User Guide
MOTOROLA
www.nextel.com
©2010 Sprint. SPRINT and the NEXTEL name and logo are trademarks
of Sprint. Other marks are the property of their respective owners.
4/8/10
FCC Notice to Users
DECLARATION OF CONFORMITY
The following statement applies to all products that have
received FCC approval. Applicable products bear the FCC
logo, and/or an FCC ID in the format FCC-ID: IHDT56KQ1 on
the product label.
Per FCC CFR 47 Part 2 Section 2.1077(a)
Motorola has not approved any changes or modifications to
this device by the user. Any changes or modifications could
void the user’s authority to operate the equipment. See 47 CFR
Sec. 15.21.
Class B Digital Device
Responsible Party Name: Motorola, Inc.
As a personal computer peripheral, this device complies with
part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference
received, including interference that may cause undesired
operation. See 47 CFR Sec. 15.19(3).
Address: 8000 West Sunrise Boulevard
Plantation, FL 33322 USA
Phone Number: 1 (800) 453-0920
Hereby declares that the product:
Product Name: MOTOROLA i1
Model Number: H76XAN9JR9AN
FCC ID: IHDP56KV1
Conforms to the following regulations:
FCC Part 15, subpart B, section 15.107(a), 15.107(d) and section
15.109(a)
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee
that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Ⅲ Reorient or relocate the receiving antenna.
Ⅲ Increase the separation between the equipment and
receiver.
Ⅲ Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Ⅲ Consult the dealer or an experienced radio/TV
technician for help.
Table of Contents
Introduction
Note: Because of updates in phone software, this printed
guide may not be the most current version for your
phone. Visit www.nextel.com and sign in to access the
most recent version of the user guide.
This User Guide introduces you to your wireless service
and all the features of your new phone.
WARNING: Please refer to the Important Safety Information
that will help you safely use your phone. Failure to
read and follow the Important Safety Information
in this phone guide may result in serious bodily
injury, death, or property damage.
Throughout this guide, you’ll find tips that highlight
special shortcuts and timely reminders to help you
make the most of your new phone and service. The
Table of Contents and Index will also help you quickly
locate specific information.
You’ll get the most out of your phone if you read each
section. However, if you’d like to get right to a specific
feature, simply locate that section in the Table of
Contents and go directly to that page. Follow the
instructions in that section, and you’ll be ready to use
your phone in no time.
i
Use and Care
Use
&
Care
Your mobile device is designed to resist damage from
exposure to certain rugged conditions. However, avoid
prolonged or extreme exposure to those conditions. To
help protect your mobile device, always make sure the
battery compartment and any connector covers are
closed and secure, and observe the following
precautions:
extreme heat or cold
Avoid temperatures below 0°C/32°F or
above 45°C/113°F.
shock and vibration
Avoid dropping your mobile device.
liquids
Don’t expose your mobile device to water,
extreme humidity, sweat, or other liquids. If it
does get wet, don’t try to accelerate drying
with the use of an oven or dryer, as this may
damage the mobile device.
dirt
Don’t expose your mobile device to dirt, sand,
food, or other inappropriate materials.
microwaves
Don’t try to dry your mobile device in a
microwave oven.
cleaning solutions
To clean your mobile device, use only a dry
soft cloth. Don’t use alcohol or other cleaning
solutions.
ii
Setting Up Your Phone
1. Setting Up Service
1. Make sure your SIM card is in place.
2. Install the battery.
Ⅲ See “Installing the Battery” on page 6.
ࡗ ࡗ ࡗ ࡗ ࡗ 3. Press and hold End/Power " for two seconds to
turn the phone on.
Ⅲ If your phone is activated, it will turn on, search for
service, and display the home screen.
If your phone's SIM PIN is set, you may be
prompted to enter your SIM PIN code when you
turn on your phone. Press Menu /, enter the
four-digit SIM code, and touch OK to allow phone
transmissions as prompted. (See “SIM Card
Your Phone’s Navigation Pad
Back Key
Home
Key
Speaker Key
Menu
Key
Your Phone” on page 8 for more information.
End/Power
Key
Talk Key
Navigation Key
OK
OK Key
1
4. Follow the onscreen instructions to complete the
MOTOROLA i1 setup wizard.
Getting Started With Your Phone
Your SIM Card
5. Make your first call.
Locating the SIM Card
Ⅲ From the home screen, touch
display the keypad, and then enter a phone
number.
Dialer to
Your SIM (Subscriber Identity Module) card is a small
card inserted into the SIM card holder within your
phone below the battery.
Ⅲ Press Talk `.
Tip: If your phone screen is locked, drag the onscreen
Stretch to unlock button to the right to display the home
screen.
If no SIM card came with your phone, contact Nextel
Customer Service at 1-800-639-6111.
Most users will never need to remove or insert the SIM
card. However, if it becomes necessary, follow the
instructions in “Removing and Inserting the SIM Card”
on page 3.
Note: Your phone’s battery should have enough charge for
your phone to turn on and find a signal, set up your
voicemail, and make a call. You should fully charge
your battery as soon as possible. See “Charging the
Battery” on page 7 for details.
2
Removing and Inserting the SIM Card
Important: The SIM card is designed for optimal Contacts
storage and feature use. For Nextel SIM card
compatibility information, visit
Important: To avoid losing information stored in your SIM
card, do not remove it from your phone unless
absolutely necessary.
In some cases, Contacts and Groups may not be
accessible if you move your SIM card to another
phone. Contacts and Groups created with your
MOTOROLA i1 may not be readable by an older
iDEN SIM-based phone.
To remove your SIM card:
1. With your phone powered off, slide the battery
door latch on the side of the phone down. While
holding the latch down, lift and remove the battery
door.
Note: Your MOTOROLA i1 Contacts are managed and stored
on your phone rather than on the SIM card. If you are
using a SIM card from a previous phone, you can
import your existing contacts from the SIM card to your
MOTOROLA i1 using the SIM Manager. Likewise, you
can export your phone’s Contacts to your SIM card.
details.
3
2. Remove the battery, and then use your thumbs to
carefully slide the SIM card out from under the
edge.
Important: Do not touch the gold-colored areas of your SIM
card.
Note: Protect your SIM card as you would any delicate object.
Memory Card
Store it carefully.
A microSD memory card is provided with your phone.
The provided memory card contains helpful preloaded
information, including guided tours of your phone’s
features.
To insert your SIM card:
1. With your phone powered off, slide the battery
door latch on the side of the phone down. While
holding the latch down, lift and remove the battery
door.
Insert the Memory Card
1. With your phone powered off, slide the battery
door latch on the side of the phone down. While
holding the latch down, lift and remove the battery
door.
2. Remove the battery, and then use your thumbs to
carefully slide the SIM card into your phone until it
lies flat in the SIM card holder.
4
2. Open the memory card slot cover and slide in the
memory card until it clicks into place.
Battery and Charger
WARNING: Use only Nextel-approved or Motorola-approved
batteries and chargers with your phone. The
failure to use a Nextel-approved or Motorola-
approved battery and charger may increase the
risk that your phone will overheat, catch fire, or
explode, resulting in serious bodily injury, death,
or property damage.
Nextel-approved and Motorola-approved batteries and
accessories can be found at Sprint Stores or through
Motorola. You may order online at www.nextel.com or by
calling 1-866-866-7509.
3. Close the memory card slot cover.
Your phone’s Lithium Ion (Li-Ion) battery allows you to
recharge it before it is fully drained.
For more information about your phone’s memory
When the battery reaches 5% of its capacity, your
phone makes a sound and displays a message. When
there are approximately two minutes of talk time left, the
phone sounds an audible alert and then turns off.
5
2. Insert the battery into the opening, making sure the
connectors align. Gently press down to secure the
battery.
Note: Long backlight settings, searching for service, vibrate
mode, browser use, and other variables may reduce
the battery’s talk and standby times. See “Battery Tips”
on page 24 for more details on extending battery life.
Tip: Watch your phone’s battery level indicator and charge the
battery before it runs out of power.
Installing the Battery
1. With your phone powered off, slide the battery
door latch on the side of the phone down. While
holding the latch down, lift and remove the battery
door.
3. Replace the battery door, pressing down firmly on
it to ensure it is secured properly.
6
Removing the Battery
Charging the Battery
1. Make sure the power is off so that you don’t lose
any stored numbers or messages.
Charge your battery as soon as possible so you can
begin using your phone.
2. Remove the battery cover and lift the battery to
remove it.
Always use a Nextel-approved or Motorola-approved
desktop charger, travel charger, or vehicle power
adapter to charge your battery.
Using the Phone Charger
ᮣ
Plug the flat end of the charger into the phone’s
micro USB connector and the other end into the
wall socket connector. Plug the wall socket
connector to an electrical outlet.
WARNING: Do not handle a damaged or leaking battery as
you can be burned.
3H
With the approved Li-Ion battery, you can recharge the
battery before it becomes completely run down.
7
Sleep and Wake Up
Turning Your Phone On and Off
To conserve your battery, prevent
accidental touches, or when you
want to wipe smudges off your
touchscreen, put the touchscreen to
sleep by pressing Screen Lock # on
top of the phone. To wake up the
Turning Your Phone On
ᮣ
Press and hold End/Power " for approximately
two seconds.
Screen Lock
Button
As your phone connects to the network, you see a
connecting message. Your phone may require you to
enter identifying information to use it or to access
specific features.
touchscreen, press Screen Lock # again and then
Stretch to unlock
drag
to the right to unlock the screen.
Activating Your Phone
ⅷ If you purchased your phone at a Nextel Store, it is
probably activated and ready to use.
Note: If your phone's SIM PIN is set, you will be prompted to
enter your SIM PIN code when you turn on your phone.
Press Menu /, enter the four-digit SIM code, and
touch OK to allow phone transmissions as prompted.
ⅷ If your phone is not activated, please call Nextel
Customer Service at 1-800-639-6111 from any other
phone.
Turning Your Phone Off
Press and hold End/Power " to open the Power Key
menu, where you can turn off the phone (Power off), or
turn Airplane mode or Silent mode on or off.
Tip: You must be in an area covered by the Nextel National
Network when you first power up your phone.
ⅷ When you power up your phone the first time, it
performs a series of security checks. For example, it
verifies the phone is Nextel-approved and the correct
SIM card is installed. If you don’t pass the security
checks, your phone displays messages and screen
8
prompts showing what to do next. If you still
encounter security messages, call Nextel Customer
Service at 1-800-639-6111 from any other phone.
Ⅲ Set up additional email accounts, such as POP3,
IMAP, or Microsoft™ Exchange.
Ⅲ Import contacts from your SIM card.
Ⅲ Select your keyboard type.
Setup Wizard
Tip: To type information in any of the setup steps, touch the
text field to display the keyboard. To switch from portrait
(vertical) to landscape (widescreen), turn the phone
counter-clockwise.
The first time you turn on your phone, a setup wizard
appears and helps you get started.
1. (Optional) If you want to change the primary
language used by your phone, touch Change
language and then touch a language.
4. Touch Done to exit the setup wizard.
Note: This phone supports data-intensive applications and
services. It is strongly recommended that you purchase
a data plan that meets your needs. Contact your
service provider for details.
2. Touch Start on the bottom right side of the screen.
3. Follow the onscreen instructions to complete the
wizard. To skip any steps or to proceed after
completing a step, touch Next.
Ⅲ Set up your Wi-Fi connection.
Ⅲ Sign in to your existing Google™ Gmail account.
● If you don’t have a Google account, you can
create one using the wizard.
Tip: Remember to write down your user name and password,
and keep them in a safe place.
9
Setting Up Voicemail
Account Passwords
All unanswered calls to your phone are automatically
transferred to your voicemail, even if your phone is in
use or turned off. Therefore, it is recommended that you
set up your voicemail and personal greeting as soon
as your phone is activated.
With Nextel service, you enjoy unlimited access to your
personal account information and voicemail account.
To ensure that no one else has access to your
information, you need to create passwords to protect
your privacy.
1. Using your MOTOROLA i1, call your wireless phone
number.
Account Username and Password
If you are the account owner, you will create an account
username and password when you sign on to
www.nextel.com. (Click Need to register for access? to get
started.) If you are not the account owner (if someone
else receives the bill for your service), you can get a
sub-account password at www.nextel.com.
2. Follow the system prompts to:
Ⅲ Create your passcode.
Ⅲ Record your name announcement.
Ⅲ Record your greeting.
Note: Voicemail Passcode: It is strongly recommended that
you create a passcode when setting up your voicemail
to protect against unauthorized access. Without a
passcode, anyone who has access to your phone is
able to access your voicemail messages.
Note: When you go to www.nextel.com, you will be redirected
to www.sprint.com by default. Follow the sign in
instructions above to access your Nextel account.
Voicemail Password
For more information about using your voicemail, (see
You will create your voicemail password (or passcode)
when you set up your voicemail. See “Setting Up
Voicemail” on page 10 for more information on your
voicemail password.
10
From Any Other Phone
ⅷ Nextel Customer Service: 1-800-639-6111.
ⅷ Business Customer Service: 1-877-639-8351.
Getting Help
Managing Your Account
Operator Services
Online: www.nextel.com
Operator Services provides assistance when you place
collect calls or when you place calls billed to a local
telephone calling card or third party.
ⅷ Access your account information.
ⅷ Check your minutes used (depending on your
service plan).
ᮣ
Touch
Dialer, 0 and then press Talk `.
ⅷ View and pay your bill.
For more information or to see the latest in products
and services, visit us online at www.nextel.com.
ⅷ Enroll for online billing and automatic payment.
ⅷ Purchase accessories.
ⅷ Shop for the latest phones.
ⅷ View available service plans and options.
From Your MOTOROLA i1
ⅷ Touch
Dialer, *4 and then press Talk ` to
check minute usage and account balance.
ⅷ Touch
Dialer, *3 and then press Talk ` to
make a payment.
11
Your Phone
2. Phone Basics
1. 2.5mm
Headset Jack
16. Screen Lock Button
ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ 1:22 PM
2. Volume
Button
15. Touchscreen
3. Direct
Connect
Button
14. Back Key
Launch PTT
Contacts
13. Speaker
Key
4. OK Key
OK
Call log
Email
Messaging
Browser
12. Camera
Button
5. Home
Key
Note: The use of wireless phones while driving may cause
distraction. Discontinue a call if you can’t concentrate
on driving. Additionally, the use of wireless devices and
their accessories may be prohibited or restricted in
certain areas. Always obey the laws and regulations on
the use of these products.
6. Menu
Key
11. Micro USB
Connector
7. Talk Key
10. End/Power
Key
8. Navigation
Key
9. Microphone
12
10. End/Power Key (") lets you end calls. Press and
hold to open the phone options menu where you
can turn the phone off, turn Airplane mode on or
off, and turn Silent mode on or off.
Key and Connector Functions
1. 2.5mm Headset Jack lets you attach a headset.
2. Volume Button lets you adjust the ringer volume
from the home screen, the voice or speaker
volume during a call, and the speaker volume
while using the music player or other applications.
11. Micro USB Connector lets you connect a charger or
other accessories to your phone.
12. Camera Button (j) activates the camera and lets
3. Direct Connect (DC) Button lets you use Nextel
you take pictures.
13. Speaker Key ()) lets you turn the speaker phone
on or off during a call. From the home screen,
pressing the Speaker Key turns Direct Connect
speaker mode on and off.
4. OK Key (r) selects the highlighted choice when
navigating through a menu using the Navigation
Key.
5. Home Key (X) brings you back to the home
screen. Press and hold to display the active apps
menu.
14. Back Key (%) returns you to the previous screen.
15. Touchscreen input lets you access all the phone’s
menus and features, enter text, dial phone
6. Menu Key (/) lets you access the options menus
(including Settings) from the home screen and
context-sensitive menus from other screens.
numbers, and more, using just your fingertips.
16. Screen Lock Button (#) lets you lock and unlock
the touchscreen.
7. Talk Key (`) lets you make or receive calls,
answer Call Waiting, or switch between two calls.
8. Navigation Key lets you scroll through and highlight
onscreen options.
9. Microphone picks up your voice during a call.
13
The home screen extends beyond what you see on the
initial screen to give you more room for adding
shortcuts, widgets, and more. Flick the home screen
left and right to see more panels or to add widgets or
shortcuts.
Home Screen
The home screen gives you all your latest information
in one place. It’s what you see when you turn on the
phone or press Home X. Here’s the basic setup:
1:22 PM
1:22 PM
1:22 PM
1:22 PM
Status Indicators
Google search
Notifications Bar
Touch & drag this bar down
to check notifications.
Flick left or right to open
more panels.
Call log
Email
Messaging
Browser
Widgets
Touch to open, or touch &
Launch PTT
Contacts
Widgets
hold to move or delete.
You can add widgets, such as a clock, music player, or
appointment calendar, to your home screens.
Shortcuts
Touch to open.
Call log
Email
Messaging
Browser
ᮣ
To add widgets, press Menu / > Add > Widgets
and then select a widget from the list. To open a
widget, touch it
Applications Tab
Drag up to see
all your apps.
Note: Your home screen might look a little different.
14
ᮣ
Touch
(the Applications tab) at the bottom of
Shortcuts
the home screen to open the app menu.
ᮣ
To add shortcuts to the home screen, touch
Running Multiple Apps
(the Applications tab), and then touch and hold the
shortcut you want. When the display switches to
the home screen, drag the short cut to an empty
space. You can also press Menu / > Add >
Shortcuts.
Your phone can run multiple apps simultaneously, so
there is no need to close one app before opening
another one.
To open a new app while another is already running,
press Home X to display the home screen. Touch
and touch the app you want to open. To switch
from one running app to another, press and hold
Home X to display a list of currently running apps,
and then touch the one you want. The list displays up
to six running apps.
Tip: To add widgets or shortcuts, you can also touch and hold
a space on the home screen, touch Shortcuts or
Widgets, and then select an item.
Apps (Applications)
Your phone comes with some apps (applications)
already installed, and you can download and install
more. To open an app, touch its icon.
Search
You can launch a Google search directly from the
home screen.
Applications Tab
All the apps on your phone,
including the apps that came with
your phone and any you
download and install, are listed in
alphabetical order in your
Applications menu.
1. Press Menu / > Search or flick the home screen
to the left to display the search widget.
Alarm Clock
Call log
Browse
ator
Camera
Calendar
Contacts
2. Touch the text field to display the keyboard, and
enter your search term.
Camcorder
15
3. Touch
to begin the search. To use voice
This list identifies the symbols you’ll see on your
phone’s display screen:
search, touch
and say a search topic, such as
“pizza.”
Battery Strength — A fuller battery indicates a
greater charge. The “lightning” icon (bottom
rows) indicates the phone is charging.
Type, then touch the
icon for a text search.
Google search
Signal Strength — More bars next to the
antenna indicate a stronger signal.
Touch for voice
search.
No Service — Your phone is without service.
You cannot make or receive any type of call.
Viewing Status and Notification
Information
Your phone’s display screen provides information
about your phone’s status and notifications. To see
your notifications, touch the notification bar and drag it
down. Icons on the right tell you about your phone’s
status.
Phone In Use — Your phone is active on a
phone call.
Direct Connect In Use — Your phone is active
on a Direct Connect call.
Group In Use — Your phone is active on a
Group Connect call.
1:22 PM
Talkgroup In Use — Your phone is active on a
Talkgroup call.
16
Bluetooth In Use — Your phone is using
Bluetooth. If this icon is blinking, your phone is
in discoverable mode. If this icon is static, a
Bluetooth connection is active.
Internet — You are ready to browse the Internet
or are browsing the Internet using a secure
connection. See “5. Web and Data Services”
Active Phone Line — 1 indicates phone line 1
is ready to make calls; 2 indicates phone line 2
is ready to make calls.
Airplane Mode — Your phone is set not to
receive calls and other transmissions. See
Call Forward — Your phone is set to forward
TTY — You are ready to use your phone to
make calls using a TTY (text telephone) device.
Ringer Off — All sound is turned off on your
Hearing Aid — Your phone is set for use with a
hearing aid and is active on a phone call. See
Speaker Off — Direct Connect sound is set to
come through the earpiece rather than through
the speaker.
Speaker On — Direct Connect sound is set to
come through the speaker rather than through
the earpiece.
Text Message — You have one or more text
Vibrate — Your phone is set to vibrate and not
to ring.
Email — You have one or more emails.
Gmail — You have one or more emails in your
Gmail account.
@
17
Voicemail — You have one or more voicemails.
Navigating Through Menus and
Options
Data Sync — Your phone is downloading email
and synchronizing your calendar with your
personal, Gmail, or Exchange accounts.
Touch Tips
Here are some tips on how to navigate around your
phone.
Wi-Fi — Your phone has established a Wi-Fi
connection.
GPS — Your phone’s GPS is active.
Touch
To choose an icon or option,
touch it.
Downloading — Your phone is downloading
an app.
Call log
Email
essing
Browser
Missed Call — You have one or more missed
calls.
18
Touch and Hold
Tip: When you drag or flick a list, a scroll bar appears on the
right. Drag the scroll bar to move the list to a letter A - Z.
To open special options, touch
and hold an icon or other item.
Try it: In the home screen, touch
Contacts, and then
touch and hold a contact to
open options.
1:22 PM
Flick
Dialer
Call log
Contacts
Favorites
All contacts
To scroll through a list or move quickly, flick your finger
up, down, or across the touchscreen (drag quickly and
release).
Me
Home
PTT
Ashley Grovr
Ashley Grover
View contact
Tip: When you flick through a long list, touch the screen to
stop it from scrolling.
Call Mobilr
Send SMS/MMS
Push to Talk
Zoom
In maps, touch
bottom of the screen to zoom in
or out. When viewing Web
pages, touch the screen once to
zoom in. To zoom out touch the
screen twice, or touch
bottom of the screen.
or
at the
Drag
1:22 PM
To scroll through a list or
move slowly, drag your
Dialer
Call log
Contacts
Favorites
finger up or down the
touchscreen. Try it: In the
home screen, touch
Contacts, and then
drag your Contacts list up
or down.
Als
Me
at the
H
Ashley Grove
Bomi Kim
M
Book Club
Members
Chris Boomer
PTT
Work
PTT
Chris Hunter
19
My Sign
Screen Timeout
Draw on your screen to get to your favorite apps. To
To change how long your phone waits before the
open My Sign, touch
>
My Sign.
screen goes to sleep automatically, touch
>
Settings > Sound & display > Screen timeout.
Draw the sign for the action you
want. For example, draw a “V” to
go to voicemail.
1:22 PM
To put your phone to sleep and lock your screen, see
To see which actions are already
assigned to gestures, press
Menu / > List Gestures. You’ll
also see several gestures that
are unassigned.
Adjust Volume
Press the Volume button to change
the ring volume (in the home
screen), or the earpiece volume
Volume
Button
(during a call).
To assign an action to a gesture,
press Menu / > List Gestures,
touch an unassigned gesture,
and then touch an app from the
list.
Call Voicemail
1-555-555-5555
Rotate the Screen
The touchscreen can rotate 90 degrees to switch
between portrait (vertical) and landscape (widescreen)
modes when you rotate your phone.
To create a new gesture, press Menu / > New
Gesture, select an action from the list, and draw a
gesture to assign to the action.
To set your screen to rotate automatically:
ᮣ
Touch
>
Settings > Sound & display >
Orientation.
Tip: Not all applications are designed to rotate.
20
Displaying Your Numbers
Entering Text
Touch
Contacts and select the first contact. The
Touchscreen Keyboard
first contact in the Contacts list will always contain your
phone’s information.
You can open a display keyboard by touching a text
field. To close the keyboard, press Back %.
1:22 PM
Text Entry
Touch to open the
Dialer
Call log
Contacts
Favorites
touchscreen keyboard.
All contacts
Search
Touch to search
contacts.
Search contacts
Me
My Info
Your details–always
first in the list.
Delete
Return
Home
PTT
Ashley Grover
Bomi Kim
Contacts List
Touch to view
contact information.
Touch & hold to edit,
delete, and more.
Mobile
PTT 1
Shift
Space
Symbols/Numbers
Book Club
3 Members
PTT 1
Note: To automatically rotate the touchscreen to be right-side
up when you rotate the phone, touch
Menu Options
Press Menu
create, filter, and
sync contacts.
Chris Boomer
>
to
Settings > Sound & display > Orientation.
21
Select Keyboard Type
Android Keyboard Typing Tips
You can change the type of keyboard you’re using by
touching and holding a text field and then touching
Input method.
Here are some tips for using your phone’s Android
keyboard:
To…
Options
?123
Enter numbers Touch
or symbols
. To return to the
ABC
Android
keyboard
Standard keyboard.
standard keyboard, touch
.
?123
ALT
Enter alternate
characters
Touch
from the
screen. To
?123
ALT
Swype™
Keyboard for single hand text
entry. Slide your finger from one
letter to the next to enter text.
return to the
again.
screen, touch
Enter one
capital letter
Touch Shift
Touch Shift
Touch Delete
.
Enter only
capital letters
twice.
XT9 Text Input
Offers improved foreign language
support and word prediction.
DEL
x
Delete
. Touch and hold
to delete more than one character.
Start a new line Touch Return
.
22
Swype Typing Tips
Swype™ Text Entry
ⅷ To enter apostrophes in common words (like “I’ll”),
drag through the n as though it was an apostrophe.
Swype lets you enter a word with one continuous
motion. To enter a word, just drag your finger over the
letters.
ⅷ To enter several symbols, touch SYM.
_
EN
@
q
w
e# r 1 t2 y3
u
i% o ( p)
day
ⅷ To correct a word, double-tap it. Swype shows a
small menu of other word options. Swype might also
show a menu if it can’t guess your word.
“
a8 s$ d4 f 5 g6 h+ j : k ;
l
‘
ⅷ If Swype doesn’t know a word, you can still touch the
letter keys to enter it. Swype remembers, so next time
you can just drag over the letters.
z ! x7 c8 v9 b0 n/ m?
,
.
_
SYM
SYM
SYM
_
EN
@
Text Entry Settings
When you use the touchscreen keyboard, your phone
suggests words from your dictionary and chosen
language.
book
q
w
e# r 1 t2 y3
u
i% p)
a8 s$ d4 f 5 g6 h+ j : k ;
l
“
For double
letters, circle
the letter.
‘
z ! x7 c8 v9 b0 n/ m?
,
.
_
Touch
>
Settings > Locale & text.
ⅷ To change the language and the style for your
touchscreen keyboard, touch Select locale.
_
EN
@
Who
q
w
e# r 1 t2 y3
u
i% o ( )
“
To
ⅷ To edit your dictionary, touch User dictionary.
a8 s$ d4 f 5 g6 hj : k ;
l
capitalize,
go above
the
ⅷ To change the sounds, corrections, and other
settings for your touchscreen keyboard, touch
Android keyboard, Swype, or XT9 Text Input.
‘
z ! x7 c8 v9 b0 n/ m?
,
.
_
keyboard.
23
Battery Tips
Tips and Tricks
Your phone is like a small computer, giving you access
to a lot of information and apps, with a touch display.
Depending on what you use, that can take a lot of
power.
General Tips
To…
Return to the
Press Home X.
To conserve battery life between charges:
home screen
ⅷ Reduce recording or watching videos, listening to
music, or taking pictures.
Press Talk `.
See your
Call log
ⅷ Disable or remove widgets that stream information to
your home screen, such as news or weather. (See
Press Screen Lock #.
Sleep/wake
your phone
ⅷ Reduce email updates: touch
>
Email >
Touch
>
Settings >
Set screen
timeout
Menu / > More > Account settings > Email check
frequency > Every hour or Never to check for email
manually.
Sound & display > Screen timeout.
Press and hold End/Power " >
Silent mode.
Turn sound
on/off
ⅷ Turn off Bluetooth power: touch
>
Settings > Wireless controls > Bluetooth.
Search
Press Menu / > Search.
ⅷ Turn off Wi-Fi: touch
Wireless controls > Wi-Fi.
>
Settings >
Press and hold Home X.
Show last few
apps used
ⅷ Disable Google™ app updates: touch
Settings > Data synchronization > Google >
Background data.
>
Press and hold End/Power " >
Airplane mode.
Turn airplane
mode on/off
24
ⅷ Reduce display brightness: touch
Settings > Sound & display > Brightness > (dimmer
setting).
ⅷ Decrease display timeout delay: touch
>
in “Cool Down” mode, only emergency calls can be
made.
>
Accessories
Settings > Sound & display > Screen timeout >
(shorter setting).
Your MOTOROLA i1 comes with the following
accessories:
Rugged Features
ⅷ A Li-Ion battery and charger.
ⅷ A128K SIM card.
Your phone is designed to resist damage from
exposure to certain rugged conditions. To help protect
your phone, always make sure that the battery
compartment and connector covers are closed and
secure. You should also avoid prolonged or extreme
exposure to those conditions.
Various accessories are available for use with your
MOTOROLA i1, including cases, vehicle power
chargers, data cables, hands-free accessories, and
more.
To order additional accessories, go to www.nextel.com
or call1-866-866-7509. You can also contact your
Nextel Authorized Representative or stop by any Sprint
Store. For information on Sprint Store locations, go to
Battery Cool Down
In very limited circumstances, such as where your
phone has been exposed to extreme heat, “Cool
Down” message screens will appear. To avoid possible
damage to your battery and phone, you should follow
these instructions until the phone is within its
recommended temperature range. When your phone is
25
Using a Remote Direct Connect Button
If you are using a headset or other optional accessory
with a remote Direct Connect button, you can use the
remote Direct Connect button for phone calls, Direct
Connect calls, and Group Connect calls.
For phone calls, use the remote Direct Connect button
to answer calls, switch between calls, and end calls.
Hold the remote Direct Connect button for less than
two seconds to answer calls and switch between calls.
Hold the remote Direct Connect button for more than
two seconds to end calls.
For Direct Connect calls and Group Connect calls, use
the remote Direct Connect button as you would the
Direct Connect button on your phone.
When using a headset, the Direct Connect button on
your phone works the same way as when you are not
using a headset. Direct Connect and Group Connect
sounds will be heard through the headset.
26
ⅷ Direct Connect Calls allow two-way radio
communication with another Direct Connect user
within the Nextel National Network (page 32).
3. Making and Answering
Calls
ⅷ Group Connect Calls allow coast-to-coast two-way
radio calling to up to 20 Nextel Direct Connect
customers simultaneously (page 35).
ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ⅷ Nextel Direct Send allows you to send contact
information in Direct Connect and Group Connect
calls and send pictures in Direct Connect calls
ⅷ Talkgroup Calls allow two-way radio calling to up to
100 Nextel Talkgroup customers simultaneously
Note: To learn more about the differences between Nextel
Group Connect calls and Talkgroup calls, please see
Types of Calls
With the Nextel National Network, Nextel Direct
Connect, and your MOTOROLA i1, you have the
following traditional wireless phone and Nextel Direct
Connect services available to you:
ⅷ Digital Wireless Phone Calls offer clear calls and other
services, such as missed call notification, Three-Way
Calling, and speakerphone.
27
Phone Calls
1:22 PM
Making Calls
Dialer
Call log
Contacts
Favorites
Placing a traditional wireless phone call from your
MOTOROLA i1 is as easy as making a call from any
landline phone.
Delete
Touch to delete a digit you
entered.
555-555-5555
1
2
3
ABC
DEF
Contacts
Touch to open, then touch
an entry to call.
1. Touch
press Talk `.
Dialer, enter a number, and then
4
5
6
2. Press End/Power " when you are finished.
GHI
JKL
MNO
Call Log
Touch to open, then touch the
icon to the left of an entry to
call.
You can also make calls from your phone by selecting
8
9
7
PQRS
TUV
WXY
Call
0
#
Enter a number and
*
+
press
.
Answering Calls
ᮣ
Press Talk ` to answer an incoming call.
Note: When your phone is off, calls go directly to voicemail.
Your phone notifies you of incoming calls by any
combination of ringing or vibrating, the backlight
28
illuminating, or the screen displaying an incoming call
message.
Emergency Calls
Your phone supports emergency calling. Emergency
phone calls can be made even when your SIM card is
blocked or not in your phone.
If the incoming call is from a number stored in your
Contacts, the entry’s name is displayed. The caller’s
phone number may also be displayed, if available.
ᮣ
Touch
Dialer, enter 911 and press
Ending a Call
Talk ` to be connected to an emergency
response center. If you are on an active call, you
must end it before calling 911. If your phone is
locked, touch the Emergency call button at the
bottom of the screen.
ᮣ
To end a call, press End/Power ".
Missed Phone Calls
Missed phone calls are forwarded to voicemail. When
you do not answer an incoming call, you will see a
Missed Call notification.
When you make an emergency call, your phone’s GPS
Enabled feature can help emergency service
personnel find you, if you are in a location where your
phone's GPS antenna has established a clear view of
the open sky and your local emergency response
center has the equipment to process location
information. See “GPS and AGPS” on page 129.
Because of the limitations of this feature, always
provide your best knowledge of your location to the
emergency response center when you make an
emergency call.
To display a Missed Call entry from the notification bar:
ᮣ
Drag the notification bar down and touch the
missed call notification.
To display a Missed Call entry from the home screen:
1. Press Talk ` or touch
Dialer > Call Log.
2. Touch an entry.
29
In-Call Options
Important: Always report your location to the 911 operator
when placing an emergency call. Some
designated emergency call takers, known as
Public Safety Answering Points (PSAPs) may not
be equipped to receive GPS location information
from your phone.
Press Menu / during a call to
display a list of available in-call
features. To select an option,
touch it. The following options
may be available:
1:22 PM
If you have not registered on the network,
emergency calls cannot be placed while your
SIM card is in your phone.
ⅷ Swap call to switch between to
active calls.
Show Dialpad
ⅷ Merge call to initiate a three-
If you are bringing your phone number to Nextel
from your previous carrier, you may receive a
temporary telephone number while your Nextel
phone is being programmed with your
permanent phone number. If you make a call to
911 and the call fails, the 911 emergency
response center will not be able to call you back
on your Nextel phone if in the meantime, your
Nextel phone has been programmed with your
permanent telephone number. If the call is
disconnected before location and details have
been provided, call 911 again and advise that you
were disconnected.
way call.
Swap call
Hold
Merge call
Mute
Add call
Speaker
End call
Bluetooth
ⅷ Add call to place a second call.
ⅷ End call to end the call.
ⅷ Hold to place a call on hold.
ⅷ Mute to mute your phone’s microphone. Touch Mute
again to unmute your phone’s microphone.
ⅷ Speaker to route the phone’s audio through the
speaker or the earpiece.
Tip: You can also press Speaker ) to turn the speaker on
and off.
WARNING: Because of higher volume levels, do not place the
phone near your ear during speakerphone use.
30
ⅷ Bluetooth to disconnect from a Bluetooth device.
2. Touch Search contacts.
3. Enter the first few letters of a Contact's name. Your
phone will display a list of matching contact
entries.
Saving a Phone Number
1. Touch
Dialer, enter a phone number, and
press Menu /.
4. To display the Contacts entry, touch the contact
name. Touch a phone number to place a call.
2. Touch Add to contacts.
3. To store a new entry, touch Create new contact.
Phone Numbers With Pauses
You can dial or save phone numbers with pauses for
use with automated systems, such as voicemail,
conference call, or credit card billing numbers.
– or –
Search for an existing contact name and touch it to
open the contact.
4. Enter or edit information as necessary, and then
scroll to the bottom of the entry and touch Done to
save the Contact.
There are two types of pauses available on your phone:
ⅷ Wait sends the next set of numbers when prompted.
ⅷ Pause automatically sends the next set of numbers
after three seconds.
For more information about Contacts, see “8. Contacts”
Note: You can have multiple pauses in a phone number and
combine waits and pauses.
Finding a Number
To dial or save phone numbers with pauses:
To find Contacts entries, you can either scroll through
the list by dragging your finger up or down the screen,
or you can search Contacts entries by name.
1. Touch
Dialer and enter a phone number.
2. Touch and hold * until the letter P appears. The P
represents a three-second pause. For a longer
1. Touch
Contacts.
31
pause, touch and hold * again to enter more
pauses. Each P represents a three-second pause.
Making a Call From the Call Log
1. Touch
Dialer > Call Log.
– or –
2. Touch the icon to the left of an entry to place a call.
Touch and hold * until the letter W appears. The
W means your phone waits before dialing further. A
message appears asking about sending the rest of
the digits.
Making a Phone Call While in a Direct
Connect Call
3. Enter additional numbers.
4. Press Talk ` to dial the number.
– or –
ᮣ
Press Menu / > Call contact while in an active
Direct Connect call to initiate a phone call to the
other person (if their mobile phone number is
stored in Contacts).
Press Menu / > Add to contacts to save the
number in your Contacts.
Nextel Direct Connect
Making a Call From Contacts
Nextel offers the following Nextel Direct Connect®
services:
ⅷ Direct Connect® allows instant two-way radio
communication with another Direct Connect user
anywhere on the Nextel National Network (U.S.).
1. Touch
Contacts.
2. Touch an entry to open it.
3. Touch a phone number to place a call.
ⅷ International Direct Connect allows Direct Connect
calling to and from select countries.
32
ⅷ Group Connect® allows nationwide Direct Connect
calling to up to 20 other Direct Connect users at
once. (See “Group Connect” on page 35.)
ⅷ TalkgroupSM allows Direct Connect calling to up to
100 Nextel subscribers in the same Direct Connect
Dialing Direct Connect Numbers
Every Direct Connect number has three parts:
ⅷ An area ID.
ⅷ A network ID.
ⅷ A member ID.
Connect services. Pricing for each of these services is
based on your service contract.
An asterisk separates each part (for example:
999*999*9999). When you enter a number containing
all three parts, you must separate them with asterisks.
Note: The number of digits in each part of a Direct Connect
number may vary. For example, your Direct Connect
number may be formatted as 999*999*9999, while
another valid number may appear as 555*555555*55.
Making Direct Connect Calls
1. Touch
Dialer and enter a Direct Connect
If you are calling or saving a Direct Connect number for
a Sprint phone with Direct Connect capabilities, the
Direct Connect number may be the same as the
wireless phone number. When dialing or saving the
Direct Connect number, insert asterisks in place of
hyphens (913*555*1234).
2. Press and hold the Direct
Connect (DC) button on the left
side of your phone. Begin
talking after your phone emits
a chirping sound.
Direct
Connect
Button
Tip: When you store a Direct Connect number in Contacts, be
3. Release the DC button to listen.
sure to include the entire number, including the asterisks.
A Direct Connect call ends automatically after there is
no activity on the call for several seconds.
33
Using Just the Member ID
Answering Direct Connect Calls
If you are contacting someone sharing your network
and area IDs, you only need to enter the member ID
(the last part of the number).
When you receive a Direct Connect call, your phone
emits a tone or vibrates. You then hear the voice of
your caller.
1. Touch
Dialer and enter a member ID.
1. Wait for the caller to finish speaking.
2. Press and hold the DC button.
2. Press and hold the DC button. Continue as you
would on any Direct Connect call.
Making Direct Connect Calls From Contacts or
the Call Log
A Direct Connect call ends automatically after there is
no activity on the call for several seconds.
If you have numbers stored in Contacts (page 82) or
make calls.
Direct Connect Timeout
You can extend the automatic timeout of a Direct
Connect call by about 30 seconds using the Resume
DC setting.
1. Touch
Contacts, or touch
Dialer >
Call log.
2. Touch an entry and then press and hold the DC
button to call the entry’s Direct Connect number.
ᮣ
Touch
>
Settings > Call settings >
Direct Connect settings > Resume DC.
Tip: You can make Direct Connect calls while viewing entry
details on either list. Display the entry details or My Info
from another phone (in the Call log) and press and hold
the DC button.
34
One Touch Direct Connect
You can customize the DC button for quick access to
Direct Connect functions.
Group Connect
A Group Connect call is similar to a Direct Connect call
to one user, but is made to multiple Direct Connect
subscribers at once. You can create Groups from your
phone and call up to 20 other Group Connect-
compatible phones* anywhere on the Nextel National
Network. You can create a Group for one-time use or
store it to Contacts so you can call it at any time.
ᮣ
Touch
>
Settings > Call settings >
Direct Connect settings > One Touch DC.
Options
Off
Turn off One Touch DC.
Launch DC
Contact List
Open a list of Direct Connect
contacts on your phone.
Note: In order to store Groups to your MOTOROLA i1, you
must use the 128K SIM card that came with your
phone. The 128K SIM card is labeled “Nextel 600
Contcs & 25 Grps”. With this SIM card, a maximum of
25 groups can be added to your MOTOROLA i1. Group
entries created with your MOTOROLA i1 may not be
readable by older iDEN SIM-based phones.
DC a selected
contact
Start a Direct Connect call with the
selected contact.
DC the most
recent number
Start a Direct Connect call with the
most recent Direct Connect
number in the Call log.
Tip: You can also add the One Touch DC widget to your
Making Group Connect Calls
1. From Contacts or the Call log list, touch a Group to
open it.
2. Press the DC button.
.
35
3. Touch Add Members and select members to add.
Answering Group Connect Calls
4. Touch Done(Selected) and then scroll to the
bottom of the entry and touch Done to save the
contact.
ᮣ
Proceed as if answering a Direct Connect call from
one user. Only one person at a time may speak on
a Group Connect call.
Starting a Group Connect Call With a
Direct Connect Number
Creating Groups in Contacts
1. Touch
Contacts > Menu / > New group.
1. Touch
Contacts > Menu / > New group.
2. Touch the icon to the left of the entry names to
select the group members.
2. Select the group members.
3. Touch View.
3. Touch Save(Selected) to store the Group in
Contacts.
4. When prompted, press the DC button.
Note: If you do not assign a name, the Group is named
(Group).
Removing Members or Groups
4. Scroll to the bottom of the entry and touch Done.
To remove a member from a Group:
1. From Contacts, touch a Group to open it, and then
press Menu / > Edit group.
Adding Group Members
To add member to a Group stored in Contacts:
2. Touch a member’s contact to remove it from the
Group.
1. Touch
Contacts and touch a Group to
open it.
3. Scroll to the bottom of the entry and touch Done.
2. Press Menu / > Edit group.
36
To delete a Group from Contacts:
1. Touch a Group to open it.
2. Press Menu / > Delete group.
3. Touch OK.
ⅷ The number of members who are participating in the
Group Connect call.
Nextel Direct Send
Nextel Direct Send lets you use Direct Connect calls to
exchange pictures, My Info, contact information, and
Groups with other phones that have this capability.
Storing Groups
To store a group to Contacts from the Call log list:
Nextel Direct Send cannot be used during Talkgroup
calls. Pictures cannot be sent in Group Connect calls.
1. From the Call log list, touch a Group to open it, and
then touch View participant list.
Sending a Picture
2. Touch Add to contacts.
3. Scroll to the bottom of the entry and touch Done to
Sending a Picture During a Call
save the contact.
You can send a picture at any time during a Direct
Connect call, whether you made or received the call.
(Additional charges may apply.)
Group Connect Call Information
While you are in a Group Connect call, the following
appears on the screen:
You cannot talk or listen on a Direct Connect call while
a picture is being transmitted. Other activities, such as
searching for a picture, do not prevent you from talking
or listening.
ⅷ The name of the Group.
ⅷ The name or the Direct Connect number of the
person speaking.
37
To send a picture during a call:
Tip: When a person sends you My Info from his or her phone,
you can then easily store this information to Contacts
from the Call log list.
1. While in a Direct Connect call, press Menu / >
Share picture. A list of pictures that can be included
in a Direct Connect call appears.
To start a call by sending a picture:
2. Select a picture and press the DC button to send it.
1. Touch
>
Media Gallery > All Pictures.
3. Wait while the picture is transmitted. The Direct
Connect call is temporarily interrupted while a
picture is transmitted.
2. Touch and hold a photo, then touch Share.
3. Touch DC, and touch DC contacts or DC call log.
These names have Direct Connect numbers and
IP addresses stored.
4. When prompted, press the DC button to resume
the Direct Connect call.
4. Select a name and press the DC button to send
the picture.
Note: The first time you send a stored picture after turning the
phone on, the message Picture fees may apply
appears and you are prompted to respond. Touch OK
to send the picture. Touch Cancel to cancel.
5. When prompted, press the DC button to resume
the Direct Connect call.
Starting a Call by Sending a Picture
Receiving a Picture
You can start a call by choosing a stored picture from
the Media Gallery.
When someone sends you a picture using Nextel
Direct Send, your phone emits a tone or vibrates and a
message appears on the display asking you to accept
the picture.
To do this, you must have the recipient’s Direct Connect
number and IP address stored in your Contacts.
Pictures you receive are saved to your phone’s memory
and are accessible through the Media Gallery.
38
To accept a picture:
Sending My Info
1. When you see the message asking you to accept
the picture, touch Accept. (To decline the picture,
touch Reject.)
You can control what portion of the information in My
Info is sent, and whether it is sent automatically in every
Direct Connect call or only when you choose to send it.
2. Wait while the picture is transmitted. The Direct
Connect call is temporarily interrupted while a
picture is transmitted.
Note: When you send your contact information, certain
information, such as street addresses or custom entries,
chat addresses, organizations, and notes cannot be
included.
3. When prompted, press the DC button to resume
the Direct Connect call.
The information your phone sends always includes My
Name and Direct Connect.
Note: The first time you accept a stored picture after turning
the phone on, the message Picture fees may apply
appears and you are prompted to respond. Touch OK
to accept the picture. Touch Cancel to cancel.
It may include Line 1, Line 2, Direct Connect, and Group
ID depending on the options provided by your service
provider and how you set your sending options.
Tip: To stop the transmission before it is finished, touch
Note: The My Info feature gets its information from your
phone’s contact entry. To add more information to My
Info, edit your phone’s contact entry, and then select the
additional fields in the Select info to share screen.
Cancel.
Sending My Info and Contact Information
The default setting is Line 1 only.
When you send My Info or contact information using
Nextel Direct Send, the information you send appears
on the display of the receiving phone. After the call, the
information appears on that phone’s Call log list.
To change which fields are sent:
1. Touch
>
Settings > Call settings >
Direct Connect settings > Sharing contact info >
Select info to share.
39
2. A checkmark appears next to the fields that will be
3. Touch Share via DC.
sent. To add or remove the checkmark, touch it.
4. Touch a Contact or Call log entry to select it.
3. When you are finished, touch Save.
5. When prompted, press the DC button to send the
information.
To control whether your information is sent automatically:
ᮣ
Touch
>
Settings > Call settings >
Sending Contact Information
Direct Connect Settings > Sharing contact info >
Share My Info.
You can send contact information by selecting a
Contacts entry.
Note: When you receive your phone, it is set to send your
Contacts entries that contain only addresses cannot be
sent. When Contacts entries are received, they do not
include ringtones or pictures.
information automatically.
To send My Info during a call:
1. While in a Direct Connect call, press Menu / >
To send contact information during a call:
Share my info.
1. While in a Direct Connect call, press Menu / >
Share contact.
2. When prompted, press the DC button to send the
information.
2. Select a contact to send
To start a call by sending My Info:
3. When prompted, press the DC button to send the
information.
1. Touch
Contacts.
2. Touch and hold the contacts entry containing your
Note: If the Contacts entry you scrolled to is a Group, you may
be prompted to allow yourself to be a part of the group
being sent. Touch OK to become part of the group.
phone’s information. This contact will always be the
first entry in the contacts list and will have
its right.
to
40
To start a call by sending contact information:
Talkgroups
1. From Contacts, touch and hold a contacts entry.
A Talkgroup is a predetermined group of Direct
Connect users, created by an account administrator.
Talkgroups can contain up to 100 members.
2. Touch Share via DC.
Note: If the Contacts entry you scrolled to is a Group, you may
be prompted to allow yourself to be a part of the group
being sent. Touch OK to become part of the group.
Difference Between Group Connect and
Talkgroup Calls
In a Group Connect call, you or another caller
determines who can participate in the call. By contrast,
participation in a Talkgroup is determined by an
administrator. Here are the ways Group Connect and
Talkgroup calls differ.
3. Select a recipient by touching a DC Contact or DC
Call Log entry.
4. When prompted, press the DC button to send the
information.
Receiving My Info or Contact Information
When you receive My Info or contact information from
Group Connect Talkgroup
another phone,
To view the information while still in the Direct Connect call:
Press Menu / > View Contact.
appears on the display.
Group Icons
Nationwide
Limited to local
market and network
(fleet)
Geography
ᮣ
You can also view My Info from other phones on the
21 (including
originator)
100
Maximum
Group Size
41
Adding More Talkgroups
Group Connect Talkgroup
Dynamically,
via your phone administrator using
Talkgroup
Predefined, via Nextel
Setup
You can be included in additional Talkgroups by doing
one of the following:
must be an account administrator to use Talkgroup
Management.
Management
Joining a Talkgroup
To participate in a Talkgroup, the account administrator
must first add you to the membership and then you
must “join” the Talkgroup.
ⅷ Contacting your Nextel Sales Representative at the
time of activation.
Making Talkgroup Calls
1. Touch
open it.
Contacts and touch a Talkgroup to
1. Touch
Talkgroup number.
– or –
Dialer, touch
, and then enter the
+
2. Touch Join.
You can now receive communications from other
members of this Talkgroup.
Select the Talkgroup from Contacts or the Call log
list.
You will hear all active Talkgroup conversations on your
2. Press the DC button and continue as if making a
Direct Connect call.
phone. To silence them, touch
>
Settings >
Call settings > Direct Connect settings > Silence
Talkgroups.
42
Receiving Talkgroup Calls
Note: You can send a Call Alert from the Call log or Contacts.
Touch an entry with a Direct Connect number and then
touch Send Alert.
ᮣ
Answer it as you would a regular Direct Connect
call. Only one person at a time may speak on a
Talkgroup call.
Responding to a Call Alert
During and immediately after a Talkgroup call ends,
press Menu / > Options to display any available
options.
Note: You can set a distinctive ringer for Call Alerts. See
To answer a Call Alert:
Call Alerts
ᮣ
Press the DC button. This will start a Direct
Connect call to the sender.
Call Alerts let you notify others that you want to
communicate with them using Direct Connect. When a
user receives a Call Alert, the phone sounds a tone
and displays your name or Direct Connect number.
To dismiss a Call Alert:
Touch Dismiss.
To store a Call Alert in Notifications:
Touch Later.
ᮣ
Sending Call Alerts
ᮣ
1. Touch
Dialer, enter a Direct Connect
number and press Menu / > Send Alert.
Note: The Call log list also stores Call Alerts you have
received. They appear as Direct Connect calls. Call
Alerts remain in your Call log list until you delete them
or until they reach the end of the list.
2. When prompted, press the DC button to send the
Call Alert.
43
3. Press the DC button to begin the call.
This removes the Call Alert from the queue.
To send a Call Alert to the sender:
Using the Call Alert Notification
When you store a Call Alert, it remains in notifications
until you clear the notification by opening it, or go into
the Call log.
1. Touch
Dialer > Call log.
Viewing Call Alerts
2. Touch a Call Alert entry to open it and touch Send
Alert.
1. Drag the Notification bar down from the top of the
screen.
3. When prompted, press the DC button.
Deleting Call Alerts
2. Scroll through the list.
Viewing Call Alert Date and Time
1. Touch the Call Alert notification.
To delete all Call Alerts from Notifications:
1. Drag the Notification bar down from the top of the
screen.
2. In the Call log screen, touch the Call Alert.
2. Touch Clear notifications.
Responding to Call Alerts in the Queue
Note: Touching Clear Notifications will clear all of your
After you queue a Call Alert, you can respond to it by
making a Direct Connect call to the sender or sending
a Call Alert to the sender.
Notifications, not just your Call Alerts.
To make a Direct Connect call to the sender:
1. Touch the Call Alert notification to open the Call
log.
2. Touch the Call Alert Entry.
44
Call Status and Completion
After an failed incoming or outgoing Direct Connect
call or Call Alert, you can send a message to the caller
or intended recipient.
To set up a message for incoming or outgoing calls:
1. Touch
>
Settings > Call settings > Auto
Text reply > Incoming call or Outgoing call.
2. Select from Off, Ask me to send text, or Always send
text.
3. Create a message to be sent, and touch Update.
To send a message after receiving or making a call:
1. After a failed incoming or outgoing Direct Connect
call, within five seconds, Send text message to will
appear.
2. Touch your default message to send it, touch
Create new message to send a new message, or
touch Cancel.
45
Receiving Messages
4. Service Features:
The Basics
When you receive a Multimedia Messaging Service
(MMS) message, or text message (SMS), you have two
ways to access the message:
ⅷ Respond to the message notification that appears
when the message is received.
ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ⅷ Access the message later through Messaging.
Message Notifications
When you receive a message, your phone notifies you
with an icon in the notification bar and a notification
tone or vibration.
For information on notification options, see “Setting
46
your password. Enter the last seven digits of your
Nextel PTN. For example: 5557777. This is your
temporary password. Follow the system instructions to
complete your mailbox setup.
Voicemail
Tip: To receive voicemail messages, you must first set up your
voicemail box.
You are in the main voicemail menu when you hear the
voicemail system options.
If you are bringing your phone number from another
carrier, we suggest you set up your voicemail box after
the number you brought to Nextel is active on your Nextel
phone and your temporary phone number is deactivated.
If you set up your voicemail box prior to this, all messages
and all settings (including your greeting and password)
will be lost when the number you have brought to Nextel
becomes active.
For details on using your voicemail, follow the audio
prompts provided by the voicemail system.
Playing Messages
ᮣ
To listen to your voicemail messages Touch
Dialer and touch and hold 1. You will be
connected to your voicemail box.
Setting Up Your Voicemail Box
ᮣ
To access your voicemail messages from another
phone, dial your wireless phone number. When
you hear the voicemail greeting, press * and then
enter your voicemail passcode.
Using your MOTOROLA i1, dial your ten-digit Nextel
Personal Telephone Number (PTN). For example:
7035557777. Follow the system instructions to create a
new four- to seven-digit password, record your name,
and record a greeting. When the system says, “Thank
you for using Nextel Voicemail,” your mailbox is set up.
Multimedia Messages (MMS)
If you are setting up your voicemail from a phone other
than your MOTOROLA i1, dial your ten-digit Nextel PTN.
When you hear the greeting, press * to access your
voicemail box. The system will prompt you to enter
Multimedia Messaging Service (MMS) lets you send
and receive messages that may include text, pictures,
and audio recordings.
47
Your MMS address is [email protected].
Your PTN is your ten-digit Nextel Personal Telephone
Number.
ⅷ Subject — the subject line. To add a subject, press
Menu / > Add subject and enter a subject.
ⅷ Attach — one or more attachments. These may be
pictures, ringtones, or audio files, including voice
records that you create while creating the message.
To add an attachment, press Menu / > Attach.
Note: Most common phone-to-phone text messages are sent
and received as MMS messages on your MOTOROLA
i1. Text messages sent from other phones or mobile
devices to your phone number arrive as MMS
messages.
To send a message, you must address it to at least one
recipient. All other message fields are optional and you
can fill them in any order.
Accessing MMS Messages
Entering Text
ᮣ
Touch
To open a message:
Touch a message thread.
>
Messaging.
In message fields that require you to enter text, touch
the message field to display the keyboard. If the
keyboard is already displayed, begin typing whenever
the field is highlighted.
ᮣ
Creating and Sending Messages
Each message you create may contain the following
fields:
Message Size
You can create and send messages of up to 100 KB,
including attachments, for MMS.
ⅷ To — the phone numbers or email addresses of one
or more recipients.
ⅷ Message — the body of the message. This may
include text, pictures, ringtones, or voice records.
48
Sending or Canceling
Adding More Message Options
To send the message at any time after it has been
addressed:
1. To create the subject line, press Menu / > Add
subject, enter a subject, and touch Next.
2. To attach a picture, audio, voice recording, or
video, press Menu / > Attach and then select an
option to attach a file.
ᮣ
Touch Send.
Creating a Message
1. Touch
>
Messaging > New message.
3. To send the message, touch Send.
2. Address the message:
Replying to a Message
Ⅲ Touch To. Enter the phone number, contact name
or email address from the keyboard. Use a
comma to separate multiple phone numbers or
email addresses. Once you begin typing, your
phone will show a list of contacts that are possible
matches for the letters you have typed.
You can reply to a message while you are viewing it.
To reply to a message:
1. Touch a message to open it.
2. Touch the message field at the bottom of the page
to enter your message.
3. Enter or edit the body of the message:
Ⅲ Touch the message field and then enter text using
3. Touch Send.
the keyboard.
More Ways to Begin a Message
4. To send the message without additional options,
In addition to beginning a message from Messaging,
you can begin a message from Contacts, the Call log
list, the home screen, or the Media Gallery.
touch Send.
49
To begin a message from Contacts:
1. From the Contacts list, touch an entry.
2. Touch Text mobile.
Accessing Saved Drafts
1. Touch
>
Messaging.
2. Draft messages have “Draft” in red letters next to
them on the right.
3. Create and send the message.
To begin a message from the Call log list:
1. From the Call log list, touch an entry.
2. Touch Send text message.
3. Touch the message to open it and finish
composing your message.
Forwarding Messages
3. Create and send the message.
To begin a message from the Media Gallery:
1. Touch
>
Messaging.
2. Touch a message thread to open it.
3. Touch and hold a message and then touch
Forward.
1. From the Media Gallery, touch and hold a picture or
video.
4. Address, edit, and send your message.
2. Touch Share > Messaging.
3. Create and send the message. The selected file is
automatically included as an attachment.
Receiving a Message
When you receive an MMS message, a message
notification appears on the notification bar.
Drafts
To view the message:
Messages you are creating are automatically saved as
drafts when you exit the message screen. The
message must be addressed to someone in order for it
to be saved as a draft.
ᮣ
Drag the notification bar down from the top of the
screen and touch the message notification.
50
This icon
that you have a new message.
appears on the display, reminding you
3. Touch OK to confirm.
To delete message threads:
1. Touch and hold a message thread and then touch
Navigating a Message
As you scroll through a message, numbers, email
addresses, and Web addresses are highlighted.
Delete thread.
2. Touch OK to confirm.
Forwarding
Pictures and audio recordings are also highlighted.
1. Touch a message thread to open it.
Attachments
2. Touch and hold a message and then touch
Forward.
Messages may contain pictures or audio files as
attachments.
3. Address, edit, and send your message.
If a message contains a picture or audio file as an
attachment, touch the attachment to view the picture or
play the audio file.
Embedded objects and attachments are included
when you forward a message.
Calling a Number in a Message
Actions for Received Messages
If any field in a message contains a phone number,
Direct Connect number, or Talkgroup ID, you can call
or send a Call Alert to that number.
Deleting
To delete messages:
To make a call to a number in a message:
1. Touch a message thread to open it.
1. View the message.
2. Touch and hold a message and then touch Delete
message.
51
2. Touch a number and press Talk ` to make a
phone call or press the DC button to make a Direct
Connect call.
2. Touch and hold the message to display the
message options, and then touch Add <item> to
Contacts.
To send a Call Alert to a Direct Connect number in a
message:
3. Touch Create new contact to store the number in a
new entry, or touch an entry to store the
information to an existing entry.
1. View the message.
4. To change the contacts type (Mobile, Home, Work,
etc.), touch the type next to the number or address
and select a type.
2. Touch the Direct Connect number and then press
Menu / > Send Alert.
3. Press the DC button.
5. Scroll to the bottom of the entry and touch Done
To make a Talkgroup call to a Talkgroup ID in a message:
1. View the message.
when you have finished entering the information.
Going to a Website
2. Touch the Talkgroup ID and then press Menu / >
Join Talkgroup.
If a message contains one or more Web addresses,
you can go to the website.
3. Press the DC button.
1. View the message.
Storing Message Information to Contacts
2. Touch the body of the message to display the
Select action screen, and then touch the Web
address. The Web page will open in your browser.
If a message you receive contains a phone number,
Direct Connect number, Talkgroup ID, or an email
address in any of the fields, you can store this
information to Contacts.
Note: The entire Web address must appear in the message.
Otherwise, you cannot go to the website.
1. View the message.
52
Saving Attachments
Caller ID Blocking
1. View a message.
Caller ID allows people to identify a caller before
answering the phone by displaying the number of the
incoming call. If you do not want your number
displayed when you make a call, follow these steps.
2. Touch and hold an attachment and then touch
Copy attached to SD card.
Text Messaging (SMS)
Per-Call Blocking
To block delivery of your number for a single phone call:
With text messaging (SMS), you can receive instant text
messages from another messaging-ready phone or
from an email account.
ᮣ
Touch *67 before dialing the call.
Your phone's SMS address is [email protected].
Your PTN is your ten-digit Personal Telephone Number.
Your Nextel phone number cannot be blocked from
calls made to 911, 800, 855, 866, 877, 888, or other
toll-free phone numbers.
Note: Most traditional phone-to-phone text messages arrive
as MMS messages on your MOTOROLA i1. Your
phone can send and receive MMS messages.
Per-Line Blocking
You can request that Nextel Customer Service
permanently block delivery of your phone number on
every call you make. In this case, you may need to
display your number for certain calls.
Your phone can receive SMS text messages, but it
cannot send them.
Accessing Text Messages
To show your number on a per-call basis:
ᮣ
When you receive a text message, you will see an
alert. Touch Messaging and touch the
message thread to open it.
>
ᮣ
Touch *82 before dialing the call.
53
Call Waiting
Making a Second Call
Call Waiting lets you receive a second call while on an
active call. Call Waiting is always available, unless you
turn it off for a specific call.
1. Place or receive a phone call.
2. While the call is active, press Menu / > Add call.
(The first call is placed on hold.)
If you are on a call and receive a second call, your
phone emits a tone and displays a message.
3. Enter a second phone number and press Talk `
to place the call.
To accept the second call and put the active call on hold:
Note: For quick ways to enter the number, press /.
ᮣ
Press Talk `.
To accept the second call and end the active call:
Press Menu / > End current call & answer.
To decline the second call:
To end the second call and make the on-hold call active:
ᮣ
Press End/Power " and then press Talk `.
ᮣ
To make the on-hold call active and put the active call on
hold:
ᮣ
Press End/Power ". If you subscribe to voicemail,
the call is forwarded to your voicemail box, unless
you set Call Forward or If Busy to a different
number.
ᮣ
Press Menu / > Swap calls.
Turn Off Call Waiting
To turn off Call Waiting before a call:
ᮣ
Touch *70 before dialing the call. Call Waiting
is reactivated once the call ends.
54
forward missed calls to different numbers depending
on the reason you missed the call.
Making a Three-Way Call
With Three-Way Calling, you can talk to two people at
the same time. When using this feature, the normal
airtime rates will be charged for each of the two calls.
Forwarding All Calls
When you set your phone to forward all calls, an icon
appears in the top row of the display:
1. During an active phone call, press Menu / > Add
call. (The first call is placed on hold.)
Phone line 1 is active; calls to phone line 1 are
being forwarded.
2. Enter a second phone number and press Talk `.
Phone line 2 is active; calls to phone line 2 are
being forwarded.
3. Press Menu / > Merge calls.
If one of the people you called hangs up during the
call, you and the remaining caller stay connected. If you
initiated the call and are the first to hang up, all callers
are disconnected.
To forward all calls:
1. Touch
>
Settings > Call settings >
Call forwarding.
2. Touch Always forward.
Call Forwarding
Ⅲ If you specified a forwarding number for this type
of call before, this number displays. To forward all
calls to this number touch Enable.
Call Forwarding lets you forward all your incoming calls
to another phone number – even when your phone is
turned off. You can continue to make calls from your
phone when Call Forwarding is activated.
Ⅲ If no number is specified, touch the number field
to display the dial pad, enter a phone number
and touch Done.
Call Forwarding sends calls to the phone numbers you
specify. You can forward all calls to one number or
– or –
55
Touch the Contacts icon to the right of the
number field and select a number from Contacts.
ⅷ Forward when unanswered — You do not answer on
the first four rings.
ⅷ Forward when unreachable — Your phone is out of
coverage or powered off.
3. Touch Enable and press Home X to return to the
home screen. All your calls are now forwarded to
the number you specified.
Note: You are charged a higher rate for calls you have
forwarded.
Turning Off Call Forwarding
To forward missed calls:
1. Touch
>
Settings > Call settings >
Call forwarding.
1. Touch
>
Settings > Call settings >
Call forwarding.
2. Touch Always forward, Forward when busy, Forward
when unanswered, or Forward when unreachable.
Note: If your phone is set to forward all calls, you must first
disable Always forward to access these options. (See
3. Touch Disable.
All your calls are now sent to your phone.
2. Touch Forward when busy, to specify a forwarding
number for calls received when your phone is
busy.
Forwarding Missed Calls
Calls you miss are forwarded according to the options
set for missed calls. By default, missed calls are
forwarded to voicemail.
3. If you specified a forwarding number for this type
of call before, this number displays.
Ⅲ To forward calls to this number, touch Enable, and
go to step 6.
You can specify a forwarding number for each type of
missed call:
Ⅲ To delete this number, touch the text field, and
ⅷ Forward when busy — Your phone is on a call or
transferring data.
DEL
x
then touch and hold
.
56
4. To enter a forwarding number:
non-emergency incidents. If the situation includes
imminent danger or loss of life, you should dial 911.
Ⅲ Enter the number and touch Done or touch the
Contacts icon to the right to select a number from
Contacts.
Telecommunications Relay Service
Nextel supports services for communicating with
speech and/or hearing impaired individuals. You can
dial 711 to reach a local Telecommunications Relay
Center. You will then be connected to your destination
number. Relay service works through a
Communications Assistant who reads messages typed
into a TDD/TTY device by a speech or hearing
impaired individual to you. The Communications
Assistant then types your spoken messages to the
hearing or speech impaired individual.
5. Touch Enable.
6. Repeat step 2 through step 5 for Forward when
unanswered and Forward when unreachable.
Making International Calls
Your service default is “International Calls Restricted.”
Contact Nextel Customer Service to obtain
international dialing access.
Telecommunications Relay Service is available 24
hours a day, seven days a week, and every call is
strictly confidential.
Calls placed between the United States and Canada
do not require an international access code.
Note: Using 711 to reach Telecommunications Relay Service
Special Dialing Codes
may not be available in all areas.
To enable TTY mode:
Non-Emergency Numbers
Nextel supports many “non-emergency” numbers
(such as #77, 311, and 511) provided by local and state
governments. These numbers are used to report
1. Touch
>
Settings > Call settings >
Additional call settings > TTY.
57
2. Select HCO, TTY, or VCO.
ⅷ Use different ringer styles so that you can tell which
line is receiving a call.
Ⅲ TTY – Type and read text on your TTY device.
ⅷ Forward incoming calls to either your primary or
alternate line phone number.
Ⅲ VCO (Voice Carry-Over) – Speak into the phone
and read text replies on your TTY.
ⅷ Choose a Second Line Service plan that fits your
needs.
Ⅲ HCO (Hearing Carry-Over) – Type text on your
TTY and listen to voice replies on your phone.
In order to activate Second Line Service, contact your
Nextel Sales Representative or call Nextel Customer
Service.
Nextel Phone Services
Contact Nextel Customer Service to obtain these
services or for additional information.
To set the active line (primary or alternate):
1. Press Menu / > Settings > Call settings >
Phone line.
Note: Some services are not available outside of the
continental United States.
2. Select a phone line to be active.
When incoming calls are made to a non-active line,
they will be sent to voicemail without ringing. (See “Call
Second Line Service
You can have two different phone numbers on the
same phone. With Second Line Service, you can:
ⅷ Get separate bills for each phone line.
ⅷ Bring in an existing wireless or home phone number
to Nextel to activate on the second line.
ⅷ Have two different area codes (must be in same
market) to convey a local image to callers.
58
Sprint 411
Dial 411 from your wireless phone to receive
nationwide listings, movie listings and showtimes,
restaurant reservations, and driving directions, as well
as sports scores, stock quotes, and weather conditions.
Spanish speaking operators available. Receive up to
three phone numbers or pieces of information per call,
and be automatically connected at no additional
charge. Airtime and other charges apply.
59
To launch the browser:
Touch
ᮣ
>
Browser.
5. Web and Data Services
Connection
Mobile Network:
Wi-Fi:
ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ Web Address
To go to a URL, touch
Go on the keyboard.
Links
Touch to open.
Drag or flick to scroll.
Image Search
Web Browser
Touch
to open a menu
where you can open your
bookmarks and more.
With Web access on your phone, you can browse your
favorite websites, making it easier than ever to stay
informed while on the go. Follow sports scores,
breaking news, and weather, and shop on your phone
anywhere on the Nextel National Network.
Back
Reload
Forward
Tools
Tabs
Note: If you can’t connect, contact your service provider.
60
Connect
Browser Options
Your phone uses the data capabilities of the Nextel
National Network (over the air) to automatically connect
to the Web. For an even faster Web experience, you
can also set your phone to use available Wi-Fi
setting up and using Wi-Fi connections.)
Touch
Tools to see browser options:
Options
Bookmarks
Add, delete and manage
bookmarks.
History
View and clear your browser’s
history.
Tip: Contact Nextel for information on data usage fees and
your service agreement.
Start Page
Takes you to your browser’s start
page.
Select Web Links
Saved Pages
Downloads
Settings
Save Web pages.
When you touch a link, your
phone outlines it and goes to
that page. If you touch and
hold the link, your phone
shows options, such as Open
in new tab.
View your downloads.
Open your browser’s settings
menu.
Find in Page
Help
Search Web pages for words or
phrases.
Open your browser’s help menu.
61
Going to a Specific Website
Note: Bookmarking a page does not store the page contents,
just its address.
To go to a particular website by entering a Web address
(URL):
Some pages cannot be bookmarked. Whether a
particular Web page may be marked is controlled by its
creator.
1. Touch the text entry field at the top of the page.
If the text entry field is not visible, press Menu / to
bring it up.
Accessing a Bookmark
2. Enter a Web address and then touch Go in the
lower right corner of the keyboard.
1. Touch
Tools > Bookmarks.
2. Touch a bookmark to open the Web page.
Note: Not all websites are viewable on your phone.
Reloading a Web Page
Creating a Bookmark
ᮣ
Touch
Reload at the bottom of the screen.
Bookmarks allow you to store the address of your
favorite websites for easy access at a later time.
(The browser will reload the current Web page.)
1. Go to a Web page and touch
Bookmarks.
Tools >
2. Touch Add (website name).
3. Confirm or edit the bookmark title, choose a folder
to store it in, and then touch Add at the bottom of
the screen.
62
selecting Install, the app will download. After
selecting Buy, you may be asked to sign in to an
additional Google account. Sign in and select
Purchase now to proceed. Follow the onscreen
instructions. To see the download progress, open
the notifications window.
Downloading Apps
Android Market™
ᮣ
Touch
>
Market
The Android Market™ lets you access all the fun games
and cool apps you want. It provides you with access
software developers everywhere, so you can find the
app you want. If you need help or have questions
about Android Market, press Menu / > Help from any
market screen.
After you download an app, the icon for that app
appears on your Applications tab (see “Apps
Manage Apps
1. To manage your apps, from your phone’s home
screen touch
>
Settings > Applications >
Note: You’ll need a Gmail account in order to buy and
download apps from Android Market. (See “Gmail” on
page 64.)
Manage applications.
2. Touch an app to open the details screen — from
here you can review, uninstall, and more.
Browse and Install Apps
Restore Apps
ᮣ
From the Market home page, select a category or
search for an app, touch the app you want to
install, and then touch Install (if the app is free)
or Buy.
ᮣ
To reinstall any downloaded items, touch
>
Market > My Downloads. All previously installed
apps are listed and available for download.
Ⅲ If an app you are downloading requires access to
your data or control of functions on your phone,
you’ll be asked to give your permission. After
63
To control email notifications:
Press Menu / > Settings > Email notifications.
To apply a label to a thread:
Email
ᮣ
Gmail
ᮣ
Touch and hold a message, and then touch
Change labels.
Set up a Gmail Account
If you did not set up a Gmail account when you ran
up now.
POP/IMAP Email
Set Up an Account
ᮣ
Touch
>
Gmail and follow the onscreen
ᮣ
Touch
>
Email.
instructions.
The email setup wizard will guide you through setting
up your email account.
Create a New Email
1. Touch
>
Gmail > Menu / > Compose.
Create a New Email
2. Enter the recipient email address and message,
and then touch Send.
1. Touch
>
Email > Menu / > Compose.
2. Enter the recipient email address and message,
and then touch Send.
Tip: Press Menu / for options, such as Attach or
Add Cc/Bcc.
Tip: Press Menu / for options, such as Attach or Add Cc/
Gmail Features
To search for email:
Bcc.
ᮣ
Press Menu / > Search in a messages list.
64
Google Data Synchronization
Microsoft™ Office Outlook™
Synchronization
The Google apps on your phone give you access to
the same personal information (emails, events, and
contacts) that you have on a computer using Gmail,
Calendar, and Contacts. It’s easy to synchronize the
Google apps information you want to keep up-to-date.
What Can You Manage?
Email, contacts, and calendar on your phone give you
access to the same personal information that you add,
view, and edit on your computer with the use of
Microsoft™ Outlook™.
ᮣ
Touch
>
Settings >
Data synchronization > Google.
You can:
Select Apps to Synchronize
ⅷ View Google™ and Exchange contacts in one list.
ⅷ Schedule and respond to meeting requests.
ⅷ Access your company directory.
1. Touch Background data to enable synchronization.
Tip: To save battery power do not touch Background data.
2. Touch the apps you want to synchronize (Gmail,
Calendar, or Contacts).
Set Up Synchronization
1. Touch
>
Settings >
Data synchronization > Exchange ActiveSync.
2. Enter your user name ([email protected]),
password, email address, and server details
including domain name and security type. (The
server address is the same URL you use to access
65
Wi-Fi®
your company’s email using the Web on your
computer.)
Use a wireless network for fast Internet access and to
download data.
Tip: Contact your business IT department for server details.
3. Touch Next.
Wi-Fi settings
4. Set up your sync options: select email and/or
contacts.
Touch to turn on & scan.
Wi-Fi
5. Touch Save & sync.
Network notification
Notify me when an open network is
available
Note: Set data synchronization to manual to extend battery
Wi-Fi networks
Your network
Touch to connect.
Corporate Calendar
ᮣ
Touch
>
Calendar.
Add Wi-Fi network
Corporate calendar appointments are shown in the
same calendar as your Gmail calendar appointments,
but each will be shown in a different color. Once you
have configured your corporate account, you can start
the calendar app to view, add, and manage your
corporate calendar appointments.
Turn Wi-Fi On or Off
ᮣ
Touch
>
Settings > Wireless controls >
Wi-Fi.
Tip: To extend battery life, turn off Wi-Fi power when not in
use.
Tip: To see the color codes for your calendar press
Menu / > More > My calendars.
66
Wi-Fi Search and Connect
To find networks in your range:
1. Touch
Wi-Fi settings.
>
Settings > Wireless controls >
2. Touch Wi-Fi to turn on and scan. If Wi-Fi is already
on, press Menu / > Scan. Your phone lists the
networks it finds within range.
3. To see your phone’s MAC address or other Wi-Fi
details, press Menu / > Advanced.
4. Touch a network to connect.
5. If necessary, enter Network SSID, Security, and
Wireless password, and touch Connect. When your
phone is connected to a Wi-Fi network, the
wireless indicator
appears in the status bar.
Tip: When you are in range and Wi-Fi is on, you will
automatically reconnect to available networks you’ve
connected to before.
67
Sound Settings
Ringtones
6. Settings
Your phone provides a variety of ringer options that
allow you to customize your ring and volume settings.
These options allow you to identify incoming calls and
messages by the ring.
ࡗ ࡗ ࡗ ࡗ ࡗ Selecting Ringtones
To personalize your ringtones:
1. Touch
>
Settings > Sound & display >
Phone ringtone or Notification ringtone.
Personalize
2. Touch a ringtone to select it, and touch OK to
assign it. (To preview a ringtone, touch it or use the
Navigation Key to scroll through and hear
samples.)
Display Language
You can choose to display your phone’s onscreen
menus in one of several languages.
Assigning a Ringtone to a Contact
You can also assign a ringer to a specific contact entry
so you know who's calling without looking at the
phone.
1. Touch
Select locale.
>
Settings > Locale & text >
2. Touch a language to select it.
1. Touch
Contacts.
68
Silent Mode
Display Settings
The Silent Mode option allows you to mute all sounds
without turning your phone off.
Changing the Screen Timeout
Select how long the display screen remains backlit
after any screen touch or keypress is made.
To activate and deactivate Silent Mode:
ᮣ
Press and hold End/Power " to open the Phone
Options menu and touch Silent mode.
ᮣ
Touch
>
Settings > Sound & display >
Screen timeout and then touch a duration.
Note: Long backlight settings reduce the battery’s talk and
Adjusting the Phone’s Volume Settings
standby times.
Adjust your phone’s volume settings to suit your needs
and your environment.
Changing the Wallpaper
Choose what you see on the display screen while
powering on or off and while on the home screen.
1. Touch
>
Settings > Sound & display.
2. Select Ringer volume or Media volume.
ᮣ
From the home screen, press Menu / >
3. Choose a volume level and touch OK.
Wallpaper > Wallpaper gallery or Media Gallery.
Tip: You can adjust the ringer volume while on the home
screen (or the earpiece volume during a call) by using
the Volume button on the left side of your phone.
To select a wallpaper from the Wallpaper gallery:
1. Flick the thumbnail images left or right to select a
wallpaper.
2. Touch Set wallpaper to assign an image.
70
To select a wallpaper from Media Gallery:
1. Touch Media Gallery.
Messaging Settings
Staying connected to your friends and family has never
been easier. With your phone’s advanced messaging
capabilities, you can send and receive many different
kinds of text messages without placing a voice call.
(For more information see “Multimedia Messages
2. Touch an image to open it.
3. Crop the picture if prompted, and then touch Save
to set the image as your wallpaper.
Tip: You can also set an image as a wallpaper from within
Media Gallery by touching and holding the image
thumbnail and then touching Set as > Wallpaper.
Messaging settings make messaging easier by letting
you decide how you would like to be notified of new
messages, create a signature with each sent message,
and create your own preset messages.
Changing the Clock Display
Select a format for the time and date display.
ᮣ
Touch
>
Settings > Date & time.
Setting Message Notification
Ⅲ Touch Use 24-hour format to toggle between
24-hour time display and 12-hour time display.
When you receive a message, your phone notifies you
by displaying an icon in the notification bar. You can
also choose to be notified with a sound while making a
phone call.
Ⅲ Touch Select date format, and then touch a date
format to assign it.
Note: The time, time zone, and date are set by the network,
and even though they show up as options, they cannot
be changed.
To turn messaging notifications on and off:
ᮣ
Touch
>
Messaging > Menu / >
Settings > Notifications.
71
To select a message notification ringtone:
Touch Messaging > Menu / >
Airplane Mode
ᮣ
>
Settings > Select ringtone, touch a ringtone to
select it, and then touch OK.
Sometimes you may want to have your phone on, but
turn off its ability to make and receive calls and other
transmissions.
To set your phone to vibrate when you receive a message:
Touch Messaging > Menu / >
Settings > Vibrate.
To set your phone so that it cannot make or receive phone
calls, Direct Connect calls, Group Connect calls, Talkgroup
calls, or transfer data:
ᮣ
>
Setting Reports
You can also choose to receive read and delivery
reports for each message you send.
ᮣ
Press and hold End/Power " to open the Phone
Options menu and touch Airplane mode.
When in Airplane Mode,
notifications bar.
appears in your
To receive read reports:
To turn Airplane Mode off:
ᮣ
Touch
>
Messaging > Menu / >
ᮣ
Press and hold End/Power " to open the Phone
Options menu and touch Airplane mode.
Settings > Read reports.
To receive delivery reports:
Touch Messaging > Menu / >
Note: When Airplane Mode is on, your phone’s Bluetooth
capability is disabled, and all active Bluetooth
connections are dropped.
ᮣ
>
Settings > Delivery reports.
72
To access the Direct Connect settings menu:
Touch Settings > Call Settings >
Call Settings
ᮣ
>
Direct Connect settings.
Setting Prepend Dialing
The Prepend feature lets you set a prefix to be added to
the beginning of all dialed numbers, such as a country
code for international calls.
Ⅲ Resume DC — adds 30 seconds to the DC timeout
so Direct Connect calls do not time out quickly
while you are multitasking.
Ⅲ One Touch DC — sets One Touch DC.
1. Touch
>
Settings > Call settings >
Ⅲ Sharing contact info — sets info to share.
Additional call settings.
Ⅲ Talkgroup — lets you silence Talkgroups, define
your Talkgroup area, and manage your Talkgroup
areas.
2. Touch Prepend to activate this feature, and then
touch Prefix number.
Ⅲ DC button light — controls whether or not the
backlight displays when using Direct Connect.
3. Touch the text field to display the keypad, enter a
prefix in the text field (such as +1 for international
calls), and then touch OK.
Setting One Touch DC
Note: This setting does not apply to 911 or Sprint 411.
One Touch DC sets your phone to call the most recent
Direct Connect number or Group on the Call log list, or
a Direct Connect number you choose, every time you
press the DC button. You can also set your phone to
bring up a Direct connect Contacts list when the DC
button is pressed.
Direct Connect Settings
The Direct Connect settings menu controls how your
phone handles Direct Connect calls, Group Connect
calls, and Talkgroup calls.
73
1. Touch
>
Settings > Call settings >
SIM Card Security
Direct Connect settings > One Touch DC.
Important: Except for making emergency calls, your phone
2. Select Off, Launch DC Contact List, DC a selected
contact, or DC the most recent number, and then
touch OK.
does not function without the SIM card.
SIM Card’s PIN
Tip: If you are entering a Talkgroup number, enter # before
You can protect access to your phone by using the SIM
card’s PIN (Personal Identification Number). When you
enable SIM PIN, you must enter the PIN each time you
power up the phone. You can change or disable the
SIM PIN.
the number.
Security Settings
ᮣ
Touch
>
Settings > Security & location.
Lock Your SIM Card
1:22 PM
1. Touch
>
Settings > Security & location >
Security & location
Locate to street-level (requires more
battery plus view of sky)
Set up SIM card lock > Lock SIM card.
Compass
2. Touch the SIM PIN field to display the keyboard,
and then enter your SIM PIN code.
Calibrate Compass
Calibrate the compass for optimum
performance
Security
Important: The default SIM PIN is 0000. Change your PIN to
Security lock
SIM card lock
prevent fraudulent use of the SIM card.
Set up SIM card lock
Passwords
3. Touch OK.
Visible passwords
Show password as you type
74
Entering the PIN
Unblocking the PIN
1. Press and hold End/Power " to turn on your
If you enter your PIN incorrectly three times, your SIM
card is blocked. To unblock your SIM card, you must
contact Nextel Customer Service to get a PIN Unblock
Code (PUK). Follow their instructions for unblocking
your SIM PIN.
phone.
2. When the SIM PIN is locked screen appears, press
Menu /, enter your SIM PIN, and touch OK.
Important: If you enter your PIN incorrectly three times, your
SIM card is blocked. See “Unblocking the PIN” on
page 75.
Important: If you unsuccessfully enter the PUK code ten
times, your SIM card is permanently blocked and
must be replaced. If this happens, you get a
message to contact Nextel Customer Service.
Except for making emergency calls, your phone
does not function with a blocked SIM card.
Changing the PIN
Note: SIM PIN must be turned on in order to access this
feature.
Your Phone’s Lock Feature
1. Touch
>
Settings > Security & location >
Set up SIM card lock > Change SIM PIN.
2. Enter the current SIM PIN and touch OK.
3. Enter the new SIM PIN and touch OK.
Screen Lock
Note: You can make emergency calls on a locked phone
4. Reenter the new SIM PIN to confirm and then
To lock the screen:
touch OK.
ᮣ
Press Screen Lock # on the top of the phone.
Tip: To enter the previous and new SIM PINs, you must first
– or –
touch the SIM PIN field to display the keyboard.
75
Let the screen time out (don’t press or touch
anything).
Unlocking Your Phone
ᮣ
At the “Enter password to unlock” prompt, enter
To unlock the screen:
your password and touch Enter.
Stretch to unlock
ᮣ
Press Screen Lock # and then drag
right.
to the
– or –
At the “Draw pattern to unlock” prompt, draw the
saved pattern to unlock the phone.
Security Lock
Calling in Lock Mode
To access the Security lock menu:
You can place calls to 911 when in lock mode.
ᮣ
Touch
>
Settings > Security & location >
Security lock, and then select an option.
ᮣ
Touch the Emergency call button at the bottom of
Ⅲ To set a password or an unlock pattern that you
need to draw to unlock your screen, touch
Security lock type > Password or Pattern and
follow the prompts to enter and confirm a
password or pattern.
the screen, dial 911, and press Talk `.
Resetting Your Phone
Phone Reset
Ⅲ To turn the lock off, touch Security lock type >
None and enter the password or pattern as
prompted.
Selecting Reset phone resets all phone settings back to
their default values, and clears all information (text
messages, contacts, emails, etc.) and downloaded
apps.
Ⅲ To change the password or lock pattern, touch
Change unlock password or Change unlock
pattern. (To select either of these options, a
security lock type must be set.)
1. Touch
>
Settings > SD card & phone
storage > Master Clear > Reset phone.
76
2. Enter your phone’s six-digit security code and
touch OK. (A disclaimer is displayed.)
Note: Your security code is a six-digit number used for
resetting your phone. Please contact Nextel Customer
Service if you do not know your security code.
3. Read the prompt and touch Erase everything to
complete the reset. (Press Back % to cancel.)
Feature Reset
Selecting Feature Reset resets all phone settings back
to their default settings.
1. Touch
>
Settings > SD card & phone
storage > Feature Reset > Feature Reset.
2. Enter your phone’s six-digit security code and
touch OK. (A disclaimer is displayed.)
Note: Your security code is a six-digit number used for
resetting your phone. Please contact Nextel Customer
Service if you do not know your security code.
3. Read the prompt and touch Re-apply All to
complete the reset. (Press Back % to cancel.)
77
Note: The Call log list records only calls that occur while the
phone is turned on. If a call is received while your
phone is turned off, it will not be included in the phone’s
Call log list.
7. Call Log
If you return a call from the voicemail menu, it will not be
included in your phone’s Call log list.
ࡗ ࡗ ࡗ ࡗ ࡗ Calls and Call Alerts
If the number of a recent call is stored in Contacts, the
following information appears:
ⅷ The name assigned to the number.
ⅷ The Contacts type associated with the number.
About the Call Log
The Direct Connect number Contacts type appears
when you receive a Direct Connect call or Call Alert,
even if the number is not stored in Contacts.
The Call log list displays the numbers (or Contacts
entries) for phone calls and Direct Connect calls you
placed, accepted, or missed, and for Call Alerts you
have received. It also displays My Info and contact
information sent to you from other phones. It is
continually updated as new numbers are added to the
beginning of the list.
Call Alerts you have received appear as Direct Connect
calls. Like all items in the Call log list, they remain listed
until you delete them.
78
For phone calls, an icon appears giving information
about the call.
If you receive My Info from the same phone more than
once, only the most recently sent version appears in
the Call log list.
A call you made.
Contact Information From Other Phones
A call you received.
The Call log list displays contact information sent from
other phones. This information comes from the other
phone’s Contacts list or Call log list. See “Sending My
A missed call. Missed calls appear on the Call log
list only if you have Caller ID.
When you select a call to view its details, you see
information such as the name associated with the call,
the number, date, time, and duration of the call.
This icon
appears with contact information on the
Call log list.
Contact information in the Call log list displays:
My Info From Other Phones
ⅷ The name contained in the contact information.
The Call log list displays My Info sent from other
phones. See “Sending My Info and Contact
ⅷ The Contacts type associated with the number or
address contained in the contact information.
The name or Direct Connect number of the person
who sent the contact information appears as a
separate item on the Call log list, above the information
sent. If one person sends you more than one item of
contact information, all the items appear below the
person’s name or Direct Connect number.
This icon
appears with My Info sent from other
phones, along with the Direct Connect number of the
person who sent the information.
When you select My Info from other phones to view its
details, you see all the information sent.
79
When you select contact information to view its details,
you see the name or Direct Connect number of the
person who sent the information and all the information
in the item.
Saving Items From the Call Log
1. From Call log, touch an entry to open it.
2. Touch Add to contacts.
If you receive contact information with the same name
from the same phone more than once, only the most
recently sent version appears in the Call log list.
Tip: If the item you are storing is a call, Add to contacts does
not appear if the number is already stored in Contacts.
3. Touch Create new contact to store the number in a
new Contacts entry, or touch an entry to store the
number to an existing entry.
Viewing the Call Log
ᮣ
Touch
Dialer > Call log.
Note: Storing My Info or contact information from another
phone to an existing Contacts entry does not change
its name.
Tip: When you’re in the home screen, you can press Talk `
to go to the Call log.
To view the details of an item on the list:
4. If the item is a call, you must assign a Contacts
type to the number.
ᮣ
Touch an entry.
Ⅲ Touch the Contacts type label next to the number
and touch a Contacts type from the list.
5. To add more information to the entry (optional),
follow the applicable instructions in “Creating
6. Scroll to the bottom of the entry and touch Done.
80
Deleting Items From the Call Log
To delete an item from the Call log list:
1. From the Call log, touch an entry to open it.
2. Press Menu / > Delete from call log.
To delete all items on the Call log list:
ᮣ
Touch
Dialer > Call log > Menu / >
Delete all.
Prepending a Number From the
Call Log
If you need to make a call from the Call log list and you
are outside your local area code, you can add the
appropriate prefix by prepending the number.
1. Touch and hold a Call log entry and then touch
Edit number before call > Menu / > Add prefix.
2. Enter the prefix and touch OK to call the number.
81
About Contacts
8. Contacts
Each Contacts entry can store several numbers, email
addresses, chat addresses, or street addresses.
Information stored in Contacts is saved in your phone’s
memory.
ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ Tip: You can import Contacts information from and export it to
your SIM card. See “Import and Export Contacts” on
page 88 for details.
A Contacts entry contains:
ⅷ A name — Typically, this is the name of the person
whose contact information is stored in the entry.
ⅷ A ringtone — You can assign a ringtone to each
entry. This is the sound your phone makes when you
receive phone calls or call alerts from any of the
numbers stored in the entry.
ⅷ A Contacts type — Each number or address stored
must be assigned a Contacts type. (See “Types of
82
Types of Contacts
Each number or address stored must be assigned a
Contacts type:
Creating Contacts Entries
Tip: ICE – In Case of Emergency
To make it easier for emergency personnel to identify
important contacts, you can list your local emergency
contacts under “ICE” in your phone’s Contacts list. For
example, if your mother is your primary emergency
contact, list her as “ICE–Mom” in your Contacts list. To list
more than one emergency contact, use “ICE1–___,”
“ICE2–___,” etc.
Contacts Type
Entry Types
Phone numbers
Home, Mobile, Work, Fax, Work
2, Pager, Other, Custom
DC1, DC2, Custom
Direct Connect
Email addresses
Chat addresses
Home, Work, Other, Custom
A number or address and a Contacts type, or a name
are required for all Contacts entries. Other information
is optional. You may enter the information in any order.
AIM, Windows Live, Yahoo,
Skype, QQ, Google Talk, ICQ,
Jabber
After you have entered the number or address,
Contacts type, and any other optional information,
scroll to the bottom of the entry and touch Done to save
the entry to Contacts.
Postal addresses Home, Work, Other, Custom
Work, Other, Custom
Organizations
To cancel a Contacts entry at any time touch Revert.
To create a Contacts entry:
1. Touch
Contacts > Menu / > New contact.
83
2. To assign a name to the entry, touch the name
Ⅲ To assign a Contacts type for each number or
address (such as Mobile, Home, Work, etc.),
touch the label next to the entry field and touch a
Contacts type to assign it.
field, enter a name and touch Next.
1:22 PM
New contact
4. To add more numbers or addresses to the entry:
First and Last
Ⅲ Touch
to add a new entry field for the type of
contact you are creating (Phone numbers, Direct
Connect, Email addresses, etc.)
Touch + to add another
entry.
Phone numbers
Mobile
Phone number
5. To assign a ringtone to the name (optional):
Ⅲ Touch Ringtone, select a ringtone and then
Touch - to remove this
entry.
Push to Talk
PTT1
touch OK.
PTT number
Touch to display label
options.
6. To assign a picture to the name (optional):
Ⅲ Touch the picture icon to the left of the name field,
touch a picture to select it, crop the picture if
prompted, and then touch Save.
Email addreses
Home Email address
7. Scroll to the bottom of the entry and touch Done.
3. To add a number or address:
Ⅲ Touch the entry field.
Creating Pauses and Waits
When storing a number, you can program your phone
to pause or wait between digits while dialing. A pause
makes your phone pause for three seconds before
Ⅲ Enter the number or address. For phone
numbers, use the ten-digit format. For Direct
Connect numbers, be sure to include the
asterisks (*).
84
dialing further. A wait makes your phone wait for your
response before dialing further.
1:22 PM
This feature is useful when using voicemail or other
automated phone systems that require you to dial a
phone number and then enter an access number.
Dialer
Call log
Contacts
Favorites
All contacts
Search
Touch to search
contacts.
Search contacts
To enter a pause or a wait:
Me
My Info
Your details–always
first in the list.
1. Touch the entry field to bring up the keypad and
begin entering the phone number.
Home
PTT
Ashley Grover
Bomi Kim
2. When you want to insert a pause or a wait, touch
the Symbol Key (&) in the lower left-hand corner
of the keypad.
Contacts List
Touch to view
contact information.
Touch & hold to edit,
delete, and more.
Mobile
PTT 1
Book Club
3 Members
PTT 1
3. Touch Pause or Wait.
Menu Options
Press Menu
create, filter, and
sync contacts.
Note: You can have multiple pauses in a phone number and
Chris Boomer
to
combine waits and pauses.
Viewing Contacts
2. Touch the contact name to display the entry, and
then scroll up or down to view all information
stored for the entry.
1. Touch
Contacts and then either scroll
through the contacts list, or touch Search contacts
and enter a name. (Your phone finds the name
you entered or the nearest match.)
85
Filtering Contacts Entries
You can set Contacts to display only entries with
certain attributes.
Adding a Number to an Entry
1. Touch
Contacts and touch an entry.
2. Press Menu / > Edit contact.
1. Touch
Contacts > Menu / > Filter.
3. Scroll to the contact type for the entry and touch
2. Touch All contacts, Contacts with phone numbers,
Contacts with DC numbers, Phone contacts, Google
All Contacts, or Google My Contacts and then
touch OK.
to create a new entry field.
4. Select an entry type for the new entry, and enter
the number.
5. Scroll to the bottom of the entry and touch Done to
save the new number.
Contacts Action Options
To quickly access these actions for a saved Contact:
Editing Entries
1. Touch
Contacts.
2. Touch and hold a contact to display a quick list of
action items, such as View contact, Call Mobile,
Send text message, Direct Connect, and Share
via DC.
1. Touch
Contacts and touch an entry.
2. Press Menu / > Edit contact.
Contacts Entries” on page 83 to edit the entry.
3. Touch an option to take the corresponding action.
4. Scroll to the bottom of the entry and touch Done
when you have finished making your changes.
86
2. Press Menu / > Edit contact.
Deleting Entries
3. Touch Ringtone.
1. Touch
Contacts and touch an entry.
4. Scroll through available ringtones. (Touch a
ringtone to hear a sample.)
2. Press Menu / > Delete contact.
3. Touch OK to confirm.
5. Touch a ringtone to select it.
6. Touch OK to save the assigned ringer.
7. Scroll to the bottom of the entry and touch Done.
Deleting a Number or Address
1. Touch
Contacts and touch an entry.
2. Press Menu / > Edit contact.
Assigning a Picture to an Entry
3. Scroll to the number or address you want to delete,
Assign a picture to display when you receive a call
from an entry.
and touch
to the right of the item to remove it
4. Scroll to the bottom of the entry and touch Done.
1. Touch
Contacts and touch an entry.
Note: If an entry contains only one number or address,
2. Press Menu / > Edit contact.
deleting the number or address deletes the entry.
3. Touch the picture icon to the left of the name field.
Selecting a Ringtone for an Entry
4. Scroll through available pictures and touch one to
select it.
Assign a ringtone to a Contacts entry so you can
identify the caller by the ringtone. (See “Ringtones” on
Ⅲ If prompted, crop or resize the picture.
5. Touch Save.
6. Scroll to the bottom of the entry and touch Done.
1. Touch
Contacts and touch an entry.
87
Export Contacts to Your SIM Card
Import and Export Contacts
ᮣ
Touch
Contacts > Menu / >
Your phone stores its contact entries in its internal
memory and not within your SIM card. The first time
you use your phone, you will need to import the
contacts from your SIM card to your phone for you to
be able to use the contacts stored on the SIM card.
SIM Manager > Export contacts to SIM.
The contacts stored on your phone will not be saved
on your SIM card unless you export your contacts. It is
recommended that you export your contacts to your
SIM card from time to time to keep your phone and
SIM card in sync.
Note: Your SIM card can store only basic information, such as
phone numbers, Direct Connect numbers, Group
Connect numbers, Talkgroup numbers, and email
addresses.
Import Contacts From Your SIM Card
ᮣ
Touch
Contacts > Menu / >
SIM Manager > Import contacts from SIM card.
88
View your calendar in
different ways: Press
Menu / > Agenda, Day,
Week or Month. When you
highlight an event in the day
and week views, more
details appear.
1:22 PM
January, 2009
Sun Mon Tue Wed Thu Fri Sat
9. Tools
28
4
29
5
30
6
31
7
1
8
2
9
3
ࡗ ࡗ ࡗ ࡗ ࡗ 10
Add Calendar Events
11
18
25
12
19
26
13
20
27
14 15 16 17
21 22 23 24
28 29 30 31
ᮣ
From any calendar
view, press Menu / >
New event. Enter event
details and then scroll
to the bottom of the
entry and touch Save.
Calendar
ᮣ
Touch
>
Calendar
Manage Calendar Events
Tip: You can send calendar events to other people using
ᮣ
To edit an event, touch and hold the event,
touch Edit event, edit the event details, and then
scroll to the bottom of the entry and touch Save.
89
Google Maps™ opens in “Map mode”. To learn more
about the different map modes, see “Select Map
Google Maps™
Note: This feature is not available in all areas. Check with
Nextel for coverage availability.
Set Your Location Sources
ᮣ
To launch the Google Maps tool, touch
>
Set your phone to determine your location using GPS
satellite signals (highly accurate, but uses battery
power) or using the mobile network (less accurate, but
conserves battery power).
Google Maps.
1:22 PM
ᮣ
To set your location source(s), touch
>
Settings > Security & location > Enable GPS
satellites and/or Use wireless networks.
Map View
Drag or flick to scroll.
Find Your Location
Note: Don’t forget to set your location sources.
ᮣ
Touch
>
Google Maps, and then press
Menu / > My Location. Your location shows on
the map as . The bigger the circle, the less
accurate the location.
Press Menu
to open a
menu where you can search,
show your location, change
map modes, get directions,
and more.
Map mode
More
Search
Directions
Find Any Location
My location
Join latitude
1. Press Menu / > Search.
90
2. Enter text in the search box, (for example, an
address, business, or city), and then touch
5. When you have finished, press Menu / > More >
Clear map.
.
Tip: If it is an address you have visited before, select from the
Select Map Mode
list shown.
ᮣ
Touch
>
Google Maps, and then press
3. Touch the search box, in the lower left-hand
corner, to view all the results, and then touch the
one you want. Select Show on map, Get directions,
Street view, Call or Add as a contact.
Menu / > Map mode to select from Map (standard
map view), Satellite (map with photos), or Traffic
(map with traffic conditions).
Ⅲ Press Menu / > More > Clear Map to clear your
selections.
Get Directions
1. Touch
>
Google Maps, and then press
Latitude
Menu / > Directions.
Note: This feature is not available in all areas. Check with your
2. Enter a starting point address, or touch
and
service provider.
select My current location, Contacts, or Points on
map.
Join Latitude
3. Enter an end point address, or touch
and select
See where your friends and family are on Google
Maps™. Plan to meet up, check that your parents got
home safely, or just stay in touch.
Contacts or Points on map.
4. Select your mode of transport (car, public transport
or walk), then touch Go. Your directions are shown
as a list. To view your directions on a map, press
Menu / > Show on map.
Don’t worry, your location is not shared unless you
agree to it. You need to join Latitude, and then invite
your friends to view your location or accept their
invitations.
91
To join Latitude:
Touch
Share Location
ᮣ
>
Google Maps > Menu / > Join
When you receive a request to share location details
you can choose to:
Latitude. Read the privacy policy and if you agree
with it, touch Allow & Share.
ⅷ Accept and share back — see your friend’s location,
and your friend can see yours.
Add and Remove Friends
To add friends:
ⅷ Accept, but hide my location — see your friend's
location, but they can't see yours.
1. Touch
>
Google Maps > Menu / >
ⅷ Don't accept — location information is not shared
between you and your friend.
Latitude > / > Add friends.
2. Touch Select from Contacts or Add via email
address, touch a contact, and then touch Add
friends.
Hide Your Location
ᮣ
Touch
>
Google Maps > Menu / >
Latitude to show your friends list. Touch your
contact name, and then press Menu / > Privacy >
Hide your location.
If your friends already use Latitude, they’ll receive an
email request and a notification. If they have not yet
joined Latitude, they’ll receive an email request that
invites them to sign in to Latitude with their Google
account.
Turn Latitude Off
1. Touch
>
Google Maps > Menu / >
To remove friends:
Latitude to show your friends list, and then press
Menu / > Privacy > Turn off Latitude.
1. Touch
>
Google Maps > Menu / >
Latitude to show your friends list, and then touch a
2. Touch Yes to confirm.
friend in your list.
2. Touch Remove.
92
From the Google Talk screen, press Menu / and
select an option to send invitations, add new friends,
and more.
Google Talk™
Google Talk instant messaging lets you chat with other
Google Talk users on phones or on the web.
Instant Messages
To send and receive instant messages, you can use an
instant messaging app (such as Google Talk™) or your
browser.
ᮣ
Touch
>
Google Talk.
Touch to change your
online status message.
ⅷ To download and use an instant messaging app,
touch
>
Market > Applications >
Communication, and then choose an app for your
provider. Once you download the app, you’ll see it on
your Applications tab. (See “Apps (Applications)” on
page 15.)
Touch to
change your
picture.
Touch to change
your status.
Opened chats.
Touch a callout
to open the chat
screen and start
chatting with
ⅷ If you don’t see an app for your IM provider, you can
Friends list
use your Web browser. Touch
>
Browser,
your friend.
and then enter your provider’s Web address and
touch Go. Once you’re there, follow the link to sign in.
Your IM options will depend on your IM provider.
Online
status:
Available
Idle
Busy
Offline
93
Alarm clock
ᮣ
Touch
>
Alarm Clock.
Alarm Clock
Ⅲ To turn on an alarm, touch
the check box.
Ⅲ When an alarm sounds,
touch Dismiss to turn it off
or Snooze to delay.
1:00
PM
PM
Ⅲ To add an alarm, press
Menu / > Add alarm, and
then enter alarm details.
every day
3:30
Tue
4:00
PM
Mon, Fri
Ⅲ To enable or disable an
alarm, touch the check box.
Calculator
ᮣ
Touch
>
Calculator.
Your calculator has basic and advanced views. To
change views, press Menu / > Advanced panel or
Basic panel. To clear history, press Menu / > Clear
history.
94
Inserting the microSD Card
Note: The memory card provided with your phone contains
useful preloaded information, including guided tours of
some of your phone’s features. You may insert another
compatible memory card at any time; however, any
information preloaded on the provided memory card
will not be available.
10. microSD Card
ࡗ ࡗ ࡗ 2. Open the memory card slot cover, and slide in the
memory card until it clicks into place.
Using a microSD Card With Your
Phone
Using the microSD Card Slot
Your phone is equipped with a microSD (Secure
Digital) memory card slot to expand the phone’s
available memory space. It allows you to store images,
videos, music, and voice data in your phone.
Note: You need the memory card installed for some features
on your phone, such as Camera.
95
To insert the microSD card into the microSD adapter:
Formatting Your Memory Card
ᮣ
With the label side of the microSD card facing up,
insert the card into the supplied microSD adapter,
and gently slide the card until it is fully inserted.
If you are having difficulty with a memory card, you may
format the card using your phone. This process
removes any data on the card and sets up a new folder
system.
1. Before you format your memory card you need to
unmount it. Touch
>
Settings >
SD card & phone storage > Unmount SD card.
2. Touch
>
Settings >
SD card & phone storage > Format SD card.
To remove the microSD card from the microSD adapter:
WARNING: The formatting procedure erases all the data on
the microSD card, after which the files CANNOT
be retrieved. To prevent the loss of important data,
please check the contents before you format the
card.
ᮣ
Hold the front edge of the microSD card, and
gently pull outward to remove it from the adapter.
Tip: If your computer has an SD card slot or if you have an SD
card adapter, you can use the microSD card and adapter
to transfer files such as audio files, pictures, and videos
directly between your computer and your microSD card.
Using the microSD Adapter
The supplied microSD adapter allows microSD cards
to be used in SD-compatible devices such as digital
cameras, printers, and computers. Before using, you
will need to insert the microSD card into the microSD
adapter.
When you insert the card into your computer, select
Open folder to view files using Windows Explorer (or a
similar option) and drag and drop files using the available
folders.
97
home screen, connect a Motorola micro USB data
cable from your phone’s micro USB port to a USB
port on your computer. Your phone should show
in the notifications bar.
microSD Settings
Viewing Memory in the microSD Card
Note: You may need to remove the USB data cable from the
1. With the microSD card inserted, touch
>
charger power head.
Settings > SD card & phone storage.
2. The following information will be displayed:
Ⅲ Total space displays the capacity of the memory
Note: Make sure to connect the phone to a high power USB
port. Typically, these are located directly on your
computer.
card.
Ⅲ Available space displays the amount of free
memory space.
Note: Your phone supports Microsoft™ Windows™ XP and
Windows Vista™. Other operating systems may not be
compatible.
USB and Memory Card
2. Your phone shows
can’t use the files on your memory card while it is
connected.
in the notifications bar. You
USB Drag and Drop
3. Touch Mount (if asked) to connect your memory
card.
You can transfer your pictures,
videos, music, ringtones, and
more, from your computer to your
phone’s memory card.
Note: If you connect a mass storage device to a peripheral
device, your device may not work properly.
1. With a memory card inserted,
and your phone showing the
4. On your computer, use the “My Computer” window
to find “Removable Disk”.
98
5. Click on the “Removable Disk” icon to access the
memory card.
6. Drag and drop your pictures, videos, music,
ringtones, and more, to your phone folder. To help
manage your files, you can create more folders in
your phone folder.
7. When you’re done, use your computer’s “Safely
Remove Hardware” feature to finish.
99
Ⅲ Touch Gallery on the right to view the picture you
have just taken.
11. Camera
● To set the photo as a wallpaper or contact
photo, touch and hold the thumbnail and then
touch Set as > Contact icon or Wallpaper.
● To send the photo in a message or post it
online, touch and hold the thumbnail and then
select a sharing option. For more info on
sharing your photos, see “Share Your Photo
ࡗ ࡗ Taking Pictures
● To delete the photo, touch and hold the
thumbnail and then touch Delete.
Taking pictures with your phone’s built-in camera is as
simple as choosing a subject, pointing the lens, and
pressing a button.
● For more options, press Menu / > More.
To take a picture:
1. Press Camera j on the right side of the phone to
launch the camera.
2. Aim the camera lens at your subject and press
Camera j to take a picture.
Ⅲ To focus the picture, press Camera j half way
until the auto focus box turns green. To take the
photo, press Camera j down all the way.
100
Photo Options
In the viewfinder, press Menu / > Settings to open the
Scenes
Match
lighting.
3652
Scenes
Effects
camera menu:
Effects
Add
effects.
Options
Picture
Resolution
Set the photo resolution.
Flash
Turn on
and off.
Flash
Video
Resolution
Set the camcorder video
resolution.
Gallery
Go to the
Media
Gallery
Quick Send
Address
Store email addresses for sending
pictures and videos.
Autofocus Box
Turns green when
Picture Counter
Settings
Gallery.
picture is in focus.
Review Time
Choose the amount of time a
recently taken picture is displayed
on the view screen.
Tip: Photos are stored on your microSD memory card.
Picture Resolution is 5MP, unless you change it.
101
Manage Your Photos
View Your Photos
1. Touch
>
Media Gallery > All Pictures.
1:22 PM
ᮣ
Touch
Gallery > All Pictures.
>
Media
All Pictures
Today
2. Touch and hold a photo, then:
Ⅲ To delete the photo, touch Delete.
Play a Slideshow
Ⅲ To set the photo as a contact picture or wallpaper,
touch Set as.
ᮣ
Touch
>
Media
Gallery > All Pictures >
Menu / > Play Slideshow to
start a slideshow. To stop the
slideshow, touch the display.
To return to the gallery, press
Back %.
Edit Your Photos
1. Touch
>
Media Gallery > All Pictures.
Share Your Photo Gallery
2. Touch and hold a picture, and then touch Edit >
One-click optimize, Rotate, Crop, Effects, Brightness
& contrast, Color & saturation, Flip, and Resize.
To send your photo in a message, Direct Connect call, or
post it online:
Using the Zoom
To adjust the zoom:
1. Touch
>
Media Gallery > All Pictures.
2. Touch and hold a photo, and then touch Share.
3. Choose how you want to share: DC (Direct
Connect), Email, Gmail, Messaging, Picasa, or
Quick Send.
ᮣ
While in the viewfinder, press the Navigation Key
down to zoom in, or press up to zoom out.
102
After you have finished recording your video, touch the
screen, when prompted:
Videos
ⅷ To send the video in a message or post it online,
touch Share. For more info on sharing your videos,
Record and Share Videos
1. Press Camera j > Menu / > Camcorder.
ⅷ To play the video, touch
.
2. To record the video, press Camera j. To stop the
video recording, press Camera j again.
ⅷ To delete the video, touch Delete.
Scenes
Match
lighting.
22:59:02
Scenes
Effects
Add
effects.
Effects
Light
Light
Turn on
and off.
Gallery
Go to the
Media
Gallery
Gallery.
Timer
Settings
Tip: To send your video in a message, set the video quality to
Small(QCIF) by pressing / > Settings > Video
Resolution.
103
ᮣ
Touch
>
Settings > Wireless controls >
Bluetooth settings.
12. Bluetooth® Wireless
Bluetooth settings
Touch to turn on & scan.
Bluetooth
ࡗ ࡗ Device name
(#########) 38.4 MHz Class 1.5
Discoverable
Make device discoverable
Touch to re-scan.
Touch to connect.
Scan for devices
Turning Bluetooth Power
On and Off
Bluetooth devices
(found device name)
Pair with this device
Bluetooth is a short-range communications technology
that allows you to connect wirelessly to a number of
Bluetooth devices, such as headsets and hands-free
car kits, and Bluetooth-enabled handhelds, computers,
printers, and wireless phones. The Bluetooth
communication range is usually up to approximately
30 feet. By default, your device’s Bluetooth feature is
turned off.
Note: To extend battery life, turn Bluetooth power off when not
in use.
105
Bluetooth Status Indicators
1. Make sure the device you are pairing with is in
discoverable mode.
The Bluetooth status indicators on your phone’s display
screen shows your Bluetooth connection status at a
glance:
Tip: Refer to the guide that came with the device for details.
2. Touch
>
Settings > Wireless controls >
None – Bluetooth is disabled (default status).
Bluetooth settings.
– Status indicator will be light blue when Bluetooth
is turned on, but no device is connected.
3. Touch Bluetooth to turn on and scan. If Bluetooth is
already on, touch Scan for devices.
– Status indicator will turn blue when connected to a
Bluetooth device.
4. Touch a device to connect.
5. If necessary, touch OK, or enter the device passkey
(for example 0000) to connect to the device. When
the device is connected, the Bluetooth connected
Connecting and Disconnecting
Bluetooth Devices
indicator
appears in the notifications bar.
Note: Using a mobile device or accessory while driving may
cause distraction and may be illegal. Always obey the
laws and drive safely.
Connect New Devices
Note: This feature requires an optional accessory.
To connect with a new device, you need to pair with it.
You only need to do this once for each device; to
connect again, see “Reconnect Devices” on page 107.
106
Reconnect Devices
To automatically reconnect your phone with a paired
device, simply turn on the device.
To manually reconnect your phone with a paired
device, touch the device name in the Bluetooth devices
list.
Disconnect Devices
To automatically disconnect your phone from a paired
device, simply turn off the device.
To manually disconnect your phone from a paired
device, touch the device name in the devices list, and
then touch OK.
Edit Properties
To edit your MOTOROLA i1’s device name, touch
>
Settings > Wireless controls > Bluetooth
settings > Device name. Enter a name and touch OK.
107
Music Basics
13. Music
ᮣ
Touch
>
Music, touch a category, and
then touch a song to begin playing it.
Music
ࡗ ࡗ ࡗ ࡗ Artists
Songs
Albums
Playlists
Music Artist
Album Title
Song Title
1:14
3:45
Categories
Music Controls
Touch a category, and
then touch a song or
playlist.
Tip: When a song is playing, you can add it to a playlist by
pressing / > Add to playlist.
108
What Music File Formats Can I Play?
Your phone can play many types of files: AMR-NB/WB,
MP3, PCM/WAV, AAC, AAC+, eAAC+, MIDI, OGG, and
WMA.
Set Up Music
What Music Transfer Tools Do I Need?
To put music on your computer and then load it on
your phone, you need:
ⅷ A Microsoft® Windows® PC.
Note: Your phone does not support any DRM protected files.
What Headphones Can I Use?
ⅷ A USB data cable (included).
Your phone has a 2.5mm headset jack for wired stereo
listening. You can go wireless with Bluetooth® stereo
headphones or speakers (see “12. Bluetooth®
You Need a Memory Card
Your music is stored on your memory card. Your phone
supports removable microSD memory cards up to
32 GB capacity. To make sure your memory card is
Get Music
Transfer Music Using USB
Tip: To see the available memory on your memory card,
Transfer music files from a computer to your memory
card.
touch
>
Settings > SD card & phone
storage.
1. With a memory card inserted, and your phone
showing the home screen, connect the Motorola
micro USB data cable from your phone’s micro
109
USB port to a USB port on your computer. Your
phone should show in the status bar.
Play Music
Note: Make sure to connect the phone to a high power USB
port. Typically, these are located directly on your
computer.
Music Library
Open your music library, then select what you want to
play.
Note: Your phone supports Microsoft™ Windows™ XP and
Windows Vista™. Other operating systems may not be
compatible.
ᮣ
Touch
>
Music.
Music
2. Your phone shows
in the notifications bar. You
can’t use the files on your memory card while it is
connected.
3. Touch Mount (if asked) to connect your memory
Artists
Songs
Albums
card.
Categories
Touch to list songs or
playlists.
4. Find “Removable Device” (your memory card) in
the “My Computer” window.
5. Drag and drop your music to a folder on your
memory card.
Playlists
6. To help manage your music, create a “Music”
folder on your memory card.
Music Artist
Song Title
Last Played
Touch to play again.
7. When you’re done, use your computer’s “Safely
Remove Hardware” feature to finish.
110
Your music is stored by artists, albums, songs, and
playlists. Touch a category, then touch the song or
playlist you want to play. Press Menu / > Party shuffle
to randomly play all your songs.
Music Player Controls
Play/Pause
Touch
Touch
/
/
.
.
Previous/Next
Fast Forward/Rewind
View Playlist
Shuffle
Touch & hold
/
.
Music Player Functions
Just touch a song or playlist to get going.
Touch
Touch
Touch
.
.
.
Open Playlist
Repeat
Volume
Press the side Volume
button.
Shuffle On/Off
View Library
Press / > Library.
Repeat Off/All
/Current
Turn Shuffle On/Off
Add to Playlist
Use as Ringtone
Delete
Press / > Party shuffle.
Press / > Add to playlist.
Press / > Use as ringtone.
Press / > Delete.
Music Artist
Album Title
Song Title
Artist
Album
Song Title
Music Controls
1:14
3:45
Total Song Time
Progress Bar
111
Hide, Wake, Turn Off
Press Home X to use another app. Your music
continues to play.
When you see
in the status bar a song is playing,
flick down to see details. Touch the song to return to
the music controls.
To turn off your music, touch
.
Playlists
To add a song from the music library to a playlist, touch
and hold the song then touch Add to playlist. Choose
an existing playlist, or touch New to create a new
playlist.
To add a song to the playlist you’re playing, press
Menu / > Add to playlist in the music player.
To edit, delete, and rename playlists, touch and hold
the playlist in the music library.
112
Safety and Warranty
Information
Failure to read and follow the information provided in this
phone guide may result in serious bodily injury, death, or
property damage.
S1. Important Safety
Information
General Precautions
There are several simple guidelines to operating your phone
properly and maintaining safe, satisfactory service.
ࡗ ࡗ ⅷ To maximize performance, do not touch the bottom portion
of your phone where the internal antenna is located while
using the phone.
ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ࡗ ⅷ Speak directly into the mouthpiece.
ⅷ Your mobile device is designed to resist damage from
exposure to certain rugged conditions. Avoid prolonged or
extreme exposure to those conditions.
ⅷ Any changes or modifications to your phone not expressly
approved in this document could void your warranty for this
equipment and void your authority to operate this
equipment.
Note: For the best care of your phone, only authorized personnel
should service your phone and accessories. Failure to do
so may be dangerous and void your warranty.
114
Following Safety Guidelines
Maintaining Safe Use of and Access
to Your Phone
To operate your phone safely and efficiently, always follow any
special regulations in a given area. Turn your phone off in areas
where use is forbidden or when it may cause interference or
danger.
Do Not Rely on Your Phone for Emergency Calls
Mobile phones operate using radio signals, which cannot
guarantee connection in all conditions. Therefore you should
never rely solely upon any mobile phone for essential
communication (e.g., medical emergencies). Emergency calls
may not be possible on all cellular networks or when certain
network services or mobile phone features are in use. Check
with your local service provider for details.
Using Your Phone Near Other Electronic Devices
Most modern electronic equipment is shielded from radio
frequency (RF) signals. However, RF signals from wireless
phones may affect inadequately shielded electronic
equipment.
RF signals may affect improperly installed or inadequately
shielded electronic operating systems or entertainment
systems in motor vehicles. Check with the manufacturer or their
representative to determine if these systems are adequately
shielded from external RF signals. Also check with the
manufacturer regarding any equipment that has been added to
your vehicle.
Using Your Phone While Driving
Talking on your phone while driving (or operating the phone
without a hands-free device) is prohibited in some jurisdictions.
Laws vary as to specific restrictions. Remember that safety
always comes first.
Consult the manufacturer of any personal medical devices,
such as pacemakers and hearing aids, to determine if they are
adequately shielded from external RF signals.
Responsible driving practices can be found in “Smart Practices
While Driving” on page 131 and/or at the Motorola website:
www.motorola.com/callsmart.
Tip: Purchase an optional hands-free accessory at your local
Sprint Store, or call Nextel at 1-866-866-7509.
115
When using your radio product as a traditional
two-way radio, hold the radio product in a
vertical position with the microphone one to
two inches (2.5 to 5 cm) away from the lips.
Operational Precautions
Note: Always turn off the phone in healthcare facilities, and
request permission before using the phone near medical
equipment.
If you wear a radio product on your body when
transmitting, always place the radio product in
To assure optimal radio product performance and to be sure
that human exposure to RF does not exceed the guidelines set
forth in the relevant standards, always follow these instructions
and precautions:
a Motorola approved clip, holder, holster, case or body harness.
If you do not use a body-worn accessory supplied or approved
by Motorola and are not using the radio product in the intended
use positions along side the head in the phone mode or in
front of the face in the two-way radio mode, or if you hang your
device from a lanyard around your neck, keep the device at
least 2.5 centimeters (1 inch) from your body when transmitting.
Phone Operation
When placing or receiving a phone call, hold your radio
product as you would a wireline telephone. Speak directly into
the microphone.
Approved Accessories
Two-way Radio Operation
For a list of approved Motorola accessories call 1-800-453-0920,
or visit our website at www.motorola.com/phoneaccessories.
Your radio product has been designed and tested to comply
with national and international standards and guidelines
regarding human exposure to RF electromagnetic energy,
when operated in the two-way mode (at the face, or at the
abdomen when using an audio accessory) at usage factors of
up to 50% talk/50% listen.
Turning Off Your Phone Before Flying
Turn off your phone before boarding any aircraft. To prevent
possible interference with aircraft systems, the U.S. Federal
Aviation Administration (FAA) regulations require you to have
permission from a crew member to use your phone while
the plane is on the ground. To prevent any risk of interference,
FCC regulations prohibit using your phone while the plane is in
the air.
Transmit no more than the rated duty factor of 50% of the time.
To transmit (talk), push the PTT button. To receive calls, release
the PTT button. Transmitting 50% of the time or less, is
important because this radio generates measurable RF energy
only when transmitting (in terms of measuring for standards
compliance).
116
ⅷ A choking hazard may exist for small, detachable parts.
Turning Off Your Phone in Dangerous Areas
ⅷ Improper use could result in loud sounds, possibly causing
hearing injury.
To avoid interfering with blasting operations, turn your phone
off when in a blasting area or in other areas with signs
indicating two-way radios should be turned off. Construction
crews often use remote-control RF devices to set off explosives.
ⅷ Improperly handled batteries could overheat and cause a
burn.
Do not allow children to play with your phone as they could
hurt themselves and others, damage the phone or make calls
that increase your invoice.
Turn your phone off when you’re in any area that has a
potentially explosive atmosphere. Although it’s rare, your phone
and accessories could generate sparks. Sparks can cause an
explosion or fire, resulting in bodily injury or even death. These
areas are often, but not always, clearly marked. They include:
Glass Parts
Some parts of your phone may be made of glass. This glass
could break if the product is dropped on a hard surface or
receives a substantial impact. If glass breaks, do not touch or
attempt to remove. Stop using your phone until the glass is
replaced by a qualified service center.
Ⅲ Fueling areas such as gas stations.
Ⅲ Below deck on boats.
Ⅲ Fuel or chemical transfer or storage facilities.
Ⅲ Areas where the air contains chemicals or particles such
as grain, dust, or metal powders.
Seizures/Blackouts
Ⅲ Any other area where you would normally be advised to
turn off your vehicle’s engine.
Some people may be susceptible to epileptic seizures or
blackouts when exposed to flashing lights, such as when
playing video games. These may occur even if a person has
never had a previous seizure or blackout.
Note: Never transport or store flammable gas, flammable liquids,
or explosives in the compartment of your vehicle that
contains your phone or accessories.
If you have experienced seizures or blackouts, or if you have a
family history of such occurrences, please consult with your
physician before playing video games or enabling a flashing-
lights feature (if available) on your phone.
Keep Your Mobile Device and Its Accessories Away
From Small Children
These products are not toys and may be hazardous to children.
For example:
Discontinue use and consult a physician if any of the following
symptoms occur: convulsion, eye or muscle twitching, loss of
117
awareness, involuntary movements, or disorientation. It is
always a good idea to hold the screen away from your eyes,
leave the lights on in the room, take a 15-minute break every
hour, and stop use if you are very tired.
Repetitive Motion
When you repetitively perform actions such as pressing keys or
entering finger-written characters, you may experience
occasional discomfort in your hands, arms, shoulders, neck, or
other parts of your body. If you continue to have discomfort
during or after such use, stop use and see a physician.
Caution About High Volume Usage
Battery Use and Safety
WARNING: Exposure to loud noise from any source for extended
periods of time may affect your hearing. The louder
the volume sound level, the less time is required
before your hearing could be affected.
Important: HANDLE AND STORE BATTERIES PROPERLY TO
AVOID INJURY OR DAMAGE. Most battery issues
arise from improper handling of batteries, and
particularly from the continued use of damaged
batteries.
To protect your hearing:
ⅷ Limit the amount of time you use headsets or headphones at
high volume.
ⅷ Avoid turning up the volume to block out noisy surroundings.
DON’Ts
ⅷ Turn the volume down if you can’t hear people speaking
near you.
ⅷ Don’t disassemble, crush, puncture, shred, or otherwise
attempt to change the form of your battery.
If you experience hearing discomfort, including the sensation of
pressure or fullness in your ears, ringing in your ears, or
muffled speech, you should stop listening to the device through
your headset or headphones and have your hearing checked.
ⅷ Don’t let the phone or battery come in contact with water.
Water can get into the phone’s circuits, leading to corrosion.
If the phone and/or battery get wet, have them checked by
your carrier or contact Motorola, even if they appear to be
working properly.
For more information about hearing, see our website at
direct.motorola.com/hellomoto/nss/AcousticSafety.asp (in English
only).
ⅷ Don’t allow the battery to touch metal objects. If metal
objects, such as jewelry, stay in prolonged contact with the
battery contact points, the battery could become very hot.
118
ⅷ Don’t place your battery near a heat source. Excessive heat
can damage the phone or the battery. High temperatures
can cause the battery to swell, leak, or malfunction.
Therefore:
display such as Invalid Battery or Unable to Charge, take the
following steps:
ⅷ Remove the battery and inspect it to confirm that it has a
“Motorola Original” hologram;
Ⅲ Do not dry a wet or damp battery with an appliance or
heat source, such as a hair dryer or microwave oven.
ⅷ If there is no hologram, the battery is not a Motorola battery;
ⅷ If there is a hologram, replace the battery and retry charging
it;
Ⅲ Avoid leaving your phone in your car in high
temperatures.
ⅷ If the message remains, contact a Motorola Authorized
Service Center.
DOs
Important: Motorola’s warranty does not cover damage to the
phone caused by non-Motorola batteries and/or
chargers.
ⅷ Do avoid dropping the battery or phone. Dropping these
items, especially on a hard surface, can potentially cause
damage.
ⅷ Do contact your service provider or Motorola if your phone
or battery has been damaged from dropping or high
temperatures.
WARNING: Use of a non-Motorola battery or charger may
present a risk of fire, explosion, leakage, or other
hazard.
Important: USE MOTOROLA ORIGINAL PRODUCTS FOR
QUALITY ASSURANCE AND SAFEGUARDS. To aid
consumers in identifying authentic Motorola batteries
from non-original or counterfeit batteries (that may not
have adequate safety protection), Motorola provides
holograms on its batteries. Consumers should
confirm that any battery they purchase has a
Proper and Safe Battery Disposal and Recycling
Proper battery disposal is not only important for safety, it
benefits the environment. Consumers may recycle their used
batteries in many retail or service provider locations. Additional
information on proper disposal and recycling may be found on
the Web:
“Motorola Original” hologram.
ⅷ
www.motorola.com/recycling
Motorola recommends you always use Motorola-branded
batteries and chargers. Motorola mobile devices are designed
to work with Motorola batteries. If you see a message on your
ⅷ
www.rbrc.org/call2recycle/ (in English only)
119
Disposal of Lithium Ion (LiIon) Batteries: Promptly
dispose of used batteries in accordance with local
regulations. Contact your local recycling center or
national recycling organizations for more information
on how to dispose of batteries.
manufacturer, or call 1-866-866-7509 to order. They’re also
available at www.nextel.com — click Accessories. Buying the
right batteries and accessories is the best way to ensure
they’re genuine and safe.
ⅷ In order to avoid damage, charge the battery only in
temperatures that range from 32° F to 113° F (0° C to 45° C).
Do not handle a damaged or leaking Li-Ion battery as you can
be burned.
ⅷ Don’t use the battery charger in direct sunlight or in high
humidity areas, such as the bathroom.
WARNING: Never dispose of batteries in a fire because they may
ⅷ Never dispose of the battery by incineration.
explode.
ⅷ Keep the metal contacts on top of the battery clean.
ⅷ Don’t attempt to disassemble or short-circuit the battery.
Special Note: Be sure to dispose of your battery properly. In
some areas, the disposal of batteries in household or business
trash may be prohibited.
ⅷ The battery may need recharging if it has not been used for
a long period of time.
Protecting Your Battery
The guidelines listed below help you get the most out of your
battery’s performance.
ⅷ It’s best to replace the battery when it no longer provides
acceptable performance. It can be recharged hundreds of
times before it needs replacing.
ⅷ Don’t store the battery in high temperature areas for long
periods of time. It’s best to follow these storage rules:
ⅷ Recently there have been some public reports of wireless
phone batteries overheating, catching fire, or exploding. It
appears that many, if not all, of these reports involve
counterfeit or inexpensive, aftermarket-brand batteries with
unknown or questionable manufacturing standards. Nextel is
not aware of similar problems with Nextel phones resulting
from the proper use of batteries and accessories approved
by Nextel or the manufacturer of your phone. Use only
Nextel-approved or manufacturer-approved batteries and
accessories found at Sprint Stores or through your phone’s
Less than one month:
-4° F to 140° F (-20° C to 60° C)
More than one month:
-4° F to 113° F (-20° C to 45° C)
120
Batteries and Chargers
Your battery, charger, or portable radio may contain symbols,
defined as follows:
Using Your Phone With a Hearing
Aid Device
A number of Nextel phones have been tested for hearing aid
device compatibility. When some wireless phones are used
with certain hearing devices (including hearing aids and
cochlear implants), users may detect a noise which can
interfere with the effectiveness of the hearing device.
Symbol
Definition
032374o
Important safety information
follows.
Do not dispose of your battery or
phone in a fire.
Some hearing devices are more immune than others to this
interference noise, and phones also vary in the amount of
interference noise they may generate. ANSI standard C63.19
was developed to provide a standardized means of measuring
both wireless phone and hearing devices to determine usability
rating categories for both.
Your battery or phone may require
recycling in accordance with local
laws. Contact your local regulatory
authorities for more information.
032375o
Ratings have been developed for mobile phones to assist
hearing device users find phones that may be compatible with
their hearing device. Not all phones have been rated for
compatibility with hearing devices. Phones that have been
rated have a label with the rating(s) located on the box, and are
listed at www.motorola.com/accessibility.
Do not throw your battery or
phone in the trash.
Your phone contains an internal
lithium ion battery.
Li Ion BATT
032378o
These ratings are not guarantees. Results will vary depending
on the user’s hearing device and individual type and degree of
hearing loss. If a hearing device is particularly vulnerable to
interference noise; even a phone with a higher rating may still
cause unacceptable noise levels in the hearing device. Trying
Do not let your battery, charger, or
phone get wet.
Listening at full volume to music
or voice through a headset may
damage your hearing.
121
out the phone with your hearing device is the best way to
evaluate it for your personal needs.
find the one that works best with your hearing aid device.
Should you experience interference or find the quality of
service unsatisfactory after purchasing your phone, promptly
return it to the store within 30 days of purchase. With the Sprint
30-day Risk-Free Guarantee, you may return the phone within
30 days of purchase for a full refund. More information about
hearing aid compatibility may be found at:
M-Ratings: Phones rated M3 or M4 meet FCC requirements
for hearing aid compatibility and are likely to generate less
interference to hearing devices than unrated phones. (M4 is the
better/higher of the two ratings.)
T-Ratings: Phones rated T3 or T4 meet FCC requirements and
are likely to be more usable with a hearing device’s telecoil (“T
Switch”or “Telephone Switch”) than unrated phones. (T4 is the
better/higher of the two ratings. Note that not all hearing
devices have telecoils in them.)
www.motorola.com/accessibility, www.fcc.gov, www.fda.gov, and
www.accesswireless.org.
Getting the Best Hearing Device Experience With
Your Phone
Hearing aid devices may also be measured for immunity to
interference noise from wireless phones and should have
ratings similar to phones. Ask your hearing health care
professional for the rating of your hearing aid. Add the rating of
your hearing aid and your phone to determine probable
usability:
To further minimize interference:
ⅷ Set the phone’s display and keypad backlight settings to
ensure the minimum time interval:
1. Press / > Settings > Sound & display >
Screen timeout.
ⅷ Any combined rating equal to or greater than six offers
excellent use.
2. Touch the minimum time interval (15 seconds).
ⅷ Position the phone so the internal antenna is farthest from
your hearing aid.
ⅷ Any combined rating equal to five is considered normal use.
ⅷ Any combined rating equal to four is considered usable.
ⅷ Move the phone around to find the point with least
interference.
Thus, if you pair an M3 hearing aid with an M3 phone, you will
have a combined rating of six for “excellent use.”This is
synonymous for T ratings.
Nextel further suggests you experiment with multiple phones
(even those not labeled M3/T3 or M4/T4) while in the store to
122
Caring for the Environment by
Recycling
Export Law Assurances
This product is controlled under the export regulations of the
United States of America and Canada. The Governments of the
United States of America and Canada may restrict the
exportation or re-exportation of this product to certain
destinations. For further information contact the U.S.
Department of Commerce or the Canadian Department of
Foreign Affairs and International Trade.
This symbol on a Motorola product means the product
should not be disposed of with household waste.
Disposal of your Mobile Device and Accessories
Please do not dispose of mobile devices or electrical
accessories (such as chargers, headsets, or batteries) with
your household waste. These items should be disposed of in
accordance with the national collection and recycling schemes
operated by your local or regional authority. Alternatively, you
may return unwanted mobile devices and electrical
accessories to any Motorola Approved Service Center in your
region. Details of Motorola approved national recycling
schemes, and further information on Motorola recycling
activities can be found at: www.motorola.com/recycling.
California Perchlorate Label
Some mobile phones use an internal, permanent backup
battery on the printed circuit board that may contain very small
amounts of perchlorate. In such cases, California law requires
the following label:
Perchlorate Material – special handling may apply. See
www.dtsc.ca.gov/hazardouswaste/perchlorate. There is no special
handling required by consumers.
Disposal of your Mobile Device Packaging and
User’s Guide
Radio Frequency (RF) Energy
Product packaging and user’s guides should only be disposed
of in accordance with national collection and recycling
requirements. Please contact your regional authorities for more
details.
This section contains important information on the safe and
efficient operation of your mobile device. Read this
information before using your mobile device.
123
Using accessories not supplied or approved by Motorola may
cause your mobile device to exceed RF energy exposure
guidelines. For a list of Motorola-supplied or approved
accessories, visit our website at: www.motorola.com.
Exposure to Radio Frequency (RF) Energy
Your mobile device contains a transmitter and receiver. When it
is ON, it receives and transmits RF energy. When you
communicate with your mobile device, the system handling
your call controls the power level at which your mobile device
transmits.
RF Energy Interference/Compatibility
Nearly every electronic device is subject to RF energy
interference from external sources if inadequately shielded,
designed, or otherwise configured for RF energy compatibility.
In some circumstances your mobile device may cause
interference with other devices.
Your Motorola mobile device is designed to comply with local
regulatory requirements in your country concerning exposure
of human beings to RF energy.
Operational Precautions
Follow Instructions to Avoid Interference Problems
For optimal mobile device performance, and to be sure that
human exposure to RF energy does not exceed the guidelines
set forth in the relevant standards, always follow these
instructions and precautions.
ⅷ Turn off your mobile device in any location where posted
notices instruct you to do so.
ⅷ In an aircraft, turn off your mobile device whenever instructed
to do so by airline staff.
Product Operation
When placing or receiving a phone call, hold your mobile
device just like you would a landline phone.
ⅷ If your mobile device offers an airplane mode or similar
feature, consult airline staff about using it in flight.
Implantable Medical Devices
If you wear the mobile device on your body, always place the
mobile device in a Motorola-supplied or approved clip, holder,
holster, case, or body harness. If you do not use a body-worn
accessory supplied or approved by Motorola—or if you hang
your mobile device from a lanyard around your neck—keep the
mobile device and its antenna at least 2.5 centimeters (1 inch)
from your body when transmitting.
If you have an implantable medical device, such as a
pacemaker or defibrillator, consult your physician before using
this mobile device.
124
Persons with implantable medical devices should observe the
following precautions:
Operational Warnings
Obey all posted signs when using mobile devices in public
areas.
ⅷ ALWAYS keep the mobile device more than 20 centimeters
(8 inches) from the implantable medical device when the
mobile device is turned ON.
Potentially Explosive Atmospheres
ⅷ DO NOT carry the mobile device in the breast pocket.
Areas with potentially explosive atmospheres are often, but not
always, posted and can include fueling areas, such as below
decks on boats, fuel or chemical transfer or storage facilities, or
areas where the air contains chemicals or particles, such as
grain dust, or metal powders.
ⅷ Use the ear opposite the implantable medical device to
minimize the potential for interference.
ⅷ Turn OFF the mobile device immediately if you have any
reason to suspect that interference is taking place.
ⅷ Read and follow the directions from the manufacturer of your
implantable medical device. If you have any questions about
using your mobile device with your implantable medical
device, consult your healthcare provider.
When you are in such an area, turn off your mobile device, and
do not remove, install, or charge batteries. In such areas,
sparks can occur and cause an explosion or fire.
Knowing Radio Frequency Safety
Driving Precautions
The use of wireless phones while driving may cause
distraction. Discontinue a call if you can’t concentrate on
driving.
The design of your phone complies with updated NCRP standards
described below.
In 1991–92, the Institute of Electrical and Electronics Engineers
(IEEE) and the American National Standards Institute (ANSI) joined
in updating ANSI’s 1982 standard for safety levels with respect to
human exposure to RF signals. More than 120 scientists, engineers
and physicians from universities, government health agencies and
industries developed this updated standard after reviewing the
available body of research. In 1993, the Federal Communications
Commission (FCC) adopted this updated standard in a regulation.
In August 1996, the FCC adopted hybrid standard consisting of the
existing ANSI/IEEE standard and the guidelines published by the
Additionally, the use of wireless devices and their accessories
may be prohibited or restricted in certain areas. Always obey
the laws and regulations on the use of these products.
Responsible driving practices can be found in the “Smart
Practices While Driving” section in this guide (or separate
guide).
125
National Council of Radiation Protection and Measurements
(NCRP).
ⅷ American National Standards Institute (ANSI) / Institute of
Electrical and Electronics Engineers (IEEE). C95. 1-1992.
ⅷ Institute of Electrical and Electronics Engineers (IEEE). C95.
Body-Worn Operation
1-2005 Edition.1
To maintain compliance with FCC RF exposure guidelines, if
you wear a handset on your body, use the Motorola supplied or
approved carrying case, holster or other body-worn accessory.
If you do not use a body-worn accessory, ensure the antenna is
at least 2.5 centimeters from your body when transmitting. Use
of non-Motorola-approved accessories may violate FCC RF
exposure guidelines.
ⅷ International Commission on Non-Ionizing Radiation
Protection (ICNIRP) 1998.
ⅷ Ministry of Health (Canada). Safety Code 6. Limits of Human
Exposure to Radio frequency Electromagnetic Fields in the
Frequency Range from 3 kHz to 300 GHz, 1999.
ⅷ Australian Communications Authority Radio
communications (Electromagnetic Radiation - Human
Exposure) Standard 2003.
Your Motorola phone is designed to comply with local
regulatory requirements in your country concerning exposure
of human beings to RF energy.
ⅷ ANATEL, Brazil Regulatory Authority, Resolution 303 (July 2,
2002) “Regulation of the limitation of exposure to electrical,
magnetic, and electromagnetic fields in the radio frequency
range between 9 kHz and 300 GHz.” “Attachment to
Resolution 303 from July 2, 2002.”
For more information about RF exposure, visit the FCC website
at www.fcc.gov.
Portable Radio Product Operation and EME Exposure
ⅷ Your Motorola radio product is designed to comply with the
following national and international standards and guidelines
regarding exposure of human beings to radio frequency
electromagnetic energy (EME):
ⅷ United States Federal Communications Commission, Code
of Federal Regulations; 47 CFR part 2 sub-part J.
1.The information provided in this document supersedes the
general safety information in user’s guides published prior to
May 1, 2006.
126
multiple power levels so as to use only the power required to
reach the network. In general, the closer you are to a wireless
base station, the lower the power output.
Specific Absorption Rate
Your MOTOROLA i1 wireless phone meets the
governmental requirements for exposure to radio waves.
Before a phone model is available for sale to the public in the
U.S. and Canada, it must be tested and certified to the FCC
and Industry Canada that it does not exceed the limit
established by each government for safe exposure. The tests
are performed in positions and locations (e.g., at the ear and
worn on the body) submitted to the FCC and available for
review by Industry Canada. The highest SAR value for this
model phone when tested for use at the ear is 1.30 W/kg, and
when worn on the body, as described in this user guide, is
0.95 W/kg. Body-worn measurements can differ, depending
upon available accessories and regulatory requirements. The
SAR information includes the Motorola testing protocol,
assessment procedure, and measurement uncertainty range
for this product.
Your wireless phone is a radio transmitter and receiver. It is
designed and manufactured to not exceed limits for exposure
to radio frequency (RF) energy set by the Federal
Communications Commission (FCC) of the U.S. Government
and by the Canadian regulatory authorities. These limits are
part of comprehensive guidelines and establish permitted
levels of RF energy for the general population. The guidelines
are based on standards that were developed by independent
scientific organizations through periodic and thorough
evaluation of scientific studies. The standards include a
substantial safety margin designed for the safety of all persons,
regardless of age or health, and to account for any variations in
measurements.
The exposure standard for wireless mobile phones employs a
unit of measurement known as the Specific Absorption Rate
(SAR). The SAR limit set by the FCC and by the Canadian
regulatory authorities is 1.6 watts per kilogram (W/kg),
averaged over one gram of tissue. Tests for SAR are conducted
using procedures accepted by the FCC and by Industry
Canada with the phone transmitting at its highest certified
power level in all tested frequencies. Although the SAR is
determined at the highest certified power level, the actual SAR
level of the phone while operating can be below the maximum
value. This is because the phone is designed to operate at
While there may be differences between the SAR levels of
various phones and at various positions, they meet the
governmental requirements for safe exposure. Please note that
improvements to this product model could cause differences in
the SAR value for later products; in all cases, products are
designed to be within the guidelines.
Additional information on SAR can be found on the Cellular
Telecommunications & Internet Association (CTIA) website:
www.phonefacts.net or the Canadian Wireless
Telecommunications Association (CWTA) website: www.cwta.ca.
127
Owner’s Record
Software Copyright Notice
The model number, regulatory number, and serial number are
located on a nameplate inside the battery compartment.
Record the serial number in the space provided below. This will
be helpful if you need to contact us about your phone in the
future.
The Motorola products described in this manual may include
copyrighted Motorola and third party software stored in
semiconductor memories or other media. Laws in the United
States and other countries preserve for Motorola and third party
software providers certain exclusive rights for copyrighted
software, such as the exclusive rights to distribute or reproduce
the copyrighted software. Accordingly, any copyrighted
software contained in the Motorola products may not be
modified, reverse-engineered, distributed, or reproduced in any
manner to the extent allowed by law. Furthermore, the
purchase of the Motorola products shall not be deemed to
grant either directly or by implication, estoppel, or otherwise,
any license under the copyrights, patents, or patent
Model: MOTOROLA i1
Serial No.:
Online Product Registration:
http://www.motorola.com/us/productregistration
Product registration is an important step toward enjoying your
new Motorola product. Registration permits us to contact you
for product or software updates and allows you to subscribe to
updates on new products or special promotions. Registration is
not required for warranty coverage. Please retain your original
dated sales receipt, as you may need to provide it for warranty
validation in the future.
applications of Motorola or any third party software provider,
except for the normal, non-exclusive, royalty-free license to use
that arises by operation of law in the sale of a product.
Thank you for choosing a Motorola product.
128
Open Source Software Information
GPS and AGPS
For instructions on how to obtain a copy of any source code
being made publicly available by Motorola related to software
used in this Motorola mobile device you may send your request
in writing to:
Your mobile device can use Global Positioning System (GPS)
signals for location-based applications. GPS uses satellites
controlled by the U.S. government that are subject to changes
implemented in accordance with the Department of Defense
policy and the Federal Radio Navigation Plan. These changes
may affect the performance of location technology on your
mobile device.
MOTOROLA, INC.
OSS Management
600 North US Hwy 45
Libertyville, IL 60048
USA
Your mobile device can also use Assisted Global Positioning
System (AGPS), which obtains information from the cellular
network to improve GPS performance. AGPS uses your
wireless service provider's network and therefore airtime, data
charges, and/or additional charges may apply in accordance
with your service plan. Contact your wireless service provider
for details.
The Motorola website opensource.motorola.com also contains
information regarding Motorola’s use of open source.
Motorola has created the opensource.motorola.com to serve as a
portal for interaction with the software community-at-large.
To view additional information regarding licenses,
acknowledgments and required copyright notices for open
source packages used in this Motorola mobile device, please
Your Location
touch
> Settings> About Phone > Legal information >
Location-based information includes information that can be
used to determine the approximate location of a mobile device.
Mobile phones which are connected to a wireless network
transmit location-based information. Devices enabled with GPS
or AGPS technology also transmit location-based information.
Additionally, if you use applications that require location-based
information (e.g. driving directions), such applications transmit
location-based information. This location-based information
may be shared with third parties, including your wireless
Open source licenses.
129
service provider, applications providers, Motorola, and other
third parties providing services.
Privacy and Data Security
Motorola understands that privacy and data security are
important to everyone. Because some features of your phone
may affect your privacy or data security, please follow these
recommendations to enhance protection of your information:
Emergency Calls
When you make an emergency call, the cellular network may
activate the AGPS technology in your mobile device to tell the
emergency responders your approximate location.
ⅷ Monitor access: Keep your phone with you and do not leave
it where others may have unmonitored access. Lock your
device’s keypad where this feature is available.
AGPS has limitations and might not work in your area.
Therefore:
ⅷ Always tell the emergency responder your location to the
best of your ability; and
ⅷ Keep software up to date: If Motorola or a software/
application vendor releases a patch or software fix for your
phone which updates the device’s security, install it as soon
as possible.
ⅷ Remain on the phone for as long as the emergency
responder instructs you.
ⅷ Erase before recycling: Delete personal information or data
from your phone prior to disposing of it or turning it in for
recycling. For step-by-step instructions on how to delete all
personal information from your device, please contact your
local service provider.
Performance Tips
ⅷ Go outside and away from underground locations, covered
vehicles, structures with metal or concrete roofs, tall
buildings, and foliage. Indoor performance might improve if
you move closer to windows, but some window sun
shielding films can block satellite signals.
ⅷ Understanding AGPS: In order to comply with emergency
caller location requirements of the FCC, certain Motorola
phones incorporate Assisted Global Positioning System
(AGPS) technology. AGPS technology also can be used in
non-emergency applications to track and monitor a user’s
location, for example, to provide driving directions. Users
who prefer not to permit such tracking and monitoring
should avoid using such applications.
ⅷ Move away from radios, entertainment equipment, and other
electronic devices.
130
If you have further questions regarding how use of your phone
may impact your privacy or data security, please contact
Motorola.
ⅷ Position your phone within easy reach. Be able to access
your phone without removing your eyes from the road. If you
receive an incoming call at an inconvenient time, if possible,
let your voice mail answer it for you.
ⅷ Let the person you are speaking with know you are driving; if
necessary, suspend the call in heavy traffic or hazardous
weather conditions. Rain, sleet, snow, ice, and even heavy
traffic can be hazardous.
Smart Practices While Driving
Drive Safe, Call Smart SM
ⅷ Do not take notes or look up phone numbers while driving.
Jotting down a “to do” list or going through your address
book takes attention away from your primary responsibility,
driving safely.
Check the laws and regulations on the use of mobile devices
and their accessories in the areas where you drive. Always
obey them. The use of these devices may be prohibited or
restricted in certain areas. Contact www.motorola.com/callsmart
for more information.
ⅷ Dial sensibly and assess the traffic; if possible, place calls
when your car is not moving or before pulling into traffic. If
you must make a call while moving, dial only a few numbers,
check the road and your mirrors, then continue.
Your mobile device lets you communicate by voice and data—
almost anywhere, anytime, wherever wireless service is
available and safe conditions allow. When driving a car, driving
is your first responsibility. If you choose to use your mobile
device while driving, remember the following tips:
ⅷ Do not engage in stressful or emotional conversations that
may be distracting. Make people you are talking with aware
you are driving and suspend conversations that can divert
your attention away from the road.
ⅷ Get to know your Motorola phone and its features such as
speed dial and redial. If available, these features help you to
place your call without taking your attention off the road.
ⅷ Use your phone to call for help. Dial 911 or other local
emergency number in the case of fire, traffic accident, or
medical emergencies.*
ⅷ When available, use a hands-free device. If possible, add an
additional layer of convenience to your phone with one of the
many Motorola Original hands-free accessories available
today.
131
ⅷ Use your phone to help others in emergencies. If you see an
auto accident, crime in progress, or other serious emergency
where lives are in danger, call 911 or other local emergency
number, as you would want others to do for you.*
ⅷ Call roadside assistance or a special non-emergency
wireless assistance number when necessary. If you see a
broken-down vehicle posing no serious hazard, a broken
traffic signal, a minor traffic accident where no one appears
injured, or a vehicle you know to be stolen, call roadside
assistance or other special non-emergency wireless
number.*
* Wherever wireless phone service is available
132
Motorola Limited Warranty
for the United States and Canada
S2. Manufacturer’s Warranty
What does this Warranty Cover?
Subject to the exclusions contained below, Motorola, Inc.
warrants its telephones, pagers, messaging devices, and
consumer and professional two-way radios (excluding
commercial, government or industrial radios) that operate via
Family Radio Service or General Mobile Radio Service,
Motorola-branded or certified accessories sold for use with
these Products (“Accessories”) and Motorola software
contained on CD-ROMs or other tangible media and sold for
use with these Products (“Software”) to be free from defects in
materials and workmanship under normal consumer usage for
the period(s) outlined below. This limited warranty is a
consumer's exclusive remedy, and applies as follows to new
Motorola Products, Accessories and Software purchased by
consumers in the United States or Canada, which are
accompanied by this written warranty:
ࡗ ࡗ Your phone has been designed to provide you with
reliable, worry-free service. If for any reason you have a
problem with your equipment, please refer to the
manufacturer’s warranty in this section.
For information regarding the terms and conditions of service
for your phone, please visit www.nextel.com or call Nextel
Customer Service at 1-800-639-6111.
133
Products and Accessories
Products Covered
Length of Coverage
Products Covered
Length of Coverage
Products and
Accessories that are
Repaired or
The balance of the original
warranty or for ninety (90)
days from the date returned to
the consumer, whichever is
longer.
Products and
One (1) year from the date of
purchase by the first consumer
purchaser of the product unless
otherwise provided for below.
Accessories as
defined above,
unless otherwise
provided for below.
Replaced.
Decorative
Limited lifetime warranty for
the lifetime of ownership by
the first consumer purchaser
of the product.
Exclusions
Accessories and
Cases. Decorative
covers, bezels,
PhoneWrap™
Normal Wear and Tear. Periodic maintenance, repair and
replacement of parts due to normal wear and tear are excluded
from coverage.
covers and cases.
Batteries. Only batteries whose fully charged capacity falls
below 80% of their rated capacity and batteries that leak are
covered by this limited warranty.
Monaural Headsets. Limited lifetime warranty for
Ear buds and boom the lifetime of ownership by
Abuse, Misuse and Accidents. Defects or damage that result
from abuse, misuse or accidents, including but not limited to:
(a) improper handling, usage, operation or storage (e.g.
operating the Product outside its permitted or intended uses
including as set forth by Motorola in the Products specification
sheets or other documentation, or failing to comply with the
Products usage documentation); abuse/neglect (e.g. broken/
bent/missing clips/fasteners/connectors); (b) contact with
liquids, water, rain, extreme humidity, heavy perspiration or
other moisture, sand, food, dirt or similar substances caused
from incorrectly securing the phone’s protective elements or
headsets that
the first consumer purchaser
of the product.
transmit mono
sound through a
wired connection.
Consumer and
Professional
Two-Way Radio
Accessories.
Ninety (90) days from the date
of purchase by the first
consumer purchaser of the
product.
134
subjecting the Products to conditions beyond their stated
specification or limits; (c) use of the Products for commercial
rental purposes; or (d) external causes or acts which are not
the fault of Motorola, including but not limited to flood, fire,
earthquake, tornado or other acts of God, are excluded from
coverage.
Software
Products Covered
Length of Coverage
Software. Applies only to
physical defects in the media
that embodies the copy of the
software (e.g. CD-ROM, or
floppy disk).
Ninety (90) days
from the date of
purchase.
Use of Non-Motorola Products and Accessories. Defects or
damage that result from the use of Non-Motorola branded or
certified Products, Accessories, Software or other peripheral
equipment are excluded from coverage.
Exclusions
Unauthorized Service or Modification. Defects or damages
resulting from service, testing, adjustment, installation,
maintenance, alteration, or modification in any way by
someone other than Motorola, or its authorized service centers,
are excluded from coverage.
Software Embodied in Physical Media. No warranty is made
that the software will meet your requirements or will work in
combination with any hardware or software applications
provided by third parties, that the operation of the software
products will be uninterrupted or error free, or that all defects in
the software products will be corrected.
Altered Products. Products or Accessories with (a) serial
numbers or date tags that have been removed, altered or
obliterated; (b) broken seals or that show evidence of
tampering; (c) mismatched board serial numbers; or (d)
nonconforming or non-Motorola housings, or parts, are
excluded from coverage.
Software NOT Embodied in Physical Media. Software that is not
embodied in physical media (e.g. software that is downloaded
from the internet), is provided “as is” and without warranty.
Who Is Covered?
This warranty extends only to the first consumer purchaser, and
is not transferable.
Communication Services. Defects, damages, or the failure of
Products, Accessories or Software due to any communication
service or signal you may subscribe to or use with the Products
Accessories or Software is excluded from coverage.
135
(a) a copy of your receipt, bill of sale or other comparable proof
of purchase; (b) a written description of the problem; (c) the
name of your service provider, if applicable; (d) the name and
location of the installation facility (if applicable) and, most
importantly; (e) your address and telephone number.
What Will Motorola Do?
Motorola, at its option, will at no charge repair, replace or refund
the purchase price of any Products, Accessories or Software
that does not conform to this warranty. We may use functionally
equivalent reconditioned/refurbished/pre-owned or new
Products, Accessories or parts. No data, software or
applications added to your Product, Accessory or Software,
including but not limited to personal contacts, games and
ringer tones, will be reinstalled. To avoid losing such data,
software and applications please create a back up prior to
requesting service.
What other limitations are there?
ANY IMPLIED WARRANTIES, INCLUDING WITHOUT
LIMITATION THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, SHALL BE LIMITED TO THE DURATION OF THIS
LIMITED WARRANTY, OTHERWISE THE REPAIR,
REPLACEMENT, OR REFUND AS PROVIDED UNDER THIS
EXPRESS LIMITED WARRANTY IS THE EXCLUSIVE REMEDY
OF THE CONSUMER, AND IS PROVIDED IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED. IN NO EVENT
SHALL MOTOROLA BE LIABLE, WHETHER IN CONTRACT OR
TORT (INCLUDING NEGLIGENCE) FOR DAMAGES IN EXCESS
OF THE PURCHASE PRICE OF THE PRODUCT, ACCESSORY
OR SOFTWARE, OR FOR ANY INDIRECT, INCIDENTAL,
SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY KIND, OR
LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS
OF INFORMATION OR DATA, SOFTWARE OR APPLICATIONS
OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN
CONNECTION WITH THE ABILITY OR INABILITY TO USE THE
PRODUCTS, ACCESSORIES OR SOFTWARE TO THE FULL
EXTENT THESE DAMAGES MAY BE DISCLAIMED BY LAW.
How to Obtain Warranty Service or Other
Information
USA
Phones
1-800-453-0920
TTY
1-877-483-2840
For Accessories and Software, please call the
telephone number designated above for the
product with which they are used
You will receive instructions on how to ship the Products,
Accessories or Software, at your expense, to a Motorola
Authorized Repair Center. To obtain service, you must include:
136
Some states and jurisdictions do not allow the limitation
or exclusion of incidental or consequential damages, or
limitation on the length of an implied warranty, so the
above limitations or exclusions may not apply to you. This
warranty gives you specific legal rights, and you may also
have other rights that vary from state to state or from one
jurisdiction to another.
Laws in the United States and other countries preserve for
Motorola certain exclusive rights for copyrighted Motorola
software such as the exclusive rights to reproduce and
distribute copies of the Motorola software. Motorola software
may only be copied into, used in, and redistributed with, the
Products associated with such Motorola software. No other use,
including without limitation disassembly of such Motorola
software or exercise of the exclusive rights reserved for
Motorola, is permitted.
Service and Repairs
If you have questions or need assistance, we’re here to help.
a number of customer care options. You can also contact the
Motorola Customer Support Center at 1-800-453-0920 (United
States), 1-877-483-2840 (TTY/TDD United States for hearing
impaired).
137
Bluetooth Device Name 107
Bookmarks 61
Call Waiting 54
Off 54
Caller ID 53
Index
A
Accessories 25
Calls
Charger 25
Direct Connect Calls 32
Accessing 62
Li-Ion Battery 25
Activation 8
From Contacts 34
International 57
Phone Call While in Direct
Connect 32
Phone Calls 28
Talkgroup Calls 41
Using the Member ID 34
Creating 62
C
Airplane Mode 72
Alarm Clock 94
Android Keyboard 21
Answering Calls 28
Applications 15
Call Alerts
Answer 43
Deleting 44
Queue 44
Responding 44
Sending 43
Camcorder
Attachments 51
Viewing 44
Talking Pictures 100
Zoom 102
Clock Display 71
Adding an Entry 83
Assign a Picture to an Entry
Call Forwarding 55
B
All Calls 55
Off 56
Backlight 70
Charging 7
Disposal 120
Call Log
Deleting Call Log List 81
Safety 118
138
Creating 83
Pictures 37
Removing Members 36
Deleting 87
Receiving My Info 41
Receiving Pictures 38
Display Screen 16
Downloading Apps 63
H
I
Making Direct Connect Calls
Making Phone Calls 32
Searching 85
Hearing Aid Compatibility 121
Icons
Contacts 83
E
Status Information 16
In-Call Options 30
International Numbers 57
D
Email 64
DC Options 73
Dialing Codes
Non-Emergency Numbers 57
Telecommunications Relay
Service 57
Direct Connect
One Touch, Setting 73
Direct Connect Calls
Dialing 33
From Contacts 34
Member ID 34
Direct Connect Numbers 33
Contacts 40
Emergency Numbers 29
End-of-Call Options 31
Event Edit 89
K
L
Key Functions 13
Keyboard 21
G
Get Music 109
Gmail 64
Group Connect
Adding Group Members 36
Creating Groups 36
Deleting 36
Language 68
Latitude 91
M
Market
Menu
Navigation 18
Messaging
Groups vs. Talkgroups 41
MMS Messages 47
My Info 39
139
Notifications 46
Text Messaging (SMS) 53
Messaging Settings
Notification 71
Sending 39
Language 68
Prepend Dialing 73
N
Navigating Through Menus 18
Nextel Service
Account Passwords 10
Activation 8
Adapter 97
Inserting 95
Memory 98
R
Operator Services 11
Non-Emergency Numbers 57
Radio Frequency 123
Call Alerts 78
Removing 96
O
P
Attachments 51
Calls From 51
One Touch Direct Connect 73
Owner’s Record 128
My Info 79
Prepending a Number 81
Remote Direct Connect Button
Resetting Your Phone 76
Ringtones 68
Deleting 51
Pause Button 111
Pauses 31
Embedded Objects 51
Going to Website 52
Receiving 50
Storing 84
Phone (illus.) 12
Phone Number
Finding 31
Sending 48
S
Multimedia Messages
Music Set Up 109
My Info
Radio Frequency 123
Tips 115
Saving 31
With Pauses 31
Saving Attachments 53
140
Screen Lock 75
Search
Touch Tips 18
Transmitters
Bookmarks 62
Go to Websites 62
Reloading a Web Page 62
Web Browser 60
Widgets 14
TTY Devices 57
Turning Your Phone On and Off
Setup Wizard 9
Shortcuts 15
Silent Mode 70
SIM Card
Removing and Inserting 3
Security 74
SIM PIN 74
X
U
V
XT9 Text Input 22
Unlocking Your Phone 76
Vibrate All 69
Video 103
Swype Text Entry 23
T
Recording 103
Voicemail 47
Talkgroups 41
Join 42
Playing Messages 47
TDD/TTY Devices 57
Telecommunications Relay
Service 57
W
Waits
Text Messaging
Three-Way Calling 55
Storing 84
Wallpaper 70
141
|
