SCH-A970 Series
P O R T A B L E
A l l
D i g i t a l
M O B I L E
P H O N E
User Guide
Please read this manual before operating your
phone, and keep it for future reference.
YF10.01_WC_062105_F3
Licensed by Qualcomm Incorporated under one or more of the
followingpatents:U.S.PatentNo.4,901,307;5,056,109;5,099,204;
5, 101, 501; 5, 103, 459; 5, 107, 225; 5, 109, 390.
Printed in South Korea
GH68-06472A
Openwave® is a registered Trademark of Openwave, Inc.
RSA® is a registered Trademark RSA Security, Inc.
Disclaimer of Warranties; Exclusion of Liability
EXCEPT AS SET FORTH IN THE EXPRESS WARRANTY
CONTAINED ON THE WARRANTY PAGE ENCLOSED WITH
THEPRODUCT, THEPURCHASERTAKESTHEPRODUCT"AS
IS", AND SAMSUNG MAKES NO EXPRESS OR IMPLIED
WARRANTY OF ANY KIND WHATSOEVER WITH RESPECT
TO THE PRODUCT, INCLUDING BUT NOT LIMITED TO THE
MERCHANTABILITY OF THE PRODUCT OR ITS FITNESS FOR
ANY PARTICULAR PURPOSE OR USE; THE DESIGN,
CONDITION OR QUALITY OF THE PRODUCT; THE
PERFORMANCE OF THE PRODUCT; THE WORKMANSHIP
OF THE PRODUCT OR THE COMPONENTS CONTAINED
THEREIN; OR COMPLIANCE OF THE PRODUCT WITH THE
REQUIREMENTS OF ANY LAW, RULE, SPECIFICATION OR
CONTRACT PERTAINING THERETO. NOTHING
CONTAINED IN THE INSTRUCTION MANUAL SHALL BE
CONSTRUED TO CREATE AN EXPRESS OR IMPLIED
WARRANTY OF ANY KIND WHATSOEVER WITH RESPECT
TOTHEPRODUCT.INADDITION,SAMSUNGSHALLNOTBE
LIABLE FOR ANY DAMAGES OF ANY KIND RESULTING
FROM THE PURCHASE OR USE OF THE PRODUCT OR
ARISING FROM THE BREACH OF THE EXPRESS WARRANTY,
INCLUDING INCIDENTAL, SPECIAL OR CONSEQUENTIAL
DAMAGES, OR LOSS OF ANTICIPATED PROFITS OR
BENEFITS.
Table of Contents
Table of Contents
5
6
Table of Contents
7
8
Section 1: Getting Started
Topics Covered
• Turning Your Phone On and Off
• Setting Up Your Voicemail
• Understanding This User Manual
This section allows you to start using your phone by
activating your service, setting up your voicemail,
contacting customer support, or getting an
understanding of how this manual is put together.
Section 1: Getting Started
9
Turning Your Phone On and Off
Turning Your Phone On
1. Open the folder, then press
.
2. Your service provider’s name momentarily appears in the
display and the phone begins searching for a network
signal.
3. Once the phone finds a signal, the time, date, and day
appear in the display.
4. You’re now ready to place and receive calls.
IfthephoneisoutsideoftheVerizonWirelesscoverageor
roaming area, appears in the top of the display.
Turn Your Phone Off
Press and hold
powers off.
for two or more seconds. Your phone
Setting Up Your Voicemail
Voicemail allows callers to leave voice messages, which
can be retrieved any time.
Note: Once your voicemail account has been set up, you can use the
Voicemail selection 2 (under the Messaging menu) to view details of voice
messages in your voicemail box.
Voicemail Setup
Note: It is recommended that voicemail be setup while you are in CDMA
mode.
1. In standby mode, press and hold
or enter
10
Understanding This User Manual
or dial your own mobile number to dial
voicemail.
2. Press
to interrupt the greeting.
3. Follow the prompts in the new user tutorial to setup your
mailbox.
Voicemail Setup
1. In standby mode, press and hold
displays.
2. Press
and press
3. Press
Calling Voicemail
again, then enter your own mobile number
to dial voicemail.
to interrupt the greeting.
4. Follow the prompts in the new user tutorial to setup your
mailbox.
Listen to Voicemail
1. In standby mode, press and hold
, or dial your own mobile number and press
to dial voicemail.
, enter
2. You are then prompted to enter your password.
Understanding This User Manual
The chapters of this manual generally follow the same
order as the menus and sub menus in your phone. A
robust index for quick reference to most features begins
Also included is important safety information that you
should know before using your phone. Most of this
information is near the back of the guide, beginning on
Section 1: Getting Started
11
Notes and tips
Throughoutthisguideareiconsandtextthataresetapart
from the rest. These are intended to point out important
information, quick methods for activating features, to
defineterms,andmore.Thedefinitionsforthesemethods
are as follows:
• Notes: Explain alternative options within the current feature,
menu, or sub menu.
• Tips: Provide quick or innovative methods for performing
functions related to the subject at hand.
• Fast Facts: Are like snippets from the glossary. Fast facts
provides definitions in context and proximity to the menu or
feature in question.
• Important: Points out important information about the current
feature that could affect performance, or even damage your
phone.
12
Section 2: Understanding Your Phone
Topics Covered
• Features of Your Phone
• Front View of Your Phone
• Command Keys
• Understanding the Display Screen
• Battery
• Removable Memory Card Storage
• Phone Memory Storage
This section outlines some key features of your phone.
It also displays the screen and the icons that are
displayed when the phone is in use.
Section 2: Understanding Your Phone
13
Features of Your Phone
• Domestic and international voice and text messaging service
(available on participating networks).
• High speed data (CDMA 2000 1x Technology)
• EVDO 1x Technology
• Global Positioning (GPS) Technology
• PIM Functions
• MMS Messaging
• TXT Messaging
• PIX Messaging
• Flix Messaging
• E-mail Messaging
• Instant Messaging
• 2.0 Mega Pixel Camera
• Camcorder
• Voice Dial
• Speaker phone
• Removable Memory Card Storage
• Phone Memory Storage
• Bluetooth
• MP3
14
2. Display Screen Icons: Indicates the status of your phone,
including status icons, message indicators, signal
strength, etc.
3. Navigation Keys: This key allows you to scroll through
the phone menu options.
4. Left Soft Key Option: This key is used to navigate through
menus and applications by selecting the choice available
in the Left Soft key Option.
5. Send Key: Allows you to place or receive a call. In
standby mode, press the key once to access the recent
call log.
6. Special Function Keys: Enter’s special characters.
Performs various functions.
7. Power/Accessory Connector: The power/accessory
interface connector is used to plug in the charging
accessories and also connect any available accessory
cables to your phone.
8. Microphone: The Microphone allows the other caller to
hear you clearly when you are speaking to them.
9. Alpha-numeric Keys: Use these keys to enter numbers,
letters, and characters.
10. Clear Key: Deletes characters from the display when you
are in text entry mode. Press to return to the previous
menu or screen when navigating features on your phone.
16
Front View of Your Phone
11. End Key: Ends a call. If you press and hold the END key,
the power goes On or Off. When you receive an incoming
call, press to mute the ringer and send the call to
voicemail.
12. Center/OK Key: Pressing when navigating through a
menu accepts the highlighted choice in a menu.
13. Right Soft Key: This key is used to navigate through
menus and applications by selecting the choice available
in the Right Soft key Option.
Closed View
Features
14. Rewind Key: MP3 player rewind key.
15. Service Light: Flashes when phone is powered on.
Section 2: Understanding Your Phone
17
16. Stop Key: MP3 stop key.
17. Fast Forward Key: MP3 fast forward key.
18. Play/Pause Key: MP3 play or pause toggle key.
Closed View (Right)
Features
19. Camera/Video Key: Launches the Camera/Video
Recorder feature of your phone.
20. Options Key: When in Camera/Video mode provides
options available for each function. See "Take Pix" on
page 129 for available options.
18
Front View of Your Phone
21. Volume Key: Allows you to adjust the master volume in
standby mode (with the folder open) or adjust the voice
volume during a call. To mute the ringer during an
incoming call, press the volume key up or down. When
the folder is closed, press and hold the key, and sub LCD
displays.
22. Speaker Mode Key: Enables and disables speaker phone.
Closed View (Left)
Features
23. Camera Lens: The lens of your built-in camera/
camcorder.
Section 2: Understanding Your Phone
19
24. Headset Jack: Allows you to plug in an optional headset
for safe, convenient, hands-free conversations.
25. TransFlash Card Slot: This expansion slot allows you to
insert a TransFlash memory card to add additional
memory and storage capacity.
Command Keys
Functions for the soft keys are defined by what appears
above each in the display. There are two soft keys, the left
soft key ( ) and the right soft key ( ).
Left Soft Key
Some functions of the left soft key are as follows.
• In standby mode, press the Message (left) soft key ( ) to open
the Message menu.
• When the left soft key function is Settings, press the Settings
(left) soft key ( ) to view settings for the feature.
• When the left soft key function is Edit, press the Edit (left) soft
key ( ) to edit a Contact or Profile setting.
Right Soft Key
Some functions of the right soft key are as follows.
• When the right soft key function is Options, press the Options
(right) soft key ( ) to return to the previous menu.
• In standby mode, press the Contacts (right) soft key ( ) to
open your Contacts list.
Clear Key
The CLR key (
) is used to erase or clear numbers, text,
orsymbolsfromthedisplay.Youcanalsouse
toreturn
20
Command Keys
toapreviousmenuortoreturntostandbymodefromany
menu.
1. If you enter an incorrect character, briefly press
to
backspace (and delete) the character.
2. To erase the previous word in a sentence, press and hold
.
3. To back up one menu level, briefly press
4. To return to standby mode from any menu, press and
hold until you return to standby mode.
.
End Key
1. Press and hold the End key ( ) to turn on your phone.
2. Briefly press once to disconnect a call.
3. Press to return to standby mode from any menu, or
to cancel the last input.
Send Key
The Send key ( ) is used to answer calls, dial calls, and
to recall the last number(s) dialed, received, or missed.
1. Press
2. Enter a number and briefly press
3. Briefly press in standby mode to display a list of
recent calls to and from your phone.
4. Press twice in standby mode to call the most
recently dialed number.
5. Press to pick up a waiting call. Press
switch back to the other call.
once to answer calls.
to make a call.
again to
Section 2: Understanding Your Phone
21
Navigation Key
Use the directional keys on the navigation key to browse
menus, sub menus, and lists. Each key also acts as a
shortcuttolaunchapplications.Thedownnavigationkey
is user-definable. Press
when replying to prompts,
and jumping to highlighted links on the web.
Understanding the Display Screen
The top line of the display is reserved for icons that
indicate network status, battery power, signal strength,
and more. The following table lists some display icons
and their descriptions.
Display icons
Signal Strength: Always appears when your phone is
on and indicates the current signal strength. More lines
indicate a stronger signal.
Roaming Indicator: Your phone is outside your home
area. While roaming, another wireless provider may be
handling your call. The service rate for the call may be
higher than those made from within your home area.
Please refer to Verizon Wireless for roaming rates.
Digital: Appears when your phone is receiving digital
data.
1X Protocol: Indicates your phone is using the EVDO 1X
protocol.
EVDO: Appears when your phone is using the EVDO
protocol.
EVDO/1X: The 1X protocol is capable of high-speed
broadband data (3G).
22
Understanding the Display Screen
Note: 1X protocol is available only in the Verizon Wireless network.
EVDO/2G: Indicates your phone is using the EVDO 2G
protocol.
SSL: Indicates the secure socket layer is active transmits
your communications over the internet in an encrypted
format.
Voice Privacy: Indicates that Voice Privacy is enabled.
No service indicator: Your phone cannot find a signal
because you’re outside a service area. You cannot make
or receive calls. Wait for a signal or move to an open area
to find a signal. This indicator always appears when you
first turn on your phone and disappears once service is
located.
Dormant: Indicates no incoming or outgoing data.
Voice Call: Indicates a call in progress. When dialing a
number, this icon flashes until the call connects.
Data Call: Indicates a call in progress. When dialing a
number, this icon flashes until the call connects.
Alarm clock: The alarm clock is set.
E911: Global Positioning Service is set to On for location
and 911 calls.
Location On: Global Positioning Service (GPS) for 911 is
set to On for emergency calls only.
Bluetooth: Indicates that Bluetooth wireless
technology is active.
Section 2: Understanding Your Phone
23
Bluetooth Connected: Indicates Bluetooth wireless
technology is active and connected.
Battery Level: More bars indicate a greater charge.
When the battery is low, an empty battery icon flashes
and the phone sounds an alert, which indicates your
phone is about to shut down.
TTY: Indicates that TTY is enabled.
All Off: The ringer is silenced for all alerts, incoming
calls, and incoming messages. The phone alerts you by
vibration and a flashing service LED.
Alarm Only: Your phone will only ring when the set
alarm sounds.
Vibrate On: Your phone vibrates upon receiving a call.
Sound On, Vibrate On: Your phone rings and vibrates
upon receiving a call.
Speakerphone: Your phone switches to
speakerphone instead of earpiece.
Missed Calls: Your phone displays this icon when calls
are missed.
New Message: You’ve received a new text, page or web
alert message. You’re also notified of a new message by
animations and sound. You have one or more unread
voicemail messages in your voicemail box. (Only
applicable on Verizon Wireless Network.)
Calendar Appointment: Your phone displays this icon
when you have a calendar appointment scheduled.
Voicemail: You’ve received a voicemail message., page
or web alert message.
24
Understanding the Display Screen
Alarm On: Indicates that your phone has a set alarm.
Auto Answer: Automatic answer is enabled. Your phone
automatically picks up any calls after the designated time.
Dialogue boxes
Dialogueboxespromptforaction,informyouofstatus,or
warn of situations such as low memory. Dialogue boxes
and their definitions are outlined below.
• Choice
• Example: “Save message draft?”
• Reconfirm
• Example: Delete all received messages?”
• Performing
• Example: “Sending...” “Connecting...”
• Completed
• Example: “Message sent successfully!”
• Information
• Example: “New Message”
• Error
• Example: “System Error!”
• Warning
• Example: “Battery Low,” “Memory Full!”
Section 2: Understanding Your Phone
25
Battery
Note: This phone comes packaged with a partially charged rechargeable
standard Li-Ion battery and desktop charger.
Important: Although the phone can be used while the battery is charging,
the battery must be fully charged before first use, otherwise you could
damage the battery.
1. Insert the bottom end of the
battery into the phone
housing with the label side
down. The gold contacts on
the end of the battery should
match up with those on the
phone.
2. Push the top end of the battery down until it snaps into
place.
Remove the battery
1. Pull the battery release latch
toward the top of the phone.
The top of the battery should
pop up.
2. Use your finger to lift the
battery (top end first) up and
away from the phone.
Charge the Battery
YourphoneispoweredbyarechargeablestandardLi-Ion
battery. Only use Samsung-approved charging devices
26
Removable Memory Card Storage
and batteries. Samsung accessories are designed to
maximize battery life. Using other accessories may
invalidate your warranty and may cause damage.
Use the Desktop Charger
The desktop charger operates from a 120/220 VAC wall
outlet.
1. Plug the AC plug from the desktop charger into a
standard 120 VAC or 220 VAC wall outlet.
Note: You can use your phone while charging, however, the battery
charges faster if the phone is turned off.
Battery Indicator
Thebatteryindicator( )intheupper-rightcornerofthe
display indicates battery power level. Four bars indicate
a full charge, while an empty icon ( ) indicates an
almost empty battery. Two to three minutes before the
battery becomes too low to operate, a blinking empty
battery icon ( ) appears and a tone sounds. If you
continue to operate the phone without charging, it shuts
down.
Removable Memory Card Storage
TransFlashmemoryisatypeofremovableflashmemory
card designed specifically for mobile phones. Your A970
supports TransFlash memory which allows you to save
images or videos to the memory card instead of to the
memory in your phone.
Section 2: Understanding Your Phone
27
Note: Your phone does not come with the TransFlash memory card, it must
be purchased as an accessory. See your service provider for more
information.
The following file types can be saved to the TransFlash
memory card:
• Pix: Pictures that you have taken using your phone.
• Flix: Videos that you have taken using your phone.
• MP3/Music: MP3 files you have stored on your PC.
• Other Files: For other file types that can be saved to the
TransFlash memory card, see "File Viewer" on page 150.
To setup your camera to save pictures to the TransFlash
memory card:
1. In standby mode, press the
navigation key to highlight
Get Pix & Flix.
Menu, use the left
Get It Now. Press
2. Press
Take Pix. The camera is now active.
3. Press the right soft key Options.
4. Use the right/left navigation keys to advance to the
Settings category. Use the up/down navigation keys to
select the Memory option.
5. Use the up/down navigation keys to select the Card
option and press the
key.
Your pictures will now be saved to the TransFlash
memory card.
28
Removable Memory Card Storage
Note: If you remove your memory card, the location to save images will
automatically default to the internal phone memory. It will remain the
default even after you re-insert the memory card.
ToreviewyourstoredpicturesontheTransFlashmemory
card:
1. In standby mode, press the
navigation key to highlight
Get Pix & Flix.
Menu, use the left
Get It Now. Press
2. Press
My Pix,
Card to view pictures that have
been stored on the TransFlash memory card. Press
.
3. Use the navigational keys to select a picture and press
View to see the selected picture.
To setup your camcorder to save videos to the memory
card:
1. In standby mode, press the
navigation key to highlight
Get Pix & Flix.
Menu, use the left
Get It Now. Press
2. Press
Take Flix. The camcorder is now active.
3. Press the right soft key Options.
4. Use the right/left navigation keys to advance to the
Settings category. Use the up/down navigation keys to
select the Memory option.
5. Use the up/down navigation keys to select the Card
option and press the
key.
To review your stored videos in the memory card folder:
1. In standby mode, press the
Menu, use the left
navigation key to highlight
Get It Now. Press
Section 2: Understanding Your Phone
29
Get Pix & Flix.
2. Press My Flix,
Card to view videos that have
been stored on the TransFlash memory card. Press
.
3. Use the navigational keys to select a video and press
Play to see the selected video.
YoucanviewstoredpicturesandvideoonyourPCifyour
Transflash memory card is connected to your PC. Please
consult the instruction manual that came with your
TransFlash memory card for further instructions.
Phone Memory Storage
The following file types can be saved to the Phone
Memory Storage:
• Ringtones: Ringtones you have downloaded via the “Get It
Now” application.
• Pix: Pictures you have downloaded via the “Get It Now’
application.
• Flix: Video Clips you have received from other phones,
downloaded via the “Get It Now” application, or Video Clips
downloaded via V CAST.
30
Section 3: Call Functions
Topics Covered
• Making a Call
• Answering a Call
• Call History
• Roaming
• TTY
• Voice Signal
• Voice Memos
This section allows you to make or answer a call. It also
includesthefeaturesandfunctionalityassociatedwith
making or answering a call.
Section 3: Call Functions
31
Making a Call
1. At the standby screen, enter the number you want to call
using the keypad.
2. Press
.
Making Calls Using Contacts
Contacts are entries that you create to store names,
numbers, and other information for people or groups
of interest. If you’ve already entered information into
your Contacts list, you can recall and dial the contact
information on creating contacts.
1. At the Home Screen, press the right soft key Contacts.
2. Press or keys on the side of your phone until the
contact that you want to call is highlighted.
Tip: To quickly locate a name, press (or multi-press) any key on the keypad
that corresponds to the first, second, and/or third letters of the contact’s
name.
3. When the desired contact is highlighted, press
.
View for the contact appear in the display.
4. If the entry contains more than one number, use or
to highlight the desired number.
5. Press
to call the number.
Answering a Call
When you receive an incoming call, the Incoming screen
appearsinthedisplay,pressthe
keytoanswerthecall
32
Call History
or Ignore to send the call to voicemail, or Quiet to silence
the ringer.
Answering Call-Waiting Calls
• When you receive a call while on a call, the Incoming screen
displays. You can press and answer the new call or let the
new call go to your voicemail.
• If you choose
and answer the incoming call, the original
caller is placed on call waiting. To return to your original call
when you finish with an incoming call, press the Send key.
Call History
When you place, miss, or receive a call, a record of the
call is saved in Call History, which is a listing of the
different types of calls you can either receive or make.
These types of calls are listed below.
• Missed: Displays any missed calls.
• Received: Displays any received calls that were answered.
• Dialed: Displays all outgoing calls made from your phone.
• All: Displays all missed, received, and outgoing calls made from
your phone.
Viewing Call Information
Call History retains information such as the duration,
date and time, whether the call was received, dialed,
or missed.
1. At the Home Screen, press the ( ) Send key.
2. Press the down navigation key to highlight the desired
number.
Section 3: Call Functions
33
3. Once the desired number is highlighted, press
OPEN.
4. The following details appear in the display:
• “type” call: Where “type” indicates if the call was
missed, dialed, or received.
• Method: If the caller is in your Contacts list, the type of
call is indicated by a small icon to the left of the number
(Mobile, Home, Work, etc.). This option only appears if
the caller is in your Contacts list.
• Number: Displays the telephone number.
• Date: The date of the call.
• Time: The time of the call.
• Duration: The duration of the call.
5. Press the right soft key ( ) Options to display the
following options.
• Save: Save the number to your Contacts list.
• Details: Show details of the call. This option only
appears if the number is in your contact list.
• Erase: Delete the call from Call History.
• Lock/Unlock: lock or unlock the entry to prevent
accidental deletion.
• Erase All: Delete the entire Call History list at one time.
• View Timers: Select to view the call timers for your
phone.
6. Press the down navigation key to highlight an option.
Press
to enter the highlighted option’s sub-menu.
Call History Icons
When you view Call History, an icon to the left of the
number indicates the type of call.
34
Call History
Indicates a Missed call
Indicates a Dialed call
Indicates a Received call
Making Calls Using Call History
1. At the Home Screen, press
then press up or down
navigation key until the desired number is highlighted.
2. Press Open, then press to call the highlighted
number.
Creating Contacts Using Call History
1. At the Home Screen, press then press up or down
navigation key until the desired number is highlighted.
2. Press the right soft key Options. Use the up or down
navigation key to highlight Save, press
. Create
New is highlighted.
3. Press
• Mobile 1
to select from the following options:
• Mobile 2
• Home
• Work
• Fax
4. Press
to add a new contact, and then enter
information.
Section 3: Call Functions
35
5. Select the phone entry for the number you are adding,
and then press
6. Press Save when finished.
.
Delete Call History Entries
1. At the Home Screen, press
Send, then press up or
down navigation key until the desired number is
highlighted.
2. Press the right soft key ( ) Options. A pop-up menu
appears in the display.
3. Press the down navigation key to highlight Erase and
press
pop-up screen.
4. Press the
key. Select Yes or No at the ERASE ENTRY?
key.
Delete All Call History Entries
1. At the Home Screen, press
Send, then press up or
down navigation key until the desired number is
highlighted.
2. Press the
Open key.
3. Press the right soft key Options. A pop-up menu
appears in the display.
4. Press the down navigation key to highlight Erase All and
press
ENTRIES? pop-up screen.
5. Press the key.
key. Select Yes or No at the ERASE ALL
36
Roaming
Roaming
What is Roaming
Your phone can roam on other digital networks.
Roaming occurs when you travel outside a pre-
designated coverage area. The roaming icon displays
when roaming is active and extra charges may apply
when making or receiving calls.
Note: Some features may be unavailable while roaming.
Roaming Options
The following roaming options may be available
depending on your service plan:
• Home Only: Your phone is available for normal operation only in
the designated coverage area.
• Automatic: The preferred roaming list is used to acquire
service.
• Automatic-A: The preferred roaming list is used to acquire
service. If no preferred systems are found, any digital "A"
system is acquired.
• Automatic-B: The preferred roaming list is used to acquire
service. If no preferred systems are found, any digital "B"
system is acquired.
Note: Contact your service provider for information regarding preferred
systems.
To change your Roaming option, follow these steps:
1. Press the
Menu key. Use the right navigation key
to highlight
Settings & Tools.
Section 3: Call Functions
37
2. Use the down navigation key to highlight
System
and press the
key. System Select is highlighted.
3. Press the
key. Use the up or down navigation keys
to choose the setting you want, and press the
key.
TTY
Your phone is fully TTY compatible. Connect the TTY
equipment to the headset jack, which is located on the
left side of the phone above the TransFlash opening.
Before you can use your phone with a TTY device,
you’ll need to enable TTY functions in the phone.
1. Press the
Menu key. Use the right navigation key to
highlight
Settings & Tools.
2. Use the down navigation key to highlight
Settings and press the key.
3. Press TTY Mode and press the
Mode screen displays.
Call
key. The TTY
4. User the up or down navigation keys to choose from the
following:
• TTY Full
• TTY + TALK
• TTY + HEAR
• TTY Off
5. Press the
key to make your selection. The TTY
Mode Set screen displays.
Voice Signal
Voice Signal is advanced speech recognition software
that can be used to activate a wide-variety of functions
38
Voice Signal
on your phone. Voice Signal software automatically
voice activates all contacts for voice dialing and
searching, no pre-recording or training needed. Speak
phone numbers naturally to dial, and use voice
commands tolaunchapplicationsandnavigate phone
menus.
Voice Signal Settings
You can adjust the settings and preferences for Voice
Signal by opening the Voice Settings menu. Using this
menu, you can change the following Voice Command
features:
• Choice Lists: If Voice Signal is not absolutely confident that it
has correctly identified a name or number, it can display a
choice list of up to three possibilities, and prompt you to
confirm the correct one. You can control when choice lists
appear by changing the Choice Lists setting to the following:
• Automatic: Voice Signal displays a choice list when it is not
confident it has identified the correct choice from among
multiple alternatives.
• Always On: When there are multiple alternatives, Voice
Signal always displays a choice list.
• Always Off: Voice Signal never displays a choice list.
Instead, the application picks the best from among the possible
choices.
• Sensitivity: In Voice Signal, sensitivity controls the balance
between rejecting too much, which means the phone
frequently does not recognize names, numbers, or commands,
and rejecting too little, which means it frequently recognizes
something even if nothing was said. When Voice Signal rejects
an utterance, it displays a message such as “Please repeat…”
or “No match found.” If you frequently experience these
messages, you might be able to get better recognition by
adjusting the Sensitivity setting toward Reject Less. If you
Section 3: Call Functions
39
frequently experience false activations (Voice Signal detects a
wrong match), you might be able to get better performance by
adjusting the Sensitivity setting toward Reject More.
• Digit Dialing: Use the Digit Dialing menu to adapt digit dialing
to your voice.
• Adapt Digits: Lets you adapt digits, which can improve
voice recognition of phone numbers. Adaptation takes about
60 seconds.
• Reset Digits: Erases any digit adaptation you have done and
resets digit recognition to the factory default. If you have not
adapted digits, this option is grayed out.
• Sound: You can customize the Voice Signal user interface by
turning playback on or off for prompts, names, and numbers.
You can also change the speed and volume of name playback.
• Prompts: Turns playback on or off for prompts such as
“Please say a command.”
• Digits: Turns playback on or off for digits, for example, when
confirming a phone number.
• Names: Turns playback on or off for names.
• Name Settings: Adjusts the speed and volume of name
playback.
• VoiceMode: Use the VoiceMode menu to adapt VoiceMode to
your voice. You must adapt VoiceMode before you can use the
VoiceMode input mode in the text-messaging client.
• Adapt VoiceMode: Adapt VoiceMode to your voice, which
improves voice recognition of VoiceMode in the text-messaging
client.
• Reset VoiceMode: Erases any VoiceMode enrollment data
that is currently stored. If you have not adapted VoiceMode, this
option is grayed out.
• Tutorial: Displays the VoiceMode tutorial.
40
Voice Signal
• About: Displays information about Voice Signal including
version number, build number, and device number.
To access the Voice Signal Settings menu, follow these
steps:
1. At the Home Screen, press and hold
for two
seconds.
2. Press the left soft key Settings.
3. Use the navigation keys to select the setting you want to
change.
Adapting Voice Signal
Voice dialing works well for most people without special
adaptation. However, people with strong accents or
unique voice characteristics may receive better results
after adapting the system to match their voices.
You should adapt Digit Dial only if the system is
frequently unable to recognize your speech. After you
adapt Digit Dial, your phone is customized to your
voice, and your voice only. Others will not be able to
use it unless they reset the phone to factory defaults.
Adaptation involves recording several digit
sequences to adapt the system to the unique
properties of your voice. The adaptation process takes
about three minutes.
Tips for Adapting Digit Dial
• Adapt digits in a quiet place.
• Make sure you wait for the beep before starting to speak.
• Speak clearly, and say each digit distinctly.
Section 3: Call Functions
41
• If you make a mistake while recording a sequence of digits, or if
there is an unexpected noise that spoils the recording, re-
record that sequence.
• Only adapt digits if you regularly have problems with digit
dialing. Once adapted, digit dialing will not work as well for
other people using your phone.
• Adapt Digit Dial to your Voice
Digit Dial Adaptation
To access the Adapt Digits menu, follow these steps:
1. At the Home Screen, press (
) Menu. Use the right
navigation key to highlight
Settings & Tools.
2. Press
Call Settings, then
Voice Services.
3. Press
Train Word, then
Digit Dialing.
4. Adapt Digits is highlighted. Press the
key.
5. A short description of the Adapt Digits displays.
6. Read the description until you are comfortable to
proceed, then press
.
7. Your phone displays the first digit sequence and “Please
say” plays through the speaker followed by the four
digits appearing in the display.
Wait for the beep and repeat the digits using your normal
tone of voice.
8. After a moment, the phone plays back the recording and
prompts “Did the recording sound ok?” If the recording
was good, say “Yes.” If you need to re-record, say “No.”
If you say “No,” the phone prompts you to pronounce the
digits again. Wait for the beep and then re-record.
Repeat this step until you’re satisfied with the recording.
42
Voice Signal
9. After confirming that the recording sounds ok, repeat the
recording process with the next set of digits. After six
sets of digits, the phone asks whether you want to do
more adaptation. Answer “Yes.”
10. Repeat steps 4-6 for another six sets of digits. After the
sixth set of digits, the phone indicates that adaptation is
complete.
Reset Digit Dial Adaptation
This option erases an adaptation and resets Digit Dial
to its original state.
1. At the Home Screen, press (
) Menu. Use the right
navigation key to highlight
Settings & Tools.
2. Press
Call Settings, then
Voice Services.
3. Press
Train Word, then
Digit Dialing.
Note: If you have not performed the Adapt Digits function, the Reset Digits
option will not be accessible.
4. Highlight
Reset Digits and press the
key. The
Reset Digit Adaptation screen displays requesting
conformation of reset. Press
to proceed. Digit
Adaptation Reset is completed.
Voice Signal Options
The following is a list of functions that you can
perform using Voice Signal speech recognition on
your phone.
• Call <Name> <Loc.>: Dial by saying either a Name in your
Contacts list and the location (home, work, mobile)
Section 3: Call Functions
43
• Call <Number>: Dial by saying the number you want.
• Send Text<Name>: Send a text message to a number or to
someone in your Contacts List.
• Lookup <Name>: Open the contact record for any name in
your Contacts list.
• Go to <Menu>: Open any application installed on your device.
• Check <Item>: Provides details of your coverage, signal
strength, and battery level.
Call Digit Dialing
Digit Dial allows you to dial any phone number by
simply speaking the digits into the phone. No training
is necessary, and Digit Dial is programmed to
understand natural speech.
1. Press and hold
for two seconds.
2. After a brief pause, a list of optional commands appears
in the display and the audio prompt “Say a command”
plays through the speakerphone.
3. Say “Call” at a distance of 3-12 inches from the phone in
a natural voice.
4. “Say the Name or Number” plays through the
speakerphone.
5. To use Digit Dialing, say the area code and number that
you want to dial into the microphone, clearly and
naturally.
6. The number that you said is repeated through the
speakerphone and your phone dials the number.
7. If Voice Signal is not sure of the number that you said, a
list of possible matches appears in the display.
44
Voice Signal
8. You’re asked to confirm the correct number as Voice
Signal displays the results. Say “Yes” or “No” to confirm
or reject the number when prompted.
Call Name Dialing
To use Name Dial, you’ll need to have entries stored in
creating a Contacts list.
1. Press and hold
for two seconds.
2. After a brief pause, a list of optional commands appears
in the display and the audio prompt “Say a command”
plays through the speakerphone.
3. Say “Call” at a distance of 3-12 inches from the phone in
a natural voice.
4. “Say the Name or Number” plays through the
speakerphone.
5. To use Name Dialing, say the name of the contact that
you want to dial.
6. The name that you said is repeated through the
speakerphone and your phone dials the number.
7. If Voice Signal is not sure of the number that you said, a
list of possible matches appears in the display.
8. You’re asked to confirm the correct number as Voice
Signal displays the results. Say “Yes” or “No” to confirm
or reject the number when prompted.
9. The location is repeated through the speakerphone and
your phone dials the number.
Section 3: Call Functions
45
Send Text Message
1. Press and hold
for two seconds.
2. A list of commands appears in the display and the audio
prompt “Say a command” plays through the
speakerphone.
3. Say “Send Text” at a distance of 3-12 inches from the
microphone. “Say the Name or Number” plays through
the speakerphone.
4. After you say a name or number, you might be prompted,
“Did you say?” To confirm a name or number, wait for
the beep and then say “Yes.”
5. You can also choose the correct name or number from
the choice list using the phone’s arrow keys.
6. The Text Message client is launched. Enter your text
message.
To compose text messages using your voice, press the
left soft key and choose VoiceMode.The phone will start
listening when you press and hold the uppermost key on
the right hand side of the phone. Make sure you pause
between each word. For more information on using
VoiceMode, see "Creating a Text Message Using
Name Lookup
To perform a name lookup, you’ll need to have some
entries in your Contacts list.
1. Press and hold
for two seconds.
46
Voice Signal
2. A list of commands appears in the display and the audio
prompt “Say a command” plays through the
speakerphone.
3. Say “Lookup” at a distance of 3-12 inches from the
microphone. “Say the name” plays through the
speakerphone.
4. Say the name exactly as it is displayed in your Contacts
list, first name followed by last name.
5. The contact name appears in the display with other
information that you’ve entered for that contact.
Opening Applications
You can open an application or access a menu on your
phone using Voice Signal.
1. Press and hold
for two seconds.
2. A list of commands appears in the display and the audio
prompt “Say a command” plays through the
speakerphone.
3. Say “Go To” at a distance of 3-12 inches from the
microphone. A list of options displays and a prompt of
“Please choose” plays through the speakerphone. If the
option you desire is not listed, say “Next Menu” to scroll
to the next page.
4. The menu option spoken opens.
Checking Phone Status
Use the Check command to see and hear status
information from your phone, including its phone
Section 3: Call Functions
47
number, status, current signal strength, network
coverage, and battery level.
To check phone status:
1. Press and hold
for two seconds.
2. A list of commands appears in the display and the audio
prompt “Say a command” plays through the
speakerphone.
3. Say “Check” at a distance of 3-12 inches from the
microphone. A list of options displays and a prompt of
“Please choose” plays through the speakerphone.
4. The phone status menu option spoken is displayed.
Voice Memos
You can record a phone number, parking location, or
simple reminders using Voice Memos.
Recording Memos
1. At the Home Screen, press
Menu. Use the right
navigation key to highlight
Settings & Tools.
2. Press
Call Settings, then
Voice Services.
3. Press
Voice Memo. Press the left soft key New
to create a new Voice Memo.
4. Press the
REC key to begin recording. Press the left
soft key PAUSE or, if paused, press the RESUME
key to continue recording. Press the
stop recording.
STOP key to
48
Voice Memos
5. The new Voice Memo is saved with a system defined
name. Press the right soft key Option to choose from
the following:
• Detail Info: provides the voice memo title, length, size,
recorded date and time.
• Rename: allows you to rename the voice memo.
• Erase: allows you to delete the memo.
• Erase All: allows you to delete all voice memos saved.
Renaming Recordings
1. At the Home Screen, press (
navigation key to highlight
2. Press Call Settings, then
3. Press
) Menu. Use the right
Settings & Tools.
Voice Services.
Voice Memo. Use the navigation key until the
recording you want to rename is highlighted.
4. Press the right soft key Option. Press
Rename
to rename the Voice Memo.
5. Press and hold
until the current name for the
recording is deleted. Use the keypad to enter a new
name for the recording.
6. Press the
Save when finished or the right soft key
Back to exit and return to the previous menu.
Section 3: Call Functions
49
50
Menu Navigation
Accessmenus usingthenavigation keys, twosoft keys
, or use a shortcut.
1. In standby mode press the
Menu. The first of
several menus appear in the display.
2. Use the navigation keys to browse phone menus.
3. Press
to enter the menu or sub menu presently
appearing in the display.
Return to the Previous Menu
Press
to return to the previous menu.
Navigate Using Shortcuts
You can also access menus and sub menus using menu
numbers. This method is often called a “shortcut.” To
shortcut to a menu or sub menu, press
Menu, then
enter the menu and/or sub menu number(s) for the
feature in question. Use "Navigation Key Shortcuts" on
page 53, for looking up the menu shortcut number.
1. In standby mode, press
Menu. The Contacts menu
is launched.
2. Press the number of the menu, sub menu, and so on to
arrive at the desired feature.
3. Press
Business.
Menu, then press
Groups,
52
Menu Navigation
Navigation Key Shortcuts
In standby mode, press a navigation key (as illustrated
below) to launch its corresponding application.
TheShortCutmenucanbecustomized.Instandbymode,
press the
highlight
Menu, use the right navigation key to
Settings&Tools.Press
System
Short
Cut Key. The short cut key list displays. Use the
navigationkeytochangethesettingandpress
your selection.
tosave
The In-Use Option
Accessnumerousmenusandfeaturesevenwhileinacall.
Note: If the call is disconnected while accessing the In-Use Option, the In-
Use Option disappears from the display and the phone eventually returns to
standby mode.
1. While in a call, press the right soft key Options. The
following menu items appear in the display.
• Message: Open the Messages menu.
• Contacts: Open the contacts to view.
• Recent Calls: Display your recent incoming, missed and
outgoing calls.
• Send DTMF: Sends keypad tones.
Section 4: Menu Navigation
53
• Voice Privacy: Prevent recipients of your calls from seeing
your number on their display. Select from standard or
enhanced options.
• Voice Memo: Record a voice memo.
• Switch To Headset: Switches the device from handset to
Bluetooth wireless technology headset. This option only
appears once bluetooth has been activated.
• Switch To Phone: Switches the device from Bluetooth
wireless technology headset to handset. This option only
appears once the bluetooth headset has been connected.
2. Use the navigation key to highlight a menu. Press
to
open the highlighted menu or to activate the feature.
Menu Outline
Usethemenushortcutsonthefollowingpagestoquickly
accesssubmenus. Pressthe key to accessMenu, then
usethenavigationkeystohighlightthemenu.rightofthe
menu to jump to that menu, sub menu, or feature.
GET IT NOW
1: Get Tunes & Tones
1: Get New
2: Record New
2: Get Pix & Flix
1: Get V CAST Video
2: Get New PIX
3: Take Pix
4: Take Flix
5: My Pix
6: My Flix
7: Pix/Flix Place
3: Get Fun & Games
1: Get New
54
Menu Outline
4: Get News & Info
5: Get Going
1: Get New
MESSAGING
1: New Txt Msg
2: New Pix/Flix Msg
3: Inbox
4: Sent
5: Drafts
6: Voicemail
7: E-Mail
8: Mobile IM
9: Chat
CONTACTS
1: New Contact
2: Contact List
3: Groups
1: No Group
2: Business
3: Colleague
4: Family
5: Friends
4: Speed Dials
5: My Name Card
RECENT CALLS
1: Missed
2: Received
3: Dialed
4: All
5: View Timers
Section 4: Menu Navigation
55
SETTINGS & TOOLS
1: Tools
1: Calendar
2: Alarm Clock
3: World Clock
4: Notepad
5: Calculator
6: File Viewer
7: Mp3
2: Sounds
1: Master Volume
2: Call Sounds
3: Alert Sounds
4: Keypad Volume
5: Earpiece Volume
6: Service Alerts
7: Power On/Off
8: Alarm Sounds
3: Display
1: Banner
2: Backlight
3: Wallpaper
4: Display Theme
5: Power On/Off Animation
6: Service LED
4: System
1: System Select
2: Device Info
3: Location
4: Security
5: Language
6: Short Cut Key
5: Call Settings
1: Answer Options
56
Menu Outline
2: Auto Retry
3: TTY Mode
4: One Touch Dial
5: Voice Privacy
6: Data Settings
7: Voice Services
8: DTMF Tones
9: Airplane Mode
6: Time & Date
1: Set Time
2: Set Date
7: Clock Format
1: Main Clock
2: Front Clock
8: Ringer ID
9: Picture ID
0: Bluetooth
1: Activation
2: Search
3: Disconnect
4: Registered List
5: Bluetooth Settings
Section 4: Menu Navigation
57
58
Section 5: Entering Text
Topics Covered
• Changing the Text Input Mode
• Using Word Mode
• Entering Upper and Lower Case
• Entering Symbols
• Entering Numbers
This section outlines how to select the desired text input
mode when entering characters into your phone. This
sectionalsodescribeshowtousetheWordpredictivetext
entry system to reduce the amount of key strokes
associated with entering text.
Section 5: Entering Text
59
Changing the Text Entry Mode
1. While composing a message, press the right soft key
Options to display a pop-up menu with the following
options:
• Entry Mode: (This option appears when you select the
Options soft key while in the To: entry field). Choose the
method of text entry. Choose from:
• Word
• Abc
• ABC
• 123
• Symbols
• Shortcuts
• Add Quick Text: (This option appears when you select the
Options soft key while in the Text: entry field). Choose from
pre-written messages and phrases to save time. There are
initially 12 messages but you can add your own by pressing
the right soft key
New.
• Save As Draft: Save the message to your Draft folder.
• Priority Level: Save the message with a High or Normal
priority.
• Callback #: Displays the callback number in the text
message. Choose from On or Off.
• Validity Period: Save the message for the assigned period of
time.
• Deferred Delivery: Save the message to be delivered at the
assigned delivery date and time.
• Enh. Delivery Ack: Displays a pop-up screen notifying the
message sent has been received.
60
Using Word Mode
2. Press the left soft key
Add to access the following
options:
• Contacts: Launches the Contacts menu.
• Recent Calls: Lists all recent calls-dialed, received, or
missed.
Using Word Mode
Word recognizes the most commonly used word for any
sequence of key presses and inserts that word into your
message. It’s much faster than the traditional method of
textentry(Abc)andrequiresonlyonekeypressperletter
of the word that you’re spelling.
1. In standby mode, press the left soft key
Message,
then press
message.
New Txt Msg to compose a new text
2. Enter the phone number of the recipient, then press the
down navigation key to move to the Text field.
3. Press the left soft key
Abc to display a pop-up menu
containing text entry mode options.
4. Abc is highlighted. Use the up/down navigation keys to
highlight Word, then press
.
Now, for practice, enter the word “Samsung” into your
message by pressing each of the following keys only
once:
,
,
,
,
,
,
S
A
M
S
U
N
G
Word recognizes that the most frequently used word for
the sequence that you just entered is “Samsung.” If more
Section 5: Entering Text
61
than onewordshares the same sequence, Wordprovides
the most common of the two. Press
words in the dictionary, if available.
to display other
Entering Upper and Lower Case
• Enter characters while in ABC mode by pressing the key that
contains the desired characters for “H”.
• Press the key repeatedly to cycle through other available
characters for that key.
• Pause briefly when the desired character appears in the display
to accept the character and therefore insert it into the
message.
• Press
• To cycle between uppercase, lower case, and initial caps for
characters in ABC mode, briefly press
to enter a space.
.
Entering Symbols
Symbolmodeenablesyoutoentersymbolssuchas@or%
into a text message.
1. In standby mode, press the left soft key Message,
New Txt Msg to compose a new text message.
2. Enter the phone number of the recipient, then press the
down navigation key to enter text.
3. Press the left soft key Abc to display a pop-up menu
containing the following options.
• Voice Mode: Allows you to use the speech-to-text
function.
62
Entering Numbers
Note: The voice option does not function until you have performed the
Adapt text option in the ‘Adapting Voice Signal” on page 41.
• Word: Choose from the factory provided words or add to
your personal dictionary.
• Abc: Enter text with initial capitalization at the beginning of
each sentence.
• ABC: Enter text in all capital letters.
• 123: Enter numbers.
• Symbols: Allows you to enter symbols.
4. ABC is highlighted. Use the up/down navigation keys to
display Symbol, then press
. The first of four screens
containing symbols appears in the display.
5. Use the navigation left/right keys to page through the
other symbols, if necessary.
6. Enter the key that corresponds with the symbol that you
wish to enter. For example, press
point (!).
for an exclamation
7. Repeat steps 5 through 6 to insert as many symbols into
your message as desired.
Entering Numbers
Enternumbersintoatextmessagewhileinnumbermode
instructions on changing text entry modes.
• While in 123 mode, press the key containing the number that
you wish to insert into your message.
Section 5: Entering Text
63
64
Section 6: Understanding Your Contacts
Topics Covered
• Opening Contacts Menu
• Adding a Contact
• Adding Pauses
• Contact Groups
• Finding a Contacts Entry
• Editing an Existing Contact List Entry
• Deleting a Contact Entry
• Storing Numbers After a Call
• Speed Dialing
• My Name Card
• Finding My Phone Number
This section allows you to manage your daily contacts
by storing their name and number in your Contacts
menu. Contact entries can be sorted by name, entry, or
group.
Section 6: Understanding Your Contacts
65
Opening Contacts Menu
The Contacts menu provides access to powerful features
such as adding Groups, creating and sending V-cards,
and viewing the phone number assigned to your phone
by Verizon Wireless.
1. In standby mode, press
Menu. The Contacts menu
displays.
• New Contact: Add a number, e-mail, or web address to your
Contacts.
• Contact List: Find a phone number by Name.
• Groups: Add new or rename one of your five default groups.
• Speed Dials: Set a speed dial for a contact.
• My Name Card: Create a business card, which can then be
sent to others as an attachment
2. Use the navigation key to highlight the Contacts sub-
menu of your choice, then press
.
Contacts Icons
You can assign multiple entries to a contact. The icons in
the following table represent all available entry types
Mobile 1 icon. Enter a first mobile number for the entry in
this field.
Home icon. Enter a home number for the entry in this
field.
Work icon. Enter the work number for the entry in this
field.
Email 1 icon. Enter a first e-mail address for the entry in
this field.
66
Adding a Contact
Group icon. Select an available group to associate with
the entry in this field.
Ringtone icon. Select a ringtone to associate with the
entry in this field.
Mobile 2 icon. Enter a second mobile number for the entry
in this field.
Fax icon. Enter a fax number for the entry in this field.
Email 2 icon. Enter a second e-mail address for the entry
in this field.
Adding a Contact
WhenyouaddinformationtoyourContacts,youcanadd
it as a new entry or as an existing entry.
Method 1
1. In standby mode, press
Menu, the Contacts menu
opens.
2. Press
New Contact to enter the contact information.
3. Enter a name for the entry using the keypad.
4. Use the navigation key to highlight the appropriate type
(Mobile, Home, Work, E-mail, etc.). Once highlighted,
use the keypad to enter required information.
5. Use the navigation key to highlight other type fields, if
desired. Enter information using the keypad.
6. When you’re finished entering information for the entry,
press
Save to save the entry to your Contacts.
Section 6: Understanding Your Contacts
67
Method 2
You can add new numbers to the Contacts by simply
enteringthenumberwhilethephoneisinstandbymode,
then following the necessary prompts to complete the
process.
1. In standby mode, enter the number that you wish to save
using the keypad, then press the left soft key Save.
You’re prompted to select from Create New or Update
Existing.
2. Press
to enter the number as a Create New, or
press
to append the number to Update Existing.
3. If you selected Create New, the following types are
available.
•
•
•
•
•
Mobile 1
Mobile 2
Home
Work
Fax
4. If you selected Update Existing, proceed to step 7.
5. Use the up/down navigation keys to display the desired
type, then press the
key.
6. Enter a name for the entry using the keypad. Press the
left soft key ( ) Abc if you wish to select a different
method of text entry, such as Word, Abc, ABC, 123, or
Symbol.
68
Adding Pauses
7. When you’re finished entering information for the entry,
press
Save. The entry is saved to your Contacts. If
you selected Update Existing, the Contact List opens in
Search mode. Use the navigation key to browse through
entries, or enter the name of the entry using the keypad.
8. Once you’ve highlighted the entry you wish to append
the number, press
. An Update Existing pop-up
screen with the new information displays. Press the
key. The number is appended to the selected entry and
saved to your Contacts.
Adding Pauses
Calls to automated systems often require a password or
account number. Instead of manually entering numbers
each time, store the numbers to your Contacts along with
special characters called pauses.
• P pause: A hard pause stops the calling sequence until further
input from you.
• T pause: A two-second pause stops the calling sequence for
two seconds and then automatically sends the remaining
digits.
Note: Entering multiple two-second pauses extends the length of a pause.
For example, two consecutive two-second pauses cause a total pause
time of four seconds. Keep in mind pauses count as digits towards the 48-
digit maximum.
Contacts Groups
You can place any Contacts entry into one of five
categories, called “Groups.” Groups allow you to search
Section 6: Understanding Your Contacts
69
your Contacts faster, quickly send messages to one or
more group members, and more.
Note: By default, new entries to your Contacts are placed into the No Group
unless another group is specified.
View Groups
1. In standby mode, press the key (
(Groups). The following groups appear in the
display.
) Menu, then press
• No Group
• Business
• Colleague
• Family
• Friends
2. Use the navigation key to highlight the desired group,
then press
contents.
to access the group and view its
Move an Entry to Another Group
1. In standby mode, press the right soft key Contacts.
Use the navigation key to highlight the contact you wish
to move.
2. Press the left soft key Edit. Use the up/down
navigation key to scroll to the Group option.
3. Press the left soft key Set. Choose from the following
groups:
• No Group
• Business
• Colleague
70
Contacts Groups
• Family
• Friends
4. Use the navigation key to highlight the group containing
the entry that you wish to move, then press
5. Press Save. The selection has been saved to the
designated group.
.
Create a New Group
In addition to the five groups already in your phone, you
can create additional groups (a maximum of 30). New
groups can be named anything you like as long as their
names are within the 32-character limit.
1. In standby mode, press
Menu, then press
Groups. Your existing groups appear in the display.
2. Press the left soft key New. A New Group pop-up
menu displays with the “Enter new name” highlighted.
3. Press
SAVE to save. The Groups list now displays
the new group added.
Send a Text Message to Members of a Group
UseSendMessageintheGroupfeaturetosendamessage
to as many as 10 members of a group at once.
Note: Text messaging availability varies when roaming off the Verizon
Wireless Network.
1. In standby mode, press
Menu, then press
Groups. Your existing groups appear in the display.
2. Press the right soft key Options and highlight Send
Txt Msg. Press
.
Section 6: Understanding Your Contacts
71
3. Use the down navigation key to highlight the contacts in
the group to which you want to send a message. Press
the left soft key Done.
Note: You can mark up to 10 members of a group for message distribution.
If you try and mark an 11th member, you’ll be notified that 10 addresses
have already been selected.
4. Press
.
5. A pop-up menu appears in the display with Text
highlighted.
6. Enter the content of your message using the keypad.
7. To send the text message, press
Send.
Send a Pix Msg to Members of a Group
Note: Only available within Verizon Wireless Enhanced Services Area.
1. Follow steps 1 through 4 in the previous section entitled
2. With Text Msg and Pix Msg appearing in the pop-up
menu, use the navigation key to highlight Pix Msg, then
press
.
3. The list of addresses (or numbers) to which the message
will be delivered appears in the display.
4. Press
. The Create Pix/Flix Msg composer appears
in the display with the options:
• To: Enter the addresses (or numbers to which the message
will be delivered.
• Text: Add text to the Pix Msg.
72
Finding a Contacts Entry
• Pix/Flix: Add an image from the Pix or Flix Gallery to the
message.
• Sound: Add sound to the Pix Msg
• Subject: Add a subject to the Pix Msg.
• Name Card: Attach a Name Card or an entry in your
Contacts to the message.
5. Once you’ve finished adding the desired content to your
Pix Msg, you’re returned to the Pix Msg composer.
6. Press
Send to send the Pix Msg. The Pix Msg is
sent to the intended recipients.
Finding a Contacts Entry
From standby mode, you can quickly open the Contacts
list. Contacts is a quick way of viewing entries you’ve
stored in the Contacts list.
1. In standby mode, press the right soft key Contacts.
The Contact List displays.
2. In the Search field, enter the first and second letters of
the name you wish to search until it is highlighted.
Editing an Existing Contact List Entry
1. In standby mode, press the
Menu, then press
Contact List.
2. Use the navigation key to display the contact list entry
and press the left soft key Edit.
3. Use the navigation key to highlight the name, number, e-
mail address, or other field that you wish to edit.
4. Press
symbols.
to backspace and delete numbers, text, or
Section 6: Understanding Your Contacts
73
5. Press and hold
to erase all numbers in the
highlighted field.
6. Use the keypad to re-enter numbers, text, or symbols.
7. When you’re finished editing the entry, press
SAVE.
Your changes are saved.
Deleting a Contact Entry
1. In standby mode, press the
Menu, then press
Contact List.
2. Use the navigation key to display the contact list entry
and press the
View key.
3. Press the left soft key Erase.
4. A pop-up “Erase Entry?” screen displays.
5. Highlight Yes or No, then press
.
Storing Numbers After a Call
Once you’ve finished a call, you can store the number of
the caller to your Contact List.
Note: If the call was incoming and Caller ID information was unavailable,
then the store option is also unavailable.
1. After you press
to end your call, the call time, length
of call and phone number appears in the display.
2. Press the right soft key Save. You’re prompted to
confirm this as a Create New, or Update Existing.
3. Follow the on-screen prompts to designate other
information.
74
Speed Dialing
Store a number in standby mode
Storeaphonenumberbyenteringthenumberinstandby
mode, then press Save. Follow the screen prompts to
assign number types and other information.
Speed Dialing
Note: 1-Touch, 2-Touch, and 3-Touch dialing allows you to call numbers
stored in your Contact List quicker.
Speeddialingallowsyoutopressandholdakey(orkeys)
todialthenumberassociatedwiththosekey(s). Thereare
three types of speed dialing; 1-touch, 2-touch, and 3-touch
dialing.
Note:
is reserved for voicemail.
1-touch dialing
Call phone numbers assigned to memory locations 002 -
009 by pressing and holding the any of the 2 - 9 keys. For
example,tospeeddialthenumberassignedtolocation2,
pressandhold
untilthenameandnumberappearin
the display and the number is dialed.
2-touch dialing
Call phone numbers assigned to keys 010 through 099 by
briefly pressing the first key, then pressing and holding
the second key. For example, to speed dial the number
assigned to 013, briefly press
until the number dials.
, then press and hold
Section 6: Understanding Your Contacts
75
3-touch dialing
Call phone numbers assigned to memory locations 100
through 500 by briefly pressing the first and second keys,
then pressing and holding the third key. For example, to
dial location number 113, briefly press
and hold until the number dials.
,
, then press
Assign a speed dial location
1. In standby mode, press the
Menu, then press
Speed Dials. The Speed Dials screen displays with the
first available number highlighted.
2. Use the navigation keys to highlight the number you wish
to assign or enter the speed dial location using the
keypad, press the
SET key.
3. The Add Speed Dial screen displays.
4. Use the navigation keys to highlight the entry you want,
then press
5. At the pop-up screen, use the navigation key to highlight
Yes or No and press
.
.
6. Continue to assign speed dial entries or press the
key to return to standby mode.
My Name Card
My Name Card allows you to create a virtual business
card.Oncecompleted,youcansendthecardtorecipients
as a V-card attachment.
1. In standby mode, press the
Menu, then press
My Name Card.
2. My Name Card opens with the Name field highlighted.
76
Finding My Phone Number
3. Enter information in each of the fields as desired. Use the
navigation key to move between fields, then use the
keypad to enter information.
4. When finished, press
to save the V-card.
Finding My Phone Number
My phone # displays the ten-digit number assigned to
your phone.
1. In standby mode, press the
Menu, then press the
right navigation key to
Settings & Tools.
2. Press the
System key.
Device Info key. The My Number field is
. The mobile device and
identification number are displayed.
3. Press the
highlighted. Press
Section 6: Understanding Your Contacts
77
78
Section 7: Messaging
Topics Covered
• Types of Messages
• Message Folders
• Sending Pix/Flix Messages
• Receiving Pix/Flix Messages
• Retrieving New Messages
• Voicemail
• Creating and Sending New Messages
• Creating a Text Message Using VoiceMode
• Changing Message Settings
This section allows you to send or receive different
types of messages. It also includes the features and
functionality associated with messaging.
Section 7: Messaging
79
Types of Messages
Yourphoneiscapableofsendingemailandtextmessages.
Sendemailor text messages by simplyentering the email
address or the phone number of the recipient in the To:
<.........> or Send To field when creating a new message.
Message Folders
Your phone provides default message folders for your
Text, Pix and Flix, and Voicemail messages.
Sending Pix/Flix Messages
Note: Only available within Verizon Wireless Enhanced Services Area.
You can add sounds and attach a Name Card or Contact
entry to your Pix Msg. This is also known as Multimedia
Messaging (MMS).
1. In standby mode, press the left soft key Message
then press
New Pix/Flix Msg. Or in standby mode,
press the (
) Menu key and use the left navigation
key to highlight
Messaging then press
New
Pix/Flix Msg.
2. Enter the phone number or e-mail address of the
recipient (or recipients) using the keypad.
3. Press the right soft key Options to display a pop-up
menu that provides the following options:
• Entry Mode: Choose from Word, Abc, ABC, 123, Symbols
and Shortcuts modes of text entry.
• Preview: Shows the message before it is sent.
• Save As Draft: Save the message to your Draft folder.
80
Sending Pix/Flix Messages
• Priority Level: Save the message with a High or Normal
priority.
• Validity Period: Save the message for the assigned period
of time.
• Deferred Delivery: Save the message to be delivered at
the assigned delivery date and time.
• Remove Pix/Flix: Removes the selected Pix/Flix from the
message.
• Remove Sound: Removes the sound attached from the
message.
• Remove Name Card: Removes the attached name card
from the message.
4. Press the left soft key Add to select from the following
options:
• Contacts: Choose a number from your contacts list or select
the right soft key to select from the Groups menu.
• Recent Calls: Choose a number from the recent calls list.
• To Pix Place: Send the message to the Pix Place.
5. Press
once you’ve finished entering the number.
6. Press the down navigation key to add a message.
Compose your message, then press the down navigation
key. Pix/Flix is highlighted.
7. Press the left soft key Gallery to add a pix/flix. Press
.
8. Use the down navigation key to the Sound field, press
the left soft key Sounds to select a sound. Press
.
9. Press the down navigation key to the Subject field press
the left soft key Abc to change entry mode. Press the
right soft key Options to Add Quick Text. Press
.
Section 7: Messaging
81
10. Press the down navigation key to add Name Card. Press
the left soft key Add to select My Name Card or an
entry from your Contacts list. Press
.
11. Once all fields are complete, press
to send the
message to the intended recipient(s).
Receiving Pix/Flix Messages
When you receive a new Pix Msg, the options View now,
View later and Reject appear in the display.
Note: For the options to View now, View later and Reject to appear in the
display when you receive a Pix Msg, Auto retrieve mode must be set to Off
instead of On in the Message Settings sub menu.
1. When you receive a new Pix Msg, highlight the View
now option and press
. DOWNLOADING PIX/FLIX
MSG... appears in the display.
2. After downloading, the image (and text if any) contained
in the Pix Msg appear in the display.
3. Use the navigation keys to scroll through the message or
view the entire picture if necessary.
Receive Messages While in a Call
When you receive a message while in a call, the New
Messagedialogboxappearsinthedisplayalongwiththe
closed envelope icon ( ).
Reject a Pix Msg
Note: This feature is currently unavailable outside of the United States.
1. When you receive a new Pix Msg, highlight the Reject
82
Receiving Pix/Flix Messages
option.
2. Press
to reject.
View a Pix Msg Later
Note: Only available within Verizon Wireless Enhanced Services Area.
1. When you receive a new Pix Msg, highlight View later
and press
2. Later, when you wish to view the message, press the left
soft key Message,
3. Use the navigation key to highlight the unopened
message, then press . Specific directions for
.
.
Inbox
viewing the picture online at the Verizon Wireless
website appear in the display.
Inbox
Received messages of all types are stored in the Inbox
folder.
1. In standby mode, press the left soft key Message
then press
Menu key and use the left navigation key to
highlight Messaging then press Inbox.
Inbox. Or in standby mode, press the
2. Use the navigation key to highlight the message that you
wish to view.
3. Press
message.
OPEN to view contents of the highlighted
4. While viewing a message press the right soft key
Options to display the options listed.
Picture message options:
Section 7: Messaging
83
• Play Again: Replays the pix/flix message.
• Forward: Forward the message to another recipient.
• Erase: Pop-up prompts with Yes or No for deletion.
• Save Pix: Saves the picture received with the message.
• Save Sound: Saves the sound received with the message.
• Save Quick Text: Saves the text received in the message to
the Quick Text list.
• Save Name Card: Saves attached Name Card.
• Add To Contacts: Save the number of the sender to your
Contacts as a new entry or add to an existing entry.
• Lock/Unlock: Locks or Unlocks the message to prevent
deletion.
• Message Info: Provides the following information: From and
Callback Number, Priority, Msg Type, Size and if a Graphic,
Sound or Name Card were included in the message.
Text message options:
• Forward: Forward the message to another recipient.
• Erase: Pop-up prompts with Yes or No for deletion.
• Reply w/copy: Reply to the message with the original
message included. You can add up to 100 text characters.
• Save Graphic: Saves the graphic received with the
message.
• Save Sound: Saves the sound received with the message.
• Save Quick Text: Saves the text sent in the message to the
Quick Text list.
• Add To Contacts: Adds the sender’s information to your
contact list.
• Lock/Unlock: Locks or Unlocks the message to prevent
deletion.
84
Receiving Pix/Flix Messages
• Message Info: Provides the following information: Number,
Priority, Msg Type, Size and if a Graphic, Sound or Name Card
were included in the message.
5. Press the REPLY key to return a message to the sender.
Sent
Your phone stores messages in the Sent folder, regardless
of whether the message was successfully transmitted.
Verify if and when a message or e-mail was successfully
transmitted by enabling the Enh Delivery Ack feature.
Review Messages in the Sent Folder
1. In standby mode, press the left soft key Message
then press
Menu key and use the left navigation key to highlight
Messaging then press Sent.
2. Use the navigation key to highlight the message that you
wish to review, then press OPEN.
Sent. Or in standby mode, press the
3. While viewing the message, press the right soft key
Options to display the options listed.
Picture message options:
• Forward: Forwards the message to another recipient.
• Play Again: Replays the pix/flix message.
• Resend: Resends the message to the original recipient.
• Erase: Deletes the message.
• Add To Contacts: Adds the sender’s information to your
contact list.
• Lock/Unlock: Locks the message to prevent deletion.
• Save Quick Text: Saves the text sent in the message to the
Quick Text list.
Section 7: Messaging
85
• Message Info: Provides the following information: TO
Number, Priority, Msg Type, Size and if a Graphic, Sound or
Name Card were included in the message.
Text message options:
• Forward: Forwards the message to another recipient.
• Resend: Resends the message to the original recipient.
• Erase: Deletes the message.
• Add To Contacts: Adds the sender’s information to your
contact list.
• Lock/Unlock: Locks the message to prevent deletion.
• Save Quick Text: Saves the text sent in the message to the
Quick Text list.
• Message Info: Provides the following information: TO
Number, Priority, Msg Type, Size and if a Graphic, Sound or
Name Card were included in the message.
4. Use the navigation key to highlight the desired option.
5. Press
to perform the function for the highlighted
option.
6. From the Sent menu, press the left soft key Erase to
delete the message from the Sent folder. Highlight Yes to
delete, or No to return to the Sent menu.
Drafts
Draft messages are those that have been composed but
never sent. You can return to the Drafts folder at any time
to view, edit, or send a draft message.
Create a Draft Text Message
1. In standby mode, press the left soft key Message
then press
New Txt Msg. Or in standby mode, press
the Menu key and use the left navigation key to
86
Receiving Pix/Flix Messages
highlight Messaging then press
New Txt Msg.
2. Enter the phone number of the recipient, then press the
down navigation key.
3. Compose your message using the keypad, then press
the right soft key Options. A pop-up menu appears in
the display.
4. Scroll down with the navigation key until Save As Draft
is highlighted, then press
. A confirmation message
appears in the display and your message is saved to the
Drafts folder.
View and Edit Draft Messages
1. In standby mode, press the left soft key Message
then press Drafts. Or in standby mode, press the
Menu key and use the left navigation key to
highlight Messaging then press Drafts.
2. Use the navigation key to highlight the message that you
wish to view, then press EDIT. The message opens
in the Text field with the message text displayed.
3. Press the CLR key to backspace and delete any
current characters in the display, if desired. Press and
hold to erase a word at a time.
4. Press the right soft key Options. A pop-up menu
appears in the display with the options listed.
• Add Quick Text: Choose from up to 12 pre-loaded messages.
You can add additional messages by pressing the right soft key
New.
• Save As Draft: Save the message to your Draft folder.
Section 7: Messaging
87
• Priority Level: Save the message with a High or Normal
priority.
• Callback #: Displays the callback number in the text
message. Choose from On or Off.
• Validity Period: Save the message for the assigned period
of time.
• Deferred Delivery: Save the message to be delivered at the
assigned delivery date and time.
• Enh. Delivery Ack: Displays a pop-up screen notifying the
message sent has been received.
5. Use the navigation key to highlight the desired option.
Press
to perform the function for the highlighted
option.
6. Once you’ve returned to the message composer, press
to send the message, if desired.
Retrieving New Messages
While text messages from other phones are delivered
directly to your phone, Pix messages and Emails will be
stored in the Inbox of the message server and the server
will alert you to new messages. Therefore you need to
retrieve new messages to your phone and read them on
the phone.
Retrieving a Text Message
When you receive a message in standby mode, the
messageringersounds,(unlessturnedoff),andNewText
Msg appears in the display along with the closed
envelope icon ( ). The date and time of the message also
appear in the display.
1. Press the
key to View now, or press the down
88
Voicemail
navigation key to highlight View later and press the
key. The message is saved to your inbox where you can
view it later.
2. Press the right soft key Options to open the message,
where you have the option to Forward, Erase, Reply w/
copy, Save Graphic, Save Sound, Save Quick Text, Add
To Contacts, Lock and Message Info.
3. Press the
REPLY key to return a message to the
sender.
Voicemail
New voicemail alerts are sent via an SMS text message.
These messages indicate how many new and urgent
voicemails are in your box. When all voicemails has been
listened to, a message is sent notifying you there are zero
newmessageswaiting.Openthetextmessagetoviewthe
number of new and urgent voice messages in your
voicemailbox. If a caller leaves a callback number, this
number will also be sent via an SMS text message.
Receive Voicemail Messages
When you receive a new voicemail message you’ll hear a
sound and an SMS text message appears in the display.
1. Press the up/down navigation keys to select Listen Now
or Listen Later.
2. Press the
View Voicemail Messages in the Inbox Folder
1. In standby mode, press the key Menu, then press
Messaging, press
key.
the left navigation key to
Voicemail. Or press the left soft key Message and
Section 7: Messaging
89
press
Voicemail.
2. Press
OPEN to dial voicemail and retrieve your
message(s).
Creating and Sending New Messages
This section guides you through the procedure to send
various types of messages.
Creating and Sending Text messages
1. In standby mode, press the key
the left navigation key to Messaging, press
New Txt Message to compose a new text message. Or
Menu, then press
press the left soft key Message and press
New
Txt Message.
2. Enter the phone number of the recipient, or press the
right soft key Options to display a pop-up menu with
the following options listed:
• Entry Mode: Choose from Word, Abc, ABC, 123, Symbols
and Shortcuts modes of text entry.
• Save As Draft: Save the message to your Draft folder.
• Priority Level: Save the message with a High or Normal
priority.
• Callback #: Displays the callback number in the text
message. Choose from On or Off.
• Validity Period: Save the message for the assigned period
of time.
• Deferred Delivery: Save the message to be delivered at
the assigned delivery date and time.
• Enh. Delivery Ack: Displays a pop-up screen notifying the
message sent has been received.
90
Creating and Sending New Messages
3. After selecting or entering your recipients in the To field,
use the down navigation key to move to the message
composer.
4. Compose your message using the keypad. At any point
while composing a message, press the right soft key
Options to display the following options:
• Add Quick Text: Choose from up to 12 pre-loaded messages.
You can add additional messages by pressing the right soft key
New.
• Save As Draft: Save the message to your Draft folder.
• Priority Level: Save the message with a High or Normal
priority.
• Callback #: Displays the callback number in the text
message. Choose from On or Off.
• Validity Period: Save the message for the assigned period
of time.
• Deferred Delivery: Save the message to be delivered at the
assigned delivery date and time.
• Enh. Delivery Ack: Displays a pop-up screen notifying the
message sent has been received.
5. Use the navigation key to highlight an option. Press
to perform the function for the option, or to enter its
sub menu.
6. To send the message, press
Creating and Sending Pix/Flix Messages
1. In standby mode, press the key Menu, then press
.
the left navigation key to
Messaging, then press
New Pix/Flix Message to compose a new
message. Or press the left soft key Message and
Section 7: Messaging
91
press
New Pix/Flix Message.
2. Enter the phone number of the recipient, or press the
right soft key Options to display a pop-up menu with
the options listed
• Entry Mode: Choose from Word, Abc, ABC, 123, Symbols
and Shortcuts modes of text entry.
• Preview: Shows a preview of the message created.
• Save As Draft: Save the message to your Draft folder.
• Priority Level: Save the message with a High or Normal
priority.
• Validity Period: Save the message for the assigned period
of time.
• Deferred Delivery: Save the message to be delivered at the
assigned delivery date and time.
• Remove Pix/Flix: Erases the attached picture or movie.
• Remove Sound: Erases the attached sound.
• Remove Name Card: Erases the name card attached.
3. After selecting or entering your recipients in the To field,
use the down navigation key to move to the Text field.
4. Compose your message using the keypad.
5. Use the down navigation key to move to the Pix/Flix field.
Press the left soft key Gallery to select from My Pix
or My Flix. Press the
key.
6. The Phone option is highlighted or use the navigation
key to select Card. Press the
key to make your
selection.
7. Use the down navigation key to move to the Sound,
Subject and Name Card fields. Enter information if
desired.
92
Creating a Text Message Using VoiceMode
8. To send the message, press
SEND.
Creating a Text Message Using VoiceMode
About VoiceMode
VoiceMode TM from VoiceSignal Technologies is a simple,
fast, and convenient way to compose text messages on a
mobile phone. VoiceMode lets you use your voice to
dictate words, names, punctuation, and even
abbreviations (like LOL and TTYL), instead of keying
them in by hand.
To use VoiceMode when composing a text message, you
simply hold down the uppermost key on the right hand
side of your phone (the record button). Start dictating,
pausing briefly between each word. While you are
dictating, you will see words appear in your message.
These initial words that appear on the screen are
VoiceMode’s first guess at what you dictated. When you
release the record button, VoiceMode automatically
makescorrectionsbasedonthecontextofthephrase, and
display its best guess of the words recognized.
Adapting VoiceMode
Before you can use VoiceMode, you must adapt it to
recognize the special characteristics of your voice. The
adaptation process takes a few minutes to complete and
involves reading a list of 122 words, one word at a time.
To Adapt VoiceMode:
1. Find a quiet place for adaptation.
2. In standby mode, press and hold the 0 key at the bottom
of the keypad.
Section 7: Messaging
93
3. Press the left soft key Settings then press
VoiceMode.
4. Press
Adapt VoiceMode.
5. When you are ready to start adaptation, press the
key. If you or someone else has completed adaptation
earlier, the phone will ask if you want to start from
scratch or continue adapting the existing models. Select
Yes to discard existing adaptation data and start from
scratch, or select No to continue adapting the existing
data. If you are a new user, you should select Yes to start
from scratch.
6. Wait for the beep and then say each word as it appears
on the screen. Speak each word clearly and distinctly,
using a normal tone and volume. If the adaptation
process doesn’t detect a word, it will prompt you again
to speak the same word.
7. If you want to take a break, press the Pause key to
pause the adaptation process. When paused, continue
adaptation by pressing the Continue key.
8. After you say all 122 words, the phone will adapt
VoiceMode to your voice. This process takes
approximately one minute.
Note: If you press Cancel during adaptation, the phone will ask if you want
to save the adaptation data. Press Yes to save the data, or No to exit
without saving. If you do not complete adaptation, be sure to go back and
finish adapting to improve dictation recognition.
If you ever need to reset adaptation to its original state,
use the following procedure:
94
Creating a Text Message Using VoiceMode
1. In standby mode, press and hold the 0 key at the bottom
of the keypad.
2. Press the left soft key Settings then press
VoiceMode.
3. Press
4. When prompted, press the
or Cancel to exit without resetting the adaptation data.
Accessing and Using VoiceMode
Reset VoiceMode.
key to reset adaptation,
After adapting VoiceMode, you can start using it when
composing text messages.
To Start VoiceMode
1. In standby mode, press the key
the left navigation key to Messaging, press
New Txt Message to compose a new text message. Or
Menu, then press
press the left soft key Message and press
New
Txt Message.
2. You will be placed within the text message client. The
cursor must be placed in the Text: field to use
VoiceMode. Once the cursor is positioned in the Text:
field, select the left soft key Abc and press
VoiceMode.
3. If this is the first time you have entered VoiceMode, you
will see a VoiceMode tutorial screen appear. Select left
soft key Tutorial and then Next to step through the
VoiceMode tutorial.
Section 7: Messaging
95
4. At the end of the tutorial, you can choose whether or not
to show the tutorial again the next time you use
VoiceMode. Press
selection.
after you have made your
You will be placed back into the text message editor, with
VoiceMode selected as the input mode.
5. To activate VoiceMode, press and hold the uppermost
key that is on the right side of the phone (the record key).
VoiceMode beeps to indicate that you can begin
speaking.
Note: If you have not adapted, you will be prompted to do so after you
press the record key.
To Dictate Text Using VoiceMode
1. While holding down the record key, speak clearly and
pause distinctly between each word. For Example:
“When… speaking… COMMA… pause… briefly…
between… each… word… PERIOD”.
2. If a word is displayed incorrectly, KEEP speaking! When
you are done speaking, release the record key.
VoiceMode will make many corrections automatically.
3. After the record key has been released, the phone is not
listening but the text message application will remain in
VoiceMode. To switch to another mode, press the right
soft key.
Other Ways to Access VoiceMode
You can also address a text message by using your voice.
1. Press and hold the 0 key at the bottom of the keypad.
96
Creating a Text Message Using VoiceMode
2. After you hear “Say a Command,” say “Send Text”
followed by a name from your contact list or a valid
phone number. For example, you could say “Send Text
John Smith” or “Send Text 555 1212.”
3. The text message client will automatically open,
addressed to the recipient you specified. VoiceMode will
be the default input mode in the text editor.
Using VoiceMode Advanced Features
Using Choice Lists
Every time you dictate a word using VoiceMode, it
maintains a list of alternatives that closely resemble the
recognized word. These choice lists let you quickly
change a word that was not recognized correctly.
To use choice lists:
1. Use the left and right arrow keys to highlight a word you
want to change, and then press 0. A choice list appears
with possible matches for the word.
2. Use the up and down arrow keys to highlight the correct
word in the choice list, and press
leave the word as is.
, or press CLR to
When you select a word in the choice list, that word
automatically replaces the original recognized word in
the text message. You can view a choice list for a word
spokenbyvoiceasmanytimesasyoulike, aslongasyou
have not switched out of VoiceMode.
Spelling a Word
If a word is not recognized and does not appear in the
choice list, it might be because that word is not in the
Section 7: Messaging
97
dictation dictionary. In this case, you can spell out the
word manually. When you spell a word that is not part of
the dictation dictionary, the new word is added to the
dictionary. This enables VoiceMode to recognize the new
word the next time it is spoken.
To spell a word:
1. Press the 0 key to display the choice list for the word you
want to spell out.
2. Select
Spell Word. You will see an empty text box,
where you can manually spell the word using the
keypad.
3. As you start typing letters, you will see words with
similar spellings appear below the text box. Use the up
and down arrow keys to scroll the dictionary. While
scrolling the dictionary, the words will populate the text
box. Use the Back key to edit the entry in the text box.
4. After you are done typing the word, press
see the word you entered appear in the text editor.
Changing the Text Case
. You will
WhenusingVoiceMode,youcanspecifythecase(allcaps,
initial caps, or lower case) for text that you dictate. By
default, VoiceMode formats text according to the context
of the words in the message. For example, words
following periods are capitalized.
To specify the case of the next dictated word:
1. In VoiceMode, press the
key. The VoiceMode icon
key again to
changes to VOICE (all caps). Press the
change the text case icon to Voice (initial caps), or voice
(lower case). Voice is the default automatic text case.
98
Changing Message Settings
2. Dictate the word you want to appear in the specified
case.
Changing the text case will apply to all the words spoken
directly after specifying the case. You must manually
change the case back to the default.
Entering Punctuation Characters
VoiceMode recognizes most punctuation characters by
name. Refer to the appendix of this document for a
complete list of the names of punctuation characters you
can dictate.
Changing Message Settings
This menu allows you to define settings for your
messages sent or received on your phone. To access your
message settings, use the following steps:
1. In standby mode, press the
Menu, then press the
left navigation key to
Messaging, press the left soft
key Settings. Or press the left soft key Message
and press the left soft key Settings.
2. Use the navigation keys to access the following options:
• Auto Save: Saves all messages received or sent. Use the
navigation keys to select On, Off, or Prompt.
• Auto Erase: Erases all messages received or sent. Choose
from On or Off.
• Auto View Txt: Automatically displays the text message
when received. Choose from On or Off.
• Auto Receive: Automatically receives messages into your
Inbox. Choose from On or Off.
• Signature: Adds the signature text to each message sent.
Choose from None or Custom.
Section 7: Messaging
99
• Callback #: Displays the callback number in the text
message. Choose from On or Off.
• Voice Mail #: Enter the speed dial entry set for your
voicemail.
• Entry Mode: Sets the default entry mode for messaging.
Choose from Word, Abc, ABC, or 123.
• Quick Text: Displays the Quick Text pre-defined entries for
Text Msg and Pix Msg. Press the right soft key New to
add to the Quick Text list. Enter your new text and press the
key. The new Quick Text item shows in the first
position of the list.
100
Section 8: Changing Your Settings
Topics Covered
• Display Settings
• Shortcut Key
• Security Settings
• Voice Privacy
• Location Settings
• Changing Message Settings
• Call Settings
• Ringer settings
• Resetting Your Phone
• About Bluetooth
• Bluetooth Service Profiles
This section explains the sound and phone settings for
your phone. It includes display settings, security
settings, Bluetooth settings, call settings, and other
settings associated with your phone.
Section 8: Changing Your Settings
101
Display Settings
The Display sub menu affects the menu style, standby
mode animation, backlight settings, and more.
1. In standby mode, press the
Menu, use the right
navigation key to highlight
Settings & Tools. Press
Display. The following Display sub menus are
listed:
• Banner: Create your own personalized greeting that appears
in the display when your phone is in standby mode or choose
the ERI Banner which displays the network in which you have
subscribed.
• Backlight: Choose settings for Always On, Always Off, 5
seconds, 15 seconds, or 30 seconds.
• Wallpaper: Choose Pix (Pre-loaded or personal) or Flix to use
as the background display for your Main LCD. You may only
choose from your personal pix or pre-loaded pix for the Front
LCD.
• Display Theme: Choose from 4 preset colors used for
menu display.
• Power On/Off Animation: Choose the media that appears
in the display when you turn the phone on and off.
• Service LED: Turns Service LED on or off.
2. Use the navigation key to highlight the display sub menu
that you wish to edit, then press
.
3. Use the navigation key to select from the sub menu
options that appear in the display, then press
settings are saved.
. Your
102
Display Settings
Power On/Off Animation
Animation allows you to choose the multi-media or
pictures that appear in your phone’s display when you
turn it on, turn it off, and while the phone is in standby
mode.
Choose Power On or Power Off Animation
1. In standby mode, press the
Menu, use the right
navigation key to highlight
Settings & Tools. Press
(Display). The Display sub menus listed in the
display. Press
(Power On/Off Animation).
2. Use the navigation key to highlight Power On (or Power
Off), then press
.
3. Use the navigation keys to select from My Pix or Pre-
loaded Pix.
4. If you selected My Pix, press
Phone for pix you have
stored on your phone or
Card for pix you have stored
on your Trans-Flash Card. Once selection is made, press
the key to save to save settings.
5. If you selected Pre-loaded Pix, choose from the available
files, and press the key to save settings.
Choose the Wallpaper
1. In standby mode, press the
Menu, use the right
navigation key to highlight
Settings & Tools. Press
(Display). The Display sub menus listed in the
display. Press (Wallpaper). Main LCD and Front
LCD appear in the display.
2. Use the navigation key to highlight Main LCD or Front
LCD, then press
.
Section 8: Changing Your Settings
103
3. If you selected Main LCD, choose from the available
options of My Pix, My Flix, and Pre-loaded Pix and then
press
. If you selected Front LCD, proceed to step 5.
4. Follow the prompts to select the wallpaper that will
appear in the main LCD display while your phone is in
standby mode.
5. If you selected Front LCD, choose an image from the My
Pix or Pre-loaded Pix, then press
.
6. Follow the prompts to select the wallpaper to appear in
the Front LCD while your phone is in standby mode.
Banner
Banner allows you to create your own personalized
greetingthatappearsinthedisplaywhileyourphoneisin
standby mode.
1. In standby mode, press the
Menu, use the right
navigation key to highlight
Settings & Tools. Press
(Display). The Display sub menus listed in the
display. Press
(Banner).
2. Press
to create a personal banner for your handset.
Note: Press and hold
to erase an existing banner, if necessary.
3. Enter a word or short phrase (16 characters or less) to
appear in your phone’s display when the phone is in
standby mode.
4. Press
to save the new banner.
104
Short Cut Key
Backlight
Setthebacklightforthedisplayorkeypadtoremainonfor
a specified period of time or to remain on as long as the
folder is open.
Note: Prolonged backlight use drains your battery faster.
1. In standby mode, press the
Menu, use the right
navigation key to highlight
Settings & Tools. Press
(Display). The Display sub menus listed in the
display. Press (Backlight). The sub menus listed
appear in the display.
• Always On: The backlight is always on.
• Always Off: The backlight is always off.
• 5 Seconds: The backlight is on for 5 seconds before it dims.
• 15 Seconds: The backlight is on for 15 seconds before it
dims.
• 30 Seconds: The backlight is on for 30 seconds before it
dims.
2. Use the navigation key to highlight a sub menu.
3. Press
to enter the highlighted option’s sub menu
and change settings as desired.
Short Cut Key
Shortcut List allows you to select from up to eleven
applicationsthatappearinthedisplaywhenyoupressthe
up navigation key in standby mode.
1. In standby mode, press the
Menu, use the right
navigation key to highlight
Settings & Tools. Press
(System). The System sub menus listed in the
Section 8: Changing Your Settings
105
display. Press
Short Cut Key. The sub menus listed
appear in the display.
2. A list of sub menus appears in the display, use the
navigation key to highlight the desired sub menu, then
press
. The shortcut is added to the list.
Security Settings
The Security sub menu allows you to lock your phone, set
up emergency numbers, enable or disable voice privacy,
set restrictions, and other security options.
1. In standby mode, press the
navigation key to highlight
System.
Menu, use the right
Settings & Tools. Press
2. Use the navigation key to highlight Security, press
.
3. Enter the lock code (factory settings are the last four
digits of your telephone number). The following options
display:
• Common Code: Common code On uses a common
password for both device and location lock code. Common
code Off uses separate passwords for both device and location.
• Call Restrictions: Allows you to restrict the Outgoing,
Incoming, or Contacts list for your phone.
• Lock Mode: Allows you to lock the Device or Location.
• Edit Code: Allows you to change the Lock Code for the
Device or Location.
• Reset Phone: All settings (except Contacts) are reset to
factory default settings.
• Format Card: Allows you to format the TransFlash Memory
card.
106
Security Settings
Lock Phone
Lock Phone restricts the use of your phone with the
exception of outgoing calls to 911 and the three user-
programmed emergency numbers. Lock Phone allows
you to answer calls, but to place calls (except to
emergency numbers) you have to unlock the phone.
1. In standby mode, press the
Menu, use the right
navigation key to highlight
Settings & Tools. Press
System. The System sub menus are listed in the
Security. You’re prompted to enter
display. Press
the lock code. The default lock code is the last four digits
of your telephone number.
2. Enter the Lock Code. Several security sub menus appear
in the display.
3. Press
Lock Mode. Use the navigation key to
highlight Device or Location. Press the
key. The
following options display.
• Unlock: If locked, unlocks the device or phone, depending on
your selection.
• Lock: Your phone returns to standby mode. The the Lock Code is
required immediately to access any functions.
• On Power Up: The Lock Code is required whenever you
power up the phone. This option is only displayed when
Device is selected.
4. Press
option.
to perform the function for the highlighted
Section 8: Changing Your Settings
107
Change Lock
The default lock code is the last four digits of your phone
number. Change Lock allows you to change this code to a
lock code of your preference.
1. In standby mode, press the
Menu, use the right
navigation key to highlight
Settings & Tools. Press
System. The System sub menus listed in the
display. Press
Security.
You’re prompted to enter
the lock code. The default lock
code is the last four digits of your telephone number.
2. Press
Edit Code. Two options are available Device
and Location. Use the navigation keys to highlight your
choice and press
.
3. At the “Enter New Lock Code” prompt, enter the new
lock code. You’re prompted to confirm the new lock
code.
4. “Device or Location Lock Code Changed” message
appears in the display confirming that your lock code has
been changed.
Note: Your phone does not allow you to view the lock code for obvious
security reasons. If you change the lock code, be sure to write down or
memorize the new code.
Emergency #
Note: Emergency number 911 is hard-coded into your phone. You can dial
this number any time, even when the phone is locked or restricted. If you
call 911 an audible tone is heard and an emergency prompt appears in the
display for the duration of the call.
108
Voice Privacy
Important: DO NOT depend on this phone as a primary method of calling
911 or for any other essential or emergency communications.
Remember to always turn your phone on and check for
adequate signal strength before placing a call.
Call Emergency Numbers in Lock Mode
In Lock Mode, you can dial 911 to place an emergency
call.
Note: If you dial 911, your phone dials the emergency number immediately
(no prompt).
Voice Privacy
Note: This feature is only available on the Verizon Wireless network.
Voice Privacy (at the Enhanced setting) allows you to
prevent those you call from seeing your number in their
display when receiving your call. Voice privacy options
are Standard and Enhanced.
1. In standby mode, press the
Menu, use the right
navigation key to highlight
Settings & Tools. Press
Call Settings. The Call Settings sub menus listed
in the display.
2. Press Voice Privacy. The sub menus listed appear
in the display. Standard and Enhanced appear in the
display.
3. Use the navigation key to highlight the Voice Privacy
option of your choice, then press
saved.
. Your settings are
Section 8: Changing Your Settings
109
Restriction
Restriction allows you to restrict outgoing and incoming
calls. You can also restrict access to your Contacts list.
1. In standby mode, press the
Menu, use the right
navigation key to highlight
Settings & Tools. Press
System. The System sub menus listed in the
display.
2. Press
Security.
3. Enter the lock code, then press
4. Use the navigation key to select Outgoing Call,
Incoming Call, or Contacts, then press
Call Restrictions.
.
5. Use the navigation key to highlight On or Off, then press
. Your settings are saved.
Location Settings
Note: This feature is only available on the Verizon Wireless network.
The Location (GPS) setting identifies your location to the
network. You can fully enable this setting or set GPS to
work only in the case that you dial 911 from your phone.
1. In standby mode, press the
Menu, use the right
navigation key to highlight
Settings & Tools. Press
System. The System Settings sub menus listed in
the display.
2. Press Location. The Location screen displays.
• Location On: GPS location setting is on wherever the feature
is available.
110
Location Settings
• E911 Only: GPS location setting is on whenever you dial 911
only.
3. Use the navigation key to highlight an option.
4. Press
to select the highlighted setting.
Device Info
The Device Info sub menu allows you to view the
software and hardware information, your assigned
number, and an icon glossary for your phone.
1. In standby mode, press the
Menu, use the right
navigation key to highlight
Settings & Tools. Press
System. The System Settings sub menus listed in
the display.
2. Press
Device Info. My Number is highlighted.
Press
to display the Mobile Device and Identification
numbers.
3. Press
to view the software, PRL, ERI, Browser, Get it
Now, and Hardware versions availabe on your phone.
4. Press
description.
5. Press to return.
Language
to view the list of icons with a brief
Change the display language from English to Español or
vice versa using the Language sub menu.
1. In standby mode, press the
Menu, use the right
navigation key to highlight
Settings & Tools. Press
System. The System sub menus listed in the
display. Press
Language.
Section 8: Changing Your Settings
111
2. Use the navigation key to select the language of your
choice, then press
.
Changing Message Settings
The Msg Setting sub menu allows you to define default
settings for all message types.
Message Settings
1. In standby mode, press the
navigation key to Messaging. Press the left soft key
Settings. The following options listed appear in the
display.
Menu, use the left
• Auto Save: Set the text message auto save option to On, Off,
or Prompt.
• Auto Erase: Set the text message auto erase option to On or
Off.
• Auto View Txt: Turn Auto View Txt on or off. Direct View
immediately displays the content of a message as it is received.
• Auto Receive: Turn the Auto Receive on or off. Receives
messages without manually contacting the server.
• Signature: Insert a signature into all outgoing text messages.
You also have the option to create a custom signature.
• Callback #: Turn on or off the Callback # display when
sending a text message.
• Voice Mail #: Turn on or off the Voicemail # display when
sending a text message.
• Entry Mode: Set the default entry mode when creating a text
message. Choose from Word, Abc, ABC, or 123.
• Quick Text: View and edit any of the pre-composed
messages in your Quick Text list.
112
Changing Message Settings
2. Use the navigation key to highlight the desired setting.
Press
to perform the function for the highlighted
option or to enter its sub menu.
Entry Mode
UseEntryModetoselectthedefaultmethodoftextentry.
1. In standby mode, press the Menu, use the left
navigation key to Messaging. Use the down
navigation key to highlight New Pix/Flix Msg.
2. Press the left soft key Settings. Press
Entry
Mode. The options listed in the following table appear in
the display.
• Word: Enter text into messages using Word.
• Abc: Enter initial capitalization text into messages using
multiple key presses.
• ABC: Enter all capitalization text into messages using multiple
key presses.
• 123: Enter numeric values in a text message.
3. Use the navigation key to highlight the default method of
text entry, then press
. Your settings are saved.
Callback #
Use Callback # to view or modify the callback #. The
Callback # can be inserted into all outgoing messages,
thereby notifying the recipient(s) of your phone number.
1. In standby mode, press the
Menu, use the left
navigation key to Messaging.
2. Press the left soft key Settings. Press
Callback
#. The callback # appears in the display.
Section 8: Changing Your Settings
113
3. Use the CLR key
Press and hold CLR
the display.
to backspace and delete numbers.
to delete all characters from
Enter a new callback # number using the keypad, then
press to save your changes.
Auto Erase
Use Auto Erase to set the disposal method of messages
after they are read.
1. In standby mode, press the
Menu, use the left
navigation key to Messaging.
2. Press the left soft key Settings. Press
Auto
Erase.
3. Use the navigation key to highlight On or Off.
4. Press
are saved.
to select the highlighted option. Your changes
Voice Mail #
Use Voice Mail # to view or modify your voicemail
number.
1. In standby mode, press the
navigation key to Messaging.
2. Press the left soft key Settings. Press
Menu, use the left
Voice
Mail #. The Enter Number field is highlighted and *86
appears in the display.
3. Use the CLR key
Press and hold CLR
the display.
to backspace and delete numbers.
to delete all characters from
114
Call Settings
4. Enter a new number and press the
key to save your
changes.
Call Settings
CallSettingsallowsyoutoselectthemethodforanswering
incoming calls, setting redial options, setting data rates
for data calls, voice services, and more.
Answer Options
AnswerOptionscontainsthesubmenusCallAnswerand
Auto Answer. Call Answer allows you to select the
method for answering incoming calls, while Auto
Answer allows you to select the delay time before a call is
picked up.
Call Answer
1. In standby mode, press the
Menu, use the right
navigation key to highlight
Settings & Tools. Press
Call Settings. The Call Settings sub menus listed
in the display.
2. Press Answer Options. The following options
appear in the display.
• Folder Open: Calls are answered when the folder is
opened.
• Any Key: Calls are answered when any key is
pressed.
• Send Only: Calls are answered when the
key is
pressed.
• Auto Answer: calls are answered automatically with
a 1, 3 or 5 second delay.
Section 8: Changing Your Settings
115
3. Use the navigation key to highlight the method you wish
to use for answering calls, then press
Auto Retry
.
Auto Retry automatically redials busy numbers after a
preset period of time.
1. In standby mode, press the
Menu, use the right
navigation key to highlight
Settings & Tools. Press
Call Settings. The Call Settings sub menus listed
in the display.
2. Press Auto Retry. The following options appear in
the display.
3. Use the navigation key to highlight one of the following
options
• Off
• Every 10 Seconds
• Every 30 Seconds
• Every 60 Seconds
4. Press
the Call Settings sub menu without making a selection.
Data Settings
1. In standby mode, press the
navigation key to highlight
to select the option, or press
to return to
Menu, use the right
Settings & Tools. Press
Call Settings. The Call Settings sub menus listed
in the display.
2. Press Data Settings. The following options appear
in the display. Press the key to choose from the
following options:
• Data Off: Phone operates in normal voice call mode.
116
Ringer Settings
• Data For Next Call: Data call is enabled for next call only.
Phone will reset to Data Off mode after call.
• Data Until Powered Off: Phone will remain in Data Mode
until phone is powered off.
Ringer Settings
1. In standby mode, press the
Menu, use the right
navigation key to highlight
Settings & Tools. Press
Sounds. The Sounds sub menus listed in the
display.
2. Press the
Available options are:
Call Sounds. Press
Call Ringtone.
• Get New
• Beep Once
• Bell 1-5
• Melody 1-10
• No Rings
• Any Downloaded Ringtones
3. Press
Call Vibrate to set the Call Sounds to vibrate.
4. Press
to save the setting. The phone returns to Call
Sounds submenu.
Resetting Your Phone
Reset Phone returns all setup options to their factory
default.
1. In standby mode, press the
Menu, use the right
navigation key to highlight
Settings & Tools. Press
System. The System sub menus listed in the
display.
Section 8: Changing Your Settings
117
2. Press the
Security, and enter the lock code. Press
Reset Phone. A prompt appears in the display
asking if you wish to restore default settings (except for
the Contacts).
3. Press No to return to the Security list.
About Bluetooth
Bluetooth is a short-range wireless communications
technology capable of exchanging information over a
distance of about 30 feet without requiring a physical
connection.
Unlike infrared, you don't need to line up the devices to
beam information with Bluetooth. If the devices are
within a range of one another, you can exchange
information between them, even if they are located in
different rooms.
Bluetooth Service Profiles
Actually, the Bluetooth specification is a protocol that
describes how the short-range wireless technology
works, whereas individual profiles describe the services
supported by individual devices. Profiles reduce the
chance that different devices will not work together.
Your phone supports the following profile services:
• HSP: Mono-headset profile
• Bluetooth handsfree kit support *
* For vehicle/accessory compatibility, go to www.verizonwireless.com/bluetoothchart
Phone does not support Bluetooth OBEX profiles.
118
Bluetooth Service Profiles
Activation
When the Bluetooth radio is turned on, you can use the
Bluetoothfeaturesavailable.WhentheBluetoothradiois
turned off, you cannot send or receive information via
Bluetooth. To save battery life or in situations where
radio use is prohibited, such as airline traveling, you can
turn off the Bluetooth wireless technology headset.
1. In standby mode, press the
Menu, use the right
navigation key to highlight
Settings & Tools. Press
Bluetooth. The Bluetooth sub menus listed in the
display.
2. Press the
Activation.
Note: If activated, the
Bluetooth icon displays.
3. Select On to activate or Off if already activated.
4. Press the key to save changes.
Search
This option searches for a recognized Bluetooth wireless
technology device.
1. In standby mode, press the
Menu, use the right
navigation key to highlight
Settings & Tools. Press
Bluetooth. The Bluetooth sub menus listed in the
display.
2. Press the
active Bluetooth wireless technology device (laptop or
headset) or press Audible Device for the Bluetooth
Search. Press
All to search for any
wireless technology headset or the hands-free car kit
headset.
Section 8: Changing Your Settings
119
Note: If you have NOT already activated Bluetooth, a pop-up message
“BLUETOOTH IS NOT ACTIVATED. BLUETOOTH ON?” displays. Press Yes to
activate or No to exit.
3. Press the
key to save changes.
Note: Individual bluetooth accessories may have their own operational
requirements. Please review the information supplied with your accessory
to insure proper pairing and operation.
Disconnect
This menu provides the option to disconnect the
Bluetooth connection. To disconnect, use the following
procedures:
1. In standby mode, press the
Menu, use the right
navigation key to highlight
Settings & Tools. Press
Bluetooth. The Bluetooth sub menus listed in the
display.
2. Press the
Disconnect. If you have an active
Bluetooth connection, Yes is highlighted. Press the
key to disconnect, or highlight No to cancel.
Registered List
This menu provides a list of Bluetooth wireless
technologydevicesaccessedbyyourhandset.Toviewthe
registered list, use the following procedures:
1. In standby mode, press the
Menu, use the right
navigation key to highlight
Settings & Tools. Press
Bluetooth. The Bluetooth sub menus listed in the
display.
120
Bluetooth Service Profiles
2. Press the
accessed devices displays. Highlight the device and
press the Connect key. The connection is made.
Registered List. A list of previously
3. If you are already connected to the device highlighted, a
pop-up message “(device name) IS CONNECTED
ALREADY DISCONNECT?” displays. Press Yes to
disconnect or No to cancel.
Bluetooth Settings
The Bluetooth wireless technology settings menu
provides the ability to view and change the device name,
show the visibility, and set the security for the device.
1. In standby mode, press the
Menu, use the right
navigation key to highlight
Settings & Tools. Press
Bluetooth. The Bluetooth sub menus listed in the
display.
2. Press the
Bluetooth Settings. The Bluetooth sub-
menu displays with the following options displayed.
• My Device Name: shows the handset name. You may
change this name by using the left soft key abc. Enter the
text and press the
key.
• Visibility: allows other users to see your accessibility. Select
On for other devices to see your device, or Off for no visibility.
• Security: allows you to set the set the security at High or
Low.
Section 8: Changing Your Settings
121
122
Section 9: Multimedia
Topics Covered
• Get It Now
• Get Tunes & Tones
• Get Pix & Flix
• Get V CAST Video
• My Pix
• My Flix
• Pix/Flix Place
• Get Fun & Games
• Get News & Info
• Get Going
• How Keys Work
This section describes how you receive tunes, tones,
images, games, news and information. You can also
take and send pictures and video from your phone.
Section 9: Multimedia
123
Get It Now
The Get It Now menu provides sub-menus to get tunes &
tones,pixandflix,fun,games,newsandinformation.You
canalsoviewmemoryinfotoseehowmuchspaceyou’ve
used (and have left) for stored media. Use the following
steps for each Get It Now sub menus.
1. In standby mode, press the
navigation key to highlight
right soft key Info.
Menu, use the left
Get It Now. Press the
2. The Get It Now Info menu displays with System Info
highlighted. Press
to view the memory status. Press
the
key to return.
3. Press
Memory Info to display the memory available
for My Pix, My Flix and Downloads. Press the
to return.
4. Press
Press the
5. Press
key
View Log to see the file transfer activity.
key to return.
Help to display a list of frequently asked
questions. Use the navigation key to highlight an item
and press the key to display help text. Press the
key to return.
Get Tunes & Tones
This menu allows you to get new, record new, and set
tunes and tones as your ringtone.
1. In standby mode, press the
Menu, use the left
navigation key to highlight
Get It Now. The Get
Tunes & Tones menu is highlighted, press
.
124
Get Tunes & Tones
2. To get new Tunes & Tones press
Get New. Press
New Provider, you are connected to the Get It Now
server and presented with available provider
applications.
3. To record a new tune or tone, press
Record New.
The New Voice Memo screen displays. Press the
key to begin recording. Press the left soft key Pause
to pause or the
key to stop. Your new voice memo
is added to the current ringtone list.
4. Use the down navigation key to highlight the new
recording and press the right soft key Options.
5. Highlight the Rename option and press the
6. Enter a name and press the key.
key.
7. Press the left soft key Erase to delete the recording.
8. Use the down navigation key to select a ringtone, and
press the right soft key Options. The following
options are available for standard and downloaded
ringtones:
• Set As Ringtone: set as ringtone for your phone.
• Set As Ringer ID: set as ringtone for a specific group.
• Rename: change the name of the ringtone (downloaded
ringtones only).
The following options are available for recorded voice
memos:
• Rename: change the name of the ringtone.
• Move: move the ringtone to your memory card.
9. Highlight an option and press
.
Section 9: Multimedia
125
Get Pix & Flix
This menu allows you to get new pix and flix from the
internetortakenewpixorflixusingyourphone’scamera.
You can also view the saved pictures.
Get V CAST Video
V CAST, the next generation wireless technology that
unveils a whole new multimedia experience at your
fingertips, provides access to vibrant, full-color content
fromsomeofthebiggestnamesinentertainment.V CAST
is your link to video on demand, which allows you to
viewordownloadvideoclipsthatcontainbreakingnews,
sports highlights, weather and more.
For additional information regarding V CAST Video and
its’ use, see www.verizonwirless.com.
Note: To access and download videos, you must have the
displayed.
icon
Browsing, Selecting and Playing Video Clips
1. In standby mode, press the
navigation key to highlight
Pix & Flix and press
Menu, use the left
Get It Now. Highlight Get
or press the right navigation
key to display the Get It Now menu, highlight Get Pix &
Flix and press
.
2. The Get V CAST Video option is highlighted. Press
.
3. Use the left or right navigation keys to highlight the V
CAST Video category you want.
126
Get V CAST Video
4. After choosing the category you want press
. Choose
a sub category, if applicable, by using the navigation
keys or by entering the short-cut key number and press
.
5. Use the navigation key to highlight a video and read its
description and press
6. Highlight Yes to accept charges, if applicable, and then
press . After connection and buffering occurs, the
VIEW.
video clip begins.
Downloading a Video Clip
1. Launch V CAST Video and select a video you want to
save. For information about launching your video player
and choosing a video clip, review the previous section,
“Browsing, Selecting and Playing Video Clips” above.
2. Read the description of the video clip you want to
download, then press the right soft key Options.
3. Highlight Save Video and press
4. Highlight Yes to accept charges, if applicable, and then
press . The video download begins.
.
5. Once the download is completed, “Download complete.
Play video now?” appears in the display.
6. Select Yes and press
to view the video. The video
clip is saved to V CAST Video in the My Flix. Select No
to return to the V CAST Video sub-menu.
Note: Not all video content available can be downloaded to your phone;
however, all content is available for viewing.
Section 9: Multimedia
127
Deleting Video Clips
1. Launch V CAST Video. For information about launching
your video player, review "Browsing, Selecting and
Playing Video Clips" on page 126.
2. Press the right soft key Options. My Clips is
highlighted.
3. Press
. The clips you have downloaded are listed.
4. Use the navigation key to highlight the video you want to
erase and press the right soft key Options. Erase is
highlighted.
5. Press
. Highlight Yes when the confirmation screen
displays, then press
.
Using the Video Gallery
The video clips you save are stored in a folder named V
CAST Video in My Flix. You can access this folder
without launching the V CAST Video application and
delete your saved video clips directly.
1. In standby mode, press the
navigation key to highlight
& Flix.
Menu, use the left
Get It Now. Press Get Pix
2. Press
3. Use the navigation key to highlight V CAST Video, then
press
My Flix. Highlight
Phone and press
.
.
4. Use the navigation key to highlight the video you want to
delete and press the right soft key Options.
5. Use the navigation key to highlight Erase and then
press
.
128
Get V CAST Video
6. Highlight Yes to confirm that you want to erase the saved
clip, then press
.
Configure Alerts for New Video Clips
1. Launch V CAST Video. For information about launching
your video player, review "Browsing, Selecting and
Playing Video Clips" on page 126.
2. Use the right and left navigation keys to select the V
CAST Video categories you want to configure an alert.
3. Choose a sub category if applicable, then press the right
soft key Options.
4. Highlight Alerts and press
.
5. Highlight Configure Alerts and press
.
6. Select the alert content you want, and then select to
Save.
Note: Fees apply for text messages/alerts both sent and received.
Get New Pix
1. In standby mode, press the
navigation key to highlight
Get Pix & Flix.
Menu, use the left
Get It Now. Press
2. To get new pix press
Get New PIX. Press
New
Provider, you are connected to the internet. Follow the
on-screen prompts.
Take Pix
This menu launches the camera.
1. In standby mode, press the
Menu, use the left
Section 9: Multimedia
129
navigation key to highlight
Get It Now. Press
Get Pix & Flix.
2. Press
Take Pix. The camera is now active.
3. Press the right soft key Options, to choose the
specific camera settings. Use the right/left navigation
keys to advance to each setting category, and the up/
down navigation keys to make selections within each
category. The following categories are available:
• Picture Mode: Auto, Portrait, Scenic, Sports, Vivid and
Macro
• Flash: Auto, Off, On This Shot, Always On
• Self Timer: Off, 2 Sec, 5 Sec., 10 Sec.
• Multi-Shot Mode: Series Shot, Divided Shot
• Quality: Economy, Normal, Fine
• Resolution: (1600X1200), (1280X960), (1024X768),
(800X600), (640X480), (320X240), and Picture ID
Note: The larger the resolution setting, the longer it will take to display the
image.
• Brightness: 0 through -4 and 0 through 4
• White Balance: Auto, Sunny, Cloudy, Tungsten,
Fluorescent, and Manual
• Color Effect: Normal, Monochrome, Sepia, Warm, Cool,
Fog, Antique, Negative, Emboss, Sketch
• Metering: Average, Center, Spot
• Settings: Memory, Icon Display, Shutter Sound, Auto Focus
• Camcorder: Switches from Camera to Camcorder
130
Get V CAST Video
4. Press and hold
TAKE to capture a picture. Press the
right soft key Erase to delete it or press the left soft
key Save. The picture is now saved to the Gallery.
Pix Gallery
1. In standby mode, press the
Menu, use the left
navigation key to highlight
Get It Now. Press
Get Pix & Flix.
2. Press
Take Pix. The camera is now active.
3. Press the left soft key Gallery to review the pictures.
If the TransFlash is installed, a menu will be displayed
with the options, Phone and Card. Highlight the Phone
option and press the
key. The My Pix menu
displays with Default Album highlighted.
4. Press the right soft key Options to view your pictures
in a Slide Show, or to Lock the pictures from deletion.
Highlight your selection and press the
key. Press
Pause or the left soft key Done to return.
5. Press the left soft key New to create a new album.
Enter the New Name and press the
key.
6. From the My Pix menu, select
Card. This displays
any pictures you have taken and stored on the
TransFlash memory card. Press
right soft key Options to select from the following
options:
View. Press the
• Send: Launches the Create Pix/Flix Msg screen.
• To Pix Place: Transfers the file to the online gallery.
• Set As: Set the picture as the main wallpaper, front wallpaper,
Picture ID, Power On image, or Power Off image.
Section 9: Multimedia
131
• Rename: Allows you to rename the picture.
• Lock: Locks the picture to prevent deletion.
• Erase: Erases the selected picture from the gallery.
• Erase All: Erases all pictures from the gallery.
• Move: Moves the images from the card to the phone.
• Make Postcard: Adds text to a picture selected from the Pix
Gallery stored on the TransFlash card.
• Pix Info: Provides the date, time, location, resolution, size
and rights to the selected picture.
7. Use the navigation key to make your selection and press
.
Take Flix
This menu launches the camcorder.
1. In standby mode, press the
Menu, use the left
Get It Now. Press
navigation key to highlight
Get Pix & Flix.
2. Press
Take Flix. The camcorder is now active.
Press the right soft key Options to select from the
following options:
• Recording Mode: Limit for MMS, Normal, Rec. at Interv
• Flash: Auto, Off, On This Shot, Always On
• Self Timer: Off, 2 Sec, 5 Sec., 10 Sec.
• Quality: Economy, Normal, Fine
• Brightness: 0 through 4 and 0 through -4
• White Balance: Auto, Sunny, Cloudy, Tungsten, Florescent,
Manual
• Color Effect: Normal, Monochrome, Sepia, Warm, Cool,
Fog, Antique, Negative
• Settings: Memory, Frame Rate, Icon Display
132
Get V CAST Video
• Camera: Switches from camcorder to camera.
3. Press to save the settings.
4. Press REC to begin recording. Press the left soft key
Pause or STOP.
5. Press the right soft key Erase or the left soft key
Save.
Note: If you receive an incoming call while using your camcorder, the
video recording is stopped. You will be presented with the call ignore /
accept screen. If you ignore the call, then you are given the choice to
Save, Send or Erase the video. If you accept the call, then your video is
auto-saved and the camcorder application exits in the background.
Note: If the battery level becomes too low while you are recording, the
recording is stopped and the video is auto-saved. The low battery
indicator will be displayed and you will exit from the camcorder
application. If your battery is too low then the phone will power down
without saving the video.
Note: If you receive a text message, a multi-media message or a voice mail
while you are recording, the video recording is stopped. You are given the
choice to View Now or View Later. If you choose later, you are given the
chance to Save, Send or Erase the video. If you want to view the message
now, the video is auto-saved and the camera application exits in the
background.
Note: The zoom feature is disabled while recording a video. If zoom is
desired, be sure and set it before you start recording.
Section 9: Multimedia
133
My Pix
This menu allows you to review the pictures you have
takenordownloadedandstoredintoyourphoneand/or
TransFlash card.
1. In standby mode, press the
navigation key to highlight
Get Pix & Flix.
Menu, use the left
Get It Now. Press
2. Press
been stored on your phone or
have been stored on the TransFlash card. Press
3. If Phone is selected, the Default Album is highlighted.
Press to view the pix in thumbnail mode. Press
My Pix,
Phone to view pix that have
Card to view pix that
.
View to execute the selected picture.
4. Press the right soft key Options for the following
options. Highlight an option and press
selection.
to make your
• Send
• To Pix Place
• Set As
• Rename
• Lock
• Erase
• Erase All
• Move
• Make Postcard
• Pix Info
134
My Flix
My Flix
Thismenuallowsyoutoreviewthevideosyouhavetaken
or downloaded and stored into your phone and/or
TransFlash card.
1. In standby mode, press the
navigation key to highlight
Get Pix & Flix.
Menu, use the left
Get It Now. Press
2. Press
been stored on your phone or
have been stored on the TransFlash card. Press
3. If Phone is selected, the Default Album is highlighted.
Press to view the flix in thumbnail mode. Press
My Flix,
Phone to view flix that have
Card to view flix that
.
Play to execute the selected video.
4. Press the right soft key Options for the following
options. Highlight an option and press
selection.
to make your
• Send
• To Pix Place
• Set As
• Rename
• Lock
• Erase
• Erase All
• Move
• Flix Info
Section 9: Multimedia
135
Pix/Flix Place
Send a pix/flix message to your online album.
Note: You must first setup your account on the Verizon Wireless website:
www.verizonwireless.com before establishing a connection.
1. In standby mode, press
navigation key to highlight
Get Pix & Flix.
Menu, use the left
Get It Now. Press
2. Highlight Pix/Flix Place and press
. The Pix Place
sign-on screen displays.
3. Enter your Mobile Number and Password. Use the
navigation key to highlight LOGIN and press
. You
are now connected to your online album.
Get Fun & Games
Select from several fun and interesting applications or a
broadcategoryofgamesthatyoucanplayonyourphone.
1. In standby mode, press
navigation key to highlight
Get Fun & Games.
Menu, use the left
Get It Now. Press
2. Press
Get New.
3. Use the navigation keys to make a selection and press
.
4. Choose the charge Either Subscription or Unlimited, then
press
. Follow in screen prompts to apply.
Get News & Info
1. In standby mode, press
Menu, use the left
136
Get Going
navigation key to highlight
Get It Now. Press
Get News & Info.
2. The browser is launched and a pop up screen with
available applications is displayed.
3. Use the navigation key to browse the categories.
4. Once the desired category is highlighted, press
to
enter the category list.
WhenyouuseGetNews&Info,someofthekeysoperate
differently than during a normal phone call.
It presents on-screen items in any of the following ways:
• Text or numeric input
• Links (embedded in content)
• Numbered options (some options may not be numbered)
• Simple text
You can utilize the options or links by using the soft keys.
Get Going
Download applications that keep you in touch with the
world, keep you organized, and help you find the coolest
spots.
1. In standby mode, press the
navigation key to highlight
Get Going.
Menu, use the left
Get It Now. Press
2. Get New is highlighted. Press
.
3. Highlight the application you wish to download and press
.
Section 9: Multimedia
137
4. Highlight your selection and press
subscription prompts and press
process begins.
. Follow on screen
. The download
5. At the “App installed successfully. Would you like to run
it?” prompt, press Yes to launch application, or No to
return to category list.
Note: The GET GOING menu will display all downloaded applications, with
the most current download first.
How Keys Work
The following table lists keys and functions
Navigation Key: Use the navigation key to browse
lists and highlight options.
CLR Key: A browser back-up key. Press once to back
up one page. Press and hold to go back to home page.
Press to clear the last number, letter, or symbol
entered. Press and hold to completely clear the
display.
Asterisk/Shift Key: Press before entering text to
enable upper case characters (in Abc mode).
0/Next Key: Press to enter a zero (0), or to display
another word in the dictionary when in Word entry
mode.
Pound/Space Key: Press to insert a space when
entering text.
138
How Keys Work
Numbers: Use the number keys to select items in a
menu if they are numbered.1 - 9.
END Key: Press to exit VZW TODAY and return the
phone to standby mode.
Left Soft Key: Press the left soft key to go to the
highlighted web link and/or perform the function
above it in the display.
Right Soft Key: The right soft key is the Menu key.
Press this key to display a pop-up menu with
several options.
SEND Key: Press to dial a highlighted number
Section 9: Multimedia
139
140
Calendar
Scheduleuptoeighteventsforanydaybyindicatingeach
event’s start and end time. Set alarms for events so that
you can be alerted before an event takes place. Events
scheduled for future dates automatically appear on your
Today events schedule for the present day.
Add a new event
1. In standby mode, press the (
) Menu, then press the
right navigation key to
Settings & Tools. Press
Tools
Calendar. The calendar appears in the
display with the current date highlighted.
2. Press the right soft key ( ) Options. A pop-up menu
appears in the display that contains the menu items.
• Weekly: View the current week.
• Go To Date: Go to any date that you specify.
• Go to Today: View today’s events.
• Erase Old: Select a past event to delete.
• Erase All: Delete all events in your calendar
3. Press the left soft key ( ) Add to add a new event.
4. The Appointment name field is highlighted. Enter the
name and use the down navigation key to move to the
following fields:
• Start Date: Enter the start date for the event.
• Start Time: Enter the start time for the event.
• AM/PM: Select from A.M. or P.M. for the start time.
• End Date: Enter the end date for the event.
• End Time: Enter the end time for the event.
142
Calendar
• AM/PM: Select from A.M. or P.M for the end time.
• Time Zone: Enter the time zone you wish your event to
reflect.
• Recurrence: Select the frequency of the event.
• Alert: Turn the alarm for the event on or off.
• Reminder: Set a reminder up to one day before the event.
5. Fill in and select event details using the navigation keys
and the alpha-numeric keypad.
6. Press
. The event is saved.
View an event
1. In standby mode, press the
Menu, then press the
right navigation key to
Settings & Tools. Press
Tools
Calendar.
2. A calendar appears in the display with the current date
highlighted.
3. Use the navigation keys to highlight the date containing
the event that you wish to view. If the event date is in
another month, press the right soft key Options.
Tip: Use the volume key to move between months in the calendar.
4. In the pop-up menu that appears in the display, use the
navigation key to highlight Go To Date, then press
.
5. Enter the desired date in the box at the bottom of the
display, then press
appears in the display with the event date highlighted.
6. Press View event details for the date.
. The month that you entered
Section 10: Organizer
143
7. Press the right soft key Options. A pop-up menu
appears in the display.
8. To edit the event, press the left soft key Edit.
9. To save edits the selected event, press
SAVE.
10. To erase the current event, press right soft key
Options. A pop-up menu appears in the display.
11. Press
highlighted. Press the
navigation key to No to cancel.
Erase. A pop-up menu appears with Yes
key erase, or use the down
Alarm Clock
Your phone has an alarm clock that can be set to go off
once, or recur daily at a specific time. Once set, the alarm
clock is easy to change or turn off.
Set An Alarm
1. In standby mode, press the
Menu, then press the
right navigation key to
Settings & Tools. Press
Tools
Alarm Clock. The Alarm Clock menu displays
with the Alarm 1 highlighted.
2. The following options appear in the display
• Alarm 1
• Alarm 2
• Alarm 3
3. Use the navigation key to highlight the alarm that you
wish to enable, then press
. The Set Alarm (1, 2, or 3
depending on your selection) screen appears in the
display.
144
Alarm Clock
4. The Alarm field is highlighted. Use the left/right
navigation key to select On or Off.
5. Press the down navigation key to highlight the Time
field, then enter the time that you wish for the alarm to
sound.
6. Press the down navigation key once to highlight the AM/
PM field. Use the left/right navigation keys to select AM
or PM.
7. Press the down navigation key once to highlight the
Frequency field. Use the left/right navigation keys to set
the frequency (occurrence) of the alarm. Below lists and
defines the options for this field.
• Once: The alarm sounds only once, at the time specified.
• Daily: The alarm sounds every day at the time specified.
• Mon-Fri: The alarm sounds Monday through Friday at the
time specified.
• Weekends: The alarm sounds Saturday through Sunday at
the time specified.
8. Press the down navigation key once to highlight the
Ringer field. Use the left/right navigation keys to set the
alert tone.
9. When all fields have correct information entered, press
the
SAVE key to save your settings.
Disable an alarm before it sounds
1. In standby mode, press the (
) Menu, then press the
Settings & Tools. Press
Alarm Clock. The Alarm Clock menu displays
with the Alarm 1 highlighted.
right navigation key to
Tools
Section 10: Organizer
145
2. The following options appear in the display
• Alarm 1
• Alarm 2
• Alarm 3
3. The Alarm Clock menu displays with the Alarm 1
highlighted.
4. Use the navigation key to highlight the alarm you wish to
disable, then press the right soft key Options. A pop-
up menu appears in the display.
5. Press
to reset the highlighted alarm or press
to
reset all alarms.
Snooze
When an alarm sounds, a menu screen displays that
allowsyoutoeitherturnthealarmoffortohavethealarm
ring again after 5 minutes. This is called Snooze.
To use this feature follow these steps:
1. Set one of your phone’s 3 alarms. For more information
about setting an alarm, see "Set An Alarm" on page 144.
2. When an alarm sounds, use the up/down navigation key
to highlight Snooze or Dismiss. Press the left soft key
Snooze to turn the alarm off and to set it to ring again
after 5 minutes. Or, highlight Dismiss to turn the alarm
off completely. The alarm turns off and the standby
screen displays.
World Clock
World Clock allows you to view the time of day or night
in any part of the world.
146
Notepad
1. In standby mode, press the
Menu, then press the
Settings & Tools. Press
right navigation key to
Tools
World Clock.
2. Use the left soft key Cities to display the 45
supported cities. Press the
key to save your entry.
3. Press the right soft key Options to view the following
options:
• Set as Local Time: Sets the time according to the city
chosen in the Cities field.
• Daylight Savings Time: Sets the Daylight Savings time
option.
4. Press
to return to standby mode.
Notepad
CreateandstorenotesinNotepad.Youcan’tprioritizeor
setanalertforstorednotes.ReturntoMemoPadanytime
to review and edit your notes.
1. In standby mode, press the
Menu, then press the
right navigation key to
Settings & Tools. Press
Tools
Notepad. The Note Pad menu opens.
2. If you have any stored notes, they appear as a list in the
display. If this is your first time in Notepad, No Note
displays.
3. To add a new memo, press the left soft key Add, then
enter the memo using the keypad.
4. While entering a memo, press the left soft key Abc, to
display a pop-up menu with the following text entry
modes
Section 10: Organizer
147
• Word
• Abc
• ABC
• 123
• Symbols
5. Use the navigation keys to select the other available text
entry modes of 123, Word, and Symbol, or press
exit the pop-up menu.
to
6. When you’re finished entering details for the note, press
. The note is saved.
Review, Add, Edit, and Erase Memos
1. In standby mode, press the
Menu, then press the
right navigation key to
Settings & Tools. Press
Tools
Notepad. The Note Pad menu opens. If you
have any stored notes, they appear as a list in the
display.
2. With a memo highlighted, press the right soft key
Options. A pop-up menu with the options listed in the
following table appears in the display:
• Edit: Edit the note currently highlighted or appearing in the
display.
• Erase: Erase the note currently highlighted or appearing in the
display.
• Erase All: Erase all notes.
3. Use the navigation key to highlight an option or press
to exit the pop-up menu.
4. Press
to perform the highlighted option’s function.
148
Calculator
Calculator
You can perform calculations, including addition,
subtraction, multiplication and division using your
phone.
1. In standby mode, press the (
) Menu, then press the
right navigation key to
Settings & Tools. Press
Tools
Calculator. The Calculator opens.
2. Enter the first number in your equation using the keypad.
(Numbers can be up to nine digits long.)
3. Press the right soft key ( ) Operator to display a pop-up
menu which allows you to enter a Parenthesis or Power.
Press the left soft key ( ) Clear to clear all data entered.
4. Press
to change the sign for a number to a negative.
to add a decimal point.
5. Press the
6. Use the navigation key to set the type of calculation that
you wish to perform. Your choices are as follows.
• [+] Addition
• [-] Subtraction
• [x] Multiplication
• [÷] Division
7. Use the keypad to enter the second number into your
equation.
8. Press
to perform the calculation and view the
result.
Section 10: Organizer
149
File Viewer
The File Viewer menu displays the files you have stored
onyourphoneorcard.Youmayselectyourfilesfromthis
menu and the associated program will open the file.
Note: Files that are stored on the TransFlash memory card are stored in the
MY_FILES directory. Supported file types are BMP, PNG, ELX, PPT, DOC,
JPG, and PDF.
1. In standby mode, press the
Menu, then press the
right navigation key to
Settings & Tools. Press
Tools
Phone menu option highlighted.
2. Press the key to open files located on your Phone,
or press Card to open files on the your Card. A list
of available files displays.
File Viewer. The File Viewer opens with the
3. Press the
4. Press
key to view.
to return to standby mode.
MP3
The MP3 player can be used to play files you have loaded
from your PC to the TransFlash card.
Note: The following characters cannot be used in the filename:
/ \ * ? “ < > : |
The file name is limited to 60.3 characters (sixty to left of ‘.’, three to right
of ‘.’)
1. In standby mode, press the (
) Menu, then press the
right navigation key to
Settings & Tools. Press
150
MP3
Tools
MP3. The MP3 opens with the list of files
displayed.
Note: The MP3 option will display only if MP3 files are loaded in the
MY_MUSIC folder on the TransFlash memory card.
2. Press the right soft key Options, to select from the
following options:
• Select All: Marks all MP3 files for play.
• Rename: Prompts Enter New Name field to rename the MP3
file.
• Erase: Erases the selected file.
• Erase All: Erases all files.
• Song info: Displays title, artist, album title, genre, copyright,
time, size and bit rate information for the file.
3. Press the left soft key Play, to play the marked MP3
file.
Section 10: Organizer
151
152
Section 11: Mobile Web
Topics Covered
• Mobile Web
• Launching Mobile Web
• Exit Mobile Web
• Navigate the Web
• Mobile Web soft keys
• Links
• Place a call while using Mobile Web
This section describes how you can surf the web from
your wireless phone. For more information, contact
your service provider.
Section 11: Mobile Web
153
Mobile Web
Note: This feature is currently unavailable outside of the United States.
Only available within the Verizon Wireless Enhances Services Area.
Mobile Web allows you to surf the web from your
wireless phone.
Note: If you receive a call while using Mobile Web, the application is put on
hold during the call. Once the call ends, your Mobile Web session resumes
where you left off. Only available within the Verizon Wireless Enhances
Services Area
Note: Any time the service indicator icon is visible, you are connected to
the Internet and billed accordingly. Rates and prices vary according to your
service contract. For further information on billing contact Verizon Wireless.
Only available within the Verizon Wireless Enhances Services Area
Launch Mobile Web
Note: This feature is currently unavailable outside of the United States.
Only available within the Verizon Wireless Enhances Services Area.
1. In standby mode, press the up navigation key. Mobile
Web and a list of categories (representing one or more
web sites) appears in the display.
2. Use the navigation key to browse the categories.
3. Once the desired category is highlighted, press
to
enter the category list.
154
Exit Mobile Web
Exit Mobile Web
ThisfeatureiscurrentlyunavailableoutsideoftheUnited
States. Only available within the Verizon Wireless
Enhances Services Area.
Ⅵ Press
to exit Mobile Web.
Navigate the Web
Note: This feature is currently unavailable outside of the United States.
Only available within the Verizon Wireless Enhances Services Area.
When you use Mobile Web, some of the keys operate
differently than during a normal phone call.
Mobile Web presents on-screen items in any of the
following ways:
• Text or numeric input
• Links (embedded in content)
• Numbered options (some options may not be numbered)
• Simple text
You can act on the options or links by using the soft keys.
Mobile Web Soft Keys
Note: This feature is currently unavailable outside of the United States.
Only available within the Verizon Wireless Enhances Services Area.
At the bottom of the Mobile Web display contains the
browser commands. The left and right soft keys on
the keypad are used to perform the commands in the
Section 11: Mobile Web
155
display. These are called “soft keys” because their
function changes depending where you are in the
application.
How Mobile Web keys work
The following table lists Mobile Web keys and functions.
Navigation Key: Use the navigation key to browse
lists and highlight options.
CLR Key: A browser back-up key. Press once to back
up one page. Press and hold to go back to Mobile Web
home page.
Press to clear the last number, letter, or symbol
entered. Press and hold to completely clear the
display.
Asterisk/Shift Key: Press before entering text to
enable upper case characters (in Abc mode).
0/Next Key: Press to enter a zero (0), or to display
another word in the dictionary when in Word entry
mode.
Pound/Space Key: Press to insert a space when
entering text.
Numbers 1 - 9: Use the number keys to select items
in a menu if they are numbered.
END Key: Press to exit Mobile Web and return the
phone to standby mode.
Left Soft Key: Press the left soft key to go to the
highlighted web link and/or perform the function
above it in the display.
156
Links
Right Soft Key: The right soft key is the Menu key.
Press this key to display a pop-up menu with several
options.
SEND Key: Press to dial a highlighted number.
Links
Note: This feature is currently unavailable outside of the United States.
Only available within the Verizon Wireless Enhances Services Area.
Links can serve several purposes, such as jumping to a
differentpage,toadifferentsite,orinitiatingaphonecall.
Linksareshowninsideofbrackets([ ]).Normally,theleft
soft key is used to select a highlighted link.
Place a Call While Using Mobile Web
Note: This feature is currently unavailable outside of the United States.
Only available within the Verizon Wireless Enhances Services Area.
YoucanplaceacallwhileusingMobileWebifthewebsite
supportsthisfeature.Presstheappropriatesoftkeytocall
thenumber.Inmostcasesyoucanalsopress
tocallthe
number. The Internet connection terminates when you
initiatethecall.Afteryouendthecall,yourphonereturns
to standby mode.
Section 11: Mobile Web
157
158
Health and Safety Information
Exposure to Radio Frequency (RF) Signals
Certification Information (SAR)
Your wireless phone is a radio transmitter and receiver. It
isdesignedandmanufacturednottoexceedtheexposure
limits for radio frequency (RF) energy set by the Federal
Communications Commission (FCC) of the U.S.
government.TheseFCCexposurelimitsarederivedfrom
the recommendations of two expert organizations, the
National Counsel on Radiation Protection and
Measurement (NCRP) and the Institute of Electrical and
Electronics Engineers (IEEE). In both cases, the
recommendations were developed by scientific and
engineering experts drawn from industry, government,
and academia after extensive reviews of the scientific
literature related to the biological effects of RF energy.
The exposure limit set by the FCC for wireless mobile
phones employs a unit of measurement known as the
Specific Absorption Rate (SAR). The SAR is a measure of
the rate of absorption of RF energy by the human body
expressedinunitsofwattsperkilogram(W/kg).TheFCC
requires wireless phones to comply with a safety limit of
1.6 watts per kilogram (1.6 W/kg). The FCC exposure
limit incorporates a substantial margin of safety to give
additional protection to the public and to account for any
variations in measurements.
SAR tests are conducted using standard operating
positions accepted by the FCC with the phone
transmitting at its highest certified power level in all
testedfrequencybands. AlthoughtheSARisdetermined
160
Health and Safety Information
at the highest certified power level, the actual SAR level
of the phone while operating can be well below the
maximumvalue.Thisisbecausethephoneisdesignedto
operate at multiple power levels so as to use only the
power required to reach the network. In general, the
closeryouaretoawirelessbasestationantenna,thelower
the power output.
Before a new model phone is available for sale to the
public, it must be tested and certified to the FCC that it
does not exceed the exposure limit established by the
FCC. Tests for each model phone are performed in
positions and locations (e.g. at the ear and worn on the
body) as required by the FCC. Body-worn operations are
restricted to Samsung-supplied, approved, or non-
Samsung designated accessories that have no metal and
must provide at least 1.5 cm separation between the
device, including its antenna (whether extended or
retracted) and the user's body. Non-compliance with the
above restrictions may result in violation of FCC RF
exposure guidelines.
The FCC has granted an Equipment Authorization for
thismobile phonewithallreportedSAR levels evaluated
as in compliance with the FCC RF exposure guidelines.
The maximum SAR values for this model phone as
reported to the FCC are:
• Head:1.45 W/Kg.
• Body-worn: 1.03 W/Kg.
SAR information on this and other model phones can be
viewed on-line at www.fcc.gov/oet/fccid. To find
information that pertains to a particular model phone,
Section 12: Health and Safety Information
161
this site uses the phone FCC ID number which is usually
printed somewhere on the case of the phone. Sometimes
it may benecessary toremove the battery pack to find the
number. Once you have the FCC ID number for a
particular phone, follow the instructions on the website
anditshouldprovidevaluesfortypicalormaximumSAR
for a particular phone. Additional product specific SAR
information can also be obtained at www.fcc.gov/cgb/
sar.
Consumer Information on Wireless Phones
The U.S. Food and Drug Administration (FDA) has
published a series of Questions and Answers for
consumers relating to radio frequency (RF) exposure
from wireless phones. The FDA publication includes the
following information:
What kinds of phones are the subject of this update?
Thetermwirelessphonerefersheretohand-heldwireless
phones with built-in antennas, often called "cell,"
"mobile," or "PCS" phones. These types of wireless
phones can expose the user to measurable radio
frequency energy (RF) because of the short distance
between the phone and the user's head. These RF
exposures are limited by Federal Communications
Commission safety guidelines that were developed with
the advice of FDA and other federal health and safety
agencies. When the phone is located at greater distances
from the user, the exposure to RF is drastically lower
because a person's RF exposure decreases rapidly with
increasing distance from the source. The so-called
"cordless phones," which have a base unit connected to
162
Consumer Information on Wireless Phones
the telephone wiring in a house, typically operate at far
lowerpower levels, andthusproduceRFexposureswell
within the FCC's compliance limits.
Do wireless phones pose a health hazard?
The available scientific evidence does not show that any
health problems are associated with using wireless
phones. Thereisnoproof, however, that wireless phones
are absolutely safe. Wireless phones emit low levels of
radio frequency energy (RF) in the microwave range
while being used. They also emit very low levels of RF
wheninthestand-bymode.WhereashighlevelsofRFcan
producehealtheffects(byheatingtissue),exposuretolow
level RF that does not produce heating effects causes no
known adverse health effects. Many studies of low level
RFexposureshavenotfoundanybiologicaleffects.Some
studies have suggested that some biological effects may
occur, but such findings have not been confirmed by
additionalresearch.Insomecases,otherresearchershave
had difficulty in reproducing those studies, or in
determining the reasons for inconsistent results.
What is FDA's role concerning the safety of wireless
phones?
Under the law, FDA does not review the safety of
radiation-emitting consumer products such as wireless
phones before they can be sold, as it does with new drugs
ormedicaldevices. However, theagencyhasauthorityto
take action if wireless phones are shown to emit radio
frequency energy (RF) at a level that is hazardous to the
user. Insuchacase,FDAcouldrequirethemanufacturers
ofwirelessphonestonotifyusersofthehealthhazardand
Section 12: Health and Safety Information
163
torepair,replaceorrecallthephonessothatthehazardno
longer exists.
Although the existing scientific data do not justify FDA
regulatory actions, FDA has urged the wireless phone
industry to take a number of steps, including the
following:
• Support needed research into possible biological effects of RF
of the type emitted by wireless phones;
• Design wireless phones in a way that minimizes any RF
exposure to the user that is not necessary for device function;
and
• Cooperate in providing users of wireless phones with the best
possible information on possible effects of wireless phone use
on human health.
FDA belongs to an interagency working group of the
federal agencies that have responsibility for different
aspects of RF safety to ensure coordinated efforts at the
federal level. The following agencies belong to this
working group:
• National Institute for Occupational Safety and Health
• Environmental Protection Agency
• Federal Communications Commission
• Occupational Safety and Health Administration
• National Telecommunications and Information Administration
The National Institutes of Health participates in some
interagency working group activities, as well.
FDA shares regulatory responsibilities for wireless
phones with the Federal Communications Commission
(FCC). All phones that are sold in the United States must
164
Consumer Information on Wireless Phones
comply with FCC safety guidelines that limit RF
exposure. FCC relies on FDA and other health agencies
for safety questions about wireless phones.
FCC also regulates the base stations that the wireless
phone networks rely upon. While these base stations
operate at higher power than do the wireless phones
themselves, the RF exposures that people get from these
basestations are typicallythousands oftimes lower than
thosetheycangetfromwirelessphones. Basestationsare
thus not the primary subject of the safety questions
discussed in this document.
What are the results of the research done already?
The research done thus far has produced conflicting
results, and many studies have suffered from flaws in
their research methods. Animal experiments
investigating the effects of radio frequency energy (RF)
exposures characteristic of wireless phones have yielded
conflicting results that often cannot be repeated in other
laboratories. A few animal studies, however, have
suggested that low levels of RF could accelerate the
development of cancer in laboratory animals. However,
many of the studies that showed increased tumor
development used animals that had been genetically
engineeredortreatedwithcancer-causingchemicalssoas
to be pre-disposed to develop cancer in absence of RF
exposure. Other studiesexposed theanimals toRF for up
to22hoursperday.Theseconditionsarenotsimilartothe
conditions under which people use wireless phones, so
we don't know with certainty what the results of such
studies mean for human health.
Section 12: Health and Safety Information
165
Three large epidemiology studies have been published
since December 2000. Between them, the studies
investigated any possible association between the use of
wireless phones and primary brain cancer, glioma,
meningioma, oracousticneuroma, tumorsofthebrainor
salivary gland, leukemia, or other cancers. None of the
studiesdemonstratedtheexistenceofanyharmfulhealth
effects from wireless phones RF exposures. However,
noneofthestudiescananswerquestionsaboutlong-term
exposures, since the average period of phone use in these
studies was around three years.
What research is needed to decide whether RF exposure
from wireless phones poses a health risk?
Acombinationoflaboratorystudiesandepidemiological
studies of people actually using wireless phones would
providesomeofthedatathatareneeded.Lifetimeanimal
exposure studies could be completed in a few years.
However, very large numbers of animals would be
needed to provide reliable proof of a cancer promoting
effect if one exists. Epidemiological studies can provide
datathatisdirectlyapplicabletohumanpopulations,but
ten or more years' follow-up may be needed to provide
answers about some health effects, such as cancer. This is
because the interval between the time of exposure to a
cancer-causing agent and the time tumors develop - if
they do - may be many, many years. The interpretation of
epidemiological studies is hampered by difficulties in
measuring actual RF exposure during day-to-day use of
wireless phones. Many factors affect this measurement,
such as the angle at which the phone is held, or which
model of phone is used.
166
Consumer Information on Wireless Phones
What is FDA doing to find out more about the possible
health effects of wireless phone RF?
FDA is working with the U.S. National Toxicology
Program and with groups of investigators around the
world to ensure that high priority animal studies are
conducted to address important questions about the
effects of exposure to radio frequency energy (RF).
FDA has been a leading participant in the World Health
OrganizationinternationalElectromagneticFields(EMF)
Project since its inception in 1996. An influential result of
this work has been the development of a detailed agenda
ofresearchneedsthathasdriventheestablishmentofnew
researchprogramsaroundtheworld.TheProjecthasalso
helpeddevelopaseriesofpublicinformationdocuments
on EMF issues.
FDA and Cellular Telecommunications & Internet
Association (CTIA) have a formal Cooperative Research
andDevelopmentAgreement(CRADA)todoresearchon
wireless phone safety. FDA provides the scientific
oversight, obtaining input from experts in government,
industry, and academic organizations. CTIA-funded
research is conducted through contracts to independent
investigators. The initial research will include both
laboratory studies and studies of wireless phone users.
The CRADA will also include a broad assessment of
additional research needs in the context of the latest
research developments around the world.
Section 12: Health and Safety Information
167
What steps can I take to reduce my exposure to radio
frequency energy from my wireless phone?
If there is a risk from these products - and at this point we
do not know that there is - it is probably very small. But if
you are concerned about avoiding even potential risks,
you can take a few simple steps to minimize your
exposure to radio frequency energy (RF). Since time is a
key factor in how much exposure a person receives,
reducingtheamountoftimespentusingawirelessphone
will reduce RF exposure.
• If you must conduct extended conversations by wireless phone
every day, you could place more distance between your body
and the source of the RF, since the exposure level drops off
dramatically with distance. For example, you could use a
headset and carry the wireless phone away from your body or
use a wireless phone connected to a remote antenna.
Again,thescientificdatadonotdemonstratethatwireless
phonesareharmful.ButifyouareconcernedabouttheRF
exposure from these products, you can use measures like
those described above to reduce your RF exposure from
wireless phone use.
What about children using wireless phones?
Thescientificevidencedoesnotshowadangertousersof
wirelessphones,includingchildrenandteenagers.Ifyou
want to take steps to lower exposure to radio frequency
energy (RF), the measures described above would apply
to children and teenagers using wireless phones.
Reducing the time of wireless phone use and increasing
the distance between the user and the RF source will
reduce RF exposure.
168
Consumer Information on Wireless Phones
Some groups sponsored by other national governments
have advised that children be discouraged from using
wireless phones at all. For example, the government in
theUnitedKingdomdistributedleafletscontainingsuch
arecommendationinDecember2000.Theynotedthatno
evidence exists that using a wireless phone causes brain
tumorsorotherilleffects.Theirrecommendationtolimit
wireless phone use by children was strictly
precautionary;itwasnotbasedonscientificevidencethat
any health hazard exists.
Do hands-free kits for wireless phones reduce
risks from exposure to RF emissions?
Since there are no known risks from exposure to RF
emissions from wireless phones, there is no reason to
believe that hands-free kits reduce risks. Hands-free kits
can be used with wireless phones for convenience and
comfort. These systems reduce the absorption of RF
energyintheheadbecausethephone, whichisthesource
of the RF emissions, will not be placed against the head.
On the other hand, if the phone is mounted against the
waist or other part of the body during use, then that part
of the body will absorb more RF energy. Wireless phones
marketed in the U.S. are required to meet safety
requirementsregardlessofwhethertheyareusedagainst
the head or against the body. Either configuration should
result in compliance with the safety limit.
Do wireless phone accessories that claim to shield
the head from RF radiation work?
Since there are no known risks from exposure to RF
emissions from wireless phones, there is no reason to
Section 12: Health and Safety Information
169
believethataccessories that claim toshieldtheheadfrom
thoseemissionsreducerisks.Someproductsthatclaimto
shield the user from RF absorption use special phone
cases, while others involve nothing more than a metallic
accessoryattachedtothephone.Studieshaveshownthat
these products generally do not work as advertised.
Unlike "hand-free" kits, these so-called "shields" may
interfere with proper operation of the phone. The phone
may be forced to boost its power to compensate, leading
to an increase in RF absorption. In February 2002, the
FederaltradeCommission(FTC)chargedtwocompanies
that sold devices that claimed to protect wireless phone
users from radiation with making false and
unsubstantiated claims. According to FTC, these
defendantslackedareasonablebasistosubstantiatetheir
claim.
What about wireless phone interference with
medical equipment?
Radio frequency energy (RF) from wireless phones can
interact with some electronic devices. For this reason,
FDA helped develop a detailed test method to measure
electromagnetic interference (EMI) of implanted cardiac
pacemakers and defibrillators from wireless telephones.
This test method is now part of a standard sponsored by
the Association for the Advancement of Medical
instrumentation (AAMI). The final draft, a joint effort by
FDA, medical device manufacturers, and many other
groups, was completed in late 2000. This standard will
allow manufacturers to ensure that cardiac pacemakers
anddefibrillatorsaresafefromwirelessphoneEMI. FDA
has tested wireless phones and helped develop a
170
Consumer Information on Wireless Phones
voluntary standard sponsored by the Institute of
ElectricalandElectronicEngineers(IEEE).Thisstandard
specifiestestmethodsandperformancerequirementsfor
hearing aids and wireless phones so that no interference
occurs when a person uses a compatible phone and a
compatible hearing aid at the same time. This standard
was approved by the IEEE in 2000.
FDA continues to monitor the use of wireless phones for
possible interactions with other medical devices. Should
harmfulinterferencebefoundtooccur,FDAwillconduct
testing to assess the interference and work to resolve the
problem.
Additional information on the safety of RF exposures
from various sources can be obtained from the following
organizations:
• FCC RF Safety Program:
http://www.fcc.gov/oet/rfsafety/
• Environmental Protection Agency (EPA):
http://www.epa.gov/radiation/
• Occupational Safety and health Administration's (OSHA):
http://www.osha.gov/SLTC/radiofrequencyradiation/
index.html
• National institute for Occupational Safety and health (NIOSH):
http://www.cdc.gov/niosh/topics/emf/
• World health Organization (WHO):
http://www.who.int/peh-emf/
• International Commission on Non-Ionizing Radiation Protection:
http://www.icnirp.de
• National Radiation Protection Board (UK):
http://www.hpa.org.uk/radiation/
Section 12: Health and Safety Information
171
• Updated 7/16/2003: US food and Drug Administration
http://www.fda.gov/cellphones
Road Safety
Your wireless phone gives you the powerful ability to
communicatebyvoice,almostanywhere,anytime.Butan
important responsibility accompanies the benefits of
wireless phones, one that every user must uphold.
When driving a car, driving is your first responsibility.
When using your wireless phone behind the wheel of a
car, practice good common sense and remember the
following tips:
1. Get to know your wireless phone and its features, such
as speed dial and redial. If available, these features help
you to place your call without taking your attention off
the road.
2. When available, use a hands-free device. If possible, add
an additional layer of convenience and safety to your
wireless phone with one of the many hands free
accessories available today.
3. Position your wireless phone within easy reach. Be able
to access your wireless phone without removing your
eyes from the road. If you get an incoming call at an
inconvenient time, let your voicemail answer it for you.
4. Let the person you are speaking with know you are
driving; if necessary, suspend the call in heavy traffic or
hazardous weather conditions. Rain, sleet, snow, ice and
even heavy traffic can be hazardous.
172
Road Safety
5. Do not take notes or look up phone numbers while
driving. Jotting down a "to do" list or flipping through
your address book takes attention away from your
primary responsibility, driving safely.
6. Dial sensibly and assess the traffic; if possible, place
calls when you are not moving or before pulling into
traffic. Try to plan calls when your car will be stationary.
If you need to make a call while moving, dial only a few
numbers, check the road and your mirrors, then
continue.
7. Do not engage in stressful or emotional conversations
that may be distracting. Make people you are talking
with aware you are driving and suspend conversations
that have the potential to divert your attention from the
road.
8. Use your wireless phone to call for help. Dial 9-1-1 or
other local emergency number in the case of fire, traffic
accident or medical emergencies. Remember, it is a free
call on your wireless phone!
9. Use your wireless phone to help others in emergencies. If
you see an auto accident, crime in progress or other
serious emergency where lives are in danger, call 9-1-1
or other local emergency number, as you would want
others to do for you.
Section 12: Health and Safety Information
173
10. Call roadside assistance or a special non-emergency
wireless assistance number when necessary. If you see
a broken-down vehicle posing no serious hazard, a
broken traffic signal, a minor traffic accident where no
one appears injured, or a vehicle you know to be stolen,
call roadside assistance or other special non-emergency
number.
"The wireless industry reminds you to use your phone safely
when driving."
Formoreinformation,pleasecall1-888-901-SAFE,orvisit
our web-site www.wow-com.com
Provided by theCellularTelecommunications& Internet
Association
Operating Environment
Remember to follow any special regulations in force in
anyareaandalwaysswitchyourphoneoffwheneveritis
forbidden to use it, or when it may cause interference or
danger. When connecting the phone or any accessory to
another device, read its user's guide for detailed safety
instructions. Do not connect incompatible products.
Aswithothermobileradiotransmittingequipment,users
are advised that for the satisfactory operation of the
equipment and for the safety of personnel, it is
recommendedthattheequipmentshouldonlybeusedin
the normal operating position (held to your ear with the
antenna pointing over your shoulder).
174
Using Your Phone Near Other Electronic Devices
UsingYourPhoneNearOtherElectronicDevices
Most modern electronic equipment is shielded from
radiofrequency(RF)signals.However,certainelectronic
equipment may not be shielded against the RF signals
from your wireless phone. Consult the manufacturer to
discuss alternatives.
Pacemakers
Pacemaker manufacturers recommend that a minimum
distance of 15 cm (6 inches) be maintained between a
wireless phone and a pacemaker to avoid potential
interference with the pacemaker.
These recommendations are consistent with the
independent research and recommendations of Wireless
Technology Research.
Persons with pacemakers:
• should always keep the phone more than 15 cm (6 inches) from
their pacemaker when the phone is switched on.
• should not carry the phone in a breast pocket.
• should use the ear opposite the pacemaker to minimize
potential interference.
If you have any reason to suspect that interference is
taking place, switch your phone off immediately.
Hearing Aids
Some digital wireless phones may interfere with some
hearing aids. In the event of such interference, you may
wish to consult your hearing aid manufacturer to discuss
alternatives.
Section 12: Health and Safety Information
175
Other Medical Devices
Ifyouuseanyotherpersonalmedicaldevices,consultthe
manufacturer of your device to determine if it is
adequately shielded from external RF energy. Your
physician may be able to assist you in obtaining this
information.Switchyourphoneoffinhealthcarefacilities
whenanyregulationspostedintheseareasinstructyouto
do so. Hospitals or health care facilities may be using
equipment that could be sensitive to external RF energy.
Vehicles
RF signals may affect improperly installed or
inadequately shielded electronic systems in motor
vehicles. Check with the manufacturer or its
representative regarding your vehicle. You should also
consultthemanufacturerofanyequipmentthathasbeen
added to your vehicle.
Posted Facilities
Switchyourphoneoffinanyfacilitywherepostednotices
require you to do so.
Potentially Explosive Environments
Switchyourphoneoffwheninanyareawithapotentially
explosiveatmosphereandobeyallsignsandinstructions.
Sparks in such areas could cause an explosion or fire
resulting in bodily injury or even death.
Users are advised to switch the phone off while at a
refueling point (service station). Users are reminded of
the need to observe restrictions on the use of radio
equipment in fuel depots
176
Emergency Calls
(fuel storage and distribution areas), chemical plants or
where blasting operations are in progress.
Areas with a potentially explosive atmosphere are often
butnot always clearly marked. They includebelow deck
on boats, chemical transfer or storage facilities, vehicles
using liquefied petroleum gas (such as propane or
butane), areas where the air contains chemicals or
particles, such as grain, dust or metal powders, and any
other area where you would normally be advised to turn
off your vehicle engine.
Emergency Calls
Thisphone,likeanywirelessphone, operatesusingradio
signals, wireless and landline networks as well as user-
programmed functions, which cannot guarantee
connectioninallconditions. Therefore, youshouldnever
rely solely on any wireless phone for essential
communications (medical emergencies, for example).
Remember,tomakeorreceiveanycallsthephonemustbe
switched on and in a service area with adequate signal
strength. Emergency calls may not be possible on all
wireless phone networks or when certain network
services and/or phone features are in use. Check with
local service providers.
To make an emergency call:
1. If the phone is not on, switch it on.
2. Key in the emergency number for your present location
(for example, 911 or other official emergency number).
Emergency numbers vary by location.
3. Press Emergency number.
Section 12: Health and Safety Information
177
If certain features are in use (call barring, for example),
youmayfirstneedtodeactivatethosefeaturesbeforeyou
can make an emergency call. Consult this document and
your local cellular service provider.
Whenmakinganemergencycall,remembertogiveallthe
necessary information as accurately as possible.
Remember that your phone may be the only means of
communication at the scene of an accident; do not cut off
the call until given permission to do so.
Restricting Children's access to your Phone
Your phone is not a toy. Children should not be allowed
to play with it because they could hurt themselves and
others,damagethephoneormakecallsthatincreaseyour
phone bill.
FCC Notice and Cautions
FCC Notice
The phone may cause TV or radio interference if used in
close proximity to receiving equipment. The FCC can
require you to stop using the phone if such interference
cannot be eliminated.
Vehicles using liquefied petroleum gas (such as propane
orbutane)mustcomplywiththeNationalFireProtection
Standard (NFPA-58). For a copy of this standard, contact
the National Fire Protection Association, One
Batterymarch Park, Quincy, MA 02269, Attn: Publication
Sales Division.
178
Other Important Safety Information
Cautions
Any changes or modifications to your phone not
expressly approved in this document could void your
warranty for this equipment, and void your authority to
operate this equipment. Only use approved batteries,
antennas and chargers. The use of any unauthorized
accessories may be dangerous and void the phone
warranty if said accessories cause damage or a defect to
the phone.
Althoughyourphoneisquitesturdy, itisacomplexpiece
ofequipmentandcanbebroken.Avoiddropping,hitting,
bending or sitting on it.
Other Important Safety Information
• Only qualified personnel should service the phone or install the
phone in a vehicle. Faulty installation or service may be
dangerous and may invalidate any warranty applicable to the
device.
• Check regularly that all wireless phone equipment in your
vehicle is mounted and operating properly.
• Do not store or carry flammable liquids, gases or explosive
materials in the same compartment as the phone, its parts or
accessories.
• For vehicles equipped with an air bag, remember that an air bag
inflates with great force. Do not place objects, including both
installed or portable wireless equipment in the area over the air
bag or in the air bag deployment area. If wireless equipment is
improperly installed and the air bag inflates, serious injury
could result.
• Switch your phone off before boarding an aircraft. The use of
wireless phone in aircraft is illegal and may be dangerous to
the aircraft's operation.
Section 12: Health and Safety Information
179
• Failure to observe these instructions may lead to the
suspension or denial of telephone services to the offender, or
legal action, or both.
Product Performance
Getting the Most Out of Your Signal Reception
The quality of each call you make or receive depends on
the signal strength in your area. Your phone informs you
of the current signal strength by displaying a number of
bars next to the signal strength icon. The more bars
displayed, the stronger the signal.
Ifyou'reinsideabuilding, beingnearawindowmaygive
you better reception.
Understanding the Power Save Feature
If your phone is unableto finda signal after 15 minutes of
searching, a Power Save feature is automatically
activated. If your phone is active, it periodically rechecks
service availability or you can check it yourself by
pressing any key.
Anytime the Power Save feature is activated, a message
displays on the screen. When a signal is found, your
phone returns to standby mode.
Understanding How Your Phone Operates
Your phone is basically a radio transmitter and receiver.
When it's turned on, it receives and transmits radio
frequency (RF) signals. When you use your phone, the
system handling your call controls the power level. This
power can range from 0.006 watts to 0.2 watts in digital
mode.
180
Availability of Various Features/Ring Tones
Maintaining Your Phone's Peak Performance
For the best care of your phone, only authorized
personnel should service your phone and accessories.
Faulty service may void the warranty.
There are several simple guidelines to operating your
phone properly and maintaining safe, satisfactory
service.
• Hold the phone with the antenna raised, fully-extended and over
your shoulder.
• Try not to hold, bend or twist the phone's antenna.
• Don't use the phone if the antenna is damaged.
• Speak directly into the phone's receiver.
• Avoid exposing your phone and accessories to rain or liquid
spills. If your phone does get wet, immediately turn the power
off and remove the battery. If it is inoperable, call Customer
Care for service.
Availability of Various Features/Ring Tones
Many services and features are network dependent and
may require additional subscription and/or usage
charges. Not all features are available for purchase or use
inallareas.DownloadableRingTonesmaybeavailableat
an additional cost. Other conditionsandrestrictions may
apply. See your service provider for additional
information.
Section 12: Health and Safety Information
181
Battery Standby and Talk Time
Standby and talk times will vary depending on phone
usage patterns and conditions. Battery power
consumption depends on factors such as network
configuration, signal strength, operating temperature,
features selected, frequency of calls, and voice, data, and
other application usage patterns.
Battery Precautions
• Never use any charger or battery that is damaged in any way.
• Use the battery only for its intended purpose.
• If you use the phone near the network's base station, it uses
less power; talk and standby time are greatly affected by the
signal strength on the cellular network and the parameters set
by the network operator.
• Battery charging time depends on the remaining battery charge
and the type of battery and charger used. The battery can be
charged and discharged hundreds of times, but it will gradually
wear out. When the operation time (talk time and standby time)
is noticeably shorter than normal, it is time to buy a new
battery.
• If left unused, a fully charged battery will discharge itself over
time.
• Use only Samsung-approved batteries and recharge your
battery only with Samsung-approved chargers. When a charger
is not in use, disconnect it from the power source. Do not leave
the battery connected to a charger for more than a week, since
overcharging may shorten its life.
• Extreme temperatures will affect the charging capacity of your
battery: it may require cooling or warming first.
• Do not leave the battery in hot or cold places, such as in a car in
summer or winter conditions, as you will reduce the capacity
182
Care and Maintenance
and lifetime of the battery. Always try to keep the battery at
room temperature. A phone with a hot or cold battery may
temporarily not work, even when the battery is fully charged.
Li-ion batteries are particularly affected by temperatures
below 0 °C (32 °F).
• Do not short-circuit the battery. Accidental short-circuiting can
occur when a metallic object (coin, clip or pen) causes a direct
connection between the + and - terminals of the battery (metal
strips on the battery), for example when you carry a spare
battery in a pocket or bag. Short-circuiting the terminals may
damage the battery or the object causing the short-circuiting.
• Dispose of used batteries in accordance with local regulations.
In some areas, the disposal of batteries in household or
business trash may be prohibited. For safe disposal options for
Li-Ion batteries, contact your nearest Samsung authorized
service center. Always recycle. Do not dispose of batteries in a
fire.
Care and Maintenance
Your phone is a product of superior design and
craftsmanship and should be treated with care. The
suggestions below will help you fulfill any warranty
obligations and allow you to enjoy this product for many
years
• Keep the phone and all its parts and accessories out of the
reach of small children.
• Keep the phone dry. Precipitation, humidity and liquids contain
minerals that will corrode electronic circuits.
• Do not use the phone with a wet hand. Doing so may cause an
electric shock to you or damage to the phone.
• Do not use or store the phone in dusty, dirty areas, as its
moving parts may be damaged.
Section 12: Health and Safety Information
183
• Do not store the phone in hot areas. High temperatures can
shorten the life of electronic devices, damage batteries, and
warp or melt certain plastics.
• Do not store the phone in cold areas. When the phone warms
up to its normal operating temperature, moisture can form
inside the phone, which may damage the phone's electronic
circuit boards.
• Do not drop, knock or shake the phone. Rough handling can
break internal circuit boards.
• Do not use harsh chemicals, cleaning solvents or strong
detergents to clean the phone. Wipe it with a soft cloth slightly
dampened in a mild soap-and-water solution.
• Do not paint the phone. Paint can clog the device's moving
parts and prevent proper operation.
• Do not put the phone in or on heating devices, such as a
microwave oven, a stove or a radiator. The phone may explode
when overheated.
• Use only the supplied or an approved replacement antenna.
Unauthorized antennas or modified accessories may damage
the phone and violate regulations governing radio devices.
• If the phone, battery, charger or any accessory is not working
properly, take it to your nearest qualified service facility. The
personnel there will assist you, and if necessary, arrange for
service.
184
Standard Limited Warranty
What is Covered and For How Long? SAMSUNG
TELECOMMUNICATIONS AMERICA, L.P.
("SAMSUNG") warrants to the original purchaser
("Purchaser") that SAMSUNG's Phones and accessories
("Products") are free from defects in material and
workmanship under normal use and service for the
period commencing upon the date of purchase and
continuingforthefollowingspecifiedperiodoftimeafter
that date:
Phone
1 Year
Batteries
1 Year
Leather Case/ Pouch
Holster
90 Days
90 Days
Other Phone Accessories 1 Year
WhatisNotCovered?ThisLimitedWarrantyisconditioned
upon proper use of Product by Purchaser. This Limited
Warranty does not cover: (a) defects or damage resulting
from accident, misuse, abuse, neglect, unusual physical,
electrical or electromechanical stress, or modification of
any part of Product, including antenna, or cosmetic
damage; (b) equipment that has the serial number
removedormadeillegible;(c)anyplasticsurfacesorother
externally exposed parts that are scratched or damaged
duetonormaluse;(d)malfunctionsresultingfromtheuse
of Product in conjunction with accessories, products, or
186
Standard Limited Warranty
ancillary/peripheral equipment not furnished or
approved by SAMSUNG; (e) defects or damage from
impropertesting,operation,maintenance,installation,or
adjustment; (f) installation, maintenance, and service of
Product, or (g) Product used or purchased outside the
United States or Canada. This Limited Warranty covers
batteries only if battery capacity falls below 80% of rated
capacity or the battery leaks, and this Limited Warranty
does not cover any battery if (i) the battery has been
chargedbyabatterychargernotspecifiedorapprovedby
SAMSUNG for charging the battery, (ii) any of the seals
onthebatteryarebrokenorshowevidenceoftampering,
or (iii)thebattery has been used in equipmentotherthan
the SAMSUNG phone for which it is specified.
What are SAMSUNG's Obligations? During the applicable
warranty period, SAMSUNG will repair or replace, at
SAMSUNG's sole option, without charge to Purchaser,
any defective component part of Product. To obtain
service under this Limited Warranty, Purchaser must
return Product to an authorized phone service facility in
an adequate container for shipping, accompanied by
Purchaser's sales receipt or comparable substitute proof
ofsaleshowingthedateofpurchase, theserialnumber of
Product and the sellers' name and address. To obtain
assistance on where to deliver the Product, call Samsung
Customer Care at 1-888-987-4357. Upon receipt,
SAMSUNG will promptly repair or replace the defective
Product. SAMSUNG may, at SAMSUNG's sole option,
use rebuilt, reconditioned, or new parts or components
when repairing any Product or replace Product with a
rebuilt, reconditioned or new Product. Repaired/
replaced leather cases, pouches and holsters will be
Section 13: Warranty Information
187
warranted for a period of ninety (90) days. All other
repaired/replacedProductwillbewarrantedforaperiod
equal to the remainder of the original Limited Warranty
ontheoriginalProductorfor90days,whicheverislonger.
All replaced parts, components, boards and equipment
shall become the property of SAMSUNG. If SAMSUNG
determines that any Product is not covered by this
Limited Warranty, Purchaser must pay all parts,
shipping,andlaborchargesfortherepairorreturnofsuch
Product.
WHAT ARE THE LIMITS ON SAMSUNG'S WARRANTY/LIABILITY?
EXCEPTASSETFORTHINTHEEXPRESSWARRANTY
CONTAINED HEREIN, PURCHASER TAKES THE
PRODUCT "AS IS," AND SAMSUNG MAKES NO
WARRANTY OR REPRESENTATION AND THERE
ARE NO CONDITIONS, EXPRESS OR IMPLIED,
STATUTORY OR OTHERWISE, OF ANY KIND
WHATSOEVER WITH RESPECT TO THE PRODUCT,
INCLUDING BUT NOT LIMITED TO:
• THE MERCHANTABILITY OF THE PRODUCT OR ITS FITNESS FOR
ANY PARTICULAR PURPOSE OR USE;
• WARRANTIES OF TITLE OR NON-INFRINGEMENT;
• DESIGN, CONDITION, QUALITY, OR PERFORMANCE OF THE
PRODUCT;
• THE WORKMANSHIP OF THE PRODUCT OR THE COMPONENTS
CONTAINED THEREIN; OR
• COMPLIANCE OF THE PRODUCT WITH THE REQUIREMENTS OF
ANY LAW, RULE, SPECIFICATION OR CONTRACT PERTAINING
THERETO.
NOTHING CONTAINED IN THE INSTRUCTION
MANUAL SHALL BE CONSTRUED TO CREATE AN
188
Standard Limited Warranty
EXPRESS WARRANTY OF ANY KIND WHATSOEVER
WITH RESPECT TO THE PRODUCT. ALL IMPLIED
WARRANTIES AND CONDITIONS THAT MAY ARISE
BY OPERATION OF LAW, INCLUDING IF
APPLICABLE THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, ARE HEREBY LIMITED TO
THE SAME DURATION OF TIME AS THE EXPRESS
WRITTEN WARRANTY STATED HEREIN. SOME
STATES/PROVINCES DO NOT ALLOW
LIMITATIONS ON HOW LONG AN IMPLIED
WARRANTY LASTS, SO THE ABOVE LIMITATION
MAYNOTAPPLYTOYOU.INADDITION,SAMSUNG
SHALLNOTBELIABLEFORANYDAMAGESOFANY
KIND
RESULTING FROM THE PURCHASE, USE, OR
MISUSEOF,ORINABILITYTOUSETHEPRODUCTOR
ARISINGDIRECTLYORINDIRECTLYFROMTHEUSE
OR LOSS OF USE OF THE PRODUCT OR FROM THE
BREACHOFTHEEXPRESSWARRANTY,INCLUDING
INCIDENTAL, SPECIAL, CONSEQUENTIAL OR
SIMILAR DAMAGES, OR LOSS OF ANTICIPATED
PROFITS OR BENEFITS, OR FOR DAMAGES ARISING
FROM ANY TORT (INCLUDING NEGLIGENCE OR
GROSS NEGLIGENCE) OR FAULT COMMITTED BY
SAMSUNG, ITS AGENTS OR EMPLOYEES, OR FOR
ANY BREACH OF CONTRACT OR FOR ANY CLAIM
BROUGHT AGAINST PURCHASER BY ANY OTHER
PARTY. SOME STATES/PROVINCES DONOT ALLOW
THE EXCLUSION OR LIMITATION OF INCIDENTAL
OR CONSEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATION OR EXCLUSION MAY NOT APPLY TO
Section 13: Warranty Information
189
YOU.THISWARRANTYGIVESYOUSPECIFICLEGAL
RIGHTS, AND YOU MAY ALSO HAVE OTHER
RIGHTS, WHICH VARY FROM STATE TO STATE/
PROVINCE TO PROVINCE. THIS LIMITED
WARRANTY SHALL NOT EXTEND TO ANYONE
OTHER THAN THEORIGINALPURCHASEROF THIS
PRODUCT AND STATES PURCHASER'S EXCLUSIVE
REMEDY. IF ANY PORTION OF THIS LIMITED
WARRANTY IS HELD ILLEGAL OR
UNENFORCEABLE BY REASON OF ANY LAW, SUCH
PARTIAL ILLEGALITY OR UNENFORCEABILITY
SHALL NOT AFFECT THE ENFORCEABILITY FOR
THE REMAINDER OF THIS LIMITED WARRANTY
WHICH PURCHASER ACKNOWLEDGES IS AND
WILL ALWAYS BE CONSTRUED TO BE LIMITED BY
ITS TERMS OR AS LIMITED AS THE LAW PERMITS.
THE PARTIES UNDERSTAND THAT THE
PURCHASERMAYUSETHIRD-PARTYSOFTWAREOR
EQUIPMENT IN CONJUNCTION WITH THE
PRODUCT. SAMSUNG MAKES NO WARRANTIES OR
REPRESENTATIONS AND THERE ARE NO
CONDITIONS, EXPRESS OR IMPLIED, STATUTORY
OR OTHERWISE, AS TO THE QUALITY,
CAPABILITIES, OPERATIONS, PERFORMANCE OR
SUITABILITY OF ANY THIRDPARTY SOFTWARE OR
EQUIPMENT, WHETHER SUCH THIRD-PARTY
SOFTWARE OR EQUIPMENT IS INCLUDED WITH
THE PRODUCT DISTRIBUTED BY SAMSUNG OR
OTHERWISE, INCLUDING THE ABILITY TO
INTEGRATEANYSUCHSOFTWAREOREQUIPMENT
WITHTHEPRODUCT. THEQUALITY, CAPABILITIES,
OPERATIONS, PERFORMANCE AND SUITABILITY
190
Standard Limited Warranty
OF ANY SUCH THIRD-PARTY SOFTWARE OR
EQUIPMENT LIE SOLELY WITH THE PURCHASER
AND THE DIRECT VENDOR, OWNER OR SUPPLIER
OF SUCH THIRD-PARTY SOFTWARE OR
EQUIPMENT, AS THE CASE MAY BE.
This Limited Warranty allocates risk of Product failure
between Purchaser and SAMSUNG, and SAMSUNG's
Product pricing reflects this allocation of risk and the
limitations of liability contained in this Limited
Warranty. The agents, employees, distributors, and
dealers of SAMSUNG are not authorized to make
modifications to this Limited Warranty, or make
additional warranties binding on SAMSUNG.
Accordingly, additional statements such as dealer
advertising or presentation, whether oral or written, do
not constitute warranties by SAMSUNG and should not
be relied upon.
Samsung Telecommunications America, L.P.
1301 East Lookout Drive
Richardson, Texas 75082
Phone: 1-800-SAMSUNG
Phone: 1-888-987-HELP (4357)
©2005 Samsung Telecommunications America,L.P. All
rights reserved.
No reproduction in whole or in part allowed without
prior written approval. Specifications and availability
subject to change without notice.
Printed in South Korea
Section 13: Warranty Information
191
192
About 118
Index
Activation 119
Disconnect 120
Registered List 120
Search 119
Service Profiles 118
Settings 121
Numerics
1-touch dialing 75
2-touch dialing 75
3G protocol icon 22
3-touch dialing 76
911, notes about 108
A
Bluetooth icon 23
C
Calculator 149
Calendar 142
Call Functions 31
Answering a Call 32
Call Histories 33
Roaming 37
Adding a New Contact En-
try 67
Alarm clock
icon 23
snooze 146
turn off the alarm 145
Answer options 115
Auto answer 115
Auto answer icon 25
Auto delete 114
Call history
calls using 35
definition 33
deleting entry 36
icons 34
new contact 35
Call Options 115
Callback # 113
Camera/Video hot key 18
Change lock 108
Changing Message Set-
tings 99
Auto retry 116
B
Backlight settings 105
Backup to last menu 52
Banner, creating 104
Battery
Charger, desktop 27
Clear key 20
charging 26
indicator 27
removing 26
strength icon 24
Command Keys 20
Contacts
p pause & t pause 69
Bluetooth
193
Events, viewing calendar
Creating and Sending New
Messages 90
Creating and Sending Pix/
Flix messages 91
Creating and Sending Text
message 90
Exit Mobile Web 155
F
Fast fact, description 12
File Viewer 150
Finding a Contacts Entry
D
Desktop charger 27
Dialing
Finding My Phone Number
one-touch 75
three-touch 76
two-touch 75
Folder
drafts 86
inbox 83
Disable alarm 145
Display
animation 103
backlight 105
banner 104
language 111
screen icons 22
G
Gallery 131
Get New Pix 129
Get News & Info 136
Get Pix & Flix 126
Get Tunes & Tones 124
Getting Started 9
Activating Your Phone 10
Understanding this User
Manual 11
Draft messages 86
Drafts folder 86
E
Emergency numbers
lock mode 109
End key 21
Voicemail 10
Entering Text 59
Changing the Text Entry
Mode 60
GPS icon 23
Groups
creating 71
Entering Numbers 63
Entering Symbols 62
Entering Upper and Low-
er Case 62
move entries from/to 70
send messages to 71
send pix msg to 72
viewing 70
194
Launch Mobile Web 154
Left soft key 20
Links 157
H
Hard pause 69
Health and Safety Infor-
mation 159
Location 110
Lock code, changing 108
Lock phone 107
M
Memory Card Storage 27
Memos, editing 148
Menu Navigation 51
Menu Outline 54
I
Icons
alarm on 25
battery strength 24
display 22
Dormant 23
ringer off 24
signal strength 22
TTY 24
Menu shortcuts 52
Menu, in-use option 53
Inbox folder 83
Indicator
Message folder
drafts 86
inbox 83
battery strength 24
Bluetooth active 23
Bluetooth connected 24
calendar appointment 24
digital 22
EVDO 2G protocol 23
missed calls 24
new message 24
no service 23
Message settings 112
Messages, receive in call
Messaging 79
Types of Messages 80
Mobile Web 153
Keys 138
roaming 22
soft keys 155
signal strength 22
speakerphone 24
SSL 23
voice privacy 23
voicemail 24
Mode
call answer 115
entry 113
Mp3 150
In-use menu 53
Msg Setting 112
Multimedia 123
My Name Card 76
L
Language setting 111
195
add a new event 142
My phone # 77
N
Navigate the Web 155
Navigation key 22
Navigation key shortcuts
Powering off 10
Powering on 10
R
Receive messages in call
Receive text messages 88
Removing battery 26
Reset phone 117
Restrict calls 110
Restriction 110
Retrieving a Message 88
Retrieving New Message
New message icon 24
No service indicator 23
Notepad 147
Notes and tips 12
Notes, description 12
O
One-touch dialing 75
Organizer 141
Alarm Clock 144
calculator 149
Calendar 142
file viewer 150
Mp3 150
Return to last menu 52
Reviewing sent messages
Right soft key 20
Ringer off icon 24
Roam option 37
Roaming
Definition 37
options 37
notepad 147
view an event 143
world clock 146
P
Phone Memory Storage 30
Roaming indicator 22
Pix messages
S
rejecting 82
view later 83
Security
change lock 108
lock phone 107
restriction 110
voice privacy 109
Pix/Flix messages 91
Place a call while using
Mobile Web 157
Planner
Send key 21
196
Tip
Set an alarm 144
Tip, description 12
Tips
Settings 101
backlight 105
banner 104
description 12
change lock 108
Data 116
language 111
lock phone 107
Resetting Your Phone
Ringer Settings 117
Security Settings 106
Today 142
TransFlash 150
TransFlash Memory 27
TTY mode 38
Turn your phone off 10
Turn your phone on 10
Turning Your Phone On
and Off 10
Shortcut List 105
Two-second pause 69
Two-touch dialing 75
Shortcut to menus 52
Signal strength icon 22
Snooze 146
Speed dial, assigning 76
Standard Limited Warran-
U
Understanding Your Con-
tact List
Finding a Contact Entry
ty
Standard Limited War-
ranty 186
Store numbers, shortcuts
Understanding Your Con-
tacts 65
Adding a New Contact
Entry 67
Deleting a Contact Entry
Editing an Existing Con-
Finding My Phone Num-
ber 77
Storing numbers after a
call 74
T
Take Pix 129
Text messages, receiving
Speed Dialing 75
197
checking phone status
digit dial 44
features 43
name dial 45
name lookup 46
send text message 46
settings 39
UnderstandingYourPhone
Battery 26
Display Screen 22
Features of Your Phone
Front View of Your Phone
V
Voice Signal menu 38
Voicemail 89
Voicemail, viewing mes-
sages 89
V CAST Video
browsing/playing clips
configuring alerts 129
deleting clips 128
description 126
VoiceMode
adapting VoiceMode 93
advanced features 97
creating a text message
downloading clips 127
Vibrate mode icon 24
Video clips 126
View an event, calendar
description 93
using choice lists 97
W
view pix msg later 83
voice call icon 23
Voice mail
listening to 11
setup 10
Wallpaper, choosing 103
Warranty Information 185
World clock 146
Voice mail icon 24
Voice memos 48
Voice notes
renaming 49
Voice Privacy 109
Voice Signal
adaptation 41
198
|