Samsung SCH r410 User Manual

SCH-r410 Series  
P O R T A B L E D U A L - M O D E  
M O B I L E  
P H O N E  
User Manual  
Please read this manual before operating your  
phone, and keep it for future reference.  
Licensed by Qualcomm Incorporated under one or more of the following patents:  
U.S. Patent No. 4, 901, 307; 5, 056, 109; 5, 099, 204; 5, 101, 501; 5, 103, 459; 5,  
107, 225; 5, 109, 390.  
Printed in Korea.  
T9 Text Input is licensed by Tegic Communications and is covered by U.S. Pat.  
5,818,437; U.S. Pat. 5,953,541; U.S. Pat. 6,011,554 and other patents pending.  
Openwave® is a registered Trademark of Openwave, Inc.  
RSA® is a registered Trademark RSA Security, Inc.  
Disclaimer of Warranties; Exclusion of Liability  
EXCEPT AS SET FORTH IN THE EXPRESS WARRANTY CONTAINED ON THE  
WARRANTY PAGE ENCLOSED WITH THE PRODUCT, THE PURCHASER TAKES THE  
PRODUCT "AS IS", AND SAMSUNG MAKES NO EXPRESS OR IMPLIED WARRANTY OF  
ANY KIND WHATSOEVER WITH RESPECT TO THE PRODUCT, INCLUDING BUT NOT  
LIMITED TO THE MERCHANTABILITY OF THE PRODUCT OR ITS FITNESS FOR ANY  
PARTICULAR PURPOSE OR USE; THE DESIGN, CONDITION OR QUALITY OF THE  
PRODUCT; THE PERFORMANCE OF THE PRODUCT; THE WORKMANSHIP OF THE  
PRODUCT OR THE COMPONENTS CONTAINED THEREIN; OR COMPLIANCE OF THE  
PRODUCT WITH THE REQUIREMENTS OF ANY LAW, RULE, SPECIFICATION OR  
CONTRACT PERTAINING THERETO. NOTHING CONTAINED IN THE INSTRUCTION  
MANUAL SHALL BE CONSTRUED TO CREATE AN EXPRESS OR IMPLIED WARRANTY  
OF ANY KIND WHATSOEVER WITH RESPECT TO THE PRODUCT. IN ADDITION,  
SAMSUNG SHALL NOT BE LIABLE FOR ANY DAMAGES OF ANY KIND RESULTING  
FROM THE PURCHASE OR USE OF THE PRODUCT OR ARISING FROM THE BREACH OF  
THE EXPRESS WARRANTY, INCLUDING INCIDENTAL, SPECIAL OR CONSEQUENTIAL  
DAMAGES, OR LOSS OF ANTICIPATED PROFITS OR BENEFITS.  
r410.07_AI18_CB_101609_F3  
Table of Contents  
1
Table of Contents  
2
3
Understanding this User Manual  
Section 1: Getting Started  
Topics Covered  
This section explains how to start using your SCH-r410 phone by activating your  
service, setting up your Voicemail, or getting an understanding of how this manual  
is put together.  
Understanding this User Manual  
The chapters of this guide generally follow the same order as the menus and sub-  
menus in your phone. A robust index for quick reference to most features begins on  
Also included is important safety information that you should know before using your  
phone. Most of this information is near the back of the guide, beginning on page  
Notes and tips  
Throughout this guide there is text that is set apart from the rest. These are intended  
to point out important information, quick methods for activating features, to define  
terms, and more. The definitions for these methods are as follows:  
Notes: Explain alternative options within the current feature, menu, or sub-menu.  
Tips: Provide quick or innovative methods for performing functions related to the  
subject at hand.  
Important: Points out important information about the current feature that could  
affect performance, or even damage your phone.  
Getting Started  
4
           
Installing the Battery  
Note: Your phone comes packaged with a partially charged rechargeable standard Li-Ion battery and travel  
adapter.  
Important!: You must fully charge the battery the first time you use your phone, otherwise you could  
damage the battery.  
1. Insert the top end of the battery first, matching  
the gold contacts on the inside of the battery to  
those on the phone.  
2. Press lightly on the bottom end of the battery  
down into the phone until it slips into place.  
3
3. Press lightly down and inward on the  
bottom of the battery cover.  
4
4. Press lightly on the top end of the battery  
down over the battery until it clicks into  
place.  
Remove the Battery  
1. Press and hold the  
key to turn off the phone (if on).  
2. Press down on the battery cover release  
latch (1) and slide the cover (2) toward the  
bottom end of the phone.  
5
     
Charging the Battery  
3. Lift the battery (3) up and away from the phone,  
bottom end first.  
3
Charging the Battery  
Your phone is powered by a rechargeable standard Li-Ion battery. Only use  
Samsung-approved charging devices and batteries. Samsung accessories are  
designed to maximize battery life. Use of other accessories may invalidate your  
warranty and may cause damage.  
Use the Travel Adapter  
The travel adapter included with your phone is a  
convenient, light-weight charger that rapidly  
charges your phone from any 120/220 VAC outlet.  
1. Plug the large end of the Travel Adapter  
into a standard 120 VAC or 220 VAC wall  
outlet.  
Important!: For connection to an electrical supply not located in North America, you must use an adaptor  
of the proper configuration for the power outlet. Use of the wrong adapter could damage your  
phone and void your warranty.  
2. Insert the smaller end of the Travel  
Adapter into the charger/accessory  
connector at the bottom end of your  
Correct  
phone.  
+
Incorrect  
Important!: You must unplug the adapter before removing the battery from the phone during charging to  
avoid damage.  
Getting Started  
6
     
Low battery indicator  
The battery indicator (  
) in the upper-right corner of the display indicates power  
level. Monitor the battery strength and ensure your battery is adequately charged.  
Three bars (  
) indicate a full charge.  
An empty battery icon (  
) indicates a near empty battery.  
A blinking empty battery icon (  
) and a tone sounding indicate you have two to  
three minutes before the battery is too low to operate the phone.  
If you continue to use your phone without charging its battery, the phone will shut  
down.  
Activating Your Phone  
Contact your Wireless Carrier and follow their instructions for obtaining service, if  
necessary. We suggest that you read this guide to fully understand the services your  
phone supports.  
Turning Your Phone On  
1. Press and hold the  
key until the display lights.  
Note: As with any other radio-transmitting device, do not touch the antenna while using your phone as this  
can affect call quality and can cause the phone to operate at a higher power level than is necessary.  
2. The phone begins searching for a network signal.  
3. Once the phone finds a signal, the time, date, and day appear near the top  
of the display.  
4. You’re now ready to place and receive calls.  
Note: If you are outside of your carrier’s coverage or roaming area, the No Service icon (  
) appears at  
the top of the phone’s display. If you cannot place or receive calls, try later when service is available,  
or at another location.  
Turn Your Phone Off  
Press and hold the  
off.  
key for two or more seconds. Your phone powers  
Note: If your phone is on and you press  
for less than one second, the phone will not power off. This  
prevents your phone from being turned off accidentally.  
7
     
Activating Your Phone  
Setting Up Your Voicemail  
Voicemail allows callers to leave voice messages, which can be retrieved any time.  
Note: Once your Voicemail account has been set up, you can use the Voicemail folder (under the Message  
menu) to view details of voice messages in your Voicemail box.  
1. In standby mode, press and hold the  
key, or the  
key, or dial  
your own mobile number to dial Voicemail.  
2. Follow the prompts in the new user tutorial to setup your mail box.  
Listen to Voicemail  
1. In standby mode, press and hold the  
key, or the  
key, or dial  
your own mobile number to dial Voicemail. After connecting, you will hear  
your voice greeting.  
2. You are prompted to enter your password.  
Getting Started  
8
   
Section 2: Understanding Your Phone  
Topics Covered  
This section outlines some key features of your phone. It also describes the screen  
format and the icons that will be displayed when the phone is in use.  
Features of Your Phone  
Domestic and international voice and text messaging service (available on  
participating networks).  
High speed data (CDMA 2000 1x Technology)  
Bluetooth® Wireless Technology  
Global Positioning (GPS) Technology  
PIM Functions  
Picture (MMS) Messaging  
Text (SMS) Messaging  
E-mail Messaging  
QWERTY Keypad  
Built-in VGA Digital Camera  
Voice Dial  
Speakerphone  
** The SCH-r410 supports the wireless handsfree profile and the serial port profile for  
Bluetooth® wireless technology. The SCH-r410 does not support Bluetooth OBEX profiles.  
9
       
Closed View of Your Phone  
Closed View of Your Phone  
1. Earpiece  
18. Volume Key  
2. Display  
17. Power Accessory  
Connector  
16. OK Key  
3. Navigation Key  
4. Left Soft Key  
15. Right Soft Key  
14. CLR Key  
13. Camera Key  
12. END Key  
5. Speakerphone  
OK  
Key  
6. SEND Key  
7. Voicemail Key  
11. Alpha-numeric  
Keys  
10. Voice Recognition  
Key  
8. Special Function  
Keys  
9. Microphone  
Features  
1. Earpiece / Speaker — Lets you hear ringing and alert tones, alarm tones,  
and the other parties to calls.  
2. Display — Indicates the status of your phone, including numbers dialed,  
feature and function screens, status icons, message indicators, signal  
strength, and so on.  
3. Navigation Key — In Menu mode, lets you scroll through the phone menu  
options. In Standby mode, lets you access preset functions.  
4. Left Soft Key — Used to navigate through menus and applications and to  
select the choice indicated at the bottom left corner of the Main LCD.  
5. Speakerphone Key — Lets you enable/disable speakerphone mode.  
Understanding Your Phone  
10  
   
6. SEND Key — Lets you place or receive a call. In standby mode, press the  
key once to access the recent call log.  
7. Voicemail Key — Lets you speed dial your Voicemail account to review  
your voice messages.  
8. Special Function Keys — Enter special characters. Performs various  
functions.  
9. Microphone — Lets the other party to a call hear you clearly when you  
are speaking to them.  
10. Voice Recognition Key — In standby mode, pressing and holding this key  
launches VoiceSignal options.  
11. Alpha-numeric Keys — Use these keys to enter numbers, letters, and  
characters.  
12. END Key — Ends a call. If you press and hold the END key, the power goes  
On or Off. When you receive an incoming call, press to send the call to  
voicemail.  
13. Camera Key — Launches the Camera feature of your phone.  
14. CLR Key — Deletes characters from the display when you are in text entry  
mode. Press this key to return to the previous menu or screen when  
navigating features on your phone.  
15. Right Soft Key — Used to navigate through menus and applications and  
to select the choice indicated at the bottom right corner of the Main  
Display.  
16. OK Key — Pressing when navigating through a menu accepts the  
highlighted choice in a menu.  
17. Power/Accessory Connector — Used to plug in charging accessories  
and to connect a headset or any available accessory cables to your phone.  
18. Volume Key — Lets you adjust the ring volume in standby mode, adjust  
the voice volume during a call, or mute the ringer during an incoming call.  
11  
Open View (Front) of Your Phone  
Open View (Front) of Your Phone  
1. Volume Key  
19. END Key  
18. Navigation Key  
17. Microphone  
2. Earpiece/  
Speaker  
3. Display  
16. Speakerphone Key  
15. SEND Key  
4. Voicemail Key  
14. Voice Recognition  
Key  
13. CLR Key  
5. Text Function Keys  
12. New Line Key  
11. OK Key  
10. Right Soft Key  
6. Left Soft Key  
9. Arrow Keys  
7. Special Function  
Keys  
8. SPACE Keys  
Features  
1. Volume Key — Lets you adjust the ring volume in standby mode, adjust  
the voice volume during a call, or mute the ringer during an incoming call.  
2. Earpiece / Speaker — Lets you hear ringing and alert tones, alarm tones,  
and the other parties to calls.  
3. Display — Indicates the status of your phone, including numbers dialed,  
feature and function screens, status icons, message indicators, signal  
strength, and so on.  
4. Voicemail Key — Lets you speed dial your Voicemail account to review  
your voice messages.  
5. Text Function Keys — Function (Fn) key toggles text entry mode between  
ABC and 123 modes. SHIFT key toggles ABC mode capitalization between  
ABC, Abc, and abc.  
6. Left Soft Key — Used to navigate through menus and applications and to  
select the choice indicated at the bottom left corner of the Main LCD.  
7. Special Function Keys — Enter special characters. Perform various  
functions.  
8. SPACE Key — Inserts a space character in a text entry.  
9. Arrow Keys — In Menu mode, lets you scroll through the phone menu  
options. In Standby mode, lets you access preset functions and one user-  
defined function.  
Understanding Your Phone  
12  
   
10. Right Soft Key — Used to navigate through menus and applications and  
to select the choice indicated at the bottom right corner of the Main  
Display.  
11. OK Key — Pressing when navigating through a menu accepts the  
highlighted choice in a menu.  
12. New Line Key — In text entry mode, ends the current text line and starts  
a new line.  
13. CLR Key — Deletes characters from the display when you are in text entry  
mode. Press this key to return to the previous menu or screen when  
navigating features on your phone.  
14. Voice Recognition Key — In standby mode, pressing and holding this key  
launches VoiceSignal options.  
15. SEND Key — Lets you place or receive a call. In standby mode, press the  
key once to access the recent call log.  
16. Speakerphone Key — Lets you enable/disable speakerphone mode.  
17. Microphone — Lets the other caller hear you clearly when you are  
speaking to them.  
18. Navigation Key — In Menu mode, lets you scroll through the phone menu  
options. In Standby mode, lets you access preset functions and one user-  
defined function.  
19. END Key — Ends a call. If you press and hold the END key, the power goes  
On or Off. When you receive an incoming call, press to send the call to  
voicemail.  
13  
Closed Rear View of Your Phone  
Closed Rear View of Your Phone  
1. Speaker  
Grill  
7. Camera Key  
6. Battery Cover  
5. Power Accessory  
Connector  
4. Camera Lens  
3. Mirror  
2. Volume Key  
1. Speaker Grill — Lets you hear ringing and alert tones, alarm tones, and  
the other parties to calls.  
2. Volume Key — Lets you adjust the ring volume in standby mode, adjust  
the voice volume during a call, or mute the ringer during an incoming call.  
3. Mirror — Lets you position the Camera Lens to take self portraits.  
4. Camera Lens — The lens of your built-in camera.  
5. Power/Accessory Connector — Used to plug in charging accessories  
and to connect a headset or any available accessory cables to your phone.  
6. Battery Cover — Lets you access your phone’s battery.  
7. Camera Key — Launches the Camera feature of your phone.  
Understanding Your Phone  
14  
 
Command Keys  
Functions for the soft keys are defined by what appears above each in the display.  
There are two soft keys, the Left soft key  
and the Right soft key  
.
Left Soft Key  
Some functions of the Left soft key are as follows.  
In standby mode, press the MENU (left) soft key (  
) to open the main menu.  
When the Left soft key function is Edit, press the Edit (left) soft key (  
) to edit  
a Contact.  
Right Soft Key  
Some functions of the Right soft key are as follows.  
In standby mode, press the @metro (Right) soft key (  
) to launch the @metro  
screen.  
When the Right soft key function is Options, press the Options (right) soft key  
) and a pop-up menu appears.  
(
When the Right soft key function is Back, press the Back (right) soft key (  
) to  
back up one menu level.  
OK Key  
In a menu, press the OK key (  
In camera mode, press the OK key (  
OK  
) to accept the highlighted selection.  
) to take a photo or to create a Picture  
OK  
message.  
When the OK key function is Edit, press the Edit (OK) key (  
OK  
) to edit a Draft  
message.  
Clear Key  
The CLR key (  
display. You can also use the  
) is used to erase or clear numbers, text, or symbols from the  
key to return to a previous menu.  
1. If you enter an incorrect character, briefly press  
to backspace (and  
delete) the character.  
2. To erase the entire sentence, press and hold  
.
3. To back up one menu level, briefly press  
.
15  
           
Understanding the Display Screen  
End Key  
1. Press and hold the End key  
to turn on your phone.  
once to disconnect a call.  
to return to standby mode from any menu, or to cancel the last  
2. Briefly press  
3. Press  
input.  
Send Key  
The Send key  
is used to answer calls, dial calls, and to recall the last  
number(s) dialed, received, or missed.  
1. Press once to answer calls.  
2. Enter a number and briefly press  
to make a call.  
in standby mode to display a list of recent calls to and  
3. Briefly press  
from your phone.  
4. Press  
twice in standby mode to call the most recent number.  
5. Press  
to pick up a waiting call. Press  
again to switch back to  
the other call.  
Navigation Key  
Use the directional keys on the Navigation key  
OK  
to browse menus, sub-  
menus, and lists. Each directional key also acts as a shortcut to launch applications.  
Camera Key  
Use the Camera key (  
) on the right side of the phone to activate the camera  
built into your phone and to take pictures.  
Understanding the Display Screen  
1. The top line of your phone’s display  
contains icons that indicate network  
status, battery power, signal strength,  
connection type, and more.  
1
2
2. The center portion of the display shows  
information such as call progress  
information, messages, and photos.  
3
Understanding Your Phone  
16  
         
3. The bottom line of the display shows current soft key functions. The  
sample screen shows that pressing the Left soft key ( ) will display the  
) will show the @metro  
Main Menu and pressing the Right soft key (  
screen.  
With the QWERTY keypad open, the  
1
display rotates automatically from  
portrait mode (as shown above) to  
landscape mode (as shown here).  
2
Display Screen Icons  
Your SCH-r410 phone can show you  
definitions of the icons that appear  
on the top line of the display.  
3
To access the Icon Glossary:  
In standby mode, press the MENU (left) soft key (  
(for Settings), (for Phone Info), and  
), then press  
for Icon Glossary. A  
list shows of the icons that can appear on the top line of the displays.  
Dialogue Boxes  
Dialogue boxes prompt for action, inform you of status, or warn of situations such as  
low battery. Dialogue boxes and their definitions are outlined below.  
Choice  
Example: “Save Message?”  
Reconfirm  
Example: “Erase All Messages?”  
Performing  
Example: “Sending...” “Connecting...”  
Completed  
Example: “Message Saved”  
Information  
Example: “New Message”  
Error  
Example: “System Error!”  
Warning  
Example: “Low Battery,” “Memory Full!”  
17  
 
Your Phone’s Modes  
Backlights  
Backlights illuminate the display and the keypad. When you press any key or open  
the phone, the backlights come on. They go off when no keys are pressed within a  
period of time set in the Backlight menu.  
Note: During a phone call, the display backlight dims and turns off after 10 seconds to conserve battery  
power, regardless of the Backlight setting.  
See “Backlight” on page 126 for more information.  
Your Phone’s Modes  
Call Answer Mode  
You can choose to answer a call by pressing any key except the  
key or  
key, by pressing only the key, or by opening the phone’s slide. (For more  
Input mode  
Input mode determines how you enter text, numbers, and symbols. While at any text  
entry screen, press the Left soft key (  
), then choose the input mode from the  
pop-up menu using the Navigation key. Optional input modes are T9 Word, Abc,  
ABC, Symbol, and 123. (See “Entering Text” on page 44 for more information.)  
Note: With the QWERTY keypad open, T9 Word is not available. Also, use 123 mode instead of Symbol to  
enter symbols and punctuation in your text.  
Tip: With the phone closed, you can also cycle between T9 Word, Abc, and 123 by repeatedly pressing and  
holding the  
key until the phone beeps.  
Lock Mode  
When the phone is in Lock Mode, restrictions are placed on phone use. You can  
receive calls and messages, but cannot place outgoing calls (except for emergency  
numbers) until you unlock the phone. Lock Mode also restricts access to menus and  
the volume key. Unlock your phone by entering the lock code when prompted. (See  
Keypad Lock Mode  
When the phone is in Keypad Lock Mode, most of the keys are disabled. This  
prevents accidental dialing, when you are carrying the phone. Unlock your phone by  
pressing the Unlock (left) soft key (  
) followed by pressing the  
key.  
Understanding Your Phone  
18  
             
Tip: You can also unlock your phone by opening the QWERTY keypad.  
Note: For more information, see "Auto Key Lock" on page 139..  
Standby Mode  
Standby mode is the state of the phone once it has found service and is idle. The  
phone goes into standby mode:  
After you power the phone on.  
When you press  
after a call or from within a menu.  
In standby mode, you will see the time, day, and date as well as all phone status  
icons.  
Place Calls in Standby Mode  
1. While in standby mode, enter a phone number, and press  
to place a  
call.  
2. Press  
to return to standby mode.  
Receive Messages in Standby Mode  
You can receive messages in standby mode. An alert tone sounds and a notification  
message appears in the display when a new message arrives. The following call  
message options appear:  
View Now — This selection allows you to view the messages now.  
View Later — This selection allows you to view the messages at a later date.  
OK  
Highlight the desired viewing option and then press  
Talk Mode  
You can place and receive calls only when your phone is on. While in a call your  
phone is in talk mode. Press the Options (right) soft key ( ) to display a list of  
.
Speakerphone Mode  
To use your phone handsfree or to share a call with other people nearby, place your  
phone in Speakerphone Mode by pressing and holding the Speakerphone key  
(
) until “Speakerphone On” appears in the display.  
Caution!: Keep the phone away from you ear while in Speakerphone Mode. (For more information, see  
19  
       
Your Phone’s Modes  
To disable Speakerphone Mode, press and hold  
appears in the display.  
until “Speakerphone Off”  
Note: Your phone automatically enters Speakerphone Mode when you dial a call using the QWERTY keypad  
and the called phone begins ringing.  
Enter/Exit Silent Mode  
Silence the tones your keypad makes when you press a key.  
To enter Silent Mode:  
In standby mode, press and hold  
appears in the display and your phone returns to standby mode.  
To exit Silent Mode:  
. “Entering Silent Mode” briefly  
While in Silent mode and standby mode, press and hold  
. “Exit  
Silent Mode” briefly appears in the display and your phone returns to  
standby mode.  
Vibrate Mode  
In standby mode, repeatedly press the volume key ( ) down until Vibrate  
appears in the display.  
The volume key is on the upper right side of phone.  
Adjust the Ringer  
1. In standby mode, press the volume key ( ) on the right side of the phone  
up or down. Options are:  
Ringer Off  
Vibrate  
Low  
Medium  
Medium/High  
High  
Vibrate/High  
Low/Medium  
2. When you are satisfied with the setting, press the  
key. Your phone  
OK  
returns to standby mode.  
Tip: You can also enter the Volume > Voice Calls sub-menu by pressing the MENU (left) soft key (  
then pressing the , and keys. Use the Volume key on the right  
side of your phone to adjust the ringer volume setting.  
),  
,
,
Note: The Vibrate icon (  
) appears in the display when the phone is in Vibrate mode. The Vibrate/  
) appears in the display when the phone is in Vibrate/High mode.  
Ring icon (  
Understanding Your Phone  
20  
           
Camera Mode  
Camera mode lets you activate your phone’s camera to take pictures. In Camera  
mode, you can also adjust the resolution and appearance of your pictures.  
Entering Camera Mode — In standby mode, press the Camera key (  
) —  
on the right side of the phone.  
Exiting Camera Mode — Press the  
key.  
21  
   
Making a Call  
Section 3: Call Functions  
Topics Covered  
This section provides procedures for making and answering calls. This section also  
describes features, such as call logs and call timers, that help you make calls and  
manage your call time.  
Note: Although the procedures in this section are written for the phone keypad, you can also perform these  
procedures using the QWERTY keypad.  
Making a Call  
1. With the phone on, enter the number you wish to call using the keypad.  
2. Press  
to place the call.  
Emergency Calls  
When you call an Emergency Number, such as 911, your SCH-r410 phone locks  
itself in emergency mode, only allowing you to make calls to the emergency call  
center you originally contacted. This enables emergency operators to more easily  
dispatch aid, such as police, fire fighting, and emergency medical personnel.  
1. With the phone on, enter the Emergency Number you wish to call using the  
keypad.  
Note: You can define up to 3 emergency numbers in your phone. (For more information, see "Emergency #"  
2. Press  
to place the call.  
Tip: If you need to make an emergency (911) call with Airplane mode enabled, just dial the emergency  
number and press  
Call Functions  
22  
       
Three-way Calling  
Call two other numbers and connect them to your call using three-way calling.  
1. In standby mode, enter the number for the first party in your call, then  
press  
.
2. When connected, ask the other party to remain on the line. Press  
to  
place them on hold.  
3. Enter the second party’s phone number and press  
.
4. When the second party answers, press  
to connect all three parties.  
Manual Pause Calling  
To manually call a number with pause(s) without storing it in your Contacts list:  
1. In standby mode, enter the number you wish to call.  
2. Press the Options (right) soft key (  
or  
). The following pause  
options appear in the display:  
2-Sec Pause — A 2-second pause after which dialing resumes.  
Wait — A hard pause (waits for input from you).  
3. Use the Up/Down navigation or arrow keys to highlight the desired pause.  
OK  
4. Press the  
key or  
key to enter the highlighted pause into the  
number sequence.  
5. Press to call the number.  
Tip: Press the Save (left) soft key (  
or  
) to store pauses along with the number if you plan to call  
the number frequently.  
Speed Dialing  
Speed Dialing lets you place a call to any Contact stored in your Contacts list by  
dialing the Contact’s Location number.  
1-Touch Dialing  
Use 1-touch dialing to speed dial Contacts from 1 (Voicemail) through 9.  
In standby mode, press and hold the number key corresponding to the  
desired Contact’s speed dial number.  
Example: To speed dial the Contact assigned speed dial 5, press and hold the  
key or the  
key.  
23  
   
Making a Call  
2-Touch Dialing  
Use 2-touch dialing to speed dial Contacts from 10 through 99.  
1. In standby mode, press and release the number key representing the first  
digit of the desired Contact’s speed dial number.  
2. Press and hold the number key representing the second digit of the  
desired Contact’s speed dial number.  
Example: To speed dial the Contact assigned speed dial 35, press  
or  
then press and hold  
the  
key or the  
key.  
3-Touch Dialing  
Use 3-touch dialing to speed dial Contacts from 100 through 999.  
1. In standby mode, press and release the number key representing the first  
digit of the desired Contact’s speed dial number.  
2. Press the number key representing the second digit of the desired  
Contact’s speed dial number.  
3. Press and hold the number key representing the third digit of the desired  
Contact’s speed dial number.  
Example: To speed dial the Contacts entry assigned to speed dial 325, press  
or  
, press  
or  
, then press and hold the  
key or the  
key.  
Voice Dialing  
The voice recognition capabilities of your SCH-r410 are exceptional due to  
advanced, speaker-independent technology. This means you do not need to “train”  
your phone to understand your voice. You can use your voice in a natural manner to  
dial numbers.  
Note: End Calls Before relaunching the VoiceSignal voice recognition software — When you use  
Voice Dialing to make a call, you must end that call before you can use other Voice Commands. See  
“Voice SVC” on page 89 for more information.  
Use the Call command to dial any number stored in your Contacts list by saying the  
name of the contact (Name Dialing). You can also use Call to dial any telephone  
number, even numbers not stored in your contact list, by speaking the individual  
digits in the number (Digit Dialing).  
Call Functions  
24  
 
Voice Dialing Tips:  
Wait for the beep before speaking.  
Speak clearly at a normal volume, as if you were talking to someone on the phone.  
When saying a name, say the first name then the last name.  
Dialing a Name  
To dial a name, do the following:  
1. In standby mode, press and hold the  
key or the  
key.  
Say a Command” appears in the display and is pronounced through the  
earpiece.  
2. Say, “Call”.  
You are prompted to “Say the name or number”.  
3. Speak clearly and say the name of a person in your Contacts list, first  
name followed by last name.  
If the name is recognized, Voice Dial repeats the name and dials the  
number.  
If Voice Dial is not sure which name you said, it displays a choice list of up  
to three names and prompts you with “Did you say?” followed by the first  
name on the list.  
4. Say “Yes” to confirm the name or “No” to hear the next name, or use the  
keypad to select the correct name from the list. (See “Choice Lists” on  
Press the Repeat (right) soft key (  
Press the Settings (left) soft key (  
or  
or  
) to say the name again.  
), then press the Exit right soft  
key (  
or  
) to exit VoiceSignal without dialing.  
If the recognized name has multiple numbers stored for it (that is, Mobile,  
Work, Home, and so on), Voice Dial displays the possible choices and  
prompts you with “Which number?”  
5. Say one of the following number types:  
Home”  
Work”  
Mobile 1”  
Mobile 2”  
Voice Dial dials the specified number.  
25  
Answering a Call  
Dialing a Number  
To dial a number using Voice Dial, do the following:  
1. In standby mode, press and hold the  
key or the  
key.  
Say a Command” appears in the display and is pronounced through the  
speaker.  
2. Say “Call”.  
VoiceSignal prompts you to “Say the name or number.”  
3. Speak clearly and say the telephone number of the person you want to  
call.  
For example, say “7 8 1 9 7 0 5 2 0 0."  
If it recognizes the number, Voice Dial repeats it and dials the number. If  
Voice Dial is not sure it has recognized the number, it displays a choice list  
of up to three numbers and prompts you with “Did you say?” followed by  
the first number on the list.  
4. Say “Yes” to confirm the number or “No” to hear the next one, or use the  
keypad to select the correct number from the list. (See See “Choice Lists”  
Press the Repeat (right) soft key (  
or  
or  
) to say the name again.  
), then press the Exit right soft  
Press the Settings (left) soft key (  
key (  
or  
) to exit VoiceSignal without dialing.  
Pause Dialing From a Contacts Entry  
If you voice dial a contact that contains 2-Sec Pause(s) simply wait for the pauses  
to pass and the dialing to complete.  
If you voice dial a contact that contains Wait(s), wait for the appropriate prompt(s)  
from the number you are calling (credit card number, bank account number, and  
so on) and enter the appropriate response(s).  
Answering a Call  
Incoming  
When you receive a call, the phone displays one of the following:  
If the caller can be identified, the caller’s number (or name if it’s in your Contacts)  
appears in the display.  
If the caller cannot be identified, Call from unavailable #, Call from restricted #,  
or no number appears in the display.  
Call Functions  
26  
     
Tip: Assign pictures to Contacts entries. The entry’s assigned picture appears in the display when you  
The phone continues to notify you of the call until one of the following events occur:  
You answer the call.  
The calling party ends the call.  
The call is sent to voicemail.  
Call Notification Features  
Your phone notifies you of a call in a variety of ways.  
Eight ring volume settings: Ringer Off, Vibrate, Low, Low/Medium, Medium,  
Medium/High, High, or Vibrate/High.  
Different ring types or melodies to distinguish callers.  
Name display with caller ID. (If the caller’s name is programmed into your  
Contacts).  
Information about the last 90 each of incoming, missed, and outgoing calls are  
automatically stored to a call log.  
Set Call Ringer Volume  
1. In standby mode, press the Volume key on the right side of the phone.  
2. Press the Volume key up or down to set the call ringer volume as desired.  
Adjust the Ringer  
1. In standby mode, press the Volume key ( ) on the right side of the phone  
up or down. Options are:  
Ringer Off  
Vibrate  
Low  
Medium  
Medium/High  
High  
Low/Medium  
Vibrate/High  
OK  
2. Press  
once you’re satisfied with the setting. The phone returns to  
standby mode.  
Tip: You can also enter the Volume > Voice Calls sub-menu by pressing the MENU (left) soft key (  
then pressing the , and keys. Use the Volume key on the right side  
of your phone to adjust the ringer volume setting.  
),  
,
,
Note: The Vibrate icon (  
) appears in the display when the call ringer is set to Vibrate. The Vibrate/Ring  
icon ( ) appears in the display when the call ringer is set to Vibrate/High.  
27  
   
Answering a Call  
Call Answer  
Select from two methods for answering calls. This option can be changed in the  
Settings menu.  
1. In standby mode, press the MENU (left) soft key (  
(for Settings), (for Call Settings), and  
), then press  
for Call Answer.  
Tip: You can also carry out this procedure using the QWERTY keypad.  
The following options appear in the display:  
Any Key — Pressing any key except  
Send Key — Only pressing answers a call.  
or  
answers a call.  
2. Use the Up/Down navigation keys to highlight the Call Answer option of  
your choice.  
OK  
3. Press  
to activate the method for answering calls.  
Call Waiting  
If you’re on a call, your phone beeps when another call is incoming. Contact your  
Wireless Carrier for availability.  
1. Press  
to connect and ask the calling party to remain on the line.  
and the second caller is placed on hold and you’re returned to  
2. Press  
the original caller.  
3. Press  
Caller ID  
to alternate between calls.  
Caller ID lets you identify who is calling you by displaying a caller’s number. If the  
caller’s name and number are stored in Contacts, the caller’s name also appears. If  
you’ve assigned a picture to the entry, it appears in the display as well.  
Call Block  
You can prevent your number from displaying on another phone’s caller ID screen by  
enabling Call Block.  
1. In standby mode, enter  
,
,
.
2. Enter the number you wish to call, then press  
.
Silence an Incoming Ring  
During an incoming call, any of the following keys can be pressed to silence the  
ringer:  
The up or down volume key ( ) on the right side of the phone.  
Call Functions  
28  
         
Ignore an Incoming Call  
Ignored calls are immediately forwarded to Voicemail.  
During an incoming call, press the Ignore (right) soft key (  
). The  
incoming call is forwarded to Voicemail.  
In-Use Menu  
You can access a number of menus and features even while in a call.  
1. While in a call, press the Mute/Unmute (left) soft key (  
) to disable/  
enable the microphone.  
2. While in a call, press the Options (right) soft key (  
). The following  
options appear in the display:  
Message — Display the Messages menu.  
Contacts — Display the Contacts menu.  
Recent Calls — View your recent calls log.  
Send DTMF — Send your phone number as DTMF tones to the other person  
on the call.  
Voice Privacy — When set to Enhanced, the phone sounds an audible beep  
when you loose privacy (encryption) on a CDMA connection. For this option to  
work correctly, you must have the Enhanced privacy option enabled in the  
Security settings. (This option is enabled by default.)  
Location Turn your GPS location on or set GPS location for emergency calls  
only.  
Voice Memo — Record this call. Recorded calls are saved to the My Sounds  
3. Within the above menu list, do one of the following:  
OK  
Use the navigation key to highlight a menu or feature. Press the  
the highlighted menu or to activate the highlighted feature.  
key to open  
Press the Cancel (right) soft key (  
) to exit the menu.  
Calls  
Your phone has Call Logs that retain information about Outgoing, Incoming, and  
Missed Calls. The Calls menu lets you access this information for future reference,  
to return calls, and to add new Contacts. You can also view times for your last call  
and the total of all calls.  
Tip: To quickly view a list of your most recent calls (outgoing, incoming, and missed), briefly press the  
key in standby mode. The All Calls screen listing to 270 of your most recent calls appears in the  
display.  
29  
       
Calls  
Outgoing Calls  
The last 90 outgoing calls are stored in the Outgoing calls log. Review the Outgoing  
calls log for the time and date of a call, as well as other information.  
1. In standby mode, press the MENU (left) soft key (  
), then press  
(for Calls) and  
for Outgoing Calls. A list of your outgoing  
calls appears in the display.  
OK  
2. Use the Up and Down navigation keys to highlight a call, then press  
to view further information about the call.  
3. Press the Options (right) soft key (  
). The following options appear in  
the display:  
Save — Save the number to your Contacts.  
Details — Contacts calls only — Lets you view the Contacts entry for the  
recipient of this call.  
Erase — Erase the selected call from your Outgoing call list.  
Lock/Unlock — Blocks/permits erasure of the selected call from your Outgoing  
call list.  
Erase all — Erase all unlocked calls from your Outgoing call list.  
View Timers — Call Timer screen appears in the display listing the number  
and types of calls and their total durations. (See “Call Timer” on page 33 for  
more information.)  
4. Use the Up and Down navigation keys to highlight an option.  
OK  
5. Press  
to perform the highlighted option’s function.  
Incoming Calls  
The last 90 Incoming calls are stored in your phone’s Incoming call log. You can  
review the Incoming call log for time and date of the call, as well as other  
information.  
1. In standby mode, press the MENU (left) soft key (  
), then press  
(for Calls) and for Incoming Calls. A list of your  
Incoming calls appears in the display.  
OK  
2. Use the Up and Down navigation keys to highlight a call, then press  
to view further information about the call.  
3. Press the Options (right) soft key (  
) to display a pop-up menu  
containing the following options:  
Save — Save the number to your Contacts.  
Details — Contacts calls only — Lets you view the Contacts entry for the  
originator of this call.  
Call Functions  
30  
       
Erase — Erase the selected call from your Incoming call list.  
Lock/Unlock — Blocks/permits erasure of the selected call from your Incoming  
call list.  
Erase all — Erase all unlocked calls from your Incoming call list.  
View Timers — Call Timer screen appears in the display listing the number  
and types of calls and their total durations. (See See “Call Timer” on page 33 for  
more information.)  
4. Use the Up and Down navigation keys to highlight an option.  
OK  
5. Press  
to perform the highlighted option’s function.  
Missed Calls  
The last 90 missed calls (calls not picked up) are stored in the Missed call log.  
Review the Missed call log for the time and date of the call, as well as other  
information.  
1. In standby mode, press the MENU (left) soft key (  
), then press  
(for Calls) and  
for Missed Calls. A list of your missed calls  
appears in the display.  
OK  
2. Use the Up and Down navigation keys to highlight a call, then press  
to  
view further information about the call.  
3. Press the Options (right) soft key (  
) to display a pop-up menu that  
contains the following options:  
Save — Save the number to your Contacts.  
Details — Contacts calls only — Lets you view the Contacts entry for the  
originator of this call.  
Erase — Erase the selected call from your Missed call list.  
Lock/Unlock — Blocks/permits erasure of the selected call from your Missed  
call list.  
Erase all — Erase all unlocked calls from your Missed call list.  
View Timers — Call Timer screen appears in the display listing the number  
and types of calls and their total durations. (See See “Call Timer” on page 33 for  
more information.)  
4. Use the Up and Down navigation keys to highlight an option.  
OK  
5. Press  
to perform the highlighted option’s function.  
Erase Logs  
You can erase Outgoing, Incoming, Missed, or All Calls.  
Erase All Calls  
1. In standby mode, press the MENU (left) soft key (  
), then press  
31  
       
Calls  
(for Calls) and  
for All Calls. The All Calls list appears in  
the display with the first call in the list highlighted.  
2. Press the Options (right) soft key (  
) to display a pop-up menu that  
contains the following options:  
Save — Save the number to your Contacts.  
Details — Contacts calls only — Lets you view the Contacts entry for the  
originator of this call.  
Erase — Erase the selected call from your All Calls list.  
Lock/Unlock — Blocks/permits erasure of the selected call from your All Calls  
list.  
Erase all — Erase all unlocked calls from your All Calls list.  
View Timers — Call Timer screen appears in the display listing the number  
and types of calls and their total durations. (See See “Call Timer” on page 33 for  
more information.)  
3. Use the Up and Down navigation keys to highlight Erase all, then press the  
OK  
key.  
4. Erase all entries?” appears in the display as well as the options Yes and  
No.  
5. To Erase all calls, press the Yes (left) soft key (  
).  
).  
To keep the calls, press the No (right) soft key (  
Data Call  
The last 90 data calls are stored in the Data call log. Review the Data call log for the  
time and date of the data call, as well as other information.  
1. In standby mode, press the MENU (left) soft key (  
), then press  
(for Calls) and for Data Call. The Data list appears in the display  
with the first call in the list highlighted.  
2. Press the Options (right) soft key (  
) to display a pop-up menu that  
contains the following options:  
Save — Save the number to your Contacts.  
Erase — Erase the selected data call from your Data list.  
Lock/Unlock — Blocks/permits erasure of the selected data call from your  
Data list.  
Erase all — Erase all unlocked data calls from your Data list.  
Data Counter — Data Counter screen appears in the display listing the amount  
of data Transmitted, Received, and the Total data transmitted and received since  
you last reset the Data Counter. Also listed is the Lifetime Data Counter that  
Call Functions  
32  
shows the total amount of data transmitted and received since your phone was  
3. Use the Up and Down navigation keys to highlight an option.  
OK  
4. Press  
to perform the highlighted option’s function.  
Call Timer  
View the duration of your last call, total calls, and calls made during the life of your  
phone using the Call timer feature. Call timer is not for billing purposes.  
1. In standby mode, press the MENU (left) soft key (  
), then press  
(for Calls) and  
for Call Timer. The following options appear in the  
display:  
Last Call — Shows the duration of your last call.  
All Calls — Shows the number and total duration of all calls originated by and  
made to your phone since the last erasure.  
Received Calls — Shows the number and total duration of all calls made to  
your phone since the last reset.  
Outgoing Calls — Shows the number and total duration of all calls originated  
by your phone since the last reset.  
Roaming Calls — Shows the number and total duration of all calls originated  
by and made to your phone while roaming and since the last reset.  
Lifetime Calls — Shows the duration of all calls on your phone since activation  
(Lifetime timers cannot be reset).  
2. Use the Up and Down navigation keys to highlight a particular timer.  
3. Press the Reset (left) soft key (  
) to reset the highlighted timer.  
) to reset all of the timers except  
Press the Reset All (right) soft key (  
Lifetime Calls.  
OK  
4. Press  
to exit the Call Timer screen.  
Note: Although Total call timers can be erased, LifeTime call timers can never be erased.  
Data Counter  
Use Data Counter to view the amount of data that has been sent or received (or a  
total of both) using the data services that your phone supports. The Data Counter can  
be a helpful tool for monitoring data usage, especially if your service agreement has  
specified limits.  
33  
             
Calls  
1. In standby mode, press the MENU (left) soft key (  
), then press  
(for Calls) and  
for Data Counter. The following options  
appear in the display:  
Transmit KB — Shows the amount of data (in kilobytes) that your phone has  
transmitted since last being reset.  
Received KB — Shows the amount of data (in kilobytes) that your phone has  
received since last being reset.  
Total — Shows the amount of data (in kilobytes) that your phone has  
transmitted and received since last being reset.  
Lifetime Data Counter — Shows the amount of data (in kilobytes) that your  
phone has transmitted and received since being activated.  
2. To reset a timer other than Lifetime Data Counter, use the Up/Down  
navigation keys to highlight the timer you want to reset and press the  
Reset (left) soft key (  
).  
3. To reset all timers except Lifetime Data Counter, press the Reset All (right)  
soft key (  
).  
OK  
4. Press  
to exit the Data Counter screen.  
Note: Although other data counters can be reset, only the Lifetime Data Counter can never be reset.  
Store Numbers from Call Logs  
Store numbers from your Outgoing, Incoming, Missed, and All calls logs to  
Contacts.  
Tip: In standby mode, briefly press  
to display the Recent Calls list. You can then select any call in the  
list to save to Contacts.  
1. In standby mode, press the MENU (left) soft key (  
), then press  
for Calls.  
2. Press the corresponding number on the keypad to view call logs for the  
following call types.  
for Outgoing Calls  
for Incoming Calls  
for Missed Calls  
for All Calls  
3. Use the Up and Down navigation keys to highlight the number you wish to  
store in Contacts and press  
OK  
.
Call Functions  
34  
 
4. Press the Options (right) soft key (  
), then use the Up and Down  
navigation keys to highlight Save.  
5. Select Create New to add the number as a Contacts entry, or select  
Update Existing to find a Contact with which to associate the new  
number.  
6. Follow the prompts to store the number to Contacts.  
35  
Menu Navigation  
Section 4: Menu Navigation  
Topics Covered  
This section explains the menu navigation for your phone. It also includes an  
outline of all the available menus associated with your phone.  
Note: Although all procedures in this section are written for the phone keypad, you can also perform these  
procedures using the QWERTY keypad.  
Menu Navigation  
Access the menus and sub-menus in your phone using the navigation key  
OK  
(
) and soft keys (  
or  
), or use a shortcut.  
1. In standby mode press the MENU (left) soft key (  
). The first of several  
menus appear in the display.  
Note: More than one menu may appear in your display. This setting can be modified in the Display / Menu  
Style menu. (See “Settings” on page 122 for more information.)  
2. Use the navigation key to browse through the menus.  
OK  
3. Press  
to enter the menu or sub-menu that appears in the display.  
4. Press the Back (right) soft key (  
) or the CLR key (  
) to return to  
the previous menu.  
Return to the Previous Menu  
Press the Back (right) soft key (  
When Back does not appear in the display, press  
menu.  
) to return to a previous menu.  
to return to the previous  
Menu Navigation  
36  
         
Menu Shortcuts  
Use shortcuts to quickly access menus and sub-menus. Press the MENU (left) soft  
key (  
), then press the number to the left of the menu to jump to the desired  
menu, sub-menu, or feature. For example, to jump to the Outbox sub-menu, press  
the MENU (left) soft key (  
), then press  
(for Messages) and  
for  
Outbox.  
Navigation Key Shortcuts  
QWERTY Keypad Closed  
In standby mode and with the QWERTY keypad closed, press a navigation key to  
launch the key’s corresponding application in the pattern shown here.  
Contacts  
Metro Web  
@Metro  
OK  
Messages  
QWERTY Keypad Open  
In standby mode and with the QWERTY keypad open, the navigation key application  
pattern rotates 90° as shown here.  
Contacts  
Metro Web  
@Metro  
Messages  
37  
     
Navigate Using a Shortcut  
QWERTY Keypad Shortcuts  
In standby mode and with the QWERTY keypad open, you have the option of using  
the arrow keys on the keypad itself to launch applications, as shown here.  
Contacts  
@Metro  
Metro Web  
Messages  
Navigate Using a Shortcut  
You can also access menus and sub-menus using menu numbers. Enter the menu  
number after pressing the MENU (left) soft key ( ) to go directly to the menu or  
sub-menu of your choice. Before you can navigate using a shortcut, you’ll need the  
menu or sub-menu number that you wish to access.  
1. In standby mode, press the MENU (left) soft key (  
).  
2. Press the number of the menu, sub-menu, and so on for the feature that  
you wish to access.  
Example: Press the MENU (left) soft key (  
), then press  
,
. This takes you to the  
Tools (MENU 8), and then to the Calendar (sub-menu 2).  
Menu Outline  
1
Contacts  
1.1  
1.2  
1.3  
1.4  
Find  
Add New Entry  
Speed Dial  
Group  
1.4.1 No Group  
1.4.2 Business  
1.4.3 Colleague  
1.4.4 Family  
1.4.5 Friends  
1.5  
Memory Info  
Menu Navigation  
38  
       
2
Calls  
2.1  
2.2  
2.3  
2.4  
2.5  
2.6  
2.7  
Outgoing Calls  
Incoming Calls  
Missed Calls  
All Calls  
Data Call  
Call Timer  
Data Counter  
3
Messages  
3.1  
Send Message  
3.1.1 Text Message  
3.1.2 Picture Message  
3.2  
3.3  
3.4  
3.5  
3.6  
Inbox  
Outbox  
Drafts  
Voicemail  
Erase Messages  
3.6.1 Inbox  
3.6.2 Outbox  
3.6.3 Drafts  
3.6.4 All Messages  
3.7  
Msg Settings  
3.7.1 General  
3.7.1.1  
3.7.1.2  
3.7.1.3  
3.7.1.4  
3.7.1.5  
3.7.1.6  
3.7.1.7  
3.7.1.8  
Auto Save  
Auto Erase  
Quick Text  
Voicemail #  
Entry Mode  
Callback #  
Signature  
Reminder  
3.7.2 Text Message  
3.7.2.1  
3.7.2.2  
Auto View  
Signature  
39  
Menu Outline  
3.7.2.3  
Auto Scroll  
3.7.3 Picture Message  
3.7.3.1  
3.7.3.2  
Auto Receive  
Signature  
4
5
6
@metro  
4.1  
@metro  
MetroWEB  
5.1  
Get In Web  
Voice SVC  
6.1  
Voice Commands  
6.2  
Voice Settings  
6.2.1 Choice Lists  
6.2.2 Sensitivity  
6.2.3 Digit Dialing  
6.2.3.1  
Adapt Digits  
Reset Digits  
6.2.3.2  
6.2.4 Sound  
6.2.4.1  
Prompts  
Digits  
6.2.4.2  
6.2.4.3  
Names  
6.2.4.4  
Name Settings  
6.2.4.4.1  
6.2.4.4.2  
Speed  
Volume  
6.2.5 Voice Launch  
6.2.6 About  
7
Multimedia  
7.1  
7.2  
7.3  
7.4  
Camera  
My Images  
My Ringtones  
My Sounds  
7.4.1 Record New  
Menu Navigation  
40  
8
Tools  
8.1  
Bluetooth  
8.1.1 Add New Device  
8.1.2 Registered List  
8.1.3 Bluetooth Settings  
8.1.3.1  
8.1.3.2  
8.1.3.3  
8.1.3.4  
Enable/Disable  
Discovery Mode  
Device Name  
Device Info  
8.2  
8.3  
8.4  
Calendar  
Memo Pad  
Alarm Clock  
8.4.1 Alarm 1  
8.4.2 Alarm 2  
8.4.3 Alarm 3  
8.5  
8.6  
8.7  
8.8  
World Time  
Calculator  
Stop Watch  
Converter  
8.8.1 Currency  
8.8.2 Length  
8.8.3 Weight  
8.8.4 Volume  
8.8.5 Area  
8.8.6 Temperature  
8.9  
Tip Calculator  
9
Settings  
9.1  
Location  
9.2  
Display Settings  
9.2.1 Wallpapers  
9.2.1.1  
My Images  
9.2.1.2  
Preset Images  
9.2.2 Clock Format  
9.2.3 Theme  
41  
Menu Outline  
9.2.4 Dialing Font  
9.2.4.1  
Style  
Size  
9.2.4.2  
9.2.5 Banner  
9.2.5.1  
Personal  
9.2.5.2  
ERI Banner  
9.2.6 Backlight  
9.2.6.1  
Main Display  
Keypad  
9.2.6.2  
9.2.6.3  
Brightness  
9.3  
Sound Settings  
9.3.1 Volume  
9.3.1.1  
Voice Calls  
Messages  
Alarms  
9.3.1.2  
9.3.1.3  
9.3.1.4  
Key Tone  
9.3.2 Ringer Type  
9.3.2.1  
Voice Calls  
9.3.2.1.1  
9.3.2.1.2  
Messages  
9.3.2.2.1  
9.3.2.2.2  
9.3.2.2.3  
My Ringtones  
My Sounds  
9.3.2.2  
9.3.2.3  
Text Message  
Picture Message  
Voicemail  
Roam Ringer  
9.3.2.3.1  
9.3.2.3.2  
My Ringtones  
My Sounds  
9.3.3 Alerts  
9.3.3.1  
Minute Beep  
Roaming  
9.3.3.2  
9.3.3.3  
Call Connect  
9.3.3.4  
Power On/Off  
9.4  
Call Settings  
9.4.1 Call Answer  
9.4.2 Auto Answer  
9.4.3 Auto Retry  
9.4.4 TTY Mode  
9.4.5 Voice Privacy  
Menu Navigation  
42  
9.4.6 Data Settings  
9.4.7 DTMF Tones  
9.5  
Phone Settings  
9.5.1 Airplane Mode  
9.5.2 Language  
9.5.3 Secruity  
9.5.3.1  
9.5.3.2  
9.5.3.3  
Lock Phone  
Change Lock  
Emergency #  
9.5.3.3.1  
9.5.3.3.2  
9.5.3.3.3  
911  
Empty  
Empty  
9.5.3.4  
9.5.3.5  
9.5.3.6  
Reset Phone  
Erase All Entry  
Restriction  
9.5.3.6.1  
9.5.3.6.2  
Outgoing  
Incoming  
9.5.4 NAM Selection  
9.5.5 System Select  
9.5.6 Clock Set  
9.5.6.1  
9.5.6.2  
Set Time  
Set Date  
9.5.7 Quick Search  
9.5.8 Auto Key Lock  
9.6  
9.7  
Memory Info  
9.6.1 Memory Usage  
9.6.2 My Images  
9.6.3 My Ringtones  
9.6.4 My Sounds  
Phone Info  
9.7.1 Phone Number  
9.7.2 Icon Glossary  
9.7.3 Version  
43  
Section 5: Entering Text  
Topics Covered  
This section outlines how to select the desired text entry mode when entering  
characters using the phone keypad or the nested, QWERTY keyboard-style keypad.  
This section also describes how to use the T9 predictive text entry system to  
reduce the number of key strokes needed to enter text.  
Entering Text  
44  
   
Built-in QWERTY Keypad  
Display  
CLR Key  
Fn (Input Mode) Key  
Left Soft Key  
Right Soft Key  
Navigation Keys  
Your r410 has a built-in, keyboard-style keypad, commonly called QWERTY, that you  
can access by sliding it open from beneath the top section of the phone. This also  
automatically rotates the image in the display to show information in a wider,  
landscape format. Using the QWERTY keypad, you can type letters, numbers,  
punctuation, and other special characters into text entry fields or other applications  
simpler and faster than using the telephone keypad.  
Note: Two of your phone’s functions (@metro and MetroWEB) call for you to use the QWERTY keypad. Other  
functions requiring text entry (such as, Messaging and Memo Pad) accept text entry from whichever  
keypad you prefer.  
Changing the Text Entry Mode  
Text messages can be made up of alphabetical characters, numbers, and symbols.  
You can use the following text entry modes to simplify text entry:  
T9 Word — Press each phone key only once to enter the letter of the word that  
you’re spelling. T9 WORD mode letter options are:  
T9 Word — Enter initial capital letters  
T9 WORD — Enter all upper case letters  
T9 word — Enter all lower case letters  
Note: T9 Word does not support the QWERTY keypad, which does not need this function.  
45  
       
Using T9® Mode (Phone Keypad Only)  
Abc — Enter letters, numbers, and symbols by using the QWERTY keypad or by  
repeatedly pressing each phone key until the desired character (as shown on the  
key) appears in the display. ABC mode letter options are:  
Abc — Enter initial capital letters  
ABC — Enter all upper case letters  
abc — Enter all lower case letters  
123 — Enter numbers by pressing the corresponding keys on the phone keypad or  
the QWERTY keypad.  
Tip: Using the QWERTY keypad, also use 123 mode to enter symbols into your message simply by pressing  
the keys labeled with the symbols you want.  
Symbols — Using the phone keypad, enter a symbol into your message by  
pressing the number above the symbol in the Symbols pop-up window.  
The current text entry mode (T9 Word, Abc, ABC, 123, or Symbols) is indicated in  
the lower part of a text entry screen. To change the text entry mode, do the  
following:  
1. While composing a text message, press the Left soft key (  
or  
).  
The following options appear in the display:  
T9Word  
Abc  
ABC  
123  
Symbols  
2. Use the Up and Down navigation keys to highlight the desired text entry  
OK  
mode, then press  
or  
.
Using T9® Mode (Phone Keypad Only)  
T9 Word recognizes commonly used words for the numeric sequence of key presses  
and inserts the word into your message. T9 Word is much faster than the traditional  
method of text entry (Abc) and requires only one key press per letter of the word that  
you’re spelling.  
1. While composing a text message, press the Left soft key (  
). Use the  
OK  
Up and Down navigation keys to highlight T9Word, then press  
or  
.
Entering Text  
46  
   
For practice, enter the word “Samsung” by pressing each of the following keys  
only once:  
S
A
M
S
U
N
G
T9 Word recognizes that the most commonly used word for the numeric  
sequence you just entered is “Samsung.” If more than one word shares the  
same numeric sequence, T9 Word provides the most commonly used word.  
Press  
to display other words, if available.  
Note: To enter a space, press the  
key. To enter a period, press the  
key. These key  
functions apply to both T9 Word and Abc modes. For other symbols, see "Entering Symbols" on  
Using Abc Mode  
1. While composing a text message, press the Left soft key (  
or  
).  
or  
Use the Up/Down navigation keys to highlight Abc, then press  
OK  
.
2. Enter characters while in Abc mode by using one of following keypads:  
Using the QWERTY keypad, press the key labeled with the desired character  
(such as, press for “G” and for “H”).  
Using the phone keypad:  
Press the key repeatedly until the desired character appears in the display (such  
as, press once for “G” and twice for “H”).  
Pause briefly and the displayed character is accepted and inserted into your  
message.  
Press  
Entering Numbers  
Enter numbers into a text message while in 123 mode.  
to enter a space and press  
to enter a period.  
1. While composing a text message, press the Left soft key (  
or  
).  
Use the Up/Down navigation keys to highlight 123, then press  
or  
OK  
.
2. Enter numbers while in 123 mode by using one of following keypads:  
Using the QWERTY keypad, press the key labeled with the corresponding  
number that you wish to insert into your message.  
47  
       
Entering Symbols  
Using the phone keypad, press the key labeled with the corresponding number  
that you wish to insert into your message.  
Entering Symbols  
Enter symbols such as “@” or “%” into a text message.  
While composing a text message, enter symbols by using one of following  
keypads:  
Using the QWERTY keypad:  
Press the Left soft key, use the Navigation key to highlight 123 (not Symbol),  
then press  
.
Press the key(s) labeled with the corresponding symbol(s) that you wish to insert  
into your message.  
To return to Abc mode, press the Left soft key, use the Navigation key to  
highlight Abc, then press  
Using the phone keypad:  
Press the Left soft key (  
.
), use the Navigation key to highlight Symbol, then  
press  
. The first of three symbol screens appear in the display.  
OK  
Use the Left and Right soft keys to page through the other symbols, if desired.  
Press the key that corresponds with the symbol that you wish to enter. For  
example, press  
for an exclamation point (!).  
Repeat these steps to insert additional symbols into your message.  
Entering Text  
48  
   
Section 6: Understanding Your Contacts  
Topics Covered  
This section details how you can manage your daily contacts by storing their  
names and numbers in your Contacts list. You can have your Contacts entries  
sorted by name.  
Note: Although the procedures in this section are written for the phone keypad, you can also perform these  
procedures using the QWERTY keypad.  
Contacts  
Up to 500 entries can be stored in Contacts. Each entry can have up to five  
associated phone numbers and one e-mail address. Each phone number can be up  
to 32 digits in length, including 2-Sec or Wait pauses (see “Manual Pause Calling”  
on page 23 for more information), and associated names can be up to 32 characters  
in length. You can assign the Speed Dial numbers of your choice for each entry. You  
can also mark your Contacts list as Restricted to prevent unauthorized viewing. (See  
Tip: Speed Dial One-Touch Dialing, Two-Touch Dialing, and Three-Touch Dialing allow you to call  
numbers stored in Contacts faster.  
49  
       
Finding a Contacts Entry  
Open Contacts  
1. In standby mode, press the MENU (left) soft key (  
), then press  
for Contacts. The following options appear in the display:  
Find — Find a phone number By Name.  
Tip: You can also access the Find option from standby mode, by pressing the Contacts shortcut (Up  
Navigation) key.  
Add New Entry — Add a number or e-mail address to your Contacts.  
Speed Dial — Assign a Contacts entry to a Speed Dial number. (See “Speed  
Dial” on page 59 for more information.)  
Group — Review, send messages to, add Contacts to, or rename four out of  
your five groups. (See “Contacts Groups” on page 61 for more information.)  
Memory Info — Display used and available memory for Contacts entries.  
Tip: To launch the Contacts menu using a voice command — In standby mode, press and hold  
until the phone prompts, “Say a command.” Say “Go to Contacts” into the microphone.  
2. Use the Up/Down navigation keys to highlight the option of your choice,  
OK  
and press the  
key.  
Tip: You can also press the keypad number key that corresponds to the menu option number.  
Finding a Contacts Entry  
Voice Method  
Use the VoiceSignal Lookup command to view contact information for any named  
contact stored in your Contacts list by saying the name.  
Note: The Lookup command shows the requested contact information in the display but does not dial any  
phone numbers for the contact.  
To look up information for a specific contact:  
1. In standby mode, press and hold the  
key to launch VoiceSignal.  
Say a Command” appears in the display and is pronounced through the  
speaker.  
2. Say “Lookup”.  
VoiceSignal prompts you to “Say the name.”  
3. Speak clearly and say the full name of the person you want to call, exactly  
as it is entered in your Contacts list.  
Understanding Your Contacts  
50  
       
If VoiceSignal recognizes the name you said, the contact information for that  
name appears in the display.  
If VoiceSignal does not recognize the name you said, a choice list of up to three  
names appears in the display, and VoiceSignal prompts you with “Did you  
say?” followed by the first name on the list.  
4. Say “Yes” to confirm the name or “No” to hear the next name, or use the  
keypad to select the correct name from the list. (See See “Choice Lists” on  
To say the name again, press the Repeat (right) soft (  
To exit VoiceSignal without dialing, press the Settings (left) soft (  
press the Exit (right) soft ( ).  
5. The contact information for the name you selected appears in the display.  
) key.  
) key and  
Press  
to dial the number associated with the name.  
Press the Erase (left) soft key (  
Press the EDIT key (  
Press the Options (right) soft key (  
display:  
) to erase this entry from your Contacts list.  
OK  
) to add or change information for this entry.  
) and the following options popup in the  
New Contact  
Erase  
Send Txt Msg  
Send Pic Msg  
Call  
Send Name Card With Bluetooth  
Shortcut Key Method  
If you’ve stored a name entry in Contacts, Find allows you to find it quickly.  
1. In standby mode, press the Contacts shortcut (Up Navigation) key.  
The Find screen appears in the display with the Go To field highlighted,  
followed by the first few names in your Contacts list.  
Tip: You can also access the Find screen from standby mode by pressing the MENU (left) soft key (  
),  
then pressing  
(for Contacts) and  
for Find.  
2. Enter a name as entered in Contacts. For example, if you saved the name  
as “Amy Smith”, begin the search by pressing (for “A”).  
As you enter letters, the names of the closest matches appear in the  
display.  
3. When the desired entry is listed in the display, use the Up/Down navigation  
keys to highlight the entry.  
51  
Adding a New Contacts Entry  
Press  
to dial the number associated with the name.  
Press the Edit (left) soft key (  
Press the VIEW key ( OK ) to show information about the entry.  
Press the Options (right) soft key (  
display:  
) to add or change information for this entry.  
). The following options appear in the  
New Contact — Add a new entry to Contacts.  
Erase — Erase the name and associated information.  
Send Txt Msg — Create and send a text message to the selected Contact.  
Send Pic Msg — Create and send a picture message to the selected Contact.  
Call — Dial the number associated with the name.  
Send Name Card With Bluetooth — Send a copy of a Contacts entry to  
another Bluetooth device.  
Use the Up/Down navigation keys to highlight an option, then press the OK  
key. The highlighted option’s sub-menu appears in the display.  
Adding a New Contacts Entry  
You can use either of two methods to add an entirely new entry to Contacts.  
Dial Method  
1. Using the keypad, enter the number you wish to add to your Contacts.  
2. Press the Save (left) soft key (  
). The following options appear in the  
display:  
Create New — Lets you create a new Contacts entry.  
Update Existing — Lets you add the number you entered to an existing  
Contacts entry.  
3. Use the Up/Down navigation keys to select Create New and press the  
OK key. The Select Type screen appears in the display showing the  
following icons:  
Mobile 1  
Mobile 2  
Home  
Work  
Fax  
Understanding Your Contacts  
52  
         
4. Use the Up/Down navigation keys to highlight the type that matches your  
new entry, then press the OK key.  
5. Use the keypad to enter a name to associate with the Contacts entry.  
6. Press the OK key to save the entry.  
Menu Method  
1. In standby mode, press the MENU (left) soft key (  
(for Contacts) and for Add New Entry.  
), then press  
The Add New Entry screen appears in the display with the Name field  
highlighted.  
2. Enter the name of the new entry using the keypad. (See “Entering Text” on  
page 44 for more information.)  
3. Use the Up and Down navigation keys to highlight one of the following  
fields:  
Mobile 1  
Home  
Work  
E-Mail 1  
Group  
Ringtone  
Mobile 2  
Fax  
E-Mail 2  
4. Enter a phone number in the highlighted field.  
5. Repeat steps 3 and 4 as needed.  
6. Press the OK key to save the new entry.  
Editing a Contacts Entry  
Editing Contacts Name and Numbers  
1. Find the Contacts entry you wish to change. See “Finding a Contacts  
2. Use the Up/Down navigation keys to highlight the entry and press the  
OK key. The View Contact screen appears in the display showing the  
highlighted entry’s information.  
3. Use the Up/Down navigation keys to review the information for the entry  
that you wish to change, then press the EDIT key ( OK ). The Edit  
Contact screen appears in the display.  
53  
       
Editing a Contacts Entry  
4. Use the Up/Down navigation keys to highlight the particular information  
you want to add or change.  
Press  
Press and hold  
Press the Options (right) soft key (  
display:  
to backspace and delete numbers or letters.  
to clear all numbers or letters in the highlighted field.  
). The following options popup in the  
Set Speed Dial / Remove speed dial — Assign/remove a speed dial number  
(see "Speed Dial" on page 59. for more information).  
Set as default — Set the number the phone will dial when Contacts dialing,  
speed dialing, or voice dialing.  
2-Sec Pause — A 2-second pause after which dialing resumes (see "Add  
Wait — A hard pause (waits for input from you).  
Use the Up/Down navigation keys to highlight the desired option, then press the  
OK key.  
5. When you’re finished changing the contents of a field, press the OK key.  
Your changes are saved and a confirmation message appears in the  
display.  
Add Pauses to Contacts Numbers  
Calls to automated systems such as banking services often require a password or  
account number. Instead of manually entering these numbers, you can store them in  
a Contacts entry with the phone number and with special characters called pauses,  
up to a maximum of 32 digits.  
Wait — Stops the calling sequence until the phone receives further input.  
2-Sec Pause — Stops the calling sequence for two seconds, then sends the  
remaining digits.  
Note: You can enter multiple Waits to extend the length of a pause. For example, two consecutive Waits  
cause a total pause time of four seconds. Keep in mind that pauses count as digits towards the 32-  
digit maximum.  
Understanding Your Contacts  
54  
         
To add pauses to a Contacts entry number, do the following:  
1. Find the Contacts entry associated with the number you want to include  
information.  
2. Select and edit the desired number. See “Editing a Contacts Entry” on  
page 53 for more information.  
3. Press the Options (right) soft key (  
). The following pause options  
appear in the display:  
Wait — A hard pause (waits for input from you).  
2-Sec Pause — A 2-second pause after which dialing resumes.  
4. Use the Up/Down navigation keys to highlight the pause option of your  
choice.  
5. Press the OK key to enter the highlighted pause into the number  
sequence.  
6. When you’re finished entering information, press the OK key to store  
the number to Contacts.  
Pause Dial from Contacts  
1. If you stored the number using 2-second pause(s), simply recall the  
number from Contacts.  
2. If you stored the number using Wait(s), recall the number from Contacts  
and wait for the appropriate prompt from the dialed number.  
3. Press  
to dial the number.  
Edit an Existing E-mail Address  
1. Find the Contacts entry you want to edit. See “Finding a Contacts Entry” on  
2. Use the Up/Down navigation keys to highlight the desired Contacts entry,  
then press the Edit (left) soft key (  
).  
The Edit Contact screen appears in the display.  
3. Use the Up/Down navigation keys to highlight the E-Mail field.  
4. Use the keypad to edit the e-mail address. (See “Entering Text” on page 44  
for more information.)  
5. Press the OK key to save your changes.  
55  
 
Editing a Contacts Entry  
Assigning a Picture to a Contacts Entry  
When you assign a picture to a Contacts entry, the picture that you assigned to the  
entry appears in the display when you receive a call from that Contact.  
1. Find the Contacts entry you want to edit. See “Finding a Contacts Entry” on  
page 50 for more information.  
2. Use the Up/Down navigation keys to highlight the desired Contact, then  
press the Edit (left) soft key (  
).  
The Edit Contact screen appears in the display.  
3. Use the Up/Down navigation keys to highlight the Picture ID field (at the  
top of the Edit Contact screen), then press the Set (left) soft key (  
).  
A photo gallery screen appears in the display, showing a series of  
information.)  
4. Use the Up/Down navigation keys to highlight the picture that you wish to  
assign to the Contacts entry.  
If there are no pictures, press the Camera (left) soft key (  
cannot find an appropriate picture, press the Camera (right) soft key  
).  
). If you  
(
The camera viewfinder screen appears in the display.  
5. Press the TAKE key ( OK ). The picture you have taken appears in the  
display.  
6. Press the Save (left) soft key (  
). You are returned to the camera  
). You are returned to the photo  
viewfinder screen.  
7. Press the My Images (left) soft key (  
gallery screen.  
8. Use the Up/Down navigation keys to highlight the picture that you wish to  
assign to the Contacts entry, the press the OK key. The Contacts entry  
screen appears in the display with a thumbnail view of the selected image  
in the Picture ID field.  
9. Press the OK key to save the picture assignment to the selected  
Contacts entry.  
Understanding Your Contacts  
56  
 
Assigning a Ringtone to a Contacts Entry  
When you assign a ringtone to a Contacts entry, the phone plays the ringtone that  
you assigned to the entry when you receive a call from that Contact instead of the  
ringtone currently assigned to Voice Calls.  
1. Find the Contacts entry you want to edit. See “Finding a Contacts Entry” on  
2. Use the Up/Down navigation keys to highlight the desired Contact, then  
press the Edit (left) soft key (  
). The Edit Contact screen appears in  
the display.  
3. Use the Up/Down navigation keys to highlight the Ringtone field, then  
press the Set (left) soft key ( ). The Contact Tone menu showing the  
following options appears in the display:  
My Ringtones  
My Sounds  
4. Use the Up and Down Up/Down navigation keys to highlight the desired  
option, then press the OK key.  
The My Ringtones or the My Sounds file list appears in the display.  
5. Use the Up/Down navigation keys to highlight the ringtone or sound that  
you wish to assign to the Contacts entry.  
6. Press the OK key. The Contacts entry screen appears in the display with  
the name of the selected file in the Ringtone field.  
7. Press the OK key to save the ringer assignment to the selected Contacts  
entry.  
Saving a Number After a Call  
Once you finish a call, you can store the caller’s number to your Contacts list.  
Note: If the call was incoming and Caller ID information was unavailable, then the Save option is also  
unavailable.  
1. Press  
to end your call. The call time, length of call, phone number,  
and name of the party (if available) appear in the display.  
2. Press the Save (right) soft key (  
). The following options appear in the  
display:  
Create New — Lets you create a new Contacts entry.  
Update Existing — Lets you add the number you entered to an existing  
Contacts entry.  
57  
     
Saving a Number After a Call  
3. Follow the instructions in the upcoming sections depending on whether the  
number is a new entry or you wish to add it to an existing entry.  
Create a New Entry  
1. Use the Up/Down navigation keys to highlight Create New and press the  
OK key. The Create New screen appears in the display showing the  
following number type options:  
Mobile 1  
Mobile 2  
Home  
Work  
Fax  
2. Use the Up/Down Up/Down navigation keys to highlight the number type  
that matches your new entry, then press the OK key.  
3. Enter a name for the new entry (see “Entering Text” on page 44 for more  
information).  
4. Press the OK key. The new entry is saved to your Contacts list.  
Add to an Existing Entry  
1. Use the Up/Down navigation keys to highlight Update Existing and press  
the OK key. The Update Existing screen appears in the display showing  
your Contacts list with the Go To field and the first Contacts entry  
highlighted.  
2. Find the Contacts entry to which you want to add the new number. See  
3. Press the OK key. The following number type options appear in the  
display:  
Mobile 1  
Mobile 2  
Understanding Your Contacts  
58  
   
Home  
Work  
Fax  
Number types that are already assigned a number show the number  
instead of the number type label.  
4. Use the Up/Down navigation keys to highlight the desired unassigned  
number type, then press the OK key. The Contacts entry information  
appears in the display with the new number posted in the appropriate  
number type field.  
5. Press the OK key again to save your changes to the existing entry.  
Speed Dial  
A Contacts entry’s Speed Dial number corresponds to the number keys you press to  
speed dial one of that entry’s numbers. For example:  
To speed dial the Contacts entry assigned to Location 5, press and hold the  
key, (1-touch dialing).  
To speed dial the Contacts entry assigned to Location 35, press  
and hold the key, (2-touch dialing).  
To speed dial the Contacts entry assigned to Location 235, press  
, then press and hold the key (3-touch dialing).  
then press  
, press  
You can assign one or more Speed Dial numbers to a Contacts entry during new  
entry creation or by editing an existing entry.  
Assignment During Entry Creation  
To assign a Speed Call number to a new Contacts entry number, do the following:  
1. Follow either of the New Contacts entry procedures (see “Adding a New  
Contacts Entry” on page 52) until you enter a name for the entry.  
2. After entering the Contacts entry name, do not press the OK key.  
Instead, use the Up/Down Up/Down navigation keys to highlight the  
number field.  
3. Press the Options (right) soft key (  
). The following options appear in  
the display:  
Set Speed Dial — Assign a speed dial number.  
59  
       
Speed Dial  
Set as default — Set the number the phone will dial when Contacts dialing,  
speed dialing, or voice dialing.  
Wait — A hard pause (waits for input from you).  
2-Sec Pause — A 2-second pause after which dialing resumes (see "Add  
Use the Up/Down Up/Down navigation keys to highlight Set Speed Dial,  
then press the OK key. The Speed Dial screen appears in the display.  
4. Use the Up/Down Up/Down navigation keys to highlight an Unassigned  
Speed Dial number or enter an Unassigned Speed Dial number in the Go  
To field using the keypad.  
Important!: Do not enter Speed Call numbers 1 or 911. These numbers are already assigned to Voicemail  
(001) and to emergency use (911).  
5. Press the SET key ( OK ). You are prompted to confirm your Speed Dial  
number assignment.  
6. Press the Yes (left) soft key (  
) to save your Speed Dial assignment and  
return to the Add New Entry screen.  
Note: Press the No (right) soft key (  
) to discard the assignment and return to the Speed Dial screen.  
7. Press the OK key to save your changes.  
Changing a Speed Dial Location  
1. Find the Contacts entry you want to edit. See “Finding a Contacts Entry” on  
page 50 for more information.  
2. Use the Up and Down navigation keys to highlight the desired entry.  
3. Press the Edit (left) soft key (  
4. Use the Up and Down navigation keys to highlight the number field marked  
by the Speed Dial icon ( ).  
).  
5. Press the Options (right) soft key (  
). The following options appear in  
the display:  
Remove speed dial — Unassign the current speed dial number.  
Set as default — Set the number the phone will dial when Contacts dialing,  
speed dialing, or voice dialing.  
Wait — A hard pause (waits for input from you).  
2-Sec Pause — A 2-second pause after which dialing resumes (see “Add  
Understanding Your Contacts  
60  
Use the Up/Down navigation keys to highlight Remove speed dial, then  
press the OK key. “Remove speed dial?” pops up in the display to  
confirm your desire to remove the entry.  
6. Press the Yes (left) soft key (  
) to remove the Speed Dial assignment.  
Speed Dial Removed” pops up in the display, and you are returned to the  
Edit Contact screen.  
Contacts Groups  
Contact Groups let you easily send messages to multiple, selected Contacts. You can  
also use Groups to find Contact entries and to add/remove Contacts names in a  
Group or to create or rename a Group.  
Add Contacts Entry to a Group  
Using Add New/Edit Contact Option  
To add a Contact to a Group using either the Add New Contact option or the Edit  
Contact option, do the following:  
1. Create a Contacts entry (see “Adding a New Contacts Entry” on page 52  
for more information) or find a Contacts entry (see “Finding a Contacts  
Entry” on page 50 for more information) that you want to add to a Group.  
2. Use the Up and Down navigation keys to highlight the Group field, the  
press the Set (left) soft key (  
).  
The Select Group screen appears in the display showing Groups similar to  
the following:  
No Group  
Business  
Colleague  
Family  
Friends  
3. Use the Up and Down navigation keys to highlight the Group to which you  
want to assign the selected Contact, then press the OK key.  
You are returned to the Add New Entry/Edit Contact screen and the  
selected Group name populates the Group field.  
4. Press the OK key to save your changes.  
61  
 
Contacts Groups  
Using Group Add Option  
The Add option lets you add one or more existing Contacts to a Group.  
1. In standby mode, press the MENU (left) soft key (  
(for Contacts) and for Group.  
), then press  
The Group List screen appears in the display showing Groups similar to  
the following:  
No Group  
Business  
Colleague  
Family  
Friends  
2. Use the Up and Down navigation keys to highlight a Group, then press the  
Options (right) soft key ( ). The following options popup in the display:  
Send Txt Msg  
Send Pic Msg  
Rename  
Erase  
Add  
3. Use the Up and Down navigation keys to highlight Add, then press the  
OK key.  
The Add Contacts screen appears in the display showing a list of Contacts  
entries.  
4. Do one of the following:  
Use the Up/Down navigation keys to highlight an entry you want to add to the  
group, then press the MARK key ( OK ). A checkmark appears in the entry’s  
checkbox.  
Repeat as needed to check all the desired Contacts.  
Press the Mark All (right) soft key (  
).  
Note: To unmark a marked Contact, highlight the Contact and press the MARK key ( OK ) to clear the  
checkmark.  
5. When you have marked the Contacts you want to add to the group, press  
the Done (left) soft key (  
display, followed by the selected Group list including the added Contacts.  
Rename a Group  
). “Contact added to group” appears in the  
The Rename option lets you change the name any of the Groups, except No Group.  
Understanding Your Contacts 62  
1. In standby mode, press the MENU (left) soft key (  
), then press  
(for Contacts) and  
for Group. The Group List screen appears in  
the display.  
2. Use the Up/Down navigation keys to highlight the Group name other than  
No Group that you wish to change, then press the Options (right) soft key  
(
). The following options popup in the display:  
Send Txt Msg  
Send Pic Msg  
Rename  
Erase  
Add  
3. Use the Up and Down navigation keys to highlight Rename, then press the  
OK key.  
The Rename Group screen appears in the display.  
on page 44 for more information.)  
5. When you have completed your changes to the Group name, press the  
SAVE key ( OK ).  
Group Renamed” appears in the display followed by the Group List  
screen showing your renamed Group.  
Add a New Group  
The New option lets you add Groups.  
1. In standby mode, press the MENU (left) soft key (  
), then press  
(for Contacts) and  
appears in the display.  
for Group. The Group List screen  
2. Press the New (left) soft key (  
). The New Group screen appears in the  
display.  
3. Enter a new group name using the keypad. (See “Entering Text” on page  
44 for more information.)  
4. When you have completed entering the new Group name, press the SAVE  
key ( OK ). “Group Saved” appears in the display followed by the Group  
List screen showing your new Group.  
Erase a Group  
The Erase option lets you delete a Group, thus freeing you to reassign the Contacts  
formerly in the Group.  
63  
Deleting a Contacts Entry  
1. In standby mode, press the MENU (left) soft key (  
(for Contacts) and  
appears in the display.  
2. Use the Up and Down navigation keys to highlight the Group that you wish  
), then press  
for Group. The Group List screen  
to delete, then press the Options (right) soft key (  
).  
The following options popup in the display:  
Send Txt Msg  
Send Pic Msg  
Rename  
Erase  
Add  
3. Use the Up and Down navigation keys to highlight Erase, then press the  
OK key.  
You are prompted to confirm the Group erasure.  
4. Press the Yes (left) soft key (  
) to confirm erasure of the Group. Press  
the No (right) soft key (  
) to retain the Group.  
Deleting a Contacts Entry  
1. Find the Contacts entry you want to delete. (See “Finding a Contacts Entry”  
2. Use the Up/Down navigation keys to highlight the desired entry.  
3. Press the Options (right) soft key (  
). The following options appear in  
the display:  
New Contact  
Erase  
Send Txt Msg  
Send Pic Msg  
Call  
4. Use the Up/Down navigation keys to highlight Erase, then press the OK  
key. The phone prompts you to confirm the erasure.  
5. Press the Yes (left) soft key (  
) to confirm erasure of the selected  
) to retain the Contact.  
Contact. Press the No (right) soft key (  
Memory Info  
The Memory Info menu option lets you view the amount of memory you have used  
to store Contacts entries, as well as the memory remaining to store more Contacts  
entries.  
Understanding Your Contacts  
64  
       
In standby mode, press the MENU (left) soft key (  
), then press  
(for Contacts) and for Memory Info.  
The Memory Info Contacts screen appears in the display showing the  
amount of memory Used and remaining (Free) for Contacts entries.  
65  
Accessing @metro (Mobile Shop)  
Section 7: @metro  
Topics Covered  
With Mobile Shop, you can download full featured applications over the air  
including games, personalized ring tones, pictures, and more. You can send and  
receive instant messages and email, or browse the web to catch up on all the  
latest news.  
This section outlines how to obtain games and other applications for your phone.  
For more information, contact your Wireless Carrier.  
Accessing @metro (Mobile Shop)  
1. Open the QWERTY keypad.  
Note: @metro is only accessible using the QWERTY keypad.  
2. In standby mode, do one of the  
following to launch @metro:  
Press the Right navigation key.  
Press the MENU (left) soft key (  
),  
then press  
(for @metro) and  
for @metro.  
The @metro menu appears in the  
display as shown.  
Applications Shopping and  
Downloading  
Download games, ring tones, e-mail, and more using the Mobile Shop. For  
information on airtime charges, contact your Wireless Carrier.  
1. At the @metro menu, use the Left and Right navigation keys to highlight  
the Mobile Shop icon (  
), then press the OK key.  
@metro  
66  
       
Note: The first time you access the Mobile Shop, “Browsing online and downloading apps may incur  
network usage charges” appears in the display along with instructions on how to remove this  
message.  
Your phone takes a moment to connect, then the Mobile Shop Catalog  
menu appears in the display.  
2. Follow the instructions in your phone’s display.  
Note: Please check with your Wireless Carrier for availability of applications.  
Changing Your @metro Settings  
Use the Settings menu in Mobile Shop to manage, move, order applications, and  
much more.  
1. At the @metro menu, use the Left and Right navigation keys to highlight  
the Settings icon ( ), then press the OK key. The following options  
appear in the display:  
Order Apps — Download applications over the network.  
Move Apps — Move previously downloaded applications between available  
folders.  
Manage Apps — View used and available memory.  
Main Menu View — Select whether you wish to view the main Mobile Shop  
menu in a list or icon format.  
View Log — View the Mobile Shop log, which displays information about  
recent activity using Mobile Shop.  
2. Use the Up and Down navigation keys to highlight the desired option.  
3. Press the OK key to enter the option’s sub-menu and view or change  
settings.  
Using On-line Help  
The Help sub-menu within @metro is a short tutorial on several @metro-Mobile  
Shop features. View information about charges, cancelling subscriptions, buying  
apps, disabling apps, and more.  
1. At the @metro menu, use the Left and Right navigation keys to highlight  
the Help ( ) icon.  
?
OK  
2. Press the  
key. The Help subjects described in the following  
subsections appear in the display.  
3. Use the Up and Down navigation keys to highlight the desired Help subject.  
4. Press the OK key to view the selected Help information.  
67  
   
Accessing @metro (Mobile Shop)  
Buying New Apps  
To buy new and exciting apps, visit the MobileShop. It provides you with a variety of  
apps you can choose from.  
What do I pay?  
When you buy an app, you will be charged for the purchase cost of the app.  
Demo Apps  
A Demo app is free and is designed to demonstrate the app’s main features. It  
usually expires after a certain period of time or a number of uses and often has  
limited functions. When you run a demo app, you will be presented with a purchase  
option so you won’t have to look for the app in the MobileShop.  
Removing Apps  
You may remove apps that are no longer needed. When you remove an app, you  
cannot use the application unless you purchase it again. To remove an app, choose  
Settings > Manage Apps. Then, select the app you want to remove.  
Disabled Apps  
You can install new apps even if the memory of your phone is full by partially  
removing (disabling) apps you haven’t used recently. When you need to use a  
disabled app, you can restore it at no additional purchase cost.  
Restoring Apps  
Disabled apps can be quickly restored at no additional purchase cost. To restore an  
app, run the application you want to restore from the Main Menu. You will be guided  
through the restoration process.  
Expired Apps  
Apps that were purchased based on the number of uses or time expire. You can  
purchase additional uses from the MobileShop.  
@metro  
68  
           
Section 8: Messaging  
Topics Covered  
This section explains how to send or receive different types of messages. This  
section also describes the features and functionality associated with messaging.  
Note: Although the procedures in this section are written for the phone keypad, you can also perform these  
procedures using the QWERTY keypad.  
69  
   
Types of Messages  
Types of Messages  
Your phone is able to send and receive Text and Picture messages to compatible  
phones and devices. Text messages can be up to 160 characters in length.  
Note: Available memory is shared between all messages. You can store up to 100 messages. However, the  
exact number is dependent upon message length.  
Create and Send Text Messages  
1. In standby mode, press the Messages (Down navigation) key, then press  
(for Send Message) and  
for Text Message. The Create  
Txt Msg screen appears in the display showing the To: list.  
Tip: To launch the Create Txt Msg screen using a voice command — In standby mode, press and hold  
until the phone prompts, “Say a command.” Say “Send Text” into the microphone. You are  
then prompted to say a Contact name or a number for the first recipient of the message.  
2. Enter the phone number or e-mail address of the recipient, then press the  
OK  
key. The Text: appears in the display.  
3. Enter the text content of your message using the keypad. See “Entering  
Text” on page 44 for more information. At any point while composing a  
message:  
Press the Left soft key (  
entry options appear in the display:  
) to change the text entry mode. The following text  
T9 Word  
Abc  
ABC  
123  
Symbols  
Shortcuts  
Add T9 Word  
Use the Up and Down navigation keys to highlight the desired option, then press  
OK  
the  
key.  
Press the Options (right) soft key (  
) to complete the message text and set  
message send options. The following options appear in the display:  
Edit Send To — Edit the recipient’s number or email address.  
Quick Text — Insert pre-composed text in your message.  
Save As Draft — Save the message to your Draft folder.  
Priority Level — Choose High or Normal.  
Validity Period — Enter the Date when this message will cease to be valid,  
then use the Left and Right navigation keys to choose the Time.  
Messaging  
70  
           
Enh. Delivery Ack — Choose On or Off — Requests confirmation when your  
message is received.  
Add To Contacts — Save the recipient’s number or e-mail address as a  
Contacts list entry.  
4. Once you’re finished entering your message, press the OK key.  
Receive Text Messages  
When you receive a message in standby mode, the ringer sounds (unless turned off)  
and New Message appears in the display along with the closed envelope icon ( ).  
The date and time of the message also appear in the display along with the following  
options:  
View Now — Opens the message, where you have the option to Forward, Reply  
With Copy, Save Quick Text, Lock, Add To Contacts, Message Info, or Extract.  
View Later — Saves the message to your inbox, where you can view it later, then  
returns your phone to standby mode.  
Use the Up and Down navigation keys to highlight your choice, then press the OK  
key.  
Receive Messages While in a Call  
When you receive a message while in a call, New Message appears in the display  
along with the closed envelope icon ( ). The date and time of the message also  
appear in the display along with the following options:  
View Now — Opens the message, where you have the option to Forward, Reply  
With Copy, Save Quick Text, Lock, Add To Contacts, Message Info, or Extract.  
View Later — Saves the message to your inbox, where you can view it later, and  
returns your phone to call mode.  
Use the Up and Down navigation keys to highlight the desired option, then press the  
OK key.  
Send Picture Messages in Camera Mode  
Picture messages can be sent to recipients with compatible phones or devices. You  
can even accompany a Picture message with a voice memo or preloaded sound.  
Tip: You can send a Picture message to up to ten recipients. Enter each recipient’s address or phone  
number in a separate Send to field of the Picture message composer.  
1. In standby mode, press the Camera key (  
). The camera viewfinder  
screen appears in the display.  
71  
             
Send Picture Messages in Camera Mode  
2. Using the display as a viewfinder, when the image that you wish to send  
appears in the display, press the TAKE key ( OK ) to take a picture.  
Note: For more information about using the camera feature in your phone, see “Multimedia” on page 95.  
3. Press the SEND key ( OK ) to save the picture and begin delivery process.  
The Create Pic Msg screen then appears in the display with the Send To:  
list highlighted.  
4. Enter the phone number or e-mail address of the recipient of the Picture  
message, then press the OK key.  
Tip: Press the Add (right) soft key (  
) to display a pop-up menu containing: Contacts, Groups, and  
Recent Calls. These options allow you to find and add recipients to the Send To: list.  
5. The Subject: field appears in the display. Enter a subject for the Picture  
message using the keypad. (See See “Entering Text” on page 44 for more  
information.)  
6. Press the Down navigation key until the Text: field is highlighted, then  
enter the message text using the keypad. (See See “Entering Text” on page  
44 for more information.)  
7. Your new picture appears in the Pic: field.  
8. If you wish to insert a sound into your Picture message, use the Down  
navigation key to highlight the Sound: field and do the following;  
otherwise, proceed to step 10.  
Press the Sounds (left) soft key (  
display showing the following options:  
). The My Sounds screen appears in the  
Record New — Record a new memo to insert into the message.  
Note: You can record and insert a voice memo of up to 60 seconds in length, if you record first before  
attaching a picture. If a picture is attached before recording, the size of the voice memo is limited to  
the amount of remaining memory.  
Audio files list — Select from the list of previously recorded voice memos and  
preloaded audio files on your phone.  
Use the Up/Down navigation keys to highlight an option, then press the OK  
key to select the option and insert a sound into your message.  
Press OK to exit the pop-up menu without inserting a sound.  
Messaging  
72  
9. Press the Options (right) soft key (  
) to complete the message text and  
set message send options. The following options appear in the display:  
Preview — View the picture as the recipient will see it.  
Add Quick Text — Add precomposed text to your message.  
Save As Draft — Save the message to your Draft folder.  
Priority Level — Choose High or Normal.  
Validity Period — Enter the Date when this message will cease to be valid,  
then use the Left and Right navigation keys to choose the Time.  
Delivery Ack — Choose On or Off — Requests confirmation when your  
message is received.  
Remove Pic — Remove the picture from your message.  
Remove Sound — Remove the sound file from your message.  
Add To Contacts — Save the recipient’s number or e-mail address as a  
Contacts list entry.  
Use the Up/Down navigation keys to highlight an option, then press the  
OK key to invoke the option.  
10. Press the OK key to send the message. “Pic Msg Sending” appears in  
the display and a progress bar indicates the send status.  
Send Picture Messages in Standby Mode  
Send Picture messages to recipients with a compatible phone or other device, and  
accompany the Picture message with a voice memo, ring tone, or downloaded  
melody.  
Tip: You can send a Picture message to up to ten recipients. Enter each recipient’s address or phone  
number in a separate Send To field of the Picture message composer.  
1. In standby mode, press the Messages (Down navigation) key, then press  
(for Send Message) and  
for Picture Message. The  
Create Pic Msg screen then appears in the display with the Send To tab  
highlighted and showing the To: list.  
Tip: To launch the Create Pic Msg screen using a voice command — In standby mode, press and hold  
until the phone prompts, “Say a command.” Say “Send Picture” into the microphone. You  
are then prompted to say a Contact name or a number for the first recipient of the message.  
2. Enter the phone number or e-mail address of the recipient using the  
keypad, then press the OK key.  
Tip: Press the Add (right) soft key (  
) to display a pop-up menu containing: Contacts, Groups, and  
Recent Calls. These options allow you to find and add recipients to the Send To: list.  
73  
   
Send Picture Messages in Standby Mode  
3. The Subject: field appears in the display. Enter a subject for the Picture  
information.)  
4. Press the Down navigation key until the Text: field is highlighted, then  
enter the message text using the keypad. (See “Entering Text” on page 44  
for more information.)  
5. Press the Down navigation key until the Pic: field is highlighted, then press  
the Images (left) soft key (  
). A photo gallery of thumbnail images  
appears in the display.  
6. Use the navigation keys to highlight a picture to be added to your  
message, then do the following:  
If you want, press the View (left) soft key (  
picture to full-screen size.  
) to expand the highlighted  
If you want to include a new picture, press the Camera (right) soft key (  
).  
Note: For more information about using the camera feature in your phone, see “Multimedia” on page 95.  
Press the OK key to add the highlighted picture to your message.  
You are returned to the Create Pic Msg screen with the selected picture in  
the Pic: field.  
7. If you wish to insert a sound into your Picture message, use the Down  
navigation key to highlight the Sound: field and do the following;  
otherwise, proceed to step 8.  
Press the Sounds (left) soft key (  
display showing the following options:  
). The My Sounds screen appears in the  
Record New — Record a new memo to insert into the message.  
Note: You can record and insert a voice memo of up to 60 seconds in length, if you record first before  
attaching a picture. If a picture is attached before recording, the size of the voice memo is limited to  
the amount of remaining memory.  
Audio files list — Select from the list of previously recorded voice memos and  
preloaded audio files on your phone.  
Use the Up/Down navigation keys to highlight an option, then press the OK  
key to select the option and insert a sound into your message.  
Press OK to exit the pop-up menu without inserting a sound.  
8. Press the Options (right) soft key (  
set message send options. The following options appear in the display:  
Preview — View the picture as the recipient will see it.  
) to complete the message text and  
Messaging  
74  
Add Quick Text — Add precomposed text to your message.  
Save As Draft — Save the message to your Draft folder.  
Priority Level — Choose High or Normal.  
Validity Period — Enter the Date when this message will cease to be valid,  
then use the Left and Right navigation keys to choose the Time.  
Delivery Ack — Choose On or Off — Requests confirmation when your  
message is received.  
Remove Pic — Remove the picture from your message.  
Remove Sound — Remove the sound file from your message.  
Add To Contacts — Save the recipient’s number or e-mail address as a  
Contacts list entry.  
Use the Up/Down navigation keys to highlight an option, then press the  
OK key to invoke the option.  
9. Press the OK key to send the message. “Pic Msg Sending” appears in  
the display and a progress bar indicates the send status.  
Receive Picture Messages  
When you receive a Picture Message in standby mode, the ringer sounds (unless  
turned off) and New Message appears in the display along with the closed envelope  
icon ( ). The date and time of the message also appear in the display along with  
the following options:  
View Now — Retrieves and opens the message, where you have the option to  
Reply, Forward, Delete, Save Text, Save Pic, or Save Msg.  
View Later — Saves the message to your inbox, where you can view it later, then  
returns your phone to standby mode.  
Use the Up and Down navigation keys to highlight the desired option, then press the  
OK key.  
View a Picture Message Later  
1. In standby mode, Messages (Down navigation) key, then press  
(for Inbox). The Inbox appears in the display.  
2. If the new picture message is not highlighted, use the Up and Down  
navigation keys to highlight the new message.  
3. Press the OK key. “Connecting” appears in the display followed by  
Retrieving” and a progress bar indicating that the message is  
downloading to your phone.  
75  
       
Message Boxes  
4. Once a Picture message has been downloaded to your phone, the new  
Picture message appears in the display. If the message includes a sound  
file, the phone begins playing it.  
Note: For more information on viewing and managing received picture messages, see “Inbox” on page 76.  
View a Picture Message Now  
1. After you select the View Now option, “Connecting” appears in the  
display followed by “Retrieving” and a progress bar indicating that the  
message is downloading to your phone.  
2. After the Picture message has downloaded, an alert sounds, and the new  
Picture message appears in the display. If the message includes a sound  
file, the phone begins playing it.  
3. While viewing your message press the Options (right) soft key (  
). The  
following options appear in the display:  
Replay — Play the sound file included in the picture message again.  
Forward — Send a copy of this message to another recipient.  
Reply With Copy — Compose and send a reply message to the originator of  
the received message and include a copy of the original message.  
Save Sound — Save the sound file included in this message to the My Sounds  
folder.  
Save Pic — Save the picture included in this message to the My Images folder.  
Save Quick Text — Save the text in this message as a new Quick Text.  
Lock / Unlock — Block/permit erasure of the highlighted message.  
Add To Contacts — Save the sender’s number to your Contacts.  
Message Info — Shows message delivery status, addressee, size, and so on.  
4. Use the Up/Down navigation keys to highlight an option. Press the OK  
key to perform the function for the highlighted option.  
Note: For more information on received picture message options, see “Inbox” on page 76.  
Message Boxes  
Your phone stores messages in any one of five message boxes. The subsections that  
follow describe each message box in detail.  
Inbox  
Received messages of all types (except Voicemail) are stored in the Inbox.  
1. In standby mode, press the Messages (Down navigation) key, then press  
Messaging  
76  
       
for Inbox. A list of incoming messages appears in the display.  
Tip: While in a call, press the Options (right) soft key (  
), then press  
to open the Messages  
menu.  
2. Use the navigation keys to highlight the message that you wish to view.  
3. Press the OK key to view contents of the highlighted message.  
4. While viewing your message press the Options (right) soft key (  
). The  
following options appear in the display:  
Forward — Send a copy of this message to another recipient.  
Reply With Copy — Compose and send a reply message to the originator of  
the received message and include a copy of the original message.  
Save Sound — Picture Messages Only — Save the audio file (sound) included  
in this message to the My Sounds folder.  
Save Pic — Picture Messages Only — Save the picture included in this  
message to the My Images folder.  
Save Quick Text — Save the text in this message as a new Quick Text.  
Lock / Unlock — Block/permit erasure of the highlighted message.  
Add To Contacts — Save the sender’s number to your Contacts.  
Message Info — Shows message delivery status, addressee, size, and so on.  
Extract — Calls the sender of the received message.  
5. Use the Up/Down navigation keys to highlight an option. Press the OK  
key to perform the function for the highlighted option.  
Managing Inbox Messages  
1. In standby mode, press the Messages (Down navigation) key, then press  
for Inbox. A list of incoming messages appears in the display.  
2. Use the navigation keys to highlight a message in the list.  
3. Press the Erase (left) soft key (  
) to remove the highlighted message  
from the Inbox.  
Press the Options (right) soft key (  
). The following options appear in  
the display:  
Reply — Compose and send a reply message to the originator of the received  
message.  
Reply With Copy — Compose and send a reply message to the originator of  
the received message and include a copy of the original message.  
Forward — Send a copy of this message to another recipient.  
Lock / Unlock — Block/permit erasure of the highlighted message.  
Add To Contacts — Save the sender’s number to your Contacts.  
77  
Message Boxes  
Erase Inbox — Delete all unlocked messages from the Inbox.  
Message Info — Shows message delivery status, addressee, size, and so on.  
4. Use the Up/Down navigation keys to highlight an option. Press the OK  
key to perform the function for the highlighted option.  
Outbox  
Your phone stores messages in the Outbox, regardless of whether the message was  
successfully transmitted. Verify if and when a message or e-mail was successfully  
received by enabling the Enh. Delivery Ack/Delivery Ack feature.  
Review Messages in the Outbox  
1. In standby mode, press the Messages (Down navigation) key, then press  
for Outbox. Your list of sent messages appear in the display.  
2. Use the navigation keys to highlight a message that you wish to review,  
then press the OK key.  
3. While viewing your message press the Options (right) soft key (  
). The  
following options appear in the display:  
Forward — Send the highlighted message to another recipient.  
Save Quick Text — Save the message text as Quick Text for insertion into  
other messages.  
Lock / Unlock — Block/permit erasure of the highlighted message.  
Add To Contacts — Save the recipient’s number to your Contacts.  
Message Info — Shows message delivery status, addressee, size, and so on.  
4. Use the Up/Down navigation keys to highlight an option. Press the OK  
key to perform the function for the highlighted option.  
Messages and Lock Mode  
Your phone can still receive messages while in Lock Mode. The time and date of the  
message appear in the display, but you cannot access the message until you enter  
the lock code.  
Managing Outbox Messages  
1. In standby mode, press the Messages (Down navigation) key, then press  
for Outbox. Your list of sent messages appear in the display.  
2. Use the navigation keys to highlight a message.  
3. Press the Erase (left) soft key (  
) to remove the highlighted message  
from the Inbox.  
Press the Options (right) soft key (  
). The following options appear in  
the display:  
Messaging  
78  
           
Forward — Send the highlighted message to another recipient.  
Resend — Re-send the highlighted message to the original recipient.  
Lock / Unlock — Block/permit erasure of the highlighted message.  
Add To Contacts — Save the recipient’s number to your Contacts.  
Erase Outbox — Delete all unlocked messages from the Outbox.  
Message Info — Shows message delivery status, addressee, size, and so on.  
4. Use the Up/Down navigation keys to highlight an option. Press the OK  
key to perform the function for the highlighted option.  
Draft Box  
Messages in the Draft Box are those that have been composed but never sent. You  
can return to the Draft Box at any time to view, edit, or send a draft message.  
Create a Draft Message  
1. In standby mode, press the Messages (Down navigation) key, then press  
(for Send Message) and select one of the following Send  
Message options:  
Text Message  
Picture Message  
The Create Txt Msg screen or Create Pic Msg screen appears in the  
display showing the To: list.  
2. Enter the phone Number or E-Mail address of a recipient, then press the  
OK key.  
3. Compose your message using the keypad, then press the Options (right)  
soft key (  
).  
4. Use the Up/Down navigation keys to highlight Save As Draft, then press  
the OK key. A confirmation message appears in the display and your  
message is saved to the Drafts box.  
79  
     
Message Boxes  
View and Edit Draft Text Messages  
1. In standby mode, press the Messages (Down navigation) key, then press  
for Drafts. A list of any draft messages that you’ve saved appears  
in the display.  
2. Use the navigation keys to highlight a text message that you wish to view  
or edit, then press the EDIT key ( OK ). The message text edit screen  
appears in the display.  
3. Enter or change the recipient’s number and/or e-mail address and the  
information.)  
4. Press the Options (right) soft key (  
) to complete the message text and  
set message send options. The following options appear in the display:  
Preview — Picture Message — View the message as it will appear to the  
recipient(s).  
Edit Send To Text Message — Change, add, or remove recipients from this  
message.  
Add Quick Text — Insert pre-composed text into your message text.  
Save As Draft — Save the message to your Drafts box.  
Priority Level — Choose High or Normal.  
Validity Period — Enter the Date when this message will cease to be valid,  
then use the Left and Right navigation keys to choose the Time.  
Delivery Ack — Picture Message — Choose On or Off — Requests  
confirmation when your message is received.  
Enh. Delivery Ack Text Message — Choose On or Off — Requests  
confirmation when your message is received.  
Remove Pic — Picture Message — Remove the current picture from this  
message.  
Remove Sound — Picture Message — Remove the current sound file from  
this message.  
Add To Contacts — Save the recipient’s number or e-mail address to your  
Contacts.  
5. Use the Up/Down navigation keys to highlight the desired option, then  
press the OK key to perform the function for the highlighted option.  
6. When you have completed composing your message, press the OK key  
to send it.  
View and Edit Draft Pic. Messages  
1. In standby mode, press the Messages (Down navigation) key, then press  
for Drafts. A list of any draft messages that you’ve composed  
Messaging  
80  
appears in the display.  
2. Use the navigation keys to highlight the picture message that you wish to  
view, then press the EDIT key ( OK ). The message edit screen appears in  
the display.  
3. Make any needed changes and press the Options (right) soft key (  
).  
The following options appear in the display:  
Preview — Shows the message contents.  
Add Quick Text — Insert pre-composed text into your message text.  
Save As Draft — Saves the changed message to the Draft Box.  
Priority Level — Choose High or Normal.  
Validity Period — Enter the Date when this message will cease to be valid,  
then use the Left and Right navigation keys to choose the Time.  
Delivery Ack — Choose On or Off — Requests confirmation when your  
message is received.  
Remove Pic — Remove image included in draft message.  
Remove Sound — Remove sound file included in draft message.  
Add To Contacts — Save the recipient’s number or e-mail address to your  
Contacts.  
4. Use the Up/Down navigation keys to highlight an option. Press the OK  
key to perform the function for the highlighted option.  
Managing Draft Messages  
1. In standby mode, press the Messages (Down navigation) key, then press  
for Drafts. A list of any draft messages that you’ve composed  
appears in the display.  
2. Use the Up/Down navigation keys to highlight a message.  
3. Press the Erase (left) soft key (  
) to remove the highlighted message  
from the Drafts box.  
Press the Options (right) soft key (  
). The following options appear in  
the display:  
SEND — Send the highlighted message to the original recipient, if the  
recipient’s number and/or e-mail address is included with the draft message.  
Lock / Unlock — Block/permit erasure of the highlighted message.  
Add To Contacts — Save the recipient’s number and/or e-mail address to your  
Contacts.  
Save Quick Text — Save the message text as Quick Text for insertion into  
other messages.  
Erase Drafts — Delete all unlocked draft messages.  
81  
Message Boxes  
4. Use the Up/Down navigation keys to highlight an option. Press the OK  
key to perform the function for the highlighted option.  
Voicemail  
Messages in your voice mailbox are logged in the Voicemail box of the Messages  
menu. Open the Voicemail box to view the Callback # (if available), Urgency, and  
other details of the Voicemail message.  
Listen to Voicemail Now  
Once you’ve received a new voicemail message, you have the option to either:  
Listen Now — Calls your voice mailbox and allows you to listen to your  
messages.  
Listen Later — Returns you to standby mode where you can later choose to call  
your mailbox and review your messages.  
1. Use the Up and Down navigation keys to highlight the desired option, then  
press the OK key.  
Listen to Voicemail Later  
If you have chosen to review your voicemail messages at a later time:  
1. In standby mode, press the Messages (Down navigation) key, then press  
for Voicemail. The Voicemail screen appears in the display,  
showing the number of new voicemail messages received and the date  
and time the latest message was received.  
2. Press the  
to the message.  
key or the OK key to call your voice mailbox and listen  
Note: You can also press and hold  
to dial your voice mailbox.  
Messaging  
82  
     
Erase Messages  
You can erase all of the messages in each your boxes from one convenient location.  
Note: This function erases all messages in the selected box. To delete a single message, open the box from  
the Messages menu, then delete the message from the Options menu while viewing the message  
content.  
1. In standby mode, press the Messages (Down navigation) key), then press  
for Erase Messages. The following options appear in the display:  
Inbox — Deletes all unlocked messages stored in the Inbox.  
Outbox — Deletes all unlocked messages stored in the Outbox.  
Drafts — Deletes all unlocked messages stored in the Drafts box.  
All Messages — Deletes all unlocked messages stored in all of the message  
boxes, except Voicemail.  
2. Use the Up/Down navigation keys to highlight the box containing the  
messages that you wish to delete.  
3. Press the OK key. You’re prompted to confirm the erasure of all  
messages in the selected box or in all boxes.  
4. Press the Yes (left) soft key (  
) to delete the messages. Press the No  
(right) soft key (  
) cancel deleting the messages.  
Message Settings  
Use the Msg Settings sub-menus to define settings for general, text, and picture  
messages.  
General Message Settings  
1. In standby mode, press the Messages (Down navigation) key, then press  
(for Msg Settings) and  
appear in the display.  
for General. The following options  
Auto Save — Choose whether your messages are saved automatically when  
you exit them (On, Off, Prompt).  
Auto Erase Choose to receive (On) or not receive (Off) a warning message  
when you delete a message.  
Quick Text — Edit your pre-composed messages, which can then be inserted  
into new messages.  
Voicemail # — Edit or view your Voicemail number.  
Entry Mode — Choose the default method for entering text into messages (T9  
Word, Abc, ABC, 123).  
Callback # — Choose whether to include a callback phone number with your  
outgoing messages, and enter the number to be included.  
83  
             
Message Settings  
Signature — Choose whether to include a text signature in outgoing message  
text, and enter the text to be included.  
Reminder — Select whether and how often you will hear and/or feel a  
reminder that you have received a message (Once, Every 2 Minutes, Every  
15 Minutes, Off).  
2. Use the Up/Down navigation keys to highlight the desired option. Press the  
OK key to enter the highlighted option’s sub-menu.  
Editing and Entering Quick Text  
1. In standby mode, press the Messages (Down navigation) key, then press  
(for Msg Settings),  
(for General), and  
for Quick  
Text. The Quick Text sub-menu appears in the display.  
2. Use the Up/Down navigation keys to highlight a Quick Text you want to  
change, then press the OK key. (You cannot change the pre-defined  
Quick Text included with your phone.)  
Press the New (right) soft key (  
) to create a new Quick Text.  
Tip: You can also create new Quick Text by viewing/editing an Outbox message and using the Save Quick  
Text option in the Options menu. See “Review Messages in the Outbox” on page 78 for more  
information.  
3. Enter/change the text content of your Quick Text using the keypad. (See  
Press the Left soft key (  
) to change Text Input Mode.  
4. Once you’re finished entering your Canned Msg., press the OK key. The  
Quick Text menu appears in the display with your new Canned Msg.  
highlighted.  
Text Message Settings  
1. In standby mode, press the Messages (Down navigation) key, then press  
(for Msg Settings) and  
for Text Message. The following  
options appear in the display.  
Auto View — On/Off — With Auto View On, the full content of a text message  
appears in the display as the messages is received.  
Signature — Create a signature, which can be included at the bottom of  
outgoing message text.  
Auto Scroll — On/Off — With Auto Scroll On, the full content of a text  
message automatically rolls upward on the display, one screen-full at a time.  
2. Use the Up/Down navigation keys to highlight the desired setting. Press  
the OK key to enter the highlighted option’s sub-menu.  
Messaging  
84  
     
Picture Message Settings  
1. In standby mode, press the Messages (Down navigation) key, then press  
(for Msg Settings) and  
for Picture Message. The  
following options appear in the display.  
Auto Receive — On/Off — With Auto Receive On, Picture messages  
automatically download and display as they are received. With Auto Receive Off,  
you are prompted to download Picture messages.  
Signature — Create a signature, which can be included at the bottom of  
outgoing Picture message text.  
2. Use the Up/Down navigation keys to highlight the desired setting. Press  
the OK key to enter the highlighted option’s sub-menu.  
85  
   
MetroWEB  
Section 9: MetroWEB  
Topics Covered  
This section outlines how to launch MetroWEB, how to navigate to other pages on  
the web, and how the keys on the keypad are used with the web application.  
Additionally, links to other sites are briefly discussed.  
MetroWEB  
With MetroWEB, you can conveniently surf the web and download ringtones and  
wallpapers using your phone. Each time you launch MetroWEB, your phone connects  
to the Internet and the service indicator icon (  
) appears in the display.  
Stored Web Content  
MetroWEB ends an Internet connection after a certain period of inactivity, however  
some information from your session remains stored in the phone (if you leave your  
phone turned on). You can access this information without reconnecting to the  
Internet. However, if you are viewing stored information, and you select a link to a  
site that was not accessed in your last session, you automatically re-connect to the  
Internet.  
Launching MetroWEB  
1. Open the QWERTY keypad.  
Note: MetroWEB is only accessible using the QWERTY keypad.  
MetroWEB  
86  
         
2. In standby mode, do one of the following to launch MetroWEB:  
Press the Left navigation key.  
Press the MENU (left) soft key (  
for Get In Web.  
), then press  
(for MetroWEB) and  
3. A list of categories (each representing one or more web sites) appears in  
the display.  
4. Use the navigation keys to browse the categories.  
5. Once the desired category is highlighted, press the  
) to enter the category list.  
Exit MetroWEB  
(left) soft key  
(
To exit MetroWEB, press  
or close the QWERTY keypad.  
Using MetroWEB  
When you use MetroWEB, some of the keys operate differently than during a normal  
phone call. MetroWEB presents on-screen items in any of the following ways:  
Text or numeric input.  
Links (embedded in content).  
Numbered options (some may not be numbered).  
Simple text.  
You can act upon options or links by using the soft keys.  
MetroWEB soft keys  
At the bottom of the MetroWEB display is a bar that contains browser commands.  
The Left and Right (  
) soft keys on the keypad are used to execute the  
commands that appear in their respective corners of the display. These are called  
“soft keys” because their functions change depending on the application.  
Using Links  
Links have several purposes, such as jumping to a different page, to a different site,  
or even initiating a phone call. Links are shown inside of brackets ([ ]). You can  
normally use the Left soft key (  
) to select a link when it is highlighted.  
87  
         
How MetroWEB Keys Work  
How MetroWEB Keys Work  
The following table lists MetroWEB keys and their functions.  
navigation keys — Use to browse lists and options  
OK  
Back Key — A browse, back-up key. Press once to back up  
one page. Press and hold to go back to home page.  
Press to clear the last number, letter, or symbol entered. Press  
and hold to completely clear the display.  
SHIFT Key — Press before entering text to enable uppercase  
characters.  
Spacebar — Press to insert a space when entering text.  
Number 1 thru 0 — Use the number keys to select items in a  
menu if they are numbered.  
End Key — Press to exit the MetroWEB and return the phone  
to standby mode.  
Left Soft Key — Press to activate the command that appears  
above it in the display.  
Right Soft Key — Press to activate the command that  
appears above it in the display.  
MetroWEB  
88  
   
Section 10: Voice SVC  
Topics Covered  
This section explains how you can use and customize your phone’s VoiceSignal  
voice recognition feature.  
Note: Although the procedures in this section are written for the phone keypad, you can also perform these  
procedures using the QWERTY keypad.  
Voice SVC Options  
Your SCH-r410 includes VoiceSignal, state-of-the-art voice recognition software that  
lets you use your voice to dial numbers, access your Contacts list, and open Tools. To  
access your phone’s voice recognition, do the following:  
1. In standby mode, press the MENU (left) soft key (  
), then press  
for Voice SVC. The following options appear in the display:  
Voice Command — Lets you place calls, access your Contacts List, review  
your appointments, and more by speaking commands into your phone. Also see  
information.  
Voice Settings — Lets you tailor VoiceSignal to better respond to your voice  
information.  
2. Use the Up/Down navigation keys to highlight the desired sub-menu, then  
press the OK key.  
89  
     
Voice Command  
Voice Command  
To access the Voice Command menu, do one of the following:  
In standby mode, press and hold the  
key.  
Say a Command” appears in the display and is pronounced through the  
earpiece, followed by a list of available commands.  
In standby mode, press the MENU (left) soft key (  
Voice SVC) and for Voice Command.  
), then press  
(for  
Note: You can also set your phone to start VoiceSignal when you connect an optional headset to the phone.  
The following voice commands appear in the display:  
Call — Lets you dial the phone by saying any name stored in your contact list,  
without ever having to record, or “train” that name. VoiceSignal automatically  
voice-activates all your contacts, even if you have hundreds of them stored on  
your phone. You can also dial any telephone number, even if it is not stored in your  
contact list, by saying the digits in the number. (See “Voice Dialing” on page 24 for  
more information.)  
Send Text — Lets you access Create Text Message.  
Send Picture — Lets you access Create Picture Message.  
Lookup — Lets you find a Contact by name and review the Contact’s information.  
Go to — Lets you access the following list of your phone’s features and functions:  
Voice Memo  
Calendar  
Contacts  
Check — Lets you say a single command (such as “Status”) to verify your  
phone's: Status, Signal, Network, Battery, or My phone #.  
Note: Speaking clearly, say the command that you want to use. If VoiceSignal does not recognize a  
command, it prompts you to repeat the command. If VoiceSignal still does not recognized the  
command, it tells you “Sorry, no match found” and cancels voice recognition.  
Voice Command Tips:  
Make sure you wait for the beep before speaking.  
Speak clearly at a normal volume, as if you were talking on the phone.  
Voice SVC  
90  
 
Voice Settings  
Choice Lists  
When VoiceSignal cannot recognize a name or number, it displays a choice list of up  
to three possible choices, and prompts you to confirm the correct one.  
You can select how VoiceSignal will use choice lists with name dialing, digit dialing,  
and contacts.  
To change the way VoiceSignal uses choice lists:  
1. In standby mode, press the MENU (left) soft key (  
(for Voice SVC), (for Voice Settings), and  
Choice Lists.  
), then press  
for  
2. Use the Up/Down navigation keys to highlight the Choice List behavior you  
prefer:  
Automatic — VoiceSignal displays a choice list only when it is not sure if it has  
correctly recognized the name or number.  
Always On — VoiceSignal always displays a choice list, even when there is  
only one choice.  
Always Off — VoiceSignal never displays a choice list.  
3. Press the OK key or the OK (left) soft key (  
) to accept the new  
setting. Press the  
key to discard the new setting and return to the  
Voice Settings menu.  
Sensitivity  
1. In standby mode, press the MENU (left) soft key (  
(for Voice SVC), (for Voice Settings), and  
), then press  
for Sensitivity.  
2. Use the Up and Down navigation keys to adjust the selected Sensitivity  
setting incrementally between Reject More spoken commands or names  
and Reject Less spoken commands or names.  
3. Press the OK key or the OK (left) soft key (  
) to accept the new  
setting. Press the  
key to discard the new setting and return to the  
Voice Settings menu.  
Digit Dialing  
If you regularly have trouble with VoiceSignal not recognize the numbers you say, try  
adapting digit dialing to your voice. Adapting can improve the accuracy of digit  
recognition, especially for people with strong regional accents.  
91  
         
Voice Settings  
Note: After you adapt Digit Dial, your phone is customized to your voice, and your voice only. Others will not  
be able to use it unless they reset the phone to factory defaults.  
Adaptation involves recording several sequences of four digits each. The recording  
process takes about a minute.  
Tips for Adapting Digit Dialing  
Use Adapt Digits in a quiet place.  
Make sure you wait for the beep before starting to speak.  
Speak clearly, and say each digit distinctly.  
If you make a mistake while recording a sequence of digits, or if there is an  
unexpected noise that spoils the recording, re-record that sequence.  
Only adapt digits if you are regularly having problems with digit dialing. Once you  
adapt, digit dialing will not work as well for other people using your phone. (You  
can always reset digit adaptation to its original state, as described below.)  
Adapt Digits  
To adapt digit dialing, do the following:  
1. In standby mode, press the MENU (left) soft key (  
(for Voice SVC), (for Voice Settings), and  
Digit Dialing. The following options appear in the display:  
), then press  
for  
Adapt Digits  
Reset Digits  
2. Use the Up/Down navigation keys to highlight Adapt Digits, then press the  
OK key. Your phone displays text describing the Adapt Digits process.  
3. Press the OK key. Your phone displays the first digit sequence and  
Please say” plays through the speaker followed by the four digits  
appearing in the display.  
4. Wait for the beep and say the digits using your normal tone of voice. After  
a moment, the phone plays back the recording and prompts “Did the  
recording sound ok?”  
If the recording was good, say “Yes.”  
If you need to re-record, say “No.”  
If you say “No,” the phone prompts you to pronounce the digits again. Wait  
for the beep and then say the digits.  
Repeat this step until you’re satisfied with the recording.  
Voice SVC  
92  
5. After confirming that the recording sounds “ok”, continue the recording  
process with the next set of digits.  
6. After 10 sets of digits, the phone asks whether you want to do more  
adaptation. Answer “Yes.”  
7. Repeat steps 4 and 5 for another 10 sets of digits. After the second group  
of 10 sets of digits, “Adaptation complete” plays through the speaker and  
you are returned to the Digit Dialing menu.  
Reset Digits  
To reset digit dialing to factory default settings, do the following:  
1. In standby mode, press the MENU (left) soft key ( ), then press  
(for Voice SVC), (forfor Voice Settings), and for Digit  
Dialing. The following options appear in the display:  
Adapt Digits  
Reset Digits  
2. Use the Up/Down navigation keys to highlight Reset Digits, then press the  
OK key. The phone prompts you to confirm digit rest.  
3. Press the OK (left) soft key (  
) to reset your digit adaptation, or press  
) to cancel.  
the Back (right) soft key (  
Sound  
Sound lets you specify what (if any) text prompts you want your phone to read to you  
through the earpiece.  
1. In standby mode, press the MENU (left) soft key (  
), then press  
(for Voice SVC),  
(for Voice Settings), and  
for  
Sound. The following options appear in the display:  
Prompts — On/Off — Enables or disables audio prompts.  
Digits — On/Off — Enables or disables digit playback.  
Names — On/Off — Enables or disables name playback.  
Name Settings — Lets you adjust the Speed (Faster or Slower) and Volume  
(Louder or Softer) of your phone’s audio name playback.  
2. Use the Up and Down navigation keys to highlight the desired option, then  
press the OK key.  
3. Use the Up and Down navigation keys to highlight the desired setting.  
4. Press the OK key or the OK (left) soft key (  
) to accept the new  
setting. Press the  
key to discard the new setting and return to the  
Sound menu.  
93  
 
Voice Settings  
Voice Launch  
To set the key or action that launches VoiceSignal, do the following:  
1. In standby mode, press the MENU (left) soft key (  
(for Voice SVC), (for Voice Settings), and  
Launch. The following options appear in the display:  
), then press  
for Voice  
Key Only — Press and hold  
Key/EarMic — Attach a headset to your phone. Press and hold  
press and hold the button on the headset to activate VoiceSignal.  
to activate VoiceSignal for one call.  
or  
2. Use the Up/Down navigation keys to highlight the option you want, then  
press the OK key or the OK (left) soft key ( ) to save and exit. Press  
key to discard the new setting and return to the Voice Settings  
the  
menu.  
About  
This option causes the About VoiceSignal screen to appear in the display, showing  
version and build information about the VoiceSignal software included on your  
phone.  
1. In standby mode, press the MENU (left) soft key (  
), then press  
(for Voice SVC), (for Voice Settings), and  
for  
About.  
The About VoiceSignal screen appears in the display showing the version  
level of the VoiceSignal software currently installed on your phone.  
Voice SVC  
94  
     
Section 11: Multimedia  
Topics Covered  
Use your SCH-r410 phone to take full color digital pictures, display them on your  
phone’s vivid color display, and instantly share them with family and friends.  
With Mobile Shop, you can download personalized ringtones, pictures, and more.  
For more information, contact your Wireless Carrier.  
Note: Although the procedures in this section are written for the phone keypad, you can also perform these  
procedures using the QWERTY keypad.  
95  
   
Camera  
Camera  
Taking Pictures  
Taking pictures with the built-in camera is as simple as choosing a subject, pointing  
the lens [located on the outside of the folder (above the external display)], and  
pressing a button.  
Simple Snap Shot  
To take a single picture using the current camera settings, do the following:  
1. In standby mode, press the Camera key (  
) on the right side of the  
phone.  
The message “Loading...” followed by a camera viewfinder screen  
appears in the display. (See “Camera Screen” on page 97 for more  
information.)  
Note: You can also activate the camera (from standby mode) by press the MENU (left) soft key (  
),  
then press  
(for Multimedia) and  
for Camera.  
2. Point the camera lens at your subject.  
3. Using the display as a viewfinder, press the OK key when the image that  
you wish to capture appears in the display.  
4. Press the Save (left) soft key (  
) to save the picture to the Image gallery  
in your phone, a part of the phone’s memory devoted to storing, browsing,  
and viewing saved pictures.  
Press the SEND key ( OK ) to save the picture and include it in a Picture  
more information.)  
Press the Erase (right) soft key (  
) to erase the photo.  
Tip: You can change a number of the camera’s settings to suit particular uses for your pictures. See  
Multimedia  
96  
       
Camera Screen  
When you activate your phone’s camera, the second  
line of the display is reserved for the current camera  
resolution setting and the picture counter. The center  
of the display shows a viewfinder image of the  
subject at which the camera is pointed. The soft key  
labels on the bottom line of the display change to the  
following:  
My Images — Pressing the Left soft key (  
)
opens the My Images gallery so you can view or  
manage your stored pictures.  
TAKE — Pressing the OK key takes a  
picture of the image currently appearing on  
the display.  
Options — Pressing the Right soft key  
(
) opens a pop-up menu of camera  
settings.  
Camera Screen Icons  
Camera — Indicates that your phone is in Camera mode.  
Night Shot — Replaces the Camera icon. Indicates that your  
phone is ready to take photos in low light.  
Resolution — Indicates the current Resolution setting  
(640x480 shown).  
Brightness — Indicates the current photo Brightness  
setting [0 (no Brightness) shown]. The direction arrows  
indicate that the Up and Down navigation keys adjust the  
Brightness setting.  
Zoom — Indicates the current Zoom setting [0 (no Zoom)  
shown]. The direction arrows indicate that the Left and Right  
navigation keys adjust the Zoom setting.  
97  
       
Camera  
Memory Counter — Indicates the maximum number of  
photos you can take at the current Resolution and Quality  
settings.  
Quality — Indicates the current photo Quality setting (Fine  
shown).  
White Balance — Indicates the current photo White Balance  
setting (Auto shown).  
Self Timer — Delays the camera shutter by either 2, 5, or 10  
OK  
seconds after you press the  
key.  
Multi Shot — Automatically or manually  
takes multiple pictures in sequence after you  
OK  
press the  
key.  
Camera Shortcuts  
You can use the Navigation Keys to quickly access both the Brightness and Zoom  
capabilities of the built in camera. When you exit the camera mode, all camera  
settings return to default values.  
Brightness  
1. In camera mode, change the brightness of your pictures using the Up and  
Down navigation keys. Options are +4 – -4.  
2. Press the OK key to take the picture.  
Zoom in on a Subject  
Your camera has digital zoom capabilities of up to x2 with Resolution set to  
320x240, and up to x3 with Resolution set to 160x120.  
Note: Pictures may appear somewhat grainy as you zoom in; this is a normal result of digital enhancement.  
Note: The Zoom setting is affected by the Resolution setting (camera mode). With Resolution set to  
640x480, no zoom is available. With Resolution set to 320x240 and lower, Zoom settings 0 2 are  
available. With Resolution set to 160x120 and lower, Zoom settings 0 3 are available.  
1. In camera mode, press the Left and Right navigation keys to zoom in and  
out on your subject.  
2. Press the OK key to take the picture.  
Multimedia  
98  
           
Camera Options  
The Camera Options let you temporarily override your default camera settings. Any  
settings you change using the Camera Options only apply to the current camera  
session or until you make another change using the Camera Options.  
Delay Pictures with the Self Timer  
Self Timer lets you delay a picture long enough so you or the person taking the  
picture can join others in the picture.  
1. In camera mode, press the Options (right) soft key (  
). The following  
options appear in the display:  
Self Timer  
Multi Shot  
Quality  
Resolution  
White Balance  
Color Effects  
Settings  
2. Use the Left and Right navigation keys to highlight Self Timer. The  
following options appear in the display:  
Off  
2 Seconds  
5 Seconds  
10 Seconds  
3. Use the Up/Down navigation keys to highlight the desired delay, then press  
the OK key. The camera screen appears in the display.  
The next time you press the OK key, a countdown timer appears in the  
display that indicates the time remaining before the camera takes the  
picture.  
Multi Shot  
Multi Shot lets you take multiple pictures in succession at the touch of the TAKE key  
(
OK ).  
1. In camera mode, press the Options (right) soft key (  
menu bar appears in the display.  
). The options  
2. Use the Left and Right navigation keys to highlight Multi Shot. The  
following options appear in the display:  
Off  
On (3 pictures taken in succession).  
99  
         
Camera  
3. Use the Up and Down navigation keys to highlight the desired option, then  
press the OK key to save the option. The Multi Shot icon  
(
) appears in the display.  
The next time you press the OK key, the camera takes several pictures  
in rapid succession.  
Quality  
1. In camera mode, press the Options (right) soft key (  
menu bar appears in the display.  
). The options  
2. Use the Left and Right navigation keys to highlight Quality. The following  
options appear in the display:  
Fine  
Normal  
Economy  
3. Use the Up/Down navigation keys to highlight the desired picture quality  
setting, then press the OK key. The camera applies the selected Quality  
setting to your next picture.  
Resolution  
1. In camera mode, press the Options (right) soft key (  
menu bar appears in the display.  
). The options  
2. Use the Left and Right navigation keys to highlight Resolution. The  
following options appear in the display:  
480x640  
240x320  
120x160  
3. Use the Up/Down navigation keys to highlight the desired resolution  
setting, then press the OK key. The camera applies the selected  
Resolution setting to your next picture.  
White Balance  
White Balance allows you to adjust picture quality according to available light.  
1. In camera mode, press the Options (right) soft key (  
). The following  
options appear in the display:  
Self Timer  
Multi Shot  
Quality  
Resolution  
White Balance  
Multimedia  
100  
   
Color Effects  
Settings  
2. Use the Left and Right navigation keys to highlight White Balance. The  
following White Balance options appear in the display:  
Auto — The camera automatically adjusts picture quality to available light.  
Sunny — Use this setting when taking pictures in full sun.  
Cloudy — Use this setting when taking pictures in cloudy conditions.  
Tungsten — Use this setting when taking pictures under incandescent lights.  
Fluorescent — Use this setting when taking pictures under fluorescent lights.  
3. Use the Up/Down navigation keys to highlight one of the White Balances,  
OK  
then press the  
key, the camera applies the selected White Balance  
setting to your next picture.  
Color Effects  
Color Effects lets you change your pictures from full-color to two-color, (black plus a  
color you select).  
1. In camera mode, press the Options (right) soft key (  
). The following  
options appear in the display:  
Self Timer  
Multi Shot  
Quality  
Resolution  
White Balance  
Color Effects  
Settings  
2. Use the Left and Right navigation keys to highlight Color Effects, then  
press the OK key. The following Color Effects options appear in the  
display:  
Normal (full-color)  
Black&White (monochrome)  
Sepia  
Aqua  
Antique  
Negative  
Sketch  
Emboss  
101  
Camera  
3. Use the Up/Down navigation keys to highlight one of the Color Tones, then  
press the OK key, the camera applies the selected Color Tone setting to  
your next picture.  
Settings  
Camera Settings (unlike other Camera Options) do not return to their respective  
default values when you end the current Camera session. Instead, Camera Settings  
apply to future Camera sessions until you change individual Settings values or until  
you use Reset Settings.  
Shutter Sounds  
Choose from three different sounds whenever you take a picture. Aside from being a  
cool sound effect, Shutter Sounds acts as an audible reminder that your camera has  
taken the picture.  
1. In camera mode, press the Options (right) soft key (  
). The options  
menu bar appears in the display.  
2. Use the Left and Right navigation keys to highlight Settings.  
3. Use the Up and Down navigation keys to highlight Shutter Sound, then  
press the OK key. The following options appear in the display:  
Off — No Shutter Sound plays when you press the TAKE key ( OK ).  
Shutter  
OK  
Ding Dong  
4. Use the Up and Down navigation keys to highlight the desired Shutter  
OK  
Sound (each sound plays as it is highlighted) setting, then press the  
key. The camera applies the selected Shutter Sound setting to your next  
picture.  
Reset Settings  
1. In camera mode, press the Options (right) soft key (  
menu bar appears in the display.  
). The options  
2. Use the Left and Right navigation keys to highlight Settings.  
3. Use the Up and Down navigation keys to highlight Reset Settings, then  
press the OK key. The following options appear in the display:  
Off — Keeps the current camera settings.  
On — Resets the camera settings to default values.  
Night Shot  
Night Shot lets you take pictures in low light without a flash.  
Multimedia  
102  
   
Note: To avoid blurred pictures when taking Night Shots, hold your phone very steady for two seconds after  
pressing the TAKE key ( ).  
OK  
1. In camera mode, press the Options (right) soft key (  
). The options  
menu bar appears in the display.  
2. Use the Left and Right navigation keys to highlight Settings.  
3. Use the Up and Down navigation keys to highlight Night Shot, then press  
the OK key. The following options appear in the display:  
Off  
On  
4. Use the Up and Down navigation keys to highlight the Night Shot setting of  
your choice, then press the OK key. You’re returned to the camera  
viewfinder screen.  
Using My Images Gallery  
My Images lets you manage your photos and pictures you download, and lets you  
choose the pictures that appear in your phone’s display when you turn it on or off,  
while in standby mode (wallpaper), and as image IDs for your contacts.  
1. In standby mode, press the MENU (left) soft key (  
), then press  
(for Multimedia) and for My Images. A multiple-page matrix of  
thumbnail views of saved photos and images appears in the display.  
2. Use the navigation keys to highlight an image or photo.  
3. Press the Camera (left) soft key (  
) to take new photos.  
Press the VIEW key ( OK ) to expand the highlighted image to fill the  
screen.  
Press the Options (right) soft key (  
). The following options appear in  
the display:  
Send — Send to someone as part of a Picture message. (See “Send Picture  
Set As — Lets you set the highlighted image as the Main Wallpaper or as a  
Picture ID for one of your Contacts.  
Rename — Change the file name for the highlighted image.  
Lock / Unlock — Block/permit erasure of the highlighted image.  
Erase — Erase the highlighted image.  
Erase All — Erase all unlocked images from My Images.  
Photo Info — Shows the image file’s name, date and time, resolution, and size.  
103  
     
Using My Ringtones Gallery  
4. Use the Up/Down navigation keys to highlight an option, then press the  
OK key.  
5. Press the  
key to return to the previous menu, or press the  
key to return to standby mode.  
Using My Ringtones Gallery  
My Ringtones lets you assign ringtones for calls, alarms, and other alerts.  
1. In standby mode, press the MENU (left) soft key (  
), then press  
(for Multimedia) and  
for My Ringtones. A list of ringtones  
appears in the display.  
2. Use the navigation keys to highlight a ringtone.  
3. Press the Set As (left) soft key (  
) to assign the highlighted ringtone to  
be used as a Ringtone, Contact ID, or as an Alert Tone.  
Press the PLAY key ( OK ) to hear the ringtone.  
Press the Info (right) soft key (  
) to show title and file type for the  
highlighted ringtone.  
4. Press the  
key to return to the previous menu, or press the  
key to return to standby mode.  
Using My Sounds Gallery  
My Sounds lets you record and manage voice memo files and assign melodies as  
ringers or alerts.  
1. In standby mode, press the MENU (left) soft key (  
(for Multimedia) and for My Sounds.  
The following options appear in the display:  
), then press  
Record New — Lets you record voice memos.  
A list of recorded voice memo files and melodies.  
2. Use the navigation keys to highlight a file.  
3. When you highlight Record New and press the OK key, the Record  
New screen appears in the display.  
Press the REC key ( OK ) to start recording a voice memo.  
Press the Pause (left) soft key ( ) to pause/resume recording.  
Press the SAVE key ( OK ) to stop recording and save the voice memo.  
4. When you highlight a saved voice memo file, you have the following  
options:  
Multimedia  
104  
       
Press the Erase (left) soft key (  
is unlocked.  
) to erase the selected voice memo file, if it  
Press the PLAY key ( OK ) to listen to the voice memo.  
Press the Options (right) soft key (  
), and the following options appear in the  
display:  
SEND — Send to someone as part of a Picture message. (See “Send Picture  
Rename — Change the name of the voice memo file.  
Lock / Unlock — Block/permit erasure of the highlighted image.  
Erase all — Erase all unlocked voice memos.  
Sound Info — Shows the title, size, type, and date for the file.  
5. When you highlight a melody file, you have the following options:  
Press the PLAY key ( OK ) to hear the ringtone.  
Press the Options (right) soft key (  
) to show the following options:  
SEND — Send to someone as part of a Picture message. (See “Send Picture  
Set As — assign the highlighted ringtone to be used as a Ringtone, Contact  
ID, or as the Alert Tone.  
Erase all — Erase all unlocked melodies.  
Sound Info — Shows the title, size, type, and date for the file.  
6. Press the  
key to return to the previous menu, or press the  
key  
to return to standby mode.  
105  
Accessing Your Phone’s Tools  
Section 12: Tools  
Topics Covered  
This section explains how you can use your phone’s Personal Information Manager  
(PIM) functions to view today’s calendar, schedule appointments, set an alarm,  
perform simple math calculations, and more.  
Note: Although the procedures in this section are written for the phone keypad, you can also perform these  
procedures using the QWERTY keypad.  
Accessing Your Phone’s Tools  
To launch the Tools menu:  
In standby mode, press the MENU (left) soft key (  
), then press  
for Tools. The Tools menu appears in the display.  
Bluetooth  
Bluetooth is a short-range wireless communications technology capable of  
exchanging information over a distance of about 30 feet without requiring a physical  
connection.  
Tools  
106  
         
Unlike infrared, you don't need to line up the devices to beam information with  
Bluetooth. If the devices are within a range of one another, you can exchange  
information between them, even if they are located in different rooms.  
The Bluetooth wireless technology settings menu provides the ability to view and  
change the device name, show the visibility, and set the security for the device.  
Turn Bluetooth On/Off  
When the Bluetooth is turned on, you can use the Bluetooth features available. When  
the Bluetooth is turned off, you cannot send or receive information via Bluetooth. To  
save battery life or in situations where Bluetooth use is prohibited, such as airline  
traveling, you can turn off the Bluetooth wireless technology headset.  
To turn Bluetooth support on:  
From the Tools menu, press  
tooth Settings), and  
(for Bluetooth),  
for Enable.  
(for Blue-  
Bluetooth set to on” and the black Bluetooth On icon ( ) appear in the  
display.  
To turn Bluetooth support off:  
From the Tools menu, press  
tooth Settings), and  
(for Bluetooth),  
for Disable.  
(for Blue-  
Bluetooth set to off” appears in the display and the and the black  
Bluetooth On icon ( ) disappears.  
Add New Device  
To search for available Bluetooth devices:  
1. From the Tools menu, press  
for Bluetooth. The following options  
appear in the display:  
Add New Device  
Registered List  
Bluetooth Settings  
2. Highlight Add New Device and press the OK key.  
If Bluetooth is off, you are prompted to “Turn Bluetooth on?”. Press the Yes  
(left) soft key (  
) to turn Bluetooth on.  
Note: Press the No (right) soft key (  
) to leave Bluetooth off and return to the Bluetooth sub menu.  
Place device you are connecting to in discoverable mode” appears in  
the display.  
107  
 
Bluetooth  
3. Place the Bluetooth device in discoverable mode. (See the device user  
manual for more information.)  
4. Press the OK key. Names of the available devices appears in the  
display.  
5. Use the navigation keys to highlight the device you want to pair with your  
phone.  
6. Press the PAIR key ( OK ) to pair the selected device with the phone. You  
are prompted to enter the passkey or PIN for the selected device.  
7. Enter the device passkey or PIN and press the OK key. Pop-up  
messages appear to inform you that pairing with the device and  
connecting to it are complete.  
Registered List  
This menu provides a list of Bluetooth wireless  
technology devices discovered by your handset.  
1. From the Tools menu, press  
for  
Bluetooth. The following options appear in  
the display:  
Add New Device  
Registered List  
Bluetooth Settings  
2. Highlight Registered List and press the OK  
key. A list of registered Bluetooth devices appears in the display.  
Connecting to a Bluetooth Device  
From the Registered List,  
1. Highlight the device and press the OK key.  
2. If you are unable to connect with the device a pop-up appears in the  
display. Press the Yes soft key to retry.  
Disconnecting from a Bluetooth Device  
From the Registered List,  
Highlight the device and press the Off soft key.  
Tools  
108  
Managing Your Registered List  
From the Registered List,  
1. Highlight a device and press the Options soft key. The following options  
appear in the display:  
Remove Device — Deletes the device from the Registered List.  
Rename Device — Lets you change or replace the device name, as needed.  
Device Info — Shows the type of device, status, address, the date when it was  
paired with your phone, and the date the device was last connected with your  
phone.  
2. Highlight the desired option and press the OK key to access that option.  
Bluetooth Settings  
Enable/Disable  
Selecting this option turns Bluetooth on or off. (For more information, see "Turn  
Discovery Mode  
Allows other users to see your accessibility. Select On for other devices to see your  
device, or Off for no visibility.  
Device Name  
Shows the handset name. You may change this name. Enter the text and press the  
OK key.  
Device Info  
Shows the Bluetooth Type, Status, and Address of your phone.  
Calendar  
Calendar allows you to view the current, past, or future  
month in calendar format. While viewing the calendar,  
the current date is highlighted, and days with scheduled  
events are surrounded by a box.  
View an Event  
1. From the Tools menu, press  
for  
Calendar.  
109  
       
Calendar  
2. A calendar appears in the display with the current date highlighted. The  
month and year appear at the top of the display.  
3. Use the navigation keys to highlight different dates within the current  
month.  
Press OK to open a date that is highlighted.  
Press the Up volume key to view previous months.  
Press the Down volume key to view future months.  
4. Press the VIEW key ( OK ) to display a list of events on the highlighted  
date.  
5. Use the Up and Down navigation keys to highlight an event to view.  
6. Press the VIEW key ( OK ) to display the  
specifics of the highlighted event. The  
following options are available:  
Press the Edit (left) soft key (  
) to change  
the event details. (See “Add a New Event” on  
page 110 for more information.)  
Press the OK key ( OK ) to return to the Events  
list.  
Press the Options (right) soft key (  
following options appear in the display:  
). The  
Monthly — Returns you to the Monthly  
calendar display.  
Erase — Remove this event from the Calendar.  
Use the Up/Down navigation keys to highlight an option. Press OK to invoke  
the highlighted option.  
Add a New Event  
1. From the Tools menu, press  
for Calendar.  
A calendar appears in the display with the current date highlighted. The  
month and year appear at the top of the display.  
Tools  
110  
   
2. Press the Add (left) soft key (  
) to add an  
event. The New Event screen appears in the  
display.  
Use the Up and Down navigation keys to  
highlight New Event options.  
Use the Left and Right navigation keys to select  
option values.  
Use the keypad to enter option values.  
3. Enter the Name of the new event using the  
keypad.  
Press the Left soft key (  
) to change the text input mode. (See  
“Entering Text” on page 44 for more information.)  
Note: The current mode of text entry is indicated in the lower left corner of the display.  
4. To set the Start Date, use the keypad to enter the start date for the event.  
5. To set the Start Time:  
Use the keypad to enter the time for the event.  
Use the Left and Right navigation keys to select AM or PM.  
6. Repeat Steps 4 and 5 for the End Date and End Time.  
7. Use the Left and Right navigation keys to select:  
Alert type (Tone, Vibrate, Light Only)  
Alert tone (the Alert Tone screen appears in the display. See “Using My  
for more information.)  
Reminder (Off, Once, Every 2 Minutes, Every 15 Minutes)  
Alert time (15 Min. Before, 30 Min. Before, 1 Hour Before, 3 Hours Before,  
5 Hours Before, 1 Day Before, On Time, 5 Min. Before, 10 Min. Before)  
8. Press OK to store the event in your calendar. An alarm will notify you  
prior to the event, if Reminder is set to a value other than Off.  
111  
Memo Pad  
Memo Pad  
Create notes and store them in Memo Pad. Notes that  
you create in Memo Pad can’t be prioritized or assigned  
an alert. Return to Memo Pad anytime to review and edit  
your notes.  
Create a Memo  
1. From the Tools menu, press  
for  
Memo Pad.  
2. If you have any stored memos, they appear as  
a list in the display. If this is your first time in Memo Pad, press the Add  
(left) soft key ( ) to add a memo.  
3. Enter memo text using the keypad.  
Press the Left soft key (  
) to change the text input mode. (See  
Note: The current mode of text entry is indicated in the lower right corner of the display.  
4. Use the Up/Down navigation keys to highlight the entry mode that you  
wish to use, or press OK to exit the pop-up menu.  
Note: See “Entering Text” on page 44 for more information about entering text.  
5. When you’re finished entering details for the memo, press OK . The  
memo is stored.  
Review, Edit, and Erase Memos  
1. From the Tools menu, press  
for Memo Pad. Your list of stored  
memos appears in the display.  
2. Use the Up/Down navigation keys to browse memos.  
3. Press the Options (right) soft key (  
) and the following options appear  
in the display:  
Edit— Change the currently highlighted memo.  
Erase — Erase the highlighted memo.  
Erase all — Erase all of the unlocked memos.  
Lock / Unlock — Prevents/allows erasure of the highlighted memo.  
4. Press OK to VIEW a highlighted memo.  
Tools  
112  
   
5. Press the Edit (left) soft key (  
) to change the text of the memo you are  
viewing.  
Use the keypad to change the memo text. (See “Entering Text” on page 44  
for more information.)  
6. Press the Options (right) soft key (  
) while viewing a memo, and the  
following options appear in a pop-up menu:  
Erase — Erase the memo you are viewing.  
Add New Memo — Add a new memo to Memo Pad.  
Lock / Unlock — Prevents/allows erasure of the memo you are viewing.  
7. Use the Up/Down navigation keys to highlight an option.  
8. Press OK to perform the function for the highlighted option.  
Alarm Clock  
Your phone has three alarm clocks that can be set to go off once, or to recur daily at  
a specific time. Once set, an alarm clock is easy to change or turn off completely.  
Note: The alarm doesn’t function when the phone is turned off. If the time for an alarm that was set for  
Once has elapsed while the phone is off, the alarm occurs at the specified time on the next day.  
1. From the Tools menu, press  
for Alarm Clock. The following  
options appear in the display:  
Alarm 1  
Alarm 2  
Alarm 3  
2. Use the Up/Down navigation keys to highlight  
the alarm clock that you wish to set, then  
press OK . The selected Set Alarm screen  
appears in the display.  
Use the Up and Down navigation keys to  
select Set Alarm options.  
3. Use the Left and Right navigation keys to set  
the alarm Off or On.  
4. To set the Time:  
Enter the time for the alarm using the keypad.  
Use the Left and Right navigation keys to select AM or PM.  
5. Use the Left and Right navigation keys to select the Repeat at which you  
wish the alarm to occur (Daily, Mon.-Fri., Weekends, or Once).  
113  
   
Alarm Clock  
6. Use the navigation keys to select the Ringer type (Tone, Vibrate, Light  
Only) and ringtone (from My Ringtones or My Sounds).  
7. Press OK when you’re finished entering the time and frequency for the  
alarm. If the alarm is set to On, the alarm icon (  
) appears in the top of  
the display.  
When an Alarm Sounds  
An animated alarm clock appears in the display along with Snooze and Dismiss  
options and an alert sounds when the specified time for the alarm arrives.  
To silence the alarm, use the Navigation key to highlight Snooze or Dismiss and  
OK  
press  
.
If the alarm was set as a Daily alarm, the alarm icon remains in the top of the  
display.  
If the alarm was set as a Once only alarm, the alarm icon disappears from the top  
of the display.  
Turn Off the Alarm  
1. From the Tools menu, press  
for Alarm Clock. The following  
options appear in the display:  
Alarm 1  
Alarm 2  
Alarm 3  
2. Use the Up/Down navigation keys to highlight the desired alarm, then  
press the Options (right) soft key (  
). The following options appear in  
the display:  
On / Off  
Reset  
Reset All  
3. Use the Up/Down navigation keys to highlight Reset, then press OK .  
The selected alarm is turned off.  
Tools  
114  
   
World Time  
World Time lets you view the time of day or night in any  
of the 24 different time zones around the world.  
Note: To use World Time, you need to subscribe to your Wireless  
Provider’s digital service.  
1. From the Tools menu, press  
for  
World Time. A world map appears in the  
display.  
2. Use the Left and Right navigation keys to  
browse cities and their current times. The following cities are supported.  
EST/EDT : New York EST/EDT : Montreal EST/EDT : Boston  
Caracas  
Cape Verde  
Rome  
Brasilia  
London  
Mid Atlantic  
Paris  
Berlin  
Athens  
Moscow  
Tashkent  
Jakarta  
Seoul  
Helsinki  
Baku  
Jerusalem  
Abu Dhabi  
Bangkok  
Beijing  
Alma-ata  
Hong Kong  
Tokyo  
Guam  
Sydney  
Samoa  
Okhotsk  
Midway  
Wellington  
HAST/HADT :  
Honolulu  
HAST/HADT :  
Hawaii  
AKST/AKDT : Alaska PST/PDT : Seattle  
PST/PDT :  
San Francisco  
PST/PDT :  
MST/MDT : Denver  
MST/MDT : Arizona  
Los Angeles  
CST/CDT : Dallas  
CST/CDT : Chicago  
EST/EDT : Detroit  
CST/CDT : Houston  
CST/CDT :  
EST/EDT :  
Mexico City  
Washington D.C  
3. Do one of the following:  
Press the OK key to set the selected time zone as the default time zone for  
your phone.  
115  
     
Calculator  
Press the  
Enable Daylight Savings Time (DST)  
1. While viewing the World Time map, press the Options (right) soft key  
). DST Off / DST On pops-up in the display.  
2. Press the OK key to accept the highlighted setting. If the DST icon  
) appears in the display, it indicates that Daylight Savings Time is  
enabled.  
Calculator  
key to return to the Tools menu.  
(
(
You can perform calculations, including addition, subtraction, multiplication and  
division using your phone.  
1. From the Tools menu, press  
for Calculator. The Calculator  
appears in the display.  
2. Enter the first number in your equation using  
the keypad. (Numbers can be up to 9 digits  
long, and can include a decimal point followed  
by up to 2 more digits.)  
Press  
Press  
to a negative.  
to enter a decimal point.  
to change the sign for a number  
Press the Operator (right) soft key (  
) to add  
parentheses [( )] to your equation or to enter a  
Power exponent (^), such as, 3^2, which is the  
equivalent of 32.  
Press the Clear (left) soft key (  
) to clear current entries.  
3. Use the navigation keys (as shown in the Calculator screen) to set the  
type of calculation that you wish to perform. Your choices are as follows.  
[ + ] Addition  
[ x ] Multiplication  
[ - ] Subtraction  
[ ÷ ] Division  
4. Use the keypad to enter the second number into your equation.  
5. Press OK to perform the calculation and view the result.  
Tools  
116  
     
Stop Watch  
You can use this function to set a stop watch.  
1. From the Tools menu, press  
for Stop  
Watch. The Stop Watch screen appears in  
the display.  
2. Press the OK key to start, stop, and resume  
the stopwatch count.  
3. Press the Record (left) soft key (  
) at the  
start of each succeeding event/lap to record  
the completion time for the previous event/lap. You can record up to eight  
event/lap times.  
4. Press the Reset (right) soft key (  
) to reset the stop watch and to erase  
all stop watch (lap) times recorded.  
117  
 
Converter  
Converter  
The conversion menu provides the following conversion categories:  
Currency  
Length  
Weight  
Volume  
Area  
Temperature  
To convert a currency, length, weight, volume, area, or temperature, do the  
following:  
1. From the Tools menu, press  
for Converter. The following list of  
converters appears in the display:  
Currency  
Length  
Weight  
Volume  
Area  
Temperature  
2. Use the Up/Down navigation keys to highlight  
the conversion feature you wish to use, then  
press the OK key.  
3. Use the Navigation key to highlight and select  
the units to be converted From and To.  
4. Enter the quantity you want converted in the  
From field. The converted quantity appears in  
the To field.  
Note: To include a decimal point, press the  
key.  
Currency — Reviewing/Editing Exchange Rates  
The Currency Converter includes long-term average exchange rates as default  
values. To review and/or change a default exchange rate to the current exchange  
rate, do the following:  
1. From the Tools menu, press  
(for Converter), and  
for  
Currency.  
Tools  
118  
 
2. Press the Rate (left) soft key (  
). The EXCHANGE RATE list appears in  
the display.  
3. Press the EDIT key ( OK ). The EDIT  
EXCHANGE RATE list appears in the display.  
4. Use the Up and Down navigation keys to  
highlight a currency whose exchange rate you  
wish to change.  
5. Use the keypad keys to change the selected  
exchange rate value.  
6. Press the OK key to save the changed  
exchange rate. The EXCHANGE RATE list  
appears in the display.  
7. To change any other exchange rates, repeat Steps 3 – 6.  
8. Press the  
key to return to the Converter screen.  
Currency — Adding Exchange Rates  
You can use the Currency Converter to convert from and to obscure currencies by  
adding exchange rates for these currencies. To add a currency and its exchange rate  
to the Currency Converter, do the following:  
1. From the Tools menu, press  
(for Converter), and  
for  
Currency.  
2. Press the Rate (left) soft key (  
). The  
Exchange Rate list for the From currency  
appears in the display.  
3. Press the Add (left) soft key (  
). The Add  
Exchange Rate screen appears in the display  
with the Base field highlighted.  
4. Use the Left and Right navigation keys to  
select the Base currency to be converted  
from.  
5. Press the Down navigation key to highlight the  
Currency field.  
6. Enter an identifier of up to 5 characters for the new currency using the  
7. Press the Down navigation key to highlight the Exchange Rate field.  
8. Enter a decimal exchange rate for the new currency using the keypad.  
119  
Tip Calculator  
Note: Press the  
key to enter the decimal point.  
The Exchange Rate field only accepts up to five digits after the decimal point.  
9. Press the OK key to save the new exchange rate.  
Currency — Erasing Exchange Rates  
You cannot erase the preloaded currencies from the Exchange Rate list. You can  
erase a currency that you have added to the list by doing the following:  
1. From the Tools menu, press  
(for Converter), and  
for  
Currency.  
2. Press the Rate (left) soft key (  
). The Exchange Rate list for the From  
currency appears in the display.  
3. Use the Up and Down navigation keys to highlight the user-added currency  
exchange rate to be erased.  
4. Press the Erase (right) soft key (  
). You are prompted to confirm the  
erasure.  
Note: The Erase right soft key (  
) is undefined for preloaded Exchange Rates. This prevents you from  
erasing them.  
5. Press the Yes (left) soft key (  
press the No (right) soft key (  
) to erase the selected exchange rate or  
) to return to the Exchange Rate list.  
Tip Calculator  
Tip Calculator automatically calculates the following amounts:  
Gratuity (tip)  
Individual payment (for groups)  
Calculations are based on the total amount of the check, a selected gratuity  
percentage, and the number of people paying.  
1. From the Tools menu, press  
for Tip Calculator. The Tip Calculator  
screen appears in the Bill field is highlighted.  
Tools  
120  
 
2. Use the keypad to enter the total amount of  
the bill.  
3. If needed, press the Down navigation key to  
highlight the Tip field.  
4. Use the keypad to enter a tip percentage.  
5. If needed, press the Down navigation key to  
highlight the # Paying field.  
6. Use the keypad to enter the number of  
persons paying.  
7. The amount of the Tip, the bill Total, and the amount Each person should  
pay appear in the lower half of the screen.  
121  
Accessing Your Phone’s Settings  
Section 13: Settings  
Topics Covered  
This section explains how to configure your phone’s language, network  
preferences, security options, and other settings.  
Note: Although the procedures in this section are written for the phone keypad, you can also perform these  
procedures using the QWERTY keypad.  
Accessing Your Phone’s Settings  
To launch the Settings menu:  
In standby mode, press the MENU (left) soft key (  
), then press  
for Settings.  
The Settings menu appears in the display.  
Location Setting  
You can set your phone to pass Global Positioning System (GPS) data to identify your  
location to the network continually or only when you make an emergency (911) call.  
Note: Check with your Wireless Carrier to determine if/when/where location-based services are available.  
Settings  
122  
             
1. From the Settings menu, press  
for Location. The following  
Location options appear in the display:  
Location On — Your location data is continually sent wherever the feature is  
available.  
911 Only — Your location data is sent only when you dial 911.  
2. Use the Up/Down navigation keys to highlight an option.  
3. Press OK to select the function. The Settings menu appears in your  
display.  
4. Press  
to return to standby mode.  
Display Settings  
Display settings let you change your phone’s menu appearance, display brightness  
and contrast, and display content to better meet your needs.  
1. From the Settings menu, press  
for Display Settings. The  
following menus appear in the display:  
Wallpaper — Choose the images that appear as background in the Main  
display on your phone while in standby mode.  
Clock Format — Choose whether the time and date appear in the Main and  
Front displays on your phone in optional digital or analog (clock face) style or in  
the default digital style.  
Theme — Choose the color set used to show menus and screens on your  
phone’s display.  
Dialing Font — Lets you select the style and size of the font used to display  
digits you dial.  
Banner — Lets you change or replace the text greeting that appears in the  
display when your phone is in standby mode. Also lets you enable/disable an ERI  
(Extended Roaming Indicator) banner.  
Backlight — Set backlight options for the Main Display, Keypad, and backlight  
Brightness.  
2. Use the Up/Down navigation keys to highlight a sub-menu.  
3. Press the OK key to enter the highlighted sub-menu. The following  
sections describe the Display sub-menus in greater detail.  
Wallpaper  
Wallpaper lets you choose images that appear in the background on your phone’s  
Main display while in standby mode.  
123  
     
Display Settings  
1. From the Settings menu, press  
(for Display Settings), and  
for Wallpaper. The following options appear:  
My Images — Lets you select an image that you’ve downloaded or a picture  
you’ve taken with the camera.  
Preset Images — Lets you select an image that came preloaded with your  
phone.  
2. Use the Up/Down navigation keys to highlight the image type that you wish  
to use and press the OK key. A list of images appears in the display.  
3. Use the navigation keys to highlight the image that you wish to use and  
press the OK key to save your selection.  
Clock Format  
Lets you choose whether the time and date appear in the Main display on your  
phone in optional digital or analog (clock face) style or in the default digital style.  
1. From the Settings menu, press  
(for Display Settings), and  
for Clock Format.  
The following clock format options appear in the display:  
Digital — Time, date, and day of the week are shown using an alternate, large  
digital format.  
Analog — Time is shown using an analog clock face image.  
Off — Time, date, and day of the week are shown using the default, small  
digital format.  
2. Use the navigation keys to highlight the image that you wish to use and  
press the OK key to save your selection.  
Theme  
Lets you select the colors used to show menus and screens in the Main display.  
1. From the Settings menu, press (for Display Settings), and  
for Theme. The following options appear in the display:  
2. Use the Left and Right navigation keys to show the desired color theme  
(which appears in the preview screen), then pressed the OK key to save  
the selected theme setting.  
Settings  
124  
 
Dialing Font  
Lets you select the style and color of your dialing font.  
1. From the Settings menu, press  
for Dialing Font. The following sub-menus appear in the display:  
Style — Choose the font used to show phone number digits when you enter  
(for Display Settings), and  
them to be dialed.  
Size — Choose the size of the digits.  
2. Use the Up and Down navigation keys to highlight the desired dialing font  
characteristic, then press the OK key.  
If you select Style, the following Style options appear in the display:  
Normal  
Quill Pen  
Sticky  
Color Dial  
Use the Left and Right navigation keys to highlight the desired setting and press  
the OK key to save the selected setting.  
If you select Size, the following Size options appear in the display:  
Enable Zoom-out  
Disable Zoom-out  
Use the Up and Down navigation keys to highlight the desired setting and press  
the OK key to save the selected setting.  
Banner  
Create your own personalized greeting that appears in the display while your phone  
is in standby mode.  
1. From the Settings menu, press  
for Banner. The following sub-menus appear in the display:  
Personal  
ERI Banner  
(for Display Settings), and  
2. Use the Up and Down navigation keys to highlight the desired banner, then  
press the OK key.  
If you select Personal, the Banner screen appears in the display with the Enter  
Text field highlighted.  
Enter a word or short phrase to appear in your phone’s display while in standby  
mode (Up to 13 characters). See “Entering Text” on page 44 for more  
information.  
Tip: Press and hold  
to erase an existing banner, if necessary.  
125  
   
Sound Settings  
Press the OK key to save your changes.  
If you select ERI Banner, the following options appear in the display:  
On  
Off  
Use the Up and Down navigation keys to highlight the desired option, then press  
the OK key.  
Backlight  
You can set the backlight for your display or keypad to remain on for a specified  
period of time or remain on as long as the folder is open.  
Note: Prolonged backlight use drains your battery faster.  
1. From the Settings menu, press  
(for Display Settings), and  
for Backlight.  
The following sub-menus appear in the display:  
Main Display — Sets the time the internal display backlight remains on after a  
period of inactivity. Optional settings are: 7 seconds, 15 seconds, 30 seconds,  
Always On, and Always Off.  
Keypad — Sets the amount of time the keypad backlight remains on after a  
period of inactivity. Optional settings are: 7 seconds, 15 seconds, 30 seconds,  
Always On, and Always Off.  
Brightness — Use the Left and Right navigation keys to select between any of  
5 optional settings.  
2. Use the Up and Down navigation keys to highlight the desired sub-menu  
and press the OK key.  
3. Use the navigation keys to change settings as desired in the selected sub-  
menu, and press the OK key to save your selection.  
Sound Settings  
Sound Settings let you customize your phone’s audio properties, such as ringers,  
keypad tones, alerts, start up melody, and more.  
Settings  
126  
   
Volume  
Use the Volume sub-menu to set the default volume for call ringers, message alerts,  
and alarms.  
1. From the Settings menu, press  
(for Sound Settings), and  
for Volume. The following options appear in the display:  
Voice Calls — Lets you set your phone to be silent, play a sound, and/or vibrate  
in response to incoming calls.  
Messages — Lets you set your phone to be silent, play a sound, and/or vibrate  
in response to incoming messages.  
Alarms — Lets you set your phone to be silent, play a sound, and/or vibrate in  
response to a preset alarm time being reached.  
Key Tone — Lets you adjust the volume level of the tones that the keypad  
generates when you press the keys.  
2. Use the Up and Down navigation keys to highlight the desired option, then  
press the OK key.  
3. Use the Navigation key or the Up and Down volume keys on the right side  
of your phone to select the volume level (Ringer Off, Low, Low/Medium,  
Medium, Medium/High, or High) or vibrate mode (Vibrate, Vibrate/High)  
for the selected option.  
4. Press the OK key to save the option setting.  
Ringer Type  
You can assign ring tones and melodies for calls, alarms, and other alerts in the  
Ringer Type sub-menu.  
1. From the Settings menu, press  
for Ringer Type. The following ringer types appear in the display:  
Voice Calls  
(for Sound Settings), and  
Messages  
Text Message  
Picture Message  
Voicemail  
Roam Ringer  
2. Use the Up/Down navigation keys to highlight a ringer type, then press the  
OK key. The following ringtone options appears in the display:  
My Ringtones  
My Sounds  
3. Use the Up and Down navigation keys to highlight the desired ringtone  
gallery, then press the OK key.  
127  
     
Call Settings  
4. Use the Up and Down volume keys to scroll through the ringer types and  
melodies for the selected ringer type. Press the Play (left) soft key (  
)
to play each tone or melody as you scroll through the list.  
5. When the desired ringer type plays, press the OK key to save your  
selection.  
Alerts  
You can set your phone to sound an alert whenever you enter or leave your service  
area, connect or disconnect a call, and other options.  
1. From the Settings menu, press  
(for Sound Settings), and  
for Alerts. The following options appear in the display:  
Minute Beep — Sound an alert ten seconds before each elapsed minute of a  
call.  
Roaming — Sound an alert when you leave your home service area while on a  
call.  
Call Connect — Sound an alert when you connect/disconnect a call.  
Power On/Off — Play power on and power off melodies.  
2. Use the Up/Down navigation keys to highlight a sub-menu, then press the  
OK key. The following options appear in the display:  
On  
Off  
3. Use the Up and Down navigation keys to highlight active (On) or inactive  
(Off) for the selected alert.  
4. Press the OK key to confirm your selection.  
Call Settings  
The Call Settings sub-menu lets you set call options such as Auto Retry, Data rates  
for data calls, and more.  
Call Answer  
You can select a specific answer mode when you receive an incoming call. Your  
phone can be preset to answer when you do any of the following:  
1. From the Settings menu, press  
(for Call Settings), and  
for Call Answer. The following call answer options appear in the display:  
Any Key — Pressing any key except the  
Send Key — Only pressing answers a call.  
key or key answers a call.  
2. Use the Navigation key to highlight an option.  
3. Press the OK key to select the method for answering calls.  
Settings  
128  
     
Auto Answer  
Auto Answer enables your phone to automatically answer calls after a period of time  
that you specify.  
1. From the Settings menu, press  
(for Call Settings), and  
for Auto Answer. The following options appear in the display:  
Off  
After 1 Second  
After 3 Seconds  
After 5 Seconds  
2. Use the Up/Down navigation keys to highlight the desired setting, then  
press the OK key.  
Auto Retry  
Auto Retry automatically re-dials a number if there is no answer or the dialed party is  
busy. Depending upon your location, the number of times your phone redials a  
number may vary.  
1. From the Settings menu, press  
(for Call Settings), and  
for Auto Retry. The following options appear in the display:  
Off  
Every 10 Seconds  
Every 30 Seconds  
Every 60 Seconds  
2. Use the Up/Down navigation keys to highlight the desired setting, then  
press OK .  
TTY Mode  
Your phone is fully Teletypewriter (TTY)/Telecommunication Device for the Deaf (TDD)  
compatible. You connect TTY/TDD equipment to the headset connector on the top of  
your phone, behind the folder hinge.  
Note: TTY Mode must be enabled (TTY Full selected) before you can use your phone with TTY/TDD  
equipment.  
1. From the Settings menu, press  
(for Call Settings), and  
for TTY Mode. A message pops-up warning of possible headset and non-  
TTY accessory performance impairment when in TTY mode and prompting  
you to confirm that you want to enable/disable TTY Mode.  
Press the Yes (left) soft key (  
setting.  
) to confirm you want to change the TTY Mode  
129  
     
Call Settings  
Press the No (right) soft key (  
) to keep the current TTY Mode setting.  
2. The following options appear in the display:  
TTY Full — Enables TTY mode while letting you hear and speak with the other  
party.  
TTY + Talk — Enables TTY mode while letting you speak with the other party.  
TTY + Hear — Enables TTY mode while letting you hear the other party.  
TTY Off — Disables TTY mode.  
Note: The TTY Mode option has no effect on the phone’s earpiece, microphone, or speaker. When you  
select TTY Full, all currently enabled sound functions remain enabled.  
3. Use the Up/Down navigation keys to highlight your selection and press the  
OK key. You’re returned to the previous menu and the TTY icon (  
)
appears in the top of the display.  
Voice Privacy  
Voice Privacy lets you choose what level of voice security (Standard or Enhanced)  
your phone will use.  
Tip: You can change your Voice Privacy setting during a call by using the In-Use Menu options. (See “In-  
Use Menu” on page 29 for more information.)  
1. From the Settings menu, press  
(for Call Settings), and  
for Voice Privacy. The following options appear in the display:  
Standard  
Enhanced  
2. Use the Up/Down navigation keys to highlight the Voice Privacy option of  
your choice, then press the OK key.  
Data Settings  
Use the Data Settings sub-menu to set your phone to detect data connections  
automatically.  
1. From the Settings menu, press  
(for Call Settings), and  
for Data Settings. The following options appear in the display:  
Data Off — Your phone ignores data connections.  
Data For Next Call — Your phone accepts data connection for the next call.  
Data Until Powered Off — Your phone accepts data connections until you turn  
off your phone.  
2. Use the Up/Down navigation keys to highlight the desired data setting,  
then press the OK key.  
Settings  
130  
   
DTMF Tones  
Use this menu to set DTMF settings to Normal, or Long.  
1. In standby mode, press  
(for Call Settings), and  
for DTMF  
Tones. The following options appear in the display:  
Normal — Select for a normal tone  
Long Select for an extended tone  
2. Use the Up and Down navigation keys to highlight the DTMF Tones setting  
of your choice, then press OK . Your setting is saved.  
Phone Settings  
Airplane Mode  
When set to On, Airplane Mode disables all radio functions of your phone. This  
prevents you from making or receiving calls, but allows you to use other features  
(such as the camera and the Tools) safely in sensitive environments, such as on  
board an aircraft.  
1. From the Settings menu, press  
(for Phone Settings), and  
for Airplane Mode. The following options appear in the display:  
On — Disables the radio transmitter and receiver and the Bluetooth interface in  
your phone.  
Tip: If you need to make an emergency call with Airplane mode enabled, just dial the emergency number  
and press  
.
Off — Enables the radio transmitter and receiver in your phone.  
Note: Press  
to return to the Phone Settings menu.  
2. Use the Up/Down navigation keys to highlight the desired option, then  
press the OK key. You are prompted to confirm your setting change.  
3. Press the Yes (left) soft key (  
) to change to the new setting. Press the  
No (right) soft key (  
) to discard the change and keep the original  
setting.  
4. If you press Yes, you are returned to standby mode. If you press No, the  
Airplane Mode screen remains in the display.  
Language  
The Language option changes the language of menus, sub-menus, and other user-  
interface features.  
131  
     
Phone Settings  
1. From the Settings menu, press  
(for Phone Settings), and  
for Language.  
The following options appear in the display:  
English  
Español  
2. Use the Up/Down navigation keys to highlight your language preference,  
then press the OK key.  
Security  
Use the Security sub-menu to lock your phone, set up emergency numbers, enable  
or disable voice privacy, set restrictions, and other security options.  
Lock Phone  
Locking the phone blocks all outgoing calls except those to 911 and to the three  
user-programmed emergency numbers. You can lock the phone manually, or set the  
phone to lock automatically when turned on. In Lock mode, you can answer calls,  
but you must unlock the phone to place calls (except to emergency and secret  
numbers).  
Important!: If you change the NAM1 setting after setting the phone to lock upon power-up and did not  
program a number into NAM2, you won’t be able to access your phone. You must call the  
Service Center to unlock your phone.  
1. From the Settings menu, press  
(for Phone Settings), and  
for Security.  
The “Enter Code” prompt appears in the display.  
2. Enter the four-digit lock code using the keypad.  
Note: The default lock code is the last four digits of your mobile phone number.  
The “Enter Code” prompt disappears and the Security menu appears in  
the display.  
3. Press  
display:  
for Lock Phone. The following options appear in the  
Lock — The phone locks immediately and stays locked until you enter the lock  
code.  
Unlock — The phone remains unlocked.  
On Power Up — The phone locks automatically the next time your phone is  
powered on and stays locked until you enter the lock code.  
Settings  
132  
   
4. Use the Up/Down navigation keys to highlight the Lock Phone option of  
your choice.  
5. Press OK to perform the function for the highlighted option.  
Change Lock  
The default lock code is generally the last four digits of your phone number. It is  
advisable to change the default lock code to a secret code for security purposes.  
1. From the Settings menu, press  
(for Phone Settings), and  
for Security.  
The “Enter Code” prompt appears in the display.  
2. Enter the four-digit lock code using the keypad.  
Note: The default lock code is the last four digits of your mobile phone number.  
3. Press  
for Change Lock.  
The “New Lock Code” prompt appears in the display.  
4. Enter the New Lock Code. You’re prompted to re-enter the New Lock Code  
for verification.  
5. Enter the new lock code again. Your changes are stored.  
Note: Your phone does not allow you to view the lock code for obvious security reasons. If you change the  
lock code, be sure to write down or memorize the new code.  
Emergency #  
You have the option of storing up to three emergency numbers to your phone. Each  
number can be up to 32 digits in length. All emergency numbers can be dialed any  
time, even when your phone is locked or restricted.  
Note: Emergency number 911 is hard-coded into your phone. You can dial this number any time, even  
when the phone is locked or restricted. If you call 911 an audible tone is heard and an Emergency  
prompt appears in the display for the duration of the call.  
Important!: Because of various transmission methods, network parameters, and user settings used to  
complete a call from your wireless phone, a connection cannot always be guaranteed.  
Therefore, emergency calling may not be available on all wireless networks at all times.  
Important!: DO NOT depend on this phone as a primary method of calling 911 or for essential or  
emergency calls.  
133  
       
Phone Settings  
Remember to always turn your phone on and check for adequate signal strength  
before placing a call.  
Note: When you dial an emergency number, you phone locks itself to the emergency location that  
answered the call and locks itself in 911-Only mode, blocking from dialing any number but an  
emergency number.  
Store Emergency Numbers  
1. From the Settings menu, press  
(for Phone Settings), and  
for Security.  
The “Enter Code” prompt appears in the display.  
2. Enter the four-digit lock code using the keypad.  
Note: The default lock code is the last four digits of your mobile phone number.  
The “Enter Code” prompt disappears and the Security menu appears in  
the display.  
3. Press  
for Emergency #.  
, or  
4. Press  
,
to select one of the three emergency  
numbers.  
5. Enter the emergency number (up to 32 digits in length).  
6. Press OK to save the number that you entered.  
7. Press Cancel (right) soft key (  
) to discard your entry and return to the  
previous menu.  
Call Emergency Numbers in Lock Mode  
1. In standby mode, enter the emergency number via the keypad.  
2. Press  
to place the call.  
Reset Phone  
Reset Phone returns all setup parameters (except for the Contacts entries) to their  
factory default values.  
Caution!: Before selecting Reset Phone, contact your Wireless Carrier. Invoking Reset Phone may erase  
settings made by your Wireless Carrier from your phone, resulting in loss of service.  
1. From the Settings menu, press  
(for Phone Settings), and  
for Security.  
The “Enter Code” prompt appears in the display.  
Settings  
134  
     
2. Enter the four-digit lock code using the keypad.  
Note: The default lock code is the last four digits of your mobile phone number.  
The “Enter Code” prompt disappears and the Security menu appears in  
the display.  
3. Press  
default settings (except for Contacts).  
4. Press the Yes (left) soft key ( ) to reset your phone to factory default  
settings. Press the No (right) soft key ( ) to keep the current settings.  
Erase All Entry  
for Reset Phone. A prompt appears in the display to restore  
Erase All Entry deletes all entries from the Contacts list.  
1. From the Settings menu, press  
(for Phone Settings), and  
for Security.  
The “Enter Code” prompt appears in the display.  
2. Enter the four-digit lock code using the keypad.  
Note: The default lock code is the last four digits of your mobile phone number.  
The “Enter Code” prompt disappears and the Security menu appears in  
the display.  
3. Press  
for Erase All Entry.  
The “Enter Code” prompt reappears in the display.  
4. Enter the four-digit lock code using the keypad.  
Note: The default lock code is the last four digits of your mobile phone number.  
The “Enter Code” prompt disappears, and the “Erase all entries?”  
prompt appears in the display.  
5. Press the Yes (left) soft key (  
(right) soft key ( ) to keep the current Contacts entries.  
Restriction  
) to reset your Contacts list. Press the No  
Restriction lets you restrict the use of your phone for outgoing calls, incoming calls,  
and calls placed by/to your Contacts.  
1. From the Settings menu, press  
(for Phone Settings), and  
for Security.  
135  
   
Phone Settings  
The “Enter Code” prompt appears in the display.  
2. Enter the four-digit lock code using the keypad.  
Note: The default lock code is the last four digits of your mobile phone number.  
The “Enter Code” prompt disappears and the Security menu appears in  
the display.  
3. Press  
for Restriction.  
4. Use the Up/Down navigation keys to highlight Outgoing or Incoming.  
5. Press the OK key. The following options appear in the display:  
Allow All — No restriction on selected calls.  
Allow None — Restrict (block) all selected calls.  
Allow Contacts — Restrict selected calls from/to numbers not in your  
Contacts list.  
Note: The default restriction settings are all Off.  
6. Use the Up/Down navigation keys to highlight the Restriction you want,  
then press the OK key.  
NAM Selection  
NAM Selection allows you to set your preferred system. Contact your wireless  
carrier for more information.  
1. From the Settings menu, press  
(for Phone Settings), and  
for NAM Selection.  
The following NAM options appear in the display:  
NAM 1 — Your service contract has one phone line.  
NAM 2 — Your service contract has two phone lines.  
2. Use the Up/Down navigation keys and to highlight NAM 1 or NAM 2, the  
press OK to save your selection.  
The phone automatically restarts.  
System Select  
The System Select feature enables you to automatically or manually select the  
network used when roaming outside of your home area.  
1. From the Settings menu, press  
(for Phone Settings), and  
for System Select. The following roaming options appear in the  
display:  
Settings  
136  
MetroPCS only — Roaming is off. If your home system is not available then  
your call will not be connected, and the no service icon ( ) appears in the  
display. In some service areas, an operator may come on-line and ask you how  
you would prefer to pay for the call.  
Automatic — Roaming is on. It will always try your calls using the Preferred  
Roaming List (PRL) loaded into your phone. If a preferred service is not found,  
then this option will attempt to acquire any digital service.  
2. Use the Up/Down navigation keys and to highlight the desired Roam  
option, the press OK to save your selection.  
The Phone Settings menu appears in the display.  
Clock Set  
Use the Clock Set option to set the current time and date.  
Note: In digital service mode, the Clock Set feature is disabled. The network adjusts time and date  
automatically.  
1. From the Settings menu, press  
(for Phone Settings), and  
for Clock Set. The following options appear in the display:  
Set Time  
Set Date  
2. Use the Up and Down navigation to highlight Set Time, then press the  
OK key. The Set Time screen appears in the display.  
3. Enter the current time using your keypad:  
The hour and minute must be entered using two digits each. You must enter the  
hour in 12-hour format.  
Use the Left and Right navigation keys to select am or pm.  
4. Press OK to save the time. The following options appear in the display:  
Set Time  
Set Date  
5. Use the Up and Down navigation to highlight Set Date, then press the  
OK key. The Set Date screen appears in the display.  
6. Enter the current date using your keypad:  
The month and day must be entered using two digits each.  
The year must be entered with all four digits.  
7. Press OK to save the date.  
137  
Phone Settings  
Quick Search  
Quick Search is an easy way to locate contacts in your Address Book and Menu  
items.  
1. From the Settings menu, press  
(for Phone Settings), and  
for Quick Search. The following options appear in the display:  
On  
Off  
2. Use the Up and Down navigation keys to highlight the desired option, then  
press OK .  
Searching for a Contact  
1. In standby mode, press the first few numeric keys that correspond to the  
letters of the contact’s name.  
For example, to search for “Sally” you would enter  
S
A
L
L
Y
2. Press the Up navigation key. The contact name is highlighted.  
3. Press the key to call the contact.  
Searching for a Menu Item  
1. In standby mode, press the first few numeric keys that correspond to the  
letters of the Menu item name.  
For example, to search for “Inbox” you would enter  
I
N
B
O
X
2. Press the Down navigation key. The menu item is highlighted.  
OK  
3. Press the  
key to access the content of the menu item.  
Settings  
138  
Auto Key Lock  
Auto Key Lock lets you enable/disable your phone’s keypad lock. With Auto Key  
Lock set to On and your phone in standby mode, your phone automatically locks the  
phone keypad (but not the QWERTY keypad) and the side keys (Volume and Camera)  
when the backlights go out due to Backlight time expiring. Locking the phone  
keypad prevents accidental call dialing, launching of the camera, and activation of  
other functions.  
1. From the Settings menu, press  
(for Phone Settings), and  
for Auto Key Lock. The following options appear in the display:  
On — Phone keypad and side keys lock automatically when the display and  
keypad backlights go out.  
Off — Phone keypad and side keys remains active.  
2. Use the Up and Down navigation keys to highlight the desired option, then  
press OK .  
Memory Info  
Memory Info shows the amount of phone memory that is available and used, and  
details the distribution of the used memory.  
1. From the Settings menu, press  
for Memory Info. The following  
options appear in the display:  
Memory Usage — Shows Total phone memory, total memory Available, and  
memory quantities used to store Photos, Ringtones, Sounds, and Applications.  
My Images — Lists the photos stored in the My Images folder. Lets you make  
used memory available by erasing unwanted photos.  
My Ringtones — Lists the downloaded ringtones stored in the My Ringtones  
folder. Lets you make used memory available by erasing unwanted ringtones.  
My Sounds — Lists the recorded sounds stored in the My Sounds folder. Lets  
you make used memory available by erasing unwanted recorded sounds.  
2. Use the Up and Down navigation keys to highlight the desired option, then  
press OK .  
3. To delete selected photos, downloaded ringtones, or recorded sounds,  
press the Erase (right) soft key (  
). The selected Erase screen appears  
in the display. Do the following:  
Mark individual files by highlighting each file, then pressing the MARK key  
OK ); or mark all files by pressing the Mark All (right) soft key (  
).  
Press the Done (left) soft key ( ).  
(
You are prompted to confirm the erasure(s).  
To erase the selected file(s), press the Yes (left) soft key (  
).  
139  
   
Phone Info  
To keep the selected file(s), press the No (right) soft key (  
Phone Info  
).  
Phone Info lets you identify the hardware and software versions of your phone and  
to identify the phone number assigned to your phone.  
Phone Number  
This option causes the Phone Number screen to appear in the display and show the  
ten-digit number assigned to your phone by your Wireless Carrier.  
1. From the Settings menu, press  
(for Phone Info), and  
for  
Phone Number. The phone number assigned by your Wireless Carrier  
appears in the display.  
2. Press OK to return to the Phone Info menu.  
Icon Glossary  
This option causes the ICON GLOSSARY list to appear in the display and show the  
icons that can appear in the display and the names of the icons.  
1. From the Settings menu, press  
(for Phone Info), and  
for  
Icon Glossary. A list of the icons that can appear on the top line of the  
display shows in the display.  
2. Press OK to return to the Phone Info menu.  
Version  
You can view the PRL (Preferred Roaming List), ERI (Extended Roaming Indicator),  
software version, and hardware version on your phone. This feature is helpful if you  
need to contact Customer Service.  
1. From the Settings menu, press  
(for Phone Info), and  
for  
Version.  
Hardware and software information for your phone appears in the display.  
2. Press the OK key to return to the Phone Info menu.  
Settings  
140  
           
Section 14: Health and Safety Information  
Topics Covered  
This section outlines the safety precautions associated with using your phone. These  
safety precautions should be followed to safely use your phone.  
Health and Safety Information  
Exposure to Radio Frequency (RF) Signals  
Certification Information (SAR)  
Your wireless phone is a radio transmitter and receiver. It is designed and  
manufactured not to exceed the exposure limits for radio frequency (RF) energy set  
by the Federal Communications Commission (FCC) of the U.S. government.  
141  
       
Health and Safety Information  
These FCC exposure limits are derived from the recommendations of two expert  
organizations, the National Counsel on Radiation Protection and Measurement  
(NCRP) and the Institute of Electrical and Electronics Engineers (IEEE). In both cases,  
the recommendations were developed by scientific and engineering experts drawn  
from industry, government, and academia after extensive reviews of the scientific  
literature related to the biological effects of RF energy.  
The exposure limit set by the FCC for wireless mobile phones employs a unit of  
measurement known as the Specific Absorption Rate (SAR). The SAR is a measure of  
the rate of absorption of RF energy by the human body expressed in units of watts  
per kilogram (W/kg). The FCC requires wireless phones to comply with a safety limit  
of 1.6 watts per kilogram (1.6 W/kg). The FCC exposure limit incorporates a  
substantial margin of safety to give additional protection to the public and to account  
for any variations in measurements.  
SAR tests are conducted using standard operating positions accepted by the FCC  
with the phone transmitting at its highest certified power level in all tested frequency  
bands. Although the SAR is determined at the highest certified power level, the  
actual SAR level of the phone while operating can be well below the maximum value.  
This is because the phone is designed to operate at multiple power levels so as to  
use only the power required to reach the network. In general, the closer you are to a  
wireless base station antenna, the lower the power output.  
Before a new model phone is available for sale to the public, it must be tested and  
certified to the FCC that it does not exceed the exposure limit established by the  
FCC. Tests for each model phone are performed in positions and locations (e.g. at  
the ear and worn on the body) as required by the FCC. For body worn operation, this  
phone has been tested and meets FCC RF exposure guidelines when used with an  
accessory that contains no metal and that positions the handset a minimum of  
1.5 cm from the body. Use of other accessories may not ensure compliance with FCC  
RF exposure guidelines.  
The FCC has granted an Equipment Authorization for this mobile phone with all  
reported SAR levels evaluated as in compliance with the FCC RF exposure  
guidelines. The maximum SAR values for this model phone as reported to the FCC  
are:  
Head: 1.04 W/Kg.  
Body-worn: 1.4 W/Kg.  
Health and Safety Information  
142  
SAR information on this and other model phones can be viewed on-line at  
http://www.fcc.gov/oet/ea. To find information that pertains to a particular model  
phone, this site uses the phone FCC ID number which is usually printed somewhere  
on the case of the phone.  
Sometimes it may be necessary to remove the battery pack to find the number. Once  
you have the FCC ID number for a particular phone, follow the instructions on the  
website and it should provide values for typical or maximum SAR for a particular  
phone. Additional product specific SAR information can also be obtained at  
Samsung Mobile Products and Recycling  
Samsung cares for the environment and encourages its customers to recycle  
Samsung mobile phones and genuine Samsung accessories.  
UL Certified Travel Adapter  
The Travel Adapter for this phone has met applicable UL safety requirements. Please  
adhere to the following safety instructions per UL guidelines.  
FAILURE TO FOLLOW THE INSTRUCTIONS OUTLINED MAY LEAD TO SERIOUS  
PERSONAL INJURY AND POSSIBLE PROPERTY DAMAGE  
IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS.  
DANGER - TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, CAREFULLY FOLLOW  
THESE INSTRUCTIONS.  
FOR CONNECTION TO A SUPPLY NOT IN NORTH AMERICA, USE AN ATTACHMENT  
PLUG ADAPTOR OF THE PROPER CONFIGURATION FOR THE POWER OUTLET. THIS  
POWER UNIT IS INTENDED TO BE CORRECTLY ORIENTATED IN A VERTICAL OR  
HORIZONTAL OR FLOOR MOUNT POSITION.  
Consumer Information on Wireless Phones  
The U.S. Food and Drug Administration (FDA) has published a series of Questions  
and Answers for consumers relating to radio frequency (RF) exposure from wireless  
phones. The FDA publication includes the following information:  
143  
       
Consumer Information on Wireless Phones  
What kinds of phones are the subject of this update?  
The term wireless phone refers here to hand-held wireless phones with built-in  
antennas, often called "cell," "mobile," or "PCS" phones. These types of wireless  
phones can expose the user to measurable radio frequency energy (RF) because of  
the short distance between the phone and the user's head. These RF exposures are  
limited by Federal Communications Commission safety guidelines that were  
developed with the advice of FDA and other federal health and safety agencies.  
When the phone is located at greater distances from the user, the exposure to RF is  
drastically lower because a person's RF exposure decreases rapidly with increasing  
distance from the source. The so-called "cordless phones," which have a base unit  
connected to the telephone wiring in a house, typically operate at far lower power  
levels, and thus produce RF exposures well within the FCC's compliance limits.  
Do wireless phones pose a health hazard?  
The available scientific evidence does not show that any health problems are  
associated with using wireless phones. There is no proof, however, that wireless  
phones are absolutely safe. Wireless phones emit low levels of radio frequency  
energy (RF) in the microwave range while being used. They also emit very low levels  
of RF when in the stand-by mode. Whereas high levels of RF can produce health  
effects (by heating tissue), exposure to low level RF that does not produce heating  
effects causes no known adverse health effects. Many studies of low level RF  
exposures have not found any biological effects. Some studies have suggested that  
some biological effects may occur, but such findings have not been confirmed by  
additional research. In some cases, other researchers have had difficulty in  
reproducing those studies, or in determining the reasons for inconsistent results.  
What is FDA's role concerning the safety of wireless  
phones?  
Under the law, FDA does not review the safety of radiation-emitting consumer  
products such as wireless phones before they can be sold, as it does with new drugs  
or medical devices. However, the agency has authority to take action if wireless  
phones are shown to emit radio frequency energy (RF) at a level that is hazardous to  
the user. In such a case, FDA could require the manufacturers of wireless phones to  
notify users of the health hazard and to repair, replace or recall the phones so that  
the hazard no longer exists.  
Health and Safety Information  
144  
Although the existing scientific data do not justify FDA regulatory actions, FDA has  
urged the wireless phone industry to take a number of steps, including the following:  
Support needed research into possible biological effects of RF of the type emitted  
by wireless phones;  
Design wireless phones in a way that minimizes any RF exposure to the user that  
is not necessary for device function; and  
Cooperate in providing users of wireless phones with the best possible information  
on possible effects of wireless phone use on human health.  
FDA belongs to an interagency working group of the federal agencies that have  
responsibility for different aspects of RF safety to ensure coordinated efforts at the  
federal level. The following agencies belong to this working group:  
National Institute for Occupational Safety and Health  
Environmental Protection Agency  
Federal Communications Commission  
Occupational Safety and Health Administration  
National Telecommunications and Information Administration  
The National Institutes of Health participates in some interagency working group  
activities, as well.  
FDA shares regulatory responsibilities for wireless phones with the Federal  
Communications Commission (FCC). All phones that are sold in the United States  
must comply with FCC safety guidelines that limit RF exposure. FCC relies on FDA  
and other health agencies for safety questions about wireless phones.  
FCC also regulates the base stations that the wireless phone networks rely upon.  
While these base stations operate at higher power than do the wireless phones  
themselves, the RF exposures that people get from these base stations are typically  
thousands of times lower than those they can get from wireless phones. Base  
stations are thus not the primary subject of the safety questions discussed in this  
document.  
145  
Consumer Information on Wireless Phones  
What are the results of the research done already?  
The research done thus far has produced conflicting results, and many studies have  
suffered from flaws in their research methods. Animal experiments investigating the  
effects of radio frequency energy (RF) exposures characteristic of wireless phones  
have yielded conflicting results that often cannot be repeated in other laboratories. A  
few animal studies, however, have suggested that low levels of RF could accelerate  
the development of cancer in laboratory animals. However, many of the studies that  
showed increased tumor development used animals that had been genetically  
engineered or treated with cancer-causing chemicals so as to be pre-disposed to  
develop cancer in absence of RF exposure. Other studies exposed the animals to RF  
for up to 22 hours per day. These conditions are not similar to the conditions under  
which people use wireless phones, so we don't know with certainty what the results  
of such studies mean for human health.  
Three large epidemiology studies have been published since December 2000.  
Between them, the studies investigated any possible association between the use of  
wireless phones and primary brain cancer, glioma, meningioma, or acoustic  
neuroma, tumors of the brain or salivary gland, leukemia, or other cancers. None of  
the studies demonstrated the existence of any harmful health effects from wireless  
phones RF exposures. However, none of the studies can answer questions about  
long-term exposures, since the average period of phone use in these studies was  
around three years.  
What research is needed to decide whether RF exposure  
from wireless phones poses a health risk?  
A combination of laboratory studies and epidemiological studies of people actually  
using wireless phones would provide some of the data that are needed. Lifetime  
animal exposure studies could be completed in a few years. However, very large  
numbers of animals would be needed to provide reliable proof of a cancer promoting  
effect if one exists. Epidemiological studies can provide data that is directly  
applicable to human populations, but ten or more years' follow-up may be needed to  
provide answers about some health effects, such as cancer. This is because the  
interval between the time of exposure to a cancer-causing agent and the time  
tumors develop - if they do - may be many, many years. The interpretation of  
epidemiological studies is hampered by difficulties in measuring actual RF exposure  
during day-to-day use of wireless phones. Many factors affect this measurement,  
such as the angle at which the phone is held, or which model of phone is used.  
Health and Safety Information  
146  
What is FDA doing to find out more about the possible  
health effects of wireless phone RF?  
FDA is working with the U.S. National Toxicology Program and with groups of  
investigators around the world to ensure that high priority animal studies are  
conducted to address important questions about the effects of exposure to radio  
frequency energy (RF).  
FDA has been a leading participant in the World Health Organization international  
Electromagnetic Fields (EMF) Project since its inception in 1996. An influential result  
of this work has been the development of a detailed agenda of research needs that  
has driven the establishment of new research programs around the world. The  
Project has also helped develop a series of public information documents on EMF  
issues.  
FDA and Cellular Telecommunications & Internet Association (CTIA) have a formal  
Cooperative Research and Development Agreement (CRADA) to do research on  
wireless phone safety. FDA provides the scientific oversight, obtaining input from  
experts in government, industry, and academic organizations. CTIA-funded research  
is conducted through contracts to independent investigators. The initial research will  
include both laboratory studies and studies of wireless phone users. The CRADA will  
also include a broad assessment of additional research needs in the context of the  
latest research developments around the world.  
What steps can I take to reduce my exposure to radio  
frequency energy from my wireless phone?  
If there is a risk from these products - and at this point we do not know that there is  
- it is probably very small. But if you are concerned about avoiding even potential  
risks, you can take a few simple steps to minimize your exposure to radio frequency  
energy (RF). Since time is a key factor in how much exposure a person receives,  
reducing the amount of time spent using a wireless phone will reduce RF exposure.  
If you must conduct extended conversations by wireless phone every day, you  
could place more distance between your body and the source of the RF, since the  
exposure level drops off dramatically with distance. For example, you could use a  
headset and carry the wireless phone away from your body or use a wireless  
phone connected to a remote antenna.  
Again, the scientific data do not demonstrate that wireless phones are harmful. But if  
you are concerned about the RF exposure from these products, you can use  
measures like those described above to reduce your RF exposure from wireless  
phone use.  
147  
Consumer Information on Wireless Phones  
What about children using wireless phones?  
The scientific evidence does not show a danger to users of wireless phones,  
including children and teenagers. If you want to take steps to lower exposure to  
radio frequency energy (RF), the measures described above would apply to children  
and teenagers using wireless phones. Reducing the time of wireless phone use and  
increasing the distance between the user and the RF source will reduce RF  
exposure.  
Some groups sponsored by other national governments have advised that children  
be discouraged from using wireless phones at all. For example, the government in  
the United Kingdom distributed leaflets containing such a recommendation in  
December 2000. They noted that no evidence exists that using a wireless phone  
causes brain tumors or other ill effects. Their recommendation to limit wireless  
phone use by children was strictly precautionary; it was not based on scientific  
evidence that any health hazard exists.  
Do hands-free kits for wireless phones reduce  
risks from exposure to RF emissions?  
Since there are no known risks from exposure to RF emissions from wireless  
phones, there is no reason to believe that hands-free kits reduce risks. Hands-free  
kits can be used with wireless phones for convenience and comfort. These systems  
reduce the absorption of RF energy in the head because the phone, which is the  
source of the RF emissions, will not be placed against the head. On the other hand, if  
the phone is mounted against the waist or other part of the body during use, then  
that part of the body will absorb more RF energy. Wireless phones marketed in the  
U.S. are required to meet safety requirements regardless of whether they are used  
against the head or against the body. Either configuration should result in  
compliance with the safety limit.  
Do wireless phone accessories that claim to shield  
the head from RF radiation work?  
Since there are no known risks from exposure to RF emissions from wireless  
phones, there is no reason to believe that accessories that claim to shield the head  
from those emissions reduce risks. Some products that claim to shield the user from  
RF absorption use special phone cases, while others involve nothing more than a  
metallic accessory attached to the phone. Studies have shown that these products  
generally do not work as advertised. Unlike "hand-free" kits, these so-called  
"shields" may interfere with proper operation of the phone. The phone may be  
forced to boost its power to compensate, leading to an increase in RF absorption.  
Health and Safety Information  
148  
In February 2002, the Federal trade Commission (FTC) charged two companies that  
sold devices that claimed to protect wireless phone users from radiation with  
making false and unsubstantiated claims. According to FTC, these defendants  
lacked a reasonable basis to substantiate their claim.  
What about wireless phone interference with  
medical equipment?  
Radio frequency energy (RF) from wireless phones can interact with some electronic  
devices. For this reason, FDA helped develop a detailed test method to measure  
electromagnetic interference (EMI) of implanted cardiac pacemakers and  
defibrillators from wireless telephones. This test method is now part of a standard  
sponsored by the Association for the Advancement of Medical instrumentation  
(AAMI). The final draft, a joint effort by FDA, medical device manufacturers, and  
many other groups, was completed in late 2000. This standard will allow  
manufacturers to ensure that cardiac pacemakers and defibrillators are safe from  
wireless phone EMI. FDA has tested wireless phones and helped develop a voluntary  
standard sponsored by the Institute of Electrical and Electronic Engineers (IEEE). This  
standard specifies test methods and performance requirements for hearing aids and  
wireless phones so that no interference occurs when a person uses a compatible  
phone and a compatible hearing aid at the same time. This standard was approved  
by the IEEE in 2000.  
FDA continues to monitor the use of wireless phones for possible interactions with  
other medical devices. Should harmful interference be found to occur, FDA will  
conduct testing to assess the interference and work to resolve the problem.  
Additional information on the safety of RF exposures from various sources can be  
obtained from the following organizations (Updated 12/1/2006):  
FCC RF Safety Program:  
Environmental Protection Agency (EPA):  
Occupational Safety and Health Administration's (OSHA):  
National Institute for Occupational Safety and Health (NIOSH):  
World Health Organization (WHO):  
149  
Road Safety  
International Commission on Non-Ionizing Radiation Protection:  
National Radiation Protection Board (UK):  
US Food and Drug Administration  
Road Safety  
Your wireless phone gives you the powerful ability to communicate by voice, almost  
anywhere, anytime. But an important responsibility accompanies the benefits of  
wireless phones, one that every user must uphold.  
When driving a car, driving is your first responsibility. When using your wireless  
phone behind the wheel of a car, practice good common sense and remember the  
following tips:  
1. Get to know your wireless phone and its features, such as speed dial and  
redial. If available, these features help you to place your call without taking  
your attention off the road.  
2. When available, use a hands-free device. If possible, add an additional  
layer of convenience and safety to your wireless phone with one of the  
many hands free accessories available today.  
3. Position your wireless phone within easy reach. Be able to access your  
wireless phone without removing your eyes from the road. If you get an  
incoming call at an inconvenient time, let your voice mail answer it for you.  
4. Let the person you are speaking with know you are driving; if necessary,  
suspend the call in heavy traffic or hazardous weather conditions. Rain,  
sleet, snow, ice and even heavy traffic can be hazardous.  
5. Do not take notes or look up phone numbers while driving. Jotting down a  
"to do" list or flipping through your address book takes attention away  
from your primary responsibility, driving safely.  
6. Dial sensibly and assess the traffic; if possible, place calls when you are  
not moving or before pulling into traffic. Try to plan calls when your car will  
be stationary. If you need to make a call while moving, dial only a few  
numbers, check the road and your mirrors, then continue.  
Health and Safety Information  
150  
 
7. Do not engage in stressful or emotional conversations that may be  
distracting. Make people you are talking with aware you are driving and  
suspend conversations that have the potential to divert your attention from  
the road.  
8. Use your wireless phone to call for help. Dial 9-1-1 or other local  
emergency number in the case of fire, traffic accident or medical  
emergencies.  
9. Use your wireless phone to help others in emergencies. If you see an auto  
accident, crime in progress or other serious emergency where lives are in  
danger, call 9-1-1 or other local emergency number, as you would want  
others to do for you.  
10. Call roadside assistance or a special non-emergency wireless assistance  
number when necessary. If you see a broken-down vehicle posing no  
serious hazard, a broken traffic signal, a minor traffic accident where no  
one appears injured, or a vehicle you know to be stolen, call roadside  
assistance or other special non-emergency number.  
"The wireless industry reminds you to use your phone safely when driving."  
For more information, please call 1-888-901-SAFE, or visit our web-site  
Important!: If you are using a handset other than a standard numeric keypad, please call 1-888-901-7233.  
Provided by the Cellular Telecommunications & Internet Association.  
Responsible Listening  
Caution!: Avoid potential hearing loss.  
Damage to hearing occurs when a person is exposed to loud sounds over time. The  
risk of hearing loss increases as sound is played louder and for longer durations.  
Prolonged exposure to loud sounds (including music) is the most common cause of  
preventable hearing loss. Some scientific research suggests that using portable  
audio devices, such as portable music players and cellular telephones, at high  
volume settings for long durations may lead to permanent noise-induced hearing  
loss. This includes the use of headphones (including headsets, earbuds, and  
Bluetooth or other wireless devices). Exposure to very loud sound has also been  
associated in some studies with tinnitus (a ringing in the ear), hypersensitivity to  
sound and distorted hearing.  
151  
   
Responsible Listening  
Individual susceptibility to noise-induced hearing loss and potential hearing problem  
varies. Additionally, the amount of sound produced by a portable audio device varies  
depending on the nature of the sound, the device settings, and the headphones that  
are used. As a result, there is no single volume setting that is appropriate for  
everyone or for every combination of sound, settings and equipment.  
You should follow some commonsense recommendations when using any portable  
audio device:  
Set the volume in a quiet environment and select the lowest volume at which you  
can hear adequately.  
When using headphones, turn the volume down if you cannot hear the people  
speaking near you or if the person sitting next to you can hear what you are  
listening to.  
Do not turn the volume up to block out noisy surroundings. If you choose to listen  
to your portable device in a noisy environment, you noise-cancelling headphones  
to block out background environmental noise. By blocking background  
environment noise, noise cancelling headphones should allow you to hear the  
music at lower volumes than when using earbuds.  
Limit the amount of time you listen. As the volume increases, less time is required  
before you hearing could be affected.  
Avoid using headphones after exposure to extremely loud noises, such as rock  
concerts, that might cause temporary hearing loss. Temporary hearing loss might  
cause unsafe volumes to sound normal.  
Do not listen at any volume that causes you discomfort. If you experience ringing  
in your ears, hear muffled speech or experience any temporary hearing difficulty  
after listening to your portable audio device, discontinue use and consult your  
doctor.  
You can obtain additional information on this subject from the following sources:  
American Academy of Audiology  
11730 Plaza American Drive, Suite 300  
Reston, VA 20190  
Voice: (800) 222-2336  
Internet: http://www.audiology.org  
Health and Safety Information  
152  
National Institute on Deafness and Other Communication Disorders  
National Institutes of Health  
31 Center Drive, MSC 2320  
Bethesda, MD 20892-2320  
Voice: (301) 496-7243  
National Institute for Occupational Safety and Health  
Hubert H. Humphrey Bldg.  
200 Independence Ave., SW  
Washington, DC 20201  
Voice: 1-800-35-NIOSH (1-800-356-4647)  
Operating Environment  
Remember to follow any special regulations in force in any area and always switch  
your phone off whenever it is forbidden to use it, or when it may cause interference  
or danger. When connecting the phone or any accessory to another device, read its  
user's guide for detailed safety instructions. Do not connect incompatible products.  
As with other mobile radio transmitting equipment, users are advised that for the  
satisfactory operation of the equipment and for the safety of personnel, it is  
recommended that the equipment should only be used in the normal operating  
position (held to your ear with the antenna pointing over your shoulder if you are  
using an external antenna).  
Using Your Phone Near Other Electronic Devices  
Most modern electronic equipment is shielded from radio frequency (RF) signals.  
However, certain electronic equipment may not be shielded against the RF signals  
from your wireless phone. Consult the manufacturer to discuss alternatives.  
153  
     
Using Your Phone Near Other Electronic Devices  
Implantable Medical Devices  
A minimum separation of six (6) inches should be maintained between a handheld  
wireless phone and an implantable medical device, such as a pacemaker or  
implantable cardioverter defibrillator, to avoid potential interference with the device.  
Persons who have such devices:  
Should ALWAYS keep the phone more than six (6) inches from their implantable  
medical device when the phone is turned ON;  
Should not carry the phone in a breast pocket;  
Should use the ear opposite the implantable medical device to minimize the  
potential for interference;  
Should turn the phone OFF immediately if there is any reason to suspect that  
interference is taking place.  
Should read and follow the directions from the manufacturer of your implantable  
medical device. if you have any questions about using your wireless phone with  
such a device, consult your health care provider.  
For more information see, http://www.fcc.gov/oet/rfsafety/rf-faqs.html  
Hearing Aid Compatibility with Mobile Phones  
When some mobile phones are used near some hearing devices (hearing aids and  
cochlear implants), users may detect a buzzing, humming, or whining noise. Some  
hearing devices are more immune than others to this interference noise, and phones  
also vary in the amount of interference they generate.  
The wireless telephone industry has developed ratings for some of their mobile  
phones, to assist hearing device users in finding phones that may be compatible  
with their hearing devices. Not all phones have been rated. Phones that are rated  
have the rating on their box or a label on the box.  
The ratings are not guarantees. Results will vary depending on the user’s hearing  
device and hearing loss. If your hearing device happens to be vulnerable to  
interference, you may not be able to use a rated phone successfully. Trying out the  
phone with your hearing device is the best way to evaluate it for your personal  
needs.  
M-Ratings: Phones rated M3 or M4 meet FCC requirements and are likely to  
generate less interference to hearing devices than phones that are not labeled. M4 is  
the better/higher of the two ratings.  
Health and Safety Information  
154  
T-Ratings: Phones rated T3 or T4 meet FCC requirements and are likely to be more  
usable with a hearing device’s telecoil (“T Switch” or “Telephone Switch”) than  
unrated phones. T4 is the better/higher of the two ratings. (Note that not all hearing  
devices have telecoils in them.)  
Hearing devices may also be measured for immunity to this type of interference.  
Your hearing device manufacturer or hearing health professional may help you find  
results for your hearing device. The more immune your hearing aid is, the less likely  
you are to experience interference noise from mobile phones.  
Other Medical Devices  
If you use any other personal medical devices, consult the manufacturer of your  
device to determine if it is adequately shielded from external RF energy. Your  
physician may be able to assist you in obtaining this information. Switch your phone  
off in health care facilities when any regulations posted in these areas instruct you to  
do so. Hospitals or health care facilities may be using equipment that could be  
sensitive to external RF energy.  
Vehicles  
RF signals may affect improperly installed or inadequately shielded electronic  
systems in motor vehicles. Check with the manufacturer or its representative  
regarding your vehicle. You should also consult the manufacturer of any equipment  
that has been added to your vehicle.  
Posted Facilities  
Switch your phone off in any facility where posted notices require you to do so.  
Potentially Explosive Environments  
Switch your phone off when in any area with a potentially explosive atmosphere and  
obey all signs and instructions. Sparks in such areas could cause an explosion or fire  
resulting in bodily injury or even death.  
Users are advised to switch the phone off while at a refueling point (service station).  
Users are reminded of the need to observe restrictions on the use of radio equipment  
in fuel depots (fuel storage and distribution areas), chemical plants or where blasting  
operations are in progress.  
155  
 
Emergency Calls  
Areas with a potentially explosive atmosphere are often but not always clearly  
marked. They include below deck on boats, chemical transfer or storage facilities,  
vehicles using liquefied petroleum gas (such as propane or butane), areas where the  
air contains chemicals or particles, such as grain, dust or metal powders, and any  
other area where you would normally be advised to turn off your vehicle engine.  
Emergency Calls  
This phone, like any wireless phone, operates using radio signals, wireless and  
landline networks as well as user-programmed functions, which cannot guarantee  
connection in all conditions. Therefore, you should never rely solely on any wireless  
phone for essential communications (medical emergencies, for example).  
Remember, to make or receive any calls the phone must be switched on and in a  
service area with adequate signal strength. Emergency calls may not be possible on  
all wireless phone networks or when certain network services and/or phone features  
are in use. Check with local service providers.  
To make an emergency call:  
1. If the phone is not on, switch it on.  
2. Key in the emergency number for your present location (for example, 911  
or other official emergency number). Emergency numbers vary by location.  
3. Press the  
key.  
If certain features are in use (call barring, for example), you may first need to  
deactivate those features before you can make an emergency call. Consult this  
document and your local cellular service provider.  
When making an emergency call, remember to give all the necessary information as  
accurately as possible. Remember that your phone may be the only means of  
communication at the scene of an accident; do not cut off the call until given  
permission to do so.  
Restricting Children's access to your Phone  
Your phone is not a toy. Children should not be allowed to play with it because they  
could hurt themselves and others, damage the phone or make calls that increase  
your phone bill.  
Health and Safety Information  
156  
 
FCC Notice and Cautions  
FCC Notice  
The phone may cause TV or radio interference if used in close proximity to receiving  
equipment. The FCC can require you to stop using the phone if such interference  
cannot be eliminated.  
Vehicles using liquefied petroleum gas (such as propane or butane) must comply  
with the National Fire Protection Standard (NFPA-58). For a copy of this standard,  
contact the National Fire Protection Association, One Batterymarch Park, Quincy, MA  
02269, Attn: Publication Sales Division.  
Cautions  
Any changes or modifications to your phone not expressly approved in this  
document could void your warranty for this equipment, and void your authority to  
operate this equipment. Only use approved batteries, antennas and chargers. The  
use of any unauthorized accessories may be dangerous and void the phone warranty  
if said accessories cause damage or a defect to the phone.  
Although your phone is quite sturdy, it is a complex piece of equipment and can be  
broken. Avoid dropping, hitting, bending or sitting on it.  
Other Important Safety Information  
Only qualified personnel should service the phone or install the phone in a vehicle.  
Faulty installation or service may be dangerous and may invalidate any warranty  
applicable to the device.  
Check regularly that all wireless phone equipment in your vehicle is mounted and  
operating properly.  
Do not store or carry flammable liquids, gases or explosive materials in the same  
compartment as the phone, its parts or accessories.  
For vehicles equipped with an air bag, remember that an air bag inflates with great  
force. Do not place objects, including both installed or portable wireless equipment  
in the area over the air bag or in the air bag deployment area. If wireless  
equipment is improperly installed and the air bag inflates, serious injury could  
result.  
Switch your phone off before boarding an aircraft. The use of wireless phone in  
aircraft is illegal and may be dangerous to the aircraft's operation.  
Failure to observe these instructions may lead to the suspension or denial of  
telephone services to the offender, or legal action, or both.  
157  
   
Product Performance  
Product Performance  
Getting the Most Out of Your Signal Reception  
The quality of each call you make or receive depends on the signal strength in your  
area. Your phone informs you of the current signal strength by displaying a number  
of bars next to the signal strength icon. The more bars displayed, the stronger the  
signal.  
If you're inside a building, being near a window may give you better reception.  
Understanding the Power Save Feature  
If your phone is unable to find a signal after searching, a Power Save feature is  
automatically activated. If your phone is active, it periodically rechecks service  
availability or you can check it yourself by pressing any key.  
Anytime the Power Save feature is activated, a message displays on the screen.  
When a signal is found, your phone returns to standby mode.  
Understanding How Your Phone Operates  
Your phone is basically a radio transmitter and receiver. When it's turned on, it  
receives and transmits radio frequency (RF) signals. When you use your phone, the  
system handling your call controls the power level. This power can range from 0.006  
watts to 0.2 watts in digital mode.  
Maintaining Your Phone's Peak Performance  
For the best care of your phone, only authorized personnel should service your  
phone and accessories. Faulty service may void the warranty.  
There are several simple guidelines to operating your phone properly and  
maintaining safe, satisfactory service.  
If your phone is equipped with an external antenna, hold the phone with the  
antenna raised, fully-extended and over your shoulder.  
Do not hold, bend or twist the phone's antenna, if applicable.  
Do not use the phone if the antenna is damaged.  
If your phone is equipped with an internal antenna, obstructing the internal  
antenna could inhibit call performance.  
Speak directly into the phone's receiver.  
Avoid exposing your phone and accessories to rain or liquid spills. If your phone  
does get wet, immediately turn the power off and remove the battery. If it is  
inoperable, call Customer Care for service.  
Health and Safety Information  
158  
 
Availability of Various Features/Ring Tones  
Many services and features are network dependent and may require additional  
subscription and/or usage charges. Not all features are available for purchase or use  
in all areas. Downloadable Ring Tones may be available at an additional cost. Other  
conditions and restrictions may apply. See your service provider for additional  
information.  
Battery Standby and Talk Time  
Standby and talk times will vary depending on phone usage patterns and conditions.  
Battery power consumption depends on factors such as network configuration,  
signal strength, operating temperature, features selected, frequency of calls, and  
voice, data, and other application usage patterns.  
Battery Precautions  
Avoid dropping the cell phone. Dropping it, especially on a hard surface, can  
potentially cause damage to the phone and battery. If you suspect damage to the  
phone or battery, take it to a service center for inspection.  
Never use any charger or battery that is damaged in any way.  
Do not modify or remanufacture the battery as this could result in serious safety  
hazards.  
If you use the phone near the network's base station, it uses less power; talk and  
standby time are greatly affected by the signal strength on the cellular network  
and the parameters set by the network operator.  
Follow battery usage, storage and charging guidelines found in the user’s guide.  
Battery charging time depends on the remaining battery charge and the type of  
battery and charger used. The battery can be charged and discharged hundreds of  
times, but it will gradually wear out. When the operation time (talk time and  
standby time) is noticeably shorter than normal, it is time to buy a new battery.  
If left unused, a fully charged battery will discharge itself over time.  
Use only Samsung-approved batteries and recharge your battery only with  
Samsung-approved chargers. When a charger is not in use, disconnect it from the  
power source. Do not leave the battery connected to a charger for more than a  
week, since overcharging may shorten its life.  
Do not use incompatible cell phone batteries and chargers. Some Web sites and  
second-hand dealers, not associated with reputable manufacturers and carriers,  
might be selling incompatible or even counterfeit batteries and chargers.  
Consumers should purchase manufacturer or carrier recommended products and  
159  
     
Battery Precautions  
accessories. If unsure about whether a replacement battery or charger is  
compatible, contact the manufacturer of the battery or charger.  
Misuse or use of incompatible phones, batteries, and charging devices could  
result in damage to the equipment and a possible risk of fire, explosion, leakage,  
or other serious hazard.  
Extreme temperatures will affect the charging capacity of your battery: it may  
require cooling or warming first.  
Do not leave the battery in hot or cold places, such as in a car in summer or winter  
conditions, as you will reduce the capacity and lifetime of the battery. Always try to  
keep the battery at room temperature. A phone with a hot or cold battery may  
temporarily not work, even when the battery is fully charged. Li-ion batteries are  
particularly affected by temperatures below 0 °C (32 °F).  
Do not place the phone in areas that may get very hot, such as on or near a  
cooking surface, cooking appliance, iron, or radiator.  
Do not get your phone or battery wet. Even though they will dry and appear to  
operate normally, the circuitry could slowly corrode and pose a safety hazard.  
Do not short-circuit the battery. Accidental short-circuiting can occur when a  
metallic object (coin, clip or pen) causes a direct connection between the + and -  
terminals of the battery (metal strips on the battery), for example when you carry a  
spare battery in a pocket or bag. Short-circuiting the terminals may damage the  
battery or the object causing the short-circuiting.  
Do not permit a battery out of the phone to come in contact with metal objects,  
such as coins, keys or jewelry.  
Do not crush, puncture or put a high degree of pressure on the battery as this can  
cause an internal short-circuit, resulting in overheating.  
Dispose of used batteries in accordance with local regulations. In some areas, the  
disposal of batteries in household or business trash may be prohibited. For safe  
disposal options for Li-Ion batteries, contact your nearest Samsung authorized  
service center. Always recycle. Do not dispose of batteries in a fire.  
Health and Safety Information  
160  
Care and Maintenance  
Your phone is a product of superior design and craftsmanship and should be treated  
with care. The suggestions below will help you fulfill any warranty obligations and  
allow you to enjoy this product for many years.  
Keep the phone and all its parts and accessories out of the reach of small children.  
Keep the phone dry. Precipitation, humidity and liquids contain minerals that will  
corrode electronic circuits.  
Do not use the phone with a wet hand. Doing so may cause an electric shock to  
you or damage to the phone.  
Do not use or store the phone in dusty, dirty areas, as its moving parts may be  
damaged.  
Do not store the phone in hot areas. High temperatures can shorten the life of  
electronic devices, damage batteries, and warp or melt certain plastics.  
Do not store the phone in cold areas. When the phone warms up to its normal  
operating temperature, moisture can form inside the phone, which may damage  
the phone's electronic circuit boards.  
Do not drop, knock or shake the phone. Rough handling can break internal circuit  
boards.  
Do not use harsh chemicals, cleaning solvents or strong detergents to clean the  
phone. Wipe it with a soft cloth slightly dampened in a mild soap-and-water  
solution.  
Do not paint the phone. Paint can clog the device's moving parts and prevent  
proper operation.  
Do not put the phone in or on heating devices, such as a microwave oven, a stove  
or a radiator. The phone may explode when overheated.  
If your phone is equipped with an external antenna, use only the supplied or an  
approved replacement antenna. Unauthorized antennas or modified accessories  
may damage the phone and violate regulations governing radio devices.  
If the phone, battery, charger or any accessory is not working properly, take it to  
your nearest qualified service facility. The personnel there will assist you, and if  
necessary, arrange for service.  
161  
 
Standard Limited Warranty  
Section 15: Warranty Information  
Topics Covered  
Standard Limited Warranty  
What is Covered and For How Long? SAMSUNG  
TELECOMMUNICATIONS AMERICA, LLC ("SAMSUNG") warrants to the original  
purchaser ("Purchaser") that SAMSUNG's Phones and accessories ("Products") are  
free from defects in material and workmanship under normal use and service for the  
period commencing upon the date of purchase and continuing for the following  
specified period of time after that date:  
Phone  
1 Year  
1 Year  
Batteries  
Leather Case/ Pouch  
Holster  
90 Days  
90 Days  
1 Year  
Other Phone Accessories  
What is Not Covered? This Limited Warranty is conditioned upon proper use of  
Product by Purchaser. This Limited Warranty does not cover: (a) defects or damage  
resulting from accident, misuse, abuse, neglect, unusual physical, electrical or  
electromechanical stress, or modification of any part of Product, including antenna,  
or cosmetic damage; (b) equipment that has the serial number removed or made  
illegible; (c) any plastic surfaces or other externally exposed parts that are scratched  
or damaged due to normal use; (d) malfunctions resulting from the use of Product in  
conjunction with accessories, products, or ancillary/peripheral equipment not  
furnished or approved by SAMSUNG; (e) defects or damage from improper testing,  
operation, maintenance, installation, or adjustment; (f) installation, maintenance,  
and service of Product, or (g) Product used or purchased outside the United States or  
Canada.  
Warranty Information  
162  
       
This Limited Warranty covers batteries only if battery capacity falls below 80% of  
rated capacity or the battery leaks, and this Limited Warranty does not cover any  
battery if (i) the battery has been charged by a battery charger not specified or  
approved by SAMSUNG for charging the battery, (ii) any of the seals on the battery  
are broken or show evidence of tampering, or (iii) the battery has been used in  
equipment other than the SAMSUNG phone for which it is specified.  
What are SAMSUNG's Obligations? During the applicable warranty period,  
SAMSUNG will repair or replace, at SAMSUNG's sole option, without charge to  
Purchaser, any defective component part of Product. To obtain service under this  
Limited Warranty, Purchaser must return Product to an authorized phone service  
facility in an adequate container for shipping, accompanied by Purchaser's sales  
receipt or comparable substitute proof of sale showing the date of purchase, the  
serial number of Product and the sellers' name and address. To obtain assistance on  
where to deliver the Product, call Samsung Customer Care at 1-888-987-4357.  
Upon receipt, SAMSUNG will promptly repair or replace the defective Product.  
SAMSUNG may, at SAMSUNG's sole option, use rebuilt, reconditioned, or new parts  
or components when repairing any Product or replace Product with a rebuilt,  
reconditioned or new Product. Repaired/replaced leather cases, pouches and  
holsters will be warranted for a period of ninety (90) days. All other repaired/replaced  
Product will be warranted for a period equal to the remainder of the original Limited  
Warranty on the original Product or for 90 days, whichever is longer. All replaced  
parts, components, boards and equipment shall become the property of SAMSUNG.  
If SAMSUNG determines that any Product is not covered by this Limited Warranty,  
Purchaser must pay all parts, shipping, and labor charges for the repair or return of  
such Product.  
WHAT ARE THE LIMITS ON SAMSUNG'S WARRANTY/LIABILITY? EXCEPT AS SET  
FORTH IN THE EXPRESS WARRANTY CONTAINED HEREIN, PURCHASER TAKES THE  
PRODUCT "AS IS," AND SAMSUNG MAKES NO WARRANTY OR REPRESENTATION  
AND THERE ARE NO CONDITIONS, EXPRESS OR IMPLIED, STATUTORY OR  
OTHERWISE, OF ANY KIND WHATSOEVER WITH RESPECT TO THE PRODUCT,  
INCLUDING BUT NOT LIMITED TO:  
THE MERCHANTABILITY OF THE PRODUCT OR ITS FITNESS FOR ANY PARTICULAR  
PURPOSE OR USE;  
WARRANTIES OF TITLE OR NON-INFRINGEMENT;  
DESIGN, CONDITION, QUALITY, OR PERFORMANCE OF THE PRODUCT;  
163  
Standard Limited Warranty  
THE WORKMANSHIP OF THE PRODUCT OR THE COMPONENTS CONTAINED  
THEREIN; OR  
COMPLIANCE OF THE PRODUCT WITH THE REQUIREMENTS OF ANY LAW, RULE,  
SPECIFICATION OR CONTRACT PERTAINING THERETO.  
NOTHING CONTAINED IN THE INSTRUCTION MANUAL SHALL BE CONSTRUED TO  
CREATE AN EXPRESS WARRANTY OF ANY KIND WHATSOEVER WITH RESPECT TO  
THE PRODUCT. ALL IMPLIED WARRANTIES AND CONDITIONS THAT MAY ARISE BY  
OPERATION OF LAW, INCLUDING IF APPLICABLE THE IMPLIED WARRANTIES OF  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY  
LIMITED TO THE SAME DURATION OF TIME AS THE EXPRESS WRITTEN WARRANTY  
STATED HEREIN. SOME STATES/PROVINCES DO NOT ALLOW LIMITATIONS ON HOW  
LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY  
TO YOU. IN ADDITION, SAMSUNG SHALL NOT BE LIABLE FOR ANY DAMAGES OF ANY  
KIND RESULTING FROM THE PURCHASE, USE, OR MISUSE OF, OR INABILITY TO USE  
THE PRODUCT OR ARISING DIRECTLY OR INDIRECTLY FROM THE USE OR LOSS OF  
USE OF THE PRODUCT OR FROM THE BREACH OF THE EXPRESS WARRANTY,  
INCLUDING INCIDENTAL, SPECIAL, CONSEQUENTIAL OR SIMILAR DAMAGES, OR  
LOSS OF ANTICIPATED PROFITS OR BENEFITS, OR FOR DAMAGES ARISING FROM  
ANY TORT (INCLUDING NEGLIGENCE OR GROSS NEGLIGENCE) OR FAULT COMMITTED  
BY SAMSUNG, ITS AGENTS OR EMPLOYEES, OR FOR ANY BREACH OF CONTRACT OR  
FOR ANY CLAIM BROUGHT AGAINST PURCHASER BY ANY OTHER PARTY. SOME  
STATES/PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL  
OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY  
NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU  
MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE/PROVINCE TO  
PROVINCE. THIS LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN  
THE ORIGINAL PURCHASER OF THIS PRODUCT AND STATES PURCHASER'S  
EXCLUSIVE REMEDY. IF ANY PORTION OF THIS LIMITED WARRANTY IS HELD ILLEGAL  
OR UNENFORCEABLE BY REASON OF ANY LAW, SUCH PARTIAL ILLEGALITY OR  
UNENFORCEABILITY SHALL NOT AFFECT THE ENFORCEABILITY FOR THE  
REMAINDER OF THIS LIMITED WARRANTY WHICH PURCHASER ACKNOWLEDGES IS  
AND WILL ALWAYS BE CONSTRUED TO BE LIMITED BY ITS TERMS OR AS LIMITED AS  
THE LAW PERMITS. THE PARTIES UNDERSTAND THAT THE PURCHASER MAY USE  
THIRD-PARTY SOFTWARE OR EQUIPMENT IN CONJUNCTION WITH THE PRODUCT.  
SAMSUNG MAKES NO WARRANTIES OR REPRESENTATIONS AND THERE ARE NO  
CONDITIONS, EXPRESS OR IMPLIED, STATUTORY OR OTHERWISE, AS TO THE  
QUALITY, CAPABILITIES, OPERATIONS, PERFORMANCE OR SUITABILITY OF ANY  
THIRDPARTY SOFTWARE OR EQUIPMENT, WHETHER SUCH THIRD-PARTY SOFTWARE  
Warranty Information  
164  
OR EQUIPMENT IS INCLUDED WITH THE PRODUCT DISTRIBUTED BY SAMSUNG OR  
OTHERWISE, INCLUDING THE ABILITY TO INTEGRATE ANY SUCH SOFTWARE OR  
EQUIPMENT WITH THE PRODUCT. THE QUALITY, CAPABILITIES, OPERATIONS,  
PERFORMANCE AND SUITABILITY OF ANY SUCH THIRD-PARTY SOFTWARE OR  
EQUIPMENT LIE SOLELY WITH THE PURCHASER AND THE DIRECT VENDOR, OWNER  
OR SUPPLIER OF SUCH THIRD-PARTY SOFTWARE OR EQUIPMENT, AS THE CASE MAY  
BE.  
This Limited Warranty allocates risk of Product failure between Purchaser and  
SAMSUNG, and SAMSUNG's Product pricing reflects this allocation of risk and the  
limitations of liability contained in this Limited Warranty. The agents, employees,  
distributors, and dealers of SAMSUNG are not authorized to make modifications to  
this Limited Warranty, or make additional warranties binding on SAMSUNG.  
Accordingly, additional statements such as dealer advertising or presentation,  
whether oral or written, do not constitute warranties by SAMSUNG and should not be  
relied upon.  
Precautions for Transfer and Disposal  
If data stored on this device is deleted or reformatted using the standard methods,  
the data only appears to be removed on a superficial level, and it may be possible for  
someone to retrieve and reuse the data by means of special software.  
To avoid unintended information leaks and other problems of this sort, it is  
recommended that the device be returned to Samsung’s Customer Care Center for  
an Extended File System (EFS) Clear which will eliminate all user memory and return  
all settings to default settings. Please contact the Samsung Customer Care Center  
for details.  
Important!: Please provide warranty information (proof of purchase) to Samsung’s Customer Care Center  
in order to provide this service at no charge. If the warranty has expired on the device, charges  
may apply.  
Customer Care Center:  
1000 Klein St.  
Plano, TX 75074  
Toll Free Tel: 1.888.987.HELP (4357)  
165  
Standard Limited Warranty  
Samsung Telecommunications America, LLC  
1301 East Lookout Drive  
Richardson, Texas 75082  
Phone: 1-800-SAMSUNG (726-7864)  
Important!: If you are using a handset other than a standard numeric keypad, dial the numbers listed  
in brackets.  
Phone: 1-888-987-HELP (4357)  
©2007 Samsung Telecommunications America. All rights reserved.  
No reproduction in whole or in part allowed without prior written approval.  
Specifications and availability subject to change without notice.  
Warranty Information  
166  
Travel adapter 6  
Brightness, pictures 98  
Buying new apps 68  
Index  
Symbols  
C
@metro  
Calculator 116  
Calendar  
On-line Help 67  
Settings 67  
view an event 109  
Call Answer 128  
Call answer 28  
Call Answer mode 18  
Call block 28  
Call Functions 22  
Answering a Call 26  
Making a Call 22  
Call notification types 27  
Call Settings  
Numerics  
2-sec pause 54  
A
Accessing Your Phone’s Settings 122  
Accessing Your Phone’s Tools 106  
Adding a new Contacts entry  
Dial Method 52  
Adjust  
Key Tone 127  
Auto Answer 129  
Auto Retry 129  
Call Answer 128  
Data Settings 130  
TTY Mode 129  
Voice Privacy 130  
Call timer 33  
Call waiting 28  
Caller ID 28  
ringer setting 20, 27  
Alarm clock  
turn off the alarm 114  
when an alarm sounds 114  
Alerts 128  
Apps  
buying 68  
disabled 68  
expired 68  
Calls  
removing 68  
call timer 33  
restoring 68  
Auto Answer 129  
Auto Retry 129  
data counter 33  
erase logs 31  
incoming 30  
missed 31  
outgoing 30  
store numbers 34  
Calls menu 29  
Camera  
B
Backlight 126  
Banner 125  
Battery 5  
charging 6  
Low battery indicator 7  
removal 5  
Options 99  
Screen 97  
Screen Icons 97  
167  
 
Self Timer 99  
Shortcuts 98  
Taking Pictures 96  
E
Edit contacts name and numbers 53  
Emergency 133  
Camera mode 21  
Camera Screen 97  
Canned Message Text  
Editing and Entering 84  
Change lock 133  
Clear key 15  
Emergency #s in lock mode 134  
Emergency numbers 133  
End key 16  
Entering Text 44  
Entering Numbers 47  
Entering Symbols 48  
Using T9 Mode 46  
Contacts 49  
add pauses 54  
Adding a new Contacts  
entry 52  
edit name and numbers 53  
erase all 135  
Erase All Entry 135  
Erase logs 31  
Erase messages 83  
Exit metroWeb 87  
Expired apps 68  
opening 50  
Save a number after a call 57  
G
Gallery  
Contacts List  
Image 103  
Memory 64  
General message settings 83  
Getting Started 4  
Activating Your Phone 7  
Understanding this User  
Manual 7  
Voicemail 8  
Go back one menu 36  
GPS Setting 122  
Create messages 70  
D
Data Counter 33  
Data Settings 130  
Data, view counters 33  
Delay pictures 99  
Dialing Font 125  
Disabled apps 68  
Display 123  
H
Hardware version, viewing 140  
Health and Safety Information 141  
Display screen icons 17  
Display Settings 124  
Backlight 126  
I
Banner 125  
Dialing Font 125  
Wallpaper 123  
Icon Glossary 140  
Icons  
number type 52, 58, 59  
Ignore calls 29  
Inbox folder 76  
Incoming calls 26  
Draft folder 79  
Draft messages 79  
168  
Incoming calls menu 30  
Input mode 18  
input 18  
lock 18  
silent 20  
standby 19  
L
Language 131  
talk 19  
vibrate 20  
Msg setting sub menu 83  
Multimedia 95  
Left soft key 15  
Lock code, changing 133  
Lock mode 18  
Lock phone 132  
N
M
Navigation key 16  
Navigation key shortcuts 37  
Notes and tips 4  
Notes, description 4  
Number type icons 52, 58, 59  
Menu Navigation 36  
Menu Outline 38  
Message folder  
draft box 79  
inbox 76  
outbox 78  
voice 82  
O
OK key 15  
voice mail 82  
Outbox folder 78  
Outbox, reviewing messages 78  
Outgoing 30  
Message Folders  
Erase messages 83  
Message settings, general 83  
Messages and lock mode 78  
Messages, creating 70  
Messages, receive in call 71  
Messaging 69  
P
Pause dial 23, 55  
Pauses, adding 54  
Phone Info  
Icon Glossary 140  
Phone Number 140  
Phone Number 140  
Phone Safety 153  
Phone Settings  
Types of Messages 70  
metroWeb 86  
How metroWeb Keys Work 88  
Launching metroWeb 86  
Using Links 87  
Language 131  
Using metroWeb 87  
Missed calls menu 31  
Mobile Shop 66  
Shopping and  
Picture message settings 85  
Picture messages  
online viewing 75  
receiving 75  
Send in camera mode 71  
Pictures  
downloading 66  
Mode  
call answer 18  
camera 21  
brightness 98  
169  
Quality 100  
shutter sounds 102  
zooming in 98  
Language 131  
Location Setting 122  
Ringer Type 127  
Theme 124  
TTY Mode 129  
Voice Privacy 130  
Volume 127  
Q
Quality, Pictures 100  
QWERTY Keypad 45  
Wallpaper 123  
Settings menu  
R
Receive messages in call 71  
Receive pic. messages 75  
Receive text messages 71  
Removing apps 68  
accessing 122  
Settings, picture messages 85  
Settings, text messages 84  
Shortcut to menus 38  
Shutter sounds 102  
Silence ringer 28  
Reset your phone 134  
Resolution, notes about 98  
Responsible Listening 151  
Restoring apps 68  
Silent mode  
entering 20  
exiting 20  
Software version, viewing 140  
Sound Settings  
Restriction 135  
Return to last menu 36  
Review calls 33  
Reviewing outbox 78  
Right soft key 15  
Ringer Type 127  
Volume 127  
Ringer Type 127  
Standard Limited Warranty  
Standby mode 19  
Store emergency #s 134  
Store numbers after a call 57  
S
SAR 141  
Save a number after a call 57  
Security sub menu 132  
Self timer 99  
T
Send key 16  
Setting  
Take pictures  
with flip open 96  
Taking pictures 96  
Talk mode 19  
Text entry modes 70  
Text message settings 84  
Text messages, receiving 71  
Text Modes  
Call Answer 128  
Settings 122  
Auto Answer 129  
Auto Retry 129  
Backlight 126  
Banner 125  
Data Settings 130  
Dialing Font 125  
changing 45  
Theme 124  
170  
Three-way calling 23  
Timer, calls 33  
Timer, camera 99  
Tip, description 4  
Tools 106  
Voice Setting  
About VoiceSignal 94  
Choice Lists 91  
Sensitivity 91  
Sound 93  
add new event 110  
alarm clock 113  
calculator 116  
calendar 109  
Voice Launch 94  
Voice SVC 89  
Volume 127  
W
memo pad 112  
world time 115  
Tools Menu  
accessing 106  
TTY Mode 129  
Wait 54  
Wallpaper 123  
Warranty Information 162  
World time 115  
Z
U
Zooming, pictures 98  
UL Certification 143  
Understanding Your Contacts 49  
Deleting a Contacts entry 64  
Editing an existing Contacts  
entry 53  
Finding a Contacts entry 50  
Understanding Your Phone 9  
Closed View of Your Phone 10  
Command Keys 15  
Display Screen 16  
Features of Your Phone 9  
Open View of Your Phone 12  
Using Abc Mode 47  
V
Version 140  
Vibrate mode 20  
View an event, scheduler 109  
Voice folder 82  
Voice mail  
checking 82  
listening to 8  
Voice Privacy 130  
171  

Transcend Information JETFLASH TS4GJF2C User Manual
Sony Operating Instructions ICF CD873L User Manual
Seagate Backup Plus STBW500900 User Manual
SanDisk ImageMate 415753 User Manual
Samsung SGH T959ZKATMB User Manual
Samsung SGH C210S User Manual
Samsung S3 User Manual
Samsung M7500 User Manual
Nokia N 3100 User Manual
Nokia Cell Phone 5200 User Manual