Product Manual
®
Pulsar XT.2 SAS
Standard Models
Self-Encrypting Drive Models
ST400FX0012
ST400FX0002
ST200FX0002
ST100FX0002
100647497
Rev. B
June 2011
Contents
Seagate Technology support services. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Scope. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Applicable standards and reference documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Electromagnetic compatibility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Electromagnetic compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Reference documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
General description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Standard features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Media description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Formatted capacities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Programmable drive capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Factory-installed options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Thin Provisioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Logical Block Provisioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Thin Provisioning capabilities. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
UNMAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
FORMAT UNIT command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Protection Information (PI) and Security (SED) . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Performance characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Internal drive characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Performance characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Access time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Performance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Start/stop time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Cache control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Caching write data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Reliability specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Error rates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Unrecoverable Errors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Interface errors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Endurance Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Wear Leveling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Garbage Collection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Write Amplification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
UNMAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Data Retention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Lifetime Endurance Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Reliability and service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
6.3.6
Preventive maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Hot plugging the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
S.M.A.R.T. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Thermal monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Drive Self Test (DST). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Pulsar XT.2 SAS Product Manual, Rev. B
i
Product warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Power specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
7.1.1 Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
DC power requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Current profiles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Power dissipation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Environmental limits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Relative humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Air cleanliness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Electromagnetic susceptibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Mechanical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Power requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Drive internal defects/errors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Drive error recovery procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Drive orientation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Cooling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Drive mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
11.1 SAS features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
11.1.2
ii
Pulsar XT.2 SAS Product Manual, Rev. B
Dual port support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
SCSI commands supported. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
INQUIRY data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
MODE SENSE data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Miscellaneous operating features and conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
SAS physical interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Physical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Connector requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Electrical description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Pin descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
SAS transmitters and receivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Signal characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Ready LED Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Differential signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
11.7
SAS-2 Specification compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Additional information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Pulsar XT.2 SAS Product Manual, Rev. B
iii
iv
Pulsar XT.2 SAS Product Manual, Rev. B
List of Figures
Current profiles for 400GB models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Current profiles for 200GB models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Current profiles for 100GB models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Temperature check point location - 15mm drives. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Temperature check point location - 7mm drives. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Recommended mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Figure 10. Mounting configuration dimensions (400GB models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Figure 11. Mounting configuration dimensions (200 & 100GB models). . . . . . . . . . . . . . . . . . . . . . . . . . 34
Figure 12. Physical interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Figure 13. Air flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Figure 14. Physical interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Figure 15. SAS device plug dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Figure 16. SAS device plug dimensions (detail) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Figure 17. SAS transmitters and receivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Pulsar XT.2 SAS Product Manual, Rev. B
v
1.0
Seagate Technology support services
SEAGATE ONLINE SUPPORT and SERVICES
For information regarding products and services, visit http://www.seagate.com/www/en-us/about/contact_us/
Available services include:
Presales & Technical support
Global Support Services telephone numbers & business hours
Authorized Service Centers
For information regarding Warranty Support, visit
http://www.seagate.com/www/en-us/support/warranty_&_returns_assistance
Pulsar XT.2 SAS Product Manual, Rev. B
1
2.0
Scope
This manual describes Seagate Technology® LLC, Pulsar® XT.2 SAS (Serial Attached SCSI) drives.
Pulsar XT.2 drives support the SAS Protocol specifications to the extent described in this manual. The SAS
Interface Manual (part number 100293071) describes the general SAS characteristics of this and other Sea-
gate SAS drives. The Self-Encrypting Drive Reference Manual, part number 100515636, describes the inter-
face, general operation, and security features available on Self-Encrypting Drive models.
Product data communicated in this manual is specific only to the model numbers listed in this manual. The data
listed in this manual may not be predictive of future generation specifications or requirements. If you are
designing a system which will use one of the models listed or future generation products and need further
assistance, please contact your Field Applications Engineer (FAE) or our global support services group as
shown in Section 1.0.
Unless otherwise stated, the information in this manual applies to standard and Self-Encrypting Drive models.
Standard models
ST400FX0002
ST200FX0002
ST100FX0002
Standard SED models
ST400FX0012
Note. Previous generations of Seagate Self-Encrypting Drive models were called Full Disk Encryption
(FDE) models before a differentiation between drive-based encryption and other forms of encryp-
tion was necessary.
Note. The Self-Encrypting Drive models indicated on the cover of this product manual have provisions for
“Security of Data at Rest” based on the standards defined by the Trusted Computing Group (see
www.trustedcomputinggroup.org).
2
Pulsar XT.2 SAS Product Manual, Rev. B
3.0
Applicable standards and reference documentation
The drives documented in this manual have been developed as system peripherals to the highest standards of
design and construction. The drives depend on host equipment to provide adequate power and environment
for optimum performance and compliance with applicable industry and governmental regulations. Special
attention must be given in the areas of safety, power distribution, shielding, audible noise control, and temper-
ature regulation. In particular, the drives must be securely mounted to guarantee the specified performance
characteristics. Mounting by bottom holes must meet the requirements of Section 10.3.
3.1
Standards
The Pulsar XT.2 family complies with Seagate standards as noted in the appropriate sections of this manual
and the Seagate SAS Interface Manual, part number 100293071.
The drives are recognized in accordance with UL 60950 and CSA 60950 as tested by UL(CSA) and EN60950
as tested by TUV.
The security features of Self-Encrypting Drive models are based on the “TCG Storage Architecture Core Spec-
ification” and the “TCG Storage Workgroup Security Subsystem Class: Enterprise_A” specification with addi-
tional vendor-unique features as noted in this product manual.
3.1.1
Electromagnetic compatibility
The drive, as delivered, is designed for system integration and installation into a suitable enclosure prior to
use. The drive is supplied as a subassembly and is not subject to Subpart B of Part 15 of the FCC Rules and
Regulations nor the Radio Interference Regulations of the Canadian Department of Communications.
The design characteristics of the drive serve to minimize radiation when installed in an enclosure that provides
reasonable shielding. The drive is capable of meeting the Class B limits of the FCC Rules and Regulations of
the Canadian Department of Communications when properly packaged; however, it is the user’s responsibility
to assure that the drive meets the appropriate EMI requirements in their system. Shielded I/O cables may be
required if the enclosure does not provide adequate shielding. If the I/O cables are external to the enclosure,
shielded cables should be used, with the shields grounded to the enclosure and to the host controller.
3.1.1.1
Electromagnetic susceptibility
As a component assembly, the drive is not required to meet any susceptibility performance requirements. It is
the responsibility of those integrating the drive within their systems to perform those tests required and design
their system to ensure that equipment operating in the same system as the drive or external to the system
does not adversely affect the performance of the drive. See Tables 8 through 10, DC power requirements.
Pulsar XT.2 SAS Product Manual, Rev. B
3
3.1.2
Electromagnetic compliance
Seagate uses an independent laboratory to confirm compliance with the directives/standards for CE Marking
and C-Tick Marking. The drive was tested in a representative system for typical applications. The selected sys-
tem represents the most popular characteristics for test platforms. The system configurations include:
• Typical current use microprocessor
• Keyboard
• Monitor/display
• Printer
• Mouse
Although the test system with this Seagate model complies with the directives/standards, we cannot guarantee
that all systems will comply. The computer manufacturer or system integrator shall confirm EMC compliance
and provide the appropriate marking for their product.
Electromagnetic compliance for the European Union
If this model has the CE Marking it complies with the European Union requirements of the Electromagnetic
Compatibility Directive 2004/108/EC as put into place on 20 July 2007.
Australian C-Tick
If this model has the C-Tick Marking it complies with the Australia/New Zealand Standard AS/NZ CISPR22 and
meets the Electromagnetic Compatibility (EMC) Framework requirements of Australia’s Spectrum Manage-
ment Agency (SMA).
Korean KCC
If these drives have the Korean Communications Commission (KCC) logo, they comply with KN22 and
KN61000.
Taiwanese BSMI
If this model has the Taiwanese certification mark then it complies with Chinese National Standard, CNS13438.
3.1.3
European Union Restriction of Hazardous Substances (RoHS)
The European Union Restriction of Hazardous Substances (RoHS) Directive restricts the presence of chemical
substances, including Lead (Pb), in electronic products effective July 2006.
A number of parts and materials in Seagate products are procured from external suppliers. We rely on the rep-
resentations of our suppliers regarding the presence of RoHS substances in these parts and materials. Our
supplier contracts require compliance with our chemical substance restrictions, and our suppliers document
their compliance with our requirements by providing material content declarations for all parts and materials for
the drives documented in this publication. Current supplier declarations include disclosure of the inclusion of
any RoHS-regulated substance in such parts or materials.
Seagate also has internal systems in place to ensure ongoing compliance with the RoHS Directive and all laws
and regulations which restrict chemical content in electronic products. These systems include standard operat-
ing procedures that ensure that restricted substances are not utilized in our manufacturing operations, labora-
tory analytical validation testing, and an internal auditing process to ensure that all standard operating
procedures are complied with.
4
Pulsar XT.2 SAS Product Manual, Rev. B
3.1.4
China Restriction of Hazardous Substances (RoHS) Directive
This product has an Environmental Protection Use Period (EPUP) of 20 years. The following
table contains information mandated by China's "Marking Requirements for Control of Pollution
Caused by Electronic Information Products" Standard.
"O" indicates the hazardous and toxic substance content of the part (at the homogenous material level) is lower
than the threshold defined by the China RoHS MCV Standard.
"X" indicates the hazardous and toxic substance content of the part (at the homogenous material level) is over
the threshold defined by the China RoHS MCV Standard.
3.2
Reference documents
SCSI Commands Reference Manual
SAS Interface Manual
Seagate part number: 100293068
Seagate part number: 100293071
ANSI SAS Documents
SFF-8223
2.5” Drive Form Factor with Serial Connector
HSS Backplane Design Guidelines
SFF-8460
SFF-8470
Multi Lane Copper Connector
SFF-8482
SAS Plug Connector
ANSI INCITS.xxx
Serial Attached SCSI (SAS-2) Standard (T10/1760-D)
SCSI Architecture Model-3 (SAM-4) Standard (T10/1683-D)
SCSI Primary Commands-3 (SPC-4) Standard (T10/1731-D)
SCSI Block Commands-3 (SBC-3) Standard (T10/1799-D)
ISO/IEC 14776-xxx
ISO/IEC 14776-xxx
ISO/IEC 14776-xxx
ANSI Small Computer System Interface (SCSI) Documents
X3.270-1996
(SCSI-3) Architecture Model
Trusted Computing Group (TCG) Documents (apply to Self-Encrypting Drive models only)
TCG Storage Architecture Core Specification, Rev. 1.0
TCG Storage Security Subsystem Class Enterprise Specification, Rev. 1.0
Self-Encrypting Drives Reference Manual
Seagate part number: 100515636
JEDEC Standards
JESD218 - Solid-State Drive (SSD) Requirements and Endurance Test Method
JESD219 - Solid-State Drive (SSD) Endurance Workloads
In case of conflict between this document and any referenced document, this document takes precedence.
Pulsar XT.2 SAS Product Manual, Rev. B
5
4.0
General description
Pulsar XT.2 drives provide high performance, high capacity data storage for a variety of systems with a Serial
Attached SCSI (SAS) interface. The Serial Attached SCSI interface is designed to meet next-generation com-
puting demands for performance, scalability, flexibility and high-density storage requirements.
Pulsar XT.2 drives are random access storage devices designed to support the Serial Attached SCSI Protocol
as described in the ANSI specifications, this document, and the SAS Interface Manual (part number
100293071) which describes the general interface characteristics of this drive. Pulsar XT.2 drives are classified
as intelligent peripherals and provide level 2 conformance (highest level) with the ANSI SCSI-1 standard. The
SAS connectors, cables and electrical interface are compatible with Serial ATA (SATA), giving future users the
choice of populating their systems with either SAS or SATA drives. This allows users to continue to leverage
existing investment in SCSI while gaining a 6Gb/s serial data transfer rate.
The Self-Encrypting Drive models indicated on the cover of this product manual have provisions for “Security
group.org).
Note. Never disassemble and do not attempt to service items in the enclosure. The drive does not contain
user-replaceable parts. Opening for any reason voids the drive warranty.
4.1
Standard features
Pulsar XT.2 SAS drives have the following standard features:
• 1.5 / 3.0 / 6.0 Gb Serial Attached SCSI (SAS) interface
• Integrated dual port SAS controller supporting the SCSI protocol
• Support for SAS expanders and fanout adapters
• Firmware downloadable using the SAS interface
• 128 - deep task set (queue)
• Supports up to 32 initiators
• Jumperless configuration
• User-selectable logical block size (512, 520, 524, 528, 4096, 4160, 4192, or 4224 bytes per logical block)
• Industry standard SFF 2.5-inch dimensions
• ECC maximum burst correction length of 90 bits
• No preventive maintenance or adjustments required
• Self diagnostics performed when power is applied to the drive
• Vertical, horizontal, or top down mounting
• Drive Self Test (DST)
• Background Media Scan (BMS)
• Parallel flash access channels
• Power loss data protection
• Thin Provisioning with Block Unmap Support
• Silent operation
• Lifetime Endurance Management
Pulsar XT.2 SAS Self-Encrypting Drive models have the following additional features:
6
Pulsar XT.2 SAS Product Manual, Rev. B
• Automatic data encryption/decryption
• Controlled access
• Random number generator
• Drive locking
• 16 independent data bands
• Cryptographic erase of user data for a drive that will be repurposed or scrapped
• Authenticated firmware download
4.2
Media description
The media used on the drive consists of Single Layer Cell (SLC) NAND Flash for improved reliability and per-
formance.
4.3
Performance
• Programmable multi-segmentable cache buffer
• 600MB/s maximum instantaneous data transfers.
• Background processing of queue
• Non-Volatile Write Cache
Note. There is no significant performance difference between Self-Encrypting Drive and standard (non-
Self-Encrypting Drive) models.
4.4
Reliability
• Annualized Failure Rate (AFR) of 0.44%
• Mean time between failures (MTBF) of 2,000,000 hours
• Incorporates industry-standard Self-Monitoring Analysis and Reporting Technology (S.M.A.R.T.)
• 5-year warranty
Pulsar XT.2 SAS Product Manual, Rev. B
7
4.5
Formatted capacities
Standard OEM models are formatted to 512 bytes per block. The block size is selectable at format time and
must be a multiple of 4 bytes. Users having the necessary equipment may modify the data block size before
issuing a FORMAT UNIT command and obtain different formatted capacities than those listed.
To provide a stable target capacity environment and at the same time provide users with flexibility if they
choose, Seagate recommends product planning in one of two modes:
Seagate designs specify capacity points at certain block sizes that Seagate guarantees current and future
products will meet. We recommend customers use this capacity in project planning, as it ensures a stable
operating point with backward and forward compatibility from generation to generation. The current guaranteed
operating points for this product are shown below. The Capacity stated is identical when the drive is formatted
with or without PI enabled.
Table 1:
Formatted Capacity LBA Count
Capacity (LBAs)
400GB
200GB
100GB
LBA
Size
Decimal
Hex
Decimal
Hex
Decimal
Hex
781,422,768
764,871,800
754,677,072
743,833,040
97,677,846
96,153,847
95,419,848
94,696,970
2E9390B0h
390,721,968
1749F1B0h
195,371,568
BA52230h
512
520
2D970478h
2CFB7550h
2C55FDD0h
5D27216h
5BB30F7h
5AFFDC8h
5A4F60Ah
382,435,904
377,338,536
371,916,520
48,840,246
48,076,924
47,709,924
47,348,485
16CB8240h
167DBAA8h
162AFEE8h
2E93E36h
2DD987Ch
2D7FEE4h
2D27B05h
191,217,952
188,669,272
185,958,264
24,421,446
24,038,462
23,854,962
23,674,243
B65C120h
B3EDD58h
B157F78h
174A446h
16ECC3Eh
16BFF72h
1693D83h
524
528
4096
4160
4192
4224
4.6
Programmable drive capacity
Using the MODE SELECT command, the drive can change its capacity to something less than maximum. See
the MODE SELECT (6) parameter list table in the SAS Interface Manual, part number 100293071. A value of
zero in the Number of Blocks field indicates that the drive will not change the capacity it is currently formatted
to have. A number other than zero and less than the maximum number of LBAs in the Number of Blocks field
changes the total drive capacity to the value in the Number of Blocks field. A value greater than the maximum
number of LBAs is rounded down to the maximum capacity.
4.7
Factory-installed options
OEMs may order the following items which are incorporated at the manufacturing facility during production or
packaged before shipping. Some of the options available are (not an exhaustive list of possible options):
• Other capacities can be ordered depending on sparing scheme and LBA size requested.
• Single-unit shipping pack. The drive is normally shipped in bulk packaging to provide maximum protection
against transit damage. Units shipped individually require additional protection as provided by the single unit
shipping pack. Users planning single unit distribution should specify this option.
• The Safety and Regulatory Agency Specifications, part number 75789512, is usually included with each
standard OEM drive shipped, but extra copies may be ordered.
8
Pulsar XT.2 SAS Product Manual, Rev. B
4.8
Thin Provisioning
4.8.1
Logical Block Provisioning
The drive is designed with a feature called Thin Provisioning. Thin Provisioning is a technique which does not
require Logical Blocks to be associated to Physical Blocks on the storage medium until such a time as needed.
The use of Thin Provisioning is a major factor in SSD products because it reduces the amount of wear leveling
and garbage collection that must be performed. The result is an increase in the products endurance. For more
details on Logical Block Provisioning and Thin Provisioning, Reference the SBC-3 document provided by the
T-10 committee.
4.8.2
Thin Provisioning capabilities
The level of Thin Provisioning support may vary by product model. Devices that support Thin Provisioning are
allowed to return a default data pattern for read requests made to Logical Blocks that have not been mapped to
Physical Blocks by a previous WRITE command.
In order to determine if Thin Provisioning is supported and what features of it are implemented requires the
system to send a READ CAPACITY 16 (9Eh) command to the drive. Thin Provisioning and the READ
CAPACITY 16 (9Eh) command is defined in the Seagate SCSI Command Reference 100293068.
Table 2:
Thin Provisioning Product Configuration
Product Configuration
Non-SED
LBPME
LBPRZ
Supported
Supported
Supported
Not Supported
SED
A logical block provisioning management enabled (LBPME) bit set to one indicates that the logical unit imple-
ments logical block provisioning management. An LBPME bit set to zero indicates that the logical unit is fully
provisioned and does not implement logical block provisioning management.
A logical block provisioning read zeros (LBPRZ) bit set to one indicates that, for an unmapped LBA specified
by a read operation, the device server sends user data with all bits set to zero to the data-in buffer. An LBPRZ
bit set to zero indicates that, for an unmapped LBA specified by a read operation, the device server may send
user data with all bits set to any value to the data-in buffer.
4.8.3
UNMAP
The UNMAP command requests that the device server break the association of a specific Logical Block
address from a Physical Block, thereby freeing up the Physical Block from use and no longer requiring it to
contain user data. An unmapped block will respond to a READ command with data that is determined by the
setting of the LBPRZ bit in the READ CAPACITY parameter data.
4.8.4
FORMAT UNIT command
A device which supports Thin Provisioning will be capable of performing a SCSI FORMAT UNIT command
which allocates Logical Blocks Addresses that are not linked to Physical Block Locations. A FORMAT com-
mand will cause all LBAs to become unmapped.
4.8.5
Protection Information (PI) and Security (SED)
The requirements in this section apply to any device which supports LBA unmapping.
In SCSI devices, umapped LBAs are defined as part of the Thin Provisioning model. Support of the Thin Provi-
sioning model is indicated by the LBPME bit having a value of '1' in the READ CAPACITY (16) parameter data.
Pulsar XT.2 SAS Product Manual, Rev. B
9
When a region of LBA's are erased via cryptographic erase, as part of the erase, the drive shall unmap those
LBAs.
If the host attempts to access an unmapped or trimmed LBA, the drive shall return scrambled data. For a given
LBA, the data shall be identical from access to access, until that LBA is either updated with actual data from
the host or that LBA is cryptographically erased. The drive shall report a value of '0' in the LBPRZ field returned
in the READ CAPACITY (16) parameter data.
If the host attempts to access an unmapped LBA on a drive that has been formatted with Protection Informa-
tion (PI), the drive shall return scrambled PI data for that LBA. Depending on the value of the RDPROTECT
field in the data-access command CDB, this may result in the drive returning a standard PI error to the host.
If the host reduces the addressable capacity of the drive via a MODE SELECT command, the drive shall
unmap or trim any LBA within the inaccessible region of the device.
Additionally, an UNMAP command is not permitted on a locked band.
Table 3:
PI and SED Drive Configuration
Drive Configuration
Standard
Enabled
SED
PI Setting
Disabled
Disabled
Enabled
PROT_EN bit
LBPME bit
0
1
1
1
1
1
0
1
0
1
1
LBPRZ bit
0
PI Check Requested
N/A
Yes
No
N/A
Yes
No
DATA Returned for
Thin Provisioned LBA
0x00
0x00
0x00
Random
None
None
None
Random
PI Returned for
Thin Provisioned LBA
Scrambled
PI data
None
0xFF
0xFF
PI Check Performed
N/A
No
No
No
No
No
N/A
No
Yes
Yes
No
No
Error reported to Host
10
Pulsar XT.2 SAS Product Manual, Rev. B
5.0
Performance characteristics
This section provides detailed information concerning performance-related characteristics and features of Pul-
sar XT.2 drives.
Note. Data provided is based on format at 512-bytes.
5.1
Internal drive characteristics
ST400FX0002
ST400FX0012
400
ST200FX0002
ST100FX0002
100 GB (formatted, rounded off value)
Drive capacity
200
Flash Memory Type
NAND SLC
Emulated LBA Size
512, 520, 524, 528, 4096, 4160, 4192, or 4224
Native Programmable Page Size
Default Transfer Alignment Offset
4096 User Bytes
0
5.2
Performance characteristics
See Section 11.4.1, "SAS physical interface" and the SAS Interface Manual (part number 100293071) for addi-
tional timing details.
5.2.1
Access time
Access measurements are taken with nominal power at 25°C ambient temperature. All times are measured
using drive diagnostics. The specifications in the table below are defined as follows:
• Page-to-page access time is an average of all possible page-to-page accesses in both directions for a
sequentially preconditioned drive.
• Average access time is a true statistical random average of at least 5000 measurements of accesses
between programmable pages on a randomly preconditioned drive.
Table 4:
Typical Access Time (µsec)
1,2
1,2
400GB
100/200 GB
Read
268
Write
133
Read
208
Write
Average
121
121
3
Page to Page
Typical
268
133
207
Average Latency
247
188
1.
2.
3.
Execution time measured from receipt of the Command to the Response.
Assumes no errors.
Typical access times are measured under nominal conditions of temperature, voltage, and horizontal orientation as
measured on a representative sample of drives.
Note. These drives are designed to provide the highest possible performance under typical conditions.
However, due to the nature of Flash memory technologies there are many factors that can result in
values different than those stated in this specification
2.
Pulsar XT.2 SAS Product Manual, Rev. B
11
5.2.2
FORMAT UNIT command execution time for 512-byte LBA’s (minutes)
The device may be formatted as either a Thin Provisioned device or a Fully Provisioned device. The default
format is Thin Provisioned and is recommended for most applications. Thin Provisioning provides the most
flexibility for the device to manage the flash medium to maximize endurance.
Table 5:
Maximum FORMAT UNIT Times (minutes)
Format Mode
DCRT Bit
IP Bit
400GB
200GB
100GB
Configuration
Non-SED
(Default) Thin Provisioned
(Default) Thin Provisioned
Fully Provisioned
DCRT = 0
DCRT = 1
DCRT = 0
DCRT = 1
DCRT = 0
DCRT = 1
DCRT = 0
DCRT = 1
IP = 0
IP = 0
IP = 1
IP = 1
IP = 0
IP = 0
IP = 1
IP = 1
5
5
5
5
Non-SED
5
5
Non-SED
140
100
5
60
30
Non-SED
SED
Fully Provisioned
40
20
(Default) Thin Provisioned
(Default) Thin Provisioned
Fully Provisioned
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
SED
5
SED
140
100
SED
Fully Provisioned
5.2.3
Performance
Performance
Table 6:
Notes 400GB
200GB
100GB
Maximum Burst Transfer Rate
600MB/s
Peak sequential 128KB read/write data transfer rate (MB/s max)
Sustained sequential 128KB read/write data transfer rate (MB/s)
Peak 4KB random read/write command rate (IOPs)
[1]
[1]
[2]
[2]
360/300
300/300
300/200
300/100
48,000/22,000
Sustained 4KB random read/write command rate (IOPs)
48,000/
22,000
48,000/
16,000
48,000/
8000
Sustainable 4KB Random combined IOPS for 5 year Endurance
(65%/35% R/W, 70% Duty Cycle)
[3]
31,000
31,000
31,000
[1] Testing performed at Queue Depth = 32, Sequentially Preconditioned drive, using IOMeter 2006.7.27.
[2] Testing performed at Queue Depth = 32, Randomly Preconditioned drive, using IOMeter 2006.7.27.
[3] Testing performed at Queue Depth = 32, Non-Preconditioned drive, using IOMeter 2006.7.27.
IOMeter is licensed under the Intel Open Source License and the GNU General Public License. Intel
does not endorse any IOMeter results.
Peak performance is defined as the typical best case performance that the product will be able to
achieve when the product is preconditioned as mentioned and host commands are aligned on 4KB
boundaries.
Sustained performance is defined as the typical worst case performance that the product will be able to
achieve when the product is preconditioned as mentioned and host commands are aligned on 4KB boundar-
ies. Write values also take into account the worst case performance throttling that may occur to ensure the
product meets specified reliability specifications.
12
Pulsar XT.2 SAS Product Manual, Rev. B
Due to the nature of Flash memory technologies there are many factors that can result in values different than
those stated in this specification. Some discrepancies can be caused by bandwidth limitations in the host
adapter, operating system, or driver limitations. It is not the intent of this manual to cover all possible causes of
performance discrepancies.
When evaluating performance of SSD devices, it is recommended to measure performance of the device in a
method that resembles the targeted application using real world data and workloads. Test time should also be
adequately large to ensure that sustainable metrics and measures are obtained.
5.3
Start/stop time
The drive accepts the commands listed in the SAS Interface Manual less than 3 seconds after DC power has
been applied.
If the drive receives a NOTIFY (ENABLE SPINUP) primitive through either port and has not received a START
STOP UNIT command with the START bit equal to 0, the drive becomes ready for normal operations within 13
seconds (excluding the error recovery procedure).
If the drive receives a START STOP UNIT command with the START bit equal to 0 before receiving a NOTIFY
(ENABLE SPINUP) primitive, the drive waits for a START STOP UNIT command with the START bit equal to 1.
After receiving a START STOP UNIT command with the START bit equal to 1, the drive waits for a NOTIFY
(ENABLE SPINUP) primitive. After receiving a NOTIFY (ENABLE SPINUP) primitive through either port, the
drive becomes ready for normal operations within 13 seconds (excluding the error recovery procedure).
If the drive receives a START STOP UNIT command with the START bit and IMMED bit equal to 1 and does
not receive a NOTIFY (ENABLE SPINUP) primitive within 5 seconds, the drive fails the START STOP UNIT
command.
The START STOP UNIT command may be used to command the drive to stop. Stop time is 3 seconds (maxi-
mum) from removal of DC power. SCSI stop time is 3 seconds. There is no power control switch on the drive.
5.4
Cache control
All default cache mode parameter values (Mode Page 08h) for standard OEM versions of this drive family are
5.4.1
Caching write data
Write caching is a write operation by the drive that makes use of a drive buffer storage area where the data to
be written to the medium is stored while the drive performs the WRITE command.
If the number of write data logical blocks exceed the size of the segment being written into, when the end of the
segment is reached, the data is written into the beginning of the same cache segment, overwriting the data that
was written there at the beginning of the operation; however, the drive does not overwrite data that has not yet
been written to the medium.
If write caching is enabled (WCE=1), then the drive may return Good status on a WRITE command after the
data has been transferred into the cache, but before the data has been written to the medium. If an error
occurs while writing the data to the medium, and Good status has already been returned, a deferred error will
be generated.
Data that has not been written to the medium is protected by a back up power source which provides the ability
of the data to be written to non-volatile medium in the event of an unexpected power loss.
The SYNCHRONIZE CACHE command may be used to force the drive to write all cached write data to the
medium. Upon completion of a SYNCHRONIZE CACHE command, all data received from previous WRITE
commands will have been written to the medium. Tables 16, 17 and 18 show the mode default settings for the
drive.
Pulsar XT.2 SAS Product Manual, Rev. B
13
6.0
Reliability specifications
The following reliability specifications assume correct host and drive operational interface, including all inter-
face timings, power supply voltages, environmental requirements and drive mounting constraints.
1
Read Error Rates
Unrecovered Data
Miscorrected Data
Less than 1 LBA in 1016 bits transferred
Less than 1 LBA in 1021 bits transferred
Less than 1 error in 1012 bits transferred
2,000,000 hours
Interface error rate:
Mean Time Between Failure (MTBF):
Annualized Failure Rate (AFR):
Preventive maintenance:
0.44%
None required
Typical Data Retention with
3 months
2
Power removed (at 40C)
3
Endurance Rating:
Method 1: Full drive writes per day 35
Method 2: TBW (per JEDEC JESD218
400GB = 24,800 TB
200GB = 12,400 TB
100GB = 6,200 TB
1. Error rate specified with automatic retries and data correction with ECC enabled and all flaws reallocated.
2. As NAND Flash devices age with use, the capability of the media to retain a programmed value begins to deteriorate.
This deterioration is affected by the number of times a particular memory cell is programmed and subsequently erased.
When a device is new, it has a powered off data retention capability of up to several years. With use the retention ca-
pability of the device is reduced. Temperature also has an effect on how long a Flash component can retain its pro-
grammed value with power removed. At high temperature the retention capabilities of the device are reduced. Data
retention is not an issue with power applied to the SSD. The SSD drive contains firmware and hardware features that
can monitor and refresh memory cells when power is applied.
3. Endurance rating is the expected amount of host data that can be written by product when subjected to a specified work-
load at a specified operating and storage temperature. For the specific workload to achieve this level of endurance,
please reference JEDEC Specification JESD218. TBW is defined as 1x10^12 Bytes.
6.1
Error rates
The error rates stated in this manual assume the following:
• The drive is operated in accordance with this manual using DC power as defined in paragraph 7.3, "DC
• Errors caused by host system failures are excluded from error rate computations.
• Assume random data.
• Default OEM error recovery settings are applied. This includes AWRE, ARRE, full read retries, full write
retries and full retry time.
14
Pulsar XT.2 SAS Product Manual, Rev. B
6.1.1
Unrecoverable Errors
An unrecoverable data error is defined as a failure of the drive to recover data from the media. These errors
occur due to read or write problems. Unrecoverable data errors are only detected during read operations, but
not caused by the read. If an unrecoverable data error is detected, a MEDIUM ERROR (03h) in the Sense Key
will be reported. Multiple unrecoverable data errors resulting from the same cause are treated as 1 error.
6.1.2
Interface errors
An interface error is defined as a failure of the receiver on a port to recover the data as transmitted by the
device port connected to the receiver. The error may be detected as a running disparity error, illegal code, loss
of word sync, or CRC error.
6.2
Endurance Management
Customer satisfaction with Solid State Drives can be directly related to the internal algorithms which an SSD
uses to manage the limited number of Program-Erase (PE) cycles that NAND Flash can withstand. These
algorithms consist of Wearleveling, Garbage Collection, Write Amplification, Unmap, Data Retention, Lifetime
Endurance Management.
6.2.1
Wear Leveling
Wear Leveling is a technique used by the drive to ensure that all Flash cells are written to or exercised as
evenly as possible to avoid any hot spots where some cells are used up faster than other locations. Wear Lev-
eling is automatically managed by the drive and requires no user interaction. The Seagate algorithm is tuned to
operate only when needed to ensure reliable product operation.
6.2.2
Garbage Collection
Garbage Collection is a technique used by the drive to consolidate valid user data into a common cell range
freeing up unused or obsolete locations to be erased and used for future storage needs. Garbage Collection is
automatically managed by the drive and requires no user interaction. The Seagate algorithm is tuned to oper-
ate only when needed to ensure reliable product operation.
6.2.3
Write Amplification
While Write Amplification is not an algorithm, it is a major characteristic of SSD's that must be accounted for by
all the algorithms that the SSD implements. The Write Amplification Factor of an SSD is defined as the ratio of
Host/User data requested to be written to the actual amount of data written by the SSD internal to account for
the user data and the housekeeping activities such as Wear Leveling and Garbage Collection. The Write
Amplification Factor of an SSD can also be directly affected by the characteristics of the host data being sent to
the SSD to write. The best Write Amplification Factor is achieved for data that is written in sequential LBA's that
are aligned on 4KB boundaries. The worst case Write Amplification Factor typically occurs for randomly written
LBA's of transfer sizes that are less than 4KB and that originate on LBA's that are not on 4KB boundaries.
6.2.4
UNMAP
A new SCSI command has been added to the SSD as part of the Thin Provisioning feature set. Use of the
UNMAP command reduces the Write Amplification Factor of the drive during housekeeping tasks such as
Wear Leveling and Garbage Collection. This is accomplished because the drive does not need to retain data
which has been classified by the host as obsolete.
Pulsar XT.2 SAS Product Manual, Rev. B
15
6.2.5
Data Retention
Data Retention is another major characteristic of SSD's that must be accounted for by all the algorithms that
the SSD implements. While powered up, the Data Retention of SSD cells are monitored and rewritten if the cell
levels decay to an unexpected level. Data Retention when the drive is powered off is affected by Program and
Erase (PE) cycles and the temperature of the drive when stored.
6.2.6
Lifetime Endurance Management
As stated in Section 6.2, an SSD has a limited number of Program and Erase (PE) cycles that are capable. In
worse case applications, the write workload could be such that the drive experiences a high Write Amplification
Factor that could lead to potential wear out prior to the drive achieving it's expected field life. Additionally, the
Data Retention spec of the SSD needs to be considered to ensure the spec is met once the drive is worn out.
Seagate has implemented a Lifetime Endurance Management technique which helps OEMS and user to avoid
early wear out. By monitoring the write workload being sent to the drive, the drive can add additional response
time to WRITE commands to provide a sustainable level of performance that is capable of being sustained for
the life of the drive. Most users may never see this added response time in their applications.
6.3
Reliability and service
Integrators can enhance the reliability of Pulsar XT.2 drives by ensuring that the drive receives adequate cool-
ing. Section 7.0 provides temperature measurements and other information that may be used to enhance the
6.3.1
Annualized Failure Rate (AFR) and Mean Time Between Failure (MTBF)
The production drive shall achieve an AFR of 0.44% (MTBF of 2,000,000 hours) when operated in an environ-
ment that ensures the case temperatures do not exceed the values specified in Section 7.5. Operation at case
temperatures outside the specifications in Section 7.5 may increase the product AFR (decrease the MTBF).
The AFR (MTBF) is a population statistic not relevant to individual units.
The AFR (MTBF) specification is based on the following assumptions for Enterprise Storage System environ-
ments:
• 8760 power-on hours per year.
• 250 average on/off cycles per year.
• Operations at nominal voltages.
• Systems will provide adequate cooling to ensure the case temperatures specified in Section 7.5 are not
decrease the MTBF.
6.3.2
Preventive maintenance
No routine scheduled preventive maintenance is required.
6.3.3
Hot plugging the drive
When a drive is powered on by switching the power or hot plugged, the drive runs a self test before attempting
to communicate on its’ interfaces. When the self test completes successfully, the drive initiates a Link Reset
starting with OOB. An attached device should respond to the link reset. If the link reset attempt fails, or any
time the drive looses sync, the drive initiated link reset. The drive will initiate link reset once per second but
alternates between port A and B. Therefore each port will attempt a link reset once per 2 seconds assuming
both ports are out of sync.
If the self-test fails, the drive does not respond to link reset on the failing port.
Note. It is the responsibility of the systems integrator to assure that no temperature, energy, voltage haz-
ard, or ESD potential hazard is presented during the hot connect/disconnect operation. Discharge
16
Pulsar XT.2 SAS Product Manual, Rev. B
the static electricity from the drive carrier prior to inserting it into the system.
6.3.4
S.M.A.R.T.
S.M.A.R.T. is an acronym for Self-Monitoring Analysis and Reporting Technology. This technology is intended
to recognize conditions that indicate imminent drive failure and is designed to provide sufficient warning of a
failure to allow administrators to back up the data before an actual failure occurs.
Note. The drive’s firmware monitors specific attributes for degradation over time but can’t predict instanta-
neous drive failures.
Each monitored attribute has been selected to monitor a specific set of failure conditions in the operating per-
formance of the drive and the thresholds are optimized to minimize “false” and “failed” predictions.
Controlling S.M.A.R.T.
The operating mode of S.M.A.R.T. is controlled by the DEXCPT and PERF bits on the Informational Exceptions
Control mode page (1Ch). Use the DEXCPT bit to enable or disable the S.M.A.R.T. feature. Setting the DEX-
CPT bit disables all S.M.A.R.T. functions. When enabled, S.M.A.R.T. collects on-line data as the drive performs
normal read and write operations. When the PERF bit is set, the drive is considered to be in “On-line Mode
Only” and will not perform off-line functions.
An application can measure off-line attributes and force the drive to save the data by using the REZERO UNIT
command. Forcing S.M.A.R.T. resets the timer so that the next scheduled interrupt is in one hour.
An application can interrogate the drive through the host to determine the time remaining before the next
scheduled measurement and data logging process occurs. To accomplish this, issue a LOG SENSE command
to log page 0x3E. This allows applications to control when S.M.A.R.T. interruptions occur. Forcing S.M.A.R.T.
with the REZERO UNIT command resets the timer.
Performance impact
S.M.A.R.T. attribute data is saved to the media so that the events that caused a predictive failure can be recre-
ated. The drive measures and saves parameters once every hour subject to an idle period on the drive inter-
faces. The process of measuring off-line attribute data and saving data to the media is interruptible. The
maximum on-line only processing delay is summarized below
Maximum processing delay
Fully-enabled delay
DEXCPT = 0
S.M.A.R.T. delay times
75 ms
Reporting control
Reporting is controlled by the MRIE bits in the Informational Exceptions Control mode page (1Ch). Subject to
the reporting method. For example, if the MRIE is set to one, the firmware will issue to the host an 01-5D00
sense code. The FRU field contains the type of predictive failure that occurred. The error code is preserved
through bus resets and power cycles.
Determining rate
S.M.A.R.T. monitors the rate at which errors occur and signals a predictive failure if the rate of degraded errors
increases to an unacceptable level. To determine rate, error events are logged and compared to the number of
total operations for a given attribute. The interval defines the number of operations over which to measure the
rate. The counter that keeps track of the current number of operations is referred to as the Interval Counter.
S.M.A.R.T. measures error rates. All errors for each monitored attribute are recorded. A counter keeps track of
the number of errors for the current interval. This counter is referred to as the Failure Counter.
Pulsar XT.2 SAS Product Manual, Rev. B
17
Error rate is the number of errors per operation. The algorithm that S.M.A.R.T. uses to record rates of error is to
set thresholds for the number of errors and appropriate interval. If the number of errors exceeds the threshold
before the interval expires, the error rate is considered to be unacceptable. If the number of errors does not
exceed the threshold before the interval expires, the error rate is considered to be acceptable. In either case,
the interval and failure counters are reset and the process starts over.
Predictive failures
S.M.A.R.T. signals predictive failures when the drive is performing unacceptably for a period of time. The firm-
ware keeps a running count of the number of times the error rate for each attribute is unacceptable. To accom-
plish this, a counter is incremented each time the error rate is unacceptable and decremented (not to exceed
zero) whenever the error rate is acceptable. If the counter continually increments such that it reaches the pre-
dictive threshold, a predictive failure is signaled. This counter is referred to as the Failure History Counter.
There is a separate Failure History Counter for each attribute.
6.3.5
Thermal monitor
Pulsar XT.2 drives implement a temperature warning system which:
1. Signals the host if the temperature exceeds a value which would threaten the drive.
2. Signals the host if the temperature exceeds a user-specified value. (i.e., the reference temperature value)
3. Saves a S.M.A.R.T. data frame on the drive which exceeds the threatening temperature value.
A temperature sensor monitors the drive temperature and issues a warning over the interface when the tem-
perature exceeds a set threshold. The temperature is measured at power-up and then at ten-minute intervals
after power-up.
The thermal monitor system generates a warning code of 01-0B01 when the temperature exceeds the speci-
fied limit in compliance with the SCSI standard. The drive temperature is reported in the FRU code field of
MODE SENSE data. Administrators can use this information to determine if the warning is due to the tempera-
ture exceeding the drive threatening temperature or the user-specified temperature.
This feature is controlled by the Enable Warning (EWasc) bit, and the reporting mechanism is controlled by the
Method of Reporting Informational Exceptions field (MRIE) on the Informational Exceptions Control (IEC)
mode page (1Ch).
The current algorithm implements two temperature trip points. The first trip point is set at the maximum temper-
ature limit according to the drive specification. The second trip point is user-selectable using the LOG SELECT
command. The reference temperature parameter in the temperature log page (see Table 7) can be used to set
this trip point. The default value for this drive is listed in the table, however, applications can set it to any value
in the range defined. If a temperature is specified that is greater than the maximum allowed in this field, the
temperature is rounded down to the maximum allowed. A sense code is sent to the host to indicate the round-
ing of the parameter field.
Table 7:
Temperature Log Page (0Dh)
Parameter Code
Description
400GB
200/100GB
Primary Temperature
Drive Temperature
0000h
Default Setting
70°C
0 to 70°C
65°C
0 to 65°C
Reference Temperature
0001h
Changeable Range
18
Pulsar XT.2 SAS Product Manual, Rev. B
6.3.6
Drive Self Test (DST)
Drive Self Test (DST) is a technology designed to recognize drive fault conditions that qualify the drive as a
failed unit. DST validates the functionality of the drive at a system level.
There are two test coverage options implemented in DST:
1. Extended test
2. Short test
The most thorough option is the extended test that performs various tests on the drive and scans every logical
block address (LBA) of the drive. The short test is time-restricted and limited in length—it does not scan the
entire media contents, but does some fundamental tests and scans portions of the media.
If DST encounters an error during either of these tests, it reports a "diagnostic failed" condition. If the drive fails
the test, remove it from service and return it to Seagate for service.
6.3.6.1
DST failure definition
The drive will present a “diagnostic failed” condition through the self-tests results value of the diagnostic log
page if a functional failure is encountered during DST. The drive parameters are not modified to test the drive
more stringently, and the recovery capabilities are not reduced. All retries and recovery processes are enabled
during the test. If data is recoverable, no failure condition will be reported regardless of the recovery processes
required to recover the data.
The following conditions are considered DST failure conditions:
• Read error after recovery attempts are exhausted
• Write error after recovery attempts are exhausted
Recovered errors will not be reported as diagnostic failures.
6.3.6.2
Implementation
This section provides all of the information necessary to implement the DST function on this drive.
6.3.6.2.1
State of the drive prior to testing
The drive must be in a ready state before issuing the SEND DIAGNOSTIC command. There are multiple rea-
sons why a drive may not be ready, some of which are valid conditions, and not errors. For example, a drive
may be in process of doing a FORMAT UNIT, or another DST. It is the responsibility of the host application to
determine the “not ready” cause.
6.3.6.2.2
Invoking DST
To invoke DST, submit the SEND DIAGNOSTIC command with the appropriate Function Code (001b for the
short test or 010b for the extended test) in bytes 1, bits 5, 6, and 7.
Pulsar XT.2 SAS Product Manual, Rev. B
19
6.3.6.2.3
Short and extended tests
DST has two testing options:
1. short
2. extended
These testing options are described in the following two subsections.
Each test consists of two segments: an electrical test segment and a read/verify scan segment.
Short test (Function Code: 001b)
The purpose of the short test is to provide a time-limited test that tests as much of the drive as possible within
120 seconds. The short test does not scan the entire media contents, but does some fundamental tests and
scans portions of the media. A complete read/verify scan is not performed and only factual failures will report a
"diagnostic failed" condition. This option provides a quick confidence test of the drive.
Extended test (Function Code: 010b)
The objective of the extended test option is to empirically test critical drive components. The read operation
tests the media contents. The integrity of the media is checked through a read/verify scan of the media.
The anticipated length of the Extended test is reported through the Control Mode page.
6.3.6.2.4
Log page entries
When the drive begins DST, it creates a new entry in the Self-test Results Log page. The new entry is created
by inserting a new self-test parameter block at the beginning of the self-test results log parameter section of the
log page. Existing data will be moved to make room for the new parameter block. The drive reports 20 param-
eter blocks in the log page. If there are more than 20 parameter blocks, the least recent parameter block will be
deleted. The new parameter block will be initialized as follows:
1. The Function Code field is set to the same value as sent in the DST command
2. The Self-Test Results Value field is set to Fh
3. The drive will store the log page to non-volatile memory
After a self-test is complete or has been aborted, the drive updates the Self-Test Results Value field in its Self-
Test Results Log page in non-volatile memory. The host may use LOG SENSE to read the results from up to
the last 20 self-tests performed by the drive. The self-test results value is a 4-bit field that reports the results of
the test. If the field is set to zero, the drive passed with no errors detected by the DST. If the field is not set to
zero, the test failed for the reason reported in the field.
The drive will report the failure condition and LBA (if applicable) in the Self-test Results Log parameter. The
Sense key, ASC, ASCQ, and FRU are used to report the failure condition.
6.3.6.2.5
Abort
There are several ways to abort a diagnostic. Applications can use a SCSI Bus Reset or a Bus Device Reset
message to abort the diagnostic.
Applications can abort a DST executing in background mode by using the abort code in the DST Function
Code field. This will cause a 01 (self-test aborted by the application client) code to appear in the self-test
results values log. All other abort mechanisms will be reported as a 02 (self-test routine was interrupted by a
reset condition).
20
Pulsar XT.2 SAS Product Manual, Rev. B
6.3.7
Product warranty
Beginning on the date of shipment to the customer and continuing for the period specified in the purchase con-
tract, Seagate warrants that each product (including components and subassemblies) that fails to function
properly under normal use due to defect in materials or workmanship or due to nonconformance to the applica-
ble specifications will be repaired or replaced, at Seagate’s option and at no charge to the customer, if returned
by customer at customer’s expense to Seagate’s designated facility in accordance with Seagate’s warranty
procedure. Seagate will pay for transporting the repair or replacement item to the customer. For more detailed
warranty information, refer to the standard terms and conditions of purchase for Seagate products stated in
purchase documentation.
The remaining warranty for a particular drive can be determined by calling Seagate Customer Service at
1-800-468-3472. Customers can also determine remaining warranty using the Seagate web site (www.sea-
gate.com). The drive serial number is required to determine remaining warranty information.
Shipping
When transporting or shipping a drive, use only a Seagate-approved container. Keep the original box. Seagate
approved containers are easily identified by the Seagate Approved Package label. Shipping a drive in a non-
approved container voids the drive warranty.
Seagate repair centers may refuse receipt of components improperly packaged or obviously damaged in tran-
sit. Contact your authorized Seagate distributor to purchase additional boxes. Seagate recommends shipping
by an air-ride carrier experienced in handling computer equipment.
Product repair and return information
Seagate customer service centers are the only facilities authorized to service Seagate drives. Seagate does
not sanction any third-party repair facilities. Any unauthorized repair or tampering with the factory seal voids
the warranty.
Storage
The maximum recommended storage period for the drive in a non-operational environment is 90 days. Drives
should be stored in the original unopened Seagate shipping packaging when ever possible. Once the drive is
removed from the Seagate original packaging the recommended maximum period between drive operation
cycles is 30 days. During any storage period the drive non-operational temperature, humidity, wet bulb, atmo-
spheric conditions, shock, vibration, magnetic and electrical field specifications should be followed.
(see Section 7.0)
Pulsar XT.2 SAS Product Manual, Rev. B
21
7.0
Physical/electrical specifications
This section provides information relating to the physical and electrical characteristics of the drive.
7.1
Power specifications
The drive receives DC power (+5V and +12V) through the standard SAS interface.
7.1.1 Power consumption
Power requirements for the drives are listed in the tables beginning on page 23. Typical power measurements
are based on an average of drives tested, under nominal conditions, using +5V and +12V input voltage at 60°C
ambient temperature.
• Startup power
Startup power is measured from the time of power-on to the time that the drive reaches operating condition
and can process media access commands.
• Peak operating mode
During peak operating mode, the drive is tested in various read and write access patterns to simulate the
worst-case power consumption.
• Idle mode power
Idle mode power is measured with the drive powered up and ready for media access commands, with no
media access commands having been received from the host.
7.2
AC power requirements
None.
22
Pulsar XT.2 SAS Product Manual, Rev. B
7.3
DC power requirements
Table 8:
400GB standard model DC power requirements
Parameter
Regulation
Voltage
400GB (6.0Gb)
±5%
±5%
+5V
+12V
Current (A)
Current (A)
Power (W)
DC
Average idle current
Maximum starting current
(peak DC) DC
0.44
0.31
5.92
3σ
3σ
3σ
1.15
1.21
0.44
0.45
0.63
0.31
(peak AC) AC
Delayed start (max) DC
Peak operating current (random read):
Typical DC
5.92
DC
3σ
0.47
0.48
0.47
0.36
0.37
0.46
6.67
6.84
Maximum DC
Maximum (peak) DC
Peak operating current (random write)
Typical DC
3σ
DC
3σ
0.45
0.46
0.60
0.42
0.43
053
7.29
7.46
Maximum DC
Maximum (peak) DC
Peak operating current (sequential read)
Typical DC
3σ
DC
3σ
0.58
0.59
0.64
0.44
0.45
0.52
8.18
8.35
Maximum DC
Maximum (peak) DC
Peak operating current (sequential write)
Typical DC
3σ
DC
3σ
0.55
0.56
0.57
0.53
0.54
0.63
9.11
9.28
Maximum DC
Maximum (peak) DC
3σ
Pulsar XT.2 SAS Product Manual, Rev. B
23
Table 9:
200GB standard model DC power requirements
Parameter
Regulation
Voltage
200GB (6.0Gb)
±5%
±5%
+5V
+12V
Current (A)
Current (A)
Power (W)
DC
Average idle current
Maximum starting current
(peak DC) DC
0.40
0.17
4.04
3σ
3σ
3σ
1.13
1.20
0.43
0.30
0.64
0.19
(peak AC) AC
Delayed start (max) DC
Peak operating current (random read):
Typical DC
4.43
DC
3σ
0.47
0.50
0.77
0.22
0.22
0.55
4.99
5.14
Maximum DC
Maximum (peak) DC
Peak operating current (random write)
Typical DC
3σ
DC
3σ
0.45
0.49
0.71
0.27
0.28
0.74
5.49
5.81
Maximum DC
Maximum (peak) DC
Peak operating current (sequential read)
Typical DC
3σ
DC
3σ
0.54
0.58
0.79
0.27
0.28
0.55
5.94
6.26
Maximum DC
Maximum (peak) DC
Peak operating current (sequential write)
Typical DC
3σ
DC
3σ
0.52
0.56
0.79
0.35
0.36
0.85
6.80
7.12
Maximum DC
Maximum (peak) DC
3σ
24
Pulsar XT.2 SAS Product Manual, Rev. B
Table 10:
100GB standard model DC power requirements
Parameter
Regulation
Voltage
100GB (6.0Gb)
±5%
±5%
+5V
+12V
Current (A)
Current (A)
Power (W)
DC
Average idle current
Maximum starting current
(peak DC) DC
0.40
0.17
4.04
3σ
3σ
3σ
1.09
1.16
0.43
0.31
0.73
0.18
(peak AC) AC
Delayed start (max) DC
Peak operating current (random read):
Typical DC
4.31
DC
3σ
0.46
0.49
0.80
0.21
0.23
0.72
4.82
5.21
Maximum DC
Maximum (peak) DC
Peak operating current (random write)
Typical DC
3σ
DC
3σ
0.45
0.49
0.71
0.25
0.26
0.54
5.25
5.57
Maximum DC
Maximum (peak) DC
Peak operating current (sequential read)
Typical DC
3σ
DC
3σ
0.54
0.58
0.80
0.28
0.29
0.58
6.06
6.38
Maximum DC
Maximum (peak) DC
Peak operating current (sequential write)
Typical DC
3σ
DC
3σ
0.53
0.57
0.82
0.36
0.37
0.82
6.97
7.29
Maximum DC
Maximum (peak) DC
3σ
[1] Measured with average reading DC ammeter. Instantaneous +12V current peaks will exceed these values. Power
supply at nominal voltage. N (number of drives tested) = 6, 60 Degrees C ambient.
[2] For +12 V, a –10% tolerance is allowed during initial start but must return to ±5% before reaching ready state. The
±5% must be maintained after the drive signifies that its power-up sequence has been completed and that the drive is
able to accept selection by the host initiator.
[5] This condition occurs after OOB and Speed Negotiation completes but before the drive has received the Notify Spinup
primitive.
[6] See paragraph 7.3.1, "Conducted noise immunity." Specified voltage tolerance includes ripple, noise, and transient
response.
Pulsar XT.2 SAS Product Manual, Rev. B
25
General DC power requirement notes.
1. Minimum current loading for each supply voltage is not less than 1.7% of the maximum operating current
shown.
2. The +5V and +12V supplies should employ separate ground returns.
3. Where power is provided to multiple drives from a common supply, careful consideration for individual
drive power requirements should be noted. Where multiple units are powered on simultaneously, the peak
starting current must be available to each device.
4. Parameters, other than start, are measured after a 10-minute warm up.
7.3.1
Conducted noise immunity
Noise is specified as a periodic and random distribution of frequencies covering a defined frequency. Maximum
allowed noise values given below are peak-to-peak measurements and apply at the drive power connector.
+5v
=
=
250 mV pp from 100 Hz to 20 MHz.
+12v
450 mV pp from 100 Hz to 100 KHz.
250 mV pp from 100 KHz to 20 MHz.
150 mV pp from 20 MHz to 80 MHz.
7.3.2
Power sequencing
The drive does not require power sequencing. The drive protects against inadvertent writing during power-up
and down.
7.3.3
Current profiles
The +12V and +5V current profiles for the Pulsar 10K.4 drives are shown below.
Figure 1.
Current profiles for 400GB models
26
Pulsar XT.2 SAS Product Manual, Rev. B
7.4
Power dissipation
400GB models in 6Gb operation
Typical power dissipation under idle conditions in 6Gb operation is 5.92 watts 20.20 BTUs per hour).
To obtain operating power for typical random write operations, refer to the following I/O rate curve (see Figure
4). Locate the typical I/O rate for a drive in your system on the horizontal axis and read the corresponding +5
volt current, +12 volt current, and total watts on the vertical axis. To calculate BTUs per hour, multiply watts by
3.4123.
Figure 4.
400GB (at 6Gb) DC current and power vs. input/output operations per second
200GB models in 6Gb operation
Typical power dissipation under idle conditions in 6Gb operation is 4.04 watts (13.79 BTUs per hour).
To obtain operating power for typical random write operations, refer to the following I/O rate curve (see Figure
5). Locate the typical I/O rate for a drive in your system on the horizontal axis and read the corresponding +5
volt current, +12 volt current, and total watts on the vertical axis. To calculate BTUs per hour, multiply watts by
3.4123.
Figure 5.
200GB (at 6Gb) DC current and power vs. input/output operations per second
28
Pulsar XT.2 SAS Product Manual, Rev. B
100GB models in 6Gb operation
Typical power dissipation under idle conditions in 6Gb operation is 4.04 watts 13.79 BTUs per hour).
To obtain operating power for typical random write operations, refer to the following I/O rate curve (see Figure
6). Locate the typical I/O rate for a drive in your system on the horizontal axis and read the corresponding +5
volt current, +12 volt current, and total watts on the vertical axis. To calculate BTUs per hour, multiply watts by
3.4123.
Figure 6.
100GB (at 6Gb) DC current and power vs. input/output operations per second
7.5
Environmental limits
Temperature and humidity values experienced by the drive must be such that condensation does not occur on
any drive part. Altitude and atmospheric pressure specifications are referenced to a standard day at 58.7°F
(14.8°C). Maximum wet bulb temperature is 82°F (28°C).
Note. To maintain optimal performance drives should be run at nominal case temperatures.
7.5.1
Temperature
a. Operating
The drive meets the operating specifications over a 32°F to 140°F (0°C to 60°C) drive case temperature
range with a maximum temperature gradient of 36°F (20°C) per hour.
The maximum allowable drive case temperature is 60°C.
The MTBF specification for the drive assumes the operating environment is designed to maintain nominal
case temperature. The rated MTBF is based upon a sustained case temperature of 122°F (50°C). Occa-
sional excursions in operating temperature between the rated MTBF temperature and the maximum drive
operating case temperature may occur without impact to the rated MTBF temperature. However continual
or sustained operation at case temperatures beyond the rated MTBF temperature will degrade the drive
MTBF and reduce product reliability.
Air flow may be required to achieve consistent nominal case temperature values (see Section 7.5). To con-
firm that the required cooling is provided, place the drive in its final mechanical configuration, and perform
random write/read operations. After the temperatures stabilize, measure the case temperature of the drive.
Pulsar XT.2 SAS Product Manual, Rev. B
29
b. Non-operating
–40° to 158°F (–40° to 70°C) package ambient with a maximum gradient of 36°F (20°C) per hour. This
specification assumes that the drive is packaged in the shipping container designed by Seagate for use with
drive.
Figure 7.
Temperature check point location - 15mm drives
Figure 8.
Temperature check point location - 7mm drives
Note. Images may not represent actual product, for reference only.
7.5.2 Relative humidity
The values below assume that no condensation on the drive occurs.
a. Operating
5% to 95% non-condensing relative humidity with a maximum gradient of 20% per hour.
b. Non-operating
5% to 95% non-condensing relative humidity.
7.5.3
Effective altitude (sea level)
a. Operating
–200 to +10,000 feet (–60.96 to +3048 meters)
b. Non-operating
–200 to +40,000 feet (–60.96 to +12,192 meters)
7.5.4
Shock and vibration
Shock and vibration limits specified in this document are measured directly on the drive chassis. If the drive is
installed in an enclosure to which the stated shock and/or vibration criteria is applied, resonances may occur
internally to the enclosure resulting in drive movement in excess of the stated limits. If this situation is apparent,
it may be necessary to modify the enclosure to minimize drive movement.
The limits of shock and vibration defined within this document are specified with the drive mounted by any of
30
Pulsar XT.2 SAS Product Manual, Rev. B
7.5.4.1
Shock
a. Operating—normal
The drive, as installed for normal operation, shall operate error free while subjected to intermittent shock not
exceeding:
• 1000 Gs at a maximum duration of 0.5ms (half sinewave)
Shock may be applied in the X, Y, or Z axis. Shock is not to be repeated more than once every 2 seconds.
Note. This specification does not cover connection issues that may result from testing at this level.
b. Non-operating
The limits of non-operating shock shall apply to all conditions of handling and transportation. This includes
both isolated drives and integrated drives.
The drive subjected to nonrepetitive shock not exceeding the three values below, shall not exhibit device
damage or performance degradation.
• 1000 Gs at a maximum duration of 0.5ms (half sinewave)
Shock may be applied in the X, Y, or Z axis.
c. Packaged
Seagate finished drive bulk packs are designed and tested to meet or exceed applicable ISTA and ASTM
standards. Volume finished drives will be shipped from Seagate factories on pallets to minimize freight
costs and ease material handling. Seagate finished drive bulk packs may be shipped individually. For less
than full shipments, instructions are printed on the bulk pack carton for minimum drive quantities and proper
drive placement.
Figure 9.
Recommended mounting
Note. Image may not represent actual product, for reference only.
Pulsar XT.2 SAS Product Manual, Rev. B
31
7.5.4.2
Vibration
a. Operating—normal
The drive as installed for normal operation, shall comply with the complete specified performance while
subjected to vibration:
Vibration may be applied in the X, Y, or Z axis.
Operating normal translational random flat profile
20 - 2000 Hz (translational random flat profile)
16.3 GRMS
Note. This specification does not cover connection issues that may result from testing at this level.
b. Operating—abnormal
Equipment as installed for normal operation shall not incur physical damage while subjected to periodic
vibration:
Vibration occurring at these levels may degrade operational performance during the abnormal vibration
period. Specified operational performance will continue when normal operating vibration levels are
resumed. This assumes system recovery routines are available.
Operating abnormal translational random flat profile
20 - 2000 Hz (translational random flat profile)
16.3 GRMS
Note. This specification does not cover connection issues that may result from testing at this level.
c. Non-operating
The limits of non-operating vibration shall apply to all conditions of handling and transportation. This
includes both isolated drives and integrated drives.
The drive shall not incur physical damage or degraded performance as a result of vibration.
Vibration may be applied in the X, Y, or Z axis.
Non-operating translational random flat profile
20 - 2000 Hz (translational random flat profile)
16.3 GRMS
7.5.5
Air cleanliness
The drive is designed to operate in a typical office environment with minimal environmental control.
7.5.6
Corrosive environment
Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure to
light industrial environments containing sulfurous gases, chlorine and nitric oxide, classes G and H per ASTM
B845. However, this accelerated testing cannot duplicate every potential application environment.
Users should use caution exposing any electronic components to uncontrolled chemical pollutants and corro-
sive chemicals as electronic drive component reliability can be affected by the installation environment. The sil-
ver, copper, nickel and gold films used in Seagate products are especially sensitive to the presence of sulfide,
chloride, and nitrate contaminants. Sulfur is found to be the most damaging. In addition, electronic components
should never be exposed to condensing water on the surface of the printed circuit board assembly (PCBA) or
exposed to an ambient relative humidity greater than 95%. Materials used in cabinet fabrication, such as vulca-
nized rubber, that can outgas corrosive compounds should be minimized or eliminated. The useful life of any
electronic equipment may be extended by replacing materials near circuitry with sulfide-free alternatives.
7.5.7
Electromagnetic susceptibility
See Section 3.1.1.1.
32
Pulsar XT.2 SAS Product Manual, Rev. B
7.6
Mechanical specifications
Refer to Figure 10 or 11 for detailed mounting configuration dimensions. See Section 10.3, “Drive mounting.”
Weight: 0.441 pounds 200 grams
Note. These dimensions conform to the Small Form Factor Standard documented in SFF-8201 and
Figure 10. Mounting configuration dimensions (400GB models)
Pulsar XT.2 SAS Product Manual, Rev. B
33
8.0
About self-encrypting drives
Self-encrypting drives (SEDs) offer encryption and security services for the protection of stored data, com-
monly known as “protection of data at rest.” These drives are compliant with the Trusted Computing Group
(TCG) Enterprise Storage Specifications as detailed in Section 3.2.
The Trusted Computing Group (TCG) is an organization sponsored and operated by companies in the com-
puter, storage and digital communications industry. Seagate’s SED models comply with the standards pub-
lished by the TCG.
To use the security features in the drive, the host must be capable of constructing and issuing the following two
SCSI commands:
• SECURITY PROTOCOL OUT
• SECURITY PROTOCOL IN
These commands are used to convey the TCG protocol to and from the drive in the appropriate command pay-
loads.
8.1
Data encryption
Encrypting drives use one in-line encryption engine for each port, employing AES-256 data encryption in
Cipher Block Chaining (CBC) mode to encrypt all data prior to being written on the media and to decrypt all
data as it is read from the media. The encryption engines are always in operation, cannot be disabled, and do
not detract in any way from the performance of the drive.
The 32-byte Data Encryption Key (DEK) is a random number which is generated by the drive, never leaves the
drive, and is inaccessible to the host system. The DEK is itself encrypted when it is stored on the media and
when it is in volatile temporary storage (DRAM) external to the encryption engine. A unique data encryption
8.2
Controlled access
The drive has two security partitions (SPs) called the "Admin SP" and the "Locking SP." These act as gate-
keepers to the drive security services. Security-related commands will not be accepted unless they also supply
the correct credentials to prove the requester is authorized to perform the command.
8.2.1
Admin SP
The Admin SP allows the drive's owner to enable or disable firmware download operations (see Section 8.4).
Access to the Admin SP is available using the SID (Secure ID) password or the MSID (Makers Secure ID)
password.
Pulsar XT.2 SAS Product Manual, Rev. B
35
8.2.2
Locking SP
The Locking SP controls read/write access to the media and the cryptographic erase feature. Access to the
Locking SP is available using the BandMasterX or EraseMaster passwords. Since the drive owner can define
up to 16 data bands on the drive, each data band has its own password called BandMasterX where X is the
number of the data band (0 through 15).
8.2.3
Default password
When the drive is shipped from the factory, all passwords are set to the value of MSID. This 32-byte random
value is printed on the drive label and it can be read by the host electronically over the I/O. After receipt of the
drive, it is the responsibility of the owner to use the default MSID password as the authority to change all other
passwords to unique owner-specified values.
8.3
Random number generator (RNG)
The drive has a 32-byte hardware RNG that it is uses to derive encryption keys or, if requested to do so, to pro-
vide random numbers to the host for system use, including using these numbers as Authentication Keys (pass-
words) for the drive’s Admin and Locking SPs.
8.4
Drive locking
In addition to changing the passwords, as described in Section 8.2.3, the owner should also set the data
access controls for the individual bands.
The variable "LockOnReset" should be set to "PowerCycle" to ensure that the data bands will be locked if
power is lost. This scenario occurs if the drive is removed from its cabinet. The drive will not honor any data
READ or WRITE requests until the bands have been unlocked. This prevents the user data from being
accessed without the appropriate credentials when the drive has been removed from its cabinet and installed
in another system.
When the drive is shipped from the factory, the firmware download port is unlocked allowing the drive to accept
any attempt to download new firmware. The drive owner must use the SID credential to lock the firmware
download port before firmware updates will be rejected.
8.5
Data bands
When shipped from the factory, the drive is configured with a single data band called Band 0 (also known as
the Global Data Band) which comprises LBA 0 through LBA max. The host may allocate Band1 by specifying a
start LBA and an LBA range. The real estate for this band is taken from the Global Band. An additional 14 Data
Bands may be defined in a similar way (Band2 through Band15) but before these bands can be allocated LBA
space, they must first be individually enabled using the EraseMaster password.
Data bands cannot overlap but they can be sequential with one band ending at LBA (x) and the next beginning
at LBA (x+1).
Each data band has its own drive-generated encryption key and its own user-supplied password. The host may
change the Encryption Key (see Section 8.6) or the password when required. The bands shall be aligned to
4KB LBA boundaries.
36
Pulsar XT.2 SAS Product Manual, Rev. B
8.6
Cryptographic erase
A significant feature of SEDs is the ability to perform a cryptographic erase. This involves the host telling the
drive to change the data encryption key for a particular band. Once changed, the data is no longer recoverable
since it was written with one key and will be read using a different key. Since the drive overwrites the old key
with the new one, and keeps no history of key changes, the user data can never be recovered. This is tanta-
mount to an instantaneous data erase and is very useful if the drive is to be scrapped or redispositioned.
8.7
Authenticated firmware download
In addition to providing a locking mechanism to prevent unwanted firmware download attempts, the drive also
only accepts download files which have been cryptographically signed by the appropriate Seagate Design
Center.
Three conditions must be met before the drive will allow the download operation:
1. The download must be an SED file. A standard (base) drive (non-SED) file will be rejected.
2. The download file must be signed and authenticated.
3. As with a non-SED drive, the download file must pass the acceptance criteria for the drive. For example it
must be applicable to the correct drive model, and have compatible revision and customer status.
8.8
Power requirements
The standard drive models and the SED drive models have identical hardware, however the security and
encryption portion of the drive controller ASIC is enabled and functional in the SED models. This represents a
small additional drain on the 5V supply of about 30mA and a commensurate increase of about 150mW in
power consumption. There is no additional drain on the 12V supply. See the tables in Section 7.3 for power
requirements on the standard (non-SED) drive models.
8.9
Supported commands
The SED models support the following two commands in addition to the commands supported by the standard
(non-SED) models as listed in Table 14:
• SECURITY PROTOCOL OUT (B5h)
• SECURITY PROTOCOL IN (A2h)
8.10
RevertSP
The SED models will support RevertSP feature where it erases all data in all bands on the device and returns
the contents of all SPs (Security Providers) on the device to their Original Factory State.
Pulsar XT.2 SAS Product Manual, Rev. B
37
9.0
Defect and error management
Seagate continues to use innovative technologies to manage defects and errors. These technologies are
designed to increase data integrity, perform drive self-maintenance, and validate proper drive operation.
SCSI defect and error management involves drive internal defect/error management and SAS system error
considerations (errors in communications between the initiator and the drive). In addition, Seagate provides
the following technologies used to increase data integrity and drive reliability:
The read error rates and specified storage capacities are not dependent on host (initiator) defect management
routines.
9.1
Drive internal defects/errors
During the initial drive manufacturing test operation at the factory, media defects are identified, tagged as being
unusable, and their locations recorded on the drive primary defects list (referred to as the “P’ list). At factory
format time, these known defects are also deallocated, that is, marked as retired and the location listed in the
defects reallocation table. The “P” list is not altered after factory formatting. Locations of defects found and
reallocated during error recovery procedures after drive shipment are listed in the “G” list (defects growth list).
The “P” and “G” lists may be referenced by the initiator using the READ DEFECT DATA command.
Details of the SCSI commands supported by the drive are described in the SAS Interface Manual. Also, more
information on the drive Error Recovery philosophy is presented in the SAS Interface Manual.
The drive uses a vendor unique format to report defects via the READ DEFECT DATA command pending T10
standardization of a format for Solid State Devices. This format defect type is defined as 110b in the SCSI
FORMAT UNIT command. The definition of the 110b format is defined in the following table.
Table 11:
Bit
Byte
SSD Physical format address descriptor
7
6
5
4
3
2
1
0
0
1
2
3
4
5
6
7
(MSB)
MEDIA ID
(LSB)
CHANNEL
DIE
(MSB)
BLOCK
(LSB)
RESERVED
VENDOR UNIQUE
The MEDIA ID field contains an identifier for the flash controller for devices that utilize more than one flash
controller.
The CHANNEL field contains the channel number within the corresponding Flash Controller.
38
Pulsar XT.2 SAS Product Manual, Rev. B
The DIE field contains the die number within channel.
The BLOCK field contains the block number within the die.
The VENDOR UNIQUE field may contain vendor unique information.
9.2
Drive error recovery procedures
When an error occurs during drive operation, the drive performs error recovery procedures to attempt to
recover the data. The error recovery procedures used are not user changeable.
9.3
SAS system errors
Information on the reporting of operational errors across the interface is given in the SAS Interface Manual.
The SSP Response returns information to the host about numerous kinds of errors. The Receive Diagnostic
Results reports the results of diagnostic operations performed by the drive.
Status returned by the drive to the initiator is described in the SAS Interface Manual. Status reporting plays a
role in systems error management and its use in that respect is described in sections where the various com-
mands are discussed.
9.4
Background Media Scan
Background Media Scan (BMS) is a self-initiated media scan. BMS is defined in the T10 document SPC-4
available from the T10 committee. BMS performs reads across the entire addressable space of the media
while the drive is idle. In RAID arrays, BMS allows hot spare drives to be scanned for defects prior to being put
into service by the host system. On regular duty drives, if the host system makes use of the BMS Log Page, it
can avoid placing data in suspect locations on the media. Unreadable and recovered error sites will be logged
and reallocated.
With BMS, the host system can consume less power and system overhead by only checking BMS status and
results rather than tying up the bus and consuming power in the process of host-initiated media scanning activ-
ity.
Since the background scan functions are only done during idle periods, BMS causes a negligible impact to sys-
tem performance. The BMS scan is performed after 500ms of idle time. Other features that normally use idle
time to function will function normally because BMS functions for bursts of 500ms and then suspends activity
for 100ms to allow other background functions to operate.
BMS interrupts immediately to service host commands from the interface bus while performing reads. BMS will
complete any BMS-initiated error recovery prior to returning to service host-initiated commands. Overhead
associated with a return to host-servicing activity from BMS only impacts the first command that interrupted
BMS, this results in a typical delay of about 1ms.
9.5
Auto-Reallocation
Auto-Reallocation allows the drive to reallocate unreadable locations on a subsequent write command if the
recovery process deems the location to be defective. The drive performs auto-reallocation on every WRITE
command. With each write to a Logical LBA, the drive writes the data to a different physical media location.
Physical locations that return unrecoverable errors are retired during future WRITE attempts and associated
recovery process.
This is in contrast to the system having to use the REASSIGN BLOCKS command to reassign a location that
was unreadable and then generate a WRITE command to rewrite the data. This operation requires that AWRE
and ARRE are enabled—this is the default setting from the Seagate factory.
Pulsar XT.2 SAS Product Manual, Rev. B
39
9.6
Protection Information (PI)
Protection Information is intended as a standardized approach to system level LRC traditionally provided by
systems using 520 byte formatted LBAs. Drives formatted with PI information provide the same, common LBA
count (i.e. same capacity point) as non-PI formatted drives. Sequential performance of a PI drive will be
reduced by approximately 1.56% due to the extra overhead of PI being transferred from the media that is not
calculated as part of the data transferred to the host. To determine the full transfer rate of a PI drive, transfers
should be calculated by adding the 8 extra bytes of PI to the transferred LBA length, i.e. 512 + 8 = 520. PI for-
matted drives are physically formatted to 520 byte LBA’s that store 512 bytes of customer data with 8 bytes of
Protection Information appended to it. The advantage of PI is that the Protection Information bits can be man-
aged at the HBA and HBA driver level. Allowing a system that typically does not support 520 LBA formats to
integrate this level of protection.
Protection Information is valid with any supported LBA size. 512 LBA size is used here as common example.
9.6.1
Levels of PI
There are 4 types of Protection Information.
Type 0 - Describes a drive that is not formatted with PI information bytes. This allows for legacy support in non-
PI systems.
Type 1 - Provides support of PI protection using 10 and 16 byte commands. The RDPROTECT and WRTPRO-
TECT bits allow for checking control through the CDB. Eight bytes of Protection Information are transmitted at
LBA boundaries across the interface if RDPROTECT and WRTPROTECT bits are nonzero values. Type 1
does not allow the use of 32 byte commands.
Type 2 - Provides checking control and additional expected fields within the 32 byte CDBs. Eight bytes of Pro-
tection Information are transmitted at LBA boundaries across the interface if RDPROTECT and WRTPRO-
TECT bits are nonzero values. Type 2 does allow the use of 10 and 16 byte commands with zero values in the
RDPROTECT and WRTPROTECT fields. The drive will generate 8 bytes of Protection Information (e.g.
0xFFFFFFFF) to be stored on the media, but the 8 bytes will not be transferred to the host during a READ
command.
Type 3 - Seagate products do not support Type 3.
9.6.2
Setting and determining the current Type Level
A drive is initialized to a type of PI by using the FORMAT UNIT command on a PI capable drive. Once a drive
is formatted to a PI Type, it may be queried by a READ CAPACITY (16) command to report the PI type which it
is currently formatted to. A drive can only be formatted to a single PI Type. It can be changed at anytime to a
new Type but requires a FORMAT UNIT command which destroys all existing data on the drive. No other vehi-
cle for changing the PI type is provided by the T10 SBC3 specification.
Type 1 PI FORMAT UNIT CDB command: 04 90 00 00 00 00, parameter data: 00 A0 00 00
Type 2 PI FORMAT UNIT CDB command: 04 D0 00 00 00 00, parameter data: 00 A0 00 00
9.6.3
Identifying a Protection Information drive
The Standard INQUIRY data provides a bit to indicate if PI is support by the drive. Vital Product Descriptor
(VPD) page 0x86 provides bits to indicate the PI Types supported and which PI fields the drive supports check-
ing.
Note. For further details with respect to PI, please refer to SCSI Block Commands - 3 (SBC-3) Draft Stan-
dard documentation.
40
Pulsar XT.2 SAS Product Manual, Rev. B
10.0
Installation
Pulsar XT.2 drive installation is a plug-and-play process. There are no jumpers on the drive.
SAS drives are designed to be used in a host system that provides a SAS-compatible backplane with bays
designed to accommodate the drive. In such systems, the host system typically provides a carrier or tray into
which the drive must be mounted. Mount the drive to the carrier or tray provided by the host system using four
M3 x 0.5 metric screws. When tightening the screws, use a maximum torque of 4.5 in-lb +/- 0.45 in-lb. Do not
over-tighten or force the screws. The drive can be mounted in any orientation.
Note. SAS drives are designed to be attached to the host system without I/O or power cables. If the intent
is to use the drive in a non-backplane host system, connecting the drive using high-quality cables is
acceptable as long as the I/O cable length does not exceed 10 meters (32.8 feet).
Slide the carrier or tray into the appropriate bay in the host system using the instructions provided by the host
system. This connects the drive directly to the system’s SAS connector. The SAS connector is normally located
Power is supplied through the SAS connector.
The drive is shipped from the factory low-level formatted in 512-byte logical blocks. Reformatting the drive is
only required if the application requires a different logical block size.
Figure 12. Physical interface
10.1
Drive orientation
The drive may be mounted in any orientation. All drive performance characterizations, however, have been
done with the drive in horizontal (level) and vertical (drive on its side) orientations, which are the two preferred
mounting orientations.
Pulsar XT.2 SAS Product Manual, Rev. B
41
10.2
Cooling
Cabinet cooling must be designed by the customer so that the temperature of the drive will not exceed temper-
The rack, cabinet, or drawer environment for the drive must provide heat removal from the assembly. The sys-
tem designer should confirm that adequate heat removal is provided using the temperature measurement
guidelines described in Section 7.5.1.
Forced air flow may be required to keep temperatures at or below the temperatures specified in Section 7.5.1
in which case the drive should be oriented, or air flow directed, so that the least amount of air flow resistance is
created while providing air flow. Also, the shortest possible path between the air inlet and exit should be cho-
sen to minimize the travel length of air heated by the drive and other heat sources within the rack, cabinet, or
drawer environment.
If forced air is determined to be necessary, possible air-flow patterns are shown in Figure 13. The air-flow pat-
terns are created by one or more fans, either forcing or drawing air as shown in the illustrations. Conduction,
convection, or other forced air-flow patterns are acceptable as long as the temperature measurement guide-
Above unit
Under unit
Note. Air flows in the direction shown (back to front)
or in reverse direction (front to back)
Above unit
Under unit
Note. Air flows in the direction shown or
in reverse direction (side to side)
Figure 13. Air flow
Note. Image may not represent actual product, for reference only.
42
Pulsar XT.2 SAS Product Manual, Rev. B
10.3
Drive mounting
Mount the drive using the bottom or side mounting holes. If mounting the drive using the bottom holes, ensure
that you do not physically distort the drive by attempting to mount it on a stiff, non-flat surface.
The allowable mounting surface stiffness is 80 lb/in (14.0 N/mm). The following equation and paragraph define
the allowable mounting surface stiffness:
K x X = F < 15lb = 67N
where K is the mounting surface stiffness (units in lb/in or N/mm) and X is the out-of-plane surface distortion
(units in inches or millimeters). The out-of-plane distortion (X) is determined by defining a plane with three of
the four mounting points fixed and evaluating the out-of-plane deflection of the fourth mounting point when a
known force (F) is applied to the fourth point.
10.4
Grounding
Signal ground (PCBA) and case ground are connected together in the drive and cannot be separated by the
user. The equipment in which the drive is mounted is connected directly to the drive with no electrically isolat-
ing shock mounts. If it is desired for the system chassis to not be connected to the drive ground, the systems
integrator or user must provide a nonconductive (electrically isolating) method of mounting the drive in the host
equipment.
Increased radiated emissions may result if designers do not provide the maximum surface area ground con-
nection between system ground and drive ground. This is the system designer’s and integrator’s responsibility.
Pulsar XT.2 SAS Product Manual, Rev. B
43
11.0
Interface requirements
This section partially describes the interface requirements as implemented on Pulsar XT.2 drives. Additional
information is provided in the SAS Interface Manual (part number 100293071).
11.1
SAS features
This section lists the SAS-specific features supported by Pulsar XT.2 drives.
11.1.1
Task management functions
Table 12:
SAS task management functions supported
Task name
Abort Task
Supported
Yes
Abort task set
Clear ACA
Yes
Yes
Clear task set
Yes
I_T Nexus Reset
Logical Unit Reset
Query Task
Yes
Yes
Yes
Yes
Yes
Query Task Set
Query Asynchronous Event
11.1.2
Task management responses
Table 13:
Task management response codes
Function name
Function complete
Invalid frame
Response code
00
02
04
05
08
09
Function not supported
Function failed
Function succeeded
Invalid logical unit
44
Pulsar XT.2 SAS Product Manual, Rev. B
11.2
Dual port support
Pulsar XT.2 SAS drives have two independent ports. These ports may be connected in the same or different
SCSI domains. Each drive port has a unique SAS address.
The two ports have the capability of independent port clocking (e.g. both ports can run at 6Gb/s or the first port
can run at 6Gb/s while the second port runs at 3Gb/s.) The supported link rates are 1.5, 3.0, or 6.0 Gb/s.
Subject to buffer availability, the Pulsar XT.2 drives support:
• Concurrent port transfers—The drive supports receiving COMMAND, TASK management transfers on both
ports at the same time.
• Full duplex—The drive supports sending XFER_RDY, DATA and RESPONSE transfers while receiving
frames on both ports.
Pulsar XT.2 SAS Product Manual, Rev. B
45
11.3
SCSI commands supported
Table 14 lists the SCSI commands supported by Pulsar XT.2 drives.
Table 14: Supported commands
Command name
Command code
Supported
CHANGE DEFINITION
FORMAT UNIT [1]
40h
04h
N
Y
N
Y
Y
Y
Y
Y
N
Y
Y
Y
Y
Y
Y
Y
Y
N
Y
Y
Y
Y
Y
Y
Y
Y
N
Y
Y
N
N
N
Y
N
Y
N
Y
Y
Y
DPRY bit supported
DCRT bit supported
STPF bit supported
IP bit supported
DSP bit supported
IMMED bit supported
VS (vendor specific)
INQUIRY
12h
Block Limits page (B0h)
Block Device Characteristics page (B1h)
Date Code page (C1h)
Device Behavior page (C3h)
Device Identification page (83h)
Extended Inquiry Data page (86h)
Firmware Numbers page (C0h)
Jumper Settings page (C2h)
Power Conditions page (8Ah)
Supported Vital Product Data page (00h)
Thin Provisioning page (B2h)
Unit Serial Number page (80h)
Vendor Unique page (D1h)
Vendor Unique page (D2h)
LOG SELECT
4Ch
PCR bit
DU bit
DS bit
TSD bit
ETC bit
TMC bit
LP bit
LOG SENSE
4Dh
Application Client Log page (0Fh)
Background Scan Results log page (15h)
Buffer Over-run/Under-run page (01h)
Cache Statistics page (37h)
Factory Log page (3Eh)
Information Exceptions Log page (2Fh)
46
Pulsar XT.2 SAS Product Manual, Rev. B
Table 14:
Supported commands
Command name
Command code
Supported
Last n Deferred Errors or Asynchronous Events page (0Bh)
Last n Error Events page (07h)
Non-medium Error page (06h)
Pages Supported list (00h)
N
N
Y
Y
Protocol-Specific Port log pages (18h)
Read Error Counter page (03h)
Read Reverse Error Counter page (04h)
Self-test Results page (10h)
Solid State Media log page (11h)
Start-stop Cycle Counter page (0Eh)
Temperature page (0Dh)
Y
Y
N
Y
Y
Y
Y
Vendor Unique page (3Ch)
Y
Verify Error Counter page (05h)
Write error counter page (02h)
MODE SELECT (6) (same pages as MODE SENSE (6))
MODE SELECT (10) (same pages as MODE SENSE (6))
MODE SENSE (6)
Y
Y
15h
55h
1Ah
Y [3]
Y
Y [3]
Y
Caching Parameters page (08h)
Control Mode page (0Ah)
Y
Disconnect/Reconnect (02h)
Error Recovery page (01h)
Y
Y
Format page (03h)
N
Y
Information Exceptions Control page (1Ch)
Background Scan mode subpage (1Ch/01h)
Notch and Partition Page (0Ch)
Protocol-Specific LUN mode page (18h)
Protocol-Specific Port page (19h)
Power Condition page (1Ah)
Rigid Disc Drive Geometry page (04h)
Unit Attention page (00h)
Y
N
Y
Y
Y
N
Y
Verify Error Recovery page (07h)
Xor Control page (10h)
Y
N
Y
MODE SENSE (10) (same pages as MODE SENSE (6))
PERSISTENT RESERVE IN
PERSISTENT RESERVE OUT
PRE-FETCH (10)
5Ah
5Eh
5Fh
34h
08h
28h
Y
Y
N
Y
READ (6)
READ (10)
Y
DPO bit supported
Y
FUA bit supported
Y
READ (12)
A8h
88h
N
Y
READ (16)
Pulsar XT.2 SAS Product Manual, Rev. B
47
Table 14:
Supported commands
Command name
Command code
7Fh/0009h
3Ch
Supported
READ (32)
Y
READ BUFFER (modes 0, 2, 3, Ah And Bh supported)
READ CAPACITY (10)
READ CAPACITY (16)
READ DEFECT DATA (10)
READ DEFECT DATA (12)
READ LONG (10)
Y (non-SED drives only)
25h
Y
9Eh/10h
37h
Y
Y
B7h
Y
3Eh
Y (non-SED drives only)
READ LONG (16)
9Eh/11h
07h
Y (non-SED drives only)
REASSIGN BLOCKS
RECEIVE DIAGNOSTIC RESULTS
Supported Diagnostics pages (00h)
Translate page (40h)
RELEASE (6)
Y
1Ch
Y
Y
Y
17h
57h
A0h
03h
Y
RELEASE (10)
Y
REPORT LUNS
Y
REQUEST SENSE
Actual Retry Count bytes
Extended Sense
Y
Y
Y
Field Pointer bytes
Y
RESERVE (6)
16h
56h
Y
3rd Party Reserve
Y
Extent Reservation
RESERVE (10)
N
Y
3rd Party Reserve
Y
Extent Reservation
REZERO UNIT
N
01h
A2h
B5h
0Bh
2Bh
1Dh
Y
SECURITY PROTOCOL IN
SECURITY PROTOCOL OUT
SEEK (6)
Y (SED models only)
Y (SED models only)
Y
Y
Y
Y
N
Y
Y
Y
Y
Y
Y
Y
N
Y
SEEK (10)
SEND DIAGNOSTICS
Supported Diagnostics pages (00h)
Translate page (40h)
START UNIT/STOP UNIT
SYNCHRONIZE CACHE
SYNCHRONIZE CACHE (16)
TEST UNIT READY
UNMAP
1Bh
35h
91h
00h
42H
2Fh
VERIFY (10)
BYTCHK bit
VERIFY (12)
AFh
AFh
VERIFY (16)
48
Pulsar XT.2 SAS Product Manual, Rev. B
Table 14:
Supported commands
Command name
Command code
7Fh/000Ah
0Ah
Supported
VERIFY (32)
Y
WRITE (6)
Y
WRITE (10)
2Ah
Y
DPO bit
Y
FUA bit
Y
WRITE (12)
AAh
N
WRITE (16)
8Ah
Y
WRITE (32)
7Fh/000Bh
2Eh
Y
WRITE AND VERIFY (10)
DPO bit
Y
Y
WRITE AND VERIFY (12)
WRITE AND VERIFY (16)
WRITE AND VERIFY (32)
WRITE BUFFER (modes 0, 2, supported)
WRITE BUFFER
Firmware Download option (modes 5, 7, Ah and Bh) [2]
Firmware Download option (modes 4, 5, 7)
WRITE LONG (10)
WRITE LONG (16)
WRITE SAME (10)
PBdata
AEh
N
8Eh
Y
7Fh/000Ch
3Bh
Y
Y (non-SED drives only)
3Bh
Y (non-SED drives only)
Y (SED drives only)
3Fh
Y
Y
Y
N
N
Y
Y
N
N
N
9Fh/11h
41h
LBdata
WRITE SAME (16)
WRITE SAME (32)
XDREAD
93h
7Fh/000Dh
52h
XDWRITE
50h
XPWRITE
51h
[1] Pulsar XT.2 drives can format to 512, 520, 524, 528, 4096, 4160, 4192 and 4224 bytes per logical block.
[2] Warning. Power loss during a firmware upgrade can result in firmware corruption. This usually makes the
drive inoperable.
[3] Reference MODE SENSE command 1Ah for mode pages supported.
[4] Y = Yes. Command is supported.
N = No. Command is not supported.
A = Support is available on special request.
Pulsar XT.2 SAS Product Manual, Rev. B
49
11.3.1
INQUIRY data
Table 15 lists the INQUIRY command data that the drive should return to the initiator per the format given in the
SAS Interface Manual.
Table 15:
Pulsar XT.2 INQUIRY data
Data (hex)
Bytes
0-15
00
[53
R#
00
00
00
00
00
54
R#
00
00
00
43
xx** 12
8B
30
S#
00
00
00
79
53
74
01
46
S#
00
00
00
72
65
73
PP
58
S#
00
00
00
69
61
20
02
30
S#
00
00
00
67
67
72
53
30
S#
00
00
00
68
61
65
45
31
S#
00
00
00
74
74
73
41
32]
S#
00
00
00
20
65
65
47
20
S#
00
00
00
28
20
72
41
20
00
00
00
00
63
41
76
54
20
00
00
00
00
29
6C
65
45
20
00
00
00
00
20
6C
64
20
20
00
00
00
00
Vendor ID
Product ID
16-31
32-47
48-63
64-79
80-95
96-111
112-127
128-143
34
R#
00
00
00
6F
30
R#
00
00
00
70
20
68
32* *Copyright
30* 31* 31*
72 69 67
20
20
notice
*
Copyright year (changes with actual year).
SCSI Revision support. See the appropriate SPC release documentation for definitions.
**
PP 10 = INQUIRY data for an INQUIRY command received on Port A.
30 = INQUIRY data for an INQUIRY command received on Port B.
R# Four ASCII digits representing the last four digits of the product firmware release number.
S# Eight ASCII digits representing the eight digits of the product serial number.
[ ]
Bytes 16 through 26 reflect model of drive. The table above shows the hex values for Model ST400FX0012.
Refer to the values below for the values of bytes 16 through 26 for a particular model:
ST400FX0002
ST200FX0002
ST100FX0002
53 54 34 30 30 46 58 30 30 30 32
53 54 32 30 30 46 58 30 30 30 32
53 54 31 30 30 46 58 30 30 30 32
11.3.2
MODE SENSE data
The MODE SENSE command provides a way for the drive to report its operating parameters to the initiator.
The drive maintains four sets of mode parameters:
1. Default values
Default values are hard-coded in the drive firmware stored in flash E-PROM (nonvolatile memory) on the
drive’s PCB. These default values can be changed only by downloading a complete set of new firmware
into the flash E-PROM. An initiator can request and receive from the drive a list of default values and use
those in a MODE SELECT command to set up new current and saved values, where the values are
changeable.
50
Pulsar XT.2 SAS Product Manual, Rev. B
2. Saved values
Saved values are stored on the drive’s media using a MODE SELECT command. Only parameter values
that are allowed to be changed can be changed by this method. Parameters in the saved values list that
are not changeable by the MODE SELECT command get their values from default values storage.
When power is applied to the drive, it takes saved values from the media and stores them as current val-
ues in volatile memory. It is not possible to change the current values (or the saved values) with a MODE
SELECT command before the drive is “ready.” An attempt to do so results in a “Check Condition” status.
On drives requiring unique saved values, the required unique saved values are stored into the saved val-
ues storage location on the media prior to shipping the drive. Some drives may have unique firmware with
unique default values also.
On standard OEM drives, the saved values are taken from the default values list and stored into the saved
values storage location on the media prior to shipping.
3. Current values
Current values are volatile values being used by the drive to control its operation. A MODE SELECT com-
mand can be used to change the values identified as changeable values. Originally, current values are
installed from saved or default values after a power on reset, hard reset, or Bus Device Reset message.
4. Changeable values
Changeable values form a bit mask, stored in nonvolatile memory, that dictates which of the current values
and saved values can be changed by a MODE SELECT command. A one (1) indicates the value can be
changed. A zero (0) indicates the value is not changeable. For example, in Table 16, refer to Mode page
81, in the row entitled “CHG.” These are hex numbers representing the changeable values for Mode page
81. Note in columns 5 and 6 (bytes 04 and 05), there is 00h which indicates that in bytes 04 and 05 none of
the bits are changeable. Note also that bytes 06, 07, 09, 10, and 11 are not changeable, because those
fields are all zeros. In byte 02, hex value FF equates to the binary pattern 11111111. If there is a zero in any
bit position in the field, it means that bit is not changeable. Since all of the bits in byte 02 are ones, all of
these bits are changeable.
The changeable values list can only be changed by downloading new firmware.
Note. Because there are often several different versions of drive control firmware in the total population of
drives in the field, the MODE SENSE values given in the following tables may not exactly match
those of some drives.
The following tables list the values of the data bytes returned by the drive in response to the MODE SENSE
command pages for SCSI implementation (see the SAS Interface Manual).
DEF = Default value. Standard OEM drives are shipped configured this way.
CHG = Changeable bits; indicates if default value is changeable.
Pulsar XT.2 SAS Product Manual, Rev. B
51
Table 16:
MODE SENSE data for 400GB drives
MODE DATA HEADER:
01 3e 00 10 01 00 00 10
BLOCK DESCRIPTOR:
00 00 00 00 2e 93 90 b0 00 00 00 00 00 00 02 00
MODE PAGES:
DEF 81 0a c0 01 5a 00 00 00 0b 00 ff ff
CHG 81 0a 38 00 00 00 00 00 ff 00 00 00
DEF 82 0e 00 00 00 00 00 00 00 00 01 3a 00 00 00 00
CHG 82 0e 00 00 00 00 00 00 00 00 ff ff 00 00 00 00
DEF 87 0a c0 01 5a 00 00 00 00 00 ff ff
CHG 87 0a 38 00 00 00 00 00 00 00 ff ff
DEF 88 12 14 00 ff ff 00 00 ff ff ff ff a0 20 00 00 00 00 00 00
CHG 88 12 a5 00 00 00 ff ff ff ff 00 00 01 00 00 00 00 00 00 00
DEF 8a 0a 00 00 00 80 00 00 00 00 7f ff
CHG 8a 0a 07 f0 00 00 00 00 00 00 00 00
DEF 18 06 06 00 00 00 00 00
CHG 18 06 00 00 00 00 00 00
DEF 99 0e 46 00 07 d0 00 00 00 00 00 00 00 00 00 00
CHG 99 0e 50 00 ff ff ff ff ff ff 00 00 00 00 00 00
DEF 59 01 00 64 00 06 00 02 00 00 00 00 14 1a 0e 00 50 00 c5 00 00 1a b2 81 50 06 05
b0 01 49 c2 60 02 00 00 00 00 00 00 00 88 aa 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 01 00 00 10 29 0e 00 50 00 c5 00 00 1a b2 82 50 06 05 b0 00 00 fe e4 06
00 00 00 00 00 00 00 88 aa 00 00 00 00 00 00 00 00 00 00 00 00 00 00
CHG 59 01 00 64 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
DEF 59 03 00 2c 00 06 00 02 00 00 00 10 80 ac 00 01 80 ac 00 01 80 bc 00 00 00 00 1a
00 00 01 00 10 80 ac 00 01 80 ac 00 01 00 00 00 00 00 00 09 00
CHG 59 03 00 2c 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
DEF 9a 0a 00 02 00 00 00 05 00 00 8c a0
CHG 9a 0a 00 02 ff ff ff ff 00 00 00 00
DEF 9c 0a 10 00 00 00 00 00 00 00 00 01
CHG 9c 0a 9d 0f ff ff ff ff ff ff ff ff
DEF dc 01 00 0c 01 00 01 50 00 18 00 00 00 00 00 00
CHG dc 01 00 0c 00 00 ff ff ff ff 00 00 00 00 00 00
DEF 80 06 00 80 00 00 00 00
CHG 80 06 b7 80 00 00 00 00
52
Pulsar XT.2 SAS Product Manual, Rev. B
Table 17:
MODE SENSE data for 200GB drives
MODE DATA HEADER:
01 3e 00 10 01 00 00 10
BLOCK DESCRIPTOR:
00 00 00 00 17 49 f1 b0 00 00 00 00 00 00 02 00
MODE PAGES:
DEF 81 0a c0 01 5a 00 00 00 0b 00 ff ff
CHG 81 0a 38 00 00 00 00 00 ff 00 00 00
DEF 82 0e 00 00 00 00 00 00 00 00 01 3a 00 00 00 00
CHG 82 0e 00 00 00 00 00 00 00 00 ff ff 00 00 00 00
DEF 87 0a c0 01 5a 00 00 00 00 00 ff ff
CHG 87 0a 38 00 00 00 00 00 00 00 ff ff
DEF 88 12 14 00 ff ff 00 00 ff ff ff ff a0 20 00 00 00 00 00 00
CHG 88 12 a5 00 00 00 ff ff ff ff 00 00 01 00 00 00 00 00 00 00
DEF 8a 0a 00 00 00 80 00 00 00 00 7f ff
CHG 8a 0a 07 f0 00 00 00 00 00 00 00 00
DEF 18 06 06 00 00 00 00 00
CHG 18 06 00 00 00 00 00 00
DEF 99 0e 46 00 07 d0 00 00 00 00 00 00 00 00 00 00
CHG 99 0e 50 00 ff ff ff ff ff ff 00 00 00 00 00 00
DEF 59 01 00 64 00 06 00 02 00 00 00 00 14 1a 0e 00 50 00 c5 00 00 1a 4b 59 50 06 05
b0 01 49 c2 60 02 00 00 00 00 00 00 00 88 aa 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 01 00 00 10 29 0e 00 50 00 c5 00 00 1a 4b 5a 50 06 05 b0 00 00 fe e4 06
00 00 00 00 00 00 00 88 aa 00 00 00 00 00 00 00 00 00 00 00 00 00 00
CHG 59 01 00 64 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
DEF 59 03 00 2c 00 06 00 02 00 00 00 10 80 ac 00 01 80 ac 00 01 80 bc 00 00 00 00 1a
00 00 01 00 10 80 ac 00 01 80 ac 00 01 00 00 00 00 00 00 09 00
CHG 59 03 00 2c 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
DEF 9a 0a 00 02 00 00 00 05 00 00 8c a0
CHG 9a 0a 00 02 ff ff ff ff 00 00 00 00
DEF 9c 0a 10 00 00 00 00 00 00 00 00 01
CHG 9c 0a 9d 0f ff ff ff ff ff ff ff ff
DEF dc 01 00 0c 01 00 01 50 00 18 00 00 00 00 00 00
CHG dc 01 00 0c 00 00 ff ff ff ff 00 00 00 00 00 00
DEF 80 06 00 80 00 00 00 00
CHG 80 06 b7 80 00 00 00 00
Pulsar XT.2 SAS Product Manual, Rev. B
53
Table 18:
MODE SENSE values for 100GB drives
MODE DATA HEADER:
01 3e 00 10 01 00 00 10
BLOCK DESCRIPTOR:
00 00 00 00 0b a5 22 30 00 00 00 00 00 00 02 00
MODE PAGES:
DEF 81 0a c0 01 5a 00 00 00 0b 00 ff ff
CHG 81 0a 38 00 00 00 00 00 ff 00 00 00
DEF 82 0e 00 00 00 00 00 00 00 00 01 3a 00 00 00 00
CHG 82 0e 00 00 00 00 00 00 00 00 ff ff 00 00 00 00
DEF 87 0a c0 01 5a 00 00 00 00 00 ff ff
CHG 87 0a 38 00 00 00 00 00 00 00 ff ff
DEF 88 12 14 00 ff ff 00 00 ff ff ff ff a0 20 00 00 00 00 00 00
CHG 88 12 a5 00 00 00 ff ff ff ff 00 00 01 00 00 00 00 00 00 00
DEF 8a 0a 00 00 00 80 00 00 00 00 7f ff
CHG 8a 0a 07 f0 00 00 00 00 00 00 00 00
DEF 18 06 06 00 00 00 00 00
CHG 18 06 00 00 00 00 00 00
DEF 99 0e 46 00 07 d0 00 00 00 00 00 00 00 00 00 00
CHG 99 0e 50 00 ff ff ff ff ff ff 00 00 00 00 00 00
DEF 59 01 00 64 00 06 00 02 00 00 00 00 14 1a 0e 00 50 00 c5 00 00 1a 3a ed 50 06 05
b0 01 49 c2 60 02 00 00 00 00 00 00 00 88 aa 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 01 00 00 10 29 0e 00 50 00 c5 00 00 1a 3a ee 50 06 05 b0 00 00 fe e4 06
00 00 00 00 00 00 00 88 aa 00 00 00 00 00 00 00 00 00 00 00 00 00 00
CHG 59 01 00 64 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
DEF 59 03 00 2c 00 06 00 02 00 00 00 10 80 ac 00 01 80 ac 00 01 80 bc 00 00 00 00 1a
00 00 01 00 10 80 ac 00 01 80 ac 00 01 00 00 00 00 00 00 09 00
CHG 59 03 00 2c 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
DEF 9a 0a 00 02 00 00 00 05 00 00 8c a0
CHG 9a 0a 00 02 ff ff ff ff ff ff ff ff
DEF 9c 0a 10 00 00 00 00 00 00 00 00 01
CHG 9c 0a 9d 0f ff ff ff ff 00 00 00 00
DEF dc 01 00 0c 01 00 01 50 00 18 00 00 00 00 00 00
CHG dc 01 00 0c 00 00 ff ff ff ff 00 00 00 00 00 00
DEF 80 06 00 80 00 00 00 00
CHG 80 06 b7 80 00 00 00 00
54
Pulsar XT.2 SAS Product Manual, Rev. B
11.4
Miscellaneous operating features and conditions
Table 19 lists various features and conditions. A “Y” in the support column indicates the feature or condition is
supported. An “N” in the support column indicates the feature or condition is not supported.
Table 19:
Miscellaneous features
Supported
Feature or condition
Automatic contingent allegiance
N
N
Y
N
Y
Y
Y
Y
Asynchronous event notification
Segmented caching
Zero latency read
Queue tagging (up to 128 queue tags supported)
Deferred error handling
Parameter rounding (controlled by Round bit in MODE SELECT page 0)
Reporting actual retry count in Extended Sense bytes 15, 16, and 17
Table 20:
Miscellaneous status
Supported
Status
Good
Y
Y
Y
Y
Y
Y
N
N
N
Check condition
Condition met/good
Busy
Reservation conflict
Task set full
ACA active
ACA active, faulted initiator
Task Aborted
11.4.1
SAS physical interface
Figure 14 shows the location of the SAS device connector J1. Figures 15 and 16 provide the dimensions of the
SAS connector.
Details of the physical, electrical, and logical characteristics are provided within this section. The operational
aspects of Seagate’s SAS drives are provided in the SAS Interface Manual.
Figure 14. Physical interface
Pulsar XT.2 SAS Product Manual, Rev. B
55
0.80 (6X)
5.92
7.62
4.65
0.52 0.08 x 45
2.00 (3X)
0.45 0.03 (7X)
0.10 M E
5.08
42.73 REF.
41.13 0.15
0.20B
0.30 0.05 (2X)
C
A
B
1.10
4.00 0.08
0.15D
C OF DATUM D
L
R0.30 0.08 (4X)
A
0.30 0.05 (4X)
B
C
SEE Detail1
B
33.43 0.05
15.875
15.875
1.27 (14X)
1.27 (6X)
0.84 0.05 (22X)
5.08
0.15B
4.90 0.08
0.35MIN
P15
S1
P1
S7
C OF DATUM B
L
Figure 15. SAS device plug dimensions
56
Pulsar XT.2 SAS Product Manual, Rev. B
Detail A
6.10
S14
S8
0.30 0.05 x 45 (5X)
2.25 0.05
0.40 0.05 X 45 (3X)
4.85 0.05
0.10B
CORING ALLOWED
IN THIS AREA.
E
4.40 0.15
R0.30 0.08
45
C
SEE Detail 2
1.95 0.08
A
0.35 0.05
SECTION C - C
3.90 0.15
SECTION A - A
CONTACT SURFACE FLUSH
TO DATUM A 0.03
0.08 0.05
65
1.90 0.08
1.23 0.05
0.08 0.05
30
Detail 2
2.40 0.08
0.10 A
SECTION B - B
D
Figure 16. SAS device plug dimensions (detail)
Pulsar XT.2 SAS Product Manual, Rev. B
57
11.4.2
Physical characteristics
This section defines physical interface connector.
11.4.3
Connector requirements
Contact your preferred connector manufacturer for mating part information. Part numbers for SAS connectors
will be provided in a future revision of this publication when production parts are available from major connec-
tor manufacturers.
The SAS device connector is illustrated in Figures 15 and 16.
11.4.4
Electrical description
SAS drives use the device connector for:
• DC power
• SAS interface
• Activity LED
This connector is designed to either plug directly into a backpanel or accept cables.
11.4.5
Pin descriptions
This section provides a pin-out of the SAS device and a description of the functions provided by the pins.
Table 21:
SAS pin descriptions
Pin
S1
Signal name Signal type
Pin
P1*
P2*
P3
Signal name
NC (reserved 3.3Volts)
NC (reserved 3.3Volts)
NC (reserved 3.3Volts)
Ground
Signal type
Port A Ground
+Port A_in
S2*
S3*
S4
Diff. input pair
Diff output pair
-Port A_in
Port A Ground
-Port A_out
+Port A_out
Port A Ground
Port B Ground
+Port B_in
P4
S5*
S6*
S7
P5
Ground
P6
Ground
P7
5 Volts charge
5 Volts
S8
P8*
P9*
P10
P11*
P12
P13
P14*
P15*
S9*
S10*
S11
S12*
S13*
S14
Diff. input pair
Diff output pair
5 Volts
-Port B_in
Ground
Port A Ground
-Port B_out
+Port B_out
Port B Ground
Ready LED
Ground
Open collector out
12 Volts charge
12 Volts
12 Volts
* - Short pin to support hot plugging
NC - No connection in the drive.
58
Pulsar XT.2 SAS Product Manual, Rev. B
11.4.6
SAS transmitters and receivers
A typical SAS differential copper transmitter and receiver pair is shown in Figure 17. The receiver is AC cou-
pling to eliminate ground shift noise.
.01
TX
TY
RX
Differential
Transfer Medium
Transmitter
100
Receiver
100
RY
.01
Figure 17. SAS transmitters and receivers
11.4.7 Power
The drive receives power (+5 volts and +12 volts) through the SAS device connector.
Three +12 volt pins provide power to the drive, 2 short and 1 long. The current return for the +12 volt power
supply is through the common ground pins. The supply current and return current must be distributed as
evenly as possible among the pins.
Three +5 volt pins provide power to the drive, 2 short and 1 long. The current return for the +5 volt power sup-
ply is through the common ground pins. The supply current and return current must be distributed as evenly as
possible among the pins.
Current to the drive through the long power pins may be limited by the system to reduce inrush current to the
drive during hot plugging.
11.5
Signal characteristics
This section describes the electrical signal characteristics of the drive’s input and output signals. See Table 21
for signal type and signal name information.
11.5.1
Ready LED Out
Table 22:
Ready LED Out conditions
Normal command activity
LED status
Ready LED Meaning bit mode page 19h
Drive stopped, not ready, and no activity
0
1
Off
On
Off
On
Drive stopped, not ready, and activity
(command executing)
Drive started, ready, and no activity
On
Off
Off
On
Drive started, ready, and activity
(command executing)
Drive transitioning from not-ready state to
ready state or the reverse.
Blinks steadily
(50% on and 50% off, 0.5 seconds on and off for 0.5 seconds)
FORMAT UNIT in progress,
Toggles on/off
Pulsar XT.2 SAS Product Manual, Rev. B
59
The Ready LED Out signal is designed to pull down the cathode of an LED. The anode is attached to the
proper +3.3 volt supply through an appropriate current limiting resistor. The LED and the current limiting resis-
tor are external to the drive. See Table 23 for the output characteristics of the LED drive signals.
Table 23:
LED drive signal
State
Test condition
0 V ≤VOH ≤3.6 V
= 15 mA
Output voltage
LED off, high
LED on, low
-100 µA < I < 100 µA
OH
I
0 ≤VOL ≤0.225 V
OL
11.5.2
Differential signals
The drive SAS differential signals comply with the intra-enclosure (internal connector) requirements of the SAS
standard.
Table 24 defines the general interface characteristics
Table 24:
General interface characteristics
Characteristic
Units
Mbaud
ps
1.5Gb/s
1,500
666.6
100
3.0Gb/s
3,000
333.3
100
6.0Gb/s
6,000
166.6
100
Bit rate (nominal)
Unit interval (UI)(nominal)
Impedance (nominal, differential )
Transmitter transients, maximum
Receiver transients, maximum
ohm
V
1.2
1.2
1.2
V
1.2
1.2
1.2
11.6
SAS-2 Specification compliance
Seagate SAS-2 drives are entirely compatible with the latest SAS-2 Specification (T10/1760-D) Revision 16.
The most important characteristic of the SAS-2 drive at 6Gb/s is that the receiver is capable of adapting the
equalizer to optimize the receive margins. The SAS-2 drive has two types of equalizers:
1. A Decision Feedback Equalizer (DFE) which utilizes the standard SAS-2 training pattern transmitted dur-
ing the SNW-3 training gap. The DFE circuit can derive an optimal equalization characteristic to compen-
sate for many of the receive losses in the system.
2. A Feed Forward Equalizer (FFE) optimized to provide balanced receive margins over a range of channels
bounded by the best and worst case channels as defined by the relevant ANSI standard.
11.7
Additional information
Please contact your Seagate representative for SAS electrical details, if required.
For more information about the Phy, Link, Transport, and Applications layers of the SAS interface, refer to the
Seagate SAS Interface Manual, part number 100293071.
For more information about the SCSI commands used by Seagate SAS drives, refer to the Seagate SCSI
Commands Reference Manual, part number 100293068.
60
Pulsar XT.2 SAS Product Manual, Rev. B
CBC 35
Index
condensation 30
connector
Numerics
12 volt
pins 59
A
illustrated 58
requirements 58
cooling 42
CRC
access time
error 15
D
data block size
illustrated 42
requirements 23
decrypt 35
defects 38
altitude 30
ambient 30
ANSI documents
SCSI 5
Auto-Reallocation 39
DEK 35
description 6
DFE 60
B
dimensions 33
drive 32
backpanel 58
BandMasterX 36
BMS 39
C
E
capacity
unformatted 11
case 43
electrical
specifications 22
Pulsar XT.2 SAS Product Manual, Rev. B
61
Endurance 14
environment 42
environmental
limits 29
requirements 14
EraseMaster 36
error
I
installation 41
guide 5
interface
errors 15
illustrated 55
physical 55
management 38
rates 14
errors 38
requirements 44
European Union Restriction of Hazardous Substanc-
es 4
J
jumpers 41
F
L
features 6
interface 44
FFE 60
firmware 6
LockOnReset 36
corruption 49
function
M
maintenance 14
miscellaneous feature support
G
gradient 30
grounding 43
H
humidity 30
miscellaneous status support
Busy 55
Good 55
62
Pulsar XT.2 SAS Product Manual, Rev. B
power 59
dissipation 28
Mode sense
mounting 43
sequencing 26
PowerChoice 22
PowerCycle 36
holes 43
orientations 41
N
noise
Q
audible 3
temperature 30
R
receivers 59
reference
O
options 8
documents 5
reliability 7
specifications 14
P
resonance 30
RNG 36
packaged 31
passwords 36
PCBA 43
Performance 12
detailed 11
S
safety 3
SAS
interface 58
SCSI interface
Pulsar XT.2 SAS Product Manual, Rev. B
63
Self-Monitoring Analysis and Reporting Technology
U
unformatted 8
shielding 3
shipping 21
shock 31
V
voltage 22
SID 35
signal
W
characteristics 59
warranty 21
Specification 60
standards 3
Z
surface stiffness
T
TCG 35
limits 29
non-operating 30
regulation 3
See also cooling
transmitters 59
64
Pulsar XT.2 SAS Product Manual, Rev. B
Seagate Technology LLC
AMERICAS Seagate Technology LLC 10200 South De Anza Boulevard, Cupertino, California 95014, United States, 408-658-1000
ASIA/PACIFIC Seagate Singapore International Headquarters Pte. Ltd. 7000 Ang Mo Kio Avenue 5, Singapore 569877, 65-6485-3888
EUROPE, MIDDLE EAST AND AFRICA Seagate Technology SAS 16-18 rue du Dôme, 92100 Boulogne-Billancourt, France, 33 1-4186 10 00
Publication Number: 100647497, Rev. B
June 2011
|