Installation Instructions for SLO-SYN ®
MODEL SS2000MD4 Translator Drive
400030-043 Rev G
Danaher Motion Superior Electric
Safety
Safety symbols used in this manual are:
Warning Alerts users to potential physical danger or harm. Failure to follow
warning notices could result in personal injury or death.
Caution Directs attention to general precautions, which if not followed, could result
in personal injury and/or equipment damage.
Note Highlights information critical to your understanding or use of the product.
Instructions
Only qualified personnel should install or perform servicing procedures on this equipment. Do not
operate the unit without the enclosures in place as voltage present in this unit can cause serious or
fatal injury.
Before performing any work on the unit, allow at least five minutes for the capacitors to
discharge fully.
Voltage is present on unprotected pins when unit is operational.
The "PWR ON" LED must be off for approximately 30 seconds before making or breaking
the motor connections.
Motors powered by these drives may develop extremely high torque. Disconnect AC power to
these drive before doing any mechanical work.
This unit is designed for 115 VAC input only (see Section 4.2,
Electrical Specifications).
Warranty And Limitation Of Liability
Danaher Motion (the "Company") warrants to the first end user purchaser (the "purchaser") of
equipment manufactured by the Company that such equipment, if new, unused and in original
unopened cartons at the time of purchase, is free from defects in material and workmanship under
normal use and service for a period of one year from date of shipment from the Company's factory or
a warehouse of the Company in the event that the equipment is purchased from the Company or for a
period of one year from the date of shipment from the business establishment of an authorized
distributor of the Company in the event that the equipment is purchased from an authorized
distributor.
THE COMPANY'S OBLIGATION UNDER THIS WARRANTY SHALL BE STRICTLY AND
EXCLUSIVELY LIMITED TO REPAIRING OR REPLACING, AT THE FACTORY OR A SERVICE
CENTER OF THE COMPANY, ANY SUCH EQUIPMENT OR PARTS THEREOF WHICH AN
AUTHORIZED REPRESENTATIVE OF THE COMPANY FINDS TO BE DEFECTIVE IN MATERIAL
OR WORKMANSHIP UNDER NORMAL USE AND SERVICE WITHIN SUCH PERIOD OF ONE
YEAR. THE COMPANY RESERVES THE RIGHT TO SATISFY SUCH OBLIGATION IN FULL BY
REFUNDING THE FULL PURCHASE PRICE OF ANY SUCH DEFECTIVE EQUIPMENT. This
warranty does not apply to any equipment which has been tampered with or altered in any way,
improperly installed or has been subject to misuse, neglect or accident.
SS2000MD4
3
400030-043 Rev G
Danaher Motion Superior Electric
THE FOREGOING WARRANTY IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, and of any other obligations
or liabilities on the part of the Company; and no person is authorized to assume for the Company any
other liability with respect to equipment manufactured by the Company. The Company shall have no
liability with respect to equipment not of its manufacture. THE COMPANY SHALL HAVE NO
LIABILITY WHATSOEVER IN ANY EVENT FOR PAYMENT OF ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES, INCLUDING, WITHOUT LIMITATION, DAMAGES FOR INJURY
TO ANY PERSON OR PROPERTY.
Written authorization to return any equipment or parts thereof must be obtained from the Company.
The Company shall not be responsible for any transportation charges.
IF FOR ANY REASON ANY OF THE FOREGOING PROVISIONS SHALL BE INEFFECTIVE, THE
COMPANY'S LIABILITY FOR DAMAGES ARISING OUT OF ITS MANUFACTURE OR SALE OF
EQUIPMENT, OR USE THEREOF, WHETHER SUCH LIABILITY IS BASED ON WARRANTY,
CONTRACT, NEGLIGENCE, STRICT LIABILITY IN TORT OR OTHERWISE, SHALL NOT IN ANY
EVENT EXCEED THE FULL PURCHASE PRICE OF SUCH EQUIPMENT.
Any action against the Company based upon any liability or obligation arising hereunder or under any
law applicable to the sale of equipment, or the use thereof, must be commenced within one year after
the cause of such action arises.
The right to make engineering refinements on all products is reserved. Dimensions and other details
are subject to change.
SS2000MD4
4
400030-043 Rev G
Danaher Motion Superior Electric
Table of Contents
SECTION 1: INTRODUCTION.................................................................................... 6
1.1 USING THIS MANUAL.............................................................................................. 6
1.2 PRODUCT FEATURES............................................................................................... 6
SECTION 2: EXPRESS START UP ............................................................................ 7
SECTION 3: INSTALLATION GUIDELINES ........................................................... 8
3.1 MOUNTING............................................................................................................. 8
3.2 TERMINAL LOCATIONS AND ASSIGNMENTS........................................................... 9
3.3.1 MOTOR CONNECTIONS................................................................................... 10
3.3.2 POWER INPUT................................................................................................ 12
SECTION 4: SPECIFICATIONS................................................................................ 13
4.1 MECHANICAL....................................................................................................... 13
4.2 ELECTRICAL ........................................................................................................ 13
4.3 ENVIRONMENTAL................................................................................................. 13
4.4 MOTOR COMPATIBILITY ..................................................................................... 13
4.5 CURRENT SETTINGS............................................................................................. 15
4.6 STEP RESOLUTION ............................................................................................... 15
4.7 SIGNAL SPECIFICATIONS...................................................................................... 16
4.7.1 CONNECTOR PIN ASSIGNMENTS..................................................................... 16
4.7.2 SIGNAL DESCRIPTIONS .................................................................................. 16
4.7.3 LEVEL REQUIREMENTS.................................................................................. 16
4.7.4 TIMING REQUIREMENTS ................................................................................ 17
4.8 INDICATOR LIGHTS.............................................................................................. 17
SECTION 5: TORQUE VERSUS SPEED CHARACTERISTICS........................... 18
5.1 MOTOR PERFORMANCE....................................................................................... 18
5.2 TYPICAL TORQUE VERSUS SPEED CURVES ......................................................... 19
SECTION 6: SYSTEM CHECKING ......................................................................... 35
APPENDIX A: TROUBLESHOOTING ........................................................................ 36
A.1 ELECTRICAL INTERFERENCE PROBLEMS ........................................................... 36
A.2 CUSTOMER SUPPORT .......................................................................................... 36
SS2000MD4
5
400030-043 Rev G
Danaher Motion Superior Electric
SECTION 1: INTRODUCTION
1.1 USING THIS MANUAL
It is important that you understand how this SLO-SYN® 2000MD4 Translator/Drive is
installed and operated before you attempt to use it. Read this manual completely before
proceeding with the installation of this unit.
This manual is an installation and operating guide to the SLO-SYN 2000MD4
Translator/Drive. Section 1 gives an overview of the Drive and its features. Section 2
describes the steps necessary to place the drive into operation. General wiring guidelines
as well as the physical mounting of the unit and connections to the drive portion are
covered in Section 3.
Complete specifications, listed in Section 4, provide electrical, mechanical and
performance specifications. The procedure for setting the motor current level is also
covered in this section.
Torque versus speed characteristics with all appropriate SLO-SYN Stepper Motors are
given in Section 5. Section 6, System Checking, gives procedures to follow if the SLO-
SYN 2000 drive fails to operate properly.
Appendix A provides procedures for troubleshooting electrical interference problems.
1.2 PRODUCT FEATURES
SLO-SYN 2000MD4 Translator/Drive is a bipolar, adjustable speed, two-phase PWM
drive that uses hybrid power devices. It can be set to operate a step motor in full steps or
half steps. The maximum running speed is 3,000 rpm. To reduce the chances of electrical
noise problems, the control signals are optically isolated from the drive circuit. Features
include:
Switch selectable current levels of 0.5 through 3.5 amperes
Full short circuit protection (phase-to-phase and phase-to-ground)
Undervoltage and transient overvoltage protection
Efficient thermal design
Optically isolated inputs
Windings Off capability
Switch selectable step resolution
Compact size
Sturdy all-aluminum mounting base
SS2000MD4
6
400030-043 Rev G
Danaher Motion Superior Electric
SECTION 2: EXPRESS START UP
The following instructions define the minimum steps necessary to make your Drive
operational.
Always disconnect the AC power to the unit and be certain the "PWR
ON" LED is OFF before connecting or disconnecting the motor leads.
FAILURE TO DO THIS RESULTS IN A SHOCK HAZARD.
Always operate the Motor and the Drive GROUNDED. Be sure to twist
together the wires for each motor phase. Six twists per foot is a good
guideline.
1. Check to see that the motor used is compatible with the drive. Refer to Section 4.4 for a
list of compatible motors.
2. Set the correct current level for the motor being used per the instructions in Section 4.5.
Heat sinking may be required to maintain case temperature below +70° C (+158° F).
3. Select the appropriate step resolution and set the front panel switches as described in Sec-
tion 4.6.
4. Wire the motor per the "Motor Connections" description in Section 3.2.
5. Connect the power source to the DC input terminal strip. Be sure to follow the
instructions for connecting the filter capacitor as described in Section 3.2, under Power
Input.
If the motor operates erratically, refer to Section 5, "Torque Versus Speed
Characteristics". Clockwise and counter-clockwise directions are properly
oriented when viewing the motor from the end opposite the mounting
flange.
SS2000MD4
7
400030-043 Rev G
Danaher Motion Superior Electric
Section 3: Installation Guidelines
3.1 MOUNTING
The SLO-SYN Drive is mounted by fastening its mounting brackets to a flat surface as shown in
Figure 3.1. If the drive assembly is mounted against a bulkhead, be sure to apply a thin coating of
thermal compound between the drive and the mounting surface before fastening the unit in place.
Do not use too much thermal compound. It is better to use too little than too much.
Figure 3.1 Mounting Diagram
Case temperature should not exceed +70° C (+158° F). Forced air
cooling may be required to maintain temperature within the stated
limits.
When selecting a mounting location, it is important to leave at least two inches (51mm)
of space around the top, bottom and sides of the unit to allow proper airflow for cooling.
It is also important to keep the drive away from obvious noise sources. If possible, locate
the drive in its own metal enclosure to shield it and its wiring from electrical noise
sources. If this cannot be done, keep the drive at least three feet from any noise sources.
SS2000MD4
8
400030-043 Rev G
Danaher Motion Superior Electric
3.2 TERMINAL LOCATIONS AND ASSIGNMENTS
Figure 3.2 shows the terminal locations for the SLO-SYN SS2000MD4
Translator/Drive.
I/O Connector (J2)
Motor And Power Supply Connector (J1)
Figure 3.2, Terminal Locations
SS2000MD4
9
400030-043 Rev G
Danaher Motion Superior Electric
3.3.1 Motor Connections
All motor connections are made via the 6-terminal strip (J1). Terminal assignments are
given below. Motor connections are shown in Figure 3.3.
J1 Pin Assignment
1
2
3
4
M1 (Phase A+)
M3 (Phase A-)
M4 (Phase B+)
M5 (Phase B-)
Motor phase A is M1 and M3 and motor phase B is M4 and M5. The
motor frame must be grounded.
Cabling from the drive to the motor should be done with a shielded, twisted pair cable.
As a guideline, the wires for each motor phase should be twisted about six times per foot.
Danaher Motion offers the following motor cable configurations. These cables have
unterminated leads on both ends.
Length
Part Number
10 ft (3 m)
25 ft (7.6 m)
216022-031
216022-032
50 ft (15.2 m) 216022-033
75 ft (22.8 m) 216022-034
Figure 3.3 shows the possible motor wiring configurations.
SS2000MD4
10
400030-043 Rev G
Danaher Motion Superior Electric
MOTOR
MOTOR TERMINAL "M" NUMBERS
MOTOR
CONNECTOR PIN
CONNECTOR PIN
WHITE/
BLACK
1
5
DRIVE PIN 1
DRIVE PIN 4
RED
B
D
WHITE/
RED
DRIVE PIN 2
DRIVE PIN 1
DRIVE PIN 3
DRIVE PIN 4
H
F
BLACK
GREEN
3
4
4-LEAD MOTORS
1
5
RED
B
D
GREEN
WHITE
* N.C.
2
BLACK
G
H
E
F
N.C.*
6
WHITE/
RED
WHITE/
GREEN
DRIVE PIN 2
DRIVE PIN 1
DRIVE PIN 3
DRIVE PIN 4
3
4
6-LEAD MOTORS
1
5
GREEN
RED
B
D
E
ORANGE
BLACK
G
6
2
7
8
*
*
WHITE/
BLACK
WHITE/
GREEN
WHITE
A
H
C
F
WHITE/
RED
DRIVE PIN 2
DRIVE PIN 3
DRIVE PIN 4
3
4
8-LEAD MOTORS, SERIES CONNECTIONS
1
5
DRIVE PIN 1
B
D
E
RED
GREEN
BLACK
G
ORANGE
6
2
7
8
WHITE/
BLACK
WHITE/
GREEN
WHITE
WHITE/
RED
A
H
C
F
DRIVE PIN 2
DRIVE PIN 3
3
4
8-LEAD MOTORS, PARALLEL CONNECTIONS
*These leads must be insulated and isolated from other leads or ground.
Circled letters identify terminals for connector motors, numbers identify those for terminal box motors.
Figure 3.3 Motor Wiring Configurations
SS2000MD4
11
400030-043 Rev G
Danaher Motion Superior Electric
3.3.2 Power Input
The DC input power is connected to terminals 5 and 6 of the terminal strip (J1). Terminal
5 [Vm(+)] is the power supply plus (+) connection and pin 6 [Vom(-)] is the power
supply minus (-) connection.
An unregulated supply similar to that shown in Figure 3.4 is preferable. If a
regulated supply is used, it must be capable of operating with the added filter
capacitor. A switching regulated supply may not be suitable for use with this drive.
It is important that the capacitor (C1) be connected within three feet (0.9 meter) of
the input terminals. The capacitor must be of the correct value and have the proper
current and voltage parameters (see list of components).
It is recommended that the power supply leads be twisted together (6 twists per foot).
If the power supply is grounded, it must only be grounded on the
negative side or the short circuit protection will not operate properly.
T1
F1
J2 Drive
BR1
R1
AC +
5
6
Vm (+)
Vm (-)
C1
24 VAC
AC -
The cable between the filter capacitor (C1) and the drive should be
twisted (six twists per foot). Maximum wire length is three feet.
Use #16 AWG or larger wire.
Figure 3.4 Typical Power Supply For A Single Drive Application
Components
1.5 ampere time delay, 250 volt
5 ohm surge limiter, Phillips 2322-654-6158 or equivalent
130 VA, 24 VAC output
F1
R1
T1
BR1 General Instrument GBPC3502 or equivalent
C1
4700 µf, 5.5 ampere 20 kHz, 63 V rated, United Chemcon
53D472F063HS6 or equivalent
SS2000MD4
12
400030-043 Rev G
Danaher Motion Superior Electric
SECTION 4: SPECIFICATIONS
4.1 MECHANICAL
Size
(Inches) 1.56 H x 4.13 W x 3.25 D
(mm)
40 H x 105 W x 83 D
Weight
0.6 pounds (272 grams)
4.2 ELECTRICAL
DC Input Range............ 24 VDC min., 40 VDC max.
DC Current ................... see Motor Table
Drive Power Dissipation
(Worse Case)..... 35 watts
4.3 ENVIRONMENTAL
Temperature
Operating
+32° F to +122° F
(0° C to +50° C) free air ambient, Natural Convection. Maximum
heat sink temperature of 158° F (70° C) must be maintained.
Forced-air cooling may be required.
-40° F to +167° F
Storage
(-40° C to +75° C)
Humidity
Altitude
95% max. non-condensing
10,000 feet (3048 m) max.
4.4 MOTOR COMPATIBILITY
Motor Types
Superior Electric KM and M Series
M Frame Sizes M061 (NEMA 23D) through M092 (NEMA 34)
KM Frame Sizes KML061 (NEMA 23) through KML093 (NEMA 34)
M061 — M092
D6: KML060 — KML093
M061 — MH112
Do Not use larger frame size motor than those listed, or the drive may
be damaged.
Number of
Connections
4, 6, 8
Minimum Inductance
0.5 millihenrys
Maximum Resistance 0.25 x VDC Supply/I Setting
Maximum resistance is total of motor plus cable.
Example:
VDC = 30
I Setting = 3.5
R max. = 0.25 x 30/3.5 = 2.1 ohms
SS2000MD4
13
400030-043 Rev G
Danaher Motion Superior Electric
MOTORS FOR USE WITH THE SS2000MD4 TRANSLATOR/DRIVE
Current
Setting
(Amperes)
Power Supply Current
Standstill Maximum
(Amps. DC) (Amps. DC)
Motor
Winding Connection
M061
08
08
09
09
09
09
09
09
09
09
-
Series
2.5
3.5
3.0
3.5
3.0
3.5
3.0
3.5
3.0
3.5
2.5
2.5
3.5
3.0
3.5
3.0
3.5
3.0
3.5
3.0
3.5
3.5
1.0
1.0
1.0
1.0
1.5
1.0
1.0
1.0
1.5
1.0
1.0
1.2
1.0
1.0
1.0
1.5
1.0
1.0
1.0
1.5
1.0
1.8
2.0
2.0
2.5
3.5
2.0
3.5
1.5
3.0
2.0
3.0
1.5
1.5
3.0
2.5
4.0
2.0
4.0
2.0
4.0
2.5
4.0
2.5
M061
Parallel
M062
Series
M062
Parallel
M063
Series
M063
Parallel
M091
Series
M091
Parallel
M092
Series
M092
Parallel
KML060FO5
KML061FO5
KML061F11
KML062F07
KML062F13
KML063F07
KML063F13
KML091F07
KML091F13
KML092F07
KML092F13
KML093F07
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Power supply currents shown are measured at the output of the rectifier bridge in Figure
3.4.
M061, M062 and M063 motors listed include LS, LE, CS, FC and FD versions. M091
and M092 motors include FC and FD versions with 6 or 8 leads. Motors with windings
other than those listed can be used as long as the current ratings listed on the motors are
not exceeded.
All KML motors listed have 4 leads.
SS2000MD4
14
400030-043 Rev G
Danaher Motion Superior Electric
4.5 CURRENT SETTINGS
The proper current setting for each motor is shown on the individual torque vs. speed
curves. Use this current level to obtain the torque shown. Switches 1 through 7 select the
current level. Select the desired operating current by setting the appropriate switch to
position 1 (ON). The OFF position is labeled "0". Only one switch should be ON. If two
or more switches are ON, the one that selects the highest current level is the active
switch. The switch settings are:
Current
Position (amperes)
None
0.5
0.75
1.0
1.5
2.0
2.5
3.0
3.5
1
2
3
4
5
6
7
4.6 STEP RESOLUTION
The number of pulses per revolution is selected using position 8 of the switch described
in Section 4.5. The following chart shows the correct switch setting for each available
step resolution.
Switch
Position 8
Step
Resolution
Pulses Per
Revolution
0 (off)
1 (on)
Full-Step
Half-Step
200
400
MOTOR CURRENT &
STEP RESOLUTION
SWITCHES
J2
J1
Figure 4.1 Switches For Setting Current Level and Step Resolution
SS2000MD4
15
400030-043 Rev G
Danaher Motion Superior Electric
4.7 SIGNAL SPECIFICATIONS
4.7.1 Connector Pin Assignments
All connections are made via the 4-pin terminal strip (J2).
Pin Assignment
1
2
3
4
OPTO
PULSE
DIR
AWO
4.7.2 Signal Descriptions
OPTO Opto-Isolator Supply
User supplied power for the opto-isolators.
PULSE Pulse Input
A low to high transition on this pin advances the motor one step. The step size is
determined by the Step Resolution switch setting.
Direction Input
DIR
When this signal is high, motor rotation is clockwise. Motor rotation is counter-clockwise
when this signal is low.
Clockwise and counter-clockwise directions are properly oriented when viewing the
motor from the end opposite the mounting flange.
AWO
All Windings Off Input
When this signal is low, AC and DC current to the motor will be zero. There is no
holding torque when the AWO signal is low.
If you are using the drive with an MX2000, SS2000I or SS2000I-V
control, the READY input and the OPTO input on the control must be
jumpered together.
4.7.3 Level Requirements
OPTO
Voltage ....................4.5 to 6.0 VDC
Current.....................16 mA per signal used
Other Signals
Voltage
Low................... 0.8 VDC
0.0 VDC
High.................. OPTO
OPTO - 1 volt
Current
Low................... 16 mA
High.................. 0.2 mA
SS2000MD4
16
400030-043 Rev G
Danaher Motion Superior Electric
4.7.4 Timing Requirements
PULSE
Max. Frequency.......20 kHz
Max. Rise and
Fall Times................1 microsecond
Min. Pulse
Width .......................25 microseconds
Other Signals
Response Time ....... 25 microseconds
OPTO IN
12 VDC, 16 mA PER SIGNAL
CONTROL SIGNAL
560 ohms
PULSE
1/4 watt
DRIVE
CONTROL LOGIC COMMON
OPTO IN
4.5 - 6.0 VDC, 16 mA PER SIGNAL
CONTROL SIGNAL
PULSE
DRIVE
CONTROL LOGIC COMMON
OPTO IN
PULSE
4.5 - 6.0 VDC, 16 mA PER SIGNAL
DRIVE
TTL
CONTROL SIGNAL
7406
OPTO IN
5V
PULSE
DRIVE
SWITCH
OPTO 5V GND
Figure 4.2 Suggested Methods For Control Interface
4.8 INDICATOR LIGHTS
"FAULT" LED, Red
Lights to indicate over current condition. This condition is caused by motor wiring errors or a
ground fault.
Recovery from over current condition requires removing and then reapplying the power.
SS2000MD4
17
400030-043 Rev G
Danaher Motion Superior Electric
SECTION 5: TORQUE VERSUS SPEED
CHARACTERISTICS
5.1 MOTOR PERFORMANCE
All stepper motors exhibit instability at their natural frequency and harmonics of that frequency.
Typically, this instability occurs at speeds between 50 and 1000 full steps per second and,
depending on the dynamic motor load parameters, cause excessive velocity modulation or improper
positioning. This type of instability is represented by the open area at the low end of each Torque
vs. Speed curve.
There are also other instabilities that cause a loss of torque at stepping rates outside the range of
natural resonance frequencies. One such instability is broadly defined as mid-range instability.
Usually, the damping of the system and acceleration/deceleration through the resonance areas aid in
reducing instability to a level that provides smooth shaft velocity and accurate positioning. If
instability does cause unacceptable performance under actual operating conditions, use the
following techniques to reduce velocity modulation.
1)
2)
3)
Avoid constant speed operation at the motors unstable frequencies. Select a base speed
above the motors resonant frequencies and adjust acceleration and deceleration to move
the motor through unstable regions quickly.
The motor winding current can be reduced as discussed in Section 4.5. Lowering the
current reduces torque proportionally. The reduced energy delivered to the motor can
decrease velocity modulation.
Use the half-step mode of operation or use microstepping to provide smoother operation
and reduce the effects of mid range instability. Microstepping reduces the shaft speed
for a given pulse input rate.
SS2000MD4
18
400030-043 Rev G
Danaher Motion Superior Electric
5.2 TYPICAL TORQUE VERSUS SPEED CURVES
The test conditions used when obtaining the torque versus speed data are listed in the
lower left-hand corner of each curve.
SS2000MD4
19
400030-043 Rev G
Danaher Motion Superior Electric
SS2000MD4
20
400030-043 Rev G
Danaher Motion Superior Electric
SS2000MD4
21
400030-043 Rev G
Danaher Motion Superior Electric
SS2000MD4
22
400030-043 Rev G
Danaher Motion Superior Electric
SS2000MD4
23
400030-043 Rev G
Danaher Motion Superior Electric
SS2000MD4
24
400030-043 Rev G
Danaher Motion Superior Electric
SS2000MD4
25
400030-043 Rev G
Danaher Motion Superior Electric
SS2000MD4
26
400030-043 Rev G
Danaher Motion Superior Electric
SS2000MD4
27
400030-043 Rev G
Danaher Motion Superior Electric
SS2000MD4
28
400030-043 Rev G
Danaher Motion Superior Electric
SS2000MD4
29
400030-043 Rev G
Danaher Motion Superior Electric
SS2000MD4
30
400030-043 Rev G
Danaher Motion Superior Electric
SS2000MD4
31
400030-043 Rev G
Danaher Motion Superior Electric
SS2000MD4
32
400030-043 Rev G
Danaher Motion Superior Electric
SS2000MD4
33
400030-043 Rev G
Danaher Motion Superior Electric
SS2000MD4
34
400030-043 Rev G
Danaher Motion Superior Electric
SECTION 6: SYSTEM CHECKING
Motors connected to this drive can develop high torque and large amounts of
mechanical energy.
Keep clear of the motor shaft and all parts mechanically linked to the motor shaft.
Turn off all power to the drive before performing work on parts mechanically
coupled to the motor.
If installation and operating instructions have been carefully followed, this unit should
perform correctly. If the motor fails to step properly, the following checklist will be
helpful in locating and correcting the problem.
In General
Check all installation wiring carefully for wiring errors or poor connections.
Ensure that the proper voltage levels are being supplied to the unit.
Be sure that the motor is a correct model for use with this unit.
Specifically
IF MOTOR DIRECTION (CW, CCW) IS REVERSED, Check For:
Reversed connections to the Motor Connector. Reversing the phase A or the phase B
connections reverses the direction of motor rotation.
IF THE MOTOR MOTION IS ERRATIC, Check For:
Supply voltage out of tolerance.
Proper motion parameters (low speed, acceleration/deceleration, jog speed, home
speed and feed rate). Set parameters on controller supplying pulse input to drive.
Filter capacitor missing or too low in value.
IF TORQUE IS LOW, Check For:
All Windings Off active
Correct current setting.
Improper supply voltage.
IF "FAULT" INDICATOR IS NOT LIT, Check For:
Improper motor wiring.
Grounded or shorted wiring to the motor or shorted motor.
Improper motor type or incorrect Current Select switch setting
If a malfunction occurs that cannot be corrected by making the preceding checks, contact
Customer Support.
SS2000MD4
35
400030-043 Rev G
Danaher Motion Superior Electric
APPENDIX A: TROUBLESHOOTING
A.1 ELECTRICAL INTERFERENCE PROBLEMS
Electrical interference problems are common with today’s computer-based controls. Such
problems are often difficult to diagnose and cure. If such a problem occurs with your
system, it is recommended that the following checks be made to locate the cause of the
problem.
1. Check the quality of the AC line voltage using an oscilloscope and a line monitor. If
line voltage problems exist, use appropriate line conditioning, such as line filters or
isolation transformers.
2. Be certain all recommended wiring practices are followed for location, grounding,
wiring and relay suppression (see Section 3.1).
3. Double-check the grounding connections to be sure they are good electrical
connections and as short and direct as possible.
4. Try operating the drive with all suspected noise sources switched off. If the drive
functions properly, switch the noise sources on again, one at a time, and try to isolate
the one(s) causing the interference problems. When a noise source is located, try
rerouting wiring, suppressing relays or other measures to eliminate the problem.
A.2 CUSTOMER SUPPORT
Danaher Motion products are available nationwide through an extensive authorized
distributor network. These distributors offer literature, technical assistance and a wide
range of models off the shelf for fastest possible delivery.
Danaher Motion sales engineers are conveniently located to provide prompt attention to
customers' needs. Call the nearest office listed for ordering and application information or
for the address of the closest authorized distributor.
In the US and Canada
In Europe
13500-J South Point Blvd.
Charlotte, NC 28273
Danaher Motion GmbH & Co. KG
Robert-Bosch-Straße 10
Phone: (704) 588-5693
Fax: (704) 588-5695
Email: [email protected]
Website: www.DanaherMotion.com
64331 Weiterstadt, Germany
Phone: +49 (0) 6151-8796-10
Fax: +49 (0) 6151-8796-123
Website: www.DanaherMotion.de
SS2000MD4
36
400030-043 Rev G
|