Sony MD Walkman MZ E75 User Manual

To lo ck t h e co n t ro ls (HOLD)  
To prevent the buttons from being  
accidentally operated when you carry the  
player, use this function.  
On cle a n in g  
BVa rio u s w a ys o f  
p la yb a ck  
BPo w e r so u rce s  
BAd d it io n a l in fo rm a t io n  
To  
Do this (Beeps in the  
headphones)  
3-045-493-21(1)  
Clean the player casing with a soft cloth  
slightly moistened with water or a mild  
detergent solution. Do not use any type of  
abrasive pad, scouring powder or solvent  
such as alcohol or benzene as it may mar  
the finish of the casing.  
Tro u b le sh o o t in g  
Sp e cifica t io n s  
You can use the player on a dry battery,  
house current, or a Ni-Cd rechargeable  
battery.  
Pre ca u t io n s  
Should any problem persist after you have  
made these checks, consult your nearest Sony  
dealer.  
Syst e m  
Pause  
Press X on the remote  
control. (Continuous  
short beeps)  
Playing an MD right  
away!  
Audio playing system  
MiniDisc digital audio system  
Laser diode properties  
Material: GaAlAs  
Wavelength: λ= 790 nm  
Emission duration: continuous  
Laser output: less than 44.6 µW*  
Bottom side of the player  
Slide HOLD on the player in the direction of  
the . to lock the controls of the unit.  
Slide HOLD on the remote control in the  
direction of the . to lock the controls of the  
remote control.  
On sa fe t y  
Do not put any foreign objects in the DC IN  
1.5V jack.  
DIGITAL SOUND PRESET  
Press X on the remote  
control again to  
The player does not w ork or w orks  
poorly.  
• You tried to play with no disc in the  
player (“NO DISC” flashes on the  
remote control).  
Wipe the disc cartridge with a dry cloth to  
remove dirt.  
Dust on the lens may prevent the unit from  
operating properly. Be sure to close the  
disc compartment lid after inserting or  
ejecting an MD.  
Usin g o n a d ry b a t t e ry  
Po rt a b le Min iDisc Pla ye r  
1
resume play.*  
1
Insert one LR6 (size AA) alkaline battery  
(not supplied) into the supplied battery  
case, and close the lid.  
On p o w e r so u rce s  
Charge the supplied rechargeable battery, before using it for the first  
time. Other choices are a dry battery and house current. For details, see  
“Power Sources”.  
Find the  
Press .once.  
For use in your house: Use the AC power  
adaptor AC-E15L (not supplied). Do not  
use any other AC power adaptor since it  
may cause the player to malfunction.  
Operating instructions  
Mode demploi (au dos)  
*
This output is the value measured at a  
distance of 200 mm from the objective lens  
surface on the optical pick-up block with  
7 mm aperture.  
beginning of  
the current  
track  
Press the control  
towards . on the  
remote control. (Three  
short beeps)  
b
Insert an MD.  
To a d ju st t h e so u n d q u a lit y  
(DIGITAL SOUND PRESET)  
You can make adjustments to the sound  
quality to suit your taste, and then store  
two sets of these adjustments.  
Close the lid securely by aligning the  
markings on the main unit and the lid.  
• The hold function is activated and the  
controls are locked. (If you press any of  
the operation buttons on the player,  
“HOLD” flashes on the remote control.)  
Stereo or monaural playback is automatically selected, depending on the  
sound source.  
On d ry b a t t e rie s a n d t h e b a t t e ry  
ca rryin g ca se  
Incorrect battery usage may lead to leakage of  
battery fluid or bursting batteries. To prevent  
such accidents, observe the following  
precautions:  
Revolutions  
800 rpm to 1800 rpm (CLV)  
Error correction  
Advanced Cross Interleave Reed Solomon Code  
(ACIRC)  
Sampling frequency  
Find the  
Press . repeatedly.  
Press the control  
towards . on the  
remote control  
repeatedly.  
(Continuous three  
short beeps)  
Markings  
e
beginning of  
the previous  
tracks  
b
Slide HOLD against the direction of  
the arrow to release the hold  
function.  
AVLS  
HOLD  
Polarity of the plug  
1
Slide DIGITAL SOUND PRESET to select  
1 or 2.  
1
Charge the rechargeable battery.  
E
Remote control  
If you are not going to use this player for a  
long time, be sure to disconnect the power  
supply (AC power adaptor, dry battery, or  
rechargeable battery). To remove the AC  
power adaptor from the wall outlet, grasp  
the adaptor plug itself; never pull the cord.  
If you want, you may also listen to MDs  
without making any adjustments (i.e., by  
using the factory settings).  
OFF 1 2  
Install batteries with the + and – poles  
aligned correctly.  
44.1 kHz  
Coding  
Install the supplied rechargeable battery NC-6WM to the  
supplied battery charger with correct polarity, and connect to a  
wall outlet.  
• Moisture has condensed inside the  
player.  
g
g
DISPLAY  
TM  
MZ-E75  
Adaptive TRansform Acoustic Coding (ATRAC)  
Modulation system  
EFM (Eight to Fourteen Modulation)  
Number of channels  
2 stereo channels  
1 monaural channel  
Frequency response  
20 to 20,000 Hz ± 3 dB  
Wow and Flutter  
Below measurable limit  
Outputs  
Headphones: stereo mini-jack, maximum output  
level 5 mW + 5 mW, load impedance 16 ohms  
Do not try to recharge dry batteries.  
When the player is not to be used for a long  
time, be sure to remove the batteries.  
If a battery leak should develop, carefully  
and thoroughly wipe away battery fluid  
from the battery compartment before  
inserting new ones.  
b
Take the MD out and leave the  
players lid open for several hours  
until the moisture evaporates.  
Find the  
beginning of  
the next track  
Press > N once.  
Press the control  
towards N/ > on  
the remote control.  
(Two short beeps)  
PLAYMODE  
HOLD  
Sony Corporation © 2000 Printed in Japan  
• U.S.A. and European UK model  
• Other countries model  
DIGITAL  
SOUND PRESET  
Make sure the + and –  
terminals are correctly  
oriented.  
continental model  
(Full charging takes  
150 minutes.)  
(Full charging takes  
3 hours and 30  
minutes.)  
(Full charging takes 60 minutes.)  
• The rechargeable battery or dry battery  
is weak (“LOW BATT” flashes on the  
remote control).  
On ch a rg in g  
to a w all  
2
During playback, hold down DISPLAY  
or PLAYMODE until the following  
indicator appears on the remote control.  
Press DISPLAY to select bass, and  
PLAYMODE to select treble.  
Be sure to use the supplied battery charger.  
Charging time may vary depending on the  
battery condition.  
outlet  
lamp  
Go backwards Hold down ..  
while  
playing*  
2
Attach the battery case to the player.  
Do not carry the dry battery in your pocket  
or a bag, etc., with metallic objects such as  
key rings. The terminals of the battery or  
the battery carrying case may heat up from  
a short-circuit and can be dangerous.  
b
Replace the dry battery or recharge  
the battery.  
Reorient or relocate the receiving antenna.  
Increase the separation between the  
equipment and receiver.  
Connect the equipment into an outlet on a  
circuit different from that to which the  
receiver is connected.  
to a w all  
outlet  
Press and hold the  
control towards .  
on the remote control.  
to a w all  
outlet  
WARNING  
1
When you use the battery for the first time  
or after a long period of disuse, the battery  
life may be shorter. In this case, charge  
and discharge the battery several times.  
The battery life will be restored.  
Pla yin g t ra cks re p e a t e d ly  
• The rechargeable battery or dry battery  
has been installed incorrectly.  
To p re ve n t fire o r sh o ck  
h a za rd , d o n o t e xp o se  
t h e u n it t o ra in o r  
m o ist u re .  
NC-6WM  
(supplied)  
Go forward  
while  
playing*  
Hold down > N.  
Press and hold the  
control towards N/  
> on the remote  
control.  
You can play tracks repeatedly in three ways  
— all repeat, single repeat, and shuffle repeat.  
b
Install the battery with correct  
polarity.  
1
Consult the dealer or an experienced  
radio/ TV technician for help.  
On t h e lid o f t h e b a t t e ry ca se  
The lid of the battery case supplied with this  
player is designed to detach from the main  
unit when handled with great force. To  
reattach the lid to the main unit, follow the  
steps below:  
Ge n e ra l  
Pow er requirements  
When you select bass-setting mode, “B”  
appears. When you select treble-setting  
mode, “Tappears.  
NC-6WM  
(supplied)  
NC-6WM  
(supplied)  
If the rechargeable battery capacity  
becomes half the normal life, replace it  
with a new one.  
Remove the rechargeable battery when the  
unit is not to be used for a long time. Do  
not carry the rechargeable battery in your  
pocket or a bag, etc., with metallic objects  
such as key rings.  
The charger lamp  
goes off when the  
charging has finished.  
• An MD with no recording on it is  
inserted (“BLANKDISC” flashes on the  
remote control).  
Press PLAYMODE while the player is playing  
an MD.  
Each time you press PLAYMODE, the play  
mode indication changes as follows.  
This device complies with Part 15 of the FCC  
Rules. Operation is subject to the following  
two conditions: (1) This device may not cause  
harmful interference, and (2) this device must  
accept any interference received, including  
interference that may cause undesired  
operation.  
Nickel cadmium rechargeable battery  
NC-6WM (supplied)  
One LR6 (size AA) battery (not supplied)  
Sony AC Power Adaptor AC-E15L* (not  
supplied) connected to the DC IN 1.5V jack  
Battery operation time  
To a vo id e le ct rica l  
sh o ck, d o n o t o p e n t h e  
ca b in e t . Re fe r se rvicin g  
t o q u a lifie d p e rso n n e l  
o n ly.  
Remove the  
MD  
Press x, and then  
b
Insert a recorded MD.  
3
Press N/> or . on the remote  
repeatedly to adjust the bass or the treble.  
Adjust the sound as you listen to it.  
Example: While adjusting the bass.  
The cursor moves. (Position: –2)  
2
press OPEN.*  
• The player cannot read the disc (its  
scratched or dirty) (“DISC ERR” flashes  
on the remote control).  
Play mode indication  
2
If p la yb a ck d o e s n o t st a rt  
Make sure the player is not locked. For  
details, see “To lock the controls  
(HOLD)”.  
Insert the rechargeable battery.  
Projections  
Slots  
Turn tow ards LOCK.  
To release the battery case, turn  
towards RELEASE.  
See “When to replace or charge the batteries”  
Dimensions  
1 Slide open the battery  
compartment as shown in the  
illustration.  
2 Insert the battery.  
b
Reinsert or replace the disc.  
You are cautioned that any changes or  
modifications not expressly approved in this  
manual could void your authority to operate  
this equipment.  
On t h e b a t t e ry ca se a t t a ch m e n t  
t e rm in a ls o n t h e m a in u n it  
Approx. 86 × 16.3 × 75.4 mm (w/ h/ d)  
• While operating, the player received a  
mecanical shock, too much static,  
abnormal power voltage caused by  
lightning etc.  
21  
(3 1/  
×
/
32 × 3 in.) not including projecting parts  
Ca u t io n  
(none) (normal play)  
All the tracks are played once.  
b
2
When to replace or charge the batteries  
You can check the battery condition with the  
battery indication which is displayed while using  
the player.  
and controls  
The use of optical instruments with this  
product will increase eye hazard.  
Do not short-circuit the battery case  
attachment terminals on the main unit with  
metallic objects, etc., when the  
Fo r m o d e ls su p p lie d w it h t h e AC  
p lu g a d a p t o r  
If the battery charger does not fit the wall  
Mass  
e
E
m
–4  
±0  
+3  
Approx. 98 g (3.5 oz.) the player only  
Approx. 138 g (5.0 oz.) incl. a premastered MD  
and a nickel cadmium rechargeable battery  
NC-6WM  
Supplied accessories  
Battery Charger (1)  
Rechargeable battery (1)  
Rechargeable battery carrying case (1)  
Headphones with a remote control (1)  
Dry battery case (1)  
Fo r cu st o m e rs in t h e Un it e d St a t e s  
a n d Ca n a d a  
F” (all repeat)  
All the tracks are played repeatedly.  
b
Restart as follows.  
The sound can be adjusted in 8 steps  
(–4, –3…±0…+2, +3).  
rechargeable battery is inserted, as this  
may cause heat and can be dangerous.  
When carrying the player in a bag, be sure  
to put it in the supplied carrying pouch.  
CAUTION — LASER RADIATION WHEN  
OPEN  
outlet, use the AC plug adaptor.  
Make sure the + and –  
terminals are correctly  
oriented.  
t
v
r
v
Battery power decreasing  
1 Disconnect all the power sources.  
2 Leave the player for about  
30 seconds.  
RECYCLING NICKEL-CADMIUM  
BATTERIES  
m
If you hold down PLAYMODE while in  
bass-setting mode, the mode will change  
to treble-setting mode. If you hold down  
DISPLAY while in treble-setting mode,  
the mode will change to bass-setting  
mode.  
1Place the lid so that the projections on the  
lid are aligned with the slots on the main  
unit.  
Disp la y w in d o w w h ile p la yin g  
b a ck  
For details, see “To know the track name  
Weak batteries.  
F1” (single repeat)  
A single track is played repeatedly.  
DO NOT STARE INTO BEAM OR VIEW  
DIRECTLY WITH OPTICAL INSTRUMENTS  
Nickel-Cadmium batteries are  
recyclable. You can help  
preserve our environment by  
returning your unwanted  
batteries to your nearest point  
for collection, recycling or  
3 Connect the power source.  
e
The batteries have gone out. “LOW  
BATT” flashes in the display on the  
remote control, and the power goes off.  
m
On h e a t b u ild -u p  
and time”.  
The MD is not played normally.  
• The player is set to the repeat mode  
(“F” is displayed on the remote  
control).  
2
1
Heat may build up in the player if it is used  
for an extended period of time. In this case,  
leave the player to cool down.  
F SHUF” (shuffle repeat)  
All the tracks are played repeatedly in  
random order.  
Listening for many hours at maximum  
volume may damage your hearings.  
Track name*3 or elapsed time of  
the track being played  
Carrying pouch (1)  
Battery life*  
4
Press DISPLAY or PLAYMODE.  
The sound settings are saved and the  
playback display appears again.  
If you perform no sound adjustments for  
a given duration of time, the playback  
display appears again and any settings  
that were made are saved.  
proper disposal.  
3
4
In fo rm a t io n  
Insert an MD.  
b
Press PLAYMODE repeatedly until  
Fdisappears, then start  
playing.  
Note: In some areas the disposal of nickel-  
cadmium batteries in household or business  
trash may be prohibited.  
On in st a lla t io n  
Op t io n a l a cce sso rie s  
AC-E15L AC power adaptor * (except for  
Australia)  
MDR-series Stereo headphones **  
SRS-series Sony Active Speakers  
Batteries  
Playback  
IN NO EVENT SHALL SELLER BE LIABLE  
FOR ANY DIRECT, INCIDENTAL OR  
CONSEQUENTIAL DAMAGES OF ANY  
NATURE, OR LOSSES OR EXPENSES  
RESULTING FROM ANY DEFECTIVE  
PRODUCT OR THE USE OF ANY PRODUCT.  
Never use the player where it will be  
subjected to extremes of light, temperature,  
moisture or vibration.  
1 Press OPEN.  
2 Insert an MD and press the lid down to  
Ni-Cd  
Approx. 8 hours**  
Track number  
close.  
rechargeable battery  
(NC-6WM)  
An MD is not played from the first track.  
• Disc playing stopped before it came to  
the last track.  
2Fit the projection one by one in to the slot  
as shown in the illustration.  
RBRC (Rechargeable Battery Recycling  
Corporation) advises you about spent battery  
collection by the following phone number.  
Call toll free number: 1-800-822-8837  
(United States and Canada only)  
Never wrap the player in anything when it  
is being used with the AC power adaptor.  
Heat build-up in the player may cause  
malfunction or injury.  
Tip s o n p la yb a ck  
Tips  
• The OPERATE lamp on the player lights  
up on the player during playback. When  
you press x, the lamp goes off.  
• The display on the remote control  
disappears after a while after you have  
pressed x.  
One LR6 (size AA)  
alkaline battery  
Approx. 22 hours  
*
The operative voltage for the AC power  
adaptor varies depending upon the country in  
which it is sold. Therefore, purchase the AC  
power adaptor in the country you intend to  
use it.  
b
Press . repeatedly or eject and  
reinsert the MD once to go back to  
the beginning of the disc, and restart  
playing after checking the track  
number in the display.  
To kn o w t h e t ra ck n a m e a n d t im e  
Press DISPLAY on the remote control while  
the player is playing an MD.  
Each time you press DISPLAY, the display  
changes as follows.  
No t e o n m e ch a n ica l n o ise  
The player gives out mechanical noise while  
operating, which is caused by the power-  
saving system of the player. This is not a  
malfunction.  
Returning the MD player to its factory  
settings  
To return the MD player to its factory settings,  
reset the following items to the value indicated:  
• DIGITAL SOUND PRESET 1:  
bass +1, treble ±0  
Certain countries may regulate disposal of the  
battery used to power this product.  
Please consult with your local authority.  
One LR6 (size AA)  
alkaline battery and  
a Ni-Cd  
Approx. 32 hours**  
Caution: Do not handle damaged or leaking  
nickel-cadmium batteries.  
On t h e h e a d p h o n e s  
Road safety  
“MD WALKMAN” is a trademark of Sony  
Corporation.  
Fo r cu st o m e rs in Au st ra lia  
rechargeable battery  
(NC-6WM)  
Do not use headphones while driving,  
cycling, or operating any motorized vehicle. It  
may create a traffic hazard and is illegal in  
many areas. It can also be potentially  
dangerous to play your player at high volume  
while walking, especially at pedestrian  
crossings. You should exercise extreme  
caution or discontinue use in potentially  
hazardous situations.  
** Whether you should plug the headphones  
directly to the i1 (or i2) jack on the main unit  
or to a remote control, use only headphones  
with stereo mini plugs.  
Elapsed time  
If the supply cord of the AC power adaptor is  
damaged, the AC power adaptor must be  
returned to the manufacturer or his agent for  
the cord to be replaced.  
The Digital Sound Preset function does  
not function.  
• The DIGITAL SOUND PRESET switch  
is set to OFF.  
With label facing upw ard, insert disc in  
direction of the arrow .  
Note  
If you have any questions or problems  
concerning your player, please consult your  
nearest Sony dealer.  
• DIGITAL SOUND PRESET 2:  
bass +3, treble ±0  
Do not press OPEN during playback. If  
you do, the lid opens and playback stops.  
Fo r cu st o m e rs in t h e Un it e d St a t e s  
Ow n e r’s Re co rd  
* The battery life may be shorter depending on  
operating conditions and the temperature of  
the location.  
b
Notes  
The model number is located at the bottom  
and near the display and the serial number is  
located on the floor of the disc compartment.  
Record the serial number in the space  
provided below. Refer to them whenever you  
call upon your Sony dealer regarding this  
product.  
b
Set the switch to 1 or 2.  
Play an MD.  
When using optional headphones  
• Use headphones with a stereo-miniplug.  
You cannot use headphones with a  
microplug.  
• In addition to the i1 jack, you can connect  
headphones to the i2 jack as well.  
stereo mini plugs  
• Settings can also be changed while playback is  
momentarily paused (X).  
• Settings cannot be changed through the  
operation buttons on the player.  
• Settings cannot be changed while the DIGITAL  
SOUND PRESET switch is set to OFF.  
**With a fully charged battery  
Track number  
m
Playback sound skips.  
• The player is placed where it receives  
continuous vibration.  
We lco m e !  
Bottom side of  
the player  
i2 jack  
x
Track name  
Welcome to the world of the MiniDisc! Here  
are some of the capabilities and features  
youll discover with the new MiniDisc Player.  
Small body almost the size of a MiniDisc  
jacket  
Ideal weight and size; fits in your shirt  
pocket.  
Simple “Pop-Up Eject” function for easy  
MiniDisc handling  
A single press of a button on the side of the  
player causes the player lid to open and the  
MiniDisc to eject.  
Personalized sound through Digital  
Sound Preset functions  
You can store two sets of sound quality  
adjustments (made during playback) to  
two switches.  
Dual phone jacks for greater versatility  
Two phone jacks are provided for  
connection of up to two headphones.  
Easy-to-operate headphones remote  
control w ith backlit LCD  
Keep the main unit in your pocket and  
operate the MiniDisc player through the  
“slim stick” remote control. The LCD  
displays disc and track information,  
playback mode as well as battery  
condition.  
Low pow er-consumption design enables  
extended battery life.  
Shock-resistant memory offsets up to  
40 seconds of optical read errors.  
Usin g o n h o u se cu rre n t  
Use to connect a second  
pair of headphones, etc.  
b
Put the player on a stable place.  
• A very short track may cause sound to  
skip.  
Preventing hearing damage  
Avoid using headphones at high volume.  
Hearing experts advise against continuous,  
loud and extended play. If you experience a  
ringing in your ears, reduce the volume or  
discontinue use.  
Remove the rechargeable battery when using  
the unit on house current.  
1
Model No. MZ-E75  
Serial No.  
*
When you press . or > N on the  
player during pause (X), the player  
resumes playback.  
If you hold down . or > N on the  
player (or press and hold the control  
towards . or N/> on the remote  
control) during pause (X), you can fast  
forward/ rewind without listening to the  
playback sound.  
Once you open the lid, the point to start  
playback will change to the beginning of  
the first track.  
Appears only with MDs that have been  
electronically labeled.  
Your dealer may not handle some of the above  
listed accessories. Please ask the dealer for  
detailed information about the accessories in  
your country.  
Remote  
control  
To p ro t e ct yo u r h e a rin g (AVLS)  
The AVLS (Automatic Volume Limiter  
System) function keeps down the maximum  
volume to protect your ears.  
Sound has a lot of static.  
• Strong magnetism from a television or  
such device is interfering with  
operation.  
3
1
Track number  
m
1
2
Attach the supplied battery case to the  
player.  
N/>  
x
In fo rm a t io n  
This equipment has been tested and found to  
comply with the limits for a Class B digital  
device, pursuant to Part 15 of the FCC Rules.  
These limits are designed to provide  
4
Disc name  
2
.
4
Caring for others  
Connect the AC-E15L AC power adaptor  
(not supplied) to the DC IN 1.5V jack of  
the battery case.  
b
Move the player away from the  
source of strong magnetism.  
US and foreign patents licensed from Dolby  
Laboratories Licensing Corporation.  
Set AVLS to LIMIT.  
Keep the volume at a moderate level. This  
will allow you to hear outside sounds and to  
be considerate of the people around you.  
The volume is kept at a moderate level, even  
if you try to turn the volume above the  
limited level.  
3
i1 jack  
reasonable protection against harmful  
interference in a residential installation. This  
equipment generates, uses, and can radiate  
radio frequency energy and, if not installed  
and used in accordance with the instructions,  
may cause harmful interference to radio  
communications. However, there is no  
guarantee that interference will not occur in a  
particular installation. If this equipment does  
cause harmful interference to radio or  
television reception, which can be determined  
by turning the equipment off and on, the user  
is encouraged to try to correct the interference  
by one or more of the following measures:  
2
The rechargeable battery does not start  
charging (in case of a charger w ith a  
lid).  
• The lid of the battery charger is not  
closed properly.  
*
Design and specifications are subject to change  
without notice.  
3
Connect the AC power adaptor to a wall  
outlet.  
Number of tracks recorded on the MD  
OPERATE lamp  
NORM LIMIT  
On t h e Min iDisc ca rt rid g e  
3
*
Do not touch the internal disc directly.  
Forcing the shutter open may damage the  
internal disc.  
1 Connect the headphones to the remote control.  
AVLS  
to a w all outlet  
Note  
Plug it in firmly all the way.  
b
Close the lid and slide the lock.  
Disc and track names appear only with MDs that  
have been electronically labeled.  
2 Connect the headphones with the remote control to the i1 jack.  
3 Press > N (or press the control towards N/> or . on the remote  
Do not place the cartridge where it will be  
subjected to light, temperature, moisture or  
dust.  
No sound comes through the  
headphones.  
• The headphones plug is not firmly  
connected.  
control).  
The OPERATE lamp on the player lights up and the player starts to play the first  
track. When using the remote control, a short beep sounds in the headphones.  
b
Connect the headphones plug firmly  
to the remote control.  
4 Press VOLUME +/– (or press VOL +/– on the remote control) to adjust the  
volume.  
b
Connect the headphones plug firmly  
to the i1 (or i2) jack.  
to DC IN 1.5V jack  
The volume indicator appears on the remote control to allow you to check the  
volume.  
• Volume is too low.  
Note  
b
Adjust the volume by pressing  
VOLUME +/ – (VOL +/ – on the  
remote control).  
The battery indication is displayed while using  
the AC power adaptor.  
To stop play, press x.  
The OPERATE lamp on the player goes off. The display on the remote control  
disappears after a while. When using the remote control, a long beep sounds in the  
headphones.  
• AVLS is on.  
Slide AVLS to NORM.  
b

Toshiba MHZ2080BJ User Manual
Sunbeam MR COFFEE FT User Manual
Sony ICF C215 User Manual
Sony DRU 500A User Manual
Sony CLIE User Manual
Sony 16GB Micro Vault Click USB20 Flash Drive USM16GL User Manual
Samsung SPH A513 Fin User Manual
RCA CD Player RP2422 User Manual
Panasonic SL PD8 User Manual
Oregon Clock RRM320PA User Manual