink e340 Wireless Telephone
NetLink i640 Wireless Telephone
3.1 Specifications
Radio frequency
Transmission type
Transmit data rate
Radio QoS
Wireless security
FCC certification
2.4000 – 2.4835 GHz
Direct Sequence Spread Spectrum (DSSS)
up to 11 Mb/s
SpectraLink Voice Priority (SVP)
Wired Equivalent Privacy (WEP), 40-bit and 128-bit
Part 15.247
Management
Voice encoding
VoIP Protocols
DHCP, TFTP
G.711, G.729a/ab
MiNET
Transmit power
Display
100 mW peak, < 10 mW average
Pixel-based (up to 4-line x 18-character) alphanumeric,
plus line and status indicators
e340 Dimensions
i640 Dimensions
e340 Weight
5.5” x 2.0” x 0.9” (14.0 x 5.1 x 2.3 cm)
5.9” x 2.2” x 1.0” (15.0 x 5.6 x 2.5 cm)
4.2 ounces (119.0 g)
i640 Weight
6.0 ounces (170.1 g)
Battery capacity
4 hours talk time, 80 hours standby
PN: 72-1084-02-B.doc
Page 10
SpectraLink Corporation
Setup and Administration—NetLink e340/i640 Wireless Telephone
Mitel Networks 3300 ICP and 5220 IP Phone emulation
3.2 The Display
Alphanumeric
Display information provided by the supported Mitel Networks VoIP solution when the
Wireless Telephone is off-hook will be passed directly to the Wireless Telephone display.
The Wireless Telephone will display up to 18 characters of each line. Certain characters
may be used by the supported Mitel Networks VoIP solution that are not implemented in
the Wireless Telephone such as definable and special characters.
Press the FCN key while off hook to scroll through features and emulated keys. Press the
LINE key while off hook to scroll through the line/memory keys.
Voicemail Icon
The Voicemail icon is controlled only by the OAI application.
Ringing and Tones
The ringing types are programmed by the Wireless Telephone user into the Wireless
Telephone and are not accessible or changeable by the supported Mitel Networks VoIP
solution. Whenever possible the audible and vibrating ringer on the Wireless Telephone
will follow the MiNET cadence commands provided by the supported Mitel Networks
VoIP solution.
Audio Features
Speakerphone features such as paging, hands-free mode and voice announce are not
available on the Wireless Telephone. The telephony switch should not be programmed to
support such features on the Wireless Telephone.
Line Indicators
The line indicators on the Wireless Telephone will convert to a solid or flashing number
to mimic the icons next to Line keys on the Mitel Networks 5220. The text that appears
next to the line keys on the 5220 IP Phone is accessed on the Wireless Telephone by
pressing the LINE key.
PN: 72-1084-02-B.doc
Page 11
SpectraLink Corporation
Setup and Administration—NetLink e340/i640 Wireless Telephone
Mitel Networks 3300 ICP and 5220 IP Phone emulation
4. NetLink e340/i640 Wireless Telephone
Configuration
The NetLink e340/i640 Wireless Telephones should be provisioned in the supported
Mitel Networks VoIP solution in the same manner as the Mitel Networks 5220 Internet
Telephones. Each Wireless Telephone may be configured for site-specific requirements
by opening the Admin menu and selecting options or entering specific information. Any
settings entered in the Admin menu must conform to system settings. Only the Wireless
Telephone being configured is affected by the Admin menu settings.
The Wireless Telephone user may select several usability options from the Standby
menu, described below in the User-defined Preferences section. This information is also
provided in the end user manual.
4.1 The Admin Menu
The Admin Menu contains configuration options that are stored locally (on each Wireless
Telephone). Every Wireless Telephone is independent and if the default settings are not
desired, the admin options must be set in each Wireless Telephone requiring different
settings.
Opening the Admin Menu
1. With the Wireless Telephone powered OFF, simultaneously press and hold the
Power On and Power Off keys.
2. Release the Power On key, then release the Power Off key. The Admin Menu
displays.
If an admin password has been set, the display will require its entry before
opening the Admin Menu. If no password is set, the display will proceed
directly into the Admin Menu.
ꢀ
Entering and editing Admin Menu options
An asterisk (*) next to an option indicates that it is selected. The default settings are
shown in the table below with an * prior to the option. Use the Up, Down, and Select
side buttons and the softkeys to navigate and select:
Up/Down buttons:
Select button:
OK softkey
Save softkey:
Bksp softkey:
Cncl softkey:
Up softkey:
display previous/next menu item.
selects the menu item or option.
selects the menu item or option.
saves the entry.
backspaces to allow editing of entry.
cancels edit and returns to previous menu level.
returns to previous menu level.
exits the menu (at the top level).
exits to standby state (from any level)
Exit softkey:
END CALL key:
PN: 72-1084-02-B.doc
Page 12
SpectraLink Corporation
Setup and Administration—NetLink e340/i640 Wireless Telephone
Mitel Networks 3300 ICP and 5220 IP Phone emulation
Alphanumeric String Entry
1. Press the first digit/letter. The digit displays. Press the key again to scroll through
the letters associated with that key.
Example: if you press 2 repeatedly, you will see 2, A, B, and C, a, b, and c.
The following table shows which key will allow you to enter non-numeric
characters or other characters not represented on the keypad.
To Enter
Press
. - _ ! # $ % & ‘ ( ) , : ; / \ = @ ~
1
0
7
9
Space
Q,q
Z,z
2. When the correct entry displays, press Right Arrow to move on to the next
character. Repeat for each digit/letter of the entry. To erase, press the Left Arrow
or Bksp softkey to erase the previous character.
3. Press the Save softkey to save the entry and return to the menu.
Press the Up softkey to abort and return to the menu without saving any changes.
PN: 72-1084-02-B.doc
Page 13
SpectraLink Corporation
Setup and Administration—NetLink e340/i640 Wireless Telephone
Mitel Networks 3300 ICP and 5220 IP Phone emulation
The following table lists the Admin Menu items. Detailed descriptions of each item
appear below the table.
Admin Menu Items
2nd Level
3rd Level
4th Level
IP Address
*Use DHCP
Static IP
Phone IP
TFTP Server IP
Default Gateway
Subnet Mask
SVP IP Addr
RTC IP Addr
OAI Server IP
ESS ID
Static Entry
*Learn Once
Learn Always
Set Current
License Management
Restore Defaults
Site Survey Mode
Regulatory Domain
Security
*None
WEP
Authentication
Open System
Shared Key
WEP On/Off
Key Information
Default Key
Key Length
Key 1-4
Rotation Secret
Cisco FSR
Username
Password
Clear PIN number
OAI on/off
Enable OAI
Disable OAI
Admin PW
PN: 72-1084-02-B.doc
Page 14
SpectraLink Corporation
Setup and Administration—NetLink e340/i640 Wireless Telephone
Mitel Networks 3300 ICP and 5220 IP Phone emulation
IP Address
There are two modes in which the Wireless Telephone can operate: DHCP enabled or
Static IP. Select the mode for operation from the IP Address menu:
* Use DHCP: will use Dynamic Host Configuration Protocol to assign an IP
Address each time the Wireless Telephone is turned on. If DHCP is enabled, the
Wireless Telephone also receives all other IP Address configurations from the
DHCP server.
Static IP: allows you to manually set a fixed IP Address. If selected, the Wireless
Telephone will prompt for the IP Addresses of each configurable network
component. When entering addresses, enter the digits only, including leading
zeroes. No periods are required.
Regardless of the mode in which the Wireless Telephone is operating, the following
components must be configured:
Phone IP – the IP Address of the Wireless Telephone. This is automatically assigned if
DHCP is used. If using Static IP configuration, you must obtain a unique IP Address for
each phone from your network administrator.
SVP Server IP – the IP Address of the NetLink SVP Server. If using Static IP
configuration, this is simply the IP Address of the NetLink SVP Server. Note that the
NetLink SVP Server must be statically configured to have a permanent IP Address. If
DHCP is being used, the Wireless Telephone will try the following, in order: the DHCP
option 151, then a DNS lookup of “SLNKSVP2” if the DHCP options 6 (DNS Server)
and 15 (Domain Name) are configured.
RTC IP Addr – the IP Address of the primary Mitel Networks device. If using Static IP
configuration, this is simply the IP Address of the device. If DHCP is being used, the
Wireless Telephone will try to obtain the device’s IP Address and port information using
the following DHCP options: 129.
The following components may be configured optionally:
TFTP Server IP – the IP Address of a TFTP server on your network which holds
software images for updating the Wireless Telephones. If this feature is configured (not
set to 0.0.0.0 or 255.255.255.255) either via Static IP configuration or using DHCP
option 66 (TFTP Server), or the Boot server/next server (siaddr) field, the Wireless
Telephone will check for newer software each time it is powered on or comes back into
range of your network. This check takes only a second and ensures that all Wireless
Telephones in your network are kept up-to-date with the same version of software.
OAI Server IP – the IP Address of the SpectraLink OAI Gateway (if applicable). If using
Static IP configuration, this is simply the IP Address of the SpectraLink OAI Gateway. If
DHCP is being used, the Wireless Telephone will try the DHCP option 152.
Default Gateway and Subnet Mask – used to identify subnets, when using a complex
network which includes routers. Both of these must be configured (not set to 0.0.0.0 or
255.255.255.255) for the Wireless Telephone to contact any network components on a
different subnet. They can be set using either Static IP configuration or via DHCP
options 3 (Default Gateway) and 1 (Subnet Mask) respectively. Contact your network
PN: 72-1084-02-B.doc
Page 15
SpectraLink Corporation
Setup and Administration—NetLink e340/i640 Wireless Telephone
Mitel Networks 3300 ICP and 5220 IP Phone emulation
administrator for the proper settings for your network. Note that the Wireless Telephones
cannot “roam” across subnets, since they cannot change their IP Address while
operational. Ensure that all your access points are attached to the same subnet for proper
operation. The Wireless Telephone can change subnets if DHCP is enabled, and the
Wireless Telephone is powered off then back on when within range of access points on
the new subnet.
ESSID
Select the option that will enable the Wireless Telephone to acquire APs with the correct
ESSID (Extended Service Set ID, aka SSID) each time it is turned on.
Note about Automatic Learn options: Broadcast ESSID must be enabled in the access
points for ESSID learning to function. Refer to the Configuration Note for your access
point or call your access point vendor for specifics. Overlapping wireless systems
complicate the use of ESSID learning as the Wireless Telephone in an overlapping area
could receive conflicting signals. If this is the situation at your site, use Static Entry or
Learn Once in an area without overlapping ESSIDs.
* Learn Once: allows the Wireless Telephone to scan all ESSIDs for a DHCP
server and/or TFTP server. Once either is found, the Wireless Telephone retains
the ESSID from whichever access point it associates with at that point. When
overlapping wireless systems exist, the Learn Once feature allows the Wireless
Telephone to use only the ESSID established at first learn at all subsequent power
ons. This ESSID is retained by the Wireless Telephone until the ESSID option is
reselected.
Learn Always: allows the Wireless Telephone to automatically learn the ESSID
at each power on or loss of contact with the wireless LAN (out of range). This
may be useful if the Wireless Telephone will be used at more than one site.
Static Entry: If your access points do not accept broadcast ESSID or if there are
overlapping wireless systems in use at the site, enter the correct ESSID manually.
License Management
License Management lets you select the VoIP protocol that your site is licensed to
download and run. The MiNET protocol to use for the NetLink e340/i640 Wireless
Telephones is 014. Any other protocol will cause the Wireless Telephone to malfunction.
After selecting the correct protocol for your site, you should upgrade the software for the
Wireless Telephones. See the Upgrading Wireless Telephones section for more
information.
Restore Defaults
The Restore Defaults option will set all user and administrative parameters to their
factory defaults.
Site Survey Mode
Site Survey Mode is used to check the signal strength from access points. When you
select Site Survey Mode, the Wireless Telephone will remain in this mode until it is
powered off. See the Certifying the NetLink e340/i640 Wireless Telephone section for
PN: 72-1084-02-B.doc
Page 16
SpectraLink Corporation
Setup and Administration—NetLink e340/i640 Wireless Telephone
Mitel Networks 3300 ICP and 5220 IP Phone emulation
more information on this mode.
Regulatory Domain
The Regulatory Domain will default to North America on the Wireless Telephone
display. FCC requirements dictate that the menu for changing the domain be available by
password, which in our case is the LINE key. To change the domain, press LINE and then
enter the digits that represent the site’s domain. Note that both digits must be entered.
01 - North America
02 - Europe (except Spain and France); Japan (channels 1-13)
04 - Spain
05 – France
Note: as of this writing, Spain and France are adopting the general European Regulatory
rules. Check with your wireless LAN administrator or supplier for which domain to enter
in these countries.
Security
*NONE disables any 802.11 encryption or security authentication mechanisms.
WEP (Wired Equivalent Privacy) is a wireless encryption protocol that encrypts data
frames on the wireless medium allowing for greater security in the wireless network. If
WEP/Encryption is required at this site, you must configure each Wireless Telephone to
correspond with the encryption protocol set up in the access points. Select the entries
from the options below to enable the Wireless Telephone to acquire the system.
Set each of these options to match exactly the settings in your APs.
ꢀ
Encryption codes display as they are entered. For security reasons codes
will not display when a user returns to the Admin menu, Encryption
options.
ꢀ
Note that WEP may be set to “optional” at the AP if there are wireless
devices in use that do not have WEP capability. All wireless devices must
be upgraded to WEP capability for a fully secured WEP environment.
ꢀ
Authentication
Select either Open System or Shared Key.
WEP On/Off
Select either WEP Off or WEP On.
Key Information
Press the Right Arrow key to scroll through the options:
Default Key: Enter the key # specified for use by the WTs. This will be 1
through 4.
Key Length: Select either 40-bit or 128-bit depending on the key length
specified for use at this location.
Key 1-4: Scroll to the key option that corresponds to the Default Key that
was entered above. Enter the encryption key as a sequence of hexadecimal
PN: 72-1084-02-B.doc
Page 17
SpectraLink Corporation
Setup and Administration—NetLink e340/i640 Wireless Telephone
Mitel Networks 3300 ICP and 5220 IP Phone emulation
characters. (Use the 2 and 3 keys to access hexadecimal digits A-F, use the
Right Arrow key to advance to the next digit, and the Left Arrow key to
backspace.) For 40-bit keys you will need to enter 10 digits, for 128-bit
keys you will need to enter 26 digits. The display will scroll as needed.
Rotation Secret: This is used for proprietary WEP key rotation. Refer to your
custom document if this feature is supported in your system.
Cisco FSR (Fast Secure Roaming) In order to provide the highest level of security
without compromising voice quality on Cisco Aironet wireless LAN access points,
SpectraLink and Cisco Systems have cooperated to implement the Fast Secure Roaming
mechanism. FSR is designed to minimize call interruptions for Wireless Telephone users
as they roam throughout a facility. Existing Aironet 350, 1100, and 1200 APs may
require a firmware upgrade to support FSR. Cisco FSR requires advanced configuration
of the Cisco access points in your site. See your Cisco representative for detailed
documentation on configuring your access points and other required security services on
your wired network. To configure Cisco FSR in your Wireless Telephone, you must
enter a Radius Server username and password into each phone.
Username: Enter a username that matches an entry on your Radius server.
Usernames are alphanumeric strings, and can be entered using the alphanumeric
string entry technique.
Password: Enter the password that corresponds to this Username.
OAI On/Off
SpectraLink’s Open Application Interface (OAI) enables third-party computer
applications to display alphanumeric messages on the Wireless Telephone display and
take input from the Wireless Telephone keypad. Refer to the Open Application Interface
(OAI) Specification (Version 1.2) documentation for information about administering the
OAI Gateway and the services it can provide.
If you have an OAI Gateway installed in your system, OAI may be optionally enabled in
each Wireless Telephone. You may select whether the Wireless Telephone should
attempt to connect to the SpectraLink OAI Gateway by choosing either the Enable or
Disable options in this menu.
If OAI is enabled, and an OAI IP Address is available to the telephone (either via DHCP
or Static IP configuration), the telephone will communicate with the OAI Server at power
on, and periodically while it is powered on. If you don’t have a SpectraLink OAI
Gateway installed at your site, you should disable the OAI feature to preserve network
bandwidth and battery life.
Admin PW
The Admin PW (password) controls access to the administration functions in the Admin
Menu. The password must be set in each Wireless Telephone for which controlled access
is desired. Wireless Telephones are shipped without any Admin Menu password.
If you exit with no entry, the password is erased and the display will not
require it before displaying the Admin Menu.
ꢀ
PN: 72-1084-02-B.doc
Page 18
SpectraLink Corporation
Setup and Administration—NetLink e340/i640 Wireless Telephone
Mitel Networks 3300 ICP and 5220 IP Phone emulation
4.2 User-defined Preferences
The following user-defined preferences are also covered in the NetLink e340/i640
Wireless Telephone user guide. The system administrator can refer to this list for more
information about customizing Wireless Telephone settings.
To configure the following options, the Wireless Telephone must acquire the system (no
error message may display) and be at the extension display. This is the standby state.
While in the standby state, press and hold FCN briefly to open the user options menu.
Use the following keys to display and select options:
Up/Down buttons:
Select button:
OK softkey
Save softkey:
Bksp softkey:
Cncl softkey:
Up softkey:
display previous/next menu item.
selects the menu item or option.
selects the menu item or option.
saves the entry.
backspaces to allow editing of entry.
cancels edit and returns to previous menu level.
returns to previous menu level.
exits the menu (at the top level).
exits to standby state (from any level)
Exit softkey:
END CALL key:
Standby menu item
2nd Level
3rd Level
Ring Type
Telephone ring
Normal Ring
Vibrate Ring
Vib/Norm Ring
Auxiliary ring 1
Auxiliary ring 2
“
“
Noise Mode
Normal
High
Severe
Alias IP Addr
Current IP Addr
Extension
Mitel options
Current RTC IP
Current TCP Port
Current RTP Port
Push-to-talk
Channel
1-8
Enable/Disable
Enable
Disable
Ring Type: Select Ring Type then Telephone Ring to change the standard ring used for
normal operation. From the Telephone Ring menu, select either Normal Ring (an
audible alert), Vibrate Ring or Vib/Norm Ring (vibrate for five seconds and then audible
alert for subsequent rings). The Auxiliary Ring modes are reserved for future use. The
ring type currently in use displays with an asterisk (*).
PN: 72-1084-02-B.doc
Page 19
SpectraLink Corporation
Setup and Administration—NetLink e340/i640 Wireless Telephone
Mitel Networks 3300 ICP and 5220 IP Phone emulation
Noise Mode: provides options that describe the noise level in your environment.
Selecting the correct option will adjust the Wireless Telephone to account for background
noise. Select Normal: for most office environments; High: for moderate background
noise; or Severe: for extremely noisy conditions. Use of the non-Normal modes is not
recommended unless you are in a loud environment or you may find it difficult to be
heard on your Wireless Telephone.
Alias IP Addr: displays the IP address currently assigned to this Wireless Telephone by
the SVP Server.
Current IP Addr: displays the IP address currently assigned to the Wireless Telephone.
The IP address is not set here, it is merely displayed and may not be changed.
Extension: allows you to enter the user extension for this Wireless Telephone. This
number is for display purposes only, entering it does not assign the extension in the host
telephone system.
Mitel options: displays the ports being utilized for receiving data at the Wireless
Telephone.
Push-to-talk: displays the menu for the two way radio feature in the NetLink i640
Wireless Telephone. The Channel option allows you to select a channel 1-8 to send and
receive radio messages. The Enable/Disable option allows you to enable or disable the
radio feature. See the NetLink i640 Wireless Telephone end user document for more
information about push-to-talk.
(Additional options may be present. Contact your system administrator for information.)
PN: 72-1084-02-B.doc
Page 20
SpectraLink Corporation
Setup and Administration—NetLink e340/i640 Wireless Telephone
Mitel Networks 3300 ICP and 5220 IP Phone emulation
5. License Management
The NetLink e340/i640 Wireless Telephone system supports a number of different IP
protocol integrations. All NetLink e340/i640 series Wireless Telephones are shipped
from SpectraLink with a generic software load that allows them to associate to a wireless
LAN and download their functional software from a TFTP server. The Wireless
Telephones will not function properly without downloading appropriate software.
The following details the process to properly configure NetLink e340/i640 Wireless
Telephones and download software via over-the-air file transfer.
5.1 Requirements
• A wireless LAN must be properly configured and operational through the use of
802.11b wireless access points.
• The supported Mitel Networks IP telephony system must also be connected to
your network and completely operational.
• A TFTP Server must be available on the network in order to load the appropriate
software into the Wireless Telephones.
• Finally, ensure that the Battery Pack on the Wireless Telephone is fully charged.
5.2 Configuration Process
1. Download the latest NetLink e340/i640 Wireless Telephone IP software from
2. Load the latest version of the NetLink e340/i640 Wireless Telephone MiNET
code and place it on the TFTP Server and ensure the TFTP Server is started. The
three files that are needed must be named slnk_cfg.cfg, pd11usc.bin, and
phintl24.bin.
3. If statically assigning IP Addresses, ensure that the Phone IP Address, TFTP
Server IP, Subnet Mask, and Default Gateway information are accurate in the
Admin Menu. If using a DHCP Server, ensure that the DHCP options are set. See
the NetLink e340/i640 Wireless Telephone Configuration section for detailed
configuration instructions.
4. Ensure the Wireless Telephone has properly configured ESSID and Reg Domain
Information within the Admin Menu. If you are accepting broadcast ESSIDs at
your access points, the handset will automatically learn the ESSID information
when powering on. See the NetLink e340/i640 Wireless Telephone Configuration
section for detailed configuration instructions.
5. Using the Admin Menu on the Wireless Telephone, ensure the License
Management menu option is set to 014. This ensures the handset will check for
the proper MiNET files each time it powers on. See the NetLink e340/i640
Wireless Telephone Configuration section for detailed configuration instructions.
PN: 72-1084-02-B.doc
Page 21
SpectraLink Corporation
Setup and Administration—NetLink e340/i640 Wireless Telephone
Mitel Networks 3300 ICP and 5220 IP Phone emulation
6. Power cycle the Wireless Telephone.
7. The MiNET code will now download to the handset. The status bar will increment
fully across the display for each function that is being performed in the download
process. Upon completion of the update process, the handset will re-boot with the
new firmware.
8. If the Wireless Telephone is statically configured, you may now enter the SVP IP
address and RTC address as detailed in the NetLink e340/i640 Wireless Telephone
Configuration section above.
9. Register the Wireless Telephone with the supported Mitel Networks VoIP
solution as if it were a Mitel Networks 5220 IP Phone and properly label the
handset with the appropriate extension.
For future software upgrades, simply update the files that are stored on the
TFTP Server. Each time the Wireless Telephone is powered on, it will
check with the TFTP Server to ensure it has the proper software version.
ꢀ
PN: 72-1084-02-B.doc
Page 22
SpectraLink Corporation
Setup and Administration—NetLink e340/i640 Wireless Telephone
Mitel Networks 3300 ICP and 5220 IP Phone emulation
6. Mitel Networks VoIP Integration Factors
This section describes the mapping between the emulated Mitel Networks 5220 IP Phone
and the NetLink e340/i640 Wireless Telephone.
Voice Messaging Access
Voicemail access is obtained through the Message key which is assigned on the Wireless
Telephone to FCN + 3.
CODECs
The NetLink e340/i640 Wireless Telephone is compatible with the G.711 and G.729a/ab
CODECs. There is no setting required on the Wireless Telephone.
DHCP
Dynamic Host Configuration Protocol (DHCP) is a standardized protocol that enables
clients to be dynamically assigned with various configuration parameters, such as an IP
Address, subnet mask, default gateway, and other critical network configuration
information. DHCP servers centrally manage such configuration data, and are configured
by network administrators with settings that are appropriate for a given network
environment. The Wireless Telephone will search for Mitel Networks server
configuration in the vendor specific and site-specific options listed in the table below.
The Wireless Telephone will use the following DHCP options if DHCP use is enabled:
Option Meaning
1
3
6
Subnet Mask
Default Gateway
DNS Server
15 Domain Name
66 TFTP Server
151 NetLink SVP Server
152 SpectraLink OAI Gateway
128 Mitel TFTP Server address (not currently
used by Wireless Telephone)
129 Mitel PBX RTC IP address
130 String containing “MITEL IP PHONE”
siaddr Boot server or next server
TFTP
The Wireless Telephone uses TFTP to update the Wireless Telephone software over the
802.11b wireless LAN.
PN: 72-1084-02-B.doc
Page 23
SpectraLink Corporation
Setup and Administration—NetLink e340/i640 Wireless Telephone
Mitel Networks 3300 ICP and 5220 IP Phone emulation
DNS
Domain Name System (DNS), an industry-standard protocol, locates computers on an IP-
based network. IP networks rely on number-based addresses to move information on the
network. However, users are better at remembering friendly names than number-based
addresses, so, it is necessary to translate user-friendly names into addresses that the
network can recognize. The Wireless Telephone will use DNS to automatically translate
names into IP Addresses for these components: TFTP Server and the NetLink SVP
Server.
PN: 72-1084-02-B.doc
Page 24
SpectraLink Corporation
Setup and Administration—NetLink e340/i640 Wireless Telephone
Mitel Networks 3300 ICP and 5220 IP Phone emulation
7. Feature Programming
Softkey A
Softkey B
Softkey C
Fcn6
Fcn1
Fcn2
Fcn4
Fcn3
Softkey D
14
12
10
8
13
11
9
Programmable
Line or Feature
keys
7
5
6
4
3
2
Line1
The button mapping from the Mitel Networks 5220 IP Phone to the NetLink Wireless
Telephone is designed to preserve nearly all of the functionality of the 5220 IP Phone
within a small, mobile device. All telephone functions and messaging features are
supported if possible. Speakerphone functions are not supported.
The Wireless Telephone has four softkeys to the 5220’s three softkeys. The last or
rightmost softkey on the Wireless Telephone, known as Softkey D, emulates the Hold
key on the 5220. The other three softkeys emulate the functions of the three softkeys of
the 5220.
The Wireless Telephone uses “shortcut keys” to emulate the feature keys on the 5220.
Pressing LINE, FCN, or MENU plus a shortcut key will activate the assigned line
appearance or feature.
Feature key number 1 on the 5220 is the Line 1 key in the Wireless Telephone. All other
feature keys may be programmed to either line appearances or features. When the
Wireless Telephone becomes active, it requests a label for each of the feature keys from
the PBX which tells it whether the feature key is assigned to a feature or to a line
appearance. If the key is assigned to a line appearance, the Wireless Telephone lists the
line extension plus any shortcut key on the Line Appearance display, visible when the
LINE key is pressed. If the key is assigned to a feature, the Wireless Telephone lists it and
any shortcut key on the Feature display, visible when the FCN key is pressed. Each line
or feature appears in feature key order. Its shortcut key is determined by this order. OAI
programming will override any shortcut keys assigned by the Wireless Telephone.
PN: 72-1084-02-B.doc
Page 25
SpectraLink Corporation
Setup and Administration—NetLink e340/i640 Wireless Telephone
Mitel Networks 3300 ICP and 5220 IP Phone emulation
7.1 Feature Assignment
The table below shows how the keys of the 5220 IP Phone are mapped to key sequences
on the Wireless Telephone.
Wireless
Telephone
Shortcut & Key
Sequence
5220 key
Feature
Trans/Conf
Cancel
Transfer or conference
Cancel
FCN + 1
FCN + 2
FCN + 3
FCN + 4
FCN + 5
FCN + 6
Line + 1
Message
Redial
Voicemail
Redial
Mute/Unmute
Superkey
Superkey
Feature Key #1
Line appearance
Programmable Feature Key 2-14 If Feature, the feature name
FCN + 7
Programmable to either line
appearances or features.
appears on the Feature menu
with a shortcut key1 in the order
of assignment to a feature key.
8
9
*
0
#
If Line, the line extension
appears on the Line
Appearance list, with a line
number that corresponds to the
order of assignment to a
feature key.
Line + 2
3
4
5
6
7
8
9
Softkey1
Softkey2
Softkey3
Hold
Phonebook (Phbk)
Programmable
Programmable
Hold
Softkey A
Softkey B
Softkey C
Softkey D
If an Open Application Interface (OAI) is operational, a function key
sequence will be assigned in the OAI configuration and will override any
function sequence established in the PBX.
ꢀ
1
Note: There may be more features programmed than there are available shortcut keys. In this situation, the feature may be activated
by using the Up, Down, Select buttons on the side of the Wireless Telephone.
PN: 72-1084-02-B.doc
Page 26
SpectraLink Corporation
Setup and Administration—NetLink e340/i640 Wireless Telephone
Mitel Networks 3300 ICP and 5220 IP Phone emulation
7.2 Feature Access
In its standby state, the Wireless Telephone displays the extension assigned to this
Wireless Telephone. The active state is initiated by pressing either the Start Call key or
the MENU key. When the active state is initiated, the Wireless Telephone contacts the
PBX and displays the data provided – the time, date, default line icon, any voicemail
icon, and softkey and feature key labels. If the Start Call key has been pressed, the
Wireless Telephone is off-hook and there is a dial tone. If the MENU key is pressed, there
is no dial tone; pressing MENU again will bring up the Menu display.
While in the active state, you may switch to any display – Line, Feature, or Menu – by
pressing its corresponding key. Pressing a softkey will activate the feature displayed.
Line Appearances
While off hook, press the LINE key to view the shortcut keys and assigned extensions for
line appearances. There are nine possible line appearances which correspond to the nine
indicators at the top of the Wireless Telephone display. When a line is in use, the
indicator converts to the line number and a + will appear after the shortcut key on the list,
emulating a lit LED. Press the LINE key again to display the second page of the list if
more than four line keys have been programmed. To use an extension, press the
corresponding shortcut key. You may also use the Up, Down, and Select buttons to
scroll through the displays and activate the line appearances on this list. Press the End
Call key to exit the Line Appearance list.
PN: 72-1084-02-B.doc
Page 27
SpectraLink Corporation
Setup and Administration—NetLink e340/i640 Wireless Telephone
Mitel Networks 3300 ICP and 5220 IP Phone emulation
Menu Display:
The softkey labels on the Wireless Telephone are truncated to 4 characters. The complete
text for each softkey may be displayed by pressing the MENU key from the standby state.
The shortcut key assigned to the softkey feature and the complete text for each of the
softkeys displays.
Activate the softkey features while in the Menu display by pressing the softkey, pressing
the shortcut key, or using the Up, Down, and Select buttons to scroll through and
activate the features on this list. Press the End Call key to exit the Menu display.
Feature List
The 5220 IP Phone has several fixed feature keys. The SpectraLink implementation
supports five fixed features that are suitable to a mobile user through the Function (FCN)
key on the Wireless Telephone. When FCN is pressed, the display lists the first four fixed
features and the assigned shortcut key. Pressing FCN repeatedly will display the
remaining items on the list as programmed to the 5220 keys. These display in the order
programmed to the corresponding keys on the 5220, along with any shortcut key, as
available. A + will appear after the shortcut key, emulating a lit LED, indicating that the
corresponding feature is turned on. OAI options appear at the end of the list. All OAI
keys will preempt shortcuts assigned to other keys.
Activate the fixed features on the off-hook Wireless Telephone by pressing FCN + the
shortcut key. You may also use the Up, Down and Select buttons to scroll through and
activate the features on this list. Press the End Call key to exit the list.
1 Trans/Conf
2 Cancel
3 Message
4 Redial
5 Mute/Unmute
6 Superkey
7
First
screen
Second
screen
8
9
(feature)
(feature)
(feature)
Third
screen
Fourth
screen,
etc.2
* (OAI)
0 (OAI)
# (OAI)
2
Note: There may be more features programmed than there are available shortcut keys. In this situation, the feature may be activated
by using the Up, Down, Select buttons on the side of the Wireless Telephone.
PN: 72-1084-02-B.doc
Page 28
SpectraLink Corporation
Setup and Administration—NetLink e340/i640 Wireless Telephone
Mitel Networks 3300 ICP and 5220 IP Phone emulation
8. Testing a Wireless Telephone
Verify proper registration and operation of each Wireless Telephone by performing the
following tests on each Wireless Telephone in an active wireless area.
1. Power on the Wireless Telephone by pressing Power On. You will see a series of
messages displayed as the Wireless Telephone acquires the system. The Wireless
Telephone should display the user extension or dashes if no extension is
programmed. Any error messages should clear.
2. Press the Start Call key. The extension number should be replaced by information
from the supported Mitel Networks VoIP solution and you should hear dial tone.
Place a call and listen to the audio quality. End the call by pressing the End Call
key.
3. Place a call to the Wireless Telephone and verify ring, answer, clear transmit, and
clear receive audio.
4. Go off-hook and use the FCN key to verify the Features list.
5. Go off-hook and use the LINE key to verify the Line appearances / Line features
list.
6. Press the End Call key. Any line indicators should turn off and the extension
number display will return.
PN: 72-1084-02-B.doc
Page 29
SpectraLink Corporation
Setup and Administration—NetLink e340/i640 Wireless Telephone
Mitel Networks 3300 ICP and 5220 IP Phone emulation
9. Certifying the NetLink e340/i640 Wireless
Telephones
Conduct a preliminary Site Survey Mode test according to the directions given below.
Note any areas where coverage is conflicting or inadequate. Note any system difficulties
and work with your wireless LAN and/or LAN system administrator to determine the
cause and possible remedy. See the section Troubleshooting Wireless Telephone
Problems for clues to possible sources of difficulties.
9.1 Site Certification
The installer should not leave the site before performing installation verification.
These tests must be performed in typical operating conditions, especially if heavy loads
occur. Testing sequence and procedure is different for every installation. Generally, you
should organize the test according to area and volume, placing numerous calls to others
who can listen while you perform coverage tests. Note any areas with excessive static or
clarity problems and report it to Customer Service.
The coverage test will also require you to put the Wireless Telephone in Site Survey
Mode and walk the entire coverage area to verify all access points.
The installation is not complete until these certification steps have been
performed. Do not hand out Wireless Telephones at a site that has not been
certified.
9.2 Site Survey Mode
Test signal strength in the covered area by performing a Site Survey. Put a Wireless
Telephone in Site Survey Mode (see NetLink e340/i640 Wireless Telephone
Configuration section) and walk the entire coverage area while viewing the display.
The FCN key toggles between the three coverage modes described below. The Wireless
Telephone will remain in Site Survey mode until it is powered off. When testing is
complete, press Power Off to power off the Wireless Telephone.
Numbers racing across the Wireless Telephone display indicate AP information is being
obtained. A Waiting message indicates the system is not configured properly and the
Wireless Telephone cannot find any APs.
Detect dBm coverage
As you walk the perimeter, the two-line display will show the top four access points that
the Wireless Telephone can contact in a code as illustrated below.
XXX1 YY XXX2 YY
XXX3 YY XXX4 YY
-dBm
PN: 72-1084-02-B.doc
Page 30
SpectraLink Corporation
Setup and Administration—NetLink e340/i640 Wireless Telephone
Mitel Networks 3300 ICP and 5220 IP Phone emulation
• XXX1 through XXX4 are the last four digits of the access points’ MAC
address. The primary access point (the access point which had the strongest
signal to this Wireless Telephone) displays first, followed by the three access
points with the next strongest signals.
• YY is the power level in dBm at which this Wireless Telephone heard the
associated access point. Although shown as a positive number, YY represents
negative dBm and lower numbers represent stronger signals. For example, a
displayed value of 40 indicates -40dBm, and is therefore a stronger signal than
a display of 50 (which indicates -50dBm). At least one access point’s reading
should be stronger than -70 dBm in all areas.
Note any areas that have inadequate dBm readings.
Detect Overlap or Conflicts
Press FCN to toggle to the Site Survey function that shows the channel number of the
access points. Use this information to detect overlaps or conflicts in access point
signaling.
XXX1 ZZ XXX2 ZZ
XXX3 ZZ XXX4 ZZ
Chnl
• XXX1 through XXX4 are the last four digits of the access points’ MAC
address.
• ZZ is the channel number that the access point is using.
Note any areas that have access points that are in contention for the same channel.
It is preferable that no overlaps exist anywhere in your facility. If the site survey mode
indicates two APs using the same channel, then at least one other AP must be indicated at
10 dBm stronger than those APs to avoid channel conflicts.
Confirm Supported Data Rates
Press FCN to toggle to the Detail function. Use this information to confirm signal
strength and supported data rates.
#:
Full MAC
dB Ch 1b2b5b11b
Detl
• # is the number (1-4) of the AP
• Full MAC is the MAC address of the AP
• dB is the signal strength of the AP
• Ch is the channel of the AP
PN: 72-1084-02-B.doc
Page 31
SpectraLink Corporation
Setup and Administration—NetLink e340/i640 Wireless Telephone
Mitel Networks 3300 ICP and 5220 IP Phone emulation
• 1b2b5b11b is an example of the data rate that may be displayed
Walk around the site to determine supported data rates, one AP at a time. In any location
you may use the Right Arrow key to display the second best AP, arrow again to the third
best, and so on to the fourth best. The Left Arrow key steps you back to the first best.
Each data rate (1,2,5.5, or 11Mb/s) that is supported by the AP is shown. Those rates that
are in the Basic Rate set (sometimes referred to as “required” rates) are indicated by a ‘b’
following the rate number. The Supported and Basic data rate(s) should be the same on
all APs as is appropriate for your environment.
9.3 Solving Coverage Issues
Coverage issues are best resolved by adding and/or relocating access points.
Overlap issues may be resolved by reassigning channels to the access points or by
relocating the access points.
PN: 72-1084-02-B.doc
Page 32
SpectraLink Corporation
Setup and Administration—NetLink e340/i640 Wireless Telephone
Mitel Networks 3300 ICP and 5220 IP Phone emulation
10. Software Maintenance
The NetLink e340/i640 Wireless Telephones use proprietary software programs written
and maintained by SpectraLink Corporation. The software versions that are running on
the Wireless Telephones can be displayed during power on by holding down the Power
On key.
SpectraLink or its authorized dealer will provide information about software updates and
how to obtain the software (for example, downloading from a web site).
10.1 Upgrading Wireless Telephones
After software updates are obtained from SpectraLink, they must be transferred to the
appropriate location in the LAN to update the code used by the Wireless Telephones.
NetLink e340/i640 Wireless Telephones allow over-the-air transfer of software updates
from the designated TFTP server to the Wireless Telephones. The downloader function in
the Wireless Telephone checks its software version every time the Wireless Telephone is
powered on. If there is any discrepancy, the Wireless Telephone immediately begins to
download the update.
Normal Download Messages
When the Wireless Telephone is powered on, it displays a series of messages indicating
that it is searching for new software, checking the versions, and downloading. The
normal message progression is:
Message
Description
Checking Code
Wireless Telephone is contacting the TFTP Server to determine if it has a
newer version of software that should be downloaded.
Erasing Memory Wireless Telephone has determined that a download should occur and is
erasing the current software from memory. This message also displays a
progress bar. When the progress bar fills the display line the erase operation
is complete.
Updating Code
Wireless Telephone is downloading new software into memory. This message
also displays a progress bar. When the progress bar fills the display line the
update operation is complete on that file.
When the update is complete, the Wireless Telephone displays the extension number, and
is ready for use.
PN: 72-1084-02-B.doc
Page 33
SpectraLink Corporation
Setup and Administration—NetLink e340/i640 Wireless Telephone
Mitel Networks 3300 ICP and 5220 IP Phone emulation
Download Failure or Recovery Messages
The following display messages indicate a failure or recovery situation during the
download process.
Message
Description
Server Busy
Wireless Telephone is attempting to download from a TFTP Server that is
busy downloading other phones and refusing additional downloads. The
Wireless Telephone will automatically retry the download every few
seconds.
TFTP
ERROR(x):yy
A failure has occurred during the TFTP download of one of the files. (x) =
The file number which was being downloaded; yy is an error code
describing the particular failure. Possible error codes are:
01 = TFTP server did not find the requested file.
02 = Access violation (reported from TFTP server).
07 = TFTP server reported "No such user" error. Check the TFTP server
configuration.
81 = File put into memory did not CRC. The Wireless Telephone will
attempt to download the file again.
FF = Timeout error. TFTP server did not respond within a specified
period of time.
Erase Failed
Waiting
Download process failed to erase the memory in the Wireless Telephone.
This operation will retry.
Wireless Telephone has attempted some operation several times and
failed, and is now waiting for a period of time before attempting that
operation again.
PN: 72-1084-02-B.doc
Page 34
SpectraLink Corporation
Setup and Administration—NetLink e340/i640 Wireless Telephone
Mitel Networks 3300 ICP and 5220 IP Phone emulation
11. Troubleshooting Wireless Telephone
Problems
Wireless Telephones can exhibit transmission problems in several ways. They can cease
functioning properly, display error messages, or display incorrect data. When using and
troubleshooting Wireless Telephones, consider the following problem sources to
determine the best method of approaching any specific situation.
11.1 Access Point Problems
Most, but not all, Wireless Telephone audio problems have to do with access point range,
positioning and capacity. Performing a Site Survey as described in Section 9.2 can isolate
the AP causing these types of problems. If the Wireless Telephone itself is suspected,
conduct a parallel Site Survey with a Wireless Telephone that is known to be properly
functioning.
In range/Out of range – service will be disrupted if a user moves outside the area
covered by the wireless LAN access points. Service is restored if the user moves
back within range. If a call drops because a user moves out of range, the Wireless
Telephone will recover the call if the user moves back into range within a few
seconds.
Capacity – in areas of heavy use, the call capacity of a particular AP may be
filled. If this happens, the user will hear three chirps from the Wireless Telephone.
The user can wait until another user terminates a call, or move within range of
another AP and try the call again. If a user is on a call and moves into an area
where capacity is full, the system attempts to find another AP. Due to range
limitations, this may be the same as moving out of range.
Transmission Obstructions – prior to system installation, the best location for
APs for optimum transmission coverage was determined. However, small pockets
of obstruction may still be present, or obstructions may be introduced into the
facility after system installation. This loss of service can be restored by moving
out of the obstructed area, or by adding APs.
11.2 Configuration Problems
Certain problems are associated with improper configuration of either the supported
Mitel Networks VoIP solution or the Wireless Telephone.
Configuration problems are generally corrected by changing the configuration at the
supported Mitel Networks VoIP solution or on the Wireless Telephone. There may also
be incorrect programming of the AP. See the Configuration Note for the AP in use at the
site.
PN: 72-1084-02-B.doc
Page 35
SpectraLink Corporation
Setup and Administration—NetLink e340/i640 Wireless Telephone
Mitel Networks 3300 ICP and 5220 IP Phone emulation
11.3 Wireless Telephone Status Messages
Wireless Telephone status messages provide information about the NetLink e340/i640
Wireless Telephone's communication with the AP and host telephone system. The
following table summarizes the status messages, in alphabetical order.
Message
3 chirps
Description
Action
Wireless Telephone is not able to
communicate with the best AP,
probably because that AP has no
bandwidth available.
None. This is only a warning, the
call will handoff to the best AP
once it becomes available.
Bad Config
Bad ESSID
Some needed configuration
parameter has not been set.
Check all required Wireless
Telephone configuration
parameters for valid settings.
The Wireless Telephone is
configured for “static ESSID” (as
opposed to “Learn once” or “Learn
always” and no ESSID has been
entered.
Enter an ESSID in the
configuration settings or change to
one of the “Learn” modes.
(battery icon), Low
Battery and beep
Low battery
In call: the battery icon displays
and a soft beep will be heard when
the user is on the Wireless
Telephone and the battery charge
is low. User has 15–30 minutes of
battery life left.
Not in call: The battery icon
displays whenever the battery
charge is low The message Low
Battery and a beep indicate a
critically low battery charge when
user is not on the Wireless
Telephone. The Wireless
Telephone will not work until the
Battery Pack is charged.
Can’t Renew DHCP The functional code is not able to get Configuration problem. Check the
a lease renewal.
gateway address in the DHCP
server.
Charging …
The Wireless Telephone is charging
in the Desktop Charger.
No action needed.
Charge Complete
Checking Code
The Wireless Telephone is now fully
charged.
No action needed.
Wireless Telephone is contacting the None, this message should only
TFTP Server to determine if it has a
newer version of software that
should be downloaded.
last for approximately one second.
If message remains displayed,
power off and contact SpectraLink
customer support.
Checking DHCP IP
The Wireless Telephone is retrieving None. This is informational only.
DHCP information from the DHCP
server.
PN: 72-1084-02-B.doc
Page 36
SpectraLink Corporation
Setup and Administration—NetLink e340/i640 Wireless Telephone
Mitel Networks 3300 ICP and 5220 IP Phone emulation
Message
Description
Action
CRC Code Error
The software which has been TFTP
downloaded has a bad redundancy
code check.
Try the download again, it is
possible the software was
corrupted during download. If the
error repeats, check that the
download image on the TFTP
server is not corrupted.
Code Mismatch!
DHCP Error (1-4)
The software loaded into the
Wireless Telephone is incorrect for
this model phone.
Replace the software image on the
TFTP server with software that is
correct for the phone model.
DHCP Error 1
The Wireless Telephone cannot
locate a DHCP server. It will try
every 4 seconds until a server is
located.
DHCP Error 2
The Wireless Telephone has not
received a response from the
server for a request to an IP
Address. It will retry until a server
is found.
DHCP Error 3
DHCP Error 4
The server refuses to lease the
Wireless Telephone an IP
Address. It will keep trying.
The server offered the Wireless
Telephone a lease that is too short.
The minimum lease time is 10
minutes but SpectraLink engineers
recommend at least one hour
minimum lease time. The Wireless
Telephone will stop trying.
Reconfigure the server and power
cycle the Wireless Telephone.
DHCP Lease Exp
The Wireless Telephone’s DHCP
lease has expired, and the call (if
any) cannot continue.
The Wireless Telephone failed to
renew its DHCP lease, either
because the DHCP server is not
running, or because the
configuration has been changed by
the administrator. The Wireless
Telephone will attempt to negotiate
a new lease, which will either work,
or change to one of the above
DHCP errors (1-4).
DHCP NACK error
A NACK (Negative ACKnowledge)
The DHCP lease currently in use
was received from the DHCP server. by the Wireless Telephone is no
longer valid, which forces the
Wireless Telephone to restart. This
problem should resolve itself on
the restart. If it does not, the
problem is in the DHCP server.
PN: 72-1084-02-B.doc
Page 37
SpectraLink Corporation
Setup and Administration—NetLink e340/i640 Wireless Telephone
Mitel Networks 3300 ICP and 5220 IP Phone emulation
Message
Description
Action
DO NOT POWER
OFF
The Wireless Telephone is in a
critical section of the software
update.
None. Do not remove the battery
or attempt to power off the phone
while this is displayed. Doing so
may require the phone to be
returned to SpectraLink to be
recovered.
Duplicate IP
The Wireless Telephone has
detected another device with its
same IP Address.
If using DHCP, check that the
DHCP server is properly
configured to avoid duplicate
addresses.
If using Static IP, check that the
Wireless Telephone was assigned
a unique address.
Erase Failed
Download process failed to erase the Operation will retry but may
memory in the Wireless Telephone.
eventually report the error "int.
error: 0F" Power cycle the phone.
Erasing Memory
Wireless Telephone has determined
that a download should occur and is
erasing the current software from
memory.
None. When the progress bar fills
the display line the erase operation
is complete.
Initializing …
The Wireless Telephone is
None. This is informational only.
performing power on initialization.
Internal Err. # #
The Wireless Telephone has
detected a fault from which it cannot
recover.
Record the error code so it can be
reported.
Turn the Wireless Telephone off
then on again.
If error persists, try registering a
different Wireless Telephone to
this telephone port.
If error still persists, contact
SpectraLink Technical Support and
report the error.
Network Busy
No Host IP
All APs are full or busy.
Try call again later.
The Wireless Telephone is
Enter a valid IP Address in the
configured for “static IP” (as opposed configuration settings or change to
to “use DHCP”) and no valid host IP
Address (the Wireless Telephone’s
IP Address) has been entered.
“use DHCP”.
No IP Address
Invalid IP.
Check the IP Address of the
Wireless Telephone and re-
configure if required.
No PBX Response
The Wireless Telephone tried to
send a message to the supported
Mitel Networks VoIP solution and
failed to get a response.
Verify the supported Mitel
Networks VoIP solution is
operational and connected to the
network.
PN: 72-1084-02-B.doc
Page 38
SpectraLink Corporation
Setup and Administration—NetLink e340/i640 Wireless Telephone
Mitel Networks 3300 ICP and 5220 IP Phone emulation
Message
Description
The Wireless Telephone is
Action
No SVP IP
Enter a valid NetLink SVP server
configured for “static IP” (as opposed IP Address in the configuration
to “use DHCP”) and no valid NetLink setting or change to “use DHCP.”
SVP Server address has been
entered.
No SVP Response
The NetLink SVP Server is not
responding to requests from the
Wireless Telephone.
This may be caused by bad radio
reception or a problem with the
NetLink SVP Server. The Wireless
Telephone will keep trying to fix the
problem for 20 seconds, and the
message may clear by itself. If it
does not, the Wireless Telephone
will restart. Report this problem to
the system administrator if it keeps
happening.
No SVP Server
Wireless Telephone can’t locate SVP IP Address configuration of
Server.
NetLink SVP Server is wrong or
missing.
SVP Server is not working.
Check error status screen on
NetLink SVP Server.
No LAN connection at the SVP
Server
Verify NetLink SVP Server
connection to LAN.
No Net Access
No Net Found
Cannot authenticate / associate with
AP
Verify the AP configuration.
This indicates any of the following:
Verify that the AP is turned on.
•
•
No radio link
Verify the ESSID of the wireless
LAN and enter or Autolearn it
again if required.
No ESSID – Autolearn not
supported (or)
incorrect ESSID
Try getting closer to an AP. Check
to see if other Wireless
Telephones are working within the
same range of an AP. If so, check
the ESSID of this Wireless
Telephone.
•
•
Out of range
Verify that all the WEP settings in
the Wireless Telephone match
those in the APs.
Incorrect WEP settings
No Reg Domain
Not Installed!
Regulatory Domain not set.
Configure the Regulatory Domain
of the Wireless Telephone
A required software component is
missing.
Check that all required software
files are on the TFTP server, if
over-the-air downloading is being
used. If the error repeats, contact
SpectraLink Technical Support.
PN: 72-1084-02-B.doc
Page 39
SpectraLink Corporation
Setup and Administration—NetLink e340/i640 Wireless Telephone
Mitel Networks 3300 ICP and 5220 IP Phone emulation
Message
Description
Action
Press End Call
Your call has ended.
Press the Power Off / End Call key
to return to standby mode.
Restart Command
The Wireless Telephone received a
None. The Wireless Telephone
restart command from the supported will automatically restart in a few
Mitel Networks VoIP solution.
seconds.
Select License
Server Busy
The correct protocol has not been
selected from the license set.
Using the administrative menus,
select one license from the set to
allow the phone to download the
appropriate software.
Wireless Telephone is attempting to
None, the Wireless Telephone will
download from a TFTP Server that is automatically retry the download
busy downloading other devices and
refusing additional downloads.
every few seconds.
SVP Service Rej.
The NetLink SVP Server has
The Wireless Telephone will restart
rejected a request from the Wireless and attempt to re-register with the
Telephone.
SVP Server, which should fix the
problem. Report to your
administrator if it keeps happening.
System Locked
(with Busy Tone)
NetLink SVP Server is locked.
Try call again later, system has
been locked for maintenance.
System Busy
(with Busy Tone)
NetLink SVP Server is busy or out of All call paths are in use, try call
resources. again in a few minutes.
TFTP ERROR(x):yy A failure has occurred during a TFTP Error code 01, 02 or 07 - check the
software download. (x) = The file
number which was being
downloaded; yy is an error code
describing the particular failure.
Possible error codes are:
TFTP server configuration.
Error code 81, the Wireless
Telephone will attempt to
download the file again.
For other messages, power off the
Wireless Telephone, then turn it on
again to retry the download. If the
error repeats, note it and contact
SpectraLink Technical Support.
01 = TFTP server did not find the
requested file.
02 = Access violation (reported
from TFTP server).
07 = TFTP server reported "No
such user" error.
81 = File put into memory did not
CRC.
FF = Timeout error. TFTP server
did not respond within a specified
period of time.
Updating Code…
Updating …
Wireless Telephone is downloading
new software into memory.
None. When the progress bar fills
the display line the update
operation is complete on that file.
The Wireless Telephone is internally None. The Wireless Telephone
updating its software images.
may do this briefly after a
download. This is informational
only.
PN: 72-1084-02-B.doc
Page 40
SpectraLink Corporation
Setup and Administration—NetLink e340/i640 Wireless Telephone
Mitel Networks 3300 ICP and 5220 IP Phone emulation
Message
Description
Action
Waiting…
Wireless Telephone has attempted
some operation several times and
failed.
None. The Wireless Telephone is
waiting for a specified period of
time before attempting that
operation again.
Watchdog Timeout
The Wireless Telephone failed to
hear from the supported Mitel
Networks VoIP solution within the
watchdog timeout interval.
Verify the supported Mitel
Networks VoIP solution is
operational and connected to the
network.
PN: 72-1084-02-B.doc
Page 41
SpectraLink Corporation
Setup and Administration—NetLink e340/i640 Wireless Telephone
Mitel Networks 3300 ICP and 5220 IP Phone emulation
Index
Access point
Out of range, 35
Coverage, 32
Preferences, user-defined, 19
Push-to-talk, 20
Coverage test, 30
Overlap, 32
Regulatory Domain, 16
Restore Defaults, 16
Ring type, 19
Access point, description, 8
Automatic Learn, 15
Capacity, 35
Signal strength, 30
Channel number, 31
Checking code, 33
Coverage test, 30
Customer Support Hotline, 4
Data rates, 31
Site Certification, 30
Site Survey, 16, 30
Status messages, 36
Status messages, 39
Switched Hub, description, 9
Transmission obstructions, 35
Updating code, 33
Download messages
Failure or Recover, 34
Normal, 33
User Preferences, 19
Wireless Telephone
Erasing memory, 33
Extension, 20
Configuration problems, 35
Display IP address of, 20
Problems with, 35
High noise option, 19
Hotline, 4
OAI On/Off, 18
Obstructions, 35
OEM SVP Server, 8
Status messages, 36, 39
Wireless Telephone, description, 8
PN: 72-1084-02-B.doc
Page 42
|