Nokia 6260 User Manual

User’s Guide for Nokia 6260

9231815

Issue 2

Bluetooth is a registered trademark of Bluetooth SIG, Inc.

Nokia operates a policy of continuous development. Nokia reserves the right to make changes and

improvements to any of the products described in this document without prior notice.

Under no circumstances shall Nokia be responsible for any loss of data or income or any special,

incidental, consequential or indirect damages howsoever caused.

The contents of this document are provided ‘as is’. Except as required by applicable law, no warranties of

any kind, either express or implied, including, but not limited to, the implied warranties of

merchantability and fitness for a particular purpose, are made in relation to the accuracy, reliability or

contents of this document. Nokia reserves the right to revise this document or withdraw it at any time

without prior notice.

The availability of particular products may vary by region. Check with the Nokia dealer nearest to you.

9231815 / Issue 2

Contents

For your safety .................................................................................................. 13

General information.......................................................................................... 17

Stickers in the sales package ................................................................................................................ 17

Access codes .............................................................................................................................................. 17

PIN code................................................................................................................................................... 17

PIN2 code................................................................................................................................................ 17

Lock code................................................................................................................................................. 18

PUK and PUK2 codes............................................................................................................................ 18

1. Getting started .............................................................................................. 19

Inserting a SIM card and a MultiMediaCard.................................................................................... 19

Charging the battery ............................................................................................................................... 21

Switching the phone on and off .......................................................................................................... 21

2. Your phone..................................................................................................... 23

Mechanical modes ................................................................................................................................... 23

Closed mode ........................................................................................................................................... 23

Work mode.............................................................................................................................................. 24

Imaging mode ........................................................................................................................................ 24

Browse mode.......................................................................................................................................... 25

Keyguard.................................................................................................................................................. 25

Keys and connectors................................................................................................................................ 26

Indicators in standby mode................................................................................................................... 28

Menu............................................................................................................................................................ 29

Actions common to all applications ................................................................................................... 30

Volume control.......................................................................................................................................... 32

3. Call functions ................................................................................................ 34

Making a call ............................................................................................................................................. 34

Using the Contacts directory............................................................................................................. 34

Calling your voice mailbox................................................................................................................. 35

Speed dialling......................................................................................................................................... 35

Making a conference call ................................................................................................................... 35

Answering a call ....................................................................................................................................... 36

Options during a call............................................................................................................................ 37

Call waiting............................................................................................................................................. 38

Diverting calls ........................................................................................................................................ 38

Push to talk ................................................................................................................................................ 39

Settings for push to talk..................................................................................................................... 40

Connecting to the push to talk service........................................................................................... 40

Making a push to talk call.................................................................................................................. 41

Receiving a push to talk call .......................................................................................................... 42

Callback requests .................................................................................................................................. 43

Sending a callback request ............................................................................................................. 43

Saving the callback request sender.............................................................................................. 44

Using groups........................................................................................................................................... 44

Adding a group................................................................................................................................... 44

Joining an existing group................................................................................................................ 45

Receiving an invitation.................................................................................................................... 45

Call register and general log................................................................................................................. 46

Recent calls register............................................................................................................................. 46

Call duration........................................................................................................................................... 47

Viewing the general log...................................................................................................................... 48

GPRS data counter................................................................................................................................ 49

4. Writing text ................................................................................................... 50

Using traditional text input................................................................................................................... 50

Using predictive text input .................................................................................................................... 51

Tips for writing text ................................................................................................................................. 52

Copying text to the clipboard............................................................................................................... 53

5. Personal information..................................................................................... 54

Contacts...................................................................................................................................................... 54

Managing contacts............................................................................................................................... 54

Adding a ringing tone.......................................................................................................................... 55

Voice dialling.......................................................................................................................................... 56

Adding a voice tag to a phone number....................................................................................... 56

Making a call by saying a voice tag............................................................................................. 57

Assigning speed-dialling keys ........................................................................................................... 57

Presence ...................................................................................................................................................... 58

Changing your availability information.......................................................................................... 59

Changing who can view your Presence information.................................................................. 59

Public viewers..................................................................................................................................... 61

Private viewers ................................................................................................................................... 61

Blocked viewers.................................................................................................................................. 62

Updating your Presence information .............................................................................................. 62

Presence settings .................................................................................................................................. 63

Positioning.................................................................................................................................................. 64

Calendar...................................................................................................................................................... 65

Creating calendar entries ................................................................................................................... 65

Calendar views....................................................................................................................................... 66

To-do............................................................................................................................................................ 67

Importing data from compatible Nokia phones .............................................................................. 68

6. Media ............................................................................................................. 69

Camera......................................................................................................................................................... 69

Taking a picture or recording a video clip ..................................................................................... 69

Image size and orientation................................................................................................................. 71

Camera settings..................................................................................................................................... 72

Viewing images...................................................................................................................................... 73

Zooming on a saved image............................................................................................................. 74

Shortcuts during zooming............................................................................................................... 74

RealPlayer™................................................................................................................................................ 75

Playing media files................................................................................................................................ 75

Shortcuts during play....................................................................................................................... 76

Changing the settings.......................................................................................................................... 77

Radio ............................................................................................................................................................ 77

Tuning and saving a radio channel.................................................................................................. 79

Using the radio ...................................................................................................................................... 79

Using the channel list.......................................................................................................................... 80

Gallery.......................................................................................................................................................... 81

Opening files........................................................................................................................................... 82

Other default folders............................................................................................................................ 82

Picture messages folder................................................................................................................... 82

Wallpapers folder .............................................................................................................................. 83

Presence logos folder........................................................................................................................ 83

Downloading files................................................................................................................................. 83

Uploading images to an image server............................................................................................. 84

7. Messaging ...................................................................................................... 85

Writing and sending messages............................................................................................................. 87

Settings for multimedia ...................................................................................................................... 89

Settings for e-mail................................................................................................................................ 89

Inbox - receiving messages ................................................................................................................... 90

Viewing multimedia objects .............................................................................................................. 90

Receiving smart messages.................................................................................................................. 91

Receiving service messages................................................................................................................ 92

My folders .................................................................................................................................................. 93

Mailbox........................................................................................................................................................ 93

Retrieving e-mail messages from the mailbox............................................................................. 94

Deleting e-mail messages................................................................................................................... 95

Outbox......................................................................................................................................................... 96

Viewing messages on a SIM card......................................................................................................... 97

Cell broadcast............................................................................................................................................ 97

Service command editor......................................................................................................................... 98

Messaging settings .................................................................................................................................. 98

Text messages ........................................................................................................................................ 98

Multimedia messages .......................................................................................................................... 99

E-mail messages................................................................................................................................. 101

Settings for Mailboxes.................................................................................................................. 101

Service messages................................................................................................................................ 103

Cell broadcast ..................................................................................................................................... 104

Settings for the Other folder .......................................................................................................... 104

Chat ........................................................................................................................................................... 105

Connecting to a chat server............................................................................................................ 105

Modifying your chat settings ......................................................................................................... 106

Joining and leaving a chat group.................................................................................................. 106

Searching for chat groups and users............................................................................................ 107

Chatting in a chat group ................................................................................................................. 108

Recording messages....................................................................................................................... 109

Blocking messages ......................................................................................................................... 109

Starting and viewing individual conversations......................................................................... 109

Chat contacts...................................................................................................................................... 110

Creating a new chat group ............................................................................................................. 111

Editing chat group settings ......................................................................................................... 112

Restricting access to a chat group............................................................................................ 112

Chat and Presence servers............................................................................................................... 113

8. Tools ............................................................................................................. 114

Applications ............................................................................................................................................ 114

Downloading an application........................................................................................................... 115

Installing an application.................................................................................................................. 116

Installing a Java™application...................................................................................................... 117

Launching an application ................................................................................................................ 118

Other options available for an application or application set........................................... 118

Memory status for applications..................................................................................................... 119

Removing an application................................................................................................................. 119

File manager ........................................................................................................................................... 119

Receiving files via Infrared.............................................................................................................. 120

Viewing memory consumption....................................................................................................... 120

Voice commands.................................................................................................................................... 121

Adding a voice command to an application............................................................................... 122

Starting an application using a voice command ...................................................................... 123

Replaying, erasing, or changing a voice command.................................................................. 123

Device manager...................................................................................................................................... 124

9. Personalising your phone............................................................................ 126

Profiles...................................................................................................................................................... 126

Themes...................................................................................................................................................... 127

Settings .................................................................................................................................................... 129

Changing general settings............................................................................................................... 129

Phone settings .................................................................................................................................... 130

Call settings......................................................................................................................................... 132

Connection settings .......................................................................................................................... 133

Access points ................................................................................................................................... 133

GPRS................................................................................................................................................... 137

Data call............................................................................................................................................ 138

Date and time ..................................................................................................................................... 138

Security................................................................................................................................................. 139

Phone and SIM................................................................................................................................ 139

Certificate management............................................................................................................... 140

Call barring .......................................................................................................................................... 142

Network ................................................................................................................................................ 143

Enhancement settings...................................................................................................................... 143

Go to.......................................................................................................................................................... 144

10.Extras.......................................................................................................... 146

Wallet ...................................................................................................................................................... 146

Entering the wallet code.................................................................................................................. 146

Storing personal card details.......................................................................................................... 147

Creating personal notes................................................................................................................... 148

Creating a wallet profile.................................................................................................................. 148

Retrieving information from the wallet to your browser....................................................... 149

Viewing ticket details ....................................................................................................................... 150

Wallet settings.................................................................................................................................... 150

Resetting the wallet and wallet code.......................................................................................... 151

Calculator ................................................................................................................................................ 151

Converter ................................................................................................................................................. 152

Converting units................................................................................................................................. 152

Setting a base currency and exchange rates............................................................................. 153

Notes......................................................................................................................................................... 154

Clock.......................................................................................................................................................... 154

Changing clock settings................................................................................................................... 154

Setting an alarm................................................................................................................................. 154

Personalising the alarm tone ...................................................................................................... 155

Recorder................................................................................................................................................... 155

Memory card........................................................................................................................................... 156

Formatting the memory card.......................................................................................................... 157

Backing up and restoring information......................................................................................... 157

Locking the memory card ................................................................................................................ 158

Unlocking a memory card ............................................................................................................ 158

Checking memory consumption .................................................................................................... 158

Quickword................................................................................................................................................ 159

Quickpoint ............................................................................................................................................... 159

11.Services and Applications.......................................................................... 160

Web (Mobile browser).......................................................................................................................... 160

Basic steps for accessing ................................................................................................................. 160

Setting up the phone for the browser service........................................................................... 161

Receiving settings in a smart message .................................................................................... 161

Keying in the settings manually................................................................................................. 161

Making a connection ........................................................................................................................ 161

Viewing bookmarks............................................................................................................................ 162

Adding bookmarks manually....................................................................................................... 163

Browsing............................................................................................................................................... 163

Keys and commands used in browsing..................................................................................... 163

Saving bookmarks........................................................................................................................... 164

Viewing saved pages...................................................................................................................... 164

Downloading ....................................................................................................................................... 165

Purchasing an item ........................................................................................................................ 166

Checking an item before downloading .................................................................................... 166

Ending a connection ......................................................................................................................... 167

Browser settings................................................................................................................................. 167

Games ....................................................................................................................................................... 168

12.Connectivity ............................................................................................... 169

Bluetooth connection........................................................................................................................... 169

Bluetooth connection settings....................................................................................................... 170

Sending data via Bluetooth technology...................................................................................... 170

Paired devices view ........................................................................................................................... 172

Receiving data via Bluetooth wireless technology................................................................... 173

Disconnecting Bluetooth connection........................................................................................... 174

Infrared connection .............................................................................................................................. 174

VPN............................................................................................................................................................ 175

Connection manager ............................................................................................................................ 176

Viewing connection details............................................................................................................. 177

Ending connections........................................................................................................................... 177

Connecting your phone to a compatible computer..................................................................... 178

Using your phone as a modem .......................................................................................................... 178

Remote synchronisation...................................................................................................................... 178

Creating a new synchronisation profile....................................................................................... 179

Synchronising data............................................................................................................................ 180

13.Troubleshooting ......................................................................................... 181

Q&A........................................................................................................................................................... 182

14.Battery information................................................................................... 187

Care and Maintenance.................................................................................... 190

Additional safety information........................................................................ 192

For your safety

Read these simple guidelines. Not following them may be dangerous or illegal. Read the

complete user guide for further information.

SWITCH ON SAFELY

Do not switch the phone on when wireless phone use is prohibited or when it

may cause interference or danger.

ROAD SAFETY COMES FIRST

Obey all local laws. Always keep your hands free to operate the vehicle while

driving. Your first consideration while driving should be road safety.

INTERFERENCE

All wireless phones may be susceptible to interference, which could affect

performance.

SWITCH OFF IN HOSPITALS

Follow any restrictions. Switch the phone off near medical equipment.

SWITCH OFF IN AIRCRAFT

Follow any restrictions. Wireless devices can cause interference in aircraft.

SWITCH OFF WHEN REFUELLING

Do not use the phone at a refuelling point. Do not use near fuel or chemicals.

SWITCH OFF NEAR BLASTING

Follow any restrictions. Do not use the phone where blasting is in progress.

USE SENSIBLY

Use only in the normal position as explained in the product documentation. Do

not touch the antenna unnecessarily.

QUALIFIED SERVICE

Only qualified personnel may install or repair this product.

ENHANCEMENTS AND BATTERIES

Use only approved enhancements and batteries. Do not connect incompatible

products.

WATER-RESISTANCE

Your phone is not water-resistant. Keep it dry.

BACK-UP COPIES

Remember to make back-up copies or keep a written record of all important

information stored in your phone.

CONNECTING TO OTHER DEVICES

When connecting to any other device, read its user guide for detailed safety

instructions. Do not connect incompatible products.

EMERGENCY CALLS

Ensure the phone is switched on and in service. Press

as many times as

needed to clear the display and return to the start screen. Key in the emergency

number, then press

permission to do so.

. Give your location. Do not end the call until given

■ About your device

The wireless device described in this guide is approved for use on the EGSM 900, GSM 1800

and GSM 1900 networks. Contact your service provider for more information about

networks.

When using the features in this device, obey all laws and respect privacy and legitimate

rights of others.

Warning: To use any features in this device, other than the alarm clock, the device

must be switched on. Do not switch the device on when wireless device use may

cause interference or danger.

■ Network Services

To use the phone you must have service from a wireless service provider. Many of the

features in this device depend on features in the wireless network to function. These

Network Services may not be available on all networks or you may have to make specific

arrangements with your service provider before you can utilize Network Services. Your

service provider may need to give you additional instructions for their use and explain what

charges will apply. Some networks may have limitations that affect how you can use

Network Services. For instance, some networks may not support all language-dependent

characters and services.

Your service provider may have requested that certain features be disabled or not activated

in your device. If so, they will not appear on your device menu. Contact your service provider

for more information.

This device supports WAP 2.0 protocols (HTTP and SSL) that run on TCP/IP protocols. Some

features of this device require network support for these technologies.

■ Shared memory

The following features in this device may share memory: contacts, text messages, and

multimedia messages, images and ringing tones, video recorder, RealOne Player^TM, calendar

and to-do notes, and downloaded applications. Use of one or more of these features may

reduce the memory available for the remaining features sharing memory. For example,

saving many images may use all of the available memory. Your device may display a message

that the memory is full when you try to use a shared memory feature. In this case, delete

some of the information or entries stored in the shared memory features before continuing.

Some of the features may have a certain amount of memory specially allotted to them in

addition to the memory shared with other features.

General information

■ Stickers in the sales package

The stickers included on the warranty card,in the sales package, contain important

information for service and customer support purposes. The sales package also

includes instructions on how to use the stickers.

■ Access codes

PIN code

The PIN (Personal Identification Number, 4 to 8 digits) code helps to protect your

SIM card against unauthorised use. The PIN code is usually supplied with the SIM

card.

After three consecutive incorrect PIN code entries, the PIN code is blocked. If the

PIN code is blocked, you need to unblock it with the PUK code before you can use

the SIM card again.

PIN2 code

The PIN2 code (4 to 8 digits), supplied with some SIM cards, is required to access

some functions.

Lock code

The lock code (5 digits) can be used to lock the phone and keypad to avoid

unauthorised use.

The factory setting for the lock code is 12345. To avoid unauthorised use of your

phone, change the lock code. Keep the new code secret and in a safe place

separate from your phone.

PUK and PUK2 codes

The PUK (Personal Unblocking Key, 8 digits) code is required to change a blocked

PIN code. The PUK2 code is required to change a blocked PIN2 code. If the codes

are not supplied with the SIM card, contact the operator whose SIM card is in your

phone for the codes.

1. Getting started

Note: Before removing the cover, always switch off the power and disconnect the

charger and any other device. Avoid touching electronic components while

changing the covers. Always store and use the device with the covers attached.

■ Inserting a SIM card and a MultiMediaCard

1. Open the phone cover: With the back of

the phone facing you, press the locking

catch in the direction of the arrow and lift

the cover.

2. Open the memory card holder by pressing

it gently. Insert the SIM card into the bottom

slot. Make sure the bevelled corner on the SIM

card is facing towards the top of the phone and

that the golden contact area on the card is

facing downwards. To slide the SIM card out of

the slot, move the card holder towards the

battery slot.

3. Insert the Reduced Size MultiMedia Card (RS-

MMC) into the holder’s slot. Make sure that

the bevelled corner and golden contact area of

the RS-MMC are facing downwards.

4. Close the memory card holder by pressing it

downwards until locked.

5. Align the golden contacts of the battery

with the corresponding connectors on the

phone, and push the opposite end of the

battery until it snaps into place.

6. Close the phone cover.

Keep all SIM cards out of the reach of small children. For availability and information on

using SIM card services, contact your SIM card vendor. This may be the service provider,

network operator, or other vendor.

Use only compatible Multimedia cards (MMC) with this device. The compatible MMC for

your device is Reduced Size Dual Voltage MultiMediaCard. Other memory cards, such as

Secure Digital (SD) cards, do not fit in the MMC card slot and are not compatible with this

device. Using an incompatible memory card may damage the memory card as well as the

device, and data stored on the incompatible card may be corrupted.

■ Charging the battery

1. Connect the power cord to the charger.

2. Connect the other end of the power cord from the

charger to the base of the phone.

3. Connect the charger to an AC wall outlet. The battery

indicator bar on the display starts scrolling if the fold is open, and the LED light

indicator on the fold is lit if the fold is closed. Note that you can use the phone

while charging. When the battery is fully charged, the bar stops scrolling.

Disconnect the charger from the AC outlet and then from the phone. See

“Battery information” on page 187.

■ Switching the phone on and off

Press and hold

WARNING! Do not switch the phone on when wireless phone use is prohibited or

when it may cause interference or danger.

Your device has an internal antenna.

Note: As with any other radio-transmitting

device, do not touch the antenna

unnecessarily when the phone is switched on.

Contact with the antenna affects call quality

and may cause the phone to operate at a

higher power level than otherwise needed.

Avoiding contact with the antenna area when

operating the phone optimises the antenna performance and the battery life.

NORMAL POSITION: Hold the phone as shown in the picture above.

If the phone requests a PIN code:

The PIN code is usually supplied with the SIM card.

•

Key in the code (displayed as ****) and press

If the phone requests a lock code:

Key in the lock code (displayed as *****) and press

•

The factory setting for the lock code is 12345.

2. Your phone

■ Mechanical modes

Your phone has four different mechanical modes: Closed, Work, Browse, and

Imaging. You switch between the modes by turning the fold and the swivel. Note

that there is a short time-out before a mode is activated.

Closed mode

When the phone is in the Closed mode, all applications are sent to

the background, the screen is shut off, and ongoing calls are

ended.

Incoming calls are indicated in Closed mode by an LED

incorporated into the cover and by a ringing tone.

Note: When the phone is in the Closed mode, the keyguard will

automatically be activated for

Camera/PTT key, but not for Volume keys.

Work mode

When you open the phone, Work mode is activated

automatically, the display is lit up and the keyboard is available.

Work mode is activated even if the fold is not fully opened.

The fold opens up to approximately 150 degrees, see the picture.

Do not try to force the fold to open more.

To answer a call when the fold is closed, open the fold.

To answer a call when you have set Ans. by opening fold to No,

open the fold and press

132.

. Refer to Call settings on page

When you are not using the camera, you can use

talk.

for push to

Imaging mode

Imaging mode is activated when you turn the fold

from Work mode so that the screen is facing either

the right or the left side of the phone. If you turn the

fold to the left, you are facing both the screen and

the camera lens so that you can take pictures of

yourself.

In Imaging mode the keyboard is disabled except for

the

key

key to access the menu and the selection

on the centre of the scroll key.

Browse mode

Browse mode is activated when you open the fold up to 90

degrees, turn the fold counterclockwise (right) 180 degrees, and

close the fold. After this Browse mode is active even if you open

the fold.

When you are not using the camera, you can use

talk.

for push to

Keyguard

To activate the keyguard, press

and then

, or press

When the keyguard is on, calls still may be possible to the official emergency number

programmed into your device. Key in the emergency number and press

■ Keys and connectors

Fold open view

1. Power key

Switches the phone on and off.

When the keypad is locked, pressing the power

key turns the phone’s display lights on for

approximately 15 seconds.

2. Earpiece

3. Selection keys

and

The functions of the keys depend on the guiding

text shown on the display above the keys. Press

to display the main Menu.

4. Scroll key

Enables scrolling through names, phone

numbers, menus or settings. The scroll key is also

used to move the cursor up and down, right and

left when writing text, using the calendar, and in

some game applications. Pressing the scroll key

briefly selects the function.

opens a list of commands for text editing and marking items.

clears an entry or deletes an item and exits from different functions.

dials a phone number and answers a call. In standby mode it shows the

list of most recently called numbers.

ends an active call. Exits from any function.

–

enter numbers and characters.

and

are used for various purposes in different functions.

Fold closed view

1. Volume/Zoom keys

Adjust the volume of the earpiece or the

loudspeaker, or the headset when it is

connected to the phone. These keys also zoom

in and out when you are using the built-in

camera.

2. Loudspeakers

3. Camera/PTT key

In imaging mode, takes a picture.

In work and browse mode, pressing and

holding the key makes a push to talk call.

4. LED to indicate an incoming call.

Connectors view

1. Charger connector

2. Pop-Port^TMconnector used, for

example, for headsets and the data

cable.

3. Infrared (IR) port

4. Camera lens

■ Indicators in standby mode

You have received one or several messages to the Inbox in Messaging.

You have received one or several voice messages. See “Calling your voice

mailbox” on page 35.

There are messages waiting to be sent in the Outbox.

Ringing tone has been set to Silent, Message alert tone to None, and Chat

alert tone to None in the currently active profile.

The phone’s keypad is locked. See “Keyguard” on page 25.

You have an active alarm.

You can make calls using phone line 2 only (Network Service). See “Call

settings” on page 132.

All calls to the phone are diverted.

- Indicates that all calls to the

phone are diverted to a voice mailbox. See “Diverting calls” on page 38. If

you have two phone lines, the divert indicator for the first line is

and for the second line

A data call is active.

A fax call is active.

Shown instead of the antenna symbol (shown in the top left corner in

standby mode) when there is an active GPRS connection. - Shown

when the GPRS connection is put on hold during voice calls.

Bluetooth connection is active. When data are transmitted via Bluetooth

wireless technology ,

is shown.

An infrared connection is active.

■ Menu

Press

applications in your phone.

Options in the Menu: Open, List view/Grid view, Move, Move to folder, New

to display the main Menu. In the Menu you can access all the

folder, App. downloads, Memory details, Help and Exit.

Moving in the Menu

Press the scroll key on the top

and right to navigate the Menu.

•

, bottom

, left

Opening applications or folders

Scroll to an application or a folder and press the

centre of the scroll key to open it.

•

Closing applications

•

Press Back or Exit as many times as needed to return to standby mode or select

Options→ Exit.

Switching between applications

Press and hold to switch from one open application to another. The

application switching window opens showing a list of applications that are

currently open. Scroll to an application and press to go to it.

•

■ Actions common to all applications

•

Opening items for viewing - Scroll to an item and press

Options→Open.

Editing items - Open the item for viewing and select Options→Edit. Use the

scroll key to scroll through all fields of the item.

, or select

Removing, deleting items - Scroll to the item and select Options→Delete or

press

. To delete many items at a time, you first need to mark them.

•

Marking an item - There are several ways to select items when you are in a list.

•

To select one item at a time, scroll to the item and select Options→ Mark/

Unmark→Mark or press

and

at the same time. A check mark is

placed next to the item.

•

To select all items in the list, select Options→Mark/Unmark→ Mark all.

To mark multiple items, press and hold and then move the scroll key

down or up. As the selection moves, a check mark is placed next to the

items. To end the selection, stop the scrolling with the scroll key and then

release

After you have selected all the items that you want, you can move or delete

them by selecting Options→ Move to folder or Delete.

•

Unmarking an item - Scroll to the item and select Options→Mark/

Unmark→Unmark or press and at the same time.

Creating folders - Select Options→ New folder. You are asked to give a name

to the folder (max. 35 letters).

Moving items to a folder - Select Options→Move to folder (not shown if

there are no folders available). When you select Move to folder, a list of

available folders opens and you can also see the root level of the application

(for moving an item out of a folder). Select the location that you want the item

to be moved to and press OK.

•

Sending items - Scroll to the item and select Options→Send. Select the

method, the choices are Via multimedia, Via bluetooth, Via e-mail, Via fax and

Via infrared.

•

If you choose to send the item in an e-mail or a multimedia message, an

editor opens. Press to select the recipient(s) from the Contacts

directory or write the phone number or e-mail address of the recipient in

the To: field. Add text or sound and select Options→Send. See “Writing and

sending messages” on page 87.

Via Bluetooth. See “Sending data via Bluetooth technology” on page 170.

being copied, modified, transferred or forwarded.

■ Volume control

Voice volume icons:

- for earpiece mode,

- for loudspeaker mode.

When you have an active call or are listening to a sound, press

or the

volume control side keys to increase or decrease the volume level, respectively.

The loudspeaker allows you to speak and listen to the phone from a short distance

without having to hold the phone to your ear, for example, having it on a table

nearby. The loudspeaker can be used during a call, with sound and video

applications, and when viewing multimedia messages. Sound and video

applications use the loudspeaker by default. Using the loudspeaker makes it easier

to use other applications during a call.

To start using the loudspeaker during an already active call,

select Options→Activate loudsp.. A tone is played,

is shown

in the navigation bar, and the volume indicator changes.

The loudspeaker cannot be activated during a call when you have connected a

headset to the phone.

WARNING! Do not hold the device near your ear when the loudspeaker is

in use, because the volume may be extremely loud.

To turn off the loudspeaker when you have an active call, select

Options→Activate handset.

3. Call functions

■ Making a call

1. In standby mode, key in the phone number, including the area code. Press

to move the cursor. Press

to remove a number.

•

For international calls, press

twice for the international prefix (+)

and then key in the country code, the area code without 0, and the phone

number.

2. Press

3. Press

Pressing

to call the number.

or close the fold to end the call (or to cancel the call attempt).

ends a call even if another application is active and displayed.

You can make a call using your voice so that you do not need to look at the display

to key in the number. See “Voice dialling” on page 56.

Using the Contacts directory

Go to Menu→Contacts.

1. To find a contact, scroll to the desired name, or key in the first letters of the

name. The Search field opens automatically, and matching contacts are listed.

2. Press

to start the call.

If the contact has more than one phone number, scroll to the number and press

to start the call.

Calling your voice mailbox

The voice mailbox (network service) is an answering service where callers who are

unable to reach you can leave you voice messages.

•

To call your voice mailbox, press

and

in standby mode.

If the phone asks for the voice mailbox number, key it in and press OK. You can

obtain this number from your service provider.

•

To change the phone number of your voice mailbox, go to

Menu→Tools→Voice mailbox and select Options→Change number. Key in

the number (obtained from your service provider) and press OK.

See “Diverting calls” on page 38.

Speed dialling

Go to Menu→Tools→Speed dial.

1. Assign a phone number to one of the speed-dialling keys

(

). See “Assigning speed-dialling keys” on page 57.

2. To call the number: In standby mode, press the corresponding speed-dialling

key and . If the Speed dialling function is set to On: press and hold the

corresponding speed-dialling key until the call is started.

Making a conference call

You can make conference calls with up to six participants (network service).

1. Make a call to the first participant.

2. To make a call to a new participant, select Options→New call. Key in or search

the memory for the phone number of the participant and press OK. The first

call is automatically put on hold.

3. When the new call has been answered, join the first participant in the

conference call. Select Options→ Conference.

4. To add a new person to the call, repeat step 2 and then select Options→

Conference→ Add to conference.

•

To have a private conversation with one of the participants, select

Options→ Conference→ Private. Scroll to the desired participant and press

Private. The conference call is put on hold in your phone, and the other

participants can still continue talking with each other. Press Cancel to

return to the conference call.

•

To drop one participant from the conference call, select

Options→Conference→Dropparticipant, then scroll to the participant and

press Drop.

5. To end the active conference call, press

■ Answering a call

•

To answer an incoming call, press

•

To end the call, press

If you do not want to answer a call, press

. The caller hears a ’line busy’ tone.

When a call comes in, press Silence to quickly mute the ringing tone.

Options during a call

Many of the options that you can use during a call are network services. For

availability, contact your network operator or service provider.

Press Options during a call for some of the following options:

Mute/Unmute, Activate handset, Activate loudsp., or Activate handsfree (if a

compatible Bluetooth headset is attached), and the network services End active

call, End all calls, Hold/Unhold, New call, Conference, Private, Drop participant,

Answer, Reject and:

Swap - Switch between the active call and the call on hold.

Transfer - Connect an incoming call or a call on hold with an active call and to

disconnect yourself from both calls.

Send DTMF - Send DTMF tone sequences, for example, passwords or bank account

numbers.

Sending DTMF tone sequences

1. Key in the digits with

. Each keystroke generates a DTMF tone,

repeatedly to

which is transmitted while the call is active. Press

produce: *, p (inserts a pause of approximately 2 seconds before or between

DTMF characters.), and w (if you use this character, the remaining sequence is

not sent until you press Send again during the call). Press

to produce

2. To send the tone, press OK.

Call waiting

If you have activated the Call waiting service (network service), you will be

notified of a new incoming call while you have a call in progress.

1. During a call, press

to answer the waiting call. The first call is put on

hold. To switch between the two calls, press Swap.

2. To end the active call, press

Diverting calls

Go to Menu→Settings→Call divert.

When this network service is activated, you can direct your incoming calls to

another number, for example, to your voice mailbox number. For details, contact

your service provider.

•

Select one of the divert options, for example, select If busy to divert voice calls

when your number is busy or when you reject incoming calls.

Select Options→ Activate to set the divert setting on, Cancel to set the divert

setting off, or Check status to check whether the divert is activated or not.

To cancel all active diverts, select Options→ Cancel all diverts.

See “Indicators in standby mode” on page 28.

You cannot have barring of incoming calls and call diverting active at the same

time. See “Call barring” on page 142.

■ Push to talk

Go to Menu→Push to talk.

Push to talk over cellular is a two-way radio service (network service) available

over a GSM/GPRS cellular network. Push to talk provides direct voice

communication connected with pressing

You can use push to talk to have a conversation with one person or with a group

of people having compatible devices. When your call is connected, the person or

group you are calling does not have to answer the phone. Besides the GPRS

counters, the phone registers only one-to-one calls in the recent calls lists in Log.

The participants should confirm the reception of any communications where

appropriate as there is no other confirmation of whether the recipient(s)

has(have) heard the call.

To check availability and costs, and to subscribe to the service, contact your

network operator or service provider. Note that roaming services may be more

limited than for normal calls.

Before you can use the push to talk service, you must define the required push to

talk service settings.

While connected to the push to talk service, you can use the other functions of the

phone. The push to talk service is not connected to traditional voice

communication, and therefore many of the services available for traditional voice

calls (for example, voice mailbox) are not available for push to talk

communications.

Settings for push to talk

Go to Options→Settings.

For push to talk service settings, contact your network operator or service

provider. You may receive the settings over the air.

•

Notification tone - A tone for incoming push to talk calls.

Default nickname - Your nickname shown to other users.

Domain - The default domain name.

Access point name - The access point name for the push to talk service.

Server address - The push to talk server address.

Show my PTT address - Select No if you want to hide your push to talk address

from the receivers of your push to talk group or one-to-one calls.

•

User name - Your user name used to enter the push to talk service.

PTT password - Your password used to enter the push to talk service.

Realm - The name of the domain used for group user authentication.

After modifying the settings, restart the push to talk application.

Connecting to the push to talk service

Go to Menu→Push to talk. Alternatively, press and hold

to connect to the service.

for a few seconds

The push to talk application automatically attempts to connect to the push to talk

service. If the login is successful, the push to talk sessions view opens.

indicates the push to talk connection. If you have added group(s) to the phone,

you are automatically joined to the active groups, and the name of the default

group is displayed in standby mode.

indicates that the service is temporarily unavailable. The phone automatically

tries to reconnect to the service until you disconnect from the push to talk service.

If the login fails, you get an error note such as Unable to switch Push to talk on.

Press Options and select Switch PTT on to try to log in again, Settings to open the

settings view, or Exit to close the error note.

To disconnect from the push to talk service, select Options→Switch PTT off.

Options in the sessions view are: Deactivate loudsp./Activate loudsp.,

Active members, PTT contacts, PTT log, Settings, Help, Switch PTT off, and Exit.

Making a push to talk call

Select Options→Deactivate loudsp./Activate loudsp. to use either loudspeaker or

earpiece for push to talk communication. When the earpiece is selected, you can

use the phone normally to your ear.

Warning: Do not hold the device near your ear when the loudspeaker is in use,

because the volume may be extremely loud.

To make a push to talk call

1. Select Options→PTT contacts and search for a contact person or a group.

To open the Push to talk groups view, press

2. Press

. This starts a push to talk call immediately.

Select Options→Send callback req.. This sends a callback request to the

selected push to talk contact or group.

A tone sounds indicating that the access is granted, and the phone displays

your nickname and group name.

3. To request a speech turn, press . The phone sends your request. Wait until

your phone receives a speech turn signal. When the phone displays Talk, you

have 30 seconds to talk on your speech turn.

Press and hold

the entire time you are talking, and hold the phone in front

of you so that you can see the display. When you have finished, release the

key. Talking is allowed on a first-come, first-served basis. When someone stops

talking, the first person to press

can talk next.

4. To switch between several active sessions, select Swap.

5. To end the active session, select Deactiv..

If you have other active sessions, the phone moves to the next session.

If there are no other sessions, the phone displays a note stating that there are

no active sessions.

6. To exit the push to talk application, select Options→Exit.

Receiving a push to talk call

A short tone notifies you of an incoming group or a one-to-one call. Press Accept

to receive the call or Silence to reject it.

When receiving a group call, the group name and the nickname of the caller are

displayed. When receiving a one-to-one call from a person whose information you

have saved in Contacts, the saved name is displayed if identified; otherwise, only

the nickname of the caller is displayed.

Callback requests

Go to Options→PTT contacts or PTT log.

Sending a callback request

If you make a one-to-one call and do not get a response, you can send a request

for the person to call you back. You can send a callback request in different ways:

•

To send a callback request from the contacts list in the Push to talk menu,

select Options→PTT contacts. Scroll to a contact and press Options→Send

callback req..

To send a callback request from the Contacts, press

in standby mode, and

scroll to the desired contact. Press Details, scroll to the push to talk address

and press Options→Send callback req..

To send a callback request from the group list in the Push to talk menu, select

Options→PTT contacts and press

Options→Send callback req..

. Scroll to the desired group and press

To send a callback request from the callback request list in the Push to talk

menu, select Options→PTT log. Select Received callback reqs. and press

Options→Open. Scroll to a contact and press Options→Send callback req..

Saving the callback request sender

When you receive a callback request from someone who is not in your contacts

list, you can save the name to your contacts.

1. To open the request, select Options→PTT log→Received callback reqs..

2. Scroll to the a contact and press Options→Add to Contacts.

Using groups

Go to Options→PTT contacts.

When you call a group, all members joined to the group hear the call

simultaneously.

Each member in the groups is identified by a user name given by the service

provider. Group members can choose a nickname for within each group, which is

shown as a caller identification.

Groups are registered with a URL address. One user registers the group URL in the

network by joining the group session the first time.

Adding a group

1. Press Options→PTT contacts and then

. This opens the Push to talk groups

view.

2. Press Options→Add group→Create new.

3. Key in a Group name, and press OK.

4. Select a Group privacy level.

5. Key in your own nickname in Nickname in group.

6. To add a thumbnail image to the group, select Options→Add thumbnail.

7. Press Done. To add members and to send an invitation to the group, press Yes

when the phone requests for Send group invitation to all members now?. This

opens a view where you can select members for the group.

The members you invite to the open groups can also invite more members to

the group.

Joining an existing group

For group detail information, contact your network operator or service provider.

You may receive the details over the air.

1. Press Menu→Push to talk→PTT contacts and then

. This opens the Push

to talk groups view.

2. Press Options→Add group→Join existing.

3. Key in the Group address, Group name, and Nickname in group. You can also

add a Group thumbnail.

4. Press Done.

Receiving an invitation

When you receive a text message invitation to a group,press Options and select

an option.

•

From - View the contact information of the person who sent the invitation.

Nickname - View the nickname of the person who sent the invitation.

Group name - View the name of the group if the group is not a secured group.

•

Group address - View the group address if the group is not a secured group.

Save group - Add the group to your phone. After the group is saved, the phone

asks whether you want to connect to the saved group.

To reject the invitation, press Back and Yes.

■ Call register and general log

Go to Menu→Log.

In the log, you can monitor phone calls, text messages, packet data

connections, and fax and data calls registered by the phone. You can filter the log

to view just one type of event and create new contact cards based on the log

information.

Connections to your remote mailbox, multimedia messaging centre, or browser

pages are shown as data calls or packet data connections in the general

communications log.

Recent calls register

Go to Menu→Log→Recent calls.

The phone registers the phone numbers of missed, received, and dialled calls, and

the approximate duration of your calls. The phone registers missed and received

calls only if the network supports these functions, and the phone is switched on

and is within the network’s service area.

Options in the Missed, Received, and Dialled views: Call, Create message,

Use number, Delete, Clear list, Add to Contacts, Help, and Exit.

Missed calls and received calls

To view a list of the last 20 phone numbers from which somebody has tried to call

you without success (network service), go to Log→Recent calls→Missed calls.

To view a list of the 20 numbers or names from which you have most recently

accepted calls (network service), go to Log→Recent calls→Received calls.

Dialled numbers

To view the 20 phone numbers that you have most recently called or attempted to

call, go to Log→Recent calls→Dialled nos..

Erasing recent call lists

•

To clear all recent call lists, select Options→Clear recent calls in the Recent

calls main view.

To clear one of the call registers, open the register you want to erase and select

Options→Clear list.

To clear an individual event, open a register, scroll to the event, and press

Call duration

Go to Menu→Log→Call duration.

Allows you to view the duration of your incoming and outgoing calls.

Note: The actual time invoiced for calls by your service provider may vary,

depending on network features, rounding off for billing, and so forth.

Erasing call duration timers - Select Options→Clear timers. For this, you need

the lock code. See “Security” on page 139.

Viewing the general log

Go to Menu→Log and press

In the general log, for each communication event, you can see the sender or

recipient name, phone number, name of the service provider, or access point.

Sub-events, such as a text message sent in more than one part and packet data

connections, are logged as one communication event.

Filtering the log

1. Select Options→Filter. A list of filters opens.

2. Scroll to a filter and press Select.

Erasing the contents of the log

•

To erase all the log contents, Recent calls register, and Messaging delivery

reports permanently, select Options→Clear log. Confirm by pressing Yes.

Packet data counter and connection timer

•

To view how much data, measured in kilobytes, has been transferred and the

approximate length of a certain GPRS connection, scroll to an Incoming or

Outgoing event with the access point icon and select Options→View

details.

Log settings

Select Options→Settings. The list of settings opens.

•

Log duration - The log events remain in the phone memory for a set number

of days after which they are automatically erased to free memory.

•

If you select No log, all the log contents, Recent calls register, and

Messaging delivery reports are permanently deleted.

Show call duration. See “Call duration” on page 47.

GPRS data counter

Go to Menu→Log→GPRS counter.

The GPRS data counter allows you to check the amount of data sent and received

during packet data (GPRS) connections.

4. Writing text

You can key in text, for example, when writing messages, using traditional or

predictive text input.

■ Using traditional text input

The indicator

is shown on the top right of the display when you are writing

text using traditional text input.

•

Press a number key (

), repeatedly until the desired character

appears. Note that there are more characters available for a number key than

are printed on the key.

•

To insert a number, press and hold the number key.

To switch between letter and number mode, press and hold

If the next letter is located on the same key as the present one, wait until the

cursor appears (or press

letter.

to end the time-out period), and then key in the

. To move the cursor to the next line, press

•

To insert a space, press

three times.

To switch between upper and lower case, press

■ Using predictive text input

You can key in any letter with a single keypress using predictive text input. To

activate predictive text input, press

and select Dictionary on. This activates

predictive text input for all editors in the phone. The

the top of the display.

indicator is shown at

1. Write the desired word by pressing the keys

. Press each key

only once for one letter. The word changes after every key press.

2. When you have finished the word, check that it is correct.

•

If the word is correct, you can confirm it by pressing

to insert a space. The underlining disappears and you can begin to

write a new word.

If the word is not correct, you have the following options:

or by pressing

•

Press

repeatedly to view the matching words the dictionary has

found one by one.

•

Press

and select Dictionary→ Matches to view a list of matching

words. Scroll to the word you want to use and press

to select it.

•

If the ? character is shown after the word, the word you intended to write is

not in the dictionary. To add a word to the dictionary, press Spell, key in the

word (max. 32 letters) using traditional text input, and press OK. The word

is added to the dictionary. When the dictionary becomes full, a new word

replaces the oldest added word.

To remove the ? and clear characters one by one from the word, press

■ Tips for writing text

•

To change between the different character cases Abc, abc, and ABC, press

. Note that if you press twice quickly the predictive text input

is turned off.

To insert a number in letter mode, press and hold the desired number key, or

press

and select number mode, key in the numbers you want, and press

OK.

The most common punctuation marks are available under

repeatedly to reach the desired punctuation mark.

. Press

Press

to open a list of special characters. Use the scroll key to scroll

through the list and press Select to select a character, or press

and

select Insert symbol.

The predictive text input tries to guess which commonly used punctuation

mark (.,?!‘) is needed. The order and availability of the punctuation marks

depend on the language of the dictionary.

When a word has been entered with predictive text on, you can press

, select

Dictionary and select:

•

Matches - To view a list of words that correspond to your key presses. Scroll to

the desired word and press

Insert word - To add a word (max. 32 letters) to the dictionary by using

•

traditional text input. When the dictionary becomes full, a new word replaces

the oldest added word.

•

Edit word - To open a view where you can edit the word, available only if the

word is active (underlined).

Off - To turn off predictive text input for all editors in the phone

Writing compound words

Write the first half of a compound word and confirm it by pressing

the last part of the compound word and complete the compound word by

pressing to add a space.

•

. Write

■ Copying text to the clipboard

To copy text to the clipboard, the following are the easiest methods:

1. To select letters and words, press and hold

. At the same time, press

or . As the selection moves, text is highlighted.

To select lines of text, press and hold

. At the same time press or

2. To end the selection, release pressing the scroll key while still holding

3. To copy the text to the clipboard, while still holding , press Copy.

Or, release and then press it once to open a list of editing commands, for

example, Copy or Cut.

If you want to remove the selected text from the document, press

4. To insert the text into a document, press and hold

and press Paste.

Or, press

once and select Paste.

5. Personal information

■ Contacts

Go to Menu→Contacts.

In Contacts, you can store and manage contact information, such as names,

phone numbers, and addresses.

You can also add a personal ringing tone, voice tag, or a thumbnail image to a

contact card. You can create contact groups, which allow you to send text

messages or e-mail to many recipients at the same time.

Contact information can only be sent to or received from compatible devices.

Options in the Contacts directory: Open, Call, Create message, New

contact, Open conversation, Edit, Delete, Duplicate, Add to group, Belongs to

groups, Mark/Unmark, Copy to SIM direct., Send, Contacts info, SIM directory,

Settings, Help, and Exit.

Managing contacts

Options when editing a contact: Add thumbnail/Remove thumbnail, Add

detail, Delete detail, Edit label, Help, and Exit.

1. Press

in standby mode or go to Menu→Contacts.

2. Select Options→New contact.

3. Fill in the fields you want and press Done.

•

To edit a contact, open it and then select Options→Edit.

To delete a contact, open it and select Options→Delete.

To attach a small thumbnail image to a contact, open the contact card, select

Options→Edit and then select Options→Add thumbnail.

•

To assign default numbers and addresses to a contact, open the contact card

and select Options→Defaults. A pop-up window opens, listing the different

options.

To copy names and numbers from a SIM card to your phone, select

Options→SIM directory, scroll to the name(s) you want to copy and select

Options→Copy to Contacts.

To copy a phone, fax, or pager number from Contacts to your SIM card,

scroll to the contact card you want to copy and select Options→Copy to SIM

direct.

Adding a ringing tone

You can set a ringing tone for each contact card and group. When that contact or

group member calls you, the phone plays the chosen ringing tone (if the caller’s

telephone number is sent with the call and your phone recognises it).

1. Press

group.

to open a contact card or go to the Groups list and select a contact

2. Select Options→Ringing tone. A list of ringing tones opens.

3. Use the scroll key to select the ringing tone you wish to use for the contact or

group and press Select.

•

To remove the ringing tone, select Default tone from the list of ringing tones.

Voice dialling

Go to Menu→Contacts.

You can make a phone call by saying a voice tag that has been added to a contact

card. Any spoken word(s) can be a voice tag.

Before using voice tags, note that:

•

Voice tags are not language-dependent. They are dependent on the speaker's voice.

You must say the name exactly as you said it when you recorded it.

Voice tags are sensitive to background noise. Record voice tags and use them in a quiet

environment.

•

Very short names are not accepted. Use long names and avoid similar names for different

numbers.

Note: Using voice tags may be difficult in a noisy environment or during an

emergency, so you should not rely solely upon voice dialling in all circumstances.

Adding a voice tag to a phone number

Voice tags can only be added to phone numbers stored in the phone’s memory. See

“Managing contacts” on page 54.

1. In the Contacts main view, scroll to the contact that you want to add a voice

tag to, and press

to open the contact card.

2. Scroll to the number that you want to add the voice tag to, and select

Options→Add voice tag.

3. Press Start to record a voice tag. After the starting tone, clearly pronounce the

word(s) you want to record as a voice tag.

4. After recording, the phone plays the recorded tag and the note Playing voice

tag is displayed.

5. When the voice tag has been successfully saved, the note Voice tag saved is

displayed and a beep sounds. A symbol can be seen next to the number in

the contact card.

Making a call by saying a voice tag

1. In standby mode, press and hold

. A short tone is played and the note

Speak now is displayed.

2. To make a call by using a voice tag, hold the phone at a short distance away

from your mouth and face and pronounce the voice tag clearly.

3. The phone plays the original voice tag, displays the name and number, and

after a few seconds dials the number of the recognised voice tag.

•

If the phone plays an incorrect voice tag, or you want to retry voice dialling,

press Retry.

Voice dialling cannot be used when a data call or a GPRS connection is active.

Assigning speed-dialling keys

Speed dialling is a quick way to call frequently used numbers. You can assign

speed-dialling keys to eight phone numbers. The number 1 is reserved for the

voice mailbox.

1. Open the contact card for which you want a speed-dialling key and select

Options→Assign speed dial.

2. Scroll to a number and press Assign. When you return to the contact

information view, you can see the speed-dial icon next to the number.

•

To call the contact by speed-dialling, go to standby mode and press the speed-

dialling key and

■ Presence

Go to Menu→Presence.

Options in the Presence view: Open, My availability, Viewers,

Update presence, Login, Logout, Settings, Help, and Exit.

Use Presence (network service) to inform others about your availability, that is,

when, where and how you want to be contacted. Presence allows you to view and

create a dynamic profile of your contact details, visible to other users of the

service, to share information or control services. Presence information can include

your availability, whether you prefer people to call or send messages, where you

are and what you are doing.

Before you can use Presence, you need to find a service that you want to use and

then save the settings of that service. You may receive the settings in a special

text message, called a smart message, from the service provider that offers the

Presence service. See “Receiving smart messages” on page 91. For more

information, contact your service provider.

The Presence application allows you to change your own published information

and manage who is authorised to see your presence. To view the presence

information of others, you must use Contacts. See “Contacts” on page 54.

Changing your availability information

Go to Options→My availability and select:

•

Available - You are available for people to call or send you messages. For

example, when you have chosen this option for your general profile. See

“Profiles” on page 126.

•

Busy - You may be available for people to call or send you messages, for

example, when your phone is in meeting profile.

Not available - You are not available for people to call or send you messages,

for example, when your phone is in silent profile.

Changing who can view your Presence information

Go to Options→Viewers and select:

•

Public pres. - Displays limited information, for managing ways for people to

contact you. This is available to anyone you have not blocked.

•

My availability - Select Available, Busy, or Not available.

Viewers - Opens the Current viewers view of your Public pres.. See “Public

viewers” on page 61.

•

Update presence - Updates your presence information to the presence

server.

•

“Chat and Presence servers” on page 113.

Settings - Manage the publishing of your presence information.

•

Private pres. - Displays private information, so you can share more personal

information. This is only available to those that you have authorised to view

your private information. You can select the following options:

•

My availability - Select Available, Busy, or Not available.

Private message- Write a text message of up to 40 characters to describe

your current availability.

•

My presence logo - Add a logo to your availability information. Logo files

are stored in the Gallery. See “Gallery” on page 81.

Viewers - Opens the Private list view of your Private pres.. See “Private

viewers” on page 61.

Update presence - Updates your presence information on the presence

server.

“Chat and Presence servers” on page 113.

Settings - Manage the publishing of your presence.

•

Blocked pres. - Displays a screen containing no personal details. See “Blocked

viewers” on page 62.

Public viewers

Go to Public pres. and select Options→Viewers→Current viewers to see the

names, phone numbers, or user IDs of the viewers whom you do not allow to view

your private presence messages, but who are currently viewing your public

presence. You can scroll to a viewer, press Options, and select:

•

Add to private list - Allows the viewer to also see your private presence.

Block - Prevents the viewer from seeing your presence information.

Add to contacts - Adds the viewer to your Contacts directory.

Reload lists - Connect to the presence server to update the viewer lists. This

option is only available when you are offline.

Private viewers

Go to Private pres. and select Options→Viewers→Private list to see the names,

phone numbers, or user IDs of the viewers who you allow to view your private

presence messages. To prevent a viewer from seeing your private presence

messages, scroll to the viewer and press

. You can scroll to a viewer, press

Options, and select:

•

Add new - Adds a new viewer manually or from your Contacts directory. You

can only select a contact who has a user ID in the contact card.

Block - Prevents the viewer from seeing your presence information.

Add to contacts - Adds the viewer to your Contacts directory.

•

Remove from list - Removes the viewer from the private list. The option is

available also when there are marked items selected. If the list is empty, the

option is not available.

•

View details - Shows the user ID information of the viewer.

Reload lists - Connect to the presence server to update the viewer lists. This

option is only available when you are offline.

Blocked viewers

Go to Options→Viewers→Blocked pres. to see the viewers you prevented from

seeing your public and private presence messages. To allow a viewer to see your

presence information, scroll to a viewer and press

. You can scroll to a

viewer, press Options, and select:

•

Add to private list - Allows the viewer to also see your private presence.

Add new - Add a new viewer manually or from your Contacts directory. You

can only select a contact who has a user ID in the contact card.

•

Add to contacts - Adds the viewer to your Contacts directory.

View details - Shows the user ID information of the viewer.

Reload lists - Connect to the presence server to update the viewer lists. This

option is only available when you are offline.

Updating your Presence information

Go to Menu→Presence.

Once the connection has been established:

1. Key in your user ID and password and press

to login.

You obtain the user ID and password from your service provider.

2. Select Options→Update presence. The option is available when you are logged

into the server and have changed your presence information in either the

Private pres. or Public pres. view and not updated it.

3. To log out, select Options→Logout.

Presence settings

Go to Options→ Settings.

See “Chat and Presence servers” on page 113.

•

Show presence to - Select:

•

Private & public - Both public and private presence is published.

Private viewers - Only private viewers can see your presence information.

Public viewers - Both public and private viewers see your public presence

information.

•

No one - Your presence information is not published.

•

New viewer status - Specifies what level of presence new viewers are allowed

to see. Select Public or Private.

Sync. with Profiles - Defines which Presence attributes are changed when you

change your profile. Select:

•

Off - The presence attributes are not changed, even if you change your

profile.

On - Both My availability and Private message are changed when you

change your profile.

•

Availability only - Private message is not changed when you change your

profile.

Private msg. only - My availability is not changed when you change your

profile.

■ Positioning

Go to Menu→Positioning.

Positioning (network service) allows the network to detect the

approximate position of your phone. By enabling or disabling positioning, you

choose when your position information is provided to the network.

To enable positioning in your phone, select Settings→Positioning→On.

When you receive a Position request, a message is displayed showing the service

that is making the request. Press Accept to allow your position information to be

sent, or press Reject to deny the request.

Position request messages are logged in the Recv. requests list.

To view them, select Menu→Positioning→Recv. requests. The icon beside each

request indicates whether the request is new, rejected, or accepted. To see details

of a request, scroll to the request and press

. To clear the Recv. requests list,

select Options→Clear list.

■ Calendar

Go to Menu→Calendar.

In the Calendar, you can keep track of your appointments, meetings, birthdays,

anniversaries, and other events. You can also set a calendar alarm to remind you

of upcoming events. The Calendar function uses shared memory. See “Shared

memory” on page 16.

Creating calendar entries

1. Go to Options→New entry and select:

•

Meeting - Reminds you of an appointment that has a specific date and

time.

•

Memo - Write a general entry for a day.

Anniversary - Reminds you of birthdays or special dates. Anniversary entries

are repeated every year.

2. Fill in the fields. Use the scroll key to move between fields.

•

Subject/Occasion - Write a description of the event.

Location - The place of a meeting, optional.

Start time, End time, Start date, and End date.

Alarm - Press

to activate the fields for Alarm time and Alarm date.

to change the entry to be repeated. Shown with in

Repeat - Press

the Day view.

•

Repeat until - Set an ending date for the repeated entry, for example, the

last date of a weekly course you are taking. This option is shown only if you

have selected to repeat the event.

Synchronisation - Private - After synchronisation the calendar entry can be

seen only by you and it will not be shown to others even if they have online

access to view the calendar. Public - The calendar entry is shown to others

who have access to view your calendar online. None - The calendar entry

will not be copied when you synchronise your calendar.

3. To save the entry, press Done.

To edit or delete a repeated entry, choose how you want the changes to take

effect: All occurrences - all repeated entries are changed Thisentryonly - only the

current entry is changed.

Calendar views

Options in the different calendar views: Open, New entry, Week view/

Month view, Delete, Go to date, Send, Settings, Help, and Exit.

Press

date.

in the Month, Week, or Day views to automatically highlight today’s

To write a calendar entry, press any number key (

) in any

calendar view. A Meeting entry is opened and the characters you keyed in are

added to the Subject field.

•

To go to a certain date, select Options→Go to date. Write the date and press

OK.

•

Icons in Day and Week views:

Synchronisation icons in Month view:

- Private, - Public, - None, and

entry.

- Memo and

- Anniversary.

- the day has more than one

■ To-do

Go to Menu→To-do.

In To-do, you can keep a list of tasks that you need to do. The To-do list uses

shared memory. See “Shared memory” on page 16.

1. To start to write a to-do note, press any number key (

editor opens and the cursor blinks after the letters you have keyed in.

2. Write the task in the Subject field. Press to add special characters.

To set the due date for the task, scroll to the Due date field and key in a

). The

•

date.

To set a priority for the to-do note, scroll to the Priority field and press

3. To save the to-do note, press Done. If you remove all characters and press

Done, the note is deleted, even if you edit a previously saved note.

•

To open a to-do note, scroll to it and press

To delete a to-do note, scroll to it and select Options→Delete or press

•

To mark a to-do note as completed, scroll to it and select Options→Mark as

done.

To restore a to-do note, select Options→Mark as not done.

■ Importing data from compatible Nokia phones

You can move calendar, contacts, and to-do data from compatible Nokia phones

to your phone using the Nokia PC Suite 6.2 Content Copier application on a

compatible PC. Instructions for using the application can be found in the help

function of PC Suite on the CD-ROM.

6. Media

■ Camera

To start the Camera application, turn the phone into Imaging

mechanical mode. Alternatively, when the phone is in standby mode either in

Work or Browse mechanical mode, go to Menu→Camera.

You can take photos and record video clips with the phone’s built-in Camera

application. The images are automatically saved in the Gallery application, where

you can rename and organise them in folders. See “Gallery” on page 81. The phone

memory or memory card is used to store the image or video, depending on the

Memory in use setting. See “Camera settings” on page 72.

You can also send images in a multimedia message, as an e-mail attachment, or

via Bluetooth technology or infrared connection. The camera produces images in

JPEG and video clips in 3GP file format.

Taking a picture or recording a video clip

Options available before taking a picture when the phone is either in Work

or Browse mechanical mode: Record/Capture, Mode, Go to Gallery, Settings, Help,

and Exit.

Note that these options are not available when the phone is in Imaging

mechanical mode.

1. Turn the fold to Imaging mechanical mode. You can also use the Camera

application in Work or Browse mechanical mode.

2. Press

to select the camera mode (Standard, Portrait, Night or

Video). By default, the camera is in Standard mode.

Note that when the phone is in Imaging mechanical mode, you need to press

to go left or

to go right to select the camera mode.

Note that selection keys are not functional in the Imaging mechanical mode,

or in the Standard or Video camera mode. Use

and for Camera

functions.

You can see the viewfinder and the cropping lines, which show you the image

area to be captured or recorded.

You can also see the recording counter, which shows the recorded time, or the

image counter, which shows you how many images, depending on the selected

picture quality, fit in the memory of your phone or memory card, if you use one.

3. To take a picture, press

quickly. When you are taking a picture, do not move

the phone before the Camera application starts to save the image. The camera

shows the image and saves it automatically in Gallery. To return to the

viewfinder, press

again quickly. To take another picture, press

again.

4. To start recording a video clip, make sure you have first selected the Video

mode. Then press

press

quickly to start recording. To pause recording at any time,

quickly again.

quickly. To resume recording, press

5. To stop recording, press and hold

for a few seconds.

6. Press to zoom in on your subject before or while taking the picture or

recording a video clip. Press to zoom out. The zoom indicator on the display

shows the zoom level.

The camera goes into battery saving mode if there has been no key presses within

a minute. To continue taking pictures, press

You can insert an image into a contact card. See “Managing contacts” on page 54.

Image size and orientation

With the different camera modes, you can select the size and orientation of the

picture to be taken.

•

Standard - Take normal landscape pictures.

Portrait - Take a smaller icon-sized, vertical picture, which can be added to a

contact card.

•

Night - The lighting is dim and the camera needs a longer exposure time for

the picture to be of good quality. Note that, in dim conditions, any movement

while taking a picture may cause it to be blurred. The image size and

orientation is the same for Standard and Night.

•

Video - Record a video clip.

The actual image pixel size depends on the selected camera mode and the phone’s

mechanical mode. See “Mechanical modes” on page 23.

•

Pictures taken in Standard or Night mode are saved in 480x360 pixel format in

the Work and Imaging mechanical modes and 640x480 pixel format in the

Browse mechanical mode.

•

Pictures taken in Portrait mode are saved in 80x96 pixel format.

Video clips are saved in 128x96 (sub-QCIF) pixel format.

Camera settings

Go to Options→Settings.

In the Camera application settings, you can adjust the image quality setting,

change the default image name, and change the memory location of saved

images.

1. Scroll to the setting you want to change:

•

Image quality - High, Normal, and Basic. The better the image quality, the

more memory the image consumes.

•

Default image name - By default, the camera names images in the format

‘Image.jpg’. Default image name allows you to set a name for the images

stored.

•

Audio - On and Off. When the video sound is on, the maximum recording

time is shorter than with sound off. Note that this option is only available in

Video mode.

Default video name - By default, the camera names video clips in the

format ‘Video.3gp’. Default video name allows you to set a name for the

video clips stored.

•

Memory in use - Select whether you want to store your images and video

clips in the phone memory or on the memory card, if you use one.

VGA resolution - Select On to set the camera to take all the pictures in VGA

mode (480 x 640 pixels). This option is available for Standard, Portrait, and

Night modes.

2. Press Options→Change to change the selected setting.

Viewing images

Go to Menu→Gallery.

Pictures taken with the Camera application are stored as images in the Gallery.

See “Gallery” on page 81. Images can be sent to you in a multimedia or picture

message, as an e- mail attachment, or via a Bluetooth connection. After receiving

an image in the Inbox, you need to save it in the phone memory or on a memory

card. You can save graphics sent to you in picture messages to the Picture

messages folder. See “Picture messages folder” on page 82.

Options when viewing an image: Send, Set as wallpaper, Rotate, Zoom in,

Zoom out, Full screen, Delete, Rename, View details, Add to 'Go to', Help, and Exit.

Select an image from the list of images in the Images folder in the Gallery to start

the image viewer and display the image.

When viewing an image, pressing

image in the current folder.

takes you to the next or previous

In the images thumbnail view:

1. Press or to move between the phone and memory card.

2. To browse the list of images, press and

3. Press to open an image. When the image is open, you can see the name of

the image.

You can view animated GIF files in the same way as other images.

Zooming on a saved image

1. Select Options→Zoom in or Zoom out. You can see the zooming ratio at the

top of the display. See “Shortcuts during zooming” on page 74.

2. Press

permanently.

When you select Options→Full screen, the panes around the image are removed

so that you can see more of the image. Press to return to the initial view.

to return to the initial view. The zooming ratio is not stored

When you are zooming in on an image, use the scroll key to move the focus to the

left, right, up, or down, so that you can take a closer look at one part of the image,

for example, its upper right corner.

Shortcuts during zooming

•

Rotate 90 degrees:

rotation status is not stored permanently.

- zoom in, - zoom out, press and hold to return to normal view.

- anticlockwise,

- clockwise. The

•

- change between full screen and normal view.

■ RealPlayer™

Go to Menu→RealPlayer.

With RealPlayer™, you can play local media files stored in the phone

memory, or memory card, or stream media files over the air from a streaming link.

The streaming link can be activated during a browsing session or stored in the

phone memory or memory card.

Media files are video, music or audio clips. Files with the extensions .3gp, .aac,

.amr, .mp3, .mp4, .rm and .ram are supported by RealPlayer.

RealPlayer does not necessarily support all file formats or all the variations of a

file formats. For example, RealPlayer attempts to open all .mp4 files. However,

some .mp4 files may include content that is not compliant with 3GPP standards

and, therefore, is not supported by this phone. In this case, the operation might

fail and result in partial playback or in an error message.

RealPlayer uses shared memory. See “Shared memory” on page 16.

Options in RealPlayer when a clip has been selected: Play, Continue, Stop,

Mute, Unmute, Clip details, Send, Settings, Help, and Exit.

Playing media files

To play a media file stored in your phone’s memory or memory card, scroll to the

file and press

to play it, or go to RealPlayer and select Options→ Open and:

•

Most recent clips - To play one of the last six files played in RealPlayer, or

Saved clip - To play a file saved in the Gallery. See “Gallery” on page 81.

To stream content over the air:

•

Select a streaming link saved in the Gallery. Before your live content begins

streaming, your phone connects to the site and loads the file.

•

Open the link to a file in the browser.

To stream live content, you must first configure your default access point. See

“Access points” on page 133.

Many service providers require you to use an Internet Access Point (IAP) for your

default access point. Other service providers allow you to use a WAP access point.

Contact your service provider for more information.

Note: In RealPlayer, you can only open an rtsp:// URL address. You cannot

open an http:// URL address; however, RealPlayer recognises an http link

to a .ram file since a .ram file is a text file containing an rtsp link.

Warning: Do not hold the device near your ear when the loudspeaker is in use,

because the volume may be extremely loud.

Shortcuts during play

When a media file is playing use the scroll key to seek (move quickly through the

media file), and to mute the sound, as follows:

Press and hold

to seek forwards, or press and hold

to seek backwards

through the media file.

Press and hold

until the indicator is displayed to mute the sound.

until you see the indicator to turn on the sound.

Changing the settings

Go to Options→Settings→Video or Connection.

Press

Connection.

Select Video to change the following list of settings:

to move between the different setting tabs for Video and

•

Contrast - Open the slider view to change the contrast.

Repeat - Choose On to have the currently playing video or audio file restart

automatically once it has finished.

Select Connection to change the connection settings.

■ Radio

Go to Menu→Radio.

You can listen to FM radio on your phone via the built-in

loudspeaker or a compatible headset. When using the loudspeaker, keep the

headset plugged into the phone. The lead of the headset functions as the antenna

of the radio, so let it hang freely.

The FM radio uses the wire of the headset as an antenna. A compatible headset needs to be

attached to the device for the FM radio to function properly.

Warning: Listen to music at a moderate level. Continuous exposure to high volume

may damage your hearing.

You can make or answer a call while listening to the radio. The volume of the radio

is muted. When you end the call, the radio is automatically turned on. Sending or

receiving data over an (E)GPRS or HSCSD connection may interfere with the radio.

Note that the quality of the radio broadcast depends on the radio station’s

coverage in that particular area.

1. To turn on the radio, press Menu→Radio. On the display shows

•

Channel location number and the name of the radio channel.

Frequency of the last used radio channel.

2. If you have previously saved radio channels, scroll to the channel you want to

listen to, or select the memory location of a channel by pressing the

corresponding key 1 to 9.

The display shows four graphic buttons:

•

and

. Select to scroll to the next or previous saved channel. The

buttons are inactive if there are no saved channels.

•

and . Select to start automatic tuning upwards or downwards.

When using a compatible headset, press the headset key to scroll to the desired

saved radio channel.

3. To turn the radio off, press Exit.

Tuning and saving a radio channel

When the radio is on, press and hold

to start the channel search.

Searching stops when a channel is found. To save the channel, press Options, and

select Savechannel. Select a location for the channel with the

and

buttons

and press Select. Key in the name of the channel and press OK.

Using the radio

When the radio is on, press Options and select

•

Channels - Open the channel list. See “Using the channel list” on page 80.

Activate loudsp. - Listen to the radio using the integrated handsfree (IHF). The

integrated handsfree allows you to speak and listen to radio or audio files

without having to hold the phone to the ear. When the integrated handsfree is

activated, the headset is muted.

•

Deactivate loudsp. - Listen to the radio using the headset.

Auto tune up and Auto tune down - Start the channel search upwards or

downwards. When a channel is found, the search stops and the channel is

played. To save the channel, see Save channel below.

•

Manualtuning - Set the channel frequency manually. Briefly press

move the channel search 0.05 MHz upwards or downwards, or press and hold

down the keys to quickly search upwards or downwards for a channel. To save

the channel, press OK and see Save channel below.

If you know the frequency of the radio channel you would like to listen to

(between 87.5 MHz and 108.0 MHz), key it in and press OK.

•

Save channel - S a v e t he radio channel you have found. R e fer Tuning and

saving a radio channel on page 79. Up to 19 radio channels can be saved.

•

Help - Open the context-sensitive help.

Exit - Turn off the radio.

Using the channel list

Go to Options→Channels.

The channel list is used for managing the saved radio channels. The list contains

19 channels. When you open the list, the currently active channel is highlighted if

it is saved. Otherwise, the first saved channel is highlighted.

Press Options and select

•

Listen - Listen to the selected channel.

Activate loudsp. - Listen to the radio using the integrated handsfree (IHF).

Deactivate loudsp. - Listen to the radio using the headset.

Auto-save channels - Save all available stations to the channel list. Note that

this replaces your currently saved stations. Channels are sought and saved

starting from the lowest frequency (87.5 MHz) and position 1 even if saved

channels exist in the list. The automatic channel saving saves all clearly

audible stations or until all 19 positions are filled. The channel names are left

empty, so the channel list only shows the channel frequencies.

•

Rename - Change the name of the highlighted channel. Key in the channel

name and press OK.

•

Delete - Delete the highlighted channel from the channel list.

Help - Open the context-sensitive help.

Exit - Turn off the radio.

■ Gallery

Go to Menu→Gallery.

Use the Gallery to store and organise your images, sound clips, playlists, video

clips, streaming links and RAM files.

The Gallery uses shared memory. See “Shared memory” on page 16.

Open the Gallery to see a list of the folders in the phone memory. Press

the folders on the memory card, if you use one.

to see

Select a folder Images, Sound clips, or Video clips (or other folder that you have

created) and press

to open it.

In the open folder you can see:

•

an icon depicting the type of each file in the folder, or in the case of an image,

a small thumbnail picture which is a preview of the image

•

the name of the file

the date and time a file was saved or the size of the file

subfolders, if present.

Options: Open (folder or item), Send, Delete, Create new, Move to folder,

New folder, Mark/Unmark, Rename, Gallery downloads, Image uploader, Receive

via infrared, View details, Add to 'Go to', Settings, Help, and Exit.

You can browse, open, and create folders, as well as mark, copy and move items to

folders. See “Actions common to all applications” on page 30.

being copied, modified, transferred or forwarded.

Opening files

Select any file and press

application as follows:

to open it. Each file opens in its corresponding

•

Images - open in the Image viewer. See “Viewing images” on page 73.

Sound clips - open and play in the RealPlayer application. See “RealPlayer™” on

page 75.

•

Video clips, RAM files, and streaming links - Open and play in the RealPlayer

application. See “RealPlayer™” on page 75.

Subfolders - open to display contents.

Other default folders

Picture messages folder

Use this folder to store pictures sent to you in picture messages.

•

Select the folder Images→Picture msgs..

Options in the Picture messages folder: Open, Send, Delete, Mark/Unmark,

Rename, View details, Help, and Exit.

To save a picture that you have received in a picture message, go to

Messaging→Inbox, open the message, and select Options→Save picture.

Wallpapers folder

Use this folder to store pictures that you want to use as background images for

multimedia messages.

•

Select the folder Images→Wallpapers.

Presence logos folder

Use this folder to store logos for Presence. See “Presence” on page 58.

•

Select the folder Images→Presence logos.

Downloading files

Go to Options→Gallery downloads.

Choose from Graphic downloads, Video downloads, or Tone downloads. The

browser opens and you can choose a bookmark for the site to download from. See

“Viewing bookmarks” on page 162.

To download files, you must first configure your default access point. See “Access

points” on page 133. For more information on downloading, See “Downloading”

on page 165..

Once items have been downloaded, the browser closes and the phone returns to

Gallery view.

Uploading images to an image server

Go to Options→Image uploader.

You can send your pictures to an image server to allow others to share your

pictures online (network service).

Before you can upload images, you must enter the settings for the image server.

You can get these settings from your service provider.

Setting up the image server

1. Select Settings→Image servers and press

. Fill in the details for each

field. See “Access points” on page 133.

2. Press

Uploading images

1. To begin an upload, mark the images and select Upload.

2. Enter the name of the folder on the image server that the images are stored in

and press

7. Messaging

Go to Menu→Messaging.

In Messaging you can create, send, receive, view, edit, and organise text messages,

multimedia messages, e-mail messages, presentations, documents, smart

messages, and special text messages containing data. You can also receive

messages and data via an infrared or Bluetooth technology connection, receive

service messages, cell broadcast messages, and send service commands.

Note that only devices that offer picture message features can receive and display

picture messages.

Text messages and multimedia messages use shared memory. See “Shared

memory” on page 16.

Your device supports the sending of text messages beyond the normal 160-character limit. If

your message exceeds 160 characters, it will be sent as a series of two or more messages.

Note that each message will be invoiced separately according to your service provider’s

rates.

In the navigation bar, you can see the message length indicator counting backwards from

160. For example, 10 (2) means that you can still add 10 characters for the text to be sent as

two messages.

Note that using special (Unicode) characters such as ë, â, á, ì take up more space.

If there are special characters in your message, the indicator may not show the message

length correctly. Before the message is sent, the device tells you if the message exceeds the

maximum length allowed for one message. You can cancel sending by pressing Cancel or

you can save the message in the inbox.

Options in the Messaging main view are: Create message, Connect (shown

if you have defined settings for the mailbox), or Disconnect (shown if there is an

active connection to the mailbox), SIM messages, Cell broadcast, Service

command, Settings, Help, and Exit.

When you open Messaging, you can see the New message function and a list of

default folders:

Inbox - Contains received messages except e-mail and cell broadcast

messages. E-mail messages are stored in the Mailbox. You can read cell broadcast

messages by selecting Options→Cell broadcast.

My folders - For organising your messages into folders.

Mailbox - When you open this folder, you can either connect to your remote

mailbox to retrieve your new e-mail messages or view your previously retrieved e-

mail messages offline. After you have defined settings for a new mailbox, the

name given to that mailbox replaces Mailbox in the main view. See “E-mail

messages” on page 101.

Drafts - Stores draft messages that have not been sent.

Sent - Stores the last 20 messages that have been sent. You can change the

number of messages to be saved. See “Settings for the Other folder” on page 104.

Messages or data that have been sent via an infrared or Bluetooth technology

connection are not saved in the Draft or Sent folders.

Outbox - Is a temporary storage place for messages waiting to be sent.

Reports (network service) - You can request the network to send you a

delivery report of the text messages, smart messages, and multimedia messages

you have sent. To turn on delivery report reception, select

Options→Settings→Text message or Multimedia message, scroll to Receive

report, and select Yes.

Receiving a delivery report of a multimedia message that has been sent to an e-

mail address might not be possible.

■ Writing and sending messages

Go to Menu→Messaging.

Options in the text message editor: Send, Add recipient, Insert, Delete,

Check contacts, Message details, Sending options, Help, and Exit.

Before you can create a multimedia message, or write an e-mail, or connect to

your remote mailbox, you must have the correct connection settings in place. See

“Settings for e-mail” on page 89. See “Settings for multimedia” on page 89.

1. Select New message. A list of message options opens. Select:

•

Create:→Text message to create a text message.

To send a picture message, select Options→Insert→Picture.

Each picture message is made up of several text messages. Therefore,

sending one picture message may cost more than sending one text

message.

•

Create:→Multimedia message to send a multimedia message (MMS).

content from being copied, modified, transferred or forwarded.

Create:→E-mail to send e-mail. If you have not set up your e-mail account,

you are prompted to do so.

To add a media object to an e-mail, select Options→Insert→Image, Sound

clip, Video clip, Note or Template.

2. Press

to select the recipient(s) from the Contacts directory or write the

phone number or e-mail address of the recipient in the To: field if you are

sending an MMS or e-mail to the recipient. Press

to separate each recipient.

to add a semicolon (;)

3. Press

to move to the message field.

4. Write the message.

•

To add a media object to a multimedia message, select Options→Insert

object→Image, Sound clip or Video clip. To add a new media object, select

Options→Insert new→Image, Sound clip, Video clip or Slide. Select the

item you wish to add. When sound has been added, the

icon is shown

in the navigation bar. If you select Insert new→Sound clip, Recorder opens

and you can record a new sound. The sound is automatically saved and a

copy is inserted in the message.

5. To send the message, select Options→Send or press

Note: Picture message function can be used only if it is supported by your network

operator or service provider. Only devices that offer picture message features can

receive and display picture messages.

Only devices that offer compatible multimedia message or e-mail features can

receive and display multimedia messages.

Settings for multimedia

Go to Options→Settings→Multimedia message.

Open Access point in use and select the access point you created. See “Multimedia

messages” on page 99.

You may receive the settings as a smart message from your network operator or

service provider. See “Receiving smart messages” on page 91.

For availability of and subscription to data services, contact your network

operator or service provider.

The default setting of the multimedia message service is generally on.

The appearance of a multimedia message may vary depending on the receiving device.

Settings for e-mail

Before you can send, receive, retrieve, reply to, and forward e-mail to a separate

e-mail account, you must:

•

Configure an Internet Access Point (IAP) correctly. See “Connection settings”

on page 133.

•

Define your e-mail settings correctly. See “E-mail messages” on page 101.

Follow the instructions given by your remote mailbox and Internet service

provider.

■ Inbox - receiving messages

Go to Menu→Messaging→Inbox.

Options in the Inbox: Open, Create message, Delete, Message details, Move

to folder, Mark/Unmark, Help, and Exit.

When there are unread messages in Inbox, the icon changes to

In Inbox, the message icons tell you what kind of a message it is. Here are some of

the icons that you may see:

indicates an unread text message and

message

indicates an unread smart

indicates an unread multimedia message

indicates an unread WAP service message

indicates data received via infrared

indicates data received via Bluetooth technology

indicates an unknown message type.

Viewing multimedia objects

Options in the Objects view are: Open, Save, Send, Call, and Exit.

To see what kinds of media objects have been included in the multimedia

message, open the message and select Options→Objects. In the Objects view you

can view files that have been included in the multimedia message. You can choose

to save the file in your phone or to send it, for example, via infrared or Bluetooth

technology to another compatible device.

Important: Exercise caution opening messages. M e ssages may contain malicious

software or otherwise be harmful to your device or PC.

Receiving smart messages

Your phone can receive many kinds of smart messages, text messages that contain

data (also called Over-The-Air (OTA) messages). See “Settings for multimedia” on

page 89. and See “Settings for e-mail” on page 89. for more information on your

phone settings. To open a received smart message, open the Inbox, scroll to the

smart message (

), and press

•

Picture message - To save the picture in the Picture messages folder in the

Gallery for later use, select Options→Save picture.

•

Business card - To save the contact information, select Options→Save

business card.

•

Ringing tone - To save the ringing tone to the Gallery, select Options→Save.

Operator logo - To save the logo, select Options→Save. The operator logo can

now be seen in standby mode instead of the network operator’s own

identification.

•

Calendar entry - To save the invitation to the Calendar, select Options→Save

to Calendar.

•

Web message - To save the bookmark, select Options→Save tobookmarks. The

bookmark is added to the Bookmarks list in browser services.

If the message contains both browser access point settings and bookmarks, to

save the data select Options→Save all. Or, select Options→View details to

view the bookmark and access point information separately. If you do not want

to save all the data, select a setting or bookmark, open the details, and select

Options→Save to Settings or Save to bookmarks depending on what you are

viewing.

•

E-mail notification - Tells you how many new e-mails you have in your remote

mailbox. An extended notification may list more detailed information such as

subject, sender, attachments, and so on.

In addition, you can receive a text message service number, voice mailbox

number, profile settings for remote synchronisation, access point settings for

the browser, multimedia messaging or e-mail, access point login script

settings, or e-mail settings.

To save the settings, select Options→Save to SMS sett., Save to Voice mail,

Save to Settings, or Save to e-mail sett..

Receiving service messages

Service messages (network service) are notifications of, for example, news

headlines, and they may contain a text message or the address of a browser

service. For availability and subscription, contact your service provider.

■ My folders

Go to Menu→Messaging→My folders.

In My folders, you can organise your messages into folders, create

new folders, and rename and delete folders.

■ Mailbox

Go to Menu→Messaging→Mailbox.

When you open this folder, you can connect to your remote mailbox (network

service) to:

•

retrieve new e-mail headings or messages, or

view your previously retrieved e-mail headings or messages offline.

When you scroll to your mailbox and press

, the phone asks you if you want

to Connect to mailbox? Select Yes to connect to your mailbox or No to view

previously retrieved e-mail messages offline.

Another way to start a connection is to select Options→Connect.

If you select New message→Create:→E-mail or Mailbox in the Messaging main

view and you have not set up your e-mail account, you are prompted to do so. See

“Settings for e-mail” on page 89.

When you create a new mailbox, the name you give to the mailbox automatically

replaces Mailbox in the Messaging main view. You can have several mailboxes

(max. six).

When you are online, select Options→Disconnect to end the data call or GPRS

connection to the remote mailbox.

Retrieving e-mail messages from the mailbox

Go to Options→Connect.

This starts a connection to a remote mailbox.

1. When you have an open connection to a remote mailbox, select

Options→Retrieve e-mail→:

•

New - To retrieve all new e-mail messages to your phone.

Selected - To retrieve only the e-mail messages that have been marked. Use

the Mark/Unmark→Mark/Unmark commands to select messages one by

one. See “Actions common to all applications” on page 30.

•

All - To retrieve all messages from the mailbox.

To cancel retrieving, press Cancel.

2. After you have retrieved the e-mail messages, you can continue viewing them

online. Select Options→Disconnect to close the connection and to view the e-

mail messages offline.

3. To open an e-mail message, scroll to the e-mail you want to view and press

. If the e-mail message has not been retrieved (arrow in the icon is

pointing outwards) and you are offline and select Open, you are asked if you

want to retrieve this message from the mailbox.

•

To view e-mail attachments, open a message that has the attachment

indicator and select Options→Attachments. In the Attachments view,

you can retrieve, open, or save attachments, in supported formats. You can

also send attachments via infrared or Bluetooth technology.

If your mailbox uses the IMAP4 protocol, you can decide whether to

retrieve e-mail headings only, messages only, or messages and

attachments. With the POP3 protocol, the options are e-mail headings only

or messages and attachments. See “E-mail messages” on page 101.

Important: Exercise caution opening messages. Messages may contain malicious

software or otherwise be harmful to your device or PC.

Deleting e-mail messages

•

To delete an e-mail from the phone while still retaining it in the remote

mailbox:

Select Options→Delete→Phone only.

The phone mirrors the e-mail headings in the remote mailbox. So, although

you delete the message content, the e-mail heading stays in your phone. To

remove the heading as well, delete the e-mail message from your remote

mailbox first and then make a connection from your phone to the remote

mailbox again to update the status.

•

To delete an e-mail from both the phone and the remote mailbox:

Select Options→Delete→Phone and server.

If you are offline, the e-mail is deleted first from your phone. During the next

connection to the remote mailbox, it is automatically deleted from the remote

mailbox. If you are using the POP3 protocol, messages marked to be deleted are

removed only after you have closed the connection to the remote mailbox.

•

To cancel deleting an e-mail from both the phone and server, scroll to an e-

mail that has been marked to be deleted during the next connection ( ), and

select Options→Undelete.

■ Outbox

Go to Menu→Messaging→Outbox.

The Outbox is a temporary storage place for messages that are waiting to be sent.

Status of the messages in the Outbox:

•

Sending - A connection is being made and the message is being sent.

•

Waiting/Queued - For example, if there are two similar types of messages in

the Outbox, one of them waits until the first one is sent.

•

Resend at ... (time) - Sending has failed. The phone tries to send the message

again after a time-out period. Press Send if you want to restart the sending

immediately.

•

Deferred - You can set documents to be ‘on hold’ while they are in the Outbox.

Scroll to a message that is being sent and select Options→Defer sending.

Failed - The maximum number of sending attempts has been reached. If you

were trying to send a text message, open the message and check that the

Sending settings are correct.

Note: When sending messages, your device may display the words “Message Sent”.

This is an indication that the message has been sent by your device to the message

centre number programmed into your device. This is not an indication that the

message has been received at the intended destination. For more details about

messaging services, check with your service provider.

■ Viewing messages on a SIM card

Before you can view SIM messages, you need to copy them to a folder in your

phone. See “Actions common to all applications” on page 30.

■ Cell broadcast

Go to Menu→Messaging→Options→Cell broadcast.

You may be able to receive messages on various topics, such as weather

or traffic conditions from your service provider (network service). For available

topics and relevant topic numbers, contact your service provider. In the main view,

you can see:

•

the status of the topic:

- for new, subscribed messages and

- for new, unsubscribed messages.

Options in Cell broadcast: Open, Subscribe/Unsubscribe, Hotmark/Remove

hotmark, Topic, Settings, Help, and Exit.

•

the topic number, topic name, and whether it has been flagged ( ) for follow-

up. You will be notified when messages belonging to a flagged topic have

arrived.

A packet data (GPRS) connection may prevent cell broadcast reception. Contact

your network operator for the correct GPRS settings.

■ Service command editor

Go to Menu→Messaging→Options→Service command. Key in

and send service requests (also known as USSD commands) such as

activation commands, for network services, to your service provider.

■ Messaging settings

Go to Menu→Messaging→Options→Settings.

Text messages

Go to Text message. The following list of settings opens:

•

Message centres - Lists all the defined message centres.

Options when editing message centre settings: New msg. centre, Edit,

Delete, Help, and Exit.

•

Msg. centre in use (Message centre in use) - Defines which message centre is

used for delivering text messages and smart messages such as picture

messages.

•

Receive report (delivery report) - When this network service is set to Yes, the

status of the sent message (Pending, Failed, Delivered) is shown in the Reports

(Network Service).

Receiving a delivery report of a multimedia message that has been sent to an

e-mail address might not be possible.

•

Message validity - If the recipient of a message cannot be reached within the

validity period, the message is removed from the message service centre. Note

that the network must support this feature. Maximum time is the maximum

amount of time allowed by the network for which the message remains valid.

•

Message sent as - The options are Text, Fax, Paging, and E-mail. For further

information, contact your network operator.

Preferred connection - You can send text messages via the normal GSM

network or via GPRS, if supported by the network.

Reply via same ctr.(network service) - By setting this option to Yes, if the

recipient replies to your message, the return message is sent using the same

message service centre number. Note that not all network services provide this

option. For availability, contact your network operator or service provider.

Multimedia messages

Go to Multimedia message. The following list of settings opens:

•

Accesspoint inuse (Must be defined) - Select which access point is used as the

preferred connection for the multimedia message centre. See “Settings for

multimedia” on page 89.

If you receive multimedia message settings in a smart message and save them, the

received settings are automatically used for the Access point. See “Receiving

smart messages” on page 91.

•

Multimedia reception - Select:

•

Only in home net. - To receive multimedia messages only when you are in

your home network. When you are outside your home network, multimedia

message reception is turned off.

•

Always on - To always receive multimedia messages.

Off - Not to receive multimedia messages or advertisements at all.

On receiving msg. - Select:

•

Retr. immediately - To let the phone try to retrieve multimedia messages

instantly. If there are messages with Deferred status, they are retrieved as

well.

Defer retrieval - To let the multimedia messaging centre save the message

to be retrieved later. To retrieve the message, set On receiving msg. to Retr.

immediately.

Reject message - To reject multimedia messages. The multimedia message

centre deletes the messages.

•

Allow anon. messages - Select No to reject messages coming from an

anonymous sender.

Receive adverts - Define whether you want to allow reception of multimedia

message advertisements or not.

Reports - Set to Yes, if you want the status of the sent message (Pending,

Failed, Delivered) to be shown in the Reports.

100

•

Deny report sending - Choose Yes, if you do not want your phone to send

delivery reports of received multimedia messages.

Message validity (network service) - If the recipient of a message cannot be

reached within the validity period, the message is removed from the

multimedia message centre. Maximum time is the maximum amount of time

allowed by the network for which the message remains valid.

•

Image size - Define the size of the image in a multimedia message. The options

are: Small (max. of 160x120 pixels) and Large (max. 640x480 pixels).

The default setting of the multimedia message service is generally on.

The appearance of a multimedia message may vary depending on the receiving device.

E-mail messages

Go to E-mail.

Open Mailbox in use to select which mailbox you want to use.

Settings for Mailboxes

Options when editing e-mail settings: Editing options, New mailbox,

Delete, Help, and Exit.

Select Mailboxes to open a list of defined mailboxes. If no mailboxes have been

defined, you are prompted to do so. The following list of settings is shown (this

information is available from your e-mail service provider):

•

Mailbox name - Write a descriptive name for the mailbox.

101

•

Access point inuse (Must be defined) - The Internet Access Point (IAP) used for

the mailbox. Choose an IAP from the list. See “Connection settings” on

page 133.

My e-mail address (Must be defined) - Write the e-mail address given to you

by your service provider. The address must contain the @ character. Replies to

your messages are sent to this address.

•

Outgoing mail server: (Must be defined) - Write the IP address or host name of

the computer that sends your e-mail.

Send message (network service) - Define how e-mail is sent from your phone.

Immediately - The phone tries to connect to the mailbox immediately after you

have selected Send. During next conn. - E-mail is sent the next time you

connect to your remote mailbox.

•

Send copy to self - Select Yes to save a copy of the e-mail to your remote

mailbox and to the address defined in My e-mail address.

Include signature - Select Yes to attach a signature to your e-mail messages

and to start to write or edit a signature text.

•

User name: - Write your user name, provided by your service provider.

Password: - Write your password. For increasing security, you can leave this

field blank, so that every time you try to connect to your remote mailbox, you

are prompted for the password Otherwise the password is sent automatically.

•

Incoming mail server: (Must be defined) - The IP address or host name of the

computer that receives your e-mail.

102

•

Mailbox type: - Defines the e-mail protocol your remote mailbox service

provider recommends. The options are POP3 and IMAP4.

This setting can be selected only once and cannot be changed if you have

saved or exited from the mailbox settings.

•

Security - Used with the POP3, IMAP4, and SMTP protocols to secure the

connection to the remote mailbox.

APOP secure login - Used with the POP3 protocol to encrypt the sending of

passwords to the remote e-mail server. Not shown if IMAP4 is selected for

Mailbox type:.

•

Retrieve attachments (not shown if the e-mail protocol is set to POP3) - To

retrieve e-mail with or without attachments.

Retrieve headers - To limit the number of e-mail headers you want to retrieve

to your phone. The options are All and User defined. Used with the IMAP4

protocol only.

Service messages

Go to Service message. The following list of settings opens:

•

Service messages - Choose whether or not you want to allow reception of

service messages.

Authentic. needed - Choose to receive service messages only from authorised

sources.

103

Cell broadcast

Check with your service provider whether Cell broadcast (network service) is

available and what the available topics and related topic numbers are.

Go to Cell broadcast to change the settings:

•

Reception - On or Off.

Language - All allows you to receive cell broadcast messages in every possible

language. Selected allows you to choose in which languages you wish to

receive cell broadcast messages. If the language you prefer could not be found

in the list, select Other.

•

Topic detection - If you receive a message that does not belong to any of the

existing topics, Topic detection→On allows you to save the topic number

automatically. The topic number is saved to the topic list and shown without a

name. Choose Off if you do not want to save new topic numbers automatically.

Settings for the Other folder

Go to Other. The following list of settings opens:

•

Save sent messages - Choose to save a copy of every text message, multimedia

message, or e-mail that you have sent to the Sent items folder.

No. of saved msgs. - Define how many sent messages are saved to the Sent

items folder at a time. The default limit is 20 messages. When the limit is

reached, the oldest message is deleted.

104

■ Chat

Go to Menu→Chat.

Options in the Chat main view are: Open, Login, Logout, Settings, Help, and

Exit.

Chat (network service) allows you to converse with other people using instant

messages, and join discussion forums (chat groups) with specific topics. Once you

have registered with a chat service, you can log into the service provider’s chat

server.

Check the availability of chat services, pricing, and tariffs with your network

operator and/or service provider. Service providers also give you instructions on

how to use their services.

To access a chat service you need to save the settings for that service. You may

receive the settings from the network operator or service provider that offers the

service. See “Receiving smart messages” on page 91. You can also key in the

settings manually. See “Chat and Presence servers” on page 113.

Connecting to a chat server

Go to Menu→Chat.

1. The phone automatically tries to connect to a chat server. You can change the

chat server to connect to. See “Chat and Presence servers” on page 113.

2. Once the connection has been established, key in your user ID and password

and press

, or press Cancel to stay offline. When you are offline, your

105

phone is not connected to the chat server and you cannot send or receive

messages. To log in later, select Options→Login.

You obtain the user ID and password from your service provider.

To log out, select Options→Logout.

Modifying your chat settings

Go to Options→Settings→Chat settings.

•

Use screen name - Select Yes to key in a nickname (max. 10 characters).

Chat presence - Prevent others from seeing if you are online, select Not active.

Allow messages from - Select All, From chat contacts or None.

Allow invitations from - Select All, From chat contacts or None.

Message speed - Select the speed at which new messages are displayed.

Availabilityreloading - Choose how to update information about whether your

chat contacts are online or offline. Select Automatic or Manual.

•

Reload availab. for - Select All contacts or Selected contacts.

Joining and leaving a chat group

Go to Menu→Chat→Chat groups.

A list of chat groups that you have saved or are currently joined to is shown. The

icon next to a group indicates what type it is:

•

- A group that you have created and are currently joined to.

106

•

- A group that you have created but are not currently joined to.

- A group that you have saved and are currently joined to.

- A group that you have saved but are not currently joined to.

Options in the Chat groups view are: Open, Join group, Create new group,

Leave chat group, Chat group, Search, Settings, Help, and Exit.

•

- A group that you are currently joined to but have not saved.

To join a chat group: Scroll to a group on the list and press

group not on the list but for which you know the group ID, select Options→Join

group. Key in the group ID and press

. To join a chat

You can scroll to a group, press Options→Chat group and then select: Save group,

Delete, View participants to see which members are currently joined to the group,

Chat group details to see the group ID, topic, members, editing rights in the group,

and whether sending private messages is allowed in the group, and Chat group

settings to view and edit the chat group’s settings. See “Editing chat group

settings” on page 112.

To leave the chat group: Select Options→Leave chat group.

Searching for chat groups and users

Go to Chat groups→Options→Search→Groups or Users.

•

You can search for Groups by Group name, Topic, and Members (user ID). For

groups that you have found you can select New search, Join and Save group.

107

•

You can search for Users by User's name, User ID, Phone number, and E-mail

address. For users that you have found you can select New search, Open

conversation, Add to Chat contact to save the contact, Send invitation, and

Add to blocked list to block (or unblock) messages from the contact.

When the search result is displayed, you can select Options→New search, More

results from the same search, and Previous results to see your previous search

result.

Chatting in a chat group

Go to Menu→Chat→Chat groups.

Once you have joined a chat group, you can view the messages that are

exchanged in the group, and send your own messages.

Options while chatting: Send, Send private msg., Reply, Send invitation,

Leave chat group, Save group, Record convers./Stop recording, Help, and Exit.

•

To send a message, write the message and press

To send a private message to a member (if allowed in the group), select

Options→Send private msg., select the recipient, write the message, and press

To reply to a private message sent to you, select Options→Reply.

To invite chat contacts who are online to join the chat group (if allowed in the

group), select Options→Send invitation, select the contacts you want to invite,

write the invitation message, and press Done.

108

Recording messages

To record the messages that are exchanged in a chat group or during an individual

conversation, select Options→Record convers.. Key in the name for the message

file and press

. To stop recording, select Options→Stop recording.

The recorded message files are saved to Notes. See “Notes” on page 154.

Blocking messages

To prevent receiving messages from certain chat users, select Options→Blocking

options and then select:

•

Add to blocked list - To block messages from the currently selected user.

Add ID to list manually - Key in the user ID of the user and press

View blocked list - To see the users whose messages are blocked.

Unblock - Select the user that you want to remove from the blocked list and

press

Starting and viewing individual conversations

Go to Menu→Chat→Conversations.

This shows a list of the chat users with whom you have an ongoing conversation.

To start a new conversation, select Options→New conversation and then select:

Options in the Conversations view are: Send, Add to chat contact, Forward,

Record convers./Stop recording, Blocking options, End conversation, Help, and

Exit.

109

•

Select recipient - To see a list of your saved chat contacts that are currently

online. Scroll to the contact and press

Enter user ID - Key in the user ID and press

. The user ID is provided by the

service provider to those who register to the service.

To view an ongoing conversation, scroll to the user and press

. To continue

. To return to the

the conversation, write your message and press

conversations list without closing the conversation, press Back.

To close the conversation, select Options→End conversation.

Icon:

next to a user indicates that you have received a new message from

that user.

Ongoing conversations are automatically closed when you exit Chat.

To save a user to your chat contacts, scroll to the user and select Options→Add to

Chat contact.

To send automatic replies to incoming messages, select Options→Set auto reply

on. Key in the text and press Done.

Chat contacts

Go to Menu→Chat→Chat contacts.

Options in the Chat contacts view are: Open, Open conversation, Switch

tracking on, Belongs to groups, New Chat contact, Edit, Delete, Reload user

availab., Blocking options, Search, Settings, Help, and Exit.

This shows a list of your saved chat contacts.

is shown next to contacts that

are currently online, and indicates contacts that are offline.

110

To create a new contact, select Options→New chat contact. Fill in the Name and

User ID fields and press Done.

You can scroll to a contact and press

and select:

to view contact details. Press Options

•

Edit - Edit the contact’s details.

Open conversation - Start a new conversation or continue an ongoing

conversation with the contact.

•

Switch tracking on - Be notified every time the chat contact goes online or

offline.

•

Belongs to groups - See which groups the chat contact has joined.

Reload user availab. - Update information about whether contacts are online

or offline. This option is not available if you have set the Availability reloading

to Automatic in Chat settings.

Creating a new chat group

Go to Chat groups→Options→Create new group. Key in the settings for the

group:

•

Group name, Group topic, and a Welcome note that the participants see when

they join the group.

•

Group size - Maximum number of members allowed to join the group.

Allow search - Define if others can find the chat group by searching.

111

•

Editing rights - Scroll to the chat group members to whom you want to give

editing rights and permission to invite contacts to join the group.

•

Group members - See “Restricting access to a chat group” on page 112.

Banned - Displays a list of banned users.

Allow private msgs. - Allow or prevent private messaging between members.

Group ID - Is created automatically and cannot be changed.

Editing chat group settings

Go to Menu→Chat→Chat groups.

You can edit the settings for a chat group if you have created the group or if the

creator of the group has given you editing rights. In the Chat groups view, scroll

to the desired group and select Options→Chat group→Chat group settings. See

“Creating a new chat group” on page 111.

Restricting access to a chat group

You can make a chat group closed by creating a Group members list. Only the

users on the list are allowed to join the group. Go to the Chat groups view, scroll

to the group and select Options→Chat group→Chat group settings→Group

members→Selected only.

•

To add a user to the list, select Add and Chat contact or Enter user ID.

To remove a user from the list, scroll to the user and select Remove.

To clear the list and allow all chat users to join the group again select Remove

all.

112

Chat and Presence servers

Go to Options→ Settings→Server settings. You may receive the settings as a

smart message from the service provider that offers the chat service.

•

To change the chat or presence server you wish to connect to, select Default

server.

To change the Presence login type, select Login type and select Automatic, Aut.

in home net., or Manual.

To change the Chat login type, select Login type and select Automatic or

Manual.

To add a new server, select Options→New server. Key in or select the settings:

Server name and Access point in use to connect to the server, Web address of

the chat server, your User ID and login Password. See “Connection settings” on

page 133.

You obtain the user ID and password from your service provider when you

your service provider.

113

8. Tools

■ Applications

Go to Menu→Tools→Manager.

You can install new compatible Symbian operating system applications (SIS files)

and Java™ applications (Java MIDlets and MIDlet suites) on your phone. You can

also update and uninstall applications from the phone, and monitor the

installation history.

Your phone supports J2ME™Java applications. Do not download PersonalJava™

applications to your phone as they cannot be installed.

Options in the Application manager main view are: Install, View details,

View certificate, Update, Go to web address, Remove, View log, Send log, Settings,

App. downloads, Help, and Exit.

Applications in the Application manager use shared memory. See “Shared

memory” on page 16.

When you open the Application manager, you can see a list of:

•

Applications saved in the Application manager.

Partially installed applications (indicated by ).

Fully installed applications that you can remove (indicated by ).

You can only use Symbian operating system applications with a .SIS extension.

114

Downloading an application

Your phone supports J2ME^TMJava applications. Make sure that the application is

compatible with your phone before downloading it. You can download new Java

applications in different ways:

•

Go to Menu→Tools→Manager→App. downloads and the list of available

bookmarks is shown.

Select the appropriate bookmark to connect to the desired page. If the

connection fails, you may not be able to access the page from the service

whose connection settings are currently active. In this case, enter the Web

menu and activate another set of service settings. See “Making a connection”

on page 161. Try again to connect to the page.

For the availability of different services, pricing and tariffs, contact your

network operator and/or the service provider.

•

Go to Menu→Web→Download. Select to download an appropriate

application or game.

Use the Nokia Application installer from PC Suite to download the applications

to your phone.

Important: Only install and use applications and other software from sources that

offer adequate security and protection against harmful software.

Note that when downloading an application, it may be saved in the Games menu

instead of the Web menu.

115

Installing an application

You can install applications that are specifically intended for this phone and

suitable for the Symbian operating system.

If you install an application that is not intended specifically for this phone, it may

function and look different from what was originally intended.

•

Open the Application manager, scroll to the application, and select

Options→Install to start the installation.

•

Alternatively, search the phone memory or the memory card, select the

application, and press

to start the installation.

Applications may be downloaded to your phone during browsing, received as

attachments in multimedia messages or e-mails, or received via infrared or

Bluetooth technology from another device, for example, a phone or a compatible

PC.

Important: Use only services that you trust and that offer adequate security and

protection against harmful software.

To increase protection, the application installation system uses digital signatures

and certificates for applications. Do not install the application if the Application

manager gives a security warning during installation.

If you install an application that contains an update or repair to an existing

application, you can only restore the original application if you have the original

application or a full backup copy of the removed application. To restore the

original application, first remove the updated or repaired application and then re-

install it from the original application or the backup copy.

116

During installation, the phone checks the integrity of the application to be

installed. The phone shows information about the checks being carried out and

you are given options whether to continue or cancel the installation. Once the

phone has checked the integrity of the application, it is installed on your phone.

Installing a Java™application

The .JAR file is required for installation. If it is missing, the phone may ask you to

download it. If there is no access point defined for the Application manager, you

are asked to select one. When downloading the .JAR file, you may need to enter a

user name and password to access the server. You obtain these from the supplier

or manufacturer of the application.

•

To start a data connection and to view extra information about the

application, scroll to it and select Options→Go to web address.

•

To start a data connection and to check if there is an update available for the

application, scroll to it and select Options→Update.

Java settings

•

To change the default access point that a Java application uses for

downloading extra data, select Options→Settings→Access point. See “Access

points” on page 133.

•

To change the security settings that determine the actions that a Java

application is permitted to perform, select Options→Settings.

Not all Java applications permit you to change the security settings.

117

Launching an application

1. Go to Menu→Web→Applications→Select application:.

2. Scroll to an application or an application set (the name depends on the

application).

3. Press Options and select Open or press

. If the selection is a single

application it is launched.

Otherwise, a list of applications in the selected application set is displayed. To

launch a single application, scroll to the desired application and press Options

and select Open, or press

Note that running some applications may consume the phone’s battery faster

(and you may need to connect the phone to the charger).

Other options available for an application or application set

•

Delete - Delete the application or application set from the phone.

•

Application access - Restrict the application from accessing the network.

Select Ask first and the phone asks for net access, Always allowed to allow the

net access, or Not allowed not to allow the net access.

•

Update - Check if a new version of the application is available for download

from the services (network service).

Go to web address - Provide further information or additional data for the

application from an Internet page. This feature needs to be supported by the

network. It is only shown if an Internet address has been provided with the

application.

118

•

Details - Give additional information about the application.

Memory status for applications

Go to Menu→Extras→Memory.

This shows the amount of memory available for game and application

installations.

The applications use shared memory. See “Shared memory” on page 16.

Removing an application

1. To remove an application, scroll to it and select Options→Remove.

2. Press Yes to confirm the removal.

If you remove an application, you can only re-install it if you have the original

application or a full backup of the removed application. If you remove an

application, you may no longer be able to open documents created with that

application. If another application depends on the application that you removed,

the other application may stop working. Refer to the documentation of the

installed application for details.

■ File manager

Go to Menu→Tools→File manager.

In the File manager, you can browse, open, and manage files and folders in the

phone memory or on the memory card, if you use one.

119

Options in the File manager main view are: Open, Send, Delete, Move to

folder, Copy to folder, New folder, Mark/Unmark, Rename, Find, Receive via

infrared, View details, Memory details, Help, and Exit.

Open the File manager to see a list of the folders in the phone memory. Press

to see the folders on the memory card, if you use one.

You can browse, open, and create folders, mark, copy and move items to folders.

See “Actions common to all applications” on page 30.

being copied, modified, transferred or forwarded.

Receiving files via Infrared

Go to Options→Receive via infrared.

Files are automatically received into the root level of the folder structureand can

be moved or copied to other folders. See “Infrared connection” on page 174.

Viewing memory consumption

Go to Options→Memory details.

If you have a memory card installed in your phone, you have a choice of two

memory views, one for the phone memory and one for the memory card.

Press

to move from one memory tab to another.

To check memory consumption of the current memory select Options→ Memory

details.

120

The phone calculates the approximate amount of free memory for storing data

and installing new applications.

In the memory views, you can view the memory consumption of the different data

groups: Calendar, Contacts, Documents, Messages, Images, Sound files, Video

clips, Applications, Mem. in use, and Free memory.

If the phone memory is getting low, remove some files, or move them to the

memory card. See “Troubleshooting” on page 181.

■ Voice commands

Go to Menu→Tools→Voice com..

You can use Voice commands to start applications and profiles, and to dial

numbers from Contacts, without having to look at your phone’s display. You

record a word, or words (voice command) and then pronounce this voice

command to open an application, activate a profile, or dial a number.

You can have only one voice command per item.

Options in the Voice commands main view are: Add voice command, Open,

New application, Playback, Change, Delete, Delete all, Help, and Exit.

Any spoken word(s) can be a voice command.

•

When recording, hold the phone at a short distance away from your mouth.

After the starting tone, clearly pronounce the word, or words, you want to

record as a voice command.

Before using voice tags, note that:

•

Voice tags are not language-dependent. They are dependent on the speaker's voice.

121

•

You must say the name exactly as you said it when you recorded it.

Voice tags are sensitive to background noise. Record voice tags and use them in a quiet

environment.

•

Very short names are not accepted. Use long names and avoid similar names for different

numbers.

Note: Using voice tags may be difficult in a noisy environment or during an

emergency, so you should not rely solely upon voice dialling in all circumstances.

Adding a voice command to an application

1. In the Voice commands main view, scroll to the application that you want to

add a voice command to, and select Options→Add voice command.

To add a voice command to a profile, the Profiles folder must be opened and a

specific profile selected.

To add an application to the list of applications in the Voice commands main

view, select Options→Newapplication, scroll to the application that you want

to add and press Select.

2. The text Press 'Start', then speak after tone is displayed.

•

Press Start to record a voice command. The phone sounds a starting tone

and the note Speak now is displayed.

3. Pronounce the voice command. The phone stops recording after approximately

5 seconds.

122

4. After recording, the phone plays the recorded command and the note Playing

voice command is displayed. If you do not want to save the recording, press

Quit.

5. When the voice command has been successfully saved, the note Voice

command saved is displayed and a beep sounds. A symbol can be seen next

to the application.

Starting an application using a voice command

1. In standby mode, press and hold

. A short tone is played and the note

Speak now is displayed.

2. When you are starting an application by saying a voice command, hold the

phone a short distance away from your mouth and pronounce the voice

command clearly.

3. The phone plays the original voice command and starts the application. If the

phone plays an incorrect voice command, press Retry.

Replaying, erasing, or changing a voice command

To replay, erase, or change a voice command, scroll to the item that has a voice

command (indicated by ), select Options, and then either:

•

Playback - Listen to the voice command again.

Delete - Erase the voice command.

Change - Record a new voice command. Press Start to record.

123

■ Device manager

Go to Menu→Tools→Device mgr..

Device manager allows a third party, such as your service provider, to assist you

directly with phone settings. To allow device management, your phone must

establish a connection and synchronise with the third party’s server. You can start

the synchonisation session from your phne, and you can accept or reject server-

initiated synchronisation attempts.

Options in the Device manager main view are: Start configuration, New

server profile, Edit profile, Delete, Enable config. / Disable config., View log, Help,

and Exit.

This feature is operator dependent and may not be available on all phones.

Contact your service provider for information and availability.

A device manager profile must be defined before you can connect to a server. The

third party who is assisting you can help define the profile settings:

•

Server name - Display name of the server.

Server ID - Remote device manager server ID.

Serverpassword - Password used in server alerts. Enter the password that must

be provided by the device manager server when synchronising with your

phone.

•

Access point - Internet access point your phone uses to establish the server

connection. Choose from the list of access points defined in your phone.

Host address - Device management server URL.

124

•

Port - Device management server port.

User name - Your user name for this profile.

Password - Your password for this profile.

Allow configuration - Device management allowed on this server. Select Yes or

No.

•

Auto-accept all reqs. - Automatic or approved device management on this

server. Select Yes to allow synchronisation without your verification, or select

No to verify each synchronisation attempt.

125

9. Personalising your phone

■ Profiles

Go to Menu→Profiles.

Options in the Profiles main view are: Activate, Personalise, Create new,

Delete profile, Help, and Exit.

In Profiles, you can adjust and customise the phone tones for different events,

environments, or caller groups. You can see the currently selected profile at the

top of the display in standby mode. If the General profile is in use, only the current

date is shown.

To change the profile, scroll to a profile and select Options→Activate.

To modify a profile, scroll to the profile in the Profiles list and select

Options→Personalise. To create a new profile, select Options→Create new. A list

of profile settings opens. Scroll to the setting you want to change and press

to open the choices:

•

Ringing tone - Set the ringing tone for voice calls, choose a ringing tone from

the list. Press any key to stop the sound. If a memory card is used, tones stored

on it have the

icon next to the tone name. Ringing tones use shared

memory. See “Shared memory” on page 16. You can also change ringing tones

in Contacts. See “Adding a ringing tone” on page 55.

•

Ringing type - When Ascending is selected, the ringing volume starts from

level one and increases level by level to the set volume level.

126

•

Ringing volume - Set the volume level for the ringing and message alert tones.

Message alert tone - Set the tone for messages.

Chat alert tone - Set the tone for instant messages.

Vibrating alert - Set the phone to vibrate at incoming voice calls and messages.

Keypad tones - Set the volume level for keypad tones.

Warning tones - The phone sounds a warning tone, for example, when the

battery is running low.

•

Alert for - Set the phone to ring only upon calls from phone numbers that

belong to a selected contact group. Phone calls coming from people outside

the selected group have a silent alert. The choices are All calls or (a list of

contact groups, if you have created them).

■ Themes

Go to Menu→Themes.

Options in the Themes main view are: Preview, Apply, Edit, Help, and Exit.

You can change the look of your phone’s display by activating a theme. A theme

can include the idle screen wallpaper, colour palette, screen saver, and

background image in ’Go to’. Edit a theme for more detailed personalisation.

When you open Themes you see a list of the available themes. The currently active

theme is indicated by a check mark. Press

card, if you use one.

to see the themes on the memory

127

To preview a theme, scroll to the theme and select Options→Preview to view the

theme. Press to activate the theme. You can activate the theme without

previewing it by selecting Options→Apply from the main view.

Group together elements from other themes, or images from the Gallery to

personalise themes further.

Editing a theme:

1. Scroll to a theme, select Options→Edit, and select:

•

Wallpaper - Select an image from one of the available themes, or select

your own image from the Gallery, to use as a background image in standby

mode.

•

Colour palette - Change the colour palette used on the display.

Screen saver - Select what is shown on the screen saver bar: the time and

date or a text that you have written yourself. The location and background

colour of the screen saver bar changes in 1-minute intervals. Also, the

screen saver changes to indicate the number of new messages or missed

calls. You can set the time that elapses before the screen saver is activated.

See “Phone settings” on page 130.

•

Image in 'Go to' - Select an image from one of the available themes, or

select your own image from the Gallery, to use as a background image in Go

to.

2. Scroll to the element to be edited and select Options→Change.

128

3. Select Options→Set to select the current setting. To preview the selected

element, select Options→ Preview. Note that you cannot preview all

elements.

To restore the currently selected theme to its original settings, select

Options→Restore orig. theme when editing a theme.

■ Settings

Changing general settings

Go to Menu→Settings

1. Scroll to a setting group and press

to open it.

2. Scroll to a setting you want to change and press

to:

switch between options if there are only two (On/Off),

open a list of options or an editor,

•

open a slider view and press

respectively.

to increase or decrease the value

You may be able to receive some settings from your service provider in a short

message. See “Receiving smart messages” on page 91.

129

Phone settings

Go to Phone.

General

•

Phone language - Change the language for the display texts in your phone.

This change may also affect the format used for date and time and the

separators used, for example, in calculations. If you select Automatic, the

phone selects the language according to the information on your SIM card.

After you have changed the display text language, you must restart the phone.

Changing the settings for Phone language or Writing language affects every

application in your phone and the change remains effective until you change

these settings again.

•

Writing language - Change the writing language of your phone. Changing the

language affects:

•

the characters available when you press any key

the predictive text dictionary used

the special characters that are available when you press the

keys.

and

•

Dictionary - Set predictive text input On or Off for all editors in the phone.

Select a language for entering predictive text from the list available. You can

also change this setting when you are in an editor. Press

and select

Dictionary→Dictionary on or Off.

Welcomenoteorlogo - The welcome note or logo is displayed briefly each time

you switch on the phone. Select Default if you want to use the default image

130

or animation. Select Text to write a welcome note (max. 50 letters). Select

Image to select a photo or picture from the Gallery.

•

Orig. phone settings - Reset some of the settings to their original values. To do

this, you need the lock code. See “Security” on page 139. After resetting the

settings, the phone may take a longer time to power up. All documents and

files that you have created are left as they are.

Standby mode

Left selection key and Right selection key - Change the shortcuts that appear

over the left and right selection keys in standby mode. In addition

•

to the applications, you can have the shortcut point to a function, for example,

New message.

You can only have shortcuts to pre-installed applications and functions.

Display

•

Brightness - Adjust the brightness of the display.

•

Screen saver timeout - The screen saver is activated when the screen saver

time-out period is over. When the screen saver is active, the display is cleared

and you can see the screen saver bar.

•

To deactivate the screen saver press any key.

131

Call settings

Go to Call.

Send my caller ID (network service)

•

Set your phone number to be displayed (Yes) or hidden (No) from the person

whom you are calling. Or, the value may be set by your network operator or

service provider when you make a subscription.

Call waiting (network service)

•

The network notifies you of a new incoming call while you have a call in

progress. Select Activate to request the network to activate call waiting,

Cancel to request the network to deactivate call waiting, or Check status to

check if the function is active or not.

Automatic redial

When this setting is activated, your phone makes a maximum of ten attempts

•

to connect the call after an unsuccessful call attempt. Press

automatic redialling.

to stop

Summary after call

•

Activate this setting if you want the phone to briefly display the approximate

duration of the last call.

Speed dialling

Select On, and the numbers assigned to the speed-dialling keys (

) can be dialled by pressing and holding the key. See “Assigning speed-

dialling keys” on page 57.

•

132

Anykey answer

Select On, and you can answer an incoming call by briefly pressing any key,

except , and

•

Ans. by opening fold

•

Select Yes, and the phone automatically answers an incoming callbwhen the

fold is opened.

Line in use (network service)

•

This setting is shown only if the SIM card supports two subscriber numbers,

that is, two phone lines. Select which phone line (Line 1 or Line 2) you want to

use for making calls and sending short messages. Calls on both lines can be

answered irrespective of the selected line.

Note: You cannot make calls if you select Line 2 and have not subscribed

to this network service.

To prevent line selection, select Line change→Disable if supported by your SIM

card. To change this setting, you need the PIN2 code.

Connection settings

Go to Connection settings.

Access points

Here you can see a short explanation for every setting that may be needed for

different data connections and access points. If you have not yet used your phone

to make a WAP connection, you may need to contact your service provider for

assistance with the first-time connection.

133

Many service providers require you to use an IAP for your default access point.

Other service providers allow you to use a WAP access point. Contact your service

provider for more information.

Start to fill in the settings from the top since, depending on the data connection

you select (Data bearer), only certain fields are available.

•

Connection name - Give a descriptive name for the connection.

Data bearer - The options are GPRS or Data call. Depending on what data

connection you select, only certain setting fields are available. Fill in all fields

marked with Must be defined, or with an asterisk. Other fields can be left

empty, unless you have been instructed otherwise by your service provider.

To be able to use a data connection, the network operator or service provider must

support this feature, and if necessary, activate it for your SIM card

•

Access point name (for packet data only) - The access point name is needed to

establish a connection to the GPRS network. You obtain the access point name

from your network operator or service provider.

•

Dial-up number (for data call only) - The modem telephone number of the

access point.

User name - Write a user name if required by the service provider. The user

name may be needed to make a data connection, and is usually provided by the

service provider. The user name is often case-sensitive.

•

Prompt password - If you must key in a new password every time you log onto

a server, or if you do not want to save your password to the phone, choose Yes.

134

•

Password - A password may be needed to make a data connection, and is

usually provided by the service provider. The password is often case-sensitive.

When you are writing the password, the characters you enter are shown briefly

and then changed to asterisks (*). The easiest way to enter numbers is to press

and hold the digit you want to enter, and then continue entering letters.

•

Authentication - Normal/Secure.

Homepage - Depending on what you are setting up, enter either:

•

the service address, or

the address of the multimedia messaging centre.

•

Data call type (for data call only) - Analogue, ISDN v.110, or ISDN v.120 defines

whether the phone uses an analogue or digital connection. This setting

depends on both your GSM network operator and Internet Service Provider

(ISP), because some GSM networks do not support certain types of ISDN

connections. For details, contact your ISP. If ISDN connections are available,

they establish connections more quickly than analogue methods.

Maximum data speed (for data call only) - The options are Automatic, 9600,

14400, 19200, 28800, 38400or 43200, depending on the chosen Data call

type. This option allows you to limit the maximum connection speed when

GSM data are used. Higher data rates may cost more, depending on the service

provider.

The speeds above represent the maximum speed at which your connection

operates. During the connection, the operating speed may be less, depending on

network conditions.

135

Options→ Advanced settings

•

Network type – The internet protocol (IP) version of the network.

Phone IP address - The IP address of your phone.

Name servers - The IP address of the primary and secondary DNS servers.

Proxy serv. address - The IP address of the proxy server.

Proxy port number - The port number of the proxy server.

To enter these settings, contact your Internet service provider.

The following settings are shown if you have selected data call as the connection

type:

•

Use callback - This option allows a server to call you back once you have made

the initial call. Contact your service provider to subscribe to this service.

The phone expects the callback call to use the same data call settings that

were used in the callback-requesting call. The network must support that type

of call in both directions, to and from the phone.

•

Callback type - The options are Use server no./Use other no.. Ask your service

provider for the correct setting to use.

Callbacknumber - Key in your phone’s data phone number which the dial-back

server uses. Usually, this number is the data-call phone number of your phone.

Use PPP compression - When set to Yes, this option speeds up data transfer, if

supported by the remote PPP server. If you have problems with establishing a

connection, try setting this to No. Contact your service provider for guidance.

•

Use login script - The options are Yes/No.

136

•

Modem initialisation (Modem initialisation string) - Controls your phone using

modem AT commands. If required, enter characters specified by your service

provider or Internet service provider.

GPRS

Go to GPRS.

The GPRS settings affect all access points using a packet data connection.

GPRS connection - If you select When available and you are in a network that

supports packet data, the phone registers to the GPRS network and short

messages are sent via GPRS. Also, starting an active packet data connection, for

example, to send and receive e-mail, is quicker. If you select When needed, the

phone uses a packet data connection only if you start an application or action that

needs it. The GPRS connection can be closed when it is not needed by any

application.

If there is no GPRS coverage and you have chosen When available, the phone

periodically tries to establish a packet data connection.

Access point - The access point name is needed when you want to use your phone

as a packet data modem to your computer.

137

Data call

Go to Data call.

The Data call settings affect all access points that use a GSM data call.

Online time - If there are no actions the data call is dropped automatically after a

time-out period. The options are User defined, in which case you enter a time, or

Unlimited.

Date and time

Go to Date and time.

The Date and time settings allow you to define the date and time used in your

phone, as well as change the date and time format and separators.

•

Clocktype→Analogue or Digital - To change the clock shown in standby mode.

See “Clock” on page 154.

Auto time update - To allow the network to update time, date, and time zone

information to your phone (network service). For the Auto time update setting

to take effect, the phone needs to be restarted. Check any alarms as these may

be affected by Auto time update.

•

Clock alarm tone - To change the tone played when the clock alarm time is

reached.

•

GMT offset - To change the time zone for the clock time.

Daylight-saving - To turn daylight saving time on or off.

138

Security

Go to Security.

Phone and SIM

You can change the following codes: lock code, PIN code, and PIN2 code. These

codes can only include the numbers from 0 to 9.

Avoid using access codes similar to emergency numbers, such as 112, to prevent

accidental dialling of the emergency number.

PINcoderequest - When the PIN code request is active, the code is requested each

time the phone is switched on. Note that some SIM cards may not allow the PIN

code request to be deactivated.

PIN code/PIN2 code/Lock code - Open this setting if you want to change the code.

Autolock period - You can set an autolock period, a time-out after which the

phone is automatically locked and can be used only if the correct lock code is

entered. Key in a number for the time-out in minutes or select None to turn off

the autolock period.

•

To unlock the phone, key in the lock code.

LockifSIM changed - Select Yes if you want the phone to prompt for the lock code

when an unknown, new SIM card is inserted into your phone. The phone maintains

a list of SIM cards that are recognised as the owner’s cards.

Options in the Fixed dialling view are: Open, Call, Activ. fixed dialling,

Deact. fixed dialling, New contact, Edit, Delete, Add to Contacts, Add from

Contacts, Find, Mark/Unmark, Help, and Exit.

139

Fixed dialling - You can restrict your outgoing calls to selected phone numbers, if

supported by your SIM card. You need the PIN2 code for this function. When this

function is active, you can only call those phone numbers that are included in the

fixed-dialling list or which begin with the same digit(s) as a phone number on the

list.

•

Press

to set Fixed dialling on.

To add new numbers to the Fixed dialling list, select Options→New contact or

Add from Contacts.

Closed user group (network service) - You can specify a group of people whom you

can call and who can call you. For more information, contact your network

operator or service provider. Select: Default to activate the default group agreed

on with the network operator, On if you want to use another group (you need to

know the group index number), or Off.

When security features that restrict calls are in use (such as call barring, closed user group

and fixed dialing) calls still may be possible to the official emergency number programmed

into your device.

Confirm SIM services (network service) - To set the phone to display confirmation

messages when you are using a SIM card service.

Certificate management

Options in the certificate management main view are: Certificate details,

Delete, Trust settings, Mark/Unmark, Help, and Exit.

140

In the certificate management main view, you can see a list of authority

certificates that have been stored in your phone. Press

certificates, if available.

to see a list of personal

Authority certificates are used by some browser services, such as banking services,

for checking signatures or server certificates or other authority certificates.

Server certificates are used to improve security in the connection between the

phone and the gateway. The phone receives the server certificate from the service

provider before the connection is established and its validity is checked using the

authority certificates saved in the phone. Server certificates are not saved.

Server certificates may be needed when you, for example:

•

want to connect to an online bank or another site or remote server for actions

that involve transferring confidential information, or

•

want to be sure of the authenticity of software when downloading and

installing software.

Important: Note that even if the use of certificates considerably reduces the risks

involved in remote connections and software installation, they must be used

correctly in order to benefit from increased security. The existence of a certificate

does not offer any protection by itself; the certificate manager must contain

correct, authentic, or trusted certificates for increased security to be available.

Certificates have a restricted lifetime. If Expired certificate or Certificate not valid

yet is shown even if the certificate should be valid, check that the current date and

time in your device are correct.

Before changing any certificate settings, you must make sure that you actually

trust the owner of the certificate and that the certificate really belongs to the

listed owner.

141

Changing the trust settings of an authority certificate

•

Scroll to an authority certificate and select Options→ Trust settings.

Depending on the certificate, a list of the applications that can use the

selected certificate is shown. For example:

Application manager/Yes - The certificate is able to certify the origin of new

software.

Internet/Yes - The certificate is able to certify e-mail and imaging servers.

Call barring

Go to Call barring.

Call barring (network service) allows you to restrict the making and receiving of

calls with your phone. For this function, you need the barring password obtainable

from your service provider.

1. Scroll to one of the barring options.

2. Select Options→Activate to request the network to set call restriction on,

Cancel to set the selected call restriction off, or Check status to check if the

calls are barred or not.

•

Select Options→Edit barrings passw. to change the barring password.

Select Options→Cancel all barrings to cancel all active call barrings.

Call barring and call diverting cannot be active at the same time.

When calls are barred, calls still may be possible to certain official emergency numbers.

142

Network

Go to Network.

Operator selection

•

Automatic - Set the phone to automatically search for and select one of the

cellular networks available in your area.

Manual - Select the desired network manually from a list of networks. If the

connection to the manually selected network is lost, the phone sounds an error

tone and asks you to select a network again. The selected network must have a

roaming agreement with your home network, that is, the operator whose SIM

card is in your phone.

Cell info display

•

On - Set the phone to indicate when it is used in a cellular network based on

Micro Cellular Network (MCN) technology and to activate cell info reception

(network service).

Enhancement settings

Go to Enhancement.

Scroll to an enhancement folder and open the settings:

•

Default profile - Select the profile you want to activate each time you connect

a certain enhancement to your phone.

143

•

Automatic answer - Set the phone to answer an incoming call automatically

after 5 seconds after you connect this enhancement to your phone. If the

Ringing type is set to Beep once or Silent, automatic answer cannot be used,

and you must answer the phone manually.

■ Go to

Go to Menu→Go to or press Go to in standby mode.

Options in the Go to main view are: Open, Edit shortcut name, Shortcut

icon, Delete shortcut, Move, List view/Grid view, Help, and Exit.

Use Go to for storing shortcuts, links to your favourite photos, video clips, notes,

Recorder sound files, and browser bookmarks.

The default shortcuts are:

at the current date, and

- opens the Notes editor,

- opens the Messaging Inbox.

- opens the Calendar

Shortcuts can be added only from some of the functions. Applications do not have

this functionality.

Adding and using shortcuts:

1. Open the application and scroll to the item that you want to add as a shortcut.

2. Select Options→Add to 'Go to' and press OK.

•

To open a shortcut, scroll to the icon and press

. The file is opened in the

corresponding application.

144

•

To delete a shortcut, scroll to the shortcut that you want to remove and select

Options→Delete shortcut. Removing a shortcut does not affect the file it is

referring to.

To change the shortcut name, select Options→Edit shortcut name. Write the

new name. This change affects only the shortcut, not the file or the item that

the shortcut refers to.

145

10. Extras

■ Wallet

Go to Menu→Extras→Wallet.

Options in the wallet main view are: Open, Settings, Help, and Exit.

Wallet provides you with a storage area for your personal information, such as

credit and debit card numbers, addresses and other useful data, for example, user

names and passwords.

The information stored in the wallet can be easily retrieved while browsing to

automatically complete online forms on browser pages, for example, when the

service asks for credit card details. Data in the wallet are encrypted and protected

with a wallet code that you define.

You can group wallet data into profiles that can be accessed, for example, when

making purchases online.

Due to the nature of the wallet, it automatically closes after 5 minutes. Enter the

wallet code to regain access to the contents. You can change this automatic time-

out period, if required. See “Presence settings” on page 63.

Entering the wallet code

Each time you open the wallet you are prompted for a wallet code.

When you open the wallet for the first time, you must create your own access

code:

146

1. Enter a code of your choice (4 - 10 alphanumeric characters), and press OK.

2. You are prompted to verify the code. Enter the same code and press OK. Do not

give your wallet code to anyone else.

3. Enter the code that you have created and press OK.

If you enter the wallet code incorrectly on three consecutive occasions, the wallet

application is blocked for 5 minutes. The block time increases if further incorrect

wallet codes are entered.

If you forget your wallet code, you have to reset the code, and you will lose all

information stored in the wallet. See “Resetting the wallet and wallet code” on

page 151.

Storing personal card details

1. Select the Cards category from the main wallet menu and press

2. Select a type of card from the list and press

•

Payment cards - Credit and debit cards.

Loyalty cards - Membership and store cards.

Online acc. cards - Personal user names and passwords to online services.

Address cards - Basic contact details for home/office.

User info cards - Customised personal preferences for online services.

3. Select Options→New card. A blank form opens.

4. Fill in the fields and press Done.

147

You can also receive card information directly to the phone from a card issuer or

service provider (if they offer this service). You are notified which category the

card belongs to. Either save or discard the card. You can view and rename a saved

card, but you cannot edit it.

You can open, edit or delete the fields in the card. Any changes are saved upon

exiting.

Options when viewing or editing card details: Delete, Help, and Exit.

Creating personal notes

Personal notes are a means of storing sensitive information, for example, a bank

account number. You can access the data in a personal note from the browser.

You can also send a note as a message.

•

Select the Personal notes category from the main wallet menu and press

Select Options→New card. A blank note opens.

Press

to start writing. Press

to clear characters. Press

Done to save.

Creating a wallet profile

Once you have stored your personal details, you can combine them together into a

wallet profile. Use a wallet profile to retrieve wallet data from different cards and

categories to the browser.

1. Select the Wallet profiles category from the main wallet menu and press

2. Select Options→New card. A new wallet profile form opens.

148

3. Fill in the fields as indicated below and press Done.

Some of the fields must contain data selected from the wallet. Save the data

under the relevant category before creating a wallet profile, or the profile

cannot be created.

•

Profile name - Choose and enter a name for the profile.

Payment card - Select a card from the Payment card category.

Loyalty card - Select a card from the Loyalty card category.

Online access card - Select a card from the Online access card category.

Shipping address - Select an address from the Address card category.

Billing address - By default this is the same as the Shipping address. If you

require a different address, select one from the Address card category.

•

User info card - Select a card from the User info card category.

Receive e-receipt - Select a destination from the Address card category.

Deliver e-receipt - Select To phone, To e-mail, or To pho. & e-mail.

RFID sending - Set to On or Off. Defines whether or not your unique phone

identification is sent with the wallet profile (for future development

dependent on RFID-based ticketing).

Retrieving information from the wallet to your browser

When using online mobile services supporting the wallet functionality, you can

upload the data stored in your wallet to automatically enter your details into an

online form. For example, by uploading your payment card details you do not need

149

to key in the card number and expiry date each time you need them (depending on

the content being browsed). Also, you can retrieve your user name and password

stored as an access card when connecting to a mobile service that requires

authentication. See “Purchasing an item” on page 166.

A cache is a memory location that is used to store data temporarily. If you have tried to

access or have accessed confidential information requiring passwords, empty the cache

after each use. The information or services you have accessed is stored in the cache. To

empty the cache, select Menu→Web→Options→Navigation options→Clear Cache.

Viewing ticket details

Options in the Tickets main view are: View, Delete, Rename, Mark/Unmark,

Help, and Exit.

You can receive notifications of tickets purchased online via the browser.

Received notifications are stored in the wallet. To view the notifications:

1. Select the Tickets category from the main wallet menu and press

2. Select Options→View.

Wallet settings

Select Options→Settings from the main wallet menu:

•

Wallet code - Change your wallet code. You are prompted to enter the current

code, create a new code, and verify the new code.

150

•

RFID - Set the phone ID code, type, and sending options (for future

development dependent on RFID-based ticketing).

Automatic close - Change the automatic time-out period (1 - 60 minutes).

After the time-out period has elapsed, the wallet code must be re-entered to

gain access to the contents.

Resetting the wallet and wallet code

To reset both the contents of the wallet and the wallet code:

1. Key in *#7370925538# in standby mode.

2. Enter the phone’s lock code, and press OK. See “Security” on page 139.

3. You are asked to confirm the erasing of data. Press OK.

When opening the wallet again, you must enter a new wallet code. See “Entering

the wallet code” on page 146.

■ Calculator

Go to Menu→Extras→Calculator.

1. Enter the first number of your calculation. If you make a mistake, press

to erase it.

2. Scroll to an arithmetic function and press

to select it.

3. Enter the second number.

4. To execute the calculation, scroll to

and press .

Options in Calculator are: Last result, Memory, Clear screen, Help, and Exit.

151

Note: This calculator has limited accuracy and is designed for simple calculations.

•

To add a decimal, press

Press and hold

Use and

to clear the result of the previous calculation.

to view previous calculations and move in the sheet.

■ Converter

Go to Menu→Extras→Converter.

In Converter, you can convert measurement parameters such as Length from one

unit to another, for example, Yards to Metres.

The Converter has limited accuracy and rounding errors may occur.

Converting units

Options in Converter: Conversion type, Currency rates (not applicable to

other units), Help, and Exit.

To make currency conversion you must first set the exchange rate. See “Setting a

base currency and exchange rates” on page 153.

1. Scroll to the Type field and press

to open a list of measurement

parameters. Scroll to the measurement parameter you want to use and press

OK.

2. Scroll to the first Unit field and press

to open a list of available units.

Select the unit from which you want to convert and press OK.

152

3. Scroll to the next Unit field and select the unit to which you want to convert.

4. Scroll to the first Amount field and key in the value that you want to convert.

The other Amount field changes automatically to show the converted value.

Press

to add a decimal and press

for the +, - (for temperature),

and E (exponent) symbols.

The conversion order changes if you write a value in the second Amount field. The

result is shown in the first Amount field.

Setting a base currency and exchange rates

Before you can carry out currency conversions, you need to choose a base

currency (usually your domestic currency) and add exchange rates.

The rate of the base currency is always 1. The base currency determines the

conversion rates of the other currencies.

1. Select Currency as the measurement parameter type and select

Options→Currency rates. A list of currencies opens and you can see the

current base currency at the top.

2. To change the base currency, scroll to the currency (usually your domestic

currency), and select Options→Set as base curr..

3. Add exchange rates, scroll to the currency, and key in a new rate, that is, how

many units of the currency equal one unit of the base currency you have

selected.

4. After you have inserted all the required exchange rates, you can make currency

conversions. See “Converting units” on page 152.

153

■ Notes

Go to Menu→Extras→Notes.

You can link notes to Go to and send them to other devices. Plain text files (TXT

format) you receive can be saved to Notes.

•

Press

to start to write. Press

to clear letters. Press Done

to save.

■ Clock

Go to Menu→Extras→Clock.

Changing clock settings

Options in Clock: Set alarm, Reset alarm, Removealarm, Settings, Help, and

Exit.

•

To change the time or date, select Options→Settings in Clock.

Setting an alarm

1. To set a new alarm, select Options→Set alarm.

2. Enter the alarm time and press OK. When the alarm is active, the

indicator

is shown.

•

To cancel an alarm, go to Clock and select Options→Remove alarm.

154

Turning off the alarm

•

Press Stop to turn off the alarm.

•

Press Snooze to stop the alarm for5 minutes, after which it resumes. You can

do this a maximum of five times.

If the alarm time is reached while the device is switched off, the device switches itself on

and starts sounding the alarm tone. If you press Stop, the device asks whether you want to

activate the device for calls. Press No to switch off the device or Yes to make and receive

calls. Do not press Yes when wireless phone use may cause interference or danger.

Personalising the alarm tone

1. To personalise the alarm tone, select Options→Settings.

2. Scroll to Clock alarm tone and press

3. When you scroll through the list of tones, you can stop on a tone to listen to it

before you make your selection. Press Select to select the current tone.

■ Recorder

Go to Menu→Extras→Recorder.

The voice recorder allows you to record telephone conversations and

voice memos. If you are recording a telephone conversation, both parties hear a

tone every 5 seconds during recording.

Recorded files are stored in the Gallery. See “Gallery” on page 81.

Options in Recorder are: Record sound clip, Delete, Rename sound clip,

Send, Go to Gallery, Settings, Add to 'Go to', Help, and Exit.

155

•

Select Options→Record sound clip and scroll to a function and press

select it. Use:

forward,

- to record,

- to pause,

- to stop,

- to fast

- to rewind, or

- to play an opened sound file.

The recorder cannot be used when a data call or GPRS connection is active.

■ Memory card

Go to Menu→Extras→Memory card.

Options in the memory card: Backup phone mem., Restore from card,

Format mem. card, Memory card name, Set password, Change password, Remove

password, Unlock memory card, Memory details, Help, and Exit.

For details on inserting a memory card into the phone, see the Getting Started

section. You can use it to store your multimedia files such as video clips and sound

files, photos, and messaging data, and to back up information from your phone’s

memory.

Included with your Nokia phone is a Reduced Size MultiMedia Card (RS-MMC)

that may contain add-on applications from independent developers. These

applications are designed by the developers to be compatible with your phone.

Use only compatible MultiMediaCard (MMC) with this device. The compatible MMC for your

phone is Reduced Size Dual Voltage MultiMediaCard. Other memory cards, such as Secure

Digital (SD) cards, do not fit in the MMC card slot and are not compatible with this device.

Using an incompatible memory card may damage the memory card as well as the device, and

data stored on the incompatible card may be corrupted.

156

Details of how you can use the memory card with other features and applications

of your phone are given in the sections describing these features and applications.

Keep all memory cards out of the reach of small children.

Formatting the memory card

When a memory card is formatted, all data on the card are permanently lost.

Some memory cards are supplied pre-formatted and others require formatting.

Consult your retailer to find out if you must format the memory card before you

can use it.

•

Select Options→ Format mem. card.

Select Yes to confirm. When formatting is complete, key in a name for the

memory card (max. 11 letters or numbers).

Backing up and restoring information

To back up information from your phone’s memory to the memory card, select

Options→ Backup phone mem.

To restore information from the memory card to the phone’s memory, select

Options→ Restore from card.

You can only back up the phone memory and restore it to the same phone.

157

Locking the memory card

To set a password to lock your memory card to help prevent unauthorised use,

select Options→ Set password.

You are asked to enter and confirm your password. The password can be up to

eight characters long.

The password is stored in your phone and you do not have to enter it again while

you are using the memory card on the same phone. If you want to use the memory

card on another phone, you are asked for the password.

Unlocking a memory card

If you insert another password-protected memory card into your phone, you are

prompted to enter the password of the card. To unlock the card:

•

Select Options→ Unlock memory card.

Once the password is removed, the memory card is unlocked and can be used on

another phone without a password.

Checking memory consumption

You can check the memory consumption of different data groups and the

available memory for installing new applications or software on your memory

card:

•

Select Options→Memory details.

158

■ Quickword

Go to Menu→Extras→Quickword.

Quickword allows you to open and view MS Word documents on your phone.

Note: Quickword is designed to support documents saved in Microsoft Word 97,

2000, and XP document format (.doc). Note that this application does not

necessarily support all variations or features of the mentioned file formats.

■ Quickpoint

Go to Menu→Extras→Quickpoint.

Quickpoint allows you to:

•

view presentations and move between the Outline, Slide, Thumb, and Notes

views.

Note: Quickpoint is designed to support presentations created in Microsoft

Powerpoint 97, 2000, and XP file formats (.ppt). Note that this application does not

necessarily support all variations or features of the mentioned file formats.

159

11. Services and Applications

■ Web (Mobile browser)

Go to Menu→Web or press and hold

in standby mode.

Various service providers maintain pages specifically designed for mobile

phones, offering services that can be, for example, news, weather reports,

banking, travel information, entertainment, and games. With the mobile browser,

you can view these services as WAP pages written in HTML, WML, and XHTML

pages written in XHTML, or a mixture of WML and XHTML. If you have not yet used

your phone to make a WAP connection, you may need to contact your service

provider for assistance with the first-time connection.

Check the availability of services, pricing, and tariffs with your network operator

and/or service provider. Service providers also give you instructions on how to use

their services.

Basic steps for accessing

•

Save the settings that are needed to access the browser service that you want

to use. See “Setting up the phone for the browser service” on page 161.

•

Make a connection to the service. See “Making a connection” on page 161.

Start browsing the web pages. See “Browsing” on page 163.

End the connection to the service. See “Ending a connection” on page 167.

160

Setting up the phone for the browser service

Receiving settings in a smart message

You may receive service settings in a special text message, a so-called smart

message, from the network operator or service provider that offers the service. See

“Receiving smart messages” on page 91. For more information, contact your

network operator or service provider.

Keying in the settings manually

Follow the instructions given to you by your service provider.

1. Go to Menu→Settings→Connection→Access points and define the settings

for an access point. See “Connection settings” on page 133.

2. Go to Menu→Web→Options→Bookmark manager→Add bookmark. Write a

name for the bookmark and the address of the browser page defined for the

current access point.

Making a connection

Once you have stored all the required connection settings, you can access browser

pages.

There are three different ways to access browser pages:

•

Select the homepage ( ) of your service provider.

Select a bookmark from the Bookmarks view.

161

•

Press the keys

to start to write the address of a browser service.

The Go to field at the bottom of the display is immediately activated and you

can continue writing the address there.

After you have selected a page or written the address, press

download the page.

to start to

Viewing bookmarks

Your device may have some bookmarks loaded for sites not affiliated with Nokia. Nokia does

not guarantee or endorse these sites. If you choose to access them, you should take the same

precautions, for security or content, as you would with any Internet site.

Options in the Bookmarks view (when a bookmark or folder is selected):

Open, Download, Back to page, Bookmark manager, Mark/Unmark, Navigation

options, Advanced options, Send, Find bookmark, Details, Settings, Help, and Exit.

In the Bookmarks view, you can see bookmarks pointing to different kinds of

browser pages. Bookmarks are indicated by the following icons:

- The starting page defined for the browser access point. If you use another

browser access point for browsing, the starting page is changed accordingly.

- The last visited page. When the phone is disconnected from the service, the

address of the last visited page is kept in memory until a new page is visited

during the next connection.

When you scroll through bookmarks, you can see the address of the highlighted

bookmark in the Go to field at the bottom of the display.

- A bookmark showing the title.

162

Adding bookmarks manually

1. In the Bookmarks view, select Options→Bookmark manager→ Add bookmark.

2. Start to fill in the fields. Only the address must be defined. The default access

point is assigned to the bookmark if no other one is selected. Press

enter special characters such as /, ., :, and @. Press

to clear characters.

3. Select Options→Save to save the bookmark.

Browsing

On a browser page, new links appear underlined in blue and previously visited links

in purple. Images that act as links have a blue border around them.

Options when browsing: Open, Service options, Bookmarks, Save as

bookmark, View image, Navigation options, Advanced options, Send bookmark,

Find, Details, Settings, Help, and Exit.

Keys and commands used in browsing

•

To open a link, press

To scroll the view, use the scroll key.

To enter letters and numbers in a field, press the keys

. Press

to enter special characters such as /, ., :, and @. Press

characters.

to clear

•

To go to the previous page while browsing, press Back. If Back is not available,

select Options→Navigation options→History to view a chronological list of

the pages you have visited during a browsing session. The history list is cleared

each time a session is closed.

163

•

To check boxes and make selections, press

To retrieve the latest content from the server, select Options→Navigation

options→Reload.

•

To open a sub-list of commands or actions for the currently open browser

page, select Options→Service options.

To disconnect from a browser service and to quit browsing, press and hold

Saving bookmarks

•

To save a bookmark while browsing, select Options→Save as bookmark.

•

To save a bookmark received in a smart message, open the message in the

Inbox in Messaging and select Options→Save to bookmarks. See “Receiving

smart messages” on page 91.

Viewing saved pages

Options in the Saved pages view are: Open, Back to page, Reload, Saved

pages, Mark/Unmark, Navigation options, Advanced options, Details, Settings,

Help, and Exit.

If you regularly browse pages containing information which doesn’t change very

often, you can save and then browse them when offline.

•

To save a page, while browsing select Options→Advanced options→Save

page.

Saved pages are indicated by the following icon:

- The saved browser page.

164

In the saved pages view you can also create folders to store your saved browser

pages.

Folders are indicated by the following icon:

- Folder containing saved browser pages.

•

To open the Saved pages view, press

in the Bookmarks view. In the Saved

pages view, press to open a saved page.

To start a connection to the browser service and to retrieve the page again, select

Options→Navigation options→Reload.

The phone stays online after you reload the page.

A cache is a memory location that is used to store data temporarily. If you have tried to

access or have accessed confidential information requiring passwords, empty the cache

after each use. The information or services you have accessed is stored in the cache. To

empty the cache, select Menu→ Web→Options→

Navigation options→Clear Cache.

Downloading

You can download items such as ringing tones, images, operator logos, software,

and video clips using the mobile browser. These items can be provided free or you

can purchase them.

Once downloaded, items are handled by the respective applications on your

phone, for example, a downloaded photo is saved in the Gallery.

Important: Only install and use applications and other software from sources that

offer adequate security and protection against harmful software.

165

Purchasing an item

To download the item:

1. Scroll to the link and select Options→Open.

2. Choose the appropriate option to purchase the item, for example, Buy.

Carefully read all the information provided.

If the online content is compatible, you can use your wallet information to make

the purchase:

1. Select Open wallet. You are prompted for your wallet code. See “Entering the

wallet code” on page 146.

2. Select the appropriate card category from your wallet.

3. Select Fill in. This uploads the selected wallet information.

If the wallet does not contain all information necessary for the purchase, you are

requested to enter the remaining details manually.

copied, modified, transferred or forwarded.

Checking an item before downloading

You can see details about an item before you download it. Details about an item

may include the price, a brief description and size.

•

Scroll to the link and select Options→Open.

Details about the item are displayed on your phone.

If you want to continue with the downloading, press Accept, or if you want to

cancel the download, press Cancel.

166

Ending a connection

•

Select Options→Advanced options→Disconnect, or

Press and hold to quit browsing and to return to standby mode.

•

Browser settings

Select Options→Settings:

•

Default access point - To change the default access point, press

list of available access points. The current default access point is highlighted.

See “Connection settings” on page 133.

to open a

Show images - Choose whether to view pictures when you are browsing. If you

choose No, you can later load images during browsing by selecting

Options→Show images.

Text wrapping - Choose Off if you do not want the text in a paragraph to

automatically wrap, or On if you do. If text is not wrapped, the ends of lines

may be truncated.

•

Font size - You can choose five text sizes in the browser: Smallest, Small,

Normal, Large, and Largest.

Default encoding - To make sure your browser pages display text characters

correctly, select the appropriate language type.

Automatic bookmarks - Choose On if you want the bookmarks to be

automatically saved in the Auto. bookmarks folder when you visit a page.

When you select Hide folder, the bookmarks are still automatically added to

the folder.

167

•

Screen size - Choose how to use the display area for viewing pages.

Rendering - Choose the image quality for the pages. With the high image

quality, the page download speed is slower, and vice versa.

•

Cookies - Allow/Reject. You can enable or disable the receiving and sending of

cookies (a means for content providers to identify users and their preferences

for frequently used content).

•

Security warnings - Choose to hide or show security notifications.

Conf. DTMF sending - Always/First time only. Choose whether you want to

confirm before the phone sends DTMF tones during a voice call. See “Options

during a call” on page 37. For example, you can make a voice call while you are

viewing a browser page, send DTMF tones while a voice call is in progress, and

save a name and phone number from a browser page into Contacts.

•

Wallet - Choose On to open the wallet automatically when a compatible

browser page is opened.

■ Games

Go to Menu→Games.

To start a game, scroll to the game icon and press

. For instructions on how to

play the game, select Options→Help.

168

12. Connectivity

■ Bluetooth connection

Go to Menu→Connectivity→Bluetooth.

This device is compliant with Bluetooth wireless technology

Specification 1.1 supporting the following profiles: Hands-free,

Object Push Profile, File Transfer Profile, Dial Up Networking

Profile and Fax Profile. To ensure interoperability between

other devices supporting Bluetooth wireless technology, use

Nokia approved enhancements for this model. Check with the

manufacturers of other devices to determine their

compatibility with this device.

There may be restrictions on using Bluetooth technology in

some locations. Check with your local authorities or service

provider.

Features using Bluetooth wireless technology, or allowing such

features to run in the background while using other features,

increase the demand on battery power and reduces the battery life.

Bluetooth technology enables wireless connections between electronic devices

within a maximum range of 10 metres. A Bluetooth connection can be used to

send images, videos, texts, business cards, calendar notes, or to connect wirelessly

to compatible devices using Bluetooth technology, such as computers. Please note

that not all computers using Bluetooth technology are necessarily compatible.

169

Since devices using Bluetooth technology communicate using radio waves, your

phone and the other devices do not need to be in direct line-of-sight. The two

devices only need to be within a maximum of 10 metres of each other, although

the connection can be subject to interference from obstructions such as walls or

from other electronic devices. Using Bluetooth technology consumes the battery

and the phone's operating time is reduced. Take this into account when

performing other operations with your phone. There may be restrictions on using

devices using Bluetooth technology. Check with your local authorities.

When you activate Bluetooth technology for the first time, you are asked to give a

name to your phone.

Bluetooth connection settings

•

Bluetooth - On/Off.

•

My phone's visibility - Shown to all - Your phone can be found by other

Bluetooth devices or Hidden - Your phone cannot be found by other devices.

For security reasons it is advisable to use the hidden mode whenever possible.

•

My phone's name - Define a name for your phone.

After you have set the Bluetooth connection as active and changed My phone's

visibility to Shown to all, your phone and this name can be seen by other

Bluetooth device users.

Sending data via Bluetooth technology

There can be only one active Bluetooth connection at a time.

170

1. Open an application where the item you wish to send is stored. For example, to

send a photo to another device, open the Gallery application.

2. Scroll to the item you want to send and select Options→Send→Via Bluetooth.

3. The phone starts to search for devices within range. Devices using Bluetooth

technology that are within range start to appear on the display one by one. You

can see a device icon, the device’s name, the device type, or a short name.

Paired devices are shown with . A paired device is one where a Bluetooth

connection already exists between your phone and the other device.

•

To interrupt the search, press Stop. The device list freezes and you can start

to form a connection to one of the devices already found.

4. When searching for devices, some devices may show only the unique device

addresses. To find out the unique address of your phone, enter the code

*#2820# in standby mode when the Bluetooth connection is active.

If you have searched for devices earlier, a list of the devices that were found

previously is shown first. To start a new search, select More devices. If you

switch off the phone, the list of devices is cleared and the device search needs

to be started again before sending data.

5. Scroll to the device you want to connect with and press Select. The item you

are sending is copied to Outbox and the note Connecting is shown.

6. Pairing (if not required by the other device, go to step 7.)

•

If the other device requires pairing before data can be transmitted, a tone

sounds and you are asked to enter a passcode.

171

•

Create your own passcode (1-16 characters long, numeric) and agree with

the owner of the other device to use the same code. This passcode is used

only once and you do not have to memorise it.

After pairing, the device is saved to the Paired devices view.

7. When the connection has been successfully established, the note Sending data

is shown.

Data received via Bluetooth connection can be found in the Inbox folder in

Messaging. See "Inbox - receiving messages".

Icons for different devices: - Computer, - Phone, - Audio/video, and

- Bluetooth device.

If sending fails, the message or data are deleted. The Drafts folder in Messaging

does not store messages sent via Bluetooth connection.

Checking the status of the Bluetooth connection

•

When is shown in standby mode, the Bluetooth connection is active.

When is blinking, your phone is trying to connect to the other device.

When is shown continuously, the Bluetooth connection is active.

Paired devices view

Paired devices are easier to recognise, they are indicated by in the search result

list. In the Bluetooth main view, press

to open a list of paired devices (

172

•

To pair with a device: Select Options→New paired device. The phone starts a

device search. Scroll to the device you want to pair with and press Select.

Exchange passcodes. The device is added to the Paired devices list.

To cancel pairing: Scroll to the device whose pairing you want to cancel and

press

Options→Delete all.

or select Options→Delete. If you want to cancel all pairings, select

If you are currently connected to a device, and delete the pairing with that

device, the pairing is removed and the device connection is terminated, but

Bluetooth connection remains active on the handset.

•

To set a device to be authorised or unauthorised: Scroll to the device and

select Options→Set as authorised - Connections between your phone and this

device can be made without your knowledge. No separate acceptance or

authorisation is needed. Use this status only for your own devices that others

do not have access to, for example your PC, or devices that belong to someone

you trust. The icon is added next to authorised devices in the Paired devices

view. Set as unauthorised - Connection requests from this device need to be

accepted separately every time.

Receiving data via Bluetooth wireless technology

When you receive data via Bluetooth wireless technology, a tone sound is played

and you are asked if you want to accept the message. If you accept, the item is

placed in the Inbox folder in Messaging. Messages received via Bluetooth

technology are indicated by

. See “Inbox - receiving messages” on page 90.

173

Disconnecting Bluetooth connection

A Bluetooth connection is disconnected automatically after sending or receiving

data.

■ Infrared connection

Go to Menu→Connectivity→Infrared.

Via infrared, you can send or receive data such as business cards and calendar

notes to and from a compatible phone or data device.

Do not point the IR (infrared) beam at anyone's eye or allow it to interfere with other IR

devices. This device is a Class 1 laser product.

Sending and receiving data via infrared

1. Make sure that the infrared ports of the sending and receiving devices are

pointing at each other and that there are no obstructions between the devices.

The preferable distance between the two devices is 1 metre at most. See “Keys

and connectors” on page 26.

2. The user of the receiving device activates the infrared port.

To activate the infrared port of your phone to receive data via infrared, go to

Menu→Connectivity→Infrared.

3. The user of the sending device selects the desired infrared function to start

data transfer.

To send data via infrared, select Options→Send→Via infrared in an

application.

174

If data transfer is not started within 1 minute after the activation of the

infrared port, the connection is cancelled and must be started again.

All items that are received via infrared are placed in the Inbox folder in Messaging.

New infrared message are indicated by

Tip: Microsoft Windows 2000: To be able to use infrared to transfer files

between your phone and a compatible computer, go to Control Panel and

select Wireless Link. In the Wireless Link File Transfer tab, check the Allow

others to send files to your computer using infrared. After transferring the

files, it is advisable to change back the default settings to prevent

unauthorized file transfer.

Checking the status of the infrared connection

•

When

blinks, your phone is trying to connect to the other device or a

connection has been lost.

•

When

is shown continuously, the infrared connection is active and your

phone is ready to send and receive data via its infrared port.

■ VPN

Virtual Private Network (VPN) connections allow you to create encrypted

connections over unsecured networks like the Internet. VPN connections require

VPN policies, which define how network transactions are protected, and an

Internet access point.

175

A virtual private network connection provides privacy, integrity, and

nonrepudiation of data, as well as authentication and authorisation for access to

networks and network services.

System administrators provide VPN policies.

■ Connection manager

Go to Menu→Connectivity→Connection manager.

In the Connection manager, you can identify the status of multiple data

connections, view details on the amount of data sent and received, and end

unused connections.

You can view details of data connections only. Voice calls are not listed.

When you open the Connection manager, you can see a list of:

•

Open data connections,

- Data call,

- GPRS.

The status of each connection.

Amount of data uploaded and downloaded for each connection (GPRS

connections only).

•

The duration of each connection (Data call connections only).

Note: The actual time invoiced for calls by your service provider may vary,

depending on network features, rounding off for billing, and so forth.

Options in the Connection manager main view when there are one or more

connections are: Details, Disconnect, Disconnect all, Help and Exit.

176

Viewing connection details

To view the details of a connection, scroll to a connection and select

Options→Details. The following is displayed:

•

Name - The name of the Internet Access Point (IAP) in use.

Bearer - The type of data connection: Data call or GPRS.

Status - The current status of the connection.

Received - The amount of data, in bytes, received to the phone.

Sent - The amount of data, in bytes, sent from the phone.

Duration - The length of time that the connection has been open.

Speed - The current speed of both sending and receiving data in kB/s (kilobytes

per second).

•

Dial-up (GSM) - The dial-up number used, or Name (GPRS) - access point name

used.

Shared (not displayed if the connection is not shared) - The number of

applications using the same connection.

Ending connections

•

Scroll to a connection and select Options→Disconnect to end that connection

only.

•

Select Options→Disconnect all to close all currently open connections.

177

■ Connecting your phone to a compatible computer

For further information on how to make a connection to a compatible computer

via USB, infrared or Bluetooth technology, and how to install Nokia PC Suite 6.2,

see the Quick Guide for Nokia PC Suite on the CD-ROM. For further information on

how to use Nokia PC Suite, see the help function on PC Suite or visit the support

pages at www.nokia.com.

■ Using your phone as a modem

Go to Menu→Connectivity→Modem.

Use your phone as a modem to connect to the Internet with a compatible PC, or to

send and receive faxes.

Detailed installation instructions can be found in Quick guide for Modem Options

for Nokia 6260 on the CD-ROM supplied with the phone.

■ Remote synchronisation

Go to Menu→Connectivity→Sync.

The Sync application enables you to synchronise your calendar or contacts with

various calendar and address book applications on a compatible computer or on

the Internet. Synchronisation takes place over a GSM data call or packet data

connection.

178

The synchronisation application uses SyncML technology for synchronisation. For

information on SyncML compatibility, contact the supplier of the calendar or

address book application you want to synchronise your phone data with.

Creating a new synchronisation profile

Options in the Remote sync main view are: Synchronise, New sync profile,

Edit sync profile, Delete, View log, Help, and Exit.

1. If no profiles have been defined, the phone asks you if you want to create a

new profile. Select Yes.

To create a new profile in addition to existing ones, select Options→New sync

profile. Choose whether you want to use the default setting values or copy the

values from an existing profile to be used as the basis for the new profile.

2. Define the following:

Sync profile name - Write a descriptive name for the profile.

Access point - Select an access point you want to use for the data connection.

Host address - Contact your service provider or system administrator for the

correct values.

Port - Contact your service provider or system administrator for the correct

values.

User name - Your user ID for the synchronisation server. Contact your service

provider or system administrator for your correct ID.

Password - Write your password. Contact your service provider or system

administrator for the correct value.

179

Press

and select the application that you wish to synchronise.

The available applications that you can synchronise may vary. Contact your

service provider for more information.

3. Press Done to save the settings.

Synchronising data

In the Sync main view, you can see the different profiles, and what kind of data

are synchronised: Calendar, Contacts, or both.

1. In the main view, scroll to a profile and select Options→Synchronise. The

status of the synchronisation is shown at the bottom of the screen.

To cancel synchronisation before it is finished, press Cancel.

2. You are notified when the synchronisation has been completed.

•

After synchronisation is complete, select Options→View log to open a log file

showing the synchronisation status (Complete or Incomplete) and how many

calendar or contact entries have been added, updated, deleted, or discarded

(not synchronised) in the phone or on the server.

180

13. Troubleshooting

Memory low

When the following notes are shown, the phone memory is low and you must start

to delete some data: Not enough memory to perform operation. Delete some data

first. or Memory low. Delete some data. To view what kind of data you have and

how much memory the different data groups consume, go to File manager and

select Options→Memory details.

You may want to delete the following items regularly to avoid memory getting

low:

•

Messages from the Inbox, Drafts, and Sent folders in Messaging.

Retrieved e-mail messages from the phone memory.

Saved browser pages.

Images and photos in Images.

To delete contact information, calendar notes, call timers, call cost timers, game

scores, or any other data, go to the respective application to remove the data.

If you are deleting multiple items and another of the following notes are shown:

Not enough memory to perform operation. Delete some data first. or Memory low.

Delete some data. try deleting items one by one (starting from the smallest item).

Clearing the calendar memory - To remove more than one event at a time, go to

the Month view and select Options→Delete entry→ and either:

181

•

Before date - to delete all calendar notes which take place before a certain

date. Enter the date before which all calendar notes are deleted.

All entries - to delete all calendar notes.

Erasing log information - To erase all the log contents, Recent calls register, and

Messaging delivery reports permanently, go to Logs and select Options→Clearlog

or go to Settings→Log duration→No log.

Different ways to store data:

•

Use Nokia PC Suite 6.2 to make a backup copy of all data to a compatible

computer.

•

Send images to your e-mail address and then save the images to your

computer (network service).

•

Send data via infrared or Bluetooth technology to a compatible device.

Store data on a compatible memory card.

■ Q&A

Phone display

•

Q. Why do missing, discoloured or bright dots appear on the screen every time I

turn on my phone?

A. This is a characteristic of this type of display. Some displays may contain

pixels or dots that remain on or off. This is normal, not a fault.

182

Camera

Q: Why do images look smudgy?

A: Check that the camera lens protection window is clean.

•

Bluetooth

•

Q: Why can’t I end a Bluetooth connection?

A: If another device is connected to your phone, you can either end the

connection using the other device or by deactivating Bluetooth. Go to

Bluetooth and select the setting Bluetooth→Off.

•

Q: Why can’t I find my friend’s Bluetooth-enabled device.

A: Check that both you and your friend have activated Bluetooth.

Check that the distance between the two devices is not over 10 metres or that

there are no walls or other obstructions between the devices.

Check that the other device is not in ‘Hidden’ mode.

Check that both devices are compatible.

Multimedia messaging

•

Q: What should I do when the phone tells me that it cannot receive a

multimedia message because the memory is full?

A: The amount of memory needed is indicated in the error message: Not

enough memory to retrieve message. Delete some data first. To view what kind

of data you have and how much memory the different data groups consume,

go to File manager and select Options→Memory details.

183

•

Q: How can I end the data connection when the phone starts a data

connection again and again? The brief notes on the display state that the

phone is retrieving or trying to retrieve a message. What is happening?

A: The phone is trying to retrieve a multimedia message from the multimedia

messaging centre.

Check that the settings for multimedia messaging have been defined correctly

and that there are no mistakes in phone numbers or addresses. Go to

Messaging and select Options→Settings→Multimedia message.

To stop the phone from making a data connection, you have the following

options. Go to Messaging and select Options→Settings→Multimedia

message, and then:

•

Select On receiving msg.→Defer retrieval if you want the multimedia

messaging centre to save the message to be retrieved later, for example,

after you have checked the settings. After this change, the phone still needs

to send information notes to the network. To retrieve the message later,

select Retr. immediately.

•

Select On receiving msg.→Reject message - if you want to reject all

incoming multimedia messages. After this change, the phone needs to send

information notes to the network and the multimedia-messaging centre

deletes all multimedia messages that are waiting to be sent to you.

Select Multimedia reception→Off - if you want to ignore all incoming

multimedia messages. After this change, the phone will not make any

network connections related to multimedia messaging.

184

Messaging

Q: Why can’t I select a contact?

•

A: If you cannot select a contact in the Contacts directory, the contact card

does not have a phone number or an e-mail address. Add the missing

information to the contact card in the Contacts application.

Calendar

Q: Why are the week numbers missing?

•

A: If you have changed the Calendar settings so that the week starts on a day

other than Monday, then the week numbers are not shown.

Browser Services

•

Q: No valid access point defined. Define one in Web settings.

A: Insert proper browser settings. Contact your service provider for

instructions.

Log

Q: Why does the log appear to be empty?

•

A: You may have activated a filter, and no communication events fitting that

filter have been logged. To see all events, select Options→Filter→All

communication.

PC connectivity

•

Q: Why do I have problems in connecting the phone to my PC?

A: Make sure that Nokia PC Suite 6.2 is installed and running on your PC. See

the Quick Guide for Nokia PC Suite on the CD-ROM. For further information on

185

how to use Nokia PC Suite, see the help function on PC Suite or visit the

support pages at www.nokia.com.

Access codes

•

Q: What is my password for the lock, PIN, or PUK codes?

A: The default lock code is 12345. If you forget or lose the lock code, contact

your phone dealer.

If you forget or lose a PIN or PUK code, or if you have not received such a code,

contact your network service provider.

For information about passwords, contact your access point provider, for

example, a commercial Internet Service Provider (ISP), service provider, or

network operator.

Application not responding

•

Q: How do I close an application that is not responding?

A: Open the application switching window by pressing and holding

. Then

scroll to the application, and press

to close the application.

186

14. Battery information

Your device is powered by a rechargeable battery. The full performance of a new

battery is achieved only after two or three complete charge and discharge cycles.

The battery can be charged and discharged hundreds of times but it will

eventually wear out. When the talk and standby times are noticeably shorter than

normal, buy a new battery. Use only Nokia-approved batteries, and recharge your

battery only with Nokia-approved chargers designated for this device.

Unplug the charger from the electrical plug and the device when not in use. Do

not leave the battery connected to a charger. Overcharging may shorten its

lifetime. If left unused, a fully charged battery loses its charge over time.

Temperature extremes can affect the ability of your battery to charge.

Always switch the device off and disconnect the charger before removing the

battery.

Check the model number of any charger before use with this device. This device is

intended for use when supplied with power from AC-1, ACP-7, ACP-8, ACP-9,

ACP-12, LCH-8, LCH-9, or LCH-12 chargers.

To prolong the battery life of NiMh batteries, discharge the battery from time to

time by leaving your device switched on until it turns itself off. Do not attempt to

discharge the battery by any other means.

Use the battery only for its intended purpose. Never use any charger or battery

that is damaged.

187

Do not short-circuit the battery. Accidental short-circuiting can occur when a

metallic object such as a coin, clip, or pen causes direct connection of the positive

(+) and negative (-) terminals of the battery. (These look like metal strips on the

battery.) This might happen, for example, when you carry a spare battery in your

pocket or purse. Short-circuiting the terminals may damage the battery or the

connecting object.

Leaving the battery in hot or cold places, such as in a closed car in summer or

winter conditions, reduces the capacity and lifetime of the battery. Always try to

keep the battery between 15°C and 25°C (59°F and 77°F). A device with a hot or

cold battery may not work temporarily, even when the battery is fully charged.

Battery performance is particularly limited in temperatures well below freezing.

Do not dispose of batteries in a fire! Dispose of batteries according to local

regulations. Recycle when possible. Do not dispose as household waste.

Warning: Use only batteries, chargers, and enhancements approved by

Nokia for use with this particular model. The use of any other types may

invalidate any approval or warranty, and may be dangerous.

For availability of approved enhancements, check with your dealer. When you

disconnect the power cord of any enhancement, grasp and pull the plug, not the

cord.

Your device and its enhancements may contain small parts. Keep them out of

reach of small children.

188

A few practical rules about accessories and enhancements.

•

Keep all accessories and enhancements out of the reach of small children.

•

When you disconnect the power cord of any accessory or enhancement, grasp

and pull the plug, not the cord.

•

Check regularly that enhancements installed in a vehicle are mounted and are

operating properly.

Installation of any complex car enhancements must be made by qualified

personnel only.

189

Care and Maintenance

Your device is a product of superior design and craftsmanship and should be treated with

care. The suggestions below help you protect your warranty coverage.

•

Keep the device dry. Precipitation, humidity and all types of liquids or moisture can

contain minerals that corrode electronic circuits. If your device does get wet, remove the

battery and allow the device to dry completely before replacing it.

•

Do not use or store the device in dusty, dirty areas. Its moving parts and electronic

components can be damaged.

Do not store the device in hot areas. High temperatures can shorten the life of electronic

devices, damage batteries, and warp or melt certain plastics.

Do not store the device in cold areas. When the device returns to its normal temperature,

moisture can form inside the device and damage electronic circuit boards.

•

Do not attempt to open the device other than as instructed in this guide.

Do not drop, knock, or shake the device. Rough handling can break internal circuit boards

and fine mechanics.

•

Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the device.

Do not paint the device. Paint can clog the moving parts and prevent proper operation.

Use a soft, clean, dry cloth to clean any lenses (such as camera, proximity sensor, and

light sensor lenses).

•

Use only the supplied or an approved replacement antenna. Unauthorised antennas,

modifications, or attachments could damage the device and may violate regulations

governing radio devices.

190

All of the above suggestions apply equally to your device, battery, charger, or any

enhancement. If any device is not working properly, take it to the nearest authorized service

facility for service.

191

Additional safety information

■ Operating environment

Remember to follow any special regulations in force in any area and always switch off your

device when its use is prohibited or when it may cause interference or danger. Use the device

only in its normal operating positions. To maintain compliance with radio frequency

exposure guidelines only use enhancements approved by Nokia for use with this device.

When the device is on and being worn on the body, always use an approved holder or

carrying case.

Parts of the device are magnetic. Metallic materials may be attracted to the device, and

persons with a hearing aid should not hold the device to the ear with the hearing aid. Always

secure the device in its holder, because metallic materials may be attracted by the earpiece.

Do not place credit cards or other magnetic storage media near the device, because

information stored on them may be erased.

■ Medical devices

Operation of any radio transmitting equipment, including wireless phones, may interfere

with the functionality of inadequately protected medical devices. Consult a physician or the

manufacturer of the medical device to determine if they are adequately shielded from

external RF energy or if you have any questions. Switch off your device in health care

facilities when any regulations posted in these areas instruct you to do so. Hospitals or

health care facilities may be using equipment that could be sensitive to external RF energy.

Pacemakers

Pacemaker manufacturers recommend that a minimum separation of 6 in. (15.3 cm) be

maintained between a wireless phone and a pacemaker to avoid potential interference with

192

the pacemaker. These recommendations are consistent with the independent research by

and recommendations of Wireless Technology Research. Persons with pacemakers should:

•

always keep the device more than 6 in. (15.3 cm) from their pacemaker when the device

is switched on;

•

not carry the device in a breast pocket; and

hold the device to the ear opposite the pacemaker to minimise the potential for

interference.

If you have any reason to suspect that interference is taking place, switch off your device

immediately.

Hearing aids

Some digital wireless devices may interfere with some hearing aids. If interference occurs,

consult your service provider.

■ Vehicles

RF signals may affect improperly installed or inadequately shielded electronic systems in

motor vehicles such as electronic fuel injection systems, electronic antiskid (antilock)

braking systems, electronic speed control systems, air bag systems. For more information,

check with the manufacturer or its representative of your vehicle or any equipment that has

been added.

Only qualified personnel should service the device, or install the device in a vehicle. Faulty

installation or service may be dangerous and may invalidate any warranty that may apply to

the device. Check regularly that all wireless device equipment in your vehicle is mounted

and operating properly. Do not store or carry flammable liquids, gases, or explosive materials

in the same compartment as the device, its parts, or enhancements. For vehicles equipped

with an air bag, remember that air bags inflate with great force. Do not place objects,

including installed or portable wireless equipment in the area over the air bag or in the air

193

bag deployment area. If in-vehicle wireless equipment is improperly installed and the air bag

inflates, serious injury could result.

Using your device while flying in aircraft is prohibited. Switch off your device before

boarding an aircraft. The use of wireless teledevices in an aircraft may be dangerous to the

operation of the aircraft, disrupt the wireless telephone network, and may be illegal.

■ Potentially explosive environments

Switch off your device when in any area with a potentially explosive atmosphere and obey

all signs and instructions. Potentially explosive atmospheres include areas where you would

normally be advised to turn off your vehicle engine. Sparks in such areas could cause an

explosion or fire resulting in bodily injury or even death. Switch off the device at refuelling

points such as near gas pumps at service stations. Observe restrictions on the use of radio

equipment in fuel depots, storage, and distribution areas, chemical plants or where blasting

operations are in progress. Areas with a potentially explosive atmosphere are often but not

always clearly marked. They include below deck on boats, chemical transfer or storage

facilities, vehicles using liquefied petroleum gas (such as propane or butane), and areas

where the air contains chemicals or particles such as grain, dust or metal powders.

■ Safety information about video games

About photosensitive seizures

A very small percentage of people may experience a seizure when exposed to certain visual

images, including flashing lights or patterns that may appear in video games. Even people

who have no history of seizures or epilepsy may have an undiagnosed condition that can

cause photosensitive epileptic seizures while watching video games. These seizures may

have a variety of symptoms, including lightheadedness, altered vision, eye or face twitching,

jerking or shaking of arms or legs, disorientation, confusion, or momentary loss of

194

awareness. Seizures may also cause loss of consciousness or convulsions that can lead to

injury from falling down or striking nearby objects.

Immediately stop playing and consult a doctor if you experience any of these symptoms.

Adults who allow teenagers (or children) to play the games should watch for or ask their

children about these symptoms as they are more likely than adults to experience these

seizures. The risk of photosensitive epileptic seizures may be reduced by playing in a well-lit

room and by not playing when you are drowsy or fatigued. If you or any of your relatives

have a history of seizures or epilepsy, consult a doctor before playing.

Play safely

Take a break from playing games at least every half hour. Stop playing immediately if you

begin to feel tired of if you experience an unpleasant sensation or pain in your hands and/or

arms. If the condition persists, consult a doctor.

Use of vibration can aggravate injuries. Do not turn vibration on if you have any ailment in

the bones or joints of your fingers, hands, wrists, or arms.

■ Emergency calls

Important: Wireless phones, including this device, operate using radio signals,

wireless networks, landline networks, and user-programmed functions. Because of

this, connections in all conditions cannot be guaranteed. You should never rely

solely on any wireless device for essential communications like medical

emergencies.

To make an emergency call:

1. If the device is not on, switch it on. Check for adequate signal strength.

Some networks may require that a valid SIM card is properly inserted in the device.

2. Press

as many times as needed to clear the display and ready the device for calls.

195

3. Key in the official emergency number for your present location. Emergency numbers vary

by location.

4. Press

If certain features are in use, you may first need to turn those features off before you can

make an emergency call. If the device is in offline or flight mode you must change the profile

to activate the phone function before you can make an emergency call. Consult this guide or

your service provider for more information.

When making an emergency call, give all the necessary information as accurately as

possible. Your wireless device may be the only means of communication at the scene of an

accident. Do not end the call until given permission to do so.

■ Certification information (SAR)

THIS DEVICE MEETS INTERNATIONAL GUIDELINES FOR EXPOSURE TO RADIO WAVES

Your mobile device is a radio transmitter and receiver. It is designed and manufactured not

to exceed the limits for exposure to radio frequency (RF) recommended by international

guidelines (ICNIRP). These limits are part of comprehensive guidelines and establish

permitted levels of RF energy for the general population. The guidelines were developed by

independent scientific organisations through periodic and thorough evaluation of scientific

studies. The guidelines include a substantial safety margin designed to assure the safety of

all persons, regardless of age and health.

The exposure standard for mobile devices employs a unit of measurement known as the

Specific Absorption Rate, or SAR. The SAR limit stated in the international guidelines is 2.0

W/kg*. Tests for SAR are conducted using standard operating positions with the device

transmitting at its highest certified power level in all tested frequency bands. Although the

SAR is determined at the highest certified power level, the actual SAR of the device while

operating can be well below the maximum value. This is because the device is designed to

196

operate at multiple power levels so as to use only the power required to reach the network.

In general, the closer you are to a base station, the lower the power output of the device.

The highest SAR value for this device when tested for use at the ear is 0.72 W/kg.

This device meets RF exposure guidelines when used either in the normal use position

against the ear or when positioned at least 2,2 cm away from the body. When a carry case,

belt clip or holder is used for body-worn operation, it should not contain metal and should

position the product at least 2,2 cm away from your body.

In order to transmit data files or messages, this device requires a quality connection to the

network. In some cases, transmission of data files or messages may be delayed until such a

connection is available. Ensure the above separation distance instructions are followed until

the transmission is completed.

* The SAR limit for mobile devices used by the public is 2.0 watts/kilogram (W/kg) averaged

over ten grams of body tissue. The guidelines incorporate a substantial margin of safety to

give additional protection for the public and to account for any variations in measurements.

SAR values may vary depending on national reporting requirements and the network band.

For SAR information in other regions look under product information at www.nokia.com.

197

ZALMAN TNN 500AF User Manual
West Bend 40053 User Manual
Sony CDX S2050C User Manual
Seagate U8TM FAMILY ST34313A User Manual
Seagate ST3250823NS User Manual
Seagate Enterprise Value ST3000NC002 User Manual
Samsung GH68 07155A User Manual
Panasonic SUPERDISK CF VFS271 User Manual
Panasonic 6630 User Manual
Palm TREOPROBLKSPT User Manual