Seagate Barracuda 72008 PATA User Manual

Product Manual

Barracuda 7200.8 PATA

ST3400832A

ST3400632A

ST3300831A

ST3300631A

ST3250823A

ST3250623A

ST3200826A

100323825

Rev. F

August 2007

Contents

1.0

2.0

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2.1

2.2

Specification summary table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Formatted capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.2.1

LBA mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Default logical geometry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Recording and interface technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Physical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Seek time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Start/stop times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Power specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Conducted noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Voltage tolerance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Power-management mode s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 4

2.9

Environmental specification s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 5

Ambient temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Temperature gradient. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Altitud e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 5

Shock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Vibratio n . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 6

Acoustics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Electromagnetic immunity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Agency certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

2.13.1

2.13.2

2.13.3

Safety certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Electromagnetic compatibility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

FCC verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

2.14

2.15

Environmental protectio n . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 0

Corrosive environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

3.0

Configuring and mounting the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

3.1

3.2

3.3

Handling and static discharge precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Breather filter hole precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Jumper settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Master/slave configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Cable-select option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Alternate capacity jumper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Ultra ATA/100 cabl e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 4

3.4

Drive mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

4.0

5.0

ATA interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

4.1 ATA interface signals and connector pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Supported ATA commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Identify Device command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Set Features command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

S.M.A.R.T. command s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3

Seagate Technology support service s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 5

Barracuda 7200.8 PATA Product Manual, Rev. F

List of Figures

Figure 7.

Typical 5V startup and operation current profil e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 3

Typical 12V startup and operation current profil e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 3

Breather filter hole locatio n . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2

Master/slave jumper settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Ultra ATA cable connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Mounting dimensions—top, side and end view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

I/O pins and supported ATA signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Barracuda 7200.8 PATA Product Manual, Rev. F

iii

Barracuda 7200.8 PATA Product Manual, Rev. F

1.0

Introduction

This manual describes the functional, mechanical and interface specifications for the following Seagate^®

Barracuda^®7200.8 PATA model drives:

Barracuda 7200.8 PATA

• ST3400832A

• ST3400632A

• ST3300831A

• ST3300631A

• ST3250823A

• ST3250623A

• ST3200826A

These drives provide the following key features:

• 7,200-RPM spindle speed

• 8-Mbyte buffer on: ST3400832A, ST3300831A, ST3250823A and ST3200826A.

• 16-Mbyte buffer on: ST3400632A, ST3300631A, and ST3250623A

• High instantaneous (burst) data transfer rates (up to 100 Mbytes per second) using Ultra DMA mode 5.

• Tunneling Magnetoresistive (TMR) recording heads provide the drives with increased areal density.

• State-of-the-art cache and on-the-fly error-correction algorithms.

• Full-track multiple-sector transfer capability without local processor intervention.

• Quiet operation.

• 300 Gs nonoperating shock.

• SeaTools diagnostic software performs a drive self-test that eliminates unnecessary drive returns.

• Support for S.M.A.R.T. drive monitoring and reporting.

• Support for Read Multiple and Write Multiple commands.

• Support for autodetection of master/slave drives that use cable select (CSEL).

Barracuda 7200.8 PATA Product Manual, Rev. F

2.0

Drive specifications

Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal

power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate

ST3400832A, ST3400632A, ST3300831A, ST3300631A, ST3250823A, ST3250623A, and ST3200826A

model drives.

2.1

Specification summary table

The specifications listed in tables 1, 2, an d 3 are for quick reference. For details on specification measurement

or definition, see the appropriate section of this manual.

Barracuda 7200.8 PATA Product Manual, Rev. F

Table 1:

Drive specifications for 400 Gbyte models

Drive specification

ST3400832A

400

ST3400632A

400

Formatted Gbytes (512 bytes/sector)*

Guaranteed sectors

781,422,768

512

781,422,768

Bytes per sector

Default sectors per track

Default read/write heads

Default cylinders

16,383

763,000

Recording density, BPI

(bits/in max)

Track density, TPI

(tracks/in avg.)

120,000

91,560

Areal density,

(Mbits/in avg)

Spindle speed (RPM)

7,200

Internal data transfer rate (Mbytes/sec max)

Sustained data transfer rate OD (Mbytes/sec)

I/O data-transfer rate (Mbytes/sec max)

100

ATA data-transfer modes

supported

PIO modes 0–4

Multiword DMA modes 0–2

Ultra DMA modes 0–5

Cache buffer

8 Mbytes

16 Mbytes

Height (mm max)

26.11 mm (1.028 inches)

101.85 mm (4.010 inches)

146.99 mm (5.787 inches)

635 grams (1.39 lb.)

4.16

Width (mm max)

Length (mm max)

Weight (max)

Average latency (msec)

Power-on to ready (sec max)

Standby to ready (sec max)

Track-to-track seek time (msec typical)

Average seek, read (msec typical)

Average seek, write (msec typical)

Startup current (typical) 12V (peak)

Seek power (typical)

10.0 sec

0.8 (read), 1.0 (write)

<11.0

<12.0

2.8 amps

12.4 watts

Read/write power (typical)

Idle mode (typical)

12.8 watts

7.2 watts

Standby mode (typical)

Sleep mode (typical)

0.8 watts

Voltage tolerance

(including noise)

5V ± 5%

12V ± 10%

Ambient

0° to 60°C (operating)

temperature

–40° to 70°C (nonoperating)

Temperature gradient

(°C per hour max)

20°C (operating)

30°C (nonoperating)

Relative humidity

5% to 90% (operating)

5% to 95% (nonoperating)

Relative humidity gradient

30% per hour max

Wet bulb temperature

(°C max)

37.7 (operating)

40 (nonoperating)

Altitude, operating

–60.96 m to 3,048 m

(–200 ft. to 10,000+ ft.)

Barracuda 7200.8 PATA Product Manual, Rev. F

Drive specification

ST3400832A

ST3400632A

Altitude, nonoperating

(below mean sea level, max)

–60.96 m to 12,192 m

(–200 ft. to 40,000+ ft.)

Operational Shock (Gs max at 2 msec)

Non-Operational Shock (Gs max at 2 msec)

Vibration, operating

300 Gs

5–22 Hz: Limited displacement

23–350 Hz: 0.5 G acceleration

Vibration, nonoperating

5–22 Hz: Limited displacement

23–350 Hz: 5.0 Gs

Drive acoustics, sound power (bels)

Idle**

2.8 (typical)

3.4 (max)

Performance seek

3.7 (typical)

3.9 (max)

Nonrecoverable read errors

Annualized Failure Rate (AFR)

Service life

1 per 10 bits read

0.34%

5 Years

Warranty

5 years on distribution units.

To determine the warranty for a specific drive, use a

web browser to access the following web page:

www.seagate.com/support/service/

From this page, click on the “Verify Your Warranty”

link. You will be asked to provide the drive serial

number, model number (or part number) and country

of purchase. The system will display the warranty

information for your drive.

Contact start-stop cycles

(25°C, 50% rel. humidity)

50,000

*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment

and formatting.

**During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and

power to operational levels.

Barracuda 7200.8 PATA Product Manual, Rev. F

Table 2:

Drive specifications for 300 Gbyte models

Drive specification

ST3300831A

300

ST3300631A

300

Formatted Gbytes (512 bytes/sector)*

Guaranteed sectors

586,072,368

512

586,072,368

Bytes per sector

Default sectors per track

Default read/write heads

Default cylinders

16,383

763,000

Recording density, BPI

(bits/in max)

Track density, TPI

(tracks/in avg.)

120,000

91,560

Areal density,

(Mbits/in avg)

Spindle speed (RPM)

7,200

Internal data transfer rate (Mbytes/sec max)

Sustained data transfer rate OD (Mbytes/sec)

I/O data-transfer rate (Mbytes/sec max)

100

ATA data-transfer modes

supported

PIO modes 0–4

Multiword DMA modes 0–2

Ultra DMA modes 0–5

Cache buffer

8 Mbytes

16 Mbytes

Height (mm max)

26.11 mm (1.028 inches)

101.85 mm (4.010 inches)

146.99 mm (5.787 inches)

635 grams (1.39 lb.)

4.16

Width (mm max)

Length (mm max)

Weight (max)

Average latency (msec)

Power-on to ready (sec max)

Standby to ready (sec max)

Track-to-track seek time (msec typical)

Average seek, read (msec typical)

Average seek, write (msec typical)

Startup current (typical) 12V (peak)

Seek power (typical)

10.0 sec

0.8 (read), 1.0 (write)

<11.0

<12.0

2.8 amps

12.4 watts

Read/write power (typical)

Idle mode (typical)

12.8 watts

7.2 watts

Standby mode (typical)

Sleep mode (typical)

0.8 watts

Voltage tolerance

(including noise)

5V ± 5%

12V ± 10%

Ambient

0° to 60°C (operating)

temperature

–40° to 70°C (nonoperating)

Temperature gradient

(°C per hour max)

20°C (operating)

30°C (nonoperating)

Relative humidity

5% to 90% (operating)

5% to 95% (nonoperating)

Relative humidity gradient

30% per hour max

Wet bulb temperature

(°C max)

37.7 (operating)

40 (nonoperating)

Altitude, operating

–60.96 m to 3,048 m

(–200 ft. to 10,000+ ft.)

Barracuda 7200.8 PATA Product Manual, Rev. F

Drive specification

ST3300831A

ST3300631A

Altitude, nonoperating

(below mean sea level, max)

–60.96 m to 12,192 m

(–200 ft. to 40,000+ ft.)

Operational Shock (Gs max at 2 msec)

Non-Operational Shock (Gs max at 2 msec)

Vibration, operating

300 Gs

5–22 Hz: Limited displacement

23–350 Hz: 0.5 G acceleration

Vibration, nonoperating

5–22 Hz: Limited displacement

23–350 Hz: 5.0 Gs

Drive acoustics, sound power (bels)

Idle**

2.8 (typical)

3.4 (max)

Performance seek

3.7 (typical)

3.9 (max)

Nonrecoverable read errors

Annualized Failure Rate (AFR)

Service life

1 per 10 bits read

0.34%

5 Years

Warranty

5 years on distribution units.

To determine the warranty for a specific drive, use a web browser to access the

following web page:

www.seagate.com/support/service/

From this page, click on the “Verify Your Warranty” link. You will be asked to pro-

vide the drive serial number, model number (or part number) and country of pur-

chase. The system will display the warranty information for your drive.

Contact start-stop cycles

(25°C, 50% rel. humidity)

50,000

*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment

and formatting.

**During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and

power to operational levels.

Barracuda 7200.8 PATA Product Manual, Rev. F

Table 3:

Drive specifications for 250 and 200 Gbyte models

Drive specification

ST3250823A

250

ST3250623A

250

ST3200826A

200

Formatted Gbytes (512 bytes/sector)*

Guaranteed sectors

488,397,168

512

488,397,168

390,721,968

Bytes per sector

Default sectors per track

Default read/write heads

Default cylinders

16,383

763,000

Recording density, BPI

(bits/in max)

Track density, TPI

(tracks/in avg.)

120,000

91,560

Areal density,

(Mbits/in avg)

Spindle speed (RPM)

7,200

Internal data transfer rate (Mbytes/sec max)

Sustained data transfer rate OD (Mbytes/sec)

I/O data-transfer rate (Mbytes/sec max)

100

ATA data-transfer modes

supported

PIO modes 0–4

Multiword DMA modes 0–2

Ultra DMA modes 0–5

Cache buffer

8 Mbytes

16 Mbytes

8 Mbytes

Height (mm max)

26.11 mm (1.028 inches)

101.85 mm (4.010 inches)

146.99 mm (5.787 inches)

635 grams (1.39 lb.)

4.16

Width (mm max)

Length (mm max)

Weight (max)

Average latency (msec)

Power-on to ready (sec max)

Standby to ready (sec max)

Track-to-track seek time (msec typical)

Average seek, read (msec typical)

Average seek, write (msec typical)

Startup current (typical) 12V (peak)

Seek power (typical)

10.0 sec

0.8 (read), 1.0 (write)

<11.0

<12.0

2.8 amps

12.4 watts

Read/write power (typical)

Idle mode (typical)

12.8 watts

7.2 watts

Standby mode (typical)

Sleep mode (typical)

0.8 watts

Voltage tolerance

(including noise)

5V ± 5%

12V ± 10%

Ambient

0° to 60°C (operating)

temperature

–40° to 70°C (nonoperating)

Temperature gradient

(°C per hour max)

20°C (operating)

30°C (nonoperating)

Relative humidity

5% to 90% (operating)

5% to 95% (nonoperating)

Relative humidity gradient

30% per hour max

Wet bulb temperature

(°C max)

37.7 (operating)

40 (nonoperating)

Barracuda 7200.8 PATA Product Manual, Rev. F

Drive specification

ST3250823A

ST3250623A

ST3200826A

Altitude, operating

–60.96 m to 3,048 m

(–200 ft. to 10,000+ ft.)

Altitude, nonoperating

(below mean sea level, max)

–60.96 m to 12,192 m

(–200 ft. to 40,000+ ft.)

Operational Shock (Gs max at 2 msec)

Non-Operational Shock (Gs max at 2 msec)

Vibration, operating

300 Gs

5–22 Hz: Limited displacement

23–350 Hz: 0.5 G acceleration

Vibration, nonoperating

5–22 Hz: Limited displacement

23–350 Hz: 5.0 Gs

Drive acoustics, sound power (bels)

Idle**

2.8 (typical)

3.4 (max)

Performance seek

3.7 (typical)

3.9 (max)

Nonrecoverable read errors

Annualized Failure Rate (AFR)

Service life

1 per 10 bits read

0.34%

5 Years

Warranty

5 years on distribution units.

To determine the warranty for a specific drive, use a web browser to access the

following web page:

www.seagate.com/support/service/

From this page, click on the “Verify Your Warranty” link. You will be asked to pro-

vide the drive serial number, model number (or part number) and country of pur-

chase. The system will display the warranty information for your drive.

Contact start-stop cycles

(25°C, 50% rel. humidity)

50,000

*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment

and formatting.

**During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and

power to operational levels.

Barracuda 7200.8 PATA Product Manual, Rev. F

2.2

Formatted capacity

Formatted

capacity

Guaranteed

sectors

Model

Bytes per sector

ST3400832A

ST3400632A

ST3300831A

ST3300631A

ST3250823A

ST3250623A

ST3200826A

400 Gbytes

300 Gbytes

250 Gbytes

200 Gbytes

781,422,768

586,072,368

488,397,168

390,721,968

512

2.2.1

LBA mode

When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1,

where n is the number of guaranteed sectors as defined above.

See Section 4.1.2, "Identify Device command" (words 60-61 and 100-103) for additional information about 48-

bit addressing support of drives with capacities over 137 Gbytes.

2.3

Default logical geometry

Cylinders

16,383

Read/write heads

Sectors per track

2.4

Recording and interface technology

Interface

ATA

Recording method

16/17 EPRML

Recording density BPI (bits/inch max)

Track density TPI (tracks/inch avg)

728,000

120,000

Areal density (Mbits/inch avg)

91,560

Spindle speed (RPM) (± 0.2%)

7,200

Internal data-transfer rate (Mbytes/sec max)

Sustained data transfer rate OD (Mbytes/sec max)

I/O data-transfer rate (Mbytes/sec max)

Interleave

65.0

100 (Ultra DMA mode 5)

1:1

Cache buffer

ST3400832A, ST3300831A, ST3250823A and ST3200826A

ST3400632A, ST3300631A, and ST3250623A

8 Mbytes (8,192 kbytes)

16 Mbytes (16,384 kbytes)

Barracuda 7200.8 PATA Product Manual, Rev. F

2.5

Physical characteristics

Drive specification

Maximum height

Maximum width

Maximum length

Max weight

(mm)

(inches)

26.11

1.028

(mm)

(inches)

101.85

4.010

(mm)

(inches)

146.99

5.787

(grams)

(pounds)

635

1.39

2.6

Seek time

Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using

drive diagnostics. The specifications in the table below are defined as follows:

• Track-to-track seek time is an average of all possible single-track seeks in both directions.

• Average seek time is a true statistical random average of at least 5,000 measurements of seeks between

random tracks, less overhead.

*Typical seek times (msec)

Track-to-track

Read

0.8

Write

1.0

Average

<11.0

4.16

<12.0

4.16

Average latency:

*Measured in quiet mode

Note. These drives are designed to consistently meet the seek times represented in this manual. Physical seeks,

regardless of mode (such as track-to-track and average), are expected to meet or exceed the noted values.

However, due to the manner in which these drives are formatted, benchmark tests that include command

overhead or measure logical seeks may produce results that vary from these specifications.

2.7

Start/stop times

Power-on to Ready (sec)

10 (max)

12 (max)

Standby to Ready (sec)

Ready to spindle stop (sec)

Barracuda 7200.8 PATA Product Manual, Rev. F

2.8

Power specifications

The drive receives DC power (+5V or +12V) through a four-pin standard drive power connector.

2.8.1 Power consumption

Power requirements for the drives are listed in the table on page 12. Typical power measurements are based

on an average of drives tested, under nominal conditions, using +5.0V and +12.0V input voltage at 25°C ambi-

ent temperature.

• Spinup power

Spinup power is measured fromthe time ofpower-onto thetimethat the drive spindle reaches operating speed.

• Seek mode

During seek mode, the read/write actuator arm moves toward a specific position on the disc surface and does

not execute a read or write operation. Servo electronics are active. Seek mode power represents the worst-

case power consumption, using only random seeks with read or write latency time. This mode is not typical

and is provided for worst-case information.

• Read/write power and current

Read/write power is measured with the heads on track, based on a 16-sector write followed by a 32-msec

delay, then a 16-sector read followed by a 32-msec delay.

• Operating power and current

Operating power is measured using 40 percent random seeks, 40 percent read/write mode (1 write for each

10 reads) and 20 percent drive idle mode.

• Idle mode power

Idle mode power is measured with the drive up to speed, with servo electronics active and with the heads in

a random track location.

• Standby mode

During Standby mode, the drive accepts commands, but the drive is not spinning, and the servo and read/

write electronics are in power-down mode.

Table 4:

DC power requirements

Power dissipation (watts)

Example: ST3400832A

Average

(watts, 25° C)

5V typ

amps

12V typ

amps

Spinup

—

2.8 (peak)

0.433

Idle

7.2

0.401

0.78

Idle* (with offline activity)

Operating (40% r/w, 40% seek, 20% inop.)

Seeking (random, 20% idle)

Standby

9.1

0.433

12.8

12.4

0.8

0.841

0.602

0.145

0.715

0.782

0.006

Sleep

0.8

0.006

*During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and

power to operational levels.

Barracuda 7200.8 PATA Product Manual, Rev. F

2.8.1.1

Typical current profile

Figure 1

Typical 5V startup and operation current profile

Figure 2

2.8.2

Typical 12V startup and operation current profile

Conducted noise

Input noise ripple is measured at the host system power supply across an equivalent 80-ohm resistive load on

the +12 volt line or an equivalent 15-ohm resistive load on the +5 volt line.

• Using 12-volt power, the drive is expected to operate with a maximum of 120 mV peak-to-peak square-wave

injected noise at up to 10 MHz.

• Using 5-volt power, the drive is expected to operate with a maximum of 100 mV peak-to-peak square-wave

injected noise at up to 10 MHz.

Note. Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read/write

current.

2.8.3

Voltage tolerance

Voltage tolerance (including noise):

5V ± 5%

12V ± 10%

Barracuda 7200.8 PATA Product Manual, Rev. F

2.8.4

Power-management modes

The drive provides programmable power management to provide greater energy efficiency. In most systems,

you can control power management through the system setup program. The drive features the following

power-management modes:

Power mode

Active

Heads

Spindle

Rotating

Stopped

Buffer

Tracking

Parked

Enabled

Disabled

Idle

Standby

Sleep

• Active mode

The drive is in Active mode during the read/write and seek operations.

• Idle mode

The buffer remains enabled, and the drive accepts all commands and returns to Active mode any time disc

access is necessary.

• Standby mode

The drive enters Standby mode when the host sends a Standby Immediate command. If the host has set the

standby timer, the drive can also enter Standby mode automatically after the drive has been inactive for a

specifiable length of time. The standby timer delay is established using a Standby or Idle command. In Standby

mode, the drive buffer is enabled, the heads are parked and the spindle is at rest. The drive accepts all

commands and returns to Active mode any time disc access is necessary.

• Sleep mode

The drive enters Sleep mode after receiving a Sleep command from the host. In Sleep mode, the drive buffer

is disabled, the heads are parked and the spindle is at rest. The drive leaves Sleep mode after it receives a

Hard Reset or Soft Reset from the host. After receiving a reset, the drive exits Sleep mode and enters Standby

mode with all current translation parameters intact.

• Idle and Standby timers

Each time the drive performs an Active function (read, write or seek), the standby timer is reinitialized and

begins counting down from its specified delay times to zero. If the standby timer reaches zero before any drive

activity is required, the drive makes a transition to Standby mode. In both Idle and Standby mode, the drive

accepts all commands and returns to Active mode when disc access is necessary.

Barracuda 7200.8 PATA Product Manual, Rev. F

2.9

Environmental specifications

Ambient temperature

2.9.1

Ambient temperature is defined as the temperature of the environment immediately surrounding the drive.

Actual drive case temperature should not exceed 69°C (156°F) within the operating ambient conditions for

standard models, or 64°C (147°F) within the operating ambient conditions for all models. Recommended mea-

surement locations are shown in See Figure 6 on page 25.

Above 1,000 feet (305 meters), the maximum temperature is derated linearly to 112°F (44°C) at 10,000 feet

(3,048 meters).

Operating:

0° to 60°C (32° to 140°F)

Nonoperating:

–40° to 70°C (–40° to 158°F)

2.9.2

Temperature gradient

Operating:

20°C per hour (68°F per hour max), without condensation

30°C per hour (86°F per hour max)

Nonoperating:

2.9.3

2.9.3.1

Humidity

Relative humidity

Operating:

Nonoperating:

5% to 90% noncondensing (30% per hour max)

5% to 95% noncondensing (30% per hour max)

2.9.3.2

Wet bulb temperature

Operating:

37.7°C (99.9°F max)

40°C (104°F max)

Nonoperating:

2.9.4

Altitude

Operating:

–60.96 m to 3,048 m (–200 ft. to 10,000+ ft.)

–60.96 m to 12,192 m (–200 ft. to 40,000+ ft.)

Nonoperating:

Barracuda 7200.8 PATA Product Manual, Rev. F

2.9.5

Shock

All shock specifications assume that the drive is mounted securely with the input shock applied at the drive

mounting screws. Shock may be applied in the X, Y or Z axis.

2.9.5.1

Operating shock

These drives comply with the performance levels specified in this document when subjected to a maximum

operating shock of 63 Gs based on half-sine shock pulses of 2 msec. Shocks should not be repeated more

than two times per second.

2.9.5.2

Nonoperating shock

The nonoperating shock level that the drive can experience without incurring physical damage or degradation

in performance when subsequently put into operation is 300 Gs based on a nonrepetitive half-sine shock pulse

of 2 msec duration.

2.9.6

Vibration

All vibration specifications assume that the drive is mounted securely with the input vibration applied at the

drive mounting screws. Vibration may be applied in the X, Y or Z axis.

2.9.6.1

Operating vibration

The following table lists the maximum vibration levels that the drive may experience while meeting the perfor-

mance standards specified in this document.

5–22 Hz

Limited displacement

0.5 G acceleration

23–350 Hz

2.9.6.2

Nonoperating vibration

The following table lists the maximum nonoperating vibration that the drive may experience without incurring

physical damage or degradation in performance when subsequently put into operation.

5–22 Hz

Limited displacement

5.0 Gs

23–350 Hz

Barracuda 7200.8 PATA Product Manual, Rev. F

2.10

Acoustics

Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). All mea-

surements are consistent with ISO document 7779. Sound power measurements are taken under essentially

free-field conditions over a reflecting plane. For all tests, the drive is oriented with the cover facing upward.

Note. For seek mode tests, the drive is placed in seek mode only. The number of seeks per second is defined

by the following equation:

(Number of seeks per second = 0.4 / (average latency + average access time)

Table 5:

Fluid Dynamic Bearing (FDB) motor acoustics

Acoustic mode

Idle*

Performance seek

2.8 bels (typ)

3.4 bels (max)

3.7 bels (typ)

3.9 bels (max)

*During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and

power to operational levels.

2.11

Electromagnetic immunity

When properly installed in a representative host system, the drive operates without errors or degradation in

performance when subjected to the radio frequency (RF) environments defined in the following table:

Table 6:

Radio frequency environments

Performance

level

Reference

standard

Test

Description

Electrostatic discharge

Radiated RF immunity

Contact, HCP, VCP: ± 4 kV; Air:

± 8 kV

EN 61000-4-2: 95

80 to 1,000 MHz, 3 V/m,

80% AM with 1 kHz sine

900 MHz, 3 V/m, 50% pulse

modulation @ 200 Hz

EN 61000-4-3: 96

ENV 50204: 95

Electrical fast transient

Surge immunity

± 1 kV on AC mains, ± 0.5 kV on

external I/O

EN 61000-4-4: 95

EN 61000-4-5: 95

EN 61000-4-6: 97

EN 61000-4-11: 94

± 1 kV differential, ± 2 kV com-

mon, AC mains

Conducted RF immunity

Voltage dips, interrupts

150 kHz to 80 MHz, 3 Vrms,

80% AM with 1 kHz sine

0% open, 5 seconds

0% short, 5 seconds

40%, 0.10 seconds

70%, 0.01 seconds

Barracuda 7200.8 PATA Product Manual, Rev. F

2.12

Reliability

Nonrecoverable read errors

Annualized Failure Rate (AFR)

Contact start-stop cycles

1 per 10 bits read, max.

0.34% (nominal power, 25°C ambient temperature)

50,000 cycles

(at nominal voltage and temperature, with 60 cycles per hour and a 50% duty cycle)

Service Life

Warranty

5 Years

5 years on distribution units.

To determine the warranty for a specific drive, use a web browser to access the fol-

lowing web page:

www.seagate.com/support/service/

From this page, click on the “Verify Your Warranty” link. You will be asked to provide

the drive serial number, model number (or part number) and country of purchase.

The system will display the warranty information for your drive.

Preventive maintenance

None required

2.13

Agency certification

2.13.1

Safety certification

The drives are recognized in accordance with UL 1950 and CSA C22.2 (950) and meet all applicable sections

of IEC950 and EN 60950 as tested by TUV North America.

2.13.2

Electromagnetic compatibility

Hard drives that display the CE mark comply with the European Union (EU) requirements specified in the Elec-

tromagnetic Compatibility Directive (89/336/EEC). Testing is performed to the levels specified by the product

standards for Information Technology Equipment (ITE). Emission levels are defined by EN 55022, Class B and

the immunity levels are defined by EN 55024.

Seagate uses an independent laboratory to confirm compliance with the EC directives specified in the previous

paragraph. Drives are tested in representative end-user systems. Although CE-marked Seagate drives comply

with the directives when used in the test systems, we cannot guarantee that all systems will comply with the

directives. The drive is designed for operation inside a properly designed enclosure, with properly shielded I/O

cable (if necessary) and terminators on all unused I/O ports. Computer manufacturers and system integrators

should confirm EMC compliance and provide CE marking for their products.

Korean RRL

If these drives have the Korea Ministry of Information and Communication (MIC) logo, they comply with para-

graph 1 of Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic

Compatibility (EMC) Framework requirements of the Radio Research Laboratory (RRL) Ministry of Information

and Communication Republic of Korea.

Barracuda 7200.8 PATA Product Manual, Rev. F

These drives have been tested and comply with the Electromagnetic Interference/Electromagnetic Susceptibil-

ity (EMI/EMS) for Class B products. Drives are tested in a representative, end-user system by a Korean-recog-

nized lab.

• EUT name (model numbers): ST3400832A, ST3400632A, ST3360832A, ST3300831A, ST3300631A,

ST3250823A, ST3250623A and ST3200826A.

• Certificate numbers:

ST3400832A

ST3400632A

ST3300831A

ST3300631A

ST3250823A

ST3250623A

ST3200826A

E-H011-04-4534 (B)

E-H011-04-4533 (B)

• Trade name or applicant: Seagate Technology

• Manufacturing date: November 2004

• Manufacturer/nationality: Singapore and China

Australian C-Tick (N176)

If these models have the C-Tick marking, they comply with the Australia/New Zealand Standard AS/NZS3548

1995 and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Australian Communi-

cation Authority (ACA).

2.13.3

FCC verification

These drives are intended to be contained solely within a personal computer or similar enclosure (not attached

as an external device). As such, each drive is considered to be a subassembly even when it is individually mar-

keted to the customer. As a subassembly, no Federal Communications Commission verification or certification

of the device is required.

Seagate Technology LLC has tested this device in enclosures as described above to ensure that the total

assembly (enclosure, disc drive, motherboard, power supply, etc.) does comply with the limits for a Class B

computing device, pursuant to Subpart J, Part 15 of the FCC rules. Operation with noncertified assemblies is

likely to result in interference to radio and television reception.

Radio and television interference. This equipment generates and uses radio frequency energy and if not

installed and used in strict accordance with the manufacturer’s instructions, may cause interference to radio

and television reception.

This equipment is designed to provide reasonable protection against such interference in a residential installa-

tion. However, there is no guarantee that interference will not occur in a particular installation. If this equipment

does cause interference to radio or television, which can be determined by turning the equipment on and off,

you are encouraged to try one or more of the following corrective measures:

• Reorient the receiving antenna.

• Move the device to one side or the other of the radio or TV.

• Move the device farther away from the radio or TV.

• Plug the computer into a different outlet so that the receiver and computer are on different branch outlets.

If necessary, you should consult your dealer or an experienced radio/television technician for additional sug-

gestions. You may find helpful the following booklet prepared by the Federal Communications Commission:

How to Identify and Resolve Radio-Television Interference Problems. This booklet is available from the Super-

intendent of Documents, U.S. Government Printing Office, Washington, DC 20402. Refer to publication num-

ber 004-000-00345-4.

Barracuda 7200.8 PATA Product Manual, Rev. F

2.14

Environmental protection

Seagate designs its products to meet environmental protection requirements worldwide, including regulations

restricting certain chemical substances.

European Union Restriction of Hazardous Substances (RoHS)

The European Union Restriction of Hazardous Substances (RoHS) Directive restricts the presence of chemical

substances, including Lead (Pb), in electronic products effective July 2006. Although amendments to the Euro-

pean Union’s Restriction of Hazardous Substances (RoHS) Directive have not been finalized, to the best of our

knowledge the disc drives documented in this publication will comply with the final RoHS Directive require-

ments.

A number of parts and materials in Seagate products are procured from external suppliers. We rely on the rep-

resentations of our suppliers regarding the presence of RoHS substances in these parts and materials. Our

supplier contracts require compliance with our chemical substance restrictions, and our suppliers document

their compliance with our requirements by providing material content declarations for all parts and materials for

the disc drives documented in this publication. Current supplier declarations include disclosure of the inclusion

of any RoHS-regulated substance in such parts or materials.

Seagate also has internal systems in place to ensure ongoing compliance with the RoHS Directive and all laws

and regulations which restrict chemical content in electronic products. These systems include standard operat-

ing procedures that ensure that restricted substances are not utilized in our manufacturing operations, labora-

tory analytical validation testing, and an internal auditing process to ensure that all standard operating

procedures are complied with.

2.15

Corrosive environment

Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure to

light industrial environments containing sulfurous gases, chlorine and nitric oxide, classes G and H per ASTM

B845. However, this accelerated testing cannot duplicate every potential application environment. Users

should use caution exposing any electronic components to uncontrolled chemical pollutants and corrosive

chemicals as electronic drive component reliability can be affected by the installation environment. The silver,

copper, nickel and gold films used in Seagate products are especially sensitive to the presence of sulfide, chlo-

ride, and nitrate contaminants. Sulfur is found to be the most damaging. In addition, electronic components

should never be exposed to condensing water on the surface of the printed circuit board assembly (PCBA) or

exposed to an ambient relative humidity greater than 95%. Materials used in cabinet fabrication, such as vulca-

nized rubber, that can outgas corrosive compounds should be minimized or eliminated. The useful life of any

electronic equipment may be extended by replacing materials near circuitry with sulfide-free alternatives.

Barracuda 7200.8 PATA Product Manual, Rev. F

3.0

Configuring and mounting the drive

This section contains the specifications and instructions for configuring and mounting the drive.

3.1

Handling and static discharge precautions

After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic dis-

charge (ESD) hazards. Observe the following standard handling and static-discharge precautions:

Caution:

• Before handling the drive, put on a grounded wrist strap, or ground yourself frequently by touching the metal

chassis of a computer that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the

entire installation procedure.

• Handle the drive by its edges or frame only.

• The drive is extremely fragile—handle it with care. Do not press down on the drive top cover.

• Always rest the drive on a padded, antistatic surface until you mount it in the computer.

• Do not touch the connector pins or the printed circuit board.

• Do not remove the factory-installed labels from the drive or cover them with additional labels. Removal voids

the warranty. Some factory-installed labels contain information needed to service the drive. Other labels are

used to seal out dirt and contamination.

Barracuda 7200.8 PATA Product Manual, Rev. F

3.2

Breather filter hole precautions

This section contains information regarding the precautions which should be taken regarding the breather filter

hole in Seagate hard disc drives. Proper precautions should be taken to ensure full functionality and prevent

possible damage to the drive.

Breather hole

Do not cover or seal

this hole.

Figure 3

Breather filter hole location

Caution: Do not cover, seal, or insert any object into this hole.

This hole has two purposes:

• To allow condensation inside the hard disc to escape

• To allow air pressure inside the hard disc to equalize with ambient pressure

Note. If this hole is covered, sealed, or penetrated by any object, the drive reliability may be compromised

and could lead to permanent damage. Covering or sealing this hole voids the warranty.

Barracuda 7200.8 PATA Product Manual, Rev. F

3.3

Jumper settings

3.3.1

Master/slave configuration

The options jumper block shown in Figure 4 is used to configure the drive for operation. It is the 8-pin dual

header between the interface connector and the power connector. Use the following settings to configure the

drive as a master or a slave.

Master or single drive. The drive is configured at the factory for a master or single-drive operation with a

jumper set on pins 7 and 8.

Drive as slave. Remove all jumpers.

Drive as master with a non-ATA-compatible slave.

Use this jumper setting only if the drive does not work as a master with no jumpers installed.

Options jumper block

Master or single drive

Drive is slave

Master with non ATA-

compatible slave

Cable select

Limit drive capacity

to 32 Gbytes

Circuit Board

Figure 4

Master/slave jumper settings

3.3.2

Cable-select option

Computers that use cable select determine the master and slave drives by selecting or deselecting pin 28,

CSEL, on the interface bus. Master and slave drives are determined by their physical position on the cable. To

enable cable select, set a jumper on pins 5 and 6 as shown in Figure 4. Refer to your computer manual to

determine whether your computer supports this option.

3.3.3

Alternate capacity jumper

Some older computers may “hang” at startup if their BIOS detects a disc drive with a capacity greater than 32

Gbytes. This limits the drive’s capacity to 32 Gbytes when the alternate capacity jumper is used. To access the

full capacity of the drive, you can:

• Update the BIOS

• Use third-party software such as DiscWizard^™or Disk Manager

• Use a third-party host adapter

For drives with capacities greater than 32 Gbytes, the alternate capacity jumper changes the total available

LBA sectors to 32 Gbytes to solve issues with some BIOS during power on. The ATA Set Features subcom-

mand “F1 Report Full Capacity Available” causes Identify Data words 60 and 61 to report the full capacity.

See Section 4.1.3 on page 33 for more details on the Set Features command.

Windows XP, Windows Me, Windows 98 or newer versions are needed to support drives with capacities

greater than 32 Gbytes.

Barracuda 7200.8 PATA Product Manual, Rev. F

3.3.4

Ultra ATA/100 cable

An 80-conductor 40-pin cable is required to run Ultra DMA mode 3, mode 4, and mode 5. This cable uses

even-numbered conductors connected to the ground pins to improve signal integrity.

Note.

If you are using a 40-pin, 80-conductor

cable, attach the blue connector to the

motherboard, the black connector to the

master drive, and the gray connector

to the slave.

Master

Slave

Pin 1

Computer

Motherboard

Figure 5

Ultra ATA cable connectors

Note. The drive supports both host and drive cable detection. The host detects the 80-conductor cable by

sampling pin 34, CBLID–, on the interface bus. The drive detects the 80-conductor cable by sens-

ing a capacitor at the host side through the CBLID– signal. The result is reported in a Fast Rise

Detected bit (bit 13 of word 93 in the Identify drive parameter block).

3.4

Drive mounting

You can mount the drive in any orientation using four screws in the side-mounting holes or four screws in the

bottom-mounting holes. See Figure 6 for drive mounting dimensions. Follow these important mounting precau-

tions when mounting the drive:

• Allow a minimum clearance of 0.030 inches (0.76 mm) around the entire perimeter of the drive for cooling.

• Use only 6-32 UNC mounting screws.

• Do not overtighten the mounting screws (maximum torque: 6 inch-lb.).

• Do not use a drive interface cable that is more than 18 inches long.

Barracuda 7200.8 PATA Product Manual, Rev. F

Notes:

1. Dimensions are shown in inches (mm).

2 Dimensions per SFF-8301 specification.

0.228

(5.79)

0.178

(4.27)

2.23

(56.56)

1.028 max

(26.11)

2.83

(71.80)

3 x 0.25 0.010

(6.35 0.037)

both sides

3.71

(94.35)

1.122 0.02

(28.5 0.51)

1.625 0.020

(41.28 0.51)

1.638 0.01

(41.61 0.25)

5.787 max

(146.99)

1.75 0.01

(44.45 0.25)

4.0 0.01

(101.60 0.25)

4 x 6-32 UNC-2B

0.150 (3.81) max. fastener

penetration. 3 threads

minimum engagement.

3 x 6-32 UNC-2B

0.125 0.01

(3.18 0.25)

0.150 (3.81) max. fastener

penetration both sides. 3 threads

minimum engagement.

Recommended

case temperature

measurement location

case temperature

measurement location

3.750 0.01

(95.25 0.25)

4.0 0.01

(101.60 0.25)

Figure 6

Mounting dimensions—top, side and end view

Barracuda 7200.8 PATA Product Manual, Rev. F

4.0

ATA interface

These drives use the industry-standard ATA task file interface that supports 16-bit data transfers. It supports

ATA programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–5. The

drive also supports the use of the IORDY signal to provide reliable high-speed data transfers.

You can use a daisy-chain cable to connect two drives to a single AT host bus. For detailed information about

the ATA interface, refer to the draft of AT Attachment with Packet Interface Extension (ATA/ATAPI-7), NCITS

T13 1410D, subsequently referred to as the Draft ATA-7 Standard.

4.1

ATA interface signals and connector pins

Figure 7 on page 27 summarizes the signals on the ATA interface connector that the drive supports. For a

detailed description of these signals, refer to the Draft ATA-7 Standard.

Drive pin #

Host pin # and signal description

Signal name

–

Reset

Hardware Reset

Ground

DD7

Host Data Bus Bit 7

Host Data Bus Bit 8

Host Data Bus Bit 6

Host Data Bus Bit 9

Host Data Bus Bit 5

Host Data Bus Bit 10

Host Data Bus Bit 4

DD8

DD6

DD9

DD5

DD10

DD4

DD11

DD3

10 Host Data Bus Bit 11

11 Host Data Bus Bit 3

12 Host Data Bus Bit 12

13 Host Data Bus Bit 2

14 Host Data Bus Bit 13

15 Host Data Bus Bit 1

16 Host Data Bus Bit 14

17 Host Data Bus Bit 0

18 Device Data (15:0)

19 Ground

DD12

DD2

DD13

DD1

DD14

DD0

DD15

Ground

(removed)

DMARQ

Ground

DIOW–

STOP

Ground

(No Pin)

21 DMA Request

22 Ground

23 Device I/O Write:

Stop Ultra DMA Burst

24 Ground

DIOR

–

25 Device I/O Read:

Host Ultra DMA Ready:

Host Ultra DMA Data Strobe

26 Ground

27 I/O Channel Ready

Device Ultra DMA Ready

Device Ulta DMA Data Strobe

28 Cable Select

29 DMA Acknowledge

30 Ground

31 Device Interrupt

32 Reserved

33 Host Address Bus Bit 1

34 Passed Diagnostics

Cable Assembly Type Identifier

35 Device Address (2:0)

36 Device Address (2:0)

37 Chip Select (1:0)

38 Chip Select (1:0)

39 Drive Active/Slave Present

40 Ground

HDMARDY

–

HSTROBE

Ground

IORDY

DDMARDY–

DSTROBE

CSEL

–

DMACK

Ground

INTRQ

–

IOCS16

DA1

PDIAG

–

CBLID–

DA0

DA2

CS0

CS1

–

DASP

Ground

Pins 28, 34 and 39 are used for master-slave communication (details shown below).

Drive 1 (slave)

Drive 0 (master)

Host

CSEL

–

PDIAG

DASP–

Figure 7

I/O pins and supported ATA signals

Barracuda 7200.8 PATA Product Manual, Rev. F

4.1.1

Supported ATA commands

The following table lists ATA-standard commands that the drive supports. For a detailed description of the ATA

commands, refer to the Draft ATA-7 Standard. See “S.M.A.R.T . c ommands” on page 33 for details and sub-

commands used in the S.M.A.R.T. implementation.

Table 7:

Supported ATA commands

Command name

Command code (in hex)

98 or E5

Check Power Mode

Device Configuration Freeze Lock

Device Configuration Identify

Device Configuration Restore

Device Configuration Set

Device Reset

B1 / C1

B1 / C2

B1 / C0

B1 / C3

Download Microcode

Execute Device Diagnostics

Flush Cache

Flush Cache Extended

Format Track

Identify Device

Idle

97 or E3

Idle Immediate

95 or E1

Initialize Device Parameters

Read Buffer

Read DMA

Read DMA Extended

Read DMA Without Retries

Read Log Ext

Read Multiple

Read Multiple Extended

Read Native Max Address

Read Native Max Address Extended

Read Sectors

Read Sectors Extended

Read Sectors Without Retries

Read Verify Sectors

Read Verify Sectors Extended

Read Verify Sectors Without Retries

Recalibrate

Security Disable Password

Security Erase Prepare

Barracuda 7200.8 PATA Product Manual, Rev. F

Command name

Security Erase Unit

Security Freeze

Security Set Password

Security Unlock

Seek

Command code (in hex)

Set Features

Set Max Address

Note: Individual Set Max Address

commands are identified by the value

placed in the Set Max Features regis-

ter as defined to the right.

Address:

Password:

Lock:

Unlock:

Freeze Lock:

Set Max Address Extended

Set Multiple Mode

Sleep

99 or E6

S.M.A.R.T. Disable Operations

S.M.A.R.T. Enable/Disable Autosave

S.M.A.R.T. Enable Operations

S.M.A.R.T. Execute Offline

S.M.A.R.T. Read Attribute Thresholds

S.M.A.R.T. Read Data

S.M.A.R.T. Read Log Sector

S.M.A.R.T. Return Status

S.M.A.R.T. Save Attribute Values

S.M.A.R.T. Write Log Sector

Standby

B0 / D9

B0 / D2

B0 / D8

B0 / D4

B0 / D1

B0 / D0

B0 / D5

B0 / DA

B0 / D3

B0 / D6

96 or E2

Standby Immediate

94 or E0

Write Buffer

Write DMA

Write DMA Extended

Write DMA Without Retries

Write Log Extended

Write Multiple

Write Multiple Extended

Write Sectors

Write Sectors Without Retries

Write Sectors Extended

Barracuda 7200.8 PATA Product Manual, Rev. F

4.1.2

Identify Device command

The Identify Device command (command code EC ) transfers information about the drive to the host following

power up. The data is organized as a single 512-byte block of data, whose contents are shown in the T a ble 7

on page 28. All reserved bits or words should be set to zero. Parameters listed with an “x” are drive-specific or

vary with the state of the drive. See Section 2.0 on page 3 for default parameter settings.

The following commands contain drive-specific features that may not be included in the Draft ATA-7 Standard.

Word

Description

Value

Configuration information:

• Bit 15: 0 = ATA; 1 = ATAPI

• Bit 7: removable media

• Bit 6: removable controller

• Bit 0: reserved

0C5A

Number of logical cylinders

16,383

ATA-reserved

0000

Number of logical heads

Retired

0000

Retired

Number of logical sectors per logical track: 63

Retired

003F

7–9

10–19

0000

Serial number: (20 ASCII characters, 0000 = none)

ASCII

Retired

Obsolete

0000

0400

0000

x.xx

23–26

Firmware revision (8 ASCII character string, padded with blanks to end

of string)

27–46

Drive model number

(40 ASCII characters, padded with blanks to end of string)

ST3400832A

ST3400632A

ST3300831A

ST3300631A

ST3250823A

ST3250623A

ST3200826A

(Bits 7–0) Maximum sectors per interrupt on Read multiple and Write

multiple (16)

8010

Reserved

0000

Standard Standby timer, IORDY supported and may be disabled

ATA-reserved

2F00

0000

0200

0007

PIO data-transfer cycle timing mode

Retired

Words 54–58, 64–70 and 88 are valid

Number of current logical cylinders

Number of current logical heads

Number of current logical sectors per logical track

Current capacity in sectors

xxxx

57–58

Barracuda 7200.8 PATA Product Manual, Rev. F

Word

Description

Value

xxxx

Number of sectors transferred during a Read Multiple or Write Multiple

command

60–61

Total number of user-addressable LBA sectors available

(see Section 2.2 for related information)

0FFFFFFFh*

*Note: The maximum value allowed in this field is: 0FFFFFFFh

(268,435,455 sectors, 137 Gbytes). Drives with capacities over 137

Gbytes will have 0FFFFFFFh in this field and the actual number of user-

addressable LBAs specified in words 100-103. This is required for

drives that support the 48-bit addressing feature.

Retired

0000

Multiword DMA active and modes supported

(see note following this table)

xx07

Advanced PIO modes supported (modes 3 and 4 supported)

Minimum multiword DMA transfer cycle time per word (120 nsec)

Recommended multiword DMA transfer cycle time per word (120 nsec)

Minimum PIO cycle time without IORDY flow control (240 nsec)

Minimum PIO cycle time with IORDY flow control (120 nsec)

ATA-reserved

0003

0078

00F0

0078

0000

69–74

Queue depth

76–79

SATA-specific

xxxx

Major version number

007E

Minor version number

0000

Command sets supported

346B

Command sets supported

7D01

Command sets support extension

Command sets enabled

4003

34xx

Command sets enabled

3xxx

Command sets enable extension

4003

Ultra DMA support and current mode

(see note following this table)

xx3F

Security erase time

0000

Enhanced security erase time

Master password revision code

Hardware reset value (see description following this table)

ATA-reserved

FFFE

xxxx

95–99

100–103

0000

Total number of user-addressable LBA sectors available (see Section

2.2 for related information). These words are required for drives that

support the 48-bit addressing feature. Maximum value:

0000FFFFFFFFFFFFh.

ST3400832A = 781,422,768

ST3400632A = 781,422,768

ST3300831A = 586,072,368

ST3300631A = 586,072,368

ST3250823A = 488,397,168

ST3250623A = 488,397,168

ST3200826A = 390,721,968

104–127

ATA-reserved

0000

Barracuda 7200.8 PATA Product Manual, Rev. F

Word

128

Description

Value

Security status

Seagate-reserved

ATA-reserved

Integrity word

0001

129–159

160–254

255

xxxx

0000

xxA5

Note. Advanced Power Management (APM) and Automatic Acoustic Management (AAM) features are not supported

Note. See the bit descriptions below for words 63, 88, and 93 of the Identify Drive data:

Description (if bit is set to 1)

Bit

Word 63

Multiword DMA mode 0 is supported.

Multiword DMA mode 1 is supported.

Multiword DMA mode 2 is supported.

Multiword DMA mode 0 is currently active.

Multiword DMA mode 1 is currently active.

Multiword DMA mode 2 is currently active.

Word 88

Bit

Ultra DMA mode 0 is supported.

Ultra DMA mode 1 is supported.

Ultra DMA mode 2 is supported.

Ultra DMA mode 3 is supported.

Ultra DMA mode 4 is supported.

Ultra DMA mode 5 is supported.

Ultra DMA mode 0 is currently active.

Ultra DMA mode 1 is currently active.

Ultra DMA mode 2 is currently active.

Ultra DMA mode 3 is currently active.

Ultra DMA mode 4 is currently active.

Ultra DMA mode 5 is currently active.

Word 93

Bit

1 = 80-conductor cable detected, CBLID above V^IH

0 = 40-conductor cable detected, CBLID below VIL

Barracuda 7200.8 PATA Product Manual, Rev. F

4.1.3

Set Features command

This command controls the implementation of various features that the drive supports. When the drive receives

this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an inter-

rupt. If the value in the register does not represent a feature that the drive supports, the command is aborted.

Power-on default has the read look-ahead and write caching features enabled. The acceptable values for the

Features register are defined as follows:

Enable write cache (default).

Set transfer mode (based on value in Sector Count register).

Sector Count register values:

Set PIO mode to default (PIO mode 2).

Set PIO mode to default and disable IORDY (PIO mode 2).

PIO mode 0

PIO mode 1

PIO mode 2

PIO mode 3

PIO mode 4 (default)

Multiword DMA mode 0

Multiword DMA mode 1

Multiword DMA mode 2

Ultra DMA mode 0

Ultra DMA mode 1

Ultra DMA mode 2

Ultra DMA mode 3

Ultra DMA mode 4

Ultra DMA mode 5

Disable read look-ahead (read cache) feature.

Disable write cache.

Enable read look-ahead (read cache) feature (default).

Report full capacity available

Note. At power-on, or after a hardware or software reset, the default values of the features are as indi-

cated above.

4.1.4

S.M.A.R.T. commands

S.M.A.R.T. provides near-term failure prediction for disc drives. When S.M.A.R.T. is enabled, the drive moni-

tors predetermined drive attributes that are susceptible to degradation over time. If self-monitoring determines

that a failure is likely, S.M.A.R.T. makes a status report available to the host. Not all failures are predictable.

S.M.A.R.T. predictability is limited to the attributes the drive can monitor. For more information on S.M.A.R.T.

commands and implementation, see the Draft ATA-7 Standard.

SeaTools diagnostic software activates a built-in drive self-test (DST S.M.A.R.T. command for D4 ) that elimi-

nates unnecessary drive returns. The diagnostic software ships with all new drives and is also available at:

http://seatools.seagate.com.

Barracuda 7200.8 PATA Product Manual, Rev. F

This drive is shipped with S.M.A.R.T. features disabled. You must have a recent BIOS or software package that

supports S.M.A.R.T. to enable this feature. The table below shows the S.M.A.R.T. command codes that the

drive uses.

Codeinfeatures

S.M.A.R.T. command

S.M.A.R.T. Read Data

S.M.A.R.T. Enable/Disable Attribute Autosave

S.M.A.R.T. Save Attribute Values

S.M.A.R.T. Execute Off-line Immediate (runs DST)

S.M.A.R.T. Read Log Sector

S.M.A.R.T. Write Log Sector

S.M.A.R.T. Enable Operations

S.M.A.R.T. Disable Operations

S.M.A.R.T. Return Status

Note. If an appropriate code is not written to the Features Register, the command is aborted and 0x04

(abort) is written to the Error register.

Barracuda 7200.8 PATA Product Manual, Rev. F

5.0

Seagate Technology support services

Internet

For information regarding Seagate products and services, visit www.seagate.com. Worldwide support is

available 24 hours daily by email for your questions.

Presales Support:

[email protected]

Technical Support:

[email protected]

Warranty Support:

http://www.seagate.com/support/service/index.html

mySeagate

my.seagate.com is the industry's first Web portal designed specifically for OEMs and distributors. It provides

self-service access to critical applications, personalized content and the tools that allow our partners to

manage their Seagate account functions. Submit pricing requests, orders and returns through a single,

password-protected Web interface-anytime, anywhere in the world.

spp.seagate.com

spp.seagate.com supports Seagate resellers with product information, program benefits and sales tools. You

may register for customized communications that are not available on the web. These communications contain

product launch, EOL, pricing, promotions and other channel-related information. To learn more about the

benefits or to register, go to spp.seagate.com, any time, from anywhere in the world.

Seagate Service Centers

Presales Support

Our Presales Support staff can help you determine which Seagate products are best suited for your specific

application or computer system, as well as product availability and compatibility.

Technical Support

Seagate technical support is available to assist you online at support.seagate.com or through one of our call

centers. Have your system configuration information and your “ST” model number available.

SeaTDD™ (+1-405-324-3655) is a telecommunications device for the deaf (TDD). You can send questions or

comments 24 hours daily and exchange messages with a technical support specialist during normal business

hours for the call center in your region.

Barracuda 7200.8 PATA Product Manual, Rev. F

Customer Service Operations

Warranty Service

Seagate offers worldwide customer support for Seagate products. Seagate distributors, OEMs and other direct

customers should contact their Seagate Customer Service Operations (CSO) representative for warranty-

related issues. Resellers or end users of drive products should contact their place of purchase or Seagate

warranty service for assistance. Have your serial number and model or part number available.

Data Recovery Services

Seagate offers data recovery services for all formats and all brands of storage media. Our data recovery

services labs are currently located throughout the world. . Additional information, including an online request

form and data loss prevention resources, is available at http://services.seagate.com/index.aspx

Authorized Service Centers

Seagate Service Centers are available on a global basis for the return of defective products. Contact your

customer support representative for the location nearest you.

USA/Canada/Latin America support services

For an extensive list of telephone numbers to technical support, presales and warranty service in USA/

Canada/Latin America, including business hours, go to the "Contact Us" page on www.seagate.com.

Global Customer Support

Presales, Technical, and Warranty Support

Call Center

USA, Canada,

and Mexico

Toll-free

Direct dial

1-800-SEAGATE

+1-405-324-4700

Data Recovery Services

Call Center

Toll-free

Direct dial

FAX

USA, Canada,

and Mexico

1-800-475-01435

+1-905-474-2162

1-800-475-0158

+1-905-474-2459

Europe, the Middle East and Africa Support Services

For an extensive list of telephone numbers to technical support, presales and warranty service in Europe, the

Middle East and Africa, go to the "Contact Us" page on www.seagate.com.

Asia/Pacific Support Services

For an extensive list of telephone numbers to technical support, presales and warranty service in Asia/Pacific,

go to the "Contact Us" page on www.seagate.com.

Barracuda 7200.8 PATA Product Manual, Rev. F

Device Configuration Freeze Lock 28

Device Configuration Identify 28

Device Configuration Restore 28

Device Configuration Set 28

Device Reset 28

diagnostic software 1, 33

DiscWizard 23

Disk Manager 23

Index

acoustics 17

Active mode 14

agency certification (regulatory) 18

alternate capacity jumper 23

altitude 15

ambient conditions 3

ambient temperature 11, 15

areal density 1, 10

dissipation 12

Download Microcode 28

drive diagnostics 11

drive monitoring 1

drive self-test 1, 33

DST 33

ATA interface 27

ATA-standard commands 28

Australian C-Tick 19

autodetection 1

average seek time 11

electrical fast transient 17

electromagnetic compatibility 18

Electromagnetic Compatibility Directive 18

electromagnetic immunity 17

electrostatic discharge 17

EMC compliance 18

EN 60950 18

enclosures 19

environmental specifications 15

EPRML 10

error-correction algorithms 1

errors 18

BIOS 23

BPI 10

breather filter hole precautions 22

buffer 10

burst 1

cable 24

cable select 1

European Union 18

cable-select option 23

cache 1, 10

Execute Device Diagnostics 28

case temperature 15

CE mark 18

failure prediction 33

FCC verification 19

Features register 33

Flush Cache 28

Flush Cache Extended 28

Format Track 28

certification 18

Check Power Mode 28

commands 28

compliance 18

conducted noise 13

conducted RF immunity 17

configuring the drive 21

connector pins 27

connectors 24

contact start-stop cycles 18

Corrosive environment 20

CSA C22.2 (950) 18

CSEL 23

formatted capacity 10

frequency 17

guaranteed sectors 10

C-Tick 19

current profile 13

cycles 18

handling 21

heads 1

height 11

humidity 15

data-transfer rates 1

DC power 12

density 10

I/O data-transfer rate 10

Identify Device 28

Barracuda 7200.8 PATA Product Manual, Rev. F

Identify Device command 30

Idle 12, 28

physical characteristics 11

pins 27

PIO 27

Idle and Standby timers 14

Idle Immediate 28

Idle mode 14

power consumption 12

power dissipation 12

power management 14

power specifications 12

power-management modes 14

Power-on to Ready 11

precautions 24

Idle mode power 12

IEC950 18

Information Technology Equipment 18

Initialize Device Parameters 28

interface 10, 27

interface signals 27

interference 19

interleave 10

internal data-transfer rate OD 10

ISO document 7779 17

preventive maintenance 18

programmable power management 14

radiated RF immunity 17

radio and television interference 19

radio frequency 17

jumper settings 23

random track location 12

Read Buffer 28

Read DMA 28

Korean RRL 18

Read DMA Extended 28

Read DMA without Retries 28

read errors 18

LBA mode 10

length 11

logical geometry 10

Read Log Ext 28

Read Multiple 1, 28

Read Multiple Extended 28

Read Native Max Address 28

Read Native Max Address Extended 28

Read Sectors 28

maintenance 18

master 23

master/slave 1

Master/slave configuration 23

maximum temperature 15

measurement locations 15

modes 27

Read Sectors Extended 28

Read Sectors Without Retries 28

Read Verify Sectors 28

Read Verify Sectors Extended 28

Read Verify Sectors Without Retries 28

read/write power and current 12

Recalibrate 28

monitoring 1

mounting the drive 21, 24

recording and interface technology 10

recording density 10

recording heads 1

recording method 10

relative humidity 15

reliability 18

resistance 13

resistive load 13

noise 13

nominal power 3

nonoperating shock 16

nonoperating vibration 16

nonrecoverable read errors 18

RF 17

RoHS 20

operating 12

operating power and current 12

operating shock 16

operating vibration 16

orientation 24

S.M.A.R.T. commands 33

S.M.A.R.T. Disable Operations 29

S.M.A.R.T. drive monitoring 1

S.M.A.R.T. Enable Operations 29

Barracuda 7200.8 PATA Product Manual, Rev. F

S.M.A.R.T. Enable/Disable Autosave 29

S.M.A.R.T. Execute Offline 29

S.M.A.R.T. Read Attribute Thresholds 29

S.M.A.R.T. Read Data 29

S.M.A.R.T. Read Log Sector 29

S.M.A.R.T. Return Status 29

S.M.A.R.T. Save Attribute Values 29

S.M.A.R.T. Write Log sector 29

safety certification 18

screws 24

temperature gradient 15

timers 14

TMR 1

track density 10

track-to-track seek time 11

TUV North America 18

UL 1950 18

Ultra ATA/100 24

Ultra DMA 24

SeaTools 1, 33

sectors 10

Security Disable Password 28

Security Erase Prepare 28

Security Erase Unit 29

Security Freeze 29

Security Set Password 29

Security Unlock 29

Seek 29

vibration 16

voltage 13

voltage dips, interrupts 17

voltage tolerance 13

seek mode 12

seek time 11

Seeking 12

Service Life 18

servo electronics 12

Set Features 29

Set Features command 33

Set Max Address 29

Set Max Address Extended 29

Set Multiple Mode 29

shock 16

signals 27

single-track seeks 11

slave 23

weight 11

wet bulb temperature 15

width 11

Write Buffer 29

Write DMA 29

Write DMA Extended 29

Write DMA Without Retries 29

Write Log Extended 29

Write Multiple 1, 29

Write Multiple Extended 29

Write Sectors 29

Write Sectors Extended 29

Write Sectors Without Retries 29

Sleep 12, 29

Sleep mode 14

sound 17

specifications 3

spindle speed 10

Spinup 12

spinup power 12

Standby 12, 29

Standby Immediate 29

Standby mode 12, 14

Standby to Ready 11

start/stop times 11

start-stop cycles 18

static-discharge precautions 21

stop times 11

subassembly 19

support services 35

surge immunity 17

technical support services 35

temperature 15

Barracuda 7200.8 PATA Product Manual, Rev. F

Seagate Technology LLC

920 Disc Drive, Scotts Valley, California 95066-4544, USA

Publication Number: 100323825, Rev. F, Printed in U.S.A.

Seagate U8TM FAMILY ST317221A User Manual
Seagate ST9408114A User Manual
Seagate ST3852A User Manual
Seagate Barracuda ST3250620NS User Manual
Samsung SCH R710XKACRI User Manual
Samsung Galaxy Note 2014 SMP6000ZKVXAR User Manual(1)
Rosewill RX81U AT 25A User Manual
Radio Shack 63 987 User Manual
Pioneer DEH P5700MP User Manual
Numark Industries CDN 33 User Manual