4-156-864-12(1)
Multi-Function
DVD Recorder
Operating Instructions
VRD-MC6
© 2009 Sony Corporation
7) Do not block any ventilation openings.
Install in accordance with the
manufacturer’s instructions.
8) Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that
produce heat.
9) Do not defeat the safety purpose of the
polarized or grounding-type plug. A
polarized plug has two blades with one
wider than the other. A grounding type plug
has two blades and a third grounding prong.
The wide blade or the third prong are
provided for your safety. If the provided
plug does not fit into your outlet, consult an
electrician for replacement of the obsolete
outlet.
10) Protect the power cord from being
walked on or pinched particularly at plugs,
convenience receptacles, and the point
where they exit from the apparatus.
11) Only use attachments/accessories
specified by the manufacturer.
FCC Compliance Statements
This equipment has been tested and found
to comply with the limits for a Class B
digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to
provide reasonable protection against
harmful interference in a residential
installation.
This equipment generates, uses, and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation.
If this equipment does cause harmful
interference to radio or television reception,
which can be determined by turning the
equipment off and on, the user is
encouraged to try to correct the interference
by one or more of the following measures:
- Reorient or relocate the receiving
antenna.
12) Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
- Increase the separation between the
equipment and receiver.
- Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced
radio/TV technician for help.
You are cautioned that any changes or
modifications not expressly approved in
this manual could void your authority to
operate this equipment.
13) Unplug this apparatus during lightning
storms or when unused for long periods of
time.
The manufacturer of this product is Sony
Corporation, 1-7-1 Konan Minato-ku
Tokyo, 108-0075 Japan. The Authorized
Representative for EMC and product safety
is Sony Deutschland GmbH, Hedelfinger
Strasse 61, 70327 Stuttgart, Germany. For
any service or guarantee matters please
refer to the addresses given in separate
service or guarantee documents.
14) Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way,
such as power-supply cord or plug is
damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does
not operate normally, or has been dropped.
3
Perchlorate Material: Lithium battery
contains perchlorate.
Notes on AC power adapter
• Please ensure that the socket outlet is installed
near the equipment and shall be easily
accessible.
• Be sure to use the supplied AC adapter and
power cord.
• Do not use any other AC adapter. It may cause a
malfunction.
• Connect the AC adapter to an easily accessible
socket outlet.
• Do not touch the AC adapter with wet hands.
• Should you notice an abnormality in the AC
adapter, disconnect it from the socket outlet
immediately.
• Use a commercially available AC plug adapter,
if necessary, depending on the design of the wall
outlet.
For customers in the United Kingdom
and Republic of Ireland
A molded plug complying with BS1363 is
fitted to this equipment for your safety and
convenience. Should the fuse in the plug
supplied need to be replaced, a fuse of the
same rating as the supplied one and
approved by ASTA or BSI to BS1362, (i.e.,
marked with
or mark) must be used.
If the plug supplied with this equipment has
a detachable fuse cover, be sure to attach
the fuse cover after you change the fuse.
Never use the plug without the fuse cover.
If you should lose the fuse cover, please
contact your nearest Sony service station.
Disposal of Old Electrical & Electronic
Equipment (Applicable in the
European Union and other European
countries with separate collection
systems)
• The set is not disconnected from the AC power
source (mains) as long as it is connected to the
wall outlet, even if the set itself has been turned
off.
The nameplate is located on the bottom of
the unit.
This symbol on the product
or on its packaging indicates
that this product shall not be
treated as household waste.
Instead it shall be handed
over to the applicable
For Customers in U.S.A
Owner’s Record
The product label is located on the bottom
of the unit. Record the serial number in the
space provided below. Refer to them
whenever you call upon your Sony dealer
regarding this product.
collection point for the
recycling of electrical and
electronic equipment. By ensuring this
product is disposed of correctly, you will
help prevent potential negative
consequences for the environment and
human health, which could otherwise be
caused by inappropriate waste handling of
this product. The recycling of materials will
help to conserve natural resources. For
more detailed information about recycling
of this product, please contact your local
Civic Office, your household waste
disposal service or the shop where you
purchased the product.
Model:
Serial Number: ________
VRD-MC6
For the State of California, USA only
Perchlorate Material - special handling may
apply, See
perchlorate
4
• DVDirect, Handycam, CyberShot, Memory Stick and their logos are trademarks, or registered trademarks
of Sony Corporation.
• AVCHD and the AVCHD logo are trademarks of Sony Corporation and Panasonic Corporation.
• “PLAYSTATION” is a registered trademark of Sony Computer Entertainment Inc.
• Other system and product names used herein are registered trademarks or trademarks of their respective
manufacturers, although the ™ and ® marks are not used in the text.
• Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby Laboratories.
• The authorized software in this product is used under license from eSOL Co. Ltd.
❑ Our product warranty is valid only when the supplied accessories are used in the specified or
recommended system environment, in accordance with the documentation, and applies only to this
DVDirect. Our customer service and user support apply only under these product warranty
conditions.
❑ Please note that we cannot accept responsibility for failure of the computer or other devices,
incompatibility with special hardware, operating problems caused by improper installation of
software, loss of data, discs or other accidental or incidental damage that might occur when using
this product.
❑ The guarantee and user support for this product are valid only within the countries or sales regions
specified on the warranty card.
❑ Specifications may be changed without notice in the interest of product improvement.
Copyright
Television programs, films, video tapes, discs, and other materials may be copyrighted.
Unauthorized recording of such material may be contrary to the provisions of the copyright
laws. Also, use of this product with cable television transmission may require authorization
from the cable television transmitter and/or program owner.
5
Table of Contents
Selecting copy mode
Find a type of copy mode ................8
Type of copy modeA
Record HD video as is.................10
Connecting Cables for Recording
Type of copy modeB
Down-convert videos to SD
(Standard Definition) quality ........12
Type of copy modeC
Record SD (Standard Definition)
video as is....................................14
Type of copy modeD
Record SD (Standard Definition)
video as is....................................16
Copying and Consolidating Contents
Type of copy modeE
Connect other video device and
record SD (Standard Definition)
video ............................................18
Copying a photo ............................20
Recording HD (High Definition)
Recording SD (Standard Definition)
6
Supported Discs and Memory Cards
Recording Time and Video Lengths
7
Videos
Selecting copy mode
Find a type of copy mode
Depending on your video device or the type of disc you are creating, you can
select the copy mode and device connection that best serves your needs.
Select the type of disc to create
The following explains about selecting a copy mode of video. For details on copying a photo, refer
to page 20.
I want to record HD (High Definition) video as is.
HD (High Definition) Disc (AVCHD format)
AVCHD format compatible device
Sony Blu-ray Disc
player/recorder
Playstation3®
Compatible
players
Not playable on DVD players/recorders.
I want to enjoy playback on various DVD players.
SD (Standard Definition) Disc
DVD player/recorder
Computer
Compatible
players
8
About Handycam®
In this manual, Handycam® refers to a Sony camcorder. High Definition Handycam® and
AVCHD Handycam® refer to a Sony HD (High Definition) camcorder.
Which device did
you use to capture
the video?
What image quality
does the video have?
: High Definition
: Standard Definition
Type of copy mode
Sony High Definition
Digital video camera
Digital still camera
b page 10
Sony Standard
Definition
Digital video camera
You cannot
create HD (High
Definition) disc.
You cannot create HD (High
Definition) disc.
Other video device
(video camera, VHS
recorder, etc.)
Type of copy mode
Down-converted to SD
(Standard Definition)
during recording.
b page 12
Sony High Definition
Digital video camera
b page 14
Sony Standard
Definition
Digital video camera
*
b page 16
Other video device
(video camera, VHS
recorder, etc.)
*
Down-converted to SD
(Standard Definition)
during recording.
b page 18
9
Videos
Type of copy mode
Record HD video as is
What is the recording
media?
Connection and setup
Use a USB cable
(supplied with camera or sold
separately)
HDD
b page 31
Use a USB cable
(supplied with camera or sold
separately)
b page 31
Built-in memory
Memory Card
Insert a Memory Card into
1
the slot*
b page 36
*
1 You can record video by connecting a
camera via a USB cable.
Recording is not available.
You can record by down-
converting to SD (Standard
Definition). See Type of copy
8cm Disc
Recording is not available.
DV tape
(HDV format)
You can record by down-
converting to SD (Standard
Definition). See Type of copy
10
Select the copy mode and
create a disc!
One Touch
Disc Burn
Press the button on
camera
Copying All
Contents
The entire contents
of camera
Copying
Only New
Video
Only the new contents
of camera
Copying
Copying
Visual Index
Lists
Select by a scene/
shooting date
3
Playlist*
Playlist contents on
camera
4
2
*2 Recording possible only when connected to a camera via USB cable. Only some models
support One Touch Disc Burn.
*3 Copying Playlist is possible only with cameras that can create a playlist.
*4 Built-in memory of “HYBRID Plus” Handycam® cannot be recorded by One Touch Disc Burn.
b Note
• You cannot record HD (High Definition) video taken in REC mode at a bit rate exceeding
18Mbps, such as in [HD FX] mode (for example, High Definition Handycam®) in AVCHD
format. In this case, you can record by down-converting to SD (Standard Definition) quality. See
11
Videos
Type of copy mode
Down-convert videos to SD (Standard
Definition) quality
What is the recording
media?
Connection and setup
Use an AV cable
(supplied with camera or sold
separately)
HDD
b page 34
Use an AV cable
(supplied with camera or sold
separately)
b page 34
Built-in memory
8cm Disc
Use an AV cable
(supplied with camera or sold
separately)
b page 34
Use an AV cable
(supplied with camera or sold
separately)
Memory Card
b page 34
Use an AV cable
(supplied with camera or sold
separately)
b page 34
DV tape
(HDV format)
Use a DV (i.LINK) cable
(supplied with camera or sold
separately)
Set the [i.LINK CONV] setting on the
Handycam® to [ON].
b page 33
12
Videos
Type of copy mode
Record SD (Standard Definition) video as is
What is the recording
media?
Connection and setup
Use a USB cable
(supplied with camera or sold
separately)
HDD
b page 31
Use a USB cable
(supplied with camera or sold
separately)
b page 31
Built-in memory
8cm Disc
Use a USB cable
(supplied with camera or sold
separately)
b page 31
Insert a Memory Card into
1
the slot*
Memory Card
b page 36
*
1 You can record video by connecting a
camera via a USB cable.
Use a DV (i.LINK) cable
(supplied with camera or sold separately)
DV tape
(HDV format)
b page 33
All of the above media
Use an AV cable
(supplied with camera or sold separately)
b page 34
14
Select the copy mode and
create a disc!
One Touch
Copying All Copying and Copying Only Copying
Copying
Visual Index
Lists
Select by a scene/
shooting date
3
Disc Burn
Press the button on
camera
Contents
The entire contents
of camera
Consolidating New Video
Playlist
Only the newcontents Playlist contents on
of camera camera
*
Contents
Consolidate the video
onto one disc
—
4
—
—
—
—
—
—
2
Copying All Contents
The entire contents of camera
Copying Manually
Recording while operating camera
—
*2 Recording only possible when connected to a camera via USB cable. Only some models
support one touch disc burn.
*3 Copying Playlist is possible only with cameras that can create a playlist.
*4 Built-in memory of “HYBRID Plus” Handycam® cannot be recorded by One Touch Disc Burn.
15
Videos
Type of copy mode
Record SD (Standard Definition) video as is
What is the recording
media?
Connection and setup
Use a USB cable
(supplied with camera or sold
separately)
HDD
b page 31
Use a USB cable
(supplied with camera or sold
separately)
b page 31
Built-in memory
8cm Disc
Use a USB cable
(supplied with camera or sold
separately)
b page 31
Insert a Memory Card into
1
the slot*
Memory Card
b page 36
*
1 You can record video by connecting a
camera via a USB cable.
Use a DV (i.LINK) cable
(sold separately)
DV tape
D8 (Digital8) tape
b page 33
Use an AV cable
(supplied with camera or sold separately)
All of the above media
Other media
(8mm tape, MICROMV tape, etc.)
b page 34
16
Select the copy mode and
create a disc!
One Touch
Disc Burn
Copying All Copying and Copying Only Copying
Contents Consolidating New Video Playlist
Only the newcontents Playlist contents on
of camera of camera camera
Copying
Visual Index
Lists
Select by a scene/
shooting date
Press the button on The entire contents
Contents
camera
Consolidate the video
onto one disc
—
—
—
2
—
—
—
—
—
Copying All Contents
The entire contents of camera
Copying Manually
Recording while operating the camera
—
*2 Built-in memory of “HYBRID Plus” Handycam® cannot be recorded by One Touch Disc Burn.
17
Videos
Type of copy mode
Connect other video device and record SD
(Standard Definition) video
What is the recording
media of your video
device?
Connection and setup for
your video device
You cannot record via a USB cable.
Use a DV (i.LINK) cable
Video device with DV
connector, capable of
outputting DV signals
(sold separately)
b page 33
Use an AV cable
(supplied with DVDirect or sold
separately)
Video device with AV OUT
b page 34
18
Photos
Copying a photo
Photos are recorded as a JPEG file. You can create a slideshow of the disc contents.
What is the recording
Connection and setup
media or memory card?
Recording media
HDD
Use a USB cable
(supplied with camera or sold
separately)
Built-in memory
8cm Disc
b page 31
Memory Card
Memory card
Insert a Memory card into
the slot
“Memory Stick Duo”
“Memory Stick”
SD Card
b page 36
xD Picture Card
20
Select the copy mode and
create a disc!
The created disc
Copying All
Copying Visual
Contents
The entire contents
of camera
Index Lists
Select by a scene/
shooting date
Photo disc
• The photo (JPEG file) is copied.
JPEG
Playable on a computer or DVD player/
recorder capable of playing JPEG files.
Copying All
Copying Visual
Slideshow disc
Contents
The entire contents
of camera
Index Lists
Select by a scene/
shooting date
• The photo (JPEG file) is copied.
• The slideshow disc (Standard
Definition) is created.
JPEG
Slideshow
Playable on a computer or commercial
DVD player/recorder.
21
Introducing DVDirect
About this manual
pages.
through the recording process.
Videos
m
Configure your device if necessary.
m
Select an available copy mode (A - E) best suited to your needs. Follow the instructions
on the page referred to in this manual.
m
Photos
Determine the connection and device operation then configure your device if necessary.
m
Select an available copy mode best suited to your needs. Follow the instructions on the
page referred to in this manual.
22
Icons
In this manual, section headings have different icons depending on the device or operation.
Use these icons to determine the connection or device operation.
Icon
Meaning
Functions available for camera recording to hard disk
Functions available for camera recording to built-in memory
Functions available for camera recording to 8cm disc
Functions available for camera recording to “Memory Stick
Duo,” SD card, etc.
Functions available for camera recording to DV or D8
(Digital8) tapes
Video device with audio/video outputs
®
About Handycam
®
®
In this manual, Handycam refers to a Sony camcorder. High Definition Handycam refers to
an HD (High Definition) compatible camcorder.
About Images
In this manual, “images” refer to both photos (still images) and videos.
About the DVDirect
In this manual, “DVDirect” refers to the VRD-MC6.
About illustrations
The on-screen display illustrations used in this manual may not match the graphics displayed
on your screen.
23
Features
You can easily record videos or photos using the DVDirect.
Recording HD (High Definition) video
You can record HD (High Definition) videos taken with a Sony digital video camera or digital
still camera. Created discs can be played on an AVCHD compatible device. For details about
AVCHD disc compatibility, see “Notes on HD (High Definition) disc compatibility” on page
81.
Recording SD (Standard Definition) video
You can record video from various cameras and AV devices directly onto discs in SD
(Standard Definition) image quality. Created discs can be played on DVD players and other
DVD devices.
Recording photos
You can archive photos from a memory card, or a connected Sony camera directly onto a disc.
Before you begin
Notes on the supported device and the image
The DVDirect supports the following copying.
• HD (High Definition) video
- High Definition (AVCHD format) video taken by a Sony digital video camera
- High Definition (AVCHD format) video taken by a Sony digital still camera
• SD (Standard Definition) video
- Standard Definition video taken by a Sony digital video camera
- video of various video devices (video device with audio/video output)
24
• Photos
- photos (JPEG format) taken by a digital video camera
- photos (JPEG format) taken by a digital still camera
The ability to copy depends on your device, recording media, type of video/photos or disc
type you are creating. For details, see page 6 and select the corresponding connection and
operation.
Notes on copying on discs
• You cannot copy:
- videos with copy-protection signals (commercial DVDs, VHS software, some programs
from satellite or CATV receivers, etc.).
- videos to a disc (unfinalized) created with a device other than the DVDirect.
• You cannot record video unsupported by DVDirect via USB or a memory card inserted into
the DVDirect’s slot (for example, MPEG1 or MPEG4, other than AVCHD, etc. taken with a
mobile phone or web-camcorder). You can record video using A/V cable.
• You cannot copy the following HD (High Definition) videos to the disc as is. These HD
(High Definition) videos can be copied by down-converting to SD (Standard Definition)
quality:
- HD videos recorded in REC mode at a bit rate exceeding 18Mbps, such as in [HD FX]
®
mode (for example, High Definition Handycam ) in AVCHD format.
®
- HD videos recorded on an 8cm DVD using a High Definition Handycam .
®
- HD videos recorded on a DV tape using a High Definition Handycam (HDV format).
- HD videos recorded with an HD (High Definition) compatible camera other than
AVCHD format
1
• You cannot simultaneously copy images when storing multiple types of image* on a
camera or memory card.
• You cannot simultaneously copy images stored in different media in case of multiple types
2
of media* on a camera or memory card.
• If you erase or edit a video on a camera with a computer or Playstation 3 , you may not be
®
able to copy videos properly by connecting the camera to the DVDirect. Use the camera to
erase or edit video.
*
1 HD (High Definition) video, SD (Standard Definition) video or photo
*2 HDD, built-in memory, 8cm disc or “Memory Stick Duo”
25
Package Contents
Please confirm that the package contains the following items.
If any of these items are missing or damaged, please contact your dealer.
The number in parentheses indicates the number of items.
VRD-MC6 (DVDirect) (1)
AC adapter (1)
AC power cord (1)
Operating Instructions (this document) (1)
b Note
• Use an AC power cord appropriate to the region or country of use.
26
Parts and Controls
Main unit
Front and sides
R
AUDIO IN
1
L
VIDEO IN
2
0
DV IN
3
qa
qs
4
5 6 7 8 9
b Note
• “Memory Stick Duo” uses a different slot from
other memory cards. Make sure to insert a
“Memory Stick Duo” into the “Memory Stick
Duo” slot, and other types of memory cards into
the multi memory card slot. If you try to insert a
“Memory Stick Duo” into the multi memory
card slot, it may become jammed.
H Emergency eject hole
If you cannot open the disc tray with the
Z (eject) button, turn off the DVDirect.
Insert a pin or straightened paper clip
into this hole to open the disc tray.
Do not insert this
in this slot.
Insert a “Memory Stick,” SD Card or
xD-Picture Card here.
“Memory Stick Duo”
K Memory card access LED
Lights amber when accessing a memory
card.
27
Top panel
1
R
AUDIO IN
L
VIDEO IN
DV IN
2
3
RETURN
ENTER
4
5
A Display window
Displays the operation screen, and
images from a playback device or
memory card.
B V/v/B/b cursor / ENTER button (pages
Rear panel
DC IN 12V
1
b Note
• Metallic parts, such as terminals, etc., may
become warm after the DVDirect is used. This
is not a malfunction.
28
Preparations for Recording
Turning the Power On
1
2
3
Connect the supplied AC power cord to the AC adapter.
Insert the power plug of the AC adapter into the DVDirect’s DC IN connector.
Insert the power plug of the AC power cord into a power outlet.
DVDirect
To DC IN
connector
DC IN 12V
AC adapter
AC power cord
To power outlet
b Notes
• Be sure to use the supplied AC power cord and the AC adapter.
• Do not use damaged cables, such as cables with deformed connectors.
4
Press the 1 (power) button.
After the display window lights and the DVDirect logo appears, the on-condition screen
appears.
29
Inserting a Disc
1
Press the Z (eject) button.
The disc tray ejects.
The disc tray opens halfway. Open it fully by hand.
2
Place the disc in the disc tray with its recording side down, and push the
disc tray in the direction of the arrow.
b Note
• Do not touch the recording side of the disc.
Push the disc until it clicks into place.
Push the disc tray in until it clicks fully closed.
b Note
• Metallic parts of the disc tray and an ejected disc may be warm. This is not a malfunction.
30
Connecting Cables for Recording
®
For types of connection and settings, see the “Connection and setup for your Handycam /
USB cable
1
Turn on the camera.
b Note
• For the camcorder, make sure that the AC power cord is connected to the AC adapter.
z Hint
• Depending on the model type, you may need to change the mode from the REC mode to other modes such
as PLAY or EDIT. For details about modes, refer to your camera’s operating instructions.
2
Connect the camera to the DVDirect.
Multi port
USB cable/USB cable
for multi-use terminal
(supplied with camera
or sold separately)
USB port
(Type Mini B)
USB port
(Type A)
USB cable
(supplied with camera
or sold separately)
z Hint
• If your camera does not have USB port, use a Handycam® Station or Multi Output Station that supports
your camera.
3
Check the USB connection on the camera.
Sony digital video camera
The [USB SELECT] screen appears. Be sure to select the media that stores images to
record.
31
Button names on the [USB SELECT] screen
Storage Media
Button Name
Hard disk drive
Built-in memory
8cm disc
[
[
[
[
USB CONNECT] [
COMPUTER] [
HDD], etc.
USB CONNECT], etc.
USB CONNECT] [
USB CONNECT] [
COMPUTER], etc.
COMPUTER], etc.
Memory Card
z Hints
• Depending on the model, USB connection may complete simply by connecting the camera to the
DVDirect ([USB mode] screen appears). In this case, selecting the recording media is unnecessary.
• If your camera has a [USB SPEED] setting, specify [AUTO] ([AUTO] is the default setting).
Sony digital still camera
USB connection completes only by connecting the camera to the DVDirect. [USB mode]
or [Mass Storage] screen appears.
z Hints
• If your camera has a [USB Connect] setting, specify [AUTO] or [Mass Storage] ([AUTO] is the
default setting).
• If your camera has a [LUN Settings] setting, you may need to set [Single], depending on the model
(default setting is different depending on the model).
• See the following web site for details on supported camera models (English only):
b Note
• If a camera with built-in memory and memory card is connected to the DVDirect, the DVDirect
will choose the memory card as the USB connection. However, built-in memory might be chosen
depending on the model of the camera and its setting. For details, see the instruction manual of the
camera, and confirm the settings of [USB Connect] and [LUN Settings].
b Notes
• You need an audio/video cable (AV cable), instead of a USB cable, for connection to copy:
– “PhotoMOVIE” from an 8cm disc in a Handycam®.
– videos from an 8cm disc formatted in VR mode in a Handycam®.
32
DV (i.LINK) cable
1
Turn on the camera.
b Note
• For the camera, make sure that the AC power cord is connected to the AC adapter.
2
3
Set the camera to playback mode.
• Playback operation differs among cameras. For most cameras, switch the power/mode button to
playback, PLAY/EDIT or VTR mode to play video. For details, refer to the operating instructions of
your camera.
• When you copy HD (High Definition) videos using High Definition Handycam® (HDV format) by
connecting with DV (i.LINK) cable, set the [i.LINK CONV] setting on the Handycam® to [ON]. This
will down-convert videos recorded in HD (High Definition) to SD (Standard Definition) quality.
Connect the camera to the DVDirect.
DV connector
DV IN connector
DV (i.LINK) cable (not supplied)
b Notes
• A DV (i.LINK) cable is for DV or D8 (Digital8) tapes only. You cannot record videos from MICROMV
or HDV cameras (HDV format) and other digital video devices having an i.LINK connector. You need an
audio/video cable (AV cable) for these devices.
• The following models do not support for recording with a DV (i.LINK) cable. Use an audio/video cable.
– DCR-VX700/VX1000, HDR-FX1/FX7/FX1000
33
Audio/video cable (AV cable)
1
Turn on the video device.
b Note
• For the camera, make sure that the AC power cord is connected to the AC adapter.
2
3
Operate the video device to start playback of video.
• Playback operation differs among video devices. For most cameras, switch the power/mode button to
playback, PLAY/EDIT or VTR mode to play video or perform recording. Cameras with multiple
media require specifying the media (HDD, “Memory Stick Duo,” 8cm disc, or Built-in memory). For
details, refer to the operating instructions of your video device.
• The [A/V t DV OUT] setting on Handycam® (DV/D8) must be set to [OFF] ([OFF] is the default
setting).
Connect the video device to the DVDirect.
Use an audio/video cable (not supplied) or AV cable (not supplied) when connecting a
video device to the DVDirect.
z Hint
• Connectors may differ between devices. Refer to the operating instructions for your device, and use an
appropriate cable.
For audio/video cables:
To AUDIO/VIDEO OUT
connectors
AUDIO IN connectors
VIDEO IN connector
Audio/video cable (not supplied)
34
A/V OUT connector
A/V
A/V OUT
or
AUDIO IN connectors
VIDEO IN connector
AV cable (not supplied or supplied with the video device)
35
Memory Card
When copying videos or photos from a memory card, insert the memory card into its
corresponding memory card slot on the DVDirect.
Insert a memory card into its corresponding slot.
“Memory Stick Duo”
“Memory Stick”
SD Card
xD-Picture Card
Push the memory card into the slot until you hear a click. To remove, push the card and pull
out.
b Notes
• Do not use more than one memory card slot at a time. Insert only one memory card into a memory card
slot.
• Do not insert another memory card while recording onto a disc. Doing so may cause a write error.
• Do not insert a “Memory Stick Duo” with a “Memory Stick Duo” adapter into the multi memory card slot.
• Never remove the memory card while the memory card access LED is lit. Otherwise data in the memory
card may be damaged.
• An ejected memory card may be warm. This is not a malfunction.
36
About operation of DVDirect
After the power is turned on, the DVDirect automatically detects inserted memory cards,
discs, and input signals from connected devices. A message indicating how to prepare for
recording then appears in the display window. By this message, you can automatically move
on to the recording procedure you intended without complicated button operations.
The [Menu] display appears when the RETURN button is pressed after the power is turned on.
You can perform recording procedures manually by selecting options from the menu. The
menu items are as follows.
,
Menu
Function
Video b DVD
Photo b DVD
DVD Preview
AVCHD Dubbing
Setup
Copy a SD (Standard Definition) video to a disc.
Copy photos to a disc.
Playback a created disc.
Record HD (High Definition) video to a disc.
Configure various settings.
Notes on copying multiple types of image
When multiple image types are recorded in a camera or memory card the image is copied as
follows in this manual.
(Images are copied in the following order: HD (High Definition) video - SD (Standard
Definition) video - photo.)
Types of image recorded in camera/memory card
Type of image to be copied
HD (High
SD (Standard
Photo
Definition) video Definition) video
a
a
a
a
a
a
HD (High Definition) video
HD (High Definition) video
HD (High Definition) video
SD (Standard Definition) video
a
a
a
To copy SD (Standard Definition) video, use [Video b DVD] in the [Menu] screen. To copy a
photo, use [Photo b DVD] in the [Menu] screen.
37
Copying From a camera
Copying All Contents
This mode allows you to record videos onto
a disc from a camera connected to the
DVDirect or memory card inserted into the
2
Make sure that [Full] appears at
the top right of the display
window, and press the
slot with a single touch of the
(record)
button. This is one of the simpler copy
modes, eliminating the need to select
videos.
(record) button to start recording.
b Note
• See “Notes on copying on discs” on page 25
previously.
The DVDirect starts the recording
process. The
up during recording. The following
appears in the display window.
(record) button lights
1
Confirm the message in the
display window.
When the DVDirect detects signals
from a camera connected to the USB
port or memory card inserted into the
slot, [USB] or the type of memory card
appears in the top left of the display
window.
The following appears in the display
window when a camcorder is connected
to the USB port.
Type of disc created
: HD (High
Definition) video
: SD (Standard
Definition) video
Type
of input
Copy
mode
Number of required discs
38
3
Change to a blank disc when the
message [Insert a blank DVD.]
appears.
If the contents do not fit onto a single
disc, the disc will be ejected
automatically when it becomes full.
Remove the created disc and insert a
blank one. Recording will resume
automatically.
Next disc/number of
required discs
4
Remove the created disc.
The disc is finalized automatically when
recording is complete.
To stop recording
Press the
(stop) button when
replacing a disc.
You cannot stop while recording is in
progress.
39
Copying Only New Video
You can copy only newly-recorded
contents whose previous contents have
already been recorded onto a disc (by
selecting [Incremental] or One Touch Disc
Burn). As the DVDirect automatically
detects newly recorded videos, you do not
need to search for them yourself.
2
Press B or b to select
[Incremental], and press the
(record) button to start recording.
b Note
• See “Notes on copying on discs” on page 25
previously.
1
Confirm the message in the
display window.
When the DVDirect detects signals
from a camera connected to the USB
port or memory card inserted into the
slot, [USB] or the type of memory card
appears in the top left of the display
window.
The DVDirect starts the recording
process. The
(record) button lights
The following appears in the display
window when a camcorder is connected
to the USB port.
up during recording. The following
appears in the display window.
Type of disc created
: HD (High
Definition) video
: SD (Standard
Definition) video
Type
of input
Copy
mode
Number of required discs
40
3
Change to a blank disc when the
message [Insert a blank DVD.]
appears.
If the contents do not fit onto a single
disc, the disc will be ejected
automatically when it becomes full.
Remove the created disc and insert a
blank one. Recording will resume
automatically.
z Hint
• To finalize a disc means to make the disc
playable on other DVD devices. For details
about finalizing, refer to [Finalize disc] on page
68.
6
Press V or v to select [OK] and
press the ENTER button.
Next disc/number of
required discs
4
5
Press the Z (eject) button to eject
the disc when recording is
complete.
If you copy HD (High Definition)
videos onto a disc, the disc will be
finalized and ejected automatically. If
you copy SD (Standard Definition)
videos onto a disc, a message asking
whether to finalize the disc appears. Go
to step 5.
When finalizing has completed, the disc
tray opens.
To stop recording
Press the
(stop) button when
replacing a disc.
You cannot stop while recording is in
progress.
To finalize the disc, press V or v
to select [Yes] and press the
ENTER button.
z Hint
• The DVDirect stores the recording history of a
camera (built-in memory), or a memory card,
copying only newly-recorded video (to be
recorded to a disc). The DVDirect can store a
combined total of 10 recording history stored in
a camera or memory card.
If you select [No], the disc will be
ejected without being finalized. You can
skip step 6 below.
41
Copying Playlist
This mode allows you to record videos
within a Playlist created on your camera.
For details on creating a Playlist, refer to
your camera’s operating instructions.
2
Press B or b to select [Playlist],
and press the
(record) button
to start recording.
b Note
• See “Notes on copying on discs” on page 25
previously.
1
Confirm the message in the
display window.
When the DVDirect detects signals
from a camera connected to the USB
port or memory card inserted into the
slot, [USB] or the type of memory card
appears in the top left of the display
window.
The following appears in the display
window when a camcorder is connected
to the USB port.
The DVDirect starts the recording
process. The (record) button lights
up during recording. The following
appears in the display window.
Type of disc created
: HD (High
Definition) video
: SD (Standard
Definition) video
Type
of input
Copy
mode
Number of required discs
42
3
Change to a blank disc when the
message [Insert a blank DVD.]
appears.
If the contents do not fit onto a single
disc, the disc will be ejected
automatically when it becomes full.
Remove the created disc and insert a
blank one. Recording will resume
automatically.
z Hint
• To finalize a disc means to make the disc
playable on other DVD devices. For details
about finalizing, refer to [Finalize disc] on page
68.
6
Press V or v to select [OK] and
press the ENTER button.
Next disc/number of
required discs
4
5
Press the Z (eject) button to eject
the disc when recording is
complete.
If you copy HD (High Definition)
videos onto a disc, the disc will be
finalized and ejected automatically. If
you copy SD (Standard Definition)
videos onto a disc, a message asking
whether to finalize the disc appears. Go
to step 5.
When finalizing has completed, the disc
tray opens.
To stop recording
Press the
(stop) button when
replacing a disc.
You cannot stop while recording is in
progress.
To finalize the disc, press V or v
to select [Yes] and press the
ENTER button.
If you select [No], the disc will be
ejected without being finalized. You can
skip step 6 below.
43
Copying Visual Index Lists
You can record videos selected by viewing
thumbnails.
b Note
• See “Notes on copying on discs” on page 25
previously.
3
4
Press V or v to select [Thumbnail]
or [Shooting Date], and press the
ENTER button.
1
Confirm the message in the
display window.
When the DVDirect detects signals
from a camera connected to the USB
port or memory card inserted into the
slot, [USB] or the type of memory card
appears in the top left of the display
window.
The following appears in the display
window when a camcorder is connected
to the USB port.
Type of disc created
: HD (High
Definition) video
Press B/V/v/b to select the
thumbnail or shooting date you
wish to copy, and press the
ENTER button to mark.
: SD (Standard
Definition) video
Type
of input
Pressing the ENTER button toggles the
selection between marked and
unmarked.
Copy
mode
Selected scene
Number of required discs
Marked
sceneto
copy
2
Press B or b to select [Select
Videos].
Shooting date
44
5
Press the
start recording.
(record) button to
Next disc/number of required
discs
The DVDirect starts the recording
process. The
up during recording. The following
appears in the display window.
(record) button lights
7
8
Press the Z (eject) button to eject
the disc when recording is
complete.
If you copy HD (High Definition)
videos onto a disc, the disc will be
finalized and ejected automatically. If
you copy SD (Standard Definition)
videos onto a disc, a message asking
whether to finalize the disc appears. Go
to step 8.
To finalize the disc, press V or v
to select [Yes] and press the
ENTER button.
6
Change to a blank disc when the
message [Insert a blank DVD.]
appears.
If you select [No], the disc will be
ejected without being finalized. You can
skip step 9 below.
If the contents do not fit onto a single
disc, the disc will be ejected
automatically when it becomes full.
Remove the created disc and insert a
blank one. Recording will resume
automatically.
z Hint
• To finalize a disc means to make the disc
playable on other DVD devices. For details
about finalizing, refer to [Finalize disc] on page
68.
45
9
Press V or v to select [OK] and
press the ENTER button.
When finalizing has completed, the disc
tray opens.
To stop recording
Press the
(stop) button when
replacing a disc.
You cannot stop while recording is in
progress.
46
Copying and Consolidating Contents (from an
8cm disc)
When you have more than one 8cm disc to
copy, you can consolidate and record their
contents onto a single, standard 12cm disc.
b Note
• See “Notes on copying on discs” on page 25
previously.
The DVDirect starts the recording
process. The
(record) button lights
up during recording. The following
appears in the display window.
1
Confirm the message in the
display window.
When the DVDirect detects a signal
from a camera connected to the USB
port, [USB] appears in the top left of the
display window.
Type of input
Copy mode
3
4
Complete recording from one
8cm disc.
If you are copying from another 8cm
disc, replace the 8cm disc in the camera
with the new 8cm disc, and press the
(record) button to continue
recording.
2
Press B or b to select
[Consolidation] and press the
(record) button to start recording.
Press the Z (eject) button to eject
the disc when recording from all
8cm discs is complete.
A message asking whether to finalize
the disc appears.
47
5
To finalize the disc, press V or v
to select [Yes] and press the
ENTER button.
If you select [No], the disc will be
ejected without being finalized. You can
skip step 6 below.
z Hint
• To finalize a disc means to make the disc
playable on other DVD devices. For details
about finalizing, refer to [Finalize disc] on page
6
Press V or v to select [OK] and
press the ENTER button.
When finalizing has completed, the disc
tray opens.
b Note
• You cannot stop while recording is in progress.
48
Copying Manually
This mode allows you to record video on
the DVDirect while controlling playback
manually on the connected camera.
audio/video cable (AV cable) for recording
The video from the connected camera
appears.
z Hint
• When the prompt message [Format disc for DV/
VIDEO recording?] appears after inserting a
blank disc, select [OK]. Formatting a disc may
take several seconds to complete. You cannot
record HD (High Definition) videos onto the
formatted disc under this message.
z Hint
• If all the preparations are complete for copying,
the DVDirect detects a signal from a camcorder
connecting to the VIDEO IN connector, and the
display window in step 4 appears automatically.
You can skip steps 1 to 3.
1
2
Press the RETURN button.
The [Menu] display appears.
Make sure that [Video b DVD] is
selected, and press the ENTER
button.
4
Operate your camera to start
video playback, and press the
(record) button of the DVDirect.
The message [Recording] appears in the
display window, and the
(record)
button lights up during recording. The
following appears in the display
window.
3
Press V or v to select [VIDEO IN]
and press the ENTER button.
49
To pause recording
9
Press V or v to select [OK] and
press the ENTER button.
Press the
(record) button during
recording. To resume recording, press
the
(record) button again.
5
6
7
Press the
recording.
(stop) button to stop
To record an additional video,
repeat steps 4 and 5.
When finalizing has completed, the disc
tray opens.
Press the Z (eject) button to eject
the disc when recording is
complete.
b Notes
• Start recording immediately after inserting a
disc. The recording process may take a few
A message asking whether to finalize
the disc appears.
seconds to start after pressing the
button if the disc was inserted more than 10
minutes prior to starting.
(record)
8
To finalize the disc, press V or v
to select [Yes] and press the
ENTER button.
• When you press the
hear the noise of the disc turning momentarily.
(stop) button, you may
If you select [No], the disc will be
ejected without being finalized. You can
skip step 9.
z Hints
• To finalize a disc means to make the disc
playable on other DVD devices. For details
about finalizing, refer to [Finalize disc] on page
• When using a DVD+RW disc, finalizing is
unnecessary. You can skip steps 8 and 9.
50
One Touch Disc Burn
This mode allows you to record video from
a camera onto a disc by simply pressing
DISC BURN on the camera. You can
record additional video onto a disc that has
been previously recorded on, as with
copying only new videos (page 40).
3
Connect the camera to the
DVDirect.
1
2
Turn on the DVDirect (page 29)
USB port (Type A)
Turn on the camera.
b Note
• Make sure that the AC power cord is connected
to the AC adapter.
USB cable
(Not supplied)
USB port
(Type Mini-B)
The [USB SELECT] screen appears on
the camcorder’s LCD screen.
51
4
Touch DISC BURN on the
camera’s LCD screen, or press
5
Change to a blank disc when the
message [Insert a blank DVD.]
appears.
the DISC BURN (
the camcorder.
) button on
If the contents of the camera do not fit
onto a single disc, the disc will be
ejected automatically when it becomes
full. Remove the created disc and insert
a blank one. Recording will resume
automatically.
Touch [DISC BURN] or
[DVD BURN]
Next disc/number of
required discs
The DVDirect starts the recording
process.
If the camera’s media has both HD
(High Definition) and SD (Standard
Definition) videos:
6
7
Press the Z (eject) button to eject
the disc when recording is
complete.
HD (High Definition) videos are
If you copy HD (High Definition)
videos onto a disc, the disc will be
finalized and ejected automatically. If
you copy SD (Standard Definition)
videos onto a disc, a message asking
whether to finalize the disc appears. Go
straight to step 7.
b Notes
• Depending on the camera, the display that
appears on the camera’s LCD screen or button
names on the camcorder may differ. (e.g. DVD
BURN)
• In One Touch Disc Burn mode, you can record
videos from an attached video camera; however,
depending on the camera, the recordable media
may vary. For example, in the case of a
To finalize the disc, press V or v
to select [Yes] and press the
ENTER button.
Handycam® containing both HDD and memory
card media, only the HDD content can be
recorded by One Touch Disc Burn.
If you select [No], the disc will be
ejected without being finalized. You can
skip step 8 below.
• The DUBBING button of “HYBRID Plus”
Handycam® does not work in the same manner
as the DISC BURN button. Pressing the
DUBBING button does not start recording with
the DVDirect.
52
z Hint
• To finalize a disc means to make the disc
playable on other DVD devices. For details
about finalizing, refer to [Finalize disc] on page
8
Press V or v to select [OK] and
press the ENTER button.
When finalizing has completed, the disc
tray opens.
To stop recording
Press the
(stop) button when
replacing a disc.
You cannot stop while recording is in
progress.
53
Copying From Video Devices
Copying All Contents
This mode allows you to record the entire
video tape content onto a disc. The
DVDirect automatically controls playback
on the connected video device.
(i.LINK) cable for recording (page 33).
4
Confirm the message in the
display window.
When the DVDirect detects a signal
from a camera connected to the DV IN
connector, [DV] appears in the top left
of the display window.
z Hint
Type of input
Copy mode
• If all the preparations are complete for copying,
the DVDirect detects a signal from a camcorder
connecting to the DV IN connector, and the
display window in step 4 appears automatically.
You can skip steps 1 to 3.
1
2
Press the RETURN button.
The [Menu] display appears.
Make sure that [Video b DVD] is
selected, and press the ENTER
button.
5
Make sure that [Full] appears at
the top right of the display
window, and press the
(record) button to start recording.
The DVDirect starts recording at the
same time the video device starts
playback. If the video tape is not at its
beginning, it will automatically rewind
and the DVDirect will start recording.
During recording, the message
3
Press V or v to select [DV IN] and
press the ENTER button.
[Recording] appears in the display
window, and the
(record) button
lights up. The following appears in the
display window.
54
To pause recording
Press the
(record) button during
recording. To resume recording, press
the
(record) button again.
To stop recording
Press the
(stop) button, and then
press the RETURN button. The
DVDirect stops recording and returns to
the display window in step 4.
6
Remove the created disc.
The disc is finalized automatically when
recording is complete.
z Hint
• Recording automatically stops after a blank
portion over 2 minutes, or when the end of the
DV tape is reached.
55
Copying Manually
This mode allows you to record video on
the DVDirect while controlling playback
manually on the connected video device.
z Hint
• If all the preparations are complete for copying,
the DVDirect detects a signal from a video
device connecting to the VIDEO IN or DV IN
connector, and the display window in step 4
appears automatically. You can skip steps 1 to
3.
4
Make sure that the video device is
correctly connected to the
DVDirect.
For connection with DV (i.LINK)
cable:
1
2
Press the RETURN button.
The [Menu] display appears.
[DV] appears in the top left of the
display window, and the copy mode
appears at the top right of the display
window. Press B or b to select
[Manual].
Make sure that [Video b DVD] is
selected, and press the ENTER
button.
Type of input
Copy mode
3
Press V or v to select the input
connected to the video device
and press the ENTER button.
For connection with A/V cables:
[VIDEO] appears in the top left of the
display window. Go to step 5.
When connecting to the video device
with the DV (i.LINK) cable, select [DV
IN]. When connecting to the video
device with the A/V cable, select
[VIDEO IN].
56
z Hint
• When the prompt message [Format disc for DV/
VIDEO recording?] appears after inserting a
blank disc, select [OK]. Formatting a disc may
take several seconds to complete. You cannot
record HD (High Definition) videos onto a
formatted disc under this message.
To pause recording
Press the
(record) button during
recording. To resume recording, press
the
(record) button again.
z Hint
• The DVDirect starts and stops recording
automatically as it detects video input signals
from a connected video device. For example:
5
Operate the video device to start
playback, and press the
(record) button of the DVDirect to
start recording.
– When you press the
(record) button
before the connected video device starts
playing, the DVDirect pauses. When the
video device starts playing back, the
DVDirect automatically starts recording
video.
– If you stop playback on the video device
during recording, video signal is interrupted
and the DVDirect pauses recording. If you
resume playback on the video device, the
DVDirect resumes recording.
When the DVDirect waits a video signal to
resume recording, the message [Waiting for
input signal.] appears in the DVDirect’s display
window. If no video signal is detected for 2
minutes, the DVDirect stops recording. (As
video devices always output video signals from
their operation screen or TV screen other than
playback, some video devices may not operate
as above.)
6
7
Press the
recording.
(stop) button to stop
During recording, the message
[Recording] appears in the display
window, and the
(record) button
lights up. The following appears in the
display window.
To record an additional video,
repeat steps 5 and 6.
57
b Notes
8
9
Press the Z (eject) button to eject
the disc when recording is
complete.
• Start recording immediately after inserting a
disc. The recording process may take a few
seconds to start after pressing the
button if the disc was inserted more than 10
minutes prior to starting.
(record)
• When you press the
(stop) button, you may
To finalize the disc, press V or v
to select [Yes] and press the
ENTER button.
hear the noise of the disc turning momentarily.
If you select [No] and press b, the disc
will be ejected without being finalized.
You can skip step 10 below.
z Hint
• To finalize a disc means to make the disc
playable on other DVD devices. For details
about finalizing, refer to [Finalize disc] on page
10
Press V or v to select [OK] and
press the ENTER button.
When finalizing has completed, the
disc tray opens.
58
Copying Photos
Copying All Contents
This mode allows you to record photos onto
a disc from a camera connected to the
DVDirect, or a memory card inserted into
any of memory card slots, with a single
2
Make sure that [Full] appears at
the top right of the display
window, and press the
touch of the
(record) button. This is one
(record) button to start recording.
of the simpler copy modes, eliminating the
need to select photos stored on your camera
or memory card.
The DVDirect starts the recording
1
Confirm the message in the
display window.
process. The
(record) button lights
up during recording. The following
appears in the display window.
When the DVDirect detects a signal
from a camera connected to the USB
port or a memory card inserted into any
of the memory card slots, [USB] or the
type of memory card appears in the top
left of the display window.
The following appears in the display
window when a camcorder is connected
to the USB port.
Type of input
Copy mode
3
4
Press the Z (eject) button to eject
the disc when recording is
complete.
A message asking whether to finalize
the disc appears. Go to step 4. If
[Slideshow Creation] is set to [ON], the
disc is finalized automatically when
creation of the slideshow is complete,
and the disc tray opens. You can skip
steps 4 to 6.
To finalize the disc, press V or v
to select [Yes] and press the
ENTER button.
59
If you select [No], the disc will be
ejected without being finalized. You can
skip steps 5 and 6.
When finalizing has completed, the disc
tray opens.
z Hints
z Hint
• When creating the slideshow, both photos
(JPEG files) and slideshow with SD (Standard
Definition) picture quality are copied onto the
disc.
• It takes some time to complete finalizing for the
slideshow disc. The amount of time it takes to
complete the slideshow disc depends on the
number and size of the photos (for example, it
may take 20 minutes or more to record 50 files
(6-megapixel photos) onto a disc).
• To finalize a disc means to make the disc
playable on other DVD devices. For details
about finalizing, refer to [Finalize disc] on page
5
Press V or v to select [OK] and
press the ENTER button.
6
To create the slideshow, press V
or v to select [Yes] and press the
ENTER button.
If you select [No], the slideshow will
not be created.
60
Copying Visual Index Lists
You can record photos selected by viewing
thumbnails.
3
Press V or v to select [Thumbnail]
or [Shooting Date] and press the
ENTER button.
1
Confirm the message in the
display window.
When the DVDirect detects a signal
from a camera connected to the USB
port or a memory card inserted into any
of the memory card slots, [USB] or the
type of memory card appears in the top
left of the display window.
The following appears in the display
window when a camcorder is connected
to the USB port.
4
Press B/V/v/b to select the
viewing thumbnail or shooting
date you want to copy and press
the ENTER button to mark.
Type of memory card Copy mode
Pressing the ENTER button toggles the
selection between marked and
unmarked.
Current photo/Number Marked
of recorded photos
photo to copy
2
Press B or b to select [Select
Photos].
Shooting date
z Hint
• If you press the
(stop) button when
thumbnails are displayed, the photo selected
will be displayed in full. The photo can be
rotated 90 degrees right with each press of b.
The photo can be rotated 90 degrees left with
each press of B.
61
5
Press the
start recording.
(record) button to
z Hint
• To finalize a disc means to make the disc
playable on other DVD devices. For details
about finalizing, refer to [Finalize disc] on page
The DVDirect starts the recording
process. The
(record) button lights
up during recording. The following
appears in the display window.
8
Press V or v to select [OK] and
press the ENTER button.
6
Press the Z (eject) button to eject
the disc when recording is
complete.
9
To create the slideshow, press V
or v to select [Yes] and press the
ENTER button.
A message asking whether to finalize
the disc appears. Go to step 7. If
[Slideshow Creation] is set to [ON], the
disc is finalized automatically when
creation of the slideshow is complete,
and the disc tray opens. You can skip
step 7 to 9.
If you select [No], the slideshow will
not be created.
7
To finalize the disc, press V or v
to select [Yes] and press the
ENTER button.
If you select [No], the disc will be
ejected without being finalized. You can
skip steps 8 and 9.
When finalizing has completed, the disc
tray opens.
62
z Hints
• When creating the slideshow, both photos
(JPEG files) and slideshow with SD (Standard
Definition) picture quality are copied onto the
disc.
• It takes some time to complete finalizing for the
slideshow disc. The amount of time it takes to
complete the slideshow disc depends on the
number and size of the photos (for example, it
may take 20 minutes or more to record 50 files
(6-megapixel photos) onto a disc).
63
Previewing in the display window
Previewing Videos
You can play back only discs created with
the DVDirect.
4
Press V/v/B/b to select the title
you want to preview, and press
the ENTER button.
b Notes
• You cannot play back discs created with a video
device other than the DVDirect. The DVDirect
does not support playback of commercial DVDs
or contents on a memory card inserted to the
DVDirect.
Selected
title
• When you preview a video, there is no sound.
• You cannot output videos to an external device,
such as a TV.
• You cannot play back HD (High Definition)
disc.
01/04
The DVDirect starts playback.
1
Turn on the DVDirect and insert a
disc created with the DVDirect.
Operations during playback
z Hint
Button
Operation
• If you insert a finalized disc after turning on the
DVDirect, playback will start automatically (or
the DVD Menu will appear). You can skip steps
2 and 3.
Stop playback
Display the previous or
the next title
B/b
Return to the DVD Menu
or [Menu] display
RETURN
2
3
Press the RETURN button.
The [Menu] display appears.
Press V or v to select [DVD
Preview], and press the ENTER
button.
Playback starts automatically when an
unfinalized disc is inserted.
When playing back a finalized disc, go to
step 4.
64
Previewing Photos
You can play back only discs created with
the DVDirect.
4
Press V or v to select [Photo
Slideshow], and press the ENTER
button.
b Notes
• You cannot play back discs created with a video
device other than the DVDirect. The DVDirect
does not support playback of commercial DVDs
or contents on a memory card inserted to the
DVDirect.
• When you preview a video, there is no sound.
• You cannot output videos to an external device,
such as a TV.
1
Turn on the DVDirect and insert a
disc created with the DVDirect.
The DVD Menu appears. When you
select a title and press the ENTER
button, photos within the title are
automatically played in rotation.
To display the selected photos, select
[Original Photos].
z Hint
• If you insert a finalized disc after turning on the
DVDirect, playback will start automatically (or,
photos or the DVD Menu will appear). You can
skip steps 2 and 3.
Operations during playback
Photo display (Original Photos)
2
3
Press the RETURN button.
The [Menu] display appears.
Button
Function
Display the next or the
previous photo
V/v
Press V or v to select [DVD
Preview], and press the ENTER
button.
/
Return to the [Menu]
display
RETURN
Photo Slideshow
Button
Function
Display the previous or
the next title
B/b
/
Return to the DVD Menu
RETURN
Photos appear when a disc without
creating slideshow or an unfinalized
disc is inserted. When a slideshow disc
is inserted, the prompt message [Photo
preview options] appears. Go to step 4.
65
Setup
Using the Setup Menu
You can change the various settings for
creating discs in the Setup Menu screen.
c HQ
Highest image quality
HSP
High image quality
1
2
Turn on the DVDirect and press
the RETURN button.
SP
Standard image quality
The [Menu] display appears.
LP
Lower image than Standard image quality
Press V or v to select [Setup], and
press the ENTER button.
SLP
Low image quality. You can record more
videos on a disc.
z Hint
• Disc recording capacity depends on the REC
Auto Stop Timer
Select the preset time used to stop recording
automatically when recording in SD
(Standard Definition) quality.
Auto Stop Timer is available when you use
the VIDEO IN connector to connect your
video device.
3
Press V or v to select a menu item
to confirm or change, and press
the ENTER button.
c OFF
Recording does not stop automatically.
30 minutes - 8 hours
Recording automatically stops when the
preset time has passed after recording
starts. Select 30 min, 60 min, 90 min, 2h,
3h, 4h, 6h or 8h.
b Note
• The Auto Stop Timer setting is canceled when:
– the recording is completed,
c indicates the default settings.
– the
recording, or
– the power is turned off.
(stop) button is pressed during
Rec Quality (REC mode)
Select the recording quality for recording in
SD (Standard Definition) quality.
These options are available when you use
the DV IN connector or VIDEO IN
connector to connect your video device.
66
Auto Chapter
Slideshow Music
Specify the time interval at which chapters
are created automatically on an SD
(Standard Definition) disc.
Auto Chapter is available when you use the
DV IN connector or VIDEO IN connector
to connect your video device.
Select whether to record background music
onto a slideshow disc.
OFF
No background music is recorded.
c ON
Background music is recorded.
OFF
No chapters are inserted.
MP3
Sets your favorite music (MP3 file) for
background music. Insert the memory card
with the selected music (MP3 file) into the
DVDirect’s memory card slot before
creating a disc.
c 5 minutes
Inserts chapters at approximately 5-minute
intervals.
10 minutes
Inserts chapters at approximately 10-
minute intervals.
b Notes
• Save only a single music (MP3 file) in the top
directory of a memory card. If there are many
files in the top directory of the memory card, the
desired music may not be set as the background
music.
15 minutes
Inserts chapters at approximately 15-
minute intervals.
• When you hand the created slideshow disc to
others, ensure that any background music is not
copyrighted.
• Some MP3 files may not be applied to the
background music.
DVD Menu
Select a background image to apply to the
DVD Menu screen for discs created with
the DVDirect.
c A, B, C, D
Select from four images. The background
Slideshow Creation
Select whether to create a slideshow
automatically after recording photos onto a
disc.
image is set to [A] by default.
JPEG
Sets your favorite photo (JPEG file) for a
background image. Insert the memory card
with the selected photo (JPEG file) into the
DVDirect’s memory card slot before
creating a disc.
c OFF
A slideshow is not created automatically.
When you press the Z (eject) button after
recording, a message asking whether to
create a slideshow always appears in the
display window.
b Notes
• Save only a single photo (JPEG file) in the top
directory of a memory card. If there are many
photos in the top directory of the memory card,
the desired photo may not be set for the DVD
Menu.
ON
A slideshow is created and the disc is
finalized automatically after recording.
The disc can be played back on a DVD
player immediately.
• Some photos (JPEG files) may not be applied to
the DVD Menu.
67
3 Press V or v to select [OK] and press
Finalize disc
the ENTER button.
If you eject a disc without finalizing, you
can finalize it later.
z Hints
• To finalize a disc means to make the disc
playable on other DVD devices. If you do not
finalize the disc with the DVDirect, the disc
cannot be played on other DVD devices.
• You cannot add videos or photos to a finalized
disc.
The DVDirect starts finalizing the disc.
• When using a DVD+RW disc and connecting
the camcorder to the DVDirect’s VIDEO IN
connector or DV IN connector for recording
video, finalizing is unnecessary. You can always
add videos on the DVD+RW with the
DVDirect, and the disc will be playable on other
DVD devices.
If you insert a disc containing photos,
the message [Create a slideshow?]
appears. To create a slideshow, press V
or v to select [Yes] and press the
ENTER button.
When the message [Complete] appears,
finalizing has completed.
1 Insert a disc to finalize, press V or v
to select [Finalize disc], and press the
ENTER button.
b Note
• It takes a few minutes to finalize a disc.
(Depending on the contents of a disc, time to
complete finalizing a disc may vary. If you
create a slideshow, it takes longer to finalize the
disc.)
Erase disc
You can erase all content recorded on a
DVD+RW or DVD-RW disc. The erased
disc is reusable as a blank disc.
2 Press V or v to select [Yes] and press
the ENTER button.
b Note
• Be aware that this operation erases all data.
1 Insert a disc to erase, press V or v to
select [Erase disc], and press the
ENTER button.
68
z Hint
• The system software is the built-in software that
makes the DVDirect work.
Auto Shut Off
The unit is automatically turned off when
no button operation is made for more than 2
hours.
2 Press V or v to select [Yes] and press
OFF
the ENTER button.
The unit is not automatically turned off.
ON
The unit is automatically turned off.
Demo
The DVDirect automatically plays a demo
when it is not operated for a set period of
time.
3 Press V or v to select [Yes] and press
OFF
the ENTER button.
Disables the demo.
c ON
Enables the demo.
Color System
Set the appropriate color system for the
connected video device.
NTSC
Select this when you connect a video
device of NTSC color system.
The DVDirect starts erasing the disc.
When the message [Complete] appears,
erasing has completed.
PAL
Select this when you connect a video
device of PAL color system.
System Info
b Notes
You can check the system software version
of the DVDirect.
Select [System Info] to view the version of
system software.
• Do not change the setting of the color system
unless it is necessary to do so. The appropriate
color system is preset, or the setting may not be
changeable depending on the country or region
of use.
69
• You cannot record to a disc if the DVDirect’s
color system is different from the color system
of the connected camcorder.
• A disc will not be playable, if the DVDirect’s
color system setting used for recording is
different from the playback device.
Language
Select the language for the display window.
70
Troubleshooting/References
Troubleshooting
If you experience any of the following
difficulties while using the DVDirect, use
this troubleshooting guide to help remedy
the problem before requesting repairs.
Refer also to the operating instructions of
your camera or video devices.
Connection and operation
The camera is connected with a USB
cable, but the DVDirect does not
work.
• Make sure that your camera is supported by
the DVDirect.
• Make sure that the camera is configured for
USB connection correctly and the USB
cable is connected properly to the camera
• Disconnect the USB cable from the
DVDirect. Turn both the camera and the
DVDirect off, then on again.
• If you select the connector from [Menu],
select [USB] of [AVCHD dubbing] in
[Menu] when recording an HD (High
Definition) video. When recording an SD
(Standard Definition) video, select [USB]
of [Video b DVD] in [Menu].
• If you follow the prompt message in the
display window, the DVDirect is
automatically operated by the image quality
(HD (High Definition) video or SD
(Standard Definition) video) stored in the
camera. Follow the message shown in the
display window.
General
To create an SD (Standard
Definition) video disc by down-
converting an HD (High Definition)
video
• Connect a camera to the DVDirect using an
You cannot use a USB cable for
connection.
To change the input
• The DVDirect automatically detects input
signals from connected devices and selects
the input jack. Turn on connected devices
and set up to record videos.
• To change the input manually, select the
input connector from [Menu].
• When recording an HD (High Definition)
video, select [USB] or [Memory card] of
[AVCHD Dubbing] in [Menu]. When
recording an SD (Standard Definition)
video, select [VIDEO IN], [DV IN], [USB],
or [Memory card] of [Video b DVD] in
[Menu].
The camera is connected with a DV
(i.LINK) cable, but the DVDirect does
not work.
• Make sure that the camera is set to the
PLAY/EDIT mode. If it is in the CAMERA
mode, you cannot copy videos with the
DVDirect (page 33).
Power
• Disconnect the DV (i.LINK) cable from the
DVDirect. Turn both the camera and the
DVDirect off, then on again.
The DVDirect does not turn on.
• Make sure that the AC power cord is
• Unplug the power cable and disconnect the
video device from the DVDirect. Remove
the memory card. Then, reconnect the
video device to the DVDirect (or insert the
memory card again) and turn it on.
A video device is connected to
VIDEO IN of the DVDirect, but
playback displays no video on the
DVDirect’s display window.
71
• Make sure that the audio/video cable is
connected properly to A/V OUT of the
video device.
Other video devices do not playback
the created HD (High Definition) disc.
• A generic DVD player cannot playback HD
(High Definition) discs. You need an
AVCHD-compatible player (e.g., Blu-ray
Disc player/recorder) to playback HD discs
• The DVDirect is not detecting input signals
from the connected video device. Turn on
the video device, and configure or operate
it to start playback.
• Make sure that a correct input type is
selected. Select [VIDEO IN] of [Video b
DVD] in [Menu].
Other video devices do not playback
the created photo disc.
The number of discs required does
not appear on the screen when
recording.
• You need a video device capable of playing
JPEG files.
• If many videos are recorded, display may
take some time.
When playing a slideshow disc,
picture noise appears.
• The picture quality of the photos played
back in a slideshow is equivalent to that of
video discs. Using a DVD player capable of
playing JPEG files, higher quality photos
can be played.
A disc inserted in the DVDirect can
be heard spinning momentarily.
• The DVDirect checks the disc and performs
a read operation. This is not a malfunction.
Messages
“
” appears on images in Copying
Visual Index Lists mode.
Unusable disc inserted. Insert a
compatible disc.
• You cannot record the image to which
“
” is displayed.
• An incompatible disc is inserted. Insert a
Playback
• DVD-RW or DVD+RW discs recorded on
other video devices are not supported.
Erase videos or photos recorded on a disc
with [Erase disc] of [Setup] in [Menu]. The
erased disc is reusable as a blank disc (page
68).
Other video devices do not play back
a created SD (Standard Definition)
disc.
• The disc may not be finalized. Use the
DVDirect and finalize the disc first (page
68).
• Some video devices may not work properly
with certain created disc types.
• Your video device may not support the disc
type (e.g., DVD+R, DVD+RW, DVD+R
DL). Check if your video device supports
the disc type.
• You need a CPRM-enabled player to play
back CPRM-compatible DVD-RW and
DVD-R discs.
No input signal.
• Connector may not be selected correctly.
Select input connection to a video device
with [Video b DVD] in [Menu].
• The DVDirect cannot detect input signals
from connected devices. Turn on the
connected video device. Operate the video
device to start video playback.
72
• Check that the DVDirect is correctly
connected to the output on the video
device.
• Disconnect all cables. Turn the DVDirect
and video device off, then on again.
Reconnect the video device to the
DVDirect.
• When storing only HD (High Definition)
video in a Handycam , [Video b DVD] in
[Menu] may be selected. When recording
an HD (High Definition) video, select
[AVCHD dubbing] in [Menu].
®
No valid photo found in the camera.
• The camera or memory card does not
contain any photos.
Insert DVD created by this unit.
• A disc created by another device has been
inserted. A disc created by another video
device will not play back.
The disc is full.
• Even if the disc is not full, you cannot
record to the disc when the number of video
titles or photos reaches a maximum number
for recording.
Cannot record to this disc in the
selected operation.
• In some cases, full-capacity recording may
not be possible, depending on how the disc
is used.
• Usable discs differ depending on recording
stored on a camera connected with a USB
cable cannot be recorded to DVD+R DL
disc.)
Connected device error. Check the
camcorder.
Setup camera for USB connection.
• Check that the camcorder is correctly
connected to the DVDirect with USB cable.
Check that the camera is turned on.
• If a demo video is included in the
camcorder, the camera may not operate
normally. Delete a demo video from the
camera.
• Setup for USB connection on the camera
may not be correct. Connection to the
DVDirect is similar to connecting to a
computer.
Unknown USB device found. Check
the connected device.
Memory card error. Check the
memory card.
• An unsupported USB device is connected
to the USB port of the DVDirect.
• An incompatible memory card is inserted.
For example, a memory card containing
video recorded by a video device other than
No valid video or photo found in the
camera.
®
a Handycam is incompatible.
• The camera or memory card does not
contain any videos or photos.
System error.
• When this message appears repeatedly, the
DVDirect may be damaged.
No valid video found in the camera.
• The camera or memory card has no video to
record.
73
XX/YY videos are not recordable.
Continue copying?
• HD (High Definition) video taken in REC
mode at a bit rate exceeding 18Mbps, such
as in [HD FX] mode (for example, High
Definition HandycamR) is contained in a
camera or memory card. Such video does
not comply with AVCHD format. Select
[Yes] to record other than the above
condition videos. (XX/YY: number of un-
recordable videos/total number of videos)
74
Supported Discs and Memory Cards
Discs
The following writable discs are compatible with the DVDirect. However, not all disc
operations are supported.
Disc type
Logo
Usable discs
Supported versions
DVD+R
Up to 16× media
DVD+R DL
*
Up to 8× media
Up to 8× media
Up to 8× media
Up to 16× media
(Double layer)
DVD+RW
DVD+RW
High speed
DVD-R
DVD-R DL
(Double layer)
DVD-RW
Up to 6× media
*
Only use when connecting to the DV IN or VIDEO IN connector.
z Hint
• The DVDirect supports both CPRM and non-CPRM discs.
b Note
• Blu-ray disc, DVD-R DL (Double layer), CD-R, CD-RW and 8cm discs are not supported.
Notes on using discs
• When adding videos to a previously-recorded disc (unfinalized disc), connect a camcorder
to the DVDirect using the same connector as the previous recording. For example, you
cannot add recordings to the disc using the VIDEO IN connector after recording to the disc
using the USB port.
• You cannot add recordings to a disc created on a PC or other DVD device.
75
• When copying HD (High Definition) videos, always use a new disc. You cannot add HD
(High Definition) videos to the same disc to which you have previously recorded HD (High
Definition) videos.
• The quality of commercially-made recordable discs can vary. Sub-standard discs may not
record normally.
• Some recorded discs cannot be played on playback devices due to the recording quality or
physical condition of the disc, or the characteristics of the playback device and playback
software. The disc will not play if it has not been correctly finalized.
“Memory Stick”
The DVDirect supports the following types of “Memory Stick.” However, proper operation is
not guaranteed for all “Memory Stick” products.
Read
“Memory Stick” type
Memory Stick
a
Memory Stick
1
1
a*
a
(MagicGate/High-speed data transfer compatible)
Memory Stick Duo
Memory Stick Duo
(MagicGate/High-speed data transfer compatible)
a*
1
MagicGate Memory Stick
MagicGate Memory Stick Duo
Memory Stick PRO
a*
a*
a*
1
1
1 2
Memory Stick PRO Duo
Memory Stick PRO-HG Duo
a* *
1 2 3
a* * *
*
*
1 Reading of data that requires MagicGate functions cannot be performed with the DVDirect.
2 Sony Memory Stick PRO Duo or Sony Memory Stick PRO-HG Duo operation is supported, up to
32 Gbytes. The memory card slot of the DVDirect does not support capacities exceeding 32
Gbytes. Even if you insert such a card into the camera’s memory card slot and connect the camera
to the DVDirect with the USB cable, recording will not be available (as of January 2010).
*3 8-bit parallel data transfer is not supported.
Notes on using “Memory Stick”
• If you slide the write-protect switch to LOCK with a fine-tipped object, you cannot record,
edit, or delete images.
76
Terminal
Write enable
position
Write protect
position
LOCK
LOCK
Memo area
• Insert a “Memory Stick” into the Multi memory card slot, and insert a “Memory Stick Duo”
into the “Memory Stick Duo” slot. When inserting a “Memory Stick Duo” with an adapter
into the Multi memory card slot, the DVDirect may not work properly.
• Not all memory card operations are supported with card adapters.
• Slide the write protect switch with a thin implement.
• Use your camera to format the “Memory Stick.” A “Memory Stick” formatted on a
computer may not work properly.
• The position and shape of the write-protect switch may differ depending on the “Memory
Stick” you use.
• Do not remove the “Memory Stick” while recording or when the Memory card access LED
is on.
• Data may be corrupted if:
- the “Memory Stick” is removed or the DVDirect is turned off while reading data, or
- the “Memory Stick” is used in locations subject to static electricity or electrical noise.
SD Card/xD-Picture Card
The DVDirect has slots for the following memory cards. However, not all memory card
operations are supported.
1
• SD Memory Card*
2
• SDHC Memory Card*
• xD-Picture Card
*1 SD Memory Card operation is supported up to 2 Gbytes.
*
2 SDHC Memory Card operation is supported up to 32 Gbytes. The memory card slot of the DVDirect
does not support capacities exceeding 32 Gbytes. Even if you insert such a card into the camera’s
memory card slot and connect the camera to the DVDirect with the USB cable, recording will not be
available (as of January 2010).
Notes on using memory cards
• Do not use a commercial card adapter. The DVDirect may not work properly.
• Do not use a metallic card adapter as malfunction may result.
• The DVDirect does not read copyright protected data.
77
Recording Time and Video Lengths
Time required for recording
When recording video, the length of time required for recording depends on the REC mode
setting (FH, HQ, SP, or LP) used to shoot the video and the number of scenes the video
contains. Typically, more time is required to record videos onto a disc if the video was
recorded with a higher image quality (bit rate) setting. The chart below provides a general
estimate of time required to record.
Recording HD (High Definition) video
(Time required to copy a 1-hour video)
Camcorder connected via “Memory Stick Duo”
Mode
a USB cable
slot on DVDirect
approx. 80 minutes*
approx. 50 minutes*
approx. 35 minutes
approx. 30 minutes
FH
HQ
SP
LP
approx. 40 minutes*
approx. 25 minutes*
approx. 20 minutes
approx. 15 minutes
*
Two discs are required.
Recording SD (Standard Definition) video
(Time required to copy a 1-hour video)
Camcorder connected via
a USB cable (Media other
than 8cm disc)
“Memory Stick Duo”
slot on DVDirect
Mode
HQ
SP
LP
approx. 35 minutes
approx. 25 minutes
approx. 15 minutes
approx. 35 minutes
approx. 25 minutes
approx. 15 minutes
z Hint
• When a camcorder is connected to the DV IN or VIDEO IN connector on the DVDirect, the length of time
required for recording is the same as the playback time of the video.
b Note
• You cannot record HD (High Definition) video taken in REC mode at a bit rate exceeding 18Mbps, such
as in [HD FX] mode (for example, High Definition Handycam®) in AVCHD format.
78
Disc space (recordable time) available for recording videos
The chart below provides a general estimate of disc space (recordable time) available for
recording videos onto a disc.
HD (High Definition) discs (AVCHD format)
The recordable video length depends on the REC mode setting on the camera.
REC mode setting used to shoot the video
DVD-R/-RW/+R/+RW
approx. 30 minutes
FH
HQ
SP
LP
approx. 55 minutes
approx. 1 hour 10 minutes
approx. 1 hour 35 minutes
SD (Standard Definition) discs (USB connection or “Memory Stick Duo” slot)
The recordable video length depends on the REC mode setting on the camera.
REC mode setting used to shoot the video
DVD-R/-RW/+R/+RW
approx. 1 hour
HQ
SP
LP
approx. 1 hour 30 minutes
approx. 3 hours
SD (Standard Definition) discs (DV IN or VIDEO IN connector)
The recordable video length depends on the [Rec Quality] (REC mode) setting on the
REC mode (Rec Quality) setting on the DVDirect DVD-R/-RW/+R/+RW
HQ
approx. 1 hour
HSP
SP
approx. 1 hour 30 minutes
approx. 2 hours
LP
approx. 3 hours
SLP
approx. 6 hours
z Hint
• When using DVD+R DL, it takes 1.8 times longer than the above time.
b Note
• You cannot record HD (High Definition) video taken in REC mode at a bit rate exceeding 18Mbps, such
as in [HD FX] mode (for example, High Definition Handycam®) in AVCHD format.
79
About Created Discs
The DVDirect creates a DVD Menu on an SD (Standard Definition) disc and a slideshow disc.
The DVD Menu is displayed each time a disc is inserted into a player and can be used to select
videos from dates or thumbnails.
According to the type of disc being created and the device connection used for recording, disc
configuration varies, and there may be some restrictions. See the following.
About SD (Standard Definition) discs
Configuration of SD (Standard Definition) discs
(DV IN or VIDEO IN connector)
DVD Menu
Disc
Title
Chapter
Start recording
End recording
The DVD Menu displays thumbnails of the titles created between the points where you start
and stop recording on the DVDirect.
For each title, chapters are automatically created according to the [Auto Chapter] setting
Configuration of SD (Standard Definition) discs
(USB port or “Memory Stick Duo” slot)
DVD Menu
Disc
Title
Scene
Chapter
• The DVD Menu displays thumbnails of the titles created at points in the video where the
shooting date changes.
80
For each title, chapters (breakpoints of a video on the disc) are automatically created by
scene between the point where you start and stop shooting on the camera.
• If you copy videos recorded in a variety of REC modes (HQ, SP, etc. setting on the camera),
different aspect ratios (16:9 or 4:3 setting on the camera), or add videos to the disc, titles
(even of the same shooting date) may be separated.
About HD (High Definition) discs
Notes on HD (High Definition) disc compatibility
• An HD (High Definition) disc cannot be played on an AVCHD incompatible DVD player
or recorder.
• Do not insert an HD (High Definition) disc in an AVCHD incompatible DVD player or
recorder. The DVD player or recorder may fail to eject the disc and may erase its contents.
• An HD (High Definition) disc can be played on an AVCHD compatible Blu-ray Disc
®
player/recorder, Playstation 3 or other compatible device.
Type of created disc and compatible devices
HD (High Definition) disc (containing High Definition videos)
Yes
No
Yes
DVD device
AVCHD format
compatible device
Computer*
SD (Standard Definition) disc (containing Standard Definition videos)
Yes
Yes
Yes
DVD device
AVCHD format
compatible device
Computer
*
Install the AVCHD compatible application on your computer beforehand. Even in the case of a
computer environment that satisfies system requirements, there may be noise in video playback,
frames may be dropped, or sound may be lost intermittently. (This does not depend on the
quality of the created disc.)
81
Configuration of HD (High Definition) discs
• The DVD Menu cannot be created.
• Chapters (breakpoints of a video on the disc) are automatically created by scene between
the point where you start and stop shooting on the camera.
• An HD (High Definition) video disc cannot be previewed on the DVDirect’s display
window.
About Photo discs
About created photo DVDs
• Photos are copied to the disc as JPEG files. File names are assigned to photos (JPEG files)
in the order they are copied to the disc.
slideshow in addition to storing photos.
• You can view the photo disc created with the DVDirect in the display window or view it
using the DVD drive of a computer. And you can also view photos using a DVD player
capable of playing JPEG files. A slideshow disc can be played on commercial DVD players.
z Hint
• The picture quality of the photos played back in a slideshow is equivalent to that of SD (Standard
Definition) video. Using the DVD drive of a computer or DVD player capable of playing JPEG files, you
can view photos in higher quality.
b Notes
• Up to 2000 photos can be copied to a disc.
• You cannot copy both videos and photos together onto the same disc.
Configuration of Slideshow discs
Disc
Title
Chapter 1
10 photos
Chapter 2
Chapter 99
• Slideshow discs consist of titles and chapters as SD (Standard Definition) discs.
• A chapter is created for every 10 photos.
• Up to 99 chapters per title can be created.
82
Additional Information
Precautions
• Do not affix labels on discs.
Operation and storage conditions
Avoid using or storing the DVDirect in hot
or humid locations, or places where it might
be subject to severe vibration or direct
sunlight.
Cleaning
Use a soft, dry cloth to clean the external
surfaces of the DVDirect. Do not use an
abrasive, disposable cloth such as paper
towels, as they may damage the surface
finish.
• Do not store discs in dusty or humid
locations, in direct sunlight, or near heat
generating devices.
• To protect important data, always keep
discs in their cases.
• Clean the disc with a cleaning cloth.
Wipe the disc from the center out.
• Data may not be recorded properly if
there are scratches or dust on the
unrecorded area of writable discs. Handle
discs very carefully.
Transportation
Please repack the DVDirect in its original
carton when shipping, and remove any disc
beforehand.
Moisture condensation
Handling memory cards
• Do not drop, bend, or submit the memory
cards to external shock.
• Do not disassemble or modify the
memory cards.
• Avoid touching the terminal of a memory
card or touching it with a metal object.
• Avoid getting liquids on a memory card
or using them in areas subject to high
humidity.
Do not expose the DVDirect to sudden
temperature changes. Do not use the
DVDirect immediately after moving it from
a cold to warm location or raising the room
temperature suddenly, as condensation may
have formed within the DVDirect. If the
temperature changes suddenly while using
the DVDirect, keep the power on, but stop
using it for at least an hour.
• Avoid using or storing a memory card in
a location subject to:
- extremely high temperature, such as
the interior of a car, outdoors exposed
to direct sunlight, or near a heater.
- direct sunlight
Handling discs
• Handle discs only by the edges. Never
touch the recording surface.
- high humidity
- corrosive substances
- excessive dust
- electrostatic or electronic noises
- magnetic fields
• When storing or carrying a memory card,
keep it in its original case to ensure
protection of important data.
• Avoid removing a memory card from its
slot or turning off the power button while
84
the DVDirect is accessing it, as data may
be rendered unreadable.
85
Specifications
Supported photo format*
JPEG, DCF2.0 compliant
Recording/Copying
Creatable discs
• Standard Definition (SD) disc
• High Definition (HD) disc (AVCHD
format)
*
The following JPEG file is supported.
Number of pixels: up to 8192×8192
File size: up to 7.2 MB
File number: up to 2000 photos
• Photo disc (JPEG files, Data DVD)
• Slideshow disc (JPEG files, DVD-
VIDEO format)
Playback
Playable discs
Discs created with VRD-MC6*
(Other commercial or recorded discs are not
supported.)
1
Recordable discs*
DVD+R, DVD+RW, DVD-R, DVD-RW,
2
DVD+R DL*
*
1 Use 12cm disc only
*
HD (High Definition) discs cannot be played
back.
*2 Use the DV IN or VIDEO IN connector only.
Output
Supported input devices (Video
recording)
DVDirect’s built-in LCD display
• Sony digital video camera
- HDD
- Built-in memory
- Memory card
- 8cm disc
- DV/D8 tape
• Sony digital still camera
- Built-in memory
- Memory card
Input/Output Interface
1
DV IN*
4-pin i.LINK (IEEE1394), S100, DVC-SD
input
VIDEO IN
1 Vp-p/75 ohms
• Video device with audio/video outputs
AUDIO IN
Supported input devices (Photo
recording)
2 Vrms (Impedance more than 47 kilohms)
2
• Sony digital video camera
- HDD
- Built-in memory
USB port*
Type A
- Memory card
- 8cm disc
• Sony digital still camera
- Built-in memory
*1 For DV input from DV digital video camera
only.
*2 For Sony camera connection only.
- Memory card
• Digital video camera other than Sony
- Memory card
• Digital still camera other than Sony
- Memory card
86
Memory Card Slot
“Memory Stick Duo”
“Memory Stick”*
SD Memory Card*
xD-Picture Card*
*
Multi card slot
General
Power
DC 12V (supplied from the DC IN jack)
Consumption
30W
AC adapter*
Type: AC-NB12A
Input: AC 100 V - 240 V
Output: DC 12 V/2.5A
*
Use an AC power cord appropriate for the
region or country of use.
Size*
Approx. 144 × 52 × 156 mm (W×H×D)
*
Including maximal projections.
Weight
Approx. 660 g
Operating temperature
5 ºC to 35 ºC
Design and specifications are subject to
change without notice.
87
P/N 7925000045B
Sony Corporation Printed in China
|